Filtern
Dokumenttyp
Sprache
- Englisch (12)
Schlagworte
- Photodegradation (12) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (3)
In the aquatic environment, pharmaceutical drugs are submitted to degradation processes, where pho-todegradation is one of the most important mechanisms affecting the fate, persistence and toxicity of thecompounds. Carbamazepine, a widely used antiepileptic, is known to suffer photodegradation in waterbodies and generate photoproducts, some of them with higher potential toxicity than the parent com-pound. Therefore, to evaluate the toxic effects of CBZ when combined with its photoproducts, an acuteexposure (96 h) with the edible clam Scrobicularia plana was performed using environmental concentra-tions of CBZ (0.00–9.00 µg/L) irradiated (and non-irradiated) with simulated solar radiation. The analysisof the irradiated CBZ solutions by mass spectrometry revealed the formation of 5 photoproducts, includ-ing acridine (a compound known to be carcinogenic). Oxidative stress results showed that the exposureto CBZ photoproducts did not increase the toxicity to clams, by comparison with the parent compound.
Outdoor exposure tests are a common tool to evaluate the weathering resistance of a polymeric material or component. However, they have only a limited validity, mainly due to the limited reproducibility of the weather as well as of the bad adaptability to other exposure sites. Typically, an outdoor exposure is characterized by the measured radiant exposure; sometimes averaged temperature data are added. These can be – separately – related to long-term annual means, to get an idea on the severity of the exposure.
However, as for polymeric ageing, irradiance and temperature act simultaneously, such severity of an outdoor exposure could be better described by a computed property change of a similar material, which is calculated from the hourly irradiance and temperature values on the base of established exposure response functions.
In this way, various outdoor exposures are evaluated. For several exposure sites, annual deviations of the ageing amount are related to annual mean values, to evaluate the weathering reproducibility at the exposure site. Additionally, correlations to relevant weather parameters are illuminated. Also some specific exposure conditions, such as tilt angle, are tested. Compared to the use of weathering reference materials, this procedure unfavourably depends on the availability of a suited control as well as on the quality of the established exposure response function. In contrast, it enables a later exposure evaluation, on the base of documented weather data, if for instance no reference material was exposed.
Outdoor exposure tests are a common tool to evaluate the weathering resistance of a polymeric material or component. However, they have only a limited validity, mainly due to the limited reproducibility of the weather as well as of the bad adaptability to other exposure sites. Typically, an outdoor exposure is characterized by the measured radiant exposure; sometimes averaged temperature data are added. These can be – separately – related to long-term annual means, to get an idea on the severity of the exposure.
However, as for polymeric ageing, irradiance and temperature act simultaneously, such severity of an outdoor exposure could be better described by a computed property change of a similar material, which is calculated from the hourly irradiance and temperature values on the base of established exposure response functions.
In this way, various outdoor exposures are evaluated. For several exposure sites, annual deviations of the ageing amount are related to annual mean values, to evaluate the weathering reproducibility at the exposure site. Additionally, correlations to relevant weather parameters are illuminated. Also some specific exposure conditions, such as tilt angle, are tested.
Compared to the use of weathering reference materials, this procedure unfavourably depends on the availability of a suited control as well as on the quality of the established exposure response function. In contrast, it enables a later exposure evaluation, on the base of documented weather data, if for instance no reference material was exposed.
Phototransformation of the “emerging” BFR 1,3,5-Tris-(2,3-dibromopropyl)-1,3,5-triazine-2,4,6-trione
(2017)
The occurrence and fate of brominated flame retardants (BFRs) in the environment are topics of increasing concern. In recent years, numerous studies about their global transport, UV degradation, bioaccumulation and toxicity were performed to assess their environmental fate. As a result, most of the first generation BFRs are banned or restricted, and replaced by new ones. However, based on similar properties these new compounds may also pose a serious risk by causing adverse effects to human health and the environment. According to the European Food Safety Authority (EFSA) the class of the “emerging” BFRs are defined as compounds that have been identified in any environmental compartments, but the potential for degradation or bioaccumulation of these emerging BFRs is partially unknown.
A representative of this class of compounds is the heterocyclic TDBP-TAZTO which was first detected in mollusks from Chinese bohai sea and in environmental matrices near a manufacturing plant in southern china. Furthermore, Wang et al. describe that the growth of the alga Nannochloropsis sp. is inhibited by TDBP-TAZTO in a concentration dependent manner but the photo-chemical behavior as well as the formation of possible photo-transformation products (PTPs) are still unknown. In order to clarify this complex issue photo-degradation experiments were by determining the rate constants and degradation half-life times of TDBP-TAZTO in different solvent compositions. In this study, the photodegradation of TDBP-TAZTO was performed for the first time to identify its photolysis products and to get a first understanding about the main degradation pathway in environmental matrices.
Photodegradation of the „novel“ brominated flame retardant tris-(2,4,6-tribromophenoxy)-s-triazine
(2016)
Brominated flame retardants (BFRs) comprise a class of structurally diverse compounds that are functionally related and used in materials to reduce the flammability of polymers. Due to their global distribution, potential persistence, bioaccumulation and toxicity most of the BFRs of the first Generation are banned or restricted, and replaced by new ones. However, based on similar properties these new compounds may also pose a serious risk by causing adverse effects to human health and the environment.
These alternative BFRs were grouped into two classes: „novel” and „emerging” BFRs. Emerging BFRs are defined as compounds that have been identified in any environmental compartments whereas novel BFRs are only detected in materials and/or goods above 0.1 wt.-%.
The environmental fate of these alternative BFRs is partially unknown. Over the past years a multitude of studies on the photodegradation of BFRs in environmental matrices have been conducted to assess the photochemical behavior and fate in the environment. The photolytic debromination reaction is particularly induced among BFRs by UV exposure.
The novel brominated triazine-based flame retardant tris-(2,4,6-tribromophenoxy)-s-triazine (TTBPTAZ) (Table 1) is a BFR that is mainly used in acrylonitrile butadiene styrene and high impact polystyrene.
Ballesteros-Gómez et al. detected TTBP-TAZ in 8 of 13 plastic parts of consumer products and in 9 of 17 indoor dust samples but the photochemical behavior and fate is not known until now.
The results of the present study, focused on photodegradation processes were performed for the first time for TTBP-TAZ to identify the photolysis intermediates and products to assess the environmental fate.
The identification of transformation products (TPs) of pesticides in food is a crucial task difficult to tackle, due to the lack of standards. In this work, we present a novel methodology to synthesize five main TP standards of the insecticide chlorpyrifos (CPF) and to investigate their occurrence in selected fruits and spices. TPs were electrochemically (EC) synthesized using a boron-doped diamond electrode (BDD) and identified by EC coupled online to mass spectrometry, LC-MS/MS, and high-resolution mass spectrometry. CPF and its TPs were analyzed in the food samples by LC-MS/MS on multiple reaction monitoring (MRM) after dispersive solid-phase extraction. A good recovery of 83–103% for CPF and 65–85% for TPs was obtained. Matrix effects, which cause signal suppression, ranged between 81 to 95% for all targeted analytes. The limit of detection and quantification for CPF were 1.6–1.9 and 4.9–5.7 μg/kg, respectively. Among investigated samples, CPF was determined in fresh lemon (104 μg/kg), fenugreek seed (40 μg/kg), and black pepper (31 μg/kg). CPF content in all samples was lower than the EU maximum residue level (MRL). The most frequently detected TPs were diethylthiophosphate and diethylphosphate. Other TPs, CPF oxon and trichloropyridinol, were also detected. Hence, EC is a versatile tool to synthesize TP standards which enables the determination of contaminants and residues in foodstuffs even if no commercial standards are available.
Nowadays, electrochemistry coupled online to mass spectrometry (EC-MS) or to liquid chromatography-mass spectrometry (EC-LC-MS) is a technique of interest to investigate metabolic transformation of xenobiotics in living organisms. It enables the production of redox products in an electrochemical cell, the separation by an analytical column and the detection by mass spectrometry online. Furthermore, EC-LC-MS enables to determine short lived transformation products (TPs) and their bioconjugates in a fully automated way. Although the EC-MS selectivity is incomparable to enzymatic reactions, it is advantageous by reducing analysis time and matrix complexity compared to cytochrome based metabolism. However, in the development of EC-MS, most efforts are devoted for prediction of drug metabolism in the human body and there is very limited work on agrochemicals in general.
The main objective of this work was to develop an online EC-LC-MS method that could predict the metabolism of fluopyram (fungicide) and chlorpyrifos (insecticide). Oxidation products were produced by using a boron doped diamond electrode and characterized by either online LC-MS or offline LC-MS/MS. After incubation with rat and human liver microsomes, different targeted and suspected metabolites were identified by LC-MS/MS and high resolution-mass spectrometry (HR-MS) and compared with the EC based methods. Additionally, conjugation reactions with a variety of biomolecules such as glucoside and glutathione were investigated by trapping the oxidized species before entering to mass spectrometry.
In summary, phase-I metabolism by N-dealkylation, O-dealkylation, P-oxidation, hydroxylation and dearylation and phase-II metabolism by conjugation with glutathione mechanisms were successfully mimicked by EC-LC-MS. Fluopyram is primarily metabolized to 7- and 8-mono- hydroxyl, 7,8-di-hydroxyl and 2-trifluoromethyl benzamide, and chlorpyrifos is metabolized to chlorpyrifos oxon, trichloropyridinol, diethylthiophosphate and diethylphosphate.
Identifying the fate of agrochemicals is important to understand their potential risk for living organisms. We report here new photodegradation products (PPs) of the fungicide fluopyram. The PPs were produced by irradiating a fluopyram standard in 0.1% acetonitrile aqueous media by a 150-W medium pressure Hg-lamp that emits wavelengths between 200–280 nm. The structural elucidation of PPs was achieved by combining the retention time, isotopic pattern, targeted fragmentation, and accurate mass measurements using liquid chromatography-tandem mass spectrometry (LC-MS/MS) and high resolution-MS (HRMS). In addition to previously known PPs, seven new PPs of fluopyram were identified in this work: mainly dihydroxyl and hydroxylimide fluopyram as well as mono, di, and trihydroxyl lactam. Additionally, two PPs were found to be formed by rearrangement after the loss of H2C=CH2. Hence, the results of the work contribute to extending the current knowledge regarding the photoinduced fate of agrochemicals, and fluopyram in particular.
Cost-effective water cleaning approaches using improved Treatment technologies, for instance based on catalytic processes with high activity catalysts, are urgently needed. The aim of our study was to synthesize efficient Fenton-like photo-catalysts for rapid degradation of persistent organic micropollutants in aqueous medium. Iron-based nanomaterials were chemically synthesized through simple procedures by immobilization of either iron(II) oxalate (FeO) or iron(III) citrate (FeC) on magnetite (M) nanoparticles stabilized with polyethylene glycol (PEG). Various investigation techniques were performed in order to characterize the freshly prepared catalysts. By applying advanced oxidation processes, the effect of catalyst dosage, hydrogen peroxide concentration and UV-A light exposure were examined for Bisphenol A (BPA) conversion, at laboratory scale, in mild conditions. The obtained results revealed that BPA degradation was rapidly enhanced in the presence of low-concentration H2O2, as well as under UV-A light, and is highly dependent on the surface characteristics of the catalyst. Complete photo-degradation of BPA was achieved over the M/PEG/FeO catalyst in less than 15 minutes. Based on the catalytic performance, a hierarchy of the tested catalysts was established: M/PEG/FeO > M/PEG/FeC > M/PEG. The results of cytotoxicity assay using MCF-7 cells indicated that the aqueous samples after treatment are less cytotoxic.
The preparation of porphyrins and phthalocyanines covalently attached onto nanostructured magnetic supports consisting of magnetite nanoparticles coated with an amorphous silica shell is reported. The easy recovery of these heterogeneous photocatalysts, just by applying an external magnetic field, allows their reuse in multiple treatment cycles. The photocatalytic activity of the non-immobilized photosensitizers and the obtained hybrid materials was evaluated in the degradation of 17 beta-estradiol, as a model organic pollutant present in water, using batch and flow mode treatment systems, assisted by visible light radiation (4 mW cm(-2)). The flow mode system potentiated the photocatalytic capacity of these novel hybrid materials. In order to improve the process, further studies based on different photocatalyst concentration and pH conditions were performed. Reuse capacity of these materials was investigated upon three photocatalytic cycles.