TY - GEN ED - Rockland, Ulrike T1 - Jahresbericht 2010 T1 - Annual report 2010 T3 - BAM Reports/Jahresberichte - 2010 PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-4535 SN - 0934-9456 N1 - Volltext (PDF) in deutsch und englisch - Full text (PDF) in German and English VL - 2010 SP - 1 EP - 102 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-453 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Zoëga, Andreas T1 - Spannungsabhängigkeit elastischer Wellen in Beton N2 - Beton, einer der vielseitigsten und meist-verbreitetsten Baustoffe, verdankt diese Popularität seiner hohen Druckfestigkeit bei gleichzeitig geringen Kosten auf der einen Seite sowie seiner hohen Flexibilität durch die Möglichkeit der fast beliebigen Formgebung von lastabtragenden Elementen und Bauteilen auf der anderen Seite. Die weltweit verbreiteten Betonbauwerke altern und drängen die zerstörungsfreie Prüfung dazu, Prüfmethoden für eine effektive Zustandsbewertung von im Betrieb befindlichen Betonbauwerken zur Verfügung zu stellen. Für viele in anderen zerstörungsfreien Prüfbereichen alltägliche Anwendungen stellt Beton aufgrund der Heterogenität des Verbundwerkstoffs mit seinem nichtlinearen Spannungs-Dehnungs-Verhalten eine Herausforderung dar. Mit steigender Spannung nehmen die nichtlinearen Eigenschaften noch zu und können - z. B. durch die sich in Abhängigkeit von der Belastungsrichtung bildenden Mikrorisse - zu einer anisotropen Ausbildung von Eigenschaften führen, welche u. a. mit elastischen Wellen in Wechselwirkung treten. Bisherige Prüfaufgaben an Beton beschränken sich auf Bereiche, bei denen die elastischen Wellen ein lineares Verhalten aufweisen und sind daher nicht uneingeschränkt anwendbar. Gerade der Zusammenhang von Spannungszustand und Anisotropie zeigt eindeutige nichtlineare Effekte auf die Eigenschaften elastischer Wellen. Diese Eigenschaftsänderungen von elastischen Wellen sollen in dieser Arbeit anhand der Schallgeschwindigkeit erörtert werden. Neben einer Beobachtung und Dokumentation der auftretenden Effekte werden die Ursachen und Wirkmechanismen, die zu einer Schallgeschwindigkeitsänderung unter einer Druckbelastung führen, untersucht. In einem Vorversuch wurden Wellen unterschiedlichen Typs, Frequenz, Polarisation und Ausbreitungsrichtung auf ihre Sensitivität gegenüber einer Belastung miteinander verglichen. Hierbei stellte sich die Oberflächenwelle als die belastungsempfindlichste heraus und wird in dieser Arbeit für die Beschreibung der spannungsabhängigen Eigenschaftsänderungen von elastischen Wellen bevorzugt verwendet. Die für diese Versuchsserie erstellten Versuchsaufbauten und die verwendeten Oberflächenwellen erlaubten eine beliebige Orientierung der Messrichtung in Bezug zur Lastrichtung. Die Änderung der Schallgeschwindigkeit konnte damit in Richtungsabhängigkeit verfolgt und anisotropes Verhalten beobachtet werden. Ultraschallwellen sind für Untersuchungen an Beton die am häufigsten verwendeten; infolgedessen wurde zum Vergleich parallel mit Ultraschallwellen unterschiedlicher Frequenzen gemessen. Als Ergebnis aus der Versuchsserie konnte der Auslastungs- und Schädigungsgrad des Betons nachvollzogen und damit die Änderung der Schallgeschwindigkeit in Abhängigkeit von der aufgebrachten Last für eine sichere Bruchvorhersage verwendet werden. Mit wachsender Belastung stieg dabei die Schallgeschwindigkeit an, dieser Anstieg verlangsamte sich und ging im Bereich zwischen 50-80 % der Bruchlast in eine zunehmende Schallgeschwindigkeitsreduktion über. Der größte Schallgeschwindigkeitszuwachs konnte zu Beginn in Lastrichtung beobachtet werden, während die größte Schallgeschwindigkeitsreduktion in orthogonaler Richtung kurz vor dem Bruch stattfand. Der bei geringer Belastung (linear-elastischer Bereich) besonders deutliche Schallgeschwindigkeitsanstieg kann mithilfe der Akustoelastizität erklärt werden. Der sich vermindernde Anstieg und die Schallgeschwindigkeitsreduktion ließen sich experimentell auf die Mikrorissentstehung und das Mikrorisswachstum innerhalb des Betons zurückführen. Des Weiteren konnte gezeigt werden, dass sich die Schallgeschwindigkeit bei einer Wiederbelastung von der bei einer Erstbelastung unterscheidet, dieser Unterschied sich bei einer höheren Vorbelastung vergrößert, die Anzahl der vorangegangenen Belastungen einen Einfluss hat und eine Überlastung sich besonders deutlich in einer Schallgeschwindigkeitsminderung niederschlägt. Bei den Schallgeschwindigkeitsänderungen konnte ebenso eine zeitabhängige Komponente beobachtet werden. Die typischen Kurvenverläufe der Schallgeschwindigkeit über der Spannung konnten ebenso an Probekörpern mit anderen Betonrezepturen sowie an bewehrten Probekörpern aufgezeichnet werden. Die spannungsabhängige Änderung der Geschwindigkeit von elastischen Wellen in Beton ist ein nicht zu vernachlässigender Effekt, welcher für Prüfverfahren zur Inspektion von bestehenden Gebäuden in Betracht gezogen werden kann. Ein Verständnis für die Ursachen der belastungs- bzw. zerstörungsgradabhängigen Geschwindigkeitsänderung der elastischen Wellen in Beton ebnet den Weg zur Entwicklung und Etablierung neuer Prüfmethoden, mit deren Hilfe vor Ort und zerstörungsfrei der Auslastungs- und Schädigungsgrad einer Betonstruktur bestimmt werden kann. N2 - Concrete is one of the most widely used construction materials. Concrete owes this popularity to its high compressive strength, low costs and the flexibility of being cast in the form of customized structural elements and load-bearing members. The many concrete structures around the world are aging, urging the NDT community to develop testing tools for effective inspection of in-service concrete structures. Concrete poses a challenge to the application of standard NDT techniques. Concrete is a multi-phase heterogeneous material with a nonlinear stress-strain behavior. Loading and the resulting damage (i.e., microcracking) increase the non-linearity and may induce anisotropy in concrete. As a result, many of the common wave propagation-based NDT methods relying on linear elastic theory are no longer applicable. The main objective of this study is to investigate the stress-induced changes in the velocity of elastic waves in concrete under uniaxial compression. The underlying mechanisms of the observed effects have been also investigated here. A preliminary experiment was conducted to study the influence of the type, frequency, polarization, and propagation direction of elastic waves on the stress-induced velocity changes. The velocity of sonic surface waves (Rayleigh waves) demonstrated the highest sensitivity and therefore, much of this work is focused on the stress-induced changes in surface wave propagation characteristics. The test setup allowed measuring the surface wave velocities along various directions with respect to the loading direction and therefore, the direction-dependency of the surface wave velocity measurements was also investigated. Standard ultrasonic testing of various frequencies was also conducted and the results were compared to those from sonic surface wave measurements. Sonic surface wave velocities were found to be highly stress- and damage-dependent. Application of stress results in an initial sharp increase in surface wave velocity. Increasing the stress, the wave velocities continue to increase, however, the rate of increase decreases for stress levels between 50% and 80% of the failure stress, after which the velocities start rapidly to decrease. The sharpest increase was recorded in the direction of the loading, while the velocities decreased the fastest in the perpendicular direction. The sharp initial increase in wave velocities (within the elastic region) can be explained by acoustoelastic effects. The initiation and development of microcracks within concrete result in the observed velocitystress relationship beyond the elastic region. The test specimens were generally loaded in several load cycles and wave velocities were measured during both loading and unloading phases. It was found that the load history has a major effect on the velocity measurements. For previously loaded specimens, a notable difference between the velocity measurements during unloading and reloading was recorded. The higher the maximum previous load, the larger was the difference. Also, overloading the specimens resulted in a very large loss in surface wave velocities. Similar qualitative velocitystress relationships were obtained for a number of different concrete mixes as well as the reinforced concrete. Stress-dependency of elastic wave velocities in concrete is an important effect, which needs to be taken into account for in-situ measurements of in-service structural elements. Understanding and establishing the stress- and –damage dependency of wave velocities in concrete paves the way for developing new NDT techniques, which can be used to nondestructively estimate the in-situ stress and damage state of concrete. T3 - BAM Dissertationsreihe - 76 KW - Beton KW - Mikrorisse KW - Oberflächenwellen KW - Schallgeschwindigkeit KW - Spannungsabhängigkeit KW - Akustoelastizität KW - Richtungsabhängigkeit KW - elastische Wellen KW - Belastung PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-820 SN - 978-3-9814281-6-2 SN - 1613-4249 VL - 76 SP - 1 EP - 175 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-82 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Stoppel, Markus T1 - Differenzpotentialfeldmessung in der automatisierten Prüfung von Stahlbetonbauteilen N2 - Die Potentialfeldmessung ist eines der wichtigsten zerstörungsfreien Prüfverfahren für die Zustandsbewertung von Stahlbetonbauteilen. Mit dieser Methode kann eine ortsabhängige Wahrscheinlichkeit für aktive, chloridinduzierte Bewehrungskorrosion bestimmt werden. Bei der konventionellen Anwendung wird über ein langes Schleppkabel eine Verbindung zwischen einem Messgerät und der Bewehrung hergestellt. Eine Interpretation der Messergebnisse wird anhand der absoluten Potentialwerte durchgeführt. Die Zuordnung zu aktiven oder passiven Zustanden der Bewehrung ist dabei nicht eindeutig. Eine zuverlässigere Methode der Bewertung des Korrosionspotentials ist jedoch die Bestimmung der Gradienten der Messspannungen. Das vorrangige Ziel dieser Arbeit ist es, die Potentialfeldmessung zu einem vollkommen zerstörungsfreien Differenzpotentialfeldmessverfahren (DP-Messung) weiter zu entwickeln, mit dem die Potentialgradienten direkt gemessen werden und bei dem auf die permanente Ankoppelung an die Bewehrung verzichtet werden kann. Die Arbeit fasst die Entwicklungsschritte zusammen und definiert die Bewertungskriterien für die DP-Messung, die die Qualität der Interpretation verbessern. Anhand der neu definierten Gradientenbreite wird aufgezeigt, wie die Detektionswahrscheinlichkeit für korrosionsaktive Bereiche erhöht wird. Es wird gezeigt, wie die automatisierte Kombination des Verfahrens mit großflächigen Messungen des Feuchtegehalts und der Betondeckung zu einer zuverlässigeren Zustandsbewertung führt. N2 - The half-cell potential test is one of the most important non-destructive testing techniques used for condition evaluation of reinforced concrete structures. This method gives the probability of chloride-induced corrosion in steel reinforcing rebars. The conventional approach involves exposing a rebar and using a long wire to connect the measurement device to the rebar. An interpretation of the measurement results is carried out based on the absolute potential values. The assignment to active or passive states of the reinforcement is not unique. However, it has been recently found that the gradient of the measured potentials provides a more reliable assessment of the corrosion potential of reinforcements. The primary objective of this work was to enhance the potential mapping technique by developing a difference potential mapping (DP-method), which can directly measure the potential gradients. Taking this new approach, a permanent connection to the rebar would be no longer required. The work summarizes the development details and the assessment criteria for the DPmethod, which improves the quality of interpretation. The newly defined gradient-width Shows how the detection probability of corrosion-active areas is improved. Moreover, it has been shown that combining the potential measurements with automated large-scale measuring the concrete cover and moisture content lead to a more reliable condition assessment. T3 - BAM Dissertationsreihe - 75 KW - Detektion KW - Zerstörungsfreie Prüfung KW - Stahlbeton KW - Elektrochemische Korrosion KW - Potentialfeld PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-833 SN - 978-3-9814281-5-5 SN - 1613-4249 VL - 75 SP - 1 EP - 183 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-83 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Basan, Ricardo T1 - Untersuchung der intralaminaren Schubeigenschaften von Faserverbundwerkstoffen mit Epoxidharzmatrix unter Berücksichtigung nichtlinearer Effekte N2 - Faserverbundwerkstoffe besitzen anisotrope Materialeigenschaften. Die Anzahl der elastischen Größen und Festigkeiten zur Beschreibung des mechanischen Verhaltens ist dadurch größer als zum Beispiel bei isotropen Werkstoffen. Die Festigkeiten und die Steifigkeiten in den verschiedenen Laminatrichtungen unterscheiden sich darüber hinaus um bis zu zwei Größenordnungen. Abhängig von der Belastungsart versagen Faserverbundwerkstoffe spröde oder duktil. Der Entwicklung geeigneter Untersuchungsmethoden zur Bestimmung der Werkstoffeigenschaften in den verschiedenen Richtungen kommt daher eine grundlegende Rolle zu. Insbesondere die Bestimmung der intralaminaren Schubeigenschaften von Faserverbundwerkstoffen ist aufgrund des ausgeprägten nichtlinearen Last-Verformungs-Verhaltens schwierig und mit den bestehenden Auswerteroutinen genormter Prüfverfahren teilweise fehlerbehaftet. Im Rahmen dieser Arbeit erfolgt die Analyse der Schubeigenschaften in der Laminatebene durch eine neu entwickelte Schubvorrichtung, die eine qualitativ hochwertige Bestimmung der Werkstoffeigenschaften ermöglicht. Für die Probekörper dieser Schubvorrichtung wird auf der Grundlage von Messergebnissen ein lastabhängiges Modell der Schubspannungsverteilung entwickelt, das die Materialnichtlinearität berücksichtigt und bei der Analyse der Versuchsergebnisse zur Anwendung kommt. In vergleichenden Untersuchungen der Interaktion benachbarter Schichten an glas- und kohlenstofffaserverstärkten Laminaten mit ein- und zweiachsiger Orientierung kann gezeigt werden, dass bei identischem Schubspannungszustand in den Einzelschichten bis zu 60% größere Schubfestigkeiten der zweiachsig verstärkten Verbunde vorliegen. Die orthogonal verstärkten Laminate sind schadenstoleranter, da sich Zwischenfaserbruche nicht ungehindert ausbreiten können, sondern an den um 90° gedrehten Fasern gestoppt werden. In Laminaten mit unidirektionaler Faserausrichtung führt dagegen der erste Riss unmittelbar zum Trennbruch. Die Verifizierung dieser Beobachtung erfolgt mittels des Verfahrens der Röntgenrefraktions- topographie. In Schubzugversuchen erfolgt die Korrelation der mechanischen Belastungssituation mit der mikrostrukturellen Analyse der inneren Schädigungsentwicklung des Werkstoffs. An zweiachsig verstärkten Kohlenstofffaserlaminaten unter Zwischenfaserbruchbeanspruchung kann gezeigt werden, dass die Degradation der intralaminaren Schubsteifigkeit mit der Zunahme an inneren Oberflachen als Maß für die Zwischenfaserbruchdichte einhergeht. Einachsig verstärkte Verbunde versagen dagegen relativ spröde bereits durch den ersten Zwischenfaserbruch und damit ohne Zunahme der Mikrorissdichte. Die Zusammenfassung der Erkenntnisse spiegelt sich in der Verbesserung des Auswerteverfahrens des in DIN EN ISO 14129 genormten Schubzugversuchs wider. Unter Berücksichtigung der Nichtlinearitat des Schubmoduls und der Faserrotation infolge der großen Verformungen während des Schubzugversuchs erfolgt in einem Iterationsprozess die stuckweise Anwendung der Klassischen Laminattheorie zur Bestimmung der Einzelschichtspannungen. Die Bewertung der Ergebnisse des Schubzugversuchs mit diesem Analyseverfahren hinsichtlich der Belastungsgrenzen resultiert in einer guten Übereinstimmung mit dem Festigkeitsmodell nach Puck. Die Berücksichtigung nichtlinearer Effekte führt zu einer höheren Genauigkeit bei der Bestimmung der intralaminaren Schubfestigkeit mittels des in der industriellen Anwendung weit verbreiteten Normversuchs. T3 - BAM Dissertationsreihe - 74 KW - Zwischenfaserbruch KW - interfibre failure KW - nonlinearity KW - test methods KW - in-plane shear KW - composite materials KW - Faserverbundwerkstoffe KW - intrlaminare Schubeigenschaften KW - Prüfverfahren KW - Nichtlinearität PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-848 SN - 978-3-9814281-3-1 SN - 1613-4249 VL - 74 SP - 1 EP - 170 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-84 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Lang, Cindy T1 - Sensoren zum Monitoring des Nachernteverhaltens von klimakterischen Früchten N2 - Die Produktqualität, Produktsicherheit und Rückverfolgbarkeit von pflanzlichen Lebensmitteln sind integrierte Aspekte in der nachhaltigen Landwirtschaft. Die in den letzten Jahren zunehmenden Anforderungen an die Lebensmittelprozessketten werden nach internationalen Standards und durch Verordnungen weiter ansteigen. In der vorliegenden Arbeit wurde ein Beitrag zur Entwicklung eines modularen intelligenten Sensorsystems zur durchgängigen Qualitätskontrolle in der Logistikkette von pflanzlichen Frischeprodukten erbracht. Dazu werden innovative Sensoren zum in-situ Monitoring des Nachernteverhaltens von klimakterischen Früchten entwickelt und validiert. Als Referenzmethode zur Detektion des Reifegases Ethylen wurde ein gaschromatographisches System (GC-FID) adaptiert. Die zeitabhängige Ethylenbildung und -emission ist während des Reifeprozesses klimakterischer Früchte anhand von Äpfeln mittels Gaschromatographie- Flammenionisationsdetektion (GC-FID) untersucht und dokumentiert worden. Zur Charakterisierung der Referenzmethode ist aus den Daten der Kalibriergerade die Bestimmungsgrenze berechnet worden. Dabei ergibt sich für die Ethylendetektion mit dem GC-FIDSystem eine Bestimmungsgrenze von xBG = 0,07 ppmV bzw. xBG = 0,08 μg/L. Aus den direkt aus dem Kerngehäuse ermittelten Ethylengehalten lassen sich die idealen Erntezeitpunkte für die Apfelsorten ‘Elstar‘ und ‘Pinova‘ bestimmen. Für die Genussreife des Apfels ‘Elstar‘ ist der optimale Erntezeitraum im Bereich Anfang bis Mitte September festzulegen. Die Apfelsorte ‘Pinova‘ sollte erst ab Anfang Oktober geerntet werden. Die durchgeführten Untersuchungen in dem simulierten Lagerungssystem geben einen Hinweis auf das Nachreifeverhalten der beiden Apfelsorten. Hierbei sind Ethylenemissionsraten bis ERmax = 51,5 μL/kg·h nachgewiesen worden. Im Vergleich dazu werden in der Literatur für die Ethylenemission bei diversen Apfelsorten während des Nachernteprozesses Gehalte von ERLit > 100 μL/kg·h angegeben. Diese gaschromatographische Methode ist für eine online Überwachung und Protokollierung von Transport- und Lagerungsprozessen Vorort weniger geeignet. Die Ethylenemission von klimakterischen Früchten wird in Korrelation zu den Transport- und Lagerungsbedingungen nicht nur mittels Gaschromatographie sondern auch unter Verwendung innovativer Reifeindikatoren als Sensoren analysiert. Zur in-situ Analyse des Nachernteverhaltens von klimakterischen Früchten ist ein opto-chemischer Reifeindikator, basierend auf den chemischen Eigenschaften des Reifegases Ethylen, entwickelt worden. Aufgrund der Reduktionswirkung des Ethylens entstehen Farbänderungen durch den Wechsel der Oxidationsstufen von ausgewählten Metallionen. Die verwendeten Molybdänchromophore verändern sich unter der Einwirkung von Ethylen in einem Farbspektrum von weiß oder hellgelb zu blau. Die Oxidationsstufen des Molybdäns in dem dabei entstandenen Molybdänblau Mo3O8 wurden mittels ESCA untersucht. Die ESCA- Spektren stellen bei der blau gefärbten Molydänverbindung zwei Bindungszustände mit zwei verschiedenen Bindungsenergien (Mo 3d5/2 - Orbital, Intensitätsverhältnis 4:1) dar. Mit der NIST- Datenbank lassen sich die nachgewiesenen Bindungszustände der Molybdänoxide mit den Oxidationsstufen Mo(VI) und Mo(V) interpretieren. Die Reaktionszeit und die Sensitivität des Molybdänfarbwechsels werden in Abhängigkeit der zu detektierenden Ethylenemissionen durch die Modifikation der pH- Werte (pH 1,4 - pH 1,5) einer Ammoniummolybdatlösung variiert. Das außerdem verwendete Reagenz Wasserstoffperoxid dient der Stabilität der Ammoniummolybdatlösung und das eingesetzte Palladiumsulfat wirkt katalytisch auf die Molybdänfarbwechselreaktionen. Die visuelle Auswertung der opto-chemischen Reifeindikatoren mittels eines Farberkennungssensors (L*a*b*-Farbenraum-Modell) erfolgt am Beispiel von Äpfeln unter simulierten Lagerungsbedingungen. Bei steigender Ethylenemission sinken die b*- (in Richtung blau) und die Luminanzkomponente, d. h. der Blauton des Reifeindikators wird in Abhängigkeit der akkumulierten Ethylenmenge intensiver. Die variablen Ethylenindikatoren werden weiterführend zur deskriptiven Lebensmittelsensorik korreliert, um das Reifeverhalten von Äpfeln ganzheitlich charakterisieren zu können. Für die deskriptive Lebensmittelprüfung wurden die äußere Beschaffenheit, der Geruch, der Geschmack und der Reifezustand sensorisch beschrieben und beurteilt. Während des Nachreifeprozesses der Äpfel verändern sich die Farbe der Schale und des Fruchtfleisches sowie der Geruch und der Geschmack. Der sensorische Reifezustand der Äpfel steigt in Abhängigkeit von der Dauer der Lagerung proportional zur gaschromatographisch ermittelten Ethylenemission an. Parallel dazu verändern die an den Äpfeln haftenden opto-chemischen Reifeindikatoren ihre Koloratur mit zunehmender Ethylenemission. Nach einem definierten Lagerungszeitraum ist eine intensive Blaufärbung detektierbar. Des Weiteren wurden spezielle „funkgekoppelte Miniatur-Datalogger“ als mobile Temperaturund Feuchtesensoren zur Erfassung der fruchtnahen klimatischen Bedingungen von Obst und Gemüse in der Nachernteperiode während des Transport- und Lagerungsprozesses untersucht und weiterentwickelt. Diese portablen, kostengünstigen und energiearmen Sensoren ermöglichen eine drahtlose Messdatenübertragung zur Langzeitprotokollierung und -überwachung der Distributionskette von klimakterischen Früchten. Die Validierung der miniaturisierten kapazitiven Polymersensoren ergibt in einem Bereich der relativen Feuchte von 20 bis 85 % Abweichungen von bis zu 4 % vom Referenzwert. Bei zunehmender relativer Feuchte zeigt der Miniatursensor eine geringe Hysterese (1 %). Eine Betauung wird nicht detektiert. Ein Luftstromeinfluss konnte nicht nachgewiesen werden. Das zeitliche Ansprechverhalten liegt bei t90 = 50 s und das Abklingverhalten bei t10 = 212 s. Die klimatischen Bedingungen während des Transports und der Lagerung der klimakterischen Früchte können mit den validierten Temperatur- und Feuchtesensoren in-situ und online überwacht und dokumentiert werden. Um das Nachernteverhalten pflanzlicher Frischeprodukte hinsichtlich der fruchtspezifischen Transpiration detailliert charakterisieren zu können, ist ein Modell einer speziellen Verdunstungsmesskugel mit elektronischem Signal und Datenfernübertragung entwickelt worden. Durch das Modell zur Simulation des Nachernteverhaltens von Tomaten lässt sich dabei eine Korrelation zwischen den relativen Masseverlusten (Wasserdampfabgabe) und der ermittelten relativen Feuchte durch die Sensoren im Inneren der Kugel beschreiben. Mit der Korrelation der relativen Wasserverluste wird ein Monitoring des Transpirationsverhaltens von Tomaten bei Normalbedingungen, bei niedrigen Temperaturen (T = 8 °C) und bei unterschiedlichen Feuchtigkeiten im verpackten Zustand (Kartonage) online möglich. N2 - Requirements for food product quality, safety and traceability have increased in recent years and will increase further, in line with international standards and regulations. To satisfy these requirements without major additional staffing, innovative database driven systems are necessary. Accordingly, this project contributes to develop a modular intelligent sensor system for enabling quality control in the supply chain of fresh plant produce. To this end, sensors for in situ monitoring of the postharvest behaviour of climacteric fruits have been developed and validated. As reference method for the detection of ethylene, a gas chromatographic system has been adapted. The time-dependent ethylene formation and emission has been investigated and documented during the ripening process of climacteric fruits (apples) by means of gas chromatography with flame ionization detection (GC-FID). For the characterisation of the reference method the detection and quantification limits are calculated from the data of the calibration curve. For ethylene detection with the GC-FID system, a quantification limit of xBG = 0.07 ppmV and xBG = 0.08 μg/L is established. Thus, the ideal harvest times for the ‘Elstar’ and ‘Pinova’ apples can be formulated with low ethylene concentrations, directly determined from the apple core. Early to mid September is the best harvest time for ‘Elstar’ to attain optimal maturity and best flavour. The ‘Pinova’ apple should be harvested not before early October. On the other hand the investigations, realised in the simulated storage system, give an indication of the postharvest behaviour of the apples. These ethylene emissions have been detected until ERmax = 51.5 μL/kg·h. For comparison, concentrations of EREth > 100 μL/kg·h for the emission of ethylene with various varieties of apples during the postharvest process are declared in the literature. This gas chromatographic method is less suitable for in situ and online monitoring of transportation and storage processes. The ethylene emission of climacteric fruits is analysed in correlation to the transport and storage conditions using gas chromatography and innovative ripeness indicators as sensors. For in situ analysis of postharvest behaviour of climacteric fruits, an opto-chemical ripeness sensor, based on the chemical properties of the ripening gas ethylene, has been developed. Because of the reduction effect of ethylene, colour changes occur in modification of oxidation state of selected metal ions. The used molybdenum chromophores change under the impact of ethylene in a colour spectrum from white or light yellow to blue. The oxidation states of molybdenum in the incidental molybdenum blue Mo3O8 have been investigated and detected by ESCA. The blue coloured molybdenum compound possesses two bond states with two different bond energies (Mo 3d5/2 – orbital, ratio of intensity 4:1) in the ESCA spectra. According to the NIST database the detected bond states of the molybdenum oxides are interpreted with the oxidation state of Mo (VI) and Mo (V). The reaction time and the sensitivity of molybdenum colour change can be varied by modifying the pH-values (pH 1.4 - pH 1.5) of used ammonium molybdate solution depending on the detected ethylene emissions. The reagent hydrogen peroxide is employed for stability of ammonium molybdate solution and used palladium sulphate influences catalytic the molybdenum colour reactions. Under storage simulated conditions, using the example of apples, the opto-chemical ripeness indicators are recorded visually and are evaluated by a colour recognition sensor (L*a*b* model). With increasing ethylene emission the b*- (in the direction of blue) and luminance factor, the blue colouration of the ripeness indicator is intensely dependent on the amount of accumulated ethylene. The variable ethylene indicators are characterised in correlation to descriptive sensory food evaluation for the holistic characterisation of the ripening behavior of apples. For the descriptive food test, the external appearance, smell, taste and degree of ripeness have been described and evaluated to the senses. During the post-ripening process of apples, the colour of the pericarp and pulp, and the smell and taste also change. Furthermore the sensory degree of ripeness of apples increases depending on the duration of storage and is proportional to the ethylene emission identified by gas chromatography. In parallel, the adherent opto-chemical ripeness indicators on the apples change their colouration with increasing ethylene emission. An intense blue staining is detected over a defined period of storage. In addition special "radio coupled miniature data logger" as mobile temperature and humidity sensors have been studied and developed for detecting the climatic conditions of fruit and vegetables in the postharvest period during transport and storage processes. These portable, low energy and cost-efficient sensors permit wireless data transmission for longterm monitoring of the distribution chain of climacteric fruits. The validation of the miniaturized capacitive polymer sensors results deviations from up to 4 % reference value in a measuring range of relative humidity between 20 and 85 %. A hysteresis, i.e. a difference of humidity indication of the sensor between increasing and decreasing ambient humidity of about 1 % is observed. During increasing humidity the time of response t90 = 50 sec is determined. By contrast, at decreasing humidity the recovery time (212 seconds) is even longer. Impacts of water condensation and environmental gas flow are also studied. The water condensation cannot be detected. The sensor indication does not depend on circulating gas flow, but strongly influenced by temperature deviation. Thus, the climatic conditions during transport and storage of climacteric fruits will be in situ and online monitored by validated temperature and humidity sensors. In order to characterise the postharvest behaviour of crop, with regard to the fruit specific transpiration in detail, a model of a special evapotranspiration ball with electronic signal has been developed. Resulting from this model for simulation of postharvest behaviour of tomatoes a correlation between the relative mass loss (water vapour loss) and the relative humidity determined by the sensors inside the core is described. Accordingly, by means of the correlation of the relative water losses a monitoring of the evapotranspiration of tomatoes at different environmental conditions is online possible. T3 - BAM Dissertationsreihe - 73 KW - Nachernteprozess KW - Transpirationsverhalten KW - Ethylen KW - Reifeverhalten KW - Farbindikator PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-855 SN - 978-3-9814281-1-7 SN - 1613-4249 VL - 73 SP - 1 EP - 136 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-85 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Kromm, Arne T1 - Umwandlungsverhalten und Eigenspannungen beim Schweißen neuartiger LTT-Zusatzwerkstoffe N2 - Die Erkenntnis, dass die Phasenumwandlung bei der Schweißeigenspannungsentstehung hochfester Stähle eine bedeutende Rolle spielt, gibt es bereits seit langer Zeit. Bisher existierten jedoch keine Ansätze, diesen Effekt praktisch zur Schweißeigen- spannungskontrolle zu nutzen. Neuartige Low Transformation Temperature (LTT) Legierungen bieten aufgrund ihrer charakteristischen chemischen Zusammensetzung die Möglichkeit, hochfeste Stähle auf deren Festigkeitsniveau zu fügen. Die martensitische Phasenumwandlung soll zudem eine gezielte Einstellung der Schweißeigenspannungen erlauben. Die im Schrifttum vorliegenden Untersuchungen zu diesem Thema sind zwar zahlreich, bieten jedoch nur wenige Erkenntnisse zur Wechselwirkung zwischen der Phasenumwandlung und den resultierenden Schweißeigenspannungen. Zur Klärung dieser Fragestellung wurde basierend auf Literaturauswertungen eine Matrix von LTT-Legierungen verwirklicht, welche hinsichtlich des Gefüges, der mechanischen Eigenschaften und der Umwandlungstemperaturen charakterisiert wurden. Weiterhin konnten im Rahmen dieser Arbeit erstmals In-situ-Beugungsexperimente während des Schweißens unter Anwendung energiedispersiver Methoden realisiert werden. Die Neukonzeption und Verwirklichung einer Schweißvorrichtung speziell für den Einsatz an Synchrotronstrahllinien ermöglichte die bislang einzigartige In-situ-Analyse der Umwandlungsvorgänge während des Schweißens mit LTT-Legierungen. Im Zuge dieser Experimente konnte neben den im Schweißgut vorherrschenden Umwandlungstemperaturen zusätzlich die Umwandlungskinetik dieser Legierungen ermittelt werden. Die Auswirkungen des Umwandlungsverhaltens wurden anhand der Eigenspannungsverteilungen in der Oberfläche variierender Probengeometrien analysiert. Die Ergebnisse verdeutlichen einerseits, dass die mittels der LTT-Legierungen angestrebte Eigenspannungskontrolle tatsächlich möglich ist. Dies zeigt sich insbesondere dann, wenn eine weitgehend freie Schrumpfung der Naht vorliegt. Mit zunehmender Schrumpfbehinderung ergibt sich jedoch eine Verschiebung des Eigenspannungsniveaus in den Zugbereich. Dies ist bei den hier betrachteten Legierungen vornehmlich in Nahtquerrichtung ausgeprägt. Dagegen ist das Eigenspannungsniveau in Nahtlängsrichtung nahezu unabhängig von den Schrumpfbedingungen. Anhand von Eigenspannungstiefengradienten ließ sich feststellen, dass sich die zusätzliche Schrumpfbehinderung in einer Parallelverschiebung des Eigenspannungsniveaus im Schweißgut äußert. Die Anwendung energiedispersiver Beugungsmethoden erlaubte zudem erstmals die Eigenspannungsermittlung in der parallel zum Martensit vorliegenden austenitischen Phase der LTT-Legierungen. Ergebnisse, die unter Laborbedingungen gewonnen werden, bedürfen zumeist der Überprüfung unter realen Fertigungsbedingungen. Zu diesem Zweck wurde ein Bauteilschweißversuch in einer speziellen Großprüfanalage durchgeführt. Unter konstruktiver Schrumpfbehinderung gelang es, die lastabbauende Wirkung eines spezifischen LTT-Schweißzusatzes anhand einer ausgeprägten Spannungsreduktion während des Schweißens zu belegen. Insgesamt wurde der Nachweis erbracht, dass das Konzept der Low Transformation Temperature (LTT) Legierungen zielführend ist und die nachgewiesene Austenit-Martensitumwandlung einen signifikanten Effekt auf das Eigenspannungsniveau ausübt. N2 - It has long been recognized that phase transformation plays a prominent part in the Evolution of welding residual stresses in high-strength steel. But thus far, no approaches have been available to practically utilize this effect for welding residual stress control. Innovative Low Transformation Temperature (LTT) alloys featuring a characteristic chemical composition open up the possibility for joining high strength steels on their own strength level. Furthermore, martensitic phase transformation is supposed to permit deliberate adjustment of the welding residual stresses. Even though numerous investigations can be found in the literature on this issue, they provide only little insight into the interaction between Phase transformation and resulting welding residual stresses. In order to clarify the problem presented, a matrix of LTT alloys was defined based on evaluated literature. The alloys were characterized with respect to their microstructure, mechanical properties and transformation temperature. Furthermore, it was possible within the scope of this study to realize in-situ experiments during welding using energy-dispersive diffraction methods. The new design and implementation of a welding setup specifically for use at synchrotron beamlines enabled the in-situ diffraction analysis of Transformation processes. In the course of these experiments it could be managed to determine the Transformation temperatures prevailing in the LTT weld metal. In addition the Transformation kinetics of these alloys could be analyzed. The effects of the transformation behavior were analyzed based on the residual stress distributions at the surface of varying specimen geometries. The results illustrate on the one hand that the desired residual stress control by using LTT alloys is actually feasible. This is particularly found in cases with largely free shrinkage of the weld. With increasing shrinkage restraint, however, a shift of the residual stress level into the area of tension is seen to occur. This is observed for the considered alloys to be particularly pronounced in transverse direction of the weld. By contrast, the residual stress level in longitudinal weld direction is nearly independent of the shrinkage conditions. With the help of residual stress depth gradients it could be established that the additional shrinkage restraint manifests itself in a parallel shift of the residual stress level in the weld metal. Application of energy-dispersive diffraction methods additionally allowed it for the first time to determine residual stresses in the austenitic phase of the LTT alloy which is present parallel to martensite. Results gained under laboratory conditions mostly need to be verified under real fabrication conditions. For this purpose, a component weld test was performed in a special large-scale testing facility. Under structural shrinkage restraint, the load relieving effect of a specific LTT welding filler material could be proven by means of a pronounced stress reduction during welding. Overall, evidence was furnished that the concept of Low Transformation Temperature (LTT) alloys is successful and that the proven austenite-martensite transformation exerts a significant effect on the residual stress level. T3 - BAM Dissertationsreihe - 72 KW - residual stresses KW - Synchrotron diffraction KW - phase transformation KW - martensite KW - Eigenspannungen KW - LTT-Zusatzwerkstoff KW - Martensit KW - Phasenumwandlung KW - Synchrotronbeugung KW - LTT filler material PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-861 SN - 978-3-9813853-9-7 SN - 1613-4249 VL - 72 SP - 1 EP - 223 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-86 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Jagst, Eda T1 - Surface Functional Group Characterization Using Chemical Derivatization X-ray Photoelectron Spectroscopy (CD-XPS) N2 - Ziel dieser Arbeit war die Charakterisierung und Quantifizierung von Aminofunktionalitäten auf Oberflächen mittels der Analyseverfahren Röntgen-Photoelektronenspektrometrie (XPS) und Röntgen-Absorptionsspektrometrie (Analyse der Feinstruktur an der Absorptionskante, NEXAFS). Die Oberflächen wurden durch Spincoating, Selbstassemblierung oder Plasmapolymerisation hergestellt und die primären Aminogruppen mit den dafür oft genutzten Markern PFB und TFBA derivatisiert. Die Gasphasenderivatisierungen mittels PFB und TFBA wurden auch genutzt, um Reaktionsverhalten, Reaktionszeit und die resultierenden spektroskopischen Unterschiede genauer zu ermitteln. In nasschemischen Untersuchungen reagierten abgeschirmte Amine mit PFB und TFBA unterschiedlich stark mit Ausbeuten von 78- 89%, was als maximale Ausbeute der Oberflächenderivatisierung in der Gasphase angesehen wird. Die Dünnschichtfilme wurden mittels Spin coating von 4,4’-Methylen-bis(2,6-diethylanilin) auf Si-Wafern hergestellt und reagierten bei 50 ºC mit den Markern. Die Sättigungszeit betrug in beiden Fällen 15 min. Die XPS Messungen zeigten die erfolgreiche Umsetzungen durch das Auftreten eines neuen CF3- bzw. C-F-Signals und einen BE-Verschiebung der entsprechenden C=N-Gruppe. In Übereinstimmung mit den XPS-Daten, zeigen die NEXAFS-Spektren eine Scharfe π*(C=N) Resonanz und die CF3 bzw. C-F Resonanz in der σ*-Region. Die Ausbeuten der Reaktionen wurden aus den Komponenten-Flächen der hochaufgelösten XP N1s Spektren und aus den [F]/[N]-Verhältnissen berechnet. Stöchiometrie und XP-Übersichtsspektren dienten zur Bestimmung der Aminofunktionalitäten an den Oberflächen. Die Resultate waren konsistent und zeigten eine Ausbeute von 80- 90% für PFB und 60-70% für TFBA. Für die Untersuchung von selbstorganisierenden Monoschichten (SAMs) mit unterschiedlichen Funktionalitäten wurden spektroskopische Daten von aliphatischen und aromatischen SAMs mit denen von Si-Wafern, welche mit Polyallylamin und 4,4’-Methylenbis(2,6-diethylanilin) beschichtet wurden, verglichen. Die Orientierung der Monoschichten wurde mittels der winkelaufgelösten NEXAFS an der C K-Kante bestimmt. Die scharfen Signale im Differenzspektrum zeigen eine erfolgreiche Orientierung der Bindungen bzw. funktionellen Gruppen und resultieren aus der Polarisationsabhängigkeit der NEXAFS-Resonanzen an relevanten Molekülorbitalen. Die Gasphasen-Oberflächenderivatisierungen von zwei SAMs mit Aminofunktionalitäten (4-Aminophenylbutan-1- thiolat und 11-Amino-1-undecanthiol) wurden untersucht. Für eine Zeit von 90 min. wurde 4-Aminophenylbutan-1- thiolat mit TFBA bzw. 11-Amino-1-undecanthiol mit PFB bei RT umgesetzt. Die stöchiometrischen Daten der Umsetzungen waren in Übereinstimmung mit den Elementkonzentrationen, welche sich aus den XPS-Daten ableiten ließen. Die Ausbeuten wurden mit Hilfe der N1s-Spektren berechnet und betrugen 60-80%. Da für eine aussagekräftige NEXAFS-Messung eine gewisse Anzahl von Spektren aufgenommen werden muss, steigt die Gefahr der Schädigung der Probe durch Strahlung. Aus diesem Grund wurde ein 11-Amino-1-undecanthiol-Film auf Au für 1 h mit weichem Röntgenlicht bestrahlt und die spektroskopischen Unterschiede an der C und N K- Kante untersucht. Es zeigte sich kein signifikanter Unterschied für die N K-Kante, allerdings erhöhten sich die Intensitäten der C=C und C=N-Spezies im C K-Kanten-Spektrum, was für einen Strahlenschaden spricht. Mittels Allylamin als Plasmagas und Si-Wafern wurden plasma-chemisch abgeschiedene Allylaminfilm Oberflächen hergestellt und untersucht. Der Einfluss der externen Plasmaparameter (Duty Cycle, Plasmaleistung und Druck des gasförmigen Monomers im Reaktor) auf den chemischen Charakter des abgeschiedenen Films wurde im Detail analysiert. Die anschließenden Gasphasen-Oberflächenderivatisierungen mit TFBA und PFB zeigten Nebenreaktionen. C-F- Bindungsbruch und HF-Abspaltung führten zu einem zusätzlichen Signal im XP F1s Spektrum. Oberflächen, welche mit PFB derivatisiert wurden, zeigten einen höheren Anteil von C-F-Bindungsbrüchen, da an fluorierten aromatischen Molekülen leicht nukleophile aromatische Substitutionen stattfinden. Potentielle Schäden durch Röntgenstrahlung wurden mittels TFBA derivatisierter Proben, welche für 10 h der Strahlung ausgesetzt wurden, studiert. Es zeigte sich eine Abnahme der Fluorgehalte an der Oberfläche, allerdings hat dieser Effekt aufgrund der kurzen Messzeiten praktische keine Auswirkung bei der Datenerfassung. Da die HF-Abspaltung auf TFBA- Oberflächen prozentual geringer ist, wurde es als Marker für alle weiteren Kupplungsreaktionen genutzt. Eine Serie von Proben, welche bei einer Plasmaleistung von 20W, 0,5 Duty Cycle und einem Druck von 15 Pa derivatisiert wurden, zeigten eine Sättigungszeit von 90 min. Bei variierenden Plasmabedingungen wurden die unterschiedlichen [CF3]-Flächenprozent in den hochaufgelösten XP C1s Spektren miteinander verglichen. Duty Cycle, Plasmaleistung und Druck zeigten identische Trends in der Retention der Aminogruppen. Grundsätzlich führt die Anwendung von harten Plasmabedingungen, d .h bei hoher effektiver Plasmaleistung, zu Filmen mit einer vergleichsweisen geringen Retention der Aminofunktionalitäten. Darüber hinaus sind diese Filme stark vernetzt bzw. verzweigt. Eine hohe Anzahl ungesättigter Kohlenstoffspezies ist ebenfalls typisch. In Abhängigkeit von den XPS-Daten wurden für die Quantifizierung der Aminogruppen an der Oberfläche die Methoden QEA (Quantitative Elementar-Analyse) und PFA (Peak Fit Analyse) genutzt. Die Berechnungen wurden mittels Youden-Plot verglichen und zeigten keine Abweichung voneinander. NEXAFS wurde zusätzlich genutzt, um den Einfluss der Plasmaparameter auf die Aminogruppen zu studieren, da die Methode empfindlich gegenüber ungesättigten Spezies ist. Eine Zunahme der Fragmentationsraten bei Veränderungen in den Plasmaparametern konnten aus Intensitätsveränderungen in den NEXAFS C K-Kanten Spektren abgeleitet werden. Ein Ringversuch für die Bestimmung von Hydroxylgruppen auf mit Plasma behandelten Oberflächen wurde ebenfalls durchgeführt. Dafür wurde eine Polypropylenfolie, welche Sauerstoffplasma bei 100 W für 90 s ausgesetzt wurde, mit TFAA derivatisiert. Die Oberfläche wurde mittels XPS untersucht und der [OH]-Gehalt mittels QEA und PFA bestimmt. Die Methoden zeigten eine Abweichung von 33% voneinander. CD-XPS wurde erfolgreich zur Bestimmung unterschiedlicher Funktionalitäten auf Dünnschichtfilmen eingesetzt. Allerdings bedarf es für den Erhalt von in sich konsistenten Datensätzen einer validierten Derivatisationsprozedur, die in jedem Labor angewendet werden muss. Die verwendete Hardware und die Peak-Fitting-Prozeduren bei XPSUntersuchungen müssen ebenfalls im Detail beschrieben werden. Die Inhomogenitäten und eventuelle Strahlungsschäden führen zu Abweichungen in den erhaltenen Resultaten. Die gemessene Schichtdicke muss auch für konsistente Ergebnisse optimiert werden. Dünnere Schichten führen zu weniger Hintergrundrauschen. Die erfolgreich durchgeführten Derivatisierungsreaktionen zeigten die Verfügbarkeit der Aminogruppen an der Oberfläche. In einem nächsten Schritt können an diese Funktionalitäten z.B. Stammzellen oder DNA gekoppelt werden, was hochinteressant in Hinblick auf potentielle biologische Anwendungen ist. N2 - Different amino group carrying surfaces, prepared by spin coating, self-assembly and plasma polymerization, were successfully investigated by XPS and NEXAFS. Amino groups were derivatized with the widely used primary amino group tags, PFB and TFBA, prior to analysis. Primary amino group quantification was then carried out according to the spectroscopic data. The gas-phase derivatization reactions of PFB and TFBA were also studied in order to understand their reaction behaviour, the spectral differences they cause and the time required for reaction completion. For the determination of maximum reaction yields of gas-phase surface derivatizations, a set of liquid-phase derivatization reactions was carried out. The selected amino compounds with a different degree of steric hindrance were reacted with PFB and TFBA. The yields (78-89%) were accepted as the upper limit of the gas- phase surface derivatizations. Thin films were prepared by spin coating of 4,4’-methylenebis(2,6-diethylaniline) on Si wafers and were reacted with the markers at 50ºC. The saturation time was found to be 15 min. for both reactions. XPS measurements showed the formation of a CF3 or C-F peak and a BE shift of the corresponding C=N group indicating a successful reaction. The NEXAFS results supported the XPS data by showing a sharp π*(C=N) resonance. The CF3 and C-F resonances were observed in the σ* region. The yields of the reactions were calculated from the component areas of the high resolution XP N1s spectra and from the [F]/[N] ratios. The surface amino groups were calculated from the stoichiometry and from the XP survey scans. The results were consistent with each other and showed a yield of 80-90% for PFB and 60-70% for TFBA. Self-assembled monolayers (SAMs) of different terminal groups were prepared and investigated with XPS and NEXAFS. The spectral properties of aliphatic and aromatic SAMs were compared to the reference surfaces of poly(allylamine) and 4,4’-methylenebis(2,6-diethylaniline) spin coated on Si wafers. NEXAFS was used to determine the orientation of SAMs. An angle resolved NEXAFS was applied at the C K-edge in order to prove a successful SAM deposition on Au. The intense peaks in the difference spectra are due to the polarization dependence in the orbital responsible for the NEXAFS resonance showing a successful bond/functional group orientation. The gas-phase surface derivatization of two amino terminated SAMs, 4-aminophenylbutane-1-thiolate and 11- amino-1-undecanethiol, were studied. 4-aminophenylbutane-1-thiolate was derivatized with TFBA whereas 11- amino-1-undecanethiol with PFB at room temperature for 90 min. The stoichiometrical data were compared to the atomic percentages obtained from the XPS spectra and the results were consistent with each other. The yields of the reactions (60-80%) were obtained from the high resolution N1s spectra. Since a certain number of spectra had to be acquired to reach reasonable S/N ratios, a considerable danger of beam damage in the NEXAFS measurements occurs. The potential radiation damage effects on the C and N K- edge of 11-amino-1-undecanethiol film on Au was studied. The spectral differences before and after 1 h radiation exposure were investigated. The intensities of resonances related to unsaturated species such as C=C and C=N were increased for the C K-edge spectra. The NEXAFS N K-edge spectra of 11-amino-1-undecanethiol film showed no significant irradiation effect. Plasma deposited allylamine samples were successfully investigated by XPS and NEXAFS. Primary amino group quantification on plasma deposited allylamine surfaces was carried out by derivatization after plasma deposition. TFBA and PFB showed side reactions when plasma polymerization was used. Due to the radical mechanisms, C- F bond cleavages followed by HF releases occurred resulting in a second peak formation in XP F1s spectra. PFB derivatized surfaces suffer more from the C-F bond cleavage since fluorinated aromatic molecules are highly susceptible to nucleophilic aromatic substitution. Potential X-ray beam damage of TFBA was studied by a 10 h XPS measurement and showed a fluorine degradation. Due to the short measurement times, X-ray beam damage can be neglected. Since HF release on the TFBA surfaces are lower in percentage, it was used as the marker reagent for the coupling reactions. A series of samples deposited at 20W, 0.5 duty cycle and 15 Pa were derivatized to determine the time required for saturation (90 min.). Plasma polymerized allylamine samples with different duty cycle, power and pressure values were prepared in order to study the effects of external plasma parameters on the primary amino group retention. The [CF3] area percentages, obtained from the high resolution XP C1s spectra, vs. plasma parameter variations were compared. Duty cycle, power and pressure variation experiments showed the same trend on amino group retention. The more the plasma conditions move from mild to hard, the more rearrangements occur on the surface. Milder plasma conditions promote the retention of amino groups originating from the allylamine monomer. QEA (Quantitative Elemental Analysis) and PFA (Peak Fit Analysis) methods were used for the quantification of surface amino groups, depending on the XPS data. The results of two data evaluation methods were compared by using a Youden plot showing no deviation. NEXAFS was used along with XPS in order to study plasma parameter effects on amino groups. As being sensitive against unsaturated moieties, NEXAFS was successfully applied to plasma deposited allylamine surfaces. An increase in fragmentation rate due to a variation in plasma parameters was followed by intensity changes in NEXAFS C K-edge spectra. An inter-laboratory comparison of hydroxyl group determination on plasma surfaces was carried out. Hydroxyl groups on polypropylene foil, treated with oxygen plasma at 100 W for 90 s, were coupled with TFAA. The surfaces were investigated with XPS and the [OH] amount on the surfaces was calculated by QEA and PFA methods showing a 33% deviation between the two methods. CD-XPS is applied successfully in order to determine different functional groups on the thin film surfaces. However, a validated derivatization procedure, which can be easily applied in each lab, should be established. The used hardware and the peak fitting procedures of XPS should be defined in detail for the validation. The sample inhomogeneity and the effects of beam damage play a role on the deviations of the results. The surface thickness should be optimized for consistency. By the derivatization reactions, the surface amino groups are successfully quantified. As the next step, the studied surfaces can be used for potential biological applications, such as coupling the available amino groups with DNA or stem cells. T3 - BAM Dissertationsreihe - 69 KW - functional group KW - photoelectron spectroscopy KW - surface analysis KW - Organic surface KW - plasma modification PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-893 SN - 978-3-9813853-4-1 SN - 1613-4249 VL - 69 SP - 1 EP - 129 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-89 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 41, Heft 4 T3 - Amts- und Mitteilungsblatt der BAM - 4/2011 PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-134 SN - 0340-7551 VL - 41 IS - 4 SP - 1 EP - 125 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-13 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 41, Heft 3 T3 - Amts- und Mitteilungsblatt der BAM - 3/2011 PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-143 SN - 0340-7551 VL - 41 IS - 3 SP - 1 EP - 43 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-14 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 41, Heft 2 T3 - Amts- und Mitteilungsblatt der BAM - 2/2011 PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-159 SN - 0340-7551 VL - 41 IS - 2 SP - 1 EP - 111 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-15 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 41, Heft 1 T3 - Amts- und Mitteilungsblatt der BAM - 1/2011 PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-162 SN - 0340-7551 VL - 41 IS - 1 SP - 1 EP - 187 PB - Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-16 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mente, Tobias T1 - Modellierung des Materialverhaltens eines Duplexstahls auf Mesoebene T2 - MDDK - Master-, Diplomanden-, Doktorandenkolloqium CY - Magdeburg, Germany DA - 2011-05-26 PY - 2011 AN - OPUS4-28130 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ruthard, C. A1 - Maskos, Michael A1 - Yildiz, H. A1 - Gröhn, F. T1 - Association of a cylindrical polyelectrolyte brush with tetravalent counterions N2 - Cylindrical poly(styrene sulfonate) brushes were combined with a tetravalent double-DABCO based counterion. With increasing addition of counterion, hydrodynamic radius and radius of gyration decrease and AFM reveals a conformation change from wormlike to curled structures. Rg/Rh changes from 1.3 to 0.9. Above charge stoichiometry, brushes become interconnected into finite size assemblies, which are stable in aqueous solution for charge ratios (ratio of the molar concentration of charged counterion groups to the molar concentration of charged monomer units of the polymer brush) 1 < Ι < 1.2. They are compact and consist of the brushes in curled (bent) conformation, which is in difference to network-like aggregates from cylindrical poly(styrene sulfonate) brushes with tetravalent porphyrin counterions (Gröhn et al. Macromolecules 2009) and to a wormlike — bent conformation — helix transition found for another brush counterion system (Müller et al. Soft Matter 2009). KW - Bottle-brush KW - Electrostatic interaction KW - Macromonomers KW - Polyelectrolytes KW - Self-assembly PY - 2011 DO - https://doi.org/10.1002/marc.201000622 SN - 1022-1336 SN - 1521-3927 VL - 32 IS - 6 SP - 523 EP - 527 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-25420 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kasper, J. A1 - Hermanns, M. A1 - Bantz, C. A1 - Maskos, Michael A1 - Stauber, R. A1 - Pohl, C. A1 - Unger, R. E. A1 - Kirkpatrick, J.C. T1 - Inflammatory and cytotoxic responses of an alveolar-capillary coculture model to silica nanoparticles: comparison with conventional monocultures N2 - To date silica nanoparticles (SNPs) play an important role in modern technology and nanomedicine. SNPs are present in various materials (tyres, electrical and thermal insulation material, photovoltaic facilities). They are also used in products that are directly exposed to humans such as cosmetics or toothpaste. For that reason it is of great concern to evaluate the possible hazards of these engineered particles for human health. Attention should primarily be focussed on SNP effects on biological barriers. Accidentally released SNP could, for example, encounter the alveolar-capillary barrier by inhalation. In this study we examined the inflammatory and cytotoxic responses of monodisperse amorphous silica nanoparticles (aSNPs) of 30 nm in size on an in vitro coculture model mimicking the alveolar-capillary barrier and compared these to conventional monocultures. Methods Thus, the epithelial cell line, H441, and the endothelial cell line, ISO-HAS-1, were used in monoculture and in coculture on opposite sides of a filter membrane. Cytotoxicity was evaluated by the MTS assay, detection of membrane integrity (LDH release), and TER (Transepithelial Electrical Resistance) measurement. Additionally, parameters of inflammation (sICAM-1, IL-6 and IL-8 release) and apoptosis markers were investigated. Results Regarding toxic effects (viability, membrane integrity, TER) the coculture model was less sensitive to apical aSNP exposure than the conventional monocultures of the appropriate cells. On the other hand, the in vitro coculture model responded with the release of inflammatory markers in a much more sensitive fashion than the conventional monoculture. At concentrations that were 10-100fold less than the toxic concentrations the apically exposed coculture showed a release of IL-6 and IL-8 to the basolateral side. This may mimic the early inflammatory events that take place in the pulmonary alveoli after aSNP inhalation. Furthermore, a number of apoptosis markers belonging to the intrinsic pathway were upregulated in the coculture following aSNP treatment. Analysis of the individual markers indicated that the cells suffered from DNA damage, hypoxia and ER-stress. Conclusion We present evidence that our in vitro coculture model of the alveolar-capillary barrier is clearly advantageous compared to conventional monocultures in evaluating the extent of damage caused by hazardous material encountering the principle biological barrier in the lower respiratory tract. KW - Silica nanoparticles KW - Alveolar-capillary coculture model KW - Cytotoxicity PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-254217 DO - https://doi.org/10.1186/1743-8977-8-6 SN - 1743-8977 VL - 8 IS - 6 SP - 1 EP - 16(?) PB - BioMed Central CY - London AN - OPUS4-25421 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Luty-Blocho, M. A1 - Fitzner, K. A1 - Hessel, V. A1 - Löb, P. A1 - Maskos, Michael A1 - Metzke, D. A1 - Paclawski, K. A1 - Wojnicki, M. T1 - Synthesis of gold nanoparticles in an interdigital micromixer using ascorbic acid and sodium borohydride as reducers N2 - Continuous-flow process conditions for the reduction to gold nanoparticles were varied following a variation scheme aiming at impacting each of the elementary steps–mixing, reaction, polymer diffusion and polymer binding. While the last three variations are done by proper material choice (reducer; polymeric stabilizer), flow processing using a multilamination micromixer intensified the mass transfer in all these steps and particularly improved the first mixing step of the reactants. As reducers L-ascorbic acid (H2Asc) and sodium borohydride (NaBH4) were used and as gold particle precursor chloroauric acid (HAuCl4). All processing runs were analysed by plasmon absorption and transmission electron microscopy to reveal size, shape and polydispersity. For the HAuCl4-H2Asc system, the smallest particles were 0.8–4 nm (7.5 mL/min) and 0.6–3 nm (10.0 mL/min) for the HAuCl4-NaBH4 system. This is at the upper edge of performance reported for batch systems in literature, i.e. among the smallest gold particles generated. While the particles made for the HAuCl4-H2Asc system were polydisperse and polyshaped for most process conditions (however being spherical and relatively uniform at the two largest flow rates investigated), processing with the HAuCl4-NaBH4 system resulted in particles sizes with small mean deviation and almost ideal spherical shape. With polyvinyl alcohol (PVA) as stabilizer, stable colloids were obtained for one week (violet coloured) up to at least 2 months (pink coloured) in case of reaction with ascorbic acid, and for at least 1 month in case of reaction with NaBH4. KW - Au nanoparticles KW - Kinetic of reduction reaction KW - Micromixer KW - Plasmon resonance PY - 2011 DO - https://doi.org/10.1016/j.cej.2011.03.104 SN - 1385-8947 SN - 0300-9467 SN - 0923-0467 SN - 0009-2487 VL - 171 IS - 1 SP - 279 EP - 290 PB - Elsevier CY - Amsterdam ; Boston, Mass. ; Jena ; London ; New York, NY ; Oxford ; Paris ; Philadelphia, PA ; San Diego, Calif. ; St. Louis, Mo. AN - OPUS4-25423 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ruthard, C. A1 - Maskos, Michael A1 - Kolb, U. A1 - Gröhn, F. T1 - Polystyrene sulfonate - porphyrin assemblies: influence of polyelectrolyte and porphyrin structure N2 - In this study, electrostatic self-assembly of different polystyrene sulfonates and a set of tetravalent cationic porphyrins is investigated. It is shown that association of linear polystyrene sulfonates of different molar masses yields finite size nanoscale assemblies that are stable in aqueous solution. Aggregates are compared to the ones of cylindrical brushes, revealing that both form assemblies in the 100 nm range with the charge ratio (molar ratio of porphyrin charges to polyelectrolyte charges) being determining, while the morphology of the resulting network-like assemblies is different for both polyelectrolyte architectures. For the smallest 8k polystyrene sulfonate, in addition, stoichiometric conditions differ. The influence of the molecular porphyrin structure was investigated by comparing meso-tetrakis(4-(trimethyl-ammonium)phenyl)porphyrin (TAPP) with its Cu(II) and Zn(II) loaded analogues and meso-tetrakis(4-N-methylpyridinium)porphyrin (TMPyP), revealing differences in stacking tendency and geometry. Additionally, the TMPyP accumulates more in the inside of the brush than the other porphyrins, likely due to the different position of its charged groups. The supramolecular nanostructures formed were characterized by UV–vis spectroscopy, light scattering, atomic force microscopy, cryo transmission electron microscopy, and small-angle neutron scattering. Results may build a valuable basis for the use of polyelectrolyte–porphyrin assemblies in medicine, catalysis, or energy conversion. KW - Polyelectrolyte KW - Porphyrin KW - Self-assembly KW - Supramolecular nanostructures PY - 2011 DO - https://doi.org/10.1021/jp1078357 SN - 1520-6106 SN - 1520-5207 SN - 1089-5647 VL - 115 IS - 19 SP - 5716 EP - 5729 PB - Soc. CY - Washington, DC AN - OPUS4-25424 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Werner A1 - Tatzky-Gerth, Renate A1 - Wöhlecke, Andreas T1 - Vorläufige Richtlinie für die Zulassung von Bewehrungsgittern aus Kunststoff für Deponieoberflächenabdichtungen PY - 2011 SN - 0340-7551 VL - 41 IS - 4 SP - 411 EP - 444 PB - Wirtschaftsverl. NW CY - Bremerhaven AN - OPUS4-25634 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nemecek, J. A1 - Lehmann, Christian A1 - Fontana, Patrick T1 - Nanoindentation on ultra high performance concrete system N2 - In the past decade, nanoindentation has become commonly used experimental technique for obtaining quantitative data on elastic and inelastic material properties in small volumes, typically in submicron length scale. The methodology was developed mainly for homogeneous materials or, at least, the homogeneity is assumed far enough from the tested volume in evaluation procedures1. Measurement on a heterogeneous system, in which the material phases are intermixed in small volume, is still a challenging task due to several circumstances. First, the preparation of a flat surface on the heterogeneous sample with high differences in stiffness needs Special care. Second, the mechanical interaction between the material phases during surface loading is often unavoidable and therefore the extraction of intrinsic properties of individual phases from the heterogeneous system may not be possible. If differences between the stiffnesses of the interacting phases are low, finding of intrinsic properties can be successful using conventional Evaluation. In other cases, the error in estimating intrinsic properties can reach tens of percent. KW - Mechanical properties KW - nanoindentation KW - Grid indentation KW - Heterogeneous system KW - Ultra high performance concrete PY - 2011 SN - 0009-2770 VL - 105 SP - s656 EP - s659 PB - CSAV CY - Praha AN - OPUS4-25645 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schroeder, H. A1 - Müller, Urs A1 - Ziegert, C. T1 - Buildingcodes and standards in earth building - current situation in Germany T2 - Earth USA 2011 - 6th International earthbuidling conference CY - Albuquerque, NM, USA DA - 2011-09-30 KW - Lehmbau KW - Normen KW - Bauprodukte PY - 2011 SN - 978-0-9824660-2-5 SP - 140 EP - 148 AN - OPUS4-25646 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Beck, Uwe A1 - Stephanowitz, Ralph A1 - Hönig, D. A1 - Domnick, R. T1 - Abschlussbericht zum BMWi/MNPQ-Verbundprojekt VERMERK (versteckte Merkmale) - BMWi-Vorhaben 22/07 PY - 2011 SP - 1 EP - 17 PB - Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25602 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lindner, H. A1 - Murtazin, Ayrat A1 - Groh, S. A1 - Niemax, Kay A1 - Bogaerts, A. T1 - Simulation and experimental studies on plasma temperature, flow velocity, and injector diameter effects for an inductively coupled plasma N2 - An inductively coupled plasma (ICP) is analyzed by means of experiments and numerical simulation. Important plasma properties are analyzed, namely, the effective temperature inside the central channel and the mean flow velocity inside the plasma. Furthermore, the effect of torches with different injector diameters is studied by the model. The temperature inside the central channel is determined from the end-on collected line-to-background ratio in dependence of the injector gas flow rates. Within the limits of 3% deviation, the results of the simulation and the experiments are in good agreement in the range of flow rates relevant for the analysis of relatively large droplets, i.e., ~ 50 µm. The deviation increases for higher gas flow rates but stays below 6% for all flow rates studied. The velocity of the gas inside the coil region was determined by side-on analyte emission measurements with single monodisperse droplet introduction and by the analysis of the injector gas path lines in the simulation. In the downstream region significantly higher velocities were found than in the upstream region in both the simulation and the experiment. The quantitative values show good agreement in the downstream region. In the upstream region, deviations were found in the absolute values which can be attributed to the flow conditions in that region and because the methods used for velocity determination are not fully consistent. Eddy structures are found in the simulated flow lines. These affect strongly the way taken by the path lines of the injector gas and they can explain the very long analytical signals found in the experiments at low flow rates. Simulations were performed for different injector diameters in order to find conditions where good analyte transport and optimum signals can be expected. The results clearly show the existence of a transition flow rate which marks the lower limit for effective analyte transport conditions through the plasma. A rule-of-thumb equation was extracted from the results from which the transition flow rate can be estimated for different injector diameters and different injector gas compositions. PY - 2011 DO - https://doi.org/10.1021/ac201699q SN - 0003-2700 SN - 1520-6882 VL - 83 IS - 24 SP - 9260 EP - 9266 PB - American Chemical Society CY - Washington, DC AN - OPUS4-25605 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gschwind, S. A1 - Flamigni, L. A1 - Koch, J. A1 - Borovinskaya, O. A1 - Groh, S. A1 - Niemax, Kay A1 - Günther, D. T1 - Capabilities of inductively coupled plasma mass spectrometry for the detection of nanoparticles carried by monodisperse microdroplets N2 - Recently, first analyses of single sub-micrometre particles, embedded in liquid droplets, by inductively coupled plasma optical emission spectrometry (ICP-OES) with a size-equivalent detection limit of several hundred nanometres were reported.1,2 To achieve lower detection limits which might allow for the analysis of particles in the nanometre size range a more sensitive technique such as mass spectrometry (MS) is required. Various modifications of particle delivery and data acquisition systems commonly used were carried out to install a setup adequate for ICP-MS detection. These modifications enabled us to supply droplets generated by a commercial microdroplet generator (droplet size: 30–40 µm) with nearly 100% efficiency and high uniformity to the ICP. Analyses were performed using both standard solutions of dissolved metals at concentrations of 1 (Ag), 2 (Au), 5 (Au), or 10 (Cu) mg L-1 and highly diluted suspensions of gold and silver nanoparticles with sizes below 110 nm. In doing so, detection efficiencies of 10-6 counts per atom could be achieved while size-related limits of quantification were found to be 21 nm and 33 nm for gold and silver, respectively. Furthermore, the advantages of utilizing microdroplet generators vs. conventional nebulizers for nanoparticle analyses by ICP-MS are discussed. PY - 2011 DO - https://doi.org/10.1039/c0ja00249f SN - 0267-9477 SN - 1364-5544 VL - 26 IS - 6 SP - 1166 EP - 1174 PB - Royal Society of Chemistry CY - London AN - OPUS4-25606 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulz, Wencke A1 - Nofz, Marianne A1 - Kranzmann, Axel A1 - Schorr, S. T1 - Performance of Protection Coatings during Oxyfuel Combustion Condition T2 - DMG-Sektionstreffen "Angewandte Mineralogie in Technik und Umwelt" (AMITU) und "Physik, Chemie und Kristallographie der Minerale" (PCKM) CY - Bad Münster, Germany DA - 2011-02-23 PY - 2011 AN - OPUS4-25592 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schönhals, Andreas T1 - Glass Transition of Ultrathin Films from Main Chain Polymers T2 - Symposium University Leuven CY - Leuven, Belgium DA - 2011-12-15 PY - 2011 AN - OPUS4-25620 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Raedel, Martina A1 - Bücker, Michael A1 - Torge, Manfred T1 - Adhesives for Stained Glass Windows - Development of a New System for Wide Cracks T2 - CCI Symposium 2011: Adhesives and Consolidants for Conservation CY - Ottawa, Canada DA - 2011-10-17 PY - 2011 AN - OPUS4-25665 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Raedel, Martina A1 - Bücker, Michael A1 - Sabel, Martin T1 - Korrosionsschutz für farbig gefasste Eisen - und Gusseisenobjekte T2 - 45. Treffen der ARGE Korrosion/Restaurierung der GfKORR CY - Bochum, Germany DA - 2011-11-14 PY - 2011 AN - OPUS4-25666 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mathejczyk, J. A1 - Pauli, Jutta A1 - Dullin, C. A1 - Napp, J. A1 - Tietze, L.-F. A1 - Kessler, H. A1 - Resch-Genger, Ute A1 - Alves, F. T1 - Spectroscopically well-characterized RGD optical probe as a prerequisite for lifetime-gated tumor imaging N2 - Labeling of RGD peptides with near-infrared fluorophores yields optical probes for noninvasive imaging of tumors overexpressing ανβ3 integrins. An important prerequisite for optimum detection sensitivity in vivo is strongly absorbing and highly emissive probes with a known fluorescence lifetime. The RGD-Cy5.5 optical probe was derived by coupling Cy5.5 to a cyclic arginine–glycine–aspartic acid–D-phenylalanine–lysine (RGDfK) peptide via an aminohexanoic acid spacer. Spectroscopic properties of the probe were studied in different matrices in comparison to Cy5.5. For in vivo imaging, human glioblastoma cells were subcutaneously implanted into nude mice, and in vivo fluorescence intensity and lifetime were measured. The fluorescence quantum yield and lifetime of Cy5.5 were found to be barely affected on RGD conjugation but dramatically changed in the presence of proteins. By time domain fluorescence imaging, we demonstrated specific binding of RGD-Cy5.5 to glioblastoma xenografts in nude mice. Discrimination of unspecific fluorescence by lifetime-gated analysis further enhanced the detection sensitivity of RGD-Cy5.5-derived signals. We characterized RGD-Cy5.5 as a strongly emissive and stable probe adequate for selective targeting of ανβ3 integrins. The specificity and thus the overall detection sensitivity in vivo were optimized with lifetime gating, based on the previous determination of the probés fluorescence lifetime under application-relevant conditions. KW - Time domain near-infrared fluorescence (NIRF) imaging KW - Fluorescence KW - Lifetime KW - Quantum yield KW - RGD-Cy5.5 KW - Spectroscopic analysis PY - 2011 DO - https://doi.org/10.2310/7290.2011.00018 SN - 1535-3508 SN - 1536-0121 VL - 10 IS - 6 SP - 469 EP - 480 PB - Decker CY - Hamilton, Ont. AN - OPUS4-25711 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Maul, Ronald A1 - Kittler, Katrin A1 - Koch, Matthias A1 - Nehls, Irene T1 - Bakterielle Migranten - Algentoxine als neue Herausforderung in der Umweltanalytik N2 - Bioaktive Sekundärstoffe aus Cyanobakterien stellen eine Quelle für pharmazeutisch interessante Wirkstoffkandidaten wie auch eine Herausforderung für die Umwelt- und Lebensmittelanalytik dar. Die Identifizierung ist allerdings nicht trivial. KW - Cyanotoxine KW - Analytik PY - 2011 SN - 0344-1733 SN - 1610-8256 IS - August SP - 56 EP - 58 PB - Vogel CY - Würzburg AN - OPUS4-25733 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dahmen-Levison, U. A1 - Maul, Ronald T1 - Mykotoxin-Bestimmung - jetzt auch vollautomatisch N2 - Überall, wo sich Schimmel bildet, können hochgiftige Mykotoxine entstehen, besorgniserregende Gifte für Mensch und Tier. Ungefähr ein Viertel der Weltnahrungsproduktion ist mit diesen schädlichen Stoffen infizier!, so die Ernährung- und Landwirtschaftsorganisation FAQ. Lebensmittel wie Getreide, Mais und Nüsse, die in grollen Mengen verarbeitet werden, sind ein idealer Nährboden für die Bildung von Mykotoxinen und können bereits vor der eigentlichen Verarbeitung kontaminiert sein. Eine Kontrolle der Lebensmittellieferungen ist also aus Sicherheitsgründen unerlässlich, denn schon geringe Mengen infizierter Lebensmittel können ganze Bestände vergiften. Aufwendige Laborverfahren, die extern von geschultem Fachpersonal durchgeführt werden und daher mehrere Tage dauern, bedeuten hohe Kosten für die verarbeitende Industrie. Die Aokin AG aus Berlin hat mit der Automatisierung des „aokinmycontrol-Systems den Analyseprozess industrietauglich gemacht. PY - 2011 SN - 0027-2949 VL - 148 IS - 12 SP - 386 EP - 390 PB - Schäfer CY - Detmold AN - OPUS4-25734 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grasse, Fabian A1 - Trappe, Volker A1 - Hickmann, Stefan T1 - Zustandsüberwachung von Rotorblättern - Konzeptstudie mittels Bauteilkomponentenversuch T2 - 29. Vortrags- und Diskussionstagung Werkstoffprüfung 2011 CY - Berlin, Germany DA - 2011-12-01 PY - 2011 AN - OPUS4-25696 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Linke, S. A1 - Kühn, Julius A1 - Moritz, W. A1 - Krause, S. T1 - Catalytic properties of continuous gradient ternary palladium alloys T2 - SEMS Graduate Reserarch Show (Queen Mary University London) CY - London, England DA - 2011-10-19 PY - 2011 AN - OPUS4-25688 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neuschaefer-Rube, U. A1 - Bartscher, M. A1 - Neugebauer, M. A1 - Härtig, F. A1 - Goebbels, Jürgen A1 - Ehrig, Karsten A1 - Staude, Andreas T1 - Measurement of micro gears - comparison of optical, tactile-optical and CT-measurements N2 - Micro gears are applied in an increasing quantity in many applications. Therefore, precise measurements are of growing importance to ensure their quality. This contribution describes the measurement of gears of a micro planetary gear set with a tactile probe, a tactile-optical probe, an optical sensor, and computed tomography (CT). For the tactile measurements, a high precision piezoresistive microprobe was used. A so-called fiber probe was applied for tactile-optical measurements. This probe applies image processing to determine the position of the tactile probing element. For all tactile and tactile-optical measurements, single point probing was used. The optical measurements were carried out with an imaging sensor based on focus variation. Due to limited accessibility, on some gears not all regions could be measured by the optical sensor and the tactile-optical probe. In contrast to this, with CT the whole part could be measured with high point density. We used a micro-CT system and carried out measurements with Synchrotron-CT. All the sensors used deliver measurement data in Cartesian coordinates. It is a challenge to transfer these data into coordinates in which gear parameters are defined. For this, special attention must be paid to the determination of the gear axis and to the orientation of the teeth. The applied procedures are detailed for different micro gears. The comparison between data of different measurements was carried out successfully. The deviations between the CT data and the tactile or tactile-optical data lie in the range of only a few micrometers. KW - Micro gears KW - Coordinate metrology KW - Computed tomography KW - Optical sensors KW - Tactile probes PY - 2011 DO - https://doi.org/10.1117/12.872413 SN - 0277-786X SN - 0038-7355 SN - 0361-0748 N1 - Serientitel: Proceedings series – Series title: Proceedings series IS - 7864 SP - 78640H-1 EP - 78640H-9 PB - VDE-Verl. CY - Berlin ; Offenbach AN - OPUS4-25998 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija A1 - Müller, Christina A1 - Gaal, Mate A1 - Fahlbruch, B. A1 - Schombach, D. T1 - Faktor Mensch in der zerstörungsfreien Prüfung -die arbeitspsychologische Sicht, Einfluss auf die Ergebnisse bei der manuellen Ultraschallprüfung T2 - DGZfP - Seminar des FA Ultraschallprüfung CY - Offenbach am Main, Germany DA - 2011-11-09 PY - 2011 AN - OPUS4-26015 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija A1 - Müller, Christina A1 - Gaal, Mate A1 - Fahlbruch, B. A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - Faktor Mensch in der zerstörungsfreien Prüfung -die arbeitspsychologische Sicht, Einfluss bei der Datenauswertung mechanisierter Prüfungen T2 - DGZfP - Seminar des FA Ultraschallprüfung CY - Offenbach am Main, Germany DA - 2011-11-09 PY - 2011 AN - OPUS4-26016 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija T1 - Konzepte für die Untersuchung des menschlichen Einflusses auf die Zuverlässigkeit der zertörungsfreien Prüfung T2 - TÜV NORD Akademie - Symposium CY - Hamburg, Germany DA - 2011-11-23 PY - 2011 AN - OPUS4-26017 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gumenyuk, Andrey T1 - Hybrid Laser Arc Welding of Structural Steels T2 - Ecole Centrale de Nantes CY - Nantes, France DA - 2011-04-05 PY - 2011 AN - OPUS4-26034 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kipphardt, Heinrich A1 - Traub, Heike A1 - Heinrich, Hans-Joachim A1 - Jakubowski, Norbert T1 - Development of Primary standards for element determination and trace analysis T2 - Institutskolloquium (CENAM) CY - Querétaro, Mexico DA - 2011-09-08 PY - 2011 AN - OPUS4-25953 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kipphardt, Heinrich T1 - Advance in non-metal determination T2 - Institutskolloquium (CENAM) CY - Querétaro, Mexico DA - 2011-09-09 PY - 2011 AN - OPUS4-25955 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Noack, J. A1 - Emmerling, Franziska A1 - Kirmse, H. A1 - Kemnitz, E. T1 - Sols of nanosized magnesium fluoride: formation and stabilisation of nanoparticles N2 - The formation of magnesium fluoride sols and xerogels according to the fluorolytic sol–gel synthesis based on the reaction of Mg(OMe)2 with non-aqueous HF has been thoroughly investigated by X-ray scattering (WAXS/XRD), TEM, SAXS, DLS and 19F MAS NMR spectroscopy. Mechanistic insights were gained by following the reaction progress and formation of intermediate phases of the fluorination of magnesium alkoxides. For F:Mg ratios of 0.3 and 0.4 the formation of two crystalline phases was observed containing the recently obtained compound [Mg6F2(OCH3)10(CH3OH)14] hexanuclear dicubane units. The stoichiometric reaction yields magnesium fluoride nanoparticles with crystallite sizes below 5 nm, which show broad reflections in the X-ray diffraction pattern. Metal fluoride sols prepared by this way undergo tremendous changes over the first several weeks after synthesis. Immediately after the fluorination, particles of about 120 nm—probably agglomerates—are formed, which break apart in the course of about one month of ageing and low-viscous, transparent sols with particles of about 12 nm are obtained. At the same time structural re-organisation processes within the magnesium fluoride particles are observed by an increase of the (110) reflection in WAXS. KW - Surface modification KW - Colloidal particles KW - Gold nanoparticles KW - Gel synthesis KW - Small-angle scattering KW - Oxide KW - Polyelectrolytes KW - Aggregation KW - Dispersion PY - 2011 DO - https://doi.org/10.1039/c1jm11943e SN - 0959-9428 SN - 1364-5501 VL - 21 IS - 38 SP - 15015 EP - 15021 PB - Royal Society of Chemistry CY - Cambridge AN - OPUS4-26183 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böllinghaus, Thomas A1 - Mente, Tobias T1 - Schadensfälle geschweißter Rohrleitungen und Maßnahmen zur Vermeidung N2 - Aus wirtschaftlich-technischer Perspektive ergeben sich in den letzten zehn Jahren hinsichtlich der Werkstoffinnovation und -auswahl für geschweißte Rohrleitungen im Wesentlichen zwei Entwicklungsrichtungen: Im Bereich der niedriglegierten Stähle werden immer höher festere Feinkombaustähle mit Streckgrenzen von inzwischen über 900 MPa verwendet. Wirtschaftliches Ziel ist hierbei eine möglichst hohe Kosteneinsparung durch Reduktion der Wanddicke. Für korrosionsbeanspruchte Komponenten, unter anderem im Petrochemie- und Energieanlagenbau besteht das wirtschaftliche Ziel primär darin, eine höhere Kosteneinsparung durch neue Legierungskonzepte zu erzielen und zwar möglichst so, dass bei mindestens gleicher Festigkeit auf die Verwendung von teuren Elementen, wie beispielsweise Nickel, verzichtet werden kann. Beispiele hierfür sind insbesondere hochlegierte martensitische Cr-V-Stähle, supermartensitische Stähle, Lean-Duplexstähle, superaustenitische Stähle und austenitische Cr-Mn-Stähle. Für einige der neu eingeführten Grundwerkstoffe sind die Zusatzwerkstoffe noch in der Entwicklung. In jedem Fall stellen diese Werkstoffinnovationen besondere Ansprüche hinsichtlich einer Rissvermeidung während der schweißtechnischen Verarbeitung, um von vornherein riss- bzw. fehlerfreie Rohrleitungen herzustellen, die eine hohe Sicherheit gegen ein Versagen während der Inbetriebnahme und im Verlauf der vorgesehenen Lebensdauer aufweisen. Fast alle dieser neu eingeführten Rohrleitungswerkstoffe weisen eine reduzierte Heiß- oder Kaltrissresistenz vor allem während des Schweißens mit modernen Hochleistungsprozessen, bspw. Laserhybridschweißen, auf. Dabei besteht nach wie vor Forschungsbedarf hinsichtlich der jeweiligen Entstehungsmechanismen. Da es in den letzten zehn Jahren immer häufiger zu Produktionsausfällen und Schadensfällen mit teilweise katastrophalen Konsequenzen gekommen ist, werden die Ursachen und die Vermeidung fertigungsbedingter Heiß- und Kaltrisse im Folgenden zusammengefasst. T2 - 14. Sommerkurs Werkstoffe und Fügen CY - Magdeburg, Germany DA - 23.09.2011 PY - 2011 SN - 978-3-940961-56-3 SP - 45 EP - 54 CY - Magdeburg AN - OPUS4-26196 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Döring, Joachim A1 - Bartusch, Jürgen A1 - Gaal, Mate A1 - Erhard, Anton A1 - Bovtun, Viktor Petrovic A1 - Yakymenko, Y. T1 - High Voltage Excitation of Ferroelectret Ultrasonic Transducers: Advantages and Limitations T2 - EMF 2011 European Meeting on Ferroelectricity CY - Bordeaux, France DA - 2011-06-26 PY - 2011 AN - OPUS4-26213 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daschewski, Maxim A1 - Prager, Jens A1 - Kreutzbruck, Marc A1 - Harrer, Andrea A1 - Guderian, Matthias A1 - Meyer-Plath, Asmus T1 - Characterisierung eines neuartigen, thermoakustischen Ultraschallwandlers T2 - 18. Workshop "Physikalische Akustik" CY - Bad Honnef, Germany DA - 2011-10-20 PY - 2011 AN - OPUS4-26219 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kannengießer, Thomas A1 - Evans, A. T1 - Effect of titanium and nitrogen on the transformation characteristics of acicular ferrite in reheated C-Mn steel weld metals T2 - IIW Annual Assembly CY - Denver, CO, USA DA - 2011-07-09 PY - 2011 AN - OPUS4-26166 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Carvalho, José Joao T1 - Immunochemical and chromatographic methods for two anthropogenic markers of contamination in surface waters: caffeine and coprostanol N2 - Caffeine (1,3,7-trimethylxanthine) and coprostanol (5β-cholestan-3β-ol) were detected in samples of Berlin's surface water. Their concentrations correlated with the contamination status of the samples, suggesting their usefulness as markers of human activity. Remarkably, caffeine concentrations were always well above the limit of quantitation of 0.025 µg/L. In order to screen surface water samples in larger series, the development of two novel methods was required: a monoclonal antibody-based immunoassay for caffeine and a dispersive liquid-liquid microextraction (DLLME) method, followed by liquid chromatography tandem mass spectrometry (LC-MS/MS) for coprostanol. The caffeine immunoassay developed shows the best analytical limit of detection (LOD) obtained so far for caffeine (0.001 µg/L), allows high-throughput analysis, and does not require sample pre-treatment. The assay was also successfully employed to measure caffeine in beverages, shampoos, caffeine tab-lets, and human saliva. Antibodies to coprostanol are not commercially available. A new strategy to generate anti-coprostanol antibodies was elaborated using an analogous com-pound as hapten – isolithocholic acid (ILA) – and immunizing a group of mice. A polyclonal anti-ILA serum was produced, which binds coprostanol but the low affinity did not permit setting up an immunoassay to measure environmental concentrations of the analyte (in the range of ng/L). Specific anti-ILA immunoglobulin G were also found in the faeces of the immunized mice. Coprostanol was quantified in the water samples using a newly developed LC-MS/MS method using atmospheric pressure chemical ionisation (APCI). Concentrations above 0.1 µg/L were determined after sample preconcentration using DLLME. This extraction method also proved to be successful for enrichment of coprostanol-related compounds such as cholesterol, cholestanol, cholestanone, ergosterol, and stigmasterol. KW - Immunoassay KW - ELISA KW - Koffein KW - Coprostanol KW - Marker KW - Umweltanalytik KW - LC-MS/MS KW - Hybridoma-Technik PY - 2011 DO - https://doi.org/10.18452/16420 SP - 1 EP - 280 CY - Berlin AN - OPUS4-26389 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bethke, John T1 - Stand der Normung (ISO/DIS 16495)/ Revision der BAM-GGR 004 / Entwicklung eines "Kochbuches" (Leitfaden für die Prüfung von Gefahrgutverpackungen) T2 - Sitzung des BAM AK Prüfstellen CY - Berlin, Germany DA - 2011-09-23 PY - 2011 AN - OPUS4-26322 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bethke, John T1 - BAM-GGR 012 - Nachweis der ausreichenden chemischen Verträglichkeit von Verpackungen zur Beförderung gefährlicher Güter aus Polyethylen und aus koextrudiertem Kunststoff gegenüber flüssigen Stoffen. T2 - Sitzung des BAM AK Prüfstellen, BAM CY - Berlin, Germany DA - 2011-09-23 PY - 2011 AN - OPUS4-26323 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - King, M.J. A1 - Iacobucci, P.A. A1 - Mak, W.A. A1 - Wehrstedt, Klaus-Dieter T1 - Report about the IGUS EOS meeting 2011 in Washington, D.C. N2 - IGUS is the International Group of Experts on the Explosion Risks of Unstable Substances. IGUS was established in 1962 with the objective to harmonize test methods used by different countries to identify and quantify the explosive properties of unstable materials. Over the years, IGUS has continued to offer scientists, who are advisers to their governments, and others, a forum to exchange data and information. The Energetic and Oxidizing Substances (EOS) working group as a sub-group of IGUS is dealing with test methods, Classification and safety aspects relating to organic peroxides, self-reactive substances and other energetic substances, fertilizers, ammonium nitrate and oxidizers. The EOS working group holds an annual meeting alternating between Europe, the United States and Japan. The 2011 meeting took place from the 27th to the 29th of April 2011 at the Madison Hotel in Washington, D. C. The meeting was hosted by the Organic Peroxide Producers Safety Division (OPPSD) of the Society of Plastics Industry, Inc. (SPI). This was the fourth EOS meeting held in the USA since 1994. Of particular importance is the fact that 39 colleagues from authorities, universities, research institutes and industries attended the meeting. The delegates came from USA, Canada, China, France, The Netherlands, Norway, Sweden, Italy, Japan, United Kingdom and Germany. This confirms the breadth and scope of this forum and the value the participants associate with being able to contact other colleagues from around the world enabling the effective exchange of scientific results and discussion on the wide-ranging Problems concerning energetic and oxidizing materials. T2 - IGUS EOS Meeting 2011 CY - Washington D.C., USA DA - 27.04.2011 KW - IGUS KW - EOS KW - Organic peroxides KW - Self-reactive substances KW - Test methods KW - Oxidizers KW - Round robin test PY - 2011 SP - 1 EP - 4 AN - OPUS4-26364 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfennig, Anja A1 - Linke, B. A1 - Schulze, S. A1 - Kranzmann, Axel T1 - Corrosion in pipe steels exposed to supercritical CO2 during carbon capture and storage CCS N2 - The CCS technique involves the compression of emission gasses in deep geological layers. To guarantee the safety of the site, CO2-corrosion of the injection pipe steels has to be given special attention when engineering CCS-sites. To get to know the corrosion behaviour samples of the heat treated steel 1.72252CrMo4, used for casing, and the stainless injection-pipe steel 1.4034 X46Cr13 were kept at T=60 °C and ambient pressure as well as p=100 bar for 700 h - 8000 h in a CC 2-saturated synthetic aquifer environment similar to possible geological on-shore CCS-sites in the northern German Basin. The isothermal corrosion behaviour obtained by mass gain of the steels in the gas phase, the liquid phase and the intermediate phase gives surface corrosion rates around 0.1 to 0.8 mm/year at ambient pressure and much lower about 0.02 to 0.2 mm/year at 100 bar where the CO 2 is in its supercritical state. Severe pit corrosion with pit heights around 4.5 mm are only located on the 42CrMo4 steel. Main phase of the continuous complicated multi-layered carbonate/oxide structure is siderite FeCO 3 in both types of steel. T2 - EUROCORR 2011 - Developing solutions for the global challenge CY - Stockholm, Sweden DA - 04.09.2011 KW - Steel KW - Pipeline KW - Corrosion KW - Carbonate layer KW - CCS KW - CO2-storage PY - 2011 SP - Paper 1044-1 EP - Paper 1044-8 AN - OPUS4-28008 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfennig, Anja A1 - Linke, B. A1 - Schulze, S. A1 - Kranzmann, Axel T1 - Static and dynamic long term corrosion experiments in CCS-conditions N2 - Dealing with first corrosion screening experiments to predict the reliability and safety of Germanys first Carbon Capture and Storage site in the northern Bassin of Germany, northwest of the Capital Berlin, laboratory experiments have been established to simulate the particular conditions at T=60 °C, highly saline aquifer water similar to 'Stuttgart Aquifer', but only at ambient pressure. With mounting 2 independent full 2-grade titanium autoclave systems (running up to 250 bar and 300 °C) pressures up to p=100 bar are possible. In 2010 a specific corrosion chamber of 2-grade titanium working up to 100 °C, flowing aqui fer water with different gas mixtures was designed to fit to a high cycle fatigue testing machine. Long term fatigue experiments simulating fatigue crack growth under corrosive environments will soon start. These experiments may not only help engineering a CCS site, but results can be used to improve the maintenance of geothermal energy production sites, especially moved parts such as pumps and shafts. T2 - EUROCORR 2011 - Developing solutions for the global challenge CY - Stockholm, Sweden DA - 04.09.2011 KW - CO2 KW - Static corrosion KW - High cycle fatigue KW - Steel KW - CCS KW - CO2-storage KW - Corrosion PY - 2011 SP - 1 EP - 7 (Paper 1087) AN - OPUS4-28009 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stähler, S.C. A1 - Sens-Schönfelder, C. A1 - Niederleithinger, Ernst T1 - Monitoring stress changes in a concrete bridge with coda wave interferometry N2 - Coda wave interferometry is a recent analysis method now widely used in seismology. It uses the increased sensitivity of multiply scattered elastic waves with long travel-times for monitoring weak changes in a medium. While its application for structural monitoring has been shown to work under laboratory conditions, the usability on a real structure with known material changes had yet to be proven. This article presents experiments on a concrete bridge during construction. The results show that small velocity perturbations induced by a changing stress state in the structure can be determined even under adverse conditions. Theoretical estimations based on the stress calculations by the structural engineers are in good agreement with the measured velocity variations. KW - Bridges (structures) KW - Concrete KW - Interferometry KW - Structural acoustics PY - 2011 DO - https://doi.org/10.1121/1.3553226 SN - 0001-4966 SN - 1520-8524 VL - 129 IS - 4 SP - 1945 EP - 1952 PB - AIP CY - Melville, NY, USA AN - OPUS4-28588 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witt, Jens A1 - Krebber, Katerina A1 - Demuth, J. A1 - Sasek, L. T1 - Fiber optic heart rate sensor for integration into personal protective equipment N2 - This paper reports on a fiber optic sensor for heart rate measurements. The sensor will be integrated into personal protective equipment within the framework of the FP7 EU project i-Protect. Two different sensor prototypes were developed. One is based on fiber Bragg gratings in silica fiber and the other one is based on macrobending effects in polymer optical fiber. T2 - International workshop BioPhotonics 2011 CY - Parma, Italy DA - 08.06.2011 KW - Smart textile KW - Healthcare monitoring KW - Fiber optical sensor KW - FBG KW - Heart rate sensor KW - Macrobending sensor PY - 2011 SN - 978-1-4244-9837-6 DO - https://doi.org/10.1109/IWBP.2011.5954836 IS - Th6.26 SP - 1 EP - 3 AN - OPUS4-24498 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witt, Jens A1 - Schukar, Marcus A1 - Breithaupt, Mathias A1 - Müller, Bernd R. A1 - Krebber, Katerina T1 - MPOF LPGs as radiation sensors N2 - We investigated to our knowledge for the first time the capabilities of long period gratings (LPG) in single-mode microstructured polymer optical fibre (mPOF) as real-time gamma dosimeter. The fibre is made from polymethyl methacrylate (PMMA) with a polycarbonate jacket. We measured the radiation-induced wavelength shift of the mPOF LPG loss feature wavelength and the radiation-induced attenuation of a mPOF for different wavelength between 600 nm and 800 nm for gamma radiation with an energy distribution between 6 keV and 18 keV. T2 - POF 2011 - 20th International conference on plastic optical fibers CY - Bilbao, Spain DA - 14.09.2011 KW - Microstructured polymer optical fibre (mPOF) KW - Long period grating (LPG) KW - Radiation sensor PY - 2011 SP - 1 EP - 3 AN - OPUS4-24499 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witt, Jens A1 - Schukar, Marcus A1 - Krebber, Katerina A1 - Demuth, J. A1 - Sasek, L. T1 - Heart rate sensor for integration into personal protective equipment N2 - This paper reports on a fibre optic sensor for heart rate measurement which is developed within the framework of the FP7 EU project i-Protect. Goal is integration of the sensor into personal protective equipment Two different sensor prototypes based on polymer optical fibre (POF) were developed. One is based on long period gratings in microstrutured POF and the other one is based on macrobending effects in POF. T2 - POF 2011 - 20th International conference on plastic optical fibers CY - Bilbao, Spain DA - 14.09.2011 KW - Heart rate sensor KW - Long period grating KW - Macrobending sensor KW - Microstructured POF (mPOF) KW - Personal protective equipment (PPE) KW - Physiological sensor PY - 2011 SP - 1 EP - 5 AN - OPUS4-24500 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witt, Jens A1 - Breithaupt, Mathias A1 - Erdmann, Jessica A1 - Krebber, Katerina T1 - Humidity sensing based on microstructured POF long period gratings N2 - We investigated the capabilities of long period gratings (LPG) in single-mode microstructured polymer optical fibre (mPOF) for humidity sensing. For that mPOF LPGs were exposed to different humidity levels at a constant temperature of 30°C in a climate chamber. During the long term tests, which took up several weeks, the humidity was changed in several steps while mPOF LPG wavelength and fibre attenuation were measured. We also measured the water uptake of mPOF in environment with different relative humidity. T2 - POF 2011 - 20th International conference on plastic optical fibers CY - Bilbao, Spain DA - 14.09.2011 KW - Microstructured polymer optical fibre (mPOF) KW - Long period grating (LPG) KW - Humidity sensor PY - 2011 SP - 1 EP - 6 AN - OPUS4-24501 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Friedrich, Jörg Florian T1 - Mechanisms of plasma polymerization - reviewed from a chemical point of view N2 - Several reaction mechanisms have been proposed for the formation of plasma polymers, such as monomer fragmentation followed by poly-recombination into randomly structured and crosslinked films; fragmentation, accompanied by the formation of acetylene or other film-forming intermediates and deposition of polystyrene-like material; plasma-initiation of a radical chain-growth polymerization; and ion-molecule reactions, as well as ionic chain-growth polymerization. The bulk structure of plasma polymers is completely irregular, far from that of conventional polymers. The retention of functional groups during plasma polymerization tends to be greater than that of the entire monomer structure found again as an intact repeat unit in the resulting plasma polymer. An alternative method for depositing ultra-thin, pin-hole free coatings, ones that possess regular structures, is by electrospray ionization (ESI) of pre-fabricated polymers. KW - Fragmentation-recombination KW - Mechanism KW - Plasma polymerization KW - Pulsed plasma KW - Structure of plasma polymers PY - 2011 DO - https://doi.org/10.1002/ppap.201100038 SN - 1612-8850 SN - 1612-8869 VL - 8 IS - 9 SP - 783 EP - 802 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-24502 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Moritz, W. A1 - Werner, R. A1 - Tausche, A. A1 - Cherkaschinin, G. A1 - Molajew, R. A1 - Wirth, Thomas A1 - Unger, Wolfgang A1 - Linke, S. T1 - Alloys for gas sensors investigated using the continuous gradient-high throughput screening macroscope CG-HTSM N2 - Ternary alloys have been studied as the gate metal of chemical sensors based on the field effect in silicon. The investigation of reduced poisoning of hydrogen sensors by H2S is presented in the alloy system PdxNiyCo1-x-y. A new method in high throughput screening of alloys is applied. Not singular sample compositions but a continuous gradient in alloy concentrations was produced on a semiconductor sample. A laser scanning system produces a photo current in the semiconductor to map the sensor signal and provide a quasi continuous alloy characterization. The new system is therefore called Continuous Gradient—High Throughput Screening Macroscope (CG-HTSM). Typically 625 alloys are characterized in 15 minutes. The resolution of our set-up allows distinguishing 100.000 alloy compositions. KW - Alloy KW - Sensor KW - High throughput screening KW - Macroscope PY - 2011 DO - https://doi.org/10.1166/sl.2011.1586 SN - 1546-198X SN - 1546-1971 VL - 9 IS - 2 SP - 662 EP - 664 PB - American Scientific Publishers (ASP) CY - Stevenson Ranch, CA, USA AN - OPUS4-24504 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Abou-Ras, D. A1 - Caballero, R. A1 - Fischer, C.-H. A1 - Kaufmann, C.A. A1 - Lauermann, I. A1 - Mainz, R. A1 - Mönig, H. A1 - Schöpke, A. A1 - Stephan, C. A1 - Streeck, C. A1 - Schorr, S. A1 - Eicke, A. A1 - Döbeli, M. A1 - Gade, B. A1 - Hinrichs, J. A1 - Nunney, T. A1 - Dijkstra, H. A1 - Hoffmann, V. A1 - Klemm, D. A1 - Efimova, V. A1 - Bergmaier, A. A1 - Dollinger, G. A1 - Wirth, Thomas A1 - Unger, Wolfgang A1 - Rockett, A.A. A1 - Perez-Rodriguez, A. A1 - Alvarez-Garcia, J. A1 - Izquierdo-Roca, V. A1 - Schmid, T. A1 - Choi, P.-P. A1 - Müller, M. A1 - Bertram, F. A1 - Christen, J. A1 - Khatri, H. A1 - Collins, R.W. A1 - Marsillac, S. A1 - Kötschau, I. T1 - Comprehensive comparison of various techniques for the analysis of elemental distributions in thin films N2 - The present work shows results on elemental distribution analyses in Cu(In,Ga)Se2 thin films for solar cells performed by use of wavelength-dispersive and energy-dispersive X-ray spectrometry (EDX) in a scanning electron microscope, EDX in a transmission electron microscope, X-ray photoelectron, angle-dependent soft X-ray emission, secondary ion-mass (SIMS), time-of-flight SIMS, sputtered neutral mass, glow-discharge optical emission and glow-discharge mass, Auger electron, and Rutherford backscattering spectrometry, by use of scanning Auger electron microscopy, Raman depth profiling, and Raman mapping, as well as by use of elastic recoil detection analysis, grazing-incidence X-ray and electron backscatter diffraction, and grazing-incidence X-ray fluorescence analysis. The Cu(In,Ga)Se2 thin films used for the present comparison were produced during the same identical deposition run and exhibit thicknesses of about 2 µm. The analysis techniques were compared with respect to their spatial and depth resolutions, measuring speeds, availabilities, and detection limits. KW - Elemental distributions KW - Comparison KW - Depth profiling KW - Chemical mapping KW - Thin films KW - Solar cells KW - Chalcopyrite-type KW - Cu(In,Ga)Se2 PY - 2011 DO - https://doi.org/10.1017/S1431927611000523 SN - 1431-9276 SN - 1435-8115 VL - 17 IS - 5 SP - 728 EP - 751 PB - Cambridge University Press CY - New York, NY AN - OPUS4-24506 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Berger, Wolfgang A1 - Kalbe, Ute A1 - Krüger, Oliver A1 - Hennecke, D. T1 - Aktueller Stand der Entwicklung von Elutionsverfahren für organische Schadstoffe (E DIN 19527 und DIN 19528) T2 - Fachveranstaltung des Altlastenforums BW "Novellierung der BBodSchV und GrundwasserV - Auswirkungen auf die Praxis der Altlastenbearbeitung" CY - Stuttgart, Germany DA - 2011-10-20 PY - 2011 AN - OPUS4-24507 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Böllinghaus, Thomas A1 - Gumenyuk, Andrey A1 - Quiroz Penaranda, Vanessa ED - Lippold, J. ED - Böllinghaus, T. ED - Cross, C.E. ED - et al., T1 - Short Term Metallurgy and Hot Cracking During Laser Beam Welding of Austenitic Stainless Steels N2 - Industrial application of high alloyed austenitic stainless steel laser welding has grown significantly in the recent time due to the continuous improvement of compact and high power density lasers systems. The application of such processes meanwhile ranges from pipeline or railway car body manufacturing to the production of household wares. The largest advantages of the laser application to welding production are much higher welding speeds, reduction or complete exclusion of welding consumables, easy design of the weld joints, decrease of thermal distortions and thus, costs saving. In contrast to arc welding, laser beam welding might particularly be associated with metallurgical defects, like the formation of hot cracks. Such phenomena are related to an order of magnitude higher temperature gradients and cooling rates in the solidification zone, providing rapid solidification kinetics which may cause significant segregation of alloying elements such as Ni and Cr and respective undercooling of the solute at the solidification front. In specific metastable austenitic stainless steels alloys in vicinity of the so called eutectic rim of the Fe-Cr-Ni constitutional diagram, such effects might entail a change of solidification mode from primary ferrite to austenite, providing an increased risk of solidification cracking. Previous studies has shown that the primary solidification mode change during laser beam welding of Cr-Ni austenitic stainless steels such alloys could be effectively influenced by nitrogen absorption as well as by the laser plasma type and also proved the occurrence of metastable primary ferritic solidification. In the present contribution, such results are compared to recent investigations of laser welding newer austenitic Fe-Cr-Mn-Ni steel grades by identification of respective hot cracking critical welding parameter intervals and strain rates in the Controlled Thermal Weldability (CTW) Test. PY - 2011 SN - 978-3-642-16863-5 DO - https://doi.org/10.1007/978-3-642-16864-2_7 IS - Part 2 SP - 103 EP - 129 PB - Springer CY - Berlin, Heidelberg AN - OPUS4-24348 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böllinghaus, Thomas A1 - Mente, Tobias T1 - Trends in investigating hydrogen cracking and diffusion in steel welds N2 - ♦ Elongation of the Service life of existent components ♦ Inovative light weight design ♦ Higher strength of the applied materials ♦ Increasingly aggressive environments T2 - 64th IIW Annual assembly and international conference CY - Chennai, India DA - 17.07.2011 PY - 2011 AN - OPUS4-24349 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühn, Julius A1 - Lippitz, Andreas A1 - Linke, S. A1 - Moritz, W. A1 - Unger, Wolfgang T1 - A HAXPES Study of a Ternary Palladium Alloy Metal-Electrolyte-Insulator-Semiconductor System T2 - HAXPES 2011 - 4th International Workshop on Hard-X-ray Photoelectron Spectroscopy CY - Hamburg, Germany DA - 2011-09-14 PY - 2011 AN - OPUS4-24350 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unger, Wolfgang A1 - Kühn, Julius A1 - Unger, Wolfgang A1 - Linke, S. A1 - Moritz, W. T1 - Catalytic Properties of Pd-Ni-Co Alloy Thin Films used as Active Layer of a Hydrogen Sensor T2 - ECASIS 2011 - 14th Conference on Applications of Surface and Interface Analysis CY - Cardiff, Wales DA - 2011-09-04 PY - 2011 AN - OPUS4-24351 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Martínez-Mánez, Ramon A1 - Sancenón, F. A1 - Biyikal, Mustafa A1 - Hecht, Mandy A1 - Rurack, Knut T1 - Mimicking tricks from nature with sensory organic-inorganic hybrid materials N2 - Design strategies for (bio)chemical systems that are inspired by nature's accomplishments in system design and operation on various levels of complexity are increasingly gaining in importance. Within the broad field of biomimetic chemistry, this article highlights various attempts toward improved and sophisticated sensory materials that rely on the combination of supramolecular (bio)chemical recognition principles and nanoscopic solid structures. Examples range from more established concepts such as hybrid sensing ensembles with improved sensitivity and selectivity or for target analytes for which selectivity is hard to achieve by conventional methods, which were often inspired by protein binding pockets or ion channels in membranes, to very recent approaches relying on target-gated amplified signalling with functionalised mesoporous inorganic supports and the integration of native biological sensory species such as transmembrane proteins in spherically supported bilayer membranes. Besides obvious mimicry of recognition-based processes, selected approaches toward chemical transduction junctions utilizing artificially organized synapses, hybrid ensembles for improved antibody generation and uniquely colour changing systems are discussed. All of these strategies open up exciting new prospects for the development of sensing concepts and sensory devices at the interface of nanotechnology, smart materials and supramolecular (bio)chemistry. KW - Sensorik KW - Supramolekulare Chemie KW - Biomimetik KW - Nanotechnologie KW - Hybridmaterialien PY - 2011 DO - https://doi.org/10.1039/c1jm11210d SN - 0959-9428 SN - 1364-5501 VL - 21 IS - 34 SP - 12588 EP - 12604 PB - Royal Society of Chemistry CY - Cambridge AN - OPUS4-24352 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pauli, Jutta A1 - Brehm, Robert A1 - Grabolle, Markus A1 - Behnke, Thomas A1 - Mathejczyk, J. A1 - Hamann, F. A1 - Alves, F. A1 - Hilger, I. A1 - Resch-Genger, Ute ED - Achilefu, S. ED - Raghavachari, R. T1 - Dye-biomolecule conjugates and NIR-fluorescent particles for targeting of disease-related biomarkers N2 - Indispensable for fluorescence imaging are highly specific and sensitive molecular probes that absorb and emit in the near infrared (NIR) spectral region and respond to or target molecular species or processes. Here, we present approaches to targeted fluorescent probes for in vivo imaging in the intensity and lifetime domain exploiting NIR dyes. Screening schemes for the fast identification of suitable fluorophores are derived and design criteria for highly emissive optical probes. In addition, as a signal amplification strategy that enables also the use of hydrophobic NIR fluorophores as fluorescent reporters, first steps towards versatile strategies for the preparation of NIR-fluorescent polymeric particles are presented that can be utilized also for the design of targeted and analyte-responsive probes. KW - Fluorescence KW - Fluorescence lifetime imaging KW - Near-infrared KW - NIR KW - Cyanine dye KW - Cancer KW - In vivo imaging KW - Aggregation KW - Nanoparticle PY - 2011 DO - https://doi.org/10.1117/12.876828 SN - 1605-7422 N1 - Serientitel: Proceedings of SPIE – Series title: Proceedings of SPIE IS - 7910 SP - 791014-1 EP - 791014-15 AN - OPUS4-24353 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schwenk, Christopher A1 - Tikhomirov, D. A1 - Eßer, G. A1 - Rethmeier, Michael T1 - General standard for welding simulation N2 - Für die Abgrenzung der Anwendbarkeit verschiedener Methoden der numerischen Schweißsimulation sowie für die Vereinheitlichung der Voraussetzungen und der durchzuführenden Schritte bei der Simulation sind normative Regelwerke für den Anwender erforderlich. Da es derzeit noch keine normähnlichen Dokumente auf diesem Gebiet gibt, wurde vom Deutschen Institut für Normung e.V. DIN in Zusammenarbeit mit der Forschungsvereinigung des DVS Deutscher Verband für Schweißen und verwandte Verfahren e.V. ein Arbeitsausschuss gegründet, welcher sich mit der Erarbeitung der entsprechenden Dokumente befasst. Der vorliegende Beitrag konzentriert sich auf die Vorstellung der neuen DIN Spec 32534-1, welche die grundlegenden Simulations-Schritte erläutert und ihre Anwendungsfelder sowie die Schlüsselbegriffe spezifiziert. Des Weiteren wurde eine allgemein gültige Simulationsstruktur erarbeitet, welche als Empfehlung für den Auftraggeber und den Auftragnehmer bei der Formulierung und Abwicklung eines Dienstleistungsauftrages sowie für den Neueinstieg in die Schweißsimulation dienen soll. Schließlich wird ein Ausblick auf die weiteren Themenfelder des Arbeitsausschusses sowie auf die internationalen Aktivitäten auf diesem Gebiet gegeben. N2 - For differentiating the applicability of various numerical welding simulation methods as well as unifying the prerequisites and the steps to be taken in simulation, normative codes are required for the user. Since any standard-like documents are currently still lacking in this field, the DIN German Institute for Standardization in partnership with the Research Association of DVS German Welding Society have set up a standards committee dealing with the preparation of respective documents. This article focuses on the presentation of the new DIN Spec 32534-1 explaining the major simulation steps and specifying the application fields and the key terms of welding simulation. In addition, a generally valid simulation structure has been established which is intended to serve as a recommendation for customers and suppliers in formulating and handling a service order as well as for persons who start doing welding simulation for the first time. It additionally gives an overview of the other subject areas dealt with in the standards committee as well as of the international activities in this field. PY - 2011 UR - 10.3139/120.110257 SN - 0025-5300 VL - 53 IS - 9 SP - 522 EP - 527 PB - Hanser CY - München AN - OPUS4-24355 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ehrig, Karsten A1 - Goebbels, Jürgen A1 - Meinel, Dietmar A1 - Paetsch, O. A1 - Prohaska, S. A1 - Zobel, Valentin T1 - Comparison of crack detection methods for analyzing damage processes in concrete with computed tomography N2 - Analyzing damages at concrete structures due to physical, chemical, and mechanical exposures need the application of innovative non-destructive testing methods that are able to trace spatial changes of microstructures. Here, the utility of three different crack detection methods for the analysis of computed tomograms of various cementitious building materials is evaluated. Due to the lack of reference samples and standardized image quality evaluation procedures, the results are compared with manually segmented reference data sets. A specific question is how automatic crack detection can be used for the quantitative characterization of damage processes, such as crack length and volume. The crack detection methods have been integrated into a scientific visualization system that allows displaying the tomography images as well as presenting the results. T2 - DIR 2011 - International symposium on digital industrial raidology and computed tomography CY - Berlin, Germany DA - 20.06.2011 KW - Crack detection KW - Computed tomography KW - Data visualization PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-243569 SN - 978-3-940283-34-4 IS - DGZfP-BB 128 (Poster 2) SP - 1 EP - 8 PB - Deutsche Gesellscahft für Zerstörungsfreie Prüfung e.V. (DGZfP) AN - OPUS4-24356 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kupsch, Andreas A1 - Hentschel, Manfred P. A1 - Lange, Axel A1 - Grothausmann, R. A1 - Manke, I. T1 - Application of the DIRECTT algorithm to sub-nanometer electron tomography N2 - Tomography data obtained from transmission electron microscopes are especially attractive due to their unrivaled spatial resolution in the nanometer range or even less, but they require enormous efforts in sample preparation and suffer from a diverse accumulation of experimental restrictions, which unavoidably result in fundamental reconstruction artifacts. These restrictions refer to: partial opacity, a limited view (limited angle or missing wedge), very few angles (with respect to the detector size), limited to a region of interest (ROI; due to the sample size), variable angular increments as well as sample degradation due the interactions with the electron beam. An advanced version of the DIRECTT (Direct Iterative Reconstruction of Computed Tomography Trajectories) algorithm proves to cope with most of these severe deviations from ideal CT measuring conditions. However, careful data preprocessing is required in order to exploit the capabilities of the algorithm. Nanometer sized Ruthenium catalyst particles for fuel cell applications are 3D imaged at a few Ångström resolution in order to estimate their partial free surface on carbon black supports, which rule the efficiency of the catalytic activity. Comparisons of DIRECTT reconstructions to the conventional filtered back projection, prove the significant improvements. T2 - DIR 2011 - International symposium on digital industrial raidology and computed tomography CY - Berlin, Germany DA - 20.06.2011 KW - Electron tomography KW - Computed tomography KW - Reconstruction algorithms PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-243577 SN - 978-3-940283-34-4 IS - DGZfP-BB 128 (Tu.3.3) SP - 1 EP - 6 PB - Deutsche Gesellscahft für Zerstörungsfreie Prüfung e.V. (DGZfP) AN - OPUS4-24357 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Schwenk, Christopher A1 - Tikhomirov, D. T1 - Standardisierung der numerischen Schweißsimulation N2 - Für die Abgrenzung der Anwendbarkeit verschiedener Methoden der numerischen Schweißsimulation sowie für die Vereinheitlichung der Voraussetzungen und der durchzuführenden Schritte bei der Simulation sind normative Regelwerke für den Anwender erforderlich. Da es derzeit noch keine normähnlichen Dokumente auf diesem Gebiet gibt, wurde vom DIN der Arbeitsausschuss NA 092-00-29-A "Schweißsimulation" gegründet, welcher sich mit der Erarbeitung der entsprechenden Dokumente befasst. Dieses Gremium wurde gemeinsam mit dem Gemeinschaftsausschuss FA 12 "Anwendungsnahe Schweißsimulation" der Forschungsvereinigung des DVS initiiert. Das Ziel der Normungsarbeit im Bereich der numerischen Schweißsimulation besteht in der Erarbeitung einer DIN SPEC, die die Vorgehensweisen bei der Simulation verschiedener Schweißphänomene und -verfahren langfristig standardisieren soll. In einem durch den genannten Arbeitsausschuss bereits vorbereiteten Entwurf der DIN SPEC 32534-1 wurde die Struktur des Hauptdokuments festgelegt. Im Hauptdokument sind die Anwendungsbereiche und die wesentlichen Begriffe der Schweißsimulation spezifiziert. Des Weiteren wurde die allgemein gültige Simulationsstruktur erarbeitet, welche als Empfehlung für den Auftraggeber und den Auftragnehmer bei der Formulierung und Abwicklung eines Dienstleistungsauftrages sowie für den Neueinstieg in die Schweißsimulation dienen soll. Den Schwerpunkt stellt die Vorstellung der neuen DIN SPEC mit der Erläuterung der wesentlichen Simulationsschritte dar. Im Weiteren wird auf die Klassifizierung der Unterdokumente in Abhängigkeit des Schweißverfahrens und des angestrebten Simulationsergebnisses eingegangen. Schließlich wird ein Ausblick auf die weiteren Themenfelder des Arbeitsausschusses NA 092-00-29-A "Schweißsimulation" sowie auf die internationalen Aktivitäten auf diesem Gebiet gegeben. T2 - DVS Congress 2011 - Große Schweißtechnische Tagung CY - Hamburg, Deutschland DA - 27.09.2011 PY - 2011 SN - 978-3-87155-267-0 VL - 275 SP - 21 EP - 26 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-24558 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ünal, Murat A1 - Kühne, Hans-Carsten T1 - Dalles de verre - damage mechanisms, maintenance techniques and mortars for restoration N2 - The present article gives an insight into the research project BEGLARES. Main topics are the restoration “Dalles de Verre” Windows and the development of repair mortars and techniques. This project is executed in cooperation between Glasmalerei Peters GmbH, the University of York, and the BAM Federal Institute for Materials Research and Testing. It is funded by the Federal Ministry of Economics and Technology. The main mechanism of damage, Standards for protection and repair of concrete structures, and the development of repair mortar and special test specimens are presented. T2 - EWCHP-2011 - European workshop on cultural heritage preservation CY - Berlin, Germany DA - 26.09.2011 KW - Dalles de verre KW - Carbonation KW - Maintenance planning KW - Current state analysis KW - Repair techniques PY - 2011 SN - 978-3-8167-8560-6 SP - 289 EP - 293 AN - OPUS4-24560 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Repair mortars for the restoration and reprofiling of natural stone elements in cultural heritage N2 - For the protection of the world's cultural heritage the restoration of listed buildings and monuments is an important task. In many cases the need to repair and reprofile natural stone elements occurs. Repair mortars for such applications have to match historicocultural interests as well as durability related and constructive interests. Currently a research project dealing with the development and optimisation of such mortars is set up at the BAM. Special focus is laid on the possibility of a modular adaption to match a vast variety of stone properties. Besides the development and lab scale testing of the mortar system, an in-situ application will be planned and executed. T2 - EWCHP-2011 - European workshop on cultural heritage preservation CY - Berlin, Germany DA - 26.09.2011 KW - Repair mortar KW - Natural stone KW - Stone restoration KW - Stone reprofiling KW - Modular system KW - Listed buildings and monuments PY - 2011 SN - 978-3-8167-8560-6 SP - 281 EP - 288 AN - OPUS4-24561 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Oliver A1 - Christoph, Gabriele A1 - Kalbe, Ute A1 - Berger, Wolfgang T1 - Monitoring of PAH in aqueous samples - a comparison of different sample preparation techniques T2 - International conference environmental (bio)technologies CY - Gdansk, Poland DA - 2011-09-05 KW - Stir bar sorptive extraction KW - Liquid-liquid extraction KW - Leaching, batch test KW - Column test KW - Complex aqueous matrix PY - 2011 IS - Paper 21 SP - 1 EP - 16 AN - OPUS4-24562 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Woydt, Mathias T1 - Biolubrifiants N2 - Un point de départ pour la mise en route des lubrifiants « neutre à l'environnement » ont été les huiles perdues et les fuites accidentelles, les lubrifiants perdus rejoignant les sols et les eaux (voir lac de Constance). Même en prenant en compte les voies du recyclage, la combustion dans les moteurs et les fuites connues, environ 30 % (entre 20 % et 40 %, selon les études) du volume de lubrifiants entre dans l'environnement par des voies non attribuables ou est probablement mis en décharge de manière illégale. Avec de tels chiffres publics, les arguments des lobbyistes de l'industrie pétrochimique, affirmant que, dans la plupart des applications, les fluides sont enfermés dans des réservoirs clos et étanches, ne convainquent pas les politiques. C'est aussi peut-être parce que, en Allemagne, environ 60 % des particuliers changent leur huile eux-mêmes. KW - Bioöle KW - Gesetzgebung KW - Ester KW - Polyglykole KW - Mineralöle KW - Toxikologie KW - Abbaubarkeit KW - Nachwachsend PY - 2011 SN - 2114-2300 IS - 9 SP - TRI 1 800-1-11, EP - Doc TRI 1 800-1 CY - Paris, France AN - OPUS4-24563 LA - fra AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan A1 - Rübner, Katrin A1 - Meng, Birgit A1 - Hauer, B. T1 - Assessment concept for the sustainable use of secondary aggregates in concrete N2 - Nowadays there are several applications of mineral recycling materials and residues. At present an assessment method for the use of secondary raw materials, which considers sustainability aspects, does not exist. In the framework of the German DAfStb/BMBF research project 'Sustainable Building with Concrete' an assessment concept was developed. It includes the following four assessment steps: I. Basic considerations, II. Advantages for sustainable construction, III. Alternative paths for application, and IV. Sensitivity analysis. The concept was developed on the basis of recycled concrete aggregates, which are already used according to German standards. Afterwards, it was applied and verified by the evaluation of the utilisation of municipal solid waste incinerator bottom ashes. T2 - International RILEM conference on advances in construction materials through science and engineering CY - Hong Kong, China DA - 05.09.2011 KW - Sustainability KW - Assessment KW - Secondary aggregates KW - Concrete PY - 2011 SN - 978-2-35158-116-2 VL - PRO 79 IS - Chapter 10 / Study of sustainable use... SP - 1 EP - 8 PB - RILEM Publications AN - OPUS4-24564 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmigalla, S. A1 - Heyn, Andreas A1 - Wesling, V. A1 - Reiter, R. A1 - Echtermeyer, P. T1 - Investigation of the pitting corrosion behaviour of nickel based alloy claddings by evaluation of electrochemical noise measurements N2 - Claddings of different nickel based alloys were generated on a mild Steel (S235JR) and a stainless steel type 304 by Cold Metal Transfer (CMT). This welding procedure possesses a low degree of mixing between the Substrate and cladding material. Thus it improves the corrosion behaviour of the claddings. The aim of our investigations was to examine the effect of the welding parameters: energy per unit length, shielding gas and finishing surface treatment on the pitting corrosion behaviour of the claddings. However, under Standard test conditions nickel based alloys are often resistant to pitting corrosion. Moreover these test methods are inaccurate and require a large period of time resulting from the iterative progress to determine the critical pitting temperature (CPT). A potentiostatic test method was modified using a high concentrated CaCI2-solution and a conventional three electrode measuring cell. The pitting corrosion behaviour is calculated from current noise charges. During the test the course of corrosion is detected online by the evaluation of electrochemical noise Signals while a continuous increase of temperature by a defined heating rate is realised. Thus a critical pitting temperature can be estimated by only one attempt. Furthermore the deviation of the measured CPT is very low compared to Standard tests using gravimetrical and microscopic evaluation. That enables to figure out the influence of the welding parameters in an exact way. T2 - EUROCORR 2011 - Developing solutions for the global challenge CY - Stockholm, Sweden DA - 04.09.2011 KW - Nickelbasislegierung KW - Plattieren KW - Schweißverfahren KW - Cold metal transfer KW - Korrosionsprüfung KW - Elektrochemie KW - Elektrochemisches Rauschen PY - 2011 SP - 1 EP - 9 AN - OPUS4-24565 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lange, Axel A1 - Kupsch, Andreas A1 - Müller, Bernd R. A1 - Hentschel, Manfred P. T1 - Numerical correction of X-ray detector backlighting T2 - HZB User Meeting 2011 CY - Berlin, Germany DA - 2011-11-30 PY - 2011 AN - OPUS4-24566 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Abbruchmethoden vor dem Hintergrund der Ersatzbaustoffverordnung N2 - Beim Abbruch von Gebäuden wird eine Vielzahl von unterschiedlichen Techniken eingesetzt. Der mit Abstand größte Teil der Abbrucharbeiten wird dabei mit mechanischen Verfahren ausgeführt. In Abhängigkeit vom rückzubauenden Gebäude können aber auch hydrodynamische Verfahren (z. B. Hochdruckwasserstrahlen), thermische Verfahren (z. B. Schneidbrennen) oder chemische Verfahren (z. B. Sprengen) angewandt werden. T2 - BGRB-Kongress - Ressourcenschonung durch Baustoff-Recycling CY - Königswinter/Bonn, Deutschland DA - 13.09.2011 KW - Bauschutt KW - Ersatzbaustoffverordnung PY - 2011 SP - 23 EP - 26 AN - OPUS4-24508 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gollwitzer, Christian A1 - Bellon, Carsten A1 - Deresch, Andreas A1 - Ewert, Uwe A1 - Jaenisch, Gerd-Rüdiger T1 - On POD estimations with radiographic simulator aRTist N2 - The computer simulation of radiography is applicable for different purposes in NDT such as for the qualification of NDT systems, the optimization of system parameters, feasibility analysis, model-based data interpretation, education and training of NDT/NDE personnel, and others. Within the framework of the European project PICASSO simulators will be adapted to support reliability assessments of NDT tasks. The radiographic simulator aRTist developed by BAM is well suited for this task. It combines analytical modelling of the RT inspection process with the CAD-orientated object description applicable to various industrial sectors such as power generation, aerospace, railways and others. The analytic model includes the description of the radiation source, the interaction of Radiation with the material of the part, and the detection process with special focus to DIR. To support reliability estimations the simulation tool is completed by a tool for probability of detection (POD) estimation. It consists of a user interface for planning automatic simulation runs with varying parameters, specifically defect variations. Further, an automatic image analysis procedure is included to evaluate the defect visibility and calculate the POD therefrom. T2 - International symposium on digital industrial radiology and computed tomography CY - Berlin, Germany DA - 20.06.2011 KW - Radiographie KW - Computersimulation KW - Probability of detection PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-245092 SN - 978-3-940283-34-4 IS - DGZfP-BB 128 (Tu.2.3) SP - 1 EP - 8 PB - Deutsche Gesellschaft für zerstörungsfreie Prüfung e.V. (DGZfP) AN - OPUS4-24509 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unger, Wolfgang A1 - Min, Hyegeun A1 - Wettmarshausen, Sascha A1 - Friedrich, Jörg F. T1 - A ToF-SIMS study of the deuterium - hydrogen exchange induced by ammonia plasma treatment of polyolefins T2 - 18.th International Conference on Secondary Ion Mass Spectreometry CY - Riva del Garda, Italy DA - 2011-09-19 PY - 2011 AN - OPUS4-24510 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unger, Wolfgang A1 - Min, Hyegeun A1 - Wettmarshausen, Sascha A1 - Friedrich, Jörg F. T1 - A ToF-SIMS study of the deuterium - hydrogen exchange induced by ammonia plasma treatment of polyolefins T2 - 14th European Conference on Applications of Surface and Interface Analysis (ECASIA'11) CY - Cardiff, Wales DA - 2011-09-04 PY - 2011 AN - OPUS4-24511 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kusche, Nadine A1 - Schukar, Vivien A1 - Schilder, Constanze A1 - Köppe, Enrico A1 - Habel, Wolfgang ED - Chang, F.-K. T1 - Development and qualification of FBG-based strain patches and rosettes N2 - A fibre Bragg grating (FBG) strain patch specially adapted for long-term and high-strain applications was developed and characterised. Additionally, in the case of unknown main stress axis, two fibre optic strain rosettes were developed. The design concept for the patch and the rosettes is based on a glass fibre reinforced plastic (gfrp) carrier material. The patches were characterised due to their strain gauge factor and fatigue behaviour. As a result, FBG strain patches with linear strain behaviour and excellent fatigue resistance were developed and can be used as part of a monitoring system for aerospace structures or wind turbine power plants. The rosettes were designed to be small in geometrical size and their strain transfer behaviour was characterised. T2 - 8th International workshop on structural health monitoring 2011 CY - Stanford, CA, USA DA - 13.09.2011 KW - Fibre Bragg grating KW - Patch KW - Rosette KW - Strain gauge factor KW - Fatigue behaviour KW - Validation PY - 2011 SN - 978-1-60595-053-2 VL - 2 SP - 1457 EP - 1465 PB - DEStech Publications, Inc. AN - OPUS4-24512 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weber, Gert A1 - Thommes, H. A1 - Gaul, H. A1 - Hahn, O. A1 - Rethmeier, Michael T1 - Mechanical properties of weldbonded joints of advanced high strength steels N2 - In lightweight car body shell mass production, due to requirements on vehicle weight reduction and carbon dioxide emissions, joining of advanced high strength steels (AHSS) with different joining procedures and especially hybrid bonding techniques is becoming more and more important. One of these hybrid bonding techniques is the combination of resistance spot welding and adhesive bonding called weldbonding. One of the important advantages of weldbonded joints in comparison to resistance spot welded joints are the enhanced mechanical properties. To guarantee sufficiently high quality conditions regarding the strength of the weldbonded joints, the influences of the applied adhesive systems and of different base metal combinations are studied. This is carried out for both non-corrosive and corrosive environments and for the choice of different joining parameters settings. In particular, the mechanical behaviour of the weldbonded joints is investigated under quasi-static, impact and fatigue loads. Furthermore, the energy absorption of the weldbonded joints for both non-corrosive and corrosive environments is studied. It is shown that the weldbonded joints possess higher mechanical strengths in all load cases (quasi-static, impact and fatigue). Corrosive attack affects weldbonded joints, and the quasi-static strength is reduced. Resistance spot welded joints are not affected by the corrosive attack, but even after several weeks of corrosive attack, the quasi-static strength of weldbonded joints remains higher than that of resistance spot welded joints. KW - Weldbonded joints KW - Corrosion KW - Mechanical strength KW - Fracture behaviour KW - Fatigue KW - Crash behaviour PY - 2011 DO - https://doi.org/10.1163/016942411X580090 SN - 0169-4243 SN - 1568-5616 VL - 25 IS - 18 SP - 2369 EP - 2389 PB - VNU Science Press CY - Utrecht AN - OPUS4-24513 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schalau, Bernd T1 - Störfallsimulationen im Offshore-Bereich T2 - ProcessNet AA "Auswirkung von Stoff- und Energiefreisetzung" CY - Frankfurt am Main, Germany DA - 2011-10-20 PY - 2011 AN - OPUS4-24514 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schalau, Bernd T1 - Stand der Diskussion zur Weiterentwicklung der VDI-Richtlinie 3783 Blatt 1 T2 - ProcessNet AA "Auswirkung von Stoff- und Energiefreisetzungen" CY - Frankfurt am Main, Germany DA - 2011-10-20 PY - 2011 AN - OPUS4-24515 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Klinger, Christian A1 - Mehdianpour, Milad A1 - Klingbeil, Dietmar A1 - Bettge, Dirk A1 - Häcker, Ralf A1 - Baer, Wolfram T1 - Failure analysis on collapsed towers of overhead electrical lines in the region Münsterland (Germany) 2005 N2 - End of November 2005 strong south-west wind and heavy snowfall were predominant in the region Münsterland, north-western part of Germany. This led to accretion of a considerable quantity of wet snow to overhead electrical lines in form of snow rolls on the conductors. Eighty-two transmission towers failed catastrophically, most of them by buckling, however some by brittle fracture. As a consequence nearly 250,000 people have been cut off from electrical power supply for several days with major media attention. This paper describes the forensic analysis in order to investigate the failure cause. Therefore extensive materials investigations, mechanical testing of original components and specimens thereof, estimations for the real wind and snow loads and their combinations, structural analyses as well as detailed evaluations on the basis of previous investigations, literature and regulations were conducted. It was revealed that some of the examined components were manufactured from Thomas steel which was partially in embrittled condition. The investigated towers fulfilled the design codes valid at the time of erection. However the present line loads of the wet snow rolls on the conductors exceeded by far the ones given in the design codes valid at that time. The load case leading to failure was reconstructed by the derived positions of loads mainly caused by unequal and asymmetric distribution of snow rolls on left and right electrical system. The loads and corresponding stresses acting on the structure before failure were estimated. By comparison with the fracture forces from mechanical testing of original members of the collapsed tower the component that primarily failed was localised. The primary fracture occurred on a diagonal member under tension made of Thomas steel which was weakened by embrittlement. The failure cause was a combination of heavy weather conditions (storm, approx. 0 °C and wet snowfall leading to heavy snow rolls on conductors), asymmetric loading conditions and the usage of Thomas steel which was partially embrittled. Finally, recommendations for avoiding future failures are given. KW - Transmission towers KW - Thomas steel KW - Embrittlement KW - Snow loads KW - Ice loads PY - 2011 DO - https://doi.org/10.1016/j.engfailanal.2011.07.004 SN - 1350-6307 SN - 1873-1961 VL - 18 IS - 7 SP - 1873 EP - 1883 PB - Elsevier Science Publ. CY - Oxford AN - OPUS4-24517 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grasse, Fabian A1 - Trappe, Volker A1 - Hickmann, Stefan T1 - Measuring service strength on a representative test rotor blade T2 - Joint seminar DTU Technical University of Denmark - BAM: Design and maintenance of support structures for offshore wind converters CY - Copenhagen, Denmark DA - 2011-10-25 PY - 2011 AN - OPUS4-24539 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grasse, Fabian A1 - Trappe, Volker T1 - Fatigue testing and damage mechanics of fibre reinforced plastics T2 - Joint seminar DTU Technical University of Denmark - BAM: Design and maintenance of support structures for offshore wind converters CY - Copenhagen, Denmark DA - 2011-10-25 PY - 2011 AN - OPUS4-24540 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Desinfektionsmaßnahmen - Beständigkeit von Werkstoffen N2 - Der hygienisch einwandfreie Betrieb einer Trinkwasserinstallation ist auch für den Fall komplexer Systeme wie in Krankenhäusern oder Alten- und Pflegeheimen möglich. Notwendige Voraussetzung ist die Beachtung der Vorgaben der allgemein anerkannten Regeln der Technik bei Planung, Ausführung und Betrieb. Zusätzliche Geräte oder die Zugabe von Chemikalien sind dann regelmäßig nicht erforderlich. Im Schadensfall ist die korrekte und umfassende Ermittlung der Ursache für die Beeinträchtigung der Schlüssel zur dauerhaften Abhilfe. Nur die Beseitigung von Mängeln und die Wiederherstellung regelgerechter Betriebsbedingungen ermöglichen dauerhaft störungsfreien Betrieb. Die prophylaktische Zugabe von Desinfektionsmitteln ist weder zulässig noch sinnvoll, ebenso wenig ist damit eine dauerhafte Sanierung von auftretenden Mängeln möglich. Zudem ergibt sich ein erhöhtes Risiko für Schäden durch Korrosion in den dauerhaft mit oxidierenden Substanzen beaufschlagten Installationen. T2 - 3. Deutsches Forum 'Innenraumhygiene' CY - Essen, Deutschland DA - 15.02.2011 PY - 2011 SN - 1615-8695 IS - Kap.: Trinkwasser SP - 1 EP - 9 AN - OPUS4-24541 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Tölle, Florian A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael A1 - Backhaus, A. A1 - Olschok, S. A1 - Reisgen, U. T1 - Eigenspannungsreduzierung in Elektronen- und Laserstrahlschweißnähten mittels nachlaufender Wärmefelder durch schnelle Strahldefokussierung und -ablenkung N2 - Schweißeigenspannungen - im Besonderen infolge von Strahlschweißprozessen - annähernd der werkstoffspezifischen Streckgrenze können durch eine mögliche Spannungsrelaxation oder verstärkte Spannungsrisskorrosion lebensdauerreduzierende Konsequenzen mit sich ziehen. Aus diesem Grund wurden viele Verfahren entwickelt, welche diese Eigenspannungen reduzieren können. Jedoch sind diese Verfahren kostenintensiv oder nur für breite Schweißnähte und einfache Bauteilgeometrien anwendbar. Die in dieser Arbeit dargestellte Methode nutzt den Schweißstrahl für den Schweißprozess sowie in defokussierter Form für eine thermische Nachbehandlung des Bauteils. Hierfür läuft der defokussierte Strahl durch hochfrequente Strahlablenkung beidseitig der Schweißnaht mit einer bestimmten zeitlichen Distanz dem Schmelzbad nach und wird zum Aufheizen dieser Materialbereiche genutzt. Mit dieser Prozedur ist es möglich die Spannungen in schmalen Schweißnähten mit großen Spannungsgradienten im Vergleich zu anderen spannungsreduzierenden Verfahren ohne Kontaktflächen oder zusätzlichem Equipment effizient zu reduzieren. Abhängig von der Bauteilgeometrie und der Strahlleistung können unterschiedliche Prozessparameter für dieses Verfahren angewandt werden. Es werden die Mechanismen der Eigenspannungsreduzierung in diesem Prozess und deren Abhängigkeit von den Prozessparametern anhand von Ergebnissen aus FEM-Simulationen diskutiert. Zudem wird in einer Reihe von experimentellen Ergebnissen die Anwendbarkeit von bereits für lineare Schweißnähte ermittelte Verfahrensparameter auf axiale und radiale Rundnähte nachgewiesen. Hierbei zeigen die besten experimentellen Ergebnisse für Elektronenstrahl- sowie für Laserstrahlschweißnähte Spannungsreduktionen größer als 90 %. T2 - DVS Congress 2011 - Große Schweißtechnische Tagung CY - Hamburg, Deutschland DA - 27.09.2011 PY - 2011 SN - 978-3-87155-267-0 VL - 275 SP - 465 EP - 471 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-24545 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thöns, Sebastian T1 - Monitoring Supported Structural Integrity Management T2 - IRIS Summer Academy CY - Zell am See, Austria DA - 2011-09-04 PY - 2011 AN - OPUS4-24546 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thöns, Sebastian A1 - Rücker, Werner T1 - Überwachungssysteme zur Unterstützung des Managements der Bauwerksintegrität von Brücken T2 - Vortrag an der Bundesanstalt für Straßenwesen CY - Bergisch Gladbach, Germany DA - 2011-08-17 PY - 2011 AN - OPUS4-24547 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Regina A1 - Maierhofer, Christiane A1 - Kreutzbruck, Marc A1 - Schlilling, M. T1 - Numerical method of active thermography for the reconstruction of back wall geometry T2 - Vlth Inernational Workshop NDT in Progress CY - Prague, Czech Republic DA - 2011-10-10 PY - 2011 AN - OPUS4-24549 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Daum, Werner A1 - Czichos, Horst ED - Grote, K.-H. ED - Feldhusen, J. T1 - Messtechnik und Sensorik KW - Messtechnik KW - Sensorik PY - 2011 SN - 978-3-642-17305-9 DO - https://doi.org/10.1007/978-3-642-17306-6 IS - Kap. W SP - W1 EP - W39 PB - Springer CY - Berlin, Heidelberg AN - OPUS4-24550 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Steinborn, Gabriele A1 - Tzschichholz, Grit A1 - Günster, Jens A1 - Keller, M.H. A1 - Manara, J. T1 - Porous TiO2-Y2O3 ceramics with specific infrared-optical properties N2 - The infrared-optical properties and particularly the emissivity of sintered ceramics depend on the material's bulk properties and structural properties such as porosity, pore size distribution and pore diameter. The infrared-optical properties can be varied across a wide range by specifically selecting the material's bulk and structural properties. A major concern of the present study is the development of a ceramic coating material with a total emissivity below 0.2 at a temperature of 800 °C. For this purpose, various samples of a TiO2-Y2O3 (TY) ceramic composite were produced with different properties. On variation in the Y2O3 content from 5 to 60 wt%, the porosity of the ceramic composites varies from 3 % to 47 % with the mean pore diameter lying in a range from 0.3 µm to 1.7 µm. The addition of graphitic pore builders increases the porosity up to 60 % and the mean pore diameter to a maximum of 15 µm. By optimizing the total porosity and the pore size of the TY ceramics, a total emissivity as low as 0.17 at 800 °C could be achieved. KW - Oxide ceramic KW - Porosity KW - Mean pore diameter KW - Infrared optical properties KW - Emissivity PY - 2011 DO - https://doi.org/10.4416/JCST2011-00011 SN - 2190-9385 VL - 2 IS - 3 SP - 183 EP - 190 PB - Göller CY - Baden-Baden AN - OPUS4-24551 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kamenz, C. A1 - Staude, Andreas A1 - Dunlop, J.A. T1 - Sperm carriers in silurian sea scorpions N2 - Invasion of the land by arachnids required adaptations of numerous organs, such as gills evolving into lungs, as well as mechanisms facilitating sperm transfer in a terrestrial environment. Many modern arachnids use spermatophores for this purpose, i.e. sperm transmitters detached from the body. Exceptionally preserved Silurian (423 Ma) fossils of Eurypterus tetragonophthalmus Fischer, 1839 (Chelicerata: Eurypterida) preserve so-called ‘horn organs’ which we here demonstrate as being equivalent to the spermatophore-producing parts of the genital tract in certain modern arachnids. This clarifies a long-running debate about sexing eurypterids based on the shape of the median abdominal (or genital) appendage. To our knowledge this is also the oldest direct evidence for spermatophoremediated sperm transfer in the fossil record and suggests that eurypterids had evolved mating techniques using spermatophores as early as the Silurian, a valuable prerequisite for life on land. Spermatophores are absent in sea spiders (Pycnogonida) and horseshoe crabs (Xiphosura); thus the shared presence of sclerotized sperm-transfer devices in eurypterids and arachnids is a novel character, newly elucidated here,which offers explicit support for (Eurypterida + Arachnida). For this clade the name Sclerophorata n. nov. is proposed. Arachnida can be further defined by fusion of the originally paired genital opening. KW - Fossil KW - Silurian KW - Eurypterida KW - Arachnida KW - Spermatophore KW - Evolution PY - 2011 DO - https://doi.org/10.1007/s00114-011-0841-9 SN - 0933-4793 VL - 98 IS - 10 SP - 889 EP - 896 PB - Schäuble CY - Rheinfelden AN - OPUS4-24552 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bartscher, M. A1 - Ehrig, Karsten A1 - Staude, Andreas A1 - Goebbels, Jürgen A1 - Neuschaefer-Rube, U. T1 - Application of an industrial CT reference standard for cast freeform shaped workpieces N2 - Industrial computed tomography (CT) today is an important method to analyze defects and to measure the geometry of technical products. The measurement capability of industrial CT often depends on the knowledge of the measurement errors being present. Only with this knowledge, effective corrections are possible by manufacturers, or adapted measurement procedures become possible for the customers. Thus, there is the strong need to have adequate reference standards both for the assessment of general dependencies and for the measurement of task-specific effects. Especially the latter are difficult to assess. This paper shows the application of a versatile dismountable workpiece-near reference body for the use with CT. The reference standard was made from a miniaturized cast aluminium (one-)cylinder head. It can be dismounted into four segments, each featuring reference geometries which enable a registration of CT measured and other reference datasets (e.g. from tactile CMM). The reference standard embodies complex freeform surfaces which are a challenging measurement task for CT and other sensors. Here the application of the reference standard is the study of the influence of material mixes. This is realized by adding pieces of other materials which disturb the mono-material measurement. Results of the application of the reference standard are presented using data from industrial micro-CT systems and CMM reference data. A special emphasis is given on the workflow of the data processing and the data analysis. T2 - International symposium on digital industrial radiology and computed tomography CY - Berlin, Germany DA - 20.06.2011 KW - Industrial reference standard KW - Computed tomographie KW - Freeform shaped workpieces PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-245532 SN - 978-3-940283-34-4 IS - DGZfP-BB 128 (We.4.3) SP - 1 EP - 12 PB - Deutsche Gesellschaft für zerstörungsfreie Prüfung e.V. (DGZfP) AN - OPUS4-24553 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Staude, Andreas A1 - Goebbels, Jürgen T1 - Determining the spatial resolution in computed tomography - comparison of MTF and line-pair structures N2 - According to the relevant standards, measurements of suitable test pieces are analysed with the two established methods to determine the spatial resolution of CT data (MTF and contrast of line-pairs). The results are compared and differences are discussed. T2 - International symposium on digital industrial radiology and computed tomography CY - Berlin, Germany DA - 20.06.2011 PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-245544 SN - 978-3-940283-34-4 IS - DGZfP-BB 128 (Tu.4.1) SP - 1 EP - 9 PB - Deutsche Gesellschaft für zerstörungsfreie Prüfung e.V. (DGZfP) AN - OPUS4-24554 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz ED - Papadrakakis, M. ED - Fragiadakis, M. ED - Plevris, V. T1 - High-speed railway tracks of a surface, bridge and tunnel line and some effects on the train-induced bridge and ground vibrations T2 - COMPDYN 2011 - 3rd International thematic conference - Computational methods in structural dynamics and earthquake engineering CY - Corfu, Greece DA - 2011-05-25 KW - Track compliance KW - Surface line KW - Bridge track KW - Tunnel track KW - Ground vibration KW - Layered soil KW - Bridge resonance KW - Train speed KW - Axle sequence KW - Track irregularities PY - 2011 SP - 1 EP - 17(?) AN - OPUS4-24555 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz ED - De Roeck, G. ED - Degrande, G. ED - Lombaert, G. ED - Müller, G. T1 - The dynamic force transfer of slab tracks and floating slab tracks and the corresponding ground vibration T2 - EURODYN 2011 - 8th International conference on structural dynamics CY - Leuven, Belgium DA - 2011-07-04 KW - Railway track KW - Slab track KW - Floating slab track KW - Track-soil interaction KW - Force transfer KW - Ground vibration PY - 2011 SN - 978-90-760-1931-4 SP - 820 EP - 827 AN - OPUS4-24556 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz A1 - Maldonado, M. T1 - Interaction véhicule-voie-sol et vibrations dues aux trains - Modélisations et vérifications expérimentales N2 - Cet article présente plusieurs modèles numériques pour l’étude des phénomènes vibratoires lors du passage d’un train. Les modèles permettent d’estimer la propagation des ondes et les réceptances pour le sol et la voie. Le sol multicouche et le couplage voie-sol sont traités par une (double) intégration sur les nombres d’onde. Les raideurs dynamiques de la voie et du véhicule sont combinées et les forces d’excitation roue-rail dues aux irrégularités de la voie et des roues sont calculées. Ces forces d’excitation permettent de simuler les vibrations du sol lors du passage d’un train. Les modèles sont validés par comparaison avec des mesures sur deux sites, en France et en Allemagne. Les vibrations calculées correspondent bien aux vibrations mesurées. ---------------------------------------------------------------------------------------------------- This contribution presents models that are necessary to calculate the vibrations due to the passage of a train. The models allow to calculate the propagation of the waves and the receptances of the soil and the track. The layered soil and the coupling with the track are treated by a (double) integration in wavenumber domain. The dynamic stiffnesses of the track and vehicle are combined and the excitation forces due to the irregularities of the track and the wheel are calculated. Finally, these excitation forces are used to simulate the ground vibration of a passing train. All these models are validated by a number of different measurements at two sites in France and Germany. KW - Ondes du sol multicouche KW - Irrégularités et forces roue-rail KW - Wave propagation KW - Layered soil KW - Wheel-rail irregularities and forces PY - 2011 DO - https://doi.org/10.3166/EJCM.20.257-280 SN - 1779-7179 VL - 20 IS - 5-6 SP - 257 EP - 280 PB - Hermès Science : Lavoisier CY - Paris AN - OPUS4-24557 LA - fra AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Golze, Manfred T1 - Rückführung mittels Referenzmaterialien T2 - muva Jubiläumssymposium Ringversuche/Referenzmaterialien CY - Wald (Allgäu), Germany DA - 2011-09-21 PY - 2011 AN - OPUS4-24528 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Golze, Manfred T1 - Rückführung mittels Referenzmaterialien T2 - GDCh-Fortbildungskurs "Qualitätssicherung im Analytischen Labor" CY - Frankfurt am Main, Germany DA - 2011-09-28 PY - 2011 AN - OPUS4-24529 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Golze, Manfred T1 - Auswertung der Messunsicherheit von Analysenergebnissen T2 - GDCh-Fortbildungskurs "Qualitätssicherung im Analytischen Labor" CY - Frankfurt am Main, Germany DA - 2011-09-28 PY - 2011 AN - OPUS4-24530 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Woydt, Mathias A1 - Merryweather, St. A1 - Zweifel, D. T1 - Fuel economy through engine oils based on polyalkylene glycols T2 - Tribologie-Fachtagung 2011 CY - Göttingen, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-24531 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scholz, Christian A1 - Spaltmann, Dirk A1 - Woydt, Mathias T1 - Höchstbelastbare Wälzkontakte mit geringer Misch-/Grenzreibungszahl T2 - Tribologie-Fachtagung 2011 CY - Göttingen, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-24532 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hartelt, Manfred A1 - Wäsche, Rolf T1 - Verschleißuntersuchungen an Dental-Implantat-Werkstoffen unter partial slip Bedingungen T2 - Tribologie-Fachtagung 2011 CY - Göttingen, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-24533 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Gradt, Thomas ED - Kuo, C.-H. T1 - Tribological behaviour of solid lubricants in hydrogen environment N2 - In a future energy supply system based on renewable sources hydrogen technology will play a key role. Because the amount of energy from renewable sources, such as wind or solar power, differs seasonally and regionally, an energy storage method is necessary. Hydrogen, as an environmentally friendly energy carrier, can fill this gap in an ideal way, in particular for mobile applications (Wurster et al., 2009). Already today, in Germany the amount of hydrogen as a byproduct in chemical industry is enough for fuelling about 1 Mio passenger cars1. Excess electrical power can be used to produce hydrogen by electrolysis. On demand, this hydrogen can be used for mobile or stationary fuel cells. Beside this new developing technology, hydrogen is used as fuel for rocket engines and in chemical industry since a long time. Table 1 comprises some physical parameters of hydrogen. It can be seen that hydrogen gas has a very low density which makes storage at high pressure or in liquid form (LH2) necessary. KW - Tribologie KW - Kryotechnik KW - Wasserstofftechnologie KW - Festschmierstoffe PY - 2011 UR - http://www.intechopen.com/articles/show/title/tribological-behaviour-of-solid-lubricants-in-hydrogen-environment SN - 978-953-307-371-2 DO - https://doi.org/10.5772/22286 IS - Chapter 11 SP - 271 EP - 286 PB - InTech AN - OPUS4-24534 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mix, Renate A1 - Ramanujam, Maalolan A1 - Wachtendorf, Volker A1 - Friedrich, Jörg Florian ED - Reichert, T. T1 - New ways for early detection of polymer ageing N2 - Photo-oxidative ageing of polymers under defined exposure (UV, humidity) was investigated from two points of view: a) the ageing process Starts from the topmost surface and penetrates slowly towards bulk and b) radicals play an important role among ageing. Therefore, X-ray photoelectron (XPS) and electron spin resonance (ESR) spectroscopy were applied to show both, the progressive incorporation of oxygen during in-situ UV irradiation (XPS) and the formation of radicals (ESR) in the polymer. The intensity of ESR Signals served as measure for radical concentration. The Validation of this correlation was checked for polyethylenes (PE) equipped with different concentrations of Hostavin N30 UV stabilizer. T2 - 5th European weathering symposium - Natural and artificial ageing of polymers CY - Lisbon, Portugal DA - 21.09.2011 PY - 2011 SN - 978-3-9813136-2-8 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 15 SP - 157 EP - 163 PB - GUS (Gesellschaft für Umweltsimulation) CY - Pfinztal AN - OPUS4-24535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramanujam, Maalolan A1 - Wachtendorf, Volker A1 - Mix, Renate A1 - Schönhals, Andreas A1 - Friedrich, Jörg Florian ED - Reichert, T. T1 - Influence of UV weathering and humidity on surface & bulk properties of LDPE N2 - The outdoor weathering of polymers is mainly due to UV radiation, water, Pollution, humidity, temperature etc. To understand the effects of weathering, simulated tests need to be undertaken in lab scale. Such tests must be quite efficient and similar to the effects of natural weathering. This paper mainly focuses on the effects of UV radiation along with humidity on LDPE. T2 - 5th European weathering symposium - Natural and artificial ageing of polymers CY - Lisbon, Portugal DA - 21.09.2011 KW - LDPE KW - UV weathering KW - Humidity PY - 2011 SN - 978-3-9813136-2-8 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 15 SP - 211 EP - 218 PB - GUS (Gesellschaft für Umweltsimulation) CY - Pfinztal AN - OPUS4-24536 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Asadi, S. A1 - Schiller, J.H. A1 - Lilienthal, A.J. A1 - Bartholmai, Matthias T1 - An artificial potential field based sampling strategy for a gas-sensitive micro-drone N2 - This paper presents a sampling strategy for mobile gas sensors. Sampling points are selected using a modified artificial potential field (APF) approach, which balances multiple criteria to direct sensor measurements towards locations of high mean concentration, high concentration variance and areas for which the uncertainty about the gas distribution model is still large. By selecting in each step the most often suggested close-by measurement location, the proposed approach introduces a locality constraint that allows planning suitable paths for mobile gas sensors. Initial results in simulation and in real-world experiments with a gas-sensitive micro-drone demonstrate the suitability of the proposed sampling strategy for gas distribution mapping and its use for gas source localization. T2 - IEEE/RSJ International conference on intelligent robots and systems (IROS '11) / Workshop on robotics for environmental monitoring (WREM2011) CY - San Francisco, CA, USA DA - 25.09.2011 KW - Autonomous UAV KW - Chemical sensing KW - Gas distribution modelling KW - Gas source localization KW - Gas sensors KW - Mobile sensing system KW - Quadrocopter KW - Sensor planning KW - Artificial potential field PY - 2011 SP - 34 EP - 38 AN - OPUS4-24537 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lück, S. A1 - Kupsch, Andreas A1 - Lange, Axel A1 - Hentschel, Manfred P. A1 - Schmidt, V. T1 - Statistical comparison of various reconstruction algorithms with respect to missing wedge artifacts T2 - MRS Fall Meeting 2011 CY - Boston, MA, USA DA - 2011-11-28 PY - 2011 AN - OPUS4-24568 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija A1 - Gaal, Mate A1 - Müller, Christina A1 - Fahlbruch, B. A1 - Schombach, D. T1 - Einfluss des Zeitdrucks auf die manuelle Ultraschallprüfung. Untersuchung zu menschlichen Faktoren auf die Ergebnisse zerstörungsfreier Prüfungen T2 - DGZfP-Jahrestagung CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24569 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kanzler, Daniel T1 - Bundesanstalt für Materialforschung und -prüfung 8.33 Arbeitsgruppe: Zuverlässigkeit zerstörungsfreier Diagnosesysteme T2 - 1. Fachtagung im ZEWIS CY - Obernburg, Germany DA - 2011-04-13 PY - 2011 AN - OPUS4-24571 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pelkner, Matthias A1 - Reimund, Verena A1 - Neubauer, Andreas A1 - Kreutzbruck, Marc T1 - Lokal Magnetization Unit for GMR Array Based Magnetic Flux Leakage Inspection T2 - QNDE 2011 CY - Burlington, VT, USA DA - 2011-07-17 PY - 2011 AN - OPUS4-24573 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - de Oliveira, Rui A1 - Schukar, Marcus A1 - Krebber, Katerina A1 - Michaud, V. T1 - Distributed strain measurement in CFRP structures by embedded optical fibres: Influence of the coating T2 - 16th International Conference on Composite Structures CY - Oporto, Portugal DA - 2011-06-30 PY - 2011 AN - OPUS4-24574 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - de Oliveira, Rui T1 - Werkstoffintegrierte faseroptische Sensoren für Leichtbaustrukturen T2 - SENSOR + TEST 2011, VDI/VDE-Expertenforum CY - Nuremberg, Germany DA - 2011-06-08 PY - 2011 AN - OPUS4-24575 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gründer, Klaus-Peter T1 - 3D-Verfahren zur Verformungsmessung an Materialien und Bauteilen T2 - Werkstofftechnisches Kolloquium Mess- und Kalibriertechnik CY - Darmstadt, Germany DA - 2011-09-29 PY - 2011 AN - OPUS4-24576 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Günther, Alexander A1 - Gründer, Klaus-Peter T1 - New Bispectral Measurement Device for Fluorescent Materials T2 - 27th Session der CIE CY - Sun City, South Africa DA - 2011-07-10 PY - 2011 AN - OPUS4-24577 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Schukar, Vivien A1 - Tkachenko, Viktoriya T1 - How do application-related issues influence the reliability of fibre optic strain measurements? T2 - IEEE Sensors Conference CY - Limerick, Ireland DA - 2011-10-28 PY - 2011 AN - OPUS4-24578 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Schukar, Vivien A1 - Kusche, Nadine T1 - Calibration facility for quality certification of surface-attached fiber optic and electrical strain sensors (invited lecture) T2 - IEEE Sensors Conference CY - Limerick, Ireland DA - 2011-10-28 PY - 2011 AN - OPUS4-24580 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kanzler, Daniel T1 - Konzept für die Bestimmung der Zuverlässigkeit von zerstörungsfreien Prüfsystemen bei der Prüfung von elektronenstrahlgeschweißten Kupferbehälter für die Endlagerung von hoch radioaktivem Abfall T2 - 1. Fachtagung im ZEWIS CY - Obernburg, Germany DA - 2011-04-13 PY - 2011 AN - OPUS4-24581 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kanzler, Daniel A1 - Müller, Christina A1 - Pitkänen, J. T1 - KONZEPT FÜR DEN EINSATZ DER BAYES`SCHEN STATISTIK IN DER ZUVERLÄSSIGKEITSBESTIMMUNG VON ZERSTÖRUNGSFREIEN DIAGNOSESYSTEMEN DAS PROBLEM ZU KLEINER EXPERIMENTELLER DATENMENGEN T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24583 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pavlovic, Mato A1 - Müller, Christina T1 - Ganzheitliche Zuverlässigkeit - POD der Prüfung von Bauteilen mit komplexer Geometrie T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24584 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiele, Marc A1 - Baeßler, Matthias A1 - Rogge, Andreas A1 - Pirskawetz, Stephan T1 - Schädigungsevolution in Beton unter Ermüdungsbeanspruchung T2 - 52. DAfStb - Forschungskolloquium 2011 CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-24585 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Hoehse, Marek A1 - Buchholz, Uwe A1 - Lothongkam, Chaiyaporn A1 - Heidmann, G. T1 - Fibre-optic sensors for early damage detection in plastic insulations of high-voltage facilities T2 - ISH 2011, 17th International Symposium on High Voltage Engineering CY - Hanover, Germany DA - 2011-08-22 PY - 2011 AN - OPUS4-24586 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Schukar, Vivien A1 - Daum, Werner T1 - Fiber Optic Strain Sensor Standardization - International and European Activities T2 - SAE AeroTech Toulouse 2011 CY - Toulouse, France DA - 2011-10-17 PY - 2011 AN - OPUS4-24587 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nolde, Moana A1 - Schwarz, Silke T1 - Lagergruppe 1.2 - Sicherheitsabstände T2 - Erfahrungsaustausch BG RCI CY - Bad Reichenhall, Germany DA - 2011-09-15 PY - 2011 AN - OPUS4-24518 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schwenk, Christopher A1 - Tikhomirov, D. A1 - Eßer, G. A1 - Rethmeier, Michael T1 - Standardisierung der numerischen Schweißsimulation T2 - Große Schweißtechnische Tagung 2011, DVS Congress und DVS Expo CY - Hamburg, Germany DA - 2011-09-27 PY - 2011 AN - OPUS4-24519 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hoffmann, Katrin A1 - Hoffmann, Angelika A1 - Spieles, Monika A1 - Resch-Genger, Ute T1 - Reference Standard for the performance validation of fluroescence measuring systems T2 - Life Science Day 2011 CY - Berlin, Germany DA - 2011-08-26 PY - 2011 AN - OPUS4-24520 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hoffmann, Katrin A1 - Resch-Genger, Ute A1 - Tannert, S. A1 - Kapusta, P. A1 - Glatz, A. A1 - Goschew, A. A1 - Ortmann, U. A1 - Erdmann, R. T1 - On the Spectral Sensitivity Calibration of Fluorescence Spectrometers: Extensions to the NIR, Polarization and Grating Effects T2 - 12th Conference on Methods and Applications of Fluorescence: Spectroscopy, Imaging and Probes (MAF-12) CY - Strasbourg, France DA - 2011-09-11 PY - 2011 AN - OPUS4-24521 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hoffmann, Katrin A1 - Engel, A. A1 - Bäumle, M. A1 - Resch-Genger, Ute T1 - Characterization of highly fluorescence candidate glass references standards T2 - 12th Conference on Methods and Applicaions of Fluorescence: Spectroscopy, Imaging and Probes (MAF-12) CY - Strasbourg, France DA - 2011-09-11 PY - 2011 AN - OPUS4-24522 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute A1 - Behnke, Thomas A1 - Napp, J. A1 - Fischer, L. A1 - Alves, F. A1 - Schäferling, M. T1 - Targeted Luminescent NIR Nanoprobes for In Vivo Imaging of Tumor Hypoxia T2 - 12th Conference on Methods and Applications of Fluorescence: Spectroscopy; Imaging and Probes (MAF-12) CY - Strasbourg, France DA - 2011-09-11 PY - 2011 AN - OPUS4-24523 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute A1 - Behnke, Thomas A1 - Hübner, Martin A1 - Würth, Christian A1 - Pauli, Jutta A1 - Hoffmann, Katrin A1 - Hoffmann, Angelika T1 - New fluorescence standards for the NIR T2 - 12th Conference on Methods and Applications of Fluorescence: Spectroscopy; Imaging and Probes (MAF-12) CY - Strasbourg, France DA - 2011-09-11 PY - 2011 AN - OPUS4-24524 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maul, Ronald A1 - Rieß, Stephanie A1 - Müller, Chr. A1 - Koch, Matthias A1 - Methner, F.-J. A1 - Nehls, Irene T1 - Intense formation of "masked mycotoxins" during food processing T2 - 5th International Symposium on Recent Advances in Food Analysis (RAFA 2011) CY - Prague, Czech Republic DA - 2011-11-01 PY - 2011 AN - OPUS4-24527 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Döring, Joachim A1 - Bartusch, Jürgen A1 - Brekow, Gerhard A1 - Kreutzbruck, Marc A1 - Beck, Uwe A1 - Weise, Matthias A1 - Bovtun, V. T1 - Parameter reproducibility of polypropylene ferroelectret transducers for air-coupled ultrasonic testing T2 - IEEE International Ultrasonics Symposium 2011 CY - Orlando, FL, USA DA - 2011-10-18 PY - 2011 AN - OPUS4-25201 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Löwe, Peter A1 - Hamann, Andreas T1 - Hochgeschwindigkeits-Stauchvorrichtung mit Stauchkraftmessung und -begrenzung T2 - Werkstoffprüfung 2011 CY - Berlin, Germany DA - 2011-12-01 PY - 2011 AN - OPUS4-25204 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wirth, Cynthia A1 - Günster, Jens A1 - Heinrich, J.G. T1 - Layerwise slurry deposition (LSD) of classic ceramics - an alternative to improve designing in the traditional ceramic industry? T2 - 5th International Conference on Advanced Research in Virtual and Rapid Prototyping (VRAP) CY - Leiria, Portugal DA - 2011-09-28 PY - 2011 N1 - Geburtsname von Wirth, Cynthia: Gomes, C. M. - Birth name of Wirth, Cynthia: Gomes, C. M. AN - OPUS4-25205 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wirth, Cynthia A1 - Günster, Jens A1 - Heinrich, J.G. T1 - Microstructure evolution of a glass ceramic system producend by Layerwise Slurry Deposition (LSD) T2 - EUROMAT 2011 - European Congress and Exhibition on Advanced Materials and Processes CY - Montpellier, France DA - 2011-09-12 PY - 2011 N1 - Geburtsname von Wirth, Cynthia: Gomes, C. M. - Birth name of Wirth, Cynthia: Gomes, C. M. AN - OPUS4-25206 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Boehm, Rainer A1 - Brackrock, Daniel A1 - Kitze, Jessica A1 - Brekow, Gerhard A1 - Kreutzbruck, Marc A1 - Heinrich, W. T1 - Ultraschalluntersuchungen an einem Turbinenradscheibentestkörper mit Sägezahn-Arrays N2 - - Besondere Anforderungen der Prüfaufgabe - Elektronischer Scan für Tandemtechnik bzw. Pitch - Catch Technik - Der ebene Winkelprüfkopf, ein besonderer Gruppenstrahler (PA) - Charakterisierung des Prüfkopfes, Verifikation durch Messung - Messungen am Turbinenradscheibentestkörper T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Ultraschallprüftechnik KW - Phased array KW - Prüfkopfentwicklung KW - Turbinenradscheiben PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-252085 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Di.1.A.3) SP - 1 EP - 21 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25208 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mantouvalou, I. A1 - Wolff, Timo A1 - Hahn, Oliver A1 - Rabin, Ira A1 - Lühl, Lars A1 - Pagels, M. A1 - Malzer, W. A1 - Kanngiesser, B. T1 - 3D Micro-XRF for cultural heritage objects: new analysis strategies for the investigation of the Dead Sea scrolls N2 - A combination of 3D micro X-ray fluorescence spectroscopy (3D micro-XRF) and micro-XRF was utilized for the investigation of a small collection of highly heterogeneous, partly degraded Dead Sea Scroll parchment samples from known excavation sites. The quantitative combination of the two techniques proves to be suitable for the identification of reliable marker elements which may be used for classification and provenance studies. With 3D micro-XRF, the three-dimensional nature, i.e. the depth-resolved elemental composition as well as density variations, of the samples was investigated and bromine could be identified as a suitable marker element. It is shown through a comparison of quantitative and semiquantitative values for the bromine content derived using both techniques that, for elements which are homogeneously distributed in the sample matrix, quantification with micro-XRF using a one-layer model is feasible. Thus, the possibility for routine provenance studies using portable micro-XRF instrumentation on a vast amount of samples, even on site, is obtained through this work. KW - Archaeometry KW - 3D X-ray spectroscopy PY - 2011 DO - https://doi.org/10.1021/ac2011262 SN - 0003-2700 SN - 1520-6882 VL - 83 IS - 16 SP - 6308 EP - 6315 PB - American Chemical Society CY - Washington, DC AN - OPUS4-25209 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina A1 - Pavlovic, Mato T1 - Ganzheitliche Zuverlässigkeit - Prüfung von Bauteilen mit komplexer Geometrie N2 - Selbst die modernsten ZfP-Systeme können, wenn sie bis an die Grenzen ihrer Möglichkeiten z. B. kleine Fehler zu finden beansprucht werden, nicht alle Fehler der gleichen Größe finden. Sogar wenn ein und derselbe Fehler mehrmals geprüft wird, wird er nicht immer gefunden. Deshalb wurde, besonders für solche Anwendungsfälle wo das Übersehen eines Fehlers zu schwerwiegenden Konsequenzen führt, das Konzept der Zuverlässigkeit der ZfP eingeführt. Das Konzept der BAM beinhaltet eine ganzheitliche Betrachtungsweise mittels eines modularen Models. Die Hauptmodule des Modells sind die innewohnende Fähigkeit, die die physikalisch technischen Aspekte behandelt. Weiterhin werden die Einflüsse der Umgebung betrachtet, die den Prüfprozess stören, aber nicht zum Prüfsystem selbst gehören. Einen wesentlichen Aspekt, sowohl bei manuellen als auch bei mechanisierten Prüfungen stellt der menschliche Faktor dar. Die Betrachtungen im vorliegenden Artikel beziehen sich hauptsächlich auf die innewohnende Fähigkeit. Wegen der dem Prüfprozess innewohnenden Unsicherheit wird die Leistungsfähigkeit eines ZfP-Systems durch eine Funktion POD (a) ausgedrückt. Zu verschiedenen Fehlergrößen (a) gehören verschiedene Fehlerauffindwahrscheinlichkeiten (POD). Die Fehlergröße (a), bei der die untere 95 % Vertrauensgrenze das Niveau von 90 % POD schneidet wird α90/95 genannt. Dieser Punkt wird als Maß für das Leistungsvermögen der ZfP-Methode benutzt. Während der letzten 10-20 Jahre wurden auf diese Weise verschiedene Inspektionssysteme für eine gewählte ZfP-Methode mit einer einfachen Anwendungsgeometrie bewertet. Wenn man über diese einfachen Anwendungssituationen hinaus, die Zuverlässigkeit in realen industriellen Prozessen betrachtet, treten als erstes industrielle Bauteile mit komplexer Geometrie und Defekte, die mit mehr als nur einem Parameter (Größe und Tiefe, Orientierung, Oberflächenrauhigkeit) charakterisiert werden müssen, auf die Tagesordnung. Neue hochentwickelte und automatisierte ZfP-Systeme, wie z. B. Ultraschallgruppenstrahler, lassen die Möglichkeit zu die Prüfungen digital aufzuzeichnen und später erst auszuwerten. Weiterhin erlauben es moderne Modellierungswerkzeuge den ZfP-Prozess zu simulieren und damit die Einflüsse der Wellenausbreitung und deren Wechselwirkung mit Defekten sowie die Wirkung der zusätzlichen Einflussparameter (z. B. Abstand vom Prüfkopf oder Orientierung) auf die POD zu untersuchen. Damit entsteht die Möglichkeit die räumliche Verteilung der POD im Prüfstück zu ermitteln – die Volumen-POD. Die Volumen-POD kann ebenso wie die konventionelle POD als Maß für die Leistungsfähigkeit des ZfP-Systems benutzt werden. Darüber hinaus kann man das ZfP-System optimieren. Wenn z. B. bestimmte Volumenelemente nur ungenügende POD-Werte aufweisen, müssen zusätzliche Prüfungen einbezogen werden. Aber auch der umgekehrte Fall, Bereiche in denen mehrere Prüfköpfe ein POD Niveau von 100 % haben und die Zahl der Prüfungen reduziert werden kann, werden mit der Volumen-POD erkannt. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Zuverlässigkeit KW - ZfP KW - Volumen-POD KW - Produkt-Design PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-251607 SN - 978-3-940283-33-7 VL - 127 SP - Mi.3.C.1 - 1 EP - 7 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25160 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija A1 - Gaal, Mate A1 - Müller, Christina A1 - Fahlbruch, B. A1 - Schombach, D. T1 - Einfluss des Zeitdrucks auf die manuelle Ultraschallprüfung. Untersuchung zu menschlichen Faktoren auf die Ergebnisse zerstörungsfreier Prüfungen N2 - Die übergeordnete Zielsetzung unserer Untersuchung bestand darin, am Beispiel von Prüfungen mit Ultraschall eine belastbare Aussage zum Einfluss der Arbeitsbedingungen des Prüfers auf die Qualität der Ergebnisse von zerstörungsfreien Prüfungen zu ermitteln und Möglichkeiten zur Minimierung ungünstiger Einflussfaktoren aufzuzeigen. Der Schwerpunkt der Untersuchung wurde auf die manuelle Ultraschallprüfung gelegt und der Faktor 'Zeitdruck' (in drei Stufen variiert) als die zu variierende physische Einflussgröße gewählt. Die Variation des Faktors Zeitdruck wurde gemäß dem Prozessmodell von der Erhebung psychologischer Faktoren, die das Individuum und die Organisation beschreiben, begleitet. Die Ultraschallprüfungen erfolgten mit zehn Prüfern am Großbehälter und an Vergleichskörpern mit eingebrachten Testfehlern (Nuten, Risse). Die ausgewählten Fehler waren typisch für Prüfaufgaben, die bei wiederkehrenden Ultraschallprüfungen in Kernkraftwerken von den Prüfern zu lösen sind. Die Prüfaufgabe bestand darin, die in den vorgegebenen Prüfabschnitten vorhandenen Reflektoren aufzufinden und deren Amplituden, Ortskoordinaten und Längenerstreckungen zu ermitteln. Als Bewertungsmaßstab für die Qualität der Prüfaussage und für den Einfluss des menschlichen Faktors diente die Präzision der gemessenen Werte. Die Ergebnisse zeigen einen hohen Einfluss des menschlichen Faktors auf das Prüfergebnis und eine Einwirkung des Zeitdrucks besonders auf die Präzision der Messwerte. Hierbei war die Wirkung des individuell wahrgenommenen Zeitdrucks zusammen mit der psychischen Arbeitsbeanspruchung signifikant. Es wurde unter anderem herausgearbeitet, dass durch eine gute Vorbereitung auf die Prüfung, z.B. durch die sorgfältige Einweisung und ein vorgeschaltetes Fertigkeitstraining an Vergleichskörpern, die Zuverlässigkeit der Prüfergebnisse verbessert werden kann. Insgesamt hatte der Faktor 'Organisation' neben der 'Erfahrung' einen hohen Einfluss auf das Leistungsvermögen der Prüfer. Die Projektergebnisse wurden im Abschlussbericht des Forschungsvorhabens SR2514 dargestellt, es wurden drei Empfehlungen zur Vorbereitung und Einweisung der Prüfer, zur Stärkung der Verantwortung der Prüfaufsicht und zum 4-Augen-Prinzip formuliert. Die Empfehlungen wurden in der KTA- Regel 3201.4 'Komponenten des Primärkreises von Leichtwasserreaktoren; Teil 4: Wiederkehrende Prüfungen und Betriebsüberwachung (RÄE Fassung 2010-11)', umgesetzt. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Human factors KW - ZfP KW - Ultraschallprüfung KW - UT KW - Zeitdruck PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-251610 UR - http://jt2011.dgzfp.de/Portals/jt2011/BB/mi2c3.pdf SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Mi.2.C.3) SP - 1 EP - 9 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-25161 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lischka, Susanne A1 - Körte, F. A1 - Faust, R. A1 - Nehls, Irene A1 - Piechotta, Christian T1 - Synthesis, characterization and application of a two-fold 13C-labeled calibration standard for the analysis of arsenobetaine using HPLC-ESI-MS/MS without high resolution mass spectrometry N2 - A procedure has been developed for the determination of arsenobetaine in fish matrix by HPLC–ESI-MS/MS. Hereby (trimethylarsonium)-1,2-13C-acetate (arsenobetaine) is used as internal calibration standard. Arsenobetaine was determined in a fish material (Sea Bass) with an expanded uncertainty of 3.8%. KW - Arsenobetaine KW - ESI-MS/MS KW - Isotopic labeled KW - 13C PY - 2011 DO - https://doi.org/10.1016/j.talanta.2011.07.047 SN - 0039-9140 VL - 85 IS - 4 SP - 1996 EP - 1999 PB - Elsevier CY - Amsterdam AN - OPUS4-25163 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nehls, Irene A1 - Koch, Matthias A1 - Piechotta, Christian T1 - Die HPLC im Spannungsfeld zwischen Normung und Forschung T2 - Festkolloquium zu Ehren Dr. H. Knauer (80. Geburtstag) CY - Berlin, Germany DA - 2011-09-13 PY - 2011 AN - OPUS4-25164 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tenzer, S. A1 - Docter, D. A1 - Rosfa, S. A1 - Wlodarski, A. A1 - Kuharev, J. A1 - Rekik, A. A1 - Knauer, S.K. A1 - Bantz, C. A1 - Nawroth, T. A1 - Bier, C. A1 - Sirirattanapan, J. A1 - Mann, W. A1 - Treuel, L. A1 - Zellner, R. A1 - Maskos, Michael A1 - Schild, H. A1 - Stauber, R.H. T1 - Nanoparticle size is a critical physico-chemical determinant of the human blood plasma corona: a comprehensive quantitative proteomic analysis N2 - In biological fluids, proteins associate with nanoparticles, leading to a protein 'corona' defining the biological identity of the particle. However, a comprehensive knowledge of particle-guided protein fingerprints and their dependence on nanomaterial properties is incomplete. We studied the long-lived ('hard') blood plasma derived corona on monodispersed amorphous silica nanoparticles differing in size (20, 30, and 100 nm). Employing label-free liquid chromatography mass spectrometry, one- and two-dimensional gel electrophoresis, and immunoblotting the composition of the protein corona was analyzed not only qualitatively but also quantitatively. Detected proteins were bioinformatically classified according to their physicochemical and biological properties. Binding of the 125 identified proteins did not simply reflect their relative abundance in the plasma but revealed an enrichment of specific lipoproteins as well as proteins involved in coagulation and the complement pathway. In contrast, immunoglobulins and acute phase response proteins displayed a lower affinity for the particles. Protein decoration of the negatively charged particles did not correlate with protein size or charge, demonstrating that electrostatic effects alone are not the major driving force regulating the nanoparticle–protein interaction. Remarkably, even differences in particle size of only 10 nm significantly determined the nanoparticle corona, although no clear correlation with particle surface volume, protein size, or charge was evident. Particle size quantitatively influenced the particle’s decoration with 37% of all identified proteins, including (patho)biologically relevant candidates. We demonstrate the complexity of the plasma corona and its still unresolved physicochemical regulation, which need to be considered in nanobioscience in the future. KW - Bionanoscience KW - Liquid chromatography mass spectrometry KW - Nanotoxicity KW - Nanomedicine KW - Immunology KW - Colloidal chemistry KW - Bioinformatics PY - 2011 DO - https://doi.org/10.1021/nn201950e SN - 1936-0851 VL - 5 IS - 9 SP - 7155 EP - 7167 PB - ACS Publ. CY - Washington, DC, USA AN - OPUS4-25167 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lang, Thomas A1 - Bantz, C. A1 - Bertin, Annabelle A1 - Maskos, Michael T1 - Study of protein-nanoparticle interactions with FFF and DLS: Concentration dependency of the aggregation process T2 - SPP1313 Workshop 5: The Nanoparticle-Protein Corona: Characterization, impact and biological relevance CY - Mainz, Germany DA - 2011-12-08 PY - 2011 AN - OPUS4-25168 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koshkina, Olga A1 - Bantz, C. A1 - Lang, Thomas A1 - Kasper, J. A1 - Kirkpatrick, C. J. A1 - Würth, Christian A1 - Resch-Genger, Ute A1 - Maskos, Michael T1 - Fluorescent Poly(organosiloxane) Nanoparticles in Biological Environment T2 - SPP1313 Workshop 5: The Nanoparticle-Protein Corona: Characterization, impact and biological relevance CY - Mainz, Germany DA - 2011-12-08 PY - 2011 AN - OPUS4-25169 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Beyer, Katrin A1 - Kannengießer, Thomas A1 - Griesche, Axel A1 - Schillinger, B. T1 - Neutron radiography study of hydrogen desorption in technical iron N2 - The purpose of the present study is to show the feasibility of examining hydrogen desorption in technical iron samples using neutron radiography at the ANTARES facility of the FRM II research reactor, Technische Universität München. It has been shown that this method is appropriate for in situ determination of hydrogen Desorption for concentrations as low as 20 ppmH. Experiments were carried out in the temperature range from room temperature up to 260 °C. Measurement was based on direct comparison between electrochemically hydrogen-loaded iron samples and hydrogen-free reference samples at the same temperature. This enables the determination of hydrogen concentration as a function of time and temperature. Ex situ carrier gas hot extraction experiments using the same temperature–time profiles as the neutron radiography experiments have been used to calibrate the greyscale values of the radiographs to defined hydrogen concentrations. It can be stated that hydrogen desorption correlates with sample temperature. KW - Neutron radiography KW - Hydrogen PY - 2011 DO - https://doi.org/10.1007/s10853-011-5450-7 SN - 0022-2461 SN - 1573-4803 VL - 46 IS - 15 SP - 5171 EP - 5175 PB - Springer Science + Business Media B.V. CY - Norwell, Mass. AN - OPUS4-25150 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Deubel, Jan A1 - Krüger, Simone A1 - Krause, Ulrich T1 - Analytische und numerische Untersuchungen zum materialspezifischen Brandverhalten als Basis für die Rekonstruktion von Bränden T2 - Doktorandentag, Universität Magdeburg; Lehrstuhl Anlagentechnik und Anlagensicherheit CY - Magdeburg, Germany DA - 09.12.2011 PY - 2011 AN - OPUS4-25152 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kappler, A. A1 - Paul, Andrea A1 - Amstaetter, K. A1 - Borch, T. A1 - Larese-Casanova, P. A1 - Jiang, J. A1 - Bauer, I. T1 - Arsenic redox transformation by humanic substances and Fe minerals T2 - Ninth International Symposium on the Geochemistry of the Earth's Sureface (GES-9) CY - Boulder, CO, USA DA - 2011-06-01 PY - 2011 AN - OPUS4-25154 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Paul, Andrea A1 - Eckert, W. A1 - Grossart, H.-P A1 - Weser, Aline T1 - Effects of UV generated ROS from Humic Substances on aquatic Organism T2 - Workshop Peat and Humic Substances CY - Zittau, Germany DA - 2011-09-28 PY - 2011 AN - OPUS4-25155 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Priebe, Nsesheye Susan A1 - Schmidt, W. T1 - Spearhead network for innovative, clean and safe cement and concrete technologies (SPIN) project in east, central and southern Africa T2 - 2nd Environmental cement Africa conference CY - Nairobi, Kenya DA - 2011-05-11 KW - SPIN KW - Africa KW - Cement KW - Concrete KW - Construction PY - 2011 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. SP - 1 EP - 3(?) AN - OPUS4-25156 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubcová, Petra A1 - Rübner, Katrin A1 - Schnell, A. T1 - Nachhaltige Verwertung von Bau- und Abbruchabfällen im Bausektor N2 - Mineralische Sekundärrohstoffe finden im Beton als Gesteinskörnung, Betonzusatzstoff, Bestandteil von Zementen oder Spezialbindemitteln Anwendung. Für den Einsatz von rezyklierten Gesteinskörnungen, Kesselsand, Steinkohlenflugasche, Silicastaub und Hüttensand bestehen bereits Normen bzw. bauaufsichtliche Zulassungen. Für weitere Reststoffe, wie Mauerwerkbruch und beim Baustoffrecycling anfallende feinkörnige, heterogene Sandfraktionen, existieren noch keine höherwertigen Verwertungswege. In einem Forschungsprojekt werden derzeit Möglichkeiten zur Verwertung von heterogenen mineralischen Bau- und Abbruchabfällen durch Herstellung von Blähgranulaten mit maßgeschneiderten Eigenschaften (Schüttdichte, Rohdichte, Korngröße und Kornfestigkeit) untersucht. Dies eröffnet die Möglichkeit einer rohstofflichen Verwertung solcher Abfälle. Im Mittelpunkt der Untersuchungen steht der Mauerwerkbruch. Er fällt mit über 20 Tonnen pro Jahr an und weist im Vergleich zum Betonbruch größere Verwertungsdefizite auf hl. Die erzeugten Granulate sollen als leichte Gesteinskörnung im Beton, Schüttung oder Pflanzsubstrat Anwendung finden. Die ersten Ergebnisse der Granulatherstellung mit einer thermischen Behandlung zeigen, dass sich Mauerwerkbruch als Rohstoff zur Herstellung leichter Gesteinskörnungen eignet 121. Die so erzeugten Blähgranulate weisen ähnliche Eigenschaften wie herkömmliche Blähtöne auf 131. Das Hauptziel der in diesem Beitrag vorgestellten weiteren Untersuchungen war, die Rohdichte der Granulate bei gleichbleibender oder steigender Kornfestigkeit zu senken. Aus energetischer Sicht des Blähprozesses wurde neben dem thermischen Verfahren auch die Möglichkeit einer hydrothermalen Erhärtung der Granulate untersucht. T2 - Jahrestagung der Fachgruppe Bauchemie - Nachhaltige Verwertung von Bau- und Abbruchabfällen im Bausektor CY - Hamburg-Harburg, Germany DA - 06.10.2011 KW - Sekundärrohstoffe KW - Sekundäre Gesteinskörnung KW - Recycling KW - Leichtbeton PY - 2011 SN - 978-3-936028-69-0 N1 - Serientitel: GDCh-Monographien – Series title: GDCh-Monographien VL - 44 SP - 121 EP - 125 CY - Frankfurt/M. AN - OPUS4-25157 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija A1 - Müller, Christina A1 - Kanzler, Daniel A1 - Fahlbruch, B. A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - 'Human factors' bei der Datenauswertung der zerstörungsfreien Prüfung am Beispiel der nuklearen Endlagerung N2 - Für eine ganzheitliche Betrachtung der Sicherheit bei der zerstörungsfreien Prüfung (ZfP) ist es unvermeidlich neben der Technik auch den Prüfer und die Prüforganisation einzubeziehen. Die Prüfung der Unversehrtheit von Endlagerbehältern ist eine eine sicherheitstechnisch wichtige Anwendung. Die Betreiber der geplanten finnischen und schwedischen Endlager, Posiva und SKB, kapseln den radioaktiven Abfall in Kupferkanistern ein und deponieren die Kanister dann in Felsgestein in einer Tiefe von ca. 500m. Die Kanister bestehen aus einem zylinderförmigen Kupfermantel mit einem Deckel und einem Boden, die zusammen die Außenumhüllung ergeben sowie einer Gusseisenmatrix für die Brennstäbe. Alle Komponenten werden auf ihre Dichtheit bzw. strukturelle Unversehrtheit mittels zerstörungsfreier Prüfmethoden geprüft, um sicher zu stellen, dass im Material und in den Schweißnähten keine kritischen Defekte vorhanden sind, die zu Freisetzungen in die Umgebung führen könnten. Vier ZfP Methoden (Ultraschall-, Wirbelstrom- und radiographische Prüfung, und die visuelle Prüfung anhand einer Kamera) werden mechanisiert durchgeführt, die gewonnenen Daten werden von qualifizierten Fachleuten ausgewertet und bieten so die Möglichkeit, dass Fehler entstehen. Das 'Human Factor'- Untersuchungskonzept besteht aus der Identifizierung potenzieller menschlicher Fehler, deren Ursachen und Präventionsmethoden. Mit Hilfe einer abgewandelten FMEA (Failure Modes and Effects Analysis) wurden mögliche Risiken identifiziert, die die Wahrscheinlichkeit für das Auftreten menschlicher Fehler bei der Datenauswertung erhöhen. Einige dieser Risiken sind beispielsweise Verantwortungsdiffusion beim 4-Augen-Prinzip, Übervertrauen in die Technik bei der automatischen Identifikation von Defekten sowie der Aufmerksamkeitsverlust bei dynamischer Bildbetrachtung. Deren Wirkung wird derzeit experimentell überprüft, um Ansatzpunkte für Optimierungen zu ermitteln und damit die Gesamtzuverlässigkeit des Systems zu verbessern. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Human factors KW - UT KW - ET KW - ZfP KW - Nukleare Endlagerung PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-251584 UR - http://jt2011.dgzfp.de/Portals/jt2011/BB/p42-ku~1.pdf SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (P 42) SP - 1 EP - 2 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25158 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kanzler, Daniel A1 - Müller, Christina A1 - Pitkänen, J. T1 - Konzept für den Einsatz der Bayes'schen Statistik: In der Zuverlässigkeitsbestimmung von zerstörungsfreien Diagnosesystemen - Das Problem zu kleiner experimenteller Datenmengen N2 - Die statistische Qualitätskennzahl 'Probability of Detection (POD)' hängt von der Anzahl der zugrunde liegenden, brauchbaren Ergebnisse ab. Ist die Datenmenge niedrig, so ist auch die Aussage der POD eher beschränkt. Dennoch heißt eine große Zahl von Daten, nicht gleichzeitig, dass die POD für den realen Einsatz in der Produktion genügt. Es muss unterschieden werden, auf welcher Basis – unter welchen konkreten Bedingungen - die Daten erhoben wurden. Als wichtigste Ergebnisse zählen die Messergebnisse aus der Produktion der später verwendeten Prüfobjekte für den konkreten Einsatz. Noch bevor die zerstörungsfreien Prüfmethoden zuverlässig in der Produktion eingesetzt wurde, muss jedoch nachgewiesen werden, dass die real vorkommenden Fehler gefunden werden können. Das bedeutet, zu einem Zeitpunkt, an dem noch nicht ausreichend Daten vorhanden sind. Während für die realistische Prüfung die notwendige Anzahl der verschiedenen Fehler meist nicht erreicht wird, so fehlen bei der Bewertung der künstlichen Fehler wichtige Parameter und Einflussgrößen. Es muss somit eine Zwischenlösung gesucht werden, in der die Informationen von beiden Prüfungen kombiniert werden. Mit der Bayes’schen Statistik ermöglicht die Mathematik diese Informationen miteinander zu kombinieren und somit beide Informationen mit in die Bewertung einfließen zu lassen. Praktisch angewandt und erprobt wird die Vorgehensweise gemeinsam mit der Firma POSIVA, die sich mit dem Bau eines Endlagers für hoch-radioaktiven Abfall in Finnland beschäftigt. Hier wird als eine der technischen Barrieren ein Kupferbehälter für die Aufbewahrung der verbrauchten Brennstäbe genutzt. Dieser Kupferbehälter wird mit mehreren zerstörungsfreien Prüfmethoden geprüft. Anhand von Radiographiedaten wird gezeigt, dass die Aussagekraft der realistischen Fehlerdaten mit Hilfe der künstlichen Referenzfehlerdaten untermauert werden kann. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Bayes'sche Statistik KW - POD KW - Fehlende Datenmenge PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-251598 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Mi.3.C.3) SP - 1 EP - 9 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25159 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Das neue EVPG und aktueller Sachstand bei den Durchführungsvorschriften T2 - 1. Jahrestagung Marktüberwachung Baden-Württemberg CY - Herrenberg, Germany DA - 2011-12-14 PY - 2011 AN - OPUS4-25140 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fontana, Patrick A1 - Müller, Urs A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Schädigungsmechanismen in Beton T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Frost-Tausalz-Beanspruchung KW - Schrumpfrisse KW - Autogenes Schwinden KW - Plastisches Schwinden KW - Brand KW - Sulfatangriff KW - AKR PY - 2011 SN - 978-3-9814281-0-0 IS - D1 SP - 105 EP - 110 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25141 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schilder, Constanze A1 - Hofmann, Detlef A1 - Kohlhoff, Harald A1 - Habel, Wolfgang ED - Ramos, G. A. T1 - Structure-integrated fiber-optic strain wave sensor for concrete pile testing and monitoring N2 - Reinforced concrete piles are used in case of structures that are constructed on soft ground to transfer the loads into deeper strata with sufficient bearing capacity. In order to determine the pile’s behavior and possible damage, static and dynamic pile tests are carried out. Dynamic measurements taken from the pile head can show the bearing behavior and structural integrity by using the theory of wave propagation. In order to receive more precise information about the pile features, now, a string of sensors is embedded at different levels of the pile. A fiber optic strain wave sensor, based on the extrinsic Fabry-Perot interferometer (EFPI), has already been developed and tested in full-scale field tests by Schallert (2010). It was possible to detect the introduced deformation caused by the static load and the dilatational wave during dynamic loading. Although the full-scale tests were successful, the engineering design of the sensor body left room - from the economical point of view - to be optimized. After laboratory tests with the optimized sensor, a cast-in-situ bored pile has been built at the BAM Test Site Technical Safety in Horstwalde, South of Berlin. Additionally to the EFPI sensors, fiber Bragg grating (FBG) sensors, temperature sensors and resistance strain gauge (RSG) sensors are embedded in order to compare the signals with each other. In this paper, the modified sensor and the Setup of the cast-in-situ bored pile along with results of dynamic tests are shown. T2 - SHMII-5 - 5th International conference on structural health monitoring of intelligent infrastructure CY - Cancún, Mexico DA - 11.12.2011 KW - Fibre optic sensors KW - Monitoring KW - Concrete pile KW - Foundation KW - Integrity testing PY - 2011 IS - Topic_04.Cat_4.2-abs002 SP - 1 EP - 8 PB - National Autonomous University of Mexico CY - Mexico City AN - OPUS4-25142 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Koshkina, Olga A1 - Bantz, C. A1 - Würth, Christian A1 - Lang, Thomas A1 - Resch-Genger, Ute A1 - Maskos, Michael T1 - Fluorophore-labeled siloxane-based nanoparticles for biomedical applications N2 - We present the synthesis and characterization of multifunctional fluorophore-labeled poly(organosiloxane) nanoparticles with core-shell architecture, where the fluorescent dye is incorporated into the core. Grafting of heterobifunctional poly(ethylene oxide) (PEO) onto the particle surface leads to water-soluble biocompatible nanoparticles. Two different strategies have been used for the synthesis: The encapsulation of dye-labeled monomers during the polycondensation with additional PEO coating and subsequent dye labeling by covalent attachment of the fluorescent dye rhodamine B to the (chloromethylphenyl)siloxane groups in the core after polymerization and grafting of PEO onto the surface. Comparison of the fluorescence quantum yields of the nanoparticles before and after PEO coating show a decrease in quantum yield after PEO coating. KW - Biocompatibility KW - Core-shell KW - Fluorescence KW - Fluorescence quantum yield KW - Nanoparticles KW - PEO PY - 2011 DO - https://doi.org/10.1002/masy.201100041 SN - 1022-1360 SN - 0258-0322 SN - 1521-3900 VL - 309/310 IS - 1 SP - 141 EP - 146 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-25143 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Regina A1 - Maierhofer, Christiane A1 - Kreutzbruck, Marc A1 - Schilling, M. T1 - Numerical method of active thermography for the reconstruction of back wall geometry N2 - The paper presents numerical methods to detect and classify defects and inhomogeneities by means of active thermography. The objective is to determine the wall thickness of structure elements with an inaccessible back wall, for example, of pipes or Containers. As test specimens we used approximately 2 cm thick PVC samples with spatial variations in the back wall geometry. Flash lamps provided the heating. To know the thickness of the wall, we used two inversion methods and compared the results achieved. One is an iterative echo defect shape method and already tested on Steel test specimens with good reconstruction results. The second one is the Levenberg-Marquardt method, applied here to thermographic data for non-destructive testing. Since data capturing using active thermography and the presented numerical methods can easily be automated, the combination of these two procedures is a promising approach providing a broad area of application. T2 - 6th Workshop 'NDT in progress' CY - Prague, Czech Republic DA - 10.10.2011 KW - Impulse-thermography KW - Inversion KW - Levenberg-Marquardt method KW - Echo defect shape KW - Defect shape reconstruction PY - 2011 SN - 978-80-214-4339-6 IS - Chapter 8 SP - 245 EP - 252 AN - OPUS4-25144 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldmann, Ines A1 - Torge, Manfred T1 - Veränderungen an korrodierten Glasoberflächen zwischen 1994 und 2010 T2 - Abschlussveranstaltung des DBU-Evaluierungsprojektes CY - Stendal, Germany DA - 2011-06-08 PY - 2011 AN - OPUS4-25145 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Torge, Manfred A1 - Feldmann, Ines A1 - Braun, Ulrike A1 - Wachtendorf, Volker T1 - Untersuchungen zu Schadensphänomenen an Außenschutzverglasungen aus Verbundsicherheitsglas T2 - Abschlussveranstaltung des DBU-Evaluierungsprojektes CY - Stendal, Germany DA - 2011-06-08 PY - 2011 AN - OPUS4-25146 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Torge, Manfred A1 - Feldmann, Ines T1 - Simulation von Staubbelastungen im Klimaschrank und Wirkung auf Gläser historischer Zusammensetzung T2 - Abschlussveranstaltung des DBU-Evaluierungsprojektes CY - Stendal, Germany DA - 2011-06-08 PY - 2011 AN - OPUS4-25147 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völz, Uwe A1 - Mrasek, Heinz A1 - Heckel, Thomas T1 - Querfehlerprüfung an anisotopen Engspaltschweißnähten mit Gruppenstrahlern T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-25220 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weinhart, M. A1 - Becherer, T. A1 - Schnurbusch, N. A1 - Schwibbert, Karin A1 - Kunte, Hans-Jörg A1 - Haag, R. T1 - Linear and hyperbranched polyglycerol derivatives as excellent bioinert glass coating materials N2 - The non-specific adsorption of proteins to surfaces in contact with biofluids constitutes a major problem in the biomedical and biotechnological field, due to the initiation of biofilm formation and the resulting improper function of devices. Therefore, non-fouling surfaces modified with poly(ethylene glycol) (PEG) are usually applied. In this study, we report the synthesis of triethoxysilane modified glycerol based polymers of linear and branched architecture for the preparation of covalently attached monolayers on glass. Evaluation of the biocompatibility of these surfaces was performed in comparison to bare non-coated glass, hydrophobic hexadecane modified glass, and mPEG modified glass as the controls. Protein adsorption of BSA and fibrinogen (1 mg · mL-1 in PBS) after 4 and 24 h immersion was reduced by more than 96 and 90%, respectively, compared to the adsorption on bare glass substrates. In addition, mouse NIH-3T3 fibroblast cells showed only marginal adhesion on the polyglycerol and mPEG coated slides after 3 and 7 d incubation in cell suspension, which demonstrates the long-term stability of the applied glass coatings. The non-adhesive properties of these coatings were further reflected in bacterial adhesion tests of Escherichia coli K12 and three clinically relevant Gram-positive and negative strains (Staphylococcus aureus, Pseudomonas aeruginosa, and Aeromonas hydrophila), since linear polyglycerol (LPG(OH)), linear poly(methyl glycerol) (LPG(OMe)), and hyperbranched polyglycerol (HPG) reduced the adhesion for all tested strains by more than 99% compared to bare glass. Therefore, polyglycerol derivatives present an excellent non-fouling surface coating as an alternative to PEG with feasibility for surface modification of various substrates. KW - Protein adsorption KW - Non-fouling-surfaces KW - Linear polyglycerol KW - Hyperbranched polyglycerol KW - Bacterial adhesion PY - 2011 DO - https://doi.org/10.1002/adem.201180012 SN - 1438-1656 VL - 13 IS - 12 SP - B501 EP - B510 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-25221 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rahman, Mehbub-Ur A1 - Kolkoori, Sanjeevareddy A1 - Prager, Jens T1 - Elastische Wellenausbreitung in austenitischen Schweißnähten - numerische Simulationen und deren messtechnische Validierung N2 - In diesem Beitrag wird die numerische Modellierung und deren messtechnische Validierung der elastischen Wellenausbreitung in austenitischen Schweißnähten vorgestellt. Die Ultraschallprüfung von austenitischen Schweißverbindungen war und ist immer noch eine der schwierigsten Aufgaben der ZfP. Für eine optimierte Prüfkonfiguration ist es notwendig, verschiedene Prüfparameter wie Einschallwinkel, Prüfkopfposition und -Orientierung richtig einzustellen. Um die beste Anordnung zu ermitteln, wurde die Schallausbreitung in den austenitischen Schweißnähten mit verschiedenen Verfahren wie elastische finite Integrationstechnik (EFIT) und Raytracing simuliert. Mit Hilfe der Simulationsergebnisse wurde die verwendete Gruppenstrahlerprüftechnik optimiert. Es wurden zahlreiche Untersuchungen an anisotropen Testkörpern in V-Durchschallung und an bezüglich der Schweißnaht transversal orientierten Rissen durchgefühlt. Die Ergebnisse der auf Raytracing bzw. EFIT basierenden Simulationstools wurden untereinander und auch mit den Messergebnissen verglichen. T2 - DAGA 2011 - 37. Jahrestagung für Akustik - Fortschritte der Akustik CY - Düsseldorf, Deutschland DA - 21.03.2011 PY - 2011 SN - 978-3-939296-02-7 SP - 1 EP - 2 AN - OPUS4-25224 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gardei, André A1 - Müller, Urs T1 - Anti-Graffiti-Systeme auf Beton: Wirkung und Leistungsfähigkeit T2 - 52. DAfStb-Forschungskolloquium 2011, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25225 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meng, Birgit A1 - Müller, Urs A1 - Fontana, Patrick T1 - Neue Erkenntnisse und Analysemethoden zum Phasenbestand und Gefüge des Zementsteins T2 - 52.DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25226 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völz, Uwe T1 - Visualisierung der Schallausbreitung in Festkörpern mit elektrodynamischen Sonden N2 - Die Prinzipien der Ultraschallausbreitung in festen Medien sind seit langem bekannt und können heute durch mathematische Modelle recht umfassend beschrieben und simuliert werden. In der Praxis zeigt sich aber, dass gerade bei komplexen Geometrien, sowie inhomogenen und anisotropen Materialien die Modelle immer noch an ihre Grenzen stoßen. Das ist insbesondere in der fehlenden Möglichkeit begründet, die akustischen Eigenschaften inhomogener Prüfgegenstände vollständig mathematisch zu beschreiben. Deshalb wird in letzter Zeit verstärkt nach Techniken gesucht, mit denen man die Schallausbreitung in solchen Materialien messen und anschaulich darstellen kann. Ziel dieser Entwicklung ist es, die Schallausbreitung in Festkörpern, insbesondere in solchen mit akustisch anisotropen Eigenschaften, besser zu verstehen und die Möglichkeit zu schaffen, die Simulationsrechnungen am realen Objekt zerstörungsfrei verifizieren zu können. In der Literatur werden verschiedene Methoden zur messtechnischen Visualisierung der Ultraschallausbreitung in Festkörpern beschrieben. Am bekanntesten sind optische Verfahren wie die Schlierentechnik, die schon seit langem genutzt wird, um den momentanen Schallfeldverlauf im Inneren von optisch transparenten Materialien sichtbar zu machen. Heute kommen verstärkt lasertechnische Methoden, wie z. B. das Laserinterferometer, zum Abtasten von nicht transparenten Materialoberflächen zum Einsatz. Da diese Verfahren mit einem hohen technischen Aufwand verbunden sind, werden häufig auch einfachere Methoden, wie z. B. das Abtasten mit punktförmigen piezoelektrischen Aufnehmern, verwendet. T2 - DAGA 2011 - 37. Jahrestagung für Akustik - Fortschritte der Akustik CY - Düsseldorf, Germany DA - 21.03.2011 KW - Ultraschall KW - Schallfeld KW - Elektrodynamische Sonde KW - Visualisierung PY - 2011 SN - 978-3-939296-02-7 SP - 347 EP - 348 PB - Deutsche Gesellschaft für Akustik CY - Berlin AN - OPUS4-25227 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pistol, Klaus A1 - Weise, Frank A1 - Meinel, Dietmar A1 - Meng, Birgit T1 - Zur Wirkungsweise von PP-Fasern in brandbeanspruchten Hochleistungsbetonen T2 - 52. DAfStb-Forschungskolloquium 2011, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25228 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brandt, S. A1 - Müller, Birgit A1 - Müller, D. A1 - Horn, Wolfgang A1 - Panasková, J. A1 - Plehn, W. T1 - Messung und Bewertung von Gerüchen aus Bauprodukten für den Innenraum T1 - Measurement and evaluation of odour emissions from building products for indoor usage N2 - Messung und Bewertung von Gerüchen aus Bauprodukten für den Innenraum gewinnen vor allem durch den zunehmenden Bau energieeffizienter Gebäude an Bedeutung. Intensive und unangenehme Gerüche werden von Bewohnerinnen, Bewohnern und Angestellten nicht akzeptiert und können auf Dauer krank machen. Bislang stand noch kein allgemein anerkanntes Messverfahren zur Verfügung. Dieses wurde nun in Forschungsprojekten entwickelt, wobei auch konkrete Bewertungsvorschläge zur Zumutbarkeit von Gerüchen gemacht wurden. Das Verfahren ist an die Messung der Emissionen flüchtiger organischer Verbindungen aus Bauprodukten gekoppelt und nutzt Probanden, um die Geruchsstärke (Intensität) und den Geruchseindruck (Hedonik) zu ermitteln. In der Praxis wird das Verfahren nun an verschiedenen Stellen erprobt. Die Bewertung der Geruchsemissionen gibt der Industrie die Möglichkeit, geruchsarme Produkte zu gestalten. Die Kennzeichnung geruchsarmer Bauprodukte mit dem Umweltzeichen Blauer Engel erleichtert Verbraucherinnen und Verbrauchern die Orientierung beim Einkauf. N2 - Measuring and evaluating odour emissions from building products used in indoor spaces are becoming increasingly important for the construction of energy-efficient buildings. Intensive and unpleasant smells are not accepted by inhabitants and employees and may lead to negative health effects. Up to now a consistent measuring method for odour emissions has not been available. A measuring method and also concrete standards for the assessment of odours by using reasonableness of smells have now been developed in succeeding research projects. The procedure uses a panel of test persons to determine the strength (intensity) and impression (hedonic appraisal) of odour and is linked to the already well established measurement of the emission of volatile organic compounds from building products. At the Moment the new procedure is tested in practice at different laboratories. Evaluating odour emissions helps manufacturers to develop products with low or very low odour emissions. The labeling of low-odour Building products with the environmental label Blue Angel gives consumers an orientation for purchase. KW - Labelsysteme KW - VOC KW - Geruch KW - Geruchstest KW - Emissionsmessungen PY - 2011 SN - 2190-1120 SN - 2190-1147 VL - 4 SP - 50 EP - 58 PB - BfS CY - Berlin AN - OPUS4-25210 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neubauer, Andreas A1 - Reimund, Verena A1 - Pelkner, Matthias A1 - Erthner, Thomas A1 - Bertus, Norbert A1 - Thomas, Hans-Martin A1 - Kreutzbruck, Marc T1 - BIMAS - Bildgebende Verfahren und Komponenten für die zerstörungsfreie Materialprüfung unter Einsatz magnetischer Sensorarrays T2 - Öffentliche Statuspräsentation der Verbundprojekte der Bekanntmachung "Magnetische Mikro- und Nanotechnologien" des BMBF CY - Nuremberg, Germany DA - 2011-06-09 PY - 2011 AN - OPUS4-25212 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neubauer, Andreas A1 - Pelkner, Matthias A1 - Reimund, Verena A1 - Erthner, Thomas A1 - Thomas, Hans-Martin A1 - Kreutzbruck, Marc T1 - NDT-adapted GMR probe with local magnetization unit for MFL testing T2 - 15th International Symposium on Applied Electromagnetics and Mechanics (ISEM 2011) CY - Naples, Italy DA - 2011-09-06 PY - 2011 AN - OPUS4-25213 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neubauer, Andreas A1 - Pelkner, Matthias A1 - Reimund, Verena A1 - Erthner, Thomas A1 - Bertus, Norbert A1 - Thomas, Hans-Martin A1 - Kreutzbruck, Marc T1 - BIMAS - Bildgebende Verfahren und Komponenten für die zerstörungsfreie Materialprüfung unter Einsatz magnetischer Sensorarrays T2 - Öffentliche Statuspräsentation der Verbundprojekte der Bekanntmachung "Magnetische Mikro- und Nanotechnologien" des BMBF CY - Nuremberg, Germany DA - 2011-06-09 PY - 2011 AN - OPUS4-25214 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kreutzbruck, Marc A1 - Daschewski, Maxim A1 - Harrer, Andrea A1 - Prager, Jens A1 - Guderian, Matthias A1 - Meyer-Plath, Asmus T1 - Carbon nanomaterials as broadband airbone ultrasound transducer T2 - International Ultrasonics Symposium (IEEE 2011) CY - Orlando, FL, USA DA - 2011-10-18 PY - 2011 AN - OPUS4-25215 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Harrer, Andrea A1 - Prager, Jens A1 - Kreutzbruck, Marc A1 - Guderian, Matthias A1 - Meyer-Plath, Asmus T1 - Erzeugung von Luftultraschall mit mikro- und nanostrukturierten Kohlenstoffmaterialien unter Ausnutzung des Themoakustischen Prinzips T2 - Jahrestagung für Akustik (DAGA 2011) CY - Düsseldorf, Germany DA - 2011-03-21 PY - 2011 AN - OPUS4-25216 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Boehm, Rainer A1 - Müller, Christina A1 - Pavlovic, Mato A1 - Ronneteg, U. T1 - Multi-Parameter POD in industriellen Anwendungen T2 - Seminar des Fachausschusses Ultraschallprüfung der DGZfP CY - Offenbach am Main, Germany DA - 2011-11-09 PY - 2011 AN - OPUS4-25217 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dey, Anika T1 - Squat Investigations and Detection of Squats with Eddy Current Testing T2 - 2nd International Squat Workshop CY - Leoben, Austria DA - 2011-11-09 PY - 2011 AN - OPUS4-25218 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dey, Anika A1 - Pohl, Rainer A1 - Thomas, Hans-Martin T1 - Erfahrungen mit der Wirbelstromprüfung beim Einsatz an unterschiedlichen Schienenstahlgüten T2 - ZfP Workshop "Zerstörungsfreie Prüfung von Schienen bei der Herstellung und im Betrieb" CY - Leoben, Austria DA - 2011-01-26 PY - 2011 AN - OPUS4-25219 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fontana, Patrick ED - Rogge, A. ED - Meng, B. T1 - Frühe Rissbildung in Beton durch plastisches Schwinden T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Germany DA - 07.11.2011 KW - Kapillardruck KW - Plastisches Schwinden KW - Schrumpfrisse KW - Faserbewehrung KW - Prüfverfahren PY - 2011 SN - 978-3-9814281-0-0 SP - 111 EP - 125 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25190 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weise, Frank ED - Rogge, A. ED - Meng, B. T1 - Neuartige Prüfmethodologien zur Schadensanalyse in Betonen T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Beton KW - Schädigungsprozesse KW - Schallemissionsanalyse KW - Ultraschall KW - Röntgen 3D-Computertomographie KW - Photogrammetrie PY - 2011 SN - 978-3-9814281-0-0 SP - 67 EP - 85 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25191 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Rheologie von Instandsetzungsmörteln - aktuelle Untersuchungen mit dem Würpelgerät T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Germany DA - 07.11.2011 PY - 2011 SN - 978-3-9814281-0-0 SP - 58 EP - 66 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-25192 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vasilic, Ksenija A1 - Kühne, Hans-Carsten A1 - Meng, Birgit A1 - Roussel, N. ED - Rogge, A. ED - Meng, B. T1 - Modelling of fresh SCC flow through reinforced sections T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 PY - 2011 SN - 978-3-9814281-0-0 SP - 50 EP - 57 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25193 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann, Christian A1 - Fontana, Patrick A1 - Müller, Urs A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Entwicklung von C-S-H-Phasen in autoklaviertem Ultra-Hochleistungs-Beton (UHPC) T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 PY - 2011 SN - 978-3-9814281-0-0 SP - 25 EP - 32 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25196 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meng, Birgit A1 - Müller, Urs A1 - Fontana, Patrick ED - Rogge, A. ED - Meng, B. T1 - Neue Erkenntnisse und Analysemethoden zum Phasenbestand und Gefüge des Zementsteins T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Baustoffe KW - Zement KW - Mörtel KW - Mineralogische Zusammensetzung PY - 2011 SN - 978-3-9814281-0-0 SP - 11 EP - 17 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25198 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Voland, Katja A1 - Weise, Frank A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Untersuchung des Einflusses der Gefügedichte von Betonen auf die AKR mit neuartiger Prüftechnik T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Alkali-Kieselsäure-Reaktion KW - Nebelkammerlagerung bei 40° C KW - 60° C-Betonversuch KW - Dehnungsmessung KW - Schallemissionsanalyse KW - Ultraschallgeschwindigkeit KW - mu-3D-CT PY - 2011 SN - 978-3-9814281-0-0 SP - 86 EP - 95 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25199 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten ED - Rogge, A. ED - Meng, B. T1 - 'Instandhaltung' - aktuelle Themen beim Schutz und Instandsetzen von Betonbauteilen T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 PY - 2011 SN - 978-3-9814281-0-0 SP - 216 EP - 226 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25180 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Recknagel, Christoph ED - Rogge, A. ED - Meng, B. T1 - Dauerhafter Schutz von Ingenieurbauwerken aus Beton - Was können Abdichtungssysteme leisten? T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 PY - 2011 SN - 978-3-9814281-0-0 SP - 204 EP - 215 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25181 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Urs A1 - Kargol, Marta A1 - Gardei, André ED - Rogge, A. ED - Meng, B. T1 - Der Einfluss der Zementart auf die Leistungsfähigkeit von Hydrophobierungsmitteln T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 PY - 2011 SN - 978-3-9814281-0-0 SP - 186 EP - 193 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25183 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Urs ED - Rogge, A. ED - Meng, B. T1 - Schutz von Beton: Aktuelle Forschung zur Wirkungsweise und Dauerhaftigkeit von Schutzmaßnahmen T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 PY - 2011 SN - 978-3-9814281-0-0 SP - 182 EP - 185 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25184 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Huismann, Sven A1 - Korzen, Manfred A1 - Weise, Frank A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Betonabplatzungen unter Feuerangriff und der Einfluss von Polypropylenfasern auf die Mikrorissbildung T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Germany DA - 07.11.2011 PY - 2011 SN - 978-3-9814281-0-0 SP - 163 EP - 171 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-25185 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Huismann, Sven A1 - Korzen, Manfred A1 - Rogge, Andreas ED - Rogge, A. ED - Meng, B. T1 - Stahlbetonstützen aus hochfestem Beton unter Brandbeanspruchung und die Anwendung allgemeiner Rechenverfahren T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Germany DA - 07.11.2011 PY - 2011 SN - 978-3-9814281-0-0 SP - 154 EP - 162 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-25186 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Urs A1 - Meng, Birgit A1 - Bürgisser, Philip ED - Rogge, A. ED - Meng, B. T1 - Das natürliche Puzzolan 'Rheinischer Trass' und dessen Einfluss auf eine Alkali-Kieselsäure-Reaktion (AKR) in Beton T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 PY - 2011 SN - 978-3-9814281-0-0 SP - 141 EP - 150 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25187 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pistol, Klaus A1 - Weise, Frank A1 - Meinel, Dietmar A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Zur Wirkungsweise von Polypropylen-Fasern in brandbeanspruchten Hochleistungsbetonen T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Polypropylen-Fasern KW - Hochfester Beton KW - Schallemissionsanalyse KW - Röntgen 3D-Computertomographie KW - Rasterelektronenmikroskopie PY - 2011 SN - 978-3-9814281-0-0 SP - 134 EP - 140 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25188 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pirskawetz, Stephan A1 - Weise, Frank A1 - Fontana, Patrick ED - Rogge, A. ED - Meng, B. T1 - Zwangsinduzierte Rissbildung bei erhärtendem Hochleistungsbeton T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Hochleistungsbeton KW - Hydratation KW - Autogenes Schwinden KW - Rissbildung KW - Schallemission KW - Ultraschall KW - Kapillardruck PY - 2011 SN - 978-3-9814281-0-0 SP - 126 EP - 133 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25189 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingbeil, Dietmar A1 - Klinger, Christian A1 - Bettge, Dirk A1 - Häcker, Ralf A1 - Heckel, Thomas A1 - Gohlke, Dirk T1 - Schadensanalyse zum Radsatzwellenbruch ICE 3 T2 - 43. Tagung des DVM-Arbeitskreis Bruchvorgänge 2011 CY - Rostock, Germany DA - 2011-02-22 PY - 2011 AN - OPUS4-25170 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterhus, Lennart A1 - Rübner, Katrin ED - Rogge, A. ED - Meng, B. T1 - Potenziale SiO2-reicher Filterschlämme für den Einsatz in hydraulischen Bindemitteln T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Germany DA - 07.11.2011 PY - 2011 SN - 978-3-9814281-0-0 SP - 328 EP - 335 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25171 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubcová, Petra A1 - Rübner, Katrin A1 - Schnell, A. ED - Rogge, A. ED - Meng, B. T1 - Blähgranulate aus Bau- und Abbruchabfällen als leichte Gesteinskörnung für Beton T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Sekundärrohstoffe KW - Sekundäre Gesteinskörnung KW - Recycling KW - Leichtbeton PY - 2011 SN - 978-3-9814281-0-0 SP - 318 EP - 327 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25173 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan A1 - Rübner, Katrin A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Ganzheitliche Bewertung der Einsatzmöglichkeiten von Sekundärrohstoffen in Beton T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Germany DA - 07.11.2011 PY - 2011 SN - 978-3-9814281-0-0 SP - 295 EP - 307 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25174 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rübner, Katrin A1 - Herbst, Tristan A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Ressourcenschonung durch Reststoffverwertung im Betonbau T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Germany DA - 07.11.2011 PY - 2011 SN - 978-3-9814281-0-0 SP - 283 EP - 294 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-25175 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Vogler, Nico A1 - Gardei, André A1 - Kühne, Hans-Carsten ED - Rogge, A. ED - Meng, B. T1 - Laserbasiertes Messverfahren zur Rautiefe-Bestimmung T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Rauheit KW - Rautiefe KW - Volumetrische Methode KW - Sandflächenverfahren KW - Laserverfahren KW - Linienlaser PY - 2011 SN - 978-3-9814281-0-0 SP - 256 EP - 261 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25176 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Entwicklung von modularen Instandsetzungsmörteln für den Einsatz an denkmalgeschützten Natursteinbauwerken T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Germany DA - 07.11.2011 PY - 2011 SN - 978-3-9814281-0-0 SP - 247 EP - 255 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-25177 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - MODINSYS - Entwicklung und Modifikation von Instandsetzungsmörteln für Beton- und Stahlbetonkonstruktionen T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Germany DA - 07.11.2011 PY - 2011 SN - 978-3-9814281-0-0 SP - 238 EP - 246 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-25178 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ünal, Murat A1 - Kühne, Hans-Carsten ED - Rogge, A. ED - Meng, B. T1 - Reparaturmörtel und Instandsetzungstechniken zur Restaurierung von Betonverglasungen T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 PY - 2011 SN - 978-3-9814281-0-0 SP - 227 EP - 237 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25179 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Poli, Marco A1 - Grätz, Rainer A1 - Arndt, Detlef A1 - Scheider, Swen A1 - Schröder, Volkmar T1 - Influence of the explosion-induced turbulence during venting on the pressure development T2 - 8th European Congress of Chemical Engineering (ECCE 2011) together with ProcessNet-Annual Meeting CY - Berlin, Germany DA - 2011-09-25 PY - 2011 AN - OPUS4-24478 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Einfluss ausgewählter Modifikationen der Mischungszusammensetzung auf die Eigenschaften von Instandsetzungsmörteln N2 - Trotz der zahlreichen Möglichkeiten zur Beeinflussung der Mörteleigenschaften durch Mischungsmodifikationen ist es nahezu unmöglich, einzelne Eigenschaften unabhängig von anderen zu verändern. Bei einer Mischungsoptimierung muss im Einzelfall immer entschieden werden, welcher der gewünschten Eigenschaften die höchste Priorität zukommt. Anhand von Parameterstudien wird im vorliegenden Artikel verdeutlicht, wie es für bestimmte Anwendungen sinnvoll sein kann, die Verschlechterung einzelner Eigenschaften zu akzeptieren, wenn dadurch eine für den speziellen Einsatzfall essenzielle Eigenschaft verbessert werden kann. Die komplexen Wechselwirkungen der einzelnen Bestandteile fuhren dazu, dass auch scheinbar widersprüchliche Kombinationen von Zusatzmitteln im Einzelfall erforderlich werden können. Zur Anpassung der meisten Mörteleigenschaften gibt es verschiedene Möglichkeiten der Zielerreichung mit jeweils unterschiedlichen Nebeneffekten. Frisch- und Festmörteleigenschaften sind dabei gleichermaßen zu beachten. KW - Instandsetzungsmörtel KW - Betoninstandsetzung KW - Instandsetzungssysteme KW - Polymer-Zement Beton (PCC) KW - Polymer-Zement Spritzbeton (SPCC) KW - Repair mortar KW - Concrete rehabilitation KW - Repair systems KW - Polymer cement concrete (PCC) KW - Sprayed polymer cement concrete (SPCC) PY - 2011 SN - 1864-7251 SN - 0947-4498 VL - 17 IS - 3/4 SP - 169 EP - 180 PB - Aedificatio Publ. CY - Freiburg AN - OPUS4-24479 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sarfraz, Adnan A1 - Schlegel, Moritz-Caspar A1 - Wright, J. A1 - Emmerling, Franziska T1 - Advanced gas hydrate studies at ambient conditions using suspended droplets N2 - We report the spontaneous formation of a clathrate hydrate in a suspended droplet at ambient conditions. A novel method for producing and stabilizing clathrates for analytical studies is described. KW - Clathrates KW - Thermography KW - Acoustic levitator KW - Dichloromethane PY - 2011 DO - https://doi.org/10.1039/c1cc13049h SN - 0022-4936 SN - 1359-7345 VL - 47 IS - 33 SP - 9369 EP - 9371 PB - Royal Society of Chemistry CY - Cambridge AN - OPUS4-24480 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kühl, Christiane A1 - Balke, Christian T1 - Neuerungen der Rechtsvorschriften zum Transport gefährdender Stoffe in Rohrfernleitungen N2 - Mit der Rohrfernleitungsverordnung u uA (RohrFLtgV) soll seitens des Gesetzgebers die Sicherheit des Transports von Stoffen, die im Falle eines Leitungsschadens Mensch und Umwelt beeinträchtigen können, gewährleistet werden. Nach der RohrFLtgV müssen Beschaffenheit und Betrieb von Rohrfernleitungen dem Stand der Technik entsprechen. Dieser gilt als erreicht, wenn die detaillierten Anforderungen an Design, Bau, Verlegung, Betrieb und Überwachung entsprechend der Technischen Regel für Rohrfernleitungen (TRFL) erfüllt sind. Seit 2008 ist die RohrFLtgV zweimal geändert worden. Diese Änderungen betreffen im Wesentlichen die bisherigen Regelungen zu den Sachverständigen sowie die Erweiterung des Anwendungsbereichs. Auch die TRFL von 2003 wurde aktualisiert und im Mai 2010 vom Bundesministerium für Umwelt, Naturschutz und Reaktorsicherheit (BMU) im Bundesanzeiger veröffentlicht. Dieser Beitrag gibt eine Übersicht über die Neuerungen in der Verordnung sowie die neuen technischen Anforderungen und Inhalte nach TRFL. PY - 2011 SN - 0179-3187 VL - 127 IS - 4 SP - 154 EP - 158 PB - Urban-Verl. CY - Hamburg AN - OPUS4-24481 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Balke, Christian A1 - Schendler, Thomas T1 - Möglichkeiten und Grenzen der Ereignisauswertung - aufgezeigt am Beispiel Human Factor T2 - VdS-Seminar - 12. Meinungs- und Erfahrungsaustausch für Sachverständige nach § 29a Abs. 1 BlmSchG, Immissionsschutz- und Störfallbeauftragte CY - Köln, Deutschland DA - 2011-07-13 KW - Ereignisauswertung KW - Menschlicher Faktor KW - Beinahe-Ereignisse KW - Störfälle KW - Unfälle PY - 2011 VL - 3652 SP - 1 EP - 9 AN - OPUS4-24482 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Joseph, Viginia A1 - Matschulat, Andrea A1 - Polte, Jörg A1 - Rolf, Simone A1 - Emmerling, Franziska A1 - Kneipp, Janina T1 - SERS enhancement of gold nanospheres of defined size N2 - Monodisperse, citrate-stabilized gold nanoparticles of sizes ranging from 15 to 40 nm were synthesized and characterized by small angle X-ray scattering and UV-vis experiments. Identical surface properties of nanoparticles of different sizes to avoid variation in the chemical surface-enhanced Raman scattering (SERS) enhancement, as well as selection of experimental conditions so that no aggregation took place, enabled the investigation of enhancement of individual nanospheres. Enhancement factors (EFs) for SERS were determined using the dye crystal violet (CV). EFs for individual gold nanospheres ranged from 102 to 103, in agreement with theoretical predictions. An increase of the EFs of individual spheres with size can be correlated to changes in the extinction spectra of nanoparticle solutions. This confirms that the increase in enhancement with increasing size results from an increase in electromagnetic enhancement. Beyond this dependence of EFs of isolated gold spheres on their size, EFs were shown to vary with analyte concentration as a result of analyte-induced aggregation. This has implications for the application of nanoparticle solutions as SERS substrates in quantitative analytical tasks. KW - Surface-enhanced Raman scattering KW - Electromagnetic enhancement factor KW - Crystal violet KW - Citrate reduction KW - Gold nanoparticles PY - 2011 DO - https://doi.org/10.1002/jrs.2939 SN - 0377-0486 SN - 1097-4555 VL - 42 IS - 9 SP - 1736 EP - 1742 PB - Wiley CY - Chichester AN - OPUS4-24483 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wetzk, V. A1 - Eisenkolb, Tino A1 - Mehdianpour, Milad T1 - Bewertung historischer Brückenlager - Das Kontaktproblem - Teil 1 N2 - Der Beitrag thematisiert das Kontaktproblem und damit den kritischen Punkt der historischen gusseisernen und stählernen Lagertechnik. Nach einem Rückblick auf die historische Entwicklung der Bemessung der Lagerwalzen und allgemeinen Ausführungen zur Kontaktproblematik wird anhand analytischer und numerischer Untersuchungen der Zusammenhang zwischen der Kontaktspannung nach Hertz und der Mises-Vergleichsspannung als Grundlage für ein realistisches Bewertungskonzept aufgezeigt. KW - Hertzsche Pressung KW - Kontaktspannung KW - Vergleichsspannung KW - Lager, historisch KW - Lagerwalze KW - Analyse KW - Theorie KW - Hertzian contact stress KW - Contact stress KW - Equivalent stress KW - Bearing, historical KW - Bearing roller KW - Analysis KW - Theory KW - Bestandssicherung und Erhaltung KW - Versuche KW - Verbindungs- und Befestigungsmittel KW - Werkstoffe KW - Stahlbrückenbau KW - Sonderkonstruktionen KW - Berechnungs- und Bemessungsverfahren KW - Conservation and maintenance KW - Experimental set-ups KW - Fasteners KW - Materials KW - Steel bridges KW - Special structures KW - Analysis and calculation PY - 2011 DO - https://doi.org/10.1002/stab.201101435 SN - 0038-9145 SN - 1437-1049 SN - 0932-6375 VL - 80 IS - 6 SP - 404 EP - 412 PB - Ernst CY - Berlin AN - OPUS4-24484 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schiel, D. A1 - Rienitz, O. A1 - Jährling, R. A1 - Güttler, B. A1 - Matschat, Ralf A1 - Scharf, Holger A1 - Birkhahn, Jürgen A1 - Labarraque, G. A1 - Fisicaro, P. A1 - Borchers, U. A1 - Schwesig, D. T1 - Metrological concept for comparable measurement results under the European water framework directive: demonstration of its applicability in elemental analysis N2 - Within the scope of a project of the 'European Association of National Metrology Institutes' (EURAMET), a European metrological dissemination System (network) providing traceable reference values assigned to matrix materials for validation purposes is described and put to the test. It enables testing laboratories (TL) to obtain comparable results for measurements under the 'EU Water Framework Directive 2000/60/EC' (WFD) and thus, to comply with a core requirement of this very directive. The dissemination system is characterized by the fact that it is available to all laboratories throughout Europe which intend to perform measurements in the context of the WFD and that it can ensure sustainable metrological traceability to the International System of Units (SI) as a reference point for the measurement results. This Dissemination system is set up in a hierarchical manner and links up the level of the national metrology institutes (NMI) with that of the TLs via an intermediate level of calibration laboratories (CL) by comparison measurements. The CLs are expert laboratories with respect to the measurement of the analytes considered here (within the project, the CLs are called potential calibration laboratories (PCL)) and are additionally involved in the organization of comparison measurements within the scope of regional quality assurance (QA) systems. Three comparison measurements have been performed to support the approach. A total of about 130 laboratories participated in this exercise with the focus on the measurement of the priority substances Pb, Cd, Hg, and Ni defined in the WFD. The elemental concentrations in the water samples roughly corresponded to one of the established environmental quality standards (EQS), the annual average concentration (AA-EQS), which is defined in the daughter Directive 2008/105/EC of the WFD. It turned out that a significant number of TLs still need to improve their measurement methods in order to be able to fulfill the Minimum requirements of the WFD, in particular, with regard to the elements Cd and Hg probably due to their low EQS values. Furthermore, it became obvious that the hierarchical Dissemination system suggested here actually corresponds to the measuring capabilities of the three participating Groups (NMIs, PCLs, and TLs). KW - Metrology KW - Metrological traceability KW - Comparability KW - Elemental analysis KW - Water framework directive PY - 2011 DO - https://doi.org/10.1007/s00769-011-0792-z SN - 0949-1775 SN - 1432-0517 VL - 16 IS - 10 SP - 489 EP - 498 PB - Springer CY - Berlin AN - OPUS4-24485 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hieronymus, Hartmut A1 - Fischer, J. A1 - Heinrich, Sebastian A1 - Liebner, Christian A1 - Lange, T. A1 - Klemm, E. T1 - Sicherheitstechnische Untersuchungen zum Betrieb von Mikroreaktoren im Explosionsbereich N2 - Es wird eine Methode zur sicherheitstechnischen Untersuchung von Mikroreaktoren und mikrostrukturierten Komponenten, die im Explosionsbereich betrieben werden sollen, vorgestellt. Mikrostrukturierte Reaktoren sind nicht inhärent sicher, wenngleich der Bereich der sicheren Betriebsbedingungen gegenüber konventionellen Reaktoren erweitert ist. Der Explosionsbereich kann durch die Mikrostrukturen eingeengt werden. Am Beispiel von Ethylen/Sauerstoff-Gemischen und Ethylen/N2O-Gemischen wird hinsichtlich der Ausbreitung von Detonationen durch Kapillarrohre gezeigt, dass die sogenannte λ/3-Regel angewandt werden kann. Darüber hinaus werden erste Ergebnisse der Untersuchung der Ausbreitung von Explosionen durch einen Mikroreaktor mit rechteckigem Strömungskanal vorgestellt. KW - Detonationszellbreite KW - Explosionsgrenzen KW - Mikroreaktoren KW - Sicherheitstechnik KW - Detonation cell width KW - Explosion limit KW - Microreactor KW - Saftey engineering PY - 2011 DO - https://doi.org/10.1002/cite.201100112 SN - 0009-286X SN - 1522-2640 VL - 83 IS - 10 SP - 1742 EP - 1747 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-24486 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Würsig, Andreas A1 - Jochems, Frank T1 - Neue Zulassungspraxis Tanks T2 - BAM-Gefahrguttage 2011 Veranstaltungsreihe ERFA Tanks, BK-Schüttgut-Container und MEMU, BAM CY - Berlin, Germany DA - 2011-10-20 PY - 2011 AN - OPUS4-24487 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Calero, P. A1 - Hecht, Mandy A1 - Martínez-Mánez, Ramon A1 - Sancenón, F. A1 - Soto, J. A1 - Vivancos, J.L. A1 - Rurack, Knut T1 - Silica nanoparticles functionalised with cation coordination sites and fluorophores for the differential sensing of anions in a quencher displacement assay (QDA) N2 - In conjunction with quenching metal ions, silica nanoparticles carrying terpyridine coordination sites and sulforhodamine B signalling units were employed for the differential fluorometric recognition of anions. KW - Hybridmaterial KW - Silica-Nanopartikel KW - Fluoreszenz KW - Anionen KW - Verdrängungsassay PY - 2011 DO - https://doi.org/10.1039/c1cc13039k SN - 0022-4936 SN - 0009-241x SN - 1359-7345 SN - 1364-548x VL - 47 IS - 38 SP - 10599 EP - 10601 PB - Royal Society of Chemistry CY - Cambridge AN - OPUS4-24489 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Avilov, Vjaceslav A1 - Bachmann, Marcel A1 - Gumenyuk, Andrey A1 - Lammers, Marco A1 - Rethmeier, Michael T1 - Inductive Electromagnetic Weld Pool Support System for High-Power Laser Beam Welding of Thick Aluminium Plates T2 - 4th International Conference on Magneto-Science CY - Shanghai, China DA - 2011-10-09 PY - 2011 AN - OPUS4-24490 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosemann, P. A1 - Bender, S. A1 - Heyn, Andreas A1 - Schmidt, J. T1 - Korrosion and Biokompatibilität beschichteter MgCa1,0 Magnesiumlegierungen N2 - Die Magnesiumlegierung Mg-Cal besitzt als potentielles bioabsorbierbares Implantatmaterial die Möglichkeit, vollständig vom menschlichen Körper absorbiert zu werden. Die mechanischen Kennwerte dieser Legierung liegen im Bereich des menschlichen Knochens und beide Legierungselemente (Mg, Ca) sind essentielle Spurenelemente im menschlichen Organismus. Der limitierende Faktor für den Einsatz ist die hohe Degradationsrate dieser Legierung. Um die Degradationsgeschwindigkeit zu verringern, wurden zwei Beschichtungssysteme auf Grundlage der Plasmachemischen Oxidation (PCO) und organischer Beschichtung erzeugt und untersucht. Das Korrosionsverhalten dieser Schichtsysteme wurde dabei mit dem Elektrochemischen Rauschen analysiert. Zusätzlich wurde der Einfluss von Wasserstoffentwicklung und eines ansteigenden pHWert auf die Zelltoxizität untersucht. Die Ergebnisse zeigen, dass eine Kombination von beiden Schichtsystemen zu einem viel versprechenden Degradationsverhalten führt. T2 - 14. Sommerkurs Werkstoffe und Fügen am Institut für Werkstoff- und Fügetechnik CY - Magdeburg, Germany DA - 23.09.2011 KW - Magnesium KW - Magnesium-Calcium KW - Implantat KW - Beschichtung KW - Plasmachemische Oxidation KW - Korrosion KW - Elektrochemisches Rauschen PY - 2011 SN - 978-3-940961-56-3 SP - 135 EP - 138 AN - OPUS4-24491 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, T. A1 - Heyn, Andreas A1 - Burkert, Annette A1 - Ebell, Gino T1 - Erfassung und Analyse der Startvorgänge lokaler Korrosion mittels kombinierter elektrochemischer und mikroskopischer Methoden N2 - Zur Untersuchung der Initiierungsvorgänge und dem Wachstumsverhalten lokaler Korrosionskeime auf nichtrostenden Stählen wurde eine neue elektrochemisch-mikroskopische Messmethode entwickelt. Bei dieser Messmethode wird durch Einsatz eines Echtfarben- Konfokalmikroskops mit Immersionsobjektiv das empfindliche elektrochemische Rauschmessverfahren um eine bildgebende Messkomponente erweitert. Ziel dieser Untersuchung war es, diskrete Rauschmesssignale visuell detektierbaren Korrosionserscheinungen auf der Stahloberfläche nahezu in Echtzeit zuzuordnen. Auf Grund der notwendigen Anforderungen an einen in situ Messaufbau wurde im Rahmen dieser Untersuchung ein neuartiges selbstklebendes Folienelektrodensystem, bestehend aus Gegen- und Bezugselektrode, entwickelt, das für die in situ Messung zum Einsatz kam. Die in situ Untersuchungen wurden an dem austenitischen Chrom-Nickel-Stahl 1.4301 durchgeführt. Als Ergebnis der Experimente konnten Stromtransienten im nA- bis μA-Bereich messtechnisch erfasst werden und mikroskopisch kleinen Korrosionskeimen, die sowohl stabil wie auch metastabil auf der Stahloberfläche auftraten, diskret und zeitnah zugeordnet werden. Weiterhin konnten mit Hilfe der Konfokaltechnik die Volumina und die Mantelflächen der einzelnen Lochdefekte ermittelt werden, sodass durch Auswertung und Kombination der elektrochemischen und mikroskopischen Messergebnisse erstmalig die Korrosionsstromdichte bestimmt werden konnte, die bei der Initiierung der lokalen Lochkeime aufgetreten ist. Damit konnte die Funktionalität und die hohe Empfindlichkeit des elektrochemisch-mikroskopischen Messverfahrens im Rahmen dieser Untersuchung erfolgreich verifiziert werden. T2 - 14. Sommerkurs Werkstoffe und Fügen am Institut für Werkstoff- und Fügetechnik CY - Magdeburg, Germany DA - 23.09.2011 KW - Lochkorrosion KW - Lochkeimbildung KW - Konfokalmikroskopie KW - In situ KW - Elektrochemie KW - Elektrochemisches Rauschen KW - Folienelektrode PY - 2011 SN - 978-3-940961-56-3 SP - 149 EP - 158 AN - OPUS4-24492 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmigalla, S. A1 - Heyn, Andreas T1 - Entwicklung einer Prüfmethode zur Untersuchung des Lochkorrosionsverhaltens von CMT-geschweißten Nickel-Basisplattierungen N2 - Höchstlegierte NiCrMo-Legierungen finden in weiten Bereichen der chemischen Industrie, der Offshoretechnik sowie in Rauchgasentschwefelungsanlagen Anwendung. Dabei werden an diese Werkstoffe höchste Anforderungen hinsichtlich der Korrosionsbeständigkeit gestellt. Neben der Verwendung von Vollmaterial gewinnt infolge gestiegener Rohstoffpreise die Applikation von auftraggeschweißten Plattierungen auf einem niedriglegierten Substratwerkstoff immer weiter an Bedeutung, wobei prinzipiell gegenüber den jeweiligen Walzwerkstoffen ein verschlechtertes Korrosionsverhalten der Plattierungen zu erwarten ist. Die Anwendung des CMT (Cold Metal Transferj-Prozesses bietet aufgrund eines geringen Wärmeeintrags gegenüber konventionellen Auftragschweißverfahren verfahrensspezifische Vorteile. Um eine unter Betriebsbedingungen ausreichende Korrosionsbeständigkeit zu gewährleisten, ist es erforderlich, ein Prüfverfahren zu entwickeln, welches den Einfluss der verschiedenen Verfahrensparametern auf das Lochkorrosionsverhalten exakt und reproduzierbar darstellen kann. Bisher bekannte Prüfmethoden, wie die Bestimmung kritischer Lochkorrosionstemperaturen durch Auslagerungsversuche in HCl-haltiger FeCf-Lösung oder die Aufnahme von Stromdichte-Potential-Kurven zur Bestimmung kritischer Lochkorrosionspotentiale, erweisen sich für die höchstlegierten Werkstoffe aus der Gruppe der NiCrMo-Legierungen als ungeeignet, da sich diese unter den gegebenen Bedingungen als lochkorrosionsbeständig erweisen. Somit kann der Einfluss der Schweißparameter während des Plattierprozesses auf das Lochkorrosionsverhalten mit den bislang bekannten Prüfverfahren nicht untersucht werden. T2 - 14. Sommerkurs Werkstoffe und Fügen am Institut für Werkstoff- und Fügetechnik CY - Magdeburg, Germany DA - 23.09.2011 KW - Korrosionsschutz KW - Plattierung KW - Nickelbasislegierung KW - CMT KW - Lochkorrosion KW - Korrosionsprüfung KW - Elektrochemisches Rauschen PY - 2011 SN - 978-3-940961-56-3 SP - 139 EP - 148 AN - OPUS4-24493 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Poltavtseva, M. A1 - Heyn, Andreas A1 - Boese, E. T1 - Mechanismen des Korrosionsschutzes plattierter Aluminiumwerkstoffe am Beispiel von Alclad 6025 N2 - Plattierte Aluminiumwerkstoffe sind qualitativ hochentwickelte Mehrschichtmaterialverbunde, die aus einer Kemlegierung und einer Plattierung bestehen. Das Kemmaterial erfüllt die Anforderungen an Festigkeit und Lebensdauer des Bauteils. Die Legierungen, die für Plattierungen verwendet werden, sorgen für den Korrosionsschutz unter meist atmosphärischen Bedingungen. Plattierte Aluminiumwerkstoffe finden vor allem Anwendung in der Luftfahrtkonstruktion oder wie Alclad 6025 im Bauwesen als Verkleidung von Fassaden und als Dacheindeckungen. In der Literatur wird der Korrosionsschutzmechanismus plattierter Aluminiumwerkstoffe allgemein als galvanischer Schutz beschrieben. Wenn eine Beschädigung der Plattierung bis zum Kern reicht, soll sich die elektronegativere Plattierung bevorzugt auflösen und damit die Kemlegierung schützen. Die Plattierungslegierung soll hinreichend korrosionsbeständig sein. Dabei kann eine leichte allgemeine Korrosion oder Lochkorrosion akzeptiert werden, allerdings mit einer geringen Tiefe, damit die Kernlegierung nicht korrodiert. Da jedoch keine detaillierten Angaben über den Schutzmechanismus in der Literatur gegeben werden, wurden am Beispiel von Alclad 6025 umfangreiche elektrochemische Untersuchungen sowie Auslagemngsversuche in verschiedenen Atmosphären bzw. Medien durchgeführt. Aus diesen Ergebnissen soll der Schutzmechanismus am Beispiel der Dachplattierung Alclad 6025 genauer beschrieben werden. T2 - 14. Sommerkurs Werkstoffe und Fügen am Institut für Werkstoff- und Fügetechnik CY - Magdeburg, Germany DA - 23.09.2011 KW - Plattierung KW - Aluminium KW - Alclad KW - Korrosionsmechanismus KW - Korrosionsschutz KW - Lochkorrosion KW - Korrosionsprüfung PY - 2011 SN - 978-3-940961-56-3 SP - 159 EP - 166 AN - OPUS4-24494 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kiefer, R. A1 - Boese, E. A1 - Heyn, Andreas A1 - Engelking, M. A1 - Hillert, R. T1 - Korrosion verchromter Kunstoffanbauteile unter verschärfter Streusalzbelastung mit CaCl2 N2 - Dekorativ verchromte Kunststoffanbauteile werden seit Anfang der 1970er Jahre in der Automobilindustrie eingesetzt, um einem Fahrzeug eine optisch höhere Wertigkeit zu geben. Diese mikroporig bzw. mikrorissig galvanisch abgeschiedenen Überzüge auf Kunststoffanbauteilen sind in einer festgelegten Reihenfolge übereinander angeordnet, um die Funktionen Dekorativität und Korrosionsbeständigkeit zu erfüllen. Unter dem Chromüberzug befindet sich u.a. ein Glanznickelüberzug, welcher durch Poren bzw. Risse bei Kontakt mit Streusalzsole gezielt korrodieren soll und somit den Chromüberzug kathodisch schützt. Der Zusatz von Kalziumchlorid in die Streusalzmischungen in Regionen mit extrem niedrigen Temperaturen (z. B. Winter in Moskau) stört diesen Mechanismus. Unter diesen Bedingungen wurden flächenhafte Schäden am Chromüberzug mikroporig verchromter Kunststoffanbauteile beobachtet. Bei Volkswagen erfolgte daraufhin die Umstellung aller verchromten Bauteile im Exterieur auf mikrorissig. Die Ursache für diese Schäden soll in der vorliegenden Arbeit geklärt werden. T2 - 14. Sommerkurs Werkstoffe und Fügen am Institut für Werkstoff- und Fügetechnik CY - Magdeburg, Germany DA - 23.09.2011 KW - Chrom-Nickel-Überzug KW - Streusalz KW - Calziumchlorid KW - Korrosionsschaden KW - Automobilbau KW - Korrosionsprüfung KW - Elektrochemie PY - 2011 SN - 978-3-940961-56-3 SP - 167 EP - 176 AN - OPUS4-24495 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Podgursky, V. A1 - Adoberg, E. A1 - Surzenkov, A. A1 - Kimmari, E. A1 - Viljus, M. A1 - Mikli, V. A1 - Hartelt, Manfred A1 - Wäsche, Rolf A1 - Síma, M. A1 - Kulu, P. T1 - Dependence of the friction coefficient on roughness parameters during early stage fretting of (Al,Ti)N coated surfaces N2 - Main focus was on the correlation of the coefficient of friction (COF) with the geometrical parameters of the surface during early stage of the running-in period. TiN, TiAlN and AlTiN coatings were prepared by using rotating cathode arc evaporation unit. The roughness of the WC-Co substrate Ra ranged from 0.05 to 0.2 µm and the coating thickness was 2.3 ± 0.2 µm. Part of the samples were subjected to the surface modification by the drag grinding finishing. Geometrical parameters of the surface were evaluated by means of atomic force microscopy (AFM) and fretting tests were conducted with 10 mm diameter alumina ball under 2 N load, 100 µm slip distance and the frequency of 10 Hz. It was found that the distribution of macroparticles strongly influences the geometrical parameters of the surface and the number of macroparticles increases with increasing Al content in the coating. In the case of the positive skewness Ssq of the coating surface, the kurtosis Sku provides a statistically significant effect on the COF, namely the COF depends inversely on the kurtosis Sku. The kurtosis value for TiN was the highest among as-deposited coatings, subsequently, the slowest increase rate in the COF was observed for the TiN coating. KW - PVD coatings KW - AFM KW - Surface topography KW - COF PY - 2011 DO - https://doi.org/10.1016/j.wear.2011.03.006 SN - 0043-1648 VL - 271 IS - 5-6 SP - 853 EP - 858 PB - Elsevier CY - Amsterdam AN - OPUS4-24497 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pirskawetz, Stephan A1 - Rieffel, Y. A1 - Ruedrich, J. A1 - Plagge, R. A1 - Weise, Frank A1 - Siegesmund, S. A1 - Ruisinger, U. T1 - An inter-disciplinary model project to develop an innovative winter covering system N2 - Eight monumental sculptural groups made of Carrara marble are situated on the Schlossbrücke in the centre of Berlin in the periphery of the Museum Island, a Unesco world cultural heritage site. T2 - 14es journées d'étude de la SFIIC - Jardin de pierres - Conservation of stone in parks, gardens and cemetries CY - Paris, France DA - 22.06.2011 KW - Marble KW - Cultural heritage KW - Schlossbrücke KW - Protective winter cover KW - Deterioration KW - Numerical simulation PY - 2011 SN - 2-905430-17-6 SP - 122 EP - 131 AN - OPUS4-24368 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Urs A1 - von Weschpfennig, D. A1 - Malaga, Katarina T1 - Anti-Graffiti-Systeme auf Mauerwerk im Bereich der Bundesfernstraßen N2 - Ingenieurbauten des Bundesfernstraßenbereichs sind aufgrund ihrer Exposition an vielen Stellen besonders betroffen von Graffiti. Graffitischmierer nehmen hierbei keine Rücksicht auf die Art der Substratmaterialien, und besonders poröse Untergründe bereiten Schwierigkeiten bei der Reinigung. Um Baustoffoberflächen besser zu schützen und von Graffiti leichter reinigen zu können, wurden in den vergangen Jahren spezielle Prophylaxesysteme (Anti-Graffiti-Systeme, AGS) entwickelten. Für die Beurteilung der Funktionalität und Verwendbarkeit dieser Anti-Graffiti-Systeme wurden von der Bundesanstalt für Straßenwesen (BASt) eine neue Technische Prüfvorschrift und Technische Lieferbedingungen (TP/TL AGS-Beton) erarbeitet. Die TP/TL AGS-Beton gilt hierbei nur für die Beurteilung von AGS auf Betonuntergründen. In einer Forschungsstudie wurde untersucht, inwieweit die vorhandene Prüfvorschrift für Betonsubstrate auch auf andere Untergründe, z. B. Naturstein oder Klinker, angewendet werden kann. Weiterhin wurde untersucht, welche Faktoren eine Rolle bei der Reinigung von mit AGS behandelten verschiedenen Substraten spielen. KW - Anti-Graffiti-System KW - Mauerwerk KW - Beton KW - Reinigungseigenschaft KW - Graffiti KW - Bundesfernstraßenbereich KW - Bauwerkserhaltung/Sanierung KW - Mauerwerksbau KW - Anti-graffiti system KW - Masonry KW - Concrete KW - Cleaning efficacy KW - Maintenance and Repair KW - Masonry construction KW - Federal Motorway System PY - 2011 DO - https://doi.org/10.1002/bate.201101479 SN - 0932-8351 SN - 1437-0999 SN - 0005-6820 SN - 0341-1052 SN - 0932-6359 VL - 88 IS - 7 SP - 443 EP - 450 PB - Ernst & Sohn CY - Berlin AN - OPUS4-24369 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Piechotta, Christian A1 - Schmidt, Sebastian A1 - Nehls, Irene T1 - A New Approach for the Characterization of Commercial Linear Alkylbenzene Sulfonate (LAS) T2 - 5. Conference über Ionenanalyse (CIA) CY - Berlin, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-24371 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Torge, Manfred A1 - Müller, W. T1 - Staubmessungen im Spalt zwischen Original und Schutzverglasung N2 - An jeweils einem Fenster der Dome zu Stendal, Havelberg und Halberstadt sowie im Zisterzienserkloster Marienstern in Panschwitz-Kuckau und der Nikolaikirche in Quedlinburg wurden Klimamessungen sowie Staub- und Materialuntersuchungen durch die Bundesanstalt für Materialforschung und -prüfung, Fachgruppe 4.2 durchgeführt. Ziel der Arbeiten war es, den allgemeinen Erkenntnisstand über die Wirksamkeit von Schutzverglasungen zu verbessern, die spezifische Situation für die Glasmalereien in den fünf Objekten zu beurteilen (siehe Faltblatt 6 dieser Reihe: „Kontrollen der Wirksamkeit von Schutzverglasungen"), im Bedarfsfall Maßnahmen zur Verbesserung zu empfehlen und gegebenenfalls weitere Untersuchungen vorzuschlagen. Bisher gibt es keine Erkenntnisse zum Einfluss von Stäuben auf die Korrosionsprozesse von Glasoberflächen. Daher sollte das Projekt neben der unmittelbaren Kontrolle der fünf Objekte auch Antworten zu dieser grundlegenden Frage geben. PY - 2011 UR - http://www.nike.bam.de/de/nike_medien/11-09_bam_7_staubmessungen_spalt_original_schutzverglasungen.pdf SP - 1 EP - 8 PB - Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-24372 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bremser, Wolfram T1 - Acitivities of ISO/REMCO T2 - 3rd Allrussian Conference with International Participation "CRM in measurement and technology" CY - Yekaterinburg, Russia DA - 2011-09-12 PY - 2011 AN - OPUS4-24373 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bremser, Wolfram T1 - Traceability of CRM: REMCO WG15 acitivities T2 - 3rd Allrussian Conference with International Participation "CRM in measurement and technology" CY - Yekaterinburg, Russia DA - 2011-09-12 PY - 2011 AN - OPUS4-24374 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bremser, Wolfram T1 - Alternative approaches to stability assessment of CRM T2 - 3rd Allrussian Conference with International Participation "CRM in measurement and technology" CY - Yekaterinburg, Russia DA - 2011-09-12 PY - 2011 AN - OPUS4-24375 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Torge, Manfred A1 - Müller, W. T1 - Kontrolle der Wirksamkeit von Schutzverglasungen N2 - Als wichtigste Konservierungsmaßnahme für mittelalterliche Glasmalereien gilt seit vielen Jahrzehnten die Schutzverglasung. Von den anfänglich unterschiedlichen Konstruktionen hat sich das von innen belüftete System bald durchgesetzt. Umfangreiche Klimamessungen an Schutzverglasungen in insgesamt 11 Kirchen, bei deren Auswertung und Beurteilung vor allem bautechnische Details, räumliche Lagen und Heizvorrichtungen in Betracht gezogen wurden, ergaben große Unterschiede in der klimatischen Situation der Glasmalereien. Obwohl aus den Ergebnissen Schlüsse hinsichtlich positiver und negativer Einflüsse vieler Faktoren ableitbar sind, bleiben manche Fragen weiter offen. Dazu gehört in erster Linie eine bildlich (mikroskopisch/elektronenmikroskopisch) belegte Aussage, inwieweit die Schutzverglasung über längere Zeiträume den Zustand der Glasmalerei tatsächlich zu konservieren vermag. Sicher ist, dass die bauphysikalischen Bedingungen, die Lage des Fensters (Himmelsrichtung) und seine Dimension großen Einfluss auf das Klima im Spalt zwischen Schutzverglasung und Original haben. Sowohl diese Erkenntnisse als auch der Mangel an systematischen Untersuchungen nach der Neuinstallation von Schutzverglasungen waren Anlass für ein Evaluierungsprojekt, bei dem die vor etwa 15 Jahren installierten Schutzverglasungen an Fenstern des Halberstädter Doms, des Havelberger Doms, des Stendaler Doms und der Nikolaikirche Quedlinburg hinsichtlich ihrer konservierenden Wirksamkeit überprüft wurden. Mit dem Hussitenfenster der Klosterkirche Marienstern in Panschwitz-Kuckau wurde ferner ein Objekt mit einer bereits vor 25 Jahren installierten Schutzverglasung hinzugenommen. An jeweils einem Fenster der fünf Objekte wurden Klimamessungen sowie Staub- und Materialuntersuchungen durch die Bundesanstalt für Materialforschung und -prüfung durchgeführt. Ziel der Arbeiten war, den allgemeinen Erkenntnisstand über die Wirksamkeit von Schutzverglasungen zu verbessern, die spezifische Situation für die Glasmalereien in den fünf Objekten zu beurteilen, im Bedarfsfall Maßnahmen zur Verbesserung zu empfehlen und gegebenenfalls weitere Untersuchungen vorzuschlagen. Bisher gibt es keine Erkenntnisse zum Einfluss von Stäuben auf die Korrosionsprozesse. Das Projekt sollte neben der unmittelbaren Kontrolle der fünf Objekte auch Antworten zu diesen grundlegenden Fragen geben. PY - 2011 UR - http://www.nike.bam.de/de/nike_medien/11-09_bam_6_kontrolle_wirksamkeit_schutzverglasungen.pdf SP - 1 EP - 8 PB - Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-24376 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai A1 - Wilrich, Cordula T1 - Acetylenflaschen und poröse Materialien T2 - 2. Erfahrungsaustausch Acetylen, BAM TTS CY - Berlin, Germany DA - 2011-09-20 PY - 2011 AN - OPUS4-24468 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ferrero, Fabio A1 - Kreißig, Michael A1 - Kluge, Martin A1 - Holtappels, Kai T1 - On the Ignition of Acetylene-Acetone Mixtures on Hot Walls T2 - ECCE 2011 CY - Berlin, Germany DA - 2011-09-25 PY - 2011 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. AN - OPUS4-24469 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meng, Birgit A1 - Herbst, Tristan A1 - Rübner, Katrin A1 - Hauer, B. T1 - Assessment-concept for the sustainable use of secondary aggregates in concrete T2 - International Conference (RILEM-Week) on Advances in Construction Materials through Science and Energineering CY - Hong Kong, China DA - 2011-09-05 PY - 2011 AN - OPUS4-24470 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Taffese, W.Z. A1 - Kumaran, G.S. A1 - Uzoegbo, H.C. A1 - Kühne, Hans-Carsten T1 - LightSHIP II - Inorganic Binder System for Innovative Panel Technology in East Africa T2 - Africa Re:Load/Discover new opportunities for innovation and business, öffentlicher Workshop CY - Weimar, Germany DA - 2011-08-29 PY - 2011 AN - OPUS4-24471 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Priebe, Nsesheye Susan T1 - Managing an EU funded project in light of the SPIN project T2 - DAAD Workshop Nairobi:German/Africa Seminar CY - Nairobi, Kenya DA - 2011-10-07 PY - 2011 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. AN - OPUS4-24473 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Acikalin, Hatice Aydan A1 - Schalau, Bernd T1 - Quantitative Risikoanalyse - Grundlagen und Vorgehensweise der BAM T2 - Fortbildungslehrgagn des LANUV "Gefahren- und Risikoanalyse" CY - Essen, Germany DA - 2011-05-04 PY - 2011 AN - OPUS4-24474 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Acikalin, Hatice Aydan A1 - Schalau, Bernd A1 - Drewitz, Yvonne T1 - Quantitiative Risk analysis in the Process Industries: Methodology of BAM and Case Studies T2 - 8th European Congress of Chemical Engineering CY - Berlin, Germany DA - 2011-09-25 PY - 2011 AN - OPUS4-24475 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tang, Z. A1 - Schempp, Philipp A1 - Seefeld, T. A1 - Schwenk, Christopher A1 - Vollertsen, F. T1 - Verbesserung der Schweißeignung von Aluminium durch Kornfeinung T2 - DVS Congress, Große Schweißtechnisch Tagung CY - Hamburg, Germany DA - 2011-09-27 PY - 2011 AN - OPUS4-24476 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unger, Wolfgang T1 - Aminated functional organic surfaces as viewed by XPS, X-ray absorption spectroscopy and ToF-SIMS T2 - 14th European Conference on Applications of Surface and Interface Analysis (ECASIA 11) CY - Cardiff, Wales DA - 2011-09-04 PY - 2011 AN - OPUS4-24477 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heyn, Andreas T1 - Korrosionsuntersuchungen und -prüfungen bei der Beschichtungsentwicklung T2 - Mikromeeting "Korrosionsschutz für Leichtmetalllegierungen in der Luftfahrt durch Atmosphärendruck-Beschichtungsverfahren" CY - Jena, Germany DA - 2011-10-06 PY - 2011 AN - OPUS4-24458 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heyn, Andreas T1 - Elektrochemisches Rauschen bei der Korrosion als Bestandteil von Prüf- und Untersuchungskonzepten T2 - 6. Workshop "Korrosionsdiagnostik und Korrosionsüberwachung mit Hilfe des elektrochemischen Rauschens", Otto-von-Guericke Universität CY - Magdeburg, Germany DA - 2011-09-15 PY - 2011 AN - OPUS4-24459 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan T1 - Bestimmung der ED-Röntgenspektrometer-Eigenschaften mit dem BAM-Testmaterial EDS-TM001 T2 - µ-RFA-Workshop, BAM CY - Berlin, Germany DA - 2011-09-22 PY - 2011 AN - OPUS4-24460 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beck, Uwe T1 - Plasmabeschichtungsverfahren - eine Übersicht T2 - OPTEC BB: Messen, Prüfen, Kalibrieren (MPK-2011): Beschichtung von metallischen Oberflächen CY - Potsdam, Germany DA - 2011-10-26 PY - 2011 AN - OPUS4-24461 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan A1 - Rackwitz, Vanessa A1 - Ostermann, Markus T1 - Nachweisgrenzen der µ-RFA mit REM/EDS für RoHS-Elemente T2 - µ-RFA-Workshop, BAM CY - Berlin, Germany DA - 2011-09-22 PY - 2011 AN - OPUS4-24462 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Altenkirch, J. A1 - Gibmeier, J. A1 - Beyer, Katrin A1 - Kromm, Arne A1 - Kannengießer, Thomas T1 - Welding problems - Investigations with neutrons of residual stress and of hydrogen diffusion in steels N2 - We report about investigations of typical material problems in steels. First, residual stresses in and around weld seams with low martensite transition temperature filler material were analyzed w/ and w/o additional transverse tensile load. The investigation was accompanied by x-ray diffraction measurements to track stress-induced phase transitions. Martensite formation during welding under external load yield strain gradients near the surface that improve the integrity of the weld. Further, the residual stress distribution close to laser-treated steel surfaces was analyzed. The method could be improved to reduce analysis artifacts. Finally, hydrogen diffusion in different steels was measured using neutron radiography and subsequent image analysis. Diffusion coefficients were derived by analyzing the time-dependent mass flux. In an outlook we describe the optimal ESS instrumentation from a metallurgist’s point of view. T2 - ESS Workshop "Science Vision for the European Spallation Source - German Perspectives" CY - Bad Reichenhall, Germany DA - 2011-10-10 PY - 2011 UR - http://www.fz-juelich.de/cae/servlet/contentblob/1058986/publicationFile/24649/Griesche_pdf.pdf UR - http://www.fz-juelich.de/sid_BD693DF17F42B3018726EE5C2558C56C/jcns/EN/Leistungen/ConferencesAndWorkshops/ESS/_node.html AN - OPUS4-24464 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bleul, Regina A1 - Thiermann, Raphael A1 - Bachran, D. A1 - Maskos, Michael T1 - Probing Polymersome-Protein and -Cell Interactions: Structural Characterization and In Vitro Studies T2 - Bio-Nano Responses Conference CY - Essen, Germany DA - 2011-09-11 PY - 2011 AN - OPUS4-24465 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Thoralf A1 - Heyn, Andreas A1 - Burkert, Annette A1 - Ebell, Gino T1 - Detection and analysis of pitting initiation process by combining electrochemical and microscopic methods T2 - Eurocorr 2011 CY - Stockholm, Sweden DA - 2011-09-04 PY - 2011 AN - OPUS4-24466 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosemann, P. A1 - Bender, S. A1 - Heyn, Andreas A1 - Schmidt, J. T1 - In-vitro corrosion and biocompatibility study of coated MgCa1.0 magnesium alloys T2 - Eurocorr 2011 CY - Stockholm, Sweden DA - 2011-09-04 PY - 2011 AN - OPUS4-24467 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Houllé, Matthieu A1 - Kalinka, Gerhard A1 - Amadou, Julien A1 - Qian, H. A1 - Shaffer, M.S.P. A1 - Greenhalgh, E. A1 - Wienrich, Malte T1 - CNT-MODIFIED FABRICS FOR THE MANUFACTURING OF MULTI-FUNCTIONAL LAYERED COMPOSITES T2 - CESEP'11 4th International Conference on Carbons for Energy Storage/Conversion and Environment Protection CY - Vichy, France DA - 2011-09-25 PY - 2011 AN - OPUS4-24450 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Acetylenflaschen im Feuer T2 - BAM-Kolloquium CY - Berlin, Germany DA - 2011-08-31 PY - 2011 AN - OPUS4-24451 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shirshova, Natasha A1 - Kalinka, Gerhard A1 - Bismarck, A. A1 - Carreyette, Shuijin A1 - Fontana, Quentin P. A1 - Greenhalgh, E. A1 - Kucernack, Anthony A1 - Schaffer, Milo A1 - Wienrich, Malte T1 - Modified epoxy resin as electrolytes for structural supercapacitors T2 - European Polymer Congress 2011 CY - Granada, Spain DA - 2011-06-26 PY - 2011 AN - OPUS4-24452 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kolkoori, Sanjeevareddy A1 - Rahman, Mehbub-Ur A1 - Boehm, Rainer A1 - Prager, Jens A1 - Chinta, P.K. T1 - Simulation of Ultrasonic Sound Fields in Anisotropic Materials Using 2-D Ray Tracing Method T2 - International Congress on Ultrasonics (ICU), University of Gdansk CY - Gdansk, Poland DA - 2011-09-05 PY - 2011 AN - OPUS4-24453 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wallstabe, Ronald A1 - Klinger, Christian A1 - Bettge, Dirk A1 - Zunkel, Astrid T1 - Failure analysis of medical implants: importance of design, (material) defects and operational loading T2 - Materials Days CY - Rostock, Germany DA - 2011-10-06 PY - 2011 AN - OPUS4-24454 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingbeil, Dietmar A1 - Baer, Wolfram T1 - Development of a Key Curve Method fo Ductile Cast Iron at Dynamic Loading T2 - 37th MPA-Seminar "Materials and Components Behaviour in Energy & Plant Technology" CY - Stuttgart, Germany DA - 2011-10-06 PY - 2011 AN - OPUS4-24455 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tölle, Florian T1 - Eigenspannungsreduzierung in Elektronen- und Laserstrahlschweißnäthen mittels nachlaufender Wärmefelder durch schnelle Strahldefokussierung und -ablenkung T2 - DVS Congress 2011 CY - Hamburg, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-24457 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lange, K. A1 - Stark, Wolfgang A1 - Bohmeyer, W. A1 - Teteris, Gundars A1 - McHugh, J. T1 - Ultrasound measuring system: Principle and application T2 - Thermosets Conference 2011 - From monomers to components CY - Berlin, Germany DA - 2011-09-21 PY - 2011 AN - OPUS4-24438 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübert, Thomas A1 - Wernecke, R. T1 - Effizienter Energieeinsatz durch intelligente Feuchtemessung T2 - Microsystems Summer School Berlin 2011 "Energieeffizienz durch Mikrosystemtechnik" CY - Berlin, Germany DA - 2011-09-19 PY - 2011 AN - OPUS4-24440 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Senoner, Mathias A1 - Unger, Wolfgang A1 - Kollmer, F. T1 - BAM-L200: A new type of reference material for the determination of lateral resolution and the calibration of length scale T2 - 18th International Conference on Secondary Ion Mass Spectrometry CY - Riva del Garda, Italy DA - 2011-09-18 PY - 2011 AN - OPUS4-24441 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Senoner, Mathias A1 - Unger, Wolfgang T1 - Comparison of methods for the determination of lateral resolution in imaging surface analysis T2 - 14th International Conference on Applications of Surface and Interface Analysis (ECASIA 11) CY - Cardiff, Wales DA - 2011-09-04 PY - 2011 AN - OPUS4-24443 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heyn, Andreas T1 - Vom Phänomen zur Methode - 3 Jahrzehnte Elektrochemisches Rauschen in Magdeburg T2 - 14. Sommerkurs "Werkstoffe und Fügen" CY - Magdeburg, Germany DA - 2011-09-23 PY - 2011 AN - OPUS4-24444 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dietrich, Paul A1 - Gross, Thomas A1 - Horlacher, T. A1 - Girard-Lauriault, Pierre-Luc A1 - Lippitz, Andreas A1 - Min, Hyegeun A1 - Wirth, Thomas A1 - Castelli, R. A1 - Seeberger, P.H. A1 - Unger, Wolfgang T1 - Surface analytical investigations (XPS, NEXAFS and ToF-SIMS) of carbohydrate-functionalized surfaces T2 - SIMS XVIII, 18th International Conference on Secondary Ion Mass Spectrometry CY - Trento, Italy DA - 2011-09-18 PY - 2011 AN - OPUS4-24445 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heinze, Christoph A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - Influences on the result quality of numercial calculation of welding-induced distortion T2 - 3rd International Conference on Distortion Engineering, IDE CY - Bremen, Germany DA - 2011-09-16 PY - 2011 AN - OPUS4-24446 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiegner, Katharina A1 - Wilke, Olaf A1 - Horn, Wolfgang A1 - Kalus, Sabine A1 - Jann, Oliver T1 - Method validation study for emissions of volatile organic compounds (VOC) from construction products using emission test chambers T2 - EURACHEM: 7th Workshop; Proficiency testing in analytical chemistry, microbiology and laboratory medicine; Current Practice and Future Directions CY - Istanbul, Turkey DA - 2011-10-02 PY - 2011 AN - OPUS4-24447 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramanujam, Maalolan A1 - Wachtendorf, Volker A1 - Mix, Renate A1 - Schönhals, Andreas A1 - Friedrich, Jörg F. T1 - Effect of Artificial UV Weathering with Varied Humidity on Dielectric and Surface Properties of Polymers T2 - European Weathering Symposium 2011 (EWS) CY - Lisbon, Portugal DA - 2011-09-21 PY - 2011 AN - OPUS4-24428 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meyer-Plath, Asmus A1 - Hanelt, Sven A1 - Zenkel, C. T1 - Charakterisierung funktionalisierter CNT T2 - Inno.CNT Workshop "Funktionalisierte CNT" CY - Erlangen, Germany DA - 2011-09-20 PY - 2011 AN - OPUS4-24429 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gollwitzer, Christian T1 - On POD Estimations with Radiographic Simulator aRTist T2 - International Symposium on Digital Industrial Radiology and Computed Tomography CY - Berlin, Germany DA - 2011-06-20 PY - 2011 AN - OPUS4-24430 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schälike, Stefan A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter A1 - Chun, Hyunjoo A1 - Vela-Wallenschus, Iris A1 - Schönbucher, A. T1 - Surface emissive power of organic peroxide and hydrocarbon pool fires - experimentel and CFD simulation T2 - 8th European Congress of Chemical Engineering CY - Berlin, Germany DA - 2011-09-25 PY - 2011 N1 - Geburtsname von Vela-Wallenschus, Iris: Vela, I. - Birth name of Vela-Wallenschus, Iris: Vela, I. AN - OPUS4-24431 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maierhofer, Christiane T1 - Entwicklung von Normen und Standards für aktive Thermografie mit Blitzlichtanregung T2 - Workshop Blitzerthermographie der DGZfP CY - Berlin, Germany DA - 2011-06-27 PY - 2011 AN - OPUS4-24433 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maierhofer, Christiane T1 - Untersuchung von Schädigungsprzessen an Bauteiloberflächen und -grenzflächen mit Hilfe optischer und thermografischer zerstörungsfreier Prüfverfahren, Ergebnisse eines Projektes der Forschungsinitiative "Zukunft Bau" T2 - Thermografie am Bau, Seminar der DGZfP CY - Berlin, Germany DA - 2011-06-28 PY - 2011 AN - OPUS4-24434 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maierhofer, Christiane T1 - Prinzip der aktiven Termografie im Bauwesen und Anwendungen in der Denkmalpflege T2 - Thermografie am Bau, Seminar der DGZfP CY - Berlin, Germany DA - 2011-06-28 PY - 2011 AN - OPUS4-24435 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lange, Th. A1 - Heinrich, Sebastian A1 - Liebner, Christian A1 - Klemm, E. A1 - Hieronymus, Hartmut T1 - Partial oxidation of o-xylene to phtalic anhydride inside of the explosion regime using a micro structured reactor T2 - 8th European Congress of Chemical Engineering CY - Berlin, Germany DA - 2011-09-25 PY - 2011 AN - OPUS4-24436 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - McHugh, J. A1 - Stark, Wolfgang A1 - Grasnick, G. A1 - Sowada, M. A1 - Bohmeyer, W. T1 - Ultrasound technique for the characterisation of prepreg systems demonstrated using the vacuum bagging process T2 - Thermosets Conference 2011 - From monomers to components CY - Berlin, Germany DA - 2011-09-21 PY - 2011 AN - OPUS4-24437 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lischka, Susanne A1 - Nehls, Irene A1 - Piechotta, Christian T1 - Application of a twofold C-labeled calibration standard for the analysis of arsenobetaine using HPLC-ESI-MS/MS T2 - CIA CY - Berlin, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-24418 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lischka, Susanne A1 - Körte, F. A1 - Piechotta, Christian T1 - Arsenobetainbestimmung in Fisch mittels LC-ESI-MS/MS T2 - CIA CY - Berlin, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-24419 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von der Ehe, Kerstin A1 - Robertson, Daniela A1 - Wolff, Dietmar A1 - Böhning, Martin T1 - Structural differences of UHMWPE induced by high dose gamma irradiation T2 - 5th UHMWPE International Meeting CY - Philadelphia, PA, USA DA - 2011-09-22 PY - 2011 AN - OPUS4-24420 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin A1 - Goering, Harald A1 - von der Ehe, Kerstin A1 - Robertson, Daniela A1 - Wolff, Dietmar T1 - Characterization of structural changes in irradiated UHMWPE T2 - 11. Schwarzheider Kunststoffkolloquium CY - Schwarzheide, Germany DA - 2011-09-21 PY - 2011 AN - OPUS4-24423 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton T1 - Plant-specific safety review (RSK-SÜ) of German nuclear power plants in the light of the events in Fukushima-1 (Japan) T2 - IRRS follow-up Mission Germany 2011 CY - Bonn, Germany DA - 2011-09-05 PY - 2011 AN - OPUS4-24425 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Zündmechanismen mechanisch erzeugter Funken mit Bezug zur EN 13463-1 T2 - 5. Essener Explosionsschutztage (Veranstaltungs-Nr. E-H050-09-328-1) CY - Essen, Germany DA - 2011-09-28 PY - 2011 AN - OPUS4-24426 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habib, Abdel Karim A1 - Schalau, Bernd A1 - Schmidt, Dirk A1 - Rauchegger, Christian T1 - Calculation of the gas dispersion out of an evaporating pool T2 - 8th European congress of chemical engineering CY - Berlin, Germany DA - 2011-09-25 PY - 2011 AN - OPUS4-24427 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit T1 - Comparison of the material properties of polyethylene grades with the test performance behaviour of packgings for the transport of dangerous goods in dependence on the pre-storage time with 55 % nitirc acid T2 - Eurocorr 2011 CY - Stockholm, Sweden DA - 2011-09-04 PY - 2011 AN - OPUS4-24408 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulz, Wencke A1 - Nofz, Marianne A1 - Kranzmann, Axel A1 - Dörfel, Ilona T1 - Alumina Coatings for Protection of X20CrMoV12-1 T2 - Eurocorr 2011 CY - Stockholm, Sweden DA - 2011-09-04 PY - 2011 AN - OPUS4-24410 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulz, Wencke A1 - Dörfel, Ilona A1 - Saliwan Neumann, Romeo A1 - Nofz, Marianne A1 - Kranzmann, Axel T1 - Alumina Coatings under Oxyfuel Condition T2 - The 4th WMRIF (World Materials Research Institutes Forum) CY - Shenyang, China DA - 2011-05-22 PY - 2011 AN - OPUS4-24411 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulz, Wencke A1 - Saliwan Neumann, Romeo A1 - Nofz, Marianne A1 - Kranzmann, Axel T1 - Preparation of alumina layers on commercial power plant steels T2 - 2nd Oxyfuel Combustion Conference CY - Yeppoon, Australia DA - 2011-09-12 PY - 2011 AN - OPUS4-24412 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dörfel, Ilona A1 - Rooch, Heidemarie A1 - Österle, Werner A1 - Kranzmann, Axel T1 - V-Cr containing precipitates in the steel T92 before and after tests under oxyfuel steam power plant conditions T2 - Microscopy Conference 2011 CY - Kiel, Germany DA - 2011-08-28 PY - 2011 AN - OPUS4-24413 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bethke, John T1 - Stand der Normung (ISO/DIS 16495) / Revision der BAM-GGR 004 / Entwicklung eines "Kochbuches" (Leitfaden für die Prüfung von Gefahrgutverpackungen) T2 - Sitzung der BAM AK Prüfstellen CY - Berlin, Germany DA - 2011-09-23 PY - 2011 AN - OPUS4-24414 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bethke, John T1 - BAM-GGR 012 - Nachweis der ausreichenden chemischen Verträglichkeit von Verpackungen zur Beförderung gefährlicher Güter aus Polyethylen und aus koextrudiertem Kunststoff gegenüber flüssigen Stoffen T2 - Sitzung der BAM AK Prüfstellen CY - Berlin, Germany DA - 2011-09-23 PY - 2011 AN - OPUS4-24415 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wienecke, Bernd-Uwe T1 - BAM-GGR 013; Besondere Verfahren der Bauartprüfung und -zulassung von wiederaufgearbeiteten Fässern aus Stahl mit abnehmbarem Deckel (1A2) T2 - AK Prüfstellen CY - Berlin, Germany DA - 2011-09-23 PY - 2011 AN - OPUS4-24416 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Kömmling, Anja T1 - UV-LEDs - a new tool to determine the spectral response T2 - 5th European Weathering Symposium CY - Lisbon, Portugal DA - 2011-09-21 PY - 2011 AN - OPUS4-24417 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eiben, Mario T1 - Untersuchungen zu einem alternativen FNCT-Verfahren für den Nachweis der chemischen Verträglichkeit von Gefahrgutverpackungen aus Polyethylen T2 - Merk KGaA CY - Darmstadt, Germany DA - 2011-10-27 PY - 2011 AN - OPUS4-24678 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stoppel, Markus A1 - Taffe, Alexander A1 - Wiggenhauser, Herbert A1 - Kurz, J.H. A1 - Boller, C. T1 - Automated multi-sensor systems in civil engineering for condition assessment of concrete structures T2 - Concrete Solutions 2011, 4th International Conference on Concrete Repair CY - Dresden, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-24680 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trappe, Volker T1 - Betriebsfestigkeit und Zustandsüberwachung von Rotorblättern - Verifikation über Stellvertreterversuche T2 - Vortrag auf Tagung "Spree-WIND 2011" CY - Schönefeld, Germany DA - 2011-10-25 PY - 2011 AN - OPUS4-24681 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ortwein, Hans-Peter A1 - Bohse, Jürgen A1 - Trappe, Volker T1 - Untersuchung der Mikrorissbildung in Faserkunststoffverbunden mittels Röntgenrefraktions- und Schallemissionsmessung T2 - 18. Kolloquium Schallemission der DGZfP CY - Wetzlar, Germany DA - 2011-10-27 PY - 2011 AN - OPUS4-24682 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Altenkirch, J. A1 - Gibmeier, J. A1 - Kostov, V. A1 - Kromm, Arne A1 - Kannengießer, Thomas A1 - Doyle, S. A1 - Wanner, A. T1 - Time- and temperature-resolved synchrotron X-ray diffraction: observation of phase transformation and strain evolution in novel low temperature transformation weld filler materials N2 - Solid-state phase transformations and the evolution of thermal and elastic strains in novel low temperature transformation (LTT) weld filler materials in the near surface region are monitored in real time by means of an innovative experimental set-up at the PDIFF (powder diffraction) beamline at the synchrotron light source ANKA (Angströmquelle Karlsruhe) at the KIT (Karlsruhe Institute for Technology). The key components of the diffraction set-up are two fast microstrip line detectors, which enables the strain evolution to be followed as a function of time and temperature for a 0.5?s counting time. During controlled heating and cooling cycles, as well as during near welding cycles, the martensite–austenite–martensite phase transitions are analysed. The transformation kinetics are monitored during resistance heating of small chips of the pure LTT alloys and during gas tungsten arc welding of simplified LTT welds using a specially designed welding rig for in-situ studies on the diffraction instruments. Under the mechanically unconstrained condition allowing free thermal expansion and shrinkage, the LTT alloys are found to exhibit decreasing transformation temperatures Ac and MS and increasing phase fraction of retained austenite for increasing Ni content. The strain evolution during welding reveals increased compressive stresses upon welding, which is attributed to the martensite formation upon cooling, which counteracts the thermal contraction strains. Comparison of the transformation temperatures reveals higher values than in the pure LTT alloys, but no variation between the different alloys. On the one hand, this is attributed to preferred grain orientation affecting the diffraction measurements and the determination of the transformation temperatures. On the other hand, it is possible that with the different chemical compositions of the LTT alloys and the mechanical constraints during welding, the evolution of the residual strain and stress may vary and result in counteracting affects with respect to lowered martensite start temperatures. KW - In-situ synchrotron X-ray diffraction KW - Low temperature transformation KW - Welding PY - 2011 DO - https://doi.org/10.1177/0309324711413190 SN - 0309-3247 SN - 2041-3130 VL - 46 IS - 7 SP - 563 EP - 579 PB - Sage CY - London AN - OPUS4-24683 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Heinze, Christoph A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - Effect of heat source configuration on the result quality of numerical calculation of welding-induced distortion N2 - The results of numerical welding simulations strongly depend on its temperature field. In the present paper, the temperature field of a pulsed gas metal arc weld of structural steel S355J2+N (ASTM A572 Gr. 50) with a thickness of 5 mm is experimentally and numerically investigated. In the case of temperature field validation, volumetric Gauss and double-ellipsoid Goldak heat sources are applied. Additionally, different heat source configurations, including adaptations of thermal conductivity, are analyzed regarding their influence on the calculation of welding-induced distortion. The investigations clarify the influence of heat source configurations on the calculated results, thus, contribute to an improved prediction of welding-induced distortion. KW - Welding simulation KW - Heat source calibration KW - Gas metal arc welding KW - Sensitivity analysis KW - Distortion KW - Schweißsimulation KW - Verzug KW - Wärmequellenkonfiguration KW - Sysweld KW - Heat source configuration PY - 2011 DO - https://doi.org/10.1016/j.simpat.2011.09.004 SN - 1569-190X VL - 20 IS - 1 SP - 112 EP - 123 PB - Elsevier CY - Amsterdam [u.a.] AN - OPUS4-24684 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bettge, Dirk A1 - Klinger, Christian T1 - Schäden durch nichtmetallische Einschlüsse am Beispiel ICE 3 - Bedeutung und Lokalisierung einzelner nichtmetallischer Einschlüsse in großen Bauteilen N2 - Nichtmetallische Einschlüsse (NME) befinden sich in praktisch allen metallischen Bauteilen. Sie können auch unterhalb der Bauteiloberfläche als Starter von Schwingrissen fungieren. Besonders kritisch sind NME in oberflächennahen Bereichen in Bauteilen die großen Lastspielzahlen ausgesetzt sind. T2 - 37. VDI-Jahrestagung - Schadensanalyse - Produktverbesserung durch Schadensanalyse CY - Würzburg, Germany DA - 19.11.2011 KW - Schadensanalyse PY - 2011 SN - 978-3-18-092150-1 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte VL - 2150 SP - 159 EP - 173 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-24685 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. T1 - Interpretations of temperature measurements in organic peroxide pool fires N2 - Most of the measurements of temperatures in large pool fires are indirect and present a number of complexities due to the interactions of convection, radiation and soot blockage. In the present work these influences for two organic peroxide [tert-butyl peroxybenzoate (TBPB) and tert-butyl peroxy-2-ethylhexanoate (TBPEH)] pool fires are analysed. Thermocouple measured temperature in the clear flame zone i.e. combustion zone are found to be 250-400 K lower than from the thermographic measurements. The convective and radiative heat flux contributions from the fire on temperature measurements are discussed. CFD (Computational Fluid Dynamics) simulations have been performed for large pool fires and the predicted time averaged flame temperatures were found to be in qualitative agreement with measurements due to the stoichiometric combustion model used in the present simulations. T2 - 5th European combustion meeting 2011 CY - Cardiff, UK DA - 28.06.2011 KW - Pool fire KW - Organic peroxides KW - TBPB KW - TBPEH KW - CFD KW - Temperature measurement PY - 2011 UR - http://www.uni-due.de/tchem/as/skripte/paper_mishra_et_al_cardiff_2011.pdf SP - 1 EP - 5 AN - OPUS4-24686 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schälike, Stefan A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. T1 - CFD simulation to predict the thermal radiation of large LNG pool fires N2 - Flame temperature (T), surface emissive power (SEP) of Liquefied Natural Gas (LNG) pool fires (d = 1 m, 6.1 m, 30 m) are investigated by CFD (Computational Fluid Dynamics) simulation and compared with experimental results. Time averaged flame temperatures of T = 1320 K, T = 1298 K and T = 1281 K are obtained. Surface emissive power (SEP) of 55 kW=m2, 130 kW=m2 and 230 kW=m2 are predicted. T2 - 5th European combustion meeting 2011 CY - Cardiff, UK DA - 28.06.2011 KW - Pool fire KW - LNG KW - CFD KW - Thermal radiation KW - Surface emissive power PY - 2011 SP - 1 EP - 6 AN - OPUS4-24687 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wan, Wei A1 - Biyikal, Mustafa A1 - Rurack, Knut A1 - Wagner, Ricarda A1 - Sellergren, B. T1 - Molecularly imprinted polymers as sensory materials for the selective detection of carboxylates via fluorescence enhancement T2 - 4th Graduate Student Symposium on Molecular Imprinting CY - London, England DA - 2011-09-28 PY - 2011 AN - OPUS4-24698 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wagner, Ricarda A1 - Wan, Wei A1 - Biyikal, Mustafa A1 - Rurack, Knut A1 - Sellergren, B. T1 - Targeting biological and environmental analytes using imprinted chromogenic or fluorgenic receptors T2 - 2. Junges Chemie Symposium Ruhr CY - Essen, Germany DA - 2011-09-22 PY - 2011 AN - OPUS4-24699 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ferrero, Fabio A1 - Kluge, Martin A1 - Schröder, Volkmar T1 - Numerical analysis of the effect of the electrode distance during the determination of the flammability limits of gases N2 - COMSOL Multiphysics® was used as a tool for the better understanding of the evolution of flow patterns during the induced ignition of gases. A simplified model was developed for the scope, by coupling the weakly compressible Navier Stokes module and the convection and conduction module. The current paper presents the results of the performed simulations. T2 - COMSOL Conference 2011 CY - Ludwigsburg, Germany DA - 26.10.2011 KW - Spark ignition KW - Gas flow KW - Temperature PY - 2011 SN - 978-0-9839688-0-1 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. SP - 1 EP - 7 CY - Stuttgart AN - OPUS4-24700 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brand, U. A1 - Beckert, E. A1 - Beutler, A. A1 - Dai, G. A1 - Stelzer, C. A1 - Hertwig, Andreas A1 - Klapetek, P. A1 - Koglin, J. A1 - Thelen, R. A1 - Tutsch, R. T1 - Comparison of optical and tactile layer thickness measurements of polymers and metals on silicon or SiO2 N2 - The thickness measurement of transparent layers with optical techniques is very problematic. The observed deviations can easily reach 100% of the layer thickness to be measured. In order to analyse these deviations, tactile reference measurements have been developed. The proposed method is based on contact mode measurements with low contact pressure. With stylus instruments, this can be realized either by using the recommended tip radius of 2 µm and very small probing forces in the micronewton range (and low scanning speeds of 50 µm s-1) or by using the recommended probing force of 750 µN, but a large probing tip radius. Three metal layers on silicon or silicon dioxide and two polymer resist materials on a thin chromium adhesive layer on silicon are used as artefacts. The comparison of the optical measurements with the tactile reference values disclosed deviations of the optical measurements of up to 195% of the layer thickness. Layer thicknesses were between 200 nm and 4 µm. This paper analyses the deviations of two white light interference microscopes, one phase shift interference microscope, one confocal microscope, one autofocus sensor, a chromatic sensor, an interferometric film thickness sensor and one spectroscopic ellipsometer. Simple and well-known expressions for the description of the observed deviations are presented and discussed. The order of magnitude of the observed deviations can be described well by these correction formulas but further investigations are necessary in order to better understand the systematic deviations of optical surface measuring instruments on non-cooperating surfaces. KW - Layer thickness KW - Stylus instrument KW - Deformation KW - Polymer KW - Silicon KW - Silicon dioxide PY - 2011 DO - https://doi.org/10.1088/0957-0233/22/9/094021 SN - 0957-0233 SN - 1361-6501 VL - 22 IS - 094021 SP - 094021-1 - 094021-14 PB - IOP Publ. Ltd. CY - Bristol AN - OPUS4-24701 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scholz, Christian A1 - Woydt, Mathias T1 - Highly stressable and low friction slip-rolling contacts through thin film coatings, uncoated, alternative steels or lubricants N2 - OEMs perceive diamond-like carbon (DLC) coatings as part of a strategy for low frictional tribosystems. Especially the automotive industry anticipates a benefit in applying such coatings in association with the lightweight construction of mechanical parts, for instance in gears and engines. In previous investigations it was shown, that DLC, amorphous carbon (a-C) and tetragonal amorphous carbon (ta-C) coatings can be slip-rolling resistant at least up to ten million load cycles at Hertzian contact pressures P0max of 2.9 GPa lubricated by engine oil at 120°C, Further improvements in load carrying capacity up to P0mean of 2.62 GPa (FN= 5,000 N) were achieved with alternative, available Steel metallurgies as Substrates for thin film coatings. Additional factors, such as influences of the lubrication on the surface chemistry (additives and base oils), wear and friction behavior were investigated. T2 - International tribology conference 2011 CY - Hiroshima, Japan DA - 30.10.2011 KW - Slip-rolling KW - Additives KW - DLC KW - ZrCN KW - High toughness steel KW - High pressure PY - 2011 IS - B4-08 SP - 1 EP - 1 AN - OPUS4-24702 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mull, Birte A1 - Wiegner, Katharina A1 - Horn, Wolfgang T1 - Development of a Screening Method for SVOC in the Micro-Chamber Air and Indoors T2 - Emissions and odours from Materials 2011 CY - Brussels, Belgium DA - 2011-11-09 PY - 2011 AN - OPUS4-24704 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kranzmann, Axel A1 - Neddemeyer, Torsten A1 - Ruhl, Aki Sebastian A1 - Hünert, Daniela A1 - Bettge, Dirk A1 - Oder, Gabriele A1 - Saliwan Neumann, Romeo T1 - The challenge in understanding the corrosion mechanisms under oxyfuel combustion conditions N2 - Basic research on the corrosive effect of flue gases has been performed at the BAM Federal Institute for Materials Research and Testing (Germany). Conditions at both high and low temperatures were simulated in specially designed experiments. Carburization occured in flue gases with high CO2 content and temperatures higher than 500 °C. In SO2 containing flue gases sulphur was detected in the oxide scale. At lower temperatures no corrosion was observed when gases with low humidity were investigated. Humidity higher than 1500 ppm was corrosive and all steels with Cr contents lower than 12% revealed corroded surfaces. At low temperatures below 10 °C a mixture of sulphuric and nitric acid condensed on metal surfaces. Acid condensation caused severe corrosion. Humidity, CO2, O2, and SO2 contents are the important factors determining corrosion. Below 300 °C acid condensation is the primary reason for corrosion. Low humidity and low temperatures are conditions which can be expected in the CO2 separation and treatment process. This work includes major conditions of the flue gas and CO2 stream in CCS plants and CCS technology. KW - Coal KW - Oxyfuel power plant KW - Corrosion KW - Carburization KW - Sulphur KW - Sulphuric acid PY - 2011 DO - https://doi.org/10.1016/j.ijggc.2011.05.029 SN - 1750-5836 VL - 5 IS - Supplement 1 SP - S168 EP - S178 PB - Elsevier CY - New York, NY [u.a.] AN - OPUS4-24705 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ferrero, Fabio A1 - Kluge, Martin A1 - Spoormaker, T. T1 - Der Stoff, aus dem die Zukunft ist N2 - Beim begehrten Kunststoff Teflon führt kein Weg an einem komplexen Herstellungsprozess vorbei, der aufgrund der besonderen Eigenschaften des Ausgangsstoffes spezieller sicherheitstechnischer Anforderungen bedarf. Comsol Multiphysics unterstützte Wissenschaftler in der Auslegung der Produktionsanlagen bei der Identifizierung von Gefahrenquellen. KW - Tetrafluorethylen KW - Selbstentzündung KW - Numerisches Modell PY - 2011 SN - 1866-5004 SN - 1436-3348 SN - 0939-5504 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. VL - 6 SP - 64 EP - 66 PB - Göller CY - Baden-Baden AN - OPUS4-24706 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter T1 - An efficient and clean fuel for high temperature process industries N2 - The use of energetic materials as a main fuel in high temperature process industries are not known to the scientific community as such. This paper highlights some of the features and advantages of using organic peroxides especially di-tert-butyl peroxide (DTBP) in high temperature process industries. The feasibility of using DTBP as a main or supporting fuel in process industries have also been justified with the help of Computational Fluid Dynamics (CFD) simulations. For peroxides requirement of less fuel and air for the same amount of heat flux has been shown. The resulted emission from the combustion of DTBP is also discussed. T2 - 11th Conference on Energy for a Clean Environment CY - Lisbon, Portugal DA - 2011-07-05 KW - Energetic materials KW - Process industries KW - Organic peroxide KW - Di-tert-butylperoxide (DTBP) KW - CFD simulation KW - Emission PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-247071 SP - 1 EP - 10 AN - OPUS4-24707 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trela, Christiane T1 - Untersuchung zur Positioniergenauigkeit von automatisierten Radarmessungen T2 - Radar-Rundtischgespräch CY - Freiberg, Germany DA - 2011-09-06 PY - 2011 AN - OPUS4-24690 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lohrer, Christian T1 - Konformitätsbewertungsverfahren und Normung pyrotechnischer Gegenstände T2 - PYRO WORLD - Europäische Fach- und Consumer-Messe für Pyrotechnik CY - Berlin, Germany DA - 2011-11-10 PY - 2011 AN - OPUS4-24691 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stoppel, Markus A1 - Kurz, J.H. A1 - Taffe, Alexander A1 - Boller, C. ED - Chang, F.-K. T1 - Proactive condition assessment in civil engineering using automated multi-sensor systems N2 - Infrastructure is subject to continuous ageing. This has given life cycle management of infrastructure an increasing role. Reliable inspection and monitoring tools are therefore an increasing demand. A combination of different non-destructive test methods is often necessary to receive reliable results for material characterization, flaw detection and the determination of component specific geometry parameters. Regarding concrete structures thickness measurements are combined with flaw detection and additional information about reinforcement and tendon ducts is required. Therefore, a multi-sensor measurement approach is necessary with a high degree of automation. Otherwise a time consuming succession of manual measurements has to be performed which would prevent practical applications. A modular control and data acquisition approach is described and the application of two different automated measurement devices is shown. The BetoScan system consists of a self-navigating mobile robot. The system is especially designed for the investigation of reinforced concrete floors exposed to de-icing salts. The data acquisition of the OSSCAR system a multi-sensor scanner is similar to the robot approach. These different applications are based on a similar kernel allowing the modular use of different contact and noncontact sensors. The described general concept of multi-sensor data acquisition and data analysis presented here is not limited to the field of civil engineering applications. T2 - 8th International workshop on structural health monitoring 2011 CY - Stanford, CA, USA DA - 13.09.2011 KW - Multi sensor KW - Data acquisition KW - Assessment of concrete structures KW - Scanner KW - NDT PY - 2011 SN - 978-1-60595-053-2 VL - 2 SP - 2359 EP - 2366 PB - DEStech Publications, Inc. AN - OPUS4-24692 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brauser, Stephan A1 - Kromm, Arne A1 - Kannengießer, Thomas A1 - Rethmeier, Michael T1 - In-situ analysis of solid state phase transformation in TRIP-aided steels by synchrotron diffraction N2 - Energy dispersive synchrotron diffraction (EDXRD) analysis and 3 dimensional digital image correlations were conducted to investigate the stress and strain effected transformation behavior during tensile loading of low alloyed TRansformation Induced Plasticity (TRIP) steel. This technique allowed for phase specific stress measurement during certain tensile load steps in the elastic and also plastic regime. Additionally the simultaneous determination of the load dependent phase content was realized. The results show that the martensite transformation starts only after exceeding the overall yield point and is finished before reaching the uniform elongation, whereas a large portion of the austenite remains unchanged in the structure. Furthermore, the martensite transformation related to the stress in the γ-phase and α-phase was analyzed and quantified. KW - Synchrotron KW - EDXRD KW - Phase transformation KW - TRIP steel KW - Digital image correlation KW - Residual stress PY - 2011 UR - https://www.jstage.jst.go.jp/article/qjjws/29/3/29_3_81s/_pdf DO - https://doi.org/10.2207/qjjws.29.81s SN - 0288-4771 VL - 29 IS - 3 SP - 81 EP - 85 CY - Tokyo, Japan AN - OPUS4-24693 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wagner, Ricarda A1 - Biyikal, Mustafa A1 - Wan, Wei A1 - Rurack, Knut A1 - Sellergren, B. T1 - Targeting biological and environmental analytes using imprinted chromogenic or fluorgenic receptors T2 - 2. Junges Chemie Symposium Ruhr CY - Essen, Germany DA - 2011-09-22 PY - 2011 AN - OPUS4-24697 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan T1 - Ganzheitliche Nachhaltigkeitsbewertung von Recyclingoptionen für mineralische Abbruchmaterialien T2 - 3. Betonfachtagung Nord CY - Braunschweig, Germany DA - 2011-09-29 PY - 2011 AN - OPUS4-24718 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Recknagel, Christoph T1 - Erfahrungen mit flexiblen Fahrbahnübergängen und Stand der Technik in Deutschland T2 - Vortrag im Rahmen der EMPA-Tagung über den Bewährungsnachweis für flexible Übergangskonstruktionen und Ausblick auf erweiterte Leistungspotentiale aufgrund neuer Untersuchungen CY - Dübendorf, Switzerland DA - 2011-10-18 PY - 2011 AN - OPUS4-24719 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan A1 - Rübner, Katrin A1 - Meng, Birgit A1 - Hauer, B. T1 - Sustainable evaluation - concepts to assess the applicability of secondary aggregates concrete T2 - SB11 Helsinki, World Sustainable Building Conference CY - Helsinki, Finland DA - 2011-10-18 PY - 2011 AN - OPUS4-24720 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiggenhauser, Herbert T1 - NDT-CE Challenges and Lessons learned T2 - SIBTEST 2011, NDT-Workshop CY - Gorny, Altai Krai, Russia DA - 2011-07-25 PY - 2011 AN - OPUS4-24721 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Influence of Selected Aspects of the Mixture Proportioning on the Performance of Repair Mortars T2 - Concrete Solutions 2011, 4th International Conference Repair CY - Dresden, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-24723 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiele, Marc A1 - Baeßler, Matthias A1 - Rogge, Andreas A1 - Pirskawetz, Stephan ED - Rogge, A. ED - Meng, B. T1 - Schädigungsevolution in Beton unter hochzyklischen Ermüdungsbeanspruchungen N2 - Unter zyklischen Belastungen findet im Beton, wie bei anderen Materialien auch, ein Ermüdungsprozess statt. Im derzeitigen Erkenntnisstand zum Materialverhalten des heterogenen Betons gibt es gerade bei dessen Ermüdungsverhalten momentan noch viele nicht oder nicht ausreichend geklärte Fragestellungen. Deshalb befasst sich der vorliegende Beitrag mit der experimentellen Untersuchung des Ermüdungsverhaltens von Beton, speziell unter hochzyklischen Druckschwellbelastungen. Im Fokus der Untersuchungen stehen dabei die während der gesamten Lebensdauer im Materialgefüge ablaufenden Prozesse, die zu Veränderungen im Materialverhalten und schließlich auch bis zum Ermüdungsversagen führen können. Ziel ist es, eine möglichst realitätsnahe Beschreibung des im Materialgefüge ablaufenden Ermüdungsprozesses zu entwickeln. T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Germany DA - 07.11.2011 KW - Beton KW - Ermüdung KW - Schädigung PY - 2011 SN - 978-3-9814281-0-0 IS - E4 SP - 172 EP - 181 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-24724 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Taffese, W.Z. A1 - Kumaran, G.S. A1 - Uzoegbo, H.C. A1 - Kühne, Hans-Carsten T1 - LightSHIP II: Inorganic Binder Systems for Innovative Panel Technology in East Africa T2 - Workshop Cement and Concrete for Africa CY - Berlin, Germany DA - 2011-08-17 PY - 2011 AN - OPUS4-24725 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter T1 - Combustion of peroxy-fuels N2 - The diffusion flames of organic peroxides exhibit quite different characteristics than hydrocarbons. What makes them interesting to study is their fast burning behaviour. As a result the flame temperature enhances and so does the thermal radiation. Due to all these they demand safe handling during processing. However, they can be utilised at several places in different industries where a fuel with fast burning, high temperature and intense radiation are desired. Some of the possibilities to use them as a main or supporting fuel in a wide range of industrial utilities are the major content of this paper. T2 - ERCOFTAC conference - Highly resolved experimental and numerical diagnostics for turbulent combustion CY - Rouen, France DA - 25.05.2011 KW - Energetic materials KW - Process industries KW - Organic peroxide KW - Di-tert-butyl peroxide (DTBP) KW - CFD simulation KW - Emission PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-247083 SP - 1 EP - 5 AN - OPUS4-24708 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubcová, Petra A1 - Rübner, Katrin A1 - Schnell, A. T1 - Nachhaltige Verwertung von Bau- und Abbruchabfällen im Bausektor T2 - Tagung Bauchemie CY - Hamburg, Germany DA - 2011-10-06 PY - 2011 AN - OPUS4-24711 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten A1 - Ramge, Peter A1 - Meng, Birgit T1 - Repair Mortars for the Restoration and Reprofiling of Natural Stone Elements in Cultural Heritage T2 - DEWCHP-2011, European Workshop and Training Day on Cultural Heritage Preservation CY - Berlin, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-24712 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - Übersicht zur Normungsarbeit an der DIN 19573 "Mörtel für Neubau und Sanierung von Entwässerungssystemen außerhalb von Gebäuden" T2 - "Das Bauen mit Beton aus dem Blickwinkel der Dauerhaftigkeit und neuer Regelwerke", 3. Betonfachtagung Nord 2011, TU Braunschweig CY - Braunschweig, Germany DA - 2011-09-29 PY - 2011 AN - OPUS4-24713 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pistol, Klaus A1 - Weise, Frank A1 - Meng, Birgit T1 - The mode of action of polypropylene fibres in high performance concrete at high temperatures T2 - 2nd international RILEM workshop on concrete spalling due to fire exposure CY - Delft, Netherlands DA - 2011-10-05 PY - 2011 AN - OPUS4-24714 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pistol, Klaus A1 - Korzen, Manfred A1 - Weise, Frank T1 - Monitoring of fire damage processes in concrete by pore pressure and acoustic emission measurements T2 - 2nd international RILEM workshop on concrete spalling due to fire exposure CY - Delft, Netherlands DA - 2011-10-05 PY - 2011 AN - OPUS4-24715 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Trowitzsch-Kienast, W. A1 - Rühl, M. A1 - Kim, K.Y. A1 - Emmerling, Franziska A1 - Erben, U. A1 - Somasundaram, R. A1 - Freise, C. T1 - Absolute configuration of antifibrotic (+)-episesamin isolated from Lindera obtusiloba BLUME N2 - Fractionation of a 70% ethanolic extract from twigs of Lindera obtusiloba BLUME (Japanese spicebush, Tohaku) yielded fi ve fractions of different polarity. The antifi brotic activity within the chloroform phase was best assessed by an in vitro bioassay using rat hepatic stellate cell (HSC) proliferation and their autocrine transforming growth factor beta (TGF-β) expression as sensitive fibrosis-associated read out. Chromatography of the chloroform extract on Sephadex LH-20 or liquid-liquid extractions yielded a crystalline compound as an active principle, which was identifi ed from NMR and ESI-MS analyses, its melting point, and its optical rotation as (7S,7'S,8S,8'S)-3,4:3',4'-bis(methylenedioxy) -7,9':7',9-diepoxy-lignane [(+)-episesamin]. X-Ray diffraction confirmed the structure and provided, for the fi rst time, directly its absolute confi guration. (+)-Episesamin blocked proliferation and the profi brotic autocrine TGF-β expression HSC without signifi cant cytotoxicity. KW - TGF-beta KW - Liver Fibrosis KW - X-Ray Structure PY - 2011 SN - 0939-5075 SN - 0341-0382 SN - 0341-0471 VL - 66c IS - 9/10 SP - 460 EP - 464 PB - Verl. d. Zeitschrift für Naturforschung CY - Tübingen AN - OPUS4-24716 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubcová, Petra A1 - Rübner, Katrin A1 - Schnell, A. T1 - Leichtgranulate aus heterogenem Bauschutt zur Herstellung von Beton N2 - Untersucht wird die Entwicklung einer Technologie zur Herstellung hochwertiger Leichtgranulate (Blähgranulate) mit definierten Produkteigenschaften aus heterogenen Bau- und Abbruchabfällen, Anwendung der Granulate als leichte Gesteinskörnung im Beton und die Möglichkeit des rohstofflichen Recyclings mineralischer Bauabfälle T2 - r2- Statusseminar 2011, "Innovative Technologien für Ressourceneffizienz - rohstoffintensive Produktionsprozesse, Fraunhofer-Institut CY - Berlin, Germany DA - 26.10.2011 PY - 2011 AN - OPUS4-24717 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krischok, Frank A1 - Schulte, Petra T1 - Klassifizierung von Gefahrgütern nach deren Eigenschaften und Anforderungen an Verpackungen und Kennzeichnungen entsprechend der Anlage zum Euopäischen Übereinkommen über die internationale Beförderung gefährlicher Güter auf Binnenwasserstraßen (ADN) T2 - Forbildungsseminar der Sonderstelle für Aus- und Fortbildung "Berförderung gefährlicher Güter auf Binnengewässern" CY - Hanover, Germany DA - 2011-11-15 PY - 2011 AN - OPUS4-24758 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröder, Volkmar T1 - Verlässliche Datenquellen - Darstellung der Kenngrößen in der Datenbank CHEMSAFE T2 - DECHEMA-Weiterbildungskurs "Grundlagen und rechtliche Anforderungen des Explosionsschutzes" CY - Frankfurt am Main, Germany DA - 2011-11-09 PY - 2011 AN - OPUS4-24759 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Reducing ground-borne micro-vibrations by plate foundations T2 - ICOVP International Conference on Vibration Problems CY - Prague, Czech Republic DA - 2011-09-05 PY - 2011 AN - OPUS4-24760 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - High-speed railway tracks of a surface, bridge and tunnel line and some effects on train-induced bridge and ground vibrations. T2 - Conference on Computational Methods in Structural Dynamics and Earthquake Engineering (COMPDYN) CY - Corfu, Greece DA - 2011-05-25 PY - 2011 AN - OPUS4-24761 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Rechenergebnisse zur Erschütterungsminderung der besohlten Schwelle T2 - RIVAS (Railway induced vibration abutment solutions) Meeting Subtask 3.2.1 CY - Berlin, Germany DA - 2011-11-03 PY - 2011 AN - OPUS4-24762 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Anforderungen an die Materialeffizienz unter der Ökodesign-Richtlinie und ihre Umsetzung T2 - Praxisdialog Ressourceneffizienz, BMWi CY - Berlin, Germany DA - 2011-11-02 PY - 2011 AN - OPUS4-24763 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feistkorn, Sascha T1 - Zerstörungsfreie Prüfung im Bauwesen - Die Anwendung der POD am Beispiel des Impulsradars T2 - 332. Sitzung des DGZfP Arbeitskreises CY - Berlin, Germany DA - 2011-06-07 PY - 2011 AN - OPUS4-24766 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feistkorn, Sascha A1 - Taffe, Alexander T1 - Zerstörungsfreie Prüfverfahren im Bauwesen - Möglichkeiten und Grenzen der Messmethoden T2 - 22. Vortragsveranstaltung der LGG Hessen-Thüringen "Bauwerke Instandsetzen - heute und morgen" CY - Bad Nauheim, Germany DA - 2011-11-10 PY - 2011 AN - OPUS4-24767 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grätz, Rainer T1 - Normung im Bereich des Explosionsschutzes -nicht elektrisch- T2 - DECHEMA Weiterbilungskurs "Grundlagen und rechtliche Anforderungen des Explosionsschutzes" CY - Frankfurt am Main, Germany DA - 2011-11-09 PY - 2011 AN - OPUS4-24729 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grätz, Rainer T1 - Rechtliche Anforderungen des Explosionsschutzes T2 - DECHEMA Weiterbildungskurs "Grundlagen und rechtliche Anforderungen des Explosionsschutzes" CY - Frankfurt am Main, Germany DA - 2011-11-09 PY - 2011 AN - OPUS4-24730 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bachmann, Marcel A1 - Avilov, Vjaceslav A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Multiphysics Process Simulation of the Electromagnetic-Supported Laser Beam Welding T2 - COMSOL Conference CY - Stuttgart, Germany DA - 2011-10-26 PY - 2011 AN - OPUS4-24731 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ünal, Murat A1 - Kleine, M. A1 - Kühne, Hans-Carsten T1 - Entwicklung von Betonergänzungsmassen und Instandsetzungsprinzipien zur Restaurierung von Betonglasfenstern des 20. Jahrhunderts T2 - Stained Glass After 1920: Technology and Conservation Forum for the Conservation of Stained-Glass Windows CY - Lisbon, Portugal DA - 2011-09-26 PY - 2011 AN - OPUS4-24732 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin A1 - Adam, Christian A1 - Matyschik, Jan T1 - Optimierung von Rückbau und Aufbereitung von Altbeton T2 - 52. DAfStb-Forschungskolloquium 2011, Innovative Forschung für den Betonbau CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-24733 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thöns, Sebastian T1 - Inspection and monitoring supported structural integrity management T2 - BAM-DTU Workshop on Design and maintenance of support structures for Offshore Wind Converters CY - Copenhagen, Denmark DA - 2011-10-25 PY - 2011 AN - OPUS4-24734 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thöns, Sebastian T1 - Structural reliability assessment and integrity management optimisation T2 - BAM-DTU Workshop on Design and maintenance of support structures for Offshore Wind Converters CY - Copenhagen, Denmark DA - 2011-10-25 PY - 2011 AN - OPUS4-24735 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Computational models and experimental testing of offshore foundations at BAM - Current works and open issues T2 - BAM-DTU Seminar on Design and maintenance of support structures for Offshore Wind Converters CY - Copenhagen, Denmark DA - 2011-10-25 PY - 2011 AN - OPUS4-24737 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Said, Samir A1 - Auersch, Lutz T1 - Experimental soil parameters by different evaluation methods for impulsive, train and ambient excitation T2 - 5th Int. Symp. on Environmental Vibration (ISEV) CY - Chengdu, China DA - 2011-10-20 PY - 2011 AN - OPUS4-24738 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Acikalin, Hatice Aydan T1 - Schutzkonzepte I - Grundlagen zur sicheren Durchführung chemischer Reaktionen T2 - DECHEMA-Weiterbildung "Sicherheit chemischer Reaktionen" CY - Berlin, Germany DA - 2011-03-28 PY - 2011 AN - OPUS4-24739 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Acikalin, Hatice Aydan T1 - Schutzkonzepte II Druckentlastung und Rückhaltung von gefährlichen Stoffen aus Druckentlastungseinrichtungen T2 - DECHEMA-Weiterbildungskurs "Sicherheit chemischer Reaktionen" CY - Berlin, Germany DA - 2011-03-28 PY - 2011 AN - OPUS4-24740 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dabah, Eitan A1 - Kannengießer, Thomas A1 - Eliezer, D. A1 - Böllinghaus, Thomas T1 - Influence of hydrogen on the residual stresses in super martensitic stainless steel T2 - MECA SENS VI CY - Hamburg, Germany DA - 2011-09-07 PY - 2011 AN - OPUS4-24741 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heinze, Christoph A1 - Schwenk, Christopher A1 - Rethmeier, Michael A1 - Nagumothu, Kishore Babu T1 - Numerical Analysis of Welding Induced Residual Stresses Regarding Dependency of Martensite Strat Temperature on Austenite Grain Size T2 - Konferenz "Materials Science and Technology 2011" CY - Columbus, OH, USA DA - 2011-10-16 PY - 2011 AN - OPUS4-24742 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Illerhaus, Bernhard A1 - Meinel, Dietmar T1 - Computertomographie für die Schadensanalyse T2 - VDI-Jahrestagung Schadensanalyse CY - Würzburg, Germany DA - 2011-10-19 PY - 2011 AN - OPUS4-24744 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fontana, Patrick A1 - Lehmann, Christian A1 - Müller, Urs A1 - Meng, Birgit A1 - Kühne, Hans-Carsten A1 - Rogge, Andreas T1 - Wärmebehandlung und Autoklavierung von UHPC - Einfluss auf Mikrostruktur und mechanische Eigenschaften T2 - Feuerfestkolloquium 2011, Fachsymposium "Fertigteile aus UHPC - Fertigungspartner Feuerfestindustrie?" CY - Aachen, Germany DA - 2011-10-20 PY - 2011 AN - OPUS4-24745 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric A1 - Gregor, Christian A1 - Bohse, Jürgen T1 - Überwachung der Fertigungsqualität von Faserverbund - Druckbehältern mittel Schallemissionsprüfung T2 - 18. Kolloquium Schallemission (DGZfP) CY - Wetzlar, Germany DA - 2011-10-26 PY - 2011 AN - OPUS4-24746 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheid, Marc T1 - Übersichtsvortrag Staubexplosionsgefahren und Beispiele für Schutzmaßnahmen T2 - Seminar "Brand- un Explosionsschutz" CY - Schierke, Germany DA - 2011-11-09 PY - 2011 AN - OPUS4-24749 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rauchegger, Christian A1 - Schalau, Bernd A1 - Schmidt, Dirk A1 - Lohse, Volkmar A1 - Schröder, Volkmar A1 - Thévenin, D. T1 - Experimental Results from Heavy Gas Dispersions (R134a) T2 - 7th Global Congress on Process Safety (GCPS) CY - Chicago, IL, USA DA - 2011-03-13 PY - 2011 AN - OPUS4-24750 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheid, Marc A1 - Schmidt, Martin A1 - Lohrer, Christian T1 - Sichere Handhabung brennbarer Stäube T2 - DECHEMA-Seminar "Grundlagen und rechtliche Anforderungen des Explosionsschutzes" CY - Frankfurt am Main, Germany DA - 2011-11-09 PY - 2011 AN - OPUS4-24751 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Berger, Anka T1 - Self-heating Solids EU method A.16 - UN test N.4 T2 - ECHA Training Course "Physical and Chemical Properties" CY - Berlin, Germany DA - 2011-10-24 PY - 2011 AN - OPUS4-24752 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Knorr, Annett T1 - Exotherme Reaktionen: Grundlagen der Wärmebilanz und Untersuchungsmethoden T2 - Seminar der BG RCI "Sicheres Betreiben chemischer Prozesse, Schwerpunkt: Exotherme Reaktionen" CY - Maikammer, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-24753 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröder, Volkmar T1 - Grundlagen des Explosionsschutzes - Eine Einführung T2 - DECHEMA-Weiterbildungskurs "Grundlagen und rechtliche Anforderungen des Explosionsschutzes" CY - Frankfurt am Main, Germany DA - 2011-11-09 PY - 2011 AN - OPUS4-24754 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Michael-Schulz, Heike T1 - Explosive Properties T2 - ECHA Trainig Course "Physical and Chemical Properties" CY - Berlin, Germany DA - 2011-10-24 PY - 2011 AN - OPUS4-24755 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulte, Petra T1 - Einstufung und Kennzeichnung von Stoffen und Gemischen nach GHS/CLP T2 - Arbeitskreis Sicherheitsmanagement Berlin-Brandenburg CY - Berlin, Germany DA - 2011-10-28 PY - 2011 AN - OPUS4-24756 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröder, Volkmar T1 - Sicherheitstechnische Kenngrößen von Gasen und Gasgemsichen T2 - DECHEMA-Weiterbildungskurs "Grundlagen und rechtliche Anforderungen des Explosionsschutzes" CY - Frankfurt am Main, Germany DA - 2011-11-09 PY - 2011 AN - OPUS4-24757 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Köth, A. A1 - Appelhans, Dietmar A1 - Robertson, Daniela A1 - Tiersch, B. A1 - Koetz, J. T1 - Use of weakly cationic dendritic glycopolymer for morphological transformation of phospholipid vesicles into tube-like networks N2 - Using cationic polyelectrolytes with different molecular architectures, only hyperbranched poly(ethyleneimine) with maltose shell is suited to tailor the morphological transformation of anionic vesicles into tube-like networks. The interaction features of those materials partly mimic biological features of tubular proteins in nature. KW - Cationic phospholipid vesicles KW - Anionic polyelectrolyte KW - Morphological transformatio PY - 2011 DO - https://doi.org/10.1039/c1sm06439h SN - 1744-683X VL - 7 SP - 10581 EP - 10584 PB - RSC Publ. CY - Cambridge AN - OPUS4-25070 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ortwein, Hans-Peter A1 - Trappe, Volker A1 - Bohse, Jürgen A1 - Hickmann, Stefan T1 - In-Situ-Messung der Matrixschädigung in kohlenstofffaserverstärktem Kunststoff unter uni- und biaxialer Zugbelastung - In-situ-monitoring of matrix degradation in carbonfiber reinforced plastic under uni- and biaxial tension T2 - DVM-Tagung Werkstoffprüfung 2011 CY - Berlin, Germany DA - 2011-12-01 PY - 2011 AN - OPUS4-25071 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabe, Torsten A1 - Naghib Zadeh, Hamid A1 - Glitzky, C. A1 - Töpfer, J. T1 - Integration of Ni-Cu-Zn ferrite in LTCC-modules N2 - Integration of magnetic functional components in LTCC Circuit boards calls for co-firing of dielectric and ferrite tapes. Ni-Cu-Zn ferrites with permeability of p=900 were developed which can be fully densified at the Standard LTCC sintering temperature of 900 °C. Successful co-firing of this ferrite with dielectric tapes requires the adaptation of the shrinkage behavior of the materials as well as the thermal expansion during the cooling period - especially in the temperature range below the transformation point of the glassy phase of the dielectric tape. To match these preconditions, a new dielectric LTCC material with steep sintering curve and high thermal expansion coefficient was designed. Sintered multilayer composed of Ni-Cu-Zn ferrite and tailored dielectric tapes are free of cracks and possess no open porosity. No significant interdiffusion between the ferrite and dielectric tapes was found by EDX measurements. Compared to pure ferrite laminates the permeability of co-sintered Ni-Cu-Zn ferrite layers is drastically reduced to 400, i.e. a decrease of more than 50 %. To investigate the origin of this permeability reduction, Ni-Cu-Zn ferrite laminates were sintered separately, and in combination with alumina release tapes or dielectric tapes, respectively. SEM and EDX analysis of co-fired laminates reveal differences in the ferrite grain growth behavior. Ferrite laminates with homogeneous microstructure and grain size up to 50 pm exhibit large permeability. However, growth of ferrite grains does not take place near the interface between ferrite and release or dielectric tapes. There is a strong correlation between high permeability and volume fraction of large ferrite grains. Regions of fine and coarse grains inside the ferrite layers show different bismuth concentration; the Bi-content is larger in regions of fine ferrite grains. T2 - CICMT 2011 - 7th International conference and exhibition on ceramic interconnect and ceramic microsystems technologies CY - San Diego, CA, USA DA - 05.04.2011 KW - LTCC KW - Co-firing KW - Ferrite KW - Shrinkage behavior KW - Constrained sintering KW - Keramische Multilayer KW - Grenzflächenreaktion PY - 2011 SN - 0-930815-92-0 SP - 000266 EP - 000275 PB - IMAPS, International Microelectronics and Packaging Society AN - OPUS4-25072 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Blind, K. A1 - Jungmittag, A. A1 - Mangelsdorf, Axel T1 - The economic benefits of standardization - An update of the study carried out by DIN in 2000 N2 - Economists have been searching for the sources of economic growth since the end of the 18th century. For Adam Smith the division of labour and the accumulation of capital were causes for the increasing wealth of nations. The Austrian-American economist Joseph Alois Schumpeter further established that innovations in products and processes are prerequisites for economic growth: »The fundamental drive that starts up the capitalist machine and keeps it running comes from the new consumer goods, the new production and transport methods, the new markets, the new forms of industrial organisation, which capitalist entrepreneurship creates.« Building on these fundamental ideas, during the 1950s American Robert M. Solow – later a Nobel prize winner – developed the first formal mathematical model of economic growth. Solow was able to use a simple model to Show that economic growth within the USA could be described by three determinants: an increase in capital (e.g. machinery and infrastructure), an increase in labour, and technical progress. Later other economists were able to further refine Solow‘s growth theory. While technical progress was accepted during the early years as a fact, it became ever easier to theoretically describe and quantify its causes. The central idea of these new models is that the state and businesses invest in research and development, thus continually stimulating economic growth through new products and production methods. KW - Standards KW - Economic growth KW - Value KW - Technical progress PY - 2011 SP - 1 EP - 20 CY - Berlin AN - OPUS4-25073 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mangelsdorf, Axel T1 - The role of technical standards for trade between China and the European Union N2 - The paper addresses the role of technical standards in bilateral trade relationship between the European Union (EU) and China. Traditional aggregate demand functions for imports and exports have been applied to estimate the effects of national and international standards. The panel dataset covers 14 years (1995–2008) and 36 two-digit technological fields based on the International Classification of Standards (ICS). The results indicate negative effects of purely national Chinese standards but positive effects of Chinese international standards for European exports. European standards and European standards aligned with international standards have a positive impact on exports and imports. Based on these results, we conclude that both China and the EU should increase their efforts to harmonise national standards. KW - Technical barriers to trade KW - Standards KW - Panel analysis KW - Standardisation policy PY - 2011 DO - https://doi.org/10.1080/09537325.2011.592267 SN - 0953-7325 VL - 23 IS - 7 SP - 725 EP - 743 PB - Routledge, Taylor & Francis CY - Abingdon, Oxfordshire AN - OPUS4-25074 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Manke, I. A1 - Kupsch, Andreas A1 - Kardjilov, N. A1 - Schäfer, R. A1 - Grothausmann, R. A1 - Hilger, A. A1 - Strobl, M. A1 - Dawson, M. A1 - Grünzweig, C. T1 - Three-dimensional imaging of magnetic domains T2 - HZB User Meeting 2011 CY - Berlin, Germany DA - 2011-11-30 PY - 2011 AN - OPUS4-25075 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grasse, Fabian A1 - Trappe, Volker A1 - Thöns, Sebastian A1 - Said, Samir ED - De Roeck, G. ED - Degrande, G. ED - Lombaert, G. ED - Müller, G. T1 - Structural health monitoring of wind turbine blades by strain measurement and vibration analysis N2 - Wind turbine blades have to withstand a high number of load cycles in mostly hard weather conditions over 20 years. In a research project BAM and several partners have designed, evaluated and tested a condition monitoring system for all parts of a wind turbine. At a rotorblade with a length of 58 m fibre bragg grating sensors were applied for in-service strain measurement. Additionally a complex test rig was designed to enable real biaxial loading conditions at a representative test rotor blade to simulate the mechanical loading conditions in the lab. In this test blade with a length of 8 m also fibre bragg grating sensors were implemented to determine their influences for the structure and the condition monitoring system. Vibration measurements were carried out at different test phases. The results were compared with finite element strain and modal analysis. T2 - EURODYN 2011 - 8th International conference on structural dynamics CY - Leuven, Belgium DA - 04.07.2011 KW - Rotor blade KW - Test blade KW - Modal analysis KW - Condition monitoring PY - 2011 SN - 978-90-760-1931-4 IS - MS25 Tue SP - 3490 EP - 3497 AN - OPUS4-25076 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Arlt, Tobias A1 - Kupsch, Andreas A1 - Haußmann, J. A1 - Krüger, P. A1 - Manke, I. A1 - Grothausmann, R. A1 - Markötter, H. A1 - Lange, Axel A1 - Hentschel, Manfred P. T1 - Tomographic methods for investigation of fuel cell materials T2 - HZB User Meeting 2011 CY - Berlin, Germany DA - 2011-11-30 PY - 2011 AN - OPUS4-25077 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grasse, Fabian A1 - Trappe, Volker A1 - Hickmann, Stefan ED - Grellmann, W. T1 - Zustandsüberwachung von Rotorblättern - Konzeptstudie mittels Bauteilkomponentenversuch T2 - DVM-Tagung Werkstoffprüfung 2011 - Neue Entwicklungen in der Werkstoffprüfung - Herausforderungen an die Kennwertermittlung CY - Berlin, Deutschland DA - 2011-12-01 KW - Rotorblatt KW - Faserverbundwerkstoffe KW - Modalanalyse KW - Zustandsüberwachung KW - Faser-Bragg-Gitter-Sensoren KW - Rotor blade KW - Fibre reinforced plastics KW - Modal analysis KW - Condition monitoring KW - Fibre bragg grating sensors PY - 2011 SN - 978-3-9814516-1-0 SN - 1861-8154 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 643 SP - 167 EP - 172 AN - OPUS4-25078 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tötzke, Chr. A1 - Kupsch, Andreas A1 - Wieder, F. A1 - Manke, I. A1 - Schmidt, V. A1 - Müller, Bernd R. A1 - Lehnert, W. A1 - Hentschel, Manfred P. A1 - Thiedmann, R. T1 - Three Dimesional Analysis, Modeling and Simulation of Microstructures and Transport Processes in Carbon Fiber Based Porous Materials T2 - HZB User Meeting 2011 CY - Berlin, Germany DA - 2011-11-30 PY - 2011 AN - OPUS4-25079 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Antoni, S. A1 - Kunath, K. A1 - Lüth, Peter A1 - Simon, K. A1 - Uhlig, S. T1 - Evaluation of the interlaboratory test on the method UN O.2 / EC A.21 'Test for oxidizing liquids' 2009 - 2010 N2 - For the classification of chemicals, special standardized test procedures have been developed and are used world-wide. Safe handling and use of these chemicals depend on the correct classification which therefore must be based on the precise and correct execution of the tests and their evaluation. In this context interlaboratory tests (round robin tests, interlaboratory comparisons / intercomparisons) are a crucial element of a laboratory's quality system. Participation in interlaboratory tests is explicitly recommended by the standard ISO/IEC 17025. The present document reports on the results of the interlaboratory test 2009/2010 on the test methods UN O.2 “Test for oxidizing liquids” [1] / EC A.21 “Oxidizing Properties (Liquids)” [2] which was organized by the Center for Quality Assurance for Testing of Dangerous Goods and Hazardous Substances. The test methods UN O.2 and EC A.21 are applied to characterize the oxidizing properties of liquid chemical substances or mixtures. To differentiate between chemicals with hazardous / dangerous oxidizing properties and chemicals which are not classified as hazardous / dangerous, the substance’s oxidizing properties are compared to those of a standard reference substance. Since the methods (UN O.2 / EC A.21) were developed and came into force in the early nineties a systematic review concerning the practical application of the test method has not been carried out. KW - Oxidiser KW - Oxidierend KW - Gefahrgut KW - Dangerous goods KW - UN O.2 KW - Prüfmethode KW - Test method PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-250904 SN - 978-3-9814634-0-8 SP - 1 EP - 95 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin ET - Final report AN - OPUS4-25090 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt A1 - Bücherl, T. A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Selective removal of stochastic artefacts from digigal neutron radiographic images T2 - FNDA 2011, Fast Neutron Detectors and Applications, 2 nd international Workshop CY - Ein-Gedi, Israel DA - 2011-11-06 PY - 2011 AN - OPUS4-25092 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trappe, Volker A1 - Grasse, Fabian A1 - Thöns, Sebastian A1 - Said, Samir T1 - Structural health monitoring for wind turbine rotor blades by strain measurement and vibration T2 - EURODYN 2011 CY - Leuven, Belgium DA - 2011-07-04 PY - 2011 AN - OPUS4-25093 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Kunath, K. A1 - Lüth, Peter A1 - Uhlig, S. T1 - Interlaboratory test on the method UN test N.5 / EC A.12 'Substances which, in contact with water, emit flammable gases' 2007 N2 - For the classification of chemicals, special standardized test procedures have been developed and are used world-wide. Safe handling and use of these chemicals depend on the correct classification which therefore must be based on the precise and correct execution of the tests and their evaluation. In this context interlaboratory tests (round robin tests, interlaboratory comparisons / intercomparisons) are a crucial element of a laboratory's quality system. Participation in interlaboratory tests is explicitly recommended by the standard ISO/IEC 17025. The present document reports on the results of the interlaboratory test 2007 on the method UN Test N.5 “Test method for substances which in contact with water emit flammable gases” [1] / EC A.12 “Flammability (contact with water)” [2] which was organized by the Center for Quality Assurance for Testing of Dangerous Goods and Hazardous Substances. In dependence on the chemical structure and/or the physical form and state (e.g. particle size) substances or mixtures may be able to react with water (even water damp / air humidity) under normal ambient temperature conditions. Sometimes this reaction can be violent and/or with significant generation of heat. Especially if gases are evolved this reaction may become dangerous. In addition, it is important to know whether a substance emits flammable gases due to contact with water because special precautions are necessary especially with regard to explosion protection. The methods UN Test N.5 and EC A.12 are applied to characterize chemical substances or mixtures which in contact with water emit flammable gases. To differentiate between chemicals with these properties and chemicals which are not classified as hazardous / dangerous, the substance’s gas evolution rate is determined and compared to the classification criteria(s) in the last step of the test method. In the methods UN Test N.5 / EC A.12 no special laboratory apparatus / measuring technique to determine gas evolving flow is required. However, practical experience shows that the testing procedure for substances and mixtures which in contact with water emit flammable gases is sensitive to a number of influencing factors. Since the methods (UN N.5 / EC A.12) were developed and came into force in the early nineties a systematic review concerning the practical application of the test method has not been carried out. KW - Flammability KW - Entzündbar KW - Gefahrgut KW - Dangerous goods KW - UN N.5 KW - EC A.12 KW - Prüfmethode KW - Test method PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-250944 SN - 978-3-9814634-1-5 SP - 1 EP - 35 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-25094 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trappe, Volker T1 - Praxisgerechte und effiziente Prüfung der Betriebsfestigkeit von Faserverbundwerkstoffen und -bauteilen T2 - TU Hamburg-Harburg, Einladung zum Institutsseminar des Institute of Polymers and Composites, Prof. Schulte CY - Hamburg, Germany DA - 2011-02-24 PY - 2011 AN - OPUS4-25095 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt A1 - Wrobel, Norma A1 - Ewert, Uwe A1 - Krstelj, V. A1 - Zvizdic, D. T1 - Repositioning of the EFNDT WG 5 T2 - Croatian Society of NDT, MATEST 2011 CY - Split, Croatia DA - 2011-11-02 PY - 2011 AN - OPUS4-25096 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ortwein, Hans-Peter A1 - Bohse, Jürgen A1 - Trappe, Volker A1 - Hickmann, Stefan T1 - Mikrorissbildung in Faserkunststoffverbunden als Indikator für die Betriebsfestigkeitsvorhersage T2 - Frühjahrssitzung 2011 der DGM/DVM-AG Materialermüdung CY - Kassel, Germany DA - 2011-04-07 PY - 2011 AN - OPUS4-25097 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt A1 - Wrobel, Norma A1 - Ewert, Uwe A1 - Krstelj, V. A1 - Zvizdic, D. T1 - Repositioning of the EFNDT WG 5 T2 - Croatian Society of NDT, MATEST 2011 CY - Split, Croatia DA - 2011-11-02 PY - 2011 AN - OPUS4-25098 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt T1 - EFNDT Marine Forum T2 - Croatian Society of NDT, Constitutive Meeting of the EFNDT Marine Non-Destructive Forum CY - Split, Croatia DA - 2011-11-03 PY - 2011 AN - OPUS4-25099 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann, Christian A1 - Fontana, Patrick A1 - Müller, Urs A1 - Meng, Birgit T1 - Entwicklung von C-S-H Phasen in autoklaviertem Ultra-Hochleistungs-Beton (UHPC) T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25131 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rücker, Werner A1 - Savidis, S. A1 - Triantafyllidis, T. A1 - Richter, Thomas T1 - Derzeitige und geplante weitere Untersuchungen von Rammpfahlgründungen für Offshorewindkraftanlagen T2 - Workshop "Gründungen von Offshore Windenergieanlagen", TU Berlin CY - Berlin, Germany DA - 2011-03-22 PY - 2011 AN - OPUS4-25133 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mehdianpour, Milad A1 - Stengel, Dominik T1 - MOSYTRAF Monitoringsystem zur Tragverhaltensstudie von Freileitungen unter Böenbeanspruchung T2 - DKE/ETG-Seminar "Normung und Neuerungen bei Freileitungen" CY - Berlin, Germany DA - 2011-12-06 PY - 2011 AN - OPUS4-25134 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rohrmann, Rolf A1 - Rücker, Werner A1 - Said, Samir A1 - Thöns, Sebastian A1 - Trappe, Volker T1 - Integrale Systeme für die Strukturüberwachung, Dauerüberwachung der Anlagenteile "Bauwerk" und "Rotorblätter" T2 - AMA Fachverband für Sensorik: Fokussierte Thementage "Sensorik und Messtechnik für die Windenergie" CY - Mainz, Germany DA - 2011-12-01 PY - 2011 AN - OPUS4-25135 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiele, Marc A1 - Petryna, Y. A1 - Rogge, Andreas T1 - Experimentelle Untersuchung der Schädigungsevolution in Beton unter Ermüdungsbeanspruchungen T2 - Graduiertenkolleg 1462, Bauhaus-Universität Weimar CY - Weimar, Germany DA - 2011-12-06 PY - 2011 AN - OPUS4-25136 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Perret, William A1 - Thater, R. A1 - Alber, U. A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - Approach to assess a fast welding simulation in an industrial envrionment - application for an automotive welded part N2 - Fusion welding processes are widely used for joining metal structures, such as pipes, ships, and cars. In general, these joining processes offer a very good compromise between reliability, safety, cost and maintenance which are important issues in the current economical context. The negative heat effects of welding, i.e. distortions and residual stresses of the welded parts, are well known and many researches in this field have already been done in the last decades in order to minimize them. On the experimental side, many sophisticated procedures have become state of the art to deal with this problem. On the computational side, the improvement of the simulation algorithms and the computing power enables the simulations of many physical phenomena occurring during the welding process. The implementation of welding simulation techniques is nevertheless not an easy task and often associated with expert knowledge which hinders their global application in an industrial environment. This paper is focused on the industrial requirements of a welding simulation software with special respect to the needs of the automotive industry. The necessary information to run a welding simulation and the expectations of a weld specialist without deep knowledge in numerical methods are investigated. These expectations are tested on an automotive welded assembly with a commercially available welding simulation software designed especially for the needs of the automotive industry. A welding experiment is done and the measured temperature distributions and distortions serve as reference to validate the simulation results. The result quality of the simulations of temperature fields and distortions is in best agreement with experimental data. The workflow is well adapted for the considered industrial requirements and the time-tosolution as well as the computational costs are acceptable, whereas the efficient calibration of the heat input model is still a point which will be further investigated in current and future research works. KW - Welding simulation KW - Distortion KW - Automotive industry KW - Work-flow KW - Time-to-solution KW - Simufact.welding PY - 2011 DO - https://doi.org/10.1007/s12239-011-0102-0 SN - 1229-9138 VL - 12 IS - 6 SP - 895 EP - 901 PB - KSAE / Springer CY - Seoul / Berlin ; Heidelberg AN - OPUS4-25139 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühn, Julius A1 - Lippitz, Andreas A1 - Gross, Thomas A1 - Gorgoi, M. A1 - Like, S. A1 - Moritz, W. A1 - Unger, Wolfgang T1 - Chemical Depth Profiles of Ternary Pd Alloys by HAXPES and First Spectra Simulations T2 - HZB User Metting 2011 CY - Berlin, Germany DA - 2011-12-01 PY - 2011 AN - OPUS4-25060 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wloka, Monika T1 - Einführung in Zielsetzung, Ablauf des Verfahrens der Novellierung und Überblick über die Änderungen der DIN EN ISO 19011:2002 T2 - DGQ/DIN/DQS-Kooperationsveranstaltung DIN EN ISO 19011 Revision CY - Berlin, Germany DA - 2011-06-06 PY - 2011 AN - OPUS4-25061 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt A1 - Wrobel, Norma A1 - Fratzscher, Daniel A1 - Jechow, Mirko A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Einstrahlgeometrie und Erkennbarkeit von Objekten in der Röntgenrückstreuradiographie N2 - Abweichend von der gängigen Vorgehensweise, mit einem Bleistiftstrahl die Lage eines Bildpunktes festzulegen und die rückgestreute Strahlung großflächig aufzunehmen, bietet die neu entwickelte Kamera Unabhängigkeit von Einstrahl- und Blickrichtung. Ausgestattet mit einer 'Optik' für hochenergetische Strahlung, wie die bereits beschriebene Schlitzblendenkamera, ist die variable Gestaltung von Einstrahl- und Blickrichtung möglich. Damit eröffnet sich die Chance, Strahlung absorbierende Details in einem Objekt sichtbar werden zu lassen, die sonst von einer streuenden Umgebung überstrahlt würden. Zudem wird gezeigt, wie sich das Erscheinungsbild von Objekten umgebungsbedingt im Rückstreubild ändern kann. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Deutschland DA - 30.05.2011 KW - Röntgenrückstreuradiographie KW - Schlitzblendenkamera KW - Varibale Einstrahlgeometrie PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-250627 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Poster 20) SP - 1 EP - 5 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25062 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt A1 - Ewert, Uwe A1 - Zvizdic, D. A1 - Krstelj, V. T1 - Die EFNDT Arbeitsgruppe 5 'Öffentliche Sicherheit mit ZfP-Techniken' neu formiert N2 - Für die öffentliche Sicherheit wird gesorgt, indem Gefahren rechtzeitig entdeckt werden. Deren Ursprung kann im technischen oder menschlichen Versagen liegen, womit im englischen Sprachraum zwischen 'Safety' und 'Security' unterschieden wird. Hinsichtlich der Folgen verschwimmt aber dieser Unterschied, obwohl für deren Verhinderung unterschiedliche Zuständigkeiten existieren. Bezüglich des gemeinsamen Interesses und auch überlappender Methoden und Vorgehensweisen würden beide Seiten gewinnen können, wenn es eine Brücke zwischen ihnen gäbe. Eine solche zu schaffen hat sich die EFNDT Arbeitsgruppe (Working Group) 5 zur Aufgabe gestellt. Gestaltet werden soll sie durch gemeinsame Veranstaltungen und Seminaren, die zur Bildung von Konsortien und der Durchführung gemeinsamer Projekte führen sollen. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 03.05.2011 KW - EFNDT Working Group 5 KW - Technische und öffentliche Sicherheit KW - Gemeinsamkeiten in ZfP und öffentlicher Sicherheit KW - Brückenbildung zwischen Zuständigkeitsbereichen PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-250631 SN - 978-3-940283-33-7 VL - 127 SP - 1 EP - 5 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-25063 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt A1 - Fratzscher, Daniel A1 - Zscherpel, Uwe A1 - Ewert, Uwe A1 - Hasenstab, A. A1 - Bücherl, T. A1 - Schillinger, B. T1 - Partielle Tomographie mit Neutronen zur Beurteilung von Leimschichten in Holz N2 - Verleimte Holzproben wurden je nach Größe mit thermischen (ANTARES) bzw. schnellen Neutronen (NECTAR) an der Forschungs-Neutronenquelle Heinz Maier-Leibnitz (FRM II) der Technischen Universität München in Garching untersucht. Entweder ließen die durchstrahlbare Schichtdicke oder die eingeschränkte Strahlgeometrie es nicht zu, das Probenteil allseitig zu durchstrahlen. Um dennoch innere Strukturen wie Leimschichten zumindest mit einem eingeschränkten Winkelbereich tomographisch darzustellen, wurde mit Hilfe des Slice-Theorems erfolgreich rekonstruiert. Ein Brett von 2 cm Dicke wurde mit thermischen Neutronen erfolgreich untersucht, ein größeres mit schnellen. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Neutronentomographie KW - Eingeschränkter Winkelbereich KW - Holz PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-250649 SN - 978-3-940283-33-7 VL - 127 SP - 1 EP - 6 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-25064 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Osterloh, Kurt T1 - Aims and objectives of the EFNDT working group: 'NDT for public safety and security' N2 - The preservation of human achievements and progress is undoubtedly a pillar of our society. This includes detecting threats in time to prevent disasters that may occur from forces of nature, defective technology, human failure or malicious intent. In this respect, there is arguably no difference between safety and security, though different institutions are involved in the regulation and control of them. However, the unifying rationale ought to result in the building of bridges between them. This is the Working Group's mission. KW - Bridging technical safety and public security PY - 2011 DO - https://doi.org/10.1784/insi.2011.53.6.331 SN - 0007-1137 VL - 53 IS - 6 SP - 331 EP - 333 PB - British Institute of Non-Destructive Testing CY - Northampton AN - OPUS4-25065 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt A1 - Fratzscher, Daniel A1 - Jechow, Mirko A1 - Bücherl, T. A1 - Schillinger, B. A1 - Hasenstab, A. A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Limited view tomography of wood with fast and thermal neutrons N2 - Neutrons are absorbed particularly by hydrogen containing materials so they can be used as a tool for visualising heterogeneous density distributions of organic materials. Penetration limits are set by the layer thicknesses and the neutron energies applied. In case of specimens with a flat shape the situation may be encountered that the object only could be penetrated in selected directions. In addition, the overall size may exceed the beam diameter and thus the viewing window if a certain region of interest should be studied by tomography without destroying the integrity of the specimen. This study shows the capabilities and limits of thermal and fast neutrons to investigate flat wooden specimens such as boards and girders by neutron tomography under such circumstances. Taking projections was impaired either by the limits of penetrability or by the total size of the object. As a consequence, projections were included for reconstruction only from a limited angular range of 90°. It could be shown that an approach based on the slice theorem was capable to visualise structural features along the beam directions while simply omitting the perpendicular ones without causing additional artefacts. Small samples with a thickness of up to 2 cm but several times broader could be studied with the ANTARES facility of the FRM II neutron source in Garching providing thermal neutrons while larger objects required a beam of higher energy as available in the NECTAR facility of the same institution. The fast (fission) neutrons (1.5 – 2 MeV) of this site allowed investigating an area of interest inside a girder with a cross section of 23.5 x 49 cm². Internal features such as inclusions could be detected as well as a heterogeneous density distribution in glue layers. T2 - International symposium on digital industrial radiology and computed tomography CY - Berlin, Germany DA - 20.06.2011 KW - Computed tomography KW - Slice theoreme KW - Limited angle tomography PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-250663 SN - 978-3-940283-34-4 VL - 128 SP - 1 EP - 5 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-25066 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schurig, Michael A1 - Klinger, Christian A1 - Schöne, Dieter A1 - Bork, Claus-Peter A1 - Klingbeil, Dietmar ED - Christ, H.-J. ED - Berger, C. T1 - Very high cycle fatigue testing on an electrodynamic shaker system N2 - Fatigue testing in the VHCF ränge requires testing machines with increased frequencies. However, application of energy-saving resonance testing leads to a linkage between test frequency and specimen Parameters. The frequency ränge and the available forces of the testing machine are limiting possible specimen dimensions. Electrodynamic shakers combine test frequencies up to 4000 Hz with forces in the kN range. Thus, a relatively wide range of tests is possible which allows studying the influence of specimen size on VHCF behaviour. Electrodynamic shakers as well as the respective Computer control Systems and Vibration measurement techniques are well established in scientific and technical applications. We present results of a first study of VHCF testing on electrodynamic shakers conducted at BAM. Test frequency, specimen size and stress levels have been varied. One goal is to balance the needs of materials testing with the Standard test Systems of environmental Simulation to provide a powerful and flexible tool for very high cycle fatigue testing. Further investigation to optimize the technique is required. T2 - VHCF5 - 5th International conference on very high cycle fatigue CY - Berlin, Germany DA - 28.06.2011 KW - Electrodynamic shaker KW - Resonance testing KW - Variable frequency KW - Envrionmental simulation KW - Specimen size KW - Two-degree-of-freedom system KW - VHCF KW - Shaker KW - Elektrodynamisch KW - Prüfung PY - 2011 SN - 978-3-9814516-0-3 SP - 433 EP - 438 AN - OPUS4-25067 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ohm, Katrin A1 - Baer, Wolfram ED - Grellmann, W. T1 - Einfluss der Verfahrenstechnik und der Werkstoffprüfung auf den im Zugversuch zu ermittelnden Verformbarkeitskennwert Agt von Betonstählen N2 - Die Streuung der Agt-Werte von Betonstahl bleibt durch die Variation der Prüfbedingungen (Temperatur, Geschwindigkeit) innerhalb der prüfnormseitig zulässigen Grenzen weitgehend unbeeinflusst. Gleichzeitig führt die Variation der Prüfbedingungen zu einer signifikanten, für die Produktabnahme relevanten Änderung des Niveaus von Agt. Die Auswertemethodik des Zugversuches (Festlegung der Höchstkraft, Wahl des Verfahrens zur Agt-Bestimmung) hat einen signifikanten Einfluss auf Niveau und Streuung von Agt. Es werden Empfehlungen zur Minimierung der Streuung von Agt gegeben. T2 - DVM-Tagung Werkstoffprüfung 2011 - Neue Entwicklungen in der Werkstoffprüfung - Herausforderungen an die Kennwertermittlung CY - Berlin, Germany DA - 01.12.2011 KW - Betonstahl KW - Zugversuch KW - Gesamtdehnung bei Höchstkraft KW - Kennwertstreuung KW - Prüfmethodik KW - Reinforcing steel KW - Tensile test KW - Percentage total extension at maximum force KW - Scatter of results KW - Test method PY - 2011 SN - 978-3-9814516-1-0 SN - 1861-8154 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 643 SP - 279 EP - 284 AN - OPUS4-25068 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt T1 - How can Risk and Reliability being Assessed? T2 - EFNDT Working Group 5 Workshop 2011 CY - Berlin, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-25081 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rücker, Werner T1 - Dynamic behaviour of Offshore Wind energy converters T2 - BAM DTU Workshop on Design and maintenance of support structures for Offshore Wind Converters, Department of Civil Engineering, DTU Technical University of Denmark CY - Copenhagen, Denmark DA - 2011-10-25 PY - 2011 AN - OPUS4-25082 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt T1 - EFNDT Working Group 5, from mines to any kind of threats T2 - EFNDT Working Group Workshop 2011 CY - Berlin, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-25083 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt A1 - Ewert, Uwe A1 - Zvizdic, D. A1 - Krstelj, V. T1 - Die EFNDT Arbeitsgruppe 5 "Öffentliche Sicherheit mit ZfP-Techniken" neu formiert T2 - DGZfP-Jahrestagung 2011, Poster 43 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-25084 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt A1 - Fratzscher, Daniel A1 - Wrobel, Norma A1 - Jechow, Mirko A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Einstrahlgeometrie und Erkennbarkeit von Objekten in der Röntgenrückstreuradiographie T2 - DGZfP-Jahrestagung 2011, Poster 20 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-25085 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubcová, Petra A1 - Rübner, Katrin A1 - Schnell, A. T1 - Leichte Gesteinskörnungen auf der Basis thermisch und hydrothermal hergestellter Blähgranulate aus Abbruchabfällen N2 - Beton mit leichten Gesteinskörnungen (Leichtzuschlägen) ist seit dem Altertum bekannt. Leichte Gesteinskörnungen vulkanischen Ursprungs wurden bereits zur Errichtung der Maya-Pyramiden in Mexiko und von monumentalen Bauwerken im Römischen Reich verwendet. Zu den berühmtesten Beispielen der ersten Anwendung von Leichtbeton in Europa gehören das Kolosseum und das Pantheon in Rom, Hier wurden sowohl natürliche als auch künstliche Zuschlagstoffe, wie Bims, Lava und zerkleinerter Ziegelsplitt, benutzt. Mit steigender Nachfrage nach leichten Gesteinskörnungen und einer weltweit begrenzten Verfügbarkeit natürlicher Leichtzuschläge wurden synthetische leichte Gesteinskörnungen entwickelt. Ihre großtechnische Herstellung begann nach dem Ersten Weltkrieg. Heute werden leichte Gesteinskörnungen in einem breiten Schüttdichtespektrum von 100 bis 1200 kg/m3 hergestellt. Sie stellen einen wichtigen Teil der Gesteinskörnungen in der Baubranche dar. T2 - 15. Seminar 'Beschichtungen und Bauchemie' - Reaktive und filmbildende organische Bindemittel: Der Klimawandel und der Einfluss auf die Rezepturen Teil II CY - Kassel, Germany DA - 29.11.2011 KW - Sekundärrohstoffe KW - Sekundäre Gesteinskörnung KW - Recycling KW - Leichtbeton PY - 2011 SP - 55 EP - 66 AN - OPUS4-25086 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt A1 - Fratzscher, Daniel A1 - Zscherpel, Uwe A1 - Ewert, Uwe A1 - Hasenstab, A. A1 - Bücherl, T. A1 - Schillinger, B. T1 - Partielle Tomographie mit Neutronen zur Beurteilung von Leimschichten in Holz T2 - DGZfP-Jahrestagung 2011, Mi.4.B.2 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-25087 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Priebe, Nsesheye Susan T1 - Managing an EU funded project in light of the SPIN project T2 - DAAD Workshop Nairobi: German/ African Seminar CY - Nairobi, Kenya DA - 2011-10-06 PY - 2011 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. AN - OPUS4-25088 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt A1 - Wrobel, Norma A1 - Ewert, Uwe A1 - Krstelj, V. A1 - Zvizdic, D. T1 - Detection Technologies - Common Concepts in Security and Safety T2 - Future Security 2011 (Fraunhofer) CY - Berlin, Germany DA - 2011-09-05 PY - 2011 AN - OPUS4-25089 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Riedel, Jens A1 - Hoekstra, S. A1 - Jäger, W. A1 - Gilijamse, J.J. A1 - van de Meerakker, S.Y.T. A1 - Meijer, G. T1 - Accumulation of Stark-decelerated NH molecules in a magnetic trap N2 - Here we report on the accumulation of ground-state NH molecules in a static magnetic trap. A pulsed supersonic beam of NH (a1Δ) radicals is produced and brought to a near standstill at the center of a quadrupole magnetic trap using a Stark decelerator. There, optical pumping of the metastable NH radicals to the X3Σ- ground state is performed by driving the spin-forbidden A3Π ← a1Δ transition, followed by spontaneous A → X emission. The resulting population in the various rotational levels of the ground state is monitored via laser induced fluorescence detection. A substantial fraction of the groundstate NH molecules stays confined in the several milliKelvin deep magnetic trap. The loading scheme allows one to increase the phase-space density of trapped molecules by accumulating packets from consecutive deceleration cycles in the trap. In the present experiment, accumulation of six packets is demonstrated to result in an overall increase of only slightly over a factor of two, limited by the trap-loss and reloading rates. KW - Cold matter KW - Stark deceleration KW - Trapping of polar molecules KW - NH KW - High resolution spectroscopy KW - Fluorescence KW - Radical PY - 2011 DO - https://doi.org/10.1140/epjd/e2011-20082-7 SN - 1434-6060 VL - 65 IS - 1-2 SP - 161 EP - 166 PB - Springer CY - Berlin AN - OPUS4-25050 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Emissionen flüchtiger organischer Verbindungen aus Bauprodukten T2 - VDI-Wissensforum "Bauprodukte und gesunde Innenraumluft" CY - Düsseldorf, Germany DA - 2011-12-06 PY - 2011 AN - OPUS4-25051 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Recknagel, Christoph T1 - Die BAM als Partner der Bauwirtschaft T2 - Symposium für Architekten und Ingenieure "Das sichere Abdichtunsdetail", BAM CY - Berlin, Germany DA - 2011-11-17 PY - 2011 AN - OPUS4-25052 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - Kunstsein statt Tuff-Bildhauerbeton T2 - Innovation Beton - Forum Zunkunft Bauen CY - Neumünster, Germany DA - 2011-09-12 PY - 2011 AN - OPUS4-25053 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - Neue Entwicklungen in der Normung für den Schutz und die Instandsetzung von Betonbauwerken T2 - Kolloquium "Sachkundiger Planer - Schadensdiagnose und Instandsetzung", Fortbildungsveranstaltung des Bau-Überwachungsvereins (BÜV) in Kooperation mit der BAM, BAM CY - Berlin, Germany DA - 2011-12-02 PY - 2011 AN - OPUS4-25054 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - Rheology and Performance of Grouts and Self Compacting Concrete T2 - Joint DTU - BAM Seminar on Design and Maintenance of Support Stuctures for Offshore Wind Converters CY - Copenhagen, Denmark DA - 2011-10-25 PY - 2011 AN - OPUS4-25055 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - Research areas with regard to new African-German research-projects BAM Federal Institute for Materials Research and Testing, Department 7 "Safety of Structures, Divison 7.1 "Building Materials" T2 - EiABC, Ethopian Institute ofArchitecture, Building Construction and City Development, Conference on German Ethopian Partnership CY - Addis Ababa, Ethiopia DA - 2011-05-25 PY - 2011 AN - OPUS4-25056 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - LightSHIP Lightweight Construction - Scientific Cooperation for Housing with Innovative Panel Technology T2 - BMBF - Workshop: Partnerships for Sustainable Solutions BMBF, Deutsches Zentrum für Luft- und Raumfahrt (DLR) CY - Bonn, Germany DA - 2011-05-31 PY - 2011 AN - OPUS4-25057 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weise, Frank T1 - Innovative Prüfverfahren und -methodologien zur Charakterisierung frost- und AKR-induzierter Schädigungsprozesse in Betonen T2 - Kolloquium "Sachkundiger Planer - Schadendiagnose und Instandsetzung", Fortbildungsveranstaltung des Überwachungsvereins (BÜV) in Kooperation mit der BAM, BAM CY - Berlin, Germany DA - 2011-12-02 PY - 2011 AN - OPUS4-25058 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weise, Frank T1 - Fassadenbegutachtung am Kollhoff-Hochhaus auf dem Potsdamer Platz in Berlin T2 - Kolloquium "Sachkundiger Planer - Schadensdiagnose und Instandsetzung" , Fortbildungsveranstaltung des Bau-Überwachungsvereins (BÜV) in Kooperation mit der BAM, BAM CY - Berlin, Germany DA - 2011-12-02 PY - 2011 AN - OPUS4-25059 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt A1 - Fratzscher, Daniel A1 - Jechow, Mirko A1 - Bücherl, T. A1 - Schillinger, B. A1 - Hasenstab, A. A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Limited View Tomgraphy of Wood with Fast and Thermal Neutrons T2 - International Symposium on Digital Industrial Radiology and Computed Tomography - Poster 14 CY - Berlin, Germany DA - 2011-06-20 PY - 2011 AN - OPUS4-25100 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt A1 - Wrobel, Norma A1 - Zscherpel, Uwe A1 - Fratzscher, Daniel A1 - Jechow, Mirko A1 - Ewert, Uwe T1 - X-ray Backscatter: The Appearence of Certain Features Depending on the Illumination T2 - Croatian Society of NDT, MATEST 2011 CY - Split, Croatia DA - 2011-11-02 PY - 2011 AN - OPUS4-25101 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wrobel, Norma A1 - Osterloh, Kurt A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Variable irradiation geometry with a nex X-ray backscatter camera for security applications T2 - Future Security 2011 (Fraunhofer) CY - Berlin, Germany DA - 2011-09-05 PY - 2011 AN - OPUS4-25102 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gründer, Klaus-Peter A1 - Köppe, Enrico A1 - Kadoke, Daniel T1 - Optische 3D-Referenzierung eines funkgestützten Multisensorsystems zur Bewegungsanalyse gefährdeter Personen N2 - Ein stereo-fotogrammetrisches Messverfahren wurde zur quantitativen Analyse der Bewegungssignale eines elektrischen Multi-Sensorsystems eingesetzt. Der Vergleich von Weg- und Winkel-Zeitverläufen zeigte bereits eine recht gute Übereinstimmung, verdeutlichte jedoch auch die Notwendigkeit einer weiterzuentwickelnden Kalibriermethodik. Die Stereo-Videogrammetrie hat sich als Referenzverfahren zur Analyse und Validierung dreidimensional ausgelegter elektrischer Bewegungssensorik für den Nahbereich bewährt. T2 - 3D-NordOst 2011 - 14. Anwendungsbezogener Workshop zur Erfassung, Modellierung, Verarbeitung und Auswertung von 3D-Daten CY - Berlin, Germany DA - 08.12.2011 KW - Stereo-Videogrammetrie KW - Funkgestützte Sensorik KW - Bewegungsanalyse PY - 2011 SN - 978-3-942709-03-3 SP - 33 EP - 38 AN - OPUS4-25103 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rücker, Werner T1 - Ongoing research projects and research issues in the Area of offshore wind energy T2 - BAM DTU Workshop on Design and maintenance of support structures for Offshore Wind Converters, Department of Civil Engineering, DTU Technical University of Denmark CY - Copenhagen, Denmark DA - 2011-10-25 PY - 2011 AN - OPUS4-25104 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd A1 - Bienert, Klaus A1 - Schalk, Heike A1 - Molkenthin, A. A1 - Goldschmidt, Sebastian A1 - Niederleithinger, Ernst T1 - Quality control of hydrophobic coatings with an integrated marker element by laser-induced breakdown spectroscopy (LIBS) T2 - Concrete Solutions 2011, 4th International Conference on Concrete Repair CY - Dresden, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-25105 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rücker, Werner T1 - Zuverlässigkeit von Brücken, Verfahren zur Überwachung und Bewertung bestehender Bauwerke T2 - IQPC Konferenz Brücken CY - Darmstadt, Germany DA - 2011-01-24 PY - 2011 AN - OPUS4-25106 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rücker, Werner T1 - Bemessung von Offshore Pfahlgründungen unter zyklischer Belastung - Fragestellungen, Messungen im Testfeld "Alpha Ventus", Anwendung im Genehmigungsverfahren - T2 - Workshop "Gründungen von Offshore Windenergieanlagen", TU Berlin CY - Berlin, Germany DA - 2011-03-22 PY - 2011 AN - OPUS4-25107 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rücker, Werner T1 - Determination of dynamic soil parameters for track-soil interaction and train induced ground vibrations T2 - DB-Eisenbahnseminar CY - Berlin, Germany DA - 2011-05-12 PY - 2011 AN - OPUS4-25108 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ehrig, Karsten A1 - Staude, Andreas A1 - Bartscher, M. T1 - Open questions in CT uncertainty evaluation T2 - CT-Audit-International Workshop on Computed Tomgraphy for Dimensional Metrology CY - Padua, Italy DA - 2011-10-26 PY - 2011 AN - OPUS4-25109 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gnutzmann, Tanja A1 - Ristic, R. I. A1 - Rusin, M. A1 - Emmerling, Franziska T1 - Influencing polymorphism - a time resolved in situ XRD/Raman study on L-glutamic acid T2 - Third Joint BER II and BESSY II Users´ Meeting CY - Berlin, Germany DA - 2011-12-01 PY - 2011 AN - OPUS4-25121 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sarfraz, Adnan A1 - Gnutzmann, Tanja A1 - Emmerling, Franziska A1 - Tremel, W. A1 - Dietzsch, M. T1 - In-situ study of the crystallization of metal (IV) phosphonates T2 - Bessy User Meeting 2011 CY - Berlin, Germany DA - 2011-11-29 PY - 2011 AN - OPUS4-25124 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Riesemeier, Heinrich A1 - Markötter, H. A1 - Manke, I. A1 - Kardjilov, N. A1 - Dittmann, K. A1 - Tötzke, Chr. A1 - Hilger, A. A1 - Wieder, F. A1 - Haußmann, J. A1 - Arlt, Tobias A1 - Klages, M. A1 - Krüger, P. A1 - Wippermann, K. A1 - Schröder, A. A1 - Banhart, J. A1 - Sanders, T. A1 - Alink, R. A1 - Gerteisen, D. T1 - Combined synchrotron X-ray and neutron imaging for the characterization of fuel cells T2 - Third Joint BER II and BESSY II Users´ Meeting CY - Berlin, Germany DA - 2011-11-30 PY - 2011 AN - OPUS4-25125 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Riesemeier, Heinrich A1 - Tötzke, Chr. A1 - Wieder, F. A1 - Manke, I. A1 - Schmidt, V. A1 - Kupsch, Andreas A1 - Lehnert, W. A1 - Thiedmann, R. A1 - Sutmann, G. A1 - Müller, Bernd R. T1 - Three dimensional analysis, modeling and simulation of microstructures and transport processes in carbon fiber based porous materials T2 - Third Joint BER II and BESSY II Users´ Meeting CY - Berlin, Germany DA - 2011-11-30 PY - 2011 AN - OPUS4-25126 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rücker, Werner T1 - Laborversuche zur Ermittlung der dynamischen Bodenparameter T2 - DB-Eisenbahnseminar CY - Berlin, Germany DA - 2011-05-12 PY - 2011 AN - OPUS4-25110 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rücker, Werner A1 - Auersch, Lutz T1 - Modelling and parameters of dynamic track behaviour, train-track interaction and ground vibration T2 - RIVAS Workshop "Vibration mitigation measures on railway tracks" CY - Paris, France DA - 2011-06-09 PY - 2011 AN - OPUS4-25111 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ortwein, Hans-Peter A1 - Bohse, Jürgen A1 - Trappe, Volker A1 - Hickmann, Stefan T1 - Untersuchung des Zwischenfaserrisswachstums in Faserverbundwerkstoffen mit Schallemissions- und Röntgenrefraktionsverfahren T2 - DGZfP-Jahrestagung CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-25112 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rücker, Werner A1 - Said, Samir T1 - Experimental results for WIBS T2 - Workshop "Vibration mitigation measures on transmission/propagation path" CY - Frankfurt am Main, Germany DA - 2011-06-22 PY - 2011 AN - OPUS4-25113 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rücker, Werner T1 - BAMS testfield Horstwalde for WIBS T2 - Workshop "Vibration mitigation measures on transmission/propagation path" CY - Frankfurt am Main, Germany DA - 2011-06-22 PY - 2011 AN - OPUS4-25114 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rücker, Werner T1 - Mitigation measures in the transmission path T2 - Workshop "Vibration mitigation measures on transmission/propagation path" CY - Frankfurt am Main, Germany DA - 2011-06-22 PY - 2011 AN - OPUS4-25115 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rücker, Werner A1 - Rohrmann, Rolf A1 - Said, Samir A1 - Thöns, Sebastian A1 - Schmid, Wolfgang T1 - Dynamisches Verhalten von Windenergieanlagen T2 - VDI-Fachkonferenz: Turm und Fundament von Windenergieanlagen CY - Hamburg, Germany DA - 2011-10-11 PY - 2011 AN - OPUS4-25116 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rücker, Werner A1 - Baeßler, Matthias A1 - Richter, Thomas A1 - Kirsch, Fabian T1 - Interaktion zwischen Boden und Gründungen bei Offshore Windkraftanlagen, - Bemessung von Offshore Pfahlgründungen unter zyklischer Belastung - T2 - VDI-Fachkonferenz: Offshore-Tragstrukturen, Installation & Logistik CY - Bremerhaven, Germany DA - 2011-09-27 PY - 2011 AN - OPUS4-25117 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Gerüche von Bauprodukten - Präsentation Messergebnisse T2 - Gemeinsame Veranstaltung des DIBt, des AgBB, der BAM und des UBA: 1. Fachgespräch zur Geruchsprüfung bei Bauprodukten CY - Berlin, Germany DA - 2011-12-05 PY - 2011 AN - OPUS4-25118 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute T1 - [RES]Check: Dezentrales Diagnostiksystem zur schnellen Erfassung viraler oder bakterieller Erreger respiratorischer Erkrankungen T2 - MEDICA CY - Düsseldorf, Germany DA - 2011-11-16 PY - 2011 AN - OPUS4-25119 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Reiche, I. A1 - Müller, K. A1 - Staude, Andreas A1 - Goebbels, Jürgen A1 - Riesemeier, Heinrich T1 - Synchrotron radiation and laboratory micro X-ray computed tomography - useful tools for the material identification of prehistoric objects made of ivory, bone or antler N2 - Archaeological bone, ivory and antler, as well as objects manufactured from them, are largely studied to extract as much information as possible from these materials. Among others, one key question in archaeology is the exact identification of the material. Even if the identification of different kinds of osseous material seems to be trivial in many cases, it can be a difficult issue when small, heavily carved and more or less altered ancient objects are concerned. This study was focused on the determination of parameters allowing the distinction of archaeological ivory, bone and antler in order to identify the raw material used for the manufacture of prehistoric objects. The high performance of synchrotron radiation (SR) and laboratory-based micro X-ray computed tomography (microCT), providing highly resolved three-dimensional information on the micromorphology, permitted the establishment of such distinctive features of modern references of ivory, antler, land mammal and whale bones: ivory shows characteristic tubular pores with a diameter of about 1 to 2 µm, bone and antler show typical osteon structures. In our measured references, antler shows on average larger and more elongated shaped pores of the osteons compared to terrestrial mammal bone. This feature however depends very much on the original localization of the studied sample within the antler. Whale bones can be distinguished from the other osseous materials by a cancellous, osteoporotic-like structure with irregularly distributed rounded porosities with diameters reaching up to 500 µm. These characteristics have also been tested on determined Palaeolithic fragments, as diagenetic changes during burial have to be considered and may lead to the modification of the parameters established on the basis of modern bone references. In general, the chemical composition of bone objects can change drastically over time while micromorphological features, as evidenced by microCT, seem to be less susceptible to such alterations. In addition, microCT enables the comparison of inner and possibly less altered parts of the objects, and can be considered as completely non-destructive for small mineralised prehistoric objects. In this study, specific morphological features allowing the distinction of ivory and of whale bone from other bone and antler material were determined, even for altered materials dating back to Palaeolithic periods. Thus, we provide, in addition to archaeozoological, chemical and isotopic markers, a new non-destructive tool to identify some raw materials used for the fabrication of osseous objects ranging from recent to prehistoric periods. PY - 2011 DO - https://doi.org/10.1039/c0ja00246a SN - 0267-9477 SN - 1364-5544 VL - 26 IS - 9 SP - 1802 EP - 1812 PB - Royal Society of Chemistry CY - London AN - OPUS4-24338 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Michaeli, W. A1 - Baranowski, T. A1 - Kalinka, Gerhard T1 - Einfluss der Mikrostruktur auf den Druck- und Zug-E-Modul teilkristalliner Kunststoffe N2 - In Kooperation zwischen dem Institut für Kunststoffverarbeitung (IKV) und der Bundesanstalt für Materialforschung und -prüfung (BAM) wurde das mechanische Verhalten unter Druck- und Zugbelastung unterschiedlicher morphologischer Strukturen teilkristalliner Thermoplaste (PP und POM) untersucht. Im Ergebnis steigt der E-Modul sowohl der druck- wie auch zugbelasteten Prüfkörper aus spritzgegossenem PP und POM mit gröberem Gefüge an. Probekörper mit scherinduziertem Gefüge zeigen einen hohen Einfluss des Kristallisationsgrads auf den E-Modul. KW - Carbon fibre KW - Nanotubes KW - Hierarchical composites KW - Pull-out test KW - Push-out test PY - 2011 SN - 0025-5300 VL - 53 IS - 10 SP - 616 EP - 628 PB - Hanser CY - München AN - OPUS4-24341 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bastert, H. A1 - Dickhaut, D. A1 - Eßer, A. A1 - Hintzen, W. A1 - Hohberg, I. A1 - Kühne, Hans-Carsten A1 - Kühner, S. A1 - Meyer, L. A1 - Raupach, M. A1 - Westendarp, A. A1 - Wiens, U. T1 - Überarbeitung der DAfStb-Richtlinie Instandsetzung - Statusbericht N2 - Derzeit erfolgt in mehreren Arbeitsgruppen unter Einbindung interessierter Kreise die Überarbeitung der 2001 erschienenen Richtlinie 'Schutz und Instandsetzung von Betonbauteilen' (Instandsetzungsrichtlinie) des Deutschen Ausschusses für Stahlbeton e.V. (DAfStb). Hierüber wird in dem nachfolgenden Beitrag berichtet, um der Fachwelt frühzeitig darzustellen, in welche Richtung die Fortschreibung des Regelwerkes geplant ist. Die geplante neue Richtlinie wird nach derzeitigem Beratungsstand eine deutliche inhaltliche Erweiterung erfahren. Daher wird sie in 'Richtlinie für die Instandhaltung von Betonbauteilen' (Instandhaltungsrichtlinie) umbenannt und wird Festlegungen zu der grundsätzlichen Vorgehensweise bei der Instandhaltung unter Berücksichtigung der Komponenten Wartung, Inspektion, Instandsetzung und Verbesserung in Anlehnung an DIN 31051 enthalten. Da diese umfassenderen Aufgaben deutlich präziser beschrieben werden, konkretisieren sich auch die Anforderungen an die erforderliche Qualifikation des sachkundigen Planers, der zukünftig verstärkt die 'Restnutzungsdauer' bei seiner Planung beachten und in entsprechende Maßnahmen umsetzen muss. Mit den Ergänzungen und Änderungen wird die Richtlinie an die aktuellen Entwicklungen und Regelungen im Betonbau angepasst. Gleichzeitig gewinnt die Planungsleistung erheblich an Bedeutung. Für Instandsetzungsprodukte gemäß DIN EN 1504 werden, die Beseitigung derzeit noch enthaltener Unklarheiten und technischer Defizite auf europäischer Ebene vorausgesetzt, Verwendbarkeitsmöglichkeiten aufgezeigt. Die Ausführung von Instandhaltungsmaßnahmen wird durch die Einführung von Überwachungsklassen mit zugehörigen Anforderungen an die durchzuführenden Prüfungen spezifiziert und damit konkretisiert. KW - Betoninstandsetzung KW - DIN EN 1504 KW - Europäische Normungsarbeit KW - Instandsetzungsmörtel KW - Oberflächenschutzsysteme PY - 2011 DO - https://doi.org/10.1002/best.201008258 SN - 0005-9900 SN - 1437-1006 VL - 106 IS - 7 SP - 501 EP - 510 PB - Ernst CY - Berlin AN - OPUS4-24342 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Liehr, Sascha ED - Mukhopadhyay, S.C. T1 - Polymer optical fiber sensors in structural health monitoring N2 - This chapter summarizes the recent development in the relatively new and emerging field of structural health monitoring using polymer optical fiber (POF) sensors, also referred to as plastic optical fiber sensors. The extraordinary mechanical properties of POF in terms of strainability and ruggedness allows for measurement applications that could not or only insufficiently be solved with existing techniques. A great number of measurement parameters relevant for structural health monitoring applications, such as strain, displacement, crack width, vibrations or moisture can be measured with POF sensors. Numerous sensing principles have been proposed during the last 20 years and the most promising techniques and developments for SHM will be introduced. The focus is on the measurement of physical quantities for early damage detection and propagation, structural surveillance and analysis of dynamic processes. PY - 2011 SN - 978-3-642-21098-3 DO - https://doi.org/10.1007/978-3-642-21099-0 SN - 1876-1100 N1 - Serientitel: Lecture Notes in Electrical Engineering – Series title: Lecture Notes in Electrical Engineering VL - 96 SP - 297 EP - 333 PB - Springer CY - Berlin, Heidelberg AN - OPUS4-24343 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Niebergall, Ute T1 - Comparison of the material parameters of polyethylene grades with the test performance behaviour of packagings for the transport of dangerous goods in dependence on the pre-storage time with 55% nitric acid N2 - The material parameters melt flow rate MFR, density D, notched impact strength N.I.S. at -30 °C, stress crack resistance FNCT and resistance to oxidative degradation Ox (determined by the increase of MFR) have been selected for a comparison of polyethylene grades for one design type in the “European Standard EN 15507 - Transport packaging for dangerous goods - Comparative material testing of polyethylene grades”. The parameters have a systematic relationship with design type tests. The notched impact strength at -30 °C and the resistance to oxidative degradation of polyethylene grades determined with test specimens of compression moulded sheets are directly comparable with drop tests at -18 °C of design types produced of these grades after pre-storage with 55 % nitric acid for 21 days at 40 °C. The impact of the pre-storage time of jerricans with 55 % nitric acid at 40 °C and 23 °C on the marginal drop heights in drop tests at -18 °C, on the MFR and on the tensile properties tensile strength, breaking elongation and the elastic modulus were investigated. Packaging design types (jerricans) made of three polyethylene grades from different producers were pre-stored with 55 % nitric acid for 21,42 and 84 days at 40 °C as well as for six months at 23 °C. The MFR and tensile properties of test specimens taken from the design type side walls as well as the marginal drop heights of the jerricans in drop tests at -18 °C were determined. The values of the notched impact strength at -30 °C of polyethylene grades are not comparable with the marginal drop heights determined in drop tests at -18 °C. The oxidative damaging impact of nitric acid has a greater effect on the grade with lower resistance to oxidative degradation by reducing more significantly the marginal drop heights with increasing pre-storage time. Pre-damage with 55 % nitric acid for 21 days at 40 °C, as recommended in ISO 16101 and EN 15507 caused an increase in the marginal drop heights of most design types in drop tests when compared with design types without pre-damage. The test results demonstrated clearly that pre-storage of the jerricans for six months at 23 °C caused a higher increase in the MFR and lower marginal drop heights of the jerricans in drop tests at -18 °C compared with pre-storage of the jerricans for 21 days at40 °C. The mechanical properties change as a result of diffusion of nitric acid into the polyethylene grades and the reaction of the nitric acid with the polymers. The percentage decrease and increase in the tensile strength, breaking elongation and elasticity modulus of test specimens taken from the design type side walls after different pre-storage times were only partly comparable with the marginal drop heights in drop tests at -18 °C. T2 - EUROCORR 2011 - Developing solutions for the global challenge CY - Stockholm, Sweden DA - 04.09.2011. KW - Gefahrgutverpackungen KW - Polyethylenformstoffe KW - Baumusterprüfungen KW - Nachweis der chemischen Verträglichkeit KW - Oxidativer Abbau PY - 2011 SP - 1 EP - 12 AN - OPUS4-24346 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liehr, Sascha A1 - Krebber, Katerina ED - De Roeck, G. ED - Degrande, G. ED - Lombaert, G. ED - Müller, G. T1 - A novel quasi-distributed long-gauge fiber optic strain sensor system for dynamic measurement N2 - We present a novel technique based on incoherent optical frequency domain reflectometry (OFDR) to measure length changes quasi-distributed between reflection points in optical fibres. The technique enables length changes to be measured with a resolution better than 1 µm and allows for static and dynamic measurement capabilities up to 2 kHz. We demonstrate that dynamic measurements of multiple fibre sections can be conducted independently from each other with high precision. Due to the precise and dynamic measurement capabilities, the proposed sensor system is expected to open new fields of application, especially in the structural-health-monitoring sector. Possible applications are discussed in the paper. T2 - EURODYN 2011 - 8th International conference on structural dynamics CY - Leuven, Belgium DA - 04.07.2011 KW - Distributed sensor KW - Strain sensor KW - Optical fiber sensor KW - Structural health monitoring KW - OFDR KW - Length change measurement KW - Dynamic sensor PY - 2011 SN - 978-90-760-1931-4 SP - 2097 EP - 2102 AN - OPUS4-24347 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wendt, Mario A1 - Lenke, Philipp A1 - Krebber, Katerina A1 - Glötzl, R. T1 - POF Based Fiber Optic Inclinometer T2 - POF 2011 - The 20th International Conference on Plastic Optical Fibers CY - Bilbao, Spain DA - 2011-09-14 PY - 2011 AN - OPUS4-24598 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija A1 - Müller, Christina A1 - Manzey, D. T1 - Human Redundancy in Non-Destructive Testing: The Effect of Social Loafing within the 4-Eye Priciple in Nuclear Waste Management T2 - EAWOP (European Association of Work and Organizational Psycholgie) CY - Maastricht, Netherlands DA - 2011-06-25 PY - 2011 AN - OPUS4-24599 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Simone A1 - Werrel, Martin A1 - Deubel, Jan T1 - Vitiated Cone Calorimeter-Experience and Characteristics T2 - Symposium on Cone Calorimeter, ISO meeting TC 92 SC3/SC4 Fire threat to people and environment CY - Ottawa, Canada DA - 2011-10-17 PY - 2011 AN - OPUS4-24600 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hothan, Sascha A1 - Ehlig, D. T1 - Hochtemperaturverhalten von Stahlbetonplatten mit Textilbetonverstärkung T2 - Telxtilbeton in Theorie und Praxis, Tagungsband zum 6. Kolloquium zu Textilbewhrten Tragwerken, DFG CY - Berlin, Germany DA - 2011-09-19 PY - 2011 AN - OPUS4-24602 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pittner, Andreas A1 - Weiß, D. A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - Fast temperature field generation for welding simulation and reduction of experimental effort N2 - The quality of welding processes is governed by the occurring induced distortions yielding an increase in production costs due to necessary reworking. Especially for more complex specimens, it is difficult to evaluate the optimal configuration of welding sequences in order to minimize the distortion. Even experienced welding operators can solve this task only by trial and error which is time and cost consuming. In modern engineering the application of welding simulation is already known to be able to analyse the heat effects of welding virtually. However, the welding process is governed by complex physical interactions. Thus, recent weld thermal models are based on many simplifications. The state of the art is to apply numerical methods in order to solve the transient heat conduction equation. Therefore, it is not possible to use the real process parameters as input for the mathematical model. The model parameters which allow calculating a temperature field that is in best agreement with the experiments cannot be defined directly but inversely by multiple simulations runs. In case of numerical simulation software based on finite discretization schemes this approach is very time consuming and requires expert users. The weld thermal model contains an initial weakness which has to be adapted by finding an optimal set of model parameters. This process of calibration is often done against few experiments. The range of model validity is limited. An extension can be obtained by performing a calibration against multiple experiments. The focus of the paper is to show a combined modelling technique which provides an efficient solution of the inverse heat conduction problem mentioned above. On the one hand the inverse problem is solved by application of fast weld thermal models which are closed form solutions of the heat conduction equation. In addition, a global optimization algorithm allows an automated calibration of the weld thermal model. This technique is able to provide a temperature field automatically that fits the experimental one with high accuracy within minutes on ordinary office computers. This fast paradigm permits confirming the application of welding simulation in an industrial environment as automotive industry. On the other hand, the initial model weakness is compensated by calibrating the model against multiple experiments. The unknown relationship between model and process parameters is approximated by a neural network. The validity of the model is increased successively and enables to decrease experimental effort, For a test case, it is shown that this approach yields accurate temperature fields within very short amount of time for unknown process parameters as input data to the model contributing to the requirement to construct a substitute system of the real welding process. KW - Heat flow KW - Neural networks KW - Simulating KW - Temperature KW - Welding PY - 2011 SN - 0043-2288 SN - 1878-6669 VL - 55 IS - 09-10 SP - 83 EP - 90 PB - Springer CY - Oxford AN - OPUS4-24603 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kromm, Arne A1 - Brauser, Stephan A1 - Kannengießer, Thomas A1 - Rethmeier, Michael T1 - High-energy synchrotron diffraction study of a transformation induced plasticity steel during tensile deformation N2 - Energy-dispersive x-ray diffraction offers the possibility for measurement and evaluation of diffraction spectra containing information of various diffraction lines of all contributing crystalline phases of a material. Combined strain imaging and diffraction analysis was conducted during the tensile test of a low alloyed transformation-induced plasticity (TRIP) steel in order to investigate the transformation induced plasticity, strain hardening, and load partitioning effects. Optical strain imaging allowed for determination of localized true strains from three-dimensional deformations measured in situ. High-energy synchrotron radiation has permitted diffraction analysis in transmission mode to gather information from the material interior. Phase-specific stress evolution during loading could be observed applying the sin2ψ technique during certain load steps. The strains of the individual lattice planes were determined in different locations under varying angles between loading and perpendicular direction. Using energy-dispersive methods it was also possible to determine the transformation behaviour during elastic and plastic regime taking into account a large number of diffraction lines. The results show that the approach practised here enables one to pull together macroscopic and phase-specific microscopic material behaviour in order to improve existing models for prediction of complex load situations. KW - EDXRD KW - Transformation-induced plasticity (TRIP) KW - Residual stress KW - Synchrotron KW - Martensite transformation PY - 2011 DO - https://doi.org/10.1177/0309324711403969 SN - 0309-3247 SN - 2041-3130 VL - 46 IS - 7 SP - 581 EP - 591 PB - Sage CY - London AN - OPUS4-24604 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pötzsch, Klaus-Michael A1 - Krischok, Frank T1 - Genf und die Fortentwicklung desADN T2 - 22. Internationale Binnenschifffahrtsgefahrguttage CY - Mannheim, Germany DA - 2011-10-25 PY - 2011 AN - OPUS4-24605 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Werner, Jan T1 - ISO-Container CSC T2 - ERFA Tanks, BK-Schüttgut-Container und MEMU, BAM CY - Berlin, Germany DA - 2011-10-20 PY - 2011 AN - OPUS4-24606 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Tang, Z. A1 - Schempp, Philipp A1 - Seefeld, T. A1 - Schwenk, Christopher A1 - Vollertsen, F. T1 - Kornfeinung beim WIG- und Laserstrahlschweißen von Aluminiumlegierungen N2 - Die Kornfeinung beim Schweißen ist mit einem Übergang von groben, stängeligen Körnern zu kleineren, globulitischen Körnern im Schweißgut verbunden. Die Feinung der Korngröße und Form führt sowohl zu einer wesentlichen Verbesserung der Schweißeignung als auch zu verbesserten mechanischen Eigenschaften. Heute gebräuchliche Schweißzusatzwerkstoffe enthalten zum Teil bereits geringe Mengen kornfeinender Zusätze, deren Wirksamkeit jedoch von einer Reihe weiterer Randbedingungen abhängt. Durch Zugabe definierter Mengen an Keimbildnern (AlTi5B1) in das Schmelzbad wurde die Abhängigkeit der Korn-größe und –form vom Titan/Bor-Gehalt untersucht. Weiterhin wurde der zur vollständigen Kornfeinung notwendige Mindestgehalt an Keimbildner für unterschiedliche Legierungen und unter unterschiedlichen Schweißbedingungen, sowohl beim WIG-Schweißen als auch beim Laserstrahlschweißen bestimmt. Die Ergebnisse zeigen, dass sich die Korngröße im Schweißgut bis auf ein Minimum von ca. 20µm verringern lässt und zugleich der Anteil der globulitischen Körner zunimmt. Der Mindestgehalt an Keimbildner für vollständige Korn-feinung hängt stark von Schweißgeschwindigkeit und Legierungszusammensetzung ab. Der Einfluss der Kornfeinung auf die Festigkeit, Duktilität sowie die Heißrissempfindlichkeit der Schweißverbindungen wird an ausgewählten Bespielen aufgezeigt. T2 - DVS Congress 2011 - Große Schweißtechnische Tagung CY - Hamburg, Deutschland DA - 27.09.2011 KW - Kornfeinung KW - WIG-Schweißen KW - Laserstrahlschweißen KW - Aluminium PY - 2011 SN - 978-3-87155-267-0 VL - 275 SP - 153 EP - 160 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-24607 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wolf, S. E. A1 - Leiterer, Jork A1 - Pipich, V. A1 - Barrea, R. A1 - Emmerling, Franziska A1 - Tremel, W. T1 - Strong stabilization of amorphous calcium carbonate emulsion by ovalbumin: gaining insight into the mechanism of "polymer-induced liquid precursor" processes N2 - The impact of the ovo proteins ovalbumin and lysozyme—present in the first stage of egg shell formation—on the homogeneous formation of the liquid amorphous calcium carbonate (LACC) precursor, was studied by a combination of complementing methods: in situ WAXS, SANS, XANES, TEM, and immunogold labeling. Lysozyme (pI = 9.3) destabilizes the LACC emulsion whereas the glycoprotein ovalbumin (pI = 4.7) extends the lifespan of the emulsified state remarkably. In the light of the presented data: (a) Ovalbumin is shown to behave commensurable to the 'polymer-induced liquid precursor' (PILP) process proposed by Gower et al. Ovalbumin can be assumed to take a key role during eggshell formation where it serves as an effective stabilization agent for transient precursors and prevents undirected mineralization of the eggshell. (b) It is further shown that the emulsified LACC carries a negative surface charge and is electrostatically stabilized. (c) We propose that the liquid amorphous calcium carbonate is affected by polymers by depletion stabilization and de-emulsification rather than 'induced' by acidic proteins and polymers during a so-called polymer-induced liquid-precursor process. The original PILP coating effect, first reported by Gower et al., appears to be a result of a de-emulsification process of a stabilized LACC phase. The behavior of the liquid amorphous carbonate phase and the polymer-induced liquid-precursor phase itself can be well described by colloid chemical terms: electrostatic and depletion stabilization and de-emulsification by depletion destabilization. KW - Biomineralisation KW - Calcium carbonate KW - PILP KW - LACC PY - 2011 DO - https://doi.org/10.1021/ja202622g SN - 0002-7863 SN - 1520-5126 VL - 133 IS - 32 SP - 12642 EP - 12649 PB - American Chemical Society CY - Washington, DC AN - OPUS4-24628 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kreft, B. A1 - Bednarczyk, M. A1 - Emmerling, Franziska A1 - Marsch, W.C. T1 - Cutaneous-subcutaneous pseudolymphoma after specific immunotherapy with grass-rye pollen-allergen extract containing aluminium hydroxide N2 - Allergen-specific immunotherapy is an important treatment procedure in IgE-mediated allergic diseases such as allergic rhinitis or insect toxin allergies. A reduction in the clinical reaction to the allergens to which the patient is known to be sensitized is intended by means of antigen-specific influence on the immune system. The allergenspecific immunotherapy can be applied by subcutaneous injections, and for selected allergens by means of sublingual application of the appropriate allergen. Occasionally, the injection of aluminium hydroxide-adsorbed sera induces a usually transient formation of granulomas. We are reporting on a rare case of cutaneous-subcutaneous pseudolymphoma in the injection area of both upper arms, probably induced by subcutaneous allergen-specific immunotherapy. KW - Allergen-specific immunotherapy KW - Pseudolymphoma KW - Aluminium hydroxide PY - 2011 SN - 1642-395X VL - XXVIII IS - 2 SP - 134 EP - 137 PB - Termedia Wydawnictwa Med. CY - Pozna´n AN - OPUS4-24629 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bartscher, M. A1 - Ehrig, Karsten A1 - Staude, Andreas A1 - Goebbels, Jürgen A1 - Neuschaefer-Rube, U. T1 - Application of an Industrial CT Reference Standard for Cast Freeform Shaped Workpieces T2 - International Symposium on Digital Industrial Radiology and Computed Tomography (DIR2011), 20.-22.6.2011 in Berlin CY - Berlin, Germany DA - 2011-06-20 PY - 2011 AN - OPUS4-24630 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kranzmann, Axel A1 - Bettge, Dirk A1 - Ruhl, Aki Sebastian A1 - Bohraus, Stefan T1 - Transport von CO2 in Pipelines - Anforderungen an das CO2 in Rauchgasen T2 - DBI-Fachforum CO2 - Carbon Capture and Storage CY - Berlin, Germany DA - 2011-05-10 PY - 2011 AN - OPUS4-24634 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hothan, Sascha A1 - Ehlig, D. ED - Ortlepp, R. ED - Curbach, M. T1 - Hochtemperaturverhalten von Stahlbetonplatten mit Textilbetonverstärkung N2 - Die Verwendung von Endlosfilamenten aus Carbon als Be-wehrungsmaterial für Beton, sogenannter Textilbeton, bietet die Möglichkeit der Sanierung und der Verstärkung bestehender Stahlbetonkonstruktionen. Dabei muss die Frage nach dem Feuerwiderstand von derart verstärkten Tragwerken be-antwortet werden. Aufschluss darüber liefern Brandversuche. Mit Textilbeton verstärkte Stahlbetonplatten haben in Brandversuchen nach der Einheits-Temperaturzeitkurve bei 33 % der Traglast mehr als 60 Minuten standgehalten. Bei 50 % der Traglast kam es nach einer Branddauer von 55 Minuten, bei 65 % nach 30 Minuten, zu einem Zugversagen der textilen Verstärkungsschicht. Bei während des Brandes unbelasteten bzw. gering belasteten Platten lagen die im Anschluss ermittelten Resttragfähigkeiten bei 65 % der Bruchlast nach 30 Minu-ten Branddauer bzw. bei 50 % der Bruchlast nach 60 Minuten Branddauer. Wäh-rend und nach der Beflammung waren zunehmende Durchbiegungen und Rissbreiten erkennbar. Es traten aber keine Abplatzungen auf, weshalb die Ver-stärkungsschicht aus Textilbeton als zusätzliche Betondeckung für die Stahlbe-wehrung angerechnet werden kann. Diese außerordentlich positiven Ergebnisse zeigen, dass für verstärkte Konstruktionen Feuerwiderstandsklassen von F60 bzw. R60 ohne zusätzliche Maßnahmen erreicht werden können. Dies ist von ho-her Relevanz für die wirtschaftliche Anwendung dieser Verstärkungsmethode. Für ein umfassendes Verständnis der Interaktion zwischen den Bewehrungen Textil und Stahl sowie der Versagensmechanismen während des Brandes, sind weitere Erkenntnisse über die mechanischen Eigenschaften von Textilbeton im Hochtemperaturbereich nötig. Auch der Einfluss der Oxidation des Carbons konnte nicht abschließend beurteilt werden. 354 HOTHAN und EHLIG: Hochtemperaturverhalten von Stahlbetonplatten mit TRC-Verstärkung Summary: Using endless carbon filaments for concrete reinforcement, so called textile reinforced concrete, the possibility of reconstruction and strengthening of existing concrete structures arises. The question concerning fire resistance of structures strengthened like this has to be answered. Fire tests provide answers. Steel reinforced concrete slabs strengthened with textile reinforced concrete load-ed with 33 % of ultimate load survived an ISO-fire for 60 minutes. Loaded with 50 % and 65 % of ultimate load the slabs failed after 55 minutes and 30 minutes of fire exposure due to tension failure of the textile reinforcement layer. Slabs not loaded or with a low load level during fire exposure showed remaining bearing resistances of 65 % of ultimate load after 30 minutes and 50 % of ultimate load after 60 minutes of fire exposure. During and after fire exposure rising deflec-tions and growing crack widths were observed. However no spalling occurred. Therefore the textile reinforced concrete layer can be taken into account as con-crete covering for the steel reinforcement. Those extraordinary positive results document, that reinforced concrete structures with additional fibre reinforced concrete can achieve fire resistance classes of R60 without additional provisions. To achieve comprehensive understanding of interaction between steel and fibre reinforcement and failure mechanisms in case of fire more knowledge concerning the mechanic properties of fibre reinforced concrete at high temperatures is es-sential. The influence of oxidation of the carbon fibres could not fully be an-swered. T2 - 6. Kolloquium zu textilbewehrten Tragwerken (CTRS6) CY - Berlin, Germany DA - 19.09.2011 KW - Feuerwiderstand KW - Abplatzen KW - Textilbeton KW - Brandbeanspruchung KW - Biegebelastung PY - 2011 SN - 978-3-86780-245-1 SP - 353 EP - 367 AN - OPUS4-24635 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ehlig, D. A1 - Hothan, Sascha ED - Koenders, E.A.B. ED - Dehn, F. T1 - Reinforced concrete slabs strengthened with textile reinforced concrete subjected to fire N2 - Thin layers of textile reinforced concrete (TRC) can be used as strengthening for reinforced concrete (RC) slabs or beams to increase their foad-bearing capacity. The concrete matrix consists of a fine-grained concrete with a thickness of 8 to 15 mm. Information on the behaviour of strengthened structures subjected to fire is of particular inlerest for practical applications of this innovative construction method. A total of 7 RC slabs with Steel reinforcement were produced: 2 slabs were used as reference and 5 slabs were strengthened with three layers of textile reinforcement. Ultimate capacity of reference slabs and particular TRC strengthened slabs was determined from statie load results fom 4-point-bending tests. Fire tests on these slabs were carried out with utilization fectors using a Standard temperature curve (ISO-834-1) for fire testing. Test loads varied between 0 % and 65 % ofuMmate load. To detect temperatures during fire exposure thermocouples were arranged throughout the cross-section of the slabs. Depending on the utilization the slabs were exposed to fire for 30 minutes or for 60 minutes. In some cases bending fäilure occurred, in other cases the slabs survived. None of the specimens exhibited any visual damage or concrete spalling during fire exposure. Results of deformation measurements and residual strength measurements are presented. Even though mechanisms are not fifily understood, it is important to discuss the presumable reasons for the surprisingiy positive test results. It is presumed tbat the key mechanisms contributing to the outstanding fire resistance capability presented are: superior crack control of the TRC and load redistribution between textile and Steel reinforcement as well as the primary load transfer directly into the slabs. T2 - 2nd International RILEM workshop on concrete spalling due to fire exposure CY - Delft, The Netherlands DA - 05.10.2011 KW - Textile reinforced concrete KW - Fine-grained concrete KW - Carbon fibres KW - Bending load KW - Fire exposure PY - 2011 SN - 978-2-35158-118-6 VL - PRO 80 SP - 419 EP - 426 PB - RILEM Publications AN - OPUS4-24636 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Reimund, Verena A1 - Blome, Mark A1 - Pelkner, Matthias A1 - Kreutzbruck, Marc T1 - Fast defect parameter estimation based on magnetic flux leakage measurements with GMR sensors N2 - We present a fast inverse scheme that is capable of simultaneously estimating the parameters depth, opening and length for rectangular 3D geometries of surface-breaking defects. The parameter estimation is realized by an iterative least-squares minimization using the trust-region reflective algorithm. A semi-analytic magnetic dipole model that allows the sensor characteristics to be incorporated is used for predicting the stray magnetic fields. Giant magneto-resistance (GMR) measurements were carried out on a test specimen that includes a series of artificial defects. For the estimation of the defect depths relative errors between 0.6% and 15.9% have been obtained. Due to its very low computational costs, the inverse scheme can suitably be employed in automated production environments. KW - Magnetic flux leakage KW - GMR sensor KW - Nonlinear least-squares optimization PY - 2011 DO - https://doi.org/10.3233/JAE-2011-1391 SN - 1383-5416 SN - 0925-2096 VL - 37 IS - 2-3 SP - 199 EP - 205 PB - IOS Press CY - Amsterdam, The Netherlands AN - OPUS4-24637 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wallstabe, Ronald T1 - On the tribological behaviour of SiC and alumina mated against different steels under dry sliding conditions N2 - There have been several studies regarding the tribological behaviour of ceramics such as SiC and alumina mated against steels or self-mated. Nevertheless, only Little is known about possible tribochemical reactions when ceramics are mated against steels. In the present study, ceramic pins made of SiC (EKasicF) or alumina (F99.7) respectively were tested under dry sliding conditions against different steel disc counter bodies using a pin-ondisc tribometer. The different ceramics showed significant differences in their tribological behaviour, i.e., coefficient of friction and wear amount. Especially, the SiC couples showed significant differences in the wear amounts while these were quite similar for the alumina couples. The wear behaviour of the SiC couples is discussed in more detail. A correlation between chromium content of the steel discs was found for the SiC couples. The surfaces of selected specimens were analysed by Auger-Electron-Spectroscopy (AES). Wear for the SiC couples was mainly attributed to tribochemical reactions as far as the steel disc was containing the alloying element chromium in considerable amount. Furthermore, a simple wear schematic is proposed. KW - Unlubricated friction KW - Clutches KW - Ceramic KW - composite KW - Ceramics KW - Chromium KW - AES (auger) KW - Unlubricated wear KW - Wear mechanisms PY - 2011 DO - https://doi.org/10.1007/s11249-011-9843-1 SN - 1023-8883 SN - 1573-2711 VL - 44 IS - 2 SP - 247 EP - 257 PB - Springer Science Business Media B.V. CY - Dordrecht AN - OPUS4-24608 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wäsche, Rolf A1 - Cruzado, Aitor A1 - Hartelt, Manfred A1 - Urchegui, M.A. A1 - Gomez, X. T1 - Oxidative wear in gross slip fretting of thin steel wires T2 - ITC Hiroshima Satellite Symposium, Tribochemistry Hagi 2011 CY - Hagi, Japan DA - 2011-10-25 PY - 2011 AN - OPUS4-24609 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wäsche, Rolf A1 - Woydt, Mathias T1 - The history of the Stribeck curve and the role of Adolf Martens T2 - Int. Tribology Congress / ITC Hiroshima CY - Hiroshima, Japan DA - 2011-10-30 PY - 2011 AN - OPUS4-24610 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scholz, Christian A1 - Spaltmann, Dirk A1 - Woydt, Mathias T1 - Höchstbelastbare Wälzkontakte mit geringer Misch-/Grenzreibungszahl N2 - Leichtbaustrategien im Antriebsstrang erhöhen durch Downsizing die Hertz’schen Kontaktpressungen und die mechanischen Lasten. Dadurch müssen neben wälzbeständigen Stählen auch dazu passende reibungsmindernde Konzepte gefunden werden, in der vorliegenden Arbeit wurden alternative, hoch zähe Stähle mit einer Wälzbeständigkeit bis Pomax = 4,2 GPa untersucht, welche mit geeigneten Grundöl- und Additivkombinationen die Reibungszahlen herunter auf 0,025 reduzieren konnten. Diese alternativen Stahllegierungen erlauben nicht nur an der Zahnflanke sehr hohe Kontaktpressungen, sie bieten außerdem entsprechende Zähigkeits- und Festigkeitseigenschaften für den Zahnfuß. In vorangegangenen Untersuchungen wurde eine Vielzahl verschiedener Dünnschichten auf ihre Überrollbeständigkeit unter Extrembeanspruchungen validiert. Allerdings zeigte sich bei den meisten Dünnschichten ein Qualitätsunterschied von Charge zu Charge. Unter Verwendung verschiedener organischer, metallorganischer und anorganischer Additive konnten, sich daran anschließende Versuche, vielversprechende Ergebnisse erzielt werden. Sämtliche Versuche unter extremen Beanspruchungen wurden bei +120°C Öltemperatur auf Zwei-Scheiben-Tribometern vom Typ AMSLER und 2Disk von Optimol Instruments unter Misch-/Grenzreibungsbedingungen durchgeführt und die tribologischen Eigenschaften der neuartigen, unbeschichteten Stähle und in Relation zu leistungsstarken DLC-/ZrCN Dünnschichten gesetzt. T2 - 52. Tribologie-Fachtagung - Reibung, Schmierung und Verschleiß - Forschung und praktische Anwendungen CY - Göttingen, Deutschland DA - 26.09.2011 KW - Hochzähe Stähle KW - DLC KW - ZrCN KW - Dünnschichten KW - Extrembeanspruchung KW - Polyglykole KW - Additive PY - 2011 SN - 978-3-00-035439-7 VL - I SP - 11/1 EP - 11/16 AN - OPUS4-24611 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vila-Comamala, J. A1 - Diaz, A. A1 - Guizar-Sicairos, M. A1 - Gorelick, S. A1 - Guzenko, V.A. A1 - Karvinen, P. A1 - Kewish, C.M. A1 - Färm, E. A1 - Ritala, M. A1 - Mantion, Alexandre A1 - Bunk, O. A1 - Menzel, A. A1 - David, C. ED - Morawe, C. ED - Khounsary, A.M. ED - Goto, S. T1 - Characterization of a 20-nm hard X-ray focus by ptychographic coherent diffractive imaging N2 - Recent advances in the fabrication of diffractive X-ray optics have boosted hard X-ray microscopy into spatial resolutions of 30 nm and below. Here, we demonstrate the fabrication of zone-doubled Fresnel zone plates for multi-keV photon energies (4-12 keV) with outermost zone widths down to 20 nm. However, the characterization of such elements is not straightforward using conventional methods such as knife edge scans on well-characterized test objects. To overcome this limitation, we have used ptychographic coherent diffractive imaging to characterize a 20 nm-wide X-ray focus produced by a zone-doubled Fresnel zone plate at a photon energy of 6.2 keV. An ordinary scanning transmission X-ray microscope was modified to acquire the ptychographic data from a strongly scattering test object. The ptychographic algorithms allowed for the reconstruction of the image of the test object as well as for the reconstruction of the focused hard X-ray beam waist, with high spatial resolution and dynamic range. This method yields a full description of the focusing performance of the Fresnel zone plate and we demonstrate the usefulness ptychographic coherent diffractive imaging for metrology and alignment of nanofocusing diffractive X-ray lenses. T2 - SPIE Optics and photonics CY - San Diego, USA DA - 20.08.2011 KW - X-ray imaging KW - Diffractive X-ray optics KW - Electron beam lithography KW - Ptychographic coherent diffractive imaging PY - 2011 DO - https://doi.org/10.1117/12.893235 SN - 0277-786X N1 - Serientitel: Proceedings of SPIE – Series title: Proceedings of SPIE VL - 8139 SP - 81390E-1 EP - 81390E-7 AN - OPUS4-24613 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nöther, Nils A1 - Krebber, Katerina A1 - Schneider-Gloetzl, J. T1 - An all-digital implementation of the Brillouin optical frequency domain analysis for long-range distributed strain and temperature monitoring T2 - 8th International Symposium on Field Measurements in GeoMechanics (FMGM) CY - Berlin, Germany DA - 2011-09-12 PY - 2011 AN - OPUS4-24614 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vila-Comamala, J. A1 - Diaz, A. A1 - Guizar-Sicairos, M. A1 - Mantion, Alexandre A1 - Kewish, C.M. A1 - Menzel, A. A1 - Bunk, O. A1 - David, C. T1 - Characterization of high-resolution diffractive X-ray optics by ptychographic coherent diffractive imaging N2 - We have employed ptychographic coherent diffractive imaging to completely characterize the focal spot wavefield and wavefront aberrations of a high-resolution diffractive X-ray lens. The ptychographic data from a strongly scattering object was acquired using the radiation cone emanating from a coherently illuminated Fresnel zone plate at a photon energy of 6.2 keV. Reconstructed images of the object were retrieved with a spatial resolution of 8 nm by combining the difference-map phase retrieval algorithm with a non-linear optimization refinement. By numerically propagating the reconstructed illumination function, we have obtained the X-ray wavefield profile of the 23 nm round focus of the Fresnel zone plate (outermost zone width, Δr = 20 nm) as well as the X-ray wavefront at the exit pupil of the lens. The measurements of the wavefront aberrations were repeatable to within a root mean square error of 0.006 waves, and we demonstrate that they can be related to manufacturing aspects of the diffractive optical element and to errors on the incident X-ray wavefront introduced by the upstream beamline optics. KW - Fourier zone plate KW - Coherent diffraction imaging KW - Ptychography PY - 2011 DO - https://doi.org/10.1364/OE.19.021333 SN - 1094-4087 VL - 19 IS - 22 SP - 21333 EP - 21344 PB - Optical Society of America CY - Washington, DC AN - OPUS4-24615 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Koch, Matthias A1 - Köppen, Robert A1 - Nehls, Irene T1 - Neue Mykotoxin-Referenzmaterialien - Qualitätssicherung in der Lebensmittelanalytik N2 - Die zuverlässige Überwachung geltender Mykotoxin-Grenzwerte ist elementarer Bestandteil von Lebensmittelsicherheit und Verbraucherschutz. Durch die zunehmende Bedeutung der Qualitätssicherung ist auch die Nachfrage an zertifizierten Referenzmaterialien (ZRM) in den letzten Jahren deutlich gestiegen. Dem steht derzeit jedoch nur eine sehr begrenzte Auswahl geeigneter ZRM gegenüber. KW - Zertifiziertes Referenzmaterial KW - ERM KW - Ochratoxin A KW - Deoxynivalenol KW - Nivalenol KW - Zearalenon KW - Kaffee KW - Wein KW - Weizen PY - 2011 SN - 0012-0413 SN - 1869-2214 IS - September SP - 434 EP - 448 PB - Wiss. Verl.-Ges. CY - Stuttgart AN - OPUS4-24616 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Bredow, Andrea A1 - Berger, Wolfgang A1 - Wessel-Bothe, Stefan A1 - Keller, T. T1 - Optimierung des Säulenperkolationsverfahrens durch Automatisierung N2 - Elutionstests im Labormaßstab werden zur Ermittlung der Freisetzung von Schadstoffen aus Böden oder mineralischen Abfällen für die Verwertung in technischen Erdbau-werken durchgeführt. Sie sollen die Feldbedingungen möglichst realitätsnah wider-spiegeln und auch die Beurteilung der Freisetzung von Schadstoffen über längere Zeiträume ermöglichen. Aus diesem Grunde werden im Entwurf der novellierten BBodSchV neue Verfahren zur Eluatgewinnung aus den genannten Materialien festgeschrieben. T2 - DBG-Jahrestagung, Kommission VI, 'Böden verstehen - Böden nutzen - Böden fit machen' CY - Berlin, Germany DA - 03.09.2011 KW - Schadstofffreisetzung KW - Säulenperkolation KW - Werkstoffauswahl KW - Elutionsverfahren PY - 2011 UR - http://eprints.dbges.de/565/1/Berichte_der_DBG_Kalbe_2753.pdf SP - 1 EP - 4 AN - OPUS4-24648 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Berger, Wolfgang A1 - Kalbe, Ute A1 - Krüger, Oliver A1 - Litzba, Andreas T1 - Vergleich der Ergebnisse von Übereinstimmungstests bei Säulen- und Schüttelversuchen N2 - In der Bundes-Bodenschutz- und Altlasten-verordnung (BBodSchV) und im Arbeits-entwurf der Novellierung ist für den Wirkungspfad Boden-Grundwasser eine Sickerwasserprognose vorgesehen, um die Gefahren, die von kontaminierten Stand-orten für das Schutzgut Grundwasser ausgehen, beurteilen zu können. Bei der Sickerwasserprognose kann u.a. auf der Grundlage von Materialuntersuchungen im Labor die Quellstärke kontaminierter Ma-terialen ermittelt werden, welche dann bei Transportmodellierungen Berücksichtigung findet. Der Entwurf der Novellierung der BBodSchV sieht für die Ermittlung der Quellstärke den Übereinstimmungstest des Säulenversuchs nach DIN 19528 bis zu einem Wasser/Feststoff - Verhältnis (W/F) von 2 l/kg für anorganische und organische Stoffe (PAK) oder den Schüttelversuch nach DIN 19529 für anorganische Stoffe und E DIN 19527 für organische Stoffe auch jeweils mit einem W/F von 2 l/kg vor. Die Zulassung beider Elutionsverfahren setzt die Gleichwertigkeit der Ergebnisse beider Verfahren voraus. Im Folgenden werden die Ergebnisse des Vergleichs der Auslaugung von polyzyklischen aromat-ischen Kohlenwasserstoffen (PAK) aus unterschiedlichen Böden mit Hilfe beider Elutionsverfahren vorgestellt. T2 - DBG-Jahrestagung, Kommission VI, 'Böden verstehen - Böden nutzen - Böden fit machen' CY - Berlin, Germany DA - 03.09.2011 KW - Elutionsverfahren KW - Übereinstimmungstest KW - Säulenverfahren KW - Schüttelverfahren KW - Kontaminierte Böden KW - Polyzyklische aromatische Kohlenwasserstoffe (PAK) PY - 2011 UR - http://eprints.dbges.de/551/1/Berichte_der_DBG_Berger3376.pdf SP - 1 EP - 2 AN - OPUS4-24649 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bartholmai, Matthias A1 - Neumann, Patrick P. T1 - Adaptive ortsaufgelöste Gaskonzentrationsmessung mit einer Mikrodrohne KW - Gasmessung KW - Gasemission KW - Emissionskontrolle KW - Windvektor KW - Mikrodrohne KW - Data-Mapping KW - Gas measurement KW - Gas emission KW - Emission control KW - Wind vector KW - Micro-drone KW - Data mapping PY - 2011 DO - https://doi.org/10.1524/teme.2011.0158 SN - 0340-837X SN - 0178-2312 SN - 0171-8096 VL - 78 IS - 10 SP - 470 EP - 478 PB - Oldenbourg CY - München AN - OPUS4-24652 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griepentrog, Michael T1 - Stand der Normung und Normungsbedarf im Bereich der Dünnschichttechnik T2 - INS-Tagung DLC und CVD-Diamant: Kohlenstoffschichten auf dem Weg zur nationalen und internationalen Normung CY - Braunschweig, Germany DA - 2011-10-26 PY - 2011 AN - OPUS4-24653 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schempp, Philipp A1 - Schwenk, Christopher A1 - Rethmeier, Michael A1 - Cross, C.E. T1 - Weld metal grain refinement of aluminium alloy 5083 through controlled additions of Ti and B N2 - Kornfeinung im Schweißgut kann die mechanischen Eigenschaften der Schweißnaht und die Schweißeignung des Grundwerkstoffs deutlich verbessern. Eine Möglichkeit korngefeintes Schweißgut zu erreichen, ist das Versetzen des Schmelzbades mit kornfeinenden Mitteln. In dieser Studie wird gezeigt wie Titan- und Borzusätze Korngröße und -struktur von WIG-Schweißnähten der Al-Legierung 5083 (Al Mg4,5Mn0,7) beeinflussen. Dazu wurden in einem Gießprozess stäbchenförmige Einlagen hergestellt, die aus Grundwerkstoff und definierten Zusätzen der Kornfeinungslegierung Al Ti5B1 bestanden. Sie wurden als Ersatz für einen Schweißzusatzwerkstoff in einer Nut im Grundwerkstoff untergebracht und im WIG-Verfahren überschweißt. Durch die Steigerung des Titan- und Borgehalts im Schweißgut konnte dessen mittlere Korngröße deutlich verringert werden. Außerdem wurde eine Änderung der Kornstruktur beobachtet. Die Ergebnisse können als Grundlage genutzt werden, um die empfohlene chemische Zusammensetzung von Schweißzusätzen für Lichtbogenschweißen von Aluminium anzupassen. KW - Aluminium-Legierung 5083 KW - Kornfeinung KW - WIG-Schweißen PY - 2011 DO - https://doi.org/10.3139/120.110265 SN - 0025-5300 VL - 53 IS - 10 SP - 604 EP - 609 PB - Hanser CY - München AN - OPUS4-24654 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Schukar, Vivien A1 - Kusche, Nadine T1 - Calibration facility for quality certification of surface-attached fiber optic and electrical strain sensors N2 - Strain measurement in structures witli the purpose of long-term structurai health inonitoring must provide reliable inforination about the structure’s behavior over the whole period of use. The user must be sure that installed sensors are validated and work to the utmost satisfactiou. For this purpose, sensor Systems are tested using special facilities. Bccause it is not easy to characterize the strain transfer quality from the host structure into surface-applied strain sensors, a unique testing facility has been developed. Originally developed for fiber Bragg grating based sensors, the KALFOS facility (= calibration of fiber optic sensors) can also be used for electrical strain sensors. Calibration ineasurements are referenced by unbinsed Digital Image Correlation (D1C) and Electronic Speckle Pattern Interferometer (ESPI) methods. The strain transfer behavior can experimentally be analyzed and investigated under combined thermal and mechanical loading conditions and allows revealing wealuiesses in couimonly used attachment methodologies. The deformation of all members (particularly the coating/substrate - adhesive combination) in the sensing area is physically independently gained and recorded. Results achievcd allow precise description of the strain transfer function, Validation of the longterm strain sensor characteristics, matching of specific measurement requirements with environmental conditions, and, moreover, the verification of Standards for use of strain sensors. T2 - IEEE Sensors 2011 conference CY - Limerick, Ireland DA - 28.10.2011 KW - Fibre optic sensors KW - Structural health monitoring KW - Validation KW - Strain sensor KW - Surface application reliability PY - 2011 SN - 978-1-4244-9288-6 DO - https://doi.org/10.1109/ICSENS.2011.6127253 SP - 1337 EP - 1340 AN - OPUS4-24655 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Schukar, Vivien A1 - Tkachenko, Viktoriya T1 - How do application-related issues influence the reliability of fiber optic strain measurements? N2 - Fibre optic strain sensors are increasingly used and sensor systems are provided with specifications. Even if the performance is well specified, the strain characteristics of the sensor, strain transfer factor, mechanical stability under thermal influences, the performance of applied strain sensors can seriously differ from virgin sensor's the performance. The contribution will focus on issues that can deteriorate the sensor function or reduce the reliability of measurement results. Aspects are considered how to come to reliable strain measurements and how to validate strain measurements of applied sensors. Related to this topic, European activities like the recently started European COST TD1001 action, called (OfSeSa) will be presented. T2 - IEEE Sensors 2011 conference CY - Limerick, Ireland DA - 28.11.2011 KW - Fibre optic sensors KW - Structural health monitoring KW - Validation KW - Strain sensor KW - Surface application reliability PY - 2011 SN - 978-1-4244-9288-6 SP - 947 EP - 950 AN - OPUS4-24656 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scholz, Christian A1 - Woydt, Mathias T1 - Highly concentrated and low friction slip-rolling contacts through thin film coatings and/or alternative steels? T2 - Int. Tribology Conf. (ITC 2011) CY - Hiroshima, Japan DA - 2011-10-30 PY - 2011 AN - OPUS4-24657 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baer, Wolfram A1 - Klingbeil, Dietmar T1 - Entwicklung einer Key Curve-Methode für Gusseisen mit Kugelgraphit bei dynamischer Beanspruchung T2 - 37. MPA-Seminar - Werkstoff- & Bauteilverhalten in der Energie- & Anlagentechnik CY - Stuttgart, Deutschland DA - 2011-10-06 KW - Dynamic fracture mechanics KW - Crack resistance curve KW - Single specimen technique KW - Key curve PY - 2011 SP - 35.1 EP - 35.19 AN - OPUS4-24618 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von der Ehe, Kerstin A1 - Jaunich, Matthias A1 - Wolff, Dietmar T1 - UHMW-PE - a shielding material with special properties influenced by radiation N2 - Ultra high molecular weight polyethylene (UHMW-PE) - due to its high hydrogen content - is used as neutron shielding material in casks for storage and transport of radioactive materials. Besides this, UHMW-PE - as a high-performance polymer - has been used for several years in medical technology due to its excellent slip and wear properties. Due to the special properties of UHMW-PE which result basically from its extreme chain lengths and its high degree of crystallinity, it is predestinated for the aforementioned applications. In both cases, irradiation and its impact on the molecular structure of polyethylene play an important role. In the first case, irradiation exists as a by-product of inserting the radioactive material in the cask. Hence PE has to withstand any type of degradation affecting safety relevant aspects to be applicable for long term radiation shielding purposes for instance over a period of 40 years. In the second case irradiation is applied deliberately for purposes such as sterilization and crosslinking, leading to partial improvement of the mechanical properties (e.g. fracture toughness, crack propagation resistance, wear resistance) and better Chemical stability. Specifically concerning their use in the field of medical technology, different types of UHMW-PE have been objects of numerous publications. It is generally accepted that two parallel and competitive processes, based on chain scission and reactions of Ccentered radicals and molecular fragments, occur in PE as a consequence of radiation: radical recombination accounts for crosslinking, together with some disproportionation, formation of low molecular weight fragments, and recrystallization. Furthermore, formation of oxygenated structures in the presence of traces of oxygen is an antagonist of the C-centered radicals. Radiation induced scission preferentially takes place in the amorphous phase and noncrystalline surface of the crystals. It is followed by folding of molecular fragments, crystallinity growth and increased perfection in the crystal lamellae [4, 5]. Chain scission results in shorter polymer molecules, fewer entanglements, and consequently, increased molecular mobility. The scope of our investigation comprises an estimation of the radiation and thermal impact on the molecular and supra molecular structure of the two types of PE used for neutron shielding cask components. A further point which is worth to explore is to what extent these changes are detectable by thermo-analytical (TA) methods, such as Differential Scanning Calorimetry (DSC), Thermo Mechanical Analysis (TMA), Dynamic Mechanical Analysis (DMA) and Thermogravimetry (TG). Additionally FT-IR and solubility measurements have been performed. In our studies we focused on the UHMW-PE material GUR 4120 which was y irradiated at RT and compared to the untreated material. T2 - Jahrestagung Kerntechnik 2011 CY - Berlin, Germany DA - 17.05.2011 PY - 2011 SP - 1 EP - 5 AN - OPUS4-24620 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häcker, Ralf A1 - Klinger, Christian A1 - Klingbeil, Dietmar A1 - Kahlcke, Ole A1 - Schriever, Sina A1 - Wossidlo, Peter T1 - Zwischen Zeitstand und Relaxation - Einfluss der Proben- und Prüfmaschinensteifigkeit auf die Lebensdauer unter konstanter Belastung N2 - Zur Abschätzung der Lebensdauer eines bei höherer Temperatur langzeitbelasteten Bauteils wurden Zeitstandversuche, Relaxationsversuche und weitere Versuche mit unterschiedlichen Umgebungssteifigkeiten durchgeführt. Die Zeitstandversuche, deren Versuchsführung eine unendlich niedrige Umgebungssteifigkeit simuliert, liefern geringere Lebensdauern (Bruchzeiten) im Vergleich zu Versuchen mit endlich hohen, technisch relevanten Steifigkeiten bei vergleichbarer Probensteifigkeit (Geometrie), wobei die Lebensdauern mit steigender Umgebungssteifigkeit zunehmen. Die längsten Lebensdauern zeigen Relaxationsversuche mit einer unendlich hohen Umgebungssteifigkeit aufgrund ihrer Versuchsregelung. Für die Übertragung der an Proben gewonnenen Ergebnisse auf das Bauteil wurde das Steifigkeitsverhältnis Z zwischen der Steifigkeit der 'Probe' und der der 'Umgebung' definiert und angewandt. Das Steifigkeitsverhältnis des kritischen Bereichs im Bauteil und das der Werkstoffprobe in der Prüfmaschine sollten möglichst ähnlich sein. Dann lassen sich bei der Übertragung auf das Bauteil realistisch höhere Lebensdauern abschätzen als nur mit Kenntnis der Ergebnisse der Zeitstandversuche. T2 - DVM-Tagung: Werkstoffprüfung 2011 CY - Berlin, Germany DA - 2011-12-01 PY - 2011 AN - OPUS4-24625 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ferrero, Fabio A1 - Kluge, Martin A1 - Schröder, Volkmar T1 - Numerical Analysis of the Effect of the Electrode Distance during the Determination of the Flammability Limits of Gases T2 - COMSOL Conference 2011 CY - Ludwigsburg, Germany DA - 2011-10-26 PY - 2011 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. AN - OPUS4-24626 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Belombe, M.M. A1 - Nenwa, J. A1 - Emmerling, Franziska T1 - Stacking structure of quinolinium hydrogensquarate N2 - A new proton-transfer organic salt, quinolinium hydrogensquarate (C13H9NO4), has been synthesized and fully characterized by single crystal x-ray diffraction. The salt crystallizes in the monoclinic space group P21/n with the parameters: a = 3.8290(12) Å, b = 20.960(6) Å, c = 13.802(4) Å, β = 95.452(5)°, V = 1102.7(6) Å3, Z = 4 formula units. The structure consists of uncommon supramolecular neutral dimers which pile up parallel to [100] forming infinite sheets. These centrosymmetric dimers are held together by lateral hydrogen-bonds whereby two neighboring coplanar hydrogensquarate anions act as a bridge between two terminal quinolinium cations and C-H...O bridgings interlink next neighboring sheets. The bulk structure of this salt is consolidated by weak π–π interactions within the sheets which are neatly ordered side-by-side relative to one another. KW - Quinolinium squarate KW - Supramolecular dimer KW - Crystal structure KW - Proton-transfer salt PY - 2011 SN - 0973-4945 VL - 8 IS - 2 SP - 603 EP - 608 CY - Tamil Nadu AN - OPUS4-24627 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scholz, Christian A1 - Spaltmann, Dirk A1 - Woydt, Mathias T1 - Highly concentrated and low friction slip-rolling contacts through thin film coatings and/or alternative steels? T2 - Friction, Wear and Wear Protection (DGM) CY - Karlsruhe, Germany DA - 2011-10-26 PY - 2011 AN - OPUS4-24658 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachsmuth, Janne T1 - Wellenform basierte Quellenlokalisierung im Vergleich zu konventionellen Methoden N2 - Für eine 10 mm dicke Stahlplatte kann ein Bandpass so gesetzt werden, dass alle vorhandenen Wellenmoden mit derselben Schallgeschwindigkeit eintreffen. Anhand von Ortungsabweichungen und Ortungsunsicherheitswerten kann gezeigt werden, dass im Vergleich zu herkömmlichen Methoden der Quellenortung die Ortungsgenauigkeit durch eine Frequenzfilterung verbessert werden kann. T2 - 18. Kolloquium Schallemission CY - Wetzlar, Deutschland DA - 27.10.2011 KW - Schallemissionsprüfung KW - Ermüdungsrisswachstum KW - Korrosion PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-246612 SN - 978-3-940283-37-5 SP - 1 EP - 6 PB - DGZfP-BB 131 AN - OPUS4-24661 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachsmuth, Janne A1 - Bohse, Jürgen T1 - Schallemissionsanalyse von Schadensmechanismen an Feinkornstahl N2 - In dieser Arbeit werden geschweißte Platten aus dem Feinkornstahl P460NL1 untersucht. Korrosion und Ermüdungsrisswachstum werden als Schadensmechanismen in das Material eingebracht und auf ihre Nachweisbarkeit in Plattenversuchen geprüft. Die Schallemissionssignale wurden nach primären und sekundären Quellmechanismen getrennt und ihr Einfluss auf die Gesamtemission analysiert. T2 - 18. Kolloquium Schallemission CY - Wetzlar, Deutschland DA - 2011-10-27 KW - Schallemissionsprüfung KW - Ermüdungsrisswachstum KW - Korrosion PY - 2011 SN - 978-3-940283-37-5 IS - DGZfP-BB 131 (Vortrag 10) SP - 1 EP - 9 AN - OPUS4-24662 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Krüger, Oliver A1 - Berger, Wolfgang A1 - Wachtendorf, Volker T1 - Umweltverträglichkeit von Sportböden auf Kunststoffbasis - Entwicklung von Prüfmethoden T2 - Forum Kunstrasen FSB 2011/IAKS-Kongress CY - Cologne, Germany DA - 2011-10-26 PY - 2011 AN - OPUS4-24663 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nöther, N. A1 - Krebber, Katerina A1 - Schneider-Glötzl, J. T1 - An all-digital implementation of the Brillouin optical frequency domain analysis for long-range distributed strain and temperature monitoring N2 - For long-range measurements in geotechnical and industrial applications, distributed optical fiber sensors have become a tool of increasing importance throughout the past decade. Classic deformation monitoring (performed by strain gauges etc.) and temperature monitoring (Pt100 and alike) deliver data from fixed, single spots of a structure; quasidistributed measurements (fiber bragg gratings) provide a Chain of discrete measurement points along a limited sensing length. In contrast, an opticai fiber connected to a device for distributed strain and temperature sensing (DTSS) will provide a continuous profile of strain and temperature - spatially resolved down to less than 1 m - over a ränge of several tens of kilometers. In DTSS measurements, the nonlinear opticai effect of stimulated Brillouin Scattering (SBS) is employed: two light waves with a stable, tunable frequency offset are injected into opposite ends of the sensing fiber, where they will form a beat pattem, at which parts of the light will be scattered. By matching the frequency offset of the light waves to the propagation of acoustic fluctuation in the opticai fiber, a power transfer from one light wave to the other can be measured; since the acoustic propagation directly shifts with train and temperature of the fiber, these two quantities can be measured by tuning the light waves’ frequency offset. T2 - 8th International symposium on field measurements in geomechanics - FMGM 2011 CY - Berlin, Germany DA - 12.09.2011 PY - 2011 SP - 1 EP - 6 AN - OPUS4-24664 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dabah, Eitan A1 - Kannengießer, Thomas A1 - Eliezer, D. A1 - Böllinghaus, Thomas T1 - Influence of hydrogen on the residual stresses in super martensitic stainless steel T2 - Sitzung des DVS Fachausschusses13 "Rapidtechnologien" CY - Munich, Germany DA - 2011-10-18 PY - 2011 AN - OPUS4-24665 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Portella, Pedro Dolabella A1 - Trappe, Volker A1 - Grasse, Fabian A1 - Thöns, Sebastian A1 - Said, Samir T1 - Structural Health Monitoring of Wind Turbine Blades T2 - MS&T, Invited paper, Prof. K. K. Chawla Honorary Symposium on Fibers, Foams and Composites: Science and Engineering CY - Columbus, OH, USA DA - 2011-10-19 PY - 2011 AN - OPUS4-24666 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schönhals, Andreas T1 - Dielectric Spectroscopy - Basics, Effects and Examples - T2 - Graduiertenkolleg "Analyse und Simulation elektrischer Wechselwirkungen zwischen Implantaten und Biosystemen", Universität Rostock CY - Rostock, Germany DA - 2011-10-20 PY - 2011 AN - OPUS4-24638 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schönhals, Andreas T1 - Polymer Based Nanocomposites - Interplay between Interfacial and Bulk Effects - T2 - Kolloquiumsvortrag am National Research Center Canada - Industrial Materials CY - Boucherville, Canada DA - 2011-09-30 PY - 2011 AN - OPUS4-24639 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schönhals, Andreas T1 - Molecular Dynamics in Nanometre Confinement T2 - Broadband Dielectric Spectroscopy and its Advanced Technological Applications CY - Perpignan, France DA - 2011-09-21 PY - 2011 AN - OPUS4-24640 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schönhals, Andreas T1 - Polymer based nanocomposites as investigated by dielectric spectroscopy T2 - Kolloquiumsvortrag am Materials Physics Center, San Sebastian CY - San Sebastián, Spain DA - 2011-06-02 PY - 2011 AN - OPUS4-24641 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schönhals, Andreas A1 - Frunza, S. A1 - Frunza, L. A1 - Ganea, P. A1 - Kosslick, H. A1 - Harloff, J. A1 - Schulz, A. T1 - Molecular relaxation processes in a MOF-5 structure - Signature of Phenylring fluctuations T2 - Frühjahrstagung der Deutschen Physikalsichen Gesellschaft, Dresden CY - Dresden, Germany DA - 2011-03-13 PY - 2011 AN - OPUS4-24642 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Kusche, Nadine A1 - Münzenberger, Sven A1 - Schukar, Vivien T1 - KALFOS - a validation facility for strain transfer characterization of surface-applied strain sensors N2 - Strain sensors embedded in or attached to structural components have to measure the real deformation of the structure over the whole period of use. The user must know how reliably installed sensors provide strain measurement results. For this purpose, test facilities or coupon tests are used. In order to characterize the strain transfer quality from the host structure into surface-applied strain sensors, a unique testing facility has been developed. This facility can be used both for fiber optic and resistance strain sensors. Originally developed for fiber Bragg grating based sensors, the KALFOS facility (=calibration of fiber optic sensors) uses Digital Image Correlation (DIC) and Electronic Speckle Pattern Interferometer (ESPI) as unbiased referencing methods. It is possible to determine experimentally the strain transfer mechanism under combined thermal and mechanical loading conditions. This experimental characterization method will reveal weaknesses in commonly used strain sensors, and the investigation of the material systems used for fiber optic and other strain sensors (particularly the coating/substrate - adhesive combination). The KALFOS facility allows matching of specific measurement requirements with environmental conditions. T2 - SAE 2011 AeroTech Congress & Exhibition CY - Toulouse, France DA - 18.10.2011 KW - Fiber optic sensors KW - Structural health monitoring KW - Validation KW - Strain sensor KW - Surface application PY - 2011 DO - https://doi.org/10.4271/2011-01-2606 IS - Paper 2011-01-2606 SP - 1 EP - 7 AN - OPUS4-24643 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - Standards and guidelines for numerical welding simulation PY - 2011 SN - 1001-1382 VL - 459 IS - 9 SP - 5 EP - 8 PB - Jixie Dianzi Gongye Bu * Harbin Hanjie Yanjiusuo AN - OPUS4-24644 LA - zho AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Litzba, Andreas A1 - Berger, Wolfgang A1 - Kalbe, Ute A1 - Krüger, Oliver T1 - Vergleich von Übereinstimmungstests mit Säulen- und Schüttelverfahren am Beispiel PAK- und MKW-belasteter Böden N2 - Mit dem Entwurf der im Januar 2011 vom Bundesumweltministerium vorgelegten Mantelverordnung, welche eine Novelle der Bundes-Bodenschutz- und Altlastenverordnung sowie der Grundwasserverordnung sowie die neue Ersatzbaustoffverordnung (ErsatzbaustoffV) umfasst, werden neue Methoden zur Herstellung von wässrigen Eluaten im Gesetzestext verankert, In der Novelle der BBodSchV werden in diesem Zusammenhang für organische Schadstoffe u.a. Säulen- oder Schüttelverfahren genannt. Bei den Säulenversuchen sollen Perlcolate bis zu einem Flüssigkeits-Feststoffverhältnis von 2 1/lcg entsprechend dem Übereinstimmungstest nach DIN 19528 gesammelt werden. Das Schüttelverfahren soll nach E DIN 19527 („Schüttelverfahren zur Untersuchung des Elutionsverhaltens von organischen Stoffen mit einem Wasser/Feststoff-Verhältnis von 2 1/lcg“) durchgeführt werden. In der Ersatzbaustoffverordnung wird als Verfahren zur Herstellung von wässrigen Eluaten bisher nur das Säulenverfahren nach DIN 19528 („Perlcolationsverfahren zur gemeinsamen Untersuchung des Elutionsverhaltens von anorganischen und organischen Stoffen“) genannt. In diesem Beitrag wird ein Vergleich der Ergebnisse von Säulen- und Schüttelverfahren als Übereinstimmungstest für Böden und Bodenmaterialien, welche mit polyzyklischen aromatischen Kohlenwasserstoffen (PAK) und Mineralölkohlenwasserstoffen (MICW) belastet sind, vorgenommen. KW - Elutionsverfahren KW - Übereinstimmungstest KW - Säulenverfahren KW - Schüttelverfahren KW - Kontaminierte Böden KW - PAK KW - MKW PY - 2011 SN - 0942-3818 SN - 1864-8371 VL - 20 IS - 5 SP - 205 EP - 210 PB - Schmidt CY - Berlin AN - OPUS4-24646 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Balke, Christian A1 - Schendler, Thomas T1 - Möglichkeiten und Grenzen der Ereignisauswertung - aufgzeigt am Beispiel Human Factor T2 - 12. Meinungs- und Erfahrungsaustausch für Sachverständige nach § 29a Abs. 1 BImSchG, VdS Schadensverhütung CY - Cologne, Germany DA - 2011-07-13 PY - 2011 AN - OPUS4-24647 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Schukar, Vivien A1 - Kusche, Nadine A1 - Münzenberger, Sven T1 - KALFOS - A Validation Facility for Strain Transfer Characterization of Surface-Applied Strain Sensors T2 - SAE AeroTech Toulouse 2011 CY - Toulouse, France DA - 2011-10-17 PY - 2011 AN - OPUS4-24588 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppe, Enrico A1 - Bartholmai, Matthias T1 - Wireless Sensor Network with Temperature Compensated Measuring Technology for Long-Term Structural Health Monitoring of Buildings and Infrastructures System T2 - Eurosensors XXV CY - Athens, Greece DA - 2011-09-04 PY - 2011 AN - OPUS4-24589 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pavlovic, Mato A1 - Boehm, R. A1 - Müller, Christina A1 - Ronneteg, U. T1 - Evaluation of the Transmit Receive Longitudinal (TRL) Ultrasonic Inspection of the Nodular Cast Iron Insert for Permanent Storage of High-Level Radioactive Waste by Means of Probalbility of Detection T2 - ASNT Spring Research Symposium and Conference CY - San Francisco, CA, USA DA - 2011-03-21 PY - 2011 AN - OPUS4-24590 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiele, Marc A1 - Pirskawetz, Stephan A1 - Rogge, Andreas T1 - Untersuchung der Schädigungsevolution in Beton unter Ermüdungsbeanspruchung mit Hilfe der Schallemissionsanalyse T2 - DGZfP: 18. Kolloquium Schallemission CY - Wetzlar, Germany DA - 2011-10-27 PY - 2011 AN - OPUS4-24591 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppe, Enrico A1 - Bartholmai, Matthias T1 - Tracking Persons using a Radio-Based Multi-Sensor System T2 - 2011 International Conference on Indoor Positioning and Indoor Navigation (IPIN) CY - Guimarães, Portugal DA - 2011-09-21 PY - 2011 AN - OPUS4-24592 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Asadi, S. A1 - Schiller, J.H. A1 - Lilienthal, A. A1 - Bartholmai, Matthias T1 - An Artificial Potential Field based Sampling Strategy for a Gas-Sensitive Micro-Drone T2 - IEEE/RSJ International Conference on Intelligent Robots and Systems - Workshop on Robotics for Environmental Monitoring (WREM2011) CY - San Francisco, CA, USA DA - 2011-09-25 PY - 2011 AN - OPUS4-24593 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Bartholmai, Matthias T1 - Adaptive ortsaufgelöste Gaskonzentrationsmessungen mit einer Mikrodrohne T2 - AK Sensorik CY - Berlin, Germany DA - 2011-08-24 PY - 2011 AN - OPUS4-24594 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiele, Marc A1 - Rohrmann, Rolf A1 - Said, Samir A1 - Schmid, Wolfgang A1 - Rücker, Werner T1 - Ermüdung von Beton unter hochzyklischen Beanspruchungen T2 - VDI-Spezialseminar: Abdichtung, Sanierung und Ertüchtigung von Fundamenten bei Windenergieanlagen CY - Hamburg, Germany DA - 2011-10-13 PY - 2011 AN - OPUS4-24595 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija A1 - Kanzler, Daniel A1 - Müller, Christina A1 - Fahlbruch, B. A1 - Pitkänen, J. A1 - Ronneteg, U. T1 - "HUMAN FACTORS" BEI DER DATENAUSWERTUNG DER ZFP AM BEISPIEL DER NUKLEAREN ENDLAGERUNG N2 - Untersucht wird die Endlagerung des hoch reaktiven nuklearen Abfalls, die Zuverlässigkeit der ZfP und die Human Factors Methode. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 PY - 2011 AN - OPUS4-24596 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witt, Jens A1 - Breithaupt, Mathias A1 - Erdmann, Jessica A1 - Krebber, Katerina T1 - Humidity Sensing based on Microstructured POF Long Period Gratings T2 - 20th International Conference on Plastic Optical Fibers CY - Bilbao, Spain DA - 2011-09-14 PY - 2011 AN - OPUS4-24597 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Portella, Pedro Dolabella A1 - Klinger, Christian A1 - Bettge, Dirk T1 - Schadensanalyse an Eisenbahnkomponenten T2 - Seminarvortrag am Institut für Werkstofftechnik, Universität Kassel CY - Kassel, Germany DA - 2011-01-27 PY - 2011 AN - OPUS4-24668 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beckmann, Jörg A1 - Schmidt, Richard A1 - Ewert, Uwe A1 - Berndt, Anja T1 - Strategien zur EU-weiten Zertifizierung von Detektions-Systemen, mit denen chemische, biologische, radioaktive und nukleare Gefahrstoffe sowie Explosivstoffe nachgewiesen werden können T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24670 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beckmann, Jörg A1 - Fratzscher, Daniel A1 - von Chrzanowski, Lars A1 - Ewert, Uwe T1 - Spectral and Spatial Nondestructive Examination of Dielectric Materials with THz Time Domain Spectroscopy T2 - REVIEW OF PROGRESS IN QUANTITATIVE NDE 2011 CY - Burlington, VT, USA DA - 2011-07-17 PY - 2011 AN - OPUS4-24671 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beckmann, Jörg A1 - Fratzscher, Daniel A1 - von Chrzanowski, Lars A1 - Ewert, Uwe T1 - Anwendungen von THz-Technologien für die Sicherheit und Zerstörungsfreien Werkstoffprüfung T2 - Werkstattgespräch Terahertz-Technologien für den Ganzkörperscanner - Neue Ansätze für die berührungsfreie Passagierkontrolle, MATNET/ SustAir & BAM, Ludwig Erhard Saal, BAM CY - Berlin, Germany DA - 2011-10-27 PY - 2011 AN - OPUS4-24672 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Portella, Pedro Dolabella A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - High power laser hybrid welding for ship building T2 - Welding Symposium, COTEQ 2011, 11a Conferencia de Tecnologia de Equipamentos CY - Ipojuca, Brazil DA - 2011-05-12 PY - 2011 AN - OPUS4-24673 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna A1 - Kunte, Hans-Jörg A1 - Schwibbert, Karin A1 - Conradi, Bianca A1 - Boenke, Viola T1 - Material und Umwelt: Mikroben als Materialbesiedler T2 - GfKORR-Arbeitskreis "Mikrobiell beeinflusste Korrosion" der DECHEMA-Fachgruppe "Mikrobielle Materialzerstörung und Materialschutz" CY - Frankfurt am Main, Germany DA - 2011-10-21 PY - 2011 AN - OPUS4-24675 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wienecke, Bernd-Uwe T1 - Verwendung von Gefahrgutverpackungen: Hinweise und Tipps zur Vermeidung von Fehlern T2 - Berlin-Brandenburger Gefahrguttage CY - Berlin, Germany DA - 2011-11-03 PY - 2011 AN - OPUS4-24677 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Regina A1 - Kreutzbruck, Marc A1 - Maierhofer, Christiane T1 - Numerische Verfahren für die aktive Thermografie zur Untersuchung von Rückwandgeometrien N2 - In diesem Beitrag werden numerische Verfahren zur Erkennung und Charakterisierung von Fehlstellen, Schichtdicken, Wanddicken und Inhomogenitäten mittels aktiver Thermografie vorgestellt. Eine uantitative Beurteilung der nicht immer zugänglichen Rückwand eines Bauteils (Minderdicken) ist durch Inversion thermografischer Messdaten möglich. Diese quantitativen Informationen können durch iterative Methoden vom Gauß-Newton-Typ (Inversion) gewonnen werden. Als reale Prüfobjekte werden ca. 2 cm dicke PVC-Platten mit örtlich variierender Rückwandgeometrie untersucht. Die Erwärmung erfolgt mit Blitzlampen, welche die PVC-Platte kurzzeitig um mehrere K erwärmt. Ein wichtiger Teil der Inversion ist die Simulation des Experiments, welche mit Finite-Elemente-Methoden (FEM) in 2D realisiert wird. Da Inversion und active Thermografie automatisierbar sind, bietet die Kombination breite Anwendungsgebiete innerhalb der Industrie. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Deutschland DA - 30.05.2011 KW - Inversion KW - Aktive thermografie KW - Wanddicke KW - Rückwand KW - Minderdicken KW - Schichtdicken PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-252812 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (P45) SP - 1 EP - 6 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25281 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Meyer, S. A1 - Richter, S. A1 - Balski, Matthias A1 - Hagendorf, C. T1 - Trace element analysis in crystalline silicon PY - 2011 SN - 1757-1197 VL - 14th Edition IS - 4th Quarter, November SP - 34 EP - 39 PB - Semiconductor Media CY - London AN - OPUS4-25284 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krietsch, Arne A1 - Scheid, Marc T1 - Tests on suitability of a new pyrotechnical igniter for the determination of explosion characteristics of dust clouds in 20-L-sphere and 1-m³-vessel N2 - Safety characteristics are essential for the design of preventive and protective explosion measures. According to international Standards explosion characteristics of dust clouds are determined in 20-L-sphere and l-m3-vessel. The ignition of respective dust samples is realized vvith special pyrotechnical igniters with energy of 1 kJ or 5 kJ vvhich are defined in the testing Standards. However Sobbe in Germany is the only Company at the moment which sells such igniters. The paper presents results of a comparative study between the 5 kJ Sobbe igniter and a 5 kJ igniter manufactured by Sirnex in Czech Republic. The study has been conducted under participation of BAM Federal Institute for Materials Research and Testing, Institute for Occupational Safety and Health of the German Social Accident Insurance (IFA). Berufsgenossenschaft Nahrungsmittel und Gastgewerbe (BGN) and Swiss Institute for Promotion of Safety and Security (Swissi). For the study six dusts from different product groups with various explosion severities and ignitabilities were chosen. The tests were carried out in the 20-L-sphere as well as in the l-m3-vessel. Maximum explosion overpressure Pmax, dust explosion constant Kst and lower explosion limit LEL were determined. Furthermore tests with a high speed and a thermal imaging camera were carried out, in order to compare burning time and flame pattern of Sobbe and Simex igniter. KW - Explosion characteristics of dusts KW - 20-L-sphere KW - 1-m³-vessel KW - Pyrotechnical igniter KW - Dust explosion testing KW - Explosionskenngrößen KW - Bestimmungsmethoden KW - 20-l-Kugel KW - 1-m³-Behälter KW - Pyrotechnischer Zünder KW - Sicherheitstechnische Kenngrößen PY - 2011 SN - 1347-9466 VL - 72 IS - 6 SP - 174 EP - 178 CY - Tokyo AN - OPUS4-25285 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Bürgisser, Philip T1 - Der Einfluss von puzzolanischen Zusatzstoffen vulkanischen Ursprungs auf die Alkali-Kieselsäure-Reaktion (AKR) im Beton PY - 2011 SP - 1 EP - 135 CY - Berlin AN - OPUS4-25287 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rodrigues, M. A1 - Schreiner, M. A1 - Melcher, M. A1 - Guerra, M. A1 - Salomon, J. A1 - Radtke, Martin A1 - Alram, M. A1 - Schindel, N. T1 - Characterization of the silver coins of the Hoard of Becin by x-ray based methods N2 - Four hundred sixteen silver coins stemming from the Ottoman Empire (16th and 17th centuries) were analyzed in order to confirm the fineness of the coinage as well as to study the provenance of the alloy used for the coins. As most of the coins showed the typical green patina on their surfaces due to corrosion processes which have led to the depletion of copper in the near-surface domains of the silver coins in comparison to their core composition, small samples by cutting splinters from the coins had to be taken, embedded in synthetic resin and cross-sectioned in order to investigate the true-heart metal composition. The type of the alloy was investigated as well as if coins minted in different locations demonstrated homogeneous traits concerning the predominant impurities which could suggest a common ore. Several X-ray based techniques (µ-XRF, µ-SRXRF and µ-PIXE) could be applied in order to determine the silver contents as well as the minor and trace elements. Finally, SEM/EDX was applied in order to study the homogeneity/heterogeneity of the coins and the presence of surface enrichments. In general, the silver content of the analyzed specimen varies between 90% and 95%. These outcomes have not supported the historical interpretations, which predict that during the period studied a debasement of approximately 44% of the silver content of the coins should have occurred. KW - PIXE KW - SRXRF KW - SEM/EDX KW - Silver coins PY - 2011 DO - https://doi.org/10.1016/j.nimb.2011.04.068 SN - 0168-583X SN - 1872-9584 VL - 269 IS - 24 SP - 3041 EP - 3045 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-25289 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Torge, Manfred A1 - Krug, Sonja A1 - Bücker, Michael A1 - Feldmann, Ines A1 - Scharf, Holger A1 - Witthuhn, Heike T1 - Investigation of mercury emissions of historic tin-mercury-mirrors N2 - With the implementation of glass casting in France in the second half of the 17th century, larger mirrors could be produced. So-called tin-mercury mirrors were made by coating glass with tin amalgam. Today, many historical mirrors are partly damaged, the image quality is compromised, and the material integrity of the mirror is threatened. The transformation from tin into an oxide starts at the surface of the amalgam and proceeds down to the glass surface. The mercury dissolves as a liquid or gaseous phase. The amalgam layer is destroyed, so that conservation is necessary. Conservators must follow strict safety precautions while handling amalgam mirrors because of possible mercury emissions and corrosion of the amalgam, during which elemental mercury accumulates near the mirror frame in droplets and is emitted into the air. In a research project, the quantity of the mercury emissions from historical mirrors was examined and a technique to decrease these emissions was developed. T2 - International Conference on Non-destructive Investigations and Microanalysis for the Diagnostics and Conservation of Cultural and Environmental Heritage (ART 2011) CY - Florence, Italy DA - 13.04.2011 KW - Emission KW - Quecksilber KW - Zinn-Amalgamspiegel PY - 2011 UR - https://www.ndt.net/search/docs.php3?id=11425 SN - 1435-4934 VL - 16 IS - 10 SP - 1 EP - 8 PB - NDT.net CY - Kirchwald AN - OPUS4-25270 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weidner, Steffen T1 - ^Mass spectrometry of synthetic polymers applications and limitations of the MALDI-TOF technique T2 - APST 2 (Advances in Polymer Science and Technology) CY - Linz, Austria DA - 2011-09-28 PY - 2011 AN - OPUS4-25271 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Subaric-Leitis, Andreas T1 - Instrumentierte Eindringprüfung zur ortsaufgelösten Festigkeitsanalyse T2 - 5. Zwick-Roell-Härte-Symposium CY - Ulm, Germany DA - 2011-07-05 PY - 2011 AN - OPUS4-25273 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Subaric-Leitis, Andreas T1 - Bestimmung lokaler Spannungs-Dehnungs-Kurven an Widerstandspunktschweißverbindungen von hochfesten Mehrphasenstählen mittels instrumentierter Eindringprüfung T2 - Tagung Werkstoffprüfung 2011 des DVM CY - Berlin, Germany DA - 2011-12-01 PY - 2011 AN - OPUS4-25274 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klinger, Christian A1 - Bettge, Dirk A1 - Häcker, Ralf A1 - Heckel, Thomas A1 - Gohlke, Dirk A1 - Klingbeil, Dietmar T1 - Schadensanalyse zum Radsatzwellenbruch ICE3 N2 - Am 9. Juli 2008 entgleiste ein Hochgeschwindigkeits-Triebzug der Baureihe 403, ICE3, bei der Ausfahrt aus dem Kölner Hauptbahnhof. Ursache dafür war der Schwingbruch einer Radsatzwelle. Im Auftrag der Staatsanwaltschaft Köln untersuchte die BAM die Schadensteile, insbesondere die gebrochene Treibradsatz-Hohlwelle. Zunächst wurden das Drehgestell, der Antriebsstrang, die Räder, die Bremsen und die gebrochene Radsatzwelle visuell untersucht und deren Zustand dokumentiert. Anschließend erfolgte die zerstörungsfreie Prüfung der beiden Bruchstücke der Hohlwelle mit teilmechanisierter Ultraschall-Handprüfung. Vor der Zerlegung der Radsatzwelle wurden ausgewählte Maße kontrolliert und die Oberfläche eingehend untersucht. Nach der Probenahme und Präparation wurden die relevanten spezifizierten Eigenschaften des Wellenwerkstoffs überprüft. Mittels Bruchflächenanalyse konnte die Startstelle des Schwingrisses lokalisiert, aufgrund der starken Sekundärschäden auf der Bruchfläche und an den Bruchkanten jedoch nicht direkt ausgewertet werden. Durch die Kombination von Mikro-Computertomographie und Ultraschall-Tauchtechnik wurden u. a. nahe der Schwingriss-Startstelle Inhomogenitäten erkannt, die durch metallographische Zielpräparation als nichtmetallische Einschlüsse identifiziert wurden. Die Größe dieser Einschlüsse ist gemäß gefordertem Reinheitsgrad unzulässig. Vergleichbare Einschlüsse in diesem hochbeanspruchten Bereich der Radsatzwelle haben vermutlich den Schwingriss initiiert. T2 - 43. Tagung des DVM-Arbeitskreises Bruchvorgänge - Bruchmechanische Werkstoff- und Bauteilbewertung: Beanspruchungsanalyse, Prüfmethoden und Anwendungen CY - Rostock, Germany DA - 22.02.2011 KW - Radsatzwellenbruch KW - Nichtmetallische Einschlüsse KW - Reinheitsgrad KW - Ultraschall-Hohlwellenprüfung KW - Railway axle KW - Fatigue crack KW - Root cause KW - Cologne accident PY - 2011 SP - 1 EP - 6 AN - OPUS4-25275 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völz, Uwe A1 - Mrasek, Heinz A1 - Heckel, Thomas T1 - Querfehlerprüfung an anisotropen Engspaltschweißnähten mit Gruppenstrahlern N2 - Die Prüfung von anisotropen Schweißnähten auf Querfehler stellt auch heute noch eine Herausforderung für die Ultraschallprüfung dar. Das gilt insbesondere für das Auffinden kleiner rissartiger Fehlstellen in einer unbeschliffenen Wurzel. Ursachen dafür sind zum einen das ausgeprägte Beugungs-, Streuungs- und Reflexionsverhalten solcher Nähte und zum anderen die störenden Formanzeigen aus dem Wurzelbereich, die sicher von den Fehlstellen unterschieden werden müssen, um Fehlinterpretationen bei der Bewertung der Anzeigen zu vermeiden. In der vorliegenden Arbeit werden an einer 85 mm dicken und 6 bis 10 mm breiten Engspaltschweißnaht mit stängelkristalliner Struktur rissartige Testfehler in Form erodierter Nuten untersucht. Die 2 und 4 mm tiefen Nuten sind mit 5 mm Länge kürzer als die Wurzelbreite. Die Wurzel ist nicht beschliffen und hat eine Überhöhung von ca. 2 mm. Ziel ist es, die Fehlstellen von den Form- und Gefügeanzeigen zu unterscheiden und sicher zu detektieren. Eine Größenbestimmung ist nicht vorgesehen. Durch den Einsatz der Gruppenstrahlertechnik ist es möglich, optimale Einschallparameter zu finden, mit denen diese Aufgabe gelöst werden kann. Es werden zwei azimutal schwenkende lineare Gruppenstrahlerprüfköpfe mit Vorsatzkeil in SE-Technik verwendet, die so auf beiden Seiten der Schweißnaht angeordnet sind, dass sich ihre Schallfelder unabhängig von der Einschallrichtung in der Schweißnahtwurzel überlagern. Damit ist es möglich, optimale Einschallwinkel für das Prüfproblem zu finden und in einer Prüffahrt gleichzeitig in beiden Einschallrichtungen längs der Schweißnaht zu prüfen. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Ultraschall KW - Gruppenstrhaler KW - Anisotropie KW - Austenit KW - Nickellegierung KW - Querfehler KW - Schweißnaht PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-252777 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (P49) SP - 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25277 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kitze, Jessica A1 - Boehm, Rainer A1 - Brackrock, Daniel A1 - Montag, Hans-Joachim A1 - Völz, Uwe A1 - Brekow, Gerhard A1 - Kreutzbruck, Marc T1 - SAFT-Rekonstruktion und 3D Lokalisation aus Ultraschallmessungen mit Matrix- und Linear-Arrays in Tauchtechnik N2 - Die Kombination der Synthetic Aperture Focusing Technique (SAFT) mit der Tauchtechnik stellt eine besondere Herausforderung dar. Zwei für SAFT notwendige Bedingungen – die große Schallbündeldivergenz und die Kenntnis über den Ort des Senders bzw. des Empfängers, der für die phasenrichtige Überlagerung der Echosignale genau bekannt sein muss – lassen sich einfach erfüllen, wenn kleine, fast punktförmige Sensoren direkt auf der Oberfläche des Prüfobjektes ankoppeln. Diese Anordnung ist in der Regel nicht vereinbar mit den praktischen Ansprüchen an die Signalqualität und die Flexibilität der Prüftechnik. Werden jedoch Prüfköpfe mit üblichen Abmessungen und zudem noch mit Vorlaufstrecken verwendet, dann ist die Bestimmung der Sensororte und der Schalllaufwege durch die brechende Fläche nicht mehr trivial, wenn man die für SAFT geforderte Genauigkeit in Rechnung stellt. Etwas anderes, aber ein im Prinzip einfacher Weg zur räumlichen Lokalisation von Echoquellen ist die Auswertung des 2D Sektorscans eines Matrixarrays und dessen dreidimensionale Darstellung. Durch gezielte Steuerung des Arrays gelingt auf einfache Weise die ortsrichtige Zuordnung. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Matrix-Array KW - Linear-Array KW - SAFT-Rekonstruktion in Tauchtechnik KW - Räumliche Darstellung PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-252788 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Di.3.A.2) SP - 1 EP - 11 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25278 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sojref, Regine A1 - Güther, Wolfgang T1 - Solvent-based redispersion of fine (<200 nm) corundum powder pre-milled in water T2 - ECerS XII - 12th Conference of the European Ceramic Society CY - Stockholm, Sweden DA - 2011-06-19 PY - 2011 AN - OPUS4-25291 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Musolff, André A1 - Quercetti, Thomas A1 - Müller, Karsten A1 - Droste, Bernhard A1 - Komann, Steffen T1 - Drop test program with half scale model CASTOR HAW/TB2 N2 - Federal Institute for Materials Research and Testing (BAM) is the competent authority for mechanical and thermal safety assessment of transport packages for spent fuel and high level waste in Germany. In context with package design approval of the new German high level waste cask CASTOR® HAW28M, BAM performed several drop tests with a half scale model of the CASTOR® HAW/TB2. The cask is manufactured by Gesellschaft für Nuklear Service mbH and was tested under accident transport conditions on the 200 tons BAM drop test facility at the BAM Test Site Technical Safety. For this comprehensive test program, the test specimen CASTOR® HAW/TB2 was instrumented at 21 measurement planes with altogether 23 piezo resistive accelerometers, five temperature sensors and 131 triaxial strain gauges in the container interior and exterior respectively. The strains of four representative lid bolts were recorded by four uniaxial strain gauges per each bolt. Helium leakage rate measurements were performed before and after each test in the above noted testing sequence. The paper presents some experimental results of the half scale CASTOR® HAW/TB2 prototype (14 500 kg) and measurement data logging. It illustrates the extensive instrumentation and analyses that are used by BAM for evaluating the cask performance to the mechanical tests required by regulations. Although some of the quantitative deceleration, velocity and strain values cannot be shown because of confidentially issues, they are provided qualitatively to illustrate the types of measurements and methodologies used at BAM. KW - IAEA drop testing KW - Half scale model KW - Experimental test PY - 2011 DO - https://doi.org/10.1179/1746510911Y.0000000013 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 22 IS - 3 SP - 154 EP - 160 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-25293 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rahman, Mehbub-Ur A1 - Kolkoori, Sanjeevareddy A1 - Prager, Jens T1 - Elastische Wellenausbreitung in austenitischen Schweißnähten - Numerische Simulation und deren messtechnische Validierung T2 - 37. Deutsche Jahrestagung für Akustik (DAGA 2011) CY - Düsseldorf, Germany DA - 2011-03-21 PY - 2011 AN - OPUS4-25295 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brackrock, Daniel A1 - Kreutzbruck, Marc A1 - Schenk, Gottfried A1 - Deutsch, W.A.K. A1 - Maxam, K. A1 - Platte, M. T1 - Untersuchungen an Vergleichskörper-Reflektoren T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-25296 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas T1 - Die Gläserne Schiene T2 - DGZfP-Arbeitskreis München CY - Munich, Germany DA - 2011-09-29 PY - 2011 AN - OPUS4-25297 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gohlke, Dirk A1 - Heckel, Thomas A1 - Völz, Uwe A1 - Klinger, Christian A1 - Goebbels, Jürgen T1 - Einsatz von hochauflösenden Volumenprüfverfahren zur Verifikation und Verbesserung der Prüfaussage am Beispiel von Eisenbahnradsatzwellen T2 - Seminar Fachausschuss Ultraschall CY - Offenbach am Main, Germany DA - 2011-11-09 PY - 2011 AN - OPUS4-25298 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ploigt, Roy A1 - Dohse, Elmar A1 - Schenk, Gottfried T1 - Schnittstellenkonzepte für digitale Ultraschallprüfgeräte T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-25299 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rack, A. A1 - Weitkamp, T. A1 - Zanette, I. A1 - Morawe, C. A1 - Vivo Rommeveaux, A. A1 - Tafforeau, P. A1 - Cloetens, P. A1 - Ziegler, E. A1 - Rack, T. A1 - Cecilia, A. A1 - Vagovic, P. A1 - Harmann, E. A1 - Dietsch, R. A1 - Riesemeier, Heinrich T1 - Coherence preservation and beam flatness of a single-bounce multilayer monochromator (beamline ID19-ESRF) N2 - Larger spectral bandwidth and higher photon flux density are the major advantages of multilayer monochromators over crystal-based devices. Especially for synchrotron-based hard X-ray microimaging applications the increased photon flux density is important in order to achieve high contrast and resolution in space and/or time. However, the modifications on the beam profile induced by reflection on a multilayer are a drawback which can seriously harm the performance of such a monochromator. A recent study [A. Rack, T. Weitkamp, M. Riotte, D. Grigoriev, T. Rack, L. Helfen, T. Baumbach, R. Dietsch, T. Holz, M. Krämer, F. Siewert, M. Meduna, P. Cloetens, E. Ziegler, J. Synchrotron Radiat. 17 (2010) 496–510] has shown that the modifications in terms of beam flatness and coherence preservation can be influenced via the material composition of the multilayer coating. The present article extends this knowledge by studying further material compositions used on a daily basis for hard X-ray monochromatization at the beamline ID19 of the European Synchrotron Radiation Facility. KW - Multilayer mirrors KW - X-rays KW - X-ray optics KW - Coherence KW - X-ray monochromators KW - X-ray imaging KW - X-ray phase contrast KW - Synchrotron radiation PY - 2011 DO - https://doi.org/10.1016/j.nima.2010.11.069 SN - 0168-9002 SN - 0167-5087 VL - 649 IS - 1 SP - 123 EP - 127 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-25240 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Arlt, Tobias A1 - Manke, I. A1 - Wippermann, K. A1 - Tötzke, C. A1 - Markötter, H. A1 - Riesemeier, Heinrich A1 - Mergel, J. A1 - Banhart, J. T1 - Investigation of the three-dimensional ruthenium distribution in fresh and aged membrane electrode assemblies with synchrotron X-ray absorption edge tomography N2 - Synchrotron X-ray absorption edge imaging was used to investigate the ruthenium distribution in both fresh and aged Pt/Ru-based membrane electrode assemblies (MEA) of direct methanol fuel cells. MEAs aged in different ways were analyzed: artificially aged by MeOH depletion and aged for 1700 h in an operating fuel cell stack. An element sensitive tomographic technique – differential X-ray absorption edge tomography – was applied allowing for a 3D-visualization of the ruthenium distribution within the MEA. We found a markedly changed Ru distribution after aging which is correlated to the GDL structure, the flow field geometry, and CO2 transport in the methanol solution. KW - Edge tomography KW - Ruthenium distribution KW - Direct methanol fuel cells KW - Synchrotron X-ray KW - PtRu corrosion PY - 2011 DO - https://doi.org/10.1016/j.elecom.2011.05.013 SN - 1388-2481 VL - 13 IS - 8 SP - 826 EP - 829 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-25243 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Markötter, H. A1 - Manke, I. A1 - Krüger, P. A1 - Arlt, Tobias A1 - Huassmann, J. A1 - Klages, M. A1 - Riesemeier, Heinrich A1 - Hartnig, C. A1 - Scholta, J. A1 - Banhart, J. T1 - Investigation of 3D water transport paths in gas diffusion layers by combined in-situ synchrotron X-ray radiography and tomography N2 - The three-dimensional water distribution and water transport paths in the gas diffusion layer (GDL) and the adjacent micro-porous layer (MPL) of a polymer electrolyte membrane fuel cell (PEMFC) were analyzed during cell operation. The technique of quasi in-situ X-ray tomography was used for a 3D visualization of the water distribution and the structure of the GDL at different operating conditions. Based on findings from in-situ radiographic measurements water transport paths were detected and subsequently examined by tomography. The combination of these 2D and 3D techniques allows for a fully three-dimensionally resolved visualization of transport paths through the GDL. KW - Polymer electrolyte membrane fuel cell (PEMFC) KW - Radiography KW - Tomography KW - Synchrotron X-ray imaging KW - Gas diffusion layer (GDL) KW - Water transport paths PY - 2011 DO - https://doi.org/10.1016/j.elecom.2011.06.023 SN - 1388-2481 VL - 13 IS - 9 SP - 1001 EP - 1004 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-25244 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan A1 - Rübner, Katrin A1 - Meng, Birgit T1 - Ganzheitliche Bewertung der Einsatzmöglichkeit von Sekundärrohstoffen in Beton T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25245 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bleul, Regina A1 - Bachran, D. A1 - Thiermann, Raphael A1 - Bertin, Annabelle A1 - Fuchs, H. A1 - Maskos, Michael T1 - Probing polymersome-protein and -cell interactions: influence of different end-groups and environments N2 - Developing polymersomes for drug delivery purposes requires a deeper understanding of their behavior in physiological environment. We performed the self-assembly and in-situ loading of polybutadiene-block-polyethyleneoxide (PB-b-PEO) polymersomes in a continuous process using micromixers. Varying the length and end-groups of the starting block copolymer allows us to control the polymer membrane thickness and surface functionalities (hydroxyl or carboxylic acid), required to realize a further coupling with specific cell targeting ligands. To get a deeper understanding of these polymersomes in physiological environment, we studied the cellular response (HeLa cells) in presence of various polymersomes, and showed by cytotoxicity tests the relative biocompatibility of the systems. Flow cytometry experiments at 4?°C in PBS buffer showed a different behavior of hydroxyl-functionalized vesicles compared to carboxylic acid-functionalized vesicles. On the contrary cell binding in DMEM medium supplemented with 10% FCS was almost completely blocked with both kinds of polymersomes. Protein adsorption measurements by dynamic light scattering confirmed that protein binding occurs in all cases, which apparently influences the particle-cell interaction. This study contributes towards a deeper understanding of polymersomes in biological environment and further investigations will help us to design highly effective polymersomes for in vitro as well as in vivo applications. KW - Drug delivery KW - End-group functionality KW - Particle-cell interaction KW - Physiologic environment KW - Polymersomes KW - Protein adsorption PY - 2011 DO - https://doi.org/10.1002/masy.201100042 SN - 1022-1360 SN - 0258-0322 SN - 1521-3900 VL - 309/310 IS - 1 SP - 134 EP - 140 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-25246 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rübner, Katrin T1 - Reststoffverwertung im Betonbau T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25247 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Gezielte Beeinflussung der Eigenschaften von Instandsetzungsmörteln T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25248 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ünal, Murat A1 - Kühne, Hans-Carsten T1 - Restaurierung von Betonverglasungen: Instandsetzungstechniken und -mörtel T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25249 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krebber, Katerina ED - Ramos, G. A. T1 - Structural health monitoring by smart technical textiles based on fiber optic sensors N2 - Technical textiles with embedded distributed fiber optic sensors have been developed for the purposes of structural health monitoring in geotechnical and civil engineering. The distributed fiber optic sensors are based on Brillouin Scattering in silica optical fibers and OTDR in polymer optical fibers. Such “smart” technical textiles can be used for reinforcement of geotechnical and masonry structures and the embedded fiber optic sensors can provide information about the condition of the structures and detect the presence of any damages and destructions in real time. Thus, structural health monitoring of critical geotechnical and civil infrastructures can be realized. The paper highlights the results achieved in this innovative field in the framework of several German and European projects. T2 - SHMII-5 - 5th International conference on structural health monitoring of intelligent infrastructure CY - Cancún, Mexico DA - 11.12.2011 PY - 2011 IS - Keynote Lecture SP - 1 EP - 10 PB - National Autonomous University of Mexico CY - Mexico City AN - OPUS4-25261 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rahman, Mehbub-Ur A1 - Prager, Jens T1 - Modelling of Lamb Wave Propagation with Elastodynamic Finite Intergration Technique T2 - International Congress on Ultrasonics CY - Gdansk, Poland DA - 2011-09-05 PY - 2011 AN - OPUS4-25263 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Schukar, Vivien T1 - FOS standards and methodologies to validate strain measurements with FBG sensors (invited lecture) T2 - International SPIE Conference on Smart Structures and Materials CY - San Diego, CA, USA DA - 2011-03-08 PY - 2011 AN - OPUS4-25264 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Schukar, Vivien T1 - Validation of strain sensors to achieve reliable measurement results (invited lecture) T2 - 5th International Conference on Structural Health Monitoring of Intelligent Infrastructure (SHMII-5) CY - Cancún, Mexico DA - 2011-12-11 PY - 2011 AN - OPUS4-25265 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, M. A1 - Habel, Wolfgang A1 - Vaterodt, K. A1 - Heidmann, G. A1 - Vogelsang, R. A1 - Weissenberg, W. A1 - Sekula, O. A1 - Pepper, D. A1 - Emanuel, H. A1 - Plath, R. T1 - Optical PD Detection in Stress Cones of HV Cable Accessories T2 - 8th International Conference on Insulated Power Cables 2011 CY - Versailles, France DA - 2011-06-19 PY - 2011 AN - OPUS4-25266 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schilder, Constanze A1 - Kohlhoff, Harald A1 - Hofmann, Detlef A1 - Habel, Wolfgang T1 - Structure-Integrated Fiber-Optic Strain Wave Sensor for Concrete Pile Testing and Monitoring T2 - 5th International Conference on Structural Health Monitoring of Intelligent Infrastructure (SHMII-5) CY - Cancún, Mexico DA - 2011-12-11 PY - 2011 AN - OPUS4-25267 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - "Instandhaltung" - aktuelle Themen beim Schutz und Instandsetzen von Betonbauteilen T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25250 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterhus, Lennart A1 - Rübner, Katrin T1 - Potenziale SiO2-reicher Filterschlämme für den Einsatz in hydraulischen Bindemitteln T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25252 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rübner, Katrin A1 - Jakubcová, Petra A1 - Schnell, A. T1 - Blähgranulate aus Bau-und Abbruchabfällen als leichte Gesteinkörnung für Beton T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25254 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas T1 - Prüfung von Eisenbahnschienen mit dem Schienenprüfzug bei hohen Geschwindigkeiten bis 20 m/s T2 - Bahntechnik-Symposium 2011 CY - Berlin, Germany DA - 2011-12-09 PY - 2011 AN - OPUS4-25255 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt A1 - Wrobel, Norma T1 - Safety and Security: How to Assess Risk T2 - Croatian Society of NDT, MATEST 2011 CY - Split, Croatia DA - 2011-11-02 PY - 2011 AN - OPUS4-25257 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weise, Frank T1 - Neuartige Prüfmethodologien zur Schadensanalyse in Betonen T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25258 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kolkoori, Sanjeevareddy A1 - Rahman, Mehbub-Ur A1 - Prager, Jens A1 - Chinta, P.K. T1 - Computationally Efficient Ray Tracing Algorithm for Simulation of Transducer Fields in Anisotopic Materials T2 - 21st Annual ISNT Conference on Non Destructive Evaluation (NDE 2011) CY - Chennai, India DA - 2011-12-08 PY - 2011 AN - OPUS4-25300 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kreutzbruck, Marc A1 - Harrer, Andrea A1 - Prager, Jens A1 - Guderian, Matthias A1 - Meyer-Plath, Asmus T1 - Thermoacoustic generation of airbone ultrasound using carbon materials at the micro- and nanoscale T2 - 15th International Symposium on Applied Electromagnetics and Mechanics CY - Naples, Italy DA - 2011-09-06 PY - 2011 AN - OPUS4-25301 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Regina A1 - Maierhofer, Christiane A1 - Röllig, Mathias A1 - Götschel, S. A1 - Weiser, M. T1 - Fast defect shape reconstruction based on travel time in pulse thermography T2 - Nondestructive Testing of Materials and Structures CY - Istanbul, Turkey DA - 2011-05-15 PY - 2011 AN - OPUS4-25302 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vöse, Markus A1 - Fedelich, Bernard T1 - Development of a cohesive model for grain boundary damage under creep T2 - 7th Meeting of the TC2 on Micromechanisms of the European Structural Integrity Society CY - Berlin, Germany DA - 2011-11-24 PY - 2011 AN - OPUS4-25303 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jotzies, André A1 - Plarre, Rüdiger T1 - Bekämpfung verborgener Befallsherde der Kleidermotten durch Schlupfwespen T2 - Arbeitskreis Vorrrats- und Materialschutz der Deutschen Phytomedizinischen Gesellschaft und der Deutschen Gesellschaft für allgemeine und angewandte Entomologie CY - Berlin, Germany DA - 2011-11-16 PY - 2011 AN - OPUS4-25304 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Borho, N. A1 - Schoknecht, Ute T1 - Auswaschungen nach EN 16105 und Dynamic Surface Leaching Test T2 - Kolloquium "Auswaschungen an beregneten Fassaden" CY - Berlin, Germany DA - 2011-11-15 PY - 2011 AN - OPUS4-25307 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Schukar, Vivien ED - Ramos, G. A. T1 - Validation of strain sensors to achieve reliable measurement results N2 - Fiber optic strain sensors are increasingly used and sensor Systems are provided with specifications. Even if the performance is well specified, the strain characteristics of the sensor, strain transfer factor, mechanical stability under thermal influences, the performance of applied strain sensors can seriously differ from virgin sensor’s the performance. Therefore the contribution considers validation issues to come to reliable strain measurements and how to validate strain measurements of applied sensors. A new validation facility will be presented. T2 - SHMII-5 - 5th International conference on structural health monitoring of intelligent infrastructure CY - Cancún, Mexico DA - 11.12.2011 PY - 2011 IS - Session 20, Topic 2.3 SP - 1 EP - 13 PB - National Autonomous University of Mexico CY - Mexico City AN - OPUS4-25309 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, M. A1 - Vaterrodt, K. A1 - Heidmann, G. A1 - Habel, Wolfgang A1 - Vogelsang, R. A1 - Weissenberg, W. A1 - Sekula, O. A1 - Pepper, D. A1 - Emanuel, H. A1 - Plath, R. T1 - Optical PD detection in stress cones of HV cable accessories N2 - Sensitive partial discharge (PD) measurements on HV/EHV cable systems are usually based on electrical or electromagnetic PD detection. Unfortunately, interferences may significantly reduce sensitivity, especially in on-site after-installation testing and, even more, in on-line PD monitoring. This paper deals with optical PD detection, which is absolutely immune to any kind of electromagnetic interference. Optical PD detection necessarily requires transparent or translucent insulation systems to be applicable. Stress cone elements for HV/EHV cable accessories meet the requirements for optical PD detection, if made from transparent silicone elastomers. T2 - 8th International Conference on Insulated Power Cables CY - Versailles, France DA - 19.06.2011 PY - 2011 IS - B.8.4 SP - 1 EP - 5 PB - Jicable CY - Paris AN - OPUS4-25310 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Röben, R. A1 - Hüttl, R. A1 - Kuchejda, M. ED - Ramos, G. A. T1 - Monitoring of corrosion protection in reinforced concrete structures using an integrated pH optode N2 - Corrosion in steel-reinforced concrete structures is a critical issue. Corrosion appears if the pH value of the concrete matrix decreases due to deterioration of the Calcium hydroxide layer on the Steel surface. The safest Information about potential danger of Steel corrosion is the knowledge of the pH value of concrete. The paper presents a Tiber optic pH sensor for long-term monitoring of the pH value of reinforced concrete structures at risk from corrosion. The sensor probe is small (about 8 mm in diameter), can be embedded into the concrete matrix and observe changes in pH over years. Several sensor probes can be staggered to detect the progression of pH decrease. The pH values can be resolved with 0.1 to 0.2 pH value in the ränge between 12.0 and 9.5. The structure of the pH measurement System, longterm test results and the design to achieve stable probes will be explained. Experienee from test applications of pH sensors embedded in grouted anchors and in concrete components for a cooling tower will be presented. T2 - SHMII-5 - 5th International conference on structural health monitoring of intelligent infrastructure CY - Cancún, Mexico DA - 11.12.2011 PY - 2011 IS - Session 15, Topic 4.5 SP - 2 EP - 8 PB - National Autonomous University of Mexico CY - Mexico City AN - OPUS4-25311 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kreutzbruck, Marc T1 - Progress in Defect Sizing Nondestructive Testing Methoads T2 - International Symposium on Fatigue Design & Material Defects CY - Trondheim, Norway DA - 2011-05-23 PY - 2011 AN - OPUS4-25312 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kreutzbruck, Marc T1 - Progress in Acoustical Defect Sizing NDT Methods for the Inspection of Power Plant Components T2 - NDE 2011 CY - Chennai, India DA - 2011-12-08 PY - 2011 AN - OPUS4-25313 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kreutzbruck, Marc T1 - Recent NDE activities at BAM in Acoustical and Electromagnetic Methods T2 - Kolloquium IGCAR CY - Kalpakkam, India DA - 2011-12-13 PY - 2011 AN - OPUS4-25314 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kreutzbruck, Marc T1 - Modern techniques in Nondestructive Testing Methods T2 - Summerschool; Graduiertenkolleg TU Illmenau CY - Göttingen, Germany DA - 2011-09-28 PY - 2011 AN - OPUS4-25315 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kreutzbruck, Marc T1 - Potenziale technischer und biologischer Leichtbausysteme & Moderne bildgebende Verfahren in der zerstörungsfreien Prüfung zur Inspektion von Leichtbaukomponenten T2 - Kolloquium IZFP/Universität des Saarlandes CY - Saarbrücken, Germany DA - 2011-03-09 PY - 2011 AN - OPUS4-25316 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kreutzbruck, Marc T1 - Progress in Defect Sizing Nondestructive Testing Methods T2 - Kolloquium ALSTOM CY - Baden, Switzerland DA - 2011-08-18 PY - 2011 AN - OPUS4-25317 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kreutzbruck, Marc T1 - Bildgebende zerstörungsfreie Materialprüfung mittels akustischer und elektromagnetischer Sensor- und Aktorsysteme T2 - Kolloquium Fakultät für Maschinenwesen und Betriebswissenschaften, TU Wien CY - Vienna, Austria DA - 2011-06-01 PY - 2011 AN - OPUS4-25318 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kreutzbruck, Marc T1 - Insitu-Prüfung von ICE-Radsatzwellen; Skizze zu möglichen Prüfverfahren und ihrer physikalischen Machbarkeit T2 - Meeting Verband Deutscher Bahnindustrie CY - Berlin, Germany DA - 2011-09-21 PY - 2011 AN - OPUS4-25319 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pirskawetz, Stephan A1 - Weise, Frank A1 - Fontana, Patrick T1 - Zwangsinduzierte Rissbildung bei erhärtendem Hochleistungsbeton T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25230 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fontana, Patrick T1 - Frühe Rissbildung in Beton durch plastisches Schwinden T2 - 52.DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25231 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fontana, Patrick A1 - Müller, Urs A1 - Meng, Birgit T1 - Schädigungsmechanismen in Beton-aktuelle Forschung T2 - 52.DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 07.11.2011 PY - 2011 AN - OPUS4-25233 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Voland, Katja A1 - Weise, Frank A1 - Meng, Birgit T1 - Untersuchung des Einflusses der Gefügedichte von Betonen auf die AKR mit neuartiger Prüftechnik T2 - 52. DAfStb-Forschungskolloquium 2011, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25234 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Recknagel, Christoph T1 - Schutz von Ingenieurbauwerken-Was leisten Abdichtungssysteme? T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25235 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Urs A1 - Kargol, Marta A1 - Gardei, André T1 - Der Einfluss der Zementart auf die Leistungsfähigkeit von Hydrophobierungsmitteln T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25237 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Urs T1 - Schutz von Betonen: Aktuelle Forschung zur Wirkungsweise und Dauerhaftigkeit von Schutzmaßnahmen T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25238 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Huismann, Sven A1 - Korzen, Manfred A1 - Rogge, Andreas T1 - Tragverhalten von Stützen aus hochfestem Stahlbeton unter Brandbeanspruchung T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25239 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wehrstedt, Klaus-Dieter A1 - Horn, J. T1 - IGUS: An example of good international laboratory co-operation T2 - Sitzung des DECHEMA Arbeitsausschusses "Reaktionstechnik sicherheitstechnisch schwieriger Prozesse" CY - Leuna, Germany DA - 2011-09-14 PY - 2011 AN - OPUS4-24328 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter T1 - Burner for peroxy fuels (Peroxy-BAM® Burner) T2 - 25. Deutscher Flammentag - Verbrennung und Feuerung CY - Karlsruhe, Germany DA - 2011-09-14 PY - 2011 AN - OPUS4-24329 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheid, Marc A1 - Krietsch, Arne T1 - Nanomaterials - Explosion Prevention and Protection T2 - XIX World Congress on Safety and Health at Work - issa-training-course nanotechnology CY - Istanbul, Turkey DA - 2011-09-11 PY - 2011 AN - OPUS4-24330 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai A1 - Schmidtchen, Ulrich T1 - Einschätzung des Gefahrenpotenzials im Umgang mit Wasserstoff am Beispiel Brennstoffzelle T2 - Seminar "Innovative Stromversorgung für Bahnanlagen" CY - Magdeburg, Germany DA - 2011-08-24 PY - 2011 AN - OPUS4-24331 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gravenkamp, Hauke A1 - Prager, Jens A1 - Saputra, A. A. A1 - Chongmin, Song T1 - Detection of defects in thin-walled structures by means of Lamb waves T2 - International Congress on Ultrasonics 2011 CY - Gdansk, Poland DA - 2011-09-05 PY - 2011 AN - OPUS4-24332 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kolkoori, Sanjeevareddy A1 - Kreutzbruck, Marc A1 - Rahman, Mehbub-Ur A1 - Prager, Jens A1 - Chinta, P.K. T1 - Quantitative Evaluation of Ultrasonic Sound Field in Anisotropic Austenitic welds using 2D Ray tracing model T2 - 38th Annual Reviwe if Progress in Quantitative Non- Destructive Evaluation (QNDE 2011), University of Vermont CY - Burlington, VT, USA DA - 2011-07-17 PY - 2011 AN - OPUS4-24333 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Konersmann, Rainer T1 - Gefahrguttransport auf dem Meeresboden - wie sicher sind Offshore-Erdgaspipelines? N2 - Mit der Erschließung der Erdöl- und Erdgasfelder in den Weltmeeren wurde es notwendig, eine bekannte Transporttechnologie, die Pipeline, für den Unterwassereinsatz zu ertüchtigen. Für die Seefahrt und die Fischereiindustrie ergaben sich dadurch neue Konfliktsituationen. Durch die gemeinsamen Betätigungsräume mussten die etablierten Praktiken der Seeschifffahrt und der Fischereitechnik neu austariert werden, z. B. hinsichtlich der Ankerplätze und der Fischereizonen. Dieses notwendige Nebeneinander verlief nicht immer reibungsfrei und war mit einigen spektakulären Unfällen verbunden. Nachfolgend wird ein kurzer Einblick in die Problematik der Offshore-Pipelines gegeben. KW - Risiko KW - Gefahrgut KW - Unterwasserpipeline PY - 2011 SN - 2191-0073 VL - 1 IS - 9 SP - 56 EP - 60 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-24334 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krietsch, Arne A1 - Scheid, Marc T1 - Brand- und Explosionsschutz bei nanoskaligen Stäuben N2 - Die Nanotechnologie gilt als die Wachstumsbranche der nächsten Jahrzehnte. Während die gesundheitlichen Wirkungen von nanoskaligen Materialien bereits in zahlreichen Studien und Forschungsvorhaben näher untersucht wurden und werden, sind die Erfahrungen und Erkenntnisse über Brand- und Explosionsgefahren von Stäuben im Nanometerbereich bzw. von Partikeln < 1 µm bislang noch kaum erforscht. Die Bestimmung sicherheitstechnischer Kenngrößen von Nanostäuben – die die Grundlage für eine Gefährdungsbeurteilung und das Auslegen von Schutzmaßnahmen bilden – erfolgte bislang nur in sehr geringem Umfang. Die Untersuchungen wurden zudem in Analogie zu den Verfahren für Mikrostäube durchgeführt. Es wurde jedoch weder überprüft, ob die für Mikrostäube etablierten Prüfverfahren für eine sichere Bewertung des Brenn- und Explosionsverhaltens geeignet sind, noch ob durch freigesetzten Staub bei einer entsprechenden Ermittlung der Kenngrößen Gesundheitsrisiken bestehen. Der Beitrag beschreibt den Stand des Wissens im Bereich Brand- und Explosionsschutz für Stäube im Nanometerbereich und berichtet über ein bei der BAM Bundesanstalt für Materialforschung und -prüfung laufendes Projekt zur Beseitigung der momentanen Defizite, gefördert von der Deutschen Gesetzlichen Unfallversicherung (DGUV) sowie verschiedenen Berufsgenossenschaften. KW - Explosionsschutz KW - Nanomaterialien KW - Sicherheitstechnische Kenngrößen PY - 2011 SN - 2191-0073 VL - 1 IS - 9 SP - 10 EP - 14 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-24336 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mix, Renate A1 - Friedrich, Jörg Florian T1 - Improvement of adhesivity of polypropylene by its surface modification using the aerosol dielectric barrier discharge N2 - Plasma processes are used in many fields of Science and technology. While a plasma oxygen treatment produces a broad variety of different oxygen-containing functional groups, tailored - surface functionalisation demands preset functional groups in known concentration. Due to the fact that most of plasma experiments need expensive vacuum equipment increased efforts are to observe to apply atmospheric pressure plasma processes. Thus, Dielectric Barrier Discharge (DBD) and corona treatment of polymer foils have a long tradilion in industry to modify them for printing, laminating, adhesion promotion, etc. Thercibre, increasing interest is observed to make these atmospheric pressure processes more effeclive. Newly developed methods like plasma-printing were used for surfaces in biological and medical applications or for printed circuits. T2 - ADHESION `11 - 11th Triennial conference on the science and technology of adhesion and adhesives CY - York, UK DA - 07.09.2011 PY - 2011 SP - 253 EP - 256 AN - OPUS4-24337 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hong, Shuxian T1 - Reinforcement corrosion assessment with Ground Penetrating Radar T2 - SmartEN Multi-Disciplinary Workshop CY - Athens, Greece DA - 2011-07-06 PY - 2011 AN - OPUS4-24228 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hong, Shuxian T1 - Reinforcement corrosion detection by Ground Penetrating Radar T2 - EU-Midterm Review, Marie Curie Initial Training Network SmartEN CY - Athens, Greece DA - 2011-07-09 PY - 2011 AN - OPUS4-24229 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen A1 - Droste, Bernhard A1 - Wille, Frank T1 - Transport of Large Nuclear Power Plant Components - Experiences in Mechanical Design Assessment - T2 - Workshop BAM/US.NRC CY - Washington, D.C., USA DA - 2011-07-11 PY - 2011 AN - OPUS4-24230 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eisenacher, Germar A1 - Neumann, Martin A1 - Scheidemann, Robert A1 - Wille, Frank A1 - Droste, Bernhard T1 - Approach for a Finite Element Material Model for Wood for Application in Mechanical Safety Cases of Transport Packages T2 - INMM 52nd Annual Meeting CY - Palm Desert, CA, USA DA - 2011-07-17 PY - 2011 AN - OPUS4-24231 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eisenacher, Germar A1 - Neumann, Martin A1 - Scheidemann, Robert A1 - Wille, Frank A1 - Droste, Bernhard T1 - Impact Limiter Modeling - an Approach for an FE Material Model for Wood T2 - USNRC Workshop CY - Washington, D.C., USA DA - 2011-07-11 PY - 2011 AN - OPUS4-24232 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Guderian, Matthias A1 - Daschewski, Maxim A1 - Harrer, Andrea A1 - Prager, Jens A1 - Kreutzbruck, Marc A1 - Mach, Reinhard A1 - Meyer-Plath, Asmus T1 - Carbon nanomaterials as broadband airborne ultrasound transducer T2 - Proceedings of the Annual World Conference on Carbon 2011 CY - Shanghai, China DA - 2011-07-24 PY - 2011 AN - OPUS4-24233 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maul, Ronald A1 - Müller, Chr. A1 - Koch, Matthias A1 - Mehtner, F.-J. A1 - Nehls, Irene T1 - Der Keimprozess von Getreide als Auslöser für die Maskierung des Mykotoxins Deoxynivalenol im Lebensmittel T2 - 40. Deutscher Lebensmittelchemikertag 2011 CY - Halle (Saale), Germany DA - 2011-09-12 PY - 2011 AN - OPUS4-24234 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Koch, Matthias A1 - Bremser, Wolfram A1 - Köppen, Robert A1 - Krüger, Rita A1 - Rasenko, Tatjana A1 - Siegel, David A1 - Nehls, Irene T1 - Certification of reference materials for ochratoxin A analysis in coffee and wine N2 - Mycotoxins are important non-anthropogenic food and feed contaminants, which can be present on almost every agricultural commodity. Effective consumer protection therefore essentially depends on food surveillance by reliable quantitative analysis enabled by appropriate quality control. Certified (matrix) reference materials (CRMs) are versatile tools to support Quality assurance. However, in the case of ochratoxin A (OTA), a hepato- and nephrotoxic mycotoxin, which is regulated in various foods, there is a lack of suitable CRMs. This lack has now been overcome by the development of two European Reference Materials (ERM®) for the Determination of OTA in roasted coffee (ERM®-BD475) and red wine (ERM®-BD476). This article discusses the material preparation process as well as the results of homogeneity and stability testing. Furthermore, the results of the inhouse certification studies carried out at BAM Federal Institute for Materials Research and Testing are presented and discussed. Interlaboratory comparison studies involving selected expert laboratories with documented Expertise in the field of mycotoxin analysis were conducted to confirm the certified values determined by BAM. The certified ochratoxin A values and their corresponding expanded uncertainties (k = 2) were assigned in full compliance with the requirements of ISO Guide 35 and are as follows: (6.0 ± 0.6) µg kg-1 for roasted coffee, ERM®-BD475, and (0.52 ± 0.11) µg L-1 for red wine, ERM®-BD476. KW - OTA KW - Coffee KW - Wine KW - Food safety and quality KW - European reference materials KW - CRM PY - 2011 DO - https://doi.org/10.1007/s00769-011-0783-0 SN - 0949-1775 SN - 1432-0517 VL - 16 SP - 429 EP - 437 PB - Springer CY - Berlin AN - OPUS4-24235 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eisenacher, Germar A1 - Scheidemann, Robert A1 - Neumann, Martin A1 - Wille, Frank A1 - Droste, Bernhard T1 - Approach for a finite element material model for wood for application in mechanical safety cases of transport packages N2 - BAM Federal Institute for Materials Research and Testing is the competent authority for mechanical safety assessment of transport packages for radioactive material in Germany. The further development of state-of-the-art technology concerning assessment methods is essential for a qualified work of involved designers and authority experts. The paper gives an example of current development done to improve understanding and modeling capabilities of wood filled impact limiter. In order to reduce the loads applied to the package containment, which result from regulatory drop tests, most packages are protected by energy dissipating impact limiter. Wood, encapsulated by steel sheets, is one of the materials typically used for energy dissipation in these impact limiter. Very often, mechanical safety cases regarding the 9 m drop test are performed computationally, where it is essential to use reliable and verified computational methods and models. In this context, the paper presents an approach for a finite element material model for wood. Thereby, the mechanical behavior of wood under compression loading is the focus of the development work. Additionally, material orientation as well as strain rate, temperature and lateral constraint may vary. A large number of experiments, particularly compression tests, was designed and performed to establish an adequate experimental database for modeling verification. The experimental results enabled the derivation of necessary requirements: The material model has to take into account strain rate and temperature dependencies as well as the anisotropic characteristics of the material, a proper yield criterion, flow rule and hardening law. Such a material model is currently not available in established commercial dynamic finite element codes. Thus it is necessary to create a user-defined material model considering the mentioned requirements. A first step was done by determining a yield surface as well as detecting flow and hardening mechanisms from experimental force-deflection curves. In a next step the LS-DYNA material model MAT_75 was altered according to conclusions of former BAM development work, regarding the modeling of post-peak softening as a function of lateral constraint. Future research will contain the further development, implementation and verification of a material model for wood. T2 - 52nd INMM Annual meeting CY - Palm Desert, CA, USA DA - 17.07.2011 KW - Impact limiter KW - Material model wood KW - Transport package PY - 2011 SP - 1 EP - 8 AN - OPUS4-24236 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gross, Thomas A1 - Unger, Wolfgang T1 - Degradation of organic surfaces during XPS analysis: Case study and proposal of a routine method to describe the photon flux T2 - ECASIA '11 - 14th European Conference on Applications of Surface and Interface Analysis CY - Cardiff, Wales DA - 2011-09-04 PY - 2011 AN - OPUS4-24237 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Robertson, Daniela A1 - Böhning, Martin A1 - Schröder, Hartmut A1 - Brummermann, K. A1 - Kaudinya, I. A1 - Saathoff, F. T1 - Möglichkeiten der Abschätzung der Langzeitbeständigkeit von Kunststoffdichtungsbahnen (KDB) auf Polyolefinbasis für den Tunnelbau N2 - Im Rahmen eines von der Bundesanstalt für Straßenwesen (BASt) initiierten Forschungsvorhabens (15.449/2007/ERB: „Prüfverfahren zur Beurteilung der Lebensdauer von Kunststoffdichtungsbahnen für Straßentunnel“) wurden anhand von Untersuchungen an Kunststoffdichtungsbahnen (KDB) auf Basis von Polyolefinwerkstoffen die Möglichkeiten der Beurteilung der oxidativen Langzeitbeständigkeit sondiert. Im Mittelpunkt stand die Erprobung des Autoklaventests in Anlehnung an DIN EN ISO 13438 (Methode C1/C2) an ausgewählten, für den Tunnelbau repräsentativen marktüblichen KDB-Produkten. Die Untersuchungen im Autoklaven bei erhöhten Temperaturen (60 °C, 70 °C und 80 °C) und Sauerstoffdrücken (11, 21 und 51 bar) wurden durch vergleichende Versuche im Wärmeschrank (Ofen) bei erhöhter Temperatur (85 °C) in Anlehnung an DIN EN 14575 ergänzt. Die KDBProdukte wurden außerdem einer eingehenden Materialcharakterisierung (Zugprüfung, DMA, DSC) unterzogen. Weiterhin wurden Bauwerksdaten recherchiert und auf ihre Nutzbarkeit zur Bewertung und Prüfbarkeit der Langzeitbeständigkeit von KDB in Tunneln betrachtet. Ziel war auch, die Anwendbarkeit des bisher vorgeschlagenen Extrapolationsmodells zur Auswertung der Ergebnisse von Autoklaventests an im Tunnelbau marktüblichen Produkten für Nutzungsdauern über 25 Jahre zu überprüfen und zur Entwicklung eines geeigneten Prüfverfahrens beizutragen. Der Beitrag geht auf Ergebnisse des Vorhabens ein und zeigt erste Schlussfolgerungen und weiteren Untersuchungsbedarf auf. Die Ergebnisse werden in den „Empfehlungen zu Dichtungssystemen im Tunnelbau EAG-EDT“ des Arbeitskreises 5.1 „Kunststoffe in der Geotechnik und im Wasserbau“ berücksichtigt, deren 2. Auflage in Vorbereitung ist. Aspekte des thermischen Verhaltens der eingesetzten Werkstoffe sowie mögliche Anpassungen der Prüfrandbedingungen für die Autoklaventests werden ergänzt und Hinweise zur Interpretation von Prüfergebnissen gegeben. Außerdem wurden inzwischen ausgehend von den Ergebnissen des Forschungsvorhabens erste Autoklaven-Ringversuche in drei Prüfinstitutionen initiiert. T2 - 12. Informations- und Vortragstagung über "Kunststoffe in der Geotechnik" CY - Munich, Germany DA - 03.03.2011 KW - Kunststoffdichtungsbahnen auf Polyolefinbasis KW - Oxidative Langzeitbeständigkeit KW - Autoklaventest - beschleunigte Alterung KW - DSC KW - DMA PY - 2011 SN - 978-3-940476-26-5 IS - Geotechnik Sonderheft 2011 SP - 35 EP - 42 AN - OPUS4-24399 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppe, Enrico A1 - Bartholmai, Matthias ED - Tsamis, C. ED - Kaltsas, G. T1 - Wireless sensor network with temperature compensated measuring technology for long-term structural health monitoring of buildings and infrastructures N2 - Damage to buildings occurs if a construction component fails. The result is a partial or total collapse which can be dangerous for people for example if it's a bridge or a large hall. The collapse of the terminal building at the Airport Charles de Gaulle in Paris and the damage at the historic City Archives of Cologne are typical examples of such accidents. Another problem is the contradiction of the increasing volume of traffic (particularly heavy traffic) and the great age of bridges. The probability increases that the load-bearing capacity of a bridge decreases. For example the collapses of the Mississippi Bridge and of the Inntal Motorway Bridge can be seen as results. Therefore it is necessary to control endangered structures during their life span. In order to prevent these kinds of accidents, the Federal Institute for Materials Research and Testing developed a radio-based, self-configuring measuring system in cooperation with the ScatterWeb Company, Berlin (Germany). This measuring system consists of identically designed sensor modules which are self-sustaining, wireless, act as transmitters and receivers and are equipped with a special sensor technology for long-term monitoring of buildings or engineering facilities. The sensor unit uses strain gauges for stress analysis and contains interfaces for additional sensors. The system in particular applies to buildings and structures for transport and traffic and large-scale industrial facilities, where a subsequent wiring installation is difficult or impossible. T2 - Eurosensors XXV CY - Athens, Greece DA - 04.09.2011 KW - Multi-Hop WSN KW - SHM KW - Temperature and Frequency Compensation KW - Funksensorik KW - Sensornetzwerk KW - Multihop KW - Strukturüberwachung KW - Temperaturkompensation PY - 2011 UR - http://www.sciencedirect.com/science/article/pii/S1877705811059236 IS - Paper 1197 SP - 1 EP - 5 PB - Elsevier AN - OPUS4-24401 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppe, Enrico A1 - Bartholmai, Matthias A1 - Liers, A. A1 - Schiller, J. T1 - Tracking persons using a radio-based multi-sensor system N2 - A multi-sensor system for 3D localization was developed and named BodyGuard. It combines body movement sensing and a guard system for the tracking and recording of the status of persons. BodyGuard was designed to monitor and transmit the movement of a person radio-based and to transform that data into a spatial coordinate. This paper describes how the BodyGuard system works, what components the system consists of, how the individual sensor data is converted into 3D motion data, with which algorithms the individual sensors are processed, how individual errors are compensated and how the sensor data are fused into a 3D Model. T2 - IPIN 2011 - International conference on indoor positioning and indoor navigation CY - Guimaraes, Portugal DA - 21.09.2011 KW - Wireless sensor network (WSN) KW - Embedded systems KW - Sensor calibration and validation KW - Person tracking KW - Inertial navigation system KW - Inertial measurement unit PY - 2011 SP - 1 EP - 4 AN - OPUS4-24402 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Torge, Manfred A1 - Kruschke, Detlef T1 - Investigations into 20th Century Commercial Glass paints and enamels T2 - Forum for the Conservation of Stained-Glass Windows, Stained Glass after 1920: Technology and Conservation CY - Lisbon, Portugal DA - 2011-09-26 PY - 2011 AN - OPUS4-24406 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg A1 - Pentzien, Simone A1 - Conradi, Andrea A1 - Koter, Robert T1 - Femtosecond, picosecond and nanosecond pulse laser cleaning of artificially soiled paper model samples T2 - Konferenz "Laser in the Conservation of Artworks" (LACONA IX) CY - London, England DA - 2011-09-07 PY - 2011 AN - OPUS4-24238 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dietrich, Paul A1 - Horlacher, T. A1 - Girard-Lauriault, Pierre-Luc A1 - Gross, Thomas A1 - Lippitz, Andreas A1 - Min, Hyegeun A1 - Wirth, Thomas A1 - Castelli, R. A1 - Seeberger, P. H. A1 - Unger, Wolfgang T1 - Surface chemical characterization of carbohydrate films on gold T2 - ECASIA '11 CY - Cardiff, Wales DA - 2011-09-09 PY - 2011 AN - OPUS4-24239 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wirth, Thomas A1 - Recknagel, Christoph T1 - TOF-SIMS investigation of coated glass beads T2 - 18th International Conference on Secondary Ion Mass Spectrometry CY - Riva del Garda, Italy DA - 2011-09-18 PY - 2011 AN - OPUS4-24240 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan A1 - Procop, Mathias A1 - Unger, Wolfgang T1 - A Test Material and quick Procedure for Checking the Performance of X-Ray Spectrometers attached to a SEM T2 - ECASIA '11 14th European Conference on Application of Surface and Interface Analysis CY - Cardiff, Wales DA - 2011-09-04 PY - 2011 AN - OPUS4-24241 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dietrich, Paul A1 - Funk, Christian A1 - Gross, Thomas A1 - Unger, Wolfgang A1 - Weigel, W. T1 - Epoxy-functionalized Surfaces: Surface chemical analysis and fluorescence labeling of surface species T2 - ECASIA '11 CY - Cardiff, Wales DA - 2011-09-09 PY - 2011 AN - OPUS4-24242 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dietrich, Paul A1 - Horlacher, T. A1 - Gross, Thomas A1 - Castelli, R. A1 - Wirth, Thomas A1 - Seeberger, P. H. A1 - Unger, Wolfgang T1 - Surface chemical Analysis of Microarrays: Problems and Perspectives T2 - ECASIA'11 CY - Cardiff, Wales DA - 2011-09-09 PY - 2011 AN - OPUS4-24243 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Petzet, S. A1 - Peplinski, Burkhard A1 - Bodkhe, S.Y. A1 - Cornel, P. T1 - Recovery of phosphorus and aluminium from sewage sludge ash by a new wet chemical elution process (SESAL-phos-recovery process) N2 - The potential of a new wet chemical process for phosphorus and aluminium recovery from sewage sludge ash by sequential elution with acidic and alkaline solutions has been investigated: SESAL-Phos (sequential elution of sewage sludge ash for aluminium and phosphorus recovery). Its most innovative aspect is an acidic pre-treatment step in which calcium is leached from the sewage sludge ash. Thus the percentage of alkaline soluble aluminium phosphates is increased from 20 to 67%. This aluminium phosphate is then dissolved in alkali. Subsequently, the dissolved phosphorus is precipitated as calcium phosphate with low heavy metal content and recovered from the alkaline solution. Dissolved aluminium is recovered and may be reused as a precipitant in wastewater treatment plants. KW - Aluminium phosphate KW - Calcium phosphate KW - Phosphorus recovery KW - Sewage sludge ash PY - 2011 DO - https://doi.org/10.2166/wst.2011.682 SN - 0273-1223 VL - 64 IS - 3 SP - 693 EP - 699 PB - IWA Publishing CY - Bristol AN - OPUS4-24244 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Musolff, André A1 - Komann, Steffen A1 - Droste, Bernhard A1 - Müller, Karsten A1 - Quercetti, Thomas T1 - Drop test program with a HLW cask model - performance, measurements and results N2 - BAM (Federal Institute for Material Research and Testing) is the competent authority for mechanical and thermal safety assessment of transport packages for spent fuel and high level waste (HLW) in Germany. In context with package design approval of the new German HLW cask CASTOR HAW28M, BAM performed several drop tests with a half-scale model of the CASTOR HAW/TB2. The test model was manufactured by GNS (Gesellschaft fur Nuklear Service mbH) and tested under accident transport conditions on the 200 tons BAM drop test facility at the BAM Test Site Technical Safety. For this comprehensive test program the test specimen CASTOR HAW/TB2 was instrumented at 21 measurement planes with altogether 23 piezo-resistive accelerometers, five temperature sensors and 131 tri-axial strain gauges in the container interior and exterior, respectively. The strains of four representative lid bolts were recorded by four uniaxial strain gauges per each bolt. Helium leakage rate measurements were performed before and after each test in the above noted testing sequence. The paper presents some experimental results of the half-scale CASTOR HAW/TB2 prototype (14,500 kg) and measurement data logging. T2 - 52nd INMM Annual meeting CY - Palm Desert, CA, USA DA - 17.07.2011 KW - Drop test results KW - Spent fuel transport cask KW - Impact limiter KW - Measurement methods KW - Drop test program PY - 2011 SP - 1 EP - 9 AN - OPUS4-24245 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Beck, M. A1 - Burkert, Andreas T1 - Korrosion von Stahl in Beton N2 - Die Sicherstellung der Dauerhaftigkeit von Stahlbetonbauwerken erfolgt über Regelwerke, die auf einem umfangreichen Wissen über die Eigenschaften der verwendeten Baustoffe beruhen. Weiterhin dienen Beobachtungen und Untersuchungen dazu, eine genaue Aussage über den Ist-Zustand von Bauwerken abgeben zu können. Eine detaillierte Bestandsaufnahme und Zustandsanalyse auf Grundlage geeigneter Messdaten ermöglicht eine Prognose über die verbleibende Nutzungsdauer. Fortlaufende Untersuchungen können auch dazu genutzt werden, Wartungs- und Sanierungsintervalle auf der Grundlage von Regelwerken zu koordinieren und so den Erhalt von Bauwerken zu sichern. KW - Stahlbeton KW - Passivität KW - Depassivierung KW - Karbonatisierung KW - Chlorinduzierte Korrosion PY - 2011 VL - 2 SP - 5 EP - 8 PB - VBD-Geschäftsstelle CY - Hannover AN - OPUS4-24246 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Klapper, Helmuth Sarmiento A1 - Burkert, Andreas A1 - Burkert, Annette A1 - Lehmann, Jens A1 - Villalba, A.L. T1 - Influence of surface treatments on the pitting corrosion of type 304 stainless steel by electrochemical noise measurements N2 - Surface treatments usually are used to modify the appearance and properties of stainless steel surfaces. Simultaneously, the corrosion resistance of the stainless steel surface being related intrinsically to the spontaneous formation of a passive layer also will be affected. In this respect, the influence of different surface treatments on the corrosion resistance of Type 304 (UNS S30400) stainless steel to pitting corrosion has been evaluated by means of potentiostatic electrochemical noise measurements and surface characterization. Typical industrial treatments including mechanical grinding, glass blasting, and pickling were taken into account. Additionally, special consideration was put on the effect of aging conditions of the passive layer after surface treatments, in particular on the relative humidity. Benefits and limitations of the different applied surface treatments concerning protectiveness of the stainless steel surface were determined and discussed. KW - Corrosion KW - Electrochemical noise KW - Pitting corrosion KW - Stainless steel KW - Surface treatment PY - 2011 DO - https://doi.org/10.5006/1.3613641 SN - 0010-9312 SN - 1938-159X VL - 67 SP - 075004-1 EP - 075004-13 PB - National Association of Corrosion Engineers CY - Houston, Tex. AN - OPUS4-24247 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lange, Axel A1 - Hentschel, Manfred P. A1 - Kupsch, Andreas A1 - Müller, Bernd R. T1 - Correction of diffuse X-ray detector based background N2 - A novel approach to strongly suppress artifacts in radiography and computed tomography caused by the effect of diffuse background Signals (“backlight”) of 2D X-ray detectors is suggested. Depending on the detector geometry the mechanism may be different, either based on the optical scattering of the fluorescent screen materials into optical detection devices or Compton or X-ray fluorescence scattering by the detector components. Consequently, these erroneous intensity portions result in locally different violations of Lambert Beer’s law in single projections (radiographs). When used as input data for computed tomography these violations are directly observed via modulation of the projected mass as a function of the rotation Phase and the sample’s aspect ratio (dynamics). The magnitude of the diffuse Background signal depends on the detector area covered by the projected sample. They are more pronounced the smaller the shaded area and the stronger the total attenuation. Moreover, the local intensity mismatch depends on the attenuation of the sample. We present very basic reference data measured with multiple metal foils at a synchrotron radiation source. Beam hardening artifacts can be excluded due to the monochromatic radiation. The proposed correction procedure assumes a constant (non-local) scattering mechanism. T2 - DIR 2011 - International symposium on digital industrial raidology and computed tomography CY - Berlin, Germany DA - 20.06.2011 KW - Backlight KW - X-ray detector KW - Fluorescence screen KW - Synchrotron radiography KW - Computed tomography PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-243589 SN - 978-3-940283-34-4 IS - DGZfP-BB 128 (Poster 24) SP - 1 EP - 7 PB - Deutsche Gesellscahft für Zerstörungsfreie Prüfung e.V. (DGZfP) AN - OPUS4-24358 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Altenkirch, J. A1 - Gibmeier, J. A1 - Kromm, Arne A1 - Kannengießer, Thomas A1 - Nitschke-Pagel, T. A1 - Hofmann, M. T1 - In situ study of structural integrity of low transformation temperature (LTT)-welds N2 - We discuss the stability of weld residual strain under static and quasi cyclic transverse tensile loading in the elastic and elastic–plastic region. The test welds were joined with low transformation temperature weld filler materials with 10 wt% Cr and varying Ni-content from 8 to 12 wt%. Using neutron diffraction the residual lattice strain in the martensitic α'- and austenitic γ-phase in the fusion zone as well as the ferritic α-phase in the heat affected zone and base metal as induced by welding, superimposed by stepwise tensile loading and after unloading was measured. The amount of retained austenite in the fusion zone increases with increasing Ni-content, but it decreases with increasing load level due to stress induced martensite formation. In the as-welded condition the transverse macroscopic residual lattice strain was found to be in low compression in the fusion zone in each weld, while the heat affected zone was in tension. Local plastic deformation of the γ-phase as a result of yielding during tensile loading in combination with the change in phase fraction resulted in increased macroscopic compression in the fusion zone. The reduced yield strength in the heat affected zone resulted in plastic deformation and a considerable shift into compression. Comparison with the cross weld distribution of the hardness and FWHM of the neutron diffraction interference lines supported the assumption of plastic deformation of the γ- and α-phase in the fusion and heat affected zone, respectively, while the α'-phase in the fusion zone was stressed within the elastic regime only. Microstructural observations as well as measurement of the local γ-phase fraction by means of laboratory X-ray diffraction in the fusion zone strengthen these observations. KW - Low transformation temperature KW - Residual stress KW - Neutron diffraction PY - 2011 DO - https://doi.org/10.1016/j.msea.2011.03.091 SN - 0921-5093 SN - 1873-4936 VL - 528 IS - 16-17 SP - 5566 EP - 5575 PB - Elsevier CY - Amsterdam AN - OPUS4-24359 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Desinfektionsmaßnahmen - Beständigkeit von Werkstoffen T2 - 3. Forum Innenraumhygiene CY - Essen, Germany DA - 2011-02-15 PY - 2011 AN - OPUS4-24361 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Werkstoffe - Medien - Korrosion: Szenen einer Beziehung T2 - DVM-Tag 2011 CY - Berlin, Germany DA - 2011-05-04 PY - 2011 AN - OPUS4-24362 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heinze, Christoph A1 - Schwenk, Christopher A1 - Rethmeier, Michael ED - Zoch, H.-W. ED - Lübben, T. T1 - Influences on the result quality of numerical calculation of welding-induced distortion N2 - The present investigations cover different relevant influences on the numerical calculation of welding-induced distortion. Therefore, a single-layer pulsed gas metal arc (GMA) weld of structural Steel S355J2+N with a thickness Öf5 mm is experimentally and numerically investigated. The influences of mesh density, tack-welds, and continuous cooling transformation (CCT) diagrams on welding-induced distortion are studied. The quality and quantity of These effects are clarified based on the used experimental and numerical set up. The occurring differences between the investigated cases achieve significant values. Consequently, prediction of welding-induced distortion can be improved considering the present investigations. T2 - IDE 2011 - 3rd International conference on distortion engineering 2011 CY - Bremen, Germany DA - 14.09.2011 KW - Welding simulation KW - Welding-induced distortion KW - Mesh analysis KW - Tack welding KW - Continuous cooling transformation behaviour PY - 2011 SN - 978-3-88722-724-1 SP - 277 EP - 285 AN - OPUS4-24363 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Vermeidung von Schäden in der Trinkwasserinstalltion -Tipps für die Praxis T2 - Baukammer Berlin CY - Berlin, Germany DA - 2011-06-28 PY - 2011 AN - OPUS4-24364 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Werkstoffe und Hygiene im Licht der neuen Trinkwasserverordnung und der DIN 50930-6 T2 - DVGW-Erfahrungsaustausch Trinkwasser CY - Brandenburg, Germany DA - 2011-09-14 PY - 2011 AN - OPUS4-24365 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Vorgaben zu Prüfungen und Anforderungen im Warmwasserbereich - Ausblick T2 - 4. Expertenhearing Risiken in der Trinkwasserinstallation CY - Berlin, Germany DA - 2011-10-06 PY - 2011 AN - OPUS4-24366 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sabel, Martin A1 - Feldmann, Ines A1 - Bücker, Michael A1 - Gorbushina, Anna T1 - SEM investigations of biofilms: Environmental-SEM vs. sample drying and low temperature SEM T2 - Microscopy Conference 2011 CY - Kiel, Germany DA - 2011-08-28 PY - 2011 AN - OPUS4-24378 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Prager, Jens A1 - Harrer, Andrea A1 - Daschewski, Maxim A1 - Guderian, Matthias A1 - Meyer-Plath, Asmus A1 - Kreutzbruck, Marc T1 - Thermoacoustic generation of airborne ultrasound using carbon materials at the micro- and nanoscale T2 - 15th International Symposium on Applied Electromagnetics and Mechanics CY - Naples, Italy DA - 2011-09-06 PY - 2011 AN - OPUS4-24381 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Harrer, Andrea A1 - Prager, Jens A1 - Kreutzbruck, Marc A1 - Guderian, Matthias A1 - Meyer-Plath, Asmus A1 - Daschewski, Maxim T1 - Carbon nanomaterials as broadband airborne ultrasound transducer T2 - International congress on Ultrasonics 2011 CY - Gdansk, Poland DA - 2011-09-05 PY - 2011 AN - OPUS4-24382 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bellon, Carsten A1 - Ewert, Uwe A1 - Fratzscher, Daniel A1 - Gollwitzer, Christian A1 - Jaenisch, Gerd-Rüdiger T1 - Simulation of Complex Scan Paths for 3D Reconstruction T2 - International Symposium on Digital Industrial Radiology and Computed Tomography CY - Berlin, Germany DA - 2011-06-20 PY - 2011 AN - OPUS4-24383 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian T1 - Failure criterion based on adhesion for composites under transverse loading T2 - Thermosets 2011 Conference CY - Berlin, Germany DA - 2011-09-21 PY - 2011 AN - OPUS4-24384 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jäger, Christian A1 - Hemmann, Felix A1 - Kosslick, H. A1 - Schulz, A. T1 - Towards nature and quantification of acid sites of amorphous silicia alumina using NMR T2 - Kooperationstreffen, Sasol GmbH CY - Brunsbüttel, Germany DA - 2011-09-27 PY - 2011 AN - OPUS4-24385 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weltschev, Margit T1 - Duplex als Alternative N2 - EDELSTAHL - Die Entwicklung immer besser auf die Füllguteigenschaften abgestimmter, spezieller Stahlqualitäten geht kontinuierlich voran. Ein weiterer Duplexstahl wurde jüngst von der BAM bewertet. KW - Duplexstahl KW - Tankcontainer KW - Tankfahrzeuge KW - Beständigkeitsbewertung KW - BAM-Liste PY - 2011 SN - 0016-5808 VL - 09 SP - 10 EP - 13 PB - Storck CY - Hamburg AN - OPUS4-24387 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Berger, Wolfgang A1 - Kalbe, Ute A1 - Krüger, Oliver A1 - Litzba, Andreas T1 - Vergleich der Ergebnisse von Übereinstimmungstests bei Säulen- und Schüttelversuchen T2 - Jahrestagung der Deutschen Bodenkundlichen Gesellschaft CY - Berlin-Potsdam, Germany DA - 2011-09-03 PY - 2011 AN - OPUS4-24261 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn A1 - Höhm, S. A1 - Rosenfeld, A. A1 - Krüger, Jörg T1 - Femtosecond laser-induced periodic surface structures on materials with varying band gap T2 - International workshop on laser-induced periodic surface structures CY - Enschede, Netherlands DA - 2011-10-11 PY - 2011 AN - OPUS4-24264 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liehr, Sascha A1 - Krebber, Katerina T1 - A dynamic fiber optic strain and power change sensor N2 - A dynamic and quasi-distributed sensor principle for simultaneous measurement of length changes and optical power changes between reflection points in an optical fiber is presented. The technique is based on the incoherent optical frequency domain reflectometry (I-OFDR). Length change resolutions < 1 µm and measurement repetition rates up to 2 kHz can be achieved using standard single-mode and multi-mode optical fibers. Simultaneous length change and refractive index measurement as well as field test results showing the deformation of a masonry building under seismic load are presented. Promising fields of application for this technique are the structural health monitoring sector and chemical process control. T2 - 21st International conference on optical fibre sensors CY - Ottawa, Canada DA - 15.05.2011 KW - Distributed sensor KW - Strain sensor KW - Optical fiber sensor KW - Structural health monitoring KW - OFDR KW - Dynamic sensor PY - 2011 SN - 978-0-8194-8246-4 DO - https://doi.org/10.1117/12.884577 VL - 7753 SP - 775351-1 EP - 775351-4 AN - OPUS4-24266 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ardissone, S. A1 - Kobayashi, H. A1 - Kambara, K. A1 - Rummel, C. A1 - Noel, K.D. A1 - Walker, G.C. A1 - Broughton, William J. A1 - Deakin, W.J. T1 - Role of BacA in lipopolysaccharide synthesis, peptide transport, and nodulation by rhizobium sp. strain NGR234 N2 - BacA of Sinorhizobium meliloti plays an essential role in the establishment of nitrogen-fixing symbioses with Medicago plants, where it is involved in peptide import and in the addition of very-long-chain fatty acids (VLCFA) to lipid A of lipopolysaccharide (LPS). We investigated the role of BacA in Rhizobium species strain NGR234 by mutating the bacA gene. In the NGR234 bacA mutant, peptide import was impaired, but no effect on VLCFA addition was observed. More importantly, the symbiotic ability of the mutant was comparable to that of the wild type for a variety of legume species. Concurrently, an acpXL mutant of NGR234 was created and assayed. In rhizobia, AcpXL is a dedicated acyl carrier protein necessary for the addition of VLCFA to lipid A. LPS extracted from the NGR234 mutant lacked VLCFA, and this mutant was severely impaired in the ability to form functional nodules with the majority of legumes tested. Our work demonstrates the importance of VLCFA in the NGR234-legume symbiosis and also shows that the necessity of BacA for bacteroid differentiation is restricted to specific legume-Rhizobium interactions. KW - Bacteria KW - Rhizobia PY - 2011 DO - https://doi.org/10.1128/JB.01260-10 SN - 0021-9193 SN - 1098-5530 VL - 193 IS - 9 SP - 2218 EP - 2228 PB - American Society for Microbiology CY - Washington, DC AN - OPUS4-24267 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter T1 - Burner for peroxy-fuels (PEROXY-BAM Burner) N2 - A new burner concept (PEROXY-BAM®) for the combustion of liquid organic peroxides (Peroxy-fuels) is presented. As peroxy-fuels are thermally unstable the design of burners for them should be accordingly modified ensuring a safe operation. It is found that 10 to 100 time less amounts of peroxy fuels are required for the same heat flux or output in comparison to hydrocarbons. Correspondingly, the fuel pump power and the volume of combustion chamber (furnace) are also reduced. As a result of less amount of fuel the emissions will also be stepped down and oxygen in the molecule helps to establish conditons like in an oxy-fuel combustion process. The advantages of using peroxy-fuels over hydrocarbons inside a model combustion chamber are also investigated with the help of CFD (Computational Fluid Dynamics) simulations. T2 - 25. Deutscher Flammentag - Verbrennung und Feuerung CY - Karlsruhe, Germany DA - 14.09.2011 KW - Organic peroxide KW - Peroxy-fuel KW - Burner concept KW - Combustion KW - Combustion chamber PY - 2011 SN - 978-3-18-092119-8 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte VL - 2119 SP - 307 EP - 312 PB - VDI-Verl. AN - OPUS4-24388 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schempp, Philipp A1 - Cross, Carl Edward A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - Grain Refinement of Aluminium Weld Metal through Inoculation with Titanium-Boron Master Alloy T2 - Euromat - European Conference on Advanced Materials and Processes CY - Montpellier, France DA - 2011-09-12 PY - 2011 AN - OPUS4-24389 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weber, Gert A1 - Brauser, Stephan A1 - Gaul, Holger A1 - Rethmeier, Michael T1 - Study of Fatigue Behaviour for Spot Welded Tensile Shear Specimens of Advanced High Strength Steels T2 - EUROMAT 2011 European Congress on Advanced Materials and Processes CY - Montpellier, France DA - 2011-09-12 PY - 2011 AN - OPUS4-24390 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Michael-Schulz, Heike T1 - Selbstzersetzliche Stoffe und selbsterhitzungsfähige Stoffe T2 - Einstufung physikalisch-chemischer Gefahren aus Sicht des Stoffrechts (UN-GHS/CLP) und des Transportrechts (UN-TDG) CY - Essen, Germany DA - 2011-09-27 PY - 2011 AN - OPUS4-24391 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bellon, Carsten A1 - Gollwitzer, Christian A1 - Fratzscher, Daniel A1 - Ewert, Uwe A1 - Jaenisch, Gerd-Rüdiger T1 - Simulation of complex scan paths for 3D reconstruction N2 - X-ray computed tomography (CT) is a volumetric (3D) Imaging diagnostic method, well established in the medical field, and in industrial NDE as well. Developments in industrial CT aim to extent the applicability to complex structures, which do not allow the access of all directions. This are e.g. limited view, data and angle CT applications. New reconstruction algorithms are required on one side, and the accuracy has to be improved on the other side. Numerical Simulation can support such developments by providing well defined data sets for the testing of reconstruction algorithms. This approach of virtual CT is realized within the radiographic simulator aRTist, developed by BAM. The poster shows the possibilities of this tool to consider complex scan paths. Simulated data sets have been reconstructed by an versatile backprojection algorithm. T2 - International symposium on digital industrial radiology and computed tomography CY - Berlin, Germany DA - 20.06.2011 KW - Radiographie KW - Computer-Simulation KW - 3D-Rekonstruktion PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-243928 SN - 978-3-940283-34-4 IS - DGZfP-BB 128 (Poster 17) SP - 1 EP - 4 PB - Deutsche Gesellschaft für zerstörungsfreie Prüfung e.V. (DGZfP) AN - OPUS4-24392 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN ED - Brückle, I. ED - Hahn, Oliver ED - Bredekamp, H. T1 - Galileo's sidereus nuncius - a comparison of the proof copy (New York) with other paradigmatic copies KW - BAM KW - Non-destructive testing KW - Archaeometry KW - X-ray fluorescence analysis PY - 2011 SN - 978-3-05-005095-9 VL - 1 SP - 1 EP - 188 PB - Akademie Verlag GmbH CY - Berlin AN - OPUS4-24394 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - BOOK A1 - Hahn, Oliver A1 - Czichos, Horst T1 - Was ist falsch am falschen Rembrandt - Mit High-Tech den Rätseln der Kunstgeschichte auf der Spur KW - ZfP KW - Archäometrie KW - Konservierung KW - Restaurierung KW - BAM PY - 2011 SN - 978-3-446-42636-8 SP - 1 EP - 223 PB - Carl Hanser Verlag CY - München AN - OPUS4-24395 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Kömmling, Anja A1 - Wachtendorf, Volker ED - Reichert, T. T1 - UV-LEDs - a new tool to determine the spectral response N2 - To determine a polymer’s spectral response of photo degradation, two main methods have been established. The so-called “filter technique” uses polychromatic radiation, which is filtered by a set of various sharp cut-on filters. This procedure provides separated reading points of an activation spectrum of the investigated material. With the "spectrographic technique” a specimen is irradiated with pectrally dispersed radiation, locally quasi monochromatically, and the local property changes.are related to the radiant exposure at the respective wavelengths. A third method, the irradiation of specimens with quasi monochromatic radiation behind interference filters, is rarely used. These methods have advantages and disadvantages and therefore, there are limits for conclusions from these spectral data. Concerning the quasi monochromatic Irradiation of specimens the development of new UV radiation sources looks promising. With the rapid development of inexpensive UV Light-emitting diodes (LEDs), new : sources of nearly monochromatic radiation in the UV ränge are available, even down to about 250 nm. To determine the spectral response, the use of such UV-LEDs in TO-18 ) and TO-39 metal cases combines the advantages of low cost and energy efficiency, stable spectral irradiance, temperature.and humidity control, larger specimen areas, and an easy and stable analysis. Combinations of different UV LEDs are also discussed as replacement for xenon arc ' radiation sources, see patent application EP01528388A1. T2 - 5th European weathering symposium - Natural and artificial ageing of polymers CY - Lisbon, Portugal DA - 21.09.2011 KW - UV resistance KW - Weathering KW - Spectral sensitivity KW - Action spectrum KW - UV-LEDs PY - 2011 SN - 978-3-9813136-2-8 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 15 SP - 77 EP - 86 PB - GUS (Gesellschaft für Umweltsimulation) CY - Pfinztal AN - OPUS4-24396 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Erfordert die Ersatzbaustoffverordnung neue Methoden des Abbruchs? T2 - BGRB-Kongress "Ressourcenschonung durch Baustoffrecycling" CY - Bonn, Germany DA - 2011-09-13 PY - 2011 AN - OPUS4-24397 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Masic, Admir A1 - Rabin, Ira A1 - Chierotti, M. R. A1 - Gobetto, R. A1 - Martra, G. A1 - Coluccia, S. A1 - Masic, A. T1 - Solid State and Unilateral NMR study og Deterioration of dead Sea scroll Fragments T2 - Technart 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-24278 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Fungal bioleaching of mineral components in a 20th-century illuminated parchment T2 - Technart 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-24279 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Archaeometry of the Dead Sea Scrolls T2 - SBL International Meeting CY - London, England DA - 2011-07-04 PY - 2011 AN - OPUS4-24280 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mix, Renate A1 - Friedrich, Jörg F. T1 - Improvement of Adhesivity of Polypropylene by Its Surface Modification Using the Aerosol Dielectric Barrier Discharge T2 - Adhesion '11, 11th International Conference on the Science and Technology of Adhesion and Adhesives CY - York, England DA - 2011-09-07 PY - 2011 AN - OPUS4-24283 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulte, Petra T1 - Physikalische Gefahren: Einstufungskriterien, Prüfmethoden, Vergleich mit Transportvorschriften T2 - Volkswagen Coaching Seminar: GHS Einstufung & Kennzeichnung (Basis) CY - Wolfsburg, Germany DA - 2011-08-30 PY - 2011 AN - OPUS4-24284 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kloß, Heinz A1 - Österle, Werner A1 - Dimitriev, A. T1 - Characterization of the mechanical wear behaviour by using simulation results of Movable Cellular Automata (MCA) method T2 - Int. Conf. on Physical Mesomechanics and Computer-Aided Design and Development of Advanced Materials CY - Tomsk, Russia DA - 2011-09-05 PY - 2011 AN - OPUS4-24287 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Lehmann, Jens A1 - Fischer, Joachim T1 - Neue Werkstoffe - Eigenschaften und Einsatzgrenzen T2 - MACH1 Weiterbildung - Neue Werkstoffe - Edelstahl Rostfrei CY - Herford, Germany DA - 2011-10-18 PY - 2011 AN - OPUS4-24318 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Lehmann, Jens A1 - Klapper, Helmuth Sarmiento A1 - Heyn, Andreas T1 - Untersuchungen des Einflusses der Oberflächenvorbehandlung auf die Korrosionsbeständigkeit hochlegierter Stähle mit Hilfe des elektrochemischen Rauschens T2 - 6. Workshop: Korrosionsdiagnostik und Korrosionsüberwachung mit Hilfe des elektrochemischen Rauschens CY - Magdeburg, Germany DA - 2011-09-14 PY - 2011 AN - OPUS4-24319 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Lehmann, Jens A1 - Burkert, Annette T1 - Alternative Edelstahlgüten zu den klassischen nichtrostenden Austeniten T2 - Kompetenzzentren Edelstahl-Rostfrei-Verarbeitung, Kursleiter-Fortbildung 2011 CY - Tuttlingen, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-24320 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Jaunich, Matthias A1 - Schulz, Sebastian A1 - Wolff, Dietmar T1 - Investigation the sealing behaviour of rubber seals at low temperatures T2 - 11. Schwarzheider Kunststoffkolloquium CY - Schwarzheide, Germany DA - 2011-09-21 PY - 2011 AN - OPUS4-24321 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Jaunich, Matthias A1 - Schulz, Sebastian A1 - Wolff, Dietmar T1 - Characterization of the low temperature behaviour of rubber sealing materials T2 - 22. Fachtagung TECHNOMER 2011 CY - Chemnitz, Germany DA - 2011-11-10 PY - 2011 AN - OPUS4-24322 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brauser, Stephan A1 - Kromm, Arne A1 - Dabah, Eitan A1 - Kannengießer, Thomas A1 - Rethmeier, Michael T1 - Thermal stability of retained austenite in low alloyed TRIP steel determined by high energy synchrotron diffraction T2 - Mecasens VI CY - Hamburg, Germany DA - 2011-09-07 PY - 2011 AN - OPUS4-24323 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gibmeier, J. A1 - Kromm, Arne A1 - Kannengießer, Thomas A1 - Altenkirch, J. T1 - Residual stress in steel fusion welds joined using low tranfsformation temperature (LTT) filler material T2 - Mecasens CY - Hamburg, Germany DA - 2011-09-07 PY - 2011 AN - OPUS4-24324 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Bredow, Andrea A1 - Berger, Wolfgang A1 - Wessel-Bothe, Stefan A1 - Keller, Toralf T1 - Optimierung des Säulenperkolationsverfahrens durch Automatisierung T2 - Jahrestagung der Deutschen Bodenkundlichen Gesellschaft CY - Berlin-Potsdam, Germany DA - 2011-09-03 PY - 2011 AN - OPUS4-24325 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Case study - "Phosphorus recovery from sewage sludge - Results of the European FP6 - and FP7 - projects SUSAN and SUSYPHOS" T2 - International Conference Environmental (Bio) Technologies & EU-FP7 Environment Brokerage Event CY - Gdansk, Poland DA - 2011-09-05 PY - 2011 AN - OPUS4-24327 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn A1 - Stegemann, B. A1 - Schüle, M. A1 - Schultz, C. A1 - Richter, M. A1 - Pahl, H.-U. A1 - Endert, H. A1 - Rau, B. A1 - Schlatmann, R. A1 - Quaschning, V. A1 - Fink, F. T1 - Novel Laser Structuring Method for Chalkopyrite Solar Cells T2 - Marie Sklodowska-Curie Symposium on the Foundations of Physical Chemistry CY - Warsaw, Poland DA - 2011-11-18 PY - 2011 AN - OPUS4-24920 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shcheglov, Pavel A1 - Gumenyuk, Andrey A1 - Gornushkin, Igor B. A1 - Rethmeier, Michael T1 - Experimental investigation of the laser-plume interaction during high power fiber laser welding N2 - The effect of the well-known plasma absorption and refraction in CO2-laser metal welding plumes is in case of high power solid state laser welding negligibly small. By contrast, the diffraction effects of shorter wavelength laser radiation are considerable. According to the results of preliminary studies, the fine condensed metal particles in the welding plume can lead to essential worsening of the laser beam quality. This work is devoted to the investigation of the lasermatter interaction during up to 20 kW ytterbium fiber laser welding of thick mild steel plates. The plume attenuation of a probe 1.3 µm wavelength diode laser beam as well as of continuous radiation in 250-600 nm wavelength range was measured during welding with and without Ar shielding gas supply. The measured results allow it to calculate average size and concentration of fine condensed metal particles in different plume areas using the multi-wavelength method and the Mie scattering theory. The plume temperature, which determines the condensation conditions, was measured by means of Fe I atom spectral line emission registration. The obtained results can be also of interest for remote metal treatment with high-power fiber or disc lasers. T2 - 30th ICALEO - International congress on applications of lasers & electro-optics CY - Orlando, FL, USA DA - 2011-10-23 PY - 2011 SN - 978-0-912035-94-9 SP - Paper 1606, 637 EP - 645 AN - OPUS4-24921 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan A1 - Kraft, B. A1 - Terborg, R. T1 - Performance Check of EDS X-Ray spectrometers - Extensions to high Count Rates T2 - PRORA 2011 Fachtagung Prozessnahe Röntgenanalytik CY - Berlin, Germany DA - 2011-11-24 PY - 2011 AN - OPUS4-24922 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Isecke, Bernd T1 - Materialuntersuchungen zur Bestimmung der Restlebensdauer von Massivbau T2 - Brückenertüchtigung - Beitrag zu einer leistungsfähigen Infrastruktur CY - Berlin, Germany DA - 2011-11-29 PY - 2011 AN - OPUS4-24923 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vattré, A. A1 - Fedelich, Bernard T1 - On the relationship between anisotropic yield strength and internal stresses in single crystal superalloys N2 - The present work focuses on the cubic slip phenomenon in single crystal superalloys with a high fraction of γ' precipitates at high temperature. The macroscopically apparent cubic slip mechanism is known to significantly reduce the tensile and creep strength of <1 1 1> oriented specimens. However, recent results obtained by 3D dislocation dynamics (Vattré et al., 2009) suggest a new interpretation of the so-called pseudo-cubic slip related to the nature of the dislocation network formation at the interfaces. These results are taken into account in a micromechanical model to improve the estimation of the strain hardening anisotropy. In accordance with the discrete simulations, it is shown that a key role is played by the combination of the activated octahedral slip systems as a function of the crystal orientation. In the <1 1 1> case, the contribution of the activated systems to kinematical hardening compensate, whereas strain hardening remains high for the <0 0 1> case. The experimental dependence of plastic flow on the orientation is also explained at the dislocation-scale mechanisms. Results are presented for the alloy CMSX-4 in several orientations. KW - Nickel-base superalloys KW - High-temperature deformation KW - Micromechanical modeling KW - Strengthening mechanisms PY - 2011 DO - https://doi.org/10.1016/j.mechmat.2011.07.007 SN - 0167-6636 SN - 1872-7743 VL - 43 IS - 12 SP - 930 EP - 951 PB - Elsevier CY - Amsterdam AN - OPUS4-24927 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miccoli, Lorenzo A1 - Perrone, C. A1 - Müller, Urs A1 - Gardei, André A1 - Ziegert, C. ED - Drochytka, R. ED - Bohus, S. T1 - Structural performances of earthen building materials. A comparison between different typologies N2 - Traditional construction techniques utilizing earthen materials are often seen as inferior compared to modern ways of building. Structural earthen elements are perceived as vulnerable towards environmental influences (moisture, frost) and in particular towards the load scenarios during earthquakes. In comparison to the recent advances in research on stone and brick masonry, knowledge on the structural performance of earthen building construction is limited and scattered. Consequently the confidence in the performance of these earthen buildings constructed in the traditional techniques during earthquakes is fairly low. The research presented here aims to make a comparison of mechanical behavior between different earth masonry material typologies, consisting of earth block masonry, rammed earth and cob. The paper has been developed in the framework of a larger research program called NIKER. BAM and other seventeen research partners from the Mediterrean area are jointly involved to develop and validate innovative materials and technologies for the systemic improvement of the seismic behavior of Cultural Heritage assets T2 - 2nd WTA - Internaitonal PhD Symposium - Building materials and buidling technology to preserve the built heritage CY - Brno, Czech Republic DA - 06.10.2011 KW - Earth masonry KW - Material test KW - Mechanical behavior KW - Cultural heritage PY - 2011 SN - 978-3-937066-21-9 SN - 0947-6830 N1 - Serientitel: WTA-Schriftenreihe – Series title: WTA-Schriftenreihe VL - 2 / Part 2 IS - 36 SP - 86 EP - 94 PB - WTA Publications AN - OPUS4-24928 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Teteris, Gundars A1 - Braun, Ulrike A1 - Bohmeyer, W. A1 - Lange, K. T1 - Kontrolle der Vernetzungsreaktion bei reaktiven Harzen - DSC, Rheologie, DMA, FTIR und Online-Ultraschall im Vergleich N2 - Faserverbundbauteile werden durch Tränkung von Fasergewebe mit flüssigem Harz, in der Regel Epoxidharzen, und anschließender Härtung des Harzes gefertigt. Dabei kann man das Gewebe im Vorfeld mit reaktivem Harz tränken und als so genanntes Prepreg verarbeiten oder man injiziert das frisch mit dem Härter gemischte Harz in ein Werkzeug, in dem das Gewebe bereits liegt - z. B. beim RTM-Prozess. Ausgehend von der Aufgabenstellung, eine Prepregherstellung mit hohem Qualitätsstandard zu realisieren und Möglichkeiten der Fertigungskontrolle für den Prepreg-Verarbeiter aufzuzeigen, wurde an einem für die Prepregherstellung vorgesehenen Harzsystem eine weitgehende Charakterisierung des Aushärtungsverlaufs vorgenommen. Wegen der Schwierigkeit, schnell konstante Aushärtungstemperaturen zu erreichen, wurden bei allen Methoden mit einer Heizrate von 1 K/min von RT bis 200 °C aufgeheizt. T2 - Technomer 2011 - 22. Fachtagung über Verarbeitung und Anwendung von Polymeren CY - Chemnitz, Deutschland DA - 10.11.2011 KW - Thermoanalyse KW - Lineare Aufheizung KW - Online Prozesskontrolle KW - Epoxidharz KW - Prepreg PY - 2011 SN - 978-3-939382-10-2 IS - Kap. 1.1 SP - 1 EP - 9 AN - OPUS4-24910 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Plarre, Rüdiger A1 - Krüger-Carstensen, B. T1 - An attempt to reconstruct the natural and cultural history of the webbing clothes moth Tineola bisselliella hummel (Lepidoptera: Tineidae) N2 - It is generally accepted that the natural habitats of most pest insects can be found outside the synanthropic environment in layers of leaf litter, under bark, as well as in rodent or bird nests. Indeed, most of the common pests have been reported as being facultative nidicolous. Therefore infestation of commodities by pest insects out of these reservoirs is one considerable possibility. However, the likelihood of a pest´s occurrence and survival out-doors largely depends on its ecological potential and competitiveness against other species of the same ecological guild. Some pest species are rarely found in wild habitats, especially in those regions where they are not native and where they have been introduced by man. The fabric pest Tineola bisselliella serves as a good example. Most likely originating in Central or Southern Africa this insect was introduced into Europe probably not earlier than the late 18th century. Being more tolerant to dry environments than other fabric pests its economical importance increased during the 20th century when in-door climates changed because of central heating systems. Its occurrence in out-door natural habitats must be regarded as accidental. Reported founds of webbing clothes moth larvae in bird nests e.g. have been largely overstated in the literature. T. bisselliella should be regarded as an eusynanthropic species KW - Evolution KW - Pest insect KW - Phylogeny KW - Synanthropy PY - 2011 SN - 2038-324X VL - 43 IS - 2 SP - 83 EP - 93 PB - DiPSA - Dipartimento di Protezione dei Sistemi Agroalimentare e Urbano e Valorizzazione delle Biodiv CY - Milano ET - Ser. II AN - OPUS4-24911 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger-Carstensen, B. A1 - Plarre, Rüdiger T1 - Outdoor trapping and genetical characterization of populations of the webbing clothes moth Tineola bisselliella (Lepidoptera: Tineidae) in the broader area of Berlin N2 - Adapted and effective pest management strategies for the protection of irreplaceable culture heritage as well as for the prevention of damages in households and warehouses are based on reliable information about the presence and distribution of the pest organisms. Monitoring the webbing clothes moth Tineola bisselliella at thirteen outdoor stations in the broader area of Berlin give a first idea of their occurrence in an urban area and the hinterlands. The results demonstrate a seasonal abundance in the city and a missing of this species in the countryside. Data suggest a synanthropic occurrence of the webbing clothes moth rather than an invasion from natural reservoires. Possible molecular examinations on the species and subspecies level are presented to analyze the gene flow between populations and give an impression of species mobility as well as pathways of infestation. KW - Infestation KW - Monitoring KW - Pheromone lures KW - Synanthropy PY - 2011 SN - 2038-324X VL - 43 IS - 2 SP - 129 EP - 135 PB - DiPSA - Dipartimento di Protezione dei Sistemi Agroalimentare e Urbano e Valorizzazione delle Biodiv CY - Milano ET - Ser. II AN - OPUS4-24912 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Molnarne, Maria A1 - Wilrich, Cordula A1 - Holtappels, Kai T1 - Chemically unstable gases and gas mixtures - new categories in the GHS N2 - In connection with the use of chemically unstable gases (especially acetylene and ethylene oxide) accidents keep on happening - amongst them also quite serious ones. These gases are known to be chemically unstable. A chemically unstable sas is a flammable gas that is able to react exolosivelv even in the absence of air or oxveen. The investigation of accidents showed that the Chemical instability of flammable gases played an important role in the severity of accidents. Therefore, this hazardous property was included in the global harmonizatiön of the Classification of Chemicals. The Classification of chemically unstable flammable gases and mixtures is an amendment to Chapter 2.2 “Flammable gases” of the UN Globally Harmonized System of Classification and Labelling of Chemicals (GHS), because most chemically unstable gases are flammable as well. The proposal to add them to the GHS originated from the experts of an informal working group of the UN Sub-Committee of Expert on the GHS (UNSCEGHS) headed by BAM, Germany. The UNSCEGHS has decided to include it in the Fourth Revised Edition of the GHS. The respective method for determining whether a gas is chemically unstable or not, is included in the UN Manual of Tests and Criteria. This paper presents some experimental investigations of these gases, the test methods, examples of new classifications and results from CHEMSAFE T2 - 14th Annual symposium, Mary Kay O´Connor process safety center - Beyond regulatory compliance: making safety second nature CY - College Station, TX, USA DA - 25.10.2011 KW - Chemically unstable gases KW - GHS KW - Chemisch instabile Gase PY - 2011 SP - 871 EP - 882 AN - OPUS4-24913 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nagamine, K. A1 - Reinsch, Stefan A1 - Müller, Ralf A1 - Honma, T. A1 - Komatsu, T. T1 - Crystallization behavior of lithium iron phosphate glass powders in different atmospheres N2 - Crystallization behavior in different atmospheres (air, Ar, and 7% H2/Ar) of lithium iron phosphate glass (33Li2O–33Fe2O3–1Nb2O5–33P2O5 (LFNP)) powders with different sizes of 2–1000 µm was examined. The crystallization peak temperature (Tp) in Ar and 7% H2/Ar decreased with decreasing the particle size of glass powders, but the value of Tp in air was independent of particle size. The crystallized glass obtained by heating to Tp showed the formation of the α-Li3Fe2(PO4)3 and LiFePO4 crystalline phases. Fe2O3 crystals were formed only in the inside of crystallized glass plates in the heating in air. The crystallization of LiFePO4 was largely enhanced in the particle size of <2 µm during the heating in Ar and 7% H2/Ar atmospheres. The main crystallization mechanism in LFNP glass was found to be surface crystallization. Significant shrinkages were observed for glass compacts (pellets) in the heating in 7% H2/Ar. These results suggest that controlling particle sizes and atmospheres enables the design the morphology of LiFePO4 crystals in LFNP glass. KW - DTA KW - Kristallisation KW - Phasenentwicklung KW - Unterschiedliche Atmosphären KW - Lithiumionen-Batterie PY - 2011 DO - https://doi.org/10.1111/j.1551-2916.2011.04579.x SN - 0002-7820 SN - 1551-2916 VL - 94 IS - 9 SP - 2890 EP - 2895 PB - Blackwell Publishing CY - Malden AN - OPUS4-24914 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Osterloh, Kurt A1 - Bücherl, T. A1 - Lierse von Gostomski, C. A1 - Zscherpel, Uwe A1 - Ewert, Uwe A1 - Bock, S. T1 - Filtering algorithm for dotted interferences N2 - An algorithm has been developed to remove reliably dotted interferences impairing the perceptibility of objects within a radiographic image. This particularly is a major challenge encountered with neutron radiographs collected at the NECTAR facility, Forschungs-Neutronenquelle Heinz Maier-Leibnitz (FRM II): the resulting images are dominated by features resembling a snow flurry. These artefacts are caused by scattered neutrons, gamma radiation, cosmic radiation, etc. all hitting the detector CCD directly in spite of a sophisticated shielding. This makes such images rather useless for further direct evaluations. One approach to resolve this problem of these random effects would be to collect a vast number of single images, to combine them appropriately and to process them with common image filtering procedures. However, it has been shown that, e.g. median filtering, depending on the kernel size in the plane and/or the number of single shots to be combined, is either insufficient or tends to blur sharp lined structures. This inevitably makes a visually controlled processing image by image unavoidable. Particularly in tomographic studies, it would be by far too tedious to treat each single projection by this way. Alternatively, it would be not only more comfortable but also in many cases the only reasonable approach to filter a stack of images in a batch procedure to get rid of the disturbing interferences. The algorithm presented here meets all these requirements. It reliably frees the images from the snowy pattern described above without the loss of fine structures and without a general blurring of the image. It consists of an iterative, within a batch procedure parameter free filtering algorithm aiming to eliminate the often complex interfering artefacts while leaving the original information untouched as far as possible. KW - Neutron KW - Radiography KW - Tomography KW - Filtering KW - Evaluation KW - NECTAR PY - 2011 DO - https://doi.org/10.1016/j.nima.2011.01.107 SN - 0168-9002 SN - 0167-5087 VL - 651 IS - 1 SP - 171 EP - 174 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-24917 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Osterloh, Kurt A1 - Fratzscher, Daniel A1 - Schwabe, A. A1 - Schillinger, B. A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Radiography and partial tomography of wood with thermal neutrons N2 - The effective high neutron scattering absorption coefficient of hydrogen (48.5 cm²/g) due to the scattering allows neutrons to reveal hydrocarbon structures with more contrast than X-rays, but at the same time limits the sample size and thickness that can be investigated. Many planar shaped objects, particularly wood samples, are sufficiently thin to allow thermal neutrons to transmit through the sample in a direction perpendicular to the planar face but not in a parallel direction, due to increased thickness. Often, this is an obstacle that prevents some tomographic reconstruction algorithms from obtaining desired results because of inadequate information or presence of distracting artifacts due to missing projections. This can be true for samples such as the distribution of glue in glulam (boards of wooden layers glued together), or the course of partially visible annual rings in trees where the features of interest are parallel to the planar surface of the sample. However, it should be possible to study these features by rotating the specimen within a limited angular range. In principle, this approach has been shown previously in a study with fast neutrons [2]. A study of this kind was performed at the Antares facility of FRM II in Garching with a 2.6×107/cm² s thermal neutron beam. The limit of penetration was determined for a wooden step wedge carved from a 2 cm×4 cm block of wood in comparison to other materials such as heavy metals and Lucite as specimens rich in hydrogen. The depth of the steps was 1 cm, the height 0.5 cm. The annual ring structures were clearly detectable up to 2 cm thickness. Wooden specimens, i.e. shivers, from a sunken old ship have been subjected to tomography. Not visible from the outside, clear radial structures have been found that are typical for certain kinds of wood. This insight was impaired in a case where the specimen had been soaked with ethylene glycol. In another large sample study, a planar board made of glulam has been studied to show the glued layers. This study shows not only the limits of penetration in wood but also demonstrates access to structures perpendicular to the surface in larger planar objects by tomography with fast neutrons, even with incomplete sets of projection data that covers an angular range of only 90° or even 60°. KW - Neutron computed tomography KW - Limited angle tomography KW - Wood KW - Annual rings PY - 2011 DO - https://doi.org/10.1016/j.nima.2011.02.095 SN - 0168-9002 SN - 0167-5087 VL - 651 IS - 1 SP - 236 EP - 239 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-24918 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hennecke, Manfred T1 - Ressortforschung und Politikberatung N2 - Fast allen deutschen Bundesministerien sind Einrichtungen zugeordnet, die sie in der Erfüllung von Bundesaufgaben auf wissenschaftlicher Grundlage unterstützen. Die Vielfalt sowie die Art und der jeweilige Anteil der Aufgaben (insbesondere der Anteil der Forschung) haben dazu geführt, das es sehr unterschiedliche Typen von Ressortforschungseinrichtungen gibt. Viele dieser Einrichtungen erbringen in bedeutendem Umfang Dienstleistungen für Wirtschaft, Wissenschaft und Gesellschaft; alle stehen den Ministerien für Beratungsaufgaben unmittelbar zur Verfügung. Ihre Kompetenz stützt sich ganz wesentlich auf Forschung und Entwicklung und unterscheidet sie dadurch von anderen Bundesbehörden. PY - 2011 SN - 0303-2493 IS - 7/8 SP - 391 EP - 395 PB - BBSR CY - Bonn AN - OPUS4-24919 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kuchenbecker, Petra A1 - Güther, Wolfgang A1 - Rabe, Torsten T1 - Mechanische und thermomechanische Charakterisierung von grünen Folien und Laminaten T2 - DKG/DGM Symposium "Charakterisierungsverfahren in der keramischen Aufbereitung: Vom Pulver bis zum Grünkörper" CY - Erlangen, Germany DA - 2011-11-29 PY - 2011 AN - OPUS4-24869 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feigl, Michael A1 - Zietelmann, Christina A1 - Sabel, Martin A1 - Nofz, Marianne T1 - Electrochemical evaluation of corrosion behaviour of sol-gel alumina coated steel AlSl304 and Ni-base alloy Inconel-718 T2 - Eurocorr 2011 CY - Stockholm, Sweden DA - 05.09.2011 PY - 2011 AN - OPUS4-24870 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Steinborn, Gabriele A1 - Wäsche, Rolf A1 - Tzschichholz, Grit T1 - Tribologisches Verhalten von heiß-isostatisch gepresstem Yttriumtitanat unter oszillierender Gleitbeanspruchung T2 - HLK 2011 CY - Karlsruhe, Germany DA - 2011-10-25 PY - 2011 AN - OPUS4-24872 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dietrich, Paul A1 - Horlacher, T. A1 - Girard-Lauriault, Pierre-Luc A1 - Gross, Thomas A1 - Lippitz, Andreas A1 - Min, Hyegeun A1 - Wirth, Thomas A1 - Castelli, R. A1 - Seeberger, P. A1 - Unger, Wolfgang T1 - Multimethod chemical characterization of carbohydrate-functionalized surfaces N2 - A combined XPS, NEXAFS, and ToF-SIMS chemical surface characterization of carbohydrate-functionalized gold and glass surfaces is presented. Spot shape and chemical composition across a spot surface are provided by surface-sensitive methods as ToF-SIMS and XPS, used in their imaging modes. Moreover, the feasibility of this multimethod approach to control relevant production steps of a carbohydrate microarray prototype is demonstrated. KW - Carbohydrates KW - Microarrays KW - Self-assembled monolayers KW - XPS KW - NEXAFS KW - ToF-SIMS PY - 2011 DO - https://doi.org/10.1080/07328303.2011.615181 SN - 0732-8303 VL - 30 IS - 4-6 SP - 361 EP - 372 PB - Taylor & Francis CY - London [u.a.] AN - OPUS4-24874 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Schulze, M. A1 - Staude, Andreas A1 - Neukamm, M. A1 - Neuschaefer-Rube, U. A1 - Goebbels, Jürgen A1 - Bartscher, M. A1 - Bellon, Carsten A1 - Hilpert, U. ED - Weckenmann, A. T1 - Hochgenaue Geometriebestimmung von Mikrobauteilen mit Computertomographie (CT) N2 - Ziel des Vorhabens ist die hochgenaue und vollständige Erfassung innerer und äußerer Geometrien von Mikrobauteilen mittels Mikro-Computertomographie (µCT). Industriell wichtige Mikrobauteile sind z.B. Einspritzsysteme, Festplattenkomponenten oder Instrumente für die minimal-invasive Chirurgie. Typische Bauteilgrößen liegen hier im Bereich 0,1 mm - 100mm; typische zu messende Strukturen haben Größen von 0,5 µm - 500 µm. Mit klassischen Methoden der Messtechnik ist eine schnelle und hochgenaue Erfassung der gesamten Oberfläche von Mikrobauteilen bisher kaum möglich. Innenstrukturen von Mikrobauteilen können mit keiner optischen oder taktilen Messtechnik zerstörungsfrei gemessen werden. Diese Einschränkungen sollen mittels hochgenauer µCT überwunden werden. Hierzu soll der Messprozess simuliert werden, um die Anwendung von Korrekturverfahren zur Genauigkeitssteigerung zu ermöglichen. CT-Messungen an kalibrierten Mikroprüfkörpern sollen die Korrekturverfahren verifizieren. Für die Kalibrierung der Prüfkörper sollen Multisensor-Verfahren entwickelt und getestet werden. Diese sollen es erlauben, Prüfkörper gleichzeitig hochgenau und mit großer Messpunktdichte zu kalibrieren. Es ist geplant, die an Prüfkörpern erreichten Messunsicherheiten und Auflösungen zum Projektabschluss an realen, industriellen Mikrobauteilen (z.B. Mikrozahnrädern) messtechnisch nachzuweisen. T2 - Abschlusskolloquium DFG Schwerpunktprogramm 1159 - Neue Strategien der Mess- und Prüftechnik für die Produktion von Mikrosystemen und Nanostrukturen CY - Erlangen, Deutschland DA - 06.10.2010 PY - 2011 SN - 978-3-8440-0358-1 SN - 0945-0769 SP - 36 EP - 52 PB - Shaker Verlag GmbH AN - OPUS4-24875 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Zimmermann, J. A1 - Sawodny, O. A1 - Lyda, W. A1 - Burla, A. A1 - Osten, W. A1 - Eigenbrod, H. A1 - Westkämper, E. A1 - Shaw, L. A1 - Weckenmann, A. A1 - Herffurth, T. A1 - Duparré, A. A1 - Tünnermann, A. A1 - Staude, Andreas A1 - Goebbels, Jürgen ED - Weckenmann, A. T1 - Registrierung multimodaler Messungen am Beispiel eines MEMS N2 - Die Produktion von elektronischen, optischen und elektro-mechanischen Mikro- und Nanosystemen stellt hohe Anforderungen an die Messtechnik, um die Fertigungsprozesse zu optimieren und die Qualität zu prüfen. Existierende Messverfahren unterliegen Beschränkungen hinsichtlich des Auflösungsvermögens, der Messfeldgröße und des Ergebnisses der Messung. Der kombinierte Einsatz von Sensoren mit unterschiedlichen Fähigkeiten in den Auflösungsstufen mittels einer intelligenten Messstrategie ermöglicht eine effiziente Prüfung. Neben den geeigneten Prüfstrategien werden auch Methoden zur Fusion und Auswertung der Daten von Sensoren mit unterschiedlichen Auflösungsfähigkeiten benötigt. Datenfusion bezeichnet dabei das Zusammenfügen verschiedener Messungen, um entweder unterschiedliche Eigenschaften eines Messobjekts in einem gemeinsamen Koordinatensystem angeben zu können oder um aus verschiedenen Messungen derselben Eigenschaft des Messobjekts einen Datensatz von höherer Qualität gegenüber den einzelnen Datensätzen zu erhalten. Voraussetzung für die Datenfusion ist Registrierung, die eine Überführung von Messdaten unterschiedlicher Messfelder oder Messmittel in ein gemeinsames Koordinatensystem darstellt und Thema dieses Beitrages ist. T2 - Abschlusskolloquium DFG Schwerpunktprogramm 1159 - Neue Strategien der Mess- und Prüftechnik für die Produktion von Mikrosystemen und Nanostrukturen CY - Erlangen, Deutschland DA - 06.11.2010 PY - 2011 SN - 978-3-8440-0358-1 SN - 0945-0769 SP - 173 EP - 187 PB - Shaker Verlag GmbH AN - OPUS4-24876 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Neuschaefer-Rube, U. A1 - Becke, C. A1 - Sadowski, E. A1 - Tan, Ö. A1 - Staude, Andreas A1 - Zimmermann, J. ED - Weckenmann, A. T1 - Virtuelle Messgeräte und Simulationen im Mikrobereich - Potential und Grenzen T2 - Abschlusskolloquium DFG Schwerpunktprogramm 1159 - Neue Strategien der Mess- und Prüftechnik für die Produktion von Mikrosystemen und Nanostrukturen CY - Erlangen, Deutschland DA - 2010-10-06 PY - 2011 SN - 978-3-8440-0358-1 SN - 0945-0769 SP - 206 EP - 218 PB - Shaker Verlag GmbH AN - OPUS4-24877 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Urs A1 - Schlegel, Moritz-Caspar A1 - Emmerling, Franziska T1 - Advanced techniques for studying damage mechanisms of cementitious matrices affected by sulfate attack N2 - Cementitious materials, in particular concrete, are durable materials if prepared appropriately and the Service life of concrete structures is now often required to last 120 years or more. Concrete durability depends strongly on intrinsic (e.g. composition, porosity) and exterior factors (e.g. moisture condition and composition, frost cycles, load pattem). Deleterious actions leading to concrete degradation are often created by the environment. Extemal sulfate attack is one of the more spectacular damage scenarios for concrete structures caused by the ingress of sulfate ions into the pore System of the material and successive formation of expanding phases. Though in recent years well studied there are still many questions remaining conceming the mechanisms of sulfate attack. In particular over the last ten years, with the increased utilization of blended cements, new questions arose concerning the sulfate resistance of those binder Systems. In the presented study therefore a method was developed to analyze the changes of the phase composition within the micro structure due to sulfate attack. The analytical method was based on pX-Ray diffraction (pXRD) using Synchrotron radiation in Debye-Scherrer (transmission) geometry. The spatial resolution of the method is ca. 10 pm and allows the characterization of phase transformations in the wake of damaging processes in more detail compared to other techniques. Furthermore, the experimental setup provides the possibility for analyzing the phase assemblage of a given sample without destroying the micro structure. This is possible because the specimens for phase analysis consists of thick sections, which can be used for further microscopic analysis of the micro structure and micro chemistry (e.g. by SEM-EDX). Samples containing supplementary cementitious materials were measured in comparison and to reconstruct the influence of the degradation process in detail. Additionally, reaction ffonts within the samples were localized by micro x-ray fluorescence analysis (MXRF). T2 - EMABM 2011 - 13th Euroseminar on microscopy applied to building materials CY - Ljubljana, Slovenia DA - 14.06.2011 KW - Sulfate attack KW - Concrete KW - Synchrotron KW - XRD KW - Phase analysis PY - 2011 SN - 978-961-90366-7-9 SP - 1 EP - 9 AN - OPUS4-24878 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gornushkin, Igor B. A1 - Shabanov, Sergej V. A1 - Merk, Sven T1 - Interplay between Diagnostic and Modeling in Laser Induced Breakdown Spectroscopy T2 - CSI37 - Colloquium Spectroscopicum Internatione XXXVII CY - Búzios, Brazil DA - 2011-08-28 PY - 2011 AN - OPUS4-24879 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feistkorn, Sascha A1 - Taffe, Alexander T1 - Die POD - eine Vorgehensweise zum qualitativen Gütenachweis zerstörungsfreier Prüfverfahren im Bauwesen am Beispiel des Impulsradars N2 - Die POD (Probability of Detection) hat sich als statistisches Werkzeug für die Bewertung der Zuverlässigkeit zerstörungsfreier Prüfsysteme in der klassischen ZfP bewährt. Aus diesem Grund wird die Methode der POD auf die zerstörungsfreie Prüfung im Bauwesen übertragen, um erstmals eine objektive Antwort auf zerstörungsfreie Prüfungen geben zu können, denen eine qualitative Fragestellung zugrunde liegt. Dies geschieht an der Prüfaufgabe der Ortung metallischer Reflektoren in Abhängigkeit Ihrer Tiefenlage mithilfe des Impulsradars. Dazu wird nachgewiesen, dass eine Übertragung und Anwendung der POD für die objektive Bewertung dieser Prüfaufgabe zulässig ist. Nach der Konzipierung und Fertigung von Testkörpern werden die Ergebnisse der POD(a)-Analyse vorgestellt, die erstmal eine Charakterisierung und einen Vergleich unterschiedlicher Radarprüfsysteme anhand eines objektiv ermittelten Kennwerts ermöglichen. Außerdem können Einflussgrößen auf die Detektionstiefe eines metallischen Reflektors erstmals quantifiziert werden. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Impulsradar KW - Probability of detection KW - POD KW - ZfPBau KW - Gütenachweis KW - Qualitative Prüfaufgabe PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-248866 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 SP - 1 EP - 9 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-24886 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ehrig, Karsten A1 - Bartscher, M. A1 - Goebbels, Jürgen A1 - Koch, M. A1 - Staude, Andreas T1 - Einfluss von Materialkombinationen auf das dimensionelle Messen mit Mikro-Computertomographie am Beispiel eines werkstücknahen Testkörpers N2 - Die Computertomographie (CT) hat sich als dimensionelle Messmethode in der industriellen Produktion etabliert. Durch Messungen an speziellen Prüfkörpern ist es möglich, quantitative Informationen über die metrologischen Eigenschaften dimensioneller Messungen zu erhalten. In dieser Arbeit wird einen Aluminium-Guss-Prüfkörper (120 mm x 90 mm x 60 mm) benutzt, mit dem – in der vorliegender Form – auch der Einfluss von Materialien unterschiedlicher Schwächung auf dimensionelle CT-Messungen untersucht werden kann. Der Prüfkörper ist in vier Segmente zerteilt, so dass auch innenliegende, raue Gussfreiformflächen der taktilen Koordinatenmessung zugänglich sind. Durch adaptierte Rubinkugeln als Referenzstrukturen können die CT-Messdaten in taktile Referenz-Koordinatensysteme überführt werden. Um den Einfluss von Materialien unterschiedlicher Schwächung auf das dimensionelle Messen mit CT zu untersuchen, wurden stärker schwächende ZTA-Störkugeln (Zirconia Toughened Alumina) mit zur Ausrichtung geeigneter Symmetriebrechung in der Nähe von ausgewählten taktilen Messstellen angebracht. Zur Bewertung der Messabweichungen dienen taktile Referenzmessungen an den ZTA-Kugeln sowie taktile Messungen an den Freiformflächen des Gussteils, wobei durch ein iteratives Antastverfahren eine verbesserte Erfassung der Geometrie auch bei starken lokalen Oberflächenkrümmungen sichergestellt wird. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Mikro-CT KW - Dimensionelles Messen KW - Testkörper KW - Multimaterial PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-248878 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Di.1.B.2) SP - 1 EP - 6 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-24887 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Drescher, Daniela A1 - Laube, G. A1 - Schneider, G. A1 - Guttmann, P. T1 - Combination of SERS and advanced microscopic methods for the investigation of protein-particle-cell interactions T2 - Workshop "FT-IR Spectroscopy in Microbiological and Medical Diagnostics" CY - Berlin, Germany DA - 2011-10-20 PY - 2011 AN - OPUS4-24888 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachsmuth, Janne A1 - Bohse, Jürgen T1 - Schallemissionsanalyse von Schadensmechanismen an Feinkornstahl N2 - In dieser Arbeit werden geschweißte Platten aus dem Feinkornstahl P460NL1 untersucht. Korrosion und Ermüdungsrisswachstum werden als Schadensmechanismen in das Material eingebracht und auf ihre Nachweisbarkeit in Plattenversuchen geprüft. Die Schallemissionssignale wurden nach primären und sekundären Quellmechanismen getrennt und ihr Einfluss auf die Gesamtemission analysiert. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-248902 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Di.2.C.2) SP - 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-24890 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ortwein, Hans-Peter A1 - Bohse, Jürgen A1 - Trappe, Volker A1 - Hickmann, Stefan T1 - Untersuchung des Zwischenfaserrisswachstums in Faserverbundwerkstoffen mit Schallemissions- und Röntgenrefraktionsverfahren N2 - Hinsichtlich Materialermüdung und Betriebsfestigkeit in Faserkunststoffverbunden besteht - verglichen mit anderen Aspekten des Faserverbundleichtbaues – noch erheblicher Forschungsbedarf. Schon weit vor den globalen Festigkeiten des Laminates treten eine Vielzahl von Zwischenfaserbrüchen und vereinzelte Faserbrüche auf. Die Dichte dieser Mikrorisse soll hier als Indikator für den Zustand des Verbundes genutzt werden. Ihre Ermittlung stellt insbesondere bei Kohlenstofffasern eine Herausforderung dar. Über vergleichende Messungen mit der Schallemissionsanalyse (SEA) und der Röntgenrefraktionsscans (RR) wird die Entwicklung der Rissdichte bei Belastung untersucht. Die SEA zeichnet die Entstehung der Risse auf und kann wegen der kompakten Messtechnik auch gut am Bauteil eingesetzt werden. Die RR beobachtet die Änderung der inneren Grenzflächen, die ebenfalls die Entwicklung der Rissdichte widerspiegelt. Sie ist allerdings zurzeit nur als Laborverfahren geeignet. Der Vortrag berichtet(e) über den aktuellen Stand des vergleichenden Einsatzes beider Verfahren an Flachproben und innendruckbelasteten Rohrproben. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Deutschland DA - 30.05.2011 KW - Schallemissionsprüfung KW - Röntgenrefraktionsmessung KW - Faserkunstoffverbund KW - Druckbehälter PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-248913 SN - 978-3-940283-33-7 SP - Mi.4.A.1 - 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-24891 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ortwein, Hans-Peter A1 - Bohse, Jürgen A1 - Trappe, Volker T1 - Untersuchung der Mikrorissbildung in Faserkunststoffverbunden mittels Röntgenrefraktions- und Schallemissionsmessung N2 - Hinsichtlich Materialermüdung in Faserkunststoffverbunden besteht verglichen mit anderen Aspekten des Faserverbundleichtbaues – noch erheblicher Forschungsbedarf. Schon weit vor den globalen Festigkeiten des Laminates treten eine Vielzahl von Zwischenfaserbrüchen und vereinzelte Faserbrüche auf. Die Dichte dieser Mikrorisse soll als Indikator für den Zustand des Verbundes genutzt werden. Ihre Ermittlung stellt insbesondere bei Kohlenstofffasern eine Herausforderung dar. Über vergleichende Messungen mit der Schallemissionsanalyse (SEA) und der Röntgenrefraktionsanalyse (RR) wird die Entwicklung der Rissdichte bei Belastung untersucht. die SEA zeichnet die Entstehung der Risse auf und kann wegen der kompakten Messtechnik auch gut am Bauteil eingesetzt werden Die RR beobachtet die Änderung der inneren Grenzflächen, die ebenfalls eine Entwicklung der Rissdichte widerspiegelt. Sie ist allerdings zurzeit nur als Laborverfahren geeignet. Der Vortrag berichtet über den aktuellen Stand des vergleichenden Einsatzes beider Verfahren an Zugproben und Modellbehältern. T2 - 18. Kolloquium Schallemission CY - Wetzlar, Deutschland DA - 27.10.2011 KW - Schallemissionsprüfung KW - Röntgenrefraktionsmessung KW - Faserkunststoffverbund KW - Druckbehälter PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-248926 SN - 978-3-940283-37-5 VL - 131 SP - V05-1 EP - 7 AN - OPUS4-24892 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg A1 - Symietz, Christian A1 - Lehmann, Erhard A1 - Gildenhaar, Renate A1 - Berger, Georg T1 - Fixation of bioactive calcium phosphate on Ti6AI4V with e femtosecond laser T2 - Jahrestagung der Deutschen Gesellschaft für Biomaterialien (DGBM) CY - Giessen, Germany DA - 2011-11-10 PY - 2011 AN - OPUS4-24893 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiggenhauser, Herbert T1 - Non-Destructive Testing in Civil Engineering T2 - SVTI-Workshop "ZfP für Betonbauteile in Kernkraftwerken" CY - Zurich, Switzerland DA - 2011-11-16 PY - 2011 AN - OPUS4-24895 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Explosionsgefahr durch mechanisch erzeugte Funken T2 - 12. Essener Brandschutztage Veranst.-Nr.: E-H050-11-490-1 CY - Aachen, Germany DA - 2011-11-23 PY - 2011 AN - OPUS4-24896 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Lehmann, Jens T1 - Alternative Edelstahlgüten zu den klassischen nichtrostenden Austeniten T2 - Sitzung des Ausschusses Marketing der Informationsstelle Edelstahl Rostfrei CY - Düsseldorf, Germany DA - 2011-11-24 PY - 2011 AN - OPUS4-24897 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Menrad, Andreas A1 - Goedecke, Thomas T1 - Einflussfaktoren auf die Innendruckprüfung: Elastizitätsmodul und Zeitstandverhalten T2 - Erfahrungsaustausch AK-Inspektionsstellen CY - Berlin, Germany DA - 2011-09-28 PY - 2011 AN - OPUS4-24898 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Menrad, Andreas A1 - Goedecke, Thomas T1 - Der Zusammenhang der Innendruckprüfung mit dem Elastizitätsmodul und dem Zeitstandverhalten T2 - Erfahrungsaustausch AK-Prüfstellen CY - Berlin, Germany DA - 2011-11-23 PY - 2011 AN - OPUS4-24899 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liehr, Sascha A1 - Krebber, Katerina T1 - A dynamic fiber optic strain and power change sensor N2 - A dynamic and quasi-distributed sensor principle for simultaneous measurement of length changes and optical power changes between reflection points in an optical fiber is presented. The technique is based on the incoherent optical frequency domain reflectometry (I-OFDR). The calculation of phase and amplitude changes from few measurement points in the frequency domain yields precise and dynamic length and optical power change results up to 2 kHz and μm-resolution. Test results showing the deformation of a masonry building under seismic load are presented. Promising fields of application for this technique are the structural health monitoring sector and chemical process control. T2 - 21st International Conference on Optical Fiber Sensors CY - Ottawa, Canada DA - 15.05.2011 PY - 2011 AN - OPUS4-24930 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ortwein, Hans-Peter A1 - Trappe, Volker A1 - Bohse, Jürgen A1 - Hickmann, Stefan ED - Grellmann, W. T1 - In-Situ-Messung der Matrixschädigung in kohlenstofffaserverstärktem Kunststoff unter uni- und biaxialer Zugbelastung N2 - Die Restlebensdauerabschätzung von Faserkunststoffverbunden ist ein ungelöstes Problem. Die Beobachtung der Matrixschädigung ist dabei ein vielversprechender Ansatz zur Bewertung des Schädigungszustandes insgesamt. Unter kombinierter Beobachtung mit Röntgenrefraktionsmessungen und Schallemissionsmessung wurden uni- und biaxiale Lasten statisch und zyklisch auf Kohlenstofffaserepoxidharz-Proben aufgebracht. Die uniaxiale Belastung erfolgt mittels einer eigenentwickelten Kompaktprüfmaschine direkt während der Röntgenrefraktions- und Schallemissionsmessung in der Röntgenkammer. Die biaxiale Belastung wird an Modelldruckbehältern ebenfalls mit Schallemissionsmessung durchgeführt. Hier wird der Modelldruckbehälter mit dem Röntgenrefraktionsverfahren periodisch inspiziert. T2 - DVM-Tagung Werkstoffprüfung 2011 - Neue Entwicklungen in der Werkstoffprüfung - Herausforderungen an die Kennwertermittlung CY - Berlin, Germany DA - 01.12.2011 KW - Druckbehälterprüfung KW - CFK KW - Schallemissionsmessung KW - Röntgenrefraktionsmessung KW - Matrixschädigung KW - Faserkunststoffverbund KW - Druckbehälter PY - 2011 SN - 978-3-9814516-1-0 SN - 1861-8154 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 643 SP - 161 EP - 166 AN - OPUS4-24931 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häcker, Ralf A1 - Klinger, Christian A1 - Kahlcke, Ole A1 - Schriever, Sina ED - Grellmann, W. T1 - Zwischen Zeitstand und Relaxation - Einfluss der Proben- und Prüfmaschinensteifigkeit auf die Lebensdauer unter konstanter Belastung N2 - Zur Abschätzung der Lebensdauer eines bei höherer Temperatur langzeitbelasteten Bauteils wurden Zeitstandversuche, Relaxationsversuche und weitere Versuche mit unterschiedlichen Umgebungssteifigkeiten durchgeführt. Die Zeitstandversuche, deren Versuchsführung eine unendlich niedrige Umgebungssteifigkeit simuliert, liefern geringere Lebensdauern (Bruchzeiten) im Vergleich zu Versuchen mit endlich hohen, technisch relevanten Steifigkeiten bei vergleichbarer Probensteifigkeit (Geometrie), wobei die Lebensdauern mit steigender Umgebungssteifigkeit zunehmen. Die längsten Lebensdauern zeigen Relaxationsversuche mit einer unendlich hohen Umgebungssteifigkeit aufgrund ihrer Versuchsregelung. Für die Übertragung der an Proben gewonnenen Ergebnisse auf das Bauteil wurde das Steifigkeitsverhältnis Z zwischen der Steifigkeit der 'Probe' und der der 'Umgebung' definiert und angewandt. Das Steifigkeitsverhältnis des kritischen Bereichs im Bauteil und das der Werkstoffprobe in der Prüfmaschine sollten möglichst ähnlich sein. Dann lassen sich bei der Übertragung auf das Bauteil realistisch höhere Lebensdauern abschätzen als nur mit Kenntnis der Ergebnisse der Zeit-standversuche. T2 - DVM-Tagung Werkstoffprüfung 2011 - Neue Entwicklungen in der Werkstoffprüfung - Herausforderungen an die Kennwertermittlung CY - Berlin, Germany DA - 01.12.2011 KW - Zeitstandverhalten KW - Steifigkeit KW - Relaxationsversuch KW - Lebensdauer KW - Bauteilprüfung PY - 2011 SN - 978-3-9814516-1-0 SN - 1861-8154 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 643 SP - 267 EP - 272 AN - OPUS4-24932 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witt, Jens A1 - Schukar, Marcus A1 - Krebber, Katerina A1 - Demuth, J. A1 - Sasek, L. T1 - Heart rate sensor for integration into personal protective equipment T2 - 20th International Conference on Plastic Optical Fibers CY - Bilbao, Spain DA - 2011-09-14 PY - 2011 AN - OPUS4-24934 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bleul, Regina A1 - Braun, Ulrike A1 - Bertin, Annabelle A1 - Maskos, Michael T1 - Polymers in Biomedicine: Molecular Structure and Material Charakteristics T2 - Jahrestagung Deutsche Gesellschaft für Biomaterialien CY - Giessen, Germany DA - 2011-11-10 PY - 2011 AN - OPUS4-24935 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhning, Martin A1 - Jaunich, Matthias A1 - Braun, Ulrike A1 - Stark, Wolfgang T1 - Curing behavior of EVA-based encapsulants for photovoltaic applications T2 - 11. Schwarzheider Kunststoffkolloquium CY - Schwarzheide, Germany DA - 2011-09-21 PY - 2011 AN - OPUS4-24936 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witt, Jens A1 - Breithaupt, Mathias A1 - Müller, Bernd R. A1 - Krebber, Katerina T1 - MPOF LPGs as radiation sensors T2 - 20th International Conference on Plastic Optical Fibers CY - Bilbao, Spain DA - 2011-09-14 PY - 2011 AN - OPUS4-24937 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lenke, Philipp A1 - Krebber, Katerina T1 - Verteilte und polymeroptische Fasersensorik T2 - Innovative und kostengünstige Sensoren aus dem Bereich der Polymer-Optischen Fasern CY - Wernigerode, Germany DA - 2011-11-15 PY - 2011 AN - OPUS4-24938 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krebber, Katerina T1 - Polymer Optical Fibres in Sensing - Applications & Future Demands T2 - IEEE Sensors 2011 Conference CY - Limerick, Ireland DA - 2011-10-28 PY - 2011 AN - OPUS4-24939 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bräutigam, P. A1 - Schneider, Rudolf A1 - Franke, M. A1 - Stolle, A. A1 - Ondruschka, B. T1 - Degradation of the antiepileptic drug carbamazepine by hydrodynamic-acoustic-cavitation T2 - GPE 2011 Malaysia - 3rd International Congress on Green Process Engineering CY - Kuala Lumpur, Malaysia DA - 2011-12-06 PY - 2011 AN - OPUS4-24951 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachsmuth, Janne A1 - Bohse, Jürgen ED - Grellmann, W. T1 - Nachweis von Korrosion und Ermüdungsrissen mittels Schallemission T2 - DVM-Tagung Werkstoffprüfung 2011 - Neue Entwicklungen in der Werkstoffprüfung - Herausforderungen an die Kennwertermittlung CY - Berlin, Deutschland DA - 2011-12-01 KW - Schallemissionsprüfung KW - Ermüdungsrisswachstum KW - Korrosion PY - 2011 SN - 978-3-9814516-1-0 SN - 1861-8154 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 643 SP - 213 EP - 218 AN - OPUS4-24953 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Umsetzung der ErP-Richtlinie und aktuelle Entwicklungen in Deutschland T2 - Fraunhofer IPA ExpertenForum CY - Stuttgart, Germany DA - 2011-12-06 PY - 2011 AN - OPUS4-24955 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Subaric-Leitis, Andreas T1 - Messunsicherheitsbestimmung in der Praxis T2 - Werkstofftechnisches Kolloquium der TU Darmstadt CY - Darmstadt, Germany DA - 2011-09-29 PY - 2011 AN - OPUS4-24956 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Subaric-Leitis, Andreas A1 - Brauser, Stephan A1 - Ullner, C. T1 - Bestimmung lokaler Spannungsdehnungskurven an Widerstandsschweißverbindungen mittels instrumentierter Krafteindringprüfung T2 - Fachausschuss FA-12 der AWT und des Arbeitskreises Härteprüfung der DGM CY - Wiesbaden, Germany DA - 2011-10-12 PY - 2011 AN - OPUS4-24957 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Subaric-Leitis, Andreas T1 - Aspekte der Ergebnisunsicherheit im Prüfwesen T2 - 260. PTB-Seminar: Berechnung der Messunsicherheit - Empfehlungen für die Praxis CY - Berlin, Germany DA - 2011-03-21 PY - 2011 AN - OPUS4-24958 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Subaric-Leitis, Andreas T1 - Aspekte der Messunsicherheitsbestimmung in der Härteprüfung T2 - 5. Zwick-Roell-Härte-Symposium CY - Ulm, Germany DA - 2011-07-05 PY - 2011 AN - OPUS4-24959 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Teteris, Gundars A1 - Bohmeyer, W. A1 - Lange, K. T1 - Kontrolle der Vernetzungsreaktion bei reaktiven Harzen - DSC, Rheologie, DMA, FTIR und Online-Ultraschall im Vergleich T2 - Technomer - 22. Fachtagung über Verarbeitung und Anwendung von Polymeren CY - Chemnitz, Germany DA - 2011-11-10 PY - 2011 AN - OPUS4-24900 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Falkenberg, Rainer T1 - Hydrogen Assisted Cracking: Mechanisms and coupling phenomena T2 - 7th Meeting of the TC2 on Micromechanisms of the European Structural Integrity Society CY - Berlin, Germany DA - 2011-11-24 PY - 2011 AN - OPUS4-24901 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Skrotzki, Birgit A1 - Brookes, S. A1 - Kühn, Hans-Joachim A1 - Sievert, Rainer A1 - Klingelhöffer, Hellmuth T1 - Axial-Torsional Thermo-Mechanical Fatigue of a near-Gamma TiAl-Alloy T2 - 4th International Workshop on Titanium Aluminides CY - Nuremberg, Germany DA - 2011-09-13 PY - 2011 AN - OPUS4-24902 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Bernd R. A1 - Lange, Axel A1 - Harwardt, Michael T1 - Synchrotron based refraction enhanced micro-CT for non-destructive characterisation of biological materials T2 - EUROMAT 2011 European Congress and Exhibition on Advanced Materials and Processes CY - Montpellier, France DA - 2011-09-12 PY - 2011 AN - OPUS4-24903 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Skrotzki, Birgit A1 - Kühn, Hans-Joachim T1 - Kennwertermittlung aus statischen und zyklischen Versuchen bei erhöhter Temperatur unter isothermer und nichtisothermer Beanspruchung T2 - Werkstoffprüfung 2011 CY - Berlin, Germany DA - 2011-12-01 PY - 2011 AN - OPUS4-24904 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bloching, H. A1 - Kühn, Hans-Joachim A1 - Aegerter, J. T1 - DIN EN ISO 6892-2: Wesentliche Änderungen in der Norm zum Warmzugversuch T2 - Werkstoffprüfung 2011 CY - Berlin, Germany DA - 2011-12-01 PY - 2011 AN - OPUS4-24905 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schalau, Bernd T1 - Freistrahlmodelle im Vergleich T2 - DECHEMA Fortbildung: Stoff- und Energiefreisetzungen in der Sicherheitstechnik CY - Frankfurt am Main, Germany DA - 2011-11-29 PY - 2011 AN - OPUS4-24906 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schalau, Bernd T1 - VDI Richtlinie 3783 Blatt 1; Ausbreitung von störfallbedingten Freisetzungen - Sicherheitsanalyse T2 - DECHEMA Forrbildung: Stoff- und Energiefreisetzungen in der Sicherheitstechnik CY - Frankfurt am Main, Germany DA - 2011-11-29 PY - 2011 AN - OPUS4-24907 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häßler, Dustin T1 - Berechnung der Tragfähigkeit von historischen Eisenträgern mit Hilfe der Finite-Elemente-Methode T2 - 13. Lausitzer FEM-Symposium CY - Cottbus, Germany DA - 2011-11-25 PY - 2011 AN - OPUS4-24908 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mitropetros, Konstaninos A1 - Pfeil, Norbert T1 - Aktivitäten der Fachgemeinschaft Sicherheitstechnik für Kompetenzerhalt und Ausbildung T2 - Beiratssitzung der ProcessNet-Fachgruppe "Aus- und Fortbildung in der Verfahrenstechnik" CY - Frankfurt am Main, Germany DA - 2011-12-02 PY - 2011 AN - OPUS4-24909 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Rudolf T1 - Entwicklung und Validierung von Immunoassays unterschiedlicher Formate T2 - zmdb-Workshop "Trends in Bioanalysis" CY - Wildau, Germany DA - 2011-05-26 PY - 2011 AN - OPUS4-24940 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Rudolf A1 - Bahlmann, Arnold A1 - Carvalho, José Joao A1 - Lehmann, Andreas T1 - LC-ELISA coupling for structure elucidation of transformation products of pharmaceuticals in surface water T2 - EmCon 2011 CY - Copenhagen, Denmark DA - 2011-08-25 PY - 2011 AN - OPUS4-24943 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Simone A1 - Werrel, Martin A1 - Deubel, Jan T1 - A Controlled-atmosphere Cone Calorimeter-Experiences and Characteristics T2 - Flammschutz-Workshop CY - Ludwigshafen am Rhein, Germany DA - 2011-11-28 PY - 2011 AN - OPUS4-24946 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Rudolf T1 - Immunoanalytical Methods for the Environmental Sciences T2 - Vortrag im Rahmen des Schwerpunktes "CITE - Chemicals In The Environment" CY - Leipzig, Germany DA - 2011-12-02 PY - 2011 AN - OPUS4-24947 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trommsdorf, Stephan T1 - Marktaufsichtsprogramme der Mitgliedstaaten T2 - 1. ERFA Marktüberwachung BMWi CY - Berlin, Germany DA - 2011-09-12 PY - 2011 AN - OPUS4-25340 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trommsdorf, Stephan A1 - Mätzner, Olaf T1 - Die deutsche Produktinfostelle T2 - Verbandsitzung des Verbandes für anorganische Dämmstoffe DiBT CY - Berlin, Germany DA - 2011-09-21 PY - 2011 AN - OPUS4-25341 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Rahman, Mehbub-Ur T1 - Optimization of in-line defect detection by eddy current techniques PY - 2011 UR - http://www.uni-kassel.de/upress/online/frei/978-3-86219-168-0.volltext.frei.pdf SN - 978-3-86219-168-0 SP - 1 EP - 119 PB - Kassel University Press GmbH CY - Kassel AN - OPUS4-25344 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reimund, Verena A1 - Pelkner, Matthias A1 - Neubauer, Andreas A1 - Thomas, Hans-Martin A1 - Kreutzbruck, Marc T1 - Automatische Detektion von Rissen in Stahlbauteilen unter Verwendung von GMR-Sensoren bei der magnetischen Streuflussprüfung N2 - GMR-Sensor Arrays ermöglichen eine örtlich hoch aufgelöste Messung magnetischer Streufeldamplituden an Stahlbauteilen, bei der abhängig von der Größe der zu prüfenden Oberfläche erhebliche Datenmengen erzeugt werden. Eine automatische Detektion von Rissen kann anschließend mittels digitaler Bildverarbeitung erreicht werden, welche hauptsächlich auf einer Kantenerkennung basiert. Diese wurde anhand einer Magnetometer-Messung getestet, die an einem zylindersymmetrischem Bauteil mit funkenerosiv eingebrachten Rissen geringer Tiefe durchgeführt wurde. Die erzielte Selektion der Defekte wird für eine angestrebte Rekonstruktion der Defektgeometrie benötigt. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Deutschland DA - 30.05.2011 KW - GMR-Sensor KW - Streuflussprüfung PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-253451 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Mo.3.C.4) SP - 1 EP - 7 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25345 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rack, T. A1 - Zabler, S. A1 - Rack, C. A1 - Stiller, M. A1 - Riesemeier, Heinrich A1 - Cecilia, A. A1 - Nelson, K. T1 - Coherent synchrotron-based micro-imaging employed for studies of micro-gap formation in dental implants N2 - Biocompatible materials such as titanium are regularly applied in oral surgery. Titanium-based implants for the replacement of missing teeth demand a high mechanical precision in order to minimize micro-bacterial leakage, especially when two-piece concepts are used. Synchrotron-based hard x-ray radiography, unlike conventional laboratory radiography, allows high spatial resolution in combination with high contrast even when micro-sized features in such highly attenuating objects are visualized. Therefore, micro-gap formation at interfaces in two-piece dental implants with the sample under different mechanical loads can be studied. We show the existence of micro-gaps in implants with conical connections and study the mechanical behavior of the mating zone of conical implants during loading. The micro-gap is a potential source of implant failure, i.e., bacterial leakage, which can be a stimulus for an inflammatory process. T2 - 10th International conference on X-ray microscopy CY - Chicago, Illinois, USA DA - 15.08.2010 KW - X-ray imaging KW - Dental implants KW - Digital radiography KW - Implant-abutment interface KW - Synchrotron radiation KW - X-ray phase contrast PY - 2011 SN - 978-0-7354-0925-5 DO - https://doi.org/10.1063/1.3625398 N1 - Serientitel: AIP conference proceedings – Series title: AIP conference proceedings VL - 1365 SP - 445 EP - 448 AN - OPUS4-25347 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tötzke, C. A1 - Manke, I. A1 - Hartnig, C. A1 - Kuhn, R. A1 - Riesemeier, Heinrich A1 - Banhart, J. T1 - Investigation of carbon fiber gas diffusion layers by means of synchrotron X-ray tomography N2 - The 3-dimensional spatial distribution of liquid water in different gas diffusion layer (GDL) materials was analyzed using synchrotron X-ray tomography. The capability of the method was demonstrated by virtually separating the GDL components in order to facilitate individual analysis of fiber material, liquid water and gas filled pore spaces. The influence of hydrophobic surface treatment on the water distribution in the GDL was illustrated by analyzing three GDL materials with different degrees of hydrophobicity. In the least hydrophobic sample, liquid water tends to form larger clusters which stretch out about several hundred µm inside the porous GDL. In contrast, only small water clusters were found in the strongly hydrophobic material with high Polytetrafluoroethylene (PTFE)-content as the liquid is partially pressed out of the GDL. Additionally, the influence of fiber orientation on the water distribution in the felt material was demonstrated. KW - Synchrotron X-ray tomography KW - Fuel cell KW - Gas diffusion layer (GDL) materials KW - Analysis of fiber material PY - 2011 DO - https://doi.org/10.1149/1.3635571 SN - 1938-6737 SN - 1938-5862 VL - 41 IS - 1 SP - 379 EP - 386 CY - Pennington, NJ, USA AN - OPUS4-25348 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nehrig, Marko A1 - Wille, Frank A1 - Quercetti, Thomas A1 - Masslowski, Jörg-Peter A1 - Droste, Bernhard A1 - Pope, R. T1 - Historical view and experiences with crush test for light weight packages N2 - The crush test for light weight and low density type B packages was introduced for the first time into the 1985 edition of the International Atomic Energy Agency (IAEA) transport safety regulations. In the early 1970s, the need for an additional mechanical test besides or instead of the well known 9 m drop test was deliberated. Various authors and test facilities, including BAM and Sandia National Laboratories (SNL), were able to prove that the level of safety provided by IAEA drop and puncture tests in the regulations did not protect against dynamic crush forces to smaller packages. As early as the third PATRAM symposium held in 1971 (Richland, WA, USA), Robert F. Barker asked for '... a more strenuous crushing test for protecting small, light weight packages ...' BAM developed from research activities a proposal as to which types of packages should be subject to crush tests and how the crush tests should be performed, which was presented at the 5th PATRAM symposium held in 1978 (Las Vegas, NV, USA). At the IAEA, the possible need for a crush test was first mentioned in 1977. The subject for a discussion, besides the principal need for this test, was also the development of suitable set of crush test boundary conditions. It took more than four years of discussion until a dynamic crush test similar to today's test was recommended by experts to the IAEA regulatory revision panel. Finally, after a rigorous evaluation process in which also the boundary conditions were determined, the crush test was proposed to be incorporated into the IAEA regulations. BAM and SNL participated in the crush test development and implementation process right from the beginning in the early 1970s until its implementation in the IAEA regulations in 1985. Today, BAM performs crush test procedures according to para. 727(c) of TS-R-1, which have not been changed since their first implementation. Crush tests performed in 2002 at BAM will be discussed. These approval design tests were performed on birdcage pellet transport containers under normal and accident conditions according to the IAEA regulations. KW - Package testing KW - Crush testing KW - Regulations PY - 2011 DO - https://doi.org/10.1179/1746510911Y.0000000016 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 22 IS - 3 SP - 125 EP - 129 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-25349 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter T1 - CFD simulation to predict the performance of a peroxy-fuel burner N2 - new burner concept for peroxy-fuels is proposed. The performance of the proposed peroxy-fuel burner is predicted with the help of Computational Fluid Dynamics (CFD) simulation. It is found that peroxy-fuel burner not only requires considerable less amount of fuel for the same output/power but also at the same time the overall size of the processing unit can be reduced. As peroxy-fuels contain oxygen atoms within the molecule itself a similar to oxy-fuel combustion environment is created without even supplying pure oxygen. CFD simulations also support the above facts and demonstrate the existence of less favorable conditions to form NOx. T2 - 38th National conference on fluid mechanics and fluid power CY - Bhopal, India DA - 15.12.2011 KW - Burner KW - Peroxy-fuels KW - Performance KW - CFD simulation PY - 2011 IS - Paper HT-07 SP - 1 EP - 6 AN - OPUS4-25380 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Bernd R. A1 - Tötzke, C. A1 - Manke, I. A1 - Arlt, Tobias A1 - Markötter, H. A1 - Hilger, A. A1 - Kardjilov, N. A1 - Krüger, P. A1 - Scholta, J. T1 - Non-Destructive Analysis of Water and Media Distribution in Fuel Cells by Means of Neutron and Synchrotron X-ray Imaging T2 - 220th ECS Meeting and Electrochemical Energy Summit CY - Boston, MA, USA DA - 2011-10-09 PY - 2011 AN - OPUS4-25381 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kotschate, Daniel A1 - Gohlisch, Stephan A1 - Heckel, Thomas A1 - Sondermann, F. T1 - Bildgebende Ultraschallhandprüfeinrichtung für die Ausbildung N2 - Um den vermehrten Einsatz von mechanisierten Prüfeinrichtungen bei der Ultraschallprüfung in der Ausbildung Rechnung zu tragen, ist es wünschenswert, dieses Themenfeld bereits zu einem frühen Zeitpunkt in die Ultraschallkurse zu integrieren. Aus diesem Grund wurde für die Ausbildung bei der DGZfP in Zusammenarbeit mit der BAM ein teilmechanisiertes Ultraschall-Prüfsystem entwickelt. Das System basiert auf einem handelsüblichen Ultraschallgerät für die Handprüfung und einem Netbook-Computer. Die berührungslose Positionserfassung wird über den Blenden-Ausgang des Ultraschallgerätes getriggert und die Daten werden mittels Infrarot- und Bluetoothtechnik übertragen. Dies ermöglicht einen kompakten und portablen Aufbau mit kurzen Einrichtzeiten, der sich im Rahmen einer Lehrveranstaltung effektiv einsetzen lässt. Die Ergebnisdarstellung erfolgt mit C-Bildern. An einfachen Übungsstücken können die Kursteilnehmer, dicht an die Handprüfung angelehnt, die Methoden und Randbedingungen einer mechanisierten Prüfung erfahren. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Ultraschallprüfsystem KW - Ultraschallprüfung PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-253826 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Poster 89) SP - 1 EP - 4 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25382 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas A1 - Boehm, Rainer A1 - Gohlke, Dirk T1 - Optimierung von Ultraschall-fokusprüfköpfen beim Einsatz an stark gekrümmten Oberflächen N2 - Bei der Prüfung von gekrümmten Bauteilen in Tauchtechnik muss man die Veränderung des Schallfeldes durch die Form der Oberfläche berücksichtigen. Insbesondere bei hochauflösenden Ultraschallprüfungen mit Fokusprüfköpfen kommt es hierbei zu drastischen Verzerrungen des Schallfeldes. Diese Verzerrungen sind bei der Empfindlichkeitseinstellung sowie bei der Auslegung von Fokuspunkt- und Spurabstand zu berücksichtigen, um eine ausreichende Prüfempfindlichkeit zu erreichen. Es werden Beispiele von Simulationsrechnungen an typischen Prüfanordnungen vorgestellt. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Fokusprüfköpfe KW - Gekrümmte Oberflächen PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-253841 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Poster 62) SP - 1 EP - 5 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25384 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gohlke, Dirk A1 - Kotschate, Daniel A1 - Heckel, Thomas T1 - Visualisierung der Volumenmessdaten von hochauflösenden Ultraschalltauchtechnikprüfungen N2 - Die heutigen Anforderungen an Bauteile und deren Materialien werden immer höher. Somit steigen auch die Anforderungen an die notwendigen Prüfverfahren zur Qualitätsbestimmung bzw. –erhaltung. Durch den optimierten Einsatz von mechanisierten Prüfverfahren und der Verwendung von Visualisierungsalgorithmen wird es möglich, Prüfergebnisse mehrdimensional und farbcodiert z.B. als Überblicksansicht über das Volumen des geprüften Bauteils zu bekommen. Bei der hochauflösenden Volumenprüfung eines Bauteils mittels Ultraschall-Tauchtechnikverfahren, bei dem anstelle einer einfachen Ja/Nein – Aussage eine detaillierte Analyse erforderlich ist, ist es notwendig, alle Messdaten, d.h. jedes A-Bild an jedem Ort, zu speichern. Bei der Auswertung der Daten werden vorwiegend 2D-Darstellungen, wie z.B. das C-Bild der gescannten Fläche, B-Bilder der Scan- und Index-Ebene sowie das A-Bild an der jeweiligen Position verwendet. Um sich z.B. ein Überblick über das Volumen zu verschaffen, werden die B-Bilder der jeweiligen Ebene gescrollt. Bei diesem Verfahren erhält man zwar eine genaue Aussage in den einzelnen Ebenen, aber doch wenig Informationen über die Lage der Anzeigen im Prüfvolumen. Eine 3D-Visualisierung der Volumenmessdaten liefert unter Berücksichtigung der Bauteilgeometrie und einer Farbcodierung der Amplitudenwerte eine übersichtliche Darstellung über Lage, Größe und Verteilung der Anzeigen im Volumen des Bauteils. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Volumenprüfung KW - Tauchtechnik PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-253859 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Poster 61) SP - 1 EP - 6 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25385 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas A1 - Boehm, Rainer A1 - Gohlke, Dirk A1 - Völz, Uwe T1 - Analyseprüfung von Eisenbahnradsatzwellen mit Ultraschall N2 - Die wiederkehrende zerstörungsfreie Prüfung von längs gebohrten Eisenbahnradsatzwellen mit Ultraschall erfolgt im eingebauten Zustand aus der Wellenbohrung heraus. Neben den aufzufindenden Fehleranzeigen erzeugt aufgrund der geometrischen Bedingungen der Radsatzwelle hierbei jeder Querschnittsübergang eine umlaufende Formanzeige in der Ergebnisdarstellung. Durch den Prozess des Aufschrumpfens der Radscheiben auf die Sitze können weiterhin örtlich statistisch verteilte Bereiche im Sitz entstehen, die bei der Ultraschallprüfung Anzeigen hervorrufen, die so genannten Scheinanzeigen. Insbesondere in den Bereichen der Querschnittsübergänge ist zum einen die Prüfsituation sehr komplex, zum anderen ist hier die Wahrscheinlichkeit für eine Rissbildung am höchsten. Bei der Befundanalyse stößt die derzeit verwendete Prüftechnik in diesen Bereichen an ihre Grenzen, so dass nicht immer eine eindeutige Prüfaussage erfolgen kann. Im Bericht werden Lösungsansätze für Analyseverfahren vorgestellt, die auf Basis der Gruppenstrahlertechnik bzw. mit Fokusprüfköpfen in Verbindung mit dem Einsatz von Signalverarbeitung vielversprechende Ergebnisse zur Optimierung dieser Situation aufzeigen. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Eisenbahnradsatzwellen KW - Radsatzwellen PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-253863 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Di.2.A.3) SP - 1 EP - 9 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25386 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lang, Thomas A1 - Koshkina, Olga A1 - Maskos, Michael A1 - Bantz, C. T1 - Multifunctional, polymeric nanoparticles in biological environments T2 - 25th European Colloid and Interface Society meeting (ECIS) CY - Berlin, Germany DA - 2011-09-04 PY - 2011 AN - OPUS4-25387 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kienle, L. A1 - Duppel, V. A1 - Mogwitz, B. A1 - Janek, J. A1 - Kreutzbruck, Marc A1 - Leineweber, A. A1 - Simon, A. T1 - Synthesis - real structure - property: the showcase of silver-rich Ag2Se N2 - The structures and properties of silver selenide samples strongly depend on the method of preparation. Thin films prepared by pulsed laser deposition (PLD) contain lamellae of two low-temperature modifications of Ag2Se whose structures were analyzed in detail by electron microscopy techniques. Besides the stable and known Naumannite-type phase (LT1), a metastable phase was observed (LT2), and the phase transformation was examined in situ. Via cooling and annealing, LT2 becomes dominant in thin films, thus enabling solving the structure of LT2 by electron diffraction. These experiments and HRTEM point to an Acanthite-type (stable low-temperature modification of Ag2S) structure of LT2. Rapid-quenching procedures were applied for the first synthesis of LT2 as bulk sample. Depending on the conditions of melt spinning experiments, well-defined products were formed. In one series, we found a separation of LT1 and LT2 into distinct morphologies, i.e. microspheres and dendrites, respectively. The results on the magnetoresistance of the rapidly quenched materials support previous work. PY - 2011 DO - https://doi.org/10.1021/cg200167j SN - 1528-7483 VL - 11 IS - 6 SP - 2412 EP - 2421 PB - American Chemical Society CY - Washington, DC, USA AN - OPUS4-25388 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wloka, Monika A1 - Bosch, W. T1 - DIN EN ISO/IEC 17025 Allgemeine Anforderungen an die Kompetenz von Prüf- und Kalibrierlaboratorien T2 - DIN Seminar Kompetenz von Laboratorien DIN EN ISO/IEC 17025 CY - Berlin, Germany DA - 2011-09-27 PY - 2011 AN - OPUS4-25373 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Pelkner, Matthias A1 - Neubauer, Andreas A1 - Blome, Mark A1 - Reimund, Verena A1 - Thomas, Hans-Martin A1 - Kreutzbruck, Marc ED - Chady, T. ED - Gratkowski, S. ED - Takagi, T. ED - Udpa, S.S. T1 - Flux leakage measurements for defect characterization using NDT adapted GMR sensors N2 - High-precision magnetic field sensors are of increasing interest in non destructive testing (NDT). In particular GMR-sensors (giant magneto resistance) are qualified because of their high sensitivity, high signal-to-noise ratio and high spatial resolution. We performed magnetic flux leakage measurements of artificial cracks with a GMR-gradiometer and a 3-axes GMR-magnetometer. Cracks of a depth of 44 μm still could be detected with a sufficient high signal-to-noise ratio. A semi-analytic magnetic dipole model was used for swiftly predicting magnetic stray fields. The reliable reconstruction based on measurements of artificial rectangular-shaped defects is demonstrated. KW - GMR KW - NDT KW - Magnetic flux leakage KW - Reconstruction PY - 2011 SN - 978-1-60750-749-9 SN - 1383-7281 N1 - Serientitel: Studies in applied electromagnetics and mechanics – Series title: Studies in applied electromagnetics and mechanics VL - 35 SP - 217 EP - 224 PB - IOS Press CY - Amsterdam, The Netherlands AN - OPUS4-25374 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taffe, Alexander A1 - Spies, M. A1 - Recknagel, J. A1 - Rieß, H. T1 - Schulung zur zuverlässigen Ortung von Bewehrung in Stahlbetonbauteilen von Kraftwerken N2 - In kerntechnischen Anlagen werden Revisionszeiträume genutzt, um unter anderem Anlagenteile nach dem Stand der Technik zu ertüchtigen und um Nachrüstungsmaßnahmen zur Erhöhung der Betriebssicherheit durchzuführen. Solche Anlagenteile werden häufig mittels Dübelplatten befestigt. Die Dübel sind in Stahl-betonbauteile einzubringen, die kraftwerkstypisch mit dichter Bewehrung versehen sind. Zerstörungsfreie Untersuchungen zur genauen Ortung bewehrungsfreier Orte sind hierzu erforderlich. Bei dieser vermeintlich einfachen Prüfaufgabe wurde deutlich, dass in der Praxis Bedarf an verbesserter Anwendungssicherheit der zur Verfügung stehenden ZFP-Verfahren besteht, die eng mit der Ausbildung von Prüfern verbunden ist. Dieser Beitrag berichtet über die bislang im Bereich ZfPBau erstmalig umgesetzte Strategie aus Verfahrensanweisung und Schulung zur zuverlässigen Ortung von Bewehrung an Stahlbetonbauteilen. Sie kann als Muster für weitere ZfPBau-Schulungen zur zuverlässigen Anwendung der Verfahren dienen. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Zerstörungsfreie Prüfung im Bauwesen KW - Ausbildung KW - Bewehrungsortung KW - Performance demonstration KW - Blindtest KW - Wirbelstrom KW - Radar PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-253752 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Di.2.B.1) SP - 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25375 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taffe, Alexander A1 - Kind, Thomas A1 - Stoppel, Markus A1 - Kurz, J. H. T1 - OSSCAR-Bauwerkscanner: Automatisierte Datenaufnahme von Radar, Ultraschall und Wirbelstrom an Spannbetonbauteilen mit bildgebender Darstellung der inneren Konstruktion N2 - Bereits seit vielen Jahren stehen Anwendern der zerstörungsfreien Prüfung im Bauwesen (ZfPBau) zuverlässige Geräte für Radar-, Wirbelstrom- und Ultraschallmessungen an Betonbauteilen zur Verfügung. Doch erst die Kombination dieser drei Verfahren an einer Messfläche erlaubt den maximalen Informationsgewinn über die innere Konstruktion von Stahlbeton- und Spannbetonbauteilen. Mit dem OSSCAR-Bauwerkscanner wurden diese drei Verfahren erstmals zur kombinierten und automatisierten Datenaufnahme an einem Scannerrahmen und unter einer Software vereint. Die Ergebnisse werden bildgebend in frei wählbaren Schnitten dargestellt, was eine Rekonstruktion von Bauteilen erlaubt, für die keine Planunterlagen vorliegen. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Zerstörungsfreie Prüfung im Bauwesen KW - Bauwerkscanner KW - Brückenprüfung KW - Ultraschall KW - Radar KW - Wirbelstrom KW - Kombination PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-253767 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Mi.3.B.1) SP - 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25376 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sojref, Regine A1 - Güther, Wolfgang T1 - Solvent-based redispersion of fine (<200 nm) corundum powder pre-milled in water T2 - ECerS XII - 12th Conference of the European ceramic society CY - Stockholm, Sweden DA - 2011-06-19 KW - Powder processing KW - Redispersion KW - Tape casting KW - Corundum KW - Hydrophobization PY - 2011 SP - 1 EP - 4 AN - OPUS4-25379 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kreutzbruck, Marc A1 - Pelkner, Matthias A1 - Reimund, Verena A1 - Neubauer, Andreas T1 - GMR Array Based Magnetic Flux Leakage Inspection T2 - NDE 2011 CY - Chennai, India DA - 2011-12-08 PY - 2011 AN - OPUS4-25320 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kreutzbruck, Marc A1 - Boehm, Rainer A1 - Kitze, Jessica A1 - Brackrock, Daniel A1 - Prager, Jens A1 - Brekow, Gerhard T1 - Progress in Defect Sizing NDT Methods for the Inspection of Power Plant Components T2 - 37. MPA-Seminar 2011 CY - Stuttgart, Germany DA - 2011-10-06 PY - 2011 AN - OPUS4-25321 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reimund, Verena A1 - Kreutzbruck, Marc A1 - Pelkner, Matthias A1 - Neubauer, Andreas A1 - Thomas, Hans-Martin T1 - Automatische Detektion von Rissen in Stahlbauteilen unter Verwendung von GMR-Sensoren bei der magnetischen Streuflussprüfung T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-25322 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helm, C. A1 - Eichler, Thorsten A1 - Raupach, M. A1 - Isecke, Bernd T1 - Time dependency of current and potential distribution during the cathodic protection of RC structures N2 - Cathodic protection (CP) is a common method for rehabilitation of reinforced concrete structures suffering from Chloride induced corrosion. A sufficient protection of the corroding rebar can be ensured by use of several protection criteria. The use of these assessment criteria, in particular the so called 100 mV-criterion, can lead to erroneous resuits for certain unconventional arrangements of rebar and cp anode. Therefore a joint research project of the Institute for Building Materials Research, RWTH-Aachen University, Germany, (ibac) and the Federal Institute for Materials Research and Testing, Berlin, Germany, (BAM) has been set up to determine the applicability of CP under arbitrary geometrical conditions. A special focus was set on the applicability of surface applied anode Systems for protection of the reinforcement of structures opposite to the accessible side (e.g. outer side of tunnel Shell, Bridge deck protected from inside a box girder) In this paper, the impact of the time dependent changes of the Polarisation behaviour of the rebar on the current and potential distribution is shown by means of parametric studies using the FEM method. T2 - EUROCORR 2011 - Developing solutions for the global challenge CY - Stockholm, Sweden DA - 04.09.2011 KW - Cathodic protection KW - Long time effects of cathodic polarisation KW - FEM-modelling KW - Steel in concrete PY - 2011 SP - 1 EP - 11 AN - OPUS4-25326 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Harrer, Andrea A1 - Prager, Jens A1 - Kreutzbruck, Marc A1 - Guderian, Matthias A1 - Meyer-Plath, Asmus T1 - Erzeugung von Luftultraschall mit mikro- und nanostrukturierten Kohlenstoffmaterialien unter Ausnutzung des thermoakustischen Prinzips N2 - In diesem Beitrag wird ein neuartiger Ansatz zur Erzeugung von Luftultraschall vorgestellt, der auf dem thermoakustischen Prinzip beruht. Mikro- und nanostrukturierte Kohlenstoffmaterialien werden dabei mit einem harmonischen Wechselstrom gespeist und erfahren durch ohmsche Verluste eine Temperaturänderung, die sich auf das umgebende Fluid überträgt. Daraus resultieren Druckmodulationen, und es wird eine ausbreitungsfähige Schallwelle erzeugt. Dabei tritt Frequenzverdopplung gegenüber der Anregungsfrequenz auf. Es konnte gezeigt werden, dass der entscheidende Parameter für die Effizienz der Methode, d.h. für ein möglichst großes Verhältnis von Schalldruck zu eingebrachter Leistung, die Wärmekapazität pro Flächeneinheit ist. Da dieser Quotient für Kohlenstoffmaterialien sehr klein sein kann, erlaubt das thermoakustische Prinzip hier die effiziente Erzeugung von Luftultraschall. Schalldruckmessungen an verschiedenen Materialproben wurden bis 100 kHz mit einem Mikrofon durchgeführt, oberhalb von 100 kHz wurde eine laservibrometrische Schnellemessung eingesetzt. In experimentellen Untersuchungen wurde die Schallerzeugung in Abhängigkeit der Materialeigenschaften analysiert und systematisiert. Die experimentellen Ergebnisse wurden mit numerischen und analytischen Berechnungsergebnissen verglichen. T2 - DAGA 2011 - 37. Jahrestagung für Akustik - Fortschritte der Akustik CY - Düsseldorf, Germany DA - 21.03.2011 KW - Thermoakustisches Prinzip KW - Luftultraschall KW - Kohelnstoffmaterialien PY - 2011 SN - 978-3-939296-02-7 SP - 339 EP - 340 AN - OPUS4-25328 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kolkoori, Sanjeevareddy A1 - Rahman, Mehbub-Ur A1 - Chinta, P.K. A1 - Prager, Jens T1 - Computationally efficient ray tracing algorithm for simulation of transducer fields in anisotropic materials N2 - This contribution describes a computationally efficient ray tracing algorithm for evaluating transducer generated ultrasonic wave fields in anisotropic materials such as austenitic cladded and austenitic weld components. According to this algorithm, ray paths are traced during its propagation through various layers of the material and at each Interface the problem of reflection and transmission is solved. The presented algorithm evaluates the transducer generated ultrasonic fields accurately by taking in to account the directivity, divergence, density of rays, phase relations as well as transmission coefficients. The ray tracing algorithm is able to calculate the ultrasonic wave fields generated by a point source as well as a finite dimension transducer. The simulation results are compared quantitatively with the results obtained from Elastodynamic Finite Integration Technique (EFIT) on several configurations generally occuring in the ultrasonic non destructive testing of anisotropic materials. The excellent agreement between both models confirms the validity of the presented ray tracing algorithm. Finally, the ray tracing model results are also validated by means of experiments. T2 - NDE 2011 - National seminar & exhibition on non-destructive evaluation CY - Chennai, India DA - 08.12.2011 KW - Ultrasonic sound field KW - Ray tracing KW - Directivity KW - Anisotropy KW - Austenitic weld PY - 2011 SP - 482 EP - 486 AN - OPUS4-25329 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taffe, Alexander A1 - Feistkorn, Sascha T1 - Verwendung des GUM zur Nachweisführung mit Hilfe der Zuverlässigkeitstheorie N2 - Die GUM-Prozedur zur Ermittlung der Messunsicherheit hat sich im Bereich der zerstörungsfreien Prüfung im Bauwesen (ZfPBau) als geeignet erwiesen, ZfPBau-Verfahren bei der Validierung von Prüfaufgaben zu charakterisieren. Darüber hinaus können die Modellgleichungen und die quantifizierten Eingangsgrößen Eingang in Berechnungen auf der Basis der Zuverlässigkeitstheorie finden. Damit ist es möglich, die Auswirkung der berücksichtigten Einflussgrößen auf die Zuverlässigkeit einer Prüfaussage zu quantifizieren. N2 - The process to calculate the uncertainty of measurements according to the GUM has been adopted in the field of non-destructive testing in civil-engineering (NDT-CE) and helps to characterise methods in the validation process for different testing tasks. Furthermore model equations and their quantified influence quantities can be used for calculations based on the reliability theory. This allows quantifying the effect of the influence quantities on the reliability of a test result. T2 - 5. Fachtagung 'Messunsicherheit praxisgerecht bestimmen' CY - Erfurt, Germany DA - 08.11.2011 KW - Zerstörungsfreie Prüfung im Bauwesen KW - Zuverlässigkeitstheorie KW - GUM KW - STRUREL KW - FORM KW - SORM KW - Statistischer Nachweis KW - Messunsicherheit PY - 2011 SN - 978-3-18-092149-5 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte VL - 2149 SP - 181 EP - 190 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-25393 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bléger, D. A1 - Liebig, T. A1 - Thiermann, Raphael A1 - Maskos, Michael A1 - Rabe, J.P. A1 - Hecht, S. T1 - Light-orchestrated macromolecular 'accordions': reversible photoinduced shrinking of rigid-rod polymers N2 - Lichtspiele: Lichteinstrahlung verursacht drastische Änderungen der Form stabförmiger Polymere mit Azobenzol‐Photochromen in der Hauptkette. Die eingebetteten Photoschalter wirken als molekulare Scharniere, die bei lichtinduzierter Isomerisierung zur reversiblen Schrumpfung und Streckung des Polymerrückgrats führen (siehe Schema); das System erinnert an ein lichtorchestriertes makromolekulares Akkordeon. N2 - Synthetic molecular systems undergoing structure and property changes as a response to external stimuli offer a series of relevant functions. Their direct use in solution, immobilized at surfaces, or integrated into adequate matrices, allow for the elaboration of nano-carriers, molecular electronic memory circuits, adaptive systems, artificial muscles, or healable materials, among others. Reversible systems are commonly generated by utilizing molecular switches as responsive bi-stable molecules. Of particular interest are switches controlled by non-invasive triggers, especially light, which can display high spatial and temporal resolution. Photoswitches were used to change properties, such as conductance and basicity, based on light-induced alteration of the molecular geometry, that is, their dimensions and shape. In nature, light-induced geometrical modifications of molecular systems lead to primary biological functions, such as the visual perception in vertebrates, or proton pumping in some bacteria, two examples that nicely illustrate the potential of photo-inducing structural modifications in organic systems. KW - Aggregation KW - Azoverbindungen KW - Nanostrukturen KW - Photochromie KW - Polymere PY - 2011 DO - https://doi.org/10.1002/ange.201106879 SN - 0044-8249 SN - 0932-2140 SN - 1521-3757 VL - 123 IS - 52 SP - 12767 EP - 12771 PB - Wiley-VCH CY - Weinheim AN - OPUS4-25394 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madia, Mauro A1 - Zerbst, Uwe A1 - Hellmann, D. T1 - Analytical model for fracture mechanics based S-N curve prediction T2 - International Symposium on Fatigue Design and Material Defects CY - Trondheim, Norway DA - 2011-05-23 PY - 2011 AN - OPUS4-25395 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wallstabe, Ronald T1 - Interdisziplinäre Schadensanalyse aus dem Leben gegriffen: Beispiele aus den Bereichen Freizeit, Medizin und Landwirtschaft T2 - BAM-Kolloquium CY - Berlin, Germany DA - 2011-02-09 PY - 2011 AN - OPUS4-25396 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schurig, Michael A1 - Klinger, Christian A1 - Schöne, Dieter A1 - Bork, Claus-Peter A1 - Klingbeil, Dietmar T1 - Very high cycle fatigue testing on an electrodynamic shaker system T2 - VHCF-5, Fifth international conference on Very High Cycle Fatigue CY - Berlin, Germany DA - 2011-06-28 PY - 2011 AN - OPUS4-25397 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klinger, Christian T1 - Die Bedeutung des "Materialfehlers" aus der Sicht von Laien, Juristen und Ingenieuren - Materialfehler in Literatur, Regelwerk und Gutachten T2 - VDI Jahrestagung Schadensanalyse CY - Würzburg, Germany DA - 2011-10-19 PY - 2011 AN - OPUS4-25398 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Memhard, D. A1 - Häcker, Ralf A1 - Andrieux, F. A1 - Sun, D.-Z. T1 - Development and verification of a material model for prediction of containment safty of exhaust turbochargers T2 - 8th European LS-DYNA Users Conference CY - Strasbourg, France DA - 2011-05-23 PY - 2011 AN - OPUS4-25399 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heyn, Andreas T1 - Korrosionsprüfungen unter die Lupe genommen - Einflussfaktoren, Zusammenhänge, Simulationsansätze T2 - DFO Qualitätstage CY - Cologne, Germany DA - 2011-11-29 PY - 2011 AN - OPUS4-24829 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Burkert, Andreas A1 - Beck, M. T1 - Detektion von Bewehrungsstahlkorrosion nach dem DGZfP - Merkblatt B 3 zur elektrochemischen Potentialfeldmessung N2 - Im ersten Teil dieses Beitrags [1] sind die Grundlagen der Passivität und der Depassivierung sowie des Korrosionsfortschritts von Stahl in Beton eingehend dargestellt worden. Die entstehenden Korrosionsprodukte werden zunächst vom Porengefüge des Betons aufgenommen, ohne dass es zu äußerlich sichtbaren Veränderungen an der Betonoberfläche kommt. Infolge der sich einstellenden Sättigung des Porenraumes mit Korrosionsprodukten und des daraus resultierenden Spannungsaufbaus im Beton können Folgeschäden, wie Risse und Abplatzungen am Bauwerk entstehen, die notwendige Sanierungsmaßnahmen bedingen. KW - Stahlbeton KW - Passivität KW - Chlorinduzierte Korrosion KW - Potentialmessung KW - Einflüsse KW - Fehlerquellen PY - 2011 VL - 3 SP - 5 EP - 8 PB - VBD-Geschäftsstelle CY - Hannover AN - OPUS4-24830 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gili, F. A1 - Igartua, A. A1 - Luther, R. A1 - Woydt, Mathias T1 - The impact of biofuels on engine oil performance N2 - The dilution of biogenic fuels into lubricating engine oils often leads to a shortening of the recommended oil drains (between 30% and 60%) and an increase in wear. The large number of overlapping and influencing factors, of which dilution and polymerization of fuel components in the engine oil are emphasised, makes it difficult to find a uniform solution to prevent failures in the various applications. Insofar single solutions for the different types of biofuels are needed. The contribution of base oil chemistry and additives as well as triboactive materials is featured to deal with the adverse effects of biofuels. In the frame of the European Commission (EC)-funded project 'cleanengine', tentative engine oils based on esters with a content of renewables and polyglycols are formulated to increase the lubricant's tolerance in engines fuelled with biofuel-based blends, with the aim of ensuring required lubricating and wear protection performance while keeping oil drain intervals unchanged. The present paper focuses on four-stroke diesel applications, fuelled by biodiesel (fatty acid methyl ester — FAME) as well as by rapeseed oil and Jatropha oil (pure vegetable oils, triglycerides), together with relevant blends of those biofuels and conventional diesel fuel. This paper screens the functional profile (in particular rheological, toxicological, bio-compatibility, tribological and biofuels affinity) of lube families with respect to biofuel contamination. Moreover, this is followed by the contributions of piston ring and liner materials as well as thin film coatings. KW - Lubricants KW - Engine oil KW - Additives KW - Biofuel KW - Ester KW - Polyglycol KW - Thin film coatings KW - Slip-rolling KW - DLC KW - Dilution KW - FAME KW - Jatropha KW - Rapeseed KW - Stem valve KW - Piston ring PY - 2011 DO - https://doi.org/10.1002/ls.158 SN - 0954-0075 SN - 1557-6833 VL - 23 IS - 7 SP - 313 EP - 330 PB - Leaf Coppin Publ. Ltd. CY - Deal AN - OPUS4-24831 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Grothausmann, R. A1 - Zehl, G. A1 - Manke, I. A1 - Fiechter, S. A1 - Bogdanoff, P. A1 - Dorbandt, I. A1 - Kupsch, Andreas A1 - Lange, Axel A1 - Hentschel, Manfred P. A1 - Schumacher, G. A1 - Banhart, J. T1 - Quantitative structural assessment of heterogeneous catalysts by electron tomography N2 - We present transmission electron microscope (TEM) tomography investigations of ruthenium-based fuel cell catalyst materials as employed in direct methanol fuel cells (DMFC). The digital three-dimensional representation of the samples not only enables detailed studies on number, size, and shape but also on the local orientation of the ruthenium particles to their support and their freely accessible surface area. The shape analysis shows the ruthenium particles deviate significantly from spherical symmetry which increases their surface to volume ratio. The morphological studies help to understand the structure formation mechanisms during the fabrication as well as the high effectiveness of these catalysts in the oxygen reduction reaction at the cathode side of fuel cells. KW - Electron tomography KW - Reconstruction algorithm KW - Catalyst KW - Fuel cell PY - 2011 DO - https://doi.org/10.1021/ja2032508 SN - 0002-7863 SN - 1520-5126 VL - 133 IS - 45 SP - 18161 EP - 18171 PB - American Chemical Society CY - Washington, DC AN - OPUS4-24833 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sander, C. A1 - Kühne, Hans-Carsten A1 - Ünal, Murat A1 - Kleine, M. A1 - Köhler, A. A1 - Kriesten, V. T1 - Betondickglasfenster - Schadensmechanismen und Instandsetzungsprinzipien zur Erhaltung N2 - Errichtet aus Glas und Beton prägen heute unzählige Sakralbauten der 1950er- und 60er-Jahre unsere Stadtbilder. Nicht selten sind in diesen Kirchen erhebliche Schäden an den Betonglasfenstern zu verzeichnen. Diese fachgemäß zu erhalten, erfordert spezielles technisches und denkmalpflegerisches Know-how. An der Entwicklung geeigneter Instandsetzungsstrategien arbeitet derzeit ein interdisziplinäres Projektteam. KW - Betonglasrestaurierung KW - Schadensmechanismen KW - Instandsetzungsprinzipien KW - Glass KW - (Reinforced) concrete KW - Church windows KW - Churches KW - Structural analysis KW - Concrete block technique KW - Reinforcement KW - Dalle de verre PY - 2011 SN - 0933-4017 VL - 7 SP - 48 EP - 53 PB - Callwey CY - München AN - OPUS4-24834 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pistol, Klaus A1 - Weise, Frank A1 - Meng, Birgit A1 - Schneider, U. ED - Koenders, E.A.B. ED - Dehn, F. T1 - The mode of action of polypropylene fibres in high performance concrete at high temperatures N2 - It has been shown in fire tests that polypropylene fibres reduce or avoid explosive spalling of high performance concrete. In the critical temperature ränge up to 300 °C the permeability of HPC increases by using polypropylene fibre. Due to this the water vapour, which is the main reason for explosive spalling, can escape. There exist different theories in the literature conceming the micro structural mechanisms, which cause an increase in the permeability. Within the framework of an internal research project at BAM an innovative methodology was developed for experimental verifying of existing theories and to get new insights into this problem The methodology used is unique and has been undertaken here for the first time. This consists of the combination of acoustic emission and ultrasonic measurement during temperature loading and the non-destructive micro structural analysis of cooled down samples with the aid of micro X-ray computed tomography. For the validation of the nondestructive test methods scanning electron microscopic images of prepared samples were undertaken. The results show that due to the thermal decomposition of the polypropylene fibres micro canals emerge. These are connected due to a simultaneous micro cack formation. T2 - 2nd International RILEM workshop on concrete spalling due to fire exposure CY - Delft, The Netherlands DA - 05.10.2011 KW - Spalling KW - Polypropylene fibres KW - High performance concrete KW - Acoustic emission KW - X-ray computed tomography KW - Scanning electron microscopy PY - 2011 SN - 978-2-35158-118-6 SP - 289 EP - 296 PB - RILEM Publications AN - OPUS4-24835 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miccoli, Lorenzo A1 - Perrone, C. A1 - Müller, Urs A1 - Gardei, André A1 - Ziegert, C. T1 - Comparison of mechanical behavior of different earth masonry typologies in cultural heritage N2 - The paper has been developed in the framework of a larger EC‐research program called NIKER, in which BAM and other seventeen research partners from the Mediterrean area are jointly involved. It aims to develop and validate innovative materials and technologies for the systemic improvement of the seismic behavior of Cultural Heritage assets. The death tolls brought about by recent catastrophes in developing countries where many inhabitants lived in earthen dwellings (Gujarat, India 2001, Bam, Iran 2003 and Concepción, Chile 2010 Earthquakes, Tamil Nadu 2004 Tsunami) have brought about research studies aimed at improving earth construction in terms of strength, seismic resistance and speed of construction. In comparison to the recent advances in research on stone and brick masonry, knowledge on the material properties and failure mechanisms of earthen Building construction is limited and scattered. The research presented here by aims making a comparison of mechanical behaviour between different earth masonry material typologies, consisting of earth block masonry, rammed earth and cob. T2 - WCCE-ECCE-TCCE Joint conference 2 - Seismic protection of cultural heritage CY - Antalya, Turkey DA - 31.10.2011 KW - Earth masonry KW - Material test KW - Cultural heritage KW - Seismic resistance PY - 2011 SN - 978-605-01-0188-1 SP - 25 EP - 36 AN - OPUS4-24836 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit ED - Drochytka, R. ED - Bohus, S. T1 - Natural stone reprofiling in cultural heritage with modular repair mortars N2 - Whenever the preservation of original substance obtains priority in a restoration task, reprofiling techniques using repair mortars are a welcome solution. For ordinary concrete repair aesthetic aspects are of minor importance whereas for the restoration of natural stone elements they come to the fore. Especially for listed buildings and monuments, historico-cultural and aesthetical interests become the ruling Parameters for planning and execution of restoration tasks. Nevertheless the technical and constructive requirements have to be considered and deterioration processes have to be understood to ensure sustainability and durability of the repair task. Due o differences in the Chemical and mineralogical composition, natural stone provides a vast variety of texture and colour. Also the range of different mechanical and durability related properties is far wider than found with concrete for example. A research project dealing with the development of a modular repair mortar System for natural stone is currently set up at the BAM. To provide the conservator with the best possible options to match colour, texture and technical requirements, the System will be setup on a modular basis. Several different binder Systems on basis of cement, lime and sodium Silicate as well as polymer based Systems are planned, which can be combined with different aggregate compositions and different pigments. To evaluate the mortar performance, test procedures will be defined for tests on mortar samples and on composite specimens. In the paper the experimental Programme will be explained and first results will be presented and discussed. T2 - 2nd WTA - Internaitonal PhD Symposium - Building materials and buidling technology to preserve the built heritage CY - Brno, Czech Republic DA - 06.10.2011 PY - 2011 SN - 978-3-937066-21-9 SN - 0947-6830 N1 - Serientitel: WTA-Schriftenreihe – Series title: WTA-Schriftenreihe IS - 36 SP - 208 EP - 216 PB - WTA Publications AN - OPUS4-24837 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fontana, Patrick A1 - Lehmann, Christian A1 - Müller, Urs A1 - Kühne, Hans-Carsten A1 - Meng, Birgit A1 - Rogge, Andreas T1 - Wärmebehandlung und Autoklavierung von UHPC - Neue Perspektiven für die Betonfertigteilindustrie T1 - Heat curing and autoclaving of UHPC - New perspectives for the precast concrete industry N2 - Das Gefüge von UHPC ist durch eine dicht gepackte und fehlstellenarme Matrix gekennzeichnet. Eine zusätzliche Optimierung ist durch eine Wärmebehandlung bzw. hydrothermale Nachbehandlung (Autoklavierung) unter einem Wasserdampfsättigungsdruck möglich. Die Wärmebehandlung von Beton ist ein in der Betonfertigteilindustrie geläufiges Verfahren, um die Erstarrungszeit zu verkürzen und höhere Frühfestigkeiten zu erreichen. N2 - The structure of UHPC is characterized by a densely packed matrix with only a small number of voids; it can be enhanced further by heat curing or hydrothermal Treatment (autoclaving) subject to water vapor pressure. Heat curing of concrete is commonly applied in the precast industry in Order to shorten its setting time and achieve higher early strengths. KW - Ultrahochleistungsbeton KW - Stahlfasern KW - Nachbehandlung KW - Mikrostruktur KW - Festigkeit PY - 2011 SN - 0373-4331 SN - 1865-6528 N1 - Sprachen: Deutsch/Englisch - Languages: German/English VL - 77 IS - 10 SP - 46 EP - 47 PB - Bauverl. CY - Gütersloh AN - OPUS4-24838 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Recknagel, Christoph T1 - Erfahrungen mit flexiblen Fahrbahnübergängen und Stand der Technik in Deutschland N2 - Mehr als 25 Jahre nach dem ersten Einbau eines sogenannten Fahrbahnüberganges aus Asphalt und nach nunmehr 13-jähriger Erfahrungen mit den gütesichernden Maßnahmen des technischen Regelwerks in Deutschland kann eine insgesamt positive Bilanz gezogen werden. Diese Ausführungsvariante der Bauart flexibler Fahrbahnübergang hat mittlerweile einen akzeptierten Platz auf dem Gebiet der Brückenausstattung für Bauwerke mit einer freien Dehnlänge bis zu 30 m eingenommen. Die generelle Bewährung ist aktuelle Motivation, durch stoffliche und konstruktive Weiterentwicklungen die bauartbedingten Vorteile in einen größeren Anwendungsbereich zu überführen. Die baurechtliche Grundlage dafür bilden die neuen europäisch harmonisierten Zulassungsregelungen. Erste Erfahrungen aus der versuchstechnischen Bewertung neuartiger Ausführungsvarianten werden vorgestellt. T2 - ASTRA-EMPA-Tagung - Flexible Fahrbahnübergänge - Erfahrungen und Stand der Technik CY - Dübendorf, Switzerland DA - 18.10.2011 PY - 2011 SP - 1 EP - 7 AN - OPUS4-24809 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chabrelie, A. A1 - Müller, Urs A1 - Scrivener, K.L. ED - Palomo, Á. ED - Zaragoza, A. ED - Agüí, J. C. L. T1 - Mechanisms of degradation of concrete by external sufate ions under laboratory and field conditions N2 - The durability of concrete is a major challenge for the construction, which devotes one third to one half of its annual investment to building maintenance. The lack of fieid data regarding concrete durability, especially in the case of exposure to Sulfate ions (“sulfate attack”) makes it dijficult to determine the appropriate fest methods andperformance criteria. Additionally, the increased use of sustainable blends (cement with mineral admixtures, typically slag from the iron industiy) suffers from a lack of experience regarding their long-term performance. Most results for sulfate resistance are derived from accelerated laboratoiy tests xvhere performance criteria are based only on macroscopic properties, especially expansion. To fill this gap and better widerstand the mechanisms of sulfate attack under real conditions, a parallel study of laboratoiy micro-concrete and fieid concrete samples under sulfate exposure was undertaken, focussing on microstructural changes in addition to the conventional macroscopic characterisation. Four exposure regimes were designed in the laboratoiy: full immersion (ponding), pH-control, semi-immersion and wet/diy cycles. Pure Portland blends and slag blends witli high level of slag replacement (70 wt.-%) were investigated. The exposure regime has been found to play a major role in the damage process. In ponding conditions, the damage process takes place in three stages characterised by a first period of induction, followed by surface damage thatfinally extends to the bulle of the material. Paradoxically, the w/c-ratio does not seem to have much impact on the ionic transport phenomena but might be more decisive in the microstructure mechanical strength against local stresses. The slag blends, considered as sulfate resistant in ponding exposure, revealed badperformances under wet/diy cycles. This beliaviour was attributed to poor proper physical resistance of the slag hydrates against diying. The fieid concretes selected for the comparison with the laboratoiy cases were partially buried in a sulfate-enriched soil in Argentina. A pure Portland blend and a slag blends with high level of slag replacement (80 wt.-%) were investigated. The submerged part of the samples could be compared to the laboratoiy ponding exposure, wliile the upper layer of the samples subjected to weathering could be compared to the laboratoiy wet/diy cycles exposure. The fieid obsen’ations tend to confirm the laboratoiy results and validate the fest settings. It has been underlined that a direct relationship between damage (e.g.; cracking/expansion) andphase assemblage was not evident. However, the study highlights that sulfate combination with the hydrates of the cement (e.g.; C-S-H) and with those of the slag would play a rote in the initiation of the expansion, which would be attributed to a swelling of the hydrates or to the precipitation offine ettringite after the Saturation level in sulfate of the hydrates has been reached. T2 - 13th International congress on the chemistry of cement - XIII ICCC CY - Madrid, Spain DA - 03.07.2011 KW - Sulfate attack KW - Exposure conditions KW - Concrete KW - Laboratory test KW - Field KW - Phase assemblage KW - Microstructure KW - XRD KW - SEM KW - SCM KW - Slag PY - 2011 SN - 978-84-7292-400-0 SP - 1 EP - 14 CY - Madrid AN - OPUS4-24810 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Petrovskii, V.N. A1 - Uspenskii, S.A. A1 - Shcheglov, Pavel A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Investigation of a vapor-plasma welding torch induced by a high-power ytterbium fiber laser KW - Laser welding KW - Condensation KW - Diagnostic of the torch PY - 2011 SN - 2079-5629 VL - 2 IS - 2 SP - 159 EP - 165 PB - MAIK Nauka AN - OPUS4-24811 LA - rus AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Shcheglov, Pavel A1 - Uspenskii, S.A. A1 - Gumenyuk, Andrey A1 - Petrovskii, V.N. A1 - Rethmeier, Michael A1 - Yermachenko, V. M. T1 - Plume attenuation of laser radiation during high power fiber laser welding N2 - The results of an in-situ plume-laser interaction measurement during welding of mild steel with a 5 kW ytterbium fiber laser are reported. A measurement of the attenuation of probe laser beam passing through the plume has allowed to estimate the plume characteristics like the size of the extinction area and the spatial distribution of the extinction coefficient. The power loss of the fiber laser radiation propagating through the whole plume length was calculated. Together with a measured temporal characteristics of extinction the result indicates a significant decreasing of the laser radiation stability, which can lead to the formation of the macroscopic welding defects. KW - Laser welding KW - Plume KW - Beam attenuation KW - Particles PY - 2011 DO - https://doi.org/10.1002/lapl.201110010 SN - 1612-2011 VL - 8 IS - 6 SP - 475 EP - 480 PB - Wiley-VCH CY - Berlin AN - OPUS4-24812 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hartelt, Manfred A1 - Wäsche, Rolf T1 - Verschleißuntersuchungen an Dental-Implantat-Werkstoffen unter partial slip Bedingungen N2 - Im Vortrag wird neben der apparativen Prüftechnik das allgemeine methodische Vorgehen für Modell-Verschleißuntersuchungen im Bereich des partial slip vorgestellt. Im Detail wird für Dental-Implantat-Werkstoffe eine Rangfolge aufgestellt, die vergleichend die Verschleißresistenz unterschiedlicher Ti-basierter Werkstoffe zeigt. Wird durch die Kaubewegung eine mehrachsige Beanspruchung in die Kontaktflächen der Schraubverbindung eingeleitet, kann durch partial slip im Randbereich dieser Kontaktfläche ein Verschleißprozess initiiert werden, der die Lockerung des Implantats begünstigt. Eine gute Verschleißresistenz verhindert oder schiebt die vorzeitige Lockerung hinaus. Um das Werkstoffverhalten in Bezug auf eine vorzeitige Lockerung der Implantatkrone bei geschraubten zweiteiligen Implantaten zu charakterisieren, wurden zylindrische Probekörper unter partial slip Fretting-Bedingungen mit Zyklenzahlen bis n = 200 000 beansprucht. Die Frequenz der aufgebrachten Tangentialkraft betrug 2 Hz, um die Kaubewegung zu simulieren. Die tribologischen Untersuchungen wurden auf einem Eigenbau-Tribometer mit der Kontaktgeometrie „gekreuzte Zylinder“ durchgeführt. Die zylindrischen Proben wurden aus den Werkstoffen Titan Grade 4 und der Ti-Legierung Ti6AI4V gefertigt. Ein Teil dieser Ti-basierten Proben wurde oberflächengehärtet. Die bisher erzielten Ergebnisse zeigen, dass die oberflächenbehandelten Proben dazu neigen, unter der Belastung die Kontaktfläche zu vergrößern. Dies deutet auf einen Effekt bekannt als „junction growth“ und damit auf eine erhöhte Versetzungsbeweglichkeit der randschichtgehärteten Proben hin. Einen Einfluss der Zwischenstoffe konnte nicht nachgewiesen werden. T2 - 52. Tribologie-Fachtagung - Reibung, Schmierung und Verschleiß - Forschung und praktische Anwendungen CY - Göttingen, Germany DA - 26.09.2011 KW - Partial slip KW - Schwingungsverschleiß PY - 2011 SN - 978-3-00-035439-7 VL - I SP - 14/1 EP - 14/11 AN - OPUS4-24813 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Purohit, Purv A1 - Schönhals, Andreas T1 - Structure-Property relationships of nanocomposites based on Polyolefins and Layered Double Hydroxide T2 - Eurofillers 2011 CY - Dresden, Germany DA - 2011-08-21 PY - 2011 AN - OPUS4-24815 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krebber, Katerina A1 - Habel, Wolfgang T1 - Fibre-optic sensors embedded in geotechnical textiles and concrete piles for structural health monitoring N2 - Fibre-optic sensors are more and more used in geotechnical and civil engineering. There are a big number of applications with the purpose of improvement or proof of the structural integrity. This paper, presents two examples where different fibre sensor types.are exploited for safety-relevant task in geotechnique. Technical textiles with embedded distributed fibre-optic sensors based on Brillouin Scattering in silica optical fibres and OTDR (optical time-domain reflectometry) in polymer optical fibres are presented. Such “smart” technical textiles can be used for reinforcement of geotechnical structures and masonry walls, and the embedded fibre-optic sensors can provide information about the condition of the structures as well as detect the presence of any damage and destructions in real time. Highly sensitive fibre-optic geophones based on Fabry-Perot sensors embedded in large concrete pile can be used for precise measurement of Deformation and wave distribution during static and dynamic pile test. Such sensors make the evaluation of the pile’s integrity and load-bearing capacity easier. KW - Faseroptischer Sensor KW - Verteilter Sensor KW - Brillouin-Sensor KW - Polymeroptischer Sensor KW - POF OTDR KW - Technisches Textil KW - Geotextil KW - Dehnungssensor KW - Geophon KW - Pfahltest KW - Akustische Welle KW - Fabry-Perot KW - Fibre-optic sensor KW - Distributed sensor KW - Polymer optical fibres (POF) KW - POF sensor KW - Strain sensor KW - Technical textiles KW - Geotextiles KW - Geophone KW - Fabry-Perot sensor KW - Pile test KW - Impact KW - Acoustic wave PY - 2011 SN - 0002-5968 VL - 7 SP - 252 EP - 263 PB - Wichmann CY - Heidelberg AN - OPUS4-24816 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Huismann, Sven A1 - Weise, Frank A1 - Meng, Birgit A1 - Schneider, U. T1 - Influence of polypropylene fibres on the thermal strain of high strength concrete at high temperatures N2 - This paper presents the results of an experimental study on the influence of polypropylene (PP) fibres on the thermal strain of high strength concrete (HSC) at temperatures up to 750°C. Concerning this topic only few results can be found in the literature and systematic investigations are missing. However, basic knowledge is necessary to understand the internal damage processes as well as for structural design. To explain the differences in the thermal strain of HSC with and without addition of PP fibres the internal damage processes were investigated with acoustic emission (AE) analysis and ultrasound (US). Furthermore the weight loss was measured continuously during heating to monitor the drying of the specimen. This novel approach by combining these different methods with strain measurements at high temperatures allows the integral description of the internal damage processes. The results reveal significant differences in the thermal strain of HSC when PP fibres are added. Between 200°C and 250°C the thermal strain of HSC with PP fibres is superimposed by shrinkage caused by accelerated drying. Above 250°C it is lower than that of plain HSC without PP fibres. It is supposed that it is caused by a more homogeneous distribution of micro cracks whereby the fibre beds acting as defects in the concrete. Hence this paper gives a contribution to the general understanding of the impact of PP fibres in HSC at high temperatures and points out the influence of the fibres on the thermal strain of HSC. KW - High performance concrete KW - High temperatures KW - Polypropylene fibres KW - Thermal strain KW - Acoustic emission KW - Ultrasound PY - 2011 DO - https://doi.org/10.1260/2040-2317.2.3.173 SN - 2040-2317 VL - 2 IS - 3 SP - 173 EP - 179 PB - Multi-Science Publ. Co. CY - Brentwood AN - OPUS4-24817 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pereira, F. A1 - Pistol, Klaus A1 - Korzen, Manfred A1 - Weise, Frank A1 - Pimienta, P. A1 - Carré, H. A1 - Huismann, Sven ED - Koenders, E.A.B. ED - Dehn, F. T1 - Monitoring of fire damage processes in concrete by pore pressure and acoustic emission measurements N2 - This paper presents the combined use of acoustic emission (AE), gas pore pressure and temperature measurements (PT). The simultaneous application of both techniques represents a new methodology in the context of fire spalling and contributes to a better understanding of the mechanisms of fire spalling, particular with regard to the interaction of micro cracking and pore pressure evolution. The study presents fire tests on normal strength concrete specimens with and without reinforcement at ISO Standard fire and at hydrocarbon (HC) fire. Supported by AE-analysis, it can be shown that due to the higher heating rate of the HC-fire in comparison to the ISO Standard fire the damage processes inside the concrete during the exposure are increased combined with augmenting the concrete permeability. As a consequence lower pore pressures were measured. However, despite the lower pore pressures, explosive spalling was observed. T2 - 2nd International RILEM workshop on concrete spalling due to fire exposure CY - Delft, The Netherlands DA - 05.10.2011 KW - Ordinary concrete KW - High temperature KW - Gas pore pressure KW - Acoustic emission KW - Spalling PY - 2011 SN - 978-2-35158-118-6 SP - 69 EP - 77 PB - RILEM Publications AN - OPUS4-24818 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Taffese, W.Z. A1 - Kumaran, G.S. A1 - Uzoegbo, H.C. A1 - Kühne, Hans-Carsten T1 - Inorganic binder systems for innovative panel technology in East Africa - possible ways to produce building materials from local raw materials N2 - Many African countries face serious problems associated with the rapid growth of urban Population and the resulting demand for affordable building materials. In search for appropriate Solutions to improve the Situation, the “LightSHIP” project was initiated, whose aims were to identify the required product specifications, to evaluate possible approaches and ultimately to develop new Building materials for East Africa. It was concluded that these materials should be produced in Africa mainiy from local raw materials; prefabricated, easily transportable construction elements are to be preferred. It is therefore reasonable to focus on artificial stones and partition boards. To be Independent of imported cement, it is suggested to make use of volcanic rocks, which are abundant in East African countries, for lime-pozzoian binders and geopolymers in the production of these construction elements. Future research activities should thus concentrate on assessment of the applicability of available volcanic rocks, the influence of their properties on the resulting binders and the design of appropriate binder-reinforcement-filler Systems. T2 - Workshop cement and concrete for Africa CY - Berlin, Germany DA - 17.08.2011 KW - Building materials KW - East Africa KW - Volcanic rock KW - Natural pozzolans KW - Lime-pozzolan binders KW - Geopolymers PY - 2011 SN - 978-3-9814281-4-8 SP - 32 EP - 36 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-24779 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan A1 - Rübner, Katrin A1 - Meng, Birgit A1 - Hauer, B. T1 - Sustainable evaluation - concept to assess the applicability of secondary aggregates in concrete N2 - Nowadays there are several applications of mineral recycling materials and residues. At present an assessment method for the use of secondary raw materials, which considers sustainability aspects, does not exist. In the framework of the German DAfStb/BMBF research project “Sustainable Building with Concrete” an assessment concept was developed. It includes the following four assessment steps: I. Basic considerations, II. Advantages for sustainable construction, III. Alternative paths for application, and IV. Sensitivity analysis. The concept was developed on the basis of recycled concrete aggregates, which are already used according to German standards. Afterwards, it was applied and verified by the evaluation of the utilisation of municipal solid waste incinerator bottom ashes (referred to MSWI bottom ashes). T2 - 2011 Helsinki world sustainable building conference CY - Helsinki, Finland DA - 18.10.2011 KW - Sustainable building KW - Sustainability aspects KW - Secondary materials KW - Secondary aggregates in concrete KW - Energy and material resources KW - Assessment concept PY - 2011 SN - 978-951-758-534-7 SN - 0356-9403 SP - 1 EP - 8 AN - OPUS4-24781 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Simone A1 - Raspe, Tina T1 - Rauchentwicklung und Rauchgaszusammensetzung von Photovoltaikmodulen im Brandfall T2 - VDI-Expertenforum: Photoviltaik und Brandschutz CY - Düsseldorf, Germany DA - 2011-11-17 PY - 2011 AN - OPUS4-24783 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten T1 - Übersicht zur Normungsarbeit an der DIN 19573 - Mörtel für Neubau und Sanierung von Entwässerungssystemen außerhalb von Gebäuden N2 - Mörtel für den Neubau und die Instandsetzung sind seit vielen Jahrzehnten im Abwasserbereich für unterschiedliche Bereiche im Einsatz. Zumeist werden diese je nach Anwendungsbereich entsprechend der Vorgaben der Auftraggeber, den Erfahrungen der Hersteller und Verwender sowie den Empfehlungen von Interessenverbänden (z. B. DWA oder DVGW verarbeitet. Zugleich ist eine Reihe von adaptierbaren Regelwerken für ähnliche Produkte aus anderen Anwendungsgebieten verfügbar. Während die Regelwerke zum Schutz und zur Instandsetzung von Betonbauteilen bereits seit ca. 35 Jahren über den Deutschen Ausschuss für Stahlbeton und die Bundesanstalt für Straßenwesen entwickelt und fortgeschrieben werden und seit ca. 20 Jahren auch über ein Mandat der europäischen Kommission im CEN entsprechende Bauproduktnormen im Rahmen der EN 1504 erarbeitet wurden, wurde die Arbeit an einer Produktnorm für zementgebundenen Mörtel für den Bau und die Sanierung von Abwasserkanälen und -leitungen sowie Bauwerken in kommunalen Entwässerungssystemen und Kläranlagen erst im Jahr 2005 aufgenommen. Dieses Regelwerk wurde in Anlehnung an Bauprodukte für andere Anwendungsbereiche erstellt, berücksichtigt darüber hinaus aber die besonderen Anforderungen im Bereich der Abwasserkanäle und -leitungen. T2 - 3. Betonfachtagung Nord - Das Bauen mit Beton aus dem Blickwinkel der Dauerhaftigkeit und neuer Regelwerke CY - Brunswick, Germany DA - 29.09.2011 KW - Betoninstandsetzung KW - Mörtel KW - Abwasserbauwerke KW - Sanierung KW - DIN 19573 PY - 2011 SN - 978-3-7640-0544-3 SP - 175 EP - 189 AN - OPUS4-24784 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan T1 - Ganzheitliche Nachhaltigkeitsbewertung von Recyclingoptionen für mineralische Abbruchmaterialien N2 - Der Einsatz mineralischer Abbruchmaterialien und anderer Sekundärrohstoffe im Betonbau kann einen wesentlichen Beitrag zu einer nachhaltigen Ressourcenwirtschaft im Bauwesen leisten. Auf diesem Wege können diese Stoffe eine sinnvolle Verwendung finden und weitere umweltrelevante Auswirkungen (Ressourcenverbrauch, Emissionen) gemindert werden. In einem Teilprojekt des DAfStb/BMBFVerbundforschungsvorhabens „Nachhaltig Bauen mit Beton“ wurde das Einsatzpotenzial verschiedener Sekundärrohstoffe in Beton untersucht. Die Kernfrage ist, ob und inwieweit durch den Einsatz eines bestimmten Sekundärrohstoffs die Anforderungen nachhaltigen Bauens erfüllt werden. Zur Beantwortung dieser Frage wurde ein Bewertungskonzept mit einer ganzheitlichen Betrachtung von Nachhaltigkeitsaspekten ausgearbeitet. Die Ganzheitlichkeit umfasst dabei technische, ökologische und ökonomische Aspekte. Das Konzept wurde am Beispiel der bereits im Betonbau eingesetzten rezyklierten Gesteinskörnungen entwickelt. Die Bewertung erfolgt in vier Bewertungsschritten: I. Grundsätzliche Überlegungen, II. Vorteile für das nachhaltige Bauen, III. Alternative Bewertungswege und IV. Sensitivitätsanalysen. T2 - 3. Betonfachtagung Nord - Das Bauen mit Beton aus dem Blickwinkel der Dauerhaftigkeit und neuer Regelwerke CY - Braunschweig, Germany DA - 29.09.2011 KW - Nachhaltigkeit KW - Ganzheitlich KW - Beton KW - Recyclingbaustoffe KW - Sekundärrohstoffe KW - Abbruchmaterialien PY - 2011 SN - 978-3-7640-0544-3 SP - 139 EP - 160 AN - OPUS4-24785 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterhus, Lennart A1 - Rübner, Katrin A1 - Seidemann, M. T1 - Kieselsäurehaltiger Filterrückstand aus industrieller Abwasserbehandlung für den Einsatz als hydraulisches Bindemittel N2 - Reststoffe aus Kohlekraftwerken und der Metallurgie, wie Steinkohlen- und Braunkohlenflugasche, Hüttensand und Silikastaub werden bereits seit Jahren als puzzolanische und hydraulische Zusätze in Zementen, Mörteln und Betonen zur Optimierung der Eigenschaften eingesetzt. Dennoch gibt es weitestgehend ungenutzte Sekundärrohstoffquellen aus der Silikon- und Kieselsäureherstellung. Der Beitrag beschreibt Untersuchungen zur Nutzung kieselsäurehaltiger Filterrückstände aus der industriellen Abwasserbehandlung für den Einsatz als Bindemittelkomponente. Die chemisch-mineralogischen Eigenschaften der Filterrückstände, beispielsweise ein hoher Gehalt an amorpher Kieselsäure sowie eine große spezifische Oberfläche, legen eine Nutzung als puzzolanischer Bindemittelbestandteil nahe. Deshalb müssen Möglichkeiten einer Nutzung als Zusatz in Kompositzementen, Bodenverbesserungsmitteln und Spezialbindemitteln untersucht werden. Im Beitrag wird über die Stoffcharakterisierung, den Nachweis der puzzolanischen Eigenschaften und den Einfluss des Filterrückstands auf die Eigenschaften von Zementmörteln berichtet. T2 - GDCh-Fachtagung Bauchemie 2011 CY - Hamburg-Harburg, Germany DA - 06.10.2011 KW - Sekundärrohstoffe KW - Sekundäre Gesteinskörnung KW - Recycling KW - Leichtbeton PY - 2011 SN - 978-3-936028-69-0 N1 - Serientitel: GDCh-Monographien – Series title: GDCh-Monographien VL - 44 SP - 153 EP - 158 CY - Frankfurt/M. AN - OPUS4-24786 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric A1 - Gregor, Christian A1 - Bohse, Jürgen T1 - Überwachung der Fertigungsqualität von Faserverbund - Druckbehältern mittels Schallemissionsprüfung N2 - Ziel der Untersuchung ist die Validierung einer Prüfmethodik zur Sicherung der Fertigungsqualität von Faserverbund – Druckbehältern unter realen Fertigungsbedingungen. Das Verfahren basiert auf Merkmalen und zulässigen Grenzwerten, die aus Schallemissionsverläufen bei der Erstdruckprüfung abgeleitet werden. Die Methodik konnte zuvor bereits erfolgreich an Faserverbund – Druckbehältern mit metallischem Liner getestet und patentiert werden. Mit den aktuellen Untersuchungen wurde die Möglichkeit des Erkennens von Fertigungsfehlern in Kohlenstofffaser/Glasfaser – Hybriddruckbehältern mit polymerem Liner evaluiert. Dazu wurden Faserverbund – Druckbehälter mittels Schallemissionsmessung bei einer hydraulischen Erstdruckprüfung überwacht, wie sie (ohne Schallemissionsprüfung) generell zur Qualitätssicherung nach der Fertigung von Faserverbund – Druckbehältern gefordert wird. An Druckbehältern aus einer Serienproduktion wurden die Schallemissionsverläufe registriert und die mittleren Merkmalswerte sowie deren Streuung als Referenz ermittelt. Diese werden mit den Schallemissionsverläufen von Druckbehältern mit gezielt eingebrachten Fertigungsfehlern verglichen. Bei den Fertigungsfehlern handelt es sich um Fehler, die in der Serienproduktion auftreten können und mit den Methoden der herkömmlichen Qualitätssicherung schwer oder gar nicht nachzuweisen sind. Alle untersuchten Druckbehälter wurden im Anschluss an die Erstdruckprüfung auf verschiedene Weise bis zum Versagen (Leckage, Bersten) beansprucht. Damit war es möglich, den tatsächlichen Einfluss der Fertigungsfehler auf den Berstdruck bzw. das Ermüdungsverhalten der Behälter zu verifizieren und die Aussagefähigkeit des Schallemissionsverfahrens zu beurteilen. T2 - 18. Kolloquium Schallemission CY - Wetzlar, Germany DA - 27.10.2011 KW - Faserverbund-Druckbehälter KW - Schallemissionsprüfung KW - Fertigungsüberwachung PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-247881 SN - 978-3-940283-37-5 IS - DGZfP-BB 131 (Vortrag 16) SP - 1 EP - 9 AN - OPUS4-24788 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ferraioli, M. A1 - Mandara, A. A1 - Abruzzese, D. A1 - Miccoli, Lorenzo T1 - Dynamic identification and seismic safety of masonry bell towers N2 - The paper addresses two case studies of structural monitoring and seismic assessment of medieval masonry Towers in Italy: the bell tower of Aversa and the bell tower of Capua. These monuments in the Campania region were monitored by means of full-scale environmental vibration testing. Measured responses were then used for modal identification. The procedure is based on a typical finite element model updating technique based on vibration test results. Parameters optimization is carried out by minimizing a weighted error criterion relative to the building’s modal properties. A satisfactory improvement on modal parameters is thus obtained, resulting in a close Agreement between the modal properties observed in dynamic tests and those calculated from numerical model. Seismic assessment is carried out with nonlinear static analysis of the tower under multimodal distributions of lateral loads. Nonlinear analysis indicates the potential collapse mechanisms and evidences dangerous structural weakness which may play a role in the seismic vulnerability of the towers. T2 - 14th Conference of seismic engineering ANIDIS CY - Bari, Italy DA - 18.09.2011 KW - Masonry towers KW - Structural identification KW - Model updating PY - 2011 SN - 978-88-7522-040-2 IS - Abschnitt E SP - 1 EP - 10 AN - OPUS4-24839 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ferraioli, M. A1 - Abruzzese, D. A1 - Miccoli, Lorenzo A1 - Di Lauro, G. T1 - Torsional seismic response of an asymmetric-plan hospital buidling N2 - The inelastic torsional response of an asymmetric-plan hospital building is studied. The response of the structure in the time domain as recorded by highly sensitive sensor network, integrated by a data acquisition system. The identification was performed using techniques of modal extraction in the frequency domain (frequency Domain decomposition). A calibration process was applied in order to identify a reliable structural model to be used for the seismic vulnerability assessment of the hospital building. In particular, a nonlinear static procedure accounting for mass distribution, higher modes contribution and mode-shapes correlation was proposed for the estimation of the seismic response of irregular buildings. Finally, the influence of lateral force distribution, node control during pushover and accidental eccentricity is investigated. T2 - 14th Conference of seismic engineering ANIDIS CY - Bari, Italy DA - 18.09.2011 KW - Seismic response KW - Irregular buildings KW - Inelastic torsion PY - 2011 SN - 978-88-7522-040-2 IS - Abschnitt D SP - 1 EP - 10 AN - OPUS4-24840 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ballier, G. A1 - Mayer, K. A1 - Krause, Martin T1 - Ultraschallabbildung zur zerstörungsfreien Strukturbestimmung von Betonbauteilen mit Hilfe der "One-Way"-Wellengleichung T2 - DGZfP Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24841 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Friedrich, C. A1 - Krause, Martin A1 - Paehge, W. A1 - Eilers, G. T1 - In situ stress monitoring: Investigations of pressure pad coupling conditions T2 - 8th International Symposium on Field Measurement in GeoMechanics CY - Berlin, Germany DA - 2011-09-12 PY - 2011 AN - OPUS4-24843 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Takeuchi, T. A1 - Montenegro, J. A1 - Hennig, Andreas A1 - Matile, S. T1 - Pattern generation with synthetic sensing systems in lipid bilayer membranes N2 - The objective of this study was to introduce differential sensing techniques to synthetic systems that act, like olfactory receptors, as transporters in lipid bilayer membranes. Routine with most alternative chemosensing ensembles, pattern generation has, quite ironically, remained inaccessible in lipid bilayers because the number of available crossresponsive sensor components has been insufficient. To address this challenge, we here report on the use of cationic hydrazides that can react in situ with hydrophobic analytes to produce cationic amphiphiles which in turn can act as countercation activators for polyanionic transporters in fluorogenic vesicles. To expand the dimension of signals generated by this system, a small collection of small peptides containing a positive charge (guanidinium, ammonium) and one to three reactive hydrazides are prepared. Odorants are used as examples for hydrophobic analytes, perfumes to probe compatibility with complex matrices, and counterion-activated calf-thymus DNA as representative polyion–counterion transport system. Principal component and hierarchical cluster analysis of the obtained multidimensional patterns are shown to differentiate at least 21 analytes in a single score plot, discriminating also closely related structures such as enantiomers, cis–trans isomers, single-atom homologs, as well as all tested perfumes. Inverse detection provides access to analytes as small as acetone. The general nature of the introduced methodology promises to find diverse applications in current topics in biomembrane research. KW - Liposome KW - DNA KW - Biosensor KW - Principal component analysis PY - 2011 DO - https://doi.org/10.1039/c0sc00386g SN - 2041-6520 SN - 2041-6539 VL - 2 IS - 2 SP - 303 EP - 307 PB - RSC CY - Cambridge AN - OPUS4-24844 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bachmann, Marcel A1 - Avilov, Vjaceslav A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Multiphysics process simulation of the electromagnetic-supported laser beam welding N2 - A three-dimensional laminar steady state numerical model was used to investigate the influence of an alternating current (ac) magnetic field during high power laser beam keyhole welding of 20 mm thick nonferromagnetic aluminum. COMSOL Multiphysics was used to calculate the threedimensional heat transfer, fluid dynamics and electromagnetic field equations. Most important physical effects of the process were taken into account: Thermo-capillary (Marangoni) convection at the upper and lower weld pool boundaries, natural convection due to gravity and latent heat of solid-liquid phase transition. It is shown that the gravity drop-out associated with welding of thick plates due to the hydrostatic pressure can be prevented by the application of an ac magnetic field. The application of an oscillating magnetic field of 70 mT was investigated to allow for singlepass laser beam welding of thick aluminum plates. The flow pattern in the molten zone and the temperature distributions are significantly changed. T2 - COMSOL Conference 2011 CY - Ludwigsburg, Germany DA - 2011-10-26 KW - Electromagnetic weld pool support KW - Laser beam welding KW - Lorentz force KW - Marangoni stresses KW - Natural convection PY - 2011 SN - 978-0-9839688-0-1 IS - 11122 / 8567_bachmann_paper SP - 1 EP - 7 CY - Stuttgart AN - OPUS4-24845 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trappe, Volker T1 - Betriebszeitfeste Auslegung von FVK - Effekte, Grenzen, Möglichkeiten T2 - IKV-Fachtagung zur Kunststoffverarbeitung CY - Aachen, Germany DA - 2011-11-24 PY - 2011 AN - OPUS4-24846 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trappe, Volker T1 - Betriebsfestigkeitsnachweis für Segelflugzeuge aus FKV - Konzepte, Historie, Entwicklungen T2 - 35. Symposium für Segelflugzeugentwicklung, Wasserkuppe (Rhön) CY - Fulda, Germany DA - 2011-11-17 PY - 2011 AN - OPUS4-24847 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Günzel, Stephan A1 - Hickmann, Stefan A1 - Wittemeyer, Christian A1 - Trappe, Volker T1 - Einfluss der Faserorientierung und des Matrixfeuchtegehalts auf das Einzelrissfortschrittsverhalten eines kurzglasfaserverstärkten Polyamids T2 - Polymerwissenschaftliches Seminar an der TU Berlin CY - Berlin, Germany DA - 2011-11-23 PY - 2011 AN - OPUS4-24848 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Herffurth, T. A1 - Schröder, S. A1 - Tan, Ö. A1 - Apel, S. A1 - Senoner, Mathias A1 - Sahre, Mario ED - Weckenmann, A. T1 - Rauheitsbewertung beschichteter Oberflächen T2 - Abschlusskolloquium DFG Schwerpunktprogramm 1159 - Neue Strategien der Mess- und Prüftechnik für die Produktion von Mikrosystemen und Nanostrukturen CY - Erlangen, Germany DA - 2010-10-06 KW - AFM-Spitzencharakterisierer KW - Nanotopographie KW - Rasterkraftmikroskopie KW - Rauheit KW - Weißlichtinterferometrie PY - 2011 SN - 978-3-8440-0358-1 SN - 0945-0769 SP - 219 EP - 231 PB - Shaker Verlag GmbH AN - OPUS4-24789 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Senoner, Mathias A1 - Sahre, Mario A1 - Rooch, Heidemarie A1 - Unger, Wolfgang ED - Weckenmann, A. T1 - Neuartige, räumlich strukturierte Testproben für die Bestimmung der Abbildungsqualität und die Kalibrierung der Längenskala in der Rastersondenmikroskopie T2 - Abschlusskolloquium DFG Schwerpunktprogramm 1159 - Neue Strategien der Mess- und Prüftechnik für die Produktion von Mikrosystemen und Nanostrukturen CY - Erlangen, Germany DA - 2010-10-06 KW - MOVPE KW - Rasterkraftmikroskopie KW - Referenzmaterial KW - Schichtstapel KW - Selektives Ätzen KW - Spitzencharakterisierer KW - TEM PY - 2011 SN - 978-3-8440-0358-1 SN - 0945-0769 SP - 116 EP - 129 PB - Shaker Verlag GmbH AN - OPUS4-24790 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Masuck, I. A1 - Hutzler, C. A1 - Jann, Oliver A1 - Luch, A. T1 - Inhalation exposure of children to fragrances present in scented toys N2 - When utilized in the perfuming of children's toys, fragrances capable of inducing contact allergy in human skin may also become bioavailable to children via the inhalation route. The aim of this study was to determine the area-specific emission rates of 24 fragrances from a plasticized PVC reference material that was meant to mimic a real plastic toy. This material was introduced into an emission chamber for 28 days at handling conditions or at worst-case conditions. As a result, fragrances can be separated into three categories according to their emission rates ranging from 0.0041 to 16.2 mg/m² × h, i.e., highly volatile, semivolatile, and low-volatile compounds. Compounds of the first and second categories were monitored with decreasing emission rates. Substances of the third category were detected with increasing emission rates over time. Further, higher temperatures led to higher emission rates. The emission concentration of fragrances from four real scented toys varied between 1.10 and 107 µg/m³ at day 1 in the test chamber. Therefore, short-term inhalation exposure to fragrances originating from toys was in the range of 0.53–2700 ng/kg BW/d for the children of age 1 and older. Long-term exposure to these fragrances was calculated in the range of 2.2–220 ng/kg BW/d. KW - Scented toys KW - Fragrance allergens KW - Inhalation exposure KW - Emission chamber KW - Volatile organic compounds PY - 2011 DO - https://doi.org/10.1111/j.1600-0668.2011.00727.x SN - 0905-6947 SN - 1600-0668 VL - 21 IS - 6 SP - 501 EP - 511 PB - Danish Techn. Pr. CY - Copenhagen AN - OPUS4-24791 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühne, Hans-Carsten A1 - Ünal, Murat T1 - Entwicklung von Instandsetzungsstrategien zur Restaurierung von Betonglasfenstern - Schadensprozesse und Lösungsansätze - T2 - Kolloquium Betonglasrestaurierung CY - Paderborn, Germany DA - 2011-10-10 PY - 2011 AN - OPUS4-24794 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Natural Stone Reprofiling in Cultural Heritage with Modular Repair Mortars T2 - 2nd WTA-international PhD Symposium CY - Brno, Czech Republic DA - 2011-10-06 PY - 2011 AN - OPUS4-24795 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubcová, Petra A1 - Rübner, Katrin A1 - Schnell, A. T1 - Leichte Gesteinskörnungen auf der Basis thermischer und hydrothermal hergestellter Blähgranulate aus Abbruchabfällen T2 - 15. Seminar "Beschichtungen und Bauchemie" CY - Kassel, Germany DA - 2011-11-29 PY - 2011 AN - OPUS4-24796 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ünal, Murat A1 - Kühne, Hans-Carsten T1 - Entwicklung von Betonergänzungsmassen und Probekörpern zur Instandsetzung von Betonglasfenstern - Projektergebnisse Beglares - T2 - Kolloquium Betonglasrestaurierung CY - Paderborn, Germany DA - 2011-10-10 PY - 2011 AN - OPUS4-24797 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Golze, Manfred T1 - EUROLAB's TCQA and its contributions to reliable test results T2 - 4. Internationale CROLAB Konferenz CY - Cavtat, Croatia DA - 2011-10-10 PY - 2011 AN - OPUS4-24798 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hedrich, Martina T1 - Teaching QM and Metrology in Analytical Chemistry - Fit for Profession? T2 - EUROanalysis 2011 CY - Belgrade, Serbia DA - 2011-09-11 PY - 2011 AN - OPUS4-24799 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute A1 - Behnke, Thomas A1 - Würth, Christian A1 - Pauli, Jutta A1 - Hoffmann, Katrin A1 - Hoffmann, Angelika T1 - New flourescence standards for the NIR T2 - MAF 12 CY - Strasbourg, France DA - 2011-09-11 PY - 2011 AN - OPUS4-24800 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krause, Martin A1 - Chinta, P.K. A1 - Mayer, K. A1 - Effner, Ute A1 - Müller, Sabine T1 - NDT of Structural Timber Members by means of 3D Ultrasonic Imaging Techniques and Modelling T2 - NDTMS 2011 CY - Istanbul, Turkey DA - 2011-05-15 PY - 2011 AN - OPUS4-24801 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Streicher, Doreen A1 - Paetsch, O. A1 - Seiler, R. A1 - Prohaska, S. A1 - Krause, Martin A1 - Boller, C. T1 - 3-D-Visualisierung von Radar- und Ultraschallecho-Daten mit ZIBAmira T2 - DGZfP Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24802 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gümpel, P. A1 - Leu, F. A1 - Burkert, Andreas A1 - Lehmann, Jens T1 - Corrosion resistance of lean alloy alternatives for 300 series stainless steels N2 - Rising Prices of nickel and molybdenum in the past few years have led to unprecedented interest in Substitution of leaner-content alloys for Standard 300-series austenitic stainless steels in a lot of applications. Due to the high prices of different alloying elements and to periodic large fluctuations that cause similar large fluctuations in the costs of using 300-series stainless steels; a lot of new materials entered the markets in Europe and also in the rest of the world. A big disadvantage consists in the fact that there are though corrosion results that, however, a direct comparison of the corrosion resistance of these new materials does not exist up to now or only incompletely. In this project comparative investigations were carried out and always one or several representatives of a material group were incorporated. These material groups are: Lean Duplex Stainless Steels, Manganese Alloyed Austenitic and Duplex Stainless Steels and Ferritic Stainless Steels. These materials were investigated in a lot of different test procedures and in different conditions focused on the application in civil engineering and common use. Beside the electrochemical investigations all materials were exposed in different surface States in the atmosphere, once in Coastal nearness and once in a city centre area. Other exposition tests with material Coupons where done in the atmosphere of indoor swimming pools and at the case of food processing machines were corrosion processes are caused by the cleaning procedure. First results are reported. T2 - 7th European stainless steel conference - science and market CY - Como, Italy DA - 21.09.2011 KW - Austenitic stainless steels KW - Ferritic stainless steels KW - Duplex stainless steels KW - Manganese alloyed stainless steels KW - Pitting corrosion KW - Stress corrosion cracking KW - Passive layer KW - Surface condition PY - 2011 SN - 978-88-85298-84-2 IS - Applications / No. 53 SP - 1 EP - 15 AN - OPUS4-24803 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz ED - Náprstek, J. ED - Horácek, J. ED - Okrouhlík, M. ED - Marvalová, B. ED - Verhulst, F. ED - Sawicki, J.T. T1 - Reducing ground-borne micro-vibrations by plate foundations T2 - Vibration problems ICOVP 2011 - 10th international conference on vibration problems CY - Prague, Czech Republic DA - 2011-09-05 KW - Plate-soil interaction KW - Wave excitation KW - Vibration reduction KW - Finite-element boundary-element method PY - 2011 SN - 978-94-007-2068-8 SN - 0930-8989 N1 - Serientitel: Springer proceedings in physics – Series title: Springer proceedings in physics VL - 139 SP - 329 EP - 335 PB - Springer AN - OPUS4-24804 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino A1 - Burkert, Andreas A1 - Meinel, Dietmar ED - Rogge, A. ED - Meng, B. T1 - Neue Verfahren zur Untersuchung chloridinduzierter Lochkorrosion an Stahl in Beton N2 - Die Kombination elektrochemischer und computertomographischer Untersuchungs-Verfahren bietet die Möglichkeit, elektrochemische Messungen zerstörungsfrei verifizieren und richtig interpretieren zu können. Die Ermittlung der durch Lochkorrosion geschädigten Stahloberflächen ermöglicht es Probekörper zu entwickeln, die ein der Praxis entsprechendes Schadensbild aufweisen. Ein weiterer Vorteil stellt sich in der Minimierung der Probenmatrix dar. Die klassische Versuchsdurchführung erfordert die Zerstörung von Proben nach jeder Vorschädigungsstufe. Dies kann durch den Einsatz der Computertomografie vermieden werden. Die elektrochemischen Messwerte können flächenbezogen ermittelt werden, solange sich die Korrosionserscheinungen vollständig innerhalb des durch die CT abgebildeten Untersuchungsbereiches befinden. T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Germany DA - 07.11.2011 KW - Betonstahl KW - Korrosion KW - Lochkorrosion KW - Computertomographie PY - 2011 SN - 978-3-9814281-0-0 IS - G6 SP - 262 EP - 271 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-24805 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Ebell, Gino A1 - Lehmann, Jens ED - Rogge, A. ED - Meng, B. T1 - Einfluss chromatreduzierter Zemente auf die Ausbildung der Verbundzone Stahl/Beton bei Verwendung feuerverzinkter Bauteile N2 - Durch die Absenkung des Chromatgehaltes der Zemente verändern sich die elektrochemischen Reaktionen von verzinkten Betonstählen in der Frischbetonphase. Mit Hilfe von elektrochemischen Messungen sowie Stabauszugsversuchen wurde an chromathaltigen und chromatreduzierten Zementen die Auswirkung des Chromats auf die Deckschichtbildung am Zink und auf das Verbundverhalten untersucht. Mit den Ergebnissen konnte eine Beeinträchtigung der Verbundzone als Folge der Chromatreduzierung für die Zementarten CEM I und CEM II nachgewiesen werden. Die Störung der Verbundzone ist in Bezug auf die sich ausbildende Porenstruktur als dauerhaft anzusehen. Die Auswirkungen auf das Verbundverhalten werden mit zunehmendem Betonalter weitgehend kompensiert. Die Ergebnisse der bezogenen Verbundspannung bei Verschiebewegen von 0,1 mm und 0,5 mm liegen trotz der Gefügestörung noch im Bereich der Erwartungswerte für den unverzinkten Betonstahl. Unter baupraktischen Gesichtspunkten muss die auftretende Gefügestörung hinsichtlich der Verbundspannung daher keine Berücksichtigung finden. T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Germany DA - 07.11.2011 KW - Betonstahl KW - Chromat KW - Feuerverzinkt KW - Verzinkt KW - Zement KW - Chromatreduziert PY - 2011 SN - 978-3-9814281-0-0 IS - G7 SP - 272 EP - 282 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-24806 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz A1 - Said, Samir ED - Zhai, W. ED - Takemiya, H. ED - De Roeck, G. ED - Tutumluer, E. T1 - Experimental soil parameters by different evaluation methods for impulsive, train and ambient excitation T2 - ISEV 2011 - 5th International symposium on environmental vibration - Advances in environmental vibration CY - Chengdu, China DA - 2011-10-20 KW - Wave velocity KW - Dispersion KW - SASW KW - MASW KW - SPAC KW - Damping PY - 2011 SN - 978-7-03-032373-6 SP - 3 EP - 9 PB - Science Press AN - OPUS4-24807 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian T1 - Interfacial Failure in Composites under Transverse Loading T2 - 15th Meeting on Composites Materials and Structures CY - Haifa, Israel DA - 2011-11-15 PY - 2011 AN - OPUS4-24808 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterhus, Lennart A1 - Rübner, Katrin T1 - Kieselsäurehaltiger Filterrückstand aus industrieller Abwasserbehandlung für den Einsatz als hydraulisches Bindemittel N2 - - 5.000 bis 10.000 t wasserhaltiger Filterrückstand (FR) entstehen jährlich pro Produzent bei der Neutralisation der Abwässer aus der Silicon- oder Kieselsäureherstellung - Anfall als fester, feuchter, schollenartiger Filterkuchen - Verwertung heute: Deponierung, Tagebauverfüllung -> ungenutzte Sekundärrohstoffquelle - Untersuchung der Einsatzmöglichkeiten der aufbereiteten Filterrückstände zur Eigenschaftsverbesserung zementgebundener Baustoffe analog der wohlbekannten Anwendung von hochdisperser Kieselsäure und Silicastaub T2 - GDCh-Tagung Bauchemie CY - Hamburg, Germany DA - 06.10.2011 PY - 2011 AN - OPUS4-24819 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Askar, Enis A1 - Holtappels, Kai T1 - Messunsicherheit bei der Bestimmung von Explosionsgrenzen T2 - 5. Fachtagung "Messunsicherheit praxisgerecht bestimmen" CY - Erfurt, Germany DA - 2011-11-08 PY - 2011 AN - OPUS4-24821 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hennecke, Manfred T1 - Innovation und Sicherheit im Staatsauftrag: Aus der Arbeit der BAM T2 - 67. Kolloquium für Wärmebehandlung, Werkstofftechnik, Fertigungs- und Verfahrenstechnik CY - Wiesbaden, Germany DA - 2011-10-13 PY - 2011 AN - OPUS4-24822 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hennecke, Manfred T1 - Akkreditierung im Wandel T2 - 1. Nationale Akkreditierungskonferenz CY - Berlin, Germany DA - 2011-06-08 PY - 2011 AN - OPUS4-24823 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hennecke, Manfred T1 - Chemiker im öffentlichen Dienst T2 - Jungchemikerforum der Gesellschaft Deutscher Chemiker an der Universität Kaiserslautern CY - Kaiserslautern, Germany DA - 2011-05-08 PY - 2011 AN - OPUS4-24824 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hennecke, Manfred T1 - Nanoscience in der BAM T2 - Kolloquium am Institut für Mikromechanik (IMM) CY - Mainz, Germany DA - 2011-10-25 PY - 2011 AN - OPUS4-24825 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Beck, Uwe A1 - Hertwig, Andreas A1 - Kormunda, M. A1 - Krause, Andreas A1 - Krüger, Hannes A1 - Lohse, Volkmar A1 - Nooke, Alida A1 - Pavlik, J. A1 - Steinbach, J. T1 - SPR enhanced ellipsometric gas monitoring on thin iron doped tin oxide layers N2 - In this work, thin iron doped tin oxide layers (3–6 nm) were investigated with regard to gas sensitivity by means of surface plasmon resonance (SPR) effect with ellipsometric readout. The experimental set-up was a Kretschmann configuration with gold as metal layer. The sensor system was exposed to different concentrations of methane in the low ppm range and the sensor response of an uncoated gold layer compared to a gold layer coated with iron doped tin oxide. The additional layer effects stability with regard to drift behavior of the sensor and an increase in sensitivity. Furthermore, the sensor is able to detect the toxic gas carbon monoxide in low concentration range (down to 0.5 ppm). The thin layers were investigated by X-ray photoelectron spectroscopy, secondary electron microscopy and spectroscopic ellipsometry. The possible mechanisms taking place on the surface are discussed. KW - Gas sensing KW - SPR effect KW - Iron doped tin oxide KW - Ellipsometry PY - 2011 DO - https://doi.org/10.1016/j.snb.2011.08.036 SN - 0925-4005 SN - 1873-3077 VL - 160 IS - 1 SP - 609 EP - 615 PB - Elsevier CY - Amsterdam [u.a.] AN - OPUS4-24826 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Baytekin, H. Tarik A1 - Oran, Umut A1 - Theisen, J. A1 - Schmidt, Martin A1 - Unger, Wolfgang ED - Weckenmann, A. T1 - Validierte Messverfahren für die nichtgeometrische Größe Hydrophilie - Anwendung in der Mikrofluidik T2 - Abschlusskolloquium DFG Schwerpunktprogramm 1159 - Neue Strategien der Mess- und Prüftechnik für die Produktion von Mikrosystemen und Nanostrukturen CY - Erlangen, Deutschland DA - 2010-10-06 PY - 2011 SN - 978-3-8440-0358-1 SN - 0945-0769 SP - 163 EP - 172 PB - Shaker Verlag GmbH AN - OPUS4-24827 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander A1 - Krebber, Katerina T1 - Simultaneous measurement of temperature and strain distribution using Brillouin scattering in dispersion-shifted fibers N2 - We studied Brillouin gain spectrum characteristics in dispersion-shifted fibers having compound GeO2-doping compositions in the fiber core to realize simultaneous measurement of distributed strain and temperature. Due to various dopant concentration alongside the radius of tested nonzero dispersion-shifted fibers several multiple Brillouin scattering resonances were observed in the stimulated Brillouin spectra arose through backscattering on higher acoustic modes which propagated along the fiber axis. As a result of the varying acoustic velocities, the Brillouin resonance peaks featured different temperature coefficients which can be used to accomplish the simultaneous measurement of fiber strain and temperature. We presented our first measurement results for NZDS Fujikura and LEAF Corning fiber and discussed the superior sensory suitability of the former fiber types. T2 - IEEE Sensors 2011 conference CY - Limerick, Ireland DA - 28.10.2011 KW - Fiber optic sensor KW - Spatial distributed sensor KW - Brillouin gain spectrum (BGS) KW - Nonzero dispersion-shifted fiber (NZDSF) KW - Brillouin sensor KW - BOTDA KW - BOFDA PY - 2011 SN - 978-1-4244-9288-6 SP - 1476 EP - 1479 AN - OPUS4-24828 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shcheglov, Pavel A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael A1 - Petrovskiy, V. T1 - Condensed metal particles influence on the process of high power fiber laser thick metal welding T2 - 22th International Conference "Laser in Science, Technology, Medicine" CY - Gelendzhik, Russia DA - 2011-09-20 PY - 2011 AN - OPUS4-24769 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shcheglov, Pavel A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael A1 - Uspenskiy, S. A1 - Petrovskiy, V. A1 - Yermachenko, V. M. T1 - Influence of the welding plume on laser rediation during high power fiber laser welding T2 - 20th International Laser Physics Workshop LHPYS`11 CY - Sarajevo, Bosnia and Herzegovina DA - 2011-07-11 PY - 2011 AN - OPUS4-24770 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shcheglov, Pavel A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Plume investigation during high power fiber laser welding T2 - The Fifth International Conference "Laser TEchnologies in Welding and Materials Processing" CY - Crimea, Ukraine DA - 2011-05-24 PY - 2011 AN - OPUS4-24771 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shcheglov, Pavel A1 - Uspenskiy, S. A1 - Petrovskiy, V. A1 - Yermachenko, V. M. T1 - Line and continuum emission spectroscopy of the high power ytterbium fiber laser welding plume under Ar and He shielding atmosphere T2 - 20th International Laser Physics Workshop LHPYS`11 CY - Sarajevo, Bosnia and Herzegovina DA - 2011-07-11 PY - 2011 AN - OPUS4-24772 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feistkorn, Sascha T1 - Die POD - eine Vorgehensweise zum Gütenachweis qualitativer zerstörungsfreier Prüfverfahren im Bauwesen T2 - DGZfP Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24773 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiggenhauser, Herbert A1 - Kind, Thomas A1 - Wöstmann, Jens A1 - Behrens, Matthias A1 - Borchardt, Kerstin A1 - Milmann, Boris A1 - Stoppel, Markus A1 - Kurz, J. T1 - Zerstörungsfreie Prüfung im Bauwesen - 3 Fallstudien: - Automatisierte Prüfung großer Flächen - Bestimmung von Spanngliedlagen - Untersuchungen an der Florisdorfer Brücke T2 - FSV Seminar Brückenprüfer - Erfahrungsaustausch CY - Vienna, Austria DA - 2011-11-22 PY - 2011 AN - OPUS4-24774 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liehr, Sascha A1 - Krebber, Katerina T1 - A novel quasi-distributed long-gauge fiber optic strain sensor system for dynamic measurement T2 - 8th International Conference on Structural Dynamics, EURODYN 2011 CY - Leuven, Belgium DA - 2011-07-04 PY - 2011 AN - OPUS4-24776 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liehr, Sascha T1 - Hangüberwachung mit optischen Polymerfasern T2 - VDI/VDE-GMA Expertenforum "Strukturmonitoring und Zustandsüberwachung 2011" CY - Nuremberg, Germany DA - 2011-06-07 PY - 2011 AN - OPUS4-24777 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quillard, S. A1 - Gildenhaar, Renate A1 - Berger, Georg A1 - Mellier, C. A1 - Hervelin, J. A1 - Deniard, P. T1 - Raman and infrared studies of substituted ß-TCP T2 - 23rd. Symp. and Annual Meeting of Intern. Soc. for Ceramics in Medicine (ISCM) CY - Istanbul, Turkey DA - 2011-11-06 PY - 2011 AN - OPUS4-24859 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Becker, Anika A1 - Laurich, St. A1 - Sommer, U. A1 - Alt, V. A1 - Bühring-Polaczek, A. A1 - Guillen, T. A1 - Ploska, Ute T1 - Experimentelle Untersuchungen einer gegossenen offenporigen Titanstruktur mit biologischer Reaktionsschicht im Rattenmodell T2 - Jahrestagung der Dt. Ges. für Biomaterialien CY - Giessen, Germany DA - 2011-11-10 PY - 2011 AN - OPUS4-24860 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dombrowski, Felix A1 - Hoffmann, Rita A1 - Marx, Heidi A1 - Ploska, Ute A1 - Berger, Georg T1 - Investigations on degradable and figuline calcium alkaline phosphate cements with multimodal particle size distribution T2 - Bioceramics 23, 23rd. Anual Meeting of Intern. Soc. for Ceramics in Medicine (ISCM) CY - Istanbul, Turkey DA - 2011-11-04 PY - 2011 AN - OPUS4-24861 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dombrowski, Felix A1 - Hoffmann, Rita A1 - Marx, Heidi A1 - Ploska, Ute A1 - Berger, Georg T1 - Solubility and ingrowth behavior of degradable and figuline calcium alkaline phosphate cements T2 - Bioceramics 23, 23rd. Anual Meeting of Intern. Soc. for Ceramics in Medicine (ISCM) CY - Istanbul, Turkey DA - 2011-11-04 PY - 2011 AN - OPUS4-24862 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gildenhaar, Renate A1 - Wirth, Cynthia A1 - Linow, Ulf A1 - Berger, Georg A1 - Houshmand, A. A1 - Knabe, C. T1 - Calcium alkaline phosphate scaffolds for bone regeneration 3D-fabricated by additive manufacturing T2 - 23rd Symp. and Annual Meeting of Intern. Soc. for Ceramics in Medicine (ISCM) CY - Istanbul, Turkey DA - 2011-11-04 PY - 2011 N1 - Geburtsname von Wirth, Cynthia: Gomes, C. M. - Birth name of Wirth, Cynthia: Gomes, C. M. AN - OPUS4-24863 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Becker, Anika A1 - Sommer, U. A1 - Hagemann, K. A1 - Bühring-Polaczek, A. A1 - Guillen, T. A1 - Ohrndorf, A. A1 - Ploska, Ute A1 - Berger, Georg T1 - Experimentelle Untersuchungen einer gegossenen Titanstruktur mit biologischer Reaktionsschicht in vitro T2 - Jahrestagung der Dt. Ges. für Biomaterialien CY - Giessen, Germany DA - 2011-11-10 PY - 2011 AN - OPUS4-24864 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Töpfer, J. A1 - Hesse, J. A1 - Barth, S. A1 - Pawlowski, B. A1 - Rabe, Torsten T1 - Spinel Ferrites for Integrated LTCC Inductor Modules T2 - EUROMAT CY - Montpellier, France DA - 2011-09-12 PY - 2011 AN - OPUS4-24865 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gemeinert, Marion T1 - Fügeverbindungen für Mikrosensoren auf Basis von niedrig sinternden Submikron-Silberpasten T2 - Kolloquium des Ferdinand-Braun-Instituts für Höchstfrequenztechnik CY - Berlin, Germany DA - 2011-11-18 PY - 2011 AN - OPUS4-24866 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naghib Zadeh, Hamid A1 - Rabe, Torsten A1 - Töpfer, J. A1 - Karmazin, R. T1 - Co-Firing of LTCC Modules with Embedded Ferrite Layers T2 - European Microelectronics Packaging Conference CY - Brighton, England DA - 2011-09-12 PY - 2011 AN - OPUS4-24867 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabe, Torsten A1 - Klobes, Peter A1 - Kuchenbecker, Petra A1 - Schiller, W. T1 - Porenbewertung an grünen Folien und Laminaten mittels Hg-Porosimetrie T2 - eingeladener Vortrag zum DKG/DGM Symposium "Charakterisierungsverfahren in der keramischen Aufbereitung: Vom Pulver bis zum Grünkörper" CY - Erlangen, Germany DA - 2011-11-29 PY - 2011 AN - OPUS4-24868 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröder, Volkmar T1 - Forschungsergebnisse der BAM zu den Explosionsgrenzen von Biogas T2 - 1. Kolloquium Anlagensicherheit/Störfallvorsorge: "Stand der Sicherheitstechnik bei Biogasanlagen" im Sächsischen Landesamt für Umwelt CY - Dresden, Germany DA - 2011-11-23 PY - 2011 AN - OPUS4-24849 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schendler, Thomas T1 - Das Merkblatt für Biogasanlagen sowie Aufgaben der Kommission für Anlagensicherheit (KAS) T2 - 1. Kolloquium Anlagensicherheit/Störfallvorsorge: "Stand der Sicherheitstechnik bei Biogasanlagen" CY - Dresden, Germany DA - 2011-11-23 PY - 2011 AN - OPUS4-24850 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hennecke, Manfred T1 - Über Innovationen: Bedingungen, Förderndes, Bremsendes T2 - Festkolloquium der Deutschen Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin, Germany DA - 2011-01-14 PY - 2011 AN - OPUS4-24858 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krebber, Katerina T1 - Structural health monitoring by smart technical textiles based on fiber optic sensors T2 - International Conference on Structural Health Monitoring of Intelligent Infrastructure, SHMII-5 CY - Cancún, Mexico DA - 2011-12-11 PY - 2011 AN - OPUS4-24960 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander A1 - Krebber, Katerina T1 - Simultaneous measurement of temperature and strain distribution using Brillouin scattering in dispersion-shifted fibers T2 - IEEE SENSORS 2011 Conference CY - Limerick, Ireland DA - 2011-10-28 PY - 2011 AN - OPUS4-24961 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander T1 - Fiber optic system for monitoring large earth structures T2 - 2nd Workshop UrbanFlood 2011 CY - Amsterdam, Netherlands DA - 2011-11-03 PY - 2011 AN - OPUS4-24962 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Polatajko, A. A1 - Feldmann, I. A1 - Hayen, H. A1 - Jakubowski, Norbert T1 - Combined application of a laser ablation-ICP-MS assay for screening and ESI-FTICR-MS for identification of a Cd-binding protein in Spinacia oleracea L. after exposure to Cd N2 - We have studied the binding of the toxic element Cd to plant proteins and have used for this purpose spinach (Spinacia oleracea L.) plants treated with 50 µM Cd(II) as a model system. Laser ablation ICP-MS has been applied for the screening of Cd-binding proteins after separation by native anodal polyacrylamide gel electrophoresis (AN-PAGE) and electroblotting onto membranes. The main Cd-carrying protein band was isolated and investigated by nano-electrospray ionization–Fourier transform ion cyclotron resonance (FTICR) mass spectrometry after tryptic digestion. By this procedure, the main Cd-binding protein was identified as ribulose-1,5-bisphosphate carboxylase/oxygenase (RuBisCO). The latter enzyme has been discussed in the literature to be affected in its activity by oxidative stress induced by Cd. However, in this paper it is demonstrated for the first time that RuBisCO directly binds Cd and thus may be directly altered by this toxic element. A commercially available protein standard was used to verify direct binding of Cd(II) to the protein, even without metabolisation. The resulting metal–protein complex was shown to be stable enough to survive AN-PAGE separation and electroblotting. By the use of size exclusion chromatography coupled with ICP-MS it was demonstrated that the RuBisCO protein standard shows similar metal binding properties to Cd. Furthermore, essential elements such as Mn(II), Fe(II) and Cu(II), which are known to possibly replace the RuBisCO activator Mg(II), were investigated in addition to Zn(II). Again, similar binding properties in comparison to the plant protein were observed. PY - 2011 DO - https://doi.org/10.1039/c1mt00051a SN - 1756-5901 SN - 1756-591X VL - 3 IS - 10 SP - 1001 EP - 1008 PB - RSC Publ. CY - Cambridge AN - OPUS4-24963 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Olbricht, Jürgen A1 - Yawny, A. A1 - Pelegrina, J.L. A1 - Dlouhy, A. A1 - Eggeler, G. T1 - On the stress-induced formation of R-phase in ultra-fine-grained Ni-Rich NiTi shape memory alloys N2 - Phase transformations in binary ultra-fine-grained (UFG) pseudoelastic NiTi wires were studied in a wide temperature range using mechanical loading/unloading experiments, resistance measurements, differential scanning calorimetry (DSC), thermal infrared imaging, and transmission electron microscopy (TEM). The formation of R-phase can be detected in the mechanical experiments. It is shown that the stress-strain response of the R-phase can be isolated from the overall stress-strain data. The R-phase always forms prior to B19¢ when good pseudoelastic properties are observed. The stress-induced B2 to R-phase transition occurs in a homogeneous manner, contrary to the localized character of the B2/R to B19' transformations. The temperature dependence of the critical stress values for the formation of the martensitic phases shows a Clausius Clapeyron type of behavior with constants close to 6 MPa/K (B19') and 18 MPa/K (R-phase). A stress-temperature map is suggested that summarizes the experimentally observed sequences of elementary transformation/deformation processes. KW - Phase transformation KW - Shape memory KW - Pseudoelasticity KW - NiTi KW - R-phase PY - 2011 DO - https://doi.org/10.1007/s11661-011-0679-y SN - 1073-5623 SN - 1543-1940 VL - 42A IS - 9 SP - 2556 EP - 2574 PB - The Minerals, Metals and Materials Society CY - Warrendale AN - OPUS4-24968 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Skrotzki, Birgit A1 - Kühn, Hans-Joachim ED - Grellmann, W. T1 - Kennwertermittlung aus statischen und zyklischen Versuchen bei erhöhter Temperatur unter isothermer und nicht isothermer Beanspruchung T2 - DVM-Tagung Werkstoffprüfung 2011 - Neue Entwicklungen in der Werkstoffprüfung - Herausforderungen an die Kennwertermittlung CY - Berlin, Germany DA - 2011-12-01 KW - Kennwert KW - Temperatur KW - E-Modul KW - Warmzugversuch KW - Ermüdung KW - Mechanical properties KW - Temperature KW - Young´s modulus KW - Elevated temperature tensile test KW - Fatigue PY - 2011 SN - 978-3-9814516-1-0 SN - 1861-8154 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 643 SP - 37 EP - 44 AN - OPUS4-24969 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lenke, Philipp A1 - Wendt, Mario A1 - Krebber, Katerina A1 - Glötzl, R. ED - Bock, W.J. ED - Albert, J. ED - Bao, X. T1 - Highly sensitive fiber optic inclinometer - easy to transport and easy to install N2 - We present the status of our work on a tube shaped 3D deformation sensor based on continuously distributed fiber optic sensing. A sensor tube of very large diameter is used to ensure high sensitivity while the transportability and applicability are still comfortable due to our application strategy. The setup is designed to use different measurement techniques in the applied optical fibers including Brillouin based measurements and interferometric optical frequency domain measurements using an OBR 4400 from Luna Technologies. T2 - 21st International conference on optical fiber sensors (OFS 21) CY - Ottawa, Canada DA - 15.05.2011 KW - Inclinometer KW - Bend KW - Sensor KW - Fiber KW - Optic KW - Brillouin KW - OBR PY - 2011 SN - 0277-786X N1 - Serientitel: Proceedings of SPIE – Series title: Proceedings of SPIE VL - 7753 SP - 775352-1 EP - 775352-4 AN - OPUS4-24970 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias A1 - Schulz, Sebastian A1 - Stark, Wolfgang A1 - Wolff, Dietmar T1 - Characterization of the low temperature behaviour of rubber sealing materials N2 - Rubbers are often used for seal applications due to their special material properties and easy use. In many applications the material is exposed to low temperatures during Operation. Therefore it is important to know the material behavior at low temperatures to determine the temperature ränge that allows a Safe Operation of the seal, e.g. in storage and transport Containers for radioactive materials. The seal function of an elastomer is limited in temperature by the rubber-glass transition during which the material properties change from rubber-like to stiff and glass-like. For a given application this correlation is not trivial and therefore needs an in-depth investigation under consideration of the physical properties and the application conditions. In this work different analytical methods are used to characterize the material behavior at low temperature in the ränge of the glass-rubber-transition and are compared with the quality of Operation of a component which is here defined by the detected leakage rate. T2 - Technomer 2011 - 22. Fachtagung über Verarbeitung und Anwendung von Polymeren CY - Chemnitz, Deutschland DA - 10.11.2011 PY - 2011 SN - 978-3-939382-10-2 IS - Kap. 3.7 SP - 1 EP - 4 AN - OPUS4-24971 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schwarzer, Stefanie A1 - Weltschev, Margit A1 - Otremba, Frank T1 - Lebensdauer und Schadensursachen von Tankcontainern, Tankfahrzeugen und Kesselwagen zur Beförderung von Gefahrgütern in der Praxis N2 - Daten über Schadensursachen und die tatsächliche Nutzungsdauer der Tanks zum Transport von Gefahrgütern liegen nur in begrenztem Maße vor. Auf der Basis der Daten von Tankbaufirmen, Speditionen und Eisenbahnkesselwagen-Vermietgesellschaften wurde die durchschnittliche Lebensdauer von Tankcontainern, Tankfahrzeugen und Kesselwagen zur Beförderung von Gefahrgütern in der Praxis ermittelt und die Hauptschadensursachen analysiert. Korrosion, Risse an Schweißnähten, Gestaltungs- und Dimensionierungsfehler sowie fertigungs- und betriebsbedingte Fehler zählen zu den Hauptschadensursachen. Viele Tanks werden vor Ablauf ihrer Nutzungsdauer nicht mehr für den Transport von Gefahrgütern eingesetzt, da sie nicht mehr den geänderten gesetzlichen Anforderungen in den Gefahrgutvorschriften entsprechen. Die Voraussagen durch Literaturangaben und Ergebnisse von Korrosionsversuchen in der BAM-Liste – Anforderungen an Tanks zur Beförderung gefährlicher Güter – spiegeln sich in der Nutzungsdauer/Lebensdauer der Tanks wider. KW - Gefahrguttransport KW - Tankcontainer KW - Tankfahrzeuge KW - Eisenbahnkesselwagen KW - Schadensursachen KW - Lebensdauer PY - 2011 SN - 2191-0073 VL - 1 IS - 11/12 SP - 28 EP - 33 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-24972 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ostermann, Markus A1 - Kühn, Andreas A1 - Bjeoumikhov, A. A1 - Wedell, R. T1 - Einsatz der Röntgenfluoreszenzanalyse in der Prozessanalytik N2 - Elementanalyse mit Röntgenfluoreszenzspektrometrie direkt am Materialstrom in Produktionsprozessen gewinnt zunehmend an Bedeutung. Die Röntgenfluoreszenzspektrometrie kann aufgrund der technischen Entwicklung mittlerweile ohne aufwändige Probenvorbereitung als aussagekräftige Informationsquelle für Stoffparameter im industriellen Prozess eingesetzt werden. Der Einsatz von online Röntgenfluoreszenzanalyse zahlt sich sowohl finanziell als auch zeitlich schnell aus, da sie sowohl für den ökonomischen Einsatz von Rohmaterialien, als auch z. B. im Materialrecycling zu gebrauchen ist. In diesem Beitrag werden vier unterschiedliche Einsatzmöglichkeiten beschrieben. N2 - Elemental analysis directly at the material stream of production processes using X-ray fluorescence spectrometry is gathering importance. Thanks to technical developments, X-ray fluorescence analysis can be used as information source in the elemental analysis of material in industrial processes without tedious sample preparation steps. The employment of online X-ray fluorescence analysis pays off both in financial as well in time aspects, since it can be used for the economic application of raw materials or e. g. for recycling. This paper describes four different applications of X-ray fluorescence spectroscopy. KW - Röntgenfluoreszenzspektrometrie KW - Stoffparameter KW - Materialanalyse KW - X-ray fluorescence spectrometry KW - Elemental analysis KW - Material analysis PY - 2011 DO - https://doi.org/10.1524/teme.2011.0162 SN - 0340-837X SN - 0178-2312 SN - 0171-8096 VL - 78 IS - 12 SP - 559 EP - 568 PB - Oldenbourg CY - München AN - OPUS4-24973 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Staude, Andreas A1 - Goebbels, Jürgen T1 - Ortsauflösung in der Computertomographie - Vergleich von MTF und Linienpaarstrukturen N2 - Anhand von Messungen an geeigneten Prüfkörpern werden die beiden etablierten Verfahren zur Bestimmung der räumlichen Auflösung von CTDaten (MTF und Kontrast von Linienpaaren), wie in den entsprechenden Normen beschrieben, durchgeführt und ihre Ergebnisse verglichen. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-249775 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Mo.3.B.1) SP - 1 EP - 10 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-24977 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Subaric-Leitis, Andreas A1 - Brauser, Stephan A1 - Ullner, Christian A1 - Rethmeier, Michael ED - Grellmann, W. T1 - Bestimmung lokaler Spannungs-Dehnung-Kurven an Widerstandspunktschweißverbindungen von hochfesten Mehrphasenstählen mittels instrumentierter Eindringprüfung N2 - Die lokalen Festigkeiten im Bereich einer Schweißverbindung sind maßgebend für deren Widerstandsfähigkeit gegenüber mechanischen Beanspruchungen. Im Gegensatz zu anderen präparationsaufwendigen Methoden, z. B. die Untersuchung von Mikro-Zugproben, liefert die instrumentierte Eindringprüfung mit deutlich geringerem Aufwand Verläufe von Festigkeiten mit sehr guter Ortsauflösung. Es werden wahre Spannungs-Dehnungs-Kurven aus zyklischen Eindringversuchen mittels Auswertungen auf der Basis repräsentativer Spannungen und Dehnungen und auf der Basis neuronaler Netze an Punktschweißverbindungen zweier hochfester Stähle, eines TRIP-Stahls und eines martensitischen Stahls, sowie eines weichen niedrig legierten Stahls bestimmt, jeweils im Bereich des Grundwerkstoffs und der Schweißlinse. N2 - The local strength properties in the region of weld joints are essential for their resistance to mechanical stress. In contrast to an alternative method of determining the local stress strain behaviour i.e. the preparation intensive, destructive micro tensile test the instrumented indentation test provides gradients of strength properties with excellent local resolution. Two methods of determining true stress strain curves from cyclic indentation test have been used in Order to investigate the strength behaviour in the region of resistance spot welded joints of two high strength steels, a TRIP steel, and a martensitic Steel and on the other hand a mild steel. T2 - DVM-Tagung Werkstoffprüfung 2011 - Neue Entwicklungen in der Werkstoffprüfung - Herausforderungen an die Kennwertermittlung CY - Berlin, Germany DA - 01.12.2011 KW - Lokale Festigkeit KW - Spannungsdehnungskurve KW - Instrumentierte Eindringprüfung KW - Punktschweißverbindung KW - Locally resolved strength KW - Flow curve KW - Instrumented indentation test KW - Spot weld PY - 2011 SN - 978-3-9814516-1-0 SN - 1861-8154 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 643 SP - 343 EP - 348 AN - OPUS4-24978 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlichting, Joachim A1 - Steinfurth, Henrik A1 - Maierhofer, Christiane A1 - Kreutzbruck, Marc T1 - Thermografische Prüfung von Punktschweißverbindungen N2 - Vor allem in der Automobilindustrie wird das Widerstandpunktschweißen im großen Unfang zur Verbindung von Blechen im Karosseriebau verwendet. Durch den anhaltenden Trend zum Leichtbau und den immer höheren Anforderungen an die passive Sicherheit kommt es hier zu einem verstärkten Einsatz innovativer hochfester Stähle. Obwohl es sich beim Punktschweißen um ein lange erprobtes Verfahren handelt, das sich anhand der Prozessparameter und regelmäßiger zerstörender Prüfung überwachen lässt, ist durch diese Entwicklung die Suche nach geeigneten zerstörungsfreien Prüfverfahren wieder aktuell. Wegen der hohen Produktionsgeschwindigkeiten in der automatisierten Fertigung muss sich das Prüfverfahren für eine hundertprozentige Prüfung vollautomatisch mit der typischen Taktrate von etwa einem Hertz durchführen lassen. In dieser Arbeit wird zuerst die prinzipielle Durchführbarkeit der thermografischen Prüfung von Punktschweißverbindungen an speziell präparierten Proben überprüft. Auf dieser Grundlage wird eine Serienuntersuchung an 75 Proben, die sich auf drei Gruppen von Schweißparametern aufteilen und neben optimal geschweißten Proben typische Fehlerbilder repräsentieren, eine Serienuntersuchung gezeigt. Hierzu wird eine Blitzlichtanregung in Transmissionsanordnung verwendet. Es kann gezeigt werden, dass sich mit einer geeigneten Datenaufbereitung die einzelnen Gruppen sicher trennen lassen. Durch eine statistische Bewertung der Ergebnisse kann unter Verwendung eines angepassten Gütekriteriums die Trennschärfe noch deutlich erhöht werden. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Aktive Thermografie KW - Blitzlichtanregung KW - Punktschweißverbindung KW - Transmissionsmessung PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-249915 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Di.1.C.3) SP - 1 EP - 7 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-24991 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Heuskin, D. A1 - Kargl, F. A1 - Griesche, Axel A1 - Stenzel, C. A1 - Mitschke, D. A1 - Bräuer, D. A1 - Meyer, A. T1 - MSL compatible isothermal furnace insert for high temperature shear-cell diffusion experiments N2 - For long-time diffusion experiments shear-cell techniques offer more favourable terms than the traditional long capillary techniques. Here, we present a further developed shear-cell that enables the measurement of diffusion coefficients up to temperatures of 1600 °C. Hence, diffusion experiments can be carried out at temperatures not accessible until now by conventional capillary or shear-cell techniques. The modified shear-cell, which can contain up to six samples of a total length of 90mm and a diameter of 1.5 mm, is built of 30 shear discs of 3mm thickness each. It is operated in an isothermal furnace insert which can be accommodated in the Materials Science Laboratory of the International Space Station. This provides the opportunity that the shear-cell can be applied to microgravity and to ground-based experiments, respectively. The heater insert with an overall length of 518mm and a diameter of 210mm consists of four heating zones with a total power of 3.5 kW. Temperature homogeneity along the graphite sample compartment is better than 2K at 1600°C. Details of the new design are discussed and results of first successfully performed heating and shearing cycles are presented. KW - Microgravity KW - Diffusion KW - Shear cell KW - Melt KW - Alloy PY - 2011 DO - https://doi.org/10.1088/1742-6596/327/1/012053 SN - 1742-6588 SN - 1742-6596 VL - 327 IS - 012053 SP - 1 EP - 8 PB - IOP Publ. CY - Bristol, UK AN - OPUS4-24994 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geier, M. A1 - Eberstein, M. A1 - Grießmann, H. A1 - Partsch, U. A1 - Völkel, L. A1 - Böhme, R. A1 - Mann, Guido A1 - Bonse, Jörn A1 - Krüger, Jörg T1 - Impact of laser treatment on phosphoric acid coated multicrystalline silicon PV-wafers N2 - The selective emitter is a well-known technology for producing highly doped areas under the metallization grid to improve the solar cell performance. In this work, the influence of laser irradiation on phosphoric acid coated multicrystalline silicon PV-wafers on the wafer surface structure, the phosphorous depth distribution and the electrical contact resistance within the laser treated area as well as the electrical series resistance of laserprocessed solar cells was evaluated. Different laser processing settings were tested including pulsed and continuous wave (cw) laser sources (515 nm, 532 nm, 1064 nm wavelength). Complementary numerical simulations using the finite element method (FEM) were conducted to explain the impact of the laser parameters on the melting behavior (melt duration and geometry). It was found that the melt duration is a key parameter for a successful laser Doping process. Our simulations at a laser wavelengths of 515 nm reveal that low-repetition rate (<500 kHz) laser pulses of 300 ns duration generate a melt duration of ~0.35 µs, whereas upon scanning cw-laser radiation at 532 nm prolongates the melt duration by at least one order of magnitude. Experimentally, the widely used ns-laser pulses did not lead to satisfying laser irradiation results. In contrast, cw-laser radiation and scan velocities of less than 2 m/s led to suitable laser doping featuring low electrical resistances in the laser treated areas. T2 - 26th European photovoltaic solar energy conference and exhibition CY - Hamburg, Germany DA - 05.09.2011 KW - Silicon solar cell KW - Selective emitter KW - Laser processing KW - Doping KW - Simulation PY - 2011 SN - 3-936338-27-2 DO - https://doi.org/10.4229/26thEUPVSEC2011-2BV.1.7 SP - 1243 EP - 1247 AN - OPUS4-24995 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberstein, M. A1 - Geier, M. A1 - Grießmann, H. A1 - Partsch, U. A1 - Voelkel, L. A1 - Böhme, R. A1 - Pentzien, Simone A1 - Koter, Robert A1 - Mann, Guido A1 - Bonse, Jörn A1 - Krüger, Jörg T1 - Towards an industrial laser doping process for the selective emitter using phosphoric acid as dopant N2 - Different laser supported approaches have already been realized, proving the great potential of laserdoped selective emitters (LDSE). However, it is challenging to establish a low-cost process by using pulsed laser tools. So far a single-step process only leads to satisfying results utilizing cw-lasers. In this paper we have examined a two-step process to produce laser-doped selective emitters on multicrystalline textured standard silicon photovoltaic wafers (90-Ω/sq-Emitter, SiN-antireflection coating (ARC)). The precise ARC removal by near-infrared fs-laser pulses (30 fs, 800 nm), and the doping of uncoated silicon wafers by ns-laser pulses (8 ns, 532 nm) were systematically investigated. In the fs-experiment, optimum conditions for ARC removal were identified. In the nsexperiments under suitable conditions (melting regime), the phosphorous concentration underneath the wafer surface was significantly increased and the sheet resistance was reduced by nearly a factor of two. Moreover, electrical measurements on fired metallization fingers deposited on the laser processed wafers showed low contact resistances. Hence, wafer conditioning with combined fs-laser- and ns-laser-processes are expected to be a promising technology for producing selective emitters. T2 - 26th European photovoltaic solar energy conference and exhibition CY - Hamburg, Germany DA - 05.09.2011 KW - Laser processing KW - Doping KW - Selective emitter KW - Multicrystalline silicon PY - 2011 SN - 3-936338-27-2 DO - https://doi.org/10.4229/26thEUPVSEC2011-2BV.1.2 SP - 1220 EP - 1223 AN - OPUS4-24996 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, M. A1 - Schultz, C. A1 - Bonse, Jörn A1 - Pahl, H.-U. A1 - Endert, H. A1 - Rau, B. A1 - Schlatmann, R. A1 - Quaschning, V. A1 - Stegemann, B. A1 - Fink, F. T1 - Laser-ablation behavior of thin-film materials used in silicon and CIGSe based solar cells N2 - Structuring of thin-film photovoltaic modules requires basic knowledge of the laser – thin-film interaction in order to adapt the accessible laser parameters, like wavelength, power, repetition rate and scribing speed whilst taking into account the specific material properties of the layer. We have studied the nanosecond laserablation behavior of corresponding layers (i) of silicon based thin-film solar cells with a-Si/µc-Si tandem absorber type and (ii) of back contact and absorber layer of CIGSe solar cells. The respective ablation threshold fluences were determined as integrative parameters describing the specific laser – material interaction. For the threshold determination we used two different methods and developed a new analytical approach taking into account scribing through the glass substrate as it is preferred for most structuring processes. This was done by analyzing the thin film ablation results by means of optical microscopy, profilometry, scanning electron microscopy (SEM). Moreover, we determined the incubation coefficient of the regarded material layers which allows us to predict quantitatively the influence of the spot overlap on the scribing threshold. T2 - 26th European photovoltaic solar energy conference and exhibition CY - Hamburg, Germany DA - 05.09.011 KW - Laser processing KW - Ablation KW - Incubation KW - a-Si/my-Si KW - CIGS PY - 2011 SN - 3-936338-27-2 DO - https://doi.org/10.4229/26thEUPVSEC2011-3DV.2.8 SP - 2943 EP - 2946 AN - OPUS4-24997 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schultz, C. A1 - Schüle, M. A1 - Richter, M. A1 - Pahl, H.-U. A1 - Endert, H. A1 - Bonse, Jörn A1 - Dirnstorfer, I. A1 - Rau, B. A1 - Schlatmann, R. A1 - Quaschning, V. A1 - Fink, F. A1 - Stegemann, B. T1 - P1, P2 and P3 structuring of CIGSe solar cells with a single laser wavelength N2 - Manufacturing of CIGSe thin film solar modules involves typically one laser structuring step (P1) and two mechanical structuring steps (P2 and P3) for serial interconnection. In our approach, complete laser structuring is successfully demonstrated by application of short nanosecond laser pulses (<10 ns) with a single, visible wavelength of 532 nm. The P1 and the P3 trenches are scribed by induced and direct ablation, respectively. For the P2 scribe, the thermal input of the ns laser pulses is used to transform the CIGSe absorber layer locally into a highly conductive compound to provide proper electrical interconnection. These findings promise further simplification and flexibility to thin film solar cell production. T2 - 26th European photovoltaic solar energy conference and exhibition CY - Hamburg, Germany DA - 05.09.2011 KW - Laser processing KW - Nanosecond pulses KW - Ablation KW - Cu(InGa)Se2 KW - Electrical properties PY - 2011 SN - 3-936338-27-2 DO - https://doi.org/10.4229/26thEUPVSEC2011-3AV.1.35 SP - 2540 EP - 2543 AN - OPUS4-24998 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stegemann, B. A1 - Schultz, C. A1 - Schüle, M. A1 - Richter, M. A1 - Pahl, H.-U. A1 - Endert, H. A1 - Bonse, Jörn A1 - Rau, B. A1 - Schlatmann, R. A1 - Quaschning, V. A1 - Fink, F. ED - Luschtinetz, T. ED - Lehmann, J. T1 - Neuartige Laserstrukturierung von CIGSe-Dünnschicht-Solarzellen N2 - Ein wesentlicher Vorteil der Dünnschichtphotovoltaik gegenüber der waferbasierten Photovoltaik liegt in der monolithischen Serienverschaltung. Bei der Herstellung von Chalkopyrit(CIGSe) -Dünnschicht-Solarmodulen erfolgen dafür typischerweise ein Laser-Strukturierungsschritt (P1) und zwei mechanische Strukturierungsschritte (P2, P3). In diesem Beitrag wird gezeigt, dass die Strukturierung von CIGSe-Solarmodulen vollständig mit kurzen Laserpulsen (<10 ns Pulsdauer) und einer einzigen Wellenlänge (532 nm) möglich ist. Der P1- und P3-Schnitt erfolgen durch direkte induzierte Ablation. Für den P2-Schnitt wird gezielt der hohe Wärmeeintrag der ns-Laserpulse genutzt, um die CIGSe- Absorberschicht lokal aufzuschmelzen und strukturell so zu verändern, dass eine elektrisch gut leitende Verbindung zwischen Front- und Rückkontakt entsteht. N2 - A major advantage of thin film photovoltaics over wafer-based photovoltaics is the monolithic series connection. Manufacturing of chalcopyrite (CIGSe) thin film solar modules involves typically one laser structuring step (P1) and two mechanical structuring steps (P2 and P3) for serial interconnection. In our approach, complete laser structuring is successfully demonstrated simply by application of short nanosecond laser pulses (<10 ns) with a single, visible wavelength of 532 nm. The P1 and the P3 trenches are scribed by induced direct ablation. For the P2 scribe, the thermal input of the ns laser pulses is used to transform the CIGSe absorber layer locally into a highly conductive compound to provide proper electrical interconnection between the front and back contact. T2 - 18. Symposium "Nutzung regenerativer Energiequellen und Wasserstofftechnik" / VDI-Tagung "Energieland Mecklenburg-Vorpommern" CY - Stralsund, Germany DA - 03.11.2011 KW - Photovoltaik KW - Dünnschichtsolarzellen KW - Chalkopyrite KW - Laserstrukturierung PY - 2011 SN - 978-3-9813334-4-2 SP - 204 EP - 210 AN - OPUS4-24999 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Häcker, Ralf A1 - Knothe, Esther A1 - Memhard, D. A1 - Andrieux, F. T1 - Containmentsicherheit - Entwicklung und Verifikation von Materialmodellen und numerischen Methoden zur Vorhersage der Containment Sicherheit beim Bersten von Laufrädern in Abgasturboladern (ATL) KW - Containmentsicherheit KW - Hochgeschwindigkeitsprüfung KW - Beschussversuche PY - 2011 IS - 928 - 2011 SP - 1 EP - 214 CY - Frankfurt/M. ET - Abschlussbericht zu Forschungsvorhaben 936 AN - OPUS4-25010 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin A1 - Adam, Christian ED - Rogge, A. ED - Meng, B. T1 - Optimierung von Rückbau und Aufbereitung von Altbeton N2 - Die Qualität von rezyklierten Gesteinskörnungen muss nicht nur bautechnischen Anforderungen und rechtlich verbindlichen Umweltstandards genügen, sondern ihr Einsatz in der Betonherstellung wird auch vor dem Hintergrund der Leitlinien der Nachhaltigkeit bewertet. Für die Gewinnung von rezyklierten Gesteinskörnungen bedeutet dies, dass sowohl bei den Abbrucharbeiten als auch bei der Bauschuttaufbereitung darauf geachtet werden muss, dass die gewählten Verfahren nicht nur ökonomischen Kriterien genügen müssen, sondern auch keine nachteiligen ökologischen oder sozialen Auswirkungen haben dürfen. In verschiedenen Forschungsprojekten konnte durch ökobilanzielle Bewertungen von einzelnen Verfahren und Verfahrensabläufen gezeigt werden, dass rezyklierte Gesteinskörnungen aus Altbeton unter bestimmten Rahmenbedingungen umweltverträglich gewonnen werden können und ihre Nutzung durch die Substitution von Natursteinkörnungen sowohl zur Schonung von natürlichen Ressourcen als auch zu einer Reduzierung von Umweltbelastungen beitragen kann. T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 07.11.2011 KW - Bauschutt KW - Recycling KW - Abbruch KW - Bauschuttaufbereitung KW - Ökobilanzielle Bewertung PY - 2011 SN - 978-3-9814281-0-0 IS - Kap. H3 SP - 308 EP - 317 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-25011 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Schoßig, Jörg A1 - Schmidt, Martin A1 - Krause, U. T1 - Validierung von formalkinetischen Größen aus der adiabatischen Warmlagerung KW - Selbstentzündung KW - Adiabate Warmlagerung KW - Reaktionskinetik PY - 2011 SP - 1 EP - 57 ET - Abschlussbericht Forschungsvorhaben AN - OPUS4-25012 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Fischer, C. A1 - Schmidt, Martin A1 - Meyer, U. A1 - Barth, Uli A1 - Drebenstedt, C. A1 - Wuttke, M. W. T1 - Innovative Technologien für die Erkundung, Löschung und Beobachtung von Kohlebränden - Phase B - N2 - Aufbauend auf den Erkenntnissen der Phase A, die sich auf das grundlegende Verständnis von Kohlebränden, sowie der Voraussetzung und des prinzipiellen Ablaufs der physikalischchemischen Brandprozesse konzentriert haben, erfolgte in Phase B eine Fokussierung auf Methoden zur Vermeidung von Kohlebränden, sowie der Löschung und Überwachung von Kohlebrandzonen, um einen Beitrag zur Verminderung von C02-Emissionen und zum Erhalt der nutzbaren Energieressourcen leisten zu können. Diese Arbeiten erfolgten insbesondere mit Bezug zu den „Clean Development Mechanisms“ (CDM), die im Rahmen des Kyoto-Protokolls entwickelt worden sind. Eine Zertifizierung von Löschaktivitäten im Rahmen des Kyoto-Protokolls setzt dabei eine nachvollziehbare Ermittlung der kohlebrandbezogenen C02-Emissionen und eine belastbare Abschätzung der durch die Löschung verringerten Emissionsmengen voraus. Wesentliche Arbeiten konzentrierten sich auf die Entwicklung von Verfahren, die eine solche Abschätzung gewährleisten können. Dazu wurden unterschiedliche Ansätze entwickelt und anhand der erhobenen Felddaten überprüft. Die untersuchten Ansätze konzentrierten sich dabei auf Verfahren, die eine Ermittlung des vorhandenen Kohlevolumens, die Erfassung der emittierten Gase und die durch die Kohlebrände verursachten Temperaturanomalien an der Tagesoberfläche ermöglichen. Die direkten Arbeiten zum Thema CDM wurden dabei in einem Arbeitspaket unter Federführung der BGR gebündelt. Die deutsche Initiative zur Erforschung der Kohlenbrände in der V.R. China leistete zweifelsfrei signifikante Beiträge zu den oben genannten Zielen. Durch die inventiven Ansätze im Bereich der Brandbewältigung konnte darüber hinaus auch in Teilen die ökonomischen Chancen für ein Engagement deutscher Unternehmen aufgezeigt werden. KW - Kohlebrände KW - Brandbekämpfung KW - Branderkundung PY - 2011 DO - https://doi.org/10.2314/GBV:664529690 SP - 1 EP - 39 AN - OPUS4-25013 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Lehmann, Jens T1 - Korrosionsverhalten nichtrostender Stähle T2 - Seminar Korrosion und Korrosionsschutz CY - Magdeburg, Germany DA - 2011-12-08 PY - 2011 AN - OPUS4-25014 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst A1 - Kruschwitz, Sabine A1 - Martin, Tina T1 - SIP@BAM: Spectral Induced Polarisation used at masonry, wood and concrete T2 - Workshop des Arbeitskreises Induzierte Polarisation CY - Denver, CO, USA DA - 2011-10-31 PY - 2011 AN - OPUS4-25018 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naghib Zadeh, Hamid A1 - Rabe, Torsten A1 - Toepfer, J. A1 - Karmazin, R. T1 - Co-firing of LTCC modules with embedded ferrite layers N2 - Further miniaturization of electronic packaging calls for integration of magnetic functional components into LTCC modules. For integration of magnetic function into LTCC, low fired MnZn- and NiCuZn-ferrites which can be fully densified at the standard LTCC sintering temperature of 900°C were developed. To co-fire these ferrite tapes with dielectric tapes the sintering shrinkage and the coefficient of thermal expansion of ferrite and dielectric tapes must be matched. For each ferrite material a new LTCC dielectric material was designed. The embedded ferrite tapes into new LTCC dielectric tapes can be sufficiently densified during co-firing at 900°C without any cracking. Compared to separately sintered ferrites the permeability of embedded ferrite tapes is reduced. For embedded NiCuZn ferrites permeabilities between 230 and 570 (at 2 MHz) according to the thickness of the embedded ferrite layer were measured. For embedded MnZn ferrites a permeability of 300 was measured. T2 - EMPC-2011 - 18th European microelectronics & packaging conference CY - Brighton, UK DA - 12.09.2011 KW - LTCC KW - Co-firing KW - Ferrite PY - 2011 SN - 978-0-9568086-0-8 IS - TuA2 SP - 1 EP - 6 AN - OPUS4-25021 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen A1 - Kiyak, Yusuf A1 - Wille, Frank A1 - Zerbst, Uwe A1 - Weber, Mike A1 - Klingbeil, Dietmar T1 - Assessment of ductile cast iron fracture mechanics analysis within licensing of German transport packages N2 - In the approval procedure of transport packages for radioactive materials, the mechanical and thermal safety assessment is carried out in Germany by competent authority BAM. In recent years BAM was involved in several licensing procedures of new spent fuel and HLW package designs, where the cask body was made of Ductile Cast Iron (DCI). According to IAEA regulations package designs have to fulfill requirements for specific conditions of transport. Type B(U) packages must withstand the defined accident conditions of transport. The temperature range from -40°C up to the operational temperature has to be considered. For the cask material DCI, it is necessary to determine the brittle fracture behavior. The German guideline BAM-GGR 007 defines requirements for the fracture mechanics of DCI. Due to complex structure of the cask body and the dynamic loading a fracture mechanical assessment in an analytical kind is not always possible. Experience of recent design approval procedures show that the application of numerical calculations are applicable to determine the fracture mechanical load in the cask body. At the first step a numerical analysis has to be done to identify the loading state at the whole cask body. Secondly an analysis of a detail of the cask body is made considering the displacement boundary conditions of the global model. An artificial flaw is considered in this detailed model to calculate the fracture mechanical loading state. The finite element mesh was strongly refined in the area of flaw. The size of the artificial flaw is characterized by the ultrasonic inspection used for the quality assurance of the package. The applicant developed additional analysis tools for calculation of stress intensity factor and/or J-Integral. The assessment approach by BAM led to the decision to develop own tools to the possibility for independent check of the results. The paper describes the authority assessment approach for the DCI fracture mechanics analysis. The validation procedure incl. the development of own tools is explained. BAM developed a post-processor called JINFEM to determine the fracture mechanical loads. The regulatory 1 m puncture bar drop test is used to give an example of the assessment procedure. T2 - 52nd INMM Annual meeting CY - Palm Desert, CA, USA DA - 17.07.2011 KW - Mechanische Bewertung KW - Radioaktives Material KW - Numerische Analyse KW - Bruchmechanik PY - 2011 SP - 1 EP - 10 AN - OPUS4-25022 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gumenyuk, Andrey A1 - Quiroz Penaranda, Vanessa A1 - Rethmeier, Michael T1 - Investigations on Laser Beam Welding o High-Manganese Austentic and Austenitic-Ferritic Stainless Steels T2 - The Fifth International Conference "Laser Technologies in Welding and Materials Processing CY - Crimea, Ukraine DA - 2011-05-24 PY - 2011 AN - OPUS4-25023 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klinger, Christian T1 - Die Bedeutung des 'Materialfehlers' aus der Sicht von Laien, Juristen und Ingenieuren - 'Materialfehler' in Literatur, Regelwerk und Gutachten N2 - Der Begriff „Materialfehler“ wird nicht nur im Bereich der Schadensanalyse von Laien, Juristen und Ingenieuren sondern auch in der Öffentlichkeit sehr häufig verwendet, leider mit den verschiedensten Bedeutungen. Dies führt immer wieder zu Missverständnissen. Ziel der hier vorgestellten BAM-Untersuchung und Recherche war zu klären, ob und ggf. wo es Definitionen für den „Materialfehler“ gibt, wie der Begriff in den oben angesprochenen Bereichen verwendet wird. Weiterhin wurde untersucht, ob diese Verwendungen / Definitionen in die in der Schadensanalyse definierte Begriffswelt passen bzw. welche Definition ergänzt werden sollte. Im Gegensatz zu „Material“, „Werkstoff1 oder „Werkstofffehler“ ist der häufig verwendete Begriff „Materialfehler“ erstaunlicherweise bisher nicht definiert! Um den oft verwendeten Begriff des Materialfehlers für die Schadensanalyse und die damit befassten Bereiche einheitlich zu beschreiben, wird folgende Definition vorgeschlagen: „Materialfehler" sind Werkstoff- und/oder Fertigungsfehler. Darin sind alle Fehler (Abweichungen von Spezifikationen/Normen) im Werkstoff bzw. dessen Herstellung/Fertigung enthalten. Demgegenüber sind Konstruktions-/Planungsfehler oder Betriebsfehler keine Materialfehler. T2 - 37. VDI-Jahrestagung - Schadensanalyse - Produktverbesserung durch Schadensanalyse CY - Würzburg, Germany DA - 19.10.2011 KW - Schadensanalyse PY - 2011 SN - 978-3-18-092150-1 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte VL - 2150 SP - 113 EP - 120 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-25024 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gumenyuk, Andrey A1 - Quiroz Penaranda, Vanessa A1 - Rethmeier, Michael T1 - Investigation of the hot cracking susceptibility of laser welds with the CTW (Controlled Tensile Weldability)-test T2 - 64th IIW Annual Assembly CY - Chennai, India DA - 2011-07-17 PY - 2011 AN - OPUS4-25025 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gaul, Holger A1 - Brauser, Stephan A1 - Weber, Gert A1 - Rethmeier, Michael T1 - Methods to obtain weld discontinuities in spot-welded joints made of advanced high-strength steels N2 - Resistance spot welding is the major joining technique in mass car production. This applies in particular to high-strength steel and advanced high-strength steel (AHSS) joining of thin sheet steel components for lightweight body shell structures. Joining of AHSS in mass production might lead to weld discontinuities under certain circumstances. Those discontinuities in form of cracks might be an initial start of cracking in the spot-welded joints regarding fatigue loads. It is of great interest to figure out, if, in comparison to specimens without weld discontinuities, the crack initiating point changes and if the fatigue resistance might be reduced by the discontinuities. In this contribution, an overview of potential discontinuities is given. Their possible causes are discussed and means for their detection are highlighted. Among the possible causes of weld discontinuities, two major groups are distinguished: the welding parameters as primary influences in the welding process, and the production-specific influences as secondary ones. With emphasis on major cracks penetrating the weld nugget, these influences are analysed. Finally, a combination of extreme welding parameters with production-specific influences is chosen in order to establish a method which enables the preparation of fatigue test specimens with reproducible major cracks in different locations of the spot-welded joints. This method is than applied in order to prepare spot weld specimens for fatigue tests. KW - Cracking KW - Defects KW - Fatigue loading KW - High strength steels KW - Resistance spot welding PY - 2011 SN - 0043-2288 SN - 1878-6669 VL - 55 IS - 11/12 SP - 99 EP - 106 PB - Springer CY - Oxford AN - OPUS4-25026 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quiroz Penaranda, Vanessa A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Comparison between CO2- and Nd: YAG-laser beam welding of high strength CrMnNi-steels for the automotive industry T2 - 64th IIW-Annual Assemby CY - Chennai, India DA - 2011-07-17 PY - 2011 AN - OPUS4-25027 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - Material properties for welding simulation - measurement, analysis, and exemplary data N2 - Welding is a key technology in the area of industrial production due to its flexibility and efficiency. However, new materials and welding techniques necessitate permanent research activities in order to keep up with the demands. A detailed knowledge about the process itself and the heat effects of welding, e.g., temperatures, distortions, and stresses, is the basis for a target-oriented optimization instead of a trial-and-error approach. Numerical welding simulation is a powerful tool to meet these demands. Complementary to an experimental investigation, it enables the analysis of the specimen during the welding process, commonly known as computational welding mechanics (CWM). Whereas simulation is nowadays a common tool in different development processes, the modeling of welding still remains difficult because of the multiple physical effects taking place. One of the most important problems for the user is the lack of knowledge about the material properties as input data for the simulation. Furthermore, any scattering of the data causes uncertainties that can have major effects on the calculations. The objective of this paper is to give an overview about the experimental determination and analysis of the material properties needed as input data for a welding simulation. The measurement techniques and the occurring deviations of the results are discussed. Additionally, the collected data for three representative alloys (dual-phase steel, austenitic steel, precipitation-hardenable aluminum alloy) are analyzed. Finally, the temperature-dependent thermophysical and thermomechanical material properties for these three alloys are given in a ready-to-use format for a numerical welding simulation. KW - Thermophysical material properties KW - Thermomechanical material properties KW - Experimental determination KW - Numerical welding simulation PY - 2011 SN - 0043-2296 SN - 0096-7629 VL - 90 SP - 220-s EP - 227-s PB - American Welding Society CY - New York, NY AN - OPUS4-25028 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Perret, William A1 - Thater, Raphael A1 - Alber, U. A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - Case study for welding simulation in the automotive industry N2 - Welding is one of the most widely used joining processes in structural applications, like in car body production in the automotive industry. It is well-known that distortions and residual stresses occur during and after the welding process. Many procedures exist to decrease these negative heat effects of welding, but are often coupled with highly cost intensive experiments. For several decades, simulation models have been developed to understand and predict the heat effects of welding and to reduce experimental effort. In the production planning of various Original Equipment Manufacturers (OEM), some simulation tools are already well established, e.g. for crash test, forming or casting simulations. For welding, the demand is high but the implementation of welding simulation software is still not established yet. Welding is a complex process and the development of a flexible simulation tool, which produces good simulation results without expert knowledge in simulation, is not an easy task. In this paper, a welded assembly from the automotive industry has been simulated and compared to experimental data. Temperature fields and transient distortion distributions have been measured with thermocouples and with an optical 3D deformations analysis tool, respectively. The simulation has been run with a commercially available welding simulation software. The simulated temperature fields match the numerical ones perfectly. The simulated distortions are also qualitatively in best agreement with the experimental ones. Quantitatively, a difference of approximately 20 % between the simulated and the measured distortions is visible; this is acceptable considering the simplifications and assumptions of the simulation model. The global time to solution to get these results without expert knowledge in welding simulation was between 4 and 6 weeks, which is a reasonable time frame for an industrial application of welding simulation. KW - Automobiles KW - Distortion KW - Simulating KW - Temperature KW - Welding KW - Aluminium alloys KW - Al Mg Si alloys KW - Automobile engineering KW - Finite elements analysis KW - Mathematical models KW - MIG welding KW - Residual stresses KW - Vehicle bodies PY - 2011 DO - https://doi.org/10.1007/BF03321546 SN - 0043-2288 SN - 1878-6669 VL - 55 IS - 11/12 SP - 89 EP - 98 PB - Springer CY - Oxford AN - OPUS4-25029 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gründer, Klaus-Peter A1 - Köppe, Enrico A1 - Kadoke, Daniel T1 - Optische 3D-Referenzierung eines funkgestützten Multisensorsystems zur Bewegungsanalyse gefährdeter Personen T2 - 14. Anwendungsbezogener Workshop zur Erfassung, Modellierung, Verarbeitung und Auswertung von 3D-Daten - 3D-NordOst 2011 CY - 08.12.2011 DA - 2011-12-08 PY - 2011 AN - OPUS4-25000 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Suhm, M.A. A1 - Buurman, Merwe T1 - Comment on 'theoretical investigations into the enantiomeric and racemic forms of alpha-(trifluoromethyl)lactic acid' by R. Tonner, V.A. Soloshonok and P. Schwerdtfeger, Phys. Chem. Chem. Phys., 2011, 13, 811-817 N2 - It is argued that differences between homo- and heterochiral dimers of the title compound in the gas phase cannot be responsible for the different sublimation behaviour of racemic and enantiomerically pure crystals near room temperature. KW - Chirality recognition KW - Sublimation PY - 2011 DO - https://doi.org/10.1039/c0cp02455d SN - 1463-9076 SN - 1463-9084 N1 - Geburtsname von Buurman, Merwe: Albrecht, M. - Birth name of Buurman, Merwe: Albrecht, M. VL - 13 IS - 9 SP - 4159 EP - 4160 PB - The Royal Soc. of Chemistry CY - Cambridge AN - OPUS4-25001 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Arlt, Tobias A1 - Grothausmann, R. A1 - Manke, I. A1 - Markötter, H. A1 - Krüger, P. A1 - Haussmann, J. A1 - Hilger, A. A1 - Kardjilov, N. A1 - Hartnig, C. A1 - Kupsch, Andreas A1 - Lange, Axel A1 - Hentschel, Manfred P. A1 - Wippermann, K. A1 - Banhart, J. T1 - Tomografische Methoden für die Brennstoffzellenforschung N2 - Auf Grund des hohen Wirkungsgrades und der vielfältigen Einsatzmöglichkeiten stellen Brennstoffzellen sowie Brennstoffzellenverbünde eine vielversprechende Energiequelle dar. Daher ist es wichtig, die Prozesse während des Betriebs einer Brennstoffzelle exakt charakterisieren zu können, um diese im nächsten Schritt zu optimieren. So ist ein ausbalanciertes Wassermanagement in einer mit Wasserstoff betriebenen Zelle ausschlaggebend für ihre Leistungsfähigkeit. Für eine dauerhafte Leistungsfähigkeit muss das entstehende Wasser die Membran feucht halten, um so die Protonenleitfähigkeit aufrecht zu erhalten. Zu viel Wasser kann jedoch die Gaszufuhr durch die porösen Materialien in Richtung Membran verhindern. Alterungsphänomene der einzelnen Komponenten können dieses sensible Wassermanagement stören und so die Leistungsfähigkeit einer Brennstoffzelle herabsetzen. Zum tieferen Verständnis der Wasserverteilung werden zerstörungsfreie Methoden, wie zum Beispiel die ex situ Neutronentomografie oder die in situ Synchrotronradiografie eingesetzt. Letztere Methode kann während des Brennstoffzellenbetriebs in Kombination mit weiteren Messmethoden, wie der ortsaufgelösten Stromdichtemessung, eingesetzt werden. So können einzelne Brennstoffzellenkomponenten, wie die Gasdiffusionsschichten, charakterisiert werden. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Computer-Tomographie KW - Rekonstruktionsalgorithmen KW - Röntgen-Kanten-Tomographie KW - Neutronen-Tomographie KW - Elektronen-Tomographie PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-250023 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (P7) SP - 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25002 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lange, Axel A1 - Müller, Bernd R. A1 - Hentschel, Manfred P. A1 - Kupsch, Andreas T1 - Korrektur des Hinterleuchtens an CT-Synchrotrondaten N2 - In den unterschiedlichsten Methoden der Computertomographie tritt häufig ein diffuses Untergrundsignal in den Einzelprojektionen auf: im Falle der Parallelstrahl-CT mit Synchrotronstrahlung handelt es sich um ein Hinterleuchten durch den Fluoreszenzschirm, der vor der CCD-Kamera angeordnet ist. Dieses Hinterleuchten unterscheidet sich von dem bekannten Nachleuchten (Phosphoreszenz) durch zeitliche Konstanz. Hier äußert sich das Hinterleuchten als Modulation der projizierten Masse und somit als Funktion der Phase (Projektionswinkel) und des Aspektverhältnisses des Objektes. Der Einfluss des Hinterleuchtens ist abhängig von der Größe des von der Probe abgeschatteten Detektorbereiches und des Objektumfangs (Dynamik). Dies hat u.a. zur Folge, dass Abweichungen vom Absorptionsgesetz auftreten, die umso stärker ausgeprägt sind, je weniger Detektorfläche das Objekt abdeckt und je stärker das Objekt schwächt. Dabei können Aufhärtungseffekte wegen der monochromatischen Strahlung ausgeschlossen werden. Mit Referenzmessungen und einem isotropen, homogenen Ansatz, der diese Abweichung als Hinterleuchten beschreibt, lassen sich die auftretenden Fehler deutlich verringern. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Hinterleuchten KW - Detektor KW - Fluoreszenzschirm KW - Synchrotron-Radiographie KW - Computer-Tomographie PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-250038 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (P6) SP - 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25003 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kupsch, Andreas A1 - Lange, Axel A1 - Hentschel, Manfred P. A1 - Grothausmann, R. A1 - Manke, I. T1 - Verbesserte Elektronen-Tomographie mittels DIRECTT-Algorithmus N2 - Tomographische Messungen in Transmissions-Elektronenmikroskopen beziehen ihren Reiz aus der hohen Ortsauflösung im Nanometerbereich. Allerdings bringen sie neben dem hohen Aufwand bei der Probenpräparation auch eine außerordentliche Häufung von Restriktionen der Messung mit sich, die bei Verwendung herkömmlicher Rekonstruktionsalgorithmen zu erheblichen Artefakten führen. Diese Restriktionen betreffen: partielle Nichtdurchstrahlbarkeit, einen eingeschränkten Winkelbereich, wenige Projektionen in Bezug auf die Detektorgröße, Probenabbildungen größer als der Detektor, instabile Rotationsachse, variierende Winkelinkremente sowie Probenveränderungen während der Messung. Der DIRECTT-Algorithmus (Direkte iterative Rekonstruktion computertomographischer Trajektorien) kann, abgesehen von der Probenveränderung, sämtliche dieser Restriktionen geeignet berücksichtigen. Die auftretenden, teils unvollständigen Bahnen lassen sich mittels einer Treffertabelle und geeigneter Auswahl iterativ behandeln. Außerdem kann das Rekonstruktionsvolumen über die Detektorlänge hinaus erweitert werden. Damit gelingt eine weitgehende Unterdrückung von Rekonstruktionsartefakten, insbesondere der sonst dominanten Streifenartefakte, und eine deutliche Erhöhung der Ortsauflösung. Die Verbesserung der Rekonstruktionsqualität wird anhand von Modell- und experimentellen Daten gezeigt. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Elektronen-Tomographie KW - Computer-Tomographie KW - Rekonstruktionsalgorithmen PY - 2011 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (P8) SP - 1 EP - 7 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25004 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Aegerter, J. A1 - Kühn, Hans-Joachim A1 - Frenz, H. A1 - Weißmüller, C. T1 - EN ISO 6892-1:2009 - Tensile testing: initial experience from the practical implementation of the new standard N2 - With the publication of EN ISO 6892-1:2009, the harmonisation of tensile testing at room temperature in Europe was achieved by combining EN 10002-1:2001 with ISO 6892:1998. Essential changes are the introduction of the strain rate and the strain rate control as the significant testing rate or control mode, respectively, referred to as “Method A”. By using this method in the correct way it is guaranteed that in the moment of determination of properties comparable resulting strain rates at the test piece in smaller ranges of specified strain rates are adopted — also if different stiffnesses of the testing equipment are present. This leads especially for strain rate sensitive materials to better comparable results. In this paper it is documented the need for the implementation of method A, methods for the realisation — also by the use of older testing systems — and an example of the comparability of results of the methods for a strain-rate-sensitive-steel. KW - Zugversuch KW - Dehngeschwindigkeit KW - Steifigkeit PY - 2011 SN - 0025-5300 VL - 53 IS - 10 SP - 595 EP - 603 PB - Hanser CY - München AN - OPUS4-25005 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Aegerter, J. A1 - Kühn, Hans-Joachim A1 - Frenz, H. A1 - Weißmüller, C. T1 - DIN EN ISO 6892-1:2009 - Der Zugversuch - Erste Erfahrungen aus der praktischen Umsetzung der neuen Norm N2 - Mit der Veröffentlichung der DIN EN ISO 6892-1:2009 wurde für den Zugversuch bei Raumtemperatur eine Harmonisierung der in Europa verbindlichen EN 10002-1:2001 mit der ISO 6892:1998 erreicht. Wesentliche Änderungen sind die Einführung der Dehngeschwindigkeit und der Dehngeschwindigkeitsregelung als maßgebliche Prüfgeschwindigkeit bzw. Regelungsart, als Verfahren A bezeichnet. Mit der korrekten Anwendung dieses Verfahrens wird gewährleistet, dass im Moment der Kennwerteermittlung bei enger spezifizierten zulässigen Dehngeschwindigkeitsbereichen vergleichbare resultierende Dehngeschwindigkeiten an der Probe auch bei unterschiedlichen Steifigkeiten der Prüfaufbauten vorliegen. Dieses führt besonders bei dehngeschwindigkeitssensitiven Werkstoffen zu deutlich vergleichbareren Ergebnissen. In diesem Beitrag wird auf die Notwendigkeit der Einführung des Verfahrens A, der möglichen Umsetzungen auch bei Verwendung von älteren Prüfsystemen sowie exemplarisch auf vergleichende Ergebnisse der Verfahren an einem dehngeschwindigkeitssensitivem Stahlwerkstoff eingegangen. KW - Zugversuch KW - Dehngeschwindigkeit KW - Steifigkeit PY - 2011 SN - 0025-5300 VL - 53 IS - 10 SP - 586 EP - 594 PB - Hanser CY - München AN - OPUS4-25006 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bloching, H. A1 - Aegerter, J. A1 - Kühn, Hans-Joachim ED - Grellmann, W. T1 - DIN EN ISO 6892-2: Wesentliche Änderungen in der Norm zum Warmzugversuch N2 - Die im Mai 2011 veröffentlichte Internationale Norm ISO 6892-2 "Metallische Werkstoffe — Zugversuch - Teil 2: Prüfverfahren bei erhöhter Temperatur" ersetzt die Europäische Norm EN 10002-5 und die Internationale Norm ISO 783. Technische Änderungen/Ergänzungen im Vergleich zu den Vorgängernormen beziehen sich im Wesentlichen auf die Prüfgeschwindigkeiten und die Dehnungsmessung. In Anlehnung an Teil 1 der ISO 6892 (Prüfung bei Raumtemperatur) wird die Dehngeschwindigkeit als maßgebliche Prüfgeschwindigkeit mit eingeengten Bereichen (Verfahren A) empfohlen. Zum Ansetzen des Dehnungsaufnehmers und zur Festlegung der Messlänge sind nun verschiedene Verfahren möglich. In dem Beitrag wird auch anhand von Beispielen auf mögliche Auswirkungen auf die zu bestimmenden Kennwerte eingegangen. T2 - DVM-Tagung Werkstoffprüfung 2011 - Neue Entwicklungen in der Werkstoffprüfung - Herausforderungen an die Kennwertermittlung CY - Berlin, Germany DA - 01.12.2011 KW - Warmzugversuch KW - Thermische Ausdehnung KW - Messlänge KW - Dehngeschwindigkeit PY - 2011 SN - 978-3-9814516-1-0 SN - 1861-8154 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 643 SP - 245 EP - 252 AN - OPUS4-25007 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen A1 - Wille, Frank A1 - Weber, Mike A1 - Kiyak, Yusuf A1 - Zerbst, Uwe A1 - Klingbeil, Dietmar T1 - Assessment of Ductile Cast Iron Fracture Mechanics Analysis within Licensing of German Transport Packages T2 - INMM, 52nd Annual Meeting CY - Palm Desert, CA, USA DA - 2011-07-17 PY - 2011 AN - OPUS4-25008 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hahn, Oliver ED - Ketelsen, T. ED - Hahn, Oliver ED - Kuhlmann-Hodick, P. T1 - Zeichnen - Die niederländischen Zeichnungen des 16. Jahrhunderts im Dresdner Kupferstich-Kabinett - Beiträge zu einer Typologie im Zeitalter Bruegels KW - ZfP KW - Archäometrie KW - Kunstgeschichte KW - Kulturgeschichte PY - 2011 SN - 978-3-86335-084-0 SP - 1 EP - 416 PB - Verlag der Buchhandlung Walther König CY - Köln AN - OPUS4-25009 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quiroz Penaranda, Vanessa A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Comparison between CO2- and Nd: YAG-Laser beam welding of high strength CrMnNi-steels for the automotive industry T2 - Select Committe "Automotive and Road transport" Intermediate Meeting CY - IJmuiden, Netherlands DA - 2011-04-11 PY - 2011 AN - OPUS4-25030 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quiroz Penaranda, Vanessa A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Properties of laser welded H400 austenitic chrome-manganese stainless steel sheets T2 - 3rd International Conference Steels in Cars and Trucks CY - Salzburg, Austria DA - 2011-06-05 PY - 2011 AN - OPUS4-25031 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Rohrschweißen mit Hochleistungsfestkörperlasern T2 - DVS-Congress CY - Hamburg, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-25032 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mente, Tobias A1 - Marcano, Diana A1 - Kannengießer, Thomas T1 - Schweißeignung höherfester Feinkornbaustähle mit Streckgrenzen über 1000 MPa T2 - Konzerforschungsseminar - voestalpine "welding of high strength steels" CY - Linz, Austria DA - 2011-03-24 PY - 2011 AN - OPUS4-25033 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mente, Tobias A1 - Kannengießer, Thomas T1 - Numerische Simulation wasserstoffunterstützter Kaltrisse in hochfesten Stählen T2 - Konzernforschungsseminar - voestapline "welding of high strength steels" CY - Linz, Austria DA - 2011-03-24 PY - 2011 AN - OPUS4-25034 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mente, Tobias A1 - Böllinghaus, Thomas T1 - Mesoscale modelling of hydrogen diffusion in duplex stainless steels T2 - IIW Annual Assembly CY - Chennai, India DA - 2011-07-17 PY - 2011 AN - OPUS4-25035 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Heinze, Christoph A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - Numerical calculation of residual stress development of multi-pass gas metal arc welding under high restraint conditions N2 - During welding, residual stresses build-up created by the steep thermal gradient that occurs in the weld zone from localized heating and cooling, and phase transformations appearing in low-alloyed structural steel is inevitable. Welding of rather simple test plates do not cover the actual structural effects, which have to be considered during real component welding. However, the resulting welding-induced residual stress state is highly influenced by the structural characteristics, i.e. restraint conditions, of the welded construction. Therefore, a unique large-scale testing facility providing a specific shrinkage restraint while welding and subsequent cooling was used for the present investigations. Hereby, a six bead multi-pass gas metal arc weld of 20 mm thick structural steel S355J2 + N was welded under shrinkage restraint. The residual stresses were experimentally and numerically investigated, and compared to an analysis of plates welded under force-free support and free shrinkage conditions. The experimentally determined and calculated residual stresses using both 2D and 3D numerical models are in a good agreement. Furthermore, the influence of a shrinkage restraint on the residual stress distribution is both experimentally and numerically shown for the present test set-up. KW - Welding KW - Shrinkage KW - Ferrous metals and alloys PY - 2011 DO - https://doi.org/10.1016/j.matdes.2011.09.021 SN - 0261-3069 SN - 0264-1275 VL - 35 SP - 201 EP - 209 PB - Elsevier Science CY - Oxford AN - OPUS4-25036 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bennetts, V.H. A1 - Lilienthal, A.J. A1 - Neumann, Patrick P. A1 - Trincavelli, M. T1 - Mobile robots for localizing gas emission sources on landfill sites: is bio-inspiration the way to go? N2 - Roboticists often take inspiration from animals for designing sensors, actuators or algorithms that control the behaviour of robots. Bio-inspiration is motivated with the uncanny ability of animals to solve complex tasks like recognizing and manipulating objects, walking on uneven terrains, or navigating to the source of an odour plume. In particular the task of tracking an odour plume up to its source has nearly exclusively been addressed using biologically inspired algorithms and robots have been developed, for example, to mimic the behaviour of moths, dungbeetles, or lobsters. In this paper we argue that biomimetic approaches to gas source localization are of limited use, primarily because animals differ fundamentally in their sensing and actuation capabilities from state-of-the-art gas-sensitive mobile robots. To support our claim, we compare actuation and chemical sensing available to mobile robots to the corresponding capabilities of moths. We further characterize airflow and chemosensor measurements obtained with three different robot platforms (two wheeled robots and one flying micro drone) in four prototypical environments and show that the assumption of a constant and unidirectional airflow, which is at the basis of many gas source localization approaches, is usually far from being valid. This analysis should help to identify how underlying principles, which govern the gas source tracking behaviour of animals, can be usefully 'translated' into gas source localization approaches that fully take into account the capabilities of mobile robots. We also describe the requirements for a reference application, monitoring of gas emissions at landfill sites with mobile robots, and discuss an engineered gas source localization approach based on statistics as an alternative to biologically-inspired algorithms. KW - Mobile robotics KW - Mobile robot olfaction KW - Biologically inspired robots KW - Landfill surveillance PY - 2011 UR - http://journal.frontiersin.org/Journal/10.3389/fneng.2011.00020/full DO - https://doi.org/10.3389/fneng.2011.00020 SN - 1662-6443 SP - 1 EP - 14 PB - Frontiers Research Foundation CY - Lausanne AN - OPUS4-25037 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miccoli, Lorenzo A1 - Perrone, Chiara A1 - Müller, Urs A1 - Gardei, André A1 - Ziegert, C. T1 - Structural performances of earthen building materials. A comparison between different typologies T2 - 2nd WTA - International PhD Symposium CY - Brno, Czech Republic DA - 2011-10-06 PY - 2011 AN - OPUS4-25038 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miccoli, Lorenzo A1 - Perrone, Chiara A1 - Müller, Urs A1 - Gardei, André A1 - Ziegert, C. T1 - Comparison of mechanical behavior of different earth masonry typologies in cultural heritage T2 - WCCE-ECCE-TCCE Joint Conference 2 - Seismic protection of cultural heritage CY - Antalya, Turkey DA - 2011-10-31 PY - 2011 AN - OPUS4-25039 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bremser, Wolfram T1 - Verifizierung statistischer Modelle mittels Monte-Carlo-Simulation T2 - 5. VDI-Fachtagung "Messunsicherheit praxisgerecht bestimmen" CY - Erfurt, Germany DA - 2011-11-08 PY - 2011 AN - OPUS4-24982 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Darlatt, Erik A1 - Traulsen, C. H.-H. A1 - Poppenberg, J. A1 - Richter, S. A1 - Schalley, C. A. A1 - Unger, Wolfgang T1 - The Coordination of Palladium(II)-ions changes the preferential orientation of pyridyl terminated self-assembled monolayer molecules - A NEXAFS study T2 - Joint BER II and BESSY II User Meeting 2011 CY - Berlin, Germany DA - 2011-12-01 PY - 2011 AN - OPUS4-24984 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gnutzmann, Tanja A1 - Klimakow, Maria A1 - Rademann, Klaus A1 - Emmerling, Franziska T1 - Combined in situ synchrotron X-ray diffraction and Raman spetroscopy for the study of crystallization processes T2 - PRORA 2011 - Fachtagung Prozessnahe Röntgenanalytik CY - Berlin, Germany DA - 2011-11-24 PY - 2011 AN - OPUS4-24985 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Reich, Franziska A1 - Schurig, Michael A1 - Jochems, Frank T1 - Ventilierendes Ansprechverhalten - Sicherheitsventile - Die Vor- und Nachteile des Einsatzes von Druckentlastungseinrichtungen im Tankbetrieb unter Praxisbedingungen waren Thema eines Forschungsprojekts der BAM. N2 - Ortsbewegliche Tanks oder Tankcontainer müssen in der Praxis gegen das Erreichen eines unzulässigen Betriebsdruckes abgesichert sein. Hierbei werden dem Betreiber Möglichkeiten hinsichtlich technischer und organisatorischer Maßnahmen angeboten. Eine davon bietet die Absicherung der Gefahrgutumschließung durch Druckentlastungseinrichtungen. Die Bedingungen hierfür werden in den verkehrsträgerspezifischen Vorschriften geregelt. So regeln beispielsweise die Anhänge des RID/ADR die Bedingungen für den Transport auf Straße und Schiene. PY - 2011 SN - 0016-5808 VL - 56 IS - 11 SP - 17 EP - 19 PB - Storck CY - Hamburg AN - OPUS4-24986 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Napp, J. A1 - Behnke, Thomas A1 - Fischer, L. A1 - Würth, Christian A1 - Wottawa, M. A1 - Katschinski, D.M. A1 - Alves, F. A1 - Resch-Genger, Ute A1 - Schäferling, M. T1 - Targeted luminescent near-infrared polymer-nanoprobes for in vivo imaging of tumor hypoxia N2 - Polystyrene nanoparticles (PS-NPs) were doped with an oxygen-sensitive near-infrared (NIR)-emissive palladium meso-tetraphenylporphyrin and an inert reference dye which are both excitable at 635 nm. The nanosensors were characterized with special emphasis on fundamental parameters such as absolute photoluminescence quantum yield and fluorescence lifetime. The PS-NPs were employed for ratiometric dual-wavelength and lifetime-based photoluminescent oxygen sensing. They were efficiently taken up by cultured murine alveolar macrophages, yielding a characteristic and reversible change in ratiometric response with decreasing oxygen concentration. This correlated with the cellular hypoxic status verified by analysis of hypoxia inducible factor-1α (HIF-1α) accumulation. In addition, the surface of PS-NPs was functionalized with polyethylene glycol (PEG) and the monoclonal antibody herceptin, and their binding to HER2/neu-overexpressing tumor cells was confirmed in vitro. First experiments with tumor-bearing mouse revealed a distinctive ratiometric response within the tumor upon hypoxic condition induced by animal sacrifice. These results demonstrate the potential of these referenced NIR nanosensors for in vitro and in vivo imaging that present a new generation of optical probes for oncology. KW - Fluorescence KW - NIR KW - Nanoparticles KW - Microparticles KW - Imaging KW - Cancer KW - Oxygene PY - 2011 DO - https://doi.org/10.1021/ac201870b SN - 0003-2700 SN - 1520-6882 VL - 83 IS - 23 SP - 9039 EP - 9046 PB - American Chemical Society CY - Washington, DC AN - OPUS4-24987 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar A1 - Sarfraz, Adnan A1 - Klimakow, Maria A1 - Gnutzmann, Tanja A1 - Polte, Jörg A1 - Delißen, Friedmar A1 - Batzdorf, Lisa A1 - Emmerling, Franziska T1 - In-situ investigations utilizing levitated droplets T2 - Bessy User Meeting 2011 CY - Berlin, Germany DA - 2011-11-29 PY - 2011 N1 - Geburtsname von Batzdorf, Lisa: Tröbs, L. - Birth name of Batzdorf, Lisa: Tröbs, L. AN - OPUS4-24988 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit T1 - Use of Higher -alloyed metallic materials and duplex steels for transport tanks of dangerous goods T2 - Stainless Steel World 2011 CY - Maastricht, Netherlands DA - 2011-11-29 PY - 2011 AN - OPUS4-25040 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pötzsch, Klaus-Michael A1 - Würsig, Andreas T1 - Was ist der richtige Tank T2 - IHK Gefahrguttag Sachsen-Anhalt CY - Leuna, Germany DA - 2011-11-24 PY - 2011 AN - OPUS4-25041 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mangelsdorf, Axel T1 - Normung und Standardisierung als Erfolgsfaktor im internationalen Handel: Fallbeispiel LED T2 - Sitzung BMWi-ZVEI- Projektgruppe CY - Berlin, Germany DA - 2011-05-02 PY - 2011 AN - OPUS4-25042 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Flammability of solids T2 - ECHA Trainig Course "Physical and Chemical Properties" CY - Berlin, Germany DA - 2011-10-24 PY - 2011 AN - OPUS4-25043 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - Oxidizing properties for solids and liquids T2 - ECHA Trainig Course "Physical and Chemical Properties" CY - Berlin, Germany DA - 2011-10-24 PY - 2011 AN - OPUS4-25044 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin A1 - Lüth, Peter T1 - Interlaboraty test 2010/11 "EN 15188:2007 - Self-Ignition temperature" - Präsentation der Zwischenergebnisse Oktober 2011 - T2 - ProcessNet-Arbeitsausschuss "Sicherheitstechnische Kenngrößen" CY - Frankfurt am Main, Germany DA - 2011-10-26 PY - 2011 AN - OPUS4-25045 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schalau, Bernd A1 - Habib, Abdel Karim A1 - Schmidt, Dirk T1 - Modellierung einer Lachenverdunstung nach störfallbedingten Freisetzungen T2 - Meinungs- und Erfahrungsaustausch für Sachverständige nach § 29a BImSchG CY - Dresden, Germany DA - 2011-12-15 PY - 2011 AN - OPUS4-25046 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schalau, Bernd A1 - Habib, Abdel Karim A1 - Schmidt, Dirk T1 - Modellierung einer Lachenverdunstung nach störfallbedingten Freisetzungen T2 - Meinungs- und Erfahrungsaustausch für Sachverständige nach § 29a BImSchG CY - Augsburg, Germany DA - 2011-12-01 PY - 2011 AN - OPUS4-25047 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Marinelli, F. A1 - Kuhlmann, S.I. A1 - Grell, E. A1 - Kunte, Hans-Jörg A1 - Ziegler, C. M. A1 - Faraldo-Gómez, J.D. T1 - Evidence for an allosteric mechanism of substrate release from membrane-transporter accessory binding proteins N2 - Numerous membrane importers rely on accessory water-soluble proteins to capture their substrates. These substrate-binding proteins (SBP) have a strong affinity for their ligands; yet, substrate release onto the low-affinity membrane transporter must occur for uptake to proceed. It is generally accepted that release is facilitated by the association of SBP and transporter, upon which the SBP adopts a conformation similar to the unliganded state, whose affinity is sufficiently reduced. Despite the appeal of this mechanism, however, direct supporting evidence is lacking. Here, we use experimental and theoretical methods to demonstrate that an allosteric mechanism of enhanced substrate release is indeed plausible. First, we report the atomic-resolution structure of apo TeaA, the SBP of the Na+-coupled ectoine TRAP transporter TeaBC from Halomonas elongata DSM2581T, and compare it with the substrate-bound structure previously reported. Conformational free-energy landscape calculations based upon molecular dynamics simulations are then used to dissect the mechanism that couples ectoine binding to structural change in TeaA. These insights allow us to design a triple mutation that biases TeaA toward apo-like conformations without directly perturbing the binding cleft, thus mimicking the influence of the membrane transporter. Calorimetric measurements demonstrate that the ectoine affinity of the conformationally biased triple mutant is 100-fold weaker than that of the wild type. By contrast, a control mutant predicted to be conformationally unbiased displays wild-type affinity. This work thus demonstrates that substrate release from SBPs onto their membrane transporters can be facilitated by the latter through a mechanism of allosteric modulation of the former. KW - Binding thermodynamics KW - Periplasmic binding protein KW - Secondary transporter KW - ABC transporter KW - Replica-exchange metadynamics PY - 2011 DO - https://doi.org/10.1073/pnas.1112534108 SN - 0027-8424 SN - 1091-6490 VL - 108 IS - 49 SP - E1285 EP - E1292 PB - National Academy of Sciences CY - Washington, DC AN - OPUS4-25049 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schilder, Constanze A1 - Kusche, Nadine A1 - Schukar, Vivien A1 - Habel, Wolfgang T1 - Development and qualification of FBG-based strain patches and rosettes T2 - 8th International Workshop on Structural Health Monitoring - 2011 CY - Stanford, CA, USA DA - 2011-09-13 PY - 2011 AN - OPUS4-27472 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bettge, Dirk A1 - Kranzmann, Axel A1 - Ruhl, Aki Sebastian T1 - COORAL Teilprojekt MINIRISK T2 - COORAL Halbzeitsymposium CY - Hanover, Germany DA - 2011-11-24 PY - 2011 AN - OPUS4-27451 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmalenberger, A. A1 - Pritzkow, Wolfgang A1 - Ojeda, J.J. A1 - Noll, Matthias T1 - Characterization of main sulfur source of wood-degrading basidiomycetes by S K-edge X-ray absorption near edge spectroscopy (XANES) N2 - The main wood degraders in aerobic terrestrial ecosystems belong to the white- and brown-rot fungi, where their biomass can be created on wood decay only. However, total sulfur (S) concentration in wood is very low and only little is known about the different sulfur compounds in wood today. Sulfur-starved brown-rot fungi Gloeophyllum trabeum and Oligoporus placenta were incubated on sterilized pine wood blocks whereas Lentinus cyathiformis and the white-rot fungi Trametes versicolor were incubated on sterilized beech wood blocks. After 19 weeks of incubation, the S oxidation status was analyzed in wood, in degraded wood, and in biomass of wood-degrading fungi by synchrotron based S K-edge XANES, and total S and sulfate were quantified. Total sulfur and sulfate content in pine wood blocks were approximately 50 and 1 µg g-1, respectively, while in beech wood approximately 100 and 20 µg g-1 were found, respectively. Sulfur in beech was dominated by sulfate-esters. In contrast, pine wood also contained larger amounts of reduced S. Three out of four selected fungi caused a reduction of the S oxidation state in wood from oxidized S (sulfate-ester, sulfate) to intermediate S (sulfonate, sulfoxide) or reduced S (thiols, e.g., proteins, peptides, enzyme cofactors). Only O. placenta shifted thiol to sulfonate. Growth experiments of these fungi on selective minimal media showed that in particular cysteine (thiol), sulfonates, and sulfate enhanced total mycelium growth. Consequently, wood-degrading fungi were able to utilize a large variety of different wood S sources for growth but preferentially transformed in vivo sulfate-esters and thiol into biomass structures. KW - Basidiomycetes KW - Fungi KW - S K-edge X-ray absorption near edge spectroscopy (XANES) KW - Sulfur oxidation status KW - Sulfate-esters PY - 2011 DO - https://doi.org/10.1016/j.ibiod.2011.08.013 SN - 0964-8305 VL - 65 IS - 8 SP - 1215 EP - 1223 PB - Elsevier CY - Barking AN - OPUS4-27546 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Krug, Sonja A1 - Simon, S. ED - Brückle, I. ED - Hahn, O. ED - Bredekamp, H. T1 - Digital image analysis N2 - Comparatiye digital analysis was performed on the five moon drawings from the New York copy of the Sidereus Nuncius and the copperplate etchings printed in the Graz and Florence copies. The sequences of figures for the drawings on pages 8r, 9v and lOv demonstrate the process of digitally enhancing the black material on the drawings, isolating that material and then overlaying it on the etchings. Using an image editing program (Image Pro® Plus by Media Cybernetics) the black material on the drawings and the letterpress-printed text were isolated and segmented from the brown drawing media. As shown in Figs. 4, 6 and 8, the isolation was possible and the black material clearly overlaps the demarcation line in the drawings. To compare the drawn and printed images of each moon, the images were laid on top of each other with Adobe Photoshop® (Adobe Systems). In these images, the printed text was used for alignment and scale. By decreasing the opacity of the image on top, the lines of each image were compared. This technique revealed an almost one-to-one correlation between the demarcation line in the drawing (as indicated by the black material) and that on the etching. In each case, the similarities and concurrences by far outnumbered the minor deviations in line. One precondition of this work was that all the photographs be at the same angle, plane-parallel, so that the drawings could be compared with the etchings. A slight aberration in the plane could distort the geometry of the illustrations. Rectification of the image plane was carried out by means of the program metigo® MAP 2.2 (Fokus GmbH Leipzig). To validate the method, photographs from the same detail of the New York copy taken with different photographic cameras and different Parameters were rectified with metigo® MAP and compared in Adobe Photoshop®. The overlay of these photographs shows a good correlation in the layout of the lettering and moon figures with only small aberrations. The distribution of the black material on the drawings can be followed as clearly in the rectified photographs as in the unrectified photographs, the information is the same. PY - 2011 SN - 978-3-05-005095-9 SP - 94 EP - 97 PB - Akademie Verlag GmbH CY - Berlin AN - OPUS4-27538 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ewert, Uwe A1 - Heyne, Klara A1 - Zscherpel, Uwe A1 - Jechow, Mirko A1 - Bavendiek, K. ED - Thompson, D.O. ED - Chimenti, D.E. T1 - Optimum exposure conditions for computed radiography depending on fixed pattern noise and efficiency of imaging plate-scanner systems N2 - The presently active standards on Computed Radiography (CR) need a major revision. It was observed by many users that the image quality for class B of EN 14784-2 is not achievable under the same exposure conditions as used for film exposure. A mathematical model was developed and tested, which allows the calculation of the image quality, proven by image quality indicators (IQI), depending on the fixed pattern noise and the efficiency of the used imaging plate (IP) scanner system. All tested IP scanner systems provide a fixed correlation between the measured signal/noise ratio (SNR) and the grey values in the digital images. The maximum achievable SNRmax depends on the fixed pattern noise of the plate (high dose limit). Depending on the exposure dose an optimum visibility of IQIs can be predicted by calculation and measured considering the attenuation coefficient for calculation of the contrast/noise ratio (CNR). The diameter of the just visible wire is proportional to 1/sqrt(CNR). The optimum tube voltage for best visibility of IQIs and maximum CNR depend on the exposure dose. The optimum tube voltage for best visibility is achieved only at exposures with high dose. A dose dependant optimal tube voltage was not observed for film radiography. T2 - 37th Annual Review of Progress in Quantitative Nondestructive Evaluation CY - San Diego, CA, USA DA - 18.07.2010 KW - Computed radiography KW - Computed radiology KW - Non destructive testing KW - Image quality KW - Signal-to-noise ratio KW - Contrast-to-noise ratio KW - Imaging plates KW - Optimum tube voltage KW - Standards PY - 2011 SN - 978-0-7354-0888-3 DO - https://doi.org/10.1063/1.3591892 SN - 0743-0760 SN - 0094-243X N1 - Serientitel: AIP conference proceedings – Series title: AIP conference proceedings IS - 1335 SP - 493 EP - 500 PB - American Institute of Physics CY - Melville, NY AN - OPUS4-27540 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krug, Sonja T1 - Biozide & Kulturgüter T2 - BAM Abteilungskolloquium (Abteilung 4) CY - Berlin, Germany DA - 2011-12-15 PY - 2011 AN - OPUS4-27515 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Prasad M, K. A1 - Wiggenhauser, Herbert A1 - Balasubramaniam, Krishnan T1 - Detection of honeycomb defects in reinforced concrete structures using acoustic pulse-echo methods and wavelet transforms N2 - Honeycombs/compaction faults occur in the concrete structures due to improper solidification of the concrete, which may reduce the strength of the concrete and also act as a passage for the water/acids that further corrodes the reinforcements. This paper explores about the acoustic pulse-echo techniques for the detection of honeycomb defects in a laboratory specimen located at the Federal Institute for Materials Research and Testing (BAM), Berlin. Since concrete is an inhomogeneous medium, the defect Signals are masked by the material noise due to large amount of scattering/ reflections of acoustic waves. A filtering method using the discrete wavelet transforms is applied on the ultrasonic time Signals for the better localization of defects. KW - Honeycomb defects KW - Acoustic pulse-echo methods KW - Wavelets transforms PY - 2011 SN - 0973-9610 VL - 10 IS - 3 SP - 53 EP - 59 PB - ISNT CY - Chennai AN - OPUS4-27631 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gröschl, Christian A1 - Meyer-Scherf, Ronald A1 - Holtappels, Kai A1 - Kluge, Martin A1 - Eliezer, D. T1 - A new Technology for Hydrogen Safety: Glass Structures as a Storage System T2 - H2 - Expo CY - Hamburg, Germany DA - 2011-06-08 PY - 2011 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. N1 - Geburtsname von Meyer-Scherf, Ronald: Meyer, R. - Birth name of Meyer-Scherf, Ronald: Meyer, R. AN - OPUS4-27647 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meyer-Scherf, Ronald T1 - A new Technology for Hydrogen Safety: Glass Structures as a Storage System T2 - ICHS International Conference on Hydrogen Safety 2011 CY - San Francisco, CA, USA DA - 2011-09-12 PY - 2011 N1 - Geburtsname von Meyer-Scherf, Ronald: Meyer, R. - Birth name of Meyer-Scherf, Ronald: Meyer, R. AN - OPUS4-27702 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Rethmeier, Michael A1 - Weber, Gert A1 - Gaul, H. A1 - Brauser, Stephan T1 - Untersuchungen zur Ermüdungsfestigkeit von Widerstandspunktschweißverbindungen aus hochfesten Mehrphasenstählen unter Berücksichtigung fertigungsspezifischer Einflüsse N2 - Unter den rauen Bedingungen in der Automobilrohkarosseriefertigung lassen sich schweißbedingte Imperfektionen wie Risse beim Widerstandspunktschweißen von hochfesten Stählen nicht immer vermeiden. Für die sichere Auslegung ist die Kenntnis über den Einfluss solcher Risse von erheblicher Bedeutung. PY - 2011 SN - 978-3-942541-04-6 VL - P 802 SP - 1 EP - 86 PB - Verlag und Vertriebsgesellschaft mbH CY - Düsseldorf AN - OPUS4-25450 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schroeder, H. A1 - Müller, Urs A1 - Ziegert, C. ED - Hwang, H. ED - Kim, S. ED - Guillaud, H. ED - Gandreau, D. T1 - Building codes and standards in earth building - current situation in Germany N2 - Today, building is a complicated commercial process characterised by legalised agreements between all participants. For commercial building projects, all materials and constructions have to conform to building standards and regulations. Material properties must be reproducible in standardised test procedures. This also applies for the control of the quality of production of earth building materials and constructions. Building conservation is a part of this process. Generally, national building standards have to reflect the current situation of building materials / construction systems of that country for which they have been developed. T2 - TerrAsia 2011 - International conference on earthen architecture in Asia CY - Mokpo, Korea DA - 11.10.2011 KW - Standards KW - Germany KW - International KW - DIN KW - Lehmbau KW - Normen KW - Bauprodukte PY - 2011 SN - 978-89-92760-63-8 SP - 239 EP - 246 AN - OPUS4-25451 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Beke, S. A1 - Sugioka, K. A1 - Midorikawa, K. A1 - Bonse, Jörn ED - Hemsworth, E.J. T1 - Nanaosecond and femtosecond laser ablation of TeO2 crystals: surface characterization and plasma analysis N2 - Near-IR femtosecond (fs) (pulse duration = 150 fs, wavelength = 775 nm, repetition rate 1 kHz) and VUV nanosecond (ns) (pulse duration = 20 ns, wavelength = 157 nm, repetition rate 1 to 5 Hz) laser pulse ablation of single-crystalline TeO2 (c-TeO2 ) surfaces was performed in air using the direct focusing technique. A multi-method characterization using optical microscopy, atomic force microscopy and scanning electron microscopy revealed the surface morphology of the ablated craters. This allowed us at each irradiation site to characterize precisely the lateral and vertical dimensions of the laser-ablated craters for different laser pulse energies and number of laser pulses per spot. Based on the obtained information, we quantitatively determined the ablation threshold fluence for the fs laser irradiation when different pulse numbers were applied to the same spot using two independent extrapolation techniques. We found that in the case of NIR fs laser pulse irradiation, the ablation threshold significantly depends on the number of laser pulses applied to the same spot indicating that incubation effects play an important role in this material. In the case of VUV ns laser pulses, the ablation rate is significantly higher due to the high photon energy and the predominantly linear absorption in the material. These results are discussed on the basis of recent models of the interaction of laser pulses with dielectrics. In the second part of this chapter, we use time- of-flight mass spectrometry (TOFMS) to analyze the elemental composition of the ablation products generated upon laser irradiation of c-TeO2 with single fs- (pulse duration ~200 fs, wavelength 398 nm) and ns-pulses (pulse duration 4 ns, wavelength 355 nm). Due to the three order of magnitude different peak intensities of the ns- and fs laser pulses, significant differences were observed regarding the laser-induced species in the plasma plume. Positive singly, doubly and triply charged Te ions (Te+, Te2+, Te3+) in the form of many different isotopes were observed in case of both irradiations. In the case of the ns-laser ablation, the TeO+ formation was negligible compared to the fs case and there was no Te trimer (Te3+) formation observed. It was found that the amplitude of Te ion signals strongly depends on the applied laser pulse energy. Singly charged oxygen ions (O+) are always present as a byproduct in both kinds of laser ablation. KW - Tellurium dioxide crystals KW - Femtosecond laser ablation KW - VUV nanosecond laser ablation KW - Multiphoton absorption KW - Time-of-flight mass spectroscopy KW - Incubation KW - Optical properties KW - Scanning electron microscopy KW - Atomic force microscopy KW - Isotopes PY - 2011 SN - 978-1-61324-851-5 N1 - Serientitel: Physics Research and Technology – Series title: Physics Research and Technology IS - Chapter 4 SP - 77 EP - 96 PB - Nova Science Publishers, Inc. AN - OPUS4-25454 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blind, K. A1 - De Vries, H. A1 - Mangelsdorf, Axel ED - Fomin, V. ED - Jakobs, K. T1 - Openness for innovation and involvement in standardization: evidence from the community innovation survey N2 - In this paper, we explore the relationship between firms' approaches to open innovation and their decision to participate in Standardization alliances. Based on micro data of Dutch Companies surveyed in the Forth Community Innovation Survey we show that the importance of extemal knowledge is positively correlated with participation in Standardization. This suggests that firms aim to access the knowledge of other Companies and stakeholders in Order to increase their own knowledge base. The analysis also shows that firms cooperating with different actors are more likely to join Standardization. Due to the positive relationships with incoming knowledge spillovers and forms of Cooperation, we conclude that Standardization represents a specific form of collaborative knowledge-sharing and knowledge-creating strategy. In addition, we are able to show that absorptive capacity measured via Companies’ research intensity is promoting the involvement in Standardization. Besides the focus on knowledge and Cooperation variables, we explore the traditionally considered factors for alliances Formation and show that firm size, export activities and patent protection are positively correlated with participation in Standardization. T2 - 16th EURAS Annual standardisation conference - Standards for development CY - Kaunas, Lithuania DA - 08.06.2011 KW - Knowledge spillovers KW - Cooperation KW - Absorptive capacity KW - Standardisation PY - 2011 SN - 3-86130-629-8 SP - 19 EP - 36 PB - Wissenschaftsverlag Mainz CY - Aachen AN - OPUS4-25500 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mangelsdorf, Axel A1 - Portugal-Perez, A. A1 - Wilson, J. S. ED - Fomin, V. ED - Jakobs, K. T1 - Food standards and exports: evidence for China N2 - Using a new database on Standards in China, we estimate the impact of voluntaiy and mandatory Standards - either harmonized to international norms or purely domestic — on Chinese food exports. The data covers seven Chinese products over the period 1992-2008. We find that Standards have a positive effect on China's export performance, as the benefits to Standardization in terms of reducing potential Information asymmetiy and signaling enhance food safety and quality in foreign markets seem to surpass compliance costs. Our estimation results Show that the positive effect of Chinese Standards is larger when they are harmonized to international measures. The results suggest that there are clear benefits to China’s Steps to base their domestic Standards and regulations on international measures. T2 - 16th EURAS Annual standardisation conference - Standards for development CY - Kaunas, Lithuania DA - 08.06.2011 KW - Food standards KW - Trade barriers KW - SPS KW - TBT KW - Harmonization PY - 2011 SN - 3-86130-629-8 SP - 219 EP - 233 PB - Wissenschaftsverlag Mainz CY - Aachen AN - OPUS4-25501 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Blind, K. A1 - Mangelsdorf, Axel ED - Stober, R. T1 - Standards zur Qualitätssicherung (Art. 26 V DL-RL) aus ökonomischer Perspektive N2 - Aufgrund der Immaterialität von Dienstleistungen ist es dem Nachfrager von Dienstleistungen nur schwer möglich, vor dem Konsum die Qualität einer Dienstleistung einzuschätzen. Dementsprechend fehlt es oft an Vertrauen zwischen den Anbietern von Dienstleistungen und den Nachfragern. Das fehlende Vertrauen der Dienstleistungsnachfrager oder - anderes gesagt - die Informationsasymmetrien zwischen Käufer und Verkäufer erhöhen die Transaktionskosten und lassen einen Vertragsabschluss weniger wahrscheinlich werden. Das fehlende Vertrauen der Nachfrager in die Qualität von Dienstleistungen berührt nicht nur den inländischen Handel, sondern beeinträchtigt gerade den internationalen und damit auch den innereuropäischen Handel mit Dienstleistungen. Eine Eurobarometerumfrage aus dem Jahr 2002 zeigt, dass 26% der befragten europäischen Verbraucher einem Anbieter aus einem EU-Land außer ihrem eigenen weniger vertrauen als einem nationalen Anbieter. Aus dieser Umfrage ging ebenfalls hervor, dass die Verbraucher das Sicherheitsniveau von ausländischen Produkten und Dienstleistungen als geringer empfinden als Angebote aus ihrem eigenen Land. Das mangelnde Vertrauen der Nachfrager in ausländische Dienstleistungsanbieter ist auf die fehlende Transparenz der Dienstleistungsqualität und den damit implizierten Informationsasymmetrien zurückzuführen. Die im Dienstleistungssektor vorhandenen Informationsasymmetrien verursachen beachtliche volkswirtschaftliche Kosten bzw. Ineffizienzen, die im Vergleich zu den Produktmärkten ausgeprägter sind, da Produkteigenschaften im Gegensatz zu Eigenschaften von Dienstleistungscharakteristika auch für den Endverbraucher vor dem Kauf leichter zugänglich und auch besser nachprüfbar sind. KW - Food standards KW - Trade barriers KW - SPS KW - TBT KW - Harmonization PY - 2011 SN - 978-3-452-27634-6 SP - 73 EP - 103 PB - Carl Heymanns AN - OPUS4-25502 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Torge, Manfred A1 - Bücker, Michael A1 - Feldmann, Ines T1 - Modellhafte Evaluierung von Restaurierungs- und Konservierungsmaßnahmen an historischen Glasmalereien mit starken Schäden durch anthropogene Einflüsse N2 - In den Jahren von 1994 bis 2006 wurden zahlreiche Umweltprojekte zur Sanierung wertvoller historischen Glasmalereien aus dem Mittelalter und dem 19. Jahrhundert in national bedeutenden Bauensembles erfolgreich und modellhaft durchgeführt. Die dazu entwickelten Methoden und durchgeführten Arbeiten wurden auf ihre Wirksamkeit überprüft. Durch eine Erfassung der Belastungssituation im Spalt zwischen Original und Außenschutzverglasung sowie an der Innenseite des Originals lässt sich ermitteln, wie gut die Schutzwirkung gegen die Umweltlasten tatsächlich ist. Auf der Basis von Zustandsdokumentationen, die während der damaligen Restaurierung angefertigt wurden, können durch den Vergleich mit dem gegenwärtigen Zustand inzwischen eingetretene Materialveränderungen charakterisiert werden. Messungen der Staubbelastung und die Analyse ihrer Kornfraktionen und der chemischen Zusammensetzung ermöglichten eine quantitative Ermittlung der Wirkung von Feinstaub. Die Tatsache, dass jedes Originalfenster hinter einer fachgerechten Schutzverglasung vor einer direkten Belastung mit Kondenswasser bewahrt wird, hat sich auch an den evaluierten fünf Objekten bestätigt. An der allgemein positiven Wirkung dieser Konservierungsmaßnahme gibt es keinen Zweifel. KW - Außenschutzverglasung KW - Klima KW - Staub PY - 2011 SN - 978-3-8167-8638-2 VL - D 1013 SP - 1 EP - 187 PB - Fraunhofer IRB Verl. CY - Stuttgart AN - OPUS4-25514 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vasilic, Ksenija A1 - Meng, Birgit A1 - Kühne, Hans-Carsten A1 - Roussel, N. T1 - Flow of fresh concrete through steel bars: a porous medium analogy N2 - Although being a very promising area of concrete technology, computational modeling of fresh concrete flow is a comprehensive and time consuming task. The complexity and required computation time are additionally increased when simulating casting of heavily reinforced sections, where each single reinforcement bar has to be modeled. In order to improve the computation speed and to get closer to a practical tool for simulation of casting processes, an innovative approach to model reinforced sections is proposed here. The basic idea of this approach is to treat the reinforcement zone as a porous medium in which a concrete is propagating. In the present paper, the numerical implementation of this concept is described. A methodology allowing for the computation of the equivalent permeability of the steel bars network is suggested. Finally, this numerical technique efficiency is evaluated by a comparison with experimental results of model fluids casting in model formworks. KW - Fresh concrete (A) KW - Rheology (A) KW - Modeling (E) KW - Permeability (C) KW - Yield stress KW - Simulation KW - Flow of mortar KW - Flow of concrete PY - 2011 DO - https://doi.org/10.1016/j.cemconres.2011.01.013 SN - 0008-8846 SN - 1873-3948 VL - 41 IS - 5 SP - 496 EP - 503 PB - Pergamon Press CY - New York, NY AN - OPUS4-25532 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pfennig, Anja A1 - Kranzmann, Axel T1 - Reliability of pipe steels with different amounts of C and Cr during onshore carbon dioxide injection N2 - During the compression of emission gasses into deep geological layers (Carbon Dioxide Capture and Storage, CCS) CO2-corrosion will become a relevant safety issue. The reliability of the steels used at a geological onshore CCS-site in the Northern German Bassin 42CrMo4 (1.7225, AISI 4140) used for casing, and the injection pipe steels X46Cr13 (1.4034, AISI 420 C), X20Cr13 (1.4021, AISI 420 J) as well as X35CrMo17 (1.4122) is demonstrated in laboratory experiments. Samples were kept in a synthetic aquifer environment at T = 60 °C. This corrosive environment is then saturated with technical CO2 at a flow rate of 3 l/h. Microstructures were characterized by X-ray diffraction, light microscopy, scanning electron microscopy, and energy dispersive X-ray analysis, after a series of heat treatments (700 h to 2 years). The non-linear isothermal surface corrosion behaviour of the steels reveals surface corrosion rates around 0.1–0.8 mm/year, when obtained by mass gain. Severe pit corrosion (pit heights ca. 4.5 mm) are only located on the injection pipe steels. Main phases of the continuous scales are siderite FeCO3 and goethite α-FeOOH. The formation of the non-protective layer is likely to form via a transient Fe(OH)2-phase. KW - Steel KW - Pipe KW - Corrosion KW - Carbonate layer KW - CO2-injection KW - CO2-storage CCS PY - 2011 DO - https://doi.org/10.1016/j.ijggc.2011.03.006 SN - 1750-5836 VL - 5 IS - 4 SP - 757 EP - 769 PB - Elsevier CY - New York, NY [u.a.] AN - OPUS4-25533 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfennig, Anja A1 - Schulz, Sabrina A1 - Linke, Barbara A1 - Kranzmann, Axel T1 - Supercritical CO2-corrosion in pipe steels during carbon capture and storage CCS N2 - The CCS technique involves the compression of emission gasses in deep geological layers. To guarantee the safety of the site, C02-corrosion of the injection pipe steels has to be given special attention when engineering CCSsites. To get to know the corrosion behaviour samples of the heat treated Steel 1.72252CrMo4, used for casing, and the stainless injection-pipe Steel 1.4034 X46Cr 13 were kept at T=60 °C and ambient pressure as well as p=100 bar for 700 h - 8000 h in a C02-saturated synthetic aquifer environment similar to possible geological on-shore CCS-sites in the northern German Basin. The isothermal corrosion behaviour obtained by mass gain of the steels in the gas phase, the liquid phase and the intermediate phase gives surface corrosion rates around 0.1 to 0.8 mm/year at ambient pressure and much lower about 0.02 to 0.2 mm/year at 100 bar where the C02 is in its supercritical state. Severe pit corrosion with pit heights around 4.5 mm are only located on the 42CrMo4 Steel. Main phase of the continuous complicated multi-layered carbonate/oxide structure is siderite FeCO} in both types of Steel. T2 - 4th International conference on sustainable energy and environment (SEE 2011) - A paradigm shift to low carbon society CY - Bangkok, Thailand DA - 23.11.2011 KW - Steel KW - Pipeline KW - Corrosion KW - Carbonate layer KW - CCS KW - Supercritical CO2- KW - CO2-storage PY - 2011 SP - 1 EP - 6 AN - OPUS4-25534 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfennig, Anja A1 - Linke, Barbara A1 - Schulz, Sabrina A1 - Kranzmann, Axel T1 - Supercritical CO2-corrosion in pipe steels during carbon capture and storage CCS N2 - The CCS technique involves the compression of emission gasses in deep geological layers. To guarantee the safety of the site, CC>2-corrosion of the injection pipe steels has to be given special attention when engineering CCS-sites. To get to know the corrosion behaviour samples of the heat treated Steel 1.72252CrMo4, used for casing, and the stainless injection-pipe Steel 1.4034 X46Crl3 were kept at T=60 °C and ambient pressure as well as p=100 bar for 700 h - 8000 h in a CC>2-saturated synthetic aquifer environment similar to possible geological onshore CCS-sites in the northern German Basin. The isothermal corrosion behaviour obtained by mass gain of the steels in the gas phase, the liquid phase and the intermediate phase gives surface corrosion rates around 0.1 to 0.8 mm/year at ambient pressure and much lower about 0.02 to 0.2 mm/year at 100 bar where the CO2 is in its supercritical state. Severe pit corrosion with pit heights around 4.5 mm are only located on the 42CrMo4 Steel. Main phase of the continuous complicated multi-layered carbonate/oxide structure is siderite FeCCh in both types of Steel. T2 - 3rd International congress on green process engineering (GPE 2011) CY - Kuala-Lumpur, Malaysia DA - 06.12.2011 KW - Steel KW - Pipeline KW - Corrosion KW - Carbonate layer KW - CCS KW - Supercritical CO2- KW - CO2-storage PY - 2011 SP - 1 EP - 6 AN - OPUS4-25535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfennig, Anja A1 - Wojtas, P. A1 - Spengler, I. A1 - Kranzmann, Axel T1 - Effect of heat treatment of injection pipe steels on the formation of local corrosion in CCS-environment N2 - When engineering a Carbon Capture and Storage site (CCS) local corrosion (pitting) of the injection pipe steel may become an issue when emission gasses from oxyfuel power plants are compressed into deep geological layers. This highly corrosive environment arises when the flue gasses, mainly composed of CO2 , are injected into saline aquifer water. Immediately carbonic acid is formed causing corrosive attack of the injection steels. The influence of heat treatment on the local corrosion resistance was demonstrated in laboratory experiments at 60 °C and ambient pressure for three steels X46Cr13 (1.4034), X20Cr13 (1.4021) and X5CrNiCuNb16-4 (1.4543) under a similar liquid corrosive environment as found at a geological onshore CCS-site in the Northern German Bassin. T2 - 2nd Oxyfuel combustion conference CY - Yeppoon, Queensland, Australia DA - 12.09.2011 KW - Steel KW - Pipe KW - Corrosion KW - Heat treatment KW - CO2-injection KW - CO2-storage CCS KW - Carbonate KW - Ambient pressure KW - CCS KW - Steels PY - 2011 SP - 1 EP - 3 AN - OPUS4-25536 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rigo, E. A1 - Rosner, Martin A1 - Vogl, Jochen T1 - Herkunftsbestimmung von Kalken N2 - Analytische Methoden zur Feststellung der Herkunft eines Baustoffes sind bislang kaum entwickelt worden. In Deutschland gibt es eine Reihe von Kalkiagerstätten, die in unterschiedlichen geologischen Formationen Kalk oder Dolomit enthalten. Das unterschiedliche geologische Alter von Kalken sowie die ursprüngliche mineralische Zusammensetzung und die geologische Historie spiegeln sich im 87Sr/88Sr-lsotopenverhältnis weder. Mittels der Thermionen-Massenspektrometrie kann dieses Verhältnis ermittelt und somit zur Herkunftsbestimmung eines Kalkes herangezogen werden. T2 - GDCh-Fachtagung Bauchemie 2011 CY - Hamburg-Harburg, Deutschland DA - 06.10.2011 KW - Isotopenverhältnisse KW - Kalke KW - Herkunft KW - TIMS PY - 2011 SN - 978-3-936028-69-0 N1 - Serientitel: GDCh-Monographien – Series title: GDCh-Monographien VL - 44 SP - 282 EP - 284 CY - Frankfurt/M. AN - OPUS4-25576 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Shokouhi, Parisa A1 - Wöstmann, Jens A1 - Schneider, Gerhard A1 - Milmann, Boris A1 - Taffe, Alexander A1 - Wiggenhauser, Herbert T1 - Nondestructive detection of delamination in concrete slabs - multiple-method investigation N2 - The delamination of concrete slabs is the separation along a plane roughly parallel to, and generally near, the surface. Corrosion-induced delamination is a common problem in old concrete bridge decks. If undetected, delaminations could expand, reach the surface, and result in spalling. Early detection of delamination is necessary for planning timely repairs that prevent costly deck replacement projects. Most bridge owners rely on routine visual and traditional surveys of bridge deck conditions. These surveys are highly subjective and can locate only large shallow delaminated zones. Several nondestructive testing (NDT) techniques have recently been employed for bridge deck evaluation to obtain more objective and comprehensive assessment. The reliability of applicable methods needs to be established before a greater role for NDT in routine inspections can be encouraged. This paper presents a validation study aimed at evaluating the effectiveness of three NDT techniques, namely impact echo, ultrasound (US) echo, and US linear array, in detection of delamination. This study is unique because the subject test specimens were deteriorated bridge deck segments preserved from the demolition of a prestressed box girder bridge. The results of the tests conducted on one of the specimens are presented and discussed here: impact echo provided satisfactory overall assessment, but the individual results were often difficult to interpret; US echo detected deep delaminations but not shallow ones; and US linear array located the extent of deep delaminations and provided indications of shallow ones. KW - Delamination KW - Concrete KW - Ultrasonic testing KW - Impact echo KW - Scanning PY - 2011 DO - https://doi.org/10.3141/2251-11 SN - 0361-1981 VL - 2251 SP - 103 EP - 113 PB - National Research Council CY - Washington, DC AN - OPUS4-25552 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Raedel, Martina A1 - Torge, Manfred A1 - Bücker, Michael T1 - Adhesives for stained glass windows - development of a new system for wide cracks N2 - To improve the adhesives used for restoring stained glass windows, various adhesives were tested and modified. Stained glass windows often show gaps that are too wide to be glued with conventional adhesives, and complementing the gap with spare glass is very time-consuming. To solve this problem, a filler with improved adhesive strength was developed to bridge wider gaps and cracks. The new filler combines glass adhesives with specially treated glass powder. Three different glass adhesives were selected and mixed with the specially treated glass powder. The adhesive – glass powder mixture developed was then subjected to accelerated aging and analysed with Fourier transform infrared analysis, scanning electron microscopy, colourimetry, and bending and tensile tests. The results were excellent and the mixture was subsequently used to restore glass windows from four 19th-century churches and chapels. The restoration process was described in conjunction with the advantages of using this approach. This new adhesive – glass powder mixture provides an adhesive process that can be adapted to the special needs of any object being restored and thus provides a ready answer to the specific damage of each object. T2 - CCI Symposium 2011 - Adhesives and consolidants for conservation: research and applications CY - Ottawa, Canada DA - 17.10.2011 KW - Adhesives KW - Stained glass windows KW - Conservation KW - Restoration KW - New adhesive for wide cracks PY - 2011 UR - http://www.cci-icc.gc.ca/symposium/2011/Paper%2034%20-%20Raedel%20et%20al.%20-%20English.pdf SP - 1 EP - 21 AN - OPUS4-25549 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Werrel, Martin A1 - Deubel, Jan A1 - Krüger, Simone T1 - Vitiated Cone Calorimeter - eiin Modell zur szenarioabhängigen Beurteilung von Brandgefahren? T2 - Doktorandentag des Lehrstuhles Anlagentechnik und Anlagensicherheit der OvGU CY - Magdeburg, Germany DA - 09.12.2011 PY - 2011 AN - OPUS4-25569 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Oliver A1 - Litzba, Andreas A1 - Kalbe, Ute A1 - Berger, Wolfgang T1 - Comparison of colum and batch test eluates derived from PAH- and TPH-contaminated soils T2 - EMEC12 CY - Clermont-Ferrand, France DA - 2011-12-07 PY - 2011 AN - OPUS4-25587 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Licha, K. A1 - Resch-Genger, Ute T1 - Probes for optical imaging: new developments N2 - Recent developments of fluorescent probes beyond approved indocyanine green (ICG) – itself increasingly spreading into new imaging applications like lymphatic mapping, arthritis imaging and tumor surgery – exploit various photophysical and biochemical mechanisms to monitor molecular events with higher specificity and accuracy. Emphasizing nanoparticulate formulations, targeted conjugates, activatable probes, probes with a sensor function and multimodality probes, this review discusses advantages and limitations of each type of probe, thereby critically assessing the desired translation into the clinic. KW - Fluorescence KW - Dye KW - Probe KW - Optical imaging KW - Method comparison KW - Particle KW - NIR KW - Probe design PY - 2011 DO - https://doi.org/10.1016/j.ddtec.2011.11.003 SN - 1740-6749 VL - 8 IS - 2-4 SP - e87 EP - e94 PB - Elsevier CY - Amsterdam AN - OPUS4-25936 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nie, Yaru A1 - Hübert, Thomas T1 - Effect of carbon nanofiber (CNF) silanization on the properties of CNF/epoxy nanocomposites N2 - Carbon nanofibers (CNFs) were functionalized by a multistage process including oxidation, reduction and silanization. The chemical modifications were examined by Fourier transform infrared spectroscopy, X-ray photoelectron spectrometry, Raman spectroscopy and thermogravimetric analysis. The silanized CNFs were then added into an epoxy resin (EPON 828) to study the effect of the surface modification of CNFs on the properties of nanocomposites. For comparison, nanocomposites containing original unmodified CNFs were also investigated. Scanning electron microscopy indicates better dispersion of modified fibers in the epoxy polymer matrix; the mechanical and thermal properties of composites are also improved; the electrical conductivity of the composites is reduced. KW - Carbon nanofibers KW - Epoxy composites KW - Silanization KW - Electrical conductivity KW - Thermal conductivity KW - Mechanical properties PY - 2011 DO - https://doi.org/10.1002/pi.3124 SN - 0959-8103 SN - 1097-0126 SN - 0007-1641 VL - 60 IS - 11 SP - 1574 EP - 1580 PB - Wiley InterScience CY - Chichester, West Sussex AN - OPUS4-25865 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Robens, E. A1 - Rübner, Katrin A1 - Klobes, Peter A1 - Balköse, Gulsum Devrim ED - Okada, C.T. T1 - Water vapour sorption and humidity - a survey on measuring methods and standards N2 - Under environmental conditions water exists in all three classical States of matter: solid, liquid and gas. The water molecule is non-linear and therefore polar. In comparison with other liquids water has anomalous features; about 63 exceptional properties are recorded. This article starts with reviewing properties of water, typical occurrences and definitions such as relative and absolute humidity and moisture content. Water is present everywhere in nature and engineering; it may be helpful or harmful. The survey concerns both: atmospheric hygrometry and usual measuring methods of the moisture content of solids and liquids as well as water Sorption. The determination of the atmospheric humidity is among the more difficult problems in metrology. In contrast, humidity determination of materials is simple; however the definition of the dry state is difficult. Because water is bound at and in solids and liquids in many different ways it tums out that the humidity content of materials is difficult to define and to measure accurately. We provide a survey on the measuring methods, describe the most important ones and discuss advantages and accuracy. In the search for extraterrestrial water special remote measuring methods have been developed analysing the spectrum of electromagnetic radiation either of natural sources or produced by a probe and reflected. Spacious deposits have been detected photographically. In situ investigations are made using conventional methods. With regard to the problems of measurements, Standardisation of measuring methods and procedures is required. There exist many institutions, which are engaged in investigating the use of water and standardising measuring methods. In tabular form, we give a survey on existing Standards. PY - 2011 SN - 978-1-61209-246-1 N1 - Serientitel: Environmental remediation technologies, regulations and safety – Series title: Environmental remediation technologies, regulations and safety IS - Chapter 1 SP - 1 EP - 91 PB - Nova Science Publishers, Inc. CY - New York AN - OPUS4-26290 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vercoutère, C. A1 - Müller, K. A1 - Chiotti, L. A1 - Nespoulet, R. A1 - Staude, Andreas A1 - Riesemeier, Heinrich A1 - Reiche, I. T1 - Rectangular beads from the final gravettian level of the Abri Pataud: raw material identification and its archaeological implications N2 - The Final Gravettian level (level 2) of the abri Pataud (Dordogne, France) yielded a large assemblage of body ornaments that consists essentially of 85 quite standardized rectangular beads. Some uncertainty remained about the raw material in which these small beads were made: mammoth ivory, reindeer antler or bone? Non-invasive methods were employed in order to determine the raw material. First chemical analyses using microbeam Proton Induced X-ray Emission analysis (microPIXE) did not enable us to conclude definitively. Therefore, synchrotron and laboratory X-ray microtomography (microCT) were applied on eight beads and allowed us to identify ivory for all of them except for one, which shows slightly different morphological features. KW - Abri Pataud KW - Gravettien final KW - Ivoire de mammouth KW - MicroPIXE KW - MicroCT KW - Perles rectangulaires KW - Final Gravettian KW - Mammoth ivory KW - Rectangular beads PY - 2011 SN - 1960-1360 VL - 35 SP - 259 EP - 271 PB - Presses Univ. de Rennes CY - Rennes AN - OPUS4-26250 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neuschaefer-Rube, U. A1 - Bartscher, M. A1 - Schulze, M. A1 - Neukamm, M. A1 - Staude, Andreas A1 - Goebbels, Jürgen T1 - Messung von Mikrogeometrien mit industrieller Computertomographie N2 - Die industrielle Computertomographie (CT) ist ein gut bekanntes Verfahren zur zerstörungsfreien Prüfung von Werkstücken. In den letzten Jahren wird die CT aber zunehmend auch für dimensioneile Messungen von Werkstücken eingesetzt. Der wesentliche Vorteil der CT liegt in der Kompletterfassung mit hoher Messpunktdichte, die auch für andere Messverfahren unzugängliche, innere Geometrien einschließt. An kleinen Bauteilen können Strukturen bis herunter zu wenigen Mikrometern gemessen werden, wodurch sich das Verfahren gut für die Messung von Mikroteilen eignet. Nachteilig ist, dass viele Einflussgrößen das Messergebnis beeinflussen, was die Rückführung der Messergebnisse, die Bestimmung der Messunsicherheit und die Definition von Spezifikationen für CT-Anlagen erschwert. Der Beitrag stellt nach einer Einführung in das Verfahren Anwendungsbeispiele der CT an Mikroteilen vor. Darüber hinaus geht der Beitrag auf Prüfkörper und -verfahren zur Einmessung und Überprüfung von CT-Anlagen ein und berichtet über aktuelle Normungsaktivitäten. Abschließend werden Möglichkeiten zur weiteren Steigerung der Auflösung aufgezeigt, um zukünftig möglicherweise auch Nanogeometrien messen zu können. T2 - 4. Fachtagung Metrologie in der Mikro- und Nanotechnik 2011 - Messprinzipien - Messgeräte - Anwendungen CY - Erlangen, Germany DA - 25.10.2011 PY - 2011 SN - 978-3-18-092133-4 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte VL - 2133 SP - 137 EP - 148 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-26251 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Igartua, A. A1 - Fernandez, X. A1 - Woydt, Mathias A1 - Luther, R. A1 - Illarramendi, I. ED - Lakshminarayanan, P.A. ED - Nayak, N.S. T1 - Tribological tests to simulate wear on piston rings N2 - In order to reduce experimental effort, tribological tests are performed for coating selection, simulating the friction, wear and scuffing behaviour between the piston ring and cylinder liner, as well as lubricant evaluation. The creation of test standards in piston ring/cylinder liner simulation is discussed. PVD coatings, HVOF coatings and nitriding treatments have been applied to piston rings as alternative for chromium coatings. CrN/TiN coating seems very effective for increasing the wear and scuffing resistance. Biodegradable engine oils based on esters and polyglycols reduce friction and exceed the wear resistance of reference engine oils based on hydrocarbons for the new generation engines with high cylinder pressures. KW - Friction KW - HVOF KW - Chromium KW - CrN/TiN KW - Scuffing KW - Wear KW - Resistance KW - Tribo-system KW - Piston ring KW - Cylinder liner KW - SRV Test KW - Schwingung KW - Reibung KW - Verschleiß KW - Oscillation KW - Friction and Wear KW - Extreme pressure test KW - Coating KW - Physical vapour deposited coating (PVD) KW - High Pressure–High Velocity Oxi-fuel coating (HP-HVOF) KW - Friction coefficient KW - Wear scar KW - Lubricant KW - Bio-degradable lubricant KW - Ester KW - Glycol KW - Viscosity index KW - Viscosity grade KW - Thematic piston ring PY - 2011 SN - 978-0-470-82882-3 DO - https://doi.org/10.1002/9780470828847.ch11 IS - Chapter 11 SP - 167 EP - 195 PB - John Wiley & Sons AN - OPUS4-26253 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Barheine, Sabrina A1 - Hayakawa, S. A1 - Jäger, Christian A1 - Shirosaki, Y. A1 - Osaka, A. T1 - Effect of disordered structure of boron-containing calcium phosphates on their in vitro biodegradability N2 - This study proposes a new guideline for designing biodegradable apatite ceramics. Boron-containing hydroxyapatite (BHAp) particles were prepared by a high-temperature solid-state reaction processing method and were characterized in terms of their chemical composition, apatite lattice defects and in vitro biodegradability. Solid-state nuclear magnetic resonance analysis showed that boron-incorporation into hydroxyapatite (HAp) derived by thermo-chemical reactions between borate and calcium phosphate phases led to disordered phases (BCaP) of a CaO–P2O5–B2O3–OH system covering the crystalline HAp core. X-ray diffraction analysis indicated that the BCaP phase must consist mainly of a crystalline oxyboroapatite (OBAp) phase. An in vitro biodegradability test showed that BHAp degraded quicker than HAp or ß-tricalcium phosphate. The biodegradability of BHAp particles can be controlled by boron incorporation into a HAp lattice leading to the formation of a disordered OBAp phase. KW - Boron KW - Hydroxyapatite KW - Calcium phosphate KW - NMR KW - Biodegradability KW - Disorder KW - Oxyboboapatite PY - 2011 DO - https://doi.org/10.1111/j.1551-2916.2011.04400.x SN - 0002-7820 SN - 1551-2916 VL - 94 IS - 8 SP - 2656 EP - 2662 PB - Blackwell Publishing CY - Malden AN - OPUS4-26244 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - König, R. A1 - Scholz, G. A1 - Veiczi, M. A1 - Jäger, Christian A1 - Troyanov, S.I. A1 - Kemnitz, E. T1 - New crystalline aluminium alkoxide oxide fluorides: evidence of the mechanism of the fluorolytic sol-gel reaction N2 - This study reports three new crystalline aluminum isopropoxide oxide fluorides with molar ratios of Al:F equal to 1:1 and 1:1.25. These are the first three representatives isolated without the incorporation of external donor molecules. Compound 1 Al4F4(µ4-O)(µ-O'Pr)5[H(O'Pr)2] contains a tetranuclear unit consisting of two different five fold coordinated AlFO4-units, with F exclusively in the terminal position. Compound 2, Al4F4(µ4-O)(µ-O'Pr)5[H(O'Pr)2]·Al5F5(µ5-O)(µ-O'Pr)8, contains both a tetranuclear unit (as in 1) and a pentanuclear Al-unit. Al-atoms in the latter are five- and six fold coordinated. Compound 3, Al16F20(µ4-O)4(µ-O'Pr)20·2('PrOH), exhibits a slightly higher fluorination degree and contains an oligomeric chain of four F-linked tetranuclear Al-units. In addition to X-ray structure analysis, compound 1 was characterized by different solid state MAS NMR techniques, including 27Al triple quantum MAS NMR and 1H, 1H→13C CP, 19F and 27Al MAS NMR. On the basis of the collected data, a reliable decomposition of 27Al single pulse MAS NMR spectra and an unambiguous assignment of the resonances to the respective structural AlFO4-units are given. The new crystalline aluminum isopropoxide oxide fluorides are direct evidence of the fluorolytic sol–gel mechanism previously discussed. KW - Aluminium fluorine KW - MAS NMR KW - Qudrupolar nuclei KW - Crystalline aluminium isopropoxide fluoride PY - 2011 DO - https://doi.org/10.1039/c1dt10514k SN - 1477-9226 SN - 1477-9234 SN - 1364-5447 VL - 40 IS - 34 SP - 8701 EP - 8710 PB - RSC CY - Cambridge AN - OPUS4-26245 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lai Wai-Lok, Wallace A1 - Kind, Thomas A1 - Wiggenhauser, Herbert T1 - Using ground penetrating radar and time-frequency analysis to characterize construction materials N2 - For decades, applications of nondestructive evaluation-civil engineering (NDE-CE) focus on object identifications (such as steel bars, tendon ducts and backwall reflections) in infrastructures. Because of the advantage of efficient visualization of internal structure, utilization of these methods can probably be extended to material characterization (MC) of aging and adversely exposed infrastructures. However, two factors yield a big gap between NDE and MC. First, for the ease of visualization, the primary focus of NDE-signal processing is object identification, which usually alters the originality of the signal. Second, there is lack of relationship and inverse models bridging the NDE-derived and conventional material properties compared to other disciplines of science, such as geophysics. These disadvantages make laboratory and field-scale NDE-MC still a far-reaching holy grail and is possibly the greatest hurdle to be regularly adopted in CE structures. This paper attempts to address this gap from object identification to MC using ground penetrating radar (GPR) as one of the most frequently used NDE-CE methods, and signal processing with joint time–frequency domain (JTFA) analysis. Three examples of material property characterization regarding the individual effects of steel bar corrosion in concrete, hydration and moisture content distribution of construction materials are given. KW - Ground penetrating radar KW - Time-frequency analysis KW - Construction materials KW - Short time fourier transform PY - 2011 DO - https://doi.org/10.1016/j.ndteint.2010.10.002 SN - 0963-8695 VL - 44 IS - 1 SP - 111 EP - 120 PB - Butterworth-Heinemann CY - Oxford AN - OPUS4-26288 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lai Wai-Lok, Wallace A1 - Kind, Thomas A1 - Wiggenhauser, Herbert T1 - Frequency-dependent dispersion of high-frequency ground penetrating radar wave in concrete N2 - This paper studies the dielectric dispersion of high frequency radar wave in concrete in early-aged and hardened concrete specimens. Frequency-dependent spectra of phase velocity ν(ω) were measured to deduce the spectra of real part of dielectric permittivity ε'(ω). The dispersion was measured by three high nominal ground penetrating radar frequencies (1.5, 1.6 and 2.6 GHz), experimenting on two steel bars with concrete cover 50 and 100 mm. It was found that ν(ω) and ε'(ω) dispersed at lower frequency, but became stable at high frequency regions, which agrees with the classical GPR plateau. The same frequency components at different nominal antenna frequencies show a close range of ν(ω) and ε'(ω) in concrete of different ages. The results in this paper warrant further investigation of using GPR wave to study material properties. KW - Frequency-dependent dielectric dispersion KW - Ground penetrating radar (GPR) KW - Phase velocity KW - Real part of dielectric permittivity KW - Concrete PY - 2011 DO - https://doi.org/10.1016/j.ndteint.2010.12.004 SN - 0963-8695 VL - 44 IS - 3 SP - 267 EP - 273 PB - Butterworth-Heinemann CY - Oxford AN - OPUS4-26289 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Döring, Joachim A1 - Bartusch, Jürgen A1 - Brekow, Gerhard A1 - Kreutzbruck, Marc A1 - Hillger, W. A1 - Bovtun, V. T1 - Luftultraschall-Prüfköpfe mit 3kV-Impuls-Ansteuerung T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-26224 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hassler, J. A1 - Barth, P. A1 - Richter, Silke A1 - Matschat, Ralf T1 - Determination of trace elements in high-purity copper by ETV-ICP OES using halocarbons as chemical modifiers N2 - Inspired by the globule arc technique a new electrothermal vaporization inductively coupled plasma optical emission spectrometry (ETV-ICP OES) method was developed for the analysis of high-purity copper materials. The performance of the method was investigated for the analytes Ag, Al, As, Bi, Cd, Co, Cr, Fe, Mg, Mn, Ni, P, Pb, S, Sb, Se, Si, Sn, Te, Ti, Zn and Zr. ETV parameters were optimized regarding the release of the analytes, the transport efficiency and the quality of analytical results in terms of precision, trueness and power of detection. The influence of CCl2F2, CHClF2, C2H2F4 and CHF3 as gaseous halogenation modifiers was investigated. A sufficient in situ analyte matrix separation was achieved by using CHF3 as halogenating reagent avoiding a high matrix input from the molten copper sample into the ETV system and the plasma. A complete release from the samples was obtained for all investigated analytes except Se and Te. Acceptable results for the determination of the trace elements Ag, Al, As, Bi, Cd, Co, Cr, Fe, Mg, Mn, Ni, P, Pb, S, Sb, Si, Sn, Ti, Zn and Zr in high-purity copper were achieved. The method includes a preceding sample preparation step of oxidizing the surface of copper samples which results in a significantly enhanced sensitivity. In addition to the calibration with copper samples, the feasibility of the calibration with liquid multi-element solutions was investigated. Except for Ag, Mg and Ni all analytes could be analyzed using aqueous calibration solutions. The trueness of the method was tested by the determination of analyte contents of certified reference materials. Limits of quantification ranging from 0.6 ng g-1 to 29 ng g-1 were achieved. The developed direct solid sampling method is time and cost effective and well suited for the characterization of high-purity copper materials. The method can be automated to a large extent and is applicable for processes accompanying analyses. In contrast to all other investigated trace elements, Se and Te were not released from the matrix at measurable levels under the used conditions. The determination of these elements is still under investigation and will be reported in a succeeding publication. KW - ETV KW - Copper KW - Impurities PY - 2011 DO - https://doi.org/10.1039/c1ja10149h SN - 0267-9477 SN - 1364-5544 VL - 26 IS - 12 SP - 2404 EP - 2418 PB - Royal Society of Chemistry CY - London AN - OPUS4-29615 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingbeil, Dietmar T1 - Nicht-lokale Schädigungsmodelle bei großen Dehnraten T2 - Kolloquium über Werkstoffmodellierung CY - Stuttgart, Germany DA - 2011-06-09 PY - 2011 AN - OPUS4-29595 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klingbeil, Dietmar T1 - Non-local damage models at high strain rates T2 - Workshop on Phase separation, Damage and Fracture CY - Berlin, Germany DA - 2011-09-21 PY - 2011 AN - OPUS4-29596 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Jörg A1 - Pentzien, Simone A1 - Koter, Robert T1 - Cleaning of soiled paper model samples using short and ultrashort laser pulses T2 - Konferenz "New Approaches to Book and Paper Conservation-Restoration" CY - Horn, Austria DA - 2011-05-09 PY - 2011 AN - OPUS4-21839 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Joshi, Ranjit A1 - Friedrich, Jörg Florian A1 - Wagner, M. T1 - Role of hydrogen peroxide in selective OH group functionalization of polypropylene surfaces using underwater capillary discharge N2 - Plasma chemical methods are well suited for introducing functional groups to the surfaces of chemically inert polymers such as polyolefins. However, a broad variety of functional groups are often formed. Unfortunately, for further chemical processing such as grafting of molecules for advanced applications a highly dense monotype functionalized polyolefin surface is needed. Therefore, the main task was to develop a selective surface functionalization process, which formed preferably only a single type of functional groups at the surface in high concentration. Amongst the novel plasma methods, the underwater plasma process (UWP) is one of most attractive options to solve the problem of monotype functionalization. Such plasma is an efficient source of ions, electrons, UV-radiation, high-frequency shock waves, radicals such as hydroxyl radical, and reactive neutral molecules such as hydrogen peroxide. In contrast to established gas phase glow discharge processes, the water phase limits the particle and radiation energies and thus the energy input into the polymer. By virtue of the liquid water environment, which moderates highly energetic plasma species, extensive oxidation, degradation, cross-linking and radical formation on the polymer are more limited as compared to gas plasma exposure. The variety of plasma produced species in the water phase is also much smaller because of the limited reaction possibilities of the plasma with water. The possibility to admix a broad variety of chemical additives makes underwater plasma even more attractive. Hydrogen peroxide and the catalyst (Fe-ZSM5) should influence and increase the equilibrium concentration of OH radicals in the underwater plasma process. It was found that these radicals played a very important role in OH functionalization of polyolefin surfaces. Hydrogen peroxide was identified to be the most prominent precursor for OH group formation in the UWP. The catalyst would affect the steady state of OH radical formation and its reaction with the substrate surface and thus accelerates the functionalization process. KW - Surface modification KW - Polymer functionalization KW - Underwater plasma KW - Capillary discharge KW - Hydroxyl functionalization KW - Hydrogen peroxide KW - Hydroperoxyl radicals KW - Heterogeneous catalysis KW - Fenton-like processes PY - 2011 DO - https://doi.org/10.1163/016942410X520862 SN - 0169-4243 SN - 1568-5616 VL - 25 SP - 283 EP - 305 PB - VNU Science Press CY - Utrecht AN - OPUS4-22413 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schwibbert, Karin A1 - Marin-Sanguino, A. A1 - Bagyan, I. A1 - Heidrich, Gabriele A1 - Lentzen, G. A1 - Seitz, H. A1 - Rampp, M. A1 - Schuster, S.C. A1 - Klenk, H.-P. A1 - Pfeiffer, F. A1 - Oesterheit, D. A1 - Kunte, Hans-Jörg T1 - A blueprint of ectoine metabolism from the genome of the industrial producer Halomonas elongata DSM 2581T N2 - The halophilic γ-proteobacterium Halomonas elongata DSM 2581T thrives at high salinity by synthesizing and accumulating the compatible solute ectoine. Ectoine levels are highly regulated according to external salt levels but the overall picture of its metabolism and control is not well understood. Apart from its critical role in cell adaptation to halophilic environments, ectoine can be used as a stabilizer for enzymes and as a cell protectant in skin and health care applications and is thus produced annually on a scale of tons in an industrial process using H. elongata as producer strain. This paper presents the complete genome sequence of H. elongata (4 061 296 bp) and includes experiments and analysis identifying and characterizing the entire ectoine metabolism, including a newly discovered pathway for ectoine degradation and its cyclic connection to ectoine synthesis. The degradation of ectoine (doe) proceeds via hydrolysis of ectoine (DoeA) to Nα-acetyl-L-2,4-diaminobutyric acid, followed by deacetylation to diaminobutyric acid (DoeB). In H. elongata, diaminobutyric acid can either flow off to aspartate or re-enter the ectoine synthesis pathway, forming a cycle of ectoine synthesis and degradation. Genome comparison revealed that the ectoine degradation pathway exists predominantly in non-halophilic bacteria unable to synthesize ectoine. Based on the resulting genetic and biochemical data, a metabolic flux model of ectoine metabolism was derived that can be used to understand the way H. elongata survives under varying salt stresses and that provides a basis for a model-driven improvement of industrial ectoine production. KW - Genom KW - Ectoin KW - Biotechnologie KW - Halophile Bakterien PY - 2011 DO - https://doi.org/10.1111/j.1462-2920.2010.02336.x SN - 1462-2912 SN - 1462-2920 VL - 13 IS - 8 SP - 1973 EP - 1994 PB - Blackwell Science CY - Oxford AN - OPUS4-22344 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ruedrich, J. A1 - Rieffel, Y. A1 - Pirskawetz, Stephan A1 - Alpermann, H. A1 - Joksch, U. A1 - Gengnagel, C. A1 - Weise, Frank A1 - Plagge, R. A1 - Zhao, J. A1 - Siegesmund, S. T1 - Development and assessment of protective winter covers for marble statuaries of the Schlossbrücke, Berlin (Germany) N2 - The present study documents the results of an inter-disciplinary model project that was planned with the aim of developing an innovative winter covering system for marble statuaries located on the Schlossbru¨cke (Berlin). Such a system would need to fulfil the various requirements for structural stability, aesthetics, climate and practical use. This applied research represents the first complex scientific study of the sustainability of a winter covering system. The study is characterised by the use of complex scientific instruments such as special laboratory analysis and numerical simulation tools. The interaction between the environment and the artefacts in connection with the innovative winter covering structures were studied by extensive climatic monitoring. KW - Marble sculptures KW - Marble weathering KW - Winter cover KW - Climate data KW - Numerical simulations PY - 2011 DO - https://doi.org/10.1007/s12665-010-0765-2 SN - 1866-6280 SN - 1866-6299 VL - 63 IS - 7-8 SP - 1823 EP - 1848 PB - Springer CY - Berlin; Heidelberg AN - OPUS4-22363 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Körner, Ursula A1 - Neitsch, Marcel A1 - Wytrykus, Nancy A1 - Kiau, Torsten A1 - Schuster, Raimund T1 - Der schnelle Weg zur Zulassung N2 - Ein neues Schema der Bundesanstalt für Materialforschung und -prüfung vereinfacht das Abrufen von Informationen zur Zulassung und Anerkennung von Qualitätssicherungsprogrammen durch direkte Verlinkungen. KW - Gefahrgut KW - Verpackung KW - IBC KW - Zulassung KW - BAM-GGR 001 KW - Qualitätssicherungsprogramm KW - Wiederaufarbeitung PY - 2011 SN - 0944-6117 IS - 1 SP - 28 EP - 31 PB - Vogel CY - München AN - OPUS4-22775 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn A1 - Krüger, Jörg A1 - Rohloff, M. A1 - Das, S. K. A1 - Höhm, S. A1 - Rosenfeld, A. T1 - Femtosecond laser-induced periodic surface structures: importance of transient excitation stages T2 - SPIE Conference on Optics+Optoelktronics 2011, Conference "Damage to VUV, EUV and X-ray Optics (XDAM3)" CY - Prague, Czech Republic DA - 2011-04-18 PY - 2011 AN - OPUS4-23549 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan A1 - Lippitz, Judith A1 - Kraft, Benedikt A1 - Rackwitz, Vanessa A1 - Terborg, R. T1 - Performance check of EDS X-ray spectrometers; extension to high count rates T2 - EMAS 2011, 12th european workshop on modern developments and applications in microbeam analysis CY - Angers, France DA - 2011-05-15 PY - 2011 AN - OPUS4-23550 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Procop, M. A1 - Kemf, N. A1 - Hahn, M. A1 - Hodoroaba, Vasile-Dan T1 - Investigation of the enrichment of Co and Cr in periprostethic tissue by scanning electron microscopy and spatial resolved x-ray fluorescence spectroscopy after total hip resurfacing arthroplasty T2 - EMAS 2011, 12th European Workshop on Modern Developments and Applications in Microbeam Analysis CY - Angers, France DA - 2011-05-15 PY - 2011 AN - OPUS4-23551 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Procop, M. A1 - Kemf, N. A1 - Hahn, M. A1 - Hodoroaba, Vasile-Dan T1 - Investigation of the enrichment of Co and Cr in periprostethic tissue by scanning electron microscopy and spatial resolved x-ray fluorescence spectroscopy after total hip resurfacing arthroplasty T2 - EMAS 2011, 12th European Workshop on Modern Developments and Applications in Microbeam Analysis CY - Angers, France DA - 2011-05-15 PY - 2011 AN - OPUS4-23552 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Heinrich, Sebastian A1 - Plettig, M. A1 - Klemm, E. T1 - Role of the Ti(IV)-superoxide species in the selective oxidation of alkanes with hydrogen peroxide in the gas phase on titanium silicalite-1: an in situ EPR investigation N2 - The interaction of TS-1 with gaseous hydrogen peroxide at temperatures above 373 K has been investigated by in situ EPR measurements. Treatment of TS-1 with hydrogen peroxide in the gas phase leads to a strong EPR signal, assigned to the Ti(IV)-superoxide species. In contrast to investigations with liquid hydrogen peroxide, here only one Ti(IV)-superoxide species could be detected in the EPR spectrum. The time constant of the reaction of the Ti(IV)-superoxide species detected by in situ EPR measurements was much larger than that observed for the rate of consumption of propane or propene via gas chromatographic analysis. Thus, we conclude that the Superoxide species may take part in the oxidation reaction (via side reactions or the formation of unselective products), but is probably not the main responsible species in the oxidation of propane or propene. KW - Titanium silicalite-1 KW - EPR KW - Oxidation KW - Hydrogen peroxide KW - Superoxide KW - Alkanes PY - 2011 DO - https://doi.org/10.1007/s10562-010-0534-6 SN - 1011-372X VL - 141 IS - 2 SP - 251 EP - 258 PB - Kluwer CY - Dordrecht AN - OPUS4-23553 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dietrich, Paul A1 - Horlacher, T. A1 - Girard-Lauriault, Pierre-Luc A1 - Gross, Thomas A1 - Lippitz, Andreas A1 - Min, Hyegeun A1 - Wirth, Thomas A1 - Castelli, R. A1 - Seeberger, P.H. A1 - Unger, Wolfgang T1 - Adlayers of dimannoside thiols on gold: surface chemical analysis N2 - Carbohydrate films on gold based on dimannoside thiols (DMT) were prepared, and a complementary surface chemical analysis was performed in detail by X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (ToF-SIMS), near-edge X-ray absorption fine structure (NEXAFS), FT-IR, and contact angle measurements in order to verify formation of ω-carbohydrate-functionalized alkylthiol films. XPS (C 1s, O 1s, and S 2p) reveals information on carbohydrate specific alkoxy (C–O) and acetal moieties (O–C–O) as well as thiolate species attached to gold. Angle-resolved synchrotron XPS was used for chemical speciation at ultimate surface sensitivity. Angle-resolved XPS analysis suggests the presence of an excess top layer composed of unbound sulfur components combined with alkyl moieties. Further support for DMT attachment on Au is given by ToF-SIMS and FT-IR analysis. Carbon and oxygen K-edge NEXAFS spectra were interpreted by applying the building block model supported by comparison to data of 1-undecanethiol, poly(vinyl alcohol), and polyoxymethylene. No linear dichroism effect was observed in the angle-resolved C K-edge NEXAFS. KW - Carbohydrates KW - Self-assembled monolayer KW - XPS KW - NEXAFS KW - ToF-SIMS KW - Surface chemical analysis PY - 2011 DO - https://doi.org/10.1021/la104038q SN - 0743-7463 SN - 1520-5827 VL - 27 IS - 8 SP - 4808 EP - 4815 PB - American Chemical Society CY - Washington, DC AN - OPUS4-23554 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schurig, Michael A1 - Reich, Franziska A1 - Jochems, Frank A1 - Klinger, Christian T1 - Vibrationsprüfungen an sicherheitskritischen Ventilen, zwei Beispiele aus Forschung und Anwendung T2 - 40. Jahrestag der Gesellschaft für Umweltsimulation (GUS) e.V. CY - Karlsruhe, Germany DA - 2011-03-30 PY - 2011 AN - OPUS4-23556 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brás, A.R. A1 - Merino, E.G. A1 - Neves, P.D. A1 - Fonseca, I.M. A1 - Dionísio, M. A1 - Schönhals, Andreas A1 - Correia, N.T. T1 - Amorphous ibuprofen confined in nanostructured silica materials: a dynamical approach N2 - The molecular mobility of condensed matter confined to nanometer dimensions can be dramatically changed from those of the bulk state in such a way that, when the guest is a drug, it can be advantageously used in pharmaceutical applications. We show by dielectric relaxation spectroscopy that the molecular mobility of the important ibuprofen drug embedded in nanoporous SBA-15 is significantly influenced by the confinement. An evidence of the existence of two families of molecules with different molecular mobilities is provided and investigated in their temperature dependence. One family is due to molecules close to the pores' center with a higher mobility compared with the bulk at low temperatures, and another family with slower dynamics originated from molecules interacting with the pore walls. The work reports the simultaneous manifestation of true confinement and surface effects in this nanostructured silica host for a drug. For future applications in drug delivery systems, the dynamics determined by the guest–host interplay and the one of the bulklike molecules can be tuned to achieve a desired release profile. PY - 2011 DO - https://doi.org/10.1021/jp107631m SN - 1932-7447 SN - 1089-5639 VL - 115 IS - 11 SP - 4616 EP - 4623 PB - Soc. CY - Washington, DC AN - OPUS4-23518 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schwenk, Christopher A1 - Tikhomirov, D. A1 - Eßer, G. A1 - Rethmeier, Michael T1 - General standard for welding simulation N2 - For differentiating the applicability of various numerical welding Simulation methods as well as unifying the prerequisites and the Steps to be taken in Simulation, normative codes are required for the user. Since any standard-like documents are currently still lacking in this field, DIN German Institute for Standardization has set up the Standards Committee NA 092-00-29-AA "Welding Simulation" dealing with the preparation of respective documents. This committee was initiated in partnership with the joint committee FA 12 "Weld Simulation on Application" of the Research Association of DVS German Welding Society. The objective of this Standardization work in the field of numerical welding Simulation is to prepare a DIN SPEC with a view to standardizing the approaches to the Simulation of various welding phenomena and processes over the long run. In a draft version of DIN SPEC 32534 that has already been prepared by the above mentioned Committee, the structure of the primary document was stated. The primary document specifies the application fields and the key terms of welding Simulation. In addition, the generally valid Simulation structure has been established which is intended to serve as a recommendation for customers and suppliers in formulating and handling a Service order as well as for persons who Start doing welding Simulation for the first time. This article focuses on the presentation of the new DIN SPEC 32534-1 explaining the major Simulation Steps. It additionally addresses the Classification of the secondary documents depending on the welding process and on the desired Simulation result. Finally, it gives an overview of the other subject areas dealt with in the Standards Committee NA 092-00-29-AA "Welding Simulation" as well as of the international activities in this field. T2 - IIW SC-Auto Intermediate Meeting CY - Ijmuiden, The Netherlands DA - 11.04.2011 KW - Welding simulation KW - Standardization KW - Applicability KW - Execution KW - Result display PY - 2011 IS - SC-Auto-44-11 SP - 1 EP - 10 AN - OPUS4-23519 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Waltraut A1 - Koynov, K. A1 - Pierrat, S. A1 - Thiermann, Raphael A1 - Fischer, K. A1 - Maskos, Michael T1 - pH-change protective PB-b-PEO polymersomes N2 - Poly(butadiene)-b-poly(ethylene oxide) vesicles were successfully loaded with hydrophilic dye Phloxine B. Dye addition during vesicle formation leads to Phloxine B encapsulated inside the water filled vesicle core as well as to freely diffusing dye molecules. The removal of uncapsulated substrate involves time consuming methods like dialysis or harsher methods like ultra filtration or selective precipitation, posing the risk of irreversible sample manipulation. Here used Phloxine B as pH sensitive fluorescence indicator allows the characterization of hydrophilic loading without separation procedure by adjusting the pH value. Additionally membrane blocking efficiency can be studied by time dependent fluorescence measurements. Cryogenic TEM studies showed that the self-assembled structure remained unchanged when the hydrophilic dye was incorporated within the vesicles. Fluorescence microscopy imaging proved the encapsulation of the hydrophilic dye inside the core volume. The combination of fluorescence correlation spectroscopy (FCS) and dynamic light scattering (DLS) measurements as ensemble methods confirmed those results additionally. KW - Diblock copolymers KW - Self assembly KW - Vesicle loading PY - 2011 DO - https://doi.org/10.1016/j.polymer.2011.01.028 SN - 0032-3861 SN - 1873-2291 VL - 52 IS - 5 SP - 1263 EP - 1267 PB - Elsevier Ltd. AN - OPUS4-23520 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Poli, Marco A1 - Scheider, Swen A1 - Arndt, Detlef A1 - Grätz, Rainer A1 - Schröder, Volkmar T1 - Auswirkungen von Turbulenzen auf die Druckentlastung von Gasexplosionen N2 - Zur Bemessung von Druckentlastungseinrichtungen bei Gasexplosionen in Umschließungen existieren derzeitig nur wenige wissenschaftlich fundierte Auslegungskriterien, die die konstruktiven Randbedingungen oder Prozessbedingungen der explosionsgefährdeten Anlagenteile ausreichend berücksichtigen. Aus diesem Grund werden in der Praxis häufig stark konservative Annahmen getroffen, die zu erheblichen Überdimensionierungen der Druckentlastungseinrichtungen führen können. Aus sicherheitstechnischer Perspektive können gerade diese vermeintlichen Sicherheitsmargen zu einer erheblichen Beschleunigung des transienten Druckverlaufs und damit eher zu einer Unterdimensionierung führen oder sogar den Übergang von Deflagrationen zu Detonationen begünstigen. Sowohl Messungen als auch erste Simulationen mit Hilfe von CFD-Modellen begründen die Notwendigkeit weiterer Untersuchungen mit explosionsgefährdeten Gasanlagen. Da insbesondere bei turbulenten Verbrennungsvorgängen in den Normen Verbesserungspotential herrscht, wird bei der BAM zukünftig verstärkt dieses Thema in Forschungsarbeiten berücksichtigt. KW - Explosionsschutz KW - Druckentlastung KW - Turbulenz PY - 2011 SN - 0030-834X VL - 121 IS - 1 SP - 51 EP - 54 PB - Wirtschaftsverl. NW CY - Bremerhaven AN - OPUS4-23521 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gebhard, St. A1 - König, J. A1 - Reichelt, Manuel A1 - Spaltmann, Dirk T1 - Maintenance and repair of railway wheels T2 - MRO-Konferenz (Fraunhofer Innovationscluster) CY - Berlin, Germany DA - 2011-03-25 PY - 2011 AN - OPUS4-23522 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Isecke, Bernd T1 - Systemspezifische Normen zum Korrosionsschutz von Metallen T2 - OTTI Fachforum Metallkorrosion - eine vermeidbare Materialzerstörung! CY - Regensburg, Germany DA - 2011-04-06 PY - 2011 AN - OPUS4-23523 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Isecke, Bernd T1 - Grundlagen der Korrosion und des Korrosionsschutzes T2 - OTTI Fachforum Metallkorrosion - eine vermeidbare Materialzerstörung! CY - Regensburg, Germany DA - 2011-04-06 PY - 2011 AN - OPUS4-23524 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Isecke, Bernd T1 - Wirtschaftliche Aspekte des Korrosionsschutzes T2 - OTTI Fachforum Metallkorrosion - eine vermeidbare Materialzerstörung! CY - Regensburg, Germany DA - 2011-04-06 PY - 2011 AN - OPUS4-23525 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Siegel, David A1 - Babuscio, T. T1 - Mycotoxin management in the European cereal trading sector N2 - On the world scale, the European Union has established the most comprehensive regulations for mycotoxins in food and feed. These regulations, which areinter alia expressed in the form of maximum levels, largely affect cereal traders. To ensure the safety of their products and compliance with EU legislation traders are required to quantify the mycotoxin levels in their lots. However, while the analytical approaches of research and enforcement are well known and frequently reviewed in the scientific and legal literature, little detailed information is available on the mycotoxin management concepts of trade. The present article is intended to close this gap. On the basis of the results of two surveys conducted amongst European cereal traders in the years 2007 and 2009, three key issues in commercial mycotoxin management are outlined and discussed in the context of the current scientific literature. These are: the issue of sampling, the availability and performance of suitable analytical methods as well as issues evolving from variations between regulatory and contractual maximum levels. KW - Mycotoxins KW - Cereals KW - Trading KW - Analysis KW - Food safety PY - 2011 DO - https://doi.org/10.1016/j.foodcont.2011.02.022 SN - 0956-7135 VL - 22 IS - 8 SP - 1145 EP - 1153 PB - Elsevier CY - Amsterdam AN - OPUS4-23526 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute A1 - Grabolle, Markus A1 - Behnke, Thomas A1 - Würth, Christian A1 - Hoffmann, Katrin A1 - Pauli, Jutta A1 - Brehm, Robert T1 - Functional Chromophores, Method development and fluorescence standards for fluorescence-based Bioanalysis T2 - TU Berlin, Fachbereich Pysik AK Prof. Hoffmann CY - Berlin, Germany DA - 2011-01-03 PY - 2011 AN - OPUS4-23527 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nai, Corrado A1 - Pannenbecker, Annette Cecilia A1 - Noack-Schönmann, Steffi A1 - Broughton, William J. A1 - Gorbushina, Anna T1 - Growth physiology of Sarcinomyces petricola A95, a model black fungus to study primary successions in terrestrial ecosystems and subaerial biofilms T2 - Annual Conference of the Association for General and Applied Microbiology (VAAM) CY - Karlsruhe, Germany DA - 2011-04-03 PY - 2011 N1 - Geburtsname von Noack-Schönmann, Steffi: Noack, S. - Birth name of Noack-Schönmann, Steffi: Noack, S. AN - OPUS4-23508 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neitsch, Marcel T1 - Aus der Praxis für die Praxis: Überwachungsprüfung T2 - Informationsaustausch Qualitätssicherung und Überwachung bei der Herstellung von Gefahrgutverpackungen - Metall (INQÜ), BAM CY - Berlin, Germany DA - 2011-03-23 PY - 2011 AN - OPUS4-23509 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Woydt, Mathias T1 - Non-fossil fuel scenario (Fortsetzung HLEG 14) T2 - High-Level-Experten-Treffen: "Idealer Flughafen der Zukunft 15" CY - Berlin, Germany DA - 2011-04-08 PY - 2011 AN - OPUS4-23510 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Denkler, Tilman T1 - Quality Infrastructure and Accreditation in Germany N2 - - Definition of Quality Infrastructure - Accreditation of certification bodies - Tasks of BAM in the area of Quality Infrastructure - Accreditation procedures, examples T2 - Workshop zur Qualitätsinfrastruktur und Akkreditierung in Deutschland im Rahmens des International Training Programme on "Certification for aggricultural commodities and accreditationfor certifying bodies" CY - Berlin, Germany DA - 2011-03-28 PY - 2011 AN - OPUS4-23513 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lahcini, M. A1 - Qayouh, H. A1 - Yashiro, T. A1 - Weidner, Steffen A1 - Kricheldorf, H.R. T1 - Bismuth-triflate-catalyzed polymerizations of epsilon-caprolactone N2 - εCL was polymerized using the triflates of lanthanum, samarium, magnesium, aluminum, scandium, and bismuth as catalysts. Bismuth triflate proved to be extraordinarily reactive, and catalyzed polymerizations of εCL even at 20 °C. Adding DTBMP reduced the polymerization rate only slightly. Furthermore, no evidence of a cationic mechanism was found by end‐group analyses. Polymerization at 20 °C either in bulk or in solution only yielded polyesters of low or medium molecular weights. Yet addition of alcohols allowed for a proper control of molecular weight and end‐groups. Additionally, low catalyst concentrations and low temperature resulted in narrow molecular weight distributions and polylactones almost free of cyclic compounds. KW - Bismuth KW - Epsilon-caprolactone KW - Ring-opening polymerization KW - Telechelic polyesters PY - 2011 DO - https://doi.org/10.1002/macp.201000517 SN - 1022-1352 SN - 1521-3935 VL - 212 IS - 6 SP - 583 EP - 591 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-23514 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brandes, E. A1 - Hieronymus, Hartmut T1 - Sicherheit bei mikrostrukturierten Reaktoren - Ergebnisse und Schlussfolgerungen aus Untersuchungen am Beispiel von Ethan/Sauerstoff-, Ethen/Sauerstoff- und Ethen/Lachgas-Gemischen N2 - Die Mikroverfahrenstechnik (typische innere Abmessungen der Apparaturen < 1000 pin) erfährt zunehmend Interesse für industrielle Anwendungen. Grund hierfür sind verschiedene Vorteile gegenüber konventionellen chemischen. Reaktoren wie ein erhöhter Wärme- und Stofftransport und größere spezifische Phasengrenzen. Hierdurch können im Zuge einer Prozessintensivierung höhere Raum-Zeil-Ausbeuten und Selektivitäten und darüber hinaus eine sicherere Prozessführung erreicht werden. Dies trifft vor allem dann zu, wenn als Oxidationsmittel reiner Sauerstoff, Distickstoffmonoxid (Lachgas) oder ähnliche Substanzen mit hohem Oxidationspotential eingesetzt werden. Vielfach wird angenommen, dass Mikroreaktoren inhärent sicher gegenüber Deflagrations- und Detonationsvorgängen sind. Durchmesser der Reaktionskanäle von 0,5 nun und kleiner lassen Flammendurchschläge zumindest bei Stoffen der Explosionsgruppen I1A und TIB für Gemische mit Luft als Oxidationsmittel und Umgebungsbedingungen (ca. 20 °C, ca. 1.013 mbar) als ausgeschlossen erscheinen. Für die in der Mikroverfahrenstechnik bevorzugten Reaktionsbedingungen wie erhöhter Druck, erhöhte Temperatur und vor allem Oxidationsmittel mit erhöhtem Oxidalionspotential gilt dies jedoch nicht. KW - Mikroreaktor KW - Explosion KW - Detonation KW - Oxidation PY - 2011 SN - 0030-834X VL - 121 IS - 1 SP - 55 EP - 58 PB - Wirtschaftsverl. NW CY - Bremerhaven AN - OPUS4-23515 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Maierhofer, Christiane A1 - Krankenhagen, Rainer A1 - Röllig, Mathias A1 - Mecke, R. A1 - Schiller, M. A1 - Seidl, T. A1 - Kalisch, U. A1 - Hennen, C. A1 - Meinhardt, J. T1 - Bewertung von Schäden an historischen Bauteilen mit aktiver Thermografie und 3D-Laserscanner N2 - Sowohl in der Denkmalpflege als auch in anderen Anwendungsbereichen der zerstörungsfreien Prüfung können größere kostenintensive Erhaltungs- und Instandsetzungsmaßnahmen durch das frühzeitige Erkennen und Einschätzen von Schäden vermieden werden. Eine derartige vorbeugende Instandsetzung ist jedoch nur möglich, wenn häufige Inspektionen kostengünstig und schnell durchgeführt werden können. Systematische Methoden zur Beobachtung und Erfassung von Prozessen über einen längeren Zeitraum sowie deren Überwachung werden unter dem Begriff "Monitoring" zusammengefasst. KW - Aktive Thermografie KW - 3D-Laserscanner KW - Monitoring KW - Historische Bauteile KW - Datenfusion PY - 2011 IS - Februar SP - 51 EP - 56 PB - Ernst & Sohn CY - Berlin AN - OPUS4-23516 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schwenk, Christopher T1 - Developing guidelines for numerical welding simulation N2 - A goal of industry is to fully map the fabrication process — from the blank metal through the individual fabrication steps all the way to the end product — in a so-called "virtual process chain." The concept of continuous simulation of all relevant fabrication segments is intended not only to achieve a reduction in development and fabrication costs, but most of all to optimize products and fabrication procedures. An essential link in this virtual process chain is welding simulation. PY - 2011 SN - 0043-2296 SN - 0096-7629 IS - April SP - 49 EP - 51 PB - American Welding Society CY - New York, NY AN - OPUS4-23517 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas A1 - Maierhofer, Christiane T1 - Verbesserung der zerstörungsfreien Prüfung vor Ort durch den Einsatz bildgebender Verfahren T2 - Wissenschaft trifft Handwerk CY - Leipzig, Germany DA - 2011-03-15 PY - 2011 AN - OPUS4-23498 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Gablenz, C.-H. A1 - Spaltmann, Dirk ED - Horn, P. T1 - Das CargoLifter Ballonkransystem - der 'CargoLifter Lufthaken' ist da! N2 - Das CargoLifter Ballonkransystem nutzt die Prinzipien der Leichter-als-Luft-Technologie für das Heben von Gütern. Der mit leichtem Gas gefüllte Ballon drängt in der schwereren Luft nach oben und kann somit Lasten anheben. Im Gegensatz zu erdgebundenen Kränen ist für den Luftkran die Beschaffenheit des Bodens sekundär. Der Ballonkran wird an drei Winden verankert und über die im Kranknotenpunkt zusammengeführten Seile präzise gesteuert. Beim Heben und Versetzen verbleibt die Last unter dem Ballon, der stets 100% seiner Hubkraft auch bis zu 200m Höhe und selbst weiterem Versatz behält. Reichweite bedeutet beim CargoLifter Ballonkransystem statt mehr Ausleger mehr Seil. T2 - 19. Internationale Kranfachtagung 2011 - Der Kran und sein Umfeld in Industrie und Logistik CY - Magdeburg, Deutschland DA - 31.03.2011 PY - 2011 SN - 978-3-930385-74-4 SP - 11 EP - 22 CY - Magdeburg AN - OPUS4-23499 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völz, Uwe A1 - Dugan, S. A1 - Walte, F. T1 - Further Development of NDT-Methods Applicable on Thick-walles Ni-based Components T2 - 4th Workshop COMTES700 CY - Essen, Germany DA - 2011-04-11 PY - 2011 AN - OPUS4-23500 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völz, Uwe T1 - Visualisierung der Schallausbreitung in Festkörpern mit elektrodynamischen Sonden T2 - DAGA CY - Düsseldorf, Germany DA - 2011-03-21 PY - 2011 AN - OPUS4-23501 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lischka, Susanne A1 - Nehls, Irene A1 - Piechotta, Christian T1 - 13C-markierte Kalibrierstandards für die Arsenspeziesanalytik mittels LC-ESI-MS/MS T2 - Berliner Chemie Symposium (Jungchemikerforum) der Humboldt-Universität Berlin CY - Berlin, Germany DA - 2011-04-07 PY - 2011 AN - OPUS4-23504 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koch, Matthias A1 - Proske, Matthias A1 - Siegel, David A1 - Riedel, Juliane A1 - Sauer, Andreas A1 - Nehls, Irene T1 - Zearalenone in edible oil - a method comparison study T2 - 33. Mykotoxin-Workshop der Gesellschaft für Mykotoxinforschung e. V. CY - Freising, Germany DA - 2011-05-30 PY - 2011 N1 - Geburtsname von Sauer, Andreas: Buchholz, A. - Birth name of Sauer, Andreas: Buchholz, A. AN - OPUS4-23506 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Noack-Schönmann, Steffi A1 - Broughton, William J. A1 - Nai, Corrado A1 - Schneider, Lucienn A1 - Banasiak, Ronald A1 - Gorbushina, Anna T1 - Genetic Characterisation of MCF A95, a Micro-colonial Fungus that colonises Bare Rocks T2 - Annual Conference of the Association for General and Applied Microbiology (VAAM) CY - Karlsruhe, Germany DA - 2011-04-03 PY - 2011 N1 - Geburtsname von Noack-Schönmann, Steffi: Noack, S. - Birth name of Noack-Schönmann, Steffi: Noack, S. AN - OPUS4-23507 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute A1 - Würth, Christian A1 - Grabolle, Markus A1 - Pauli, Jutta A1 - Lochmann, Cornelia A1 - Spieles, Monika T1 - Methods for the Determination of the Fluorometric Key Parameter Photoluminescence Quantum Yield - Relative and Absolute Measurement and Achievable Uncertainties T2 - TU Berlin, Fachbereich Pysik AK Prof. Hoffmann CY - Berlin, Germany DA - 2011-03-01 PY - 2011 AN - OPUS4-23528 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hennig, Andreas A1 - Resch-Genger, Ute A1 - Sloniec, Jagoda T1 - Flourescent Denivatives of Cryptophan-A: Biomembrane Interactions of Potential Multimodal Contrast Agents T2 - FMP Berlin Leibniz-Institut for Molecular CY - Berlin, Germany DA - 2011-02-15 PY - 2011 AN - OPUS4-23529 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hennig, Andreas A1 - Resch-Genger, Ute A1 - Sloniec, Jagoda T1 - A FRET-Based Method to probe biomembrane interactions of multimodal contrast Agents T2 - International Bunsen Discussion meeting on Förster Resonance Energy Transfer in the Life Sciences CY - Göttingen, Germany DA - 2011-03-27 PY - 2011 AN - OPUS4-23530 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute A1 - Grabolle, Markus A1 - Behnke, Thomas A1 - Würth, Christian A1 - Hoffmann, Katrin A1 - Pauli, Jutta A1 - Brehm, Robert T1 - Functional Chromophores, Method development and fluorescence standards for fluorescence-based Bioanalysis T2 - eingeladener Vortrag FU Berlin CY - Berlin, Germany DA - 2011-02-08 PY - 2011 AN - OPUS4-23531 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rauchegger, Christian A1 - Schalau, Bernd A1 - Schmidt, Dirk A1 - Lohse, Volkmar A1 - Schröder, Volkmar A1 - Thévenin, D. T1 - Experimental results from heavy gas dispersions (R134a) N2 - Heavy gases in large quantities are used worldwide in various industries. Past incidents, such as the liquefied gas disaster in Viareggio (2009) have shown that these materials are difficult to handle in a safe manner. According to the German Hazardous Incident Ordinance (StörfallVO 2000 - 12. BIMSchV), plant operators with extended responsibilities must produce a report in which they verify that , in the event of an unintentional gas release, the surrounding area will not be aversely affected. Essential elements of this report are calculations of both the released mass flow and the gas dispersion. Using models such as the VDI guideline 3783 (state of the art in Germany) plant operators are able to predict the characteristics of likely gas dispersions. The presented experimental investigations were carried out at the BAM better understand heavy gas dispersion with high gas concentrations in the air (≥ 1 Vol.-%), as well as concentrations with approximately neutral density characteristics (≤ 3000ppm) in order to test the accuracy of the VDI guideline. The starting point for experimental trials was the heavy gas releases resulting from pipeline, vessel or standard gas bottle leaks, with mass flows of between 20 and 100 g s-1. Investigations on the gas-phase release process focused on the unsteady mass flow associated with releases from standard gas bottles. The experimental results will be used as comparative parameters for future simulations. The goal of these simulations is to develop a model with which calculation of the unsteady mass flow, based on the material characteristics for any gas, is possible. T2 - 7th Global congress on process safety - 2011 Spring meeting CY - Chicago, Illinois, USA DA - 13.03.2011 KW - Heavy gas KW - Gas releases KW - Dispersion KW - Measurement KW - VDI guideline 3783 PY - 2011 SP - 1 EP - 12 AN - OPUS4-23532 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute A1 - Würth, Christian A1 - Grabolle, Markus A1 - Pauli, Jutta A1 - Lochmann, Cornelia A1 - Spieles, Monika T1 - Fluorometric methods for the measurement of photoluminescence quantum yields T2 - eingeladener Vortrag TU Berlin CY - Berlin, Germany DA - 2011-02-22 PY - 2011 AN - OPUS4-23533 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hoffmann, Katrin A1 - Behnke, Thomas A1 - Drescher, Daniela A1 - Kneipp, Janina A1 - Resch-Genger, Ute T1 - Lifetime-based Discrimination between Spectrally Matching vis and NIR Ermitting Particle Labels and Probes T2 - BIOS SPIE Photonics West 2011 CY - San Francisco, CA, USA DA - 2011-01-22 PY - 2011 AN - OPUS4-23534 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute A1 - Hennig, Andreas A1 - Hoffmann, Katrin A1 - Hoffmann, Angelika T1 - Simple Procedure for the Quantification of Surface Functionalities an Beads and Planar substrates T2 - Anakon 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23535 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Linck, Lena A1 - Resch-Genger, Ute A1 - Reiß, Edda A1 - Bier, Frank A1 - Sobek, Jens T1 - Optimization of fluorescence signals on rolling amplification-enhanced microarrays T2 - Dechema Tagung functional genomics CY - Frankfurt am Main, Germany DA - 2011-02-03 PY - 2011 AN - OPUS4-23536 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Würth, Christian A1 - Behnke, Thomas A1 - Lochmann, Cornelia A1 - Resch-Genger, Ute T1 - New integrating sphere setup for the measurement of absolute fluorescence quantum yields as well as measurements of emission, transmission, and reflectance T2 - Colloquium Optische Spektroskopie COSP 2011 CY - Berlin, Germany DA - 2011-03-21 PY - 2011 AN - OPUS4-23537 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grabolle, Markus A1 - Würth, Christian A1 - Pauli, Jutta A1 - Spieles, Monika A1 - Lochmann, Cornelia A1 - Hoffmann, Katrin A1 - Resch-Genger, Ute T1 - Fluorometric methods for the measurement of photoluminescence quantum yields T2 - Colloquium Optische Spektroskopie COSP 2011 CY - Berlin, Germany DA - 2011-03-21 PY - 2011 AN - OPUS4-23538 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eisenacher, Germar A1 - Scheidemann, Robert A1 - Neumann, Martin A1 - Sterthaus, Jens A1 - Kasparek, Eva Maria A1 - Völzke, Holger T1 - Stauchversuche mit querdehnungsbehinderten Fichtenholzproben verschiedener Faserorientierungen bei verändertlicher Dehnrate T2 - Kontec CY - Dresden, Germany DA - 2011-04-06 PY - 2011 AN - OPUS4-23539 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Würsig, Andreas A1 - Jochems, Frank T1 - Unterschiede zwischen UN- und RID/ADR-Landtanks T2 - IHK-Workshop CY - Braunschweig, Germany DA - 2011-04-14 PY - 2011 AN - OPUS4-23541 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker T1 - Lebensdauerabschätzung für Polypropylen durch Dosis-Wirkungsfunktionen bezüglich Bestrahlungsstärke und Temperatur (ViPQuali-Projekt) T2 - 40. Jahrestagung der GUS CY - Stutensee, Germany DA - 2011-03-28 PY - 2011 AN - OPUS4-23542 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weißhaupt, Petra A1 - Pritzkow, Wolfgang A1 - Noll, Matthias T1 - Nitrogen metabolism of wood decomposing basidiomycetes and their interaction with diazotrophs as revealed by IRMS T2 - Jahrestagung der Vereinigung für Allgemeine und Angewandte Mikrobiologie (VAAM) CY - Karlsruhe, Germany DA - 2011-04-03 PY - 2011 AN - OPUS4-23543 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herrmann, Bianca A1 - Plarre, Rüdiger T1 - Autökologische und molekularbiologische Untersuchungen zur Charakterisierung der Kleidermotte Tineola bisselliella (Lepidoptera: Tineidae) als Referenzorganismus T2 - DGaaE Entomologentagung CY - Berlin, Germany DA - 2011-03-21 PY - 2011 N1 - Geburtsname von Herrmann, Bianca: Krüger-Carstensen, B. - Birth name of Herrmann, Bianca: Krüger-Carstensen, B. AN - OPUS4-23544 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weiler, Christiane A1 - Ifland, Andrea A1 - Sigiel, Sandra A1 - Naumann, Annette A1 - Noll, Matthias T1 - Characterisation of the incorporation of Listeria monocytogenes in a raw milk-biofilm T2 - VAAM-Tagung CY - Karlsruhe, Germany DA - 2011-04-03 PY - 2011 AN - OPUS4-23545 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Darlatt, Erik A1 - Poppenberg, J. A1 - Richter, S. A1 - Traulsen, H.-H. A1 - Dzyuba, E. V. A1 - Sattler, D. A1 - Schalley, C. A. A1 - Unger, Wolfgang T1 - Characterization of a rotaxane toplayer stack formed by self-assembly and layer-by-layer deposition exploiting coordination chemistry T2 - Berliner Chemie Symposium 2011 CY - Berlin, Germany DA - 2011-04-07 PY - 2011 AN - OPUS4-23547 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubcová, Petra A1 - Rübner, Katrin A1 - Ramge, Peter T1 - New Lightweight Aggregates from Heterogeneous Construction and Demolition Waste for the Use in Lightweight Concrete T2 - European Coatings Congress, "Construction Chemicals" CY - Nuremberg, Germany DA - 2011-03-28 PY - 2011 AN - OPUS4-23558 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fontana, Patrick A1 - Müller, Urs A1 - Meng, Birgit A1 - Malaga, Katarina A1 - Lagerblad, B. T1 - Precast concrete facade elements with low embodied energy T2 - ENBRI Workshop "Reaching the Nearly Zero-Energy Goal for Buildings" CY - Borås, Sweden DA - 2011-05-04 PY - 2011 AN - OPUS4-23559 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna T1 - Gesteinsbesiedelnde Pilze als Modellorganismen T2 - Vortrag CY - Rostock, Germany DA - 2011-04-14 PY - 2011 AN - OPUS4-23560 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo A1 - Baeßler, Matthias A1 - Georgi, Steven A1 - Rücker, Werner T1 - Pore-pressure-induced Softening and Long-Term Behaviour of Offshore Pile Foundations T2 - Workshop "Gründungen von Offshore-Windenergieanlagen", TU Berlin CY - Berlin, Germany DA - 2011-03-22 PY - 2011 AN - OPUS4-23561 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bothe, Martin A1 - Khine, Y. A1 - Chaobin, H. A1 - Pretsch, Thorsten T1 - SPOSS-PU Triple-shape Properties and Actuation T2 - Synthesis and Integration Group Seminar, Institute of Materials Research and Engineering (IMRE) CY - Singapore DA - 2011-04-27 PY - 2011 AN - OPUS4-23562 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lischka, Susanne A1 - Nehls, Irene A1 - Piechotta, Christian T1 - Application of a 13C-lableled calibration standard for the analysis of arsenobetaine in fish using HPLC-ESI-MS/MS T2 - TraceSpec CY - Pau, France DA - 2011-05-18 PY - 2011 AN - OPUS4-23563 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kromm, Arne A1 - Kannengießer, Thomas A1 - Altenkirch, J. A1 - Gibmeier, J. A1 - Buslaps, T. A1 - Wanner, A. T1 - In-Situ EDXRD zur Eigenspannungsentwicklung beim Lichtborgenschweißen T2 - AWT Fachausschuss 13 Eigenspannungen, Arbeitsgemeinschaft Wärmebehandlung und Werksofftechnik e. V. CY - Karlsruhe, Germany DA - 2011-04-12 PY - 2011 AN - OPUS4-23564 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hatto, P. A1 - Gee, M. A1 - Griepentrog, Michael T1 - Technical standards for ensuring consistency, reliability and performance of vacuum coatings T2 - Technical Conference: Society of Vacuum Coaters (SVC) CY - Chicago, IL, USA DA - 2011-04-16 PY - 2011 AN - OPUS4-23565 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thater, Raphael A1 - Perret, William A1 - Schwenk, Christopher A1 - Alber, U. A1 - Rethmeier, Michael T1 - Different modeling approaches for efficient dirtortion calculation of an automotive assembly T2 - International Workshop on Thermal Forming and Welding Distortion CY - Bremen, Germany DA - 2011-04-06 PY - 2011 AN - OPUS4-23566 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan A1 - Marinenko, R. A1 - Small, J. T1 - CCQM-P130: A Joint NIST/BAM Pilot Study for ED- and WD-EPMA T2 - Surface Analysis Working Group (SAWG) Meeting, CCQM CY - Sèvres, France DA - 2011-04-12 PY - 2011 AN - OPUS4-23567 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wehrstedt, Klaus-Dieter T1 - Self-reactive Substances Type G - Candidates for Division 4.2 T2 - IGUS Energetic and Oxidising Substances (EOS) Working Groupe Meeting CY - Washington, D.C., USA DA - 2011-04-27 PY - 2011 AN - OPUS4-23578 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wehrstedt, Klaus-Dieter T1 - Burning tests on liquid and solid organic peroxides - organic peroxide storage regulations, Part 2: Germany/Europe T2 - IGUS Energetic and Oxidising Substances (EOS) Working Group Meeting CY - Washington, D.C., USA DA - 2011-04-27 PY - 2011 AN - OPUS4-23579 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Damm, David A1 - Goedecke, Thomas A1 - Pettelkau, Alexander A1 - Farahbakhsh, Mahin A1 - Daum, Werner A1 - Bartholmai, Matthias A1 - Hohendorf, Stefan T1 - Datenfluss-Szenario im Projekt SIGRID Untertitel: Sicherung von Gefahrguttransporten durch RFID-Tags mit Sensorfunktionalität und integrierter Datenbank-GEFAHRGUT-Information T2 - Messe SENSOR+TEST 2011 (Die Messtechnik-Messe) CY - Nuremberg, Germany DA - 2011-06-07 PY - 2011 AN - OPUS4-23583 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zur, Malte A1 - Otremba, Frank A1 - Körner, Ursula T1 - Maßnahmen zur Vermeidung der Ausbildung zündfähiger Gas/Luft-Gemische in Flugzeugfrachträumen und Entwicklungen eines Maindeck-Feuerlöschsystems T2 - LUFO-Workshop CY - Bremen, Germany DA - 2011-02-16 PY - 2011 AN - OPUS4-23584 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Brekow, Gerhard T1 - In-service inspection Atucha T2 - Meeting ARN, BAM, GRS, MPA Stuttgart CY - Buenos Aires, Argentina DA - 2011-03-15 PY - 2011 AN - OPUS4-23585 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Urs T1 - Lehmsteine und Lehmmörtel - Nachhaltige Bauprodukte auf dem Weg zur Stoffnorm T2 - 4. Mauerwerk Kalender-Tag CY - Dresden, Germany DA - 2011-03-29 PY - 2011 AN - OPUS4-23586 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Perret, William T1 - Application of numercial welding simulation in car body construction - possibilities and limits T2 - Automotive Circle International - Fügen im Karosseriebau 2011 CY - Bad Nauheim, Germany DA - 2011-04-12 PY - 2011 AN - OPUS4-23587 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Michael-Schulz, Heike A1 - Kebben, Jochen A1 - Gebauer, Marek T1 - IBC 31HA1 - Internal Thermal Impact of an Organic Peroxide T2 - IGUS Energetic and Oxidizing Substrances (EOS) Working Group Meeting CY - Washington, D.C., USA DA - 2011-04-27 PY - 2011 AN - OPUS4-23569 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Michael-Schulz, Heike A1 - Kebben, Jochen T1 - UN Number 1942 - Ammonium Nitrate T2 - IGUS Energetic and Oxidizierung Substances (EOS) Working Group Meeting CY - Washington, D.C., USA DA - 2011-04-27 PY - 2011 AN - OPUS4-23570 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wehrstedt, Klaus-Dieter A1 - Michael-Schulz, Heike T1 - Classification of 5-Aminotetrazole and its hydrate T2 - IGUS Energetic and Oxidizierung Substances (EOS) Working Group Meeting CY - Washington, D.C., USA DA - 2011-04-27 PY - 2011 AN - OPUS4-23571 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wehrstedt, Klaus-Dieter A1 - Mishra, Kirti Bhushan T1 - Safety considerations for organic peroxide fires T2 - IGUS Energetic and Oxidizierung Substances (EOS) Working Group Meeting CY - Washington, D.C., USA DA - 2011-04-27 PY - 2011 AN - OPUS4-23572 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Knorr, Annett A1 - Wirker, Ringo A1 - Antes, Jürgen T1 - Orts- und zeitaufgelöste Wärmestrommessung in einem mikrostrukturierten Fallfilmreaktor T2 - 19. Ulm-Freiberger Kalorimetrietage CY - Freiberg, Germany DA - 2011-03-16 PY - 2011 AN - OPUS4-23573 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin A1 - Lüth, Peter A1 - Scheid, Marc A1 - Böhme, Thilo T1 - Projektstatusbericht 03/2011: GSBL Datenbank "Bandbreiten von Stäuben" und Interlaboratory test 2011/11 "EN 15188:2007 - Self-ignition temperature" T2 - ProcessNet Arbeitsausschuss "Sicherheitstechnische Kenngrößen" CY - Frankfurt am Main, Germany DA - 2011-03-31 PY - 2011 AN - OPUS4-23574 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheid, Marc T1 - Übersichtsvortrag Staubexplosionsgefahren und Beispiele für Schutzmaßnahmen T2 - Vortrag beim Seminar "Brand- und Explosionsschutz" der Metall-Berufsgenossenschaften CY - Triefenstein, Germany DA - 2011-04-04 PY - 2011 AN - OPUS4-23575 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulte, Petra T1 - Classification and details of physical hazards in chapter 9 of the Safety Data Sheet T2 - European standard phrases catalogue for EU safety data sheets, BusinessEurope Working Group EuPhraC CY - Berlin, Germany DA - 2011-04-12 PY - 2011 AN - OPUS4-23576 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kasch, Thomas A1 - Brock, Thomas A1 - Binder, Christian T1 - Example for applying an IR-camera system at BAM Federal Institut for Materials Research and Testing T2 - Hannover Messe CY - Hanover, Germany DA - 2011-04-06 PY - 2011 AN - OPUS4-23577 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Orts Gil, Guillermo A1 - Natte, Kishore A1 - Drescher, Daniela A1 - Bresch, Harald A1 - Mantion, Alexandre A1 - Kneipp, J. A1 - Österle, Werner T1 - Characterisation of silica nanoparticles prior to in vitro studies: from primary particles to agglomerates N2 - The size, surface charge and agglomeration state of nanoparticles under physiological conditions are fundamental parameters to be determined prior to their application in toxicological studies. Although silica-based materials are among the most promising candidates for biomedical applications, more systematic studies concerning the characterisation before performing toxicological studies are necessary. This interest is based on the necessity to elucidate the mechanisms affecting its toxicity. We present here TEM, SAXS and SMPS as a combination of methods allowing an accurate determination of single nanoparticle sizes. For the commercial material, Ludox TM50 single particle sizes around 30 nm were found in solution. DLS measurements of single particles are rather affected by polydispersity and particles concentration but this technique is useful to monitor their agglomeration state. Here, the influence of nanoparticle concentration, ionic strength (IS), pH and bath sonication on the agglomeration behaviour of silica particles in solution has been systematically investigated. Moreover, the colloidal stability of silica particles in the presence of BSA has been investigated showing a correlation between silica and protein concentrations and the formation of agglomerates. Finally, the colloidal stability of silica particles in standard cell culture medium has been tested, concluding the necessity of surface modification in order to preserve silica as primary particles in the presence of serum. The results presented here have major implications on toxicity investigations because silica agglomeration will change the probability and uptake mechanisms and thereby may affect toxicity. KW - Silica KW - Toxicology KW - Agglomeration KW - BSA KW - Nanoparticles KW - Characterisation PY - 2011 DO - https://doi.org/10.1007/s11051-010-9910-9 SN - 1388-0764 SN - 1572-896X VL - 13 IS - 4 SP - 1593 EP - 1604 PB - Springer AN - OPUS4-21179 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beck, Uwe A1 - Stephanowitz, Ralph A1 - Hertwig, Andreas A1 - Hönig, D. A1 - Schneider, S. A1 - Domnick, R. A1 - Belzner, M. T1 - Fabry-Perot Based Laser Systems with Embedded Public, Hidden, and Forensic Information For Anti-counterfeiting Applications T2 - International Conference on Metallurgical Coatings and Thin Films (ICMCTF) CY - San Diego, CA, USA DA - 2011-05-02 PY - 2011 AN - OPUS4-22094 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn A1 - Mermillod-Blondin, A. A1 - Mauclair, C. A1 - Rosenfeld, A. A1 - Stoian, R. A1 - Audouard, E. T1 - Time-resolved imaging of bulk a-SiO2 upon various ultrashort excitation sequences T2 - SPIE Photonics West Conference: Frontiers in Ultrafast Optics: Biomedical, Scientific and Industrial Applications XI (Conference 7925) CY - San Francisco, CA, USA DA - 2011-01-22 PY - 2011 AN - OPUS4-22095 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute A1 - Pauli, Jutta A1 - Behnke, Thomas A1 - Brehm, Robert A1 - Grabolle, Markus A1 - Hoffmann, Katrin A1 - Würth, Christian A1 - Mathejczyk, J. A1 - Alves, F. A1 - Hamann, J. A1 - Hilger, I. T1 - Dye-Biomolecule Conjugates and NIR-Fluorescent Particles for Targeting of Disease-related Biomarkers T2 - Eingeladener Vortrag SPIE Photonics West CY - San Francisco, CA, USA DA - 2011-01-22 PY - 2011 AN - OPUS4-22077 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Emmerling, Franziska T1 - In-situ Untersuchungen von Nukleations-, Kristallisations- und Wachstumsprozessen mit Synchrotronstrahlung T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-22564 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dabah, Eitan A1 - Kannengießer, Thomas A1 - Eliezer, D. A1 - Böllinghaus, Thomas T1 - In situ analysis of hydrogen behaviour in stainless steels by high energy synchrotron radiation N2 - Hydrogen generally causes lattice distortions and phase transformations when introduced into a metal matrix. The present contribution provides a report of first in situ investigations of hydrogen effects on the lattice of the austenite and the martensite phase in a supermartensitic stainless steel using hard synchrotron radiation for respective energy dispersion diffraction measurements. Lattice distortions, such as the planar spacing expansion, have been monitored during the complete hydrogen effusion process over 24 h and are directly correlated to the dissolved hydrogen in the metal matrix. Among other results, it turned out that hydrogen at the introduced concentration level causes a reversible lattice expansion and after hydrogen effusion the lattice nearly regained its original dimensions. Hydrogen much more significantly affects the austenite phase with respect to lattice expansion than the martensite phase, but no phase transformations occur during the hydrogen desorption process. KW - Hydrogen diffusion KW - Solubility KW - Lattice distortions KW - Energy dispersive X-ray diffraction PY - 2011 DO - https://doi.org/10.1016/j.msea.2010.10.090 SN - 0921-5093 SN - 1873-4936 VL - 528 IS - 3 SP - 1608 EP - 1614 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-22849 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit ED - Raupach, M. T1 - Einfluss ausgewählter Modifikationen der Mischungszusammensetzung auf die Eigenschaften von Instandsetzungsmörteln N2 - Trotz der zahlreichen Möglichkeiten zur Beeinflussung der Mörteleigenschaften durch Mischungsmodifikationen ist es nahezu unmöglich, einzelne Eigenschaften unabhängig von anderen zu verändern. Bei einer Mischungsoptimierung muss im Einzelfall immer entschieden werden, welcher der gewünschten Eigenschaften die höchste Priorität zukommt. Anhand von Parameterstudien wird im vorliegenden Artikel verdeutlicht, wie es für bestimmte Anwendungen sinnvoll sein kann, die Verschlechterung einzelner Eigenschaften zu akzeptieren, wenn dadurch eine für den speziellen Einsatzfall essenzielle Eigenschaft verbessert werden kann. Die komplexen Wechselwirkungen der einzelnen Bestandteile fuhren dazu, dass auch scheinbar widersprüchliche Kombinationen von Zusatzmitteln im Einzelfall erforderlich werden können. Zur Anpassung der meisten Mörteleigenschaften gibt es verschiedene Möglichkeiten der Zielerreichung mit jeweils unterschiedlichen Nebeneffekten. Frisch- und Festmörteleigenschaften sind dabei gleichermaßen zu beachten. T2 - 2. Kolloquium "Erhaltung von Bauwerken" CY - Ostfildern/Stuttgart, Germany DA - 25.01.2011 KW - Betoninstandsetzung KW - Instandsetzungsmörtel KW - Modulare Systeme KW - Polymer cement mortar (PCC) KW - Sprayed polymer cement mortar (SPCC) PY - 2011 SN - 3-924813-87-6 SP - 213 EP - 221 AN - OPUS4-23218 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rethmeier, Michael A1 - Brauser, Stephan A1 - Weber, Gert T1 - Potential of optical strain field measurement for the characterisation of the properties of resistance-spot-welded joints N2 - For the designing of safety-relevant components particularly by means of finite element calculations, great significance is attached to the determination of local material parameters in the welding region. Conventional test methods can merely provide global parameters which, however, are frequently not sufficient precisely for the calculation of resistance-spot-welded components since these are characterised by the existence of joining zones with tight local limitations. In contrast, modern test methods such as optical strain field measurement permit the determination of the characteristic material data for concrete locations and times. In order to establish the potential of optical strain field measurements for the characterisation of the local material behaviour of spotwelded joints, tensile shear tests as well as tensile tests were carried out on resistance-spot-welded high-strength steels. The results show the high potential of this procedure not only for the quantification of the local strain behaviour in the joining region but also for the determination of local characteristic material data. PY - 2011 SN - 1612-3433 VL - 10 IS - 1 SP - 48 EP - 52 PB - DVS - German Welding Society CY - Düsseldorf AN - OPUS4-23220 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Antoni, S. A1 - Clemens, J. A1 - Kunath, K. A1 - Rabe, J. A1 - Simon, K. A1 - Uhlig, S. A1 - Wehrstedt, Klaus-Dieter T1 - Evaluation of the 3rd round robin on solid oxidizer test (UN O.1) with calcium peroxide, sodium nitrate, sodium perborate monohydrate N2 - The classification of solid oxidizers according to the regulations on the transport of dangerous goods (based on the UN Recommendations/Model Regulations and accepted by all international organisations for the transport of dangerous goods as ADR, IMO, IATA) and in future also according to the GHS (Globally Harmonized System of Classification and Labelling of Chemicals) is performed on the basis of the results of the UN test O.1 (UN test O.1 ―Test for oxidizing solids‖ described in chapter 34.4.1 in the Recommendations on the Transport of Dangerous Goods – Manual of Tests and Criteria, see [1]). This test was introduced into the UN Manual of Tests and Criteria in 1995 as a replacement for a similar test from 1986. Even if the UN O.1 test as described in the current 5th revised edition of UN Manual of Tests and Criteria gives some improvements compared to the old test, which had had many deficiencies, there are still some problems left with this test in terms of e.g. repeatability or reproducibility of test results, how to handle compacted or multilayer formulations like tablets, toxicity and partly significantly varying particle size distribution within defined fractions of 150 μm to 300 μm of the reference oxidizer potassium bromate (KBrO3). For this reason the IGUS EOS working group installed an ad-hoc working group in 2002 assigned with the task to propose solutions for the existing problems. The appropriateness of such proposed solutions has to be proved by the method of interlaboratory (round robin) tests before they are presented for the adoption to the UN Committee of Experts on the TDG and on the GHS with a proposal of a completely revised test procedure. KW - Round robin KW - Solid oxidizer test KW - United Nations KW - IGUS KW - EOS KW - Calcium peroxide KW - Sodium nitrate KW - Sodium perborate monohydrate PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-232246 SN - 978-3-9813853-7-3 IS - Final Report, 2009 - 2011 SP - 1 EP - 192 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-23224 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Moreno-Gordaliza, E. A1 - Esteban-Fernández, D. A1 - Giesen, Charlotte A1 - Lehmann, K. A1 - Lázaro, A. A1 - Canas, B. A1 - Tejedor, A. A1 - Scheler, Ch. A1 - Jakubowski, Norbert A1 - Linscheid, M. A1 - Gómez-Gómez, M. T1 - LA-ICP-MS for the detection on Pt-binding proteins in biological samples after PAGE/2-DE separations T2 - European Winter Conference on Plasma Spectrochemistry CY - Zaragoza, Spain DA - 2011-01-30 PY - 2011 AN - OPUS4-23227 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wehrstedt, Klaus-Dieter A1 - Malow, Marcus T1 - Letter to the Editor - Comments on the "Letter to the editor" by M.-L. You and C.-M. Shu (Journal of Thermal Analysis and Calorimetry, 2010;100:367-369) as response to the "Letter to the editor" by M. Malow and K.-D. Wehrstedt (Journal of Thermal Analysis and Calorimetry, 2009;98:885-886) KW - Dilauroyl peroxide KW - Oxygen balance KW - DSC KW - Simulation KW - SADT PY - 2011 DO - https://doi.org/10.1007/s10973-010-1122-0 SN - 1388-6150 SN - 1418-2874 SN - 0368-4466 SN - 1572-8943 VL - 103 IS - 1 SP - 409 EP - 410 PB - Kluwer Academic Publ. CY - Dordrecht AN - OPUS4-23210 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krumphals, F. A1 - Wlanis, T. A1 - Sievert, Rainer A1 - Wieser, V. A1 - Sommitsch, C. T1 - Damage analysis of extrusion tools made from the austenitic hot work tool steel Böhler W750 N2 - During hot extrusion of copper alloys, extrusion tools have to withstand cyclic thermal and mechanical loads. To enhance the service life of the tools, materials with high temperature strength are designed as well as an optimised process control is performed. To characterise the tool damage evolution during service and to improve process guiding, modelling and simulation are appropriate means. The extrusion process of copper billets at three different temperatures was simulated by an FE-program to obtain the temporal boundary conditions, i.e. stress and temperature distributions at the interface billet-liner. Those boundary conditions were used to simulate the elastic–viscoplastic behaviour of the tool steel Böhler W750 in service by means of Abaqus Standard™ v.6.8-3 software in conjunction with Z-Mat package. A lifetime rule was added in order to compute the lifetime consumption and the cycles to failure. KW - Hot work tool steel KW - Damage evolution KW - Lifetime prediction KW - Copper extrusion PY - 2011 DO - https://doi.org/10.1016/j.commatsci.2010.04.022 SN - 0927-0256 VL - 50 IS - 4 SP - 1250 EP - 1255 PB - Elsevier CY - Amsterdam AN - OPUS4-23215 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dreßler, Martin A1 - Dombrowski, Felix A1 - Simon, Ulla A1 - Börnstein, Julian A1 - Hodoroaba, Vasile-Dan A1 - Feigl, Michael A1 - Grunow, Sabrina A1 - Gildenhaar, Renate A1 - Neumann, Martin T1 - Influence of gelatine coatings on compressive strength of porous hydroxyapatite ceramics N2 - Porous ceramics prepared by the foam replication technique have a high porosity and low mechanical stability. It has been reported that coating such porous ceramics with gelatin allows for an improved compressive strength. Little details regarding the influence of important gelatin parameters such as concentration, temperature and drying conditions as well as bloom number which is a measure of the gel rigidity, on this toughening effect are available. This paper investigates the influence of these parameters on compressive strength of gelatin coated porous hydroxyapatite ceramics. It was found that concentration in the gelatin sols has a marked impact whereas sol temperature, bloom number and differing conditions during subsequent drying have only little influence on the compressive strength of the coated ceramics. KW - Films KW - Composites KW - Strength KW - Apatite KW - Biomedical application PY - 2011 DO - https://doi.org/10.1016/j.jeurceramsoc.2010.11.004 SN - 0955-2219 SN - 1873-619X VL - 31 IS - 4 SP - 523 EP - 529 PB - Elsevier Ltd. CY - Oxford AN - OPUS4-23216 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schalau, Bernd T1 - Störfallauswirkungsbetrachtungen im Rahmen der Flächennutzungsplanung T2 - Gemeinsame Sitzung der Qualitätszirkel "Bauleitplanung" und "Vollzug der StörfallV", 03.02.2011 CY - Hanover, Germany DA - 2011-02-03 PY - 2011 AN - OPUS4-23160 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hinrichs, R. A1 - Vasconcellos, M.A.Z. A1 - Österle, Werner A1 - Prietzel, Claudia T1 - A TEM snapshot of magnetite formation in brakes: the role of the disc's cast iron graphite lamellae in third body formation N2 - A cross-section sample of the friction film formed on top of a disc during a brake testing procedure against Polymer Matrix Composite pads was made using a Focused Ion Beam (FIB). The FIB-cut sampled the "third body" magnetite layer and the upper part of the cast iron disc containing a graphite flake. Images of the sample examined in a Energy Filtered Transmission Electron Microscope captured an instant view of the important role of the graphite flakes in magnetite formation, where few layer graphene batches interacted with the iron border promoting cracking and oxidation along the graphite–iron interface. The resulting nano-scale interlayer of magnetite and strongly disordered graphite formed a third body which yielded adequate brake performance. KW - Cast iron KW - Carbon KW - Graphite KW - Tribochemistry KW - Electron microscopy PY - 2011 DO - https://doi.org/10.1016/j.wear.2010.11.008 SN - 0043-1648 VL - 270 IS - 5-6 SP - 365 EP - 370 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-23189 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wipfler, B. A1 - Machida, R. A1 - Müller, Bernd R. A1 - Beutel, R.G. T1 - On the head morphology of Grylloblattodea (insecta) and the systematic position of the order, with a new nomenclature for the head muscles of Dicondylia N2 - External and internal head structures of adults of Galloisiana yuasai (Grylloblattodea) are described. The results are compared with conditions found in representatives of other lower neopteran lineages, notably in Austrophasma and Karoophasma (both Mantophasmatodea). Sutures and ridges of the head capsule are discussed. A new nomenclature for head muscles is presented for the entire Dicondylia (= Zygentoma + Pterygota). Galloisiana (like its sister taxon Grylloblatta) is mostly characterized by plesiomorphic features, such as the largely unspecialized orthopteroid mouthparts, the multisegmented filiform antennae, the presence of trabeculae tentorii, the absence of muscles associated with the antennal ampullae, the presence of musculus stipitalis transversalis (0mx11) and the presence of musculus tentoriofrontalis anterior (0te2). Autapomorphies of Grylloblattodea are: (i) compound eyes composed of only 60 ommatidia or less; (ii) a lacinia with a proximal tooth; (iii) a rounded submentum; (iv) loss of musculus craniohypopharyngealis (0hy3); and (v) loss of musculus labroepipharyngealis (0lb5). The phylogenetic evaluation of 104 characters of the head yields a branching pattern with Grylloblattodea as a sister group of Mantophasmatodea in clade Xenonomia. Putative synapomorphies of both taxa are: (i) a distinct angle (more than 60°) between the submentum and the mentum; (ii) posteriorly oriented labial palpi; (iii) a flat and lobe-like hypopharynx with a suspensorium far ventrad of the anatomical mouth opening; (iv) loss of musculus tentorioparaglossalis (0la6); and (v) a connection between the antennal ampulla and the supraoesophageal ganglion containing nuclei. Xenonomia is placed in a clade with the two dictyopteran terminals. Another monophyletic group is Embioptera + Phasmatodea. Most branches of the single tree obtained in our analysis are weakly supported. The results clearly show that more data and a much broader taxon sampling are required to clarify the phylogenetic interrelationships of the lower neopteran orders. However, our results narrow down the spectrum of possible solutions, and represent a starting point for future phylogenetic analyses, with an extensive concatenated dataset. KW - X-ray computed tomography KW - Grylloblattodea KW - Dicondylia PY - 2011 DO - https://doi.org/10.1111/j.1365-3113.2010.00556.x SN - 0307-6970 VL - 36 IS - 2 SP - 241 EP - 266 PB - Blackwell CY - Oxford [u.a.] AN - OPUS4-23190 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Blanchard, Robert A1 - Arndt, Detlef A1 - Grätz, Rainer A1 - Scheider, Swen T1 - Effect of ignition position on the run-up distance to DDT for hydrogen-air explosions N2 - The method described in this paper enabled reliable and accurate positioning of an overdriven detonation by calculation of shock wave velocities (detonation and retonation) for hydrogen explosions in a closed 18 m long horizontal DN150 pipe. This enabled an empirical correlation between the ignition position and the run-up distance to DDT to be determined. It was shown that the initial ability of the flame to expand unobstructed and the piston-like effect of burnt gas expanding against the closed end of the tube contributed to initial flame acceleration and hence were able to affect the run-up distance to overdriven detonation. Flame speeds and rates of initial pressure rise were also used to explain how these two competing effects were able to produce a minimum in the run-up distance to DDT. The shortest run-up distance to DDT, relative to the ignition position, for this pipe and gas configuration was found when the ignition position was placed 5.6 pipe diameters (or 0.9 m) from the closed pipe end. The shortest run-up distance to DDT relative to the end of the pipe was recorded when the ignition source was placed 4.4 pipe diameters or 0.7 m from the pipe end. KW - Deflagration to detonation transition (DDT) KW - Ignition position KW - Hydrogen KW - Detonation and retonation PY - 2011 DO - https://doi.org/10.1016/j.jlp.2010.12.007 SN - 0950-4230 SN - 1873-3352 VL - 24 SP - 194 EP - 199 PB - Butterworth CY - Guildford, Surrey AN - OPUS4-23149 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stegemann, Bert A1 - Klemm, M. A1 - Horn, S. A1 - Woydt, Mathias T1 - Switching adhesion forces by crossing the metal-insulator transition in Magnéli-type vanadium oxide crystals N2 - Magnéli-type vanadium oxides form the homologous series VnO2n-1 and exhibit a temperature-induced, reversible metal–insulator first order phase transition (MIT). We studied the change of the adhesion force across the transition temperature between the cleavage planes of various vanadium oxide Magnéli phases (n = 3 ... 7) and spherical titanium atomic force microscope (AFM) tips by systematic force–distance measurements with a variable-temperature AFM under ultrahigh vacuum conditions (UHV). The results show, for all investigated samples, that crossing the transition temperatures leads to a distinct change of the adhesion force. Low adhesion corresponds consistently to the metallic state. Accordingly, the ability to modify the electronic structure of the vanadium Magnéli phases while maintaining composition, stoichiometry and crystallographic integrity, allows for relating frictional and electronic material properties at the nano scale. This behavior makes the vanadium Magnéli phases interesting candidates for technology, e.g., as intelligent devices or coatings where switching of adhesion or friction is desired. KW - Adhesion force KW - Atomic force microscopy KW - Magnéli phases KW - Metal-insulator transition KW - Vanadium oxide PY - 2011 DO - https://doi.org/10.3762/bjnano.2.8 SN - 2190-4286 VL - 2 SP - 59 EP - 65 CY - Frankfurt, M. AN - OPUS4-23155 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ried, Peter A1 - Gaber, Martin A1 - Beyer, Katrin A1 - Müller, Ralf A1 - Kipphardt, Heinrich A1 - Kannengießer, Thomas T1 - Thermo Analytic Investigation of Hydrogen Effusion Behavior - Sensor Evaluation and Calibration N2 - The well established carrier gas analysis (CGA) method was used to test different hydrogen detectors comprising a thermal conductivity detector (TCD) and a metal oxide semiconducting (MOx) sensor. The MOx sensor provides high hydrogen sensitivity and selectivity, whereas the TCD exhibits a much shorter response time and a linear hydrogen concentration dependency. Therefore, the TCD was used for quantitative hydrogen concentration measurements above 50?µmol/mol. The respective calibration was made using N2/H2 gas mixtures. Furthermore, the hydrogen content and degassing behaviour of titanium hydride (TiH2-x) was studied. This material turned out to be a potential candidate for a solid sample calibration. Vacuum hot extraction (VHE) coupled with a mass spectrometer (MS) was then calibrated with TiH2-x as transfer standard. The calibration was applied for the evaluation of the hydrogen content of austenitic steel samples (1.4301) and the comparison of CGA-TCD and VHE-MS. KW - Hydrogen KW - Steel KW - Vacuum hot extraction KW - Carrier gas analysis KW - Titanium hydride KW - Gas calibration PY - 2011 DO - https://doi.org/10.1002/srin.201000237 SN - 1611-3683 SN - 0177-4832 VL - 82 IS - 1 SP - 14 EP - 19 PB - Verl. Stahleisen CY - Düsseldorf AN - OPUS4-23202 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feigl, Michael A1 - Pulz, Robert A1 - Sojref, Regine A1 - Feldmann, Ines A1 - Dörfel, Ilona A1 - Rehmer, Birgit A1 - Nofz, Marianne T1 - Nd: YAG laser induced thermal shock testing of oxidation preotecting sol-gel alumina coatings on Ni-base alloys T2 - Eurocorr 2011 CY - Stockholm, Sweden DA - 05.09.2011 PY - 2011 AN - OPUS4-23203 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Jaunich, Matthias T1 - Investigation of ethylene/vinyl acetate copolymer (EVA) by thermal analysis DSC and DMA N2 - Two types of commercially applied Ethylene/Vinyl Acetate Copolymers (EVA) for encapsulation of photovoltaic modules were investigated by the thermal analysis methods of Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA) in the temperature range from -150 °C to 200 °C. Glass transition, crystal melting and cross-linking were analyzed. The aims of the investigations were to gain more information for incoming goods control and to get information about the whole temperature dependent material properties in the investigated temperature range, starting at very low temperatures up to the crosslinking temperature region. KW - EVA KW - Thermal analysis KW - DSC KW - DMA KW - Glass transition KW - Crystal melting KW - Cross-linking PY - 2011 DO - https://doi.org/10.1016/j.polymertesting.2010.12.003 SN - 0142-9418 VL - 30 IS - 2 SP - 236 EP - 242 PB - Elsevier Ltd. CY - Amsterdam [u.a.] AN - OPUS4-23206 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfeil, Norbert T1 - Warum über Risiko reden, wenn es um Sicherheit geht? T2 - Security Forum 2011 CY - Brandenburg an der Havel, Germany DA - 2011-01-27 PY - 2011 AN - OPUS4-23175 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vöse, Markus A1 - Fedelich, Bernard T1 - A simplified model for multiple cavity growth controlled by boundary diffusion under creep loading T2 - 2nd International Conference on Material Modelling CY - Paris, France DA - 2011-08-31 PY - 2011 AN - OPUS4-23180 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Woydt, Mathias T1 - Polyglycols as future lubricants T2 - OilDoc Conference & Exhibition CY - Rosenheim, Germany DA - 2011-02-01 PY - 2011 AN - OPUS4-23142 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krietsch, Arne A1 - Scheid, Marc T1 - Brand- und Explosionsgefahren beim Umgang mit Nanostäuben und ultrafeinen Partikeln T2 - 58. Sitzung des Arbeitskreises "Brennbare Stäube" CY - Berlin, Germany DA - 2011-05-26 PY - 2011 AN - OPUS4-23828 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bagda, E. A1 - Borho, N. A1 - Schoknecht, Ute T1 - Measuring the release - Leaching of biocides from facade coatings N2 - Facades are attacked by algae and fungi during weathering, impairing the surfaces visually and leading to long-term damage. To prevent this, appropriate biocides are used in facade coatings. These can be washed out during weathering, especially when it rains. A standardized laboratory procedure to determine the amount of biocides released under practical conditions has been developed and is accessible as European Standard FprEN 16105. KW - Leaching KW - Fassadenbeschichtungen KW - prEN 16105 KW - Testparameter KW - INS-Projekt PY - 2011 SN - 0930-3847 VL - 06 SP - 33 EP - 37 PB - Vincentz CY - Hannover AN - OPUS4-23829 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Roos, P.H. A1 - Jakubowski, Norbert T1 - Cytochromes - fascinating molecular machines N2 - A huge number of functions and reactions can be performed by proteins merely based on their amino acids and their spatial arrangement which results in a specific geometric and electronic environment. The diversity and efficiency of functions, however, can be increased by protein-bound cofactors which fulfil their task in close interaction with the surrounding amino acid side chains. Among these cofactors, metals play an important role. They can be bound to proteins directly via specific amino acids such as cysteine and histidine, for example in zinc finger proteins or in iron sulfur cluster proteins. Another possibility is their integration into the 3D-structure of a protein via a prosthetic group. Porphyrine or porphyrine-like molecules with copper or iron as central bound metal ions constitute important structures in this respect. PY - 2011 DO - https://doi.org/10.1039/c1mt90012a SN - 1756-5901 SN - 1756-591X VL - 3 SP - 316 EP - 318 PB - RSC Publ. CY - Cambridge AN - OPUS4-23830 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kluge, Martin A1 - Ferrero, Fabio T1 - Modeling helps improve safety in the production of teflon KW - Self ignition KW - Numerical simulation KW - MITD KW - TFE PY - 2011 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. SP - 44 EP - 45 AN - OPUS4-23831 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schulze, Dietmar A1 - Fengler, Petra A1 - Stark, Wolfgang T1 - Die Ermittlung von Ozonkonzentrationen bei der Prüfung der Ozonbeständigkeit von Elastomeren N2 - Dargestellt wird eine Gegenüberstellung der Ergebnisse von Messungen zur Ozonkonzentrationsbestimmung nach zwei Verfahren. International wird in der Kautschukindustrie ein UV-spektroskopisches Verfahren angewandt. Die deutsche Kautschukindustrie verwendet ein nasschemisches Verfahren. Die beiden Verfahren ergeben nicht die gleichen Ergebnisse. Daher wird der Unterschied genauer ermittelt. Die Auswirkungen der unterschiedlichen Ozonkonzentrationsbestimmungen auf die Prüfung der Ozonbeständigkeit an Elastomeren werden gezeigt. KW - Ozonkonzentrationsbestimmung KW - UV-Spektroskopie KW - Nasschemische Analyse KW - Ozonbeständigkeit KW - Elastomere PY - 2011 SN - 0948-3276 SN - 0022-9520 VL - 05 SP - 15 EP - 19 PB - Hüthig CY - Heidelberg AN - OPUS4-23832 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hünert, Daniela A1 - Kranzmann, Axel T1 - Impact of oxyfuel atmospheres H2O/CO2/O2 and H2O/CO2 on the oxidation of ferritic-martensitic and austenític steels N2 - In future power plant technologies, oxyfuel, steels are subjected to steam rich and carbon dioxide rich combustion gases. The effect of simulated combustion gases H2O/CO2/O2 (30/69/1 mol%) and H2O/CO2 (30/70 mol%) on the corrosion behavior of low alloyed steels, 9-12% chromium steels and an austenitic steel were studied. It was discovered that the formation of protective chromium rich oxides is hampered due to the carburization of the base material and the formation of chromium rich carbides. The kinetics of corrosion and carburization are quantified. The effect of temperature and the effect of gas pressure are analyzed statistically. KW - A. Steel KW - C. Oxidation KW - C. Carburization KW - C. High temperature corrosion PY - 2011 DO - https://doi.org/10.1016/j.corsci.2011.03.015 SN - 0010-938X VL - 53 IS - 6 SP - 2306 EP - 2317 PB - Elsevier CY - Orlando, Fla. AN - OPUS4-23833 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niebergall, Ute A1 - Weltschev, Margit T1 - Comparison of the stress crack resistance of polyethylene grades with the test performance behaviour of packagings for the transport of dangerous goods N2 - Resistance to stress cracking by wetting solution is one of the selected properties together with the corresponding test method FNCT and tolerances for a comparison of polyethylene grades of one design type in the procedural rule on suitability proof for alternative plastic resins used for packagings and intermediate bulk Containers (IBCs) for the transport of dangerous goods. The environmental stress crack resistance determined by Full Notch Creep Test (FNCT) represents the impacts from the stacking tests at 40 °C performed with Standard liquid wetting solution (without pre-storage) and with normal butyl acetate saturated wetting solution (pre-storage with normal butyl acetate). Environmental stress crack resistance determined with FNCT for the polyethylene grades was related to the times to failure of different jerrican samples made of these grades in stacking tests with 5 % wetting solution and a n-butyl acetate saturated wetting solution (pre-storage with n-butyl acetate) at 40 °C. The FNCT is suitable for comparison of polyethylene grades in relation to environmental stress crack resistance independent of their use as drum, IBC or jerrican material. The stiffness of polyethylene grades should be taken into account to the comparison as jerricans are not only chemically but also mechanically stressed. T2 - PPS-27 - 27th World congress of the polymer processing society CY - Marrakech, Morocco DA - 10.05.2011 KW - Gefahrgutverpackungen KW - Polyethylenformstoffe KW - Full notch creep test KW - Stapeldruckprüfung PY - 2011 SP - 1 EP - 4 AN - OPUS4-23834 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Heinze, Christoph A1 - Schwenk, Christopher A1 - Rethmeier, Michael A1 - Caron, J. T1 - Numerical sensitivity analysis of welding-induced residual stress depending on variations in continuous cooling transformation behavior N2 - The usage of continuous cooling transformation (CCT) diagrams in numerical welding simulations is state of the art. Nevertheless, specifications provide limits in chemical composition of materials which result in different CCT behavior and CCT diagrams, respectively. Therefore, it is necessary to analyze the influence of variations in CCT diagrams on the developing residual stresses. In the present paper, four CCT diagrams and their effect on numerical calculation of residual stresses are investigated for the widely used structural steel S355J2 + N welded by the gas metal arc welding (GMAW) process. Rather than performing an arbitrary adjustment of CCT behavior, four justifiable data sets were used as input to the numerical calculation: data available in the Sysweld database, experimental data acquired through Gleeble dilatometry tests, and TTT/CCT predictions calculated from the JMatPro and Edison Welding Institute (EWI) Virtual Joining Portal software. The performed numerical analyses resulted in noticeable deviations in residual stresses considering the different CCT diagrams. Furthermore, possibilities to improve the prediction of distortions and residual stress based on CCT behavior are discussed. KW - Welding simulation KW - GMAW KW - CCT sensitivity KW - Welding residual stress PY - 2011 DO - https://doi.org/10.1007/s11706-011-0131-7 SN - 1673-7377 SN - 1673-7482 VL - 5 IS - 2 SP - 168 EP - 178 PB - Springer ; [Beijing] : Higher Education Press CY - Secaucus, N.J. ; Heidelberg AN - OPUS4-23835 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tölle, Florian A1 - Gumenyuk, Andrey A1 - Gebhardt, Moritz Oliver A1 - Rethmeier, Michael T1 - Post-weld residual stress mitigation by scanning of a defocused laser beam N2 - High welding residual stresses can cause service life reducing consequences. Even though many processes have been developed to reduce these stresses, they are only applicable for wider welds and simple component geometries or are cost-intensive, respectively. The presented method uses a defocused beam after welding for heating the material regions on both sides of the weld. In this way, the welding stresses are decreased without contacting the surfaces using the available equipment. Different process parameters could be used depending on the component geometry and the laser power. The mechanism and the influence of the process parameters were investigated by FEM-simulation and experiments on S355J2+N steel and showed a stress reduction of about 73%. T2 - Lasers in Manufacturing 2011 - Proceedings of the Sixth International WLT Conference on Lasers in Manufacturing CY - Munich, Germany DA - 23.05.2011 KW - Residual stresses KW - Stress reduction KW - High energy beam welding KW - Post-weld heat treatment KW - Laser scanner optics PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-238482 DO - https://doi.org/10.1016/j.phpro.2011.03.052 SN - 1875-3892 VL - 12 IS - 1 SP - 410 EP - 418 PB - Elsevier CY - Amsterdam [u.a.] AN - OPUS4-23848 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ferrero, Fabio A1 - Malow, Marcus A1 - Noll, Matthias T1 - Temperature and gas evolution during large scale outside storage of wood chips N2 - The temperature and gas concentrations in a newly established pine-wood debris pile of 20 m × 15 m × 6 m in dimensions (approximately 400 tons of fresh weight material) were monitored for 150 days. Temperature was measured at ten different positions within the pile, while concentrations of CO2, O2, CO and CH4 were taken at four different representative locations. The pile was characterized by a strong temperature increase within the first 10– 12 days of storage. Results of the gas analysis in this period suggest that the temperature increase was caused by microbial processes. In particular, reduced oxygen concentration and almost complete absence of methane indicate mainly aerobic respiration processes. Effects of weather conditions on the temperature/gas distribution and time evolution are also discussed in the paper. KW - Wood KW - Storage KW - Temperature KW - Gas concentration PY - 2011 DO - https://doi.org/10.1007/s00107-010-0512-0 SN - 0018-3768 VL - 69 IS - 4 SP - 587 EP - 595 PB - Springer CY - Berlin ; Heidelberg AN - OPUS4-23849 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lorenz, Stephan A1 - Kannengießer, Thomas A1 - Posch, G. T1 - Eignung hochlegierter Fülldrahtelektroden zum Laserstrahl-MSG-Hybridschweißen N2 - Gegenstand dieses Forschungsprojekts waren Untersuchungen zur Qualifikation von Fülldrahtelektroden für das Laserstrahl-MSG-Hybridschweißen hochlegierter Stähle. Dieser Typ Drahtelektrode ermöglicht aufgrund seines ringförmigen Metallmantels und der pulverartigen Füllung insbesondere im oberen Bereich der erzielbaren Abschmelzleistungen einen stabilen, spritzerarmen Werkstoffübergang vergleichbar dem im Sprühlichtbogen. Im Gegensatz dazu wird beim Abschmelzen von Massivdrahtelektroden ein kontrollierter Werkstoffübergang durch die Impulslichtbogentechnik erreicht. Die Werkstoff- und prozessspezifischen Eigenschaften beim Schweißen dieser Zusatzwerkstoffe haben einen signifikanten Einfluss auf die Schweißnahtmetallurgie sowie die Prozessstabilität. Zur Untersuchung der Übertragbarkeit der erzielbaren Werkstoffeigenschaften vom MSG-Schweißen auf das Laserstrahl-MSG-Hybridschweißen wurden Versuche am hochlegierten Grundwerkstoff AISI403L (X2CrNil911) durchgeführt. Als Zusatzwerkstoffe gemäß DIN EN 12 072 und DIN EN ISO 17 633 kamen vier Drahtelektroden, ein eigens für das Positionsschweißen konzipierter Rutilfülldraht 19 9 L P M1, ein zum Schweißen in Wannenposition geeigneter Rutilfülldraht T 19 9 L R M (C) 3, ein Metallpulverfülldraht T199LMM1 sowie ein Massivdraht G19 9 L Si zum Einsatz. KW - Fülldrahtelektroden KW - Laserstrahlschweißen KW - Metall-Schutzgasschweißen KW - Hybridschweißen KW - Werkstofffragen KW - Zusatzwerkstoffe PY - 2011 SN - 0036-7184 VL - 63 IS - 5 SP - 222 EP - 228 PB - Verl. für Schweißen u. Verwandte Verfahren, DVS-Verl. CY - Düsseldorf AN - OPUS4-23850 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin A1 - Wille, Frank T1 - Rechnerische Simulation des mechanischen Verhaltens von holzgefüllten Stoßdämpfern von Transportbehältern für radioaktive Stoffe N2 - Basierend auf Fallversuchen mit Transportbehältern für radioaktive Stoffe sowie auf einem Versuchsprogramm mit Holzproben wurden die Energieabsorptionsmechanismen identifiziert und ein Modell für das Verhalten von Fichtenholz bei axialer Belastung entwickelt. Das Modell zieht für die Kompression von Holz die seitliche Dehnungsbehinderung – im kontinuumsmechanischen Zusammenhang wäre das die Mehrachsigkeit des Spannungszustandes im Kontinuum – in Betracht. Die Energie, die vom Holz absorbiert werden kann, ist umso größer, je größer die seitliche Dehnungsbehinderung ist. Für die Modellierung mit Finite Elemente Methoden wurden verschiedene Modellierungsstrategien untersucht, keine der vorgeschlagenen Modellierungsstrategien war in der Lage, dass Verhalten von Holz bei Druckbeanspruchung und großen Deformationen inkl. der Entfestigung zu modellieren. Bei Verwendung einer entfestigenden Fließkurve zeigt das Modell ausgeprägte Netzabhängigkeiten und numerischen Instabilitäten. Für die Modellierung der Entfestigung mit Hilfe einer von der Mehrachsigkeit des Spannungszustandes gesteuerten Fließflächenevolution ist kein geeignetes Materialmodell vorhanden. Anhand der Simulation eines Fallversuchs mit einem Behälterkörper und stoßdämpfenden Bauteilen im Maßstab 1:2 wurde gezeigt, dass zwar eine vollständige Modellierung des Stoßdämpferverhaltens inkl. Entfestigung nicht möglich war, aber das Stoßdämpferverhalten mit einer nicht-entfestigenden Fließkurve sinnvoll modelliert werden konnte. Eine Verifikation des Modellierungsansatzes am real zu modellierenden Bauteil ist zwingend erforderlich. Wenn signifikante Änderungen zwischen Verifikations- und Simulationsobjekt auftreten, ist die Zuverlässigkeit der Rechenergebnis als gering zu bewerten. Nur wenn die auftretenden Kompressionsmechanismen durch eine Analyse des Stoßdämpferholzes bestimmt werden können, ist eine zuverlässige Ermittlung von Stoßdämpferkräften- und verformungen möglich. T2 - Jahrestagung Kerntechnik 2011 CY - Berlin, Germany DA - 17.05.2011 KW - Radioaktive Stoffe KW - Transport KW - Stoßdämpfende Bauteile KW - FEM KW - Simulation PY - 2011 SP - 1 EP - 6 AN - OPUS4-23851 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Aris, Stephan T1 - Aktuelle Entwicklungen im Bereich der Europäischen Richtlinien über Druckgeräte (PED, SPVD und TPED) Teil 2: Richtlinie 1999/36/EG (bzw. diese ab 1. Juli 2011 ersetzende Richtlinie 2010/35/EU) über ortsbewegliche Druckgeräte N2 - Die Europäische Richtlinie über ortsbewegliche Druckgeräte (1999/36/EG – TPED) wird am 1. Juli 2011 durch die neue TPED (Richtlinie 2010/35/EU) ersetzt. Im Rahmen der Revision der Richtlinie wurden deren technischen Inhalte komplett ins Gefahrgutrecht übernommen. Die neue TPED schreibt für alle ortsbeweglichen Druckgeräte ein einheitliches Konformitätsbewertungsverfahren vor, wobei die Pi-Kennzeichnung beibehalten wird. Bedingt durch die teilweise geregelten Übergangsvorschriften wird die Umstellung auf die neue TPED erst zum 1. Januar 2013 beendet sein. KW - Ortsbewegliche Druckgeräte KW - TPED KW - ADR PY - 2011 SN - 2191-0073 VL - 1 IS - 6 SP - 32 EP - 36 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-23852 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krause, Martin A1 - Mayer, K. A1 - Friese, Martin A1 - Milmann, Boris A1 - Mielentz, Frank A1 - Ballier, G. T1 - Progress in ultrasonic tendon duct imaging N2 - Ultrasonic imaging of tendon ducts enables the precise localisation of grouting faults in many cases. Additionally to well known criteria for detecting grouting faults in tendon ducts recently new possibilities were developed. Two main effects influence the complex behaviour of wave propagation and reflection: a) different arrangement and number of strands or internal rebars; b) superposition of reflecting signals and different wave modes propagating into the interface region around the tendon duct. In order to understand the experimental results, EFIT modelling is performed (EFIT: Elastodynamic Finite Integration Technique). KW - Ultrasonic imaging KW - Prestressed concrete structures KW - Reconstruction calculation KW - SAFT KW - EFIT modelling PY - 2011 DO - https://doi.org/10.3166/ejece.15.461-485 SN - 1964-8189 VL - 15 IS - 4 SP - 461 EP - 485 PB - Lavoisier CY - Paris AN - OPUS4-23853 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kargl, F. A1 - Engelhardt, M. A1 - Yang, F. A1 - Weis, H. A1 - Schmakat, P. A1 - Schillinger, B. A1 - Griesche, Axel A1 - Meyer, A. T1 - In situ studies of mass transport in liquid alloys by means of neutron radiography N2 - When in situ techniques became available in recent years this led to a breakthrough in accurately determining diffusion coefficients for liquid alloys. Here we discuss how neutron radiography can be used to measure chemical diffusion in a ternary AlCuAg alloy. Neutron radiography hereby gives complementary information to x-ray radiography used for measuring chemical diffusion and to quasielastic neutron scattering used mainly for determining self-diffusion. A novel Al2O3 based furnace that enables one to study diffusion processes by means of neutron radiography is discussed. A chemical diffusion coefficient of Ag against Al around the eutectic composition Al68.6Cu13.8Ag17.6 at.% was obtained. It is demonstrated that the in situ technique of neutron radiography is a powerful means to study mass transport properties in situ in binary and ternary alloys that show poor x-ray contrast. KW - Neutron radiography KW - Diffusion KW - Liquid alloys KW - Shear cell PY - 2011 DO - https://doi.org/10.1088/0953-8984/23/25/254201 SN - 0953-8984 SN - 1361-648X VL - 23 IS - 25 SP - 254201-1 EP - 254201-8 PB - IOP Publ. Ltd. CY - Bristol AN - OPUS4-23854 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heidt, Heinrich A1 - Portella, Pedro Dolabella T1 - New research themes and applications in NDT and sensor technology T2 - COTEQ 2011 CY - Ipojuca, Brazil DA - 2011-05-11 PY - 2011 AN - OPUS4-23856 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Keßler, S. A1 - Gehlen, C. A1 - Eng, M. A1 - Ebell, Gino A1 - Burkert, Andreas T1 - Validierung zerstörungsfreier Messmethoden zur zuverlässigen Erfassung von Bewehrungskorrosion N2 - Die Ergebnisse der Untersuchungen sind in ein Konzept zur Durchführung und Auswertung der Potentialfeld- und Polarisationsmessung eingegangen, um den Ingenieuren in der Praxis ein effizienten Werkzeug zur zerstörungsfreien Erfassung des Korrosionszustandes anzubieten. Das Ziel des Vorhabens wurde erreicht. KW - Potentialfeldmessung KW - Korrosion KW - Betonstahl KW - Elektrolytwiderstand PY - 2011 UR - http://www.cbm.bv.tum.de/fileadmin/w00bdr/www/pdf/Kurzberichte/KB_26.pdf IS - 26 SP - 1 EP - 2 PB - Technische Universität CY - München AN - OPUS4-23838 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Pfennig, Anja A1 - Wojtas, P. A1 - Spengler, I. A1 - Linke, B. A1 - Kranzmann, Axel ED - Villacampa, V. ED - Brebbia, C.A. ED - Mammoli, A.A. T1 - Influence of heat treatment on the corrosion behavior of steels exposed to CCS environment N2 - The influence of heat treatment on pit corrosion needs to be considered to guarantee reliability and safety during the injection of compressed emission gasses – mainly containing CO2 – into deep geological layers (CCS-technology, Carbon Capture and Storage). In laboratory experiments different heat treated steels used as injection pipe with 13% Chromium and 0.46% Carbon (X46Cr13, 1.4034) as well as 0.2% Carbon (X20Cr13, 1.4021) were tested. Also X5CrNiCuNb16-4 (1.4542) was investigated as typical steel used for geothermal pumps. Keeping stable environmental conditions in laboratory experiments the samples were exposed to the distinct synthetic aquifer environment saturated with technical CO2 at a flow rate of 3 l/h for up to 6 months. Independent of the exposure time the least amount of pits is found on hardened steels with martensitic microstructure where X5CrNiCuNb16-4 shows fewer pits than X46Cr13 and X20Cr13. Regarding steels with similar Cr-content the higher Ccontent in 1.4034 results in fewer pits compared to 1.4021. KW - Steel KW - Heat treatment KW - Pit corrosion KW - CCS KW - CO2-injection KW - CO2-storage PY - 2011 SN - 978-1-84564-508-3 DO - https://doi.org/10.2495/ESUS110411 SN - 1746-448X SN - 1743-3541 SP - 487 EP - 498 PB - WIT Press CY - Southampton, UK AN - OPUS4-23840 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Beckmann, S. A1 - Krüger, M. A1 - Engelen, B. A1 - Gorbushina, Anna A1 - Cypionka, H. T1 - Role of bacteria, archaea and fungi involved in methane realease in abandoned coal mines N2 - Worldwide, abandoned coal mines release substantial amounts of methane, which is largely of biogenic origin. The aim of this study was to understand the microbial processes involved in mine-gas formation. Therefore, coal and timber samples and anaerobic enrichments from two abandoned coal mines in Germany were subjected to DGGE analyses and quantitative PCR. The primers used were specific for Bacteria, Archaea, Fungi, and the key functional genes for sulfate reduction (dsrA) and methanogenesis (mcrA). A broad spectrum of facultative anaerobic bacteria and acetogens belonging to all five groups (α-ε) of the Proteobacteria, as well as the Bacteroidetes, Tenericutes, Actinobacteria, Chlorobi and Chloroflexi were detected. Archaea were represented by acetoclastic Methanosarcinales and Crenarchaeota with an unknown metabolism. Fungi formed thick biofilms particularly on timber, and were identified as typical wood degraders belonging to the Ascomycetes and Basidiomycetes. The community analysis as well as the environmental conditions and the metabolites detected in a previous study are consistent with the following scenario of methane release: Weathering of coal and timber is initiated by wood-degrading Fungi and Bacteria under a suboxic atmosphere. In the lower, oxygen-depleted layers Fungi and Bacteria perform incomplete oxidation and release reduced substrates which can be channeled into methanogenesis. Acetate appeared to be the main precursor of the biogenic methane in the investigated coal mines. KW - Mine gas KW - Community analysis or microbial diversity KW - Quantitative PCR KW - DGGE KW - Acetoclastic methanogenesis KW - Fermentative bacteria KW - Methanosarcinales PY - 2011 DO - https://doi.org/10.1080/01490451.2010.503258 SN - 0149-0451 VL - 28 IS - 4 SP - 347 EP - 358 PB - Crane, Russak & Co. CY - New York, NY, USA AN - OPUS4-23841 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Raedel, Martina A1 - Unger, Brita A1 - Bücker, Michael A1 - Sabel, Martin A1 - Feldmann, Ines T1 - Gold mosaics - material composites and glass-chemical characteristics N2 - In this study gold mosaics front the past 130 years are reviewed and analysed. Characteristic glass properties and technological specifics are observed and provide important Information on the production process. The insights gained are used for replicas with improved glass properties. T2 - GLASSAC 11 - 3rd GLASSAC Conference 'Glass science in art and conservation' CY - Wertheim, Bronnbach Monastery, Germany DA - 01.05.2011 KW - Erfassung von Goldmosaiken der letzten 130 Jahre mit Aufbau einer Datenbank KW - Herstellungstechnik und Besonderheiten KW - Schichtaufbau mit Glaszusammensetzung und EDX-analysen KW - Glas-chemische Charakteristika verschiedener Goldmosaiktypen KW - Reproduktion PY - 2011 SN - 978-3-8396-0255-3 SP - 51 EP - 54 PB - Fraunhofer Verlag AN - OPUS4-23842 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Cross, Carl Edward A1 - Coniglio, Nicolas A1 - Schempp, Philipp A1 - Mousavi, M.G. ED - Lippold, J. ED - Böllinghaus, T. ED - Cross, C.E. ED - et al., T1 - Critical conditions for weld solidification crack growth N2 - The occurrence of solidification cracking during welding remains a little understood phenomenon, in spite of extensive studies and tests performed to evaluate and compare the relative weldability of many different alloys. From an approach often adopted in the welding community attributed to Prokhorov, solidification cracks are believed to form when a critical tensile strain is exceeded, specific to the alloy, assuming that the mushy-zone has limited ductility. Tensile stresses and strains normally form behind a moving weld pool as a result of solidification shrinkage and thermal contraction, as influenced by welding parameters and the degree of restraint. KW - Solidification cracking KW - Aluminium alloy KW - Crack growth KW - Strain rate model PY - 2011 SN - 978-3-642-16863-5 DO - https://doi.org/10.1007/978-3-642-16864-2_2 IS - Part 2 SP - 25 EP - 41 PB - Springer CY - Berlin, Heidelberg AN - OPUS4-23846 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan A1 - Salge, T. A1 - Terborg, R. A1 - Rackwitz, Vanessa T1 - Advanced Elemental Analysis with ED-EPMA, WE-EPMA and µ-XRF at a SEM T2 - IUMAS, 5th International Union of Microbeam Analysis Societies CY - Seoul, South Korea DA - 2011-05-22 PY - 2011 AN - OPUS4-23778 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan A1 - Kühn, Julius A1 - Linke, S. A1 - Moritz, W. A1 - Unger, Wolfgang T1 - Characterization of Pd-Ni-Co Alloy Thin Films by ED-EPMA and Data Reduction by the STRATAGEM Software T2 - IUMAS, 5th International Union of Microbeam Analysis Societies CY - Seoul, South Korea DA - 2011-05-22 PY - 2011 AN - OPUS4-23779 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Siegel, David A1 - Maul, Ronald A1 - Köppen, Robert A1 - Koch, Matthias A1 - Nehls, Irene T1 - Current mycotoxin research at BAM T2 - Mycotoxin Workshop 2011 CY - Freising, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23780 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Siegel, David A1 - Maul, Ronald A1 - Köppen, Robert A1 - Koch, Matthias A1 - Nehls, Irene T1 - Current mycotoxin research at BAM T2 - Gordon Reaearch Seminar & Conference on Mycotoxins and Phycotoxins CY - Waterville, ME, USA DA - 2011-06-11 PY - 2011 AN - OPUS4-23781 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Zündgefahr druch mechanisch erzeugte Funken? T2 - Seminar "Zündgefahren durch Funken - Maßnahmen zum Explosionsschutz"; Veranstaltungs-Nr.: E-H050-05-420-1 CY - Essen, Germany DA - 2011-05-17 PY - 2011 AN - OPUS4-23782 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Regelwerk des nichtelektrischen Explosionsschutzes - von der EU-Richtlinie zur Produktnorm T2 - Seminar "Zündgefahren durch Funken - Maßnahmen zum Explosionsschutz"; Veranstaltungs-Nr.: E-H050-05-420-1 CY - Essen, Germany DA - 2011-05-17 PY - 2011 AN - OPUS4-23783 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nooke, Alida A1 - Krause, Andreas A1 - Krüger, Hannes A1 - Lohse, Volkmar A1 - Hertwig, Andreas A1 - Beck, Uwe A1 - Steinbach, J. T1 - Gas sensing with ellipsometry and surface plasmon resonance T2 - 110. Bunsentagung CY - Berlin, Germany DA - 2011-06-02 PY - 2011 AN - OPUS4-23784 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maierhofer, Christiane A1 - Krankenhagen, Rainer A1 - Röllig, Mathias A1 - Mecke, R. A1 - Schiller, M. A1 - Seidl, T. A1 - Kalisch, U. A1 - Meinhardt, J. A1 - Hennen, C. T1 - Monitoring of damage processes at surface of historic structures using a combination of 3D laser scanner and active thermography T2 - Technart 2011, BAM CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-23786 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Berger, Anka A1 - Krüger, Simone A1 - Krause, Ulrich T1 - Self-ignition of deposits containing Recycling materials - an Underestimated Phenomenon T2 - IV International Symposium MBT & MRF, Waste-to-Resources CY - Hanover, Germany DA - 2011-05-24 PY - 2011 AN - OPUS4-23787 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koch, Matthias A1 - Proske, Matthias A1 - Siegel, David A1 - Riedel, Juliane A1 - Köppen, Robert T1 - Results of an interlaboratory comparison study for the determination of zearalenone in edible oils T2 - Wissenschaftliches Meeting (Expertengespräch) zur Mykotoxin-Analytik (BVL) CY - Berlin, Germany DA - 2011-06-09 PY - 2011 AN - OPUS4-23820 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Larissa A1 - Jakubowski, Norbert A1 - Hayen, H. A1 - Roos, P. H. T1 - Method development for iodination of proteins for LA-ICP-MS based proteomics T2 - European Winter Conference on Plasma Spectrochemistry CY - Zaragoza, Spain DA - 2011-01-30 PY - 2011 N1 - Geburtsname von Müller, Larissa: Wäntig, L. - Birth name of Müller, Larissa: Wäntig, L. AN - OPUS4-23821 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hayen, H. A1 - Polatajko, A. A1 - Feldmann, I. A1 - Jakubowski, Norbert T1 - Identifizierung Cadmium-bindender Proteine in Spinat T2 - Jahrestagung des Regionalverbandes Nordrhein-Westfalen der Lebensmittelchemischen Gesellschaft (Fachgruppe der GDCh) CY - Wuppertal, Germany DA - 2011-03-23 PY - 2011 AN - OPUS4-23824 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lange, Axel A1 - Müller, Bernd R. A1 - Hentschel, Manfred P. A1 - Kupsch, Andreas T1 - Korrektur des Hinterleuchtens an CT-Sychrotrondaten T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23768 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kupsch, Andreas A1 - Lange, Axel A1 - Hentschel, Manfred P. A1 - Manke, I. A1 - Grothausmann, R. T1 - Verbesserte Elektronen-Tomographie mittels DIRECTT-Algorithmus T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23769 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seuthe, T. A1 - Bonse, Jörn A1 - Grehn, M. A1 - Mermillod-Blondin, A. A1 - Rosenfeld, A. A1 - Eberstein, M. T1 - Strukturierung von Silikatgläsern mit unterschiedlicher Komposition durch ultrakurze Lichtpulse T2 - 85. Glastechnische Tagung der Deutschen Glastechnischen Gesellschaft (DGG) CY - Saarbrücken, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23770 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niebergall, Ute A1 - Weltschev, Margit T1 - Comparison of the stress crack resistance of polyethylene grades with the test performance behaviour of the transport of dangerous goods T2 - PPS 27 World Congress of the Polymer Processing Society CY - Marrakesh, Morocco DA - 2011-05-09 PY - 2011 AN - OPUS4-23771 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nitsche, Michael T1 - Qualtitätsinfrastruktur (QI) - Weltweites Netzwerk zu Qualität und Sicherheit bei Produkten und Dienstleistungen - Eine Einführung T2 - Gastvorlesung zur Strategischen Normung, BAM CY - Berlin, Germany DA - 2011-01-13 PY - 2011 AN - OPUS4-23772 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Neue Umweltanforderungen an Produkte - Ökodesignrichtlinie und EBPG T2 - Expertenforum 2011 CY - Bayreuth, Germany DA - 2011-05-26 PY - 2011 AN - OPUS4-23773 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan A1 - Kim, K. Y. A1 - Unger, Wolfgang T1 - ED-EPMA Measurements of elemental Composition and Thickness of Fe-Ni Alloy Films T2 - IUMAS, 5th International Union of Microbeam Analysis Societies CY - Seoul, South Korea DA - 2011-05-22 PY - 2011 AN - OPUS4-23774 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Procop, M. A1 - Hodoroaba, Vasile-Dan A1 - Kemf, N. A1 - Hahn, M. T1 - Investigation of the enrichment of Co and Cr in periprosthetic tissue by scanning electron microscopy and spatial resolved X-ray fluorescence spectroscopy after total hip resurfacing arthroplasty T2 - SCANDEM 2011 - Annual Meeting of Scandinavian Microscopy Society CY - Oulu, Finland DA - 2011-06-08 PY - 2011 AN - OPUS4-23775 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan T1 - Evaluation of the performance of energy dispersive X-ray spectrometers - ISO 15632 and more T2 - IUMAS, 5th International Union of Microbeam Analysis Society CY - Seoul, South Korea DA - 2011-05-22 PY - 2011 AN - OPUS4-23776 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nie, Yaru A1 - Hübert, Thomas A1 - Leistner, A. T1 - Surface modification of carbon nanofibers (CNFs) with silanes for tuning the conductive and mechanical properties of CNFs/epoxy composites T2 - 5th Asia-Europe Symposium on Processing and Properties of Reinforced Polymers CY - Dresden, Germany DA - 2011-05-29 PY - 2011 AN - OPUS4-23777 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Illgen, René A1 - Huber, Alexandra A1 - Hanelt, Sven A1 - Jäger, Christian A1 - Unger, Wolfgang A1 - Meyer-Plath, Asmus T1 - Comparison of XPS and solid-state 19F-NMR measurements of derivatized oxidized MWCNTs T2 - Berliner Chemie Symposium, HU Berlin CY - Berlin, Germany DA - 2011-04-07 PY - 2011 AN - OPUS4-23799 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tölle, Florian T1 - Post-weld residual stress mitigation by scanning of a defocused laser beam T2 - Lasers in Manufacturing CY - Munich, Germany DA - 2011-05-23 PY - 2011 AN - OPUS4-23800 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Bäßler, Ralph T1 - Use of Higher Alloyed Metallic Materials and Duplex Steels for Transport Tanks of Dangerous Goods T2 - Steels in Cars and Trucks (SCT 2011) CY - Salzburg, Austria DA - 2011-06-06 PY - 2011 AN - OPUS4-23801 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Noskov, Sergey A1 - Scherer, Christian A1 - Schupp, W. A1 - Maskos, Michael T1 - Determination of Hamaker constants of polymeric nanoparticles by asymmetrical flow field-flow fractionation T2 - 85th ACS Colloid and Surface Science Symposium CY - Montreal, Canada DA - 2011-06-19 PY - 2011 AN - OPUS4-23803 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wyrwich, Peter A1 - Pittner, Andreas A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - Automatisierter Temperaturfeldabgleich T2 - Workshop "Anwendungsnahe Schweißsimulation", BAM CY - Berlin, Germany DA - 2011-05-19 PY - 2011 AN - OPUS4-23804 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rübner, Katrin A1 - Osterhus, Lennart A1 - Herbst, Tristan A1 - Seidemann, M. A1 - Leydolph, B. A1 - Ballaschk, A1 - Schmidt, K. T1 - Nanoskaliger Kieselsäureschlamm - Verwertung in hydraulischen Bindemitteln T2 - Clustreffen NanoCare/NanoNature-Fördermaßnahmen (öffenltiche Informationsveranstaltung des BMVBS) CY - Frankfurt am Main, Germany DA - 2011-05-10 PY - 2011 AN - OPUS4-23805 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian T1 - Failure Criteria for Fiber Reinforced Materials based on the Interface Strength T2 - ICM11 - International Conference on the Mechanical Behaviour of Materials CY - Como, Italy DA - 2011-06-05 PY - 2011 AN - OPUS4-23806 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubowski, Norbert T1 - Neue Anwendungen der anorganischen Massenspektrometrie in den Lebens- und Materialwissenschaften T2 - Eingeladener Vortrag, Fakultätskolloquium, Technische Universität Bergakademie Freiberg CY - Freiberg, Germany DA - 2011-02-15 PY - 2011 AN - OPUS4-23809 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubowski, Norbert A1 - Tempez, A. A1 - Chapon, P. A1 - Bordel, N. A1 - Pisonero, J. A1 - Lobo, L. T1 - A new Glow Discharge Time of Fligh Mass Spectrometer for Bulk Analysis and Depth Profiling T2 - PITTCON 2010, eingeladener Vortrag CY - Atlanta, GA, USA DA - 2011-03-13 PY - 2011 AN - OPUS4-23810 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taffe, Alexander A1 - Kind, Thomas A1 - Stoppel, Markus A1 - Kurz, J. T1 - OSSCAR-Bauwerksscanner: Automatisierte Datenaufnahme von Radar, Ultraschall und Wirbelstrom an Spannbetonbauteilen mit bildgebender Darstellung der inneren Konstruktion T2 - DGZfP Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23811 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kipphardt, Heinrich T1 - Non-metal determination - a chalenge in elemental analysis T2 - CCQM IAWG workshop CY - Paris, France DA - 2011-04-13 PY - 2011 AN - OPUS4-23812 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kipphardt, Heinrich A1 - Matschat, Ralf T1 - Special ways to achieve metrological traceability of results in GD-MS and in some other direct solid sampling methods T2 - CCQM IAWG workshop CY - Paris, France DA - 2011-04-13 PY - 2011 AN - OPUS4-23813 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schneider, Rudolf T1 - LC-ELISA uncovers cetirizine - Pharmaceuticals in the environment N2 - A large number of pharmacologically active compounds have been detected in the aquatic environment during the last decade [1] and this gives rise to many concerns [2]. The substances have been disclosed by accident, clever search or elaborate mass spectrometry. Nowadays a broad spectrum of drug parent compounds can be screened for [3], yet the knowledge about the presence of isomers and transformation products (metabolites, conjugates, degradates) is still limited. KW - Immunoassay KW - ELISA KW - Carbamazepin KW - Cetrizin KW - Pharmazeutika KW - Abwasser KW - Oberflächengewässer PY - 2011 SN - 1434-2634 VL - 5-6 SP - 16 EP - 18 PB - GIT Verl. CY - Darmstadt AN - OPUS4-26565 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Deresch, Andreas A1 - Bellon, Carsten A1 - Ewert, Uwe A1 - Jaenisch, Gerd-Rüdiger A1 - Mistral, Q. l. A1 - Gollwitzer, Christian T1 - Simulation Supported POD for RT Test Case - Concept and Modeling T2 - Review of Progress in Quantitative NDE (QNDE 2011) CY - Burlington, VT, USA DA - 2011-07-17 PY - 2011 AN - OPUS4-26660 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Ewert, Uwe A1 - Jechow, Mirko T1 - Concepts for Evalutation of Image Quality in Digital Radiology T2 - Review of Progress in Quantitative NDE (QNDE 2011) CY - Burlington, VT, USA DA - 2011-07-17 PY - 2011 AN - OPUS4-26661 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Ewert, Uwe A1 - Rost, P. A1 - Burch, S.F. T1 - Digital Radiology for Corrosion Inspection and Wall Thickness Measurement of Insulated Pipes T2 - NDT -Konferansen 2011 CY - Bodo, Norway DA - 2011-05-29 PY - 2011 AN - OPUS4-26662 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Ewert, Uwe A1 - Jechow, Mirko T1 - Film replacement in radiographic weld inspection T2 - NDT -Konferansen 2011 CY - Bodo, Norway DA - 2011-05-29 PY - 2011 AN - OPUS4-26663 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jechow, Mirko A1 - Zscherpel, Uwe A1 - Redmer, Bernhard A1 - Ewert, Uwe T1 - Dependence of Signal-to-Noise Ratio on Radiation Energy and Grey Value in Digital Industrial Radiology T2 - International symposium on digital industrial radiology and computed tomography, DIR 2011 der DGZfP CY - Berlin, Germany DA - 2011-06-20 PY - 2011 AN - OPUS4-26664 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Ewert, Uwe A1 - Jechow, Mirko A1 - Bavendiek, K. T1 - Strategies for Film Replacement in Radiography - Appoaches Used in the New Standards T2 - International symposium on digital industrial radiology and computed tomography, DIR 2011 der DGZfP CY - Berlin, Germany DA - 2011-06-20 PY - 2011 AN - OPUS4-26665 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ewert, Uwe A1 - Zscherpel, Uwe A1 - Heyne, Klara A1 - Redmer, Bernhard A1 - Jechow, Mirko T1 - Zum Zusammenhang von Grauwerten und dem normierten und unnormierten Signal/Rausch-Verhältnis in der Digitalen Radiographie - die neue Standart-Prozedur nach ISO/DIS 17636-2 und prEN 14784-2 T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-26667 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hodoroaba, Vasile-Dan T1 - Instrumental performance parameters for specification and check of energy dispersive X-ray spectrometers as in the international standard ISO 15632 N2 - Simple procedures for specifying and checking the performance of energy dispersive X-ray spectrometers (EDS) have been since 2002 available in form of the international standard ISO 15632:2002 [1]. When specifying their spectrometers all major EDS manufacturers refer meanwhile to this standard. Main spectrometer parameters such as energy resolution can be determined as recommended in there. Just several years ago the Si-Li detector has been the mostly widespread type of detector. Since four-five years, silicon drift detector (SDD) EDS providing comparable (in many cases even better) energy resolutions at much higher count rates than the conventional Si-Li’s have got the breakthrough on the market. KW - ED-EPMA KW - WD-EPMA KW - (mu-)XRF KW - EDX PY - 2011 DO - https://doi.org/10.1017/S1431927611003941 SN - 1431-9276 SN - 1435-8115 VL - 17 IS - Suppl. 2 SP - 614 EP - 615 PB - Cambridge University Press CY - New York, NY AN - OPUS4-26750 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Droste, Bernhard A1 - Musolff, André A1 - Müller, Karsten A1 - Quercetti, Thomas T1 - Drop and fire testing of spent fuel and HLW transport casks at 'BAM test site technical safety' N2 - BAM, as a competent German government institute for the mechanical and thermal testing of radioactive material transport and storage containers, operates unique drop and fire test facilities for experimental investigations on the open air BAM Test Site Technical Safety. To be able to perform even drop tests with full scale spent fuel or HAW casks (i.e. the German CASTOR cask designs), BAM constructed in 2004 a large drop test facility capable to handle 200 ton test objects, and to drop them onto a steel plate covered unyielding target with a mass of nearly 2600 ton. Drop test campaigns of the 181 ton GNS CONSTOR V/TC, the 129 ton MHI MSF-69BG and a 1:2 scale model of the GNS CASTOR HAW28M (CASTOR HAW/TB2) have been performed since then. The experimental BAM drop testing activities can be supported also by drop testing of smaller packages (up to 2 ton) in an in-house test facility and by dynamic, guided impact testing of package components and material specimen inside a new drop test machine. In May 2008, a new modern fire test facility was put into operation. The facility provides two test stands fired with liquid propane. Testing in every case has to be completed by computational investigations, where BAM operates appropriate finite element modelling on appropriate computer codes, e.g. ABAQUS, LS-DYNA, ANSYS and other analytical tools. KW - Package testing KW - Drop testing KW - Fire testing KW - Regulations PY - 2011 DO - https://doi.org/10.1179/1746510912Y.0000000002 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 22 IS - 4 SP - 200 EP - 205 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-26691 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Droste, Bernhard A1 - Ulrich, Armin A1 - Borch, Jörg-Peter T1 - Brand new fire test facilities at 'BAM test site technical safety' N2 - Fire testing is an essential part of the hypothetical, cumulative mechanical and thermal accident test conditions that shall guarantee package safety in severe accidents. Not only for radioactive material transport packages but also for other containments of dangerous goods, international standards require specific thermal load specifications. Following the guideline ‘Safety in technology and chemistry' BAM, as a scientific and technical German federal government institute, operates a 12 km² large open air test facility for experimental investigations of dangerous goods and their containments. On an area beside the well-known 200-ton drop test facility, BAM has put into operation a new fire test facility. This facility provides two fire test stands that utilise liquid propane as fuel from a central, earth-covered 60m³ LPG storage tank. From that storage the propane is pumped via pipelines to the test stands where the gas is released from nozzles, and ignited by ignition burners. The fire exposure test facility areas are 12×8 m. Fire test facility B (with gas release nozzles submerged in a water pool) is designed for fire testing of containers that may burst during the test. Fire test facility A (with ring burner systems) is designed for heavy test objects up to 200 tons, e.g. for full-scale spent fuel casks. This paper presents a detailed description of the facility, insight into first tests performed, and results of calorimeter fire tests, using containers of various sizes, to verify the absorbed heat fluxes, demonstrating that regulatory fire test conditions are met, and that the propane fire is equivalent to a kerosene or heating oil pool fire. KW - Thermal testing KW - Fire testing KW - Regulations PY - 2011 DO - https://doi.org/10.1179/1746510911Y.0000000011 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 22 IS - 4 SP - 195 EP - 199 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-26688 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hodoroaba, Vasile-Dan A1 - Salge, T. A1 - Terborg, R. A1 - Rackwitz, Vanessa T1 - Advanced elemental analysis with ED-EPMA, WD-EPMA and mu-XRF at a SEM N2 - It is a latent wish of any SEM/EDS (scanning electron microscope with an energy dispersive spectrometer) analyst to “see more” of the analyzed specimen, i.e. to improve the existing analytical figures of merit. One key issue are the relatively poor limits of detection (not below 0.1 mass-%) provided by energy dispersive X-ray spectrometry (EDX) with the conventional electron excitation (ED-EPMA). This is a consequence of relatively low peak-to-background ratios and reduced energy resolution when compared to wavelength dispersive spectrometry (WD-EPMA). Recent technological developments make possible to equip the SEM with a wavelength dispersive spectrometer (WDS), so that significantly better energy resolution can be attained. Also a relative new product that can be easily attached to a SEM/EDS system is a micro-focus X-ray source. Hence, it is possible to perform (micro-focus) X-ray fluorescence spectrometry (μ-XRF) and take advantage of the enhanced peak-to-background ratios (well suited for trace analysis). However, there are also some disadvantages: an increased measurement time and excitation with a high current in the 10s of nA range are usually required for WDS. μ-XRF provides more bulk information and poor limits of detection for light elements. By combining the advantages of these analytical techniques “seeing more” becomes possible. KW - ED-EPMA KW - WD-EPMA KW - (mu-)XRF KW - EDX PY - 2011 DO - https://doi.org/10.1017/S1431927611003874 SN - 1431-9276 SN - 1435-8115 VL - 17 IS - Suppl. 2 SP - 600 EP - 601 PB - Cambridge University Press CY - New York, NY AN - OPUS4-26751 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hodoroaba, Vasile-Dan A1 - Marinenko, R.B. A1 - Small, J.A. A1 - Unger, Wolfgang T1 - EPMA on copper-gold alloys - a CCQM/SAWG pilot study N2 - CCQM (Consultative Committee for Amount of Substance - Metrology in Chemistry) is an international body of the Meter Convention (BIPM) established as a framework of National Metrology Institutes running inter-laboratory of comparisons to demonstrate the international comparability of chemical measurements, with traceability to international or national reference standards. In 2003 the surface analysis working group (SAWG) was established at CCQM and since then several inter-laboratory comparisons in the field of EPMA have been carried out. In many cases the EPMA results deviated significantly from each other and the expanded uncertainties were greater than expected. Both methods EDS and WDS were employed. However, light elements such as carbon and nitrogen were the major elements analyzed and it is known that the corresponding lowenergy characteristic X-ray lines are more challenging to quantify by EPMA than the higher energy lines of elements with higher atomic numbers. Moreover, the standards selected and their qualities were variable, the quantification models were different, and the acquisition parameters were not specified sufficiently in the analysis instructions. KW - EPMA KW - EDX KW - WDX KW - CCQM KW - Pilot study PY - 2011 DO - https://doi.org/10.1017/S1431927611005150 SN - 1431-9276 SN - 1435-8115 VL - 17 IS - Suppl. 2 SP - 856 EP - 857 PB - Cambridge University Press CY - New York, NY AN - OPUS4-26752 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Case study 2 - Recovery of phosphorus from sewage sludge ashes T2 - Resources that don't cost the earth Workshop CY - Berlin, Germany DA - 2011-12-01 KW - Resources KW - Phosphorus recovery PY - 2011 SP - 17 AN - OPUS4-26930 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mandara, A A1 - Miccoli, Lorenzo A1 - Ferraioli, M A1 - Abruzzese, D. T1 - Seismic assessment of two masonry Medieval bell towers T2 - 5th International Congress "Science and Technology for the Safeguard of Cultural Heritage in the Mediterranean Basin" CY - Istanbul, Turkey DA - 2011-11-22 PY - 2011 AN - OPUS4-26963 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas A1 - Musolff, André A1 - Müller, Karsten T1 - Instrumented Measurements on Radioactive Waste Disposal Containers During Experimental Drop Testing T2 - ICEM 2011 - 14th International Conference on Environment Remediation and Radioactive Waste Management CY - Reims, France DA - 2011-09-25 PY - 2011 AN - OPUS4-26952 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ferraioli, M A1 - Miccoli, Lorenzo A1 - Mandara, A A1 - Abruzzese, D. T1 - Dynamic identification and seismic safety of masonry bell tower T2 - XIV Conference of Seismic Engineering ANIDIS 2011 CY - Bari, Italy DA - 2011-09-18 PY - 2011 AN - OPUS4-27007 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miccoli, Lorenzo A1 - Ferraioli, M A1 - Abruzzese, D. A1 - Di Lauro, G. T1 - Torsional seismic response of an asymmetric-plan hospital building T2 - XIV Conference of Seismic Engineering ANIDIS 2011 CY - Bari, Italy DA - 2011-09-18 PY - 2011 AN - OPUS4-27008 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas A1 - Musolff, André A1 - Müller, Karsten T1 - Instrumented measurements on radioactive waste disposal containers during experimental drop testing N2 - In context with disposal container safety assessment of containers for radioactive waste the German Federal Institute for Materials Research and Testing (BAM) performed numerous drop tests in the last years. The tests were accompanied by extensive and various measurement techniques especially by instrumented measurements with strain gages and accelerometers. The instrumentation of a specimen is an important tool to evaluate its mechanical behavior during impact. Test results as deceleration-time and strain-time functions constitute a main basis for the validation of assumptions in the safety analysis and for the evaluation of calculations based on finite-element methods. Strain gauges are useful to determine the time dependent magnitude of any deformation and the associated stresses. Accelerometers are widely used for the measuring of motion i.e. speed or the displacement of the rigid cask body, vibration and shock events. In addition high-speed video technique can be used to visualize and analyze the kinematical impact scenario by motion analysis. The paper describes some selected aspects on instrumented measurements and motion analysis in context with low level radioactive waste (LLW) container drop testing T2 - ICEM 2011 - 14th International Conference on environmental remediation and radioactive waste management CY - Reims, France DA - 25.09.2011 KW - Drop test KW - Radioactive KW - Disposal container KW - Instrumented measurements PY - 2011 DO - https://doi.org/10.1115/ICEM2011-59142 SP - 929 EP - 938 AN - OPUS4-27044 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Maskos, Michael A1 - Stauber, R.H. ED - Ducheyne, P. ED - Healy, K.E. ED - Hutmacher, D.W. ED - Grainger, D.W. ED - Kirkpatrick, C.J. T1 - Characterization of nanoparticles in biological environments N2 - Deliberate and accidental exposure of the ecosystem including humans to nanoparticles becomes inevitable as nanomaterials are increasingly used. In biological fluids, biomolecules associate with nanoparticles, leading to the formation of a dynamic biomolecule “corona” that critically defines the biological identity of the particle. As the bio-physical properties of such a decorated particle often differ significantly from those of the formulated particle a detailed characterization of nanoparticles in biological environments becomes increasingly important though, nevertheless also technically challenging. Here, we introduce experimental methods currently employed for nanoparticle characterization, present examples underlining the complexity of the nano-bio interface, and discuss the need for further technical and conceptual developments. A deep and mechanistic bio-physical understanding of the nano-bio interface is a challenge but also fundamental prerequisite for future applications in nanobiology, nanomedicine and nano(eco)toxicology. KW - Amorphous silica nanoparticles KW - Dynamic light scattering DLS KW - Interparticle interactions KW - Field-flow fractionation FFF KW - Cryogenic transmission electron microscopy cryo-TEM PY - 2011 SN - 978-0-08-055302-3 VL - 3 IS - Chapter 3.319. SP - 329 EP - 339 PB - Elsevier AN - OPUS4-27283 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dudek, Gabriele T1 - Bericht aus dem Akkreditierungsbeirat: Ermittlungsprozess, ermittelte Regeln und weiteres Vorgehen T2 - 1. Nationale Akkreditierungskonferenz CY - Berlin, Germany DA - 2011-06-08 PY - 2011 AN - OPUS4-27261 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheid, Marc T1 - Praxisbeispiele für Schutzkonzepte: Entstaubungsanlagen - VDI-Richtlinien 2263 Blatt 6 und 6.1 T2 - Technikforum "Sichere Handhabung brennbarer Stäube" des VDI-Wissensforums CY - Düsseldorf, Germany DA - 2011-12-06 PY - 2011 AN - OPUS4-25412 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheid, Marc T1 - Betriebliche und organisatorische Maßnahmen auf dem Gebiet des Staubexplosionsschutzes T2 - Technikforum "Sichere Handhabung brennbarer Stäube" des VDI-Wissensforums CY - Düsseldorf, Germany DA - 2011-12-06 PY - 2011 AN - OPUS4-25413 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter T1 - CFD simulation to predict the performance of a peroxy-fuel burner T2 - 38th National Conference on Fluid Mechanics and Fluid Power CY - Bhopal, India DA - 2011-12-15 PY - 2011 AN - OPUS4-25414 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bretz, Simone A1 - Hagnau, C. A1 - Hahn, Oliver A1 - Ranz, Hans-Jörg T1 - 'Allerhand Loth zu machen' - Das Schwarzlot in der Hinterglasmalerei N2 - Die Befunde eines Forschungsprojektes zur Hinterglasmalerei werfen ein neues Licht auf die gegenseitige Einflussnahme von Glas-, Hinterglas- und Tafelmalerei. Die Autoren veranschaulichen die Forschungsergebnisse, die darauf hinweisen, dass sich vor allem Glasmaler der Hinterglasmalerei annahmen. Zudem zeigen ihre Untersuchungen, dass in der Renaissance und im Mittelalter innerhalb der verschiedenen Malerhandwerke ein enger Austausch existierte. KW - Archäometrie KW - Zerstörungsfreie Prüfung KW - Kunst- und Kulturgut PY - 2011 SN - 0933-4017 VL - 8 SP - 27 EP - 39 PB - Callwey CY - München AN - OPUS4-25419 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shcheglov, Pavel A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael A1 - Uspensky, S.A. A1 - Petrovsky, V.N. T1 - Study of welding plume in high-power fiber laser welding T2 - LTWMP '11 - 5th International conference "Laser technologies in welding and materials processing" CY - Crimea, Ukraine DA - 2011-05-24 PY - 2011 SP - 142 EP - 147 AN - OPUS4-25473 LA - rus AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quiroz Penaranda, Vanessa A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Investigations on laser beam welding of high-manganese austenitic and austenitic-ferritic stainless steels N2 - Influence of the main laser welding parameters on process stability and resulting weld quality were investigated. Effects of weld edge preparation on the weld appearance and quality were considered. The obtained welded joints were subjected to radiographic tests for detection of internal imperfections. Metallurgical characterisation of the samples regarding the resulting phase composition and hardness was conducted. Tensile and potentiodynamic tests were performed to evaluate the mechanical and corrosion properties. The results provide an insight into the advantages and limitations of the laser welding process for joining high-manganese alloyed stainless steels. Conditions for the production of defect-free and corrosion-resistant welds having good mechanical properties could be determined. T2 - LTWMP '11 - 5th International conference "Laser technologies in welding and materials processing" CY - Crimea, Ukraine DA - 24.05.2011 PY - 2011 SP - 55 EP - 59 AN - OPUS4-25475 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Denkler, Tilman T1 - Management of Technical Cooperation Projects - Opportunities and Limitations of IT-Solutions T2 - BAM Sonderkolloquium Internationaler Technologietransfer CY - Berlin, Germany DA - 2011-12-08 PY - 2011 AN - OPUS4-25478 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Torge, Manfred A1 - Adam, Karin A1 - Feldmann, Ines T1 - Naturwissenschaftliche Untersuchungen an Glasproben aus Mühlhausen N2 - Die Bestimmung der chemischen Zusammensetzung von Glasproben, insbesondere von historischen Glasmalereien, gehört seit mehr als 20 Jahren zu den Standardverfahren in der Arbeitsgruppe 4.21 »Umwelteinflüsse und Schädigungsmechanismen« der BAM. Während in den 1990er Jahren eine Elektronenstrahlmikrosonde für diese Analysen zur Verfügung stand, werden seit etwa zehn Jahren solche Untersuchungen mit einem Environmental Scanning Electron Microscope (ESEM) durchgeführt. KW - Glasmalerei KW - Glasanalysen KW - EDX PY - 2011 SN - 978-3-937940-77-9 N1 - Serientitel: Arbeitshefte des Thüringischen Landesamtes für Denkmalpflege und Archäologie – Series title: Arbeitshefte des Thüringischen Landesamtes für Denkmalpflege und Archäologie VL - 38 SP - 96 EP - 97 PB - Sandstein CY - Dresden AN - OPUS4-25483 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Beke, S. A1 - Sugioka, K. A1 - Midorikawa, K. A1 - Bonse, Jörn ED - Hemsworth, E.J. T1 - Nanosecond and femtosecond laser ablation of TeO2 crystals: surface characterization and plasma analysis N2 - Near-IR femtosecond (fs) (pulse duration = 150 fs, wavelength = 775 um, Repetition rate 1 kHz) and VUV nanosecond (ns) (pulse duration = 20 ns, wavelength = 157 nm, repetition rate 1 to 5 Hz) laser pulse ablation of single-crystalline TeO? (c-Te02) surfaces was performed in air using the direct focusing technique. A multi-method characterization using optical microscopy, atomic force microscopy and scanning electron microscopy revealed the surface morphology of the ablated craters. This allowed us at each irradiation site to characterize precisely the lateral and vertical dimensions of the laser-ablated craters for different laser pulse energies and number of laser pulses per spot. Based on the obtained information, we quantitatively determined the Ablation threshold fluence for the fs laser irradiation when different pulse numbers were applied to the same spot using two independent extrapolation techniques. We found that in the case of NIR fs laser pulse irradiation, the ablation threshold significantly depends on the number of laser pulses applied to the same spot indicating that incubation effects play an important role in this material. In the case of VUV ns laser pulses, the ablation rate is significantly higher due to the high photon energy and the predominantly linear absorption in the material. These results are discussed on the basis of recent models of the interaction of laser pulses with dielectrics. In the second part of this chapter, we use timeof-flight mass spectrometry (TOFMS) to analyze the elemental composltion of the ablation products generated upon laser irradiation of c-Te02 with single fs- (pulse duration ~ 200 fs, wavelength 398 nm) and ns-pulses (pulse duration 4 ns, wavelength 355 nm). Due to the three Order of magnitude different peak intensities of the ns- and fs laser pulses, significant differences were observed regarding the laser-induced species in the plasma plume. Positive singly, doubly and triply charged Te ions (Te+, Te2+, Te3+) in the form of many different isotopes were observed in case of both irradiations. In the case of the ns-laser ablation, the TeO+ formation was negligible compared to the fs case and there was no Te trimer (Te3+) formation observed. It was found that the amplitude of Te ion Signals strongly depends on the applied laser pulse energy. Singly charged Oxygen ions (0+) are always present as a byproduct in both kinds of laser ablation. KW - Femtosecond laser ablation KW - Nanosecond laser ablation KW - Damage threshold KW - TeO2 KW - Dielectrics KW - Time-of-flight mass spectrometry (TOF-MS) PY - 2011 SN - 978-1-61324-851-5 N1 - Serientitel: Physics Research and Technology – Series title: Physics Research and Technology IS - Chapter 4 SP - 77 EP - 96 PB - Nova Science Publishers, Inc. AN - OPUS4-25465 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Boenke, Viola A1 - Schwibbert, Karin A1 - Kunte, Hans-Jörg A1 - Gorbushina, Anna A1 - Bücker, Michael A1 - Feldmann, Ines A1 - Heidrich, Gabriele A1 - Sabel, Martin A1 - Haag, R. T1 - Besiedelbarkeit von Biomaterialien durch Bakterien T2 - Life Science Day - Zukunftsort Dahlem CY - Berlin, Germany DA - 2011-08-26 PY - 2011 AN - OPUS4-25331 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - von Gablenz, C.-H. A1 - Spaltmann, Dirk T1 - Das CargoLifter-Ballonkransystem N2 - Das CargoLifter-Ballonkransystem nutzt die Prinzipien der Leichter-als-Luft-Technologie für das Heben von Gütern. Der mit leichtem Gas gefüllte Ballon drängt in der schwereren Luft nach oben und kann somit Lasten anheben. Im Gegensatz zu erdgebundenen Kranen ist für den Luftkran die Beschaffenheit des Bodens sekundär. Der Ballonkran wird an 3 Winden verankert und über die im Kranknotenpunkt zusammengeführten Seile präzise gesteuert. Beim Heben und Versetzen verbleibt die Last unter dem Ballon, der stets 100 % seiner Hubkraft auch bis zu 200 m Höhe und selbst weiterem Versatz behält. Reichweite bedeutet beim CargoLifter-Ballonkransystem statt mehr Ausleger mehr Seil. PY - 2011 SN - 1866-0207 VL - 123 IS - 12 SP - 34 EP - 38 PB - E. Schmidt, Süddt. Zweigstelle CY - München AN - OPUS4-25332 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schwibbert, Karin A1 - Kunte, Hans-Jörg A1 - Heidrich, Gabriele A1 - Bagyan, I. A1 - Lentzen, G. A1 - Marin-Sanguino, A. A1 - Oesterhelt, D. A1 - Pfeiffer, F. A1 - Klenk, H.-P. T1 - Vom Genom zum Produkt: Industielle Produktion von Zellschutzstoffen mit salzliebenden Bakterien T2 - Life Science Day - Zukunftsort Dahlem CY - Berlin, Germany DA - 2011-08-26 PY - 2011 AN - OPUS4-25333 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trommsdorf, Stephan T1 - Marktaufsichtsprogramme der Mitgliedstaaten T2 - 1. Jahrestagung Marktüberwachung Baden-Württemberg CY - Herrenberg, Germany DA - 2011-12-14 PY - 2011 AN - OPUS4-25334 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas A1 - Boehm, Rainer A1 - Gohlke, Dirk A1 - Völz, Uwe T1 - Analyseprüfung von Eisenbahnradsatzwellen mit Ultraschall T2 - DGZFP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-25335 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kotschate, Daniel A1 - Gohlisch, Stephan A1 - Heckel, Thomas A1 - Sondermann, F. T1 - Bildgebende Ultraschallhandprüfeinrichtung für die Ausbildung T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-25336 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas A1 - Boehm, Rainer A1 - Gohlke, Dirk T1 - Optimierung von Ultraschall-Fokusprüfköpfen beim Einsatz an stark gekrümmten Oberflächen T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-25337 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gohlke, Dirk A1 - Kotschate, Daniel A1 - Heckel, Thomas T1 - Visualisierung der Volumenmessdaten von hochauflösenden Ultraschalltauchtechnikprüfungen T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-25338 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koch, Matthias A1 - Merkel, Stefan A1 - Maul, Ronald A1 - Köppen, Robert T1 - Schimmelpilzgifte in Lebensmitteln - Analytik und Referenzmaterialien als Beitrag der BAM zur Lebensmittelsicherheit T2 - BAM-Kolloquium CY - Berlin, Germany DA - 2011-10-19 PY - 2011 AN - OPUS4-25339 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterloh, Kurt A1 - Wrobel, Norma A1 - Ewert, Uwe A1 - Krstelj, V. A1 - Zvizdic, D. ED - Ender, J. ED - Fiege, J. T1 - Detection technologies - common concepts in security and safety T2 - Future Security 2011 Conference CY - Berlin, Germany DA - 2011-09-05 KW - Technical safety and public security KW - Bridging separate competence areas PY - 2011 SN - 978-3-8396-0295-9 SP - 125 EP - 127 CY - Berlin AN - OPUS4-25354 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wrobel, Norma A1 - Osterloh, Kurt A1 - Zscherpel, Uwe A1 - Ewert, Uwe ED - Ender, J. ED - Fiege, J. T1 - Variable irradiation geometry with a nex X-ray backscatter camera for security applications T2 - Future Security 2011 Conference CY - Berlin, Germany DA - 2011-09-05 KW - Technical safety and public security KW - Bridging separate competence areas PY - 2011 SN - 978-3-8396-0295-9 SP - 128 EP - 131 CY - Berlin AN - OPUS4-25355 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weber, Mike A1 - Wille, Frank A1 - Ballheimer, Viktor A1 - Musolff, André T1 - From experiment to appropriate finite element model-safety assessment for ductile cast iron casks demonstrated by means of IAEA puncture drop test N2 - In the approval procedure of transport packages for radioactive materials, the competent authority mechanical and thermal safety assessment is carried out in Germany by BAM Federal Institute for Materials Research and Testing. The combination of experimental investigations and numerical calculations in conjunction with materials and components testing is the basis of the safety assessment concept of the BAM. Among other mechanical test scenarios, a 1 metre drop test onto a steel bar has to be considered for the application of the hypothetical accident conditions to Type B packages according to IAEA regulations. Within the approval procedure for the new German package design of the HLW cask CASTOR® HAW 28M, designed by GNS Gesellschaft für Nuklear-Service Germany, a puncture drop test was performed with a half-scale model of the cask at -40°C. For independent assessment and to control the safety analysis presented by the applicant, BAM developed a complex finite element (FE) model for a dynamical ABAQUS/ExplicitTM analysis. This paper describes in detail the use of the FE method for modelling the puncture drop test within an actual assessment strategy. At first, investigations of the behaviour of the steel bar were carried out. Different friction coefficients and the material law of the bar were analysed by using a 'rigid-body' approximation for the cask body. In the next step, a more detailed FE model with a more realistic material definition for the cask body was developed. The validation of calculated strains was carried out by comparison with the results of the strain gauges located at the relevant points of the cask model. The influence of the FE meshing is described. Finally, the validated FE half-scale model was expanded to full-scale dimension. Scaling effects were analysed. The model was used for safety assessment of the package to be approved. KW - IAEA puncture drop test KW - Cylindrical cask KW - Explicit dynamics KW - Scaled model KW - Numerical analysis KW - Validation KW - Safety assessment PY - 2011 DO - https://doi.org/10.1179/1746510911Y.0000000010 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 22 IS - 3 SP - 148 EP - 153 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-25356 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaenisch, Gerd-Rüdiger A1 - Deresch, Andreas A1 - Bellon, Carsten A1 - Ewert, Uwe A1 - Przybilla, Waldemar ED - Thompson, D.O. ED - Chimenti, D.E. T1 - Measurement and modeling of scatter ratios at high energies N2 - Determining scatter ratios at high energies (> ~ 1MeV) presents challenges not immediately obvious from measurements at conventional X-ray energies. This includes reduced attenuation even in heavy elements as well as a stronger forward bias of scattering. In order to check the reliability of different measurement setups with regard to material thicknesses, distances, and collimation, attenuation and scattering were separately simulated using a Monte Carlo model. The simulation results help in understanding the sources of radiation scattered into the detection area, thereby aiding in eliminating undesired contributions. T2 - 37th Annual Review of Progress in Quantitative Nondestructive Evaluation CY - San Diego, CA, USA DA - 18.07.2010 KW - Radiography KW - Optimisation KW - X-ray detection KW - Simulation KW - High energy KW - Co-60 KW - Modeling KW - Scatter PY - 2011 SN - 978-0-7354-0888-3 DO - https://doi.org/10.1063/1.3591895 SN - 0743-0760 SN - 0094-243X N1 - Serientitel: AIP conference proceedings – Series title: AIP conference proceedings IS - 1335 SP - 517 EP - 524 PB - American Institute of Physics CY - Melville, NY AN - OPUS4-25358 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Development of Repair Mortars for the Restoration and Reprofiling of Natural Stone Elements in Listed Buildings and Monuments T2 - 16th International Conference on Composite Structures (ICCS16) CY - Oporto, Portugal DA - 2011-06-28 PY - 2011 AN - OPUS4-25400 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfennig, Anja A1 - Linke, Barbara A1 - Kranzmann, Axel T1 - Corrosion behavior of pipe steels at the CCS-site Ketzin, Germany T2 - 10. Technologietransfertrag CY - Wildau, Germany DA - 2011-06-22 PY - 2011 AN - OPUS4-25492 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reich, Franziska A1 - Pötzsch, Klaus-Michael T1 - Der Einsatz von Sicherheitsventilen an Transportbehältern T2 - Transport Logistic 2011 CY - Munich, Germany DA - 2011-04-10 PY - 2011 AN - OPUS4-25493 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reich, Franziska A1 - Pötzsch, Klaus-Michael T1 - BAM-Kolloquium T2 - BAM Berlin UE, BAM CY - Berlin, Germany DA - 2011-04-13 PY - 2011 AN - OPUS4-25494 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kranzmann, Axel A1 - Ruhl, Aki Sebastian A1 - Saliwan Neumann, Romeo T1 - Comparative Identification of Corrosion Products under CCD Conditions by Simulated Acid Droplet Corrosion T2 - IEA 2nd Oxyfuel Combustion Conference CY - Yeppoon, Australia DA - 2011-09-12 PY - 2011 AN - OPUS4-25499 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gaft, M. A1 - Nagli, L. A1 - Gornushkin, Igor B. A1 - Groisman, Y. T1 - Doubly ionized ion emission in laser-induced breakdown spectroscopy in air N2 - The emission from doubly ionized species in laser-induced plasmas has not been properly investigated before since most analytical measurements were made at relatively long delays. This work proves that doubly ionized species, such as boron (B) III and iron (Fe) III, can exist during the first 150–200 ns of the plasma lifetime in plasmas produced in air by typical lasers with irradiances of 109 1011 W/cm². The emission from these ions was detected using both the double- and single-pulse excitations. The sum of the second ionization potential and the energy of corresponding excited states is approximately 30 eV. The presence of doubly charged ions in the early plasma was additionally confirmed by computer simulations using a collision-dominated plasma model. The Emission from doubly ionized species may be used for analytical purpose. For example, in the spectrum from a B–Fe ore, the B III analytical line at 206.6 nm is free from Fe spectral interference thus enabling the online laser-induced breakdown spectroscopy sorting of ores into three products with high, medium, and low B2O3 contents. KW - Plasma KW - Double ionization KW - Boron KW - Iron KW - Online KW - Sorting PY - 2011 DO - https://doi.org/10.1007/s00216-011-4847-0 SN - 1618-2642 SN - 1618-2650 VL - 400 IS - 10 SP - 3229 EP - 3237 PB - Springer CY - Berlin AN - OPUS4-25825 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Shabanov, Sergej V. A1 - Gornushkin, Igor B. T1 - Emission plasma tomography with large acceptance angle apertures relevant to laser induced plasma spectroscopy N2 - It is proposed to use apertures with large acceptance angles to reduce the integration time when studying the emissivity of laser induced plasmas by means of the Abel inversion method. The spatial resolution lost due to contributions of angled lines of sight to the intensity data collected along the plasma plume diameter is restored by a special numerical data processing. The procedure is meant for the laser induced plasma diagnostics and tomography when the integration time needed to achieve a reasonable signal to noise ratio exceeds a characteristic time scale of the plasma state variations which is short especially at early stages of the plasma evolution. It can also be used to improve the spatial resolution in a conventional experimental setup for plasma diagnostics. KW - Abel inversion KW - LIBS KW - Plasma tomography PY - 2011 DO - https://doi.org/10.1016/j.sab.2011.04.006 SN - 0584-8547 SN - 0038-6987 VL - 66 IS - 6 SP - 413 EP - 420 PB - Elsevier CY - Amsterdam AN - OPUS4-25827 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böllinghaus, Thomas A1 - Mente, Tobias T1 - Vermeidung von Rissen beim Schweissen von Rohrleitungen N2 - Schadensfälle in den letzten zehn Jahren mit teilweise katastrophalen Folgen belegen, dass der Vermeidung von Rissen beim Schweißen von Rohrleitungen besondere Aufmerksamkeit zu schenken ist. In der Analyse solcher Schäden ist zu unterscheiden, ob die Risse bereits während oder kurz nach der schweißtechnischen Fertigung der Rohrkomponenten oder während des anschließenden Betriebes entstanden sind. Im vorliegenden Beitrag wird sich vor allem auf die Vermeidung einer Heiß- und Kaltrissbildung beim Schweißen von Rohrleitungen konzentriert und es werden weitere Forschungsperspektiven abgeleitet. T2 - DVM-Tag 2011 - Bauteilzuverlässigkeit - Schäden und ihre Vermeidung CY - Berlin, Germany DA - 04.05.2011 KW - Rissvermeidung KW - Heißrissbildung KW - Wasserstoffunterstützte Kaltrissbildung (HACC) KW - Pipelineschweißungen PY - 2011 SN - 0946-5987 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 678 SP - 81 EP - 90 AN - OPUS4-26113 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böllinghaus, Thomas A1 - Mente, Tobias A1 - Dabah, Eitan ED - Kulkarni, D.V. ED - Samant, M. ED - Krishnan, S. ED - De, A. ED - Krishnan, J. ED - Patel, H. ED - Bhaduri, A.K. T1 - Trends in investigating hydrogen cracking and diffusion in steel welds N2 - The present contribution highlights recent trends in investigating hydrogen diffusion and cracking in steel welds. For such studies, supermartensitic stainless steels (SMSS) have exemplarily been selected. These materials have been used for offshore and marine constructions for about two decades now. They present a versatility of improved properties such as high strength to thickness ratio, good weldability and good corrosion resistance. However, as shown by respective failure cases, SMSS welds might become prone to hydrogen assisted cracking and the degradation phenomena are more easily to investigate due to the nearly homogeneous martensitic microstructure than in other materials. Generally, it has to be distinguished between cracking that occurs during or shortly after fabrication welding, or during subsequent operation of SMSS components. In order to achieve crack avoidance during fabrication and service, conclusive test sequences have to be applied, ranging from field tests at real components and full scale tests investigating the materials behavior under real service conditions to basic and small scale tests, such as tensile and corrosion tests, oriented more towards a materials ranking. Considerable testing of SMSS welds has been carried out and the present paper particularly summarizes spotlights on 1:1 scale component testing of welded tubulars, slow strain rate testing and basic tests oriented to elucidate the hydrogen behavior and degradation in SMSS weld microstructures. Also, permeation tests, hydrogen dependent degradation of mechanical properties and thermal desorption spectroscopy are adressed. As a specific item, first results of lately conducted investigations for tracking hydrogen movement in such weld microstructures by using high energy synchrotron radiation are elucidated. T2 - IIW International conference on global trends in joining, cutting and surfacing technology CY - Chennai, India DA - 21.07.2011 PY - 2011 SN - 978-81-8487-152-4 SP - 49 EP - 55 PB - Narosa Publ. House AN - OPUS4-26114 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lindner, H. A1 - Loper, K.H. A1 - Hahn, D.W. A1 - Niemax, Kay T1 - The influence of laser-particle interaction in laser induced breakdown spectroscopy and laser ablation inductively coupled plasma spectrometry N2 - Particles produced by previous laser shots may have significant influence on the analytical signal in laser-induced breakdown spectroscopy (LIBS) and laser ablation inductively coupled plasma (LA-ICP) spectrometry if they remain close to the position of laser sampling. The effects of these particles on the laser-induced breakdown event are demonstrated in several ways. LIBS-experiments were conducted in an ablation cell at atmospheric conditions in argon or air applying a dual-pulse arrangement with orthogonal pre-pulse, i.e., plasma breakdown in a gas generated by a focussed laser beam parallel and close to the sample surface followed by a delayed crossing laser pulse in orthogonal direction which actually ablates material from the sample and produces the LIBS plasma. The optical emission of the LIBS plasma as well as the absorption of the pre-pulse laser was measured. In the presence of particles in the focus of the pre-pulse laser, the plasma breakdown is affected and more energy of the pre-pulse laser is absorbed than without particles. As a result, the analyte line emission from the LIBS plasma of the second laser is enhanced. It is assumed that the enhancement is not only due to an increase of mass ablated by the second laser but also to better atomization and excitation conditions favored by a reduced gas density in the pre-pulse plasma. Higher laser pulse frequencies increase the probability of particle-laser interaction and, therefore, reduce the shot-to-shot line intensity variation as compared to lower particle loadings in the cell. Additional experiments using an aerosol chamber were performed to further quantify the laser absorption by the plasma in dependence on time both with and without the presence of particles. The overall implication of laser-particle interactions for LIBS and LA-ICP-MS/OES are discussed. KW - Laser-particle interaction KW - LIBS KW - LA-ICP spectrometry PY - 2011 DO - https://doi.org/10.1016/j.sab.2011.01.002 SN - 0584-8547 SN - 0038-6987 VL - 66 IS - 2 SP - 179 EP - 185 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-26077 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Burkert, Andreas A1 - Fischer, Joachim A1 - Zietelmann, Christina A1 - Lehmann, Jens T1 - Sauber! - Erhaltung des Korrosionsschutzes bei 'rostfreiem Stahl' N2 - Es ist mittlerweile eine zunehmend bekannte Tatsache, dass „nichtrostende“ Stähle trotz ihres Namens rosten können. Werden die spezifischen Besonderheiten und Anforderungen, die sich beim Einsatz nichtrostender Stähle ergeben, aus Unkenntnis oder Nachlässigkeit nicht beachtet, kann dies zu unerwarteten Korrosionserscheinungen und auch zum funktionalen Versagen von Konstruktionen führen. Im Folgenden wird dargestellt, dass nichtrostende Stähle nur dann korrosionsbeständig bleiben, wenn auch Reinigung und Pflege der Oberflächen mehr Beachtung finden. Bereits in der Planungsphase, spätestens aber bei der Ausführung muss klar sein, wie mit den Oberflächen urngegangen werden soll, um ihre positiven Eigenschaften zu erhalten. Nicht zuletzt müssen auch die Betreiber und Nutzer wissen, dass nichtrostende Stähle in vielen Bereichen erheblichen Pflege- und Erhaltungsbedarf haben. KW - Nichtrostender Stahl KW - Austenit KW - Ferrit KW - Lean Duplex KW - Korrosionsverhalten PY - 2011 VL - III SP - 9 EP - 14 PB - Bernheine AN - OPUS4-26059 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bertovic, Marija A1 - Gaal, Mate A1 - Müller, Christina A1 - Fahlbruch, B. T1 - Investigating human factors in manual ultrasonic testing: testing the human factors model N2 - The human factors approach relies on understanding the properties of human capability and limitations under various conditions and the application of that knowledge in designing and developing safe systems. Following the principles of the MTO (Man Technology Organisation) approach, emphasis should be given to the way people interact with technical as well as organisational systems. A model describing human factor influences in relation to the performance shaping factors and their effect on manual ultrasonic inspection performance had been built and a part of it empirically tested. The experimental task involved repeated inspection of 18 defects according to the standard procedure under no, middle and high time pressure. Stress coping strategies, the mental workload of the task, stress reaction and organisational factors have been measured. The results have shown that time pressure, mental workload and experience influence the quality of the inspection performance. Organisational factors and their influence on the inspection results were rated as important by the operators. However, further research is necessary into the effects of stress. KW - Human factors KW - Manual ultrasonic testing KW - In-service inspection KW - Nuclear power plants KW - Time pressure PY - 2011 DO - https://doi.org/10.1784/insi.2011.53.12.673 SN - 0007-1137 VL - 53 IS - 12 SP - 673 EP - 676 PB - British Institute of Non-Destructive Testing CY - Northampton AN - OPUS4-26083 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hothan, Sascha T1 - Grundlagen zur Erweiterung des Anwendungsbereiches für reaktive Brandschutzsysteme auf Stahlbauteilen im nationalen Zulassungsverfahren N2 - Die hier vorgestellten Untersuchungen dienen der Erweiterung des Anwendungsbereiches für reaktive Brandschutzsysteme auf Stahlbauteilen im nationalen Zulassungsverfahren. Für die Wirksamkeit reaktiver Brandschutzsysteme ist die Haftfähigkeit der reaktiven Brandschutzbeschichtung auf dem Untergrund (Stahl) von entscheidender Bedeutung. Die Haftfähigkeit der Beschichtung ist neben der Oberflächenbeschaffenheit und den Eigenschaften des reaktiven Systems selbst im Wesentlichen von der Form des Bauteils und den sich im Brandfall einstellenden erformungen (Krümmungen und Dehnungen) abhängig. KW - Reaktive Brandschutzsysteme KW - Zugstäbe KW - FEM-Berechnungen PY - 2011 DO - https://doi.org/10.1002/dibt.201130046 SN - 1438-7778 SN - 1437-0964 VL - 42 IS - 6 SP - 187 EP - 189 PB - Ernst CY - Berlin AN - OPUS4-26099 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Staude, Andreas A1 - Neukamm, M. T1 - Bestimmen der geometrischen Eigenschaften industrieller CT T2 - Oldenburger 3D-Tage 2011 CY - Oldenburg, Germany DA - 2011-02-01 PY - 2011 AN - OPUS4-26125 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schwarz, G. A1 - Weller, Michael G. A1 - Beck, S. A1 - Schuschke, K. A1 - Linscheid, M. A1 - Schalley, C. A. T1 - MeCAT - Identification and quantification of proteins in human serum T2 - Annual meeting DGMS CY - Dortmund, Germany DA - 2011-09-21 PY - 2011 AN - OPUS4-26040 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hothan, Sascha A1 - Ehlig, D. T1 - Reinforced concrete slabs strengthened with textile reinforced concrete subjected to fire T2 - Concrete Spalling due to Fire exposure, Proceedings of the 2nd International RILEM Workshop CY - Delft, Netherlands DA - 2011-10-05 PY - 2011 AN - OPUS4-26046 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Döring, Joachim A1 - Bartusch, Jürgen A1 - Bovtun, V. A1 - Brekow, Gerhard A1 - Kreutzbruck, Marc T1 - Charakterisierung der Wandler für Luftultraschallprüfung aus zellulärem Polypropylen-Ferroelektret N2 - In den letzten Jahren stieg die Anfrage für zerstörungsfreie Prüfung (ZIP) mit Luftultraschall deutlich. Die klassische ZfP mit Ultraschall nutzt Flüssigkeiten als Koppelmittel zwischen dem Wandler und dem Prüfkörper. Für die Prüfung von Gegenständen mit empfindlicher Oberfläche, die das Koppelmittel beschädigen oder verunreinigen kann, ist deswegen Luftultraschall besser geeignet. Eine mögliche Anwendung ist beispielsweise der Nachweis von Delaminationen in glas- und kohlefaserverstärkten Verbundwerkstoffen sowie Sandwichbauteilen, die in der Luftfahrt- und der Automobilindustrie eingesetzt werden. T2 - DAGA 2011 - 37. Jahrestagung für Akustik - Fortschritte der Akustik CY - Dusseldorf, Germany DA - 21.03.2011 KW - Luftultraschall KW - Wanderfolien KW - Zelluläres Polypropylen KW - Akustische Impedanz KW - Signal-Rausch-Anstand PY - 2011 SN - 978-3-939296-02-7 SP - 337 EP - 338 AN - OPUS4-26403 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Döring, Joachim A1 - Bartusch, Jürgen A1 - Beck, Uwe A1 - Weise, Matthias A1 - Bovtun, Viktor Petrovic A1 - Brekow, Gerhard A1 - Kreutzbruck, Marc T1 - Parameter reproducibility of polypropylene ferroelectret transducers for air-coupled ultrasonic testing N2 - The extremely low acoustic impedance of polypropylene ferroelectret combined with its piezoelectric properties makes this material suitable for construction of aircoupled ultrasonic transducers for non-destructive testing. For the fabrication of transducers with a stable quality, the reproducibility of their key parameters is of interest. The reproducibility was evaluated by means of (i) impedance spectroscopy and (ii) pulse-echo measurements. (i) Impedance spectroscopy was applied to identify the resonance frequency, the coupling factor and the acoustic impedance of several nominally identical transducers. (ii) Pulse-echo measurements yielded the signal form of these transducers. The variation of the signal amplitude measured with pulseecho technique was about 10 dB. A part of this variation Comes from the deposition of transducer electrodes and another part from local variations of ferroelectret properties. The variation of the signal amplitude was caused by the observed variation of the coupling factor, which was also about 10 dB. The variation of the acoustic impedance was only about 1 dB, thus having no effect on the variation of the signal amplitude. These results indicate that the variability can be reduced by improving the control of electrode deposition and by optimizing the production technology affecting the reproducibility of material properties. T2 - 2011 IEEE International ultrasonics symposium (IUS) CY - Orlando, FL, USA DA - 18.10.2011 KW - Air-coupled ultrasonic transducers KW - Polypropylene ferroelectret KW - Reproducibility PY - 2011 IS - Abstract-ID 258 SP - 1 EP - 3 AN - OPUS4-26405 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Komann, Steffen A1 - Neumann, Martin A1 - Ballheimer, Viktor A1 - Wille, Frank A1 - Weber, Mike A1 - Qiao, Linan A1 - Droste, Bernhard T1 - Mechanical assessment within type B packages approval: application of static and dynamic calculation approaches N2 - This paper demonstrates exemplarily how numerical and experimental approaches can be combined reasonably in mechanical assessment of package integrity according to the IAEA regulations. The paper also concentrates on the question about how static mechanical approaches can be applied, and what their problems are in relation to dynamic calculation approaches. Under defined impact tests, which represent accident transport conditions, the package has to withstand impact loading, e.g. resulting from a 9 m free drop onto an unyielding target in sequence with a 1 m puncture drop test. Owing to the local character of the interaction between the puncture bar and the cask body, it is possible to develop a dynamic numerical model for the 1 m puncture drop which allows an appropriate simulation of the interaction area. Results from existing experimental drop tests with prototype or small scale cask models can be used for verification and validation of applied analysis codes and models. The link between analysis and experimental drop testing is described exemplarily by considering a regulatory 1 m puncture bar drop test onto the cask body of a recently approved German high level waste transport package. For the 9 m drop test of the package, it is difficult to develop a dynamic numerical model of the package due to the complexity of the interaction between cask body, impact limiters and unyielding target. Dynamic calculations require an extensive verification with experimental results. The simulation of a 9 m drop of a package with impact limiters is thereby often more complex than the simulation of a 1 m puncture drop onto the cask body. A different approximation method can be applied for the consideration of dynamic effects on the impact loading of the package. In a first step, maximum impact force and rigid body deceleration of the cask body during the impact process can be calculated with simplified numerical tools. This rigid body deceleration can subsequently be applied on a verified static numerical model. Dynamic effects, which cannot be covered by the static numerical analysis, have therefore to be considered by using an additional dynamic factor. The paper describes this approach exemplarily for a 9 m horizontal drop of a typical spent fuel cask design. KW - Package assessment KW - Package KW - Packaging KW - Structural analysis PY - 2011 DO - https://doi.org/10.1179/1746510911Y.0000000012 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 22 IS - 4 SP - 179 EP - 183 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-26448 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian T1 - Failure criterion based on adhesion for composites under transverse loading N2 - The failure of laminates usually is initiated by the failure of the plies with the maximum transverse stresses. The failure of those plies generally reduces the load carrying capability of the laminate, even though they carry only a small part of the external load. The analysis of failure under off-axis stresses accordingly is essential for the prediction of the strength of laminates. This is taken into account in the "mechanisms based failure criteria" e.g. by Puck. Most of these inter fiber failure criteria are not based on the micromechanics of the failure process but on prescribed stress interaction functions. The failure of plies under transverse loading obviously is governed by the bond strength between fiber and matrix fiber. The interfacial debonding was studied e.g. by Paris et al. and Corea et al.. The bond strength between fiber and matrix usually is measured by using micromechanical tests e.g. pull-out, push-out or fragmentation tests. Stress analyses as well as fracture mechanical analyses show that the interfacial failure over a large range is dominated by shear stresses (Kim and Mai, Pisanova et al, Marotzke and Qiao). The stress distribution arising in those experiments however differs from the stresses acting in a lamina under transverse loading. In transverse failure of a lamina, radial stresses as well as shear stresses are dominating the failure process of the interface. In addition longitudinal shear stresses are present. Experimental work concerning off-axis loading of single fibers was done e.g. by Tandon and Kim and by Ogihara and Koyanagi. They studied the influence of the fiber alignment by using a specimen in form of a cruciform with skew wings. T2 - Thermosets 2011 - From monomers to components - 2nd international conference on thermosets CY - Berlin, Germany DA - 21.09.2011 KW - Composites KW - Strength KW - Adhesion KW - Fracture mechanics PY - 2011 SN - 978-3-8396-0312-3 SP - 86 EP - 88 PB - Fraunhofer Verlag CY - Berlin AN - OPUS4-26451 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna T1 - MODEL ROCK BIOFILM: GENETIC AND MICROBIOLOGICAL EXPERIMENTS: Fungal growth on bare rock surfaces - where does the carbon come from? T2 - Fourth meeting of the ISHAM working groups on Black Yeasts and chromoblastomycosis: “Hidden Danger, Bright Promise” CY - Curitiba, Brazil DA - 2011-12-01 PY - 2011 AN - OPUS4-26468 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna A1 - Noack-Schönmann, Steffi A1 - Bus, Tanja A1 - Nai, Corrado A1 - Schneider, Lucienn A1 - Banasiak, Ronald T1 - DNA EXTRACTION METHODS, AS WELL AS GENOME ANALYSIS OF SEVERAL BLACK FUNGI :Genomic and molecular characterization of a model ascomycete ancestral to mutualistic and pathogen-rich fungal lineages (A95 Sarcinomyces petricola, Chaetothyriales) T2 - Fourth meeting of the ISHAM working groups on Black Yeasts and chromoblastomycosis: “Hidden Danger, Bright Promise” CY - Curitiba, Brazil DA - 2011-12-01 PY - 2011 AN - OPUS4-26469 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna A1 - Nai, Corrado A1 - Pannenbecker, Annette Cecilia A1 - Noack-Schönmann, Steffi A1 - Broughton, William J. T1 - Nutritional physiology of Sarcinomyces petricola A95, a model black fungus to study primary successions in terrestrial ecosystems T2 - Fourth meeting of the ISHAM working groups on Black Yeasts and chromoblastomycosis: “Hidden Danger, Bright Promise” CY - Curitiba, Brazil DA - 2011-12-01 PY - 2011 AN - OPUS4-26470 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachsmuth, Janne T1 - Wellenform basierte Quellenlokalisierung im Vergleich zu konventionellen Methoden T2 - 18. Kolloquium Schallemission CY - Wetzlar, Germany DA - 2011-10-27 PY - 2011 AN - OPUS4-30103 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachsmuth, Janne A1 - Bohse, Jürgen T1 - Schallemissionsanalyse von Schadensmechanismen an Feinkornstahl T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-30106 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gumenyuk, Andrey A1 - Petrovskiy, V.N. A1 - Rethmeier, Michael A1 - Shcheglov, Pavel A1 - Uspenskiy, S.A. T1 - Condensed metal particles influence during the high power fiber laser welding N2 - Different types of lasers are used nowadays for a number of technological Solutions, Modem high power solid-state lasers with high brightness of Radiation like Fiber or disc lasers find ever more applications in welding technology. Apart from the replacement of the CC>2-iasers traditionaHy used fcr these purposes, they provide new technological possibilities of metal treatment, such as using industrial robots and remote welding with high power laser radiation. The possibility of flexible optical fiber delivery of the radiation to any point gives a great technological advantage and permits welding processes to be realized with complicated weld seam geomelries and different positions using a minimum of additional fixtures. The short wavelength of the high power solid state lasers (1.07 ’m) causes another advantage. The coefflcient of inverse 170 Bremsstrahlung absorption from free electrons in plasma for such radiation is about 100 times lower than for the COi-iaser radiation. Owing to this fact, using the solid state lasers allows it to avoid a negative influence of the welding plume. However, a short wavelength can lead to another kind of laser Radiation attenuation, which is connected with the formation of a cloud consisting of small metal particles that absorb and scatter laser radiation. This cloud arises due to the condensation of hot metal vapor by flying out from the deep Penetration channel and broadening in relatively cold atmosphere over the metal Surface. Some theoretical and experimental approaches were made in advance in Order to estimate the influence of the Condensed particles on laser radiation and welding quality. In this paper a systematic study including the determination of the Cloud size and its dynamical characteristics is presented. The results were obtained within the scope of the first stage of the metal vapor condensation process Investigation during welding with high power fiber lasers. T2 - International Conference 'Lasers in Science, Technology, Medicine' CY - Moscow, Russia DA - 19.09.2011 PY - 2011 VL - 22 SP - 170 EP - 177 AN - OPUS4-29166 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Auersch, Lutz T1 - Mitigation measures for ballasted tracks - sleepers, sleeper pads and substructure - Results from the finite element boundary element method N2 - The ground vibrations, which are generated by trains on different tracks, have been calculated by finite-element boundary-element models. The ballasted track is modelled in detail by the finite element method. The infinite soil is modelled by the boundary element method as a homogeneous or layered half-space. The track-soil system is coupled with a simple rigid mass model of the vehicle so that the vehicle-track interaction is completely included. Transfer functions are calculated in frequency domain without and with vehicle-track interaction, the compliance of the track and the mobilities of the soil at different distances from the track. Finally, the ratios between the ground vibration amplitudes with and without mitigation measure are calculated to quantify the effectiveness of the mitigation measure. Tracks with under sleeper pads have been investigated in a wide parameter study. The main parameters that influence the reduction of ground vibration are the stiffness of the under sleeper pad, the mass and the width of the sleeper. The softest sleeper pad yields the best reduction of the ground vibration. The influence of the sleeper mass is not as strong as the characteristic frequency is ruled by the mass of the sleeper and the mass of the wheelset as well. The influence of other parameters has been examined. The stiffness of the rail pads, the bending stiffness of the track, the stiffness of the ballast, the sub-soil, and the soil, and the layering of the soil. All these parameters show no or only a minor influence on the mitigation effect. As the standard isolated track, a track with an under sleeper pad of a stiffness of kS = 5 107 N/m has been chosen, which can also be expressed as a stiffness per area of kS ’’ = 7.4 107 N/m3 = 0.074 N/mm3. The resonance frequency for this pad stiffness is observed between 32 and 40 Hz. The reduction of the ground vibration is about vi,I /vi,U = 0.2 and 0.1 at 100 Hz. The reduction can be improved by softer sleeper pads. But the compliance of the track gets higher than tolerable. A possibility to use softer sleeper pads without increasing the static compliance of the track is their combination with wide sleepers. The softer sleeper pads under wider sleepers yield the same compliance of the track and a better reduction of the ground vibration. KW - Heavy sleeper KW - Under sleeper pad KW - Finite-element boundary-element method KW - Mitigation KW - Ground vibration KW - Ballasted track PY - 2011 SP - 1 EP - 81 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-56607 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kluge, Martin A1 - Ferrero, Fabio A1 - Zeps, Robert T1 - Simulation and experimental determination of the self ignition of tetrafluoroethylene in a 100-dm³-autoclave N2 - The gaseous TFE is a monomer which is used to form PTFE, also known as Teflon®, by a polymerisation process at elevated conditions of temperature and pressure. TFE belongs to the group of chemically instable gases which are able to decompose under specific conditions releasing a huge amount of heat comparable to a gas explosion of flammable gases. Due to several incidents in PTFE – production plants the investigation of the safety related properties of TFE at elevated condition was necessary and resulted in a research project at BAM which is subsidized by the PlasticsEurope association. In a first stage the pressure dependence of the Minimum Ignition Temperature for Decomposition (MITD) was determined in the range of 0.5 MPa - 3 MPa in small autoclaves with volumes of 0.2 dm³ and 3 dm³. These results were used to validate the numerical model and were found to correlate quite well with the simulated values. Nevertheless the applicability had to be confirmed for larger volumes as well. Therefore a heat able 100-dm³-autoclave was constructed and build to determine the MITD in the range of 0.5 MPa to 1.1 MPa. T2 - 8th European Congress of Chemical Engineering CY - Berlin, Germany DA - 25.09.2011 KW - Ignition temperature KW - Self decomposition KW - MITD KW - TFE KW - Tetrafluoroehtylene PY - 2011 N1 - Das Poster hat den Adolf-Martens-Preis im Bereich "Safety Engineering" erhalten. - The poster was awarded the Adolf Martens Prize in the section "Safety Engineering". N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. AN - OPUS4-55754 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Cruzado, A. A1 - Hartelt, Manfred A1 - Wäsche, Rolf A1 - Urchegui, M.A. A1 - Gómez, X. T1 - Fretting wear of thin steel wires. Part 2: Influence of crossing angle N2 - The wear behaviour of thin steel wires has been analyzed under oscillating sliding conditions in crossed cylinders contact geometry. The focus of this analysis was the influence of the crossing angle between the wires on the wear. The wires used had 0.45 mm in diameter and the material was cold-drawn eutectoid carbon steel (0.8% C) with a tensile strength higher than 2800 MPa. Two different types of tests were carried out, the first one representing the influence of the crossing angle for a constant load and the second one representing the influence of the crossing angle with constant contact pressure. In the first type of tests it was seen that as the contact angle decreases the contact pressure decreases too and hence less energy specific wear resistance is observed. As a consequence less wear is produced, thus increasing the life of the wires. In the second type of tests it was seen that with constant contact pressure but different crossing angles, nearly the same energy specific wear resistance was observed. This points at an identical wear behaviour in both type of tests but with a running-in and a steady state period as two different wear periods. The tests showed that the running in period may play an important role in the overall wear particle generation and hence the wear occurring in the steady state period is rather mild. KW - Fretting KW - Wires KW - Contact pressure KW - Crossing angle PY - 2011 DO - https://doi.org/10.1016/j.wear.2011.04.012 SN - 0043-1648 VL - 273 IS - 1 SP - 60 EP - 69 PB - Elsevier CY - Amsterdam AN - OPUS4-31762 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klieboldt, Ulrich T1 - UN 6(d) Test Results T2 - 11th International Conference of Chief Inspectors of Explosives CY - Salt Lake City, UT, USA DA - 2011-05-02 PY - 2011 AN - OPUS4-30997 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klieboldt, Ulrich T1 - Exclusion from Class 1 T2 - 11th International Conference of Chief Inspectors of Explosives CY - Salt Lake City, UT, USA DA - 2011-05-02 PY - 2011 AN - OPUS4-30998 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine A1 - Gradt, Thomas A1 - Österle, Werner A1 - Brückner, A. A1 - Weihnacht, V. T1 - Friction and endurance of MoS/2/ta-C coatings produced by laser arc deposition T2 - European Symposium on Friction, Wear and Wear Protection CY - Karlsruhe, Germany DA - 2011-11-26 PY - 2011 AN - OPUS4-30881 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Woydt, Mathias A1 - Kelling, Norbert T1 - Stribeck-type curves of alternative engine oils - Part I: Gray cast iron liners N2 - Wear tests are often used in engine development in order to characterize the functional profile of surfaces interacting with lubricants. This paper proposes a new test procedure to determine Stribeck-type curves for the tribosystem piston ring/cylinder liner involving test pieces prepared from engine components. The Variation of the friction coefficient with sliding speed depends on the structure and Constitution of the base oil, the viscosity index, the surface topography of the liner and ring, and the friction modifiers used. Novel organic friction modifiers of low molecular mass not only reduce the friction coefficients under mixed / boundary lubrication, but also in the fluid film regime. In addition, the influence of surface roughness on the wettability of surfaces can be significant for both static and dynamic wetting. For this reason, the interaction of the lubricant with the surfaces was also investigated to enable a correlation between the surface properties of the liquid and solid phases and the tribological behavior. T2 - 52. Tribologie-Fachtagung - Reibung, Schmierung und Verschleiß - Forschung und praktische Anwendungen CY - Göttingen, Deutschland DA - 26.09.2011 PY - 2011 SN - 978-3-00-035439-7 VL - Part I SP - 32/1 EP - 32/12 AN - OPUS4-31752 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Woydt, Mathias T1 - Oil free machinery and ZERO WEAR - Dream or reality? N2 - Original equipment manufacturers (OEMs) and end-users perceive 'Zero Wear' differently. The 'Zero Wear' approach will be put into a general relation for different applications and illuminated by individual paths, either based on monolithic materials, thin film coatings or alternative base oils, featuring triboactive materials and lubricious oxides for tribological engine components and dry running foil bearings or specific DLC, ta-C and novel Zirconium-based thin film coatings for concentrated contacts above FZG 14 and alternative engine oils (NoSAP & bio-no-tox). The associated tribometric test equipments for these examples will also be detailed. KW - Zero wear KW - SRV KW - Triboactive coatings KW - (Ti,Mo)(C,N) KW - Tin-2Cr2O2n-1 KW - Magnéli KW - DLC KW - Zr(C,N), KW - ta-C KW - Polyglycol PY - 2011 DO - https://doi.org/10.2474/trol.6.101 SN - 1881-2198 VL - 6 IS - 1 SP - 101 EP - 112 CY - Tokyo, Japan AN - OPUS4-31746 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Martínez-Mánez, Ramon A1 - Sancenón, F. A1 - Hecht, Mandy A1 - Biyikal, Mustafa A1 - Rurack, Knut T1 - Nanoscopic optical sensors based on functional supramolecular hybrid materials N2 - This review highlights how the combination of supramolecular principles and nanoscopic solid structures enables the design of new hybrid sensing ensembles with improved sensitivity and/or selectivity and for the targeting of analytes for which selectivity is hard to achieve by conventional methods. Such ideas are bridging the gap between molecules, materials sciences and nanotechnology. Relevant examples will be detailed, taking into account functional aspects such as (1) enhanced coordination of functionalized solids, (2) enhanced signalling through preorganization, (3) signalling by assembly–disassembly of nanoscopic objects, (4) biomimetic probes utilizing discrimination by polarity and size and (5) distinct switching and gating protocols. These strategies are opening new prospects for sensor research and signalling paradigms at the frontier between nanotechnology, smart materials and supramolecular chemistry. KW - Supramolecular chemistry KW - Optical probes KW - Nanotechnology KW - Hybrid organic-inorganic materials PY - 2011 DO - https://doi.org/10.1007/s00216-010-4198-2 SN - 1618-2642 SN - 1618-2650 VL - 399 IS - 1 SP - 55 EP - 74 PB - Springer CY - Berlin AN - OPUS4-22908 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Naghib Zadeh, Hamid A1 - Glitzky, Carsten A1 - Österle, Werner A1 - Rabe, Torsten T1 - Low temperature sintering of barium titanate based ceramics with high dielectric constant for LTCC applications N2 - The sintering temperature of BaTiO3 powder was reduced to 900 °C due to the ZnO-B2O3-Li2O-Nb2O5-Co2O3 addition. Excellent densification was achieved after sintering at 900 °C for 2 h. The low sintering temperature of newly developed capacitor materials allows a co-firing with pure silver electrodes. The dielectric constant and the temperature stability of the dielectric constant are strongly correlated with the composition of the ZnO-B2O3-Li2O additives. A high dielectric constant up to 3000 and a dielectric loss less than 0.024 were measured on multilayer capacitors sintered at 900 °C with silver inner electrodes. KW - BaTiO3 and titanates KW - Capacitors KW - Dielectric properties KW - LTCC PY - 2011 DO - https://doi.org/10.1016/j.jeurceramsoc.2010.10.003 SN - 0955-2219 SN - 1873-619X VL - 31 IS - 4 SP - 589 EP - 596 PB - Elsevier Ltd. CY - Oxford AN - OPUS4-22886 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Petzet, S. A1 - Peplinski, Burkhard A1 - Bodkhe, S.Y. A1 - Connel, P. T1 - Phosphorus and Aluminium Recovery from Sewage Sludge Ash by a novel two Step wet chemical Elution Process (SESAL-Phos - Recovery Process) T2 - Nutrient Recovery and Management Conference (International Water Association) CY - Miami, FL, USA DA - 2011-01-09 PY - 2011 AN - OPUS4-22902 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Merkel, Stefan A1 - Köppen, Robert A1 - Koch, Matthias A1 - Nehls, Irene T1 - Ergotalkaloide - Epimerisierungsfreie Analytik als Lösung eines alten Problems T2 - 21. Doktorandenseminar des AK "Separation Science" CY - Hohenroda, Germany DA - 2011-01-09 PY - 2011 AN - OPUS4-22903 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Beke, S. A1 - Kobayashi, T. A1 - Sugioka, K. A1 - Midorikawa, K. A1 - Bonse, Jörn T1 - Time-of-flight mass spectroscopy of femtosecond and nanosecond laser ablated TeO2 crystals N2 - Single-pulse femtosecond (fs) (pulse duration ~200 fs, wavelength 398 nm) and nanosecond (ns) (pulse duration 4 ns, wavelength 355 nm) laser ablation have been applied in combination with time-of-flight mass spectrometer (TOFMS) to analyze the elemental composition of the plasma plume of single-crystalline telluria (c-TeO2, grown by the balance controlled Czochralski growth method). Due to the three-order difference of the peak intensities of the ns and fs-laser pulses, significant differences were observed regarding the laser-induced species in the plasma plume. Positive singly, doubly and triply charged Te ions (Te+, Te2+, Te3+) in the form of their isotopes were observed in case of both irradiations. In case of the ns-laser ablation the TeO+ formation was negligible compared to the fs case and there was no Te trimer (Te3+) formation observed. It was found that the amplitude of Te ion signals strongly depended on the applied laser pulse energy. Singly charged oxygen ions (O+) are always present as a byproduct in both kinds of laser ablation. KW - Time-of-flight mass spectroscopy KW - Tellurium dioxide crystals KW - second laser KW - Nanosecond laser KW - Ablation PY - 2011 DO - https://doi.org/10.1016/j.ijms.2010.08.022 SN - 0168-1176 SN - 0020-7381 SN - 1387-3806 SN - 1873-2798 VL - 299 IS - 1 SP - 5 EP - 8 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-22490 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zerbst, Uwe A1 - Schödel, M. A1 - Beier, H.T. T1 - Parameters affecting the damage tolerance behaviour of railway axles N2 - The paper provides a discussion on damage tolerance options applied to railway axles and factors influencing the residual lifetime as well as the required inspection interval. These comprise material properties such as the scatter of the da/dN–ΔK curve, the fatigue crack propagation threshold ΔKth and the toughness of the material. Parameters affecting axle loading such as the press fit, rotating bending, load history and mixed crack opening modes are discussed. Finally the influence of the initial crack geometry on residual lifetime is simulated. KW - Railway axles KW - Damage tolerance KW - Fatigue crack propagation PY - 2011 DO - https://doi.org/10.1016/j.engfracmech.2010.03.013 SN - 0013-7944 SN - 1873-7315 VL - 78 IS - 5 SP - 793 EP - 809 PB - Elsevier Science CY - Kidlington AN - OPUS4-22491 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Madia, Mauro A1 - Beretta, S. A1 - Schödel, M. A1 - Zerbst, Uwe A1 - Luke, M. A1 - Varfolomeyev, I. T1 - Stress intensity factor solutions for cracks in railway axles N2 - The aim of this paper is a collection of stress intensity factor solutions for cracks in railway axle geometries which the authors of the present special issue developed and/or used for damage tolerance analyses. These solutions comprise closed form analytical as well as tabled geometry functions and they refer to solid as well as hollow axles and various crack sites such as the T- and V-notch and the axle body. KW - Railway axles KW - Stress intensity factor PY - 2011 DO - https://doi.org/10.1016/j.engfracmech.2010.03.019 SN - 0013-7944 SN - 1873-7315 VL - 78 IS - 5 SP - 764 EP - 792 PB - Elsevier Science CY - Kidlington AN - OPUS4-22495 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beck, Uwe A1 - Hertwig, Andreas A1 - Stephanowitz, Ralph A1 - Weise, Matthias A1 - Hönig, D. A1 - Schneider, S. A1 - Domnick, R. A1 - Belzner, M. T1 - Verification and Authentication of Surface- and Layer-embedded information for Anti-counterfeiting Applications by Imaging Ellipsometry T2 - 6th Workshop Ellipsometry CY - Berlin, Germany DA - 2011-02-21 PY - 2011 AN - OPUS4-22434 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bremser, Wolfram A1 - Lücke, F.-K. A1 - Urmetzer, C. A1 - Fuchs, E. A1 - Leist, U. T1 - An approach to integrated data assessment in a proficiency test on the enumeration of Escherichia coli KW - Bias KW - Data assessment KW - Escherichia coli KW - Precision KW - Proficiency testing KW - Statistics PY - 2011 DO - https://doi.org/10.1111/j.1365-2672.2010.04866.x SN - 1364-5072 VL - 110 IS - 1 SP - 128 EP - 138 PB - Wiley-Blackwell CY - Malden, Mass., USA AN - OPUS4-22649 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dörfel, Ilona A1 - Rooch, Heidemarie A1 - Österle, Werner A1 - Kranzmann, Axel T1 - Vanadium and chromium containing precipitates in heat resistant steel T92 T2 - "Current Developments in TEM" (JEOL user meeting) CY - Freiberg, Germany DA - 10.03.2011 PY - 2011 AN - OPUS4-22678 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zerbst, Uwe A1 - Beretta, S. T1 - Failure and damage tolerance aspects of railway components N2 - Railway structures such as rails and axles are safety relevant components since any failure includes the risk of catastrophic derailment. This paper gives a brief overview on the most important potential failure scenarios driven by fatigue crack initiation and propagation and discusses the effects of important influencing factors such as vehicle weight and speed, track quality and environmental conditions. The present paper summarizes earlier work of the authors in this field. KW - Railway rails KW - Railway axles KW - Fatigue crack propagation KW - Damage tolerance KW - Fracture mechanics PY - 2011 DO - https://doi.org/10.1016/j.engfailanal.2010.06.001 SN - 1350-6307 SN - 1873-1961 VL - 18 IS - 2 SP - 534 EP - 542 PB - Elsevier Science Publ. CY - Oxford AN - OPUS4-22639 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gorbushina, Anna A1 - Kempe, A. A1 - Rodenacker, K. A1 - Jütting, U. A1 - Altermann, W. A1 - Stark, R.W. A1 - Heckl, W.M. A1 - Krumbein, W.E. T1 - Quantitative 3-dimensional image analysis of mineral surface modifications - chemical, mechanical and biological N2 - Three principally different mechanisms contribute to the wear-down process of mineral aggregates in sedimentary environments: (1) mechanical abrasion by forces of wind and water and by floating or saltating neighbouring grains, (2) chemical attack and dissolution by fluids, and (3) physical bioerosion and chemical biocorrosion. It is however, difficult to attribute the specific surface changes to specific environments and processes. Quartz sand grains from subaerial and subaquatic environments were analysed by atomic force microscopy (AFM) for traces of natural and experimental aeolian, aquatic and biological wear-down processes. Quantitative topographical parameters of surface alterations were extracted from topography data by non-linear methods derived from digital image analysis. These parameters were examined by multivariate statistic, yielding three well-distinguishable groups. Morphological surface alterations dominated by subaerial, subaquatic and by biological impact could be differentiated. The method may also be used for the detection of aeolian, subaquatic, and biological modification of sedimentary grains and rock surfaces in extraterrestrial environments, and for assessment of environmental damage on monuments and buildings. KW - Sediment grain corrosion KW - Chemical grain pitting KW - Biological grain pitting KW - Aquatic grain corrosion KW - Biopitting KW - Weathering KW - Surface analysis KW - Nano-structure of grain and mineral surfaces PY - 2011 DO - https://doi.org/10.1080/01490451.2010.490077 SN - 0149-0451 VL - 28 SP - 1 EP - 13 PB - Crane, Russak & Co. CY - New York, NY, USA AN - OPUS4-23058 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Khoun, L. A1 - de Oliveira, Rui A1 - Michaud, V. A1 - Hubert, P. T1 - Investigation of process-induced strains development by fibre Bragg grating sensors in resin transfer moulded composites N2 - A comprehensive understanding of the development of residual strains in composite processing is essential to manufacture high quality composite parts. In this paper, the use of fibre Bragg grating (FBG) optical sensors was investigated to measure in situ the build-up of the process-induced strains in composite panels manufactured by resin transfer moulding. The FBG sensors, embedded in the composite laminate, successfully measured the evolution of the composite in-plane strains due to the temperature history. The sensors also captured a strain discontinuity during the cool-down related to the debonding of the composite from the mould. Finite element models were then proposed to simulate the strain development measured by the FBG sensors. Three different contact interactions between the tool and the laminate were investigated: no bonding, perfect bonding and frictional contact. The model using the frictional contact interaction described well the evolution of the measured strains. KW - A. Polymer-matrix composites KW - B. Residual/internal stress KW - D. Process monitoring PY - 2011 DO - https://doi.org/10.1016/j.compositesa.2010.11.013 SN - 1359-835X VL - 42 IS - 3 SP - 274 EP - 282 PB - Elsevier Ltd. CY - Oxford AN - OPUS4-23059 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Illerhaus, Bernhard A1 - Arnold, S. T1 - Scattered Radiation Grids used for Micro Computed Tomography T2 - DIR2011, 20.-22.Juni, Veranstaltung DGZfP-BAM CY - Berlin, Germany DA - 2011-06-20 PY - 2011 AN - OPUS4-23061 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hertwig, Andreas A1 - Beck, Uwe A1 - Männ, Marion A1 - Weise, Matthias T1 - Reference coatings for thin film technology - beyond the state of the art T2 - 6th Workshop Ellipsometry CY - Berlin, Germany DA - 2011-02-02 PY - 2011 AN - OPUS4-23064 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Girard-Lauriault, Pierre-Luc A1 - Dietrich, Paul A1 - Gross, Thomas A1 - Unger, Wolfgang T1 - Quantitative Chemical Determination of Organic Layers using CDXPS: A Standard Experimental Procedure? T2 - Seminar für Oberflächentechnik - Wintersemester 2010/2011 Gemeinsame Veranstaltung des Instituts für Oberflächentechnik der TU Braunschweig (IOT) mit dem Fraunhofer-Institut für Schicht- und Oberflächentechnik (IST) Braunschweig CY - Braunschweig, Germany DA - 2011-02-01 PY - 2011 AN - OPUS4-23067 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griepentrog, Michael T1 - Möglichkeiten und Grenzen der Bestimmung mechanischer Eigenschaften von Kombinationsschichten T2 - Berliner Fachseminar: Kombinationsschichten - Informationen über Anforderungen und Leistungsfähigkeit (DGO - BAM) CY - Berlin, Germany DA - 2011-01-27 PY - 2011 AN - OPUS4-23071 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian T1 - Adhäsion zwischen Faser und Matrix - Schlüssel zu leistungsfähigen Verbundwerkstoffen T2 - DVS - 50 Jahre Kleb-, Gießharz und Laminiertechnik, BAM CY - Berlin, Germany DA - 2011-01-21 PY - 2011 AN - OPUS4-23073 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heyn, Andreas T1 - Möglichkeiten elektrochemischer Zustandsbewertung von Korrosionsschutzsystemen T2 - Sitzung des Arbeitsausschusses "Elektrochemische Prozesse", ProcessNet Thema "Korrosion und Galvanotechnik" CY - Frankfurt am Main, Germany DA - 2011-01-24 PY - 2011 AN - OPUS4-23074 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Burkert, Andreas A1 - Sarmiento Klapper, Helmuth T1 - Elektrochemische Untersuchungen zur korrosionssicheren Werkstoffauswahl bei geothermischen Anlagen T2 - Sitzung des ProzessNet-Arbeitsausschusses "Elektrochemische Prozesse" CY - Frankfurt am Main, Germany DA - 2011-01-19 PY - 2011 AN - OPUS4-23075 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bidarra, A. A1 - Buzanich, Günter A1 - Coroado, J. A1 - Rocha, F. T1 - A multianalytical approach to the study of gold leaf from a baroque altarpiece T2 - Technart 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-23080 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Christian A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Buzanich, Günter A1 - Riesemeier, Heinrich T1 - SRXRF-measurements at non planar objects: Automatic determination of the angle of incidence of the exciting X-ray T2 - Technart 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-23081 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Radtke, Martin A1 - Scharf, O. A1 - Reinholz, Uwe A1 - Bjeoumikova, S. A1 - Wedell, R. A1 - Soltau, H. A1 - Gubzhokov, Renat A1 - Riesemeier, Heinrich A1 - Langhoff, N. A1 - Ihle, S. T1 - First images of a colour X-ray camera, a detector with high resolution in energy and space T2 - Technart 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-23082 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schoknecht, Ute T1 - Leachingtests für Beschichtungen - Möglichkeiten und Grenzen T2 - Seminar der Technischen Akademie Esslingen "Auswaschung aus beregneten Fassaden" CY - Ostfildern, Germany DA - 2011-02-21 PY - 2011 AN - OPUS4-23084 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naumann, Annette A1 - Heine, G. A1 - Rauber, R. T1 - Wurzelidentifizierung in einem Mischbestand: Fallstudie Erbse-Hafer T2 - Carl-Sprengel-Kolloquium, Department für Nutzpflanzenwissenschaften, Universität Göttingen CY - Göttingen, Germany DA - 2011-02-09 PY - 2011 AN - OPUS4-23085 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meyer-Plath, Asmus A1 - Oleszak, Franz A1 - Maneck, Heinz-Eberhard A1 - Mach, Reinhard T1 - Highly effective purification of carbon nanotubes by plasma-thermal annealing T2 - Inno. CNT Jahrestagung CY - Ettlingen, Germany DA - 2011-01-25 PY - 2011 AN - OPUS4-23093 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Huber, Alexandra A1 - Illgen, René A1 - Hanelt, Sven A1 - Jäger, Christian A1 - Unger, Wolfgang A1 - Meyer-Plath, Asmus T1 - Physico-chemical characterization of CNT by XPS and NMR T2 - Inno. CNT Jahrestagung CY - Ettlingen, Germany DA - 2011-01-25 PY - 2011 AN - OPUS4-23094 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kuhlbusch, T. A1 - Meyer-Plath, Asmus A1 - Plitzko, S. A1 - Ragot, J. A1 - Schäffer, A. A1 - Voetz, M. T1 - Carbo-Safe - Sicherheit, Gesundheit und Qualität im Umgang mit CNT T2 - Inno. CNT Jahrestagung CY - Ettlingen, Germany DA - 2011-01-25 PY - 2011 AN - OPUS4-23108 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zenkel, C. A1 - Albuerne, J. A1 - Meyer-Plath, Asmus A1 - Dresel, A. A1 - Brinks, M. A1 - Helbig, J. A1 - Abetz, V. A1 - Boschetti, A. T1 - Charakterisierung von Seitenwandfunktionalisierten Kohlenstoffnanoröhren T2 - Inno. CNT Jahrestagung CY - Ettlingen, Germany DA - 2011-01-25 PY - 2011 AN - OPUS4-23113 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wloka, Monika T1 - Einführung in Zielsetzung, Ablauf des Verfahrens der Novellierung und Überblick über die Änderungen der DIN EN ISO 19011:2002 T2 - Kooperationsveranstaltung DIN/DGQ: Revision DIN EN ISO 19011 CY - Berlin, Germany DA - 2011-01-27 PY - 2011 AN - OPUS4-23248 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Piechotta, Christian A1 - Cossmer, Antje A1 - Klyk-Seitz, Urszula-Anna A1 - Nehls, Irene T1 - Quantification of Tributyltin (TBT) at Sub-ppt Level in Whole Water Samples T2 - Canas 2011 CY - Leipzig, Germany DA - 2011-03-13 PY - 2011 AN - OPUS4-23249 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fettig, Ina A1 - Piechotta, Christian A1 - Krüger, Simone A1 - Deubel, Jan A1 - Riexinger, D. A1 - Raspe, Tina A1 - Nehls, Irene T1 - Chemische Brandspurenanalytik - Nachweis von Benzin in Brandrückständen T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23250 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Piechotta, Christian A1 - Krüger, Simone A1 - Fettig, Ina A1 - Deubel, Jan A1 - Riexinger, D. A1 - Raspe, Tina A1 - Nehls, Irene T1 - Chemische Brandspurenanalytik - Methoden zum Nachweis von Brandbeschleunigern in Brandrückständen T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23251 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gradt, Thomas A1 - Theiler, Geraldine T1 - Tribological behaviour of solid lubricants in hydrogen environment N2 - For further development of hydrogen technology, it is necessary to have a sufficient number of materials for safe and reliable operation available. Frictional contacts exposed to hydrogen, are critical because of vanishing protective oxide layers in the presence of a chemical reducing environment. Furthermore, liquid lubricants are often not applicable, because of purity requirements, or very low temperatures in the case of liquid hydrogen. Thus, for numerous tribosystems in hydrogen technology, solid lubrication is the only possible method for reducing friction and wear. Therefore, investigations on the tribological behaviour of friction reducing materials, such as PTFE, graphite, DLC and MoS2, in inert and hydrogen environment were carried out. The results show that solid lubricants, applied as coatings or as components in polymer composites, are able to reduce friction and wear in gaseous as well as in liquid hydrogen. However, some materials are very sensitive to the environmental medium. KW - Hydrogen environment KW - Low temperatures KW - Solid lubricants KW - Coatings KW - Polymer composites PY - 2011 DO - https://doi.org/10.247/trol.6.117 SN - 1881-2198 VL - 6 IS - 2 SP - 117 EP - 122 CY - Tokyo, Japan AN - OPUS4-23252 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hoffmann, Katrin A1 - Dietzel, B. A1 - Schulz, B. A1 - Reck, Günter A1 - Hoffmann, Angelika A1 - Orgzall, I. A1 - Resch-Genger, Ute A1 - Emmerling, Franziska T1 - Combined structural and fluorescence studies of methyl-substituted 2,5-diphenyl-1,3,4-oxadiazoles - relation between electronic properties and packing motifs N2 - Prerequisite for the rational design of functional organic materials with tailor-made electronic properties is the knowledge of the structure–property relationship for the specific class of molecules under consideration. This encouraged us to systematically study the influence of the molecular structure and substitution pattern of aromatically substituted 1,3,4-oxadiazoles on the electronic properties and packing motifs of these molecules and on the interplay of these factors. For this purpose, seven diphenyl-oxadiazoles equipped with methyl substituents in the ortho- and meta-position(s) were synthesized and characterized. Absorption and fluorescence spectra in solution served here as tools to monitor substitution-induced changes in the electronic properties of the individual molecules whereas X-ray and optical measurements in the solid state provided information on the interplay of electronic and packing effects. In solution, the spectral position of the absorption maximum, the size of Stokes shift, and the fluorescence quantum yield are considerably affected by ortho-substitution in three or four ortho-positions. This results in blue shifted absorption bands, increased Stokes shifts, and reduced fluorescence quantum yields whereas the spectral position and vibrational structure of the emission bands remain more or less unaffected. In the crystalline state, however, the spectral position and shape of the emission bands display a strong dependence on the molecular structure and/or packing motifs that seem to control the amount of dye–dye-interactions. These observations reveal the limited value of commonly reported absorption and fluorescence measurements in solution for a straightforward comparison of spectroscopic results with single X-ray crystallography. This underlines the importance of solid state spectroscopic studies for a better understanding of the interplay of electronic effects and molecular order. KW - Diphenyl-oxadiazoles KW - X-ray structure KW - Packing motif KW - Optical properties KW - Fluorescence quantum yield PY - 2011 DO - https://doi.org/10.1016/j.molstruc.2010.11.071 SN - 0022-2860 SN - 1872-8014 SN - 0377-046X VL - 988 IS - 1-3 SP - 35 EP - 46 PB - Elsevier CY - Amsterdam AN - OPUS4-23253 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Herbst, Tristan A1 - Rübner, Katrin A1 - Meng, Birgit ED - Teipel, U. ED - Schmidt, R. T1 - Ganzheitliche Eignungsbewertung potenzieller Recyclingbereiche für Mauerwerksbruch N2 - Unsere Industriegesellschaft ist auf den ständigen Abbau und Verbrauch von Rohstoffen und Energie angewiesen. Der Bausektor zählt dabei zu den größten Verursachern von Stoffströmen in Deutschland. Zum einen ist das Bauen mit einem hohen Bedarf an materiellen und energetischen Ressourcen sowie finanziellen Aufwendungen verbunden. Zum anderen sind nahezu 50 % des deutschen Abfallaufkommens dem Bausektor zuzurechnen, Die Beschränktheit natürlicher Ressourcen, die zunehmenden negativen Umweltauswirkungen sowie die Verteuerung und Verknappung von Deponieraum führten in den letzten Jahren zu einem Umdenken in der Bau- und Abfallwirtschaft hin zu einer Kreislaufwirtschaft. Im Sinne einer nachhaltigen Kreislaufwirtschaft sind die im Bausektor anfallenden Restmassen zukünftig möglichst einem Recycling zuzuführen. Bei der Wahl der geeigneten Recyclingoption spielen technische, ökologische und ökonomische Fragestellungen eine Rolle. Für den Bereich Mauerwerksrecycling existiert bisher keine umfassende Methodik zur ganzheitlichen Eignungsbewertung (Technik, Ökologie, Ökonomie) mit einem vertretbaren Arbeitsaufwand. Grundlegende strukturierte und strukturierende Informationen für das Recycling von Mauerwerksbruch fehlen bislang. Aus diesem Grunde wird derzeit mit dem Ziel eines möglichst hochwertigen Mauerwerksrecyclings eine umfassende und praxisorientierte Methodik entwickelt. Diese Methodik soll eine ganzheitliche Eignungsbewertung unterschiedlicher potenzieller Recyclingbereiche für Mauerwerksbruch ermöglichen. Im vorliegenden Beitrag werden erste Ansätze dieser Bewertungsmethode vorgestellt. T2 - 2. Symposium "Rohstoffeffizienz und Rohstoffinnovationen" CY - Nürnberg, Germany DA - 10.02.2011 PY - 2011 SN - 978-3-8396-0222-5 VL - 2 SP - 153 EP - 165 PB - Fraunhofer Verlag AN - OPUS4-23255 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Reinecke, E.-A. A1 - Hübert, Thomas A1 - Tkatschenko, I. A1 - Kessler, A. A1 - Kuznetsov, M. A1 - Wilkins, M. A1 - Hedley, D. A1 - Azkarate, I. A1 - Proust, C. A1 - Acosta-Iborra, B. A1 - Gavrikov, B. A1 - De Bruijn, P.C.J. A1 - Marangon, A. A1 - Teodorczyk, A. A1 - Grafwallner, A. T1 - Integration of experimental facilities: a joint effort for establishing a common knowledge base in experimental work on hydrogen safety N2 - In the area of hydrogen safety, research facilities are essential for the experimental investigation of relevant phenomena, for testing devices and safety concepts, as well as for the generation of validation data for the various numerical codes and models. Within the framework of the European HySafe Network of Excellence (NoE), the 'Integration of Experimental Facilities (IEF)' activity has provided basic support for joint experimental work. Even beyond the funding period of the HySafe NoE in the 6th Framework Program, IEF represents a long-lasting effort for the sustainable integration of experimental research capacities and expertise of the partners from different research fields. In order to achieve a high standard in the quality of experimental data provided by the partners, emphasis was put on the know-how transfer between the partners. On the one hand, documentation on the experimental capacities was prepared and analyzed. On the other hand, a wiki-based communication platform was established, supported by biannual workshops covering topics ranging from measurement technologies to safety issues. Based on the partners' contributions, a working document was created on best practice including the joint experimental knowledge of all partners with regard to experimental set-ups and instrumentation. The paper gives an overview of the IEF partners and the network activities over the last five years. KW - Hydrogen safety KW - Experiments PY - 2011 DO - https://doi.org/10.1016/j.ijhydene.2010.04.162 SN - 0360-3199 VL - 36 IS - 3 SP - 2700 EP - 2710 PB - Elsevier CY - Oxford AN - OPUS4-23257 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mermillod-Blondin, A. A1 - Mauclair, C. A1 - Bonse, Jörn A1 - Stoian, R. A1 - Audouard, E. A1 - Rosenfeld, A. A1 - Hertel, I.V. T1 - Time-resolved imaging of laser-induced refractive index changes in transparent media N2 - We describe a method to visualize ultrafast laser-induced refractive index changes in transparent materials with a 310 fs impulse response and a submicrometer spatial resolution. The temporal profile of the laser excitation sequence can be arbitrarily set on the subpicosecond and picosecond time scales with a pulse shaping unit, allowing for complex laser excitation. Time-resolved phase contrast microscopy reveals the real part of the refractive index change and complementary time-resolved optical transmission microscopy measurements give access to the imaginary part of the refractive index in the irradiated region. A femtosecond laser source probes the complex refractive index changes from the excitation time up to 1 ns, and a frequency-doubled Nd:YAG laser emitting 1 ns duration pulses is employed for collecting data at longer time delays, when the evolution is slow. We demonstrate the performance of our setup by studying the energy relaxation in a fused silica sample after irradiation with a double pulse sequence. The excitation pulses are separated by 3 ps. Our results show two dimensional refractive index maps at different times from 200 fs to 100 µs after the laser excitation. On the subpicosecond time scale we have access to the spatial characteristics of the energy deposition into the sample. At longer times (800 ps), time-resolved phase contrast microscopy shows the appearance of a strong compression wave emitted from the excited region. On the microsecond time scale, we observe energy transfer outside the irradiated region. KW - High-speed optical techniques KW - Light transmission KW - Neodymium KW - Optical harmonic generation KW - Optical pulse shaping KW - Refractive index KW - Self-induced transparency KW - Silicon compounds KW - Solid lasers PY - 2011 UR - http://rsi.aip.org/resource/1/rsinak/v82/i3/p033703_s1 DO - https://doi.org/10.1063/1.3527937 SN - 0034-6748 SN - 1089-7623 VL - 82 IS - 3 SP - 033703-1 EP - 033703-8 PB - American Institute of Physics CY - Melville, NY AN - OPUS4-23308 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bonse, Jörn A1 - Rosenfeld, A. A1 - Krüger, Jörg T1 - Implications of transient changes of optical and surface properties of solids during femtosecond laser pulse irradiation to the formation of laser-induced periodic surface structures N2 - The formation of laser-induced periodic surface structures (LIPSS) upon irradiation of silicon wafer surfaces by linearly polarized Ti:sapphire femtosecond laser pulses (pulse duration 130 fs, central wavelength 800 nm) is studied experimentally and theoretically. In the experiments, so-called low-spatial frequency LIPSS (LSFL) were found with periods smaller than the laser wavelength and an orientation perpendicular to the polarization. The experimental results are analyzed by means of a new theoretical approach, which combines the widely accepted LIPSS theory of Sipe et al. with a Drude model, in order to account for transient (intra-pulse) changes of the optical properties of the irradiated materials. It is found that the LSFL formation is caused by the excitation of surface plasmon polaritons, SPPs, once the initially semiconducting material turns to a metallic state upon formation of a dense free-electron-plasma in the material and the subsequent interference between its electrical field with that of the incident laser beam resulting in a spatially modulated energy deposition at the surface. Moreover, the influence of the laser-excited carrier density and the role of the feedback upon the multi-pulse irradiation and its relation to the excitation of SPP in a grating-like surface structure is discussed. KW - Femtosecond laser ablation KW - Laser-induced periodic surface structures KW - (LIPSS) KW - Optical properties KW - Surface plasmon polaritons KW - Semiconductors KW - Silicon PY - 2011 DO - https://doi.org/10.1016/j.apsusc.2010.11.059 SN - 0169-4332 SN - 1873-5584 VL - 257 IS - 12 SP - 5420 EP - 5423 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-23309 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Symietz, Christian A1 - Lehmann, Erhard A1 - Gildenhaar, Renate A1 - Koter, Robert A1 - Berger, Georg A1 - Krüger, Jörg T1 - Fixation of bioactive calcium alkali phosphate on Ti6Al4V implant material with femtosecond laser pulses N2 - Bone implants made of metal, often titanium or the titanium alloy Ti6Al4V, need to be surface treated to become bioactive. This enables the formation of a firm and durable connection of the prosthesis with the living bone. We present a new method to uniformly cover Ti6Al4V with a thin layer of ceramics that imitates bone material. These calcium alkali phosphates, called GB14 and Ca10, are applied to the metal by dip coating of metal plates into an aqueous slurry containing the fine ceramic powder. The dried samples are illuminated with the 790 nm radiation of a pulsed femtosecond laser. If the laser fluence is set to a value just below the ablation threshold of the ceramic (ca. 0.4 J/cm²) the 30 fs laser pulses penetrate the partly transparent ceramic layer of 20–40 µm thickness. The remaining laser fluence at the ceramic–metal interface is still high enough to generate a thin metal melt layer leading to the ceramic fixation on the metal. The laser processing step is only possible because Ti6Al4V has a lower ablation threshold (between 0.1 and 0.15 J/cm²) than the ceramic material. After laser treatment in a fluence range between 0.1 and 0.4 J/cm², only the particles in contact with the metal withstand a post-laser treatment (ultrasonic cleaning). The non-irradiated rest of the layer is washed off. In this work, we present results of a successful ceramic fixation extending over larger areas. This is fundamental for future applications of arbitrarily shaped implants. KW - Bone implant KW - Bioceramic coating KW - Titanium KW - Calcium phosphate KW - Femtosecond laser PY - 2011 DO - https://doi.org/10.1016/j.apsusc.2010.10.046 SN - 0169-4332 SN - 1873-5584 VL - 257 IS - 12 SP - 5208 EP - 5212 PB - North-Holland CY - Amsterdam AN - OPUS4-23310 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wienecke, Bernd-Uwe T1 - Verpackungen (einschließlich Großpackmittel (IBC) und Großverpackungen) und Tanks (Stand 3/2011) T2 - Transport gefährlicher Stoffe - Seminar, Maikammer CY - Maikammer, Germany DA - 2011-03-02 PY - 2011 AN - OPUS4-23311 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gabitov, R.I. A1 - Schmitt, A.K. A1 - Rosner, Martin A1 - McKeegan, K.D. A1 - Gaetani, G.A. A1 - Cohen, A.L. A1 - Watson, E.B. A1 - Harrison, T.M. T1 - In situ delta7Li, Li/Ca, and Mg/Ca analyses of synthetic aragonites N2 - In situ secondary ion mass spectrometry (SIMS) analyses of δ7Li, Li/Ca, and Mg/Ca were performed on five synthetic aragonite samples precipitated from seawater at 25°C at different rates. The compositions of δ7Li in bulk aragonites and experimental fluids were measured by multicollector inductively coupled plasma–mass spectrometry (MC-ICP-MS). Both techniques yielded similar δ7Li in aragonite when SIMS analyses were corrected to calcium carbonate reference materials. Fractionation factors α7Li/6Li range from 0.9895 to 0.9923, which translates to a fractionation between aragonite and fluid from -10.5‰ to -7.7‰. The within-sample δ7Li range determined by SIMS is up to 27‰, exceeding the difference between bulk δ7Li analyses of different aragonite precipitates. Moreover, the centers of aragonite hemispherical bundles (spherulites) are enriched in Li/Ca and Mg/Ca relative to spherulite fibers by up to factors of 2 and 8, respectively. The Li/Ca and Mg/Ca ratios of spherulite fibers increase with aragonite precipitation rate. These results suggest that precipitation rate is a potentially important consideration when using Li isotopes and elemental ratios in natural carbonates as a proxy for seawater composition and temperature. KW - Lithium KW - Isotope KW - Aragonite KW - Rate KW - SIMS KW - Magnesium PY - 2011 DO - https://doi.org/10.1029/2010GC003322 SN - 1525-2027 VL - 12 IS - 3 (Technical Brief) SP - 1 EP - 16 CY - Washington, DC, USA AN - OPUS4-23312 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Proske, T. A1 - Kühne, Hans-Carsten T1 - Segregation of Coarse Aggregates in Self Compacting Concrete - Sedimentationsverhalten der groben Gesteinskörnung in Selbstverdichtendem Beton T2 - 20. Kolloquium und Workshop "Rheologische Messungen an Baustoffen" CY - Regensburg, Germany DA - 2011-03-01 PY - 2011 AN - OPUS4-23314 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Poli, Marco A1 - Grätz, Rainer A1 - Arndt, Detlef A1 - Scheider, Swen A1 - Schröder, Volkmar T1 - Explosionsdruckentlastungen unter dem Einfluss von Turbulenz T2 - ProcessNet Arbeitsausschuss "Sicherheitsgerechtes Auslegen von Chemieanlagen", Meyer Werft GmbH CY - Papenburg, Germany DA - 2011-03-02 PY - 2011 AN - OPUS4-23315 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tag, Mathias A1 - Bresch, Harald A1 - Seeger, Stefan A1 - Jann, Oliver A1 - Rotard, W. T1 - Study of aerosol cell exposure in an Air Liquid Interface T2 - Nanotechnology and Toxicology in Environment and Health CY - Leipzig, Germany DA - 2011-04-11 PY - 2011 N1 - Geburtsname von Tag, Mathias: Deutscher, M. - Birth name of Tag, Mathias: Deutscher, M. AN - OPUS4-23316 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Döring, Ingo T1 - Überarbeitung der Ausnahmen der GGAV T2 - 27. Storck Symposium Internationale Gefahrgut-Tage Hamburg CY - Hamburg, Germany DA - 2011-02-20 PY - 2011 AN - OPUS4-23317 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marwan, J. A1 - Rackwitz, Vanessa T1 - Electrochemical and electron probe microanalysis measurements on nanostructered palladium T2 - 241st ACS National Meeting & Exposition CY - Anaheim, CA, USA DA - 2011-03-27 PY - 2011 AN - OPUS4-23298 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beck, Uwe A1 - Lerche, D. A1 - Rietz, U. A1 - Reiners, Georg T1 - Haftfestigkeitsprüfung mittels Zentrifugenversuch T2 - DGO AnSim Verwertungsworkshop CY - Berlin, Germany DA - 2011-03-23 PY - 2011 AN - OPUS4-23299 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beck, Uwe A1 - Hertwig, Andreas A1 - Stephanowitz, Ralph A1 - Hönig, D. A1 - Domnick, R. A1 - Belzner, M. T1 - Verification and Authentication of Surface- and Layer-embedded Information for Anticouterfeiting Applications by Imaging Ellipsometry T2 - 6th Workshop Ellipsometry CY - Berlin, Germany DA - 2011-02-21 PY - 2011 AN - OPUS4-23300 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Optimierung des Rückbaus / Abbruchs von Gebäuden zur Rückgewinnung und Aufbereitung von hochwertigen RC-Baustoffen N2 - Die Nutzung des Wertstoffpotentials von Abfällen und Reststoffen ist ein Grundpfeiler im Schutz von natürlichen Ressourcen. Dabei ist der Aufbau und Erhalt von Stoffkreisläufen im Baubereich - aufgrund der großen Menge an Baurestmassen - von besonderer Ressourcenrelevanz. Während in Zukunft im Sinne der Nachhaltigkeit schon bei der Errichtung von Gebäuden auch auf Möglichkeiten zur Stoffstromtrennung beim Rückbau geachtet werden sollte, sind die heute rückzubauenden Bauwerke nicht unter diesem Gesichtspunkt errichtet worden. T2 - Baustoff Recycling Forum CY - Nürnberg, Deutschland DA - 10.02.2011 KW - RC-Baustoff Recycling KW - Beton KW - Gips KW - Abbruch PY - 2011 SP - 1 EP - 6 AN - OPUS4-23302 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jacobasch, Stefan T1 - Blind und berührungslos prüfen N2 - RFID-Technologie - Neuartige Radiofrequenz-Identifikations-Transponder könnten die Arbeit von Polizei und Notfalleinsatzkräften nachhaltig erleichtern. Bei der BAM läuft dazu aktuell ein Projekt. KW - Gefahrgut KW - RFID KW - SIGRID PY - 2011 SN - 0016-5808 VL - 2 SP - 24 EP - 26 PB - Storck CY - Hamburg AN - OPUS4-23304 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Werner A1 - Wöhlecke, Andreas T1 - Voraussetzungen für die Zulassung von Geokunststoffen (insbesondere Bewehrungsgittern) für Deponieabdichtungen N2 - Der Fachbeirat beschloss im vergangenen Jahr Zulassungsrichtlinien für Kunststoffdichtungsbahnen, Schutzschichten, Kunststoff-Dränelemente und Geotextilien zum Filtern und Trennen und eine Richtlinie über Anforderungen an Verlegefachbetriebe, die von seinen Arbeitsgruppen vorbereitet worden waren, und nunmehr die Grundlage für die Zulassungstätigkeit bilden. In diesem Beitrag wird im Anschluss an die Ausführungen auf der letzten Fachtagung kurz über wesentliche Anforderungen und Zulassungsvoraussetzungen berichtet. Noch nicht verabschiedet sind die Richtlinien für Dichtungskontrollsysteme und Bewehrungsgitter aus Kunststoff. Auf den Diskussionsstand bei den Anforderungen an die Bewehrungsgitter wird etwas ausführlicher eingegangen, da sich neben den materialtechnischen auch bemessungstechnische Probleme ergeben. T2 - 27. Fachtagung - Die sichere Deponie - Sicherung von Deponien und Altlasten mit Kunststoffen CY - Würzburg, Germany DA - 24.02.2011 KW - Deponieverordnung KW - Zulassung KW - Geokunststoffe KW - Bewehrungsgitter aus Kunststoff PY - 2011 IS - Kap. B SP - 1 EP - 23 CY - Würzburg AN - OPUS4-23305 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hönig, D. A1 - Schneider, S. A1 - Domnick, R. A1 - Belzner, M. A1 - Beck, Uwe A1 - Hertwig, Andreas A1 - Stephanowitz, Ralph A1 - Weise, Matthias ED - Uhlmann, E. T1 - Ellipsometrische Codierung & Fabry-Perot Schichtsysteme mit offenen, versteckten und forensischen Merkmalen zur Produkt-Authentifizierung T2 - 3. Internationaler Kongress - Sichere Identität CY - Berlin, Deutschland DA - 2011-04-05 KW - Ellipsometric encoding KW - Fabry-Perot layer stacks KW - Product authentification PY - 2011 SP - 1 EP - 4(?) CY - Berlin AN - OPUS4-23306 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weißhaupt, Petra A1 - Pritzkow, Wolfgang A1 - Noll, Matthias T1 - Nitrogen metabolism of wood decomposing basidiomycetes and their interaction with diazotrophs as revealed by IRMS N2 - Isotope ratio mass spectrometry (IRMS) is an advanced method to investigate carbon (C) and nitrogen (N) in organic samples. In particular, the N content, its isotope signature and the C/N ratio reveal important facts of nutrient cycling, niche separation and ecological food webs. In this study, the characteristics of N turnover of wood decomposing microorganisms were investigated. The growth of the white rot causing basidiomycete Trametes versicolor is enhanced after addition of ammonia or urea, whereas the brown rot causing Oligoporus placenta is not accelerated. In addition, an interaction of each fungus with atmospheric N2 assimilating (diazotrophic) bacteria was investigated. Cultivation experiments with a gas mixture of 15N2/O2 and subsequent IRMS analysis of dry biomass of the diazotrophs Azotobacter croococcum, Beijerinckia acida and Novosphingobium nitrogenifigens revealed that they assimilated up to 12% of their N from N2. The experiments reflected N availability as a prerequisite for efficient growth of decomposing basidiomycetes and diazotrophs. Fungal–bacterial co-cultivation experiments showed that depending on the growth characteristics and bacterial N2 assimilation activity N is transferred from certain bacteria into fungal biomass. Thus, the experiments gave a first indication of an interaction between wood decomposing basidiomycetes and diazotrophs, which is a novel pathway of fungal N acquisition. KW - IRMS KW - Isotope labeling KW - Microbial interaction KW - N2 assimilation KW - Nitrogen KW - Wood decomposing basidiomycetes PY - 2011 DO - https://doi.org/10.1016/j.ijms.2010.12.011 SN - 0168-1176 SN - 0020-7381 SN - 1387-3806 SN - 1873-2798 VL - 307 IS - 1-3 SP - 225 EP - 231 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-23307 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Aichner, Bernhard A1 - Lehnik-Habrink, Petra A1 - Hein, Sebastian A1 - Bussian, B A1 - Bremser, Wolfram A1 - Nehls, Irene T1 - Monitoring organic pollutants (PAHs, PCBs, OCPs) in German forest soils T2 - IMOG (International Meeting on Organic Geochemistry) CY - Interlaken, Switzerland DA - 2011-09-18 PY - 2011 AN - OPUS4-23278 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kindrachuk, Vitaliy A1 - Fedelich, Bernard A1 - Becker, M. T1 - Simulation of non-isothermal mechanical tests on a single crystal nickel-basis superalloy T2 - 2nd International Conference on Material Modelling CY - Paris, France DA - 2011-08-31 PY - 2011 AN - OPUS4-23279 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jakubcová, Petra A1 - Adomat, Dirk A1 - Ramge, Peter A1 - Rübner, Katrin T1 - New lightweight aggregates from building waste - A new raw material for lightweight concrete N2 - Materials such as masonry rubble are potential raw materials for the production of lightweight Aggregates for use in lightweight concretes. Their excellent technical charateristics makes them an attractive substitute for natural expanded day granules. The lightweight concretes made from these new aggregates show similar properties to those made with conventional expanded clays. KW - Sekundärrohstoffe KW - Sekundäre Gesteinskörnung KW - Recycling KW - Leichtbeton PY - 2011 SN - 0930-3847 VL - 2 SP - 35 EP - 39 PB - Vincentz CY - Hannover AN - OPUS4-23280 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pham-Van, S. A1 - Hinkelmann, R. A1 - Nehrig, Marko A1 - Martinez, I. T1 - A comparison of model concepts and experiments for seepage processes through a dike with a fault zone N2 - eepage processes through a dike with a fault zone on the landside and on the seaside are numerically and experimentally investigated. The numerical simulation is based on a two-phase (water-gas) flow model concept for porous media. Different discrete model concepts accounting for the fault zones are compared among each other and with the experiments. A good agreement between experimental and numerical results was obtained when the fault zones were discretized with 1D elements or with highly resolved 2D elements. We generally recommend choosing 1D elements. When the fault zone is modeled as an open pipe, the seepage velocity is considerably overestimated. Concerning dike stability, a fault zone on the landside is much worse compared to a fault zone on the seaside. KW - Fault zones KW - Fractured-porous media KW - Water-gas flow KW - Numerical modelling KW - Dike PY - 2011 DO - https://doi.org/10.1080/19942060.2011.11015359 SN - 1997-003X SN - 1994-2060 VL - 5 IS - 1 SP - 149 EP - 158 PB - CSE Dept., the H.K. PolyU CY - Hong Kong AN - OPUS4-23281 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Gablenz, Carl A1 - Spaltmann, Dirk T1 - Das CargoLifter Ballonkransystem - der 'CargoLifter Lufthaken' ist da! T2 - 19. Internationale Kranfachtagung - Der Kran und sein Umfeld in Industrie und Logistik CY - Magdeburg, Germany DA - 2011-03-31 PY - 2011 AN - OPUS4-23284 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Beck, Uwe A1 - Reiners, Georg A1 - Lerche, D. A1 - Rietz, U. A1 - Niederwald, H. T1 - Quantitative adhesion testing of optical coatings by means of centrifuge technology N2 - Although adhesion testing of coatings is of fundamental interest for quality assurance, it is still a challenge regarding reliable quantitative results. Because of the huge variety of coating/ substrate systems in terms of materials and thickness range, adhesion tests display the same variety as coating/substrate systems. Some tests are qualitative, many are quantitative but except for the pull (DIN EN ISO 15870) and pull-off test (DIN EN ISO 4624) adhesion is not measured in terms of force per area. For optical coatings, the standardized tests according to ISO 9211-4 apply, i.e. abrasion tests (cheese cloth or eraser test) and adhesion tests (tape or cross-hatch test) with different degrees of severity. Instead of the adhesion strength, all these single-sample tests provide only quantitative information on the abrasion or adhesion resistance of a particular coating/ substrate system. The centrifuge test has manifold advantages. First, it can be easily run as multiple-sample test. Second, adhesion strength is measured in absolute numbers (N/mm2). Third, the centrifuge test requires only a one-sided sample support instead of a two-sided sample clamping as the pull- and pull-off test do. Fourth, it is much easier and faster than many other tests. Fifth, the centrifuge technology additionally enables tests under defined climates or harsh environments. Last but not least, versatile test conditions (alternating loads at various load rates) important to fatigue testing can be easily realized by varying the number of revolutions. The centrifuge test was applied to the testing of optical coatings on glass and CaF2. It could be shown that there are significant advantages compared to other tests. In particular, the centrifuge test was able to discriminate the adhesion strength for coating/substrate systems until failure which all passed the standardized tests of ISO 9211-4. KW - Adhesion strength KW - Bonding strength KW - Optical coatings KW - Pull-off test KW - Centrifuge test KW - Quantitative adhesion testing PY - 2011 DO - https://doi.org/10.1016/j.surfcoat.2011.02.016 SN - 0257-8972 VL - 205 IS - Supplement 2 SP - S182 EP - S186 PB - Elsevier Science CY - Lausanne AN - OPUS4-23285 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scholz, Christian A1 - Spaltmann, Dirk A1 - Woydt, Mathias T1 - Slip-rolling resistance of thin films and high toughness steel substrates under high Hertzian contact pressures N2 - Diamond-like carbon (DLC) coatings are perceived as part of a strategy for low frictional tribosystems. Especially the automotive industry anticipates a benefit in applying such coatings in association with the lightweight construction of mechanical parts, for instance in gear and engine components. Therefore, in previous investigations amorphous carbon (a-C) and tetragonal amorphous carbon (ta-C) coatings were inspected. For up to ten million cycles at Hertzian contact pressures P0max of 2.9 GPa it was shown that these coatings are slip-rolling resistant not only at room temperature in the presence of unaddivated paraffin oil, but also up to 120 °C oil temperature. The steel substrates in this investigation were made of the hardened and tempered steels 100Cr6H and Cronidur 30. The aim of the current work is manifold. The Hertzian contact pressures should be increased up to P0max of 4.2 GPa by using new steel metallurgies as substrates for thin film coatings. These steel metallurgies are also assessed, if they can compete as uncoated couples. Two high toughness spring steels and an ultra-high toughness aerospace steel were tested in a twin disc tribometer of the Amsler type as well as in an Optimol 2Disk test rig under mixed/boundary conditions in a factory fill SAE 0W-30 engine oil. Different factors such as influences of the lubrication, surface chemistry and wear behaviour were investigated. KW - Slip-rolling KW - High toughness steel KW - DLC KW - ZrCN KW - Thin film coating KW - High pressure PY - 2011 DO - https://doi.org/10.1016/j.wear.2011.01.005 SN - 0043-1648 VL - 270 IS - 7-8 SP - 506 EP - 514 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-23286 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fischer, Joachim A1 - Burkert, Andreas A1 - Mietz, Jürgen T1 - Case studies of stainless steel corrsoion in indoor swimming pool environments N2 - In indoor swimming pools stainless steels are used not only due to structural and economic reasons but also due to aesthetic considerations. And therefore not only safety relevant load bearing components have to fulfil their tasks but also the visual appearance should be free of any staining. In a lot of cases basic requirements (e.g. design criteria, material selection and maintenance) being essential parts of technical regulations were not taken into account. Typical case studies with explanation of the cause of the corrosion problems and possibilities to prevent them are shown in the present paper. KW - Stainless steel KW - Atmospheric corrosion KW - Indoor swimming pools PY - 2011 DO - https://doi.org/10.1179/174327809X409150 SN - 1478-422X VL - 46 IS - 1 SP - 76 EP - 79 PB - Maney Publishing CY - London, UK AN - OPUS4-23287 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kuhlich, Paul A1 - Emmerling, Franziska A1 - Piechotta, Christian A1 - Nehls, Irene T1 - Methyl 3,5,5,6,8,8-hexamethyl-5,6,7,8-tetrahydronaphthalene-2-carboxylate (AHTN-COOMe) N2 - Crystals of the title compound, C18H26O2, were grown from ethyl acetate. Due to the racemic precursor, the title compound is also obtained as a racemate. Disorder was observed during structure refinement, originating from two possible half-chair conformations of the non-aromatic ring. The disorder was refined by introducing split positions in the cyclo-hexane ring regarding the two possible R and S-enantiomers at the chiral CH group [ratio 0.744 (3):0.256 (3)]. The crystal structure features pairs of inversion-related molecules connected by pairs of non-classical C–H···O hydrogen bonds. KW - AHTN KW - Tonalide KW - Cyclic musk KW - AHTN-COOMe KW - Disinfection by-product KW - Esterification PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-232769 DO - https://doi.org/10.1107/S1600536811002601 SN - 1600-5368 VL - E67 IS - 2 SP - o485, sup-1 EP - sup-11 PB - Munksgaard CY - Copenhagen AN - OPUS4-23276 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan A1 - Rübner, Katrin A1 - Meng, Birgit T1 - Ganzheitliche Eignungsbewertung potenzieller Recyclingbereiche für Mauerwerksbruch T2 - 2. Symposium "Rohstoffeffizienz und Rohstoffinnovationen" CY - Nuremberg, Germany DA - 2011-02-10 PY - 2011 AN - OPUS4-23277 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bremser, Wolfram T1 - Normalisation in multi-channel GC analysis of gases T2 - Int. Conference GAS 2011 CY - Rotterdam, Netherlands DA - 2011-02-09 PY - 2011 AN - OPUS4-23258 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Leach, R.K. A1 - Boyd, R. A1 - Burke, T. A1 - Danzebrink, H.-U. A1 - Dirscherl, K. A1 - Dziomba, T. A1 - Gee, M. A1 - Koenders, L. A1 - Morazzani, V. A1 - Pidduck, A. A1 - Roy, D. A1 - Unger, Wolfgang A1 - Yacoot, A. T1 - The European nanometrology landscape N2 - This review paper summarizes the European nanometrology landscape from a technical perspective. Dimensional and chemical nanometrology are discussed first as they underpin many of the developments in other areas of nanometrology. Applications for the measurement of thin film parameters are followed by two of the most widely relevant families of functional properties: measurement of mechanical and electrical properties at the nanoscale. Nanostructured materials and surfaces, which are seen as key materials areas having specific metrology challenges, are covered next. The final section describes biological nanometrology, which is perhaps the most interdisciplinary applications area, and presents unique challenges. Within each area, a review is provided of current status, the capabilities and limitations of current techniques and instruments, and future directions being driven by emerging industrial measurement requirements. Issues of traceability, standardization, national and international programmes, regulation and skills development will be discussed in a future paper. KW - Nanotechnology KW - Metrology KW - Chemistry KW - Surface analysis PY - 2011 DO - https://doi.org/10.1088/0957-4484/22/6/062001 SN - 0957-4484 SN - 1361-6528 VL - 22 IS - 6 SP - 062001-1 - 062001-15 PB - IOP Publishing Ltd. CY - Bristol AN - OPUS4-23259 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häcker, Ralf A1 - Memhard, D. A1 - Knothe, Esther A1 - Andrieux, F. T1 - Entwicklung und Verifikation von Materialmodellen und numerischen Methoden zur Vorhersage der Containmentsicherheit beim Bersten von Laufrädern in Abgasturboladern (ATL) T2 - Informationstagung Turbomaschinen, Frühjahrstagung 2011 CY - Bad Neuenahr, Germany DA - 2011-03-17 PY - 2011 AN - OPUS4-23260 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias A1 - Stark, Wolfgang A1 - Wolff, Dietmar T1 - Untersuchung des Tieftemperaturverhaltens von Elastomeren im Dichtungseinsatz T2 - Polymerwissenschaftliches Seminar des Fachgebietes Polymertechnik/-physik der TU-Berlin CY - Berlin, Germany DA - 2011-02-17 PY - 2011 AN - OPUS4-23288 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Denkler, Tilman T1 - Project management using an internet-platform based on MS SharePoint N2 - - Project description - Challenges related to project coordination and information exchange - Presentation of web-platform as solution T2 - EuropeAid-Project "Strengthing of the BiH accreditation system" 5th Steering Committee Meeting CY - Sarajevo, Bosnia and Herzegovina DA - 2011-02-03 PY - 2011 AN - OPUS4-23290 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn A1 - Rosenfeld, A. A1 - Krüger, Jörg ED - Panchenko, V. ED - Mourou, G. ED - Zheltikov, A. M. T1 - Femtosecond laser-induced periodic surface structures: recent approaches to explain their sub-wavelength periodicities N2 - The formation of laser-induced periodic surface structures (LIPSS) upon irradiation of semiconductors and dielectrics by linearly polarized high-intensity Ti:sapphire fs-laser pulses (τ ~100 fs, λ ~800 nm) is studied experimentally and theoretically. In the experiments, two different types of LIPSS exhibiting very different spatial periods are observed (socalled LSFL – low spatial frequency LIPSS, and HSFL - high spatial frequency LIPSS), both having a different dependence on the incident laser fluence and pulse number per spot. The experimental results are analyzed by means of a new theoretical approach, which combines the generally accepted LIPSS theory of J. E. Sipe and co-workers [Phys. Rev. B 27, 1141-1154 (1983)] with a Drude model, in order to account for transient changes of the optical properties of the irradiated materials. The joint Sipe-Drude model is capable of explaining numerous aspects of fs-LIPSS formation, i.e., the orientation of the LIPSS, their fluence dependence as well as their spatial periods. The latter aspect is specifically demonstrated for silicon crystals, which show experimental LSFL periods Λ somewhat smaller than λ. This behaviour is caused by the excitation of surface plasmon polaritons, SPP, (once the initially semiconducting material turns to a metallic state upon formation of a dense free-electron-plasma in the material) and the subsequent interference between its electrical fields with that of the incident laser beam, resulting in a spatially modulated energy deposition at the surface. Upon multi-pulse irradiation, a feedback mechanism, caused by the redshift of the resonance in a grating-assisted SPP excitation, is further reducing the LSFL spatial periods. The SPP-based mechanism of LSFL successfully explains the remarkably large range of LSFL periods between ~0.6 λ and λ. T2 - LAT 2010 - International Conference on Lasers, Applications, and Technologies CY - Kazan, Russia DA - 23.08.2010 KW - Femtosecond laser ablation KW - Laser-induced periodic surface structures (LIPSS) KW - Surface plasmon polaritons KW - Second harmonic generation (SHG) KW - Silicon KW - Semiconductors KW - Dielectrics PY - 2011 DO - https://doi.org/10.1117/12.879813 SN - 0277-786X N1 - Serientitel: Proceedings of SPIE – Series title: Proceedings of SPIE VL - 7994 SP - 79940M-1 EP - 79940M-10 CY - Bellingham, USA AN - OPUS4-23291 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grätz, Rainer T1 - Konformitätsbewertung mechanischer Ex-Betriebsmittel T2 - 36. Heilbronner Ex-Schutz-Seminar "Planen, Errichten und Betreiben von Anlagen in explosionsgefährdeten Betriebsstätten" CY - Heilbronn, Germany DA - 2011-02-23 PY - 2011 AN - OPUS4-23294 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nooke, Alida A1 - Krause, Andreas A1 - Krüger, Hannes A1 - Lohse, Volkmar A1 - Hertwig, Andreas A1 - Beck, Uwe A1 - Steinbach, J. T1 - Gas sensing and monitoring with ellipsometry on modified gold layers T2 - 6th Workshop on ellipsometry, TU Berlin CY - Berlin, Germany DA - 2011-02-21 PY - 2011 AN - OPUS4-23295 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppen, Robert A1 - Koch, Matthias A1 - Rasenko, Tatjana T1 - Neues Analysenverfahren zur Ermittlung aktueller Acrylamidbelastungen in ausgewählten Lebensmitteln T2 - 40. Deutscher Lebensmittelchemikertag 2011 CY - Halle (Saale), Germany DA - 2011-09-12 PY - 2011 AN - OPUS4-23296 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marwan, J. A1 - Rackwitz, Vanessa T1 - Electrochemical and electron probe microanalysis measurements on nanostructered palladium T2 - American Physical Society March Meeting 2011 CY - Dallas, TX, USA DA - 2011-03-21 PY - 2011 AN - OPUS4-23297 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröder, Volkmar T1 - Stoffliche Aspekte des Explosionsschutzes im Bereich der Prozess- und Anlagensicherheit T2 - Safety and Security in der Anlagen-, Produkt- und Verkehrssicherheit 2011 CY - Brandenburg an der Havel, Germany DA - 2011-01-27 PY - 2011 AN - OPUS4-23238 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Traub, Heike A1 - Kipphardt, Heinrich A1 - Jakubowski, Norbert T1 - Bestimmung von Elementspuren in Niobpentoxid-Pulver mit LA-ICP-MS T2 - CANAS 2011 CY - Leipzig, Germany DA - 2011-03-13 PY - 2011 AN - OPUS4-23241 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Einfluss ausgewählter Modifikationen der Mischungszusammensetzung auf die Eigenschaften von Instandsetzungsmörteln T2 - 2. Kolloquium "Erhaltung von Bauwerken" CY - Ostfildern, Germany DA - 2011-01-25 PY - 2011 AN - OPUS4-23245 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schnell, A. A1 - Müller, A. A1 - Rübner, Katrin A1 - Daschner de Tercero, M. A1 - Teipel, U. T1 - Aufbaukörnungen - Heterogener Bauschutt als Rohstoff für die Herstellung von Leichtgranulaten T2 - Symposium "Rohstoffeffizienz und Rohstoffinnovationen" CY - Nuremberg, Germany DA - 2011-02-10 PY - 2011 AN - OPUS4-23247 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Xu, H.-J. A1 - Mack, J. A1 - Descalzo López, Ana Belén A1 - Shen, Z. A1 - Kobayashi, N. A1 - You, X.-Z. A1 - Rurack, Knut T1 - meso-Aryl phenanthroporphyrins: Synthesis and spectroscopic properties N2 - The successful synthesis of tetraphenyltetraphenanthroporphyrin (TPTPhenP; 5a) in 2006 under modified Rothemund–Lindsey conditions yielded a tetraphenyl porphyrinoid with a B band redshifted to an unprecedented 576 nm. Radially symmetric fused-ring expansion of tetraphenylporphyrin with phenanthrene moieties results in very deep saddling due to steric crowding and very marked redshifts of the Q and B (or Soret) porphyrinoid absorption bands. The extent to which the TPTPhenP structure can be further modified is explored, and the optical properties of TPTPhenPs are analyzed based on a perimeter model approach that makes use of time-dependent DFT calculations and magnetic circular dichroism spectroscopy and also based on a detailed analysis of the fluorescence emission. Attempts to introduce substituents at the ortho and meta positions of the meso-phenyl groups and to insert a central metal proved unsuccessful. The synthesis of a series of TPTPhenPs with strong electron-withdrawing (—CN, —NO2) and -donating (—CH3, —N(CH3)2) substituents at the para positions of the meso-phenyl rings is reported. Marked redshifts of the main spectral bands were consistently observed. The most pronounced spectral changes were observed with —N(CH3)2 groups (5i) due to a marked destabilization of the HOMO, which has large MO coefficients on the meso-carbon atoms. Protonation of 5i at both the ligand core and at the —N(CH3)2 groups resulted in unprecedented Q00 band absorption at wavelengths greater than 1200 nm. KW - Charge transfer KW - Circular dichroism KW - Dyes/pigments KW - Porphyrinoids KW - Protonation PY - 2011 DO - https://doi.org/10.1002/chem.201002596 SN - 0947-6539 SN - 1521-3765 VL - 17 IS - 32 SP - 8965 EP - 8983 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-24208 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Larissa A1 - Jakubowski, Norbert A1 - Hayen, H. A1 - Roos, P.H. T1 - Iodination of proteins, proteomes and antibodies with potassium triodide for LA-ICP-MS based proteomic analyses N2 - A fast and mild method for iodine labelling of proteins is presented which is specifically designed and optimized for laser ablation (LA-)ICP-MS based proteomics. Single proteins (lysozyme, bovine serum albumin, cytochrome c and β-casein), whole proteomes (microsomal proteome of rats) and antibodies (anti-bovine casein, anti-bovine serum albumin) can be efficiently iodinated by means of potassium triiodide with minimal losses of antigen properties and antibody binding to iodinated proteins. A comparison with iodination by use of IODO-Beads is presented and it is shown that triiodide labelling is a fast, cheap and less laborious alternative without compromising the analytical figures of merit. PY - 2011 DO - https://doi.org/10.1039/c1ja10090d SN - 0267-9477 SN - 1364-5544 N1 - Geburtsname von Müller, Larissa: Wäntig, L. - Birth name of Müller, Larissa: Wäntig, L. VL - 26 SP - 1610 EP - 1618 PB - Royal Society of Chemistry CY - London AN - OPUS4-24209 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - De Bruyn Ouboter, D. A1 - Schuster, T.B. A1 - Mantion, Alexandre A1 - Meier, W. T1 - Hierarchical organization of purely peptidic amphiphiles into peptide beads N2 - A broad range of new properties is emerging from supramolecular aggregates as they pass beyond the limitations of simple molecules. Self-assembled structures of purely peptidic amphiphiles may exploit such properties to produce biocompatible, smart materials for drug administration. In aqueous media, the solid-phase derived amphiphilic undecapeptide described herein (Ac-X3-gT) forms self-assembled particles of spherical shape with diameters between 200 and 1500 nm, termed 'peptide beads'. The beads result from hierarchical organization of micellar-like structures, a fact determined by a combination of investigations carried out by electron and atomic force microscopy (AFM), static and dynamic light scattering, and small-angle X-ray scattering. These highly ordered structures agree with the concept of multicompartmentization and represent the first example of supramicellar assemblies based purely on peptides. New structural insights, as presented here, allow a better understanding of the beads' capacity to embed hydrophobic and hydrophilic payloads and therefore provide new perspectives for drug delivery applications that may result from this new class of material. KW - Peptide beads KW - Spherical peptide particles KW - Hierarchical self-assembly KW - Multicompartment micelles KW - Purely peptidic amphiphiles PY - 2011 DO - https://doi.org/10.1021/jp203048h SN - 1932-7447 SN - 1089-5639 VL - 115 IS - 30 SP - 14583 EP - 14590 PB - Soc. CY - Washington, DC AN - OPUS4-24212 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wolff, Timo A1 - Malzer, W. A1 - Mantouvalou, I. A1 - Hahn, Oliver A1 - Kanngießer, B. T1 - A new fundamental parameter based calibration procedure for micro X-ray fluorescence spectrometers N2 - Fundamental parameter based quantification of X-ray fluorescence (XRF) measurement data requires an accurate knowledge of the spectrometer parameters, including the spectral distribution of the excitation radiation. In case of micro-XRF where a polycapillary optic is utilized in the excitation channel this distribution is changed due to the transmission properties of the lens. A new calibration procedure, based on fluorescence data of thin standard samples, was developed to determine the excitation spectrum, i.e., the product of the X-ray tube spectrum and the transmission of the used X-ray optic of a micro-XRF setup. The calibration result was validated by the quantitative analyses of certified multi-element reference standards and shows uncertainties in the order of 2% for main components, 10% for minor elements and 25% for trace elements. The influence of secondary order effects like Coster–Kronig transitions and cascade effects is analyzed and the accuracy of fundamental parameters in common databases is discussed. KW - Polycapillary optic KW - Transmission KW - Micro-XRF calibration KW - Reference free quantification PY - 2011 DO - https://doi.org/10.1016/j.sab.2011.01.009 SN - 0584-8547 SN - 0038-6987 VL - 66 IS - 2 SP - 170 EP - 178 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-24213 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gaul, Holger A1 - Weber, Gert A1 - Rethmeier, Michael T1 - Influence of HAZ cracks on fatigue resistance of resistance spot welded joints made of advanced high strength steels N2 - A method is reported with which heat affected zone (HAZ) cracks in a specific region of spot welded joints, made of advanced high strength steels, could be realised. The influence of HAZ cracks on the fatigue behaviour, which is the focus of the contribution, was studied by evaluating the stiffness characteristics as a function of the number of cycles N in comparison with crack-free specimens, i.e. by analysing HAZ and fatigue cracks on the specimen surface and the surface of fatigue fractures containing beach marks. It was found that the fatigue cracks are not initiated at the HAZ cracks. The number of cycles to failure Nf is not significantly reduced for specimens with HAZ cracks. Overall, the examinations did not reveal any influence of HAZ cracks on the fatigue strength of resistance spot welded joints. KW - Discontinuities KW - AHSS KW - HAZ crack KW - Spot welding KW - Advanced high strength steels KW - Fatigue PY - 2011 DO - https://doi.org/10.1179/1362171810Y.0000000031 SN - 1362-1718 SN - 1743-2936 VL - 16 IS - 5 SP - 440 EP - 445 PB - Maney CY - London AN - OPUS4-24214 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Otremba, Frank A1 - Balke, Christian A1 - Butz, Manuel A1 - Zur, Malte T1 - Ermittlung von Wärmeübergangszahlen eines sich im Feuer befindlichen Tanks N2 - Für die Bewertung der Integrität von Tanks ist die detaillierte Kenntnis der belastungsrelevanten Parameter unabdingbar. Die Wärmeübergangszahl a ist eine derartige Größe. Die Wärmeübergangszahl bestimmt direkt die Größe der vorhandenen Beanspruchungen im Tank. Insofern sollte die Wärmeübergangszahl bekannt sein. Aus diesem Grund wurden experimentelle Untersuchungen durchgeführt. Für einen sich im Feuer befindlichen Tank ergibt sich die Wärmeübergangszahl zu 50 W/m2K. Auf dieser Basis konnten die bereits durchgeführten experimentellen Untersuchungen mithilfe der Methode der finiten Elemente nachgerechnet werden. Die dabei erzielten Ergebnisse sind infolge der getroffenen modelltechnischen sowie thermodynamischen Vereinfachungen als zufriedenstellend zu bezeichnen. In einem nächsten Schritt wird an einer verbesserten Modellierung sowie thermodynamischen Beschreibung der Verhältnisse im Tank gearbeitet. PY - 2011 SN - 2191-0073 VL - 1 IS - 7/8 SP - 22 EP - 24 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-24216 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger T1 - Wie findet der Hausbock zum Holz - Neues von einem altbekannten Schädling T2 - Einladungdvortrag zum Verbandstag es Deutschen Holz- und Bautenschutzverbandes CY - Suhl, Germany DA - 2011-09-15 PY - 2011 AN - OPUS4-24217 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Torge, Manfred A1 - Krug, Sonja A1 - Bücker, Michael A1 - Scharf, Holger A1 - Witthuhn, Heike T1 - Investigation of Mercury Emissions of Historical Tin Amalgam Mirrors T2 - ART 2011 "International conference on non-destructive investigation and microanalysis for the diagnostics and conservation of cultural and environmental heritage CY - Florence, Italy DA - 2011-04-13 PY - 2011 AN - OPUS4-23918 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Goedecke, Thomas A1 - Menrad, Andreas A1 - Bethke, John T1 - Application of nondestructive testing - Methods for packaging examination N2 - Nondestructive testing (NDT) methods are applicable in many ways for defect detection as well as optimization of packaging production processes. The visual inspection method is the technique which is mostly used, although neither the customer nor a skilled inspector may be aware of this. Techniques like ultrasound for wall thickness measurement, the application of x-ray techniques or the use of dye penetrant techniques for crack detection are rather well known to the NDT family. However, acoustic emission techniques can also be helpful for the characterization of packaging materials. In this paper the employment of x-ray computer tomography (CT) for measurement of wall thickness in plastic jerrycans, especially on the edges, and its possible optimization of production processes will be discussed. A comparison of the CT and ultrasonic examinations of wall thickness and the reliability of this measured data are also important points for the discussion, especially if some safety factors can be derived from the results. The leakage test is also good for jerrycans, IBCs or other kinds of drums for the transportation and storage of dangerous goods. The disadvantage of this kind of test is that a lack of quality, e.g. wall thickness deterioration, cannot be detected if the wall thickness withstands the internal pressure. Therefore, especially for Quality assurance, the other, previously mentioned techniques are better for a statistical assessment of a batch. This paper is focused on the comparison of different NDT results with special emphasis on the large range of material mechanical properties. T2 - 25th IAPRI Symposium on Packaging CY - Berlin, Germany DA - 16.05.2011 KW - Materialeigenschaft KW - Zerstörungsfreie Prüfung KW - Computertomographie KW - Kunststoffbehälter PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-239191 SN - 978-3-940283-31-3 VL - 126 SP - 1 EP - 7 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-23919 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Berger, Anka A1 - Krüger, Simone A1 - Krause, Ulrich ED - Kühle-Weidemeier, M. T1 - Self-ignition of deposits containing recycling materials - an underestimated phenomenon N2 - Fires on waste dumps, surface landfills, Underground stowing or storage facilities of Recycling factories may have multiple harmful effects on individuals on site and on environment. Possibly several tens of thousands of tons flare up plunging vast areas in smoke and releasing large amounts of flue gases. Experience shows that fire fighting takes days or even weeks and moreover, as long as hidden glowing nests exist fires may break out repeatedly weeks or months later. In the light of this, fire prevention is much easier to manage than extinction. It is of internst to identify the geometrical and physical conditions under which the mid-term or long-term storage of recycling materials can be performed avoiding self-ignition. Our Guideline presents a novel method developed at BAM which combines experimental tests on lab-scale with numerical simulations in Order to obtain permissible geometries of deposits and storage times at which self-ignition can be certainly avoided (Berger 2010). T2 - Waste-to-resources 2011 - 4th International Symposium MBT & MRF CY - Hannover, Germany DA - 24.05.2011 KW - Self-ignition KW - Hot storage tests KW - Numerical simulations KW - FTIR spectroscopy KW - Guideline PY - 2011 SN - 978-3-86955-747-2 SP - 1 EP - 13 PB - Cuvillier AN - OPUS4-23920 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Berger, Wolfgang A1 - Kalbe, Ute A1 - Krüger, Oliver A1 - Hennecke, D. A1 - Kördel, W. T1 - Ergebnisse der Untersuchungen zur Robustheit des Schüttelverfahrens E DIN 19527 für prioritäre organische Schadstoffe in Böden/Bodenmaterialien T2 - 25. Sitzung des Fachbeirates Bodenuntersuchung des BMU/UBA CY - Dessau-Roßlau, Germany DA - 2011-06-21 PY - 2011 AN - OPUS4-23926 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Werner T1 - Zur Bemessung der Verankerung von Bewehrungsgittern aus Kunststoff beim Schutz von Böschungen vor hangparallelem Gleiten N2 - Bewehrungsgitter aus Kunststoff, die zum Schutz vor hangparallelem Gleiten auf langen und steilen Böschungen eingebaut werden, müssen sicher verankert werden. Für den Entwurf und die Berechnung der Verankerung sind bestimmte Regeln gebräuchlich. An Hand von Modellen für die Wechselwirkung zwischen Füllboden und Bewehrungsgitter wird diskutiert, welche physikalischen Annahmen und Vereinfachungen in diese Bemessungsregeln eingehen. Dabei wird gezeigt, dass das bisher benutzte Bemessungskonzept ohne Einschränkung nur auf eine spezielle Klasse von Bewehrungsgittern anwendbar ist, deren Herausziehwiderstand überwiegend von Effekten der 'Oberflächenreibung' zwischen Bodenpartikeln und Längselementen des Gitters bedingt ist ('Reibungsgitter'). Für die Bemessung muss hier der Verbundbeiwert dieser reinen Oberflächenreibung verwendet werden. Bei Bewehrungsgittern, wo ein Erddruck, der sich vor den Querelementen des Gitters aufbaut, maßgeblich zum Herausziehwiderstand beiträgt, ist die Festigkeit der Verbindungsstellen zwischen Längs- und Querelementen von entscheidender Bedeutung für eine sichere Verankerung ('Erddruckgitter'). Die Zusammenhänge zwischen mechanischem Verhalten der Verbindungsstellen, Dehnbarkeit der Längselemente, Oberflächenreibung und maximaler Herausziehkraft werden beispielhaft aufgezeigt. Die Festlegung eines Bemessungswiderstands der Verbindungsstellen, der grundsätzlich nicht überschritten werden darf, erfordert eine Modifikation des Bemessungskonzepts. Zwei Fälle können unterschieden werden: Bei Böden mit hinreichend geringer innerer Reibung und geringer Auflast, wo der maximal mobilisierbare Erdwiderstand die zulässige Festigkeit der Verbindungsstelle nicht übersteigen kann, können die Bemessungsregeln noch angewendet werden. In allen anderen Fällen nicht mehr: Der Bemessungswiderstand der Verbindungsstelle setzt nämlich der möglichen aktivierbaren Verankerungslänge eine obere Grenze. Es können dann auch nur Zugkräfte bis zu einer bestimmten Stärke verankert werden, völlig unabhängig davon, wie groß die Zugfestigkeit des Bewehrungsgitters ist. Nur bei Beachtung dieser Grenzen ist eine langfristig sichere Verankerung möglich. KW - Bewehrungsgitter aus Kunststoff KW - Geogitter KW - Deponieoberflächenabdichtung KW - Verankerung KW - Bemessung KW - EBGEO KW - Gleiten KW - Hangparalleles KW - Herausziehkraft KW - Langzeitverhalten KW - Bewehrte Erde KW - Geogrids KW - Landfill capping system KW - Slope stability KW - Pull-out strength KW - Anchoring KW - Long-term behavior KW - Design with reinforced soil KW - Bodenmechanik KW - Baustoffe KW - Soil mechanics KW - Building materials PY - 2011 DO - https://doi.org/10.1002/bate.201101472 SN - 0932-8351 SN - 1437-0999 SN - 0005-6820 SN - 0341-1052 SN - 0932-6359 VL - 88 IS - 6 SP - 347 EP - 361 PB - Ernst & Sohn CY - Berlin AN - OPUS4-23927 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, B.V.K.J. A1 - Fechler, N. A1 - Falkenhagen, Jana A1 - Lutz, J.-F. T1 - Controlled folding of synthetic polymer chains through the formation of positionable covalent bridges N2 - Covalent bridges play a crucial role in the folding process of sequence-defined biopolymers. This feature, however, has not been recreated in synthetic polymers because, apart from some simple regular arrangements (such as block co-polymers), these macromolecules generally do not exhibit a controlled primary structure—that is, it is difficult to predetermine precisely the sequence of their monomers. Herein, we introduce a versatile strategy for preparing foldable linear polymer chains. Well-defined polymers were synthesized by the atom transfer radical polymerization of styrene. The controlled addition of discrete amounts of protected maleimide at precise times during the synthesis enabled the formation of polystyrene chains that contained positionable reactive alkyne functions. Intramolecular reactions between these functions subsequently led to the formation of different types of covalently folded polymer chains. For example, tadpole (P-shaped), pseudocyclic (Q-shaped), bicyclic (8-shaped) and knotted (α-shaped) macromolecular origamis were prepared in a relatively straightforward manner. KW - Copolymerization KW - Chain folding KW - SEC KW - NMR KW - FT-IR KW - LAC KW - MALDI PY - 2011 DO - https://doi.org/10.1038/NCHEM.964 SN - 1755-4330 SN - 1755-4349 VL - 3 SP - 234 EP - 238 PB - Nature Publishing Group CY - London, UK AN - OPUS4-23888 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Noack, Volker A1 - Völzke, Holger T1 - Storage Facilities at Sayda Bay T2 - 52. INMM-Tagung CY - Palm Desert, CA, USA DA - 2011-07-17 PY - 2011 AN - OPUS4-23891 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hennig, Andreas A1 - Hoffmann, Angelika A1 - Borcherding, H. A1 - Thiele, T. A1 - Schedler, U. A1 - Resch-Genger, Ute T1 - Simple colorimetric method for quantification of surface carboxy groups on polymer particles N2 - We present a novel, simple, and fast colorimetric method to quantify the total number of carboxy groups on polymer microparticle and nanoparticle surfaces. This method exploits that small divalent transition metal cations (M2+ = Ni2+, Co2+, Cd2+) are efficiently bound to these surface functional groups, which allows their extraction by a single centrifugation step. Remaining M2+ in the supernatant is subsequently quantified spectrophotometrically after addition of the metal ion indicator pyrocatechol violet, for which Ni2+ was identified to be the most suitable transition metal cation. We demonstrate that the difference between added and detected M2+ is nicely correlated to the number of surface carboxy groups as determined by conductometry, thereby affording a validated measure for the trueness of this procedure. The variation coefficient of ~5% found in reproducibility studies underlines the potential of this novel method that can find conceivable applications for the characterization of different types of poly(carboxylic acid)-functionalized materials, e.g., for quality control by manufacturers of such materials. KW - Polymer surface KW - Complexometry KW - Quantification KW - Pyrocatechol violet PY - 2011 DO - https://doi.org/10.1021/ac2007619 SN - 0003-2700 SN - 1520-6882 VL - 83 IS - 12 SP - 4970 EP - 4974 PB - American Chemical Society CY - Washington, DC AN - OPUS4-23892 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Finke, C.-H. A1 - Nehls, Irene A1 - Erek, G. A1 - Piechotta, Christian A1 - Brinkmann, P.-G. J. T1 - Bisphenol A release from fissure sealants T2 - IAPD Interdisciplinary Approach to Paediatric Dentistry CY - Athens, Greece DA - 2011-06-15 PY - 2011 AN - OPUS4-23893 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vela-Wallenschus, Iris A1 - Knaust, Christian A1 - Krause, Ulrich T1 - A generic approach for hazard prevention in large storages of combustible wastes T2 - 3rd iNTeg-Risk Conference CY - Stuttgart, Germany DA - 2011-06-06 PY - 2011 N1 - Geburtsname von Vela-Wallenschus, Iris: Vela, I. - Birth name of Vela-Wallenschus, Iris: Vela, I. AN - OPUS4-23894 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ewert, Uwe A1 - Beckmann, Jörg A1 - von Chrzanowski, Lars A1 - Brekow, Gerhard A1 - Brackrock, Daniel T1 - Time of flight diffraction (ToFD) with THz radiation - an alternative to the ultra sound - ToFD technique for non-metallic materials N2 - A time domain spectrometer in the range of 0.5–2 THz was used for time of flight (ToF) measurements of THz pulses for imperfection detection in non metallic materials. The measurements were performed in comparison to the established ultra sound pulse echo (PE) and time of flight diffraction (ToFD) technique. No coupling agent and no contact to the surface is required for THz ToFD measurements. Plastic test specimen with notches, voids and drilled side holes were used to study reflected and diffracted response signals. No major differences were observed between the UT and THz ToFD records for the first surface of the notches, voids and holes. Additionally to the UT records also signals were obtained from its back side and a second raw of holes. The THz measurement is fast and has the potential to substitute UT applications in some industrial areas. Within the German project 'Handheld' the potential for miniaturization of the time domain equipment is explored for efficient application. KW - Spectrometers KW - Ultrasonic diffraction KW - Acoustic signal processing KW - Voids (solid) KW - Terahertz time domain spectroscopy KW - Ultrasonic KW - Time of flight diffraction KW - Non destructive testing KW - Polymers PY - 2011 DO - https://doi.org/10.1063/1.3591898 SN - 0094-243X VL - 1335 SP - 541 EP - 548 PB - American Institute of Physics CY - Melville, NY, USA AN - OPUS4-23895 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koshkina, Olga A1 - Bantz, C. A1 - Lang, Thomas A1 - Würth, Christian A1 - Resch-Genger, Ute A1 - Maskos, Michael T1 - Synthesis and Characterisation of Siloxane Based Nanoparticles for in Vitro studies T2 - Advanced Functional Polymers for Medicine 2011 CY - Enschede, Netherlands DA - 2011-06-15 PY - 2011 AN - OPUS4-23896 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bleul, Regina A1 - Thiermann, Raphael A1 - Bachran, D. A1 - Maskos, Michael T1 - Probing Polymersome-Protein and -Cell Interactions: Structural Characterization and In Vito Studies T2 - Advanced Functional Polymers for Medicine 2011 CY - Enschede, Netherlands DA - 2011-06-15 PY - 2011 AN - OPUS4-23897 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ehrig, Karsten A1 - Goebbels, Jürgen A1 - Meinel, Dietmar A1 - Paetsch, O. A1 - Prohaska, S. A1 - Zobel, Valentin T1 - Comparison of crack detection methods for analyzing damage processes in concrete with computed tomography T2 - International Symposium on Digital Industrial Radiology and Computed Tomography CY - Berlin, Germany DA - 2011-06-20 PY - 2011 AN - OPUS4-23868 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ehrig, Karsten A1 - Staude, Andreas A1 - Goebbels, Jürgen A1 - Bartscher, M. A1 - Koch, M. T1 - Einfluss von Materialkombinationen auf das dimensionelle Messen mit Mikro-Computertomographie am Beispiel eines werkstücknahen Testköpers T2 - DGZfP Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23869 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Matthias A1 - Jann, Oliver A1 - Schneider, Uwe A1 - Krocker, Christian A1 - Kemski, J. A1 - Klingel, R. T1 - Investigations on radon exhalation of different buildings materials T2 - Indoor Air 2011 CY - Austin, TX, USA DA - 2011-06-05 PY - 2011 AN - OPUS4-23871 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Simo, A. A1 - Merk, Virginia A1 - Fenger, R. A1 - Kneipp, Janina A1 - Rademann, K. T1 - Long-term stable silver subsurface ion-exchanged glasses for SERS applications N2 - We report on the formation of silver subsurface ion-exchanged metal oxide (silver SIMO) glasses and their surface-enhanced Raman scattering (SERS) activity. The samples were prepared by a combined thermal and chemical three-step methodology and characterized by transmission electron microscopy (TEM), atomic force microscopy (AFM), environmental electron scanning microscopy (ESEM), and UV/Vis spectroscopy. This unique method provides SERS substrates with protection against contamination and strong, reliable and reproducible SERS enhancement. The Raman enhancement factors of the long-term stable SIMO glasses were estimated to approximately 107. KW - AFM/TEM/SEM KW - Ion-exchange KW - Nanoparticles KW - Glasses KW - Surface-enhanced Raman scattering PY - 2011 DO - https://doi.org/10.1002/cphc.201100098 SN - 1439-4235 N1 - Geburtsname von Merk, Virginia: Joseph, V. - Birth name of Merk, Virginia: Joseph, V. VL - 12 IS - 9 SP - 1683 EP - 1688 PB - Wiley-VCH CY - Weinheim AN - OPUS4-23872 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Heinze, Christoph A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - Influences of mesh density and transformation behavior on the result quality of numerical calculation of welding induced distortion N2 - Welding simulation is a powerful, cost-efficient tool to predict welding induced distortion. Nevertheless, effects on calculation result quality are often unknown, thus, sensitivity analyses should be performed to evaluate the influences of certain parameters on distortion development. In the present paper, a single-layer gas metal arc (GMA) weld of 5 mm thick structural steel S355J2+N is experimentally and numerically investigated. Subsequent to welding, the numerical modeling begins with a mesh analysis based on modal analyses. Hereby, the influence of different coarsening methods and element edge length (EEL) in welding direction on the deformation behavior or the stiffness of the discrete geometry is the focus of the analysis. Secondly, phase transformations in structural steels such as S355J2+N are decisive for final product properties. The sensitivity of welding-induced distortion is examined regarding different continuous cooling transformation (CCT) diagrams for S355J2+N. The present investigations deal with different relevant influences on numerical calculation of welding-induced distortion. The quality and quantity of these effects are clarified based on the experimental and numerical set-up employed. Consequently, prediction of welding-induced distortion is possible and potential for pre-production optimization is present. KW - Welding simulation KW - Gas metal arc welding KW - Welding-induced distortion KW - Mesh analysis KW - CCT sensitivity PY - 2011 DO - https://doi.org/10.1016/j.simpat.2011.05.001 SN - 1569-190X VL - 19 IS - 9 SP - 1847 EP - 1859 PB - Elsevier CY - Amsterdam [u.a.] AN - OPUS4-23874 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rosemann, P. A1 - Bender, S. A1 - Heyn, Andreas A1 - Schmidt, J. T1 - In vitro corrosion and biocompatibility of coated MgCa1.0 magnesium alloys N2 - As bio-absorbable implant material the magnesium alloy Mg-1Ca is able to degrade in-vivo. The mechanical properties of this alloy are similar to those of human bone; both Mg and Ca are essential elements in human body. The main problem is the high corrosion rate of this alloy. Two coating systems based on plasma-chemical oxidation and an organic dip coating are applied onto MgCa1.0 magnesium alloy in order to slow down the corrosion rate. The corrosion behaviour of the coated alloys was investigated with electrochemical noise measurements. The influence of hydrogen evolution and increasing pH-value on the cytotoxicity was examined. The results of these investigations suggest that a combination of both coating systems leads to promising degradation properties. KW - Biocompatibility KW - Biodegradation KW - Magnesium KW - Plasma-Chemical Oxidation PY - 2011 DO - https://doi.org/10.4028/www.scientific.net/MSF.690.409 SN - 0255-5476 VL - 690 SP - 409 EP - 412 PB - Trans Tech Publications CY - Aedermannsdorf, Switzerland AN - OPUS4-23875 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wiegner, Katharina A1 - Nohr, Michael A1 - Farke, M. A1 - Horn, Wolfgang A1 - Kalus, Sabine A1 - Jann, Oliver A1 - Hahn, Oliver T1 - Frische Luft für Museumsvitrinen - Neue Methode zur Untersuchung von Vitrinenbaumaterialien als Beitrag zur Präventiven Konservierung N2 - Nicht nur Schadstoffe aus der Umwelt können Museumsexponate schädigen. Auch interne Schadstoffquellen wie objektimmanente Exhalate und Emissionen von Lösemitteln oder organischen Säuren können den wertvollen Gu¨tern Schaden zufu¨gen. Auf Schadstoffe zu pru¨fen sowie geeignete Messmethoden zu entwickeln und zu optimieren, ist daher von großer Bedeutung. Neuste Forschungen stellen die Autoren vor. KW - VOC KW - Präventive Konservierung KW - Emissionsmessungen KW - AgBB-Schema KW - Ausstellungsvitrinen KW - Verpackungsmaterialien PY - 2011 SN - 0933-4017 VL - 117 IS - 5 SP - 30 EP - 35 PB - Callwey CY - München AN - OPUS4-23877 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Bäßler, Ralph ED - Wieland, H.-J. T1 - Use of higher-alloyed metallic materials and duplex steels for transport tanks of dangerous goods N2 - Compatibility evaluations of selected metallic materials under the influence of dangerous goods are published in the BAM-List - Requirements for Tanks for the Transport of Dangerous Goods” as basis for substance-related prototype approvals for tank Containers designed for the carriage of dangerous goods. There is a request of the tank manufacturing industry and transportation Companies to incorporate additional materials into the BAM-List, especially corrosionresistant materials because of the large number of corrosive dangerous goods. One solution to solve corrosion Problems is to line the tank with a polymeric material, an alternative solution is the application of high-alloyed stainless steels and nickel-based alloys as there are alloy 926 (1.4529), alloy 31 (1.4562) and alloy 59 (2.4605). But there is an interest to use cost-efficient steels with high strength values and concomitant adequate corrosion resistance such as duplex Steel 1.4362 too. This Steel grade was originally developed as a substitute for the austenitic grades 1.4404 and 1.4571. Due to the lower content of the alloy elements nickel and molybdenum this duplex steel is a cost-efficient alternative to molybdenum containing austenite. Due to the limited number of corrosion test results with welded test samples of these high-alloyed materials and the duplex steel under the influence of corrosive dangerous goods a comprehensive test Programme was performed with these materials in Cooperation with ThyssenKrupp VDM and Deutsche Edelstahlwerke GmbH. It can be concluded from the test results that the "superaustenitic steels” 1.4529 and 1.4562 as well as the nickel-based alloy 2.4605 are a really good alternative as tank materials for the transport of dangerous goods in comparison to the lining of the tanks. Due to the reduced alloying content, in particular Nickel (3.7 %) and Molybdenum (0.15 %), a lower resistance of the duplex steel 1.4362 compared to the austenitic CrNiMo-steels was observed in acidic media. The duplex Steel is an alternative to the austenitic steels, especially in alkaline media. The test results are included in the current 10th edition of the BAM-List and therefore available for the costumer. T2 - SCT2011 - 3rd International conference on steels in cars and trucks CY - Salzburg, Austria DA - 06.05.2011 KW - BAM-List KW - Corrosion resistance KW - Dangerous goods KW - Duplex steels KW - Superaustenitic steels KW - Nickel alloy PY - 2011 SN - 978-3-514-00783-3 SP - 29 EP - 37 PB - Stahleisen AN - OPUS4-23859 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Baer, I. A1 - van de Kreeke, Johannes A1 - Linsinger, T.P.J. A1 - Robouch, P. A1 - Raposo, F.C. A1 - de la Calle, B. T1 - IMEP-24 analysis of eight trace elements in toys N2 - The International Measurement Evaluation Program (IMEP) organized the IMEP-24 interlaboratory comparison after reports in the media about high levels of lead in toys. The aim of this comparison was to verify the laboratories' capacity to evaluate trace-element levels in a possible toy-like material according to the European Standard EN 71-3:1994. As test material, it used a former certified reference material containing levels of antimony, arsenic, barium, cadmium, chromium, mercury, lead and selenium around the limits set in the standard. Four expert laboratories confirmed the reference values (Xref) for all elements but Hg, and established a reference value for Hg. The scatter of the results reported by the participants was large, as expected, but showed a close to normal distribution around the reference values for five of the eight trace elements. The spread of results was mainly attributed to sampling and sample preparation. One major issue observed in this exercise was the lack of legislative rules about how to report the result, or, more specifically, the use of the analytical correction, which was introduced in EN 71-3:1994 to achieve consistent interpretation of results and which is to be applied when values are equal to or above the maximum limits set in the standard. Its application by the participants was very inconsistent and led to problems in their evaluation. There is clearly a need for clarification and for more formal regulations with regard to result reporting in order to minimize the risk of confusion. Participants were also asked to give their opinion with regard to the acceptability of the test material for the market. The majority correctly considered the material as non-compliant. However, almost one-third incorrectly assessed the material as compliant. KW - Analytical correction KW - European Standard EN 71-3:1994 KW - Interlaboratory comparison KW - International Measurement Evaluation Program (IMEP) KW - Lead in toys KW - Toy safety KW - Trace element PY - 2011 DO - https://doi.org/10.1016/j.trac.2010.09.007 SN - 0165-9936 SN - 0703-7147 VL - 30 IS - 2 SP - 313 EP - 323 PB - Elsevier CY - Amsterdam AN - OPUS4-23862 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppen, Robert A1 - Krüger, Rita A1 - Koch, Matthias A1 - Bremser, Wolfram A1 - Nehls, Irene T1 - New certified reference materials for mycotoxin analysis in food T2 - Tag der Chemie (Humboldt-Universität zu Berlin) CY - Berlin, Germany DA - 2011-07-13 PY - 2011 AN - OPUS4-23863 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grasse, Fabian A1 - Trappe, Volker A1 - Hickmann, Stefan A1 - Hopmann, Ch. A1 - Michaeli, W. A1 - Lamprecht, L. T1 - Mikroschädigungsakkumulation / Dauerfestigkeitsgrenze in FVK T2 - SPP 1466 Kolloquium CY - Berlin, Germany DA - 2011-07-01 PY - 2011 AN - OPUS4-23864 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scholz, Christian A1 - Woydt, Mathias T1 - Höchstbelastbare Wälzkontakte mit geringer Misch-/Grenzreibungszahl - Werkstoff-, Oberflächen-, Additiveinfluss T2 - 7. Arnold Tross Kolloquium CY - Hamburg, Germany DA - 2011-06-17 PY - 2011 AN - OPUS4-23865 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiegner, Katharina A1 - Brödner, Doris A1 - Horn, Wolfgang T1 - Correlation of aldehyde emissions and fatty acids content in pine wood and oriented strand boards N2 - Indoor air quality is important for human health and comfort. To ensure good indoor air quality contamination by volatile organic compounds (VOC) should be minimised. The aim of the project is the reduction of unsaturated aldehydes which can emit from oriented Strand boards (OSB): These aldehydes have an impact on the health based evaluation of emissions from products for indoor use according to the AgBB (Ausschuss zur gesundheitlichen Bewertung von Bauprodukten, Committee for Health Evaluation of Building Products) scheine (AgBB 2010). The model OSB were produced in a pilot plant using well known raw materials (Pinus sylvestris at different trunk heights) under using various processing parameters (Wilke et al. 2011). OSB emit predominantly monoterpenes and aldehydes. Aldehydes are oxidation products of fatty acids in wood. The conditions which affect the oxidation process are the fatty acid concentration and composition, the oxygen content, the sample surface and the presence of compounds which indicate, inhibit or stop the oxidation respectively. The oxidation rate rises with an increasing number of double bounds in the fatty acid, e.g. the oxidation rate between oleic, linoleic and linolenic acid correspond to 1:12:24. One of the most important products of fatty acid oxidation is hexanal. It is generated during the oxidation of linoleic acid. This study shows a direct correlation between aldehyde emission and oxidation, hexanal can be used as an indicator for oxidation. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - VOCs KW - Oxidation products KW - Fatty acid KW - Saturated and unsaturated aldehyde KW - Hexanal PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-23878 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Torge, Manfred A1 - Krug, Sonja A1 - Bücker, Michael A1 - Feldmann, Ines A1 - Scharf, Holger A1 - Witthuhn, Heike T1 - Investigation of mercury emissions of historic tin-mercury mirrors N2 - With the implementation of glass casting in France in the second half of the 17th century, larger mirrors could be produced. So-called tin-mercury mirrors were made by coating glass with tin amalgam. Today, many historical mirrors are partly damaged, the image quality is compromised, and the material integrity of the mirror is threatened. The transformation from tin into an oxide starts at the surface of the amalgam and proceeds down to the glass surface. The mercury dissolves as a liquid or gaseous phase. The amalgam layer is destroyed, so that conservation is necessary. Conservators must follow strict safety precautions while handling amalgam mirrors because of possible mercury emissions and corrosion of the amalgam, during which elemental mercury accumulates near the mirror frame in droplets and is emitted into the air. In a research project, the quantity of the mercury emissions from historical mirrors was examined and a technique to decrease these emissions was developed. T2 - ART 2011 -10th International Conference on non-destructive investigations and microanalysis for the diagnostics and conservation of cultural and environmental heritage CY - Florence, Italy DA - 13.04.2011 KW - Zinn-Amalgamspiegel KW - Quecksilber KW - Emission PY - 2011 SP - 1 EP - 8 AN - OPUS4-23879 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, B. A1 - Panaskova, J. A1 - Jann, Oliver A1 - Horn, Wolfgang A1 - Müller, D. A1 - Plehn, W. T1 - Results of sensory tests and sensory-limit settings for building materials in Germany N2 - Indoor air pollutants influence the health and comfort of building occupants and consequently the energy consumption of the building. The pollutants are emitted by various sources. Among these sources, building products are of particular importance. To control the emission of pollutants from building materials, a few different voluntary labelling Systems have been introduced in Europe. In Germany also mandatory “Principles for the health assessment of construction products used in interiors” have been applied for the technical approval of floor coverings since 2004. This procedure is based on the assessment scheine of the Committee for Health-related Evaluation of Building Products (AgBBScheme). The sensory-limit settings for building-material label Blue Angel offer consumer to differ not only low-emission but also low-odour Building materials from another building materials. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - Perceived air-quality KW - Odour evaluation KW - Odour labelling KW - Test procedure KW - Standardisation PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-23882 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Howard-Reed, C. A1 - Liu, Z. A1 - Cox, S. A1 - Little, J. A1 - Horn, Wolfgang A1 - Wilke, Olaf A1 - Wiegner, Katharina A1 - Persily, A. T1 - Inter-laboratory study approach to validate the performance of a prototype reference material for product emissions testing N2 - Product emissions chamber testing involves a complex protocol with several sources of measurement uncertainty (ASTM, 2010; ISO, 2006). Despite the potential for significant variability in measurement results within and among laboratories, there is no Standard method available to assess the accuracy of emissions chamber test results. Recently, Germany’s Federal Institute for Materials Research and Testing (BAM) started a program to evaluate the performance of laboratories testing for the AgBB (German Committee for Health-related Evaluation of Building Products) labelling scheme (Wilke et al., 2009). Test method validation was conducted through interlaboratory studies (ILS) with over 30 participants. Simultaneously, the National Institute of Standards and Technology (NIST) and Virginia Tech (VT) started a program to develop a series of reference materials that mimic real building products, can be tested in typical emissions chambers, and have independently known emission rates (Cox et al., 2010). BAM, NIST and VT subsequently joined forces to conduct a series of inter-laboratory studies using the prototype reference material. A pilot ILS was conducted with BAM and NIST followed by an expanded ILS with several participating countries. Results from these interlaboratory studies have the potential to define an internationally-accepted Standard approach to validate results from product emissions tests. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - Test method validation KW - Volatile organic compounds KW - Product certification PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-23883 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zhang, X.-X. A1 - Würth, Christian A1 - Zhao, L. A1 - Resch-Genger, Ute A1 - Ernsting, N.P. T1 - Femtosecond broadband fluorescence upconversion spectroscopy: improved setup and photometric correction N2 - A setup for fluorescence upconversion spectroscopy (FLUPS) is described which has 80 fs temporal response (fwhm) for emission in the spectral range 425–750 nm. Broadband phase matching is achieved with tilted gate pulses at 1340 nm. Background from harmonics of the gate pulse is removed and sensitivity increased compared to previous designs. Photometric calibration of the upconversion process is performed with a set of fluorescent dyes. For Coumarin 153 in methanol the peak position, bandwidth, and asymmetry depending on delay time are reported. KW - Calibration KW - Fluorescence spectroscopy KW - Fluorescence KW - Upconversion KW - Standard KW - Spectral responsivity KW - Time-resolved fluorescence KW - Quality assurance KW - Coumarin 153 KW - Solvation dynamics PY - 2011 DO - https://doi.org/10.1063/1.3597674 SN - 0034-6748 SN - 1089-7623 VL - 82 SP - 063108-1 EP - 063108-8 PB - American Institute of Physics CY - Melville, NY AN - OPUS4-23886 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute A1 - Mathejczyk, J. A1 - Dullin, C. A1 - Pauli, Jutta A1 - Alves, F. A1 - Napp, J. T1 - Lifetime imaging and lifetime quality analysis in combination with pH-sensitive NIR fluorescence probes to improve tumor detection in vivo T2 - ESME 2011 CY - Leiden, Netherlands DA - 2011-06-01 PY - 2011 AN - OPUS4-23939 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute A1 - Behnke, Thomas A1 - Würth, Christian A1 - Napp, J. A1 - Fischer, L. A1 - Schäferling, M. A1 - Katschinski, D. A1 - Alves, F. A1 - Wottawa, M. T1 - Nanoparticle-based ratiometric approach for oxygen sensing in tumors T2 - ESME CY - Leiden, Netherlands DA - 2011-06-01 PY - 2011 AN - OPUS4-23940 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hennig, Andreas A1 - Hoffmann, Angelika A1 - Borcherding, H. A1 - Schedler, U. A1 - Resch-Genger, Ute T1 - Quantification of surface functional groups by supramolecular host-guest interactions T2 - 2nd International Conference on Cucurbiturils (ICCB) CY - Cambridge, England DA - 2011-06-29 PY - 2011 AN - OPUS4-23941 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kittler, Katrin A1 - Maul, Ronald A1 - Koch, Matthias A1 - Nehls, Irene T1 - Investigation of the systematic availability of the cyanotoxin Cylindrospermopsin in Brassicaceae T2 - Euro Food Chem XVI CY - Gdansk, Poland DA - 2011-07-06 PY - 2011 AN - OPUS4-23942 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Musolff, André A1 - Quercetti, Thomas A1 - Müller, Karsten A1 - Droste, Bernhard A1 - Komann, Steffen T1 - Drop Test Program with a HLW Cask Model - Performance, Measurements and Results T2 - INMM 2011 - 52nd Annual Meeting CY - Palm Desert, CA, USA DA - 2011-07-17 PY - 2011 AN - OPUS4-23945 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spaltmann, Dirk A1 - Löhr, Manuel A1 - Effner, Ute A1 - Scholz, Christian A1 - Manier, Charles-Alix A1 - Woydt, Mathias T1 - Wälzbeständigkeit von diamantartigen Kohlenstoffschichten KW - DLC KW - ZrCN KW - Wälzen KW - Technische Beschichtungen KW - Null-Verschleiß PY - 2011 SN - 1619-5558 VL - 2 IS - 37 SP - 16 EP - 24 PB - Diamond Business KG CY - Bamberg AN - OPUS4-23947 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Döring, Joachim A1 - Bovtun, V. A1 - Brekow, Gerhard A1 - Kreutzbruck, Marc T1 - Charakterisierung der Luftultraschallwandler aus zellulärem ferroelektrischem Polypropylen T2 - DGZfP-Jahrestagung CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23908 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völz, Uwe A1 - Mrasek, Heinz A1 - Heckel, Thomas T1 - Querfehlerprüfung an anisotropen Engspaltschweißnähten mit Gruppenstrahlern T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23909 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Boehm, Rainer A1 - Brackrock, Daniel A1 - Kitze, Jessica A1 - Brekow, Gerhard A1 - Heinrich, W. T1 - Ultraschalluntersuchungen an einem Turbinenradscheibentestkörper mit Sägezahn-Arrays T2 - Jahrestagung der DGZfP 2011 CY - Bremen, Germany DA - 2011-05-29 PY - 2011 AN - OPUS4-23910 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Habel, Wolfgang A1 - Brunner, F.K. T1 - Faseroptische Sensoren für den Einsatz im Monitoring: Ein Überblick N2 - Die herausragenden Eigenschaften faseroptischer Sensoren beim Monitoring geotechnischer Strukturen werden diskutiert und ihre Vor- und Nachteile zusammengefasst. Es werden die Grundlagen der wichtigsten faseroptischen Sensoren (Rückstreu-, Faser-Bragg-Gitter-, Fabry-Perot-Sensoren, Mach-Zehnder-Interferometer sowie Sensoren auf Basis der Niedrig-Kohärenz-Interferometrie) aufbereitet. KW - Monitoring KW - Faseroptische Sensoren KW - Faser-Bragg-Gitter KW - Interferometrische Sensoren KW - Fiber optic sensors KW - Fiber Bragg grating KW - Interferometric sensors PY - 2011 SN - 0002-5968 VL - 6 SP - 204 EP - 211 PB - Wichmann CY - Heidelberg AN - OPUS4-23911 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang A1 - Oppl, R. T1 - European Test Method Validation Approaches T2 - NIST/Virginia Tech Workshop: Reference Material Development for Product Emissions Testing CY - Gaithersburg, MD, USA DA - 2011-04-28 PY - 2011 AN - OPUS4-23913 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nohr, Michael A1 - Wiegner, Katharina A1 - Horn, Wolfgang A1 - Hahn, Oliver T1 - Micro-Camber Thermal Extractors as substitution for conventional emission test chamber for the analysis of VOC T2 - Technart 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-23915 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiegner, Katharina A1 - Hahn, Oliver A1 - Kalus, Sabine A1 - Horn, Wolfgang A1 - Farke, M. T1 - Determination of Formic and Acetic Acids in air or Display cases T2 - Technart 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-23917 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Goedecke, Thomas A1 - Menrad, Andreas A1 - Bethke, John T1 - Application of Nondestructive Testing - Methods for Packaging Examination T2 - 25th IAPRI Symposium on Packaging, international association of packaging research institutes (IAPRI) CY - Berlin, Germany DA - 2011-05-16 PY - 2011 AN - OPUS4-23899 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Droste, Bernhard T1 - Gestaffelte Anforderungen N2 - Klasse 7 - Design, Prüfung und Zulassung von Versandstücken zur Beförderung radioaktiver Stoffe orientieren sich am stofflichen Gefährdungspotenzial und administrativen Kontrollen durch die zuständigen Behörden. KW - Gefahrgutklasse 7 KW - Versandstücke KW - Beförderung radioaktiver Stoffe PY - 2011 SN - 0944-6117 VL - 4 SP - 46 EP - 48 PB - Vogel CY - München AN - OPUS4-23901 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kitze, Jessica A1 - Boehm, Rainer A1 - Montag, Hans-Joachim A1 - Völz, Uwe A1 - Brekow, Gerhard A1 - Kreutzbruck, Marc T1 - SAFT-Rekonstruktion und 3D Lokalisation aus Ultraschallmessungen mit Matrix- und Linear-Arrays in Tauchtechnik T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23902 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rurack, Knut A1 - Wagner, R. A1 - Wan, Wei A1 - Lazrag, I. A1 - Sellergren, B. A1 - Fernandez Sanchez, J. F. A1 - Urraca-Ruiz, J. A1 - Moreno-Bondi, C. A1 - Orellana, G. T1 - Molecularly Imprinted Polymer Films as Sensory Materials for the Selective Detection of Carboxylates via Flourescence T2 - European Polymer Congress 2011(EPF) CY - Granada, Spain DA - 2011-06-26 PY - 2011 AN - OPUS4-23931 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rurack, Knut A1 - Climent Terol, Estela A1 - Martínez-Mánez, Ramon T1 - Implementing Signal Amplification Features with Gated Mesoporous Sensory Hybrids for Methymercury Determination T2 - Hybrid Materials 2011 CY - Strasbourg, France DA - 2011-03-03 PY - 2011 AN - OPUS4-23935 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rurack, Knut A1 - Martínez-Mánez, Ramon T1 - Organically functionalized mesopporous silica particles as a versatile platform for Hg2+ determination, sequestration and CH3Hg+ speciation witz simple analytical protocols T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23936 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wan, Wei A1 - Apel, Jenny A1 - Rurack, Knut A1 - Descalzo, Ana B. T1 - Assessing the FRET Acceptor Potential of Various BODIPY Dyes for Europium as the FRET Donor T2 - International Bunsen Discussion Meeting on Förster Resonance Energy Transfer in Life Sciences CY - Göttingen, Germany DA - 2011-03-27 PY - 2011 AN - OPUS4-23937 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krankenhagen, Rainer A1 - Maierhofer, Christiane A1 - Röllig, Mathias A1 - Kalisch, U. A1 - Meinhardt, J. T1 - Development and application of active thermography to monitor deterioration processes in historic structures T2 - International Symposium on Nondestructive Testing of Materials and Structures CY - Istanbul, Turkey DA - 2011-05-15 PY - 2011 AN - OPUS4-23788 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin A1 - Schoßig, Jörg T1 - Validierung formalkinetischer Größen aus der adiabaten Warmlagerung T2 - Technische Jahreskonferenz der Chemieindustrie CY - Marburg, Germany DA - 2011-05-31 PY - 2011 AN - OPUS4-23789 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krankenhagen, Rainer A1 - Maierhofer, Christiane A1 - Röllig, Mathias T1 - Thermographic investigation of delaminated plaster on concrete T2 - International Symposium on Nondestructive Testing of Materials and Structures CY - Istanbul, Turkey DA - 2011-05-15 PY - 2011 AN - OPUS4-23790 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton T1 - Anlagenspezifische Sicherheitsüberprüfung (RSK-SÜ) deutscher Kernkraftwerke unter Berücksichtigung der Ereignisse in Fukushima-I (Japan) T2 - 56. Sitzung des Fachausschusses Reaktorsicherheit CY - Wiesbaden, Germany DA - 2011-05-24 PY - 2011 AN - OPUS4-23792 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin A1 - Wille, Frank T1 - Rechnerische Simulation des mechanischen Verhaltens von holzgefüllten Stoßdämpfern von Transportbehältern für radioaktive Stoffe T2 - Jahrestagung Kerntechnik, Berliner Congress Center (BBC) CY - Berlin, Germany DA - 2011-05-17 PY - 2011 AN - OPUS4-23793 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kasparek, Eva Maria A1 - Scheidemann, Robert A1 - Wolff, Dietmar A1 - Zencker, Uwe A1 - Völzke, Holger T1 - Untersuchungen zum Verhalten von Dämpferbeton unter Stoßbelastung T2 - Jahrestagung Kerntechnik, Berliner Congress Center CY - Berlin, Germany DA - 2011-05-17 PY - 2011 AN - OPUS4-23794 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Goedecke, Thomas A1 - Wachtendorf, Volker T1 - Combined impact of UV and chemical flufids on HDPE packaging material T2 - 25th IAPRI Symposium on Packaging CY - Berlin, Germany DA - 2011-05-16 PY - 2011 AN - OPUS4-23795 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heyn, Andreas T1 - Zustandsbewertung von Korrosionsschutzsystemen mit elektrochemischen Methoden - Messverfahren, Einsatzgrenzen und Anwendungen T2 - 4. Korrosionsschutz-Symposium - Korrosionssschutz durch Beschichtungen in Theorie und Praxis CY - Trent, Germany DA - 2011-05-25 PY - 2011 AN - OPUS4-23796 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ulrich, Armin A1 - Otremba, Frank T1 - Was halten Tanks überhaupt aus? T2 - Münchner Gefahrguttage CY - Munich, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23797 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Perret, William A1 - Alber, U. A1 - Schwenk, Christopher A1 - Rethmeier, Michael ED - Wieland, H.-J. T1 - Efficient welding simulation of an automotive sheet metal assembly N2 - Fusion welding is widely used in the automotive industry to join metal structures. It is well-known that distortions and residual stresses occur during and after the welding process. Many procedures exist to decrease these negative heat effects of welding, but are often coupled with highly cost intensive experiments. The implementation of a welding Simulation tool to reduce this very expensive experimental procedures is therefore of high interest. Despite the fact that the automotive industry is a key sector for Simulation procedures, welding Simulation Software is nevertheless not yet widely implemented. This is mainly due to the complexity of the Simulation tools requiring expert users and the resulting high time to Solution. In this study, a new fast thermo-mechanical Simulation of a complex and large laser beam welded automotive sheet metal assembly with several non linear welds is simulated. Assumptions and simplifications of the complex physical welding phenomenon, which are made to keep the computational cost and the complexity of the Simulation in an industrial frame, are discussed. The calibration time of the phenomenological heat source model has been optimized with a very fast analytical thermal model and the resulting simulated temperature fields match perfectly with the measured ones. Additionally, the user experience and the time-to-solution are kept within a reasonable time frame for arr industrial environment. All Simulation results are validated with experimental results. T2 - SCT2011 - 3rd International conference on steels in cars and trucks CY - Salzburg, Austria DA - 05.06.2011 KW - Welding simulation KW - Temperature field KW - Laser beam welding KW - Fast calculation PY - 2011 SN - 978-3-514-00783-3 SP - 704 EP - 713 PB - Stahleisen AN - OPUS4-24088 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Ono, K. A1 - Erhard, Anton T1 - Nondestructive testing, 3. Ultrasonics N2 - The field of acoustics deals with sound Propagation in solids, liquids, and gases, whereby the frequencies may lie above or below the Audio band, that is, infrasound (<16 Hz) and ultrasound (>16 kHz), respectively. The speed of sound depends on mechanical properties of the material like elastic constants and compressibility. Interaction of imperfections such as grains, cracks, pores, and inclusions with sound waves results in reflection, refraction, scattering, and attenuation due to discontinuities in elastic moduli and density. By sending a pulse and receiving its reflection, the presence and Location of defects can be determined (pulse-echo technique). Ultrasound was applied in nondestructive testing (NDT) earlier than in medicine, but visualization of the data in a unicolor-scale image was first used in medical ultrasound diagnostics. The principle of ultrasonic testing, for example, the wave types that are suitable for different applications, the frequency ränge employed, reflectivity behavior, mode conversions, probe types, and so on are described in various publications, and a newer ultrasonic method, namely, the phased array technique, is treated in. KW - Ultrasonic waves KW - Piezocomposite materials for ultrasound generation KW - Phased array technique PY - 2011 SN - 978-3-52730-673-2 DO - https://doi.org/10.1002/14356007.o17_o02 SP - 1 EP - 17 PB - Wiley-VCH AN - OPUS4-24090 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Walther, M. A1 - Matterna, M. A1 - Juran, S. A1 - Fähnemann, S. A1 - Stephan, H. A1 - Kraus, Werner A1 - Emmerling, Franziska T1 - Imidazole-containing bispidine ligands: synthesis, structure and Cu(II) complexation N2 - The preparation and characterization of tris-pyridyl bispidine (3,7-diazabicyclo[3.3.1]nonane) derivatives with benzimidazole and imidazole donor groups at the N-3 position of the bispidine Skeleton and their copper(II) complexes are reported. The impact of the hetaryl substituents on the configurational isomerism of piperidones and their corresponding bispidones has been studied by NMR spectroscopy, revealing the exclusive appearance in the enol form for the piperidones in solution and the trans-configuration regarding the two pyridyl substituents, as well as the sole formation of the unsymmetric exo-endo isomers for the corresponding bispidones. Thus, the bispidones are preorganized ligands for building pentacoordinated complexes, confirmed by the preparation and characterization of the corresponding Cu(II) complexes. Of the di-pyridyl piperidones with benzimidazole and imidazole substituents, and of the Cu(II) complex of the benzimidazole-containing bispidone, Crystals have become available for the analysis by X-ray diffraction, showing that the piperidones form the enol tautomers also in the solid state. KW - Piperidone KW - Bispidine KW - Copper(II) KW - Configuration isomerism PY - 2011 SN - 0932-0776 SN - 0340-5087 SN - 0044-3174 VL - 66b SP - 721 EP - 728 PB - Verl. d. Zeitschrift für Naturforschung CY - Tübingen AN - OPUS4-24091 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Woydt, Mathias T1 - Polyalkylene glycols as next generation engine oils N2 - Some of the properties intrinsically present in the backbone of polyalkylene glycols (PAGs), which have nowadays attracted the automotive original equipment manufacturers (OEMs), are presented, such as bio-no-tox properties, heat capacity, extended drains, low friction, low AlSi-liner wear, fuel economy, and very high viscosity indices, and are achieved with metal-, ash-, and polymer-free formulations, which guarantee no adverse contamination of the lambda sensor and the active centers of the catalyzer as well as not to increase the exhaust back pressure of the particulate filter through ash deposits. This paper illuminates the latest results from OEM's engine bench and road testing supporting the following functional benefits: (a) bio-no-tox, (b) improvements of fuel economy, even when compared with latest hydrocarbon-based prototype oils, (c) reduced wear, (d) reduced engine friction, (e) extended drains, (f) suited for bio-fuels, (g) no adverse effects on after-treatment devices through ash-, metal-, and polymer-free formulations, etc. KW - Bio-no-tox KW - Heat capacity KW - Fuel economy KW - Drain KW - Polyglycol KW - Polypropylene glycol KW - Polyalkylene glycol KW - Polybutylene glycol KW - BAM test KW - AlSi-liner wear KW - DLC KW - SRV KW - Slip-rolling KW - Stribeck curve PY - 2011 DO - https://doi.org/10.1520/JAI103368 SN - 1546-962X VL - 8 IS - 6 SP - 1 EP - 15 PB - American Society for Testing and Materials CY - West Conshohocken, Pa. AN - OPUS4-24092 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kluge, Martin A1 - Ferrero, Fabio A1 - Schröder, Volkmar A1 - Acikalin, Hatice Aydan A1 - Steinbach, J. T1 - Modellazione del processo di autoaccensione del TFE KW - Convezione naturale (free convention) KW - Trasporto reattivo (reactive flow) KW - Reazione in fase gas (gas reaction) KW - Autoignizione (self-ignition) PY - 2011 SN - 0390-2358 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. VL - 6 SP - 84 EP - 90 PB - ERIS CY - Milan AN - OPUS4-24094 LA - ita AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Günther, Alexander A1 - Gründer, Klaus-Peter T1 - New bispectral measurement device for fluorescent materials N2 - The application of fluorescent materials improves the visibility for of warning symbols. BAM has used a measurement device to characterize fluorescent materials, which is based on the two-monochromator method. The result of this measurement method is an illuminant independent characteristic of the fluorescent material, called the Donaldson matrix, In view of its age and speed, the measurement device had to be re-designed and re-built. The new measurement facility is explained in greater detail in the paper. First measurement results and a comparison to the older device are also described. T2 - CIE 27th Session CY - Sun City, South Africa DA - 10.07.2011 KW - Fluorescence KW - Fluorescent materials KW - Donaldson factor KW - Total radiance factor KW - Bi-spectral KW - Two-monochromator method PY - 2011 SN - 978-3-901906-99-2 VL - 1 IS - Part 2 SP - 974 EP - 978 AN - OPUS4-24095 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kindrachuk, Vitaliy A1 - Fedelich, Bernard T1 - Stress update algorithm for the combined viscoplastic and plastic behaviours of single-crystal superalloys N2 - A crystallographic constitutive model is developed, which accounts for both rate-sensitive and rate-insensitive flow. Single-crystal plasticity and viscoplasticity are the limiting cases of the model, so that it properly reflects the material response over a wide temperature range. A non-linear dynamic recovery is included to properly describe ratchetting. We provide a robust integration scheme based on generalization of the return-mapping algorithm and of the procedure for active set search. The implicit integration and consistent tangent are implemented through the UMAT subroutine in the ABAQUS finite element program. The capability of the model to account for both high and low strain rates is demonstrated in numerical examples. Finally, the stability of integration scheme and quadratic convergence of the global Newton–Raphson equilibrium iterations are demonstrated on the example of a notched bar under tension. KW - Crystal plasticity KW - Viscoplasticity KW - Implicit integration KW - Superalloy PY - 2011 DO - https://doi.org/10.1002/nme.3172 SN - 0029-5981 SN - 1097-0207 VL - 88 IS - 1 SP - 83 EP - 102 PB - Wiley CY - Chichester AN - OPUS4-24096 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schilder, Constanze A1 - Kohlhoff, Harald A1 - Hofmann, Detlef A1 - Habel, Wolfgang T1 - Bohrpfahlüberwachung mit strukturintegrierten faseroptischen Sensoren N2 - - Zuverlässiger Nachweis der Tragfähigkeit und Strukturintegrität von Bohr- und Rammpfählen - Nur ein Sensor für alle Pfahlprüfmethoden - Umfassendere Aussagen über Boden-Bauwerks-Interaktion und Gebrauchstauglichkeit durch Nutzung von Sensorketten - Langzeitüberwachung tragender Bauwerkselemente T2 - Sensor+Test 2011 CY - Nuremberg, Germany DA - 07.06.2011 PY - 2011 AN - OPUS4-24058 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schilder, Constanze A1 - Kohlhoff, Harald A1 - Hofmann, Detlef A1 - Habel, Wolfgang T1 - Bohrpfahlüberwachung mit strukturintegrierten faseroptischen Sensoren T2 - VDI/VDE-Expertenforum 2011 CY - Nuremberg, Germany DA - 2011-06-07 PY - 2011 AN - OPUS4-24059 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schuler, Stephanie A1 - Habel, Wolfgang A1 - Hillemeier, B. T1 - Messung von Mikroverformungen der Bindemittelmatrix mit eingebetteten faseroptischen Sensoren T2 - Tagung Bauchemie CY - Hamburg, Germany DA - 2011-10-06 PY - 2011 AN - OPUS4-24061 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witt, Jens A1 - Krebber, Katerina A1 - Demuth, J. A1 - Sasek, L. T1 - Fiber optic heart rate sensor for integration into personal protective equipment N2 - The European research project i-Protect “Intelligent PPE system for personnel in high-risk and complex environments”, supported by the EU 7th Framework Programme, develops an advanced personal protective equipment (PPE) system that will ensure active protection and information support for personnel operating in high risk and complex environments in fire fighting, chemical and mining rescue operations. Within the project an intelligent underwear for monitoring the rescuers heart rate, body temperature, and respiratory rate will be developed. T2 - BioPhotonics Workshop CY - Parma, Italy DA - 08.06.2011 PY - 2011 AN - OPUS4-24062 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander A1 - Krywult, L. T1 - Monitoring konstrukcji ziemnych przy zastosowaniu rozlozonych przestrzennie swiatlowodowych sensorow optycznych, zintegrowanych w geosyntetykach. Monitoring of eartwork structures using spatial distributed fibre optic sensors embedded in geosynthetics T2 - 34th Winter School of Rock Mechanics and Geoengineering CY - Kudowa-Zdrój, Poland DA - 2011-03-14 PY - 2011 AN - OPUS4-24063 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander A1 - Glötzl, R. A1 - Glötzl, R. A1 - Krebber, Katerina A1 - Krywult, L. T1 - Optical Distributed Sensing Systems and possible Applications in the Geotechnical Measuring Field T2 - XIV Dams Monitoring International Conference 2011 CY - Walbrzych, Poland DA - 2011-06-13 PY - 2011 AN - OPUS4-24064 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Glötzl, R. A1 - Schneider Glötzl, J. A1 - Wosniok, Aleksander A1 - Krebber, Katerina A1 - Krywult, L. ED - Wintera, J. ED - Kosik, A. ED - Wity, A. T1 - Optical distributed sensing systems and possible applications in geotechnical measuring N2 - In comparison with traditional measuring Systems (pressure cells, piezometers and inclinometers which produce only point measurements) fibre optic sensors are well suited for spatiallydistributed monitoring purposes. The very tiny optical fibres of a diameter of less then 1 mm can operate as sensors in strong electromagnetic fields, under “harsh” explosive and Chemical environments and under ionizing radiation. T2 - XIV Dam monitoring international conference 'safetyof dams - new challenges' ('Bezpieczenstwo zapór - nowe wyzwania') CY - Walbrzych, Poland DA - 13.06.2011 KW - Fibre optic sensor KW - Spatial distributed sensor KW - Polymer optical fibre (POF) KW - Glass optical fibre (GOF) KW - POF OTDR KW - Brillouin sensor KW - BOTDA KW - BOFDA KW - Fibre Bragg grating (FBG) KW - Geosynthetics KW - Geotxtiles KW - Technical textiles PY - 2011 SN - 978-83-61102-53-3 N1 - Serientitel: Monografie - Instytutu Meteorologii i Gospodarki Wodnej – Series title: Monografie - Instytutu Meteorologii i Gospodarki Wodnej IS - Chapter 6 SP - 173 EP - 180 AN - OPUS4-24066 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tentschert, J. A1 - Braun, Ulrike A1 - Heidler, J. A1 - Richter, S. A1 - Kappenstein, O. A1 - Luch, A. A1 - Pfaff, K. T1 - Perfluoro Acrylates as Surface Refining Agents for Paper and Board: Investigations on Their Resistance at Higher Temperature T2 - 3rd International Workshop Anthropogenic Perflourinated Compounds CY - Amsterdam, Netherlands DA - 2011-06-15 PY - 2011 AN - OPUS4-24067 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Basedau, Frank T1 - Langzeitmonitoring der Ederstaumauer T2 - Expertenforum Strukturmonitoring auf der Sensor+Test-Messe CY - Nuremberg, Germany DA - 2011-06-08 PY - 2011 AN - OPUS4-24048 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rohloff, M. A1 - Das, S.K. A1 - Höhm, S. A1 - Grunwald, R. A1 - Rosenfeld, A. A1 - Krüger, Jörg A1 - Bonse, Jörn T1 - Formation of laser-induced periodic surface structures on fused silica upon multiple cross-polarized double-femtosecond-laser-pulse irradiation sequences N2 - The formation of laser-induced periodic surface structures (LIPSS) upon irradiation of fused silica with multiple irradiation sequences consisting of five Ti:sapphire femtosecond (fs) laser pulse pairs (150 fs, 800 nm) is studied experimentally. A Michelson interferometer is used to generate near-equal-energy double-pulse sequences with a temporal pulse delay from -20 to +20 ps between the cross-polarized individual fs-laser pulses (~0.2 ps resolution). The results of multiple double-pulse irradiation sequences are characterized by means of Scanning Electron and Scanning Force Microscopy. Specifically in the sub-ps delay domain striking differences in the surface morphologies can be observed, indicating the importance of the laser-induced free-electron plasma in the conduction band of the solids for the formation of LIPSS. KW - Atomic force microscopy KW - Conduction bands KW - High-speed optical techniques KW - Laser beam effects KW - Scanning electron microscopy KW - Silicon compounds KW - Surface morphology PY - 2011 DO - https://doi.org/10.1063/1.3605513 SN - 0021-8979 SN - 1089-7550 VL - 110 IS - 1 SP - 014910-1 - 014910-4 PB - American Institute of Physics CY - Melville, NY AN - OPUS4-24049 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Schukar, Vivien T1 - Facility for calibration and validation of surface-attached fiber optic sensors to perform reliable strain measurements (invited lecture) T2 - International SAE Spring Meeting CY - Kissimmee, FL, USA DA - 2011-04-11 PY - 2011 AN - OPUS4-24050 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Hüttl, R. A1 - Röben, R. A1 - Kuchejda, M. T1 - Monitoring of corrosion protection in reinforced concrete structures using an integrated pH optode T2 - 5th International Conference on Structural Health Monitoring of Intelligent Infrastructure (SHMII-5) CY - Cancún, Mexico DA - 2011-12-11 PY - 2011 AN - OPUS4-24051 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang T1 - Current European Research and Development Activities in Standardization of Fiber Optic Strain Sensors (invited lecture) T2 - International SAE Spring Meeting, Workgroup AS-3C CY - Kissimmee, FL, USA DA - 2011-04-11 PY - 2011 AN - OPUS4-24052 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang T1 - Standardisierung und Validierung faseroptischer Dehnungssensoren für zuverlässige Messeaussagen (invited lecture) T2 - Versammlung des OpTecBB-Schwerpunkts "PhoKoS" CY - Berlin, Germany DA - 2011-04-20 PY - 2011 AN - OPUS4-24053 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Heidmann, G. T1 - Monitoring von Hochspannungskabel-Muffen und -Endverschlüssen N2 - - Zunehmender Energiebedarf erfordert höhere Übertragungskapazitäten - Dezentrale ökologische Energiegewinnung, z. B. Offshore, erfordert Übertragung großer Energiemengen in die Ballungszentren (Nord-Süd-Trassen) - Hohe Auslastung der Netze erfordert Beherrschbarkeit der im Fehlerfall auftretenden Risiken für Menschen, Umwelt und energietechnische Anlagen - Etwa 90 % der Anlagenausfälle sind verursacht durch Teilentladungen (TE) in Endverschlüssen und Muffen mit modernen polymeren Isoliersystemen - Etablierte elektrische Verfahren erlauben nur externe Schadensdetektion. T2 - Expertenforum Strukturmonitoring auf der Sensor+Test-Messe CY - Nuremberg, Germany DA - 08.06.2011 PY - 2011 AN - OPUS4-24054 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Heidmann, G. T1 - Monitoring von Hochspannungs-Muffen und -Endverschlüssen T2 - Expertenforum Strukturmonitoring auf der Sensor+Test-Messe CY - Nuremberg, Germany DA - 2011-06-08 PY - 2011 AN - OPUS4-24055 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hohendorf, Stefan A1 - Bartholmai, Matthias A1 - Kammermeier, Michael A1 - Pettelkau, Alexander A1 - Farahbakhsh, Mahin A1 - Damm, David A1 - Goedecke, Thomas T1 - Monitoring von Gefahrgutbehältern während des Transports durch autarke Sensorik- und Kommunikationsmodule N2 - Ziel ist die Entwicklung eines universellen Monitoringmoduls für Gefahrgutbehälter, das während der gesamten Nutzungsdauer am Behälter verbleibt. Durch die Auswertung verschiedener Messwerte, die vom Modul erfasst werden, kann die Sicherheit bei Gefahrguttransporten erhöht und das Unfallrisiko verringert werden. Weiterhin können Rückschlüsse über die Sicherheit und den Zustand des Behälters gezogen werden (Alter, Verschleiß, frühere Inhalte, Überschreitung von Spezifikatonsgrenzen). T2 - VDI/VDE-Expertenforum im Rahmen der Messe "Sensor und Test 2011" CY - Nuremberg, Germany DA - 07.06.2011 PY - 2011 AN - OPUS4-24057 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vila-Comamala, J. A1 - Diaz, A. A1 - David, C. A1 - Mantion, Alexandre A1 - Guizar-Sicarios, M. A1 - Guzenko, V. A. A1 - Bunk, O. A1 - Kewish, C. M. T1 - Characterization of a 20 nm Hard X-ray Focus by Ptychographic Coherent Diffractive Imaging T2 - SPIE Smart Structures/ NDE CY - San Diego, CA, USA DA - 2011-03-06 PY - 2011 AN - OPUS4-24079 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vila-Comamala, J. A1 - Mantion, Alexandre A1 - Diaz, A. A1 - Guizar-Sicairos, M. A1 - Karvinen, P. A1 - Bunk, O. A1 - David, C. T1 - Characterization of a 20 nm hard X-ray focus by ptychographic coherent diffractive imaging T2 - JUM@P ´11: Second Joint Users´Meeting@PSI CY - Villigen, Switzerland DA - 2011-09-15 PY - 2011 AN - OPUS4-24080 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - van de Kreeke, Johannes T1 - How does EPTIS develop and why T2 - ILAC PT Consultative Group ILAC Accreditation Issues Committee CY - Montreux, Switzerland DA - 2011-04-13 PY - 2011 AN - OPUS4-24081 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rohrmann, Rolf A1 - Said, Samir A1 - Thöns, Sebastian A1 - Schmid, Wolfgang A1 - Rücker, Werner T1 - Results from monitoring and assessment of offshore wind turbines T2 - Eurodyn 2011, 8th International Conference on Structural Dynamics CY - Leuven, Belgium DA - 2011-07-04 PY - 2011 AN - OPUS4-24082 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rohrmann, Rolf A1 - Rücker, Werner A1 - Said, Samir A1 - Thöns, Sebastian A1 - Schmid, Wolfgang T1 - Monitoring Loads and Operational Demands at Wind Power Plants - Interaction between Tower and Rotor Blades T2 - 3rd Technical Conference WindTurbine Rotor Blades CY - Essen, Germany DA - 2011-06-28 PY - 2011 AN - OPUS4-24083 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tölle, Florian T1 - Residual Stress Reduction by Beam Defocusing in Beam Welding Processes T2 - 13th Conference on Laser Materials Processing in the Nordic Countries CY - Trondheim, Norway DA - 2011-06-27 PY - 2011 AN - OPUS4-24084 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Perret, William A1 - Schwenk, Christopher A1 - Rethmeier, Michael A1 - Alber, U. T1 - Efficient Welding Simulation of an Automotive Sheet Metal Assembly T2 - SCT 2011 CY - Salzburg, Austria DA - 2011-06-05 PY - 2011 AN - OPUS4-24085 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Werrel, Martin A1 - Deubel, Jan A1 - Krüger, Simone A1 - Krause, Ulrich T1 - Calculation of the Heat Release Rate from Oxygen Consumption in the Cone Calorimeter using the Controlled-atmosphere box T2 - 10th International Symposium on Fire Safety Science, University of Maryland CY - College Park, MD, USA DA - 2011-06-19 PY - 2011 AN - OPUS4-24086 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rouquerol, J. A1 - Klobes, Peter A1 - Baron, G. A1 - Denoyel, R. A1 - Giesche, H. A1 - Groen, J. A1 - Levitz, P. A1 - Neimark, A. A1 - Rigby, S. A1 - Skudas, R. A1 - Sing, K. A1 - Thommes, M. A1 - Unger, K. T1 - Methods presently available for the characterisation of macroporous solids: an overview T2 - IX COPS 2011 - 9th International Symposium on the Characterisation of Porous Solids CY - Dresden, Germany DA - 2011-06-05 PY - 2011 AN - OPUS4-24087 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sugiyama, Kaori A1 - Kaburaki, Y. A1 - Iwai, T. A1 - Miyahara, H. A1 - Okino, A. T1 - Direct Injection of Cells into an ICP-MS for metallomic studies by using a droplet injection nebulizer T2 - Third International Symposium on Metallomics CY - Münster, Germany DA - 2011-06-15 PY - 2011 N1 - Geburtsname von Sugiyama, Kaori: Shigeta, K. - Birth name of Sugiyama, Kaori: Shigeta, K. AN - OPUS4-24108 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Larissa A1 - Jakubowski, Norbert A1 - Hösl, Simone A1 - Scheler, Ch. A1 - Roos, P.H. T1 - Development of multiplex immunoassays for protein detection by Laser Ablation (LA-) ICP-MS T2 - Third International Symposium on Metallomics CY - Münster, Germany DA - 2011-06-15 PY - 2011 N1 - Geburtsname von Müller, Larissa: Wäntig, L. - Birth name of Müller, Larissa: Wäntig, L. N1 - Geburtsname von Hösl, Simone: Hardt, S. - Birth name of Hösl, Simone: Hardt, S. AN - OPUS4-24110 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Fischer, Joachim A1 - Lehmann, Jens T1 - Die bauaufsichtliche Zulassung nichtrostender Stähle T2 - GfKORR e.V. AK Eisen und Stahl CY - Iserlohn, Germany DA - 2011-06-09 PY - 2011 AN - OPUS4-24112 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Probst, Ulrich A1 - Wolff, Dietmar A1 - Nagelschmidt, Sven A1 - Schulz, Sebastian T1 - Investigations on the Long Term Behavior of Metal Seals for Spent Fuel Storage Casks T2 - Institute of Nuclear Materials Management 52nd Annual Meeting CY - Palm Desert, CA, USA DA - 2011-07-17 PY - 2011 AN - OPUS4-24113 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mohamed, Alaa A1 - Mix, Renate A1 - Schönhals, Andreas A1 - Friedrich, Jörg F. T1 - Structure of Plasma-Deposited Copolymers Films Synthesized of the Two Chemically Well-Polymerizable Comonomers Acrylic Acid and Styrene T2 - The 20th International Symposium on Plasma Chemistry (2011) CY - Philadelphia, PA, USA DA - 2011-07-24 PY - 2011 AN - OPUS4-24114 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eichler, Thorsten A1 - Isecke, Bernd A1 - Raupach, M. T1 - Time Dependency of Current and Potential Distribution during the Cathodic Protection of RC Structures T2 - EUROCORR 2011 CY - Stockholm, Sweden DA - 2011-09-04 PY - 2011 AN - OPUS4-24115 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Redmer, Bernhard A1 - Kurfiß, M. A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Hochenergie Radiologie mit 600 kV - Was bringen 150 kV mehr? T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24116 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kupsch, Andreas A1 - Lange, Axel A1 - Hentschel, Manfred P. A1 - Manke, I. A1 - Grothausmann, R. T1 - Application of the DIRECTT Algorithm to Sub-Nanometer Electron Tomography T2 - International Symposium on Digital Industrial Radiology and Computed Tomography (DIR 2011) CY - Berlin, Germany DA - 2011-06-20 PY - 2011 AN - OPUS4-24117 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Arlt, Tobias A1 - Grothausmann, R. A1 - Manke, I. A1 - Markötter, H. A1 - Krüger, P. A1 - Haußmann, J. A1 - Hentschel, Manfred P. A1 - Kupsch, Andreas A1 - Lange, Axel T1 - Tomografische Methoden für die Brennstoffzellenforschung T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24118 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Redmer, Bernhard A1 - Ewert, Uwe A1 - Föllner, Maik A1 - Przybilla, Waldemar T1 - High Energy X-Ray Inspection of Welds and Large Components T2 - 1st All-Russia/International Conference on Innovations in NDT (Sib Test) CY - Barnaul, Russia DA - 2011-07-25 PY - 2011 AN - OPUS4-24119 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Redmer, Bernhard A1 - Przybilla, Waldemar A1 - Föllner, Maik A1 - Malitte, Hans-Joachim A1 - Ewert, Uwe T1 - Anwendung hochenergetischer Strahlenquellen in der Durchstrahlungsprüfung T2 - DGZfP Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24120 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lange, Axel A1 - Hentschel, Manfred P. A1 - Kupsch, Andreas A1 - Müller, Bernd R. T1 - Correction of Diffuse X-Ray Detector Based Background T2 - International Symposium on Digital Industrial Radiology and Computed Tomography (DIR 2011) CY - Berlin, Germany DA - 2011-06-20 PY - 2011 AN - OPUS4-24121 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Philipp, Rosemarie A1 - Cabillic, J. A1 - Schiel, D. A1 - Ernteborg, H. A1 - Goenaga-Infante, H. A1 - LAlere, B. T1 - Joint Research Project ENV08 "Traceable Measurements for Monitoring Critical Pollutants under the European Water Framework Directive (WFD) 2000/60/EC" T2 - 15th International Congress of Metrology CY - Paris, France DA - 2011-10-03 PY - 2011 AN - OPUS4-24123 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stegemann, B. A1 - Bonse, Jörn A1 - Richter, M. A1 - Schultz, C. A1 - Pahl, H.-U. A1 - Rau, B. A1 - Quaschning, V. A1 - Fink, F. T1 - Laser Ablation of Thin Films for Photovoltaic Application T2 - 26. Tag der Chemie CY - Berlin, Germany DA - 2011-07-13 PY - 2011 AN - OPUS4-24124 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bachmann, Marcel A1 - Avilov, Vjaceslav A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - CFD Simulation of the Liquid Metal Flow in High Power Laser Welding of Aluminum with Electromagnetic Weld Pool Support T2 - Proceedings 2nd International Conference on Fluid Mechanics and Heat & Mass Transfer 2011 CY - Corfu, Greece DA - 2011-07-14 PY - 2011 AN - OPUS4-24125 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. T1 - Interpretations of temperature measurements in organic peroxide pool fires T2 - 5th European Combustion Meeting ECM 2011, Cardiff University CY - Cardiff, Wales DA - 2011-06-29 PY - 2011 AN - OPUS4-24099 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schälike, Stefan A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. T1 - CFD Simulation to predict the thermal radiation of large LNG pool fires T2 - 5th European Combustion Meeting ECM 2011, Cardiff University CY - Cardiff, Wales DA - 2011-06-29 PY - 2011 AN - OPUS4-24100 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter T1 - An efficient and clean fuel for high temperature process industries T2 - 11th International Conference on Energy for a Clean Environment CY - Lisbon, Portugal DA - 2011-07-05 PY - 2011 AN - OPUS4-24101 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheid, Marc T1 - Sicherheitstechnische Kenngrößen von Stäuben: Bestimmungsmethoden - Nutzen für die Praxis T2 - Seminar des Hauses der Technik "Aktueller Staubexplosionsschutz" CY - Essen, Germany DA - 2011-06-28 PY - 2011 AN - OPUS4-24102 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppen, Robert A1 - Klein-Hartwig, Karin A1 - Koch, Matthias T1 - New CRM for T-2 and HT-2 toxin: a crucial tool for quality assurance and control in food analysis T2 - 5th International Symposium on Recent Advances in Food Analysis (RAFA 2011) CY - Prague, Czech Republic DA - 2011-11-01 PY - 2011 AN - OPUS4-24104 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Regina A1 - Maierhofer, Christiane A1 - Kreutzbruck, Marc T1 - Numerische Verfahren für die aktive Thermografie zur Untersuchung der Rückwand T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24105 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hösl, Simone A1 - Scheler, Ch. A1 - Jakubowski, Norbert A1 - Müller, Larissa A1 - Linscheid, M. T1 - Quantitative detection of antibodies via metal coded tagging of the hinge region T2 - Tag der Chemie, Humboldt-Universität zu Berlin CY - Berlin, Germany DA - 2011-07-13 PY - 2011 N1 - Geburtsname von Hösl, Simone: Hardt, S. - Birth name of Hösl, Simone: Hardt, S. N1 - Geburtsname von Müller, Larissa: Wäntig, L. - Birth name of Müller, Larissa: Wäntig, L. AN - OPUS4-24107 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kadenkin, Alexander A1 - Linnow, K. A1 - Steiger, M. T1 - Determination of salt pollutants in building materials using Raman spectroscopy T2 - TECHNART 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-24128 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Wrought iron arch bridge: Measurement and Materials Testing T2 - 12th ICMS, International Conference for Metal Structures, Wroclaw University of Technology CY - Wroclaw, Poland DA - 2011-06-15 PY - 2011 AN - OPUS4-24129 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - NDT-CE and Non-destructive defect detection during CFRP-strengthened concrete beam tests T2 - Non-destructive testing in civil engineering seminar, Technical University Parma CY - Parma, Italy DA - 2011-02-27 PY - 2011 AN - OPUS4-24130 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Introduction to NDT/NDE: Non-Destructive Testing and Evaluation T2 - SmartEN Multi-Disciplinary Workshop, AIT Summerschool 2011 CY - Athens, Greece DA - 2011-07-06 PY - 2011 AN - OPUS4-24131 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan A1 - Lippitz, Andreas A1 - Kraft, Benedikt A1 - Rackwitz, Vanessa A1 - Terborg, R. T1 - Performance Check of EDS X-Ray Spectrometers - Extension to high Count Rates T2 - Microscopy & Microanalysis 2011 Meeting CY - Nashville, TN, USA DA - 2011-08-07 PY - 2011 AN - OPUS4-24132 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mix, Renate A1 - Yin, Huajie A1 - Friedrich, Jörg F. T1 - Special interface design for adhesion improvement T2 - ICCE-19, 19th Annual International Conference on Composites or Nano Engineering CY - Shanghai, China DA - 2011-07-24 PY - 2011 AN - OPUS4-24134 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Salge, T. A1 - Hodoroaba, Vasile-Dan A1 - Tunckan, O. A1 - Terborg, R. A1 - Turan, S. T1 - Advanced light element and low energy X-ray analysis of ceramics and ceramic-metal joints using SEM/EDX with Silicon Drift Detectors (SDD) T2 - 20th National Electron Microscopy Congress CY - Kemer, Turkey DA - 2011-10-25 PY - 2011 AN - OPUS4-24135 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan A1 - Marinenko, R. A1 - Small, J. A1 - Unger, Wolfgang T1 - EPMA on Copper-Gold Alloys - A CCQM/SAWG Pilot Study T2 - Microscopy and Microanalysis 2011 Meeting CY - Nashville, TN, USA DA - 2011-08-07 PY - 2011 AN - OPUS4-24136 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - The dynamic force transfer of slab tracks and floating slab tracks and the corresponding ground vibration. T2 - EURODYN 2011, 8th International Conference on Structural Dynamics CY - Leuven, Belgium DA - 2011-07-04 PY - 2011 AN - OPUS4-24137 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Staude, Andreas A1 - Bartscher, M. A1 - Ehrig, Karsten A1 - Goebbels, Jürgen A1 - Koch, M. A1 - Neuschaefer-Rube, U. A1 - Nötel, Jörg T1 - Quantification of the capability of micro-CT to detect defects in castings using a new test piece and a voxel-based comparison method N2 - We present a modified aluminium casting which is especially suited as test piece for measuring casting defects and the geometry by means of cone-beam micro-focus X-ray systems, and which may become a reference standard for dimensional measurements and defect detection. To obtain a test piece with inner geometries measured by tactile means, we divided a small aluminium cylinder head into four pieces in such a way that most inner surfaces can be reached with a tactile probe. Reference geometries (spheres and cylinders) were applied to define a coordinate system for aligning the measurements in the disassembled and re-assembled state. The four pieces were re-assembled after the tactile measurement. The test piece also contains casting defects. In order to be able to use the assembled cylinder head as reference sample for defect detection, measurements with higher spatial resolution and better signal-to-noise ratio were performed on the single parts. For improving the reliability of the reference measurements, CT measurements of each part were carried out in three different orientations, and the individual defect detections were combined to obtain a reference data set with a high probability of defect detection and a low rate of erroneous detections. A new method for comparing the defect detection in a CT measurement to a reference data set is demonstrated, which provides individual information on every detected flaw. We discuss the results of measurements in the assembled state with respect to the reference data for flaw detection. KW - X-ray tomography KW - Casting KW - Defects KW - Porosity PY - 2011 DO - https://doi.org/10.1016/j.ndteint.2011.05.006 SN - 0963-8695 VL - 44 IS - 6 SP - 531 EP - 536 PB - Butterworth-Heinemann CY - Oxford AN - OPUS4-24028 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Oliver A1 - Christoph, Gabriele A1 - Kalbe, Ute A1 - Berger, Wolfgang T1 - Comparison of stir bar sorptive extraction (SBSE) and liquid-liquid extraction (LLE) for the analysis of polycyclic aromatic hydrocarbons (PAH) in complex aqueous matrices N2 - Stir bar sorptive extraction (SBSE) is an equilibrium extraction method used amongst others for the analysis of polycyclic aromatic hydrocarbons (PAH) in aqueous samples. We compared SBSE to liquid–liquid extraction (LLE) for aqueous eluates obtained from batch and column tests of PAH contaminated soils to check whether SBSE might be considered as an alternative sample preparation method. We used soils with different particle size distribution, organic matter content, and resulting eluate turbidity to test the sample preparation methods on eluates with matrices of varying complexity. Furthermore, we studied the influence of diluted organic matter (DOM) on the PAH sorption process to the polymer coating of the stir bar during SBSE. In the majority of cases, we found higher PAH concentrations (up to 288%) with SBSE than with LLE. The turbidity correlates with the difference in PAH results, i.e. the greater the turbidity in the eluate, the more PAH we found with SBSE compared to LLE. We observed no similar trend regarding the amount of total organic carbon (TOC). The presence of DOM in the eluate seems to hamper the SBSE slightly, the PAH recovery varied between 82 and 104%. KW - Stir bar sorptive extraction KW - Liquid-liquid extraction KW - Leaching KW - Batch test KW - Column test KW - Complex aqueous matrix PY - 2011 DO - https://doi.org/10.1016/j.talanta.2011.06.035 SN - 0039-9140 VL - 85 IS - 3 SP - 1428 EP - 1434 PB - Elsevier CY - Amsterdam AN - OPUS4-24031 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kittler, Katrin A1 - Maul, Ronald A1 - Koch, Matthias A1 - Nehls, Irene T1 - Systematic availability of the cyanotoxin Cylindrospermopsin in Sinapis alba T2 - Tag der Chemie 2011 CY - Berlin, Germany DA - 2011-07-13 PY - 2011 AN - OPUS4-24032 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Merkel, Stefan A1 - Köppen, Robert A1 - Koch, Matthias A1 - Nehls, Irene T1 - Analysis of Ergot Alkaloids without Epimerization T2 - Tag der Chemie 2011 CY - Berlin, Germany DA - 2011-07-13 PY - 2011 AN - OPUS4-24033 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hennig, Andreas A1 - Hoffmann, Angelika A1 - Borcherding, H. A1 - Thiele, T. A1 - Schedler, U. A1 - Resch-Genger, Ute T1 - Quantification of surface functional groups on polymer microspheres by supramolecular host-guest interactions N2 - We introduce a method to determine the number of accessible functional groups on a polymer microsphere surface based on the interaction between the macrocyclic host cucurbit[7]uril (CB7) and a guest reacted to the microsphere surface. After centrifugation, CB7 in the supernatant is quantified by addition of a fluorescent dye. The difference between added and detected CB7 affords the number of accessible surface functional groups. KW - Cucurbituril KW - Acridine orange KW - Fluorescence KW - Polymer surface KW - Surface modification KW - Quantification PY - 2011 DO - https://doi.org/10.1039/c1cc11692d SN - 0022-4936 SN - 0009-241x SN - 1359-7345 SN - 1364-548x VL - 47 IS - 27 SP - 7842 EP - 7844 PB - Royal Society of Chemistry CY - Cambridge AN - OPUS4-24034 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Bremser, Wolfram ED - Kromidas, S. T1 - Ermittlung und Angabe der Messunsicherheit N2 - Seit Erscheinen des „Guide to the Expression of Uncertainty in Measurement (GUM)“ [184] im Jahre 1993 (in redaktionell bearbeiteter Fassung 1995) ist das Konzept der Messunsicherheit in den unterschiedlichsten Bereichen des Mess und Prüfwesens angenommen und umgesetzt worden. Inzwischen gibt es ausführliche Leitfäden auch für wichtige Bereiche der analytischen Chemie (wie Umwelt- oder Lebensmittelanalytik), die auf die spezifischen Belange dieser Bereiche detailliert eingehen. Viele der im Anfangsstadium der Umsetzung des Konzeptes offenen Fragen wurden inzwischen gelöst, insbesondere sind eine Vielzahl von Anwendungsfällen bearbeitet und dokumentiert worden. Die vorangegangene Ausgabe dieses Buches enthielt einen Beitrag zum Schätzen der Messunsicherheit [224], in dem bereits die grundlegenden Aspekte und die Herangehensweise erörtert wurden. Obwohl der nachstehende Beitrag komplett aktualisiert und neu gestaltet wurde, um die Tendenzen der Entwicklung in den vergangenen zehn Jahren widerzuspiegeln, wird der Leser damals betrachtete Aspekte bestätigt sehen und einige der Grundgedanken wiederfinden. Die in diesem Kapitel verwendeten Begriffe und Definitionen in der Validierung, wie Präzision, Wiederholbarkeit, Reproduzierbarkeit, Richtigkeit oder Rückführbarkeit sowie die zugehörigen statistischen Konzepte werden in den Kapitel 3-11 dieses Buches ausführlich betrachtet, weshalb auf eine nochmalige Definition und Erläuterungen verzichtet wird. Der an weiterführenden Darstellungen interessierte Leser wird auf das Kompendium [185] verwiesen. Der in diesem Kapitel verwendete Begriff des Messverfahrens bezieht sich auf die Gesamtheit aller Prozeduren, die zur Erlangung eines Messwertes und einer dazugehörigen Unsicherheit für die vom zu untersuchenden Objekt gefragte Messgröße erforderlich sind. Dazu gehören die Probenahme, die mechanische und chemische Probenvorbereitung, z. B. mit den Schritten Trocknung, Mahlung, Siebung, Mischung (mechanisch) oder Extraktion (chemisch), alle Zwischenschritte wie z. B. zur Abtrennung die Messung behindernder (interferierender) Probenkomponenten („clean-up“), eine evtl. Transformation der Zielkomponente(n), wie z. B. eine Derivatisierung, der eigentliche instrumentelle Nachweis und die Bestimmung der in Rede stehenden Messgröße, die Kalibrierung des Nachweisinstruments inld. aller Schritte zur Erzeugung der Referenzpunkte (Kalibrierstandards) sowie die abschließende Datenauswertung zur Erzeugung des Messwertes und der dazugehörigen Unsicherheit. Nicht jedes Verfahren wird alle diese Teilschritte einschließen oder benötigt sie, so dass sich die Ermittlung der Messunsicherheit eines Verfahrens in einem Labor immer nur auf alle von dem jeweiligen analytischen Labor bearbeiteten Prozeduren (Teilmengen der obigen Auswahl) beziehen kann und wird. Der Begriff Messmethode hingegen bezieht sich (anders als in der angelsächsischen Literatur) i. d. R. allein auf das eigentliche (instrumenteile) Separationsund/oder Detektionsverfahren (wie ToF-IDMS, GC-FID, LC-MS/MS, HPLC-DAD, FT-IRu. a.). KW - Messunsicherheit KW - Messmodell KW - Quantifizierung KW - Methoden der Analytik PY - 2011 SN - 978-3-527-32938-0 SP - 579 EP - 614 PB - Wiley-VCH Verlag GmbH & Co. KGaA ET - 2. Auflage AN - OPUS4-24036 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hübert, Thomas A1 - Boon-Brett, L. A1 - Black, G. A1 - Banach, Ulrich T1 - Hydrogen sensors - A review N2 - Hydrogen sensors are of increasing importance in connection with the development and expanded use of hydrogen gas as an energy carrier and as a chemical reactant. There are an immense number of sensors reported in the literature for hydrogen detection and in this work these sensors are classified into eight different operating principles. Characteristic performance parameters of these sensor types, such as measuring range, sensitivity, selectivity and response time are reviewed and the latest technology developments are reported. Testing and validation of sensor performance are described in relation to standardisation and use in potentially explosive atmospheres so as to identify the requirements on hydrogen sensors for practical applications. KW - Hydrogen sensors KW - Hydrogen detection KW - Detection technologies KW - Technology developments PY - 2011 DO - https://doi.org/10.1016/j.snb.2011.04.070 SN - 0925-4005 SN - 1873-3077 VL - 157 IS - 2 SP - 329 EP - 352 PB - Elsevier CY - Amsterdam [u.a.] AN - OPUS4-24037 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Keßler, S. A1 - Gehlen, C. A1 - Ebell, Gino A1 - Burkert, Andreas T1 - Die Aussagegenauigkeit der Potentialfeldmessung N2 - Die Potentialfeldmessung ist ein Standardverfahren zur Zustandserfassung von Stahlbetonbauwerken. Sie dient der zerstörungsfreien Detektion von aktiv korrodierenden Bereichen. Die Aussagegenauigkeit der Potentialfeldmessung ist von großer wirtschaftlicher Bedeutung, da deren Messergebnisse eine wichtige Entscheidungsgrundlage für die Erarbeitung von Instandsetzungsmaßnahmen bilden. Zur Ermittlung der Aussagegenauigkeit der Potentialfeldmessung wird ein numerisches Verfahren vorgestellt. Die wichtigsten Einflussgrößen auf die Potentialfeldmessung wie Anodengröße, Elektrolytwiderstand und Messraster wurden im Hinblick auf die Aussagegenauigkeit ausgewertet. KW - Bauwerksüberwachung KW - Defekt KW - Detektion KW - Korrosion KW - Lebensdauer KW - Numerische Verfahren KW - Stromdichte-Potential-Kurven KW - Zerstörungsfrei KW - Zerstörungsfreies Messverfahren KW - Bauwerkserhaltung/Sanierung KW - Bewehrung KW - Potentialfeldmessung KW - Betonstahl KW - Elektrolytwiderstand PY - 2011 DO - https://doi.org/10.1002/best.201100025 SN - 0005-9900 SN - 1437-1006 VL - 106 IS - 7 SP - 481 EP - 489 PB - Ernst CY - Berlin AN - OPUS4-23988 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Maierhofer, Christiane A1 - Krankenhagen, Rainer A1 - Röllig, Mathias T1 - Aktive Thermografie zur zerstörungsfreien Prüfung von historischem Mauerwerk N2 - Mit aktiver Thermografie können in Mauerwerksstrukturen sowohl die Oberflächeneigenschaften als auch Inhomogenitäten bis in eine Tiefe von mehreren Zentimetern zerstörungsfrei untersucht werden. Neben der Charakterisierung struktureller Eigenschaften wie Risse, Ablösungen und Aufbau des Mauerwerks sind auch Aussagen zu den thermischen Materialeigenschaften und der Feuchte möglich. In diesem Beitrag werden das Prinzip des Messverfahrens, Laboruntersuchungen und eine Fallstudie vorgestellt. KW - Aktive Thermografie KW - Historisches Mauerwerk KW - Feuchte KW - Thermische Diffusivität KW - Anregungsquellen PY - 2011 SN - 978-3-86780-216-1 VL - 10 SP - 179 EP - 185 AN - OPUS4-23989 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yin, Huajie A1 - Mix, Renate A1 - Friedrich, Jörg Florian T1 - Influence of differently structured aluminium-polypropylene interfaces on adhesion N2 - Polar groups were introduced on polypropylene surfaces for increasing the surface energy and the peel strength to evaporated aluminium layers. Three kinds of plasma processes were used for introducing such functional groups to polyolefin surfaces: low-pressure radio-frequency (RF) O2 plasma exposure, atmospheric-pressure dielectric-barrier discharge (DBD) treatment in air, and the deposition of allylamine plasma polymer. The amino groups of the allylamine plasma polymer were also used as anchoring points for chemical introduction of covalently bonded spacer molecules equipped with reactive endgroups. Thus, silanol endgroups of a covalently bonded spacer were able to interact with the evaporated metal layer. The Al-PP composites achieved a maximal peel strength of 470 N/m by exposing the polymer to the lowpressure O2 plasma and 500 N/m on exposure to the atmospheric DBD plasma. After allylamine plasma polymerization and grafting of spacers, the peel strength was usually higher than 1500 N/m and the composites could not be peeled. KW - Polypropylene KW - Low-pressure RF oxygen plasma KW - Dielectric barrier discharge (DBD) KW - Pulsed plasma polymerization KW - Surface wettability KW - Peel strength PY - 2011 DO - https://doi.org/10.1163/016942410X511132 SN - 0169-4243 SN - 1568-5616 VL - 25 IS - 8 SP - 799 EP - 818 PB - VNU Science Press CY - Utrecht AN - OPUS4-23990 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lohrer, Christian A1 - Eckhardt, Dietrich A1 - Blum, J. T1 - Normenreihe DIN EN 15947 über Feuerwerkskörper N2 - Der vorliegende Bericht gibt einen Überblick über die neue Normenreihe DIN EN 15947 über „Pyrotechnische Gegenstände - Feuerwerkskörper, Kategorien 1, 2 und 3". Es werden der Anwendungsbereich aufgezeigt und wesentliche Änderungen im Vergleich zu der zurückgezogenen und ersetzten Normenreihe DIN EN 14035 über „Feuerwerkskörper" vorgestellt. Die Normenreihe DIN EN 15947 besteht aus den fünf Teilen „Begriffe", „Kategorien und Feuerwerkstypen", „Mindestanforderungen an die Kennzeichnung", „Prüfverfahren" und „Anforderungen an Konstruktion und Funktion" und wurde im Dezember 2010 veröffentlicht. KW - Pyrotechnische Gegenstände KW - Kategorien KW - Prüfverfahren KW - DIN EN 14035 PY - 2011 SN - 0722-2912 SN - 0011-4952 VL - 7 SP - 21 EP - 26 PB - Beuth CY - Berlin AN - OPUS4-23992 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Girard-Lauriault, Pierre-Luc A1 - Ruiz, J.-C. A1 - Gross, Thomas A1 - Wertheimer, M. R. A1 - Unger, Wolfgang T1 - Ultra-shallow chemical characterization of organic thin films deposited by plasma and vacuum-ultraviolet, using angle- and excitation energy-resolved XPS N2 - Nitrogen (N)-rich organic thin films were deposited using both low-pressure plasma- and vacuum-ultraviolet-based techniques, from mixtures of ammonia (NH3) and ethylene (C2H4). These films were investigated using angle-resolved and excitation energy resolved X-ray photoelectron spectroscopy (ARXPS and ERXPS, respectively) in order to determine their sub-surface chemical profiles. These two techniques enable one to tune the “XPS 95%” information depth, z 95%, by varying either the angle or the excitation energy. Using a combination of both techniques, z 95% can be varied continuously from 0.7 to 11 nm. The surface-near chemistry is investigated using both high-resolution C 1s spectra and elemental concentrations derived from elemental peak intensities. Results show that while laboratory XPS, and even ARXPS, suggest homogenous surface chemistries, the novel combination of ARXPS and ERXPS points to the existence of a compositional profile in the extreme outer surface layer. Our conclusions are supported by simulations using SESSA software. KW - Plasma polymers KW - Vacuum ultraviolet photopolymers KW - Synchrotron XPS KW - Depth profile PY - 2011 DO - https://doi.org/10.1007/s11090-011-9306-3 SN - 0272-4324 VL - 31 IS - 4 SP - 535 EP - 550 PB - Plenum Publ. Corp. CY - New York, NY, USA AN - OPUS4-23993 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thöns, Sebastian A1 - Rücker, Werner T1 - Überwachung von Brückenbauwerken in Deutschland T2 - Seminar zu ausgewählten Problemstellungen beim Entwerfen, dem Bau und der Überwachung, aktueller Brückenbauprojekte. CY - Gdansk, Poland DA - 2011-06-14 PY - 2011 AN - OPUS4-23995 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rohrmann, Rolf A1 - Rücker, Werner A1 - Said, Samir A1 - Schmid, Wolfgang A1 - Thöns, Sebastian T1 - Monitoring komplexer Anlagen am Beispiel von Offshore-Windenergieanlagen T2 - VDI/VDE Expertenforum 2011, Strukturmonitoring und Zustandsüberwachung CY - Nuremberg, Germany DA - 2011-06-07 PY - 2011 AN - OPUS4-23996 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von der Ehe, Kerstin A1 - Wolff, Dietmar A1 - Jaunich, Matthias A1 - Böhning, Martin A1 - Goering, Harald T1 - UHMW-PE Study of structural differences induced by exposure to gamma radiation T2 - 25th Symposium on Effects of Radiation on Nuclear Materials CY - Anaheim, CA, USA DA - 2011-06-15 PY - 2011 AN - OPUS4-23980 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mohamed, Alaa A1 - Mix, Renate A1 - Schönhals, Andreas A1 - Friedrich, Jörg F. T1 - Surface and Bulk Properties of Spin Coated Commercial and Thin Plasma-Polymerized Polystyrene Films T2 - The 18th International Colloquium on Plasma Processes (CIP) 2011 CY - Nantes, France DA - 2011-07-04 PY - 2011 AN - OPUS4-23982 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chen, Ji A1 - Schwenk, Christopher A1 - Wu, Chuan Song A1 - Rethmeier, Michael T1 - Prediction of weld pool shape and influence of joint preparation angle for new gas metal arc welding processes N2 - This article studies the three dimensional transient weld pool dynamics and the influence of joint preparation angle on welding of low carbon structural steel plates using the ForceArc® process. ForceArc is a new gas metal arc welding technology which allows adequate fusion and penetration with a smaller V groove angle. This enhances welding efficiency significantly because of reduction of layers and low material consumption. The deformation of the weld bead is calculated with an accurate coupling of the heat transfer with fluid flow through continuity, momentum and the energy equations combined with the effect of droplet impingement, gravity, electromagnetic force, buoyancy, drag forces and surface tension force (Marangoni effect). Four different angles of V groove are employed with the same welding parameters and their influence on the weld pool behavior and weld bead geometry is calculated and analyzed, to allow subsequent calculations of residual stress and distortion of the workpiece. Such a simulation is an effective way to study welding processes because the influence of all the welding parameters can be analyzed separately with respect to thermal cycle, weld bead formation, and the microstructure of the weld. Good agreement is shown between the predicted and experimentally determined weld bead dimensions. It was found that with a larger groove angle, the penetration depth increases. Furthermore, a higher wire feeding rate is needed to fill the larger groove. The model presented can be used for further analyses of GMAW processes as well as input data for the numerical calculation of welding induced residual stresses and distortions using Computational Weld Mechanics CWM. T2 - JOM-16 - 16th International Conference on the Joining of Materials CY - Tisvildeleje, Denmark DA - 10.05.2011 KW - Numerical simulation KW - Gas metal arc welding KW - Weld pool shape KW - Fluid flow KW - V groove PY - 2011 SN - 87-89582-19-5 IS - JOM 7 / J15 SP - 1 EP - 13 AN - OPUS4-23984 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Properties of repair mortars - potentials and risks of a tailor-made mixture proportioning N2 - Despite the numerous possibilities to influence the properties of repair mortars by modifications of the mixture proportioning, it is almost impossible to change an individual property without influencing other mortar properties. When optimising a mixture, it has to be decided for each individual case, which of the mortar properties needs to be treated with the highest priority. Most properties can be altered by several different measures, which may vary in effectiveness, side effects and cost efficiency. As the prevention of shrinkage induced constraining cracks is crucial for the durability and Service life of a concrete repair task, in the presented paper special attention is paid to the influences on the mortar’s shrinkage behaviour. On the basis of parameter studies it is shown, how it may be beneficial in certain cases to accept the worsening of some general properties if by this measure another property, which is essential for the individual application task, can be enhanced significantly. In general a tailor-made approach for the mixture proportioning seems beneficial but due to the complexity of the constituents’ interactions in repair mortars, it bears a high risk of unexpected malfunctions. T2 - Concrete-Workshop 'Performance-based specifications for concrete' CY - Leipzig, Germany DA - 14.06.2011 KW - Repair mortar KW - Concrete rehabilitation KW - Repair systems KW - Polymer cement mortar (PCC) KW - Sprayed polymer cement mortar (SPCC) PY - 2011 SN - 978-3-9814523-0-3 SP - 319 EP - 329 AN - OPUS4-23985 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nöll, G. A1 - Daub, J. A1 - Lutz, M. A1 - Rurack, Knut T1 - Synthesis, spectroscopic properties, and electropolymerization of azulene dyads N2 - Four azulene dyads have been synthesized and studied by spectroscopic and electrochemical methods. A triarylamine, a boron-dipyrromethene (BDP or BODIPY), a porphyrin, and an isoalloxazine moiety have been linked to an extended π electron system at the 2-position of azulene, leading to the dyads 1–4, respectively. For the synthesis of 1–4, first 2-(4-ethynyl-phenyl)azulene (EPA) was prepared, which was further reacted with the halogenated chromophores by Pd-catalyzed cross-coupling reactions. The dyads 1–4 exhibit strong absorption bands in the visible range, which are dominated by the absorption spectra of the individual subchromophores. Fluorometric studies of 2–4 revealed that after excitation of the subchromophoric unit attached to the parent azulene moiety, quenching mainly through energy transfer to azulene is effective, whereas possible charge-transfer interactions play only a minor role. Potentiodynamic oxidation of the dyads 1–4 leads to the formation of polymer films, which are deposited at the electrode. The polymer film derived from 1 was further characterized by spectroelectrochemistry. During positive doping of poly-1, a strong absorption band appears at 13,200 cm–1, which is typical for triarylamine radical cations. This band is overlapping with a broad absorption band in the low-energy region that might be caused by charge-transfer interactions within the polymer. KW - Azulen KW - Elektropolymerisation KW - Energietransfer KW - Farbstoffe KW - Fluoreszenz PY - 2011 DO - https://doi.org/10.1021/jo200080v SN - 0022-3263 SN - 1520-6904 VL - 76 IS - 12 SP - 4859 EP - 4873 PB - American Chemical Society CY - Washington, DC AN - OPUS4-23987 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Recknagel, Christoph T1 - Performance assessment of construction sealants by complex testing - First steps of a complementary approach T2 - Fourth International Symposium on durability of building and construction sealants and adhesives CY - Anaheim, CA, USA DA - 2011-06-14 PY - 2011 AN - OPUS4-23952 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Deubel, Jan A1 - Fettig, Ina A1 - Werrel, Martin A1 - Krüger, Simone A1 - Piechotta, Christian T1 - Investigation on the Detectability of Fire Accelerants after different Fire Scenarios in the Cone Calorimeter T2 - 10 th International Symposium on Fire Safety Science, University of Maryland CY - College Park, MD, USA DA - 2011-06-19 PY - 2011 AN - OPUS4-23955 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger T1 - Transport- und Lagerbehälter Aktuelle Entwicklungen in der sicherheitstechnischen Nachweisführung T2 - Neue Entwicklungen im Strahlenschutz und ihre Anwendung in der Praxis (TÜV SÜD Industrie Service GmbH / TÜV SÜD Akademie GmbH) CY - Munich, Germany DA - 2011-06-30 PY - 2011 AN - OPUS4-23956 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin A1 - Matyschik, Jan T1 - Optimierung von Abbruch und Bauschuttaufbereitung zur Rückgewinnung hochwertiger Baustoffe T2 - Arbeitstreffen Ressourceneffizienz im Bauwesen, organisiert vom BMU CY - Berlin, Germany DA - 2011-05-04 PY - 2011 AN - OPUS4-24009 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabe, Torsten T1 - Keramische Folien- und Multilayertechnologie T2 - eingeladener Vortrag zum II. Innovationsworkshop: Energiespeicherung u. deren zukünftige Applikationen CY - Halle (Saale), Germany DA - 2011-05-23 PY - 2011 AN - OPUS4-24010 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nofz, Marianne A1 - Müller, Ralf A1 - Reinsch, Stefan A1 - Jäger, Christian A1 - Deubener, J. T1 - Eigenschaftsanomalien für CaO-Al2O3-B203-SiO2-Gläser mit variiertem Al2O3-Gehalt T2 - 85. Glastechnische Tagung CY - Saarbrücken, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24011 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ried, Peter A1 - Gaber, Martin A1 - Müller, Ralf A1 - Holtappels, Kai A1 - Schmidtchen, Ulrich A1 - Deubener, J. T1 - Wasserstoffpermeations-messung an Gläsern T2 - Glastechn. Tagung, HVG-DGG CY - Saarbrücken, Germany DA - 30.05.2011 PY - 2011 AN - OPUS4-24012 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zencker, Uwe A1 - Weber, Mike A1 - Wille, Frank T1 - Finite element mesh design of a cylindrical cask under puncture drop test conditions N2 - Transport casks for radioactive materials have to withstand the 9 m drop test, 1 m puncture drop test and dynamic crush test with regard to the mechanical requirements according to the IAEA regulations. The safety assessment of the package can be carried out on the basis of experimental investigations with prototypes or models of appropriate scale, calculations, by reference to previous satisfactory safety demonstrations of a sufficiently similar nature or a combination of these methods. Computational methods are increasingly used for the assessment of mechanical test scenarios. However, it must be guaranteed that the calculation methods provide reliable results. Important quality assurance measures at the Federal Institute for Materials Research and Testing are given concerning the preparation, run and evaluation of a numerical analysis with reference to the appropriate guidelines. Hence, a successful application of the finite element (FE) method requires a suitable mesh. An analysis of the 1 m puncture drop test using successively refined FE meshes was performed to find an acceptable mesh size and to study the mesh convergence using explicit dynamic FE codes. The FE model of the cask structure and the puncture bar is described. At the beginning a coarse mesh was created. Then this mesh was refined in two steps. In each step the size of the elements was bisected. The deformation of the mesh and the stresses were evaluated dependent on the mesh size. Finally, the results were extrapolated to an infinite fine mesh or the continuous body, respectively. The uncertainty of the numerical solution due to the discretisation of the continuous problem is given. A safety factor is discussed to account for the uncertainty. KW - IAEA puncture drop test KW - Cylindrical cask KW - FE mesh refinement KW - Explicit dynamics KW - Numerical analysis PY - 2011 DO - https://doi.org/10.1179/1746510911Y.0000000008 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 22 IS - 2 SP - 112 EP - 116 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-24016 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hansen, H.-C. A1 - Lagrèze, W. A1 - Krüger, Oswald A1 - Helmke, K. T1 - Dependence of the optic nerve sheath diameter on acutely applied subarachnoidal pressure - an experimental ultrasound study N2 - Purpose: To determine the distensibility and elastic characteristics of the optic nerve sheath for development of a basic understanding of ultrasound studies aimed to measure optic nerve sheath diameter (ONSD) for detection of acutely elevated intracranial pressure (ICP). Methods: Isolated human optic nerves preparations obtained from autopsies were submitted to predefined pressure alterations, and consecutive changes in ONSD were measured by B-scan ultrasound under defined conditions. Results: Following submission to pressure, the diameter of the nerve sheath increased up to 140% of its baseline value. The increase (mean 1.97 mm, SD 0.52 mm) corresponded to the magnitude of pressure steps measured in the perineural subarachnoidal space (SAS). Similarly, the ONSD declined in each of the preparations within a few minutes after the optic nerve was decompressed. However, it did not reach its baseline value again when pressure loads of 45–55 mmHg or more had been applied. Conclusions: The elasticity of the anterior sheath of the optic nerve is sufficient for the detection of pressure changes in the SAS especially for upward pressure steps. This is basically important for the application of clinical monitoring of the sheath diameter to facilitate the identification of patients with elevated ICP non-invasively (screening). However, further implementation of this procedure in neurointensive care and emergency medicine has to consider that the sheath diameter reversibility may be impaired after episodes of prolonged intracranial hypertension and a model for hysteresis is proposed. KW - Intensive care KW - Intracranial pressure KW - Neuromonitoring KW - Optic nerve sheath KW - Ultrasound PY - 2011 DO - https://doi.org/10.1111/j.1755-3768.2011.02159.x SN - 1755-375X SN - 1755-3768 VL - 89 IS - 6 SP - e528 EP - e532 PB - Blackwell CY - Oxford AN - OPUS4-24017 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberstein, M. A1 - Geier, M. A1 - Partsch, U. A1 - Völkel, L. A1 - Böhme, R. A1 - Pentzien, Simone A1 - Koter, Robert A1 - Mann, Guido A1 - Bonse, Jörn A1 - Krüger, Jörg T1 - Towards an industrial laser doping process for the selective emitter using phosphoric acid as dopand T2 - 26th European Photovoltaic Solar Energy Conference CY - Hamburg, Germany DA - 2011-09-06 PY - 2011 AN - OPUS4-23968 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Poppenberg, J. A1 - Richter, S. A1 - Traulsen, C. H.-H. A1 - Darlatt, Erik A1 - Unger, Wolfgang A1 - Schalley, C. A. T1 - Controlled Preparation of a Pyridyl-Terminated SAM on Gold - a Promising Platform for Layer-by-Layer Self-Assembly through Metal Coordination T2 - Supramolecules & Assemblies, Chemistry Properties and Organization at Multiple Scales CY - Lucca, Italy DA - 2011-06-19 PY - 2011 AN - OPUS4-23969 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, S. A1 - Poppenberg, J. A1 - Darlatt, Erik A1 - Traulsen, C. H.-H. A1 - Tatzke, M. A1 - Dzyuba, E. V. A1 - Sattler, D. A1 - Unger, Wolfgang A1 - Schalley, C. A. T1 - Metal Coordinated Layer-by-Layer Self-Assembly of Macrocycles and Rotaxanes on Gold Surfaces T2 - Supramolecules & Assemblies, Chemistry Properties and Organization at Multiple Scales CY - Lucca, Italy DA - 2011-06-19 PY - 2011 AN - OPUS4-23970 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühn, Julius T1 - Introduction into Surface and Thin Film Analysis of Ternary Pd-Ni-Co Alloys for Hydrogen Sensor Purposes T2 - Physical Chemistry Seminar (Humboldt-Universität zu Berlin) CY - Berlin, Germany DA - 2011-06-24 PY - 2011 AN - OPUS4-23971 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schalau, Bernd A1 - Hauschild, J. A1 - Andernacht, M. T1 - Zur probabilistischen Bewertung des EVA-Ereignisses "Explosionsdruckwelle" T2 - Probabilistische Sicherheitsanalysen in der Kerntechnik CY - Heidelberg, Germany DA - 2011-05-26 PY - 2011 AN - OPUS4-23975 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gnutzmann, Tanja A1 - Klimakow, Maria A1 - Rademann, K. A1 - Emmerling, Franziska T1 - In situ characterization of crystallization processes applying synchrotron XRD and Raman spectroscopy T2 - International School of Crystallography - 44th Course The Power of Powder Diffraction CY - Erice, Italy DA - 2011-06-02 PY - 2011 AN - OPUS4-23976 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bartholmai, Matthias A1 - Köppe, Enrico A1 - Neumann, Patrick P. T1 - Sensor Technologies and Electronic Systems T2 - KCESS 2011, Kuwait Conference on e-Services and e-Systems CY - Kuwait City, Kuwait DA - 2011-04-05 PY - 2011 AN - OPUS4-24038 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bartholmai, Matthias A1 - Pettelkau, Alexander A1 - Goedecke, Thomas A1 - Daum, Werner A1 - Farahbakhsh, Mahin A1 - Hohendorf, Stefan A1 - Damm, David T1 - "Intelligente"IBC für eine sichere und wirtschaftliche Gefahrgutlogistik T2 - Workshop des BMVBS zu Telematikanwendungen bei der Beförderung gefährlicher Güter während der Messe "transport logistic 2011" CY - Munich, Germany DA - 2011-05-10 PY - 2011 AN - OPUS4-24039 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bartholmai, Matthias A1 - Werner, Klaus-Dieter T1 - Langzeitmonitoring am Berliner Hauptbahnhof N2 - Problemstellung: - größter Turmbahnhof Europas - Bau auf nachgiebigem Sandboden - weitere Baumaßnahmen in unmittelbarer Nähe - Setzungen und Hebungen der Brückenfundamente - resultierende Beanspruchungen der Konstruktion - Erfassung der Beanspruchungen und Verformungen während Bau und Betrieb - Möglichkeit der Nachstellung der Gabelstützen T2 - VDI/VDE-Expertenforum im Rahmen der Messe "Sensor und Test 2011" CY - Nuremberg, Germany DA - 07.06.2011 PY - 2011 AN - OPUS4-24040 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner A1 - Schukar, Vivien A1 - Münzenberger, Sven A1 - Gründer, Klaus-Peter A1 - Habel, Wolfgang T1 - Experimental Validation Technique for Strain Transfer Characterization of Fibre Optic Strain Sensors T2 - International Conference on Applications for Image based Measurements CY - Ulm, Germany DA - 2011-03-22 PY - 2011 AN - OPUS4-24042 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner T1 - Monitoring im Spiegelbild von Technik, Recht und Regelwerken T2 - VDI/VDE-GMA-Expertenforum Strukturmonitoring und Zustandsüberwachung 2011 - Schadensfällen vorbeugen - Instandhaltung optimieren CY - Nuremberg, Germany DA - 2011-06-07 PY - 2011 AN - OPUS4-24043 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Günther, Alexander A1 - Gründer, Klaus-Peter T1 - New Bispectral Measurement Device for Fluorescent Materials T2 - 27th Session of the CIE 2011 CY - Sun City, South Africa DA - 2011-07-10 PY - 2011 AN - OPUS4-24044 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Günther, Alexander A1 - Gründer, Klaus-Peter T1 - Neuer Messaufbau zur bispektralen Messung der Reflexionseigenschaften von fluoreszierenden Materialien T2 - COSP 2011 CY - Berlin, Germany DA - 2011-03-21 PY - 2011 AN - OPUS4-24045 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Günther, Alexander A1 - Gründer, Klaus-Peter T1 - Messaufbau zur bispektralen Messung der Fluoreszenzeigenschaften von reflektierenden Materialien T2 - DGaO-Jahrestagung CY - Ilmenau, Germany DA - 2011-06-14 PY - 2011 AN - OPUS4-24046 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Basedau, Frank T1 - Langzeitmonitoring der Ederstaumauer N2 - Die Fixierung der Stahlanker im Felsfundament zur Stabilisierung der Schwergewichtsmauer werden mit integrierten faseroptischen Dehnungssensoren überwacht. In die Glasfaser sind Reflektoren eingebaut; zwei Reflektoren bilden jeweils eine Messstrecke, die Auskunft über die Fixierung geben. Am Ankerkopf wird der Zustand der Messstrecken abgefragt. T2 - Expertenforum Strukturmonitoring auf der Sensor+Test-Messe CY - Nuremberg, Germany DA - 08.06.2011 PY - 2011 AN - OPUS4-24047 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Umsetzung der Ökodesignrichtlinie in Deutschland T2 - "Ökodesign und Energieeffizienz von energiebetriebenen Produkten" CY - Würzburg, Germany DA - 2011-07-20 PY - 2011 AN - OPUS4-23999 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Umsetzung der Ökodesignrichtlinie in Deutschland T2 - "Okodesign und Energieeffizienz von energiebetriebenen Produkten" CY - Nuremberg, Germany DA - 2011-07-21 PY - 2011 AN - OPUS4-24000 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nitsche, Michael T1 - Der Akkreditierungsbeirat (AKB) und die Gremien der DAkkS - Mitwirkungsmöglichkeiten für interessierte Kreise T2 - 17. EUROLAB-D Kolloquium CY - Berlin, Germany DA - 2011-05-06 PY - 2011 AN - OPUS4-24002 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wan, Wei A1 - Biyikal, Mustafa A1 - Wagner, R. A1 - Sellergren, B. A1 - Rurack, Knut T1 - Hydrogen Bonding vs. Deprotonation: Binding of a Chromogenic Functional Monomer towards a Template in Molecular Imprinting Polymerization T2 - Affinity 2011 CY - Tavira, Portugal DA - 2011-06-16 PY - 2011 AN - OPUS4-24007 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wloka, Monika T1 - Änderung in der ISO/IEC 17021:2011 - Schwerpunkt Auditorenkompetenz T2 - Erfahrungsaustausch Auditoren bei Buerau Vertitats CY - Hamburg, Germany DA - 2011-06-17 PY - 2011 AN - OPUS4-23958 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wloka, Monika T1 - Überblick über zurzeit in Revision befindliche Normen für akkreditierte Stellen T2 - World Accreditation Day CY - Berlin, Germany DA - 2011-06-09 PY - 2011 AN - OPUS4-23959 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kautek, W. A1 - Krüger, Jörg A1 - Grabner, G. A1 - Dexl, Alois K. A1 - Trautinger, F. A1 - Hertwig, Andreas T1 - Femtosecond laser interaction with cornea and dermal tissues T2 - Bunsentagung 2011 CY - Berlin, Germany DA - 2011-06-02 PY - 2011 AN - OPUS4-23963 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koenders, L. A1 - Busch, I. A1 - Hinze, P. A1 - Senoner, Mathias T1 - Normale für die Nanometrologie und -analytik T2 - 16. Tagung Festkörperanalytik CY - Vienna, Austria DA - 2011-07-04 PY - 2011 AN - OPUS4-23964 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dietrich, Paul A1 - Unger, Wolfgang T1 - Entwicklung einer normativen analytischen Infrastruktur für die Qualitätssicherung von Mikroarrays T2 - 3. Berlin-Brandenburger Technologieforum In Vitro-Diagnostik und Bioanalytik CY - Potsdam, Germany DA - 2011-06-09 PY - 2011 AN - OPUS4-23965 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Girard-Lauriault, Pierre-Luc A1 - Dietrich, Paul A1 - Gross, Thomas A1 - Unger, Wolfgang T1 - Quantitative Chemical Determination of Organic Layers using CDXPS: A Valid Experimental Procedure? T2 - Research Seminar INP Greifswald e. V. CY - Greifswald, Germany DA - 2011-05-26 PY - 2011 AN - OPUS4-23967 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Urs A1 - Schlegel, Moritz-Caspar A1 - Emmerling, Franziska T1 - Advanced techniques for the studying damage mechanisms of cementitious matrices affected by sulfate attack T2 - 13th European Seminar on Microscopy Applied to Building Materials CY - Ljubljana, Slovenia DA - 2011-06-14 PY - 2011 AN - OPUS4-24018 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Potentials and Borders of the Customisation of Repair Mortars by Mixture Modification T2 - 16th International Conference on Composites Structures (ICCS16) CY - Oporto, Portugal DA - 2011-06-28 PY - 2011 AN - OPUS4-24021 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Properties of Repair Mortars - Potentials and Risks of a Tailor-made Mixture Proportioning T2 - Concrete-Workshop "Performance-based Specifications for Concrete" CY - Leipzig, Germany DA - 2011-06-14 PY - 2011 AN - OPUS4-24022 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stegemann, B. A1 - Richter, M. A1 - Schultz, C. A1 - Pahl, H.-U. A1 - Endert, H. A1 - Bonse, Jörn A1 - Rau, B. A1 - Quaschning, V. A1 - Fink, F. T1 - One wavelength fits all N2 - Structuring of Thin-film Solar Cells with a Single Laser Wavelength Structuring of a PV module into a number of cells is necessary to lower the current and to increase the voltage, and is typically accomplished with nanosecond laser pulses of different wavelengths. Duetothe many available laser sources, complex and expensive scribing Setups are necessary. To overcome this a concept for laser structuring of thin-film PV modules using a single wavelength allows prediction ofthe ablation behaviourfor a given laser pulse energy. KW - Thin-film solar cells KW - Nanosecond laser ablation KW - 532 nm wavelength KW - Laser scribing KW - Damage threshold PY - 2011 SN - 1869-8913 VL - 2 IS - 6 SP - 46 EP - 48 PB - Hüthig CY - Heidelberg AN - OPUS4-24158 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Jann, Oliver ED - Czichos, Horst ED - Saito, T. ED - Smith, L. T1 - Emissions from Materials N2 - Emissions from materials influence the surrounding environment. Gaseous emissions - mainly volatile organic compounds (VOCs) - into indoor air are of Special interest due to the fact that they affect indoor air Quality (IAQ). VOCs are of importance because they are strongly related to the so-called sick-building Syndrome (SBS). Materials are not the only source of indoor air pollution. Other important sources are every type of combustion (e.g. fire places, gas cooking), especially smoking (environmental tobacco smoke (ETS)) and the use of household Chemicals (sprays, solvents e.g.). Whereas these kinds of sources can be influenced by the user (to use or not to use it) materials emissions cannot be influenced by the user to the same extent. Often the user is simply not aware that materials might have emissions. PY - 2011 SN - 978-3-642-16640-2 SP - 860 EP - 869 PB - Springer CY - Berlin, Heidelberg AN - OPUS4-24159 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kadenkin, Alexander A1 - Broekaert, J.A.C. T1 - Studies with a miniaturized microwave induced plasma for element specific detection in gas chromatographic separations of halogenated hydrocarbons N2 - The possibilities of a helium microstrip microwave induced plasma, operated at less than 40 W and less than 250 mL min-1 of gas, as source for optical emission spectrometry (MSP-OES) were studied for the element specific detection of halogenated volatile organic compounds, such as chlorinated and brominated alkanes and arenes, after their separation by capillary gas chromatography (GC). After hyphenation of the GC with MSP-OES with the aid of a heated transfer line, different gas chromatographic parameters, like the carrier gas flow (1.4–3.3 mL min-1) and the oven temperature (100–200), as well as different plasma specific parameters, like the forward power (30–40 W) and the plasma gas flow (100–200 mL min-1), were optimized. In the next step, rotational and excitation temperatures of microstrip plasma were studied in dependence on analyte concentrations between 1 and 10% v/v in pentane and found to be in the order of 1250–1650, as measured with OH bands, and 6100–6900 K, as measured with Fe-lines from ferrocene vapor entered in the plasma gas, respectively. Further, it could be shown that the hyphenated technique GC-MSP-OES can be used for the determination of volatile halogenated organic compounds under the use of an internal standard with recovery rates at the order of 90–110% at the 2–5 mg g-1 level. The absolute limits of detection for volatile halogenated organic compounds, obtained with GC-MSP-OES and the Cl I 837.594 nm, Br I 827.244 nm and C I 247.856 nm, were found to be in the ng-range and the relative detection limits in pentane in the µL L-1 range. KW - Gas chromatography KW - Microwave induced plasma PY - 2011 DO - https://doi.org/10.1039/c1ja10028a SN - 0267-9477 SN - 1364-5544 VL - 26 IS - 7 SP - 1481 EP - 1487 PB - Royal Society of Chemistry CY - London AN - OPUS4-24160 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kadenkin, Alexander A1 - Amberger, M. A1 - Fittschen, U.E.A. A1 - Broekaert, J.A.C. T1 - Micro-homogeneity studies of boron carbide powders N2 - We have studied the micro-homogeneity of boron carbide powders by inductively coupled Plasma optical emission spectrometry (ICP-OES) and total reflection X-ray fluorescence spectrometry (TXRF) using slurry sampling. To get information on the particle size distributions of the powders, the stabilized slurries of boron Carbide powders were nebulized, the aerosols were transported into a Batelle impactor and the droplets were collected on the impactor stages bearing TXRF sample holders. In a first series of measurements, parameters of the impaction like the duration of the impaction and the use of glutinous substance on the sample holders were optimized. The different mass size fractions for industrial boron Carbide powders were determined by weight measurements of the fractions collected on the different stages. The established particle size distributions were in the range of 0.5 to >16 µm and found similar to those determined by laser diffraction reported elsewhere. Analyses of the mass fractions by slurry sampling TXRF showed that Ca, Ti, Cr, Mn, Fe, Ni and Cu within the measurements errors were homogeneously distributed over the mass fractions between 0.5 and 4 µm and that their concentrations agreed with the bulk composition, as determined with ICP-OES subsequent to digestion. However, light underestimates were found at the 5 (Mn) up to 150 µg g-1 (Fe) level. Finally, boron carbide powders were washed out with nitric acid with different concentrations and leaching solutions and the residues were analyzed by ICP-OES and TXRF respectively. It is shown that up to 60% of the residual trace impurities in the powder studied can be removed by leaching with 34% (v/v) of nitric acid. KW - Boron carbide KW - Micro-homogeneity KW - ICP-OES KW - TXRF KW - Impaction PY - 2011 DO - https://doi.org/10.1007/s00604-011-0546-y SN - 0026-3672 SN - 1436-5073 VL - 173 IS - 1-2 SP - 183 EP - 188 PB - Springer CY - Wien AN - OPUS4-24161 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pittner, Andreas A1 - Schwenk, Christopher A1 - Rethmeier, Michael A1 - Karkhin, V.A. T1 - Simulation of Welding Temperature Field in Laser Beam Welding by Inverse Techniques T2 - 13th NOLAMP, Conference on Laser Materials Processing in the Nordic Countries CY - Trondheim, Norway DA - 2011-06-27 PY - 2011 AN - OPUS4-24162 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thöns, Sebastian A1 - Faber, M.H. A1 - Rücker, Werner T1 - On the utilization of monitoring data in an ultimate limit state reliability analysis T2 - 11th International Conference on Applications of Statistics and Probability in Civil Engineering (ICASP) CY - Zurich, Switzerland DA - 2011-08-01 PY - 2011 AN - OPUS4-24163 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Karkhin, Victor A1 - Pittner, Andreas A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - Simulation of inverse heat conduction problems in fusion welding with extended analytical heat source models N2 - The paper presents bounded volume heat sources and the corresponding functional-analytical expressions for the temperature field. The power density distributions considered here are normal, exponential and parabolic. The sources model real heat sources like the welding arc, laser beam, electron beam, etc., the convection in the weld pool as well as the latent heat due to fusion and solidification. The parameters of the heat source models are unknown a priori and have to be evaluated by solving an inverse heat conduction problem. The functional-analytical technique for calculating 3D temperature fields in butt welding is developed. The proposed technique makes it possible to reduce considerably the total time for data input and solution. It is demonstrated with an example of laser beam welding of steel plates. KW - Laser beam welding KW - Volume heat source KW - Functional-analytical solution KW - Inverse modelling PY - 2011 DO - https://doi.org/10.1007/s11706-011-0137-1 SN - 2095-025X SN - 2095-0268 VL - 5 IS - 2 SP - 119 EP - 125 PB - Springer CY - Secaucus, N.J. AN - OPUS4-24164 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Karkhin, Victor A1 - Pittner, Andreas A1 - Schwenk, Christopher A1 - Rethmeier, Michael ED - Halmoy, E. T1 - Simulation of the temperature field in laser beam welding by inverse technique N2 - This paper presents volume heat sources and the corresponding functional analytical Solutions for the transient temperature field. The considered energy distributions are normal, exponential and parabolic. The method follows the common approach in Computational Welding Mechanics (CWM) to account for the physics of the welding process and the resulting temperature field by phenomenological models for heat conduction. Therefore, the used heat source models are apparent heat sources that incorporate the real heat input as well as the fluid flow in the weld pool and the latent heat connected with phase transformations. The heat source models provide welding characteristics like thermal cycle and Fusion line in the cross section within short computational time. Consequently, inverse techniques on basis of optimisation algorithms enable the adaptation of the models to the experimental data efficiently. Furthermore, the direct evaluation of the energy distribution for the experimental fusion line in the cross section is demonstrated which enhances the numerical optimisation by reducing the number of unknown model Parameters and providing a reasonable initial guess within the model parameter space. The proposed temperature field models are validated with real laser beam welding experiments. T2 - 13th Conference on laser materials processing in the nordic countries CY - Trondheim, Norway DA - 27.06.2011 KW - Volume heat source KW - Inverse modelling KW - Functional analysis KW - Laser beam welding PY - 2011 SP - 223 EP - 234 AN - OPUS4-24165 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sievert, Rainer T1 - A geometrically nonlinear elasto-viscoplasticity theory of second grade N2 - A general concept for the consideration of the influence of strain gradients on elasto-viscoplastic material behaviour at finite deformation is presented that does not need to account for an additional flow rule for the plastic strain gradient. The balance of momentum including the representation of the stresses, the power of work at contact for the formulation of boundary conditions as well as the nonlocal form of the total power of deformation are derived via the dissipation inequality for the investigated nonpolar continuum model of second grade. In addition to the gradient of the elastic strain tensor, energy storage with gradients of different internal variables is considered: gradient of (i) the plastic strain Tensor itself, (ii) an internal strain tensor induced by viscoplastic straining, by which energy due to hardening is stored also with ist gradient, and (iii) scalar internal variables like the accumulated viscoplastic strain or an internal time variable of damage. Finally, for the simulation of the damage behaviour during a strain hold-time period at a crack tip the responses of a ratedependent and a quasi-rate-independent gradient-enhanced damage model are compared in finite element studies. KW - Viscoplasticity KW - Plasticity KW - Strain-gradient KW - Finite deformation PY - 2011 UR - http://www.uni-magdeburg.de/ifme/zeitschrift_tm/2011_Heft2/01_Sievert.pdf SN - 0232-3869 VL - 31 IS - 2 SP - 83 EP - 111 PB - Institut für Mechanik CY - Magdeburg AN - OPUS4-24166 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Skrotzki, Birgit A1 - Koch, B. T1 - Microstructural characterization of the metastable Beta-titanium alloy TIMETAL LCB after fatigue loading N2 - In the present work, the titanium alloy Ti-6.8Mo-4.5Fe-1.5Al (Timetal LCB) was investigated with respect to the microstructural evolution during strain controlled fatigue loading. The alloy was developed to reduce the generally high material costs of β-alloys by substituting expensive beta stabilizers by using a standard Fe-Mo master alloy. One possible application seen in the automotive industry is the substitution os suspension structural parts currently made of steel, suc as suspension springs. These components require a high strength and fatigue resistance. T2 - International conference on electron nanoscopy & XXXII Annual meeting of EMSI CY - Hyderabad, India DA - 2011-07-06 KW - Titanium KW - Fatigue KW - Microstructure KW - Deformation mechanism PY - 2011 SP - 255 EP - 256 AN - OPUS4-24167 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stark, Wolfgang A1 - Jaunich, Matthias T1 - Thermoanalytische Charakterisierung von Ethylen-Vinylacetat-Copolymer (EVA) für Photovoltaikmodule N2 - Das Ziel der Untersuchungen war mit Hilfe von DSC und DMA EVA-Folien im Anlieferungszustand hinsichtlich der Lage der Glasübergangstemperatur, des Schmelzverhaltens und der Temperaturabhängigkeit der Vernetzungsreaktion zu charakterisieren. Auf dieser Basis sollte die Lieferstabilität im Sinne einer Wareneingangskontrolle auf eine messtechnische Basis gestellt werden. In einem 2. Schritt sollte die vernetzte Folie dahingehend charakterisiert werden, ob infolge der Vernetzung eine Änderung der KW - Photovoltaik KW - Klebfolie KW - EVA KW - DSC KW - DMA PY - 2011 VL - 8 SP - 3 EP - 5 AN - OPUS4-24168 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bachmann, Marcel A1 - Avilov, Vjaceslav A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - CFD simulation of the liquid metal flow in high power laser welding of aluminium with electromagnetic weld pool support T2 - 2nd International conference on fluid mechanics and heat and mass transfer 2011 CY - Corfu, Greece DA - 2011-07-14 KW - Electromagnetic weld pool support KW - Laser beam welding KW - Lorentz force KW - Marangoni stresses KW - Natural convection PY - 2011 SN - 978-1-61804-020-6 SP - 179 EP - 184 PB - WSEAS Press AN - OPUS4-24171 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Molnarne, Maria A1 - Schröder, Volkmar T1 - Comparison of calculated data for the flammability and the oxidation potential according to ISO 10156 with experimentally determined values N2 - The classification of flammable gas mixtures is based on either testing or calculation methods proposed by the revised international standard ISO 10156. This standard is used for classification of physical hazards in Chapters 2.2 and 2.4 of the UN Globally Harmonized System of Classification and Labelling of Chemicals (GHS) and in the UN Recommendations on Transport of Dangerous Goods (TDG). The test methods of flammability and oxidizing potential in this standard were developed by BAM. Earlier versions of this standard are not based on triangular diagrams and on the reference combustible substance 'ethane'. The old material characteristics, especially in case of oxidizing potential, are based mostly on practical experience without any quantifiable test results. First time it is possible to compare experimental results from the CHEMSAFE database with the newly developed calculation method. In this paper the basic principles of the calculation methods are presented and the methods are validated by examples. A comparison of experimental flammability data with classification results gained by the calculation methods of ISO 10156 is demonstrated. KW - Gas classification KW - GHS KW - Flammability limit KW - Oxidizing potential KW - Calculation method PY - 2011 DO - https://doi.org/10.1016/j.jlp.2011.06.024 SN - 0950-4230 SN - 1873-3352 VL - 24 IS - 6 SP - 900 EP - 907 PB - Elsevier Ltd. AN - OPUS4-24176 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Österle, Werner A1 - Dmitriev, Andrey T1 - Functionality of conventional brake friction materials - Perceptions from findings observed at different length scales N2 - Automotive braking is based on dry friction between fixed pads and a rotating disc. Besides macroscopic thermo-physical properties, the development of topographic features on the mesoscopic scale and the nanostructure of the third body formed by wear processes, determine brake performance properties. Whereas modelling on the atomistic scale is suitable to understand mechanisms leading to nanocrystalline surface films, the properties of such films can be assessed best with a model based on movable cellular automata (MCA). It turned out that the presence of at least 10% of soft nanoinclusions is most essential in respect to smooth sliding conditions. It made no major difference whether graphite or copper particles were assumed as soft nanoinclusions. The third body material is not only the stuff which spreads over contact areas, but it also contributes to contact size by wear particle compaction and formation of secondary contact areas. The evolution of contact size is the major feature of mesoscopic modelling and thus it is capable to model and explain dynamic changes of the coefficient of friction (COF) during certain brake operations. Although it is still ambiguous in many cases which feature has the major impact on friction behaviour, the following conclusions can be drawn. The reinforcing ingredients of the pad material serve as primary contact sites and thus define the starting condition for mesoscopic simulations. A certain amount of wear is necessary to provide a third body which is capable to form secondary contact sites and friction layers screening the first body materials. The composition and nanostructure of the third body is important as well, because it determines the friction level and is responsible for smooth sliding conditions. KW - Nanostructure KW - Microstructure KW - Mesostructure KW - Macrostructure KW - Modelling KW - Simulation PY - 2011 DO - https://doi.org/10.1016/j.wear.2010.11.035 SN - 0043-1648 VL - 271 IS - 9-10 SP - 2198 EP - 2207 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-24177 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan A1 - Salge, T. A1 - Terborg, R. A1 - Rackwitz, Vanessa T1 - Advanced Elemental Analysis with ED-EPMA, WD-EPMA and µ-XRF at a SEM T2 - Microscopy & Microanalysis 2011 Meeting CY - Nashville, TN, USA DA - 2011-08-07 PY - 2011 AN - OPUS4-24149 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kromm, Arne T1 - Exploring the Interaction of Phase Transformation and Residual Stress during Welding by Synchrotron Diffraction T2 - 64th IIW Annual Assembly CY - Chennai, India DA - 2011-07-17 PY - 2011 AN - OPUS4-24150 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schempp, Philipp A1 - Cross, Carl Edward A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - Influence of Ti and B additons on grain size and weldability of aluminium alloy 6082 T2 - 64th Annual Assembly & International Conference of the International Institute of Welding CY - Chennai, India DA - 2011-07-17 PY - 2011 AN - OPUS4-24151 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Woydt, Mathias A1 - Kelling, Norbert A1 - Hannemann, F. A1 - Berberich, N. A1 - Ziegele, H. T1 - Stribeck-type curves of alternative engine oils. Part I: Gray cast iron liners T2 - Tribologie-Fachtagung 2011 CY - Göttingen, Germany DA - 2011-09-26 PY - 2011 AN - OPUS4-24152 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ferrero, Fabio A1 - Kluge, Martin A1 - Kreißig, Michael A1 - Schmidtchen, Ulrich A1 - Holtappels, Kai T1 - Prevention of the explosion of acetylene cylinders involved in fire: experiments and simulations N2 - In order to assess the effectiveness of water cooling of acetylene cylinders involved in fire, a total of 13 bonfire tests with 8.9-, 10 and 50-l-cylinders were performed. During the experiments the pressure in the cylinder and the temperature at different locations within the porous material and on the Shell surface as well as the flame temperature were measured. Overall 8 burst tests were performed, in order to determine the times to explosion for the cylinders. Cylinders failed not later than 15 minutes from the ignition of the bonfire, often with generation of a fireball. During the other 5 tests, the fire was extinguished before the expected burst and the cylinder was cooled with water. In 2 of the 5 extinction experiments, the explosion of the cylinder could be prevented. Noticeably, in one case the on-set of the decomposition of acetylene had already been observed, before the cooling was started. In spite of that, the cooling was still effective. The interpretation of the current results and of the data from previous tests with 40-l-cylinder suggests that single acetylene cylinders involved in fire might be saved by cooling, if their pressure does not exceed a value of about 45 bara. The recorded values of pressure and temperature were used to develop and validate a mathematical model for the prediction of the heat transfer in acetylene cylinders during the exposure to fire and the afterward cooling. The predictions agreed well with the experimental results. T2 - 23rd ICDERS 2011 CY - Irvine, CA, USA DA - 24.07.2011 KW - Acetylene KW - Gas cylinders KW - Fire exposure KW - Decomposition PY - 2011 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. IS - Paper 132 SP - 1 EP - 6 AN - OPUS4-24153 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Matthias A1 - Jann, Oliver A1 - Kemski, J. A1 - Klingel, R. A1 - Schneider, Uwe A1 - Krocker, Christian T1 - Investigations on radon exhalation of different building materials N2 - The inhalation of 222Rn (radon) is one of the most important reasons for lung cancer, after smoking. Usually, the geological subsoil and the building ground are the dominant sources for enhanced indoor radon levels. Additionally, building materials can increase indoor radon concentrations when these materials contain higher contents of 226Ra (radium), especially in combination with low air exchange rates. For a realistic estimation of indoor radon concentrations, it is helpful to carry out measurements of radon exhalation rates from relevant materials using emission test chambers. In Germany, it is aspired to limit the total indoor radon concentration to 100 Bq/m3, whereby building materials should contribute at most 20 Bq/m3. Within a project financed by the German Institute for Construction Technology (DIBt), a practical oriented measurement procedure of the radon exhalation of building materials in accordance to ISO 16000-9 was developed to have a means for the assessment of these materials with respect to their indoor use. Test chambers with different volumes were used. The tested materials were mainly used for wall constructions (e.g., bricks, light-weight concrete) and have known specific radium activities and radon exhalation rates. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - Radon exhalation KW - Building material KW - Emission test chamber KW - Indoor air PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-24155 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pauli, Jutta A1 - Grabolle, Markus A1 - Brehm, Robert A1 - Spieles, Monika A1 - Hamann, F.M. A1 - Wenzel, M. A1 - Hilger, I. A1 - Resch-Genger, Ute T1 - Suitable labels for molecular imaging - influence of dye structure and hydrophilicity on the spectroscopic properties of IpG conjugates N2 - Aiming at the design of highly brilliant NIR emissive optical probes, e.g., for in vivo near-infrared fluorescence imaging (NIRF), we studied the absorption and fluorescence properties of the asymmetric cyanines Dy678, Dy681, Dy682, and Dy676 conjugated to the model antibody IgG. The ultimate goal was here to derive general structure–property relationships for suitable NIR fluorescent labels. These Dy dyes that spectrally match Cy5 and Cy5.5, respectively, were chosen to differ in chromophore structure, i.e., in the substitution pattern of the benzopyrylium end group and in the number of sulfonic acid groups. Spectroscopic studies of the free and IgG-bound fluorophores revealed a dependence of the obtained dye-to-protein ratios on dye hydrophilicity and control of the fluorescence quantum yields (Φf) of the IgG conjugates by the interplay of different fluorescence reduction pathways like dye aggregation and fluorescence resonance energy transfer (FRET). Based upon aggregation studies with these dyes, the amount of dye dimers in the IgG conjugates was determined pointing to dye hydrophilicity as major parameter controlling aggregation. To gain further insight into the exact mechanism of dye dimerization at the protein, labeling experiments at different reaction conditions but constant dye-to-protein ratios in the reaction solution were performed. With Dy682 that displays a Φf of 0.20 in PBS and 0.10 for moderate dye-to-protein ratio of 2.5, a low aggregation tendency, and a superior reactivity in IgG labeling, we identified a promising diagnostic tool for the design of NIR fluorescent probes and protein conjugates. KW - In vivo fluorescence imaging KW - NIR fluorophore KW - Fluorescence quantum yield KW - Cyanine KW - IpG KW - Protein labelling KW - Aggregation KW - Homo-FRET PY - 2011 DO - https://doi.org/10.1021/bc1004763 SN - 1043-1802 SN - 1520-4812 VL - 22 IS - 7 SP - 1298 EP - 1308 PB - ACS Publications CY - Washington, DC AN - OPUS4-24156 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Wrought iron arch bridge: measurements and materials testing N2 - In 1882, the East-West suburban train viaduct was built through Berlin as part of the public traffic solution in the late 19th Century. Today, the only left over iron arch bridge is a pair of two arches Crossing the Spree river in the middle of Berlin. Before dismantling the former parallel two original pairs of iron arches and rebuilding new arches for the high-speed railway line through Berlin in 1997, BAM was involved in an extensive test program of the heritage iron arch structure. Especially the estimation of accumulated damage in critical details and the verification of the old material properties at early stage was important information to the bridge owners. The testing program included two strain and displacement measurement campaigns, non-destructive testing, materials testing and microscale metallographic analysis of critical details. The measured strain cycles were significant lower in number and size than expected. Most of the cycles were compression stress cycles only. The work was planned in Cooperation with the Berlin consultancy Professor Hilbers that was responsible for the design and calculation of the reconstruction measures. Additionally, after calculation of the possible reuse of the old arches, we compared measured data from strain measurements with the results from calculation. The measured data and the calculated data show a good qualitative correlation. T2 - 12th ICMS - Progress in steel and composite structures CY - Wroclaw, Poland DA - 15.06.2011 KW - Iron arch bridge KW - Strain measurement KW - Displacement measurement KW - Tension test KW - Crack propagation test KW - Magnetic powder test PY - 2011 SN - 978-83-7125-202-0 SP - 1 EP - 8 AN - OPUS4-24157 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wettmarshausen, Sascha A1 - Min, Hyegeun A1 - Unger, Wolfgang A1 - Jäger, Christian A1 - Hidde, Gundula A1 - Friedrich, Jörg Florian T1 - Significance of hydrogen-deuterium exchange at polyolefin surfaces on exposure to ammonia low-pressure plasma N2 - Since more than 40 years ammonia plasma exposure of polyolefins is used for introduction of primary amino groups. The selectivity of this reaction and the yield in primary amino groups was found to be low. Here, a prominent side-reactions of this process was investigated, the hydrogenation by NH3 plasma. For identification of hydrogenation ammonia (NH3) and deuterated ammonia (ND3) were exposed to Polyethylene (h-PE) and fully deuterated polyethylene (d-PE) as well as hexatriacontane (h-HTC) and fully deuterated hexatriacontane (d-HTC) as low-molecular weight model for PE. H–D exchange was assumed and detected by Time-of-Flight Secondary Ion Mass Spectrometry (ToF–SIMS), X-ray Photoelectron Spectroscopy (XPS), Attenuated Total Reflectance (ATR-FTIR) and 1H and 2H Nuclear magnetic Resonance. Results show a significant H–D exchange within the sampling depth of ATR (2.5 µm). However, N- and NH2 introduction was limited to the topmost surface as shown by SIMS and XPS (a few nanometers). KW - Deuterated ammonia KW - Ammonia plasma KW - Deuterated polyolefins KW - Hexatriacontane KW - H-D exchange PY - 2011 DO - https://doi.org/10.1007/s11090-011-9304-5 SN - 0272-4324 VL - 31 IS - 4 SP - 551 EP - 572 PB - Plenum Publ. Corp. CY - New York, NY, USA AN - OPUS4-24178 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Daum, Werner ED - Czichos, Horst ED - Saito, T. ED - Smith, L. T1 - Structural Health Monitoring - Embedded Sensors PY - 2011 SN - 978-3-642-16640-2 SP - 932 EP - 949 PB - Springer CY - Berlin, Heidelberg AN - OPUS4-24180 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Skrotzki, Birgit A1 - Koch, B. T1 - Microstructural Characterization of the Metastable beta-titanium Alloy TIMETAL LCB after Fatigue Loading T2 - International Conference on Electron Nanoscopy and XXXII Annual Meeting of EMSI CY - Hyderabad, India DA - 2011-07-06 PY - 2011 AN - OPUS4-24181 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Isecke, Bernd A1 - Raupach, M. A1 - Eichler, Thorsten T1 - Time dependency of current and potential distribution during the cathodic protection of RC structures T2 - EUROCORR 2011 CY - Stockholm, Sweden DA - 2011-09-03 PY - 2011 AN - OPUS4-24182 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Merk, Virginia A1 - Kneipp, Janina T1 - Design and characterization of a new planar SERS sensor T2 - ECSBM CY - Coimbra, Portugal DA - 2011-08-29 PY - 2011 N1 - Geburtsname von Merk, Virginia: Joseph, V. - Birth name of Merk, Virginia: Joseph, V. AN - OPUS4-24183 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Drescher, Daniela A1 - Kneipp, Janina A1 - Matschulat, A. T1 - Biological multiplex applications of optical nanoprobes in live cells T2 - Tag der Chemie CY - Berlin, Germany DA - 2011-07-13 PY - 2011 AN - OPUS4-24184 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Drescher, Daniela A1 - Kneipp, Janina A1 - Matschulat, A. T1 - Biological multiplex applications of optical nanoprobes in live cells T2 - Tag der Chemie CY - Berlin, Germany DA - 2011-07-13 PY - 2011 AN - OPUS4-24185 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Drescher, Daniela A1 - Kneipp, Janina A1 - Orts Gil, Guillermo A1 - Natte, K. A1 - Laube, G. A1 - Österle, Werner T1 - Combining SERS and viablility tests for the investigation of nanotoxicity T2 - ESCBM - 14th European Conference on the Spectroscopy of Biological Molecules CY - Coimbra, Portugal DA - 2011-08-29 PY - 2011 AN - OPUS4-24186 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Drescher, Daniela A1 - Kneipp, Janina A1 - Laube, G. A1 - Guttmann, P. A1 - Schneider, G. T1 - Silver nanoparticles in cultured cells as viewed from a combined SERS, bioassy, and ultrastructural approach T2 - CellNanoSpec 2011 CY - Porquerolles, France DA - 2011-09-11 PY - 2011 AN - OPUS4-24187 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bussian, B A1 - Aichner, Bernhard A1 - Lehnik-Habrink, Petra A1 - Hein, Sebastian A1 - Nehls, Irene T1 - Monitoring organic pollutants in German forest soils T2 - Jahrestagung der Deutschen Bodenkundlichen Gesellschaft CY - Berlin, Germany DA - 2011-09-03 PY - 2011 AN - OPUS4-24188 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn A1 - Hertwig, Andreas A1 - Koter, Robert A1 - Weise, Matthias A1 - Beck, Uwe A1 - Reinstädt, Philipp A1 - Griepentrog, Michael A1 - Krüger, Jörg A1 - Picquart, M. A1 - Haro-Poniatowski, E. T1 - Analysis of femtosecond laser irradiation effects on amorphous hydrogenated hard carbon layers: Combining topometry, micro Raman spectroscopy and microsale mechanical indentation T2 - 11th International Conference on Laser Ablation (COLA 2011) CY - Playa del Carmen, Mexico DA - 2011-11-13 PY - 2011 AN - OPUS4-24189 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn A1 - Höhm, S. A1 - Rohloff, M. A1 - Rosenfeld, A. A1 - Krüger, Jörg T1 - Femtosecond laser-induced periodic surface structures: recent experimental and theoretical approaches T2 - 11th International Conference on Laser Ablation (COLA 2011) CY - Playa del Carmen, Mexico DA - 2011-11-13 PY - 2011 AN - OPUS4-24191 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberstein, M. A1 - Geier, M. A1 - Partsch, U. A1 - Völkel, L. A1 - Böhme, R. A1 - Pentzien, Simone A1 - Koter, Robert A1 - Mann, Guido A1 - Bonse, Jörn A1 - Krüger, Jörg T1 - Detailed study of laser doping processes for the selective emitter using phosphoric acid as dopant T2 - 3rd Workshop on Metallization for Crystalline Solar Cells CY - Charleroi, Belgium DA - 2011-10-25 PY - 2011 AN - OPUS4-24192 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Höhm, S. A1 - Bonse, Jörn A1 - Rohloff, M. A1 - Krüger, Jörg A1 - Rosenfeld, A. T1 - Dynamics of the formation of laser-induced periodic surface structures on dielectrics and semiconductors upon femtosecond laser pulse irradiation sequences T2 - 11th International Conference on Laser Ablation (COLA 2011) CY - Playa del Carmen, Mexico DA - 2011-11-13 PY - 2011 AN - OPUS4-24193 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlichting, Joachim A1 - Steinfurth, Henrik A1 - Maierhofer, Christiane A1 - Kreutzbruck, Marc T1 - Themorgrafische Prüfung von Schweißpunkten T2 - DGZfP-Jahrestagung CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24194 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian A1 - Basan, Ricardo T1 - Micromechanics Based Failure Analysis of Laminates under Off-axis Loading T2 - ICCM-18 - International Conference on Composite Materials CY - Jeju, South Korea DA - 2011-08-21 PY - 2011 AN - OPUS4-24195 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nie, Yaru A1 - Hübert, Thomas T1 - Surface silanization of carbon nanofillers for tailoring the properties of epoxy composites T2 - 9th meeting of the EUROFILLERS International Conference CY - Dresden, Germany DA - 2011-08-21 PY - 2011 AN - OPUS4-24196 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Darlatt, Erik A1 - Min, Hyegeun A1 - Poppenberg, J. A1 - Richter, S. A1 - Traulsen, C. H.-H. A1 - Schalley, C. A. A1 - Unger, Wolfgang T1 - ToF-SIMS study of the palladium(II) coordination on a pyridyl terminated self assembled monolayer T2 - SIMS XVIII CY - Riva del Garda, Italy DA - 2011-09-18 PY - 2011 AN - OPUS4-24197 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Noll, Matthias A1 - Weiler, Christiane A1 - Naumann, Annette A1 - Ifland, Andrea A1 - Appel, Bernd T1 - Listeria monocytogenes in raw milk and long-life milk biofilms T2 - COST Exploratory Workshop "Biofilms - Friend or Foe?" CY - Berlin, Germany DA - 2011-06-22 PY - 2011 AN - OPUS4-24218 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Peplinski, Burkhard A1 - Adamczyk, Burkart A1 - Adam, Christian A1 - Emmerling, Franziska T1 - Glimpses at individual reaction steps accompanying the crystallization of the tridmite form(s) of AIPO4 from an X-ray amorphous precipitate doped with potassium and magnesium T2 - Joint Meeting German Crystallographic Society (DKG), German Mineralogical Society (DMG) & Austrian Mineralogical Society (ÖMG) CY - Salzburg, Austria DA - 2011-09-20 PY - 2011 AN - OPUS4-24219 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sarfraz, Adnan A1 - Gnutzmann, Tanja A1 - Emmerling, Franziska A1 - Tremel, W. A1 - Dietzsch, M. T1 - Study of the crystallization of metal (IV) phosphonates: X-ray diffraction and thermal analysis T2 - Tag der Chemie CY - Berlin, Germany DA - 2011-07-13 PY - 2011 AN - OPUS4-24220 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhmert, L. A1 - Hansen, Ulf A1 - Girod, Matthias A1 - Niemann, B. A1 - Maul, Ronald A1 - Lampen, A. T1 - Der Einfluss eines vitro Verdaus auf die physikochemischen und toxikologischen Eigenschaften von Silbernanopartikeln T2 - 40. Deutscher Lebensmittelchemikertag CY - Halle (Saale), Germany DA - 2011-09-12 PY - 2011 AN - OPUS4-24221 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böhmert, L. A1 - Hansen, Ulf A1 - Girod, Matthias A1 - Lampen, A. A1 - Knappe, P. T1 - Cytotoxicity of AgPure silver nanoparticles in the human intestinal cell line Caco-2 T2 - Eurotox CY - Paris, France DA - 2011-08-28 PY - 2011 AN - OPUS4-24222 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Noll, Matthias A1 - Weiler, Christiane A1 - Ifland, Andrea A1 - Naumann, Annette A1 - Appel, Bernd T1 - Incorporation of Listeria monocytogenes in a raw milk and ultra heat treated milk-biofilm T2 - Gordon Research Conference on Applied & Environmental Microbiology CY - South Hadley, MA, USA DA - 2011-07-10 PY - 2011 AN - OPUS4-24223 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naumann, Annette A1 - Weiler, Christiane A1 - Ifland, Andrea A1 - Noll, Matthias T1 - Listeria monocytogenes in milk biofilms T2 - FT-IR Spectroscopy in Microbiological and Medical Diagnostics, Robert-Koch-Institut CY - Berlin, Germany DA - 2011-10-20 PY - 2011 AN - OPUS4-24225 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gnutzmann, Tanja A1 - Klimakow, Maria A1 - Rademann, K. A1 - Emmerling, Franziska T1 - In situ characterization of crystallization processes applying synchrotron XRD and Raman spectroscopy T2 - International School of Crystallography - 44th Course The Power of Powder Diffraction CY - Erice, Italy DA - 2011-06-02 PY - 2011 AN - OPUS4-24227 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühn, Julius A1 - Darlatt, Erik A1 - Poppenberg, J. A1 - Richter, S. A1 - Traulsen, C. H.-H. A1 - Schalley, C. A. A1 - Unger, Wolfgang T1 - Buried interface characterization for a click chemistry- derivatized self assembled monolayer on gold T2 - HAXPES 2011 CY - Hamburg, Germany DA - 2011-09-14 PY - 2011 AN - OPUS4-24198 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ferrero, Fabio A1 - Kluge, Martin A1 - Kreißig, Michael A1 - Schmidtchen, Ulrich A1 - Holtappels, Kai T1 - Prevention of the explosion of acetylene cylinders involved in fire: experiments and simulations T2 - ICDERS 2011 CY - Irvine, CA, USA DA - 2011-07-24 PY - 2011 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. AN - OPUS4-24199 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Molnarne, Maria A1 - Holtappels, Kai A1 - Wilrich, Cordula T1 - Chemically Unstable Gases and Gas Mixtures - New Categories in the GHS T2 - International Symposium Beyond Regulatory Compliance 2011, Making Safety Second Nature CY - College Station, TX, USA DA - 2011-10-25 PY - 2011 AN - OPUS4-24200 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Darlatt, Erik A1 - Poppenberg, J. A1 - Richter, S. A1 - Traulsen, C. H.-H. A1 - Schalley, C. A. A1 - Unger, Wolfgang T1 - Introduction of bulky donor head groups on a self assembled monolayer on gold exploiting click chemistry T2 - ECASIA 2011 CY - Cardiff, Wales DA - 2011-09-04 PY - 2011 AN - OPUS4-24201 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Darlatt, Erik T1 - Surface Chemical Analysis of immobilized Coordination Compounds based on Self assembled Monolayers on Gold T2 - ECASIA 2011 CY - Cardiff, Wales DA - 2011-09-04 PY - 2011 AN - OPUS4-24202 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Girard-Lauriault, Pierre-Luc A1 - Illgen, René A1 - Ruiz, J.-C. A1 - Wertheimer, M. R. A1 - Unger, Wolfgang T1 - Functionalization of graphite and carbon nanotube surfaces by vacuum-ultraviolet induced photochemical processes T2 - ECASIA '11 - 14th European Conference on Applications of surface and Interface Analysis CY - Cardiff, Wales DA - 2011-09-04 PY - 2011 AN - OPUS4-24203 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Straub, Franka T1 - Detection of Hydrogen in highly alloyed stainless steel microstructures by TOF-SIMS T2 - SIMS XVIII - 18th International Conference on Secondary Ion Mass Spectrometry CY - Riva del Garda, Italy DA - 2011-09-18 PY - 2011 AN - OPUS4-24204 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Straub, Franka A1 - Wirth, Thomas A1 - Unger, Wolfgang A1 - Böllinghaus, Thomas T1 - Detection of Hydrogen in highly alloyed stainless steel microstructures by TOF-SIMS T2 - ECASIA '11 - 14th European Conference on Applications of Surface and Interface Analysis CY - Cardiff, Wales DA - 2011-09-04 PY - 2011 AN - OPUS4-24205 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, M. A1 - Bonse, Jörn A1 - Schultz, C. A1 - Pahl, H.-U. A1 - Endert, H. A1 - Stannowski, B. A1 - Rau, B. A1 - Quaschning, V. A1 - Stegemann, B. T1 - Laser-Ablation Behavior of Thin-Film Materials used in Silicon and CIGSe based Solar Cells T2 - Eröffnungsveranstaltung PVComB - Kompetenzzentrum Dünnschicht- und Nanotechnologie für Photovoltaik Berlin CY - Berlin, Germany DA - 2011-03-30 PY - 2011 AN - OPUS4-24206 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, M. A1 - Bonse, Jörn A1 - Schultz, C. A1 - Pahl, H.-U. A1 - Endert, H. A1 - Rau, B. A1 - Stannowski, B. A1 - Quaschning, V. A1 - Stegemann, B. A1 - Fink, F. T1 - Single Wavelength Laser Processing for Monolithically Connected Si and CIGSe Thin Film Solar Cells T2 - Eröffnungsveranstaltung PVComB - Kompetenzzentrum Dünnschicht- und Nanotechnologie für Photovoltaik Berlin CY - Berlin, Germany DA - 2011-03-30 PY - 2011 AN - OPUS4-24207 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lühl, Lars A1 - Hahn, Oliver T1 - 3D Micro-XANES (X-Ray Absorption Near Edge Spectroscopy) T2 - Technart 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-24141 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Matthias A1 - Jann, Oliver T1 - Untersuchungen zur Entwicklung eines praxisnahen Messverfahrens für die Ermittlung der Radonexhalation aus Baumaterialien T2 - 18. WaBoLu-Innenraumtage - Energiesparlampen und andere Innenraumfragen CY - Berlin, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24143 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krug, Sonja A1 - Hahn, Oliver A1 - Homolka, M. A1 - Lang, A. A1 - Zimmer, J. T1 - Determination of Pesticides in Textiles with XRF T2 - TECHENART 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-24144 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lühl, Lars A1 - Mahlkow, S. A1 - Kanngießer, B. A1 - Alonpi, E. T1 - X-Ray Absorption Near Edge Spectroscopy at Attic Shards and their Replicas T2 - TECHNART 2011, Non-destructive and microanalytical techniques in art and cultural heritage CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-24145 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Torge, Manfred T1 - Klimamessungen an historischen Glasmalereien T2 - Abschlussveranstaltung des DBU-Evaluierungsprojektes CY - Stendal, Germany DA - 2011-06-08 PY - 2011 AN - OPUS4-24146 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lühl, Lars A1 - Hahn, Oliver A1 - Mantouvalou, I. A1 - Malzer, W. A1 - Kanngießer, B. T1 - 3D Micro-X-Ray Absorbtion Near Edge Spectroscopy T2 - EMRS Spring Meeting 2011 CY - Nice, France DA - 2011-05-09 PY - 2011 AN - OPUS4-24147 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Beyer, Katrin A1 - Kannengießer, Thomas A1 - Griesche, Axel A1 - Schillinger, B. T1 - Study of hydrogen effusion in austenitic stainless steel by time-resolved in-situ measurements using neutron radiography N2 - The purpose of the present study was to show the feasibility of measuring hydrogen effusion in austenitic stainless steel (1.4301) using neutron radiography at the facility ANTARES of the research reactor FRM II of the Technische Universität München. This method is appropriate to measure in-situ hydrogen effusion for hydrogen concentrations as small as 20 ppmH. Experiments were carried out in the temperature range from room temperature up to 533 K. The measurement principle is based on the parallel comparison of electrochemically hydrogen charged specimen with hydrogen-free reference specimen at the same temperature. This allows the determination of the hydrogen concentration in the specimens as a function of time and temperature. Separate hot carrier gas extraction experiments using the same temperature–time profiles as the radiography experiments have been used to calibrate the grey values of the neutron transmission images into hydrogen concentrations. It can be stated that the hydrogen effusion correlates with the specimen temperature. KW - Hydrogen effusion KW - Austenitic stainless steels KW - Neutron radiography PY - 2011 DO - https://doi.org/10.1016/j.nima.2011.02.010 SN - 0168-9002 SN - 0167-5087 VL - 651 IS - 1 SP - 211 EP - 215 PB - North-Holland CY - Amsterdam AN - OPUS4-23401 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kromm, Arne A1 - Kannengießer, Thomas T1 - Characterizing phase transformations of different LTT alloys and their effect on residual stresses and cold cracking N2 - Novel martensitic filler materials with specially adjusted martensite start temperatures (Ms) can counteract the cooling specific shrinkage due to expansion effects of the weld metal associated with phase transformations. That can be exploited to create compressive residual stresses in the weld and adjacent areas, i.e. beneficial for increasing fatigue strength. The Ms-temperature is shifted via the chemical composition, mainly by the alloying elements nickel and chromium, resulting as well in different retained austenite contents. Investigations were made using different Low Transformation Temperature (LTT) alloys with varying nickel content. The resulting phase transformation temperatures were — for the first time — detected using high energy synchrotron diffraction and Single Sensor Differential Thermal Analysis (SS-DTA). Compared to angle dispersive diffraction, energy dispersive diffraction offers the possibility to measure residual stresses of the martensite and austenite phase parallel fast in one experiment up to depths of 100 μm. The residual stresses show significant distributions dependent on the Ms-temperature. The effect on the cold cracking behaviour of these alloys was investigated using the Tekken test. Results show that cold cracking can be avoided when appropriate contents of retained austenite are existent. KW - Austenite KW - Cold cracking KW - Martensite KW - Low KW - Temperature KW - Transformation PY - 2011 SN - 0043-2288 SN - 1878-6669 VL - 55 IS - 03/04 SP - 48 EP - 56 PB - Springer CY - Oxford AN - OPUS4-23402 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubcová, Petra A1 - Rübner, Katrin T1 - Use of recycled construction waste and industrial waste materials in concrete N2 - Beside such well approved residues like fly ash, blast fumace slag, silica fume and crushed concrete orbrick, other materials, like waste incineration bottom ash, steel slag, biomass ash, industrial sludge or mixed demolition waste, bear the potential to be used in high-grade mineral building materials. However, sophisticated Processing technologies and progressive applications ofthe waste products are needed. The material efficiency has to be improved by further R&D activities. This paper Shows the activities ofthe working group “Saving Resources by Material Recycling” and presents research about the use of residues from industry, incineration processes and deconstruction for the production of high-grade mineral building materials. T2 - Recycling 2011 CY - Brno, Czech Republic DA - 17.03.2011 KW - Sekundärrohstoffe KW - Sekundäre Gesteinskörnung KW - Recycling KW - Leichtbeton PY - 2011 SN - 978-80-214-4253-5 SP - 87 EP - 92 AN - OPUS4-23403 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Quillard, S. A1 - Paris, M. A1 - Deniard, P. A1 - Gildenhaar, Renate A1 - Berger, Georg A1 - Obadia, L. A1 - Bouler, J.-M. T1 - Structural and spectroscopic characterization of a series of potassium- and/or sodium-substituted beta-tricalcium phosphate N2 - In this paper, we report X-ray diffraction investigations as well as Raman and solid-state 31P and 23Na magic angle spinning nuclear magnetic resonance (NMR) characterization of three series of calcium orthophosphates. The general formulae of the studied compounds are Ca10.5-x/2Mx(PO4)7, where M = K or Na and x = 0, 0.25, 0.50, 0.75, 1.0; and Ca10KxNa1-x(PO4)7, where x = 0, 0.25, 0.5, 0.75, 1.0. These calcium orthophosphates are found to be isostructural with β-tricalcium phosphate (β-TCP, Ca3(PO4)2) with the substitution of some calcium sites by potassium and/or sodium cations. The unit cell parameters vary continuously with the level of substitution, a characteristic of these solid solutions. The Raman spectra show the different vibrational bands of the phosphate groups PO4, while the NMR chemical shifts are sensitive to the non-equivalent phosphorus and sodium ions present in these substituted samples. As both Raman and NMR spectroscopies are local probes, they offer tools to distinguish between these different phosphorus and phosphate groups, according to their structural site and local environment, especially the type of cation substituent. A convenient decomposition of the Raman and NMR spectra into Gaussian–Lorentzian components leads us to propose an assignment of the main observed bands of these substituted β-TCPs. KW - Bioceramics KW - Tricalcium phosphate KW - X-ray diffraction KW - Raman spectroscopy KW - Solid-state NMR spectroscopy PY - 2011 DO - https://doi.org/10.1016/j.actbio.2010.12.016 SN - 1742-7061 VL - 7 IS - 4 SP - 1844 EP - 1852 PB - Elsevier CY - Amsterdam AN - OPUS4-23405 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schurig, Michael A1 - Klinger, Christian T1 - Vibration testing of indermediate bulk containers (IBC) for dangerous goods T2 - 25. IAPRI Symposium CY - Berlin, Germany DA - 2011-05-16 PY - 2011 AN - OPUS4-23406 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Simone A1 - Deubel, Jan A1 - Fettig, Ina A1 - Raspe, Tina A1 - Rothhardt, Monika T1 - Investigations on particles and smoke gas composition during smouldering of spruce wood T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23407 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krause, Christina A1 - Yin, Huajie A1 - Schönhals, Andreas T1 - Investigation of discotic liquid crystals T2 - DPG-Spring-Meeting 2011 CY - Dresden, Germany DA - 2011-03-13 PY - 2011 AN - OPUS4-23348 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mohamed, Alaa A1 - Mix, Renate A1 - Schönhals, Andreas A1 - Friedrich, Jörg F. T1 - Structure-Property Relationships of Thin Plasma Deposited Poly(acrylic acid) Films T2 - DPG-Spring-Meeting 2011 CY - Dresden, Germany DA - 2011-03-13 PY - 2011 AN - OPUS4-23349 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Rethmeier, Michael A1 - Schwenk, Christopher A1 - Heinze, Christoph T1 - Optimierung von Verzug und Eigenspannungen beim Schweißen dickwandiger Bauteile N2 - Die Schweißsimulation dickwandiger Bauteile stellt aufgrund der erhöhten Komplexität der thermophysikalischen und thermomechanischen Vorgänge beim Mehrlagenschweißen hohe Anforderungen an kommerziell verfügbare Schweißsimulationssoftware. Das umfasst die während des Fügeprozesses induzierten Verzüge und Eigenspannungen in das gefertigte Bauteil, welche zur Beurteilung der Fertigungsqualität von großer Bedeutung sind. Gerade in dickwandigen Bauteilen ist der Spannungszustand sowohl bedingt durch die konstruktive Steifigkeit der einzelnen Bauteile sowie der gesamten Baugruppe als auch aufgrund zusätzlicher externer Einspannvorrichtungen bei der Fertigung überaus komplex. Hinzu kommen bei Werkstoffen mit Phasenumwandlung noch die metallurgisch verursachten Spannungszustände und bei mehrlagig ausgeführten Schweißverbindungen die wiederholte thermische und umwandlungsbedingte Spannungsausbildung, so dass eine überschlägige Abschätzung des gesamten Verformungs- und Spannungszustandes auch für Experten in der Regel nicht mehr möglich ist. Die vorherrschenden Verformungen und Spannungen bestimmen jedoch maßgeblich die Eigenbeanspruchung der Schweißkonstruktion und damit deren Belastbarkeit im Betrieb. Eine genaue Kenntnis dieser Daten würde wertvolle Informationen zur Qualitätsoptimierung des Endproduktes liefern. KW - Schweißsimulation KW - Eigenspannungen KW - Verzug KW - Validierung KW - Sysweld KW - Mehrlagenschweißen PY - 2011 SN - 3-937567-98-4 SP - 1 EP - 160 PB - Verlag und Vertriebsgesellschaft mbH CY - Düsseldorf AN - OPUS4-23350 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schälike, Stefan A1 - Vela-Wallenschus, Iris A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. T1 - Vorhersage der thermischen Strahlung von KW-Poolfeuern mit CFD-Simulation T2 - Workshop Brandschutzforschung CY - Magdeburg, Deutschland DA - 2010-10-04 KW - Pool fire KW - Organic peroxides KW - TBPB KW - TBPEH KW - CFD KW - Safety distances PY - 2011 UR - http://www.vfdb.de/download/MagdeburgWorkshop2010/Schaelike_vfdb2010.pdf N1 - Geburtsname von Vela-Wallenschus, Iris: Vela, I. - Birth name of Vela-Wallenschus, Iris: Vela, I. SP - 1 EP - 25 AN - OPUS4-23352 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nooke, Alida A1 - Beck, Uwe A1 - Hertwig, Andreas A1 - Krause, Andreas A1 - Krüger, Hannes A1 - Lohse, Volkmar A1 - Negendank, Detlef A1 - Steinbach, J. T1 - Ellipsometric detection of gases with the surface plasmon resonance effect on gold top-coated with sensitive layers N2 - An ellipsometric gas sensor based on the surface Plasmon resonance (SPR) effect of ~ 43 nm thick gold layers was investigated. To protect the gold layer from contamination and to improve the detection limits, the gold layers were top-coated with 5–6 nm thick layers of organic a-C:H or with inorganic metal oxides TiO2 or ZrO2. The additional layers increased the long-term stability, whereas the metal oxide layers protect better than a-C:H. Furthermore, the additional layers decreased the detection limits by one order of magnitude in case of a-C:H and two orders of magnitude in case of the oxides. It could be shown that the detection limits also depend on the kind of preparation (sol–gel process or physical vapour deposition) of the additional layers. KW - Gas sensor KW - SPR KW - Ellipsometry KW - Sensitive layer KW - TiO2 KW - ZrO2 KW - a-C:H PY - 2011 DO - https://doi.org/10.1016/j.tsf.2010.11.091 SN - 0040-6090 VL - 519 IS - 9 SP - 2659 EP - 2663 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-23353 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Askar, Enis A1 - Baumeier, Andreas A1 - Holtappels, Kai A1 - Schröder, Volkmar A1 - Franzen, S. A1 - Büttgen, F. T1 - Explosionskenngrößen von Ethylenoxid und Ethylenoxid/Propylenoxid-Gemischen N2 - In Gasphasen aus Ethylenoxid (EO) und Propylenoxid (PO), die bei technischen Alkoxylierungsreaktionen vorkommen, können auch ohne den Zutritt von Luft Zerfallsreaktionen stattfinden, die explosionsartig mit einer vielfachen Temperatur- und Drucksteigerung verlaufen. Zur Abschätzung der Auswirkungen solcher Explosionen wurden die Explosionsdrücke und die zeitlichen Druckanstiege von reinem EO und EO/PO-Gemischen bei Temperaturen von 100°C bis 200°C und Drücken von 1 - 10 bar in einem 3-dm³-Behälter und punktuell in einem 100-dm³-Behälter experimentell bestimmt. KW - Explosionsdruck KW - Explosionsgrenzen KW - Explosionsschutz KW - Gase KW - Sicherheitstechnik KW - Explosion control KW - Explosion limits KW - Explosion pressure KW - Gases KW - Saftey engineering PY - 2011 DO - https://doi.org/10.1002/cite.201000099 SN - 0009-286X SN - 1522-2640 VL - 83 IS - 3 SP - 365 EP - 370 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-23354 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Heinze, Christoph A1 - Kromm, Arne A1 - Schwenk, Christopher A1 - Kannengießer, Thomas A1 - Rethmeier, Michael T1 - Welding residual stresses depending on solid-state transformation behaviour studied by numerical and experimental methods N2 - The development of high-strength structural steels with yield strengths up to 1000 MPa results in the requirement of suitable filler materials for welding. Recently designed low transformation temperature (LTT) alloys offer appropriate strength. The martensitic phase transformation during welding induces compressive residual stress in the weld zone. Therefore, the mechanical properties of welded joints can be improved. The present paper illustrates numerical simulation of the residual stresses in LTT-welds taking into account the effect of varying Ms/Mf-temperatures, and therefore different retained austenite contents, on the residual stresses. Residual stress distributions measured by synchrotron diffraction are taken as evaluation basis. A numerical model for the simulation of transformation affected welds is established and can be used for identification of appropriate Ms-temperatures considering the content of retained austenite. KW - Welding simulation KW - Residual stress KW - Low transformation temperature filler material KW - Martensitic transformation KW - Retained austenite PY - 2011 DO - https://doi.org/10.4028/www.scientific.net/MSF.681.85 SN - 0255-5476 VL - 681 SP - 85 EP - 90 PB - Trans Tech Publications CY - Aedermannsdorf, Switzerland AN - OPUS4-23357 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lischka, Susanne A1 - Nehls, Irene A1 - Piechotta, Christian T1 - 13C-markierte Kalibrierstandards für die Arsenspeziesanalytik mittels LC-ESI-MS/MS T2 - CANAS CY - Leipzig, Germany DA - 2011-03-13 PY - 2011 AN - OPUS4-23368 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kuhlich, Paul A1 - Piechotta, Christian A1 - Nehls, Irene T1 - Neue Desinfektionsnebenprodukte ausgewählter Personal Care Products T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23372 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Janzen, R. A1 - Sperling, M. A1 - Buscher, W. A1 - Bösel, A. A1 - Ehlbeck, J. A1 - Lischka, Susanne A1 - Piechotta, Christian T1 - Spezies-Analyse von Quecksilber-, Zinn- und Bleiverbindungen - Neues GC-MIP-OES-System N2 - Quecksilber-, Blei- und Zinnverbindungen gehören aufgrund Ihrer Toxizität zu den bedrohlichsten Umweltkontaminationen. Dabei können besonders die organischen Verbindungen bereits in kleinsten Mengen überaus schwerwiegende Folgen für Lebewesen verursachen. Während die anorganischen (mineralischen) Verbindungen dieser Elemente auch durch natürliche Prozesse wie Erosion aus Gestein und durch Vulkanismus in die Umwelt eingetragen werden, entstehen die meisten Kontaminationen der Umwelt aufgrund ihres jahrzehntelangen weltweiten Einsatzes in verschiedenen Pestiziden, Antifouling Anstrichen, Treibstoffen und zahlreichen industriellen Großprozessen, sowie ihrer Emission bei der Verfeuerung fossiler Brennstoffe. KW - GC-PED KW - Methylquecksilber KW - MIP PY - 2011 SN - 0016-3538 VL - 1 SP - 22 EP - 27 PB - GIT-Verlag CY - Darmstadt AN - OPUS4-23374 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wehrstedt, Klaus-Dieter T1 - Anwendung von Screening-Verfahren und Prüfmethoden zur Charakterisierung gefährlich exotherm zersetzlicher Stoffe T2 - 19. Ulm-Freiberger Kalorimetrietage CY - Freiberg, Germany DA - 2011-03-16 PY - 2011 AN - OPUS4-23375 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Poli, Marco A1 - Grätz, Rainer A1 - Schröder, Volkmar T1 - Limited applicability of gas explosion venting due to turbulence generation N2 - For the design of gas explosion venting systems for confinements only little guidance is given when considering the constructional boundary conditions or process conditions. For this reason conservative assumptions are prevalent in practice and in many cases the protective Systems become significantly oversized. Such safety margins in venting areas can lead to a critical acceleration of the pressure rise. Finally, a gas explosion at turbulent conditions caused by oversizing of the venting area rather leads to an under-sized system and supports the deflagration to detonation transition (DDT). The present investigation was focused especially on the influence of certain obstacles as well as the effect of the initial pressures on the explosion venting behavior of methane-air-mixtures and of hydrogen-air-mixtures. T2 - 2011 AIChE Spring meeting & 7th global congress on process safety CY - Chicago, IL, USA DA - 12.03.2011 KW - Gas explosion venting KW - Turbulent combustion KW - KG-value PY - 2011 IS - Topical 1 / #13 / 13h SP - 1 EP - 13 CY - New York, NY, USA AN - OPUS4-23376 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Deuerler, Frederike T1 - Comparsion of the notched impact strength at - 30 °C of polyethylene grades with the test performance behavior of packagings for the transport of dangerous goods N2 - The notched impact strength at -30 °C is one of the selected properties, together with the corresponding test method and tolerances, for a comparison of polyethylene grades of one design type in the procedural rule on suitability proof for alternative plastic resins used for packagings and intermediate bulk containers (IBCs) for the transport of dangerous goods. The marginal drop heights determined with the drop test at -18 °C after pre-storage of the test samples with 55 % nitric acid at 40 °C only partly related to the notched impact strength at -30 °C. The Charpy method is only suitable for classifying the grade in relation to toughness behavior and using this classification for comparison with other grades. Notched impact strength can provide a qualitative indication if the test samples fail under shock forces. Conditioning the design types with 55 % nitric acid for 21 days at 40 °C causes an increase in the marginal drop heights of the design types in drop tests at -18 °C when compared with design types without pre-storage. Post-crosslinking of the grades increases stiffness because of the acidic influence. T2 - NACE Konferenz CY - Houston, TX, USA DA - 13.03.2011 PY - 2011 AN - OPUS4-23377 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Ziegert, C. A1 - Dierks, K. A1 - Müller, Urs ED - Jäger, W. T1 - Lehmsteine und Lehmmörtel - Nachhaltige Bauprodukte auf dem Weg zur Stoffnorm N2 - Lehm ist ein seit Jahrtausenden bewährter, weit verbreiteter und heute ein moderner Baustoff. Für vordringliche Bauaufgaben in der Altbausanierung, dem energieeffizienten Neubau sowie dem Bauen in Entwicklungs- und Schwellenländern ist Lehm hervorragend geeignet. Der Baustoff Lehm ist zu einem Material für anspruchsvolle Bauvorhaben geworden. Seine Ästhetik und Ausstrahlung, seine Wirkung für Raumklima und Wohlbefinden werden von vielen Menschen geschätzt. Besonders zukunftsrelevant sind die umweltspezifischen Eigenschaften des Materials, z.B. die unerreichbar günstige Energiebilanz vieler Lehmbaustoffe. Lehmsteine werden im Neubau überwiegend für die Ausmauerung von Holzständerkonstruktionen verwendet (Bild 1). Die Anwendung für tragende Wände ist derzeit noch untergeordnet, gewinnt aber an Bedeutung. In der Altbausanierung und Denkmalpflege wird Lehm als historisch authentischer Baustoff und aufgrund seiner bauphysikalischen Qualitäten vielfältig eingesetzt. KW - Lehm KW - Normung KW - Prüfmethode PY - 2011 SN - 978-3-433-02956-5 DO - https://doi.org/10.1002/9783433600801.ch3 SN - 0170-4958 VL - 36 IS - Kap. III SP - 57 EP - 70 PB - Ernst & Sohn CY - Berlin AN - OPUS4-23328 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mehdianpour, Milad A1 - Schmid, Wolfgang A1 - Clobes, M. T1 - MOSYTRAF - Monitoringsystem zur Tragverhaltensstudie von Freileitungen unter Böenbeanspruchung N2 - MOSYTRAF steht für ein Monitoringsystem zur Tragverhaltensstudie von Freileitungen unter Böenbeanspruchung. Die Tragverhaltensstudie dient der Entwicklung eines realitätsnahen Berechnungsmodells zur Abschätzung der Mastbeanspruchung infolge Starkwindeinwirkung auf die Leiter. T2 - Messen im Bauwesen 2011 CY - Berlin, Germany DA - 01.03.2011 KW - Monitoring KW - Freileitungen KW - Wind KW - Naturmessung PY - 2011 SP - 89 EP - 100 AN - OPUS4-23331 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mermillod-Blondin, A. A1 - Mauclair, C. A1 - Rosenfeld, A. A1 - Bonse, Jörn A1 - Stoian, R. A1 - Audouard, E. T1 - Time-resolved imaging of bulk a-SiO2 upon various ultrashort excitation sequences N2 - Ultrashort pulses lasers are tools of choice for functionalizing the bulk of transparent materials. In particular, direct photoinscription of simple photonic functions have been demonstrated. Those elementary functions rely on the local refractive index change induced when focusing an ultrashort pulse in the volume of a transparent material. The range of possibilities offered by direct photoinscription is still under investigation. To help understanding, optimizing and assessing the full potential of this method, we developed a time-resolved phase contrast microscopy setup. The imaginary part (absorption) and the real part of the laser-induced complex refractive index can be visualized in the irradiated region. The setup is based on a commercially available phase contrast microscope extended into a pump-probe scheme. The originality of our approach is that the illumination is performed by using a pulsed laser source (i.e. a probe beam). Speckle-related issues are solved by employing adequate sets of diffusers. This laser-microscopy technique has a spatial resolution of 650 nm, and the impulse response is about 300 fs. The laser-induced refractive index changes can be tracked up to milliseconds after the energy deposition. The excitation beam (the pump) is focused with a microscope objective (numerical aperture of 0.45) into the bulk of an a-SiO2 sample. The pump beam can be temporally shaped with a SLM-based pulse shaping unit. This additional degree of flexibility allows for observing different interaction regimes. For instance, bulk material processing with femtosecond and picosecond duration pulses will be studied. T2 - Photonics West 2011 CY - San Francisco, CA, USA DA - 22.01.2011 PY - 2011 DO - https://doi.org/10.1117/12.876687 VL - 7925 IS - 79250R SP - 1 EP - 7 AN - OPUS4-23332 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger T1 - Wood Protection by Interfering with Insect Behavior - Adequacy of Laboratory Test Designs T2 - International Conference on Urban Pests CY - Ouro Preto, Brazil DA - 2011-08-08 PY - 2011 AN - OPUS4-23336 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger A1 - Herrmann, Bianca T1 - An attempt to reconstruct the natural and cultural history of the webbing clothes moth Tineola bisselliella (Lepidoptera: Tineidae) T2 - Meeting on Cultural Heritage Pests CY - Piacenza, Italy DA - 2011-06-07 PY - 2011 N1 - Geburtsname von Herrmann, Bianca: Krüger-Carstensen, B. - Birth name of Herrmann, Bianca: Krüger-Carstensen, B. AN - OPUS4-23337 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kautek, W. A1 - Grabner, G. A1 - Trautinger, F. A1 - Dexl, Alois K. A1 - Martin, Sven A1 - Mädebach, Heinrich A1 - Hertwig, Andreas A1 - Krüger, Jörg T1 - Femtosecond laser interaction with cornea and dermal tissues T2 - EMRS Spring Meeting 2001, Symposium J "Laser materials processing for micro and nano applications" CY - Nice, France DA - 2011-05-09 PY - 2011 AN - OPUS4-23378 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosenfeld, A. A1 - Höhm, S. A1 - Rohloff, M. A1 - Das, S. K. A1 - Krüger, Jörg A1 - Bonse, Jörn T1 - Formation of laser-induced periodic surface structures upon multiple irradiation sequences using double femtosecond laser pulses T2 - EMRS Spring Meeting 2011, Symposium J "Laser materials processing for micro and nano applications" CY - Nice, France DA - 2011-05-09 PY - 2011 AN - OPUS4-23379 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn A1 - Höhm, S. A1 - Rohloff, M. A1 - Rosenfeld, A. A1 - Krüger, Jörg T1 - Femtosecond laser-induced periodic surface structures on semiconductors and dielectrics T2 - EMRS Spring Meeting 2011, Symposium J "Laser materials processing for micro and nano applications" CY - Nice, France DA - 2011-05-09 PY - 2011 AN - OPUS4-23380 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krause, Ulrich A1 - Krüger, Simone A1 - Berger, Anka T1 - Bewertung von Brandgefahr und Rauchgastoxizität bei Recyclinglagern N2 - Brände bei der Lagerung von Deponiestoffen und Recyclingprodukten sind durch hohe Wärmefreisetzung und extreme Rauchentwicklung gekennzeichnet. Im Rauch enthalten sind in Abhängigkeit vom Ausgangsmaterial toxische oder gesundheitsgefährdende Stoffe. Löscharbeiten erfordern einen hohen Personal- und Materialaufwand und ziehen sich häufig über Tage, manchmal sogar über Wochen oder Monate hin. Der Schwerpunkt im Umgang mit solchen Materialien muss deshalb auf der Brandprävention liegen. Der vorliegende Beitrag stellt eine in der Bundesanstalt für Materialforschung und -prüfung (BAM) entwickelte Methodik vor, bei der in einer Kombination von Labortests und numerischen Simulationsrechnungen Haldengeometrien und zulässige Lagerungszeiten abgeleitet werden können, bei denen Selbstentzündung sicher vermieden wird. KW - Recycling KW - Selbstentzündung KW - Toxizität KW - Rauchgas PY - 2011 SN - 2191-0073 VL - 1 IS - 1/2 SP - 32 EP - 38 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-23381 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Körner, Ursula A1 - Neitsch, Marcel A1 - Wytrykus, Nancy A1 - Kiau, Torsten A1 - Schuster, Raimund T1 - Der schnelle Weg zur Anerkennung N2 - Verfahren - Das neue Schema zur Anerkennung von Qualitätssicherungsprogrammen erlaubt einen schnellen Zugriff auf die BAM-Homepage KW - Gefahrgut KW - Verpackung KW - IBC KW - Rekonditionierung KW - Reparatur KW - Regelmäßige Wartung KW - BAM-GGR 001 KW - Qualitätssicherungsprogramm PY - 2011 SN - 0944-6117 VL - 2 SP - 26 EP - 28 PB - Vogel CY - München AN - OPUS4-23385 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Deuerler, F. T1 - Comparison of the notched impact strength at -30°C of polyethylene grades with the test performance behavior of packagings for the transport of dangerous goods N2 - The notched impact strength at -30 °C is one of the selected properties, together with the corresponding test method and tolerances, for a comparison of polyethylene grades of one design type in the procedural rule on suitability proof for alternative plastic resins used for packagings and intermediate bulk containers (IBCs) for the transport of dangerous goods. The marginal drop heights determined with the drop test at -18 °C after pre-storage of the test samples with 55 % nitric acid at 40 °C only partly related to the notched impact strength at -30 °C. The Charpy method is only suitable for classifying the grade in relation to toughness behavior and using this classification for comparison with other grades. Notched impact strength can provide a qualitative indication if the test samples fail under shock forces. Conditioning the design types with 55 % nitric acid for 21 days at 40 °C causes an increase in the marginal drop heights of the design types in drop tests at -18 °C when compared with design types without pre-storage. Post-crosslinking of the grades increases stiffness because of the acidic influence. T2 - NACE International Corrosion Conference 2011 CY - Houston, TX, USA DA - 13.03.2011 KW - Dangerous goods packagings KW - Polyethylene grades KW - Notched impact strength at -30°C KW - Design type tests KW - Pre-storage with nitric acid PY - 2011 SP - 1 EP - 11 (Paper 11373) AN - OPUS4-23386 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häcker, Ralf A1 - Knothe, Esther A1 - Andrieux, F. A1 - Memhard, D. T1 - Entwicklung und Verifikation von Materialmodellen und numerischen Methoden zur Vorhersage der Containment Sicherheit beim Bersten von Laufrädern in Abgasturboladern (ATL) N2 - For predicting the Containment safety of turbochargers against failure of rotors at elevated temperatures and dynamic loading the complex deformation and damage behaviour of the respective materials has to be determined by appropriate experiments and on the other Hand the temperature and strain rate dependent data have to be implemented into material models that are able to describe the material behaviour underthese complex loading conditions. In this research project three different casting materials have been investigated. Since most experimental data were determined for the ductile cast iron alloy EN-GJS-400 with nodular graphite, this material was in the focus of numerical calcuiations. Its mechanical behaviour under uniaxial and multiaxial tension as well as under pressure and shear loading has been investigated for a variety of loading rates and temperatures. Since the material behaviour investigated in this project only concerns the Containment but not the rotor of the turbocharger the loading of the whole device was approached by impact loading of a plate with a projectile made of the same material. For the numerical modelling of the Containment safety of turbochargers a material model has been developed with the capability to describe the specific deformation behaviour of casting materials, e.g. different properties under tension and compression as a function of stress triaxiality, temperature and strain rate dependence under large plastic deformations. The material parameters for the model have been determined by numerical modelling of small scale tests under different loading conditions. The modei has been implemented in a commercial finite element code with explicit integration. In the actual Version of the user subroutine the application is limited to solid elements. In this project the material model has been applied to numerical simulations of tests on notched specimens under bending load and above all to the Simulation of penetration Tests under highly dynamic impact loading conditions as well as the Containment fest of a turbocharger. The loading conditions in these tests are comparable to the impact of a broken turbine blade on the Containment of a turbocharger. The main purpose of these tests hence was to prove the prediction capability of the material model. Numerical stability of the user routine could be achieved and the results agreed quite well with the experimental data. N2 - Für die Vorhersage der Containment Sicherheit beim Bersten von Laufrädern in Abgasturboladern müssen zum einen komplexe Verformungs- und Schädigungsvorgänge bei dynamischer Belastung einschließlich ihrer Temperaturabhängigkeit mit geeigneten Versuchen erfasst und gemessen werden, zum anderen müssen diese temperatur- und dehnratenabhängigen Kennwerte in weiterentwickelten Materialmodellen für das Verformungs- und Schädigungsverhalten abgebildet werden. Im Rahmen dieses Vorhabens wurden drei Gusswerkstoffe untersucht. Für den Gusswerkstoff mit Kugelgrafit EN-GJS-400 wurden die weitestgehenden experimentellen Untersuchungen zur Charakterisierung des Materialverhaltens unter ein- und mehrachsigem Zug sowie unter Druck- und Scherbeanspruchung für ein breites Spektrum von Beanspruchungsgeschwindigkeiten und Temperaturen durchgeführt. Die Untersuchungen an den beiden weiteren Werkstoffen erfolgten mit auf der Basis der gewonnen Erkenntnisse optimiertem Aufwand. Der Schwerpunkt der Arbeiten lag dabei im Bereich hoher Beanspruchungsgeschwindigkeiten und höherer Temperaturen sowie deren Kombination. Für die numerische Modellierung der Containment Sicherheit von ATLs wurde ein vorhandenes Materialmodell weiterentwickelt, so dass es in der Lage ist, das Verformungs- und Versagensverhalten von Gusswerkstoffen, wie z.B. den Zug-Druck-Unterschied, in Abhängigkeit von Spannungsmehrachsigkeit, Temperatur und Dehnrate auch für große plastische Deformationen zu beschreiben. Die Modellparameter wurden durch numerische Simulation von Experimenten an Proben bestimmt. Das Modell wurde in ein kommerzielles Finite-Elemente-Programm mit expliziter Integration implementiert und ist in der jetzigen Version auf FE-Modelle mit Volumenelementen beschränkt. Das Materialmodell wurde im Rahmen dieses Vorhabens zunächst zur numerischen Simulation von Experimenten an gekerbten Proben unter Biegebelastung angewendet. In einem zweiten Schritt erfolgte die Verifikation des Bauteilverhaltens durch numerische Simulation der hochdynamischen Beschussversuche. Da in diesem Vorhaben das Materialverhalten jedoch nur für das Containment und nicht auch für den Rotor des ATLs untersucht wurde, hat man für das Projektil und das Bauteil den gleichen Werkstoff verwendet. Die Belastung in diesen Beschussversuchen ist vergleichbar mit dem Aufprall eines Rotorfragments auf das Containment des Abgasturboladers. Abschließend wurde die numerische Simulation eines Containment Tests an einem Abgasturbolader durchgeführt. Die Nachrechnung dieser Experimente ist somit als ein Nachweis der Prognosefähigkeit des Materialmodells anzusehen. Numerische Stabilität der Userroutine konnte erreicht und eine gute Übereinstimmung mit den experimentellen Ergebnissen erzielt werden. T2 - Informationstagung Turbomaschinen, Frühjahrstagung 2011 CY - Bad Neuenahr, Germany DA - 17.03.2011 KW - Abgasturbolader KW - Containmentsicherheit PY - 2011 IS - R554 SP - 65 EP - 94 CY - Bad Neuenahr AN - OPUS4-23388 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heyn, Andreas T1 - Korrosionsschutz - Wechselwirkung zwischen Werkstoff, Medium und Design T2 - Anwendungsprofile von und durch AnSim - Galvanik neu gestalten CY - Berlin, Germany DA - 2011-03-23 PY - 2011 AN - OPUS4-23389 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heyn, Andreas T1 - Möglichkeiten zur Beschreibung des Schichtverhaltens unter Korrosionsaspekten T2 - Anwendungsprofile von und durch AnSim - Galvanik neu gestalten CY - Berlin, Germany DA - 2011-03-24 PY - 2011 AN - OPUS4-23390 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lange, Th. A1 - Liebner, Christian A1 - Hieronymus, Hartmut A1 - Heinrich, Sebastian A1 - Klemm, E. T1 - Untersuchung hetrogen katalysierter Selektivoxiationen im Explosionsbereich unter verwendung von Mikrostrukturreaktoren -Reaktionstechnische Untersuchungen- T2 - Jahrestreffen deutscher katalytiker mit Jahrestreffen Reaktionstechnik, 16. - 18. März 2011, Weimar CY - Weimar, Germany DA - 2011-03-16 PY - 2011 AN - OPUS4-23394 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Priebe, Nsesheye Susan T1 - Presentation of "Spearhead network for innovative, clean and safe cement and concrete technology" (SPIN) T2 - Workshop "Leichtbau und Spezialbauweisen für Afrika", BAM CY - Berlin, Germany DA - 2011-03-04 PY - 2011 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. AN - OPUS4-23395 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan A1 - Rübner, Katrin T1 - Saving resources by material recycling T2 - Workshop "Leichtbau und Spezialbauweisen für Afrika", BAM CY - Berlin, Germany DA - 2011-03-04 PY - 2011 AN - OPUS4-23396 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubcová, Petra A1 - Rübner, Katrin T1 - Use of recycled construction waste and industrial waste materials in Concrete T2 - Tagung Recycling 2011 CY - Brno, Czech Republic DA - 2011-03-17 PY - 2011 AN - OPUS4-23397 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Berger, Anka A1 - Michael-Schulz, Heike T1 - Untersuchungen zur thermischen Stabilität von Nitrocellulosefilmen T2 - 19. Ulm-Freiberger Kalorimetrietage CY - Freiberg, Germany DA - 2011-03-16 PY - 2011 AN - OPUS4-23359 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hertwig, Andreas A1 - Koter, Robert A1 - Bonse, Jörn A1 - Weise, Matthias A1 - Beck, Uwe A1 - Krüger, Jörg A1 - Picquart, M. A1 - Haro-Poniatowski, E. T1 - Blistering and layer modification of hydrogenated amorphous carbon layers induced by femtosecond laser pulse irration T2 - Bunsentagung 2011 CY - Berlin, Germany DA - 2011-06-02 PY - 2011 AN - OPUS4-23361 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Denkler, Tilman T1 - Technology transfer in the area of Quality Infrastructure N2 - - Definition of Quality Infrastructure - Tasks of BAM in the area of Quality Infrastructure - Project Support to SADC Member States in Standardization, Quality Assurance, Accreditation and Metrology (SQAM) T2 - Workshop "Lightweight and Special Construction for Africa" im Rahmen des Projektes "LightSHIP" CY - Berlin, Germany DA - 2011-03-04 PY - 2011 AN - OPUS4-23362 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yin, Huajie A1 - Schönhals, Andreas T1 - Glass Transition of Thin Poly(bisphenol A carbonate) Films Studied by Dielectric Spectroscopy T2 - DPG-Spring-Meeting 2011 CY - Dresden, Germany DA - 2011-03-13 PY - 2011 AN - OPUS4-23363 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubcová, Petra T1 - Innovative Leightweight Concrete with New Leightweight Aggregate Material T2 - Workshop "Leightweight and Special Constructions for Africa - Leichtbau und Spezialbauweisen für Afrika", BAM CY - Berlin, Germany DA - 2011-03-04 PY - 2011 AN - OPUS4-23364 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Poli, Marco A1 - Grätz, Rainer A1 - Schröder, Volkmar T1 - Limited Applicability of Gas Explosion Venting due to Turbulence Generation T2 - AIChe Spring Meeting 2011 und 7th Global Congress on Process Safety CY - Chicago, IL, USA DA - 2011-03-13 PY - 2011 AN - OPUS4-23366 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann, Jens A1 - Burkert, Andreas T1 - Nichtrostende Stähle im Bauwesen - Neue Ansätze zur Werkstoffauswahl Z-30.3-6 - Alternativen im Bereich Edelstahl Rostfrei T2 - Wissenschaft trifft Handwerk -Neue Werkstoffe und Verfahren auf der Baustelle CY - Leipzig, Germany DA - 2011-03-15 PY - 2011 AN - OPUS4-23367 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herrmann, Bianca A1 - Plarre, Rüdiger T1 - Out-door trapping and genetically characterization of populations of the webbing clothes moth Tineola bisselliella (Lepidoptera: Tineidae) in the broader area of Berlin T2 - Meeting on Cultural Heritage Pests CY - Piacenza, Italy DA - 2011-06-07 PY - 2011 N1 - Geburtsname von Herrmann, Bianca: Krüger-Carstensen, B. - Birth name of Herrmann, Bianca: Krüger-Carstensen, B. AN - OPUS4-23338 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weißhaupt, Petra A1 - Pritzkow, Wolfgang A1 - Noll, Matthias T1 - Nitrogen metabolism of wood decomposing basidiomycetes and their interaction with diazotrophs as revealed by IRMS T2 - Ecology of Soil Microorganisms - Koferenz der tschechischen Akademie der Wissenschaften CY - Prague, Czech Republic DA - 2011-04-27 PY - 2011 AN - OPUS4-23339 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Horbach, J. A1 - Meyer, A. T1 - Influence of thermodynamic forces on diffusion in melts N2 - We report about diffusion measurements and molecular dynamic simulations in Al-Ni and Al-Cu melts. Capillary methods were used to measure Ni and Cu self diffusion and to measure interdiffusion. The combination of the capillary set-up with X-ray radiography allowed in-situ detecting of convective contributions to the interdiffusion transport by tracking the time dependence of diffusion. Thus, the determination of the interdiffusion coefficient can be restricted to convection-free experiment times resulting in an increased accuracy of the measured interdiffusion coefficient. Additionally, quasielastic neutron scattering was used to measure convection-free Ni and Cu self diffusion. Molecular dynamics simulations were used to determine all diffusion coefficients and the thermodynamic factor. The comparison between experiment and simulation shows an excellent agreement of the interdiffusion coefficients as a function of temperature. It was found that interdiffusion is enhanced by thermodynamic forces with a maximum around the stoichiometric composition. T2 - TMS 2011 CY - San Diego, CA, USA DA - 2011-02-27 PY - 2011 AN - OPUS4-23340 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel T1 - Diffusion of hydrogen in steels T2 - DLR-Seminar CY - Cologne, Germany DA - 2011-02-15 PY - 2011 AN - OPUS4-23341 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rauchegger, Christian A1 - Schmidt, Dirk A1 - Lohse, Volkmar A1 - Schröder, Volkmar A1 - Thévenin, D. T1 - Experimentelle Untersuchungen zur Schwergasausbreitung T2 - ISUT Institutseminar CY - Magdeburg, Germany DA - 2011-01-18 PY - 2011 AN - OPUS4-23342 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dietrich, Paul A1 - Horlacher, T. A1 - Girard-Lauriault, Pierre-Luc A1 - Gross, Thomas A1 - Lippitz, Andreas A1 - Castelli, R. A1 - Min, Hyegeun A1 - Seeberger, P.H. A1 - Unger, Wolfgang T1 - Carbohydrate-functionalized surfaces: Analysis by an multi-method approach T2 - 5th Glycan Forum CY - Berlin, Germany DA - 2011-03-10 PY - 2011 AN - OPUS4-23344 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yin, Huajie A1 - Schönhals, Andreas T1 - Calorimetric Glass Transition of Thin Poly(bisphenol A carbonate) Films T2 - DPG-Spring-Meeting 2011 CY - Dresden, Germany DA - 2011-03-13 PY - 2011 AN - OPUS4-23345 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Purohit, Purv A1 - Schönhals, Andreas T1 - Structure-Property relationships of nanocomposites based on Polypropylene and Layered Double Hydroxide T2 - Deutsche Physikalische Gesellschaft (DPG), Spring Meeting 2011 CY - Dresden, Germany DA - 2011-03-13 PY - 2011 AN - OPUS4-23346 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Purohit, Purv A1 - Schönhals, Andreas T1 - Structure-Property relationships of nanocomposites based on Polyethylene and Layered Double Hydroxide T2 - Deutsche Pysikalische Gesellschaft (DPG) Spring Meeting 2011 CY - Dresden, Germany DA - 2011-03-13 PY - 2011 AN - OPUS4-23347 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Staude, Andreas A1 - Goebbels, Jürgen T1 - Determining the Spatial Resolution in Computed Tomography - Comparison of MTF and Line-Pair Structures T2 - International Symposium on Digital Industrial Radiology and Computed Tomography CY - Berlin, Germany DA - 2011-06-20 PY - 2011 AN - OPUS4-23229 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Staude, Andreas A1 - Goebbels, Jürgen T1 - Ortsauflösung in der Computertomographie - Vergleich von MTF und Linienpaarstrukturen T2 - DGZfP Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23230 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Staude, Andreas A1 - Goebbels, Jürgen A1 - Ritter, Z. A1 - Prohaska, S. A1 - Friedmann, A. A1 - Hege, H. C. A1 - Felsenberg, D. A1 - Brandt, R. T1 - Osteocytes number and volume in osteoporotic and in healthy bone biopsies analysed using Synchrotron CT: a pilot study T2 - ISB2011 XXIIIrd congress of the International Society of Biomechanics CY - Brussels, Belgium DA - 2011-07-03 PY - 2011 AN - OPUS4-23231 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meyer-Plath, Asmus A1 - Hoffschulz, H. A1 - Helbig, J. A1 - Schlüter, O. K. F. A1 - Wursche, R. T1 - CarbonNanotubes: Synthesis, Functionalization, Dispersion T2 - International Nanotechnology Exhibition and Conference Nano Tech 2011 CY - Tokyo, Japan DA - 2011-02-16 PY - 2011 AN - OPUS4-