Filtern
Dokumenttyp
- Vortrag (4)
- Zeitschriftenartikel (2)
- Beitrag zu einem Tagungsband (1)
- Posterpräsentation (1)
Schlagworte
- Construction and demolition waste (8) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (4)
Responsible treatment of the environment and resources is a key element of sustainability. The building and construction industry is one of the largest consumers of natural resources. Consequently, there is a particular need for regulations and technologies that help to create closed material cycles. From the technological point of view, such efforts are complicated by the growing material diversity and the amount of composites contained in present and future construction and demolition waste (CDW). Nowadays, simple but proven techniques like manual sorting are mainly used. However, this practice not only poses health risks and dangers to the staff performing the work, but also relies on merely obvious, visually striking differences. Automated, sensor-based sorting of these building materials could complement or replace this practice to improve processing speed, recycling rates, sorting quality, and prevailing health conditions. The preliminary results for the identification of a wide variety of building materials with LIBS are presented.
Half of the global material consumption is mineral material. The circularity is still low so that enhanced use of secondary building material is required to close loops. Three different secondary building materials are discussed based on exemplary research results: construction and demolition waste (C&D waste), soil-like material and incineration bottom ash (IBA). Focus was laid on the environmental compatibility of the materials examined mainly by standardized leaching tests. C&D waste was investigated after a wet treatment using a jigging machine, soil-like material and IBA were characterized with respect to their material composition. The environmental compatibility in particular was studied using standard leaching tests (batch tests and column tests). It was concluded that soil-like material can mostly be utilized even when the precautionary limit values set are exceeded by a factor of less than 2. For C&D waste the fine fraction below 2 mm and the content of brick material is problematic. IBA fulfills quality level HMVA-2 following German regulation. Higher quality levels of utilization might be achievable with better treatment technologies.
The pore structure of lightweight granules made from masonry rubble was studied in order to better understand their engineering properties. Thermally and hydrothermally hardened granules were tested. Analysis by ESEM, mercury porosimetry and sorption methods yield important insight into their microstructure. The thermal granules are characterised by partly melted vitreous areas and large internal macropores that are connected via narrow throats. They show a marginal specific surface area along with a hydrophobic behaviour. In contrast, the hydrothermal granules have an accessible mesoporous system containing plate-like and ink-bottle pores. The shape of their water isotherms depending on the granules CaO content is sensitive to the morphology of calcium silicate hydrate phases (CSH). The hysteresis changes from a narrow loop that closes at low pressures, which can be attributed to coarser more crystalline CSH, to a large triangular-shaped loop along with a low pressure hysteresis, which is characteristic for fine fibre-like CSH with ink-bottle and plate-like pore morphologies. Granules with fibre-like CSH have the higher specific surfaces areas but those with more crystalline CSH show stronger physisorption of water molecules.
Most lightweight aggregates (LWA) are produced by thermal Treatment of natural raw materials such as clay and shale. In addition to the high energy costs thereby incurred, the availability of suitable raw materials is limited. Other LWA manufactured from industrial by-products and wastes do not always meet the quality criteria for use in high-Quality lightweight concrete. A real alternative is the use of novel lightweight aggregates (referred to as LWA, aggregates and granules) made from mineral construction and demolition waste. An appropriate manufacturing technology has recently been developed in the framework of a German research project /1, 2/. Masonry rubble of variable grain size containing different amounts of brick material (25 to 70 %) serves as raw material. The LWA are obtained in a multistage manufacturing process by a thermal or hydrothermal treatment, which causes the expansion and the hardening of the material. The novel LWA meet the acceptance criteria for conventional lightweight aggregates. They are suitable for the production of lightweight concrete /2-6/. However to create tailor-made LWA from masonry rubble, the novel expanded materials and the influence of manufacturing conditions have to be understood in more detail. This paper reports on ongoing investigations of the chemico-mineralogical composition and microstructure of the novel LWA and focuses on the results of Chemical analyses, XRD, ESEM, TG/DTA and fusibility tests.
Lightweigt concrete with recycling aggregates made from masonry rubble and rubble-clay mixtures
(2018)
Structural lightweight concrete is a construction material composed primarily of lightweight aggregates (LWA), cement and water. Most LWA are produced by thermal treatment of natural raw materials such as clay and shale today. In addition to the high energy costs thereby incurred, the availability of suitable raw materials is limited. An alternative is the use of recycling LWA made from Mineral construction and demolition waste. Recycling LWA made from masonry rubble and rubble-clay mixtures were studied in two different research projects. The technology pursues the idea of feedstock recycling, which means the recycling is based on the chemical and mineralogical composition of the masonry rubble and clay. The recycling LWA are produced in a multistage manufacturing process by thermal hardening in laboratory and pilot scale. Their particle bulk densities and particle strengths vary between 600 and 2000 kg/m³ and 1.5 and 13 MPa, respectively. Their equivalence to traditional LWA was proven in comprehensive tests of the aggregates themselves as well as the mortars and concretes made therefrom. Our contribution reports on the results of the characterization of the recycling aggregates compared to expanded clays and the studies on LWA concretes.
LIBS‐ConSort: Development of a sensor‐based sorting method for construction and demolition waste
(2023)
AbstractA joint project of partners from industry and research institutions approaches the challenge of construction and demolition waste (CDW) sorting by investigating and testing the combination of laser‐induced breakdown spectroscopy (LIBS) with near‐infrared (NIR) spectroscopy and visual imaging. Joint processing of information (data fusion) is expected to significantly improve the sorting quality of various materials like concrete, main masonry building materials, organic components, etc., and may enable the detection and separation of impurities such as SO3‐cotaining building materials (gypsum, aerated concrete, etc.)Focusing on Berlin as an example, the entire value chain will be analyzed to minimize economic / technological barriers and obstacles at the cluster level and to sustainably increase recovery and recycling rates.The objective of this paper is to present current progress and results of the test stand development combining LIBS with NIR spectroscopy and visual imaging. In the future, this laboratory prototype will serve as a fully automated measurement setup to allow real‐time classification of CDW on a conveyor belt.
Closed material cycles and unmixed material fractions are required to achieve high recovery and recycling rates in the building industry. The growing diversity of construction and demolition waste is leading to increasing difficulties in separating the individual materials. Manual sorting involves many risks and dangers for the executing staff and is merely based on obvious, visually detectable differences for separation. An automated, sensor-based sorting of these building materials could complement or replace this practice to improve processing speed, recycling rates, sorting quality, and prevailing health conditions.
A joint project of partners from industry and research institutions approaches this task by investigating and testing the combination of laser-induced breakdown spectroscopy (LIBS) and visual (VIS)/ near-infrared (NIR) spectroscopy. Joint processing of information (data fusion) is expected to significantly improve the sorting quality of various materials like concrete, main masonry building materials, organic components, etc., and may enable the detection and separation of impurities such as SO3-containing building materials (gypsum, aerated concrete, etc.). Focusing on Berlin as an example, the entire value chain will be analyzed to minimize economic/technological barriers and obstacles at the cluster level and to sustainably increase recovery and recycling rates.
First LIBS measurements show promising results in distinguishing various material types. A meaningful validation shall be achieved with further practical samples. Future works will investigate the combination of LIBS and VIS/NIR spectroscopy in a fully automated measurement setup with conveyor belt speeds of 3 m/s.
Beim Recycling von Bau- und Abbruchabfällen werden bisher bevorzugt einfache, aber bewährte Techniken eingesetzt, um große Mengen an Bauschutt in kurzer Zeit zu verarbeiten. Dies steht im Gegensatz zu den immer komplexer werdenden Verbundwerkstoffen und Strukturen in der Mineralbaustoffindustrie. Die manuelle Sortierung birgt viele Risiken und Gefahren für das ausführende Personal und basiert lediglich auf offensichtlichen, visuell erkennbaren Unterschieden zur Trennung. Eine automatisierte, sensorgestützte Sortierung dieser Baustoffe könnte diese Praxis ergänzen oder ersetzen, um die Verarbeitungsgeschwindigkeit, die Recyclingquoten, die Sortierqualität und die gesundheitlichen Bedingungen zu verbessern.
Ein gemeinsames Projekt von Partnern aus Industrie und Forschungseinrichtungen nähert sich dieser Aufgabe, indem es die Kombination von Laser-induzierter Breakdown-Spektroskopie (LIBS) und VIS/NIR-Spektroskopie untersucht und testet. Durch die gemeinsame Verarbeitung der Informationen soll die Sortierqualität verschiedener Materialien wie Beton, Hauptmauerwerksbaustoffe, organische Bestandteile usw. deutlich verbessert werden. Darüber hinaus könnten Verunreinigungen wie SO3-haltige Baustoffe (Gips, Porenbeton usw.) erkannt und getrennt werden.
Wir stellen aktuelle Fortschritte und Ergebnisse der Entwicklung eines Prüfstands vor, der LIBS mit NIR-Spektroskopie und visueller Bildgebung kombiniert. In Zukunft wird dieser Laborprototyp als vollautomatischer Messaufbau dienen, um eine Echtzeitklassifizierung von Bau- und Abbruchabfällen auf einem Förderband zu ermöglichen.