TY - VIDEO T1 - Bio-based concrete - Materials innovation for sustainable future construction N2 - Concrete is typically perceived as a grey material that is relatively cheap and easy to use for mass application. The global relevance of concrete is often ignored despite its tremendous environmental, economic, and social impact. Construction materials are a major impact on the climate change, but building is inevitable for social and economic development. Therefore, it is important to develop more sustainable materials to build habitat and infrastructures. A reasonable approach to build more sustainably with concrete is to use agricultural by-products as chemical or fibrous performance enhancers and/or as replacement of cement in the binder. KW - Bio-based Concrete PY - 2019 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-49716 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - VIDEO T1 - Biobeton - Werkstoffinnovation für nachhaltiges zukünftiges Bauen N2 - Beton wird typischerweise als graues Material wahrgenommen, das relativ preiswert ist und einfach in der Massenanwendung eingesetzt werden kann. Die globale Relevanz von Beton wird trotz seiner enormen ökologischen, wirtschaftlichen und sozialen Bedeutung oft ignoriert. Baustoffe sind ein großer Einflussfaktor für den Klimawandel, aber Bauen ist für die soziale und wirtschaftliche Entwicklung unvermeidlich. Daher ist es wichtig, nachhaltigere Materialien zu entwickeln, um Lebensräume und Infrastrukturen zu schaffen. Ein sinnvoller Ansatz, um mit Beton nachhaltiger zu bauen, ist die Verwendung landwirtschaftlicher Nebenprodukte als chemische oder faserförmige Leistungsförderer und/oder als Ersatz von Zement im Bindemittel. KW - Biobeton PY - 2019 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-48695 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN T1 - Forschungsprogramm 2019 - 2021 N2 - Die voranschreitende Digitalisierung, die Globalisierung sowie die daraus resultierende beschleunigte technologische Entwicklung bringen heute für die Industrieländer Herausforderungen im Hinblick auf Wachstum, Beschäftigung und Strukturwandel mit sich, denen nur mit einer entsprechenden Innovationsdynamik und -dichte begegnet werden kann. Grundvoraussetzung hierfür ist eine leistungsfähige Forschung und Entwicklung ebenso wie Wissens- und Technologietransfer zur Umsetzung von Forschungsergebnissen in marktfähige Produkte und Dienstleistungen. Europa hat sich im Rahmen des Lissabon-Prozesses zum Ziel gesetzt, den Anteil der Forschungsausgaben am Bruttoinlandsprodukt auf 3 % zu steigern. Um die Forschungsinfrastruktur in der Bundesrepublik zu stärken und global wettbewerbsfähig zu bleiben, hat die Bundesregierung mit der Hightech-Strategie 2025 einen weiteren wichtigen Schritt zur Förderung des wissenschaftlich-technischen Fortschritts in Deutschland getan. Forschungsprogramme sind sowohl für Forschungseinrichtungen als auch für Mittelgeber ein wichtiges Instrument für die Darstellung und Steuerung ihrer Aktivitäten. Dies gilt auch für die Bundeseinrichtungen mit Forschungs- und Entwicklungsaufgaben, zu denen die Bundesanstalt für Materialforschung und -prüfung (BAM) zählt. Die BAM verfügt über einen klaren gesetzlichen Auftrag für die Sicherheit in Technik und Chemie. Ihre Forschung ist mit der Wahrnehmung öffentlicher Aufgaben verbunden. Das Forschungsprogramm zeigt Perspektiven im Bereich ihres Aufgabenfeldes sowie ihrer damit verbundenen Forschungsaktivitäten transparent und politisch nutzbar auf und dient darüber hinaus der Koordinierung der Ressortforschung. Das Forschungsprogramm der BAM wird alle zwei Jahre aktualisiert. Es gibt einen Überblick über die aktuellen und zukünftigen Forschungsthemen und die hierfür erforderlichen Rahmenbedingungen. PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-577499 SP - 1 EP - 44 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-57749 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN ED - Panne, Ulrich T1 - BAM Report 2017/2018 N2 - Wir arbeiten für eine ausgeprägte Sicherheitskultur in Deutschland und Sicherheitsstandards, die auch in Zukunft höchsten Anforderungen genügen. Sicherheit macht Märkte. In den Spitzen- und Schlüsseltechnologien Materialwissenschaft, Werkstofftechnik und Chemie leistet die BAM einen entscheidenden Beitrag zur technischen Sicherheit von Produkten, Prozessen und der Lebens- und Arbeitswelt der Menschen. Als Bundesoberbehörde sind wir wirtschaftlich unabhängig und fungieren als neutraler Moderator externer Entscheidungsprozesse. Darüber hinaus ermöglichen wir den Transfer