Filtern
Erscheinungsjahr
- 2018 (9) (entfernen)
Dokumenttyp
- Vortrag (4)
- Beitrag zu einem Tagungsband (2)
- Posterpräsentation (2)
- Zeitschriftenartikel (1)
Referierte Publikation
- nein (9)
Schlagworte
- Chloride (9) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (4)
This paper will address the relevance of chloride measurements in practice for durability condition assessment and a description of the working principle of LIBS will be given. Examples of chloride profiles obtained by the common wet chemical analysis will be shown and compared with results from LIBS measurements as to demonstrate the accuracy of the LIBS-technique. The latter will be supported by clear graphs. In addition examples on the extra information resulting from measurements performed with LIBS for improvement of condition assessment and prediction will be shown.
A big part of the infrastructure is made of concrete, which is a multiphase system made of cement, aggregates, water and pores. Concrete is often used in combination with steel as reinforced concrete. Environmental influences, especially the ingress of harmful ions in combination with the ingress of water, trigger different damage processes which reduce the designed lifetime of a structure. The ingress of chlorides from de-icing salt or sea water leads to corrosion of the reinforcement. In addition, the carbonation of the concrete may trigger the corrosion of the reinforcement. The ingress of alkalis from deicing salts may cause the expansion of the amorphous silica aggregates (alkali-silica reaction) through
formation of a swelling gel of calcium silicate hydrate if water is present. The ingress of sulphates may cause spalling of the concrete surface due to ettringite formation.
For the standard procedure in civil engineering cores are taken, cut in slices, grinded and the obtained homogenized powder is solved in acid and investigated by standard procedures.
BAM has developed the LIBS technique for the 2D evaluation of the chemical composition of concrete. The technique is established for automated laboratory use with high numbers of samples to investigate transport processes of harmful species (Cl-, CO2 , SO4 2-and alkalis) in concrete. Information about ingress depth and the quantitative values are important to estimate the remaining lifetime of the infrastructure. LIBS is a surface technique. To get information about the ingress depth, a drill core has to be taken and cut in the middle. The measurements are carried out at the cross section. The main advantages of LIBS are the direct measurement on the surface of the concrete, fast analysis (sample rate 100 Hz) with a spatial resolution of up to 100 µm, the consideration of the heterogeneity of the concrete and the possibility of automated measurements which save a lot of manpower and time. As an example the investigation of ingress profiles for standard diffusion and migration tests in civil engineering takes hours in comparison to just a few minutes using LIBS. At the same time a 2D-evaluation provides information about hot spots of elemental concentration which may not be found by standard methods.
The state of the art of LIBS technique for applications in civil engineering will be presented, including typical results of 2D investigation of concrete in laboratory. The performance is also demonstrated by examples for onsite applications using a mobile LIBS system. The road map to standardization is presented as well.
Concrete is often used in combination with steel as reinforced concrete. Environmental influences, especially the ingress of harmful ions in combination with the ingress of water, trigger different damage processes which reduce the designed lifetime of a structure. The ingress of chlorides from de-icing salt or sea water leads to corrosion of the reinforcement. Also the carbonation of the concrete may trigger the corrosion of the reinforcement. The ingress of alkalis from de-icing salts may cause the expansion of the amorphous silica aggregates (alkali-silica reaction) through formation of a swelling gel of calcium silicate hydrate if water is present. The ingress of sulfates may cause spalling of the concrete surface due to ettringite formation.
BAM has developed the LIBS technique for automated laboratory use with high numbers of samples to investigate transport processes of harmful species (Cl-, CO2, SO42- and alkalis) in concrete. Information about ingress depth and the quantitative values are important to estimate the remaining lifetime of the infrastructure. To get information about the ingress depth, a core has to be taken and cut in the middle. The measurements are carried out at the cross section. The main advantages of LIBS are the direct measurement on the surface of the concrete, fast analysis (sample rate 100 Hz) with a spatial resolution of up to 100 µm, the consideration of the heterogeneity of the concrete. The possibility of automated measurements saves a lot of manpower and time. At the same time a 2D-evaluation provides information about hot spots of elemental concentration which may not be found by standard methods.
Typical results of 2D investigation of concrete in laboratory will be presented. The performance is also demonstrated by examples for onsite applications using a mobile LIBS system. The road map to standardization is presented as well.
The durability and the lifetime of reinforced concrete structures can be drastically reduced by the influence of damage processes. One of the most common causes is chloride-induced corrosion, which is triggered by increased chloride content near the reinforcement. In a study, the chloride content should be determined directly at corrosion areas. The LIBS system used consists of a micro-chip laser (3 mJ, 100 Hz, 1.5ins) and two compact spectrometers covering the wavelength range of 177-355 nm (UV) and 750-940 nm (NIR). The analysis of the chloride content was carried out via the atomic chlorine spectral line 837.59 nm, using helium for signal amplification. Calibrations were carried out for quantitative chlorine measurements with 15 reference samples in the working range of 0.05 to 6.00 wt% chlorine. The calibration of the LIBS system was done according to DIN 32 645 and was tested for linearity. The determination of the quantitative chlorine contents was carried out on samples which were broken and thus have a high surface roughness. This requires real time correction of the focus point to compensate for the roughness of the samples. The poster shows spatially resolved element distributions and determined quantitative chloride concentrations near the corrosion Areas.
