TY - JOUR A1 - Pimienta, Pierre A1 - McNamee, Robert A1 - Robert, Fabienne A1 - Boström, Lars A1 - Huang, Shan-Shan A1 - Mróz, Katarzyna A1 - Davie, Colin A1 - Mohaine, Siyimane A1 - Alonso, Maria Cruz A1 - Bodnarova, Lenka A1 - Bosnjak, Josipa A1 - Dal Pont, Stefano A1 - Dao, Vinh A1 - Dauti, Dorjan A1 - Dehn, Frank A1 - Felicetti, Roberto A1 - Hager, Izabela A1 - Hela, Rudolf A1 - Hozjan, Tomaz A1 - Juknat, Michael A1 - Jumppanen, Ulla-Maija A1 - Kirnbauer, Johannes A1 - Kolsek, Jerneja A1 - Korzen, Manfred A1 - Lakhani, Hitesh A1 - Lion, Maxime A1 - Lo Monte, Francesco A1 - Maluk, Cristian A1 - Meftah, Fekri A1 - Miah, Md Jihad A1 - Millard, Alain A1 - Mindeguia, Jean-Christophe A1 - Moreau, Bérénice A1 - Msaad, Yahia A1 - Ozawa, Mitsuo A1 - Pesavento, Francesco A1 - Pham, Duc Toan A1 - Pistol, Klaus A1 - Rickard, Ieuan A1 - Rodrigues, Joao Paulo Correia A1 - Roosefid, Mohsen A1 - Schneider, Martin A1 - Sharma, Umesh Kumar A1 - Sideris, Kosmas A1 - Stelzner, Ludwig A1 - Weber, Benedikt A1 - Weise, Frank T1 - Recommendation of RILEM TC 256-SPF on fire spalling assessment during standardised fire resistance tests: complementary guidance and requirements N2 - The recommendation is based on the co-authors’ work organized by the RILEM TC 256-SPF “Spalling of concrete due to fire: testing and modelling”. It aims to provide useful information, guidance and best practices in fire spalling assessment to laboratories that perform large-scale tests based on fire resistance test standards. It provides guidance on the spalling observation techniques during testing, as well as post-test spalling quantification/assessment methods. This document is intended to be used in conjunction with the fire resistance test standards, e.g. EN 1363-1 and ISO 834-1. KW - Concrete KW - Fire spalling KW - Large scale tests KW - Standardised fire resistance tests PY - 2024 DO - https://doi.org/10.1617/s11527-023-02248-z SN - 1871-6873 VL - 57 IS - 1 SP - 1 EP - 12 PB - Springer CY - Dordrecht AN - OPUS4-59288 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Frei, Vivian A1 - Pirskawetz, Stephan A1 - Thiele, Marc A1 - Rogge, Andreas T1 - Ermüdungsverhalten von Beton für unterschiedliche Probekörpergeometrien N2 - Die zunehmende Anwendung hochfesten Betons in ermüdungsbelasteten Bauwerken, herausfordernde Belastungsszenarien im Bereich von On- und Offshore Windenergieanlagen bezüglich sehr hoher Lastwechselzahlen sowie das gleichzeitige Streben nach energie- und ressourcenschonendem Bauen stellen die Bemessung von Beton gegen Ermüdung vor neue Aufgaben. Eine Vielzahl von Studien beschreibt bereits die Auswirkung von Einflussfaktoren wie Mischungszusammensetzung, Feuchte, Probekörpergröße oder Belastungsart auf die Ermüdungsfestigkeit und den Ermüdungsprozess. Aufgrund der unterschiedlichen Geometrien und Mischungen der in den verschiedenen Studien verwendeten Proben sind die Auswirkungen der Einflussfaktoren jedoch kaum miteinander vergleichbar. In dem vom Bundesministerium für Wirtschaft und Klimaschutz (BMWK) geförderten Verbundprojekt WinConFat wurden deshalb verschiedene Einflussfaktoren gezielt an Proben mit einheitlichen Mischungen untersucht. Das durch die Bundesanstalt für Materialforschung und -prüfung (BAM) bearbeitete Teilprojekt fokussierte sich auf den „Einfluss der Probengeometrie und -größe auf die Ermüdung von Beton“. Neben der Erhebung von Daten zur Ermüdungsfestigkeit wurde der Ermüdungsprozess mit zerstörungsfreien Prüf- und Messmethoden untersucht. Diese Prüfmethoden wurden auch hinsichtlich ihrer Anwendbarkeit zur Erfassung der ermüdungsbedingten Schädigungsentwicklung an Betonbauwerken im Rahmen von Monitoringkonzepten bewertet. Untersucht wurden die Ermüdungsfestigkeiten und der Ermüdungsprozess an Zylindern mit drei unterschiedlichen Betonmischungen sowie unterschiedlicher Größe und Schlankheit. Die Ergebnisse dieser Untersuchungen werden im Folgenden vorgestellt und diskutiert. KW - Ermüdung KW - Hochfester Beton KW - Probengröße KW - Probengeometrie PY - 2024 VL - 644 SP - 1 EP - 135 PB - Beuth CY - Berlin AN - OPUS4-59647 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn T1 - Funktionalisierung durch laser-induzierte periodische Oberflächenstrukturen N2 - Der Vortrag gibt einen Überblick über die vielfältigen Möglichkeiten der Oberflächenfunktionalisierung mittels Mikro- und Nanostrukturierung durch Ultrakurzpuls-Lasermaterialbeabeitung. Dies schließt eine Diskussion des Phänomens der Laser-induzierten periodischen Oberflächenstrukturen (LIPSS, engl.: Laser-induced Periodic Surface Structures, Ripples), sowie deren Klassifikation und Bildungsmechanismen mit ein. Ein Schwerpunkt der Präsentation liegt auf der Diskussion verschiedener Anwendungsmöglichkeiten der LIPSS in Bereichen der Optik, Fluidik, Tribologie und Medizin, sowie auf einem Ausblick auf die industrielle Skalierbarkeit der LIPSS-Technologie. T2 - 1. Netzwerktreffen 2024 des UKPL-Innovationsnetzwerks CY - Rostock, Germany DA - 11.03.2024 KW - Laser-induced Periodic Surface Structures (LIPSS) KW - Oberflächenfunktionalisierung KW - Mikrostrukturen KW - Nanostrukturen KW - Ultrakurzpuls-Laserbearbeitung PY - 2024 AN - OPUS4-59657 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hodoroaba, Vasile-Dan T1 - Delivering Impact - A new ISO standard on the identification of nanoparticles N2 - Nanoparticles (NPs) are tiny – around 1 to 100 billionths of a meter – and can have different chemistries and behaviours than the same material of larger size. This property has led to advances in a wide range of industries, but it can also confer toxicity. Size measurements are the main way NPs are identified but a lack of standardised methods for identifying ones with complex shapes has hindered evaluation of their potential harm. KW - Nanoparticles KW - Standardisation KW - Particle size distribution KW - nPSize KW - ISO 21363 PY - 2024 UR - https://www.euramet.org/casestudies/casestudiesdetails/news/default-c3b26209e8 SP - 1 EP - 2 PB - EURAMET CY - Braunschweig AN - OPUS4-59626 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander A1 - Königsbauer, Korbinian A1 - Nöther, N. A1 - Färber, J. A1 - Schaller, M.-B. A1 - Krebber, K. T1 - Verteilte POF-basierte faseroptische Sensoren zur Infrastrukturüberwachung in der Geotechnik N2 - Wir präsentieren unsere Forschungsergebnisse zur Entwicklung eines faseroptischen Sensorsystems mit polymeroptischen Fasern integriert in Geokunststoffe für die Überwachung von geotechnischen Anlagen. Das Sensorsystem dient der räumlichen Auflösung lokaler Dehnungsereignisse im für Anwender signifikanten Größenordnungsbereich von 3 % bis 10 %. Das gesamte Sensorkonzept besteht aus einem praxistauglichen Messsystem basierend auf der digitalen inkohärenten optischen Frequenzbereichsreflektometrie (I-OFDR) und einer Sensormatte in Form eines Geotextils mit integrierten faseroptischen perfluorierten polymeroptischen Fasern (PF-POFs). T2 - DGZfP Fachtagung Bauwerksdiagnose 2024 CY - Berlin, Germany DA - 29.02.2024 KW - Ortsverteilte faseroptische Sensorik KW - Optische Frequenzbereichsreflektometrie KW - Bauwerksüberwachung KW - Sensorbasierte Geokunststoffe PY - 2024 AN - OPUS4-59633 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Artinov, Antoni A1 - Karkhin, Victor A1 - Bachmann, Marcel A1 - Rethmeier, Michael T1 - Simulation of solidification during keyhole laser welding of thick plates T1 - Моделирование процесса кристаллизациипри лазерной сварке со сквозным проплавлением пластин большой толщины N2 - A method of solving the thermo-fluid dynamics problem is presented, enabling the prediction of the shape and dimensions of the weld pool during keyhole laser welding of thick plates. It is shown that the rear weld pool boundary can be satisfactorily approximated by a set of superellipses (Lamé curves). The presence of a convex rear weld pool boundary in the mid-plane has been observed experimentally and reproduced numerically. It was shown that in this zone the concentration of liquating impurities increases and the local solidification temperature decreases, contributing to the susceptibility to hot cracking. KW - Laser beam welding KW - Three-dimensional crystallization KW - Mathematical modeling KW - Superellipse KW - Thick steel plates PY - 2024 DO - https://doi.org/10.34641/SP.2023.1062.5.041 VL - 5 SP - 31 EP - 36 AN - OPUS4-59639 LA - rus AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Klewe, Tim A1 - Strangfeld, Christoph A1 - Ritzer, Tobias A1 - Kruschwitz, Sabine T1 - GPR Dataset of Moisture Measurements on Building Floors in Laboratory and On-Site N2 - Related work Laboratory Study: Combining Signal Features of Ground-Penetrating Radar to Classify Moisture Damage in Layered Building Floors https://doi.org/10.3390/app11198820 On-Site Study: TBA Doctoral Thesis: Non-destructive classification of moisture deterioration in layered building floors using ground penetrating radar https://doi.org/10.14279/depositonce-19306 Measurement Parameters The GPR measurements were carried out with the SIR 20 from GSSI and a 2 GHz antenna pair (bandwidth 1 GHz to 3 GHz) in common-offset configuration. Each B-Scan consists of N A-Scans, each including 512 samples of a 11 ns time window. Survey lines were recorded with 250 A-Scans/ meter, which equals a 4 mm spacing between each A-Scan No Gains were applied. Folder Description: Lab_dry, Lab_insulDamage, Lab_screedDamage - each contain 168 Measurements (B-Scans) in .csv on 84 dry floors, floors with insulation damage and screed damage. - each floor setup was measured twice on two orthogonal survey lines, indicated by _Line1_ and _Line2_ in the file name. - the file names encode the building floor setup e.g. CT50XP100 describes a 50 mm cement screed with 100 mm extruded polystyrene below - the material codes are CT: cement screed, CA: anhydrite screed, EP: expanded polystyrene, XP: extruded polystyrene, GW: glass wool, PS: perlites further information can be found in the publication https://doi.org/10.3390/app11198820 OnSite_ - 5 folders containing B-Scans on 5 different practical moisture damages - the building floor setup is encoded according to the lab with an additional measurement point numbering at the start and a damage case annotation at the end of the file name with _dry, _insulationDamage and_screedDamage File Description: B-Scans, Measurement files - no header - dimension: 512 x N data point with N beeing the number of A-Scans including 512 samples of a 11 ns time window. - survey lines were recorded with 250 A-Scans/ meter, which equals a 4 mm spacing between each A-Scan Moisture References - Moist_Reference of On-Site Locations include the columns MeasPoint: Measurement point, wt%Screed: moisture content of screed layer in mass percent; wt%Insul: moisture content of insulation layer in mass percent. References were obtained by drilling cores with 68 mm diameter in the center of each survey line. - Moist_Reference_Screed of Lab data include the columns Screed: Screed material and thickness in mm, wt%Screed moisture content of screed layer in mass percent - Moist Reference_Insul of Lab data include the columns Insulation: Insulation material and thickness in mm, water addition in l: water added to the insulation layer in liters, V%Insulation: water added to the insulation layer in volume percent, RH%: resulting relative humidy in the insulation layer during measurement. These References are only avaible for Lab measurements on insulation damages. KW - GPR KW - Material Moisture KW - Building Floors KW - Laboratory KW - On-Site PY - 2024 DO - https://doi.org/10.5281/zenodo.10776684 PB - Zenodo CY - Geneva AN - OPUS4-59609 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lu, Xin A1 - Hicke, Konstantin A1 - Krebber, Katerina T1 - Distributed acoustic sensing to monitor ground motion/movement at multi-frequency bands N2 - A novel distributed acoustic sensing technique is proposed that exploits both phase and amplitude of the Rayleigh backscattered light to quantify the environmental variation. The system employs a wavelength-scanning laser and an imbalanced Mach-Zehnder interferometer to acquire the reflection spectra and the phase of the detected light, respectively. Fading-free and low-frequency measurements are realized via the crosscorrelation of the reflection spectra. The discrete crosscorrelation is used to circumvent the nonlinear frequency sweeping of the laser. Based on the phase of the backscattered light, it is possible to quantify fast environmental variations. The whole system requires no hardware modification of the existing system and its functionality is experimentally validated. The proposed system has the potential to monitor ground motion/movement at very low frequency band like subsidence around mining areas and at high frequency band like earthquakes and vibrations induced by avalanches. KW - Distributed acoustic sensing KW - DAS KW - Distributed fiber optic sensing KW - Ground motion detection KW - Subsidence monitoring PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-596129 DO - https://doi.org/10.1109/JLT.2024.3358495 SP - 1 EP - 8 PB - Optical Society und IEEE Photonics Society AN - OPUS4-59612 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hicke, Konstantin T1 - Faseroptisches Monitoring von Brückenbauwerken N2 - Die Möglichkeiten von verteilter faseroptischer Sensorik (DFOS) im Allgemeinen und für das Monitoring von Bauwerken im Besonderen werden dargestellt und beispielhafte Anwendungen von DFOS im Kontext Brückenmonitoring illustriert. T2 - DGZfP Fachtagung Bauwerksdiagnose 2024 CY - Berlin, Germany DA - 29.02.2024 KW - Bauwerksüberwachung KW - Brückenmonitoring KW - Verteilte faseroptische Sensorik KW - Dynamische Strukturantwort KW - Spanndrahtbruchdetektion PY - 2024 AN - OPUS4-59613 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Trogadas, P. A1 - Cho, J. I. S. A1 - Rasha, L. A1 - Lu, X. A1 - Kardjilov, N. A1 - Markötter, Henning A1 - Manke, I. A1 - Shearing, P. R. A1 - Brett, D. J. L. A1 - Coppens, M. O. T1 - A nature-inspired solution for water management in flow fields for electrochemical devices N2 - A systematic, nature-inspired chemical engineering approach is employed to solve the issue of flooding in electrochemical devices. The mechanism of passive water transport utilized by lizards living in arid environments is leveraged to design flow-fields with a microchannel structure on their surface, through which capillary pressure rapidly removes the water generated in the electrochemical device. This water management strategy is implemented in proton exchange membrane fuel cells (PEMFCs) with a lunginspired flow-field, which ensures uniform distribution of reactants across the catalyst layer. Jointly, this nature-inspired approach results in flood-free, stable operation at 100% RH and a B60% increase in current (B1.9 A cm-2) and peak power density (B650 mW cm−2) compared to current PEMFCs with a flood-prone, serpentine flow-field (B0.8 A cm-2 and 280 mW cm-2, respectively). This significant advance allows for PEMFC operation at fully humidified conditions. KW - Neutron imaging KW - X-ray tomography KW - Fuel cell PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-596662 DO - https://doi.org/10.1039/d3ee03666a VL - 17 SP - 2007 EP - 2017 PB - Royal Society of Chemistry (RSC) AN - OPUS4-59666 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -