• Treffer 1 von 0
Zurück zur Trefferliste

Pressure-assisted sintering of buried thick film resistors in LTCC

  • In this work, the effect of the pressure-assisted sintering process on buried thick film resistors integrated in LTCC multilayer has been studied. Four commercial resistor pastes with sheet resistivities between 10 kΩ and 10 MΩ/cm were analyzed. First they were characterized by SEM/EDX, XRD and Laser diffraction to determine composition and particle distribution. The pastes consist of isolating particles and of Ruthenium based particles that are supposed to build the conductive phase. The pastes were screen printed on LTCC green tape (DP 951) and buried in four layer laminates. Sintering was done in two ways, pressureless (PLS) and also pressure-assisted (PAS). The pressureless sintered resistors showed electrical resistance values roughly in the range of the nominal sheet resistivity and only relatively small fluctuation within one sample. The PAS samples on the other hand showed significantly higher resistances and larger deviations. The microstructure of the sintered resistors wasIn this work, the effect of the pressure-assisted sintering process on buried thick film resistors integrated in LTCC multilayer has been studied. Four commercial resistor pastes with sheet resistivities between 10 kΩ and 10 MΩ/cm were analyzed. First they were characterized by SEM/EDX, XRD and Laser diffraction to determine composition and particle distribution. The pastes consist of isolating particles and of Ruthenium based particles that are supposed to build the conductive phase. The pastes were screen printed on LTCC green tape (DP 951) and buried in four layer laminates. Sintering was done in two ways, pressureless (PLS) and also pressure-assisted (PAS). The pressureless sintered resistors showed electrical resistance values roughly in the range of the nominal sheet resistivity and only relatively small fluctuation within one sample. The PAS samples on the other hand showed significantly higher resistances and larger deviations. The microstructure of the sintered resistors was again investigated by SEM and XRD. It seems that the resistivity is determined by the ratio of the two Ruthenium phases RuO2 and Pb2Ru2O6.5, where RuO2 has the higher conductivity. Buried resistors cannot be trimmed by a laser to adjust the resistance. But we discovered that a refiring step will reduce and normalize the resistivity of the PAS resistors significantly.zeige mehrzeige weniger

Volltext Dateien herunterladen

  • Pressure-Assisted Sintering of Buried Thick Film Resistors in LTCC.pdf
    eng

Metadaten exportieren

Weitere Dienste

Teilen auf Twitter Suche bei Google Scholar Anzahl der Zugriffe auf dieses Dokument
Metadaten
Autor*innen:Andreas Heunisch, Victor de Seauve, Torsten Rabe
Dokumenttyp:Beitrag zu einem Tagungsband
Veröffentlichungsform:Verlagsliteratur
Sprache:Englisch
Titel des übergeordneten Werkes (Englisch):IMAPS/ACerS 11th International CICMT conference and exhibition (Proceedings)
Jahr der Erstveröffentlichung:2015
Erste Seite:239
Letzte Seite:244
Freie Schlagwörter:Buried thick film resistors; LTCC Multilayer; Pressure-assisted sintering
Veranstaltung:IMAPS/ACerS 11th International CICMT conference and exhibition
Veranstaltungsort:Dresden, Germany
Beginndatum der Veranstaltung:20.04.2015
Enddatum der Veranstaltung:23.04.2015
DOI:10.4071/CICMT-WP21
ISBN:978-1510804562
Verfügbarkeit des Dokuments:Datei im Netzwerk der BAM verfügbar ("Closed Access")
Datum der Freischaltung:20.02.2016
Referierte Publikation:Nein
Einverstanden
Diese Webseite verwendet technisch erforderliche Session-Cookies. Durch die weitere Nutzung der Webseite stimmen Sie diesem zu. Unsere Datenschutzerklärung finden Sie hier.