Schädigungen durch Korrosion der Bewehrung von Stahlbetonbauwerken unserer Infrastruktur sind u. a. mit dem Eindringen von Chloriden aus Tausalzen oder Meereswasser verbunden. In den Regelwerken sind daher Grenzwerte für den maximal zulässigen Chlorid-Gehalt deiniert. Die Einhaltung dieser Grenzwerte wird in der Praxis über die Entnahme von Bohrmehl oder die Entnahme von Bohrkernen überwacht. Die Bohrkerne werden in Zylindersegmente von meist zwei cm Höhe geschnitten, dann gemahlen und mit Säure aufgeschlossen. Das Bohrmehl aus verschiedenen Tiefenabschnitten kann direkt mit Säure aufgeschlossen werden. Der Chlorid-Gehalt im Aufschluss wird dann meist mittels Potentiometrischer Titration bestimmt. Dieses Vorgehen ist mit einem hohen Zeit- und Personalaufwand verbunden. Die Information über die Heterogenität des Betons geht dabei aufgrund der Homogenisierung bei der Probenvorbereitung oder bei der Entnahme von Bohrmehl verloren. Der Chlorid-Gehalt wird in der homogenisierten Betonprobe (Zement, Wasser und Gesteinskörnung) analysiert und die Werte bezogen auf den Beton angegeben. Demgegenüber sind die Grenzwerte des maximal zulässigen Chlorid-Gehaltes auf den Zement bezogen. Da die Rezeptur des Betons fast nie verfügbar ist, wird die Umrechnung vom Gehalt bezogen auf den Beton zum Gehalt bezogen auf den Zement über eine zusätzliche Analyse oder durch Abschätzung durchgeführt.
Als Ergänzung zum Standardverfahren wurde in der Bundesanstalt für Materialforschung und –prüfung das LIBS- Verfahren (Laser Induced Breakdown Spectroscopy) für die Untersuchung der chemischen Zusammensetzung von Baustofen im Labor seit einigen Jahren erfolgreich eingesetzt. In einem vom Bundeswirtschatsministerium geförderten Projekt sollten die sich ergänzenden Kompetenzen eines Forschungspartners (BAM), eines Geräteherstellers (SECOPTA analytics GmbH) und eines potentiellen Anwenders (Ingenieurbüro Specht, Kalleja und Partner) in die Entwicklung eines mobilen LIBS Gerätes (BauLIBS) eingehen. Dieser Artikel stellt das Messprinzip und seine wesentlichen Vorteile vor, gibt einen Überblick über das entwickelte mobile LIBS-Gerät und seine Leistungsparameter.
Anschließend werden einige erfolgreiche Anwendungsbeispiele zur Untersuchung von Schädigungsprozessen direkt an der Beton-Infrastruktur vorgestellt und ein Ausblick auf zuküntige Entwicklungen gegeben. Das BauLIBS-Gerät liefert dem sachkundigen Planer Daten für die Bewertung des Istzustandes von Bauwerken unserer Infrastruktur durch die zweidimensionale Erfassung von Elementverteilungen. Typische Anwendungen sind die Erfassung von Chlor, Schwefel, Kohlenstof, Natrium, Kalium und Lithium in Beton oder als Qualitätssicherung der Nachweis der mit einem Marker versehenen Tiefenhydrophobierung.
Detection of ion ingress by LIBS for Evaluation of the remaining lifetime of a concrete structure
(2018)
The majority of the built infrastructure is made of concrete, which is a multiphase system made of cement, aggregates, water and pores. Concrete is often used in combination with steel as reinforced concrete. Environmental influences, especially the ingress of harmful ions in combination with the ingress of water, trigger different damage processes which reduce the designed lifetime of a structure. The ingress of chlorides from de-icing salt or sea water leads to corrosion of the reinforcement. Also the carbonation of the concrete may trigger the corrosion of the reinforcement. The ingress of alkalis from de-icing salts may cause the expansion of the amorphous silica aggregates (alkali-silica reaction) through formation of a swelling gel of calcium silicate hydrate if water is present. The ingress of sulfates may cause spalling of the concrete surface due to ettringite formation.
For the standard procedure in civil engineering cores are taken, cut in slices, grinded and the obtained homogenized powder is solved in acid and investigated by standard procedures.
BAM has developed the LIBS technique for the 2D evaluation of the chemical composition of concrete [1-11]. The technique is established for automated laboratory use with high numbers of samples to investigate transport processes of harmful species (Cl-, CO2, SO42- and alkalis) in concrete. Information about ingress depth and the quantitative values are important to estimate the remaining lifetime of the infrastructure. LIBS is a surface technique. To get information about the ingress depth, a core has to be taken and cut in the middle. The measurements are carried out at the cross section. The main advantages of LIBS are the direct measurement on the surface of the concrete, fast analysis (sample rate 100 Hz) with a spatial resolution of up to 100 µm, the consideration of the heterogeneity of the concrete and the possibility of automated measurements which save a lot of manpower and time. As an example the investigation of ingress profiles for standard diffusion and migration tests in civil engineering takes hours in comparison to just a few minutes using LIBS. At the same time a 2D-evaluation provides information about hot spots of elemental concentration which may not be found by standard methods.
Ingress of chlorides due to a crack in a repair mortar. Left: Photo of the cross section of a concrete core and the surface investigated by LIBS (area 70 mm x 70 mm). Right: Color coded chlorine intensity on the cross section of a concrete core, dark red represents high chlorine content.
The state of the art of LIBS technique for applications in civil engineering will be presented, including typical results of 2D investigation of concrete in laboratory. The performance is also demonstrated by examples for onsite applications using a mobile LIBS system. The road map to standardization is presented as well.