Filtern
Dokumenttyp
- Zeitschriftenartikel (3) (entfernen)
Sprache
- Deutsch (1)
- Englisch (1)
- Französisch (1)
Referierte Publikation
- nein (3)
Schlagworte
- Thin film coatings (3) (entfernen)
The dilution of biogenic fuels into lubricating engine oils often leads to a shortening of the recommended oil drains (between 30% and 60%) and an increase in wear. The large number of overlapping and influencing factors, of which dilution and polymerization of fuel components in the engine oil are emphasised, makes it difficult to find a uniform solution to prevent failures in the various applications.
Insofar single solutions for the different types of biofuels are needed. The contribution of base oil chemistry and additives as well as triboactive materials is featured to deal with the adverse effects of biofuels. In the frame of the European Commission (EC)-funded project 'cleanengine', tentative engine oils based on esters with a content of renewables and polyglycols are formulated to increase the lubricant's tolerance in engines fuelled with biofuel-based blends, with the aim of ensuring required lubricating and wear protection performance while keeping oil drain intervals unchanged.
The present paper focuses on four-stroke diesel applications, fuelled by biodiesel (fatty acid methyl ester — FAME) as well as by rapeseed oil and Jatropha oil (pure vegetable oils, triglycerides), together with relevant blends of those biofuels and conventional diesel fuel.
This paper screens the functional profile (in particular rheological, toxicological, bio-compatibility, tribological and biofuels affinity) of lube families with respect to biofuel contamination. Moreover, this is followed by the contributions of piston ring and liner materials as well as thin film coatings.
Le secteur automobile doit faire face actuellement à de nouveaux challenges au niveau de la construction allégée, des économies de carburant et des coûts. Ces exigences motivent la mise au point de tribosystèmes pouvant résister à des pressions de contact de plus en plus élevées avec de faibles coefficients de frottement. L'optimisation de systèmes existants par l'application de revêtements de surface performants représente une alternative intéressante. Ce texte présente les performances de couches minces dans des conditions d'essais de slip-rolling (roulement à composante de glissement) en présence de lubrifiants liquides. Après une première sélection à température ambiante, les revêtements les plus performants ont été testés à 120 °C. Il s'agit de revêtements DLC en carbone hydrogéné (a-C:H) et en carbone tétraédrique (ta-C) de dernières générations ainsi qu'un nouveau système « revêtement/substrat ». Certains des revêtements DLC développés récemment sont résistants en slip-rolling au moins jusq'à 10 millions de cycles à 120 °C dans l'huile moteur sous des pressions hertziennes de contact de P0max = 2600 / 2940 MPa. De plus, le nouveau système revêtement Zr(C,N)x/substrat peut résister au moins à 1 million de cycles sous des pressions hertziennes initiales de contact allant jusqu'à P0max = 3500 MPa et à des températures de lubrifiant d'au moins 120 °C. -----------------------------------------------------------------------------------------------------------------------------------------------
The light-weight approach and fuel economy targets in today's automotive engineering require tribosystems, which can withstand higher contact pressures associated with low coefficients of friction. The application of surface coatings represents one approach among others. This paper presents thin film coatings performances in a bench mark test procedure exerting slip-rolling conditions in the presence of liquid lubricants. After a first selection at room temperature, the most resistant coatings were evaluated at 120 °C. These are newly developed DLC coatings (a-C:H & ta-C) as well as a novel coating-substrate system. Some of the newly developed DLC-coatings are slip-rolling resistant for at least up to 10 million cycles at 120 °C oil temperature) under Hertzian contact pressures of P0max = 2600 / 2940 MPa. Furthermore, this novel Zr-based thin film coating can withstand at least 1 million cycles under initial Hertzian contact pressures of up to P0max = 3500 MPa and oil temperatures of at least 120 °C associated with low coefficients of friction under mixed/boundary conditions.