Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Tagungsband (62) (entfernen)
Referierte Publikation
- nein (62) (entfernen)
Schlagworte
- Radar (12)
- Concrete (10)
- Ultrasonic echo (9)
- Beton (6)
- Impact-echo (6)
- NDT (6)
- Impact-Echo (5)
- Zerstörungsfreie Prüfung (5)
- Data fusion (4)
- Ultraschallecho (4)
Organisationseinheit der BAM
The LAUS: First Applications of a New System for Ultrasonic Imaging of Very Concrete Structures
(2019)
The LAUS (Large Aperture Ultrasonic System) has been developed to image very thick concrete structures, which are not accessible for commercial systems. The device and the corresponding software is the result of joint Research of BAM, an ultrasonic instrument manufacturer and University of Kassel, Germany. It consists of 12 separate Arrays of 32 point-contact shear wave transducers each, which can be deployed in flexible configurations. Each array is combined with battery and transmitter, receiver and wireless communication electronics.
Three case histories are presented. First the system was deployed on a 5-m thick heavily reinforced foundation slab.
The reflection of the slab’s bottom was imaged clearly. In addition, a multiple reflection was registered, thus giving hope that even thicker elements might be imaged by the instrument. Second, the LAUS was used to investigate a massive bridge girder where a heavy rainstorm during concreting had led to imperfections that were visible after removing the formwork was removed. The LAUS could image tendon ducts in 1.8m depth and the backwall closely behind them. Some limited areas showed blurred reflections and were checked by drill holes; these areas were affected by diffuse damage which could be repaired by injections. Third, a large retaining wall was checked for thickness.
Meanwhile, the LAUS has been used in underground waste deposits (nuclear and other) for quality assurance of sealing plugs. A confirmed penetration depth of about 7 m has been reached.
LAUS - Erste praktische Erfahrungen mit einem neuartigen Ultraschallsystem großer Eindringtiefe
(2018)
Konventionelle Systeme zur Ultraschall-Echo-Prüfung von Betonbauteilen sind in ihrer Eindringtiefe auf etwa einem Meter begrenzt. Zur Prüfung stärkerer Objekte war die Entwicklung eines neuartigen Prüfsystems notwendig. Das LAUS-System (Large Aperture UltraSound) besteht aus 12 einzelnen Arrays, die mit jeweils 32 Einzelprüfköpfen (Scherwellen, 25 – 50 kHz) als Sender oder Empfänger betrieben werden können. Sie werden unabhängig auf Betonoberflächen mit Unterdruck befestigt und kommunizieren drahtlos untereinander und mit der Zentraleinheit. Alle möglichen Kombinationen ergeben 132 Einzelmessungen, die zur Rekonstruktion des durchschallten Volumens genutzt werden. Mehrere dieser Datensätze lassen sich zu einer 3D-Auswertung kombinieren. Das System wurde an mehreren Testobjekten und Bauwerken erfolgreich erprobt. So konnte die fünf Meter dicke, sehr stark bewehrte Fundamentplatte des Fallturms auf dem BAM-Testgelände bei Horstwalde durchschallt werden. Ein zweites Beispiel ist die erfolgreiche Detektion von Spannkanälen in 1,8 m Tiefe in einem massiven Brückenbauwerk.
We present the results of a machine learning (ML)- inspired data fusion approach, applied to multi-sensory nondestructive testing (NDT) data. Our dataset consists of Impact-Echo (IE), Ultrasonic Pulse Echo (US) and Ground Penetrating Radar (GPR) measurements collected on large-scale concrete specimens with built–in simulated honeycombing defects. In a previous study we were able to improve the detectability of honeycombs by fusing the information from the three different sensors with the density based clustering algorithm DBSCAN. We demonstrated the advantage of data fusion in reducing the false positives up to 10% compared to the best single sensor, thus, improving the detectability of the defects. The main objective of this contribution is to investigate the generality, i.e. whether the conclusions from one specimen can be adapted to the other. The effectiveness of the proposed approach on a separate full-scale concrete specimen was evaluated.
Laser-induced breakdown spectroscopy (LIBS) is a combination of laser ablation and optical emission spectroscopy. Due to the possibility of direct measurements on the sample surface with a minimum of sample preparation investigations of building materials can be conducted quite fast. In combination with a scanning technique (translation stage or scanning mirrors head) 2D element distributions of harmful species like chlorides and alkalis are evaluated with a sub-mm resolution. By scanning a surface of typically 100 mm x 100 mm the heterogeneity of the material may be considered. LIBS is capable to identify hot spots in element concentration with a resolution of 0.1 mm or even smaller. A LIBS-system for the on-site application on building materials is, in cooperation with system developers and companies which will use this technique for investigation on real structures, under test at BAM. We present an example. Further work will focus on providing guidelines to establish LIBS as a standard procedure for chemical investigations of building materials.
Investigations for the improvement of SAFT imaging quality of a large aperture ultrasonic system
(2015)
In parallel to the hardware development of an ultrasonic system for the investigation of thick concrete structures, a software package for interactive reconstruction of data for that special arrangement of ultrasonic transducers was developed. The system which is presented in a further contribution to this conference as "large aperture ultrasonic system" (LAUS) requires special features to the evaluation software because measuring positions can be in a non equidistant grid and there is the possibility to improve the measurement by adding measuring points interactively.
