Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (9)
- Beitrag zu einem Sammelband (8)
- Vortrag (2)
Sprache
- Englisch (19)
Schlagworte
- Superalloys (19) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (2)
Time dependence of y/y' Lattice Mismatch in Creep-deformed Single Crystal Superalloy SC16 at 1173 K
(2007)
The formation of pores in CMSX-4 nickel based superalloys is detrimental to the service life of the material. A way to avoid the problem is to treat the superalloys under Hot Isostatic Pressing (HIP), which enables a large volume fraction of pores to be annihilated. This paper aims to understand the contribution of plastic activity related to the gliding of dislocations on the pore annihilation. Simulations based on a phase-field model of dislocation are performed and make it possible to consider the strong anisotropy of the CMSX-4 under HIP conditions in conjunction to the strong elastic heterogeneity introduced by the pore. For pores with a radius of few micrometers, it is shown that edge parts of dislocation lines that present an extra half atomic plane oriented towards the pore are stacked above and under it in the direction which is perpendicular to their slip-planes, causing an increase of the number of dislocation along the four octahedral directions of the FCC single crystal which intersect the pore center. Results are streamlined within the isotropic elastic theory of dislocations. Effects of elastic anisotropy and dislocation reactions are also investigated in order to specify what would be the dislocation configuration around a pore in CMSX-4 under HIP conditions. Notably, the elastic anisotropy is shown to significantly modify the arrangement of dislocations close to the pore equator. Simulations also allow for the characterization of pore/dislocation interactions when dislocations are involved in Low Angle Boundaries as experimentally observed.
Inconel 718 was spin coated twice and fourfold with a sol to obtain 200- and 400-nm-thick transition alumina films on the surface. Bare and solgel alumina-coated Inconel 718 samples were exposed to NaCl solution to study their corrosion behavior by means of electrochemical impedance spectroscopy. In combination with scanning electron microscopy, it was shown that bare Inconel 718 is after initial passivation prone to pitting corrosion. For the coated Inconel 718 samples, an improvement in the protective effect of the coatings with time was observed. This observation is in contradiction to the results of other authors who observed degradation of alumina coatings exposed to NaCl solution with time. Transmission electron microscopy revealed a formation of (1) a compacted region at the coating surface as well as (2) a chromium-rich region at the interface between coating and alloy during the contact with a NaCl solution. The last one mainly contributes to the observed chronological sequence of electrochemical characteristics of the samples.
The discovery of the high entropy concept at the beginning of the 3rd millennium lead to a worldwide increase in metallurgical research, as the possible element combinations seemed nearly endless and the range of applications wide. In the early years of research, one of the main goals was the discovery of a single-phase high entropy alloy. As research evolved, it was found that properties could be enhanced by opening the HE-concept towards multiphase alloys, and from the wide area of possibilities our group chose a tuning of the properties towards high temperature application.
Compositionally complex Al10Co25Cr8Fe15Ni36Ti6 alloy, which is single-phase at high temperature, around 1200°C, shows a three phase morphology at intermediate temperatures, around 800°C. A high temperature homogenization procedure has to be applied in order to decrease the segregation induced by the dendritic growth. Subsequent annealing promotes the formation of the strengthening γ' precipitates. The alloy shows a positive lattice misfit between the γ and the γ' phase, which can be an indicator for good creep properties.
The microstructure can be optimized by adding trace elements such as Mo and Hf, known as γ and γ' strengtheners in Ni-based superalloys, respectively. Atom probe measurements show that Mo segregates into the γ matrix, and Hf prefers the γ' precipitates, where it increases the lattice parameter and thus also the lattice misfit, by about 50%. The alloy family shows interesting mechanical properties, especially the Al9.5Co25Cr8Fe15Ni36Ti6Hf0,5 alloy – its tensile properties are better than those of commercial Alloy 800H and IN617 at temperatures up to 700°C.
α(1 0 0) Dislocations are observed in nickel-base superalloys after creep deformation at high temperatures and low stresses. They are formed in the γ/γ´ interfaces by a three step mechanism. First, primary dislocations with Burgers vector α/2(1 0 1) and 60° character are left behind in the interfaces when dislocation loops glide through the γ channels. The 60° dislocations move into edge orientation and react forming secondary dislocations α/2(1 1 0). In the third step, new primary dislocations are knit into the already existing meshes of primary and secondary dislocations, which results in hexagonal misfit dislocation networks consisting of secondary dislocations α/2(1 1 0) and tertiary dislocations α(1 0 0), both of edge type. This self-organisation process is explained by dislocation theory and crystallography.
Creep deformation accelerates when the α(1 0 0) interfacial dislocations enter the γ´ phase. During their climb towards the opposite interface, they attain a characteristic rectangular shape. This shape and the importance of the α(1 0 0) super dislocations for creep deformation are discussed.
An extension of the constitutive viscoplastic model of Meric and Cailletaud is presented. The new model
accounts for coupling of plasticity and viscoplasticity to describe the rate dependence at low and moderate
temperatures. The model contains two boundaries: an elastic one and a viscoplastic one. Between the
boundaries, the only contribution to yielding is the rate dependent viscoplastic mechanism. Once the viscoplastic
boundary is reached, an additional rate independent flow mechanism becomes active. However, the extended
model is not able to predict properly both creep and long-term relaxation tests simultaneously. Therefore, a
deformation-induced softening is assumed, which is supposed to mainly affect static recovery.
The model has been calibrated with the mechanical tests on a single crystal nickel-basis superalloy. The uniaxial
tests have been carried out in the temperature interval 600°C – 1100°C in [001], [011] and [111] specimens.
The predicted creep, relaxation and non-isothermal cyclic tests exhibit reasonable agreement with the
experimental observations.
Experimental characterization and mechanical modeling of creep induced rafting in superalloys
(2012)
A constitutive model has been developed for the high temperature mechanical behavior of single crystal superalloys, including rafting and its consequences. The flow stress depends on the γ channel width via the Orowan stress. An evolution equation for channel widening during high temperature straining has been derived and calibrated with measurements. Therein, rafting is assumed to be driven by the relaxation of internal stresses. The model is able to represent the mechanical softening at high stresses consecutive to rafting. The model has been applied to simulate rafting during uniaxial creep in several crystal orientations, in notched specimens as well as in cyclically loaded specimens.