wissenschaftlicher Erkenntnisse in die Politik und für die Erfüllung öffentlicher Aufgaben. In unseren nationalen und internationalen Netzwerken betreiben wir Technologietransfer und wir nutzen ihre Kompetenzen und wertvollen Impulse für unsere aktuelle Arbeit und die zukünftige Ausrichtung der BAM. Im Rahmen unserer gesetzlichen und gesellschaftspolitischen Aufgaben identifizieren, kommunizieren und implementieren wir Anforderungen an die Sicherheit in Technik und Chemie für die Gesellschaft von morgen. Mit unseren Innovationen in Forschung und Entwicklung und der Weitergabe unseres Wissens fördern wir die deutsche Wirtschaft. N2 - We make every effort to produce a strong safety culture in Germany and safety standards that will meet the highest requirements in the future. Safety creates markets. At the cutting edge of key technologies of materials science, materials engineering and chemistry, BAM makes a crucial contribution to the technical safety of products, processes and to people’s life and work environment. As a senior federal institute, we are financially independent and act as a neutral moderator in external decision-making processes. In addition, we ensure the transfer of scientific knowledge by providing advice to politicians and performing public duties. We perform technology transfer in our national and international networks and use their competences and valued ideas for both our current work and in setting BAM’s future direction. As part of our legal and political tasks we identify, communicate and implement requirements in "Safety in technology and chemistry" for tomorrow’s society. Innovations in research and development and the dissemination of our knowledge help promote the German industry. T3 - BAM Reports/Jahresberichte - 2017/2018 PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-480400 SN - 0934-9456 SN - 2627-0153 SN - 2940-7532 N1 - Volltext (PDF) in deutsch und englisch - Full text (PDF) in German and English. VL - 2017/2018 SP - 1 EP - 155 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-48040 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Erdmann, Maren A1 - Böhning, Martin A1 - Niebergall, Ute T1 - Physical and chemical effects of biodiesel storage on high-density polyethylene: Evidence of co-oxidation N2 - The physical and chemical effects of diesel and biodiesel fuels on two high-density polyethylene (PE-HD) types were investigated. Both semi-crystalline PE-HD are common thermoplastic materials for container and storage tank applications. Biodiesel, a composition of unsaturated fatty acid esters from renewable resources, was chosen as it is regarded a possible green alternative to fossil fuels. The study aims at identifying significant differences between biodiesel and conventional diesel fuels based on the differences in the chemical nature of the two. The physical effects of the fuels on the polymer at first comprises the sorption behavior, i.e. kinetics and final equilibrium concentration. Not only are both fuels absorbed by the amorphous phase of the semi-crystalline PE-HD, they also induce a plasticization effect that modifies the molecular mobility and therefore also the characteristic yielding properties, manifest in the obtained stress-strain curves. The chemical effects related to degradation phenomena is investigated by a long-term storage scenario using partially immersed tensile test specimens in diesel and biodiesel. We were able to confirm the proposed co-oxidation mechanism by Richaud et al. for polyethylene-unsaturated penetrant systems on a larger scale based on practical tensile tests. One of the investigated polyethylene grades subjected to tensile drawing showed a significant loss of plastic deformation and the onset of premature failure after 150 days of storage in biodiesel. Further biodiesel storage showed a systematically reduced elongation at break before necking. None of these effects were observed in diesel. Oxidation of fuels and polymer after progressing storage times were analyzed by the evolution of carbonyl species in FT-IR/ATR spectroscopy. KW - Biodiesel KW - Degradation KW - Long-term storage KW - Sorption KW - Diesel PY - 2019 DO - https://doi.org/10.1016/j.polymdegradstab.2019.01.018 SN - 0141-3910 VL - 161 IS - 1 SP - 139 EP - 149 PB - Elsevier CY - Amsterdam AN - OPUS4-47268 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Waske, Anja A1 - Dzekan, D. A1 - Sellschopp, K. A1 - Berger, D., A1 - Stork, A. A1 - Nielsch, K. A1 - Fähler, S. T1 - Energy harvesting near room temperature using a thermomagnetic generator with a pretzel-like