TY - JOUR A1 - Shabir Mahr, Muhammad A1 - Hübert, Thomas A1 - Sabel, Martin A1 - Schartel, Bernhard A1 - Bahr, Horst A1 - Militz, H. T1 - Fire retardancy of sol-gel derived titania wood-inorganic composites JF - Journal of materials science N2 - Sol–gel technology was applied in tailoring novel wood-made-inorganic composites with improved thermal and fire properties. In practice, composites materials were prepared by impregnating pine sapwood wood with nano-scaled precursor solutions derived from titanium(IV) isopropoxide followed by a thermal curing process. Thermal and fire properties were evaluated by thermal analysis and cone calorimetry, whereas flammability was specified by oxygen index (LOI) and UL 94 test. Peak heat release rates were moderately reduced indicating fire retardance potential in terms of flame spread attributed to the appropriate protection layer action of the titania-based depositions. LOI (oxygen index) values of these composites were increased up to 38 vol.% in comparison to 23 vol.% for untreated wood. The flame retardancy performance depends on the fire scenario and is strongly influenced by wood loading and crackfree deposition of the titania layers inside the composite. PY - 2012 DO - https://doi.org/10.1007/s10853-012-6628-3 SN - 0022-2461 SN - 1573-4803 VL - 47 IS - 19 SP - 6849 EP - 6861 PB - Springer Science + Business Media B.V. CY - Norwell, Mass. AN - OPUS4-26235 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wawrzyn, Eliza A1 - Schartel, Bernhard A1 - Seefeldt, Henrik A1 - Karrasch, A1 - Jäger, Christian T1 - What reacts with what in bisphenol A polycarbonate/silicon rubber/bisphenol A bis(diphenyl phosphate) during pyrolysis and fire behavior? JF - Industrial & engineering chemistry research N2 - The pyrolysis and flame retardancy of a bisphenol A polycarbonate/silicon rubber/bisphenol A bis(diphenyl phosphate) (PC/SiR/BDP) blend were investigated and compared to those of PC/BDP and PC/SiR. The impact modifier SiR consists mainly of poly(dimethylsiloxane) (PDMS > 80 wt %). The pyrolysis of PC/SiR/BDP was studied by thermogravimetry (TG), TG–FTIR to analyze the evolved gases, and a Linkam hot stage cell within FTIR as well as 29Si NMR and 31P NMR to analyze the solid residue. The fire performance was determined by PCFC, LOI, UL 94, and a cone calorimeter under different external irradiations. The fire residues were studied by using ATR-FTIR as well as the additional binary systems PC + PDMS, PC + BDP, and BDP + PDMS, focusing on the specific chemical interactions. The decomposition pathways are revealed, focusing on the competing interaction between the components. Fire retardancy in PC/SiR/BDP is caused by both flame inhibition in the gas phase and inorganic-carbonaceous residue formation in the condensed phase. The PC/SiR/BDP does not work as well superimposing the PC/SiR and PC/BDP performances. PDMS reacts with PC and BDP, decreasing BDP's mode of action. Nevertheless, the flammability (LOI > 37%, UL 94 V-0) of PC/SiR/BDP equals the high level of PC/BDP. Indeed, SiR in PC/SiR/BDP is underlined as a promising impact modifier in flame-retarded PC/impact modifier blends as an alternative to highly flammable impact modifiers such as acrylonitrile–butadiene–styrene (ABS), taking into account that the chosen SiR leads to PC blends with a similar mechanical performance. KW - PC KW - BDP KW - PDMS KW - Flame retardancy KW - Flammability KW - Decomposition KW - Pyrolysis PY - 2012 DO - https://doi.org/10.1021/ie201908s SN - 0888-5885 SN - 1520-5045 VL - 51 IS - 3 SP - 1244 EP - 1255 PB - American Chemical Society CY - Washington, DC AN - OPUS4-25460 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wu, Guang Mei A1 - Schartel, Bernhard A1 - Kleemeier, M. A1 - Hartwig, A. T1 - Flammability of layered silicate epoxy nanocomposites combined with low-melting inorganic ceepree glass JF - Polymer engineering & science N2 - Tetraphenylphosphonium modified layered silicate epoxy nanocomposite (EP/TPPMMT) combined with low-melting silicate glass, Ceepree (CP) is investigated by thermal analysis, flammability tests and cone calorimeter at different heat fluxes. Adding CP and TPPMMT does not change the pyrolysis apart from increasing inorganic residue. The total heat evolved (THE) is changed insignificantly, as neither relevant additional carbonaceous charring nor flame inhibition occurs. However, flame retardancy is clearly observed due to an inorganic-carbonaceous surface protection layer. The peak heat released rate (PHRR) is reduced by around 32–42% when 5 wt% TPPMMT is added, and 51–63% when 10 wt% CP is added. PHRR reduction less than expected is observed when both additives are combined. The reduction is greater than that achieved by using TPPMMT but less than when only CP is used. The morphology of fire residue is investigated by scanning electron microscope on different length scales and turns out to be the key to understanding the efficiency of flame retardancy. The fire residue of EP/CP shows a layered structure, whereas separated columns limit the barrier properties for EP/5%TPPMMT on the micrometer scale. Columns dominating the fire residue structure of EP/5%TPPMMT/10%CP deteriorate the fire retardancy, whereas a more integral structure at the top of the residue causes the improvement over EP/5%TPPMMT. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers KW - Flame retardancy KW - Nanocomposites KW - Low melting glasses KW - Epoxy resin KW - Ceepree PY - 2012 DO - https://doi.org/10.1002/pen.22111 SN - 0032-3888 SN - 1548-2634 VL - 52 IS - 3 SP - 507 EP - 517 PB - Wiley CY - Hoboken, NY AN - OPUS4-25590 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bier, A.K. A1 - Bognitzki, M. A1 - Schmidt, A. A1 - Greiner, A. A1 - Gallo, Emanuela A1 - Klack, Patrick A1 - Schartel, Bernhard T1 - Synthesis, properties, and processing of new siloxane-substituted poly(p-xylylene) via CVD JF - Macromolecules N2 - The synthesis of a disiloxane-functionalized [2.2]paracyclophane and its polymerization to the corresponding siloxane-substituted poly(p-xylylene) via chemical vapor deposition (CVD) has been described. Because of the enhanced solubility of the siloxane substituted poly(p-xylylene) analysis of the molecular structure by NMR, molecular weight, and polydispersity by gel permeation chromatography (GPC), and processing by film casting as well as nanofiber formation by electrospinning was possible. Structural isomers were found by NMR which was expected due to the isomeric mixture of the precursor. High molecular weights at moderate polydispersities were found by GPC which was unexpected for a vapor phase deposition polymerization. The amorphous morphology in combination with a low glass transition temperature led to high elongation at break for the siloxane substituted poly(p-xylylene). Significant difference for the wetting versus water was found for as-deposited films, solution cast films, and nanofibers obtained by electrospinning with contact angles up to 135° close to superhydrophobic behavior. KW - Poly(p-xylylene) KW - Siloxane functionalized PPX KW - Chemical vapor deposition KW - Difunctionalized [2.2]paracyclophanes KW - Gorham process PY - 2012 DO - https://doi.org/10.1021/ma2021369 SN - 0024-9297 SN - 1520-5835 VL - 45 IS - 2 SP - 633 EP - 639 PB - American Chemical Society CY - Washington, DC AN - OPUS4-25466 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wu, Guang Mei A1 - Schartel, Bernhard A1 - Yu, D. A1 - Kleemeier, M. A1 - Hartwig, A. T1 - Synergistic fire retardancy in layered-silicate nanocomposite combined with low-melting phenysiloxane glass JF - Journal of fire sciences N2 - Tetraphenyl phosphonium-modified layered silicate (LS) and low-melting phenylsiloxane glass (G) are combined for more efficient halogen-free flame retardancy in epoxy resin (EP_LSG). Particularly, the peak heat release rate (PHRR) is decreased (by up to 60%), but levels off at additive concentrations ≥10 wt%. The performance of EP_LSG is compared to EP_LS and EP_G assuming an absolute and a relative flame retardancy effect, respectively, and based on the same amount of each filler and, alternatively, with EP_G containing the same overall amount of filler. EP_LSG behaves close to superposition but shows a strong tendency toward synergism due to a superior structural integrity of the fire residues. Apart from LS, adding G in particular is a promising approach when its content is ≤5 wt%, as is LSG for ≥10 wt%. KW - Low-melting glass KW - Layered silicate KW - Flame retardancy KW - Nanocomposites KW - Epoxy resin PY - 2012 DO - https://doi.org/10.1177/0734904111422417 SN - 0734-9041 SN - 1530-8049 VL - 30 IS - 1 SP - 69 EP - 87 PB - Sage CY - London AN - OPUS4-25359 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard A1 - Meyer-Plath, Asmus A1 - Dittrich, Bettina A1 - Petrov, Sergej A1 - Mülhaupt, R. A1 - Friedrich, C. A1 - Moseler, M. A1 - Hofmann, D. A1 - Wartig, K.-A. A1 - Tölle, F. A1 - Beckert, F. A1 - Schopp, S. A1 - Ratzsch, K. A1 - Mohamed, M. A1 - Walter, M. A1 - Kailer, A. A1 - Riedinger, B. A1 - Altstädt, V. A1 - Kerling, S. T1 - FUNgraphen - Vorstellung der Forschungsziele T2 - 4. Jahrestagung inno.CNT T2 - 4. Jahrestagung inno.CNT CY - Bayreuth, Germany DA - 2012-01-30 PY - 2012 AN - OPUS4-25613 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Thin fire protection coatings: Is there any alternative to intumescence? T2 - European coatings conference: Fire redardant coatings V T2 - European coatings conference: Fire redardant coatings V CY - Berlin, Germany DA - 2012-03-13 PY - 2012 AN - OPUS4-25612 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Towards Evidence-based Development of Flame Retarded Polymers T2 - 243th ACS National Meeting Spring 2012 T2 - 243th ACS National Meeting Spring 2012 CY - San Diego, CA, USA DA - 2012-03-25 PY - 2012 AN - OPUS4-25716 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wawrzyn, Eliza A1 - Schartel, Bernhard A1 - Ciesielski, M. A1 - Kretzschmar, B. A1 - Braun, Ulrike A1 - Döring, M. T1 - Are novel aryl phosphates competitors for bisphenol A bis(diphenyl phosphate) in halogen-free flame-retarded polycarbonate/acrylonitrile-butadiene-styrene blends? JF - European polymer journal N2 - The reactivity of the flame retardant and its decomposition temperature control the condensed-phase action in bisphenol A polycarbonate/acrylonitrile–butadiene–styrene/polytetrafluoroethylene (PC/ABSPTFE) blends. Thus, to increase charring in the condensed phase of PC/ABSPTFE + aryl phosphate, two halogen-free flame retardants were synthesized: 3,3,5-trimethylcyclohexylbisphenol bis(diphenyl phosphate) (TMC-BDP) and bisphenol A bis(diethyl phosphate) (BEP). Their performance is compared to bisphenol A bis(diphenyl phosphate) (BDP) in PC/ABSPTFE blend. The comprehensive study was carried out using thermogravimetry (TG); TG coupled with Fourier transform infrared spectrometer (TG-FTIR); the Underwriters Laboratory burning chamber (UL 94); limiting oxygen index (LOI); cone calorimeter at different irradiations; tensile, bending and heat distortion temperature tests; as well as rheological studies and differential scanning calorimeter (DSC). With respect to pyrolysis, TMC-BDP works as well as BDP in the PC/ABSPTFE blend by enhancing the cross-linking of PC, whereas BEP shows worse performance because it prefers cross-linking with itself rather than with PC. As to its fire behavior, PC/ABSPTFE + TMC-BDP presents results very similar to PC/ABSPTFE + BDP; the blend PC/ABSPTFE + BEP shows lower flame inhibition and higher total heat evolved (THE). The UL 94 for the materials with TMC-BDP and BDP improved from HB to V0 for specimens of 3.2 mm thickness compared to PC/ABSPTFE and PC/ABSPTFE + BEP; the LOI increased from around 24% up to around 28%, respectively. BEP works as the strongest plasticizer in PC/ABSPTFE, whereas the blends with TMC-BDP and BDP present the same rheological properties. PC/ABSPTFE + TMC-BDP exhibits the best mechanical properties among all flame-retarded blends. KW - Polycarbonate (PC) KW - Aryl phosphate KW - Flame retardancy KW - Pyrolysis KW - PC/ABS PY - 2012 DO - https://doi.org/10.1016/j.eurpolymj.2012.06.015 SN - 0014-3057 SN - 1873-1945 VL - 48 IS - 9 SP - 1561 EP - 1574 PB - Elsevier CY - Oxford AN - OPUS4-26292 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kempel, Florian A1 - Schartel, Bernhard A1 - Linteris, G.T. A1 - Stoliarov, S.I. A1 - Lyon, R.E. A1 - Walters, R.N. A1 - Hofmann-Böllinghaus, Anja T1 - Prediction of the mass loss rate of polymer materials: Impact of residue formation JF - Combustion and flame N2 - Two different numerical simulation tools, Fire Dynamic Simulator (FDS) and ThermaKin, are investigated with respect to their capability to predict the mass loss rate of polymer materials exposed to different fires. For validation, gasification apparatus and cone calorimeter tests are conducted. The main focus is on the influence of residue formation. Therefore, poly (butylene terephthalate) (PBT) and PBT reinforced with glass fibres (PBT-GF) are investigated and compared. PBT decomposes almost completely, while PBT-GF forms residue. The materials are characterised in order to provide suitable input parameters. Additionally the total incident heat flux to the sample is measured. With accurate input parameters, FDS and ThermaKin predicted the pyrolysis behaviour of PBT very well. Only some limitations are identified regarding the residue-forming PBT-GF. Both numerical simulation tools demonstrate a high value regarding the assessment of parameters' relative impacts and thus the evaluation of optimisation routes in polymer and composite development. KW - Polymer KW - Pyrolysis simulation KW - Residue formation KW - Fire dynamics simulator (FDS) KW - ThermKin PY - 2012 DO - https://doi.org/10.1016/j.combustflame.2012.03.012 SN - 0010-2180 SN - 1556-2921 VL - 159 IS - 9 SP - 2974 EP - 2984 PB - Elsevier CY - New York, NY AN - OPUS4-26382 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schartel, Bernhard T1 - Towards evidence-based development of flame retarded polymers JF - 243rd National ACS meeting - Spring 2012 (Proceedings) T2 - 243rd National ACS meeting - Spring 2012 CY - San Diego, CA, USA DA - 2012-03-25 KW - Flame retardancy KW - Halogen-free KW - Flame retardancy mechanism KW - Fire property assessment PY - 2012 SN - 978-0-8412-2727-9 SN - 1550-6703 N1 - Serientitel: PMSE Preprints – Series title: PMSE Preprints VL - 243 SP - 38-PMSE PB - Amer Chemical SOC CY - Washington, USA AN - OPUS4-26381 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brehme, Sven A1 - Köppl, T. A1 - Schartel, Bernhard A1 - Fischer, O. A1 - Altstädt, V. A1 - Pospiech, D. A1 - Döring, M. T1 - Phosphorus polyester - an alternative to low-molecular-weight flame retardants in poly(butylene terephthalate)? JF - Macromolecular chemistry and physics N2 - Pyrolysis, fire behaviour and mechanical properties of a blend of poly(butylene terephthalate) (PBT) with a phosphorus polyester (PET-P-DOPO) are investigated and compared with PBT/aluminium diethylphosphinate (AlPi-Et) composites. The PBT/PET-P-DOPO is immiscible and exhibits gas-phase and condensed-phase activity, whereas AlPi-Et in PBT results mainly in flame inhibition. Only higher loadings of AlPi-Et yield significant condensed-phase activity. Using the same phosphorus content, PBT/PET-P-DOPO and PBT/AlPi-Et exhibit similar reductions in fire load (22%) and flame spread (17% assessed by fire growth rate, FIGRA), compared with PBT. In contrast to AlPi-Et, the addition of PET-P-DOPO does not decrease the tensile strength of PBT. Thus, PET-P-DOPO is an interesting alternative to low-molecular-weight flame retardants. KW - Aluminium phosphinate KW - Blends KW - 9, 10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide KW - Flame retardance KW - Polyesters PY - 2012 DO - https://doi.org/10.1002/macp.201200072 SN - 1022-1352 SN - 1521-3935 VL - 213 IS - 22 SP - 2386 EP - 2397 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-26982 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Schartel, Bernhard A1 - Richter, K. H. A1 - Böhning, Martin ED - Morgan, A. B. ED - Wilkie, C. A. ED - Nelson, G. L. T1 - Synergistic use of talc in halogen-free flame retarded polycarbonate/Acrylonitrile-butadiene-styrene blends T2 - Fire and polymers VI: New advances in flame retardant chemistry and science N2 - Pyrolysis, flammability, fire behavior, melt viscosity, and gas diffusion of bisphenol A polycarbonate/acrylonitrile-butadiene-styrene (PC/ABS) were investigated, with bisphenol A bis(diphenyl phosphate) (BDP), with 10 wt.% talc and with BDP in combination with 5, 10 and 20 wt.% talc, respectively. Compared to PC/ABS, PC/ABS + BDP results in an increased decomposition temperature of PC, a higher char yield, a significantly increased LOI, a V-0 classification in UL 94, a reduced peak heat release rate (pHRR), and a reduced total heat release (THR) in the cone calorimeter. This efficient flame retardancy is due to mechanisms in both the gas and condensed phases. PC/ABS + 10 wt.% talc shows a decrease in the PC decomposition temperature. The fire behavior is improved in part compared to PC/ABS, with an increased LOI and reduced pHRR. PC/ABS + BDP + 10 wt.% talc shows a strong synergism in LOI, a V-0 classification, and a decrease in pHRR, whereas THR is slightly increased compared to PC/ABS + BDP. Talc decreases the gas diffusion and enhances the flow limit for low shear rates, both of which influence the pyrolysis and flammability results. Further, talc improves the protection properties of the fire residues. Nevertheless it also partly suppresses flame inhibition and the charring effect of BDP. The synergism between BDP and talc in LOI is obtained even for low talc loadings in PC/ABS + BDP + talc, whereas for higher loadings saturation is observed. KW - Flame retardancy KW - PC/ABS KW - Aryl phosphate KW - Talc PY - 2012 SN - 978-0-8412-2780-4 DO - https://doi.org/10.1021/bk-2012-1118.ch002 N1 - Serientitel: ACS Symposium Series – Series title: ACS Symposium Series VL - 1118 IS - Chapter 2 SP - 15 EP - 36 PB - Oxford University Press AN - OPUS4-27563 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wu, Guang Mei A1 - Schartel, Bernhard A1 - Bahr, Horst A1 - Kleemeier, M. A1 - Yu, D. A1 - Hartwig, A. T1 - Experimental and quantitative assessment of flame retardancy by the shielding effect in layered silicate epoxy nanocomposites JF - Combustion and flame N2 - A quantitative experimental assessment of flame retardancy by the heat shielding in epoxy layered silicate nanocomposite (EP/TPPMMT) is presented. Online heat flux measurements and temperature monitoring within the specimen are performed during the burning in the cone calorimeter. For EP the surface layer equals a pyrolysis front. The reradiation by the hot surface corresponds to the fourth power of the pyrolysis temperature. The surface reradiation (around 10 kW m-2) is thus fairly invariable over burning time and different external heat fluxes. Further, the thermal feedback of the flame is approximated to 20 kW m-2 for both EP and EP/TPPMMT and invariable over different irradiations. Thus the net heat fluxes transformed to the fuel release rate within the pyrolysis front of EP are increased to 45–80 kW m-2 when irradiations of 35–70 kW m-2 are applied. For a residue-forming EP/TPPMMT the surface temperature and thus the reradiation (42–68 kW m-2) crucially increases compared to EP and with increasing irradiation. The net heat fluxes are reduced to 13–22 kW m-2 accordingly. This quantitative assessment of the heat shielding in EP/TPPMMT goes along with proportional and consistent improvement in the fire performance, such as the pyrolysis front velocity, the heat release rate (HRR) characteristics such as averaged and quasi-steady-state HRR and the peak HRR (PHRR). The heat shielding is proven to be the only major flame retardancy effect occurring in nanocomposites based on non-charring polymers. KW - Nanocomposites KW - Heat shielding KW - Flame retardancy KW - Shielding effect PY - 2012 DO - https://doi.org/10.1016/j.combustflame.2012.07.003 SN - 0010-2180 SN - 1556-2921 VL - 159 IS - 12 SP - 3616 EP - 3623 PB - Elsevier CY - New York, NY AN - OPUS4-26841 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Shabir Mahr, Muhammad A1 - Hübert, Thomas A1 - Schartel, Bernhard A1 - Bahr, Horst A1 - Sabel, Martin A1 - Militz, H. T1 - Fire retardancy effects in single and double layered sol-gel derived TiO2 and SiO2-wood composites JF - Journal of sol gel science and technology N2 - Sol–gel derived TiO2 and SiO2-wood inorganic composites are prepared by direct vacuum infiltration of silicon and titanium alkoxide based precursors in pine sapwood in one or two cycles followed by a controlled thermal curing process. The resulting flame retardancy effect is investigated under two different fire scenarios using cone calorimetry and oxygen index (LOI). Heat release rates (HRR) especially the values for the second peak, are reduced moderately for all single layered composites. This effect is more pronounced for double layered composites where HRR was reduced up to 40 % showing flame retardancy potential in developing fires. Beside this, smoke release was lowered up to 72 % indicating that these systems had less fire hazards compared to untreated wood, whereas no meaningful improvement is realized in terms of fire load (total heat evolved) and initial HRR increase. However impressively, the LOI of the composites were increased up to 41 vol% in comparison to 23 vol% for untreated wood displaying a remarkable flame retardancy against reaction to a small flame. An approximate linear interdependence among the fire properties and the material loading as well as fire residue was observed. A residual protection layer mechanism is proposed improving the residue properties for the investigated composites. KW - Wood KW - Sol-gel KW - Composite materials KW - Cone calorimeter KW - Fire retardance KW - Flammability PY - 2012 DO - https://doi.org/10.1007/s10971-012-2877-5 SN - 0928-0707 SN - 1573-4846 VL - 64 IS - 2 SP - 452 EP - 464 PB - Kluwer Academic Publ. CY - Dordrecht AN - OPUS4-27618 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lorenzetti, A. A1 - Modesti, M. A1 - Gallo, Emanuela A1 - Schartel, Bernhard A1 - Besco, S. A1 - Roso, M. T1 - Synthesis of phosphinated polyurethane foams with improved fire behaviour JF - Polymer degradation and stability N2 - Both alkylphosphinates and inorganic phosphinates (based on sodium, calcium, magnesium or zinc) have been recently proposed as flame retardants for polyesters, polyamides and polyurethane foams as well. The main aim of this work was to compare the flame retardant effectiveness of inorganic (already proofed in PU foams) and organic phosphinates in PU foams which have never been used in polyurethane (PU) foams. The thermal stability in nitrogen and air as well as limiting oxygen index and cone calorimeter behaviour have been studied to assess the effectiveness of such flame retardants in PU foams. The results obtained showed that both inorganic and organic phosphinates are effective in enhancing fire behaviour of PU foams since they improve thermal stability, LOI and fire performance. Cone calorimetry highlighted the flame inhibition action in the gas phase due to the release of phosphorus-containing molecules. The better results obtained for inorganic phosphinate are probably related to the better quality of the char layer developed during burning, but may also be related to the higher phosphorus content of such flame retardant with respect the other ones. It was also verified that both inorganic and organic phosphinate containing N-synergic compound showed a fuel dilution effect, deriving from water and/or ammonia release in the gas phase. KW - Phosphinate KW - Polyurethane foam KW - Flame retardancy KW - Fire behaviour PY - 2012 DO - https://doi.org/10.1016/j.polymdegradstab.2012.07.026 SN - 0141-3910 SN - 1873-2321 VL - 97 IS - 11 SP - 2364 EP - 2369 PB - Applied Science Publ. CY - London AN - OPUS4-26735 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Fire Retardant Composites: A Journey from Nano to Intermediate Scale T2 - Trends im Brandschutz und innovative Flammschutzmittel bei Kunststoffen T2 - Trends im Brandschutz und innovative Flammschutzmittel bei Kunststoffen CY - Würzburg, Germany DA - 2012-05-23 PY - 2012 AN - OPUS4-26489 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Nanotechnologie hält Einzug im Flammschutz T2 - Fachtagung Nano-Additive T2 - Fachtagung Nano-Additive CY - Berlin, Germany DA - 2012-11-19 PY - 2012 AN - OPUS4-29788 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hörold, Andreas A1 - Schartel, Bernhard A1 - Trappe, Volker A1 - Korzen, Manfred A1 - Naumann, Maurice T1 - Structural integrity in fire: an intermediate-scale approach T2 - ECCM15 - 15th European conference on composite materials (Proceedings) T2 - ECCM15 - 15th European conference on composite materials CY - Venice, Italy DA - 2012-06-24 KW - Intermediate-scale test method KW - Structural integrity investigation KW - Fully developed fire KW - Carbon fibre reinforced plastics CFRP PY - 2012 SN - 978-88-88785-33-2 SP - 1 EP - 8(?) AN - OPUS4-26380 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Despinasse, Marie-Claire A1 - Schartel, Bernhard T1 - Influence of the structure of aryl phosphates on the flame retardancy of polycarbonate/acrylonitrile-butadiene-styrene JF - Polymer degradation and stability N2 - The impact of the chemical structure of four different aryl bisphosphates on the flame retardancy of bisphenol A polycarbonate/acrylonitrile–butadiene–styrene blends (PC/ABS) was investigated. The impact of the bridging unit was studied, by comparing bisphenol A bis(diphenyl phosphate) BDP with biphenyl bis(diphenyl phosphate) BBDP and hydroquinone bis(diphenyl phosphate) HDP; as well as the influence of an aromatic substitution by comparing BBDP with biphenyl bis (di-2,6-xylyl phosphate) BBXP. The blends were investigated in terms of pyrolysis (thermogravimetry TG, TG coupled with Fourier transformed infrared spectroscopy (FTIR) and mass spectrometry (MS)) and fire performance (cone calorimeter, LOI, UL 94). The decomposition temperature of the flame retardant is a main parameter enabling a condensed phase interaction with PC decomposition products. The phosphate esters reacting with phenolic groups during pyrolysis were shown to increase cross-linking and reduce the hydrolysis/alcoholysis of the carbonate group. Variation of the aromatic substitution with the use of biphenyl bis (di-2,6-xylyl phosphate) led to reduced performance, highlighting the importance of the reactivity of the flame retardant with the decomposing PC. KW - Bisphenol A polycarbonate/acrylonitrile–butadiene–styrene (PC/ABS) KW - Flame retardancy KW - Flammability KW - Phosphate esters KW - Pyrolysis PY - 2012 DO - https://doi.org/10.1016/j.polymdegradstab.2012.07.005 SN - 0141-3910 SN - 1873-2321 VL - 97 IS - 12 SP - 2571 EP - 2580 PB - Applied Science Publ. CY - London AN - OPUS4-26969 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sturm, Heinz A1 - Schartel, Bernhard A1 - Weiß, André A1 - Braun, Ulrike T1 - SEM/EDX: Advanced investigation of structured fire residues and residue formation JF - Polymer testing N2 - Heterogeneous, gradual or structured morphology of fire residues plays an important role in fire retardancy of polymers. A scanning electron microscope with an attached energy dispersive X-ray spectrometer (SEM/EDX) is highlighted as a powerful tool for the advanced characterization of such complex fire residues, since it offers high resolution in combination with both good depth of field and analysis of chemical composition. Two examples are presented: First, comprehensive SEM/EDX investigation on a complex structured fire residue of glass fibre reinforced polyamide 6,6 (PA 66-GF) flame retarded by diethylaluminium phosphinate, melamine polyphosphate and some zinc borate. A multilayered surface crust (thickness ~ 24 µm) covers a rather hollow area stabilized by GF glued together. The resulting efficient thermal insulation results in self-extinguishing before pyrolysis is completed, even under forced-flaming combustion. Second, sophisticated, quasi online SEM/EDX imaging of the formation of residual protection layer in layered silicate epoxy resin nanocomposites (LSEC). Burning specimens were quenched in liquid nitrogen for subsequent analyses. Different zones were distinguished in the condensed phase characterized by distinct processes such as melting and ablation of organic material, as well as agglomeration, depletion, exfoliation and reorientation of the LS. KW - Fire residue KW - SEM/EDX KW - Fire retardancy KW - PA 66 KW - Layered silicate KW - Diethylaluminium phosphinate PY - 2012 DO - https://doi.org/10.1016/j.polymertesting.2012.03.005 SN - 0142-9418 VL - 31 IS - 5 SP - 606 EP - 619 PB - Elsevier Science CY - Amsterdam [u.a.] AN - OPUS4-25802 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Köppl, T. A1 - Brehme, Sven A1 - Wolff-Fabris, F. A1 - Altstädt, V. A1 - Schartel, Bernhard A1 - Döring, M. T1 - Structure-property relationships of halogen-free flame-retarded poly(butylene terephthalate) and glass fiber reinforced PBT JF - Journal of applied polymer science N2 - Flame retardancy for thermoplastics is a challenging task where chemists and engineers work together to find solutions to improve the burning behavior without strongly influencing other key properties of the material. In this work, the halogen-free additives aluminum diethylphosphinate (AlPi-Et) and a mixture of aluminum phosphinate (AlPi) and resorcinol-bis(di-2,6-xylyl phosphate) (AlPi-H + RXP) are employed in neat and reinforced poly(butylene terephthalate) (PBT), and the morphology, mechanical performance, rheological behavior, and flammability of these materials are compared. Both additives show submicron dimensions but differ in terms of particle and agglomerate sizes und shapes. The overall mechanical performance of the PBT flame-retarded with AlPi-Et is lower than that with AlPi-H-RXP, due to the presence of larger agglomerates. Moreover, the flow behavior of the AlPi-Et/PBT materials is dramatically changed as the larger rod-like primary particles build a percolation threshold. In terms of flammability, both additives perform similar in the UL 94 test and under forced-flaming combustion. Nevertheless, AlPi-Et performs better than AlPi-H + RXP in the LOI test. The concentration required to achieve acceptable flame retardancy ranges above 15 wt %. KW - Polyesters KW - Fibers KW - Morphology KW - Structure–property relations KW - Flame retardance PY - 2012 DO - https://doi.org/10.1002/app.34910 SN - 0021-8995 SN - 1097-4628 VL - 124 IS - 1 SP - 9 EP - 18 PB - Wiley InterScience CY - Hoboken, NJ AN - OPUS4-25253 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schartel, Bernhard A1 - Beck, Uwe A1 - Bahr, Horst A1 - Hertwig, Andreas A1 - Knoll, Uta A1 - Weise, Matthias T1 - Sub-micrometre coatings as an infrared mirror: a new route to flame retardancy JF - Fire and materials N2 - Most of the polymeric materials used are easy to ignite and show extensive flame spread along their surfaces. Apart from extensive heat release rates, their short time to ignition (tig), in particular, is a key fire hazard. Preventing ignition eliminates fire hazards completely. Protection layers that shift tig by more than an order of magnitude are powerful flame retardancy approaches presenting an alternative to the usual flame retardancy concepts. Coatings are proposed that consist of a three-layer system to ensure adhesion to the substrate, acting as an infrared (IR) mirror and protecting against oxidation. The IR-mirror layer stack is realised by physical vapour deposition in the sub-micrometre (<1 µm) range, reducing heat absorption by up to an order of magnitude. Not only is the ease of ignition diminished (tig is increased by several minutes), the flame spread and fire growth indices are also remarkably reduced to as little as 1/10 of the values of the uncoated polymers open for further optimization. Sub-micrometre thin IR-mirror coatings yielding surface absorptivity <0.1 are proposed as a novel and innovative flame retardancy approach. KW - Coating KW - Fire protection KW - Physical vapour deposition (PVD) KW - IR mirror KW - Ignition PY - 2012 DO - https://doi.org/10.1002/fam.1122 SN - 0308-0501 SN - 1099-1018 VL - 36 IS - 8 SP - 671 EP - 677 PB - Heyden CY - London AN - OPUS4-27210 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -