Filtern
Erscheinungsjahr
- 2017 (341) (entfernen)
Dokumenttyp
- Beitrag zu einem Tagungsband (341) (entfernen)
Sprache
- Englisch (246)
- Deutsch (94)
- Portugiesisch (1)
Schlagworte
- Concrete (11)
- Korrosion (7)
- Simulation (7)
- Zerstörungsfreie Prüfung (7)
- Cement (6)
- Fire (6)
- Process Analytical Technology (6)
- Wear (6)
- CFK (5)
- Eigenspannungen (5)
The fine fraction of bottom ash from municipal solid waste incineration is characterized of both a high pollution and relevant resource potential. Methods for studying the environmental behaviour of solid residues are leaching tests. Various leaching test are adopted all over Europe with liquid to solid ratio of 2 or 10 l/kg. In Germany three different leaching Tests are valid with the commencement of the draft of the ordinance of reuse of mineral waste as alternative building ordinance. Comparing two batch tests, only the concentration for chloride is comparable. To evaluate the metal resource potential in the sand fraction wet chemical Methods have been applied. Methodical problems were caused mainly by the material heterogeneity and especially for precious metals due to their low concentration around 1 mg/kg. Other Methods have been available, but hardly applicable.
Gegenstand des Projekts ist die Prüfung der Umweltbeständigkeit und -verträglichkeit von Materialien und Produkten hinsichtlich der Emission von potenziellen Schadstoffen in die Umwelt. Hierzu werden chemisch-physikalische Einflüsse (Bewitterung) und mikrobielle Beanspruchungen an Modellmaterialien evaluiert. So werden die Freisetzungsraten von Schadstoffen in Abhängigkeit der Beanspruchung beschrieben. Als Modellmaterialien kommen die Polymere Polycarbonat, Polytetrafluorethylen, Polystyrol und Polypropylen zum Einsatz. Synergistische Effekte der Bewitterungsparameter und der mikrobiologischen Beanspruchung sollen dabei ebenso betrachtet werden, wie die gezielte Alterung. Auch findet eine Beschreibung des Verhaltens der ausgetragenen Schadstoffe in den Umweltkompartimenten Boden oder Wasser statt. Hier sind mit Hilfe der zu entwickelnden Screening- und non-Target-Analyseverfahren die Transformation und der Metabolismus durch Mikroorganismen zu beschreiben. Aus den Ergebnissen sollen Korrelationen zwischen den künstlichen Alterungsverfahren und realen Szenarien abgeleitet werden, die es gestatten, Schnellprüfverfahren zu etablieren, die die Simulation der realen Beanspruchungen im Zeitraffermodell anwendbar machen. Somit sollen standardisierbare Schnellbeanspruchungs-verfahren erarbeitet werden, die als Prüfeinrichtungen etabliert werden und von externen Auftraggebern zur Prüfung der Umweltbeständigkeit und -verträglichkeit von neuen Materialien genutzt werden können. Die Umweltwirkungen (chemisch-physikalisch und mikrobiologisch) sollen so definiert eingesetzt werden, dass eine reproduzierbare Prüfung möglich wird. Aus diesen Verfahren und Methoden sollen Normen abgeleitet werden, die eine standardisierte Materialprüfung ermöglichen.
The plastic deformation results in irreversible microstructure changes in the steel, which can be considered as the initial stage of the fracture process. However, detecting, monitoring and evaluating, damage states and small defects non-destructively in advance still proves challenging. It was reported in literature the phenomenon of the spontaneous emergence of weak magnetic fields in structural steels and pipelines, which originates due to heterogeneous mechanical and / or thermal stresses. This observation is not associated with induced phase transformations by deformation and appears to be a promising tool for the prior characterization of damage in ferromagnetic steels. To provide a better understanding of the physical bases of the process, the magnetic microstructure of such materials and the change of magnetic domains after undergoing plastic deformation were studied. For this purpose, a colloidal solution with paramagnetic particles in the nanometer scale (ferrofluid) was used, through the Bitter technique, in order to, not only observe a change in size of the magnetic domains of the material, but also changes in their morphology. Ferritic steels with different carbon contents (0.08%; 0.22% and 0.45%) were studied in this work.
The efficiency of gas sensor application for facilitating the safe use of hydrogen depends considerably on the sensor response to a change in hydrogen concentration. Therefore, the response time has been measured for five different-type commercially available hydrogen sensors. Experiments showed that all these sensors surpass the ISO 26142 standard; for the response times t90 values of 2 s to 16 s were estimated. Results can be fitted with an exponential or sigmoidal function. It can be demonstrated that the results on transient behaviour depend on both the operating parameters of sensors and Investigation methods, as well as on the experimental conditions: gas change rate and concentration jump.
The present paper provides a discussion on all these topics and it offers solutions for it. The authors present an analytical solution of a Delta J based crack driving force based on an R6 type approach but modified for cyclic loading. The gradual build-up of the crack closure effect is modelled by the so-called cyclic R curve which describes the crack size dependency of the fatigue crack propagation threshold in the short crack regime. It is explained how the cyclic R curve is experimentally determined and how it can be estimated by a modified Kitagawa-Takahashi approach.
In modernen Stahlkonstruktionen werden immer häufiger hochfeste Feinkornbaustähle erfolgreich eingesetzt. Dies resultiert aus dem aktuellen Bestreben, leichte Komponenten zu fertigen und damit die Energie- und Ressourceneffizienz zu steigern. Die Herausforderungen an die Auslegung und Herstellung geschweißter Bauteile nimmt jedoch mit steigenden Festigkeiten und abnehmenden Dehnungsreserven der eingesetzten Werkstoffe zu. So können hohe Schweißeigenspannungen die Beanspruchbarkeit und Bauteilsicherheit kritisch herabsetzen. Untersuchungen zeigten bereits deutliche Einflüsse von Werkstoff, Wärmeführung sowie Schweißprozessparametern und der um-gebenden Konstruktion der Schweißnaht auf den Beanspruchungszustand geschweißter Bauteile. Der Einsatz moderner modifizierter Sprühlichtbogenprozesse (mod.SLB) gestattet in diesen Zusammenhang neben den bekannten wirtschaftlichen Vorteilen das Schweißen einer deutlich schmaleren Nahtgeometrie. Aufgrund des resultierenden reduzierten Gesamtwärmeeintrages sind deutlich geringere schweißbedingte Beanspruchungen und eine höhere Beanspruchbarkeit hochfester Schweißkonstruktionen erreichbar. Unter Nutzung spezieller Prüfanlagen konnten mehrlagige Schweißexperimente zur Analyse des Einflusses der Nahtgeometrie auf die Eigenspannungsausbildung und Gesamtbeanspruchung hochfester Schweißverbindungen bei bauteilähnlichen Einspannbedingungen durchgeführt werden. Für die reduzierten Nahtvolumina zeigte sich eine signifikante Absenkung des Beanspruchungsniveaus während des Schweißens und nach der Abkühlung.
Für die Klassifizierung sowie die sichere Handhabung und Nutzung von Chemikalien und anderen Stoffen wurden spezielle standardisierte Testmethoden entwickelt, die weltweit zum Einsatz kommen. Die Ableitung von Sicherheitsmaßnahmen durch Experten erfordert, dass aus diesen Untersuchungen verlässliche Daten gewonnen werden. Ringversuche sind ein wesentliches Element bei der Methodenentwicklung (-validierung) und für die Qualitätssicherung von Laboratorien.
Die Testmethode DIN EN 15188:2007 dient der Bestimmung des Selbstentzündungsverhaltens von Schüttgütern und Stäuben. Experimentelle Grundlage für die Beschreibung des Selbstentzündungsverhaltens eines bestimmten Materials ist die Bestimmung der Selbstentzündungstemperaturen (TSE) von Proben verschiedener Größen mit Hilfe isoperiboler Warmlagerungsversuche. Die so ermittelten Versuchsdaten ergeben die Abhängigkeit der Selbstentzündungstemperaturen vom Lagervolumen. Zweck einer schrittweise aufgebauten Serie von Ringversuchen und internen Labortests war die Identifizierung von Schwächen der bestehenden Methode bzw. von in der Laborpraxis auftretenden Mängeln bei der Anwendung der Methode, die Validierung der modifizierten und verbesserten Methode sowie die Bestimmung einer allgemeingültigen (Mess-)Unsicherheit dieser modifizierten Methode.
Originally introduced in the field of earthquake engineering hybrid testing, i.e. the simultaneous combined application of numerical simulation techniques and execution of experiments, is nowadays used in different areas of experimental analysis. The focus of this paper is on the presentation of the so-called substructuring method as a hybrid method in fire engineering. Motivation are EU standards for fire resistance tests of columns or beams. According to these codes building elements are considered as stand-alone elements whereas in real fires each building element interacts with its adjacent elements. Therefore, to conduct a fire test in a more realistic fashion, the concept of hybrid substructuring as a special experimental technique has been adopted to fire engineering. Due to this concept the entire building, which is exposed to a real fire, is decomposed into two parts. One part is represented by the building element under test in a special furnace, whereas the remaining building environment is simulated by a model, based on the equations of thermomechanics. The paper addresses the historical development of the substructuring method in fire engineering supplemented by presentation of the results of realized fire resistance tests in substructuring mode on different types of specimens.
A two-dimensional numerical mesoscale model has been created representing a microstructure of a typical 2205/1.4462 duplex stainless steel to further elucidate the mechanisms of hydrogen-assisted crack initiation and propagation in multiphase non-hydride forming metallic microstructures. Hydrogen-assisted cracking (HAC) was simulated by considering different stress and strain behavior as well as different diffusion behavior in both phases. For simulation of crack initiation and propagation, the element elimination technique has been applied. The model allows the simulation of path-free crack propagation which contributes to a better understanding of the HAC process in two-phase microstructures. As a particular result, the analyses revealed that a global macroscopic elastic deformation might already cause plastic deformation in both phases entailing respective HAC.
The work presents the effects of the change of the laser cladding parameters on microstructure, chemical composition and mechanical properties of Inconel 686 overlays (coatings). To obtain the best quality of These coatings the various parameters of laser cladding such as the power density of the laser beam, the laser beam velocity and overlapping ratio of the weld tracks were applied. The substrates were boilers plate made of the 13CrMo4-5 steel. Ni - base alloys characterize by the excellent high-temperature corrosion resistance, good strength and good ability to work in aggressive environments. This could be achieved by the reduction of the substrate melting and its dissolution into the overlays. The microstructure, chemical composition of the obtained overlays were investigated by means of a light microscope, a scanning electron microscope (SEM) equipped with the EDS detector. The overlays had cellular-dendritic structure. The variations of the chemical composition (especially Mo, Ni and W ) in the interdendritic and dendritic regions were observed. The interdendritic regions were enriched during solidifications in Mo and W and had lower content of Ni.