Filtern
Dokumenttyp
- Vortrag (62)
- Beitrag zu einem Tagungsband (14)
- Zeitschriftenartikel (11)
- Posterpräsentation (6)
- Sonstiges (1)
Schlagworte
- Fibre break (10)
- Multiscale model (9)
- Composite (8)
- Degradation (8)
- Composite pressure vessels (7)
- Reduced volume method (7)
- Integral range (6)
- Composite pressure vessel (5)
- TAHYA project (5)
- Acceptance rate (4)
Organisationseinheit der BAM
- 3.0 Abteilungsleitung und andere (94) (entfernen)
Eingeladener Vortrag
- nein (62)
Das Einsatzspektrum von den besonders leichten Druckbehältern aus Faserverbund-werkstoffen erweitert sich kontinuierlich. Dies führt dazu, dass mit der erweiterten Verwendung auch die thermisch zulässigen Einsatzgrenzen dieser Behälter ausgeschöpft und sogar teilweise überschritten werden. So können bspw. Atemluftflaschen im Brandeinsatz der Feuerwehr an der Behälteroberfläche derart hohen Umgebungstemperaturen ausgesetzt werden, dass die zulässige Höchsttemperatur von 65 °C deutlich überschritten wird.
Durch experimentelle Temperaturversuche an Typ-III-Atemluftflaschen mit einem Innenbehälter aus Aluminium konnte gezeigt werden, dass bei der Brandbekämpfung die untersuchten Atemluftflaschen lokal über das in der Zulassung abgeprüfte Temperaturspektrum erhitzt werden. Der Glasübergangsbereich des Faserverbundwerkstoffs wird partiell um bis zu 95 °C überschritten. Um die reale Sicherheit der Atemluftflasche bewerten zu können, wurde ein analytisches Hybridbehältermodell entwickelt, das die Beanspruchungen mit validierten Materialtemperaturverläufen berechnet. Mit der Einbindung von Schädigungsansätzen konnte ein bisher nicht hinreichend beachtetes thermisches Degradationsverhalten in den Berechnungen berücksichtigt werden. Zudem wurden insgesamt 90 altersbedingt ausgesonderte Feuerwehr-Atemluftflaschen zerstörend geprüft, um nähere Erkenntnisse über den Sicherheitszustand am Ende der Lebenszeit zu erhalten.
In diesem Kolloquium werden Forschungsergebnisse vorgestellt, die im Rahmen einer Promotionsarbeit die Auswirkungen dieser erhöhten thermischen Betriebslasten auf eine Typ-III-Atemluftflasche mit einem Innenbehälter aus Aluminium darstellen und bewerten.
Defining a reduced volume zone for the simulation of burst test on composite pressure vessels
(2018)
The developed model uses a Monte-Carlo simulation to evaluate the accumulation of fibre breaks on composite structures. As the micromechanical aspects affecting the accumulation process is evaluated within a particular finite element size (0.1 mm x 0.1 mm x 8 mm), the industries would not be able to use the model on a real-size structure. Therefore, the reduced volume method is used to provide the statistical information between the required number of elements and simulations.
The fibre-break model developed at Mines ParisTech has been able to show the effect of pressurisation rate on pressure vessels. This simulation however had to use a smaller model, as the computation time becomes enormous for simulating a real-scale pressure vessel. Reduced volume method then has been studied on different model configuration. The study showed that the method can be used only on certain configurations. It also gives a positive insight to reduce the computation time.
Um ein verlässliches Ergebnis der Monte-Carlo-Simulation zu garantieren, muss die Zuverlässigkeit des Tools vor dessen Anwendung sorgfältig geprüft werden. In diesem Vortrag werden die Validierung der angenommenen Verteilungsfunktionen, die Vertrauensbereiche und die Grenzwerte der generierten Grundgesamtheit vorgestellt. Darauf aufbauend wird der Ablauf der gesamten Simulation von der Erzeugung der Zufall-Variablen bis hin zur Akzeptanzrate gezeigt.
Due to high specific stiffness, fibre reinforced plastics are the dominant material group for the design of mobile pressure vessels. At the Federal Institute of Materials Research and Testing (BAM) aging process of composite pressure vessels is studied to be able to give more accurate lifetime predictions in future. Investigations are based on type III breathing air cylinders consisting of an aluminium tank which is fully wrapped with carbon fibre reinforced plastics. Goal is to detect changes of residual stresses over life time which directly affect fatigue strength. Within this paper an approach is presented to monitor residual stresses via an experimental modal analysis (EMA). First, the influence of changed stress conditions on modal parameters is analysed via a numerical study. Secondly, a test bench for an EMA is set up. To be able to analyse cylinders of different prestress condition, several specimens are prestress modified via high-temperature and high-pressure treatment. During modification processes, specimens are monitored via optical fibres to control prestress modifications. Through experimental measurements of the modified specimens via EMA changes in prestressing can be detected. Finally, validity and accuracy of the EMA is evaluated critically by comparing all numerically and experimentally obtained data.
The developed model has certain limitations of the element size to be used in the simulation to characterise the strength of composite materials. A reduced volume method is proposed in order to reduce the number of degree of freedom of the finite element simulation.This study has revealed certain configuration to be followed to speed up the computation time.
Fibre-reinforced plastics (FRP) especially carbon-fibre-reinforced polymer (CFRP) and glass-fibre-reinforced polymer (GFRP) are commonly used materials in high pressure vessels and storage units for automotive and aerospace purposes. Optical fibres are suitable to be integrated or directly applied to the surface of FRP components. Using optical fibres it is possible to monitor the distributed strain profiles and changes within the fatigue life of a pressure vessel to ensure the operational safety. Within artificial ageing experiments we used swept wavelength interferometry (SWI) based distributed strain sensing for the monitoring of commercial high-pressure composite cylinder. This artificial ageing was performed using test conditions of 503bar pressure load (service pressure 300 bar) and 89 °C for 100 h. The polyimide coated optical fibres were glued to the surface externally in circumferential and axial direction. Using distributed strain sensing (DSS) material expansion of over 0.5% were monitored with sub-centimetre spatial resolution. Within the circumferential direction we observed up to 10 % local fluctuation compared to the median strain caused by inhomogeneous material expansion, which could cause local material fatigue. In addition, we determined material degradation manifested itself as localized remaining material expansion and/or contraction. Results have been validated by other non-destructive methods like digital strip projection.