Filtern
Dokumenttyp
- Beitrag zu einem Tagungsband (4)
- Zeitschriftenartikel (3)
- Vortrag (1)
Schlagworte
- Dynamic loads (8) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (1)
Wind turbines on offshore sites (OWECs) are subjected to combined loads from wind and waves. These dynamic loads, with a frequency content within the range of the natural frequencies of the structures, cause fatigue-effective stresses in the substructures of wind turbines. Therefore, the examination of natural frequencies is an important part within the design process of wind turbines. The quality of the numerical models for such calculations is of great importance, since the certification guidelines permit only small uncertainties in modal analysis results. The accuracy of the parameters of the numerical model can only be achieved through a comparison of simulation results with corresponding test results. Therefore, it is necessary to measure the dynamic behaviour of all components of the wind turbines simultaneously. This is true not only for the design verification, but also for monitoring the OWECs in operation. The potential of integrated systems for monitoring-based maintenance optimisation should thus be used.
Whenever geosynthetics are used to reinforce or stabilise infrastructural elements such as road- and railways, bridge abutments, run- and taxiways on airports or to protect coastlines of canals and other steep slopes they may be exposed to cyclic loads. Therefore, a reduction factor for dynamic effects on the geosynthetic tensile strength has been included into the calculation of the Long Term Design Strength (LTDS). An approach to assess the behaviour of geosynthetics is to adopt Woehler- or Smith graphs and Haigh-diagrams for polymers. This is because an endurance limit for polymers, which defines an infinite life under a defined cyclic load, has not been seen so far. A huge amount of mechanical testing is needed to predict the behaviour of geosynthetics against this particular background.
To reduce these efforts while getting an indication of the cyclic effect on geosynthetics, a combined method of mechanical and chemical analysis has been developed. The pure tensile strength tests to determine the residual strength after cyclic stress has been amended by IR-spectroscopy and Differential Scanning Calorimetry (DSC). In this context the chain change model of PET has been proven as valid for cyclic loads as well, which helps to define the endurance limit of materials made out of PET. For polyolefins such as PP and PE, a limit for the maximum alternating load has been identified at the point of the stress strain graph where the actual and the numerical stress of a material diverge from each other. Cyclic tensile strength tests have been carried out in a hydraulic test frame. The test parameters have been set to simulate the service life of a railway bed trafficked by high speed trains (ICE).
A material testing program to characterize the concrete behavior under static and dynamic loads
(2010)
In this paper a comprehensive material testing program is described to characterize a German final repository concrete material (BERB1) subjected to static and dynamic loads. The BERB1 material was developed und specified by the German Bundesanstalt für Materialforschung und -prüfung (BAM) for targets used for drop tests according to the KONRAD requirements.
The testing consists of three concurrent laboratory experimental programs performed in the USA. An extensive preliminary testing program in Germany was performed to assure the required concrete specifications during fabrication and curing.
The first set of data is the static basic material test program consisting of structural tests to quantify macroscopic concrete properties under quasi-static loads. Cubic and cylindrical specimens are investigated under this effort. The second set of test data is from the static complete material test program, where cylindrical concrete specimens are subjected to a variety of quasi-static axial and radial stress and strain paths using a high-pressure hydraulic tri-axial chamber. The material is characterized for confining pressures up to 400 MPa. The third set of data is from the dynamic complete material test program, which uses a modified Split-Hopkinson Pressure Bar to induce dynamic compression and tension waves into cylindrical concrete specimens that generate strain-rates up to 400 s-1.
The ensemble of data generated in these experiments provides a complete set of data that effectively describes the behavior of this concrete and can be used to develop a constitutive calculation model. In addition, the results of the tests show a significant effect of moisture on the strength and rheology of this concrete for quasi-static pressures greater than 50 MPa. Numerical drop test simulations with the developed constitutive model in the Lagrangian finite element code, LS-DYNA, show good agreement with the experimental results from a BAM research project.
Scaled-down experimental facility: Can reproduce actual failures; can produce simulated data for identifying cracks in the substructure or other defects. The acceleration data can be converted into an equivalent deformation. The experimental facility can analyse dynamic loads. Equivalent force data: Facilitates the application to a health monitoring system; simplifies the development of predictive maintenance. These data is helpful in validating analytical or simulation models.
This paper presents a method for processing acceleration data registered on a train and determining the health condition of a subway’s substructure. The acceleration data was converted into a dynamic deformation by applying a transfer function defined using the Empirical Mode Decomposition Method.
The transfer function was constructed using data produced on an experimental rig, and it was scaled to an existing subway system. The equivalent deformation improved the analysis of the dynamic loads that affect the substructure of the subway tracks because it is considered the primary load that acts on the track and substructure. The acceleration data and the estimated deformations were analyzed with the Continues Wavelet Transform. The equivalent deformation data facilitated the application of a health monitoring system and simplified the development of predictive maintenance programs for the subway or railroad operators. This method better identified cracks in the substructure than using the acceleration data.
Ground vibrations near railway lines are generated by the forces that are acting between wheel and rail. It seems to be a straight forward assumption that the vehicle dynamics are important for the level and the frequencies of the excitation forces. Different vehicle dynamics phenomena are analysed for their role in the excitation of ground vibrations: rigid body modes of the bogies, elastic (bending) modes of the car body, and elastic modes of the wheelset. The theoretical analyses use rigid body models, simplified elastic models, and detailed elastic models. Some of these problems are vehicle–track interaction problems where 3D finite‑element boundary‑element models have been used for the track and soil. It is shown that the rigid or flexible vehicle modes are well in the frequency range of ground vibrations (4 to 100 Hz). They have an influence on the excitation force but the additional forces are rather small and can be neglected in ground vibration prediction. The theoretical results are checked by experimental results of a simultaneous measurement of vehicle,
track, and ground vibrations.