Das Suchergebnis hat sich seit Ihrer Suchanfrage verändert. Eventuell werden Dokumente in anderer Reihenfolge angezeigt.
  • Treffer 20 von 25
Zurück zur Trefferliste

Guidlines for flexible joint transition systems RTD 1007-4:2020

  • Flexible joint transition systems in the form of bituminous joint transitions, type 4.1a according to RTD1007-1, have been used in the Netherlands with varying success. The lifespan in practice was found to vary greatly: between 1 and 5 years. This is too short a lifespan in relation to the lifespan of the layers of asphalt pavement. Ideally, the replacement of these bituminous joint transitions should take place simultaneously as the maintenance of the asphalt layers. In the meantime, research has been carried out nationally and internationally into improving the life span of bituminous joint transitions. In Germany and Switzerland, the regulations have been shown to lead to a life span of more than 10 years. On this basis, ETAG032-3 was established in the context of EOTA in 2013. In a competition "Silent sustainable joint transitions" held by the Dutch Directorate-General for Public Works and Water Management in the period 2007-2012, three flexible bituminous joint transitions haveFlexible joint transition systems in the form of bituminous joint transitions, type 4.1a according to RTD1007-1, have been used in the Netherlands with varying success. The lifespan in practice was found to vary greatly: between 1 and 5 years. This is too short a lifespan in relation to the lifespan of the layers of asphalt pavement. Ideally, the replacement of these bituminous joint transitions should take place simultaneously as the maintenance of the asphalt layers. In the meantime, research has been carried out nationally and internationally into improving the life span of bituminous joint transitions. In Germany and Switzerland, the regulations have been shown to lead to a life span of more than 10 years. On this basis, ETAG032-3 was established in the context of EOTA in 2013. In a competition "Silent sustainable joint transitions" held by the Dutch Directorate-General for Public Works and Water Management in the period 2007-2012, three flexible bituminous joint transitions have already been tested, two of which were ultimately found to be suitable. These have been included in the multi-choice matrix (RTD 1007-1) as concept 4.1b (anchored bituminous joint transition) and 4.1c (unanchored bituminous joint transition with stretch-spreading inlay and poured asphalt edge beams). Monitoring these joint transitions in practice over the past 8 years has shown that the desired life span is achievable with these improved joint transitions. It is expected that the improvement in life span achieved abroad can also be realised in the Netherlands if several aspects specific to the Netherlands are taken into account:  For large parts of the Dutch main road network, the traffic intensity of 500,000 heavy vehicles per year assumed in the ETAG032-3 is insufficient. This is a factor 4 to 5 higher on the busiest main roads in the Netherlands.  On 90% of the Dutch main road network, in contrast to countries such as Germany and Switzerland, an open layer (ZOAB (zeer open asfaltbeton [very open asphalt concrete])) is used.  In the Netherlands, in contrast to countries such as Germany and Switzerland, bridges and viaducts are made on a large scale of prefabricated beams and 'floating' support systems that consist entirely of rubber supports that can be deformed all-round. Such constructions have a less favourable, high-frequency deformation behaviour under traffic load.  In Germany and Switzerland, a minimum joint mass temperature of -20 °C is assumed to test bituminous joint transitions. For the Netherlands, -15 °C is assumed, which has a favourable effect. The present second version of RTD 1007-4 is a guideline for the development and realisation of a new generation of more durable flexible joint transitions with a minimum design life of 10-15 years and is a guideline for contractors to demonstrate that a flexible joint transition system meets the requirements as set out in the Directorate-General for Public Works and Water Management guideline RTD 1007-2.zeige mehrzeige weniger

Volltext Dateien herunterladen

  • Recknagel_RTD1007-4-2.0-2020-English Version.pdf
    eng

Metadaten exportieren

Weitere Dienste

Teilen auf Twitter Suche bei Google Scholar Anzahl der Zugriffe auf dieses Dokument
Metadaten
Autor*innen:F. van Beek, P. Kuijper, J. Voskuilen, S. Hean, Christoph Recknagel, S. D. Mookhoek, D. van Vliet
Dokumenttyp:Handbuch
Veröffentlichungsform:Graue Literatur
Sprache:Englisch
Jahr der Erstveröffentlichung:2020
Organisationseinheit der BAM:7 Bauwerkssicherheit
7 Bauwerkssicherheit / 7.1 Baustoffe
Herausgeber (Institution):Directorate-General for Public Works and Water Management, Ministry of Infrastructure and Water Management
Verlagsort:Rijkswaterstaat
Jahrgang/Band:Version 2.0
Erste Seite:1
Letzte Seite:77
DDC-Klassifikation:Technik, Medizin, angewandte Wissenschaften / Ingenieurwissenschaften / Ingenieurbau
Freie Schlagwörter:Approval requirements; Extension joints; Highway pavements; Technical rule
Themenfelder/Aktivitätsfelder der BAM:Infrastruktur
Verfügbarkeit des Dokuments:Datei im Netzwerk der BAM verfügbar ("Closed Access")
Datum der Freischaltung:06.04.2022
Referierte Publikation:Nein
Einverstanden
Diese Webseite verwendet technisch erforderliche Session-Cookies. Durch die weitere Nutzung der Webseite stimmen Sie diesem zu. Unsere Datenschutzerklärung finden Sie hier.