Starting from theoretical considerations to the image generation by measuring arrangements of synthetic aperture problems, solution approaches for imaging with SAFT (Synthetic Aperture Focusing Technique) algorithms in space and frequency domain of data from insufficient grid density are presented.
A wide range of issues that may arise in the application is precalculated by simulations and experimental studies, so that unavoidable artifacts can be identified and classified. A special focus is put on the application of thick concrete structures considering missing measuring points in a grid, grating lobes and surface waves.
The research project "Ultrasonic Net for Concrete Monitoring (UNeCOM)" aims at developing a methodology for an embedded ultrasonic network for the condition assessment of infrastructure constructions. Civil engineering structures made of concrete, which are located in tectonically active regions or undergo special loading conditions, may require continuous monitoring. It is important to assess the condition of the building and its stability to recognise and classify the effect of a seismic event or evolving damage at early stages before failure occurs. Embedded ultrasonic sensors offer the possibility to detect changes in the material and degradation mechanisms from inside the structure in areas which are difficult or impossible to inspect otherwise. In contrast to conventional ultrasonic testing methods, where the concrete surfaces are scanned with ultrasound probes, this new approach uses sensors, which are embedded into concrete, eliminating the effect of variable coupling conditions between sensors and concrete. This method allows an integral detection of changes in the concrete structure, for example due to seismic activities, to detect mechanical impacts, as well as degradation of the material due to overloading. Such methods have great relevance especially for the monitoring of constructions like power plants, bridges, offshore structures and other structures with high technical safety requirements. The sensor network can be controlled remotely through the internet which is also being used for data transfer. The embedded sensor network is designed to monitor structural damage and concrete degradation globally with high sensitivity.
Laser induced breakdown spectroscopy (LIBS) - visualization of ion transport processes in concrete
(2014)
Laser induced breakdown spectroscopy (LIBS) is a combination of laser ablation and optical emission spectroscopy. Due to the possibility of direct measurements on the sample surface and a minimum of sample preparation investigations of building materials can be conducted quite fast. In combination with a scanning technique (translation stage or scanning mirrors head) the element distributions are evaluated with mm resolution. Thus the heterogeneity of the material may be considered. This is a significant advantage compared to standard procedures. LIBS measurements are also time and cost saving in comparison to standard methods. The automated measurement procedures minimize the liability for errors. All elements are detectable. Results can be quantified after calibration. At BAM LIBS has been successfully applied for the investigation of distribution and transport of different ions in building materials. Quantitative measurements are performed for chlorine, sodium, potassium, sulfur, lithium and hydrogen. In addition the identification of substances and the evaluation of quantitative ratios by means of an integrated marker are possible. An overview about the principle and the possibilities of LIBS investigations of building materials is presented and typical applications are shown. The LIBS technique is close to practical application on-site.
Die drei Beispiele zerstörungsfreier Prüfungen an Spannbetonbrücken zeigen unterschiedliche Problemstellungen und deren Lösung mit unterschiedlichen Ansätzen.
Allen drei Beispielen gemeinsam ist die Verwendung kommerzieller Geräte. Diese werden von verschiedenen Anbietern bereitgestellt. Eine weitere Gemeinsamkeit ist, dass die Grundgeräte durch zusätzliche Maßnahmen ergänzt. Erst dann ist der gewünschte Untersuchungserfolg sicher gestellt.
Im ersten Beispiel wurde die vom Auftraggeber geforderte Präzision dadurch erreicht, dass systematische Voruntersuchungen stattfanden. Die Übertragung der Lokalisierung direkt auf die Betonoberfläche stellte sicher, dass keinen Informationsverluste an die nachfolgenden Aufgaben auftraten.
Das zweite Beispiel zeigt den Nutzen von Automatisierung und Kombination von Verfahren. Damit können dem Auftraggeber die notwendigen Angaben über Einbauteile mit großer Detaitreue und leicht verständlicher Visualisierung aufbereitet werden. Der abschließende Bericht zeigt, wie vorhandene Auswertungen sinnvoll durch noch in der Forschung befindliche Ansätze bereichert werden.
Insgesamt ist die zerstörungsfreie Prüfung in der Lage, an Brücken preisrelevante Fragestellungen zu lösen. Voraussetzung hierfür ist eine sorgfältig geplante Vorgehensweise und ein sicheres Verständnis der Grundlage der eingesetzten Geräte und Auswertungsschritte.
Grouting defects, e.g. in post-tensioned structures or piped anchors may be identified by ultrasonic imaging. Since several years experiences are carried out with false color displayed phase values, which enable distinct localization of ungrouted regions.
In this contribution we report on progress in localizing grouting defects in tendon ducts, when they are only partly grouted and the unfilled part is not orientated into the direction of the measuring surface. This is frequently the case e.g. for box girder structures.
Düring the project specimens containing different types of grouting faults are investigated in Order to optimize measuring and evaluation techniques. A handheld linear array System (commercially available) is applied for fast 2D-measurement and subsequent phase sensitive 3D-imaging (new Software development).
In a large concrete wall specimen tendon ducts and real prestressing Systems containing grouting defects were built in. The ducts are partly covered by non prestressed reinforcement bars in order to investigate its disturbing influence. These included objects were investigated afterwards with the described methods. We report on large area measuring results, which were partly verified by y-radiography. In the frame of practical application results of measuring the position and extend of a blockade within a posttensioned structure are presen ted.