Das Suchergebnis hat sich seit Ihrer Suchanfrage verändert. Eventuell werden Dokumente in anderer Reihenfolge angezeigt.
  • Treffer 7 von 31
Zurück zur Trefferliste

Kicking the can down the Circular Economy Road – Basic needs in Standardization for Electronics- and ICT-products

  • As consequence of the European Green Deal and the European Commission's Circular Economy Action Plan, the product landscape in the EU will undergo fundamental changes. The legal requirements for products are being expanded, not least through the Proposal for an Ecodesign Regulation for Sustainable Products published by the European Commission in 2022. Following the current developments, requirements for the circularity of products will be increased next to the already existing minimum requirements for products’ energy efficiency. Following this development, the lead question has to be: Is the market, in particular small- and medium-sized enterprises, well prepared for this planned green transformation of our economy? The answer is: No, not yet. What is needed are suitable standards for the implementation of these requirements to reduce additional burdens to an appropriate level and to support fair competition between all market actors concerned. The German Institute forAs consequence of the European Green Deal and the European Commission's Circular Economy Action Plan, the product landscape in the EU will undergo fundamental changes. The legal requirements for products are being expanded, not least through the Proposal for an Ecodesign Regulation for Sustainable Products published by the European Commission in 2022. Following the current developments, requirements for the circularity of products will be increased next to the already existing minimum requirements for products’ energy efficiency. Following this development, the lead question has to be: Is the market, in particular small- and medium-sized enterprises, well prepared for this planned green transformation of our economy? The answer is: No, not yet. What is needed are suitable standards for the implementation of these requirements to reduce additional burdens to an appropriate level and to support fair competition between all market actors concerned. The German Institute for Standardization, the German Commission for Electro-technical, Electronic & Information Technologies and the Association of German Engineers have conducted a review study with the aim of identifying fundamental needs for revising existing standards and for creating new standards - both of which are intended to support and accelerate the transformation of the current economy towards a Circular Economy. More than 700.000 normative documents were analyzed, and the results were discussed and consolidated with more than 1000 experts from manufacturers (organizations), consumer- and environmental organizations as well as from the public sector. As a result, more than 200 gaps in the standardization landscape were identified. In this study, we highlight and analyze the most important needs for standardization activities in the field of electrotechnical-, electronic- and ICT-products. In the discussion with the experts for electrotechnical-, electronic- and ICT products, it has been confirmed that a timely implementation of ambitious political decisions of a circular economy requires a normative basis to ensure its consistency. Furthermore, consensus between experts was that legislation in product regulation would be key and should not be extended to the area of waste legislation. As most important standardization activities accompanying product legislation, the following were identified: (i) creation of a set of indicators enabling a holistic assessment of product circularity, (ii) quality assurance of secondary raw materials and consumers awareness of the product circularity both enabled by appropriate analytics and (iii) clear regulation concerning product liability of repaired, refurbished or remanufactured products. One issue of relevance to all experts concerns the product safety, which must not, under any circumstances, decrease when changing product design to reach a higher degree of circularity. The mentioned and further standardization activities would be essential to kick the can down the circular economy road and are analyzed and summarized in this study.zeige mehrzeige weniger

Volltext Dateien herunterladen

  • Standardization-needs-for-CE_Schlegel_et_Giegerich.pdf
    eng

Metadaten exportieren

Weitere Dienste

Teilen auf Twitter Suche bei Google Scholar Anzahl der Zugriffe auf dieses Dokument
Metadaten
Autor*innen:Moritz-Caspar Schlegel, J. Giegerich
Dokumenttyp:Beitrag zu einem Tagungsband
Veröffentlichungsform:Verlagsliteratur
Sprache:Englisch
Titel des übergeordneten Werkes (Englisch):Proceedings PLATE 2023 Conference
Jahr der Erstveröffentlichung:2023
Organisationseinheit der BAM:S Qualitätsinfrastruktur
S Qualitätsinfrastruktur / S.3 Ökodesign und Energieverbrauchskennzeichnung
Erste Seite:1
Letzte Seite:5
DDC-Klassifikation:Technik, Medizin, angewandte Wissenschaften / Ingenieurwissenschaften / Sanitär- und Kommunaltechnik; Umwelttechnik
Freie Schlagwörter:Circular Economy; Electronics; ICT; Standardization
Themenfelder/Aktivitätsfelder der BAM:Umwelt
Umwelt / Umwelt-Material-Interaktionen
Veranstaltung:PLATE Product Lifetime and the Environment Conference 2023
Veranstaltungsort:Espoo, Finland
Beginndatum der Veranstaltung:31.05.2023
Enddatum der Veranstaltung:02.06.2023
Verfügbarkeit des Dokuments:Datei im Netzwerk der BAM verfügbar ("Closed Access")
Datum der Freischaltung:07.06.2023
Referierte Publikation:Nein
Einverstanden
Diese Webseite verwendet technisch erforderliche Session-Cookies. Durch die weitere Nutzung der Webseite stimmen Sie diesem zu. Unsere Datenschutzerklärung finden Sie hier.