Filtern
Dokumenttyp
Sprache
- Englisch (13) (entfernen)
Referierte Publikation
- nein (13) (entfernen)
Schlagworte
- Welding simulation (13) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (1)
This article is devoted to the study of the bulging effect in deep penetration laser beam welding. The numerical results of the investigations are based upon experimental results from previous studies to reveal the relationship between the bulging effect and the hot cracking formation, as well as the mixing of alloying elements in the weld pool. The widening of the molten pool in its center area can be observed in full penetration as well as in partial penetration welds on 8 mm and 12 mm thick structural steel plates, respectively. The weld pool shape is extracted from the simulations to evaluate the extent of the necking of the solidification line as well as the bulging phenomena and its influence on the hot cracking phenomena. Relying on an earlier numerical study utilizing a fixed keyhole, simulation models considering a dynamic keyhole are developed thereto. Additionally, the mixing behavior of alloying elements during partial penetration is investigated. The link between the bulge and the studied phenomena is found to be significant.
The present investigations cover different relevant influences on the numerical calculation of welding-induced distortion. Therefore, a single-layer pulsed gas metal arc (GMA) weld of structural Steel S355J2+N with a thickness Öf5 mm is experimentally and numerically investigated. The influences of mesh density, tack-welds, and continuous cooling transformation (CCT) diagrams on welding-induced distortion are studied. The quality and quantity of These effects are clarified based on the used experimental and numerical set up. The occurring differences between the investigated cases achieve significant values. Consequently, prediction of welding-induced distortion can be improved considering the present investigations.
Fusion welding is widely used in the automotive industry to join metal structures. It is well-known that distortions and residual stresses occur during and after the welding process. Many procedures exist to decrease these negative heat effects of welding, but are often coupled with highly cost intensive experiments. The implementation of a welding Simulation tool to reduce this very expensive experimental procedures is therefore of high interest. Despite the fact that the automotive industry is a key sector for Simulation procedures, welding Simulation Software is nevertheless not yet widely implemented. This is mainly due to the complexity of the Simulation tools requiring expert users and the resulting high time to Solution.
In this study, a new fast thermo-mechanical Simulation of a complex and large laser beam welded automotive sheet metal assembly with several non linear welds is simulated. Assumptions and simplifications of the complex physical welding phenomenon, which are made to keep the computational cost and the complexity of the Simulation in an industrial frame, are discussed. The calibration time of the phenomenological heat source model has been optimized with a very fast analytical thermal model and the resulting simulated temperature fields match perfectly with the measured ones. Additionally, the user experience and the time-to-solution are kept within a reasonable time frame for arr industrial environment. All Simulation results are validated with experimental results.
The usage of continuous cooling transformation (CCT) diagrams in numerical welding simulations is state of the art. Nevertheless, specifications provide limits in chemical composition of materials which result in different CCT behavior and CCT diagrams, respectively. Therefore, it is necessary to analyze the influence of variations in CCT diagrams on the developing residual stresses. In the present paper, four CCT diagrams and their effect on numerical calculation of residual stresses are investigated for the widely used structural steel S355J2 + N welded by the gas metal arc welding (GMAW) process. Rather than performing an arbitrary adjustment of CCT behavior, four justifiable data sets were used as input to the numerical calculation: data available in the Sysweld database, experimental data acquired through Gleeble dilatometry tests, and TTT/CCT predictions calculated from the JMatPro and Edison Welding Institute (EWI) Virtual Joining Portal software. The performed numerical analyses resulted in noticeable deviations in residual stresses considering the different CCT diagrams. Furthermore, possibilities to improve the prediction of distortions and residual stress based on CCT behavior are discussed.
For differentiating the applicability of various numerical welding Simulation methods as well as unifying the prerequisites and the Steps to be taken in Simulation, normative codes are required for the user. Since any standard-like documents are currently still lacking in this field, DIN German Institute for Standardization has set up the Standards Committee NA 092-00-29-AA "Welding Simulation" dealing with the preparation of respective documents. This committee was initiated in partnership with the joint committee FA 12 "Weld Simulation on Application" of the Research Association of DVS German Welding Society.
The objective of this Standardization work in the field of numerical welding Simulation is to prepare a DIN SPEC with a view to standardizing the approaches to the Simulation of various welding phenomena and processes over the long run. In a draft version of DIN SPEC 32534 that has already been prepared by the above mentioned Committee, the structure of the primary document was stated. The primary document specifies the application fields and the key terms of welding Simulation. In addition, the generally valid Simulation structure has been established which is intended to serve as a recommendation for customers and suppliers in formulating and handling a Service order as well as for persons who Start doing welding Simulation for the first time.
This article focuses on the presentation of the new DIN SPEC 32534-1 explaining the major Simulation Steps. It additionally addresses the Classification of the secondary documents depending on the welding process and on the desired Simulation result. Finally, it gives an overview of the other subject areas dealt with in the Standards Committee NA 092-00-29-AA "Welding Simulation" as well as of the international activities in this field.
Fast temperature field generation for welding simulation and reduction of experimental effort
(2009)
The quality of welding processes is governed by the occurring induced distortions yielding an
increase in production costs due to necessary reworking. Especially for more complex specimens
it is difficult to evaluate the optimal configuration of welding sequences in order to
minimise the distortion. Even experienced welding operators can solve this task only by trial
and error which is time and cost consuming.
In modern engineering the application of welding simulation is already known to be able to
analyse the heat effects of welding virtually. However, the welding process is governed by
complex physical interactions. Thus, recent weld thermal models are based on many simplifications.
The state of the art is to apply numerical methods in order to solve the transient heat
conduction equation. Therefore, it is not possible to use the real process parameters as input
for the mathematical model. The model parameters which allow calculating a temperature
field that is in best agreement with the experiments cannot be defined directly but inversely by
multiple simulations runs. In case of numerical simulation software based on finite discretisation
schemes this approach is very time consuming and requires expert users. The weld
thermal model contains an initial weakness which has to be adapted by finding an optimal set
of model parameters. This process of calibration is often done against few experiments. The
range of model validity is limited. An extension can be obtained by performing a calibration
against multiple experiments.
The focus of the paper is to show a combined modelling technique which provides an efficient
solution of the inverse heat conduction problem mentioned above. On the one hand the inverse
problem is solved by application of fast weld thermal models which are closed form
solutions of the heat conduction equation. In addition, a global optimisation algorithm allows
an automated calibration of the weld thermal model. This technique is able to provide a temperature
field automatically that fits the experimental one with high accuracy within minutes
on ordinary office computers. This fast paradigm permits confirming the application of welding
simulation in an industrial environment as automotive industry.
On the other hand, the initial model weakness is compensated by calibrating the model
against multiple experiments. The unknown relationship between model and process parameters
is approximated by a neural network. The validity of the model is increased successively
and enables to decrease experimental effort. For a test case it is shown, that this approach
yields accurate temperature fields within very short amount of time for unknown process parameters
as input data to the model contributing to the requirement to construct a substitute
system of the real welding process.