Filtern
Erscheinungsjahr
Dokumenttyp
- Vortrag (19932) (entfernen)
Sprache
- Deutsch (13122)
- Englisch (6759)
- Mehrsprachig (24)
- Spanisch (13)
- Französisch (9)
- Russisch (3)
- Tschechisch (1)
- Ungarisch (1)
Referierte Publikation
- nein (19932)
Schlagworte
- Korrosion (249)
- Corrosion (138)
- Additive manufacturing (122)
- Additive Manufacturing (121)
- Additive Fertigung (114)
- Concrete (107)
- Hydrogen (102)
- Nanoparticles (93)
- LIBS (92)
- Wasserstoff (82)
Organisationseinheit der BAM
- 8 Zerstörungsfreie Prüfung (921)
- 6 Materialchemie (833)
- 7 Bauwerkssicherheit (819)
- 9 Komponentensicherheit (739)
- 1 Analytische Chemie; Referenzmaterialien (580)
- 5 Werkstofftechnik (457)
- 4 Material und Umwelt (440)
- 3 Gefahrgutumschließungen; Energiespeicher (420)
- 7.6 Korrosion und Korrosionsschutz (351)
- 9.4 Integrität von Schweißverbindungen (350)
Der Vortrag stellt Grundlagen und Anwendungen der industriellen Durchstrahlungsprüfung vor. Ausgehend von den Röntgenfilmen und ihren Eigenschaften werden moderne Technologien zum Filmersatz erläutert. Das sind die Computerradiographie mit Speicherfolien oder digitale Matrixdetektoren (DDA). Zentrale Frage in der industriellen Radiographie ist die erreichbare Bildqualität. Als Anwendungen werden die Korrosionsprüfung von Rohrleitungen mit CR und die Hoch-Kontrastempfindlichkeits-Radiographie mit DDAs präsentiert.
Recent developments of photon counting and energy discriminating detectors for radiographic testing
(2017)
The direct detection of X-ray photons into electrical signals is enabled by usage of highly absorbing photo conducting materials (e.g. CdTe) as detection layer of an underlying CMOS semiconductor X-ray image detector. If the read-out speed is high enough (ca. 50 – 100 ns dead time) single X-ray photons can be counted and their energy measured. Read-out noise and dark image correction can be diminished. By setting energy thresholds, selected energy ranges of the X-ray spectrum can be detected or suppressed. This allows material discrimination or reduction of scattered radiation, which results in an enhanced contrast sensitivity.
Laser powder-based directed energy deposition (DED-L) is a technology that offers the possibility for 3D material deposition over hundreds of layers and has thus the potential for application in additive manufacturing (AM). However, to achieve broad industrial application as AM technology, more data and knowledge about the fabricated materials regarding the achieved properties and their relationship to the manufacturing process and the resulting microstructure is still needed. In this work, we present data regarding the low-cycle fatigue (LCF) behavior of Ti-6Al-4V. The material was fabricated using an optimized DED-L process. It features a low defect population and excellent tensile properties. To assess its LCF behavior two conventionally manufactured variants of the same alloy featuring different microstructures were additionally tested. The strain-controlled LCF tests were carried out in fully reversed mode with 0.3 % to 1.0 % axial strain amplitude from room temperature up to 400°C. The LCF behavior and failure mechanisms are described. For characterization, optical microscopy (OM), scanning electron microscopy (SEM), and micro-computed tomography (µCT) were used. The low defect population allows for a better understanding of the intrinsic material’s properties and enables a fairer comparison against the conventional variants. The fatigue lifetimes of the DED-L material are nearly independent of the test temperature. At elevated test temperatures, they are similar or higher than the lifetimes of the conventional counterparts. At room temperature, they are only surpassed by the lifetimes of one of them. The principal failure mechanism involves multiple crack initiation sites.
This presentation shows some experimental results of the characterization of the creep behavior of LPBF 316L, which has been poorly studied and understood to date. The presentation includes results regarding the mechanical properties, the initial microstructural state and its evolution under loading, and the damage mechanism. This work was done within the BAM focus area materials project AGIL. As a benchmark to assess the material properties of the LPBF 316L, a conventionally manufactured variant was also tested.