• Treffer 5 von 2
Zurück zur Trefferliste

Compilation and evaluation of the pressure-assisted master sintering surface for low-temperature cofired ceramics

  • Pressure-assisted sintering (PAS) is an established procedure for the production of low-temperature cofired ceramics (LTCC) without lateral shrinkage and minimal shrinkage tolerances for automotive and high-frequency applications. To develop a feasible model for the prediction of densification during that process, master sintering curves (MSCs) for the commercial LTCC DP951 were generated from thermomechanical analysis (TMA) data in the pressure regime from 2 to 500 kPa. Strain mainly related to creep deformation of the LTCC was identified by evaluation of the strain rate and was discarded for the determination of MSC parameters. It was found that no creep occurred at any pressure up to a relative density of 0.9. Different pressure levels can be modeled with the same activation energy of 400 kJ/mol. Densification curves predicted by the model were in good agreement with experimental data. Based on MSCs, the pressure-assisted master sintering surface was compiled to illustrate thePressure-assisted sintering (PAS) is an established procedure for the production of low-temperature cofired ceramics (LTCC) without lateral shrinkage and minimal shrinkage tolerances for automotive and high-frequency applications. To develop a feasible model for the prediction of densification during that process, master sintering curves (MSCs) for the commercial LTCC DP951 were generated from thermomechanical analysis (TMA) data in the pressure regime from 2 to 500 kPa. Strain mainly related to creep deformation of the LTCC was identified by evaluation of the strain rate and was discarded for the determination of MSC parameters. It was found that no creep occurred at any pressure up to a relative density of 0.9. Different pressure levels can be modeled with the same activation energy of 400 kJ/mol. Densification curves predicted by the model were in good agreement with experimental data. Based on MSCs, the pressure-assisted master sintering surface was compiled to illustrate the influence of pressure on densification. The results show that the MSC approach is a suitable method to feasibly predict the densification of LTCC during PAS.zeige mehrzeige weniger

Volltext Dateien herunterladen

  • Brandt_et_al-2015-Journal_of_the_American_Ceramic_Society.pdf
    eng

Metadaten exportieren

Weitere Dienste

Teilen auf Twitter Suche bei Google Scholar Anzahl der Zugriffe auf dieses Dokument
Metadaten
Autor*innen:Björn MiellerORCiD, Torsten Rabe
Dokumenttyp:Zeitschriftenartikel
Veröffentlichungsform:Verlagsliteratur
Sprache:Englisch
Titel des übergeordneten Werkes (Englisch):Journal of the American ceramic society
Jahr der Erstveröffentlichung:2015
Herausgeber (Institution):American Ceramic Society
Verlag:Blackwell Publishing
Verlagsort:Malden
Jahrgang/Band:98
Ausgabe/Heft:11
Erste Seite:3503
Letzte Seite:3508
Freie Schlagwörter:Activation energy; DP951; LTCC; Low temperature co-fired ceramics; Master sintering curve
DOI:10.1111/jace.13732
ISSN:0002-7820
ISSN:1551-2916
Bemerkung:
Geburtsname von Mieller, Björn: Brandt, B. -  Birth name of Mieller, Björn: Brandt, B.
Verfügbarkeit des Dokuments:Datei im Netzwerk der BAM verfügbar ("Closed Access")
Datum der Freischaltung:20.02.2016
Referierte Publikation:Ja
Datum der Eintragung als referierte Publikation:12.11.2015
Einverstanden
Diese Webseite verwendet technisch erforderliche Session-Cookies. Durch die weitere Nutzung der Webseite stimmen Sie diesem zu. Unsere Datenschutzerklärung finden Sie hier.