Das Suchergebnis hat sich seit Ihrer Suchanfrage verändert. Eventuell werden Dokumente in anderer Reihenfolge angezeigt.
  • Treffer 20 von 386
Zurück zur Trefferliste

Surface characteristics of LTCC substrates fabricated by pressure-assisted sintering

  • Plane LTCC substrates can be produced in zeroshrinkage technology by pressure-assisted sintering. The application of axial pressure during sintering supports densification, enhances cofiring of different materials, and restrains deformation. However, the sintered surfaces are affected by the release tapes and by the setters used in the pressure-assisted sintering process. In this study, the effect of release tape particle size on the surface properties of sintered substrates was investigated. Moreover, the substitution of release tape by the use of a vitreous carbon setter was tested. Surface roughness and sheet resistances of metallic thin films on the respective samples were determined. It was found that the roughness of the substrates is not directly correlated with the adequacy of the surface for thin-film deposition. Compared with a freely sintered sample with an average roughness (Ra) of 0.31 μm, pressure-assisted sintering created smoother surfaces using finegrained releasePlane LTCC substrates can be produced in zeroshrinkage technology by pressure-assisted sintering. The application of axial pressure during sintering supports densification, enhances cofiring of different materials, and restrains deformation. However, the sintered surfaces are affected by the release tapes and by the setters used in the pressure-assisted sintering process. In this study, the effect of release tape particle size on the surface properties of sintered substrates was investigated. Moreover, the substitution of release tape by the use of a vitreous carbon setter was tested. Surface roughness and sheet resistances of metallic thin films on the respective samples were determined. It was found that the roughness of the substrates is not directly correlated with the adequacy of the surface for thin-film deposition. Compared with a freely sintered sample with an average roughness (Ra) of 0.31 μm, pressure-assisted sintering created smoother surfaces using finegrained release tapes (Ra = 0.18 μm) and rougher surfaces using coarse release tapes (Ra = 0.46 μm). Still, sheet resistances were higher on all sinter-pressed samples. The vitreous carbon setter created unusual trenched surface structures, characterized by varying roughness values and intermediate sheet resistances on the LTCCs tested.zeige mehrzeige weniger

Metadaten exportieren

Weitere Dienste

Teilen auf Twitter Suche bei Google Scholar Anzahl der Zugriffe auf dieses Dokument
Metadaten
Autor*innen:Björn MiellerORCiD, Torsten Rabe
Dokumenttyp:Zeitschriftenartikel
Veröffentlichungsform:Verlagsliteratur
Sprache:Englisch
Titel des übergeordneten Werkes (Englisch):Journal of microelectronics and electronic packaging
Jahr der Erstveröffentlichung:2013
Herausgeber (Institution):International Microelectronics and Packaging Society (IMAPS)
Verlagsort:Washington, DC
Jahrgang/Band:10
Ausgabe/Heft:4
Erste Seite:144
Letzte Seite:149
DOI:10.4071/imaps.385
ISSN:1551-4897
Bemerkung:
Geburtsname von Mieller, Björn: Brandt, B. -  Birth name of Mieller, Björn: Brandt, B.
Verfügbarkeit des Dokuments:Physisches Exemplar in der Bibliothek der BAM vorhanden ("Hardcopy Access")
Bibliotheksstandort:Sonderstandort: Publica-Schrank
Datum der Freischaltung:20.02.2016
Referierte Publikation:Nein
Einverstanden
Diese Webseite verwendet technisch erforderliche Session-Cookies. Durch die weitere Nutzung der Webseite stimmen Sie diesem zu. Unsere Datenschutzerklärung finden Sie hier.