magnetic flux topology N2 - To date, there are very few technologies available for the conversion of low-temperature waste heat into electricity. Thermomagnetic generators are one approach proposed more than a century ago. Such devices are based on a cyclic change of magnetization with temperature. This switches a magnetic flux and, according to Faraday’s law, induces a voltage. Here we demonstrate that guiding the magnetic flux with an appropriate topology of the magnetic circuit improves the performance of thermomagnetic generators by orders of magnitude. Through a combination of experiments and simulations, we show that a pretzel-like topology results in a sign reversal of the magnetic flux. This avoids the drawbacks of previous designs, namely, magnetic stray fields, hysteresis and complex geometries of the thermomagnetic material. Our demonstrator, which is based on magnetocaloric plates, illustrates that this solid-state energy conversion technology presents a key step towards becoming competitive with thermoelectrics for energy harvesting near room temperature. KW - Energy harvesting KW - Thermomagnetic generator PY - 2019 DO - https://doi.org/10.1038/s41560-018-0306-x SN - 2058-7546 VL - 4 SP - 68 EP - 74 PB - Nature AN - OPUS4-47305 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Falk, Florian A1 - Menneken, M. A1 - Stephan-Scherb, Christiane T1 - Real-time observation of high- temperature gas corrosion in dry and wet SO2-containing atmosphere N2 - Sulfur and water have a fundamental impact on the corrosion rate and potential failure of materials. It is therefore necessary to understand the mechanisms, rates, and potential means of transport, as well as the reactions of these elements with an alloy. This paper investigates the effect of water vapor in the initial stages of SO2 corrosion of an Fe-9Cr-0.5Mn model alloy at 650°C in situ under laboratory conditions using energy-dispersive x-ray diffraction analysis. Two separate experiments were run, one with a 99.5% Ar + 0.5% SO2 atmosphere and one with a 69.5% Ar + 0.5% SO2 + 30% H2O atmosphere. With a wet atmosphere, the alloy formed a scale with decreasing oxygen content towards the scale–alloy interface. Sulfides were identified above and below a (Fe, Cr)3O4 layer in the inner corrosion zone. In contrast to this, the overall scale growth was slower in a dry SO2 atmosphere. KW - Early oxidation KW - Early sulfidation KW - Ferritic steels PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-472844 UR - https://link.springer.com/article/10.1007/s11837-019-03335-9#enumeration DO - https://doi.org/10.1007/s11837-019-03335-9 SN - 1047-4838 SN - 1543-1851 VL - 71 SP - 1 EP - 6 PB - Springer CY - New York AN - OPUS4-47284 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Ronald A1 - Rogge, Andreas A1 - Thöns, S. A1 - Bismut, E. A1 - Straub, D. ED - Caspeele, Robby ED - Taerwe, Luc ED - Frangopol, Dan M. T1 - A sampling-based approach to identifying optimal inspection and repair strategies for offshore jacket structures N2 - Identifying optimal inspection and repair strategies for offshore jacket structures is a challenging task. We pre-sent an approach, which is based on recent developments in the field of risk-based operation and maintenance planning at the structural system level. The approach utilizes heuristics to define inspection and repair strate-gies at the system level and to reduce the search space of possible strategies. For each defined strategy, the expected service life cost of inspection, repair and failure is evaluated based on simulated inspection and re-pair histories. Subset simulation is applied to compute the conditional repair and failure probabilities required for this analysis. It also forms the basis for simulating inspection and repair histories. The strategy that mini-mizes the expected service life cost is the optimal one in the set of pre-selected strategies. The underlying condition and performance model accounts for the stochastic dependence among the deterioration states of the different structural elements and the structural redundancy. The approach is demonstrated in a case study considering a jacket-type frame. In this study, we essentially vary the inspection interval, the minimum num-ber of inspected components and the target reliability, and identify the combination that minimizes the ex-pected total service life cost. T2 - The sixth international symposium on life-cycle civil engineering (IALCCE 2018) CY - Ghent, Belgien DA - 28.10.2018 KW - Offshore steel structures KW - Fatigue KW - Reliability KW - Risk KW - Inspection planning PY - 2019 SN - 978-1-138-62633-1 SN - 978-1-315-22891-4 SP - 1081 EP - 1088 PB - Taylor & Francis Group CY - London AN - OPUS4-46434 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Minimum safety requirement for CGH2-pressure receptacles: 2nd FDIS ISO 17519 N2 - Der Vortrag fasst alle Bedenken sicherheitstechnischer Art zusammen, die den DIN bewogen haben, ein ISO-Projekt zu extrem großen Gas-/Wasserstofftransporteinheiten abzulehnen. Kernpunkt ist das mit dem Skope des Normprojektes durch Druck- und Volumenerhöhung gegenüber dem heutigen Stand der Technik erheblich angestiegene Konsequenzpotential. Gleichzeitig fehlt ein Ansatz, den von der Konsequenz bis zum kritischen Niveau einer Katastrophe abhängigen Zuverlässigkeitsanforderungen Rechnung zu tragen. N2 - The presentation summarizes all the safety concerns that have led DIN to reject an ISO project about extremely large gas/hydrogen transport units. The core point is the consequence potential, which has increased considerably with the scope of the standardization project in comparison with state of the art systems. At the same time, there is a lack of an approach to take into account the reliability requirements that depend on the consequences, at least up to the level of a catastrophe. T2 - Sitzung des NA 016 DIN-Normenausschuss Druckgasanlagen (NDG) Arbeitskreis Compositeflaschens mit Gästen aus den USA (Convenor) CY - DIN, Berlin, Germany DA - 10.01.2019 KW - Acceptance of a standard KW - Tube trailer KW - Pressure-volume-product KW - Catastrophic consequence KW - Safety goal PY - 2019 AN - OPUS4-47280 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - An, Biwen Annie A1 - Shen, Y. A1 - Voordouw, J. A1 - Voordouw, G. T1 - Halophilic methylotrophic methanogens may contribute to the high ammonium concentrations found in shale oil and shale gas reservoirs N2 - Flow-back and produced waters from shale gas and shale oil fields contain high ammonium, which can be formed by methanogenic degradation of methylamines into methane and ammonium. Methylamines are added to fracturing fluid to prevent clay swelling or can originate from metabolism of the osmolyte triglycinebetaine (GB). We analyzed field samples from a shale gas reservoir in the Duvernay Formation and from a shale oil reservoir in the Bakken formation in Canada to determine the origin of high ammonium. Fresh waters used to make fracturing fluid, early flow-back waters, and late flow back waters from the shale gas reservoir had increasing salinity of 0.01, 0.58, and 2.66 Meq of NaCl, respectively. Microbial community analyses reflected this fresh water to saline transition with halophilic taxa including Halomonas, Halanaerobium, and Methanohalophilus being increasingly present. Early and late flow-back waters had high ammonium concentrations of 32 and 15 mM, respectively. Such high concentrations had also been found in the Bakken produced waters. Enrichment cultures of Bakken produced waters in medium containing mono, di-, or trimethylamine, or triglycinebetaine (GB) converted these substrates into ammonium (up to 20 mM) and methane. The methylotrophic methanogen Methanohalophilus, which uses methylamines for its energy metabolism and uses GB as an osmolyte, was a dominant community member in these enrichments. Halanaerobium was also a dominant community member that metabolizes GB into trimethylamine, which is then metabolized further by Methanohalophilus. However, the micromolar concentrations of GB measured in shale reservoirs make them an unlikely source for the 1,000-fold higher ammonium concentrations in flow-back waters. This ammonium either originates directly from the reservoir or is formed from methylamines, which originate from the reservoir, or are added during the hydraulic fracturing process. These methylamines are then converted into ammonium and methane by halophilic methylotrophic methanogens, such as Methanohalophilus, present in flow-back waters. KW - Methanogen KW - Oil and gas industry KW - Shale KW - Halophile KW - Corrosion PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-474982 DO - https://doi.org/10.3389/fenrg.2019.00023 SN - 2296-598X VL - 7 SP - 1 EP - 13 PB - Frontiers Media CY - Lausanne AN - OPUS4-47498 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Liehr, Sascha A1 - Jäger, L. A. A1 - Karapanagiotis, Christos A1 - Münzenberger, Sven A1 - Kowarik, Stefan T1 - Real-time dynamic strain sensing in optical fibers using artificial neural networks N2 - We propose to use artificial neural networks (ANNs) for raw measurement data interpolation and signal shift computation and to demonstrate advantages for wavelength-scanning coherent optical time domain reflectometry (WS-COTDR) and dynamic strain distribution measurement along optical fibers. The ANNs are trained with synthetic data to predict signal shifts from wavelength scans. Domain adaptation to measurement data is achieved, and standard correlation algorithms are outperformed. First and foremost, the ANN reduces the data analysis time by more than two orders of magnitude, making it possible for the first time to predict strain in real-time applications using the WS-COTDR approach. Further, strain noise and linearity of the sensor response are improved, resulting in more accurate measurements. ANNs also perform better for low signal-to-noise measurement data, for a reduced length of correlation input (i.e., extended distance range), and for coarser sampling settings (i.e., extended strain scanning range). The general applicability is demonstrated for distributed measurement of ground movement along a dark fiber in a telecom cable. The presented ANN-based techniques can be employed to improve the performance of a wide range of correlation or interpolation problems in fiber sensing data analysis and beyond. KW - Distributed vibration sensing KW - Distributed acoustic sensing KW - Coherent optical time domain reflectometry KW - Optical fiber sensor KW - Artificial neural network KW - Real time measurement KW - Distributed strain sensing PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-474832 UR - https://www.osapublishing.org/oe/abstract.cfm?uri=oe-27-5-7405 DO - https://doi.org/10.1364/OE.27.007405 SN - 1094-4087 VL - 27 IS - 5 SP - 7405 EP - 7425 PB - Optical Society of America AN - OPUS4-47483 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Peláez, R.J. A1 - Rebollar, E. A1 - Serna, R. A1 - Acosta-Zepeda, C. A1 - Saavedra, P. A1 - Bonse, Jörn A1 - Haro-Poniatowski, E. T1 - Nanosecond laser-induced interference grating formation on silicon N2 - The formation of gratings on the surface of a silicon wafer by nanosecond laser irradiation through a phase mask using an ArF laser emitting at 193 nm is studied. The phase mask along with some focusing optics is capable to generate via interference a periodic intensity distribution, which can be used for surface patterning. The surface patterning strongly depends on the laser energy density and on the number of pulses, as revealed by atomic force microscopy (AFM). The results show that irradiation even with a single laser pulse produces periodic depth modulations on the surface. The spatial surface modulation is in the micrometer (1.7 µm) range while the depth modulation is in the nanometer regime (1–20 nm). With an increasing number of pulses (1–100), the depth modulation amplitude increases smoothly. Increasing the number of pulses further results in the progressive destruction of the grating, vanishing completely after ~5000 pulses. This evolution is also monitored in situ by measuring the intensity of the first order-diffracted probe beam and the behavior is in accordance with what is observed by AFM. Finally, we qualitatively explain the results invoking thermally induced effects in the melted Si: these physical processes involved are probably thermocapillary and/or Marangoni effects inducing material displacement as the surface melts. KW - Nanosecond laser irradiation KW - Silicon KW - Surface modification KW - Phase mask KW - Grating PY - 2019 UR - https://iopscience.iop.org/article/10.1088/1361-6463/ab0c5f DO - https://doi.org/10.1088/1361-6463/ab0c5f SN - 1361-6463 SN - 0022-3727 VL - 52 IS - 22 SP - 225302, 1 EP - 10 PB - IOP Publishing CY - Bristol, UK AN - OPUS4-47619 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Jan P. A1 - Krankenhagen, Rainer T1 - Optimizing thermographic testing of thick GFRP plates by assessing the real energy absorbed within the material N2 - Active thermography is a well suited non-destructive testing method for the challenging inspection of wind rotor blades. Since the GFRP structures are up to some centimetres thick, long pulse heating is required to provide an appropriate energy input into the structure. So far, no best practice exists to guarantee a reliable detection of deep-lying flaws. In this work, a step wedge specimen having a maximum thickness of 34mm is systematically investigated by experiment and well-matched simulations to assess the influence of the experimental parameters, like the absorbed energy, on thermal contrasts. Finally, a scheme to conduct full-scale test of a wind rotor blade in less than three hours is proposed. KW - Pulsed thermography KW - Wind rotor blade KW - GFRP PY - 2019 DO - https://doi.org/10.1016/j.compstruct.2019.02.027 SN - 0263-8223 VL - 215 SP - 60 EP - 68 PB - Elsevier CY - Amsterdam AN - OPUS4-47396 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Deep foundations for offshore wind turbines T1 - Cimentaciones profundas para aerogeneradores marinos N2 - This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures. The first lecture presents a brief introduction to the context and peculiarities of such foundations, and then focuses on the particular case of axially loaded piles. This part is most relevant for the relatively slender piles of the multi-pile substructures (i.e. jackets and tripods). A clear distinction between physical phenomenology and practical design is drawn here. The second lecture continues with the case of lateraly loaded offshore piles, which bears most relevance for the case of the monopile foundations. Here again, a clear separation between physical reality and design methods is intended. Finally, the last part of the second lecture introduces several advanced topics which lie outside the classical design approaches, namely the hydromechanical coupling effects (i.e. the excess pore-pressure generation around the monopiles), the cyclic pile fatigue and the so-called pile Setup (i.e. the time effects on the axial pile capacity). The relevance of the latter two topics is illustrated with experimental results from a field testing campaign on real large-scale piles. T2 - MASTERS COURSE 2019 CEDEX-UNED: MECÁNICA DEL SUELO E INGENIERÍA GEOTÉCNICA CY - Laboratorio de Geotecnia, CEDEX, Madrid, Spain DA - 25.03.2019 KW - Pile foundations KW - Offshore wind turbines KW - Physical phenomenology KW - Design methods KW - Numerical modelling KW - Physical testing PY - 2019 AN - OPUS4-47624 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Bäßler, Ralph T1 - Book review: Advanced ceramic and metallic coating and thin film materials for energy and environmental applications N2 - This book provides a state‐of‐the‐art overview on the processing, characterization, and modelling of metallic and ceramic materials used for energy and environmental applications. 17 scientists show a collection of current knowledge in 8 chapters. This book fulfills its intention to provide a reference book containing a collection of publications on thin films and coatings made of ceramic and metals used for energy and environmental applications. It covers a broad range of this topic and provides a comprehensive insight. Graduate and undergraduate students of materials science and mechanical engineering can find an overview on this topic to step in this interesting field of engineering. KW - Ceramic KW - Coating KW - Thin film KW - Energy PY - 2019 DO - https://doi.org/10.1002/maco.201970034 SN - 0947-5117 SN - 1521-4176 VL - 70 IS - 03 SP - 567 EP - 568 PB - WILEY-VCH Verlag GmbH & Co. KGaA CY - Weinheim AN - OPUS4-47517 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ghafafian, Carineh T1 - Restoring structural integrity - localized repairs for wind turbine rotor blades N2 - The effect of localized repairs on the mechanical properties and thus the lifespan of wind turbine rotor blade shells is examined. T2 - SAMPE Symposium 2019 CY - Dresden, Germany DA - 06.02.2019 KW - Fatigue KW - Glass fiber reinforced polymers KW - Lightweight materials KW - Sandwich KW - Wind turbine blades PY - 2019 AN - OPUS4-47443 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Palkowski, Carsten T1 - Dynamische Methode für die Energieeffizienzprüfung von Wärmepumpen N2 - Vorstellung der Dynamische Wärmepumpenprüfung beim DIN NA-044-00-06 AA T2 - Gremiunssitzung des NA 044-00-06 AA CY - Munich, Germany DA - 19.02.2019 KW - Wärmepumpen KW - Energieeffizienz KW - Dynamische Prüfung PY - 2019 AN - OPUS4-47414 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 49, Heft 1 T3 - Amts- und Mitteilungsblatt der BAM - 1/2019 KW - Anerkennungen KW - Zulassungen KW - Richtlinien KW - Festlegungen KW - Ausnahmegenehmigungen PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-477509 SN - 0340-7551 VL - 49 IS - 1 SP - 1 EP - 124 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-47750 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Wolff, Dietmar A1 - Bevilacqua, A. A1 - Carlsen, B. A1 - Chiguer, M. A1 - González-Espartero, A. A1 - Grahn, P. A1 - Saegusa, T. A1 - Sampson, M. A1 - Seelev, I. A1 - Wasinger, K. A1 - Waters, M. ED - González-Espartero (IAEA), A. T1 - Storing spent fuel until transport to reprocessing or disposal N2 - Spent fuel storage periods well beyond those originally foreseen are a reality. This publication offers several ideas and approaches that may be considered to address the increasingly longer storage times. The aim is to raise awareness, encourage dialogue and provide ideas on how to manage spent fuel. Key messages include the following: - Delays in reprocessing or disposal could result in spent fuel being stored for 100 years or longer. Safe, secure and effective storage of spent fuel manages fuel degradation while preserving future fuel cycle options. - Ageing management programmes apply engineering, operations and maintenance actions to ensure safety is maintained during storage, future handling and transport. - Site selection and facility and equipment design can significantly reduce the risks and costs of spent fuel storage over longer periods. - Spent fuel storage configurations can be selected to accommodate uncertain storage periods, to facilitate ageing management and to provide flexibility needed to accommodate the uncertainty of future end points, such as reprocessing or disposal. - By considering multiple licence renewals, regulatory frameworks can be designed to ensure safe storage until an acceptable end point is achieved. - Safety can be assured by maintaining shielding, containment, decay heat removal and criticality control. Navigating the complexity of societal beliefs and values, as well as political systems, has proven to be a greater challenge for the management of spent fuel than maintaining its safety and security or addressing the technical and economic aspects. - Sustainable spent fuel management requires policies and strategies to provide a clear, consistent and stable direction because they drive the need for spent fuel storage as well as the available options and timing for achieving an acceptable end point. Unless States address spent fuel reprocessing and disposal on a sufficient scale to accommodate their spent fuel discharges, then storage for longer and longer periods becomes the de facto end point — which is not considered to be consistent with the responsibility to protect human health and the environment. An effective, periodic licence renewal process can ensure effective ageing management and strong institutional control. Hence, spent fuel can be safely and securely stored for as long as it may be necessary until transport for reprocessing or disposal. However, the risks and costs of storing the growing inventory of spent fuel will continue to increase; and in the absence of an end point, it will eventually become a significant societal burden. KW - Storing spent fuel KW - Extended storing KW - Unknown storage duration PY - 2019 UR - https://www-pub.iaea.org/MTCD/publications/PDF/P1846_web.pdf SN - 978-92-0-100719-3 SN - 1995-7807 SP - 1 EP - 54 PB - IAEA Publishing Section CY - Wien, Austria AN - OPUS4-47693 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Palkowski, Carsten A1 - Zottl, A. A1 - Malenkovic, I. A1 - Simo, Anne T1 - Fixing efficiency values by unfixing compressor speed: Dynamic test method for heat pumps N2 - The growing market penetration of heat pumps indicates the need for a performance test method that better reflects the dynamic behavior of heat pumps. In this contribution, we developed and implemented a dynamic test method for the evaluation of the seasonal performance of heat pumps by means of laboratory testing. Current standards force the heat pump control inactive by fixing the compressor speed. In contrast, during dynamic testing, the compressor runs unfixed while the heat pump is subjected to a temperature profile. The profile consists of the different outdoor temperatures of a typical heating season based on the average European climate and also includes temperature changes to reflect the dynamic behavior of the heat pump. The seasonal performance can be directly obtained from the measured heating energy and electricity consumption making subsequent data interpolation and recalculation with correction factors obsolete. The method delivers results with high precision and high reproducibility and could be an appropriate method for a fair rating of heat pumps. KW - Heat pump KW - Dynamic test method KW - Seasonal performance factor KW - Variable frequency drive KW - Energy label PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-476944 DO - https://doi.org/10.3390/en12061045 SN - 1996-1073 VL - 12 IS - 6 SP - 1045, 1 EP - 16 PB - MDPI CY - Basel, Switzerland AN - OPUS4-47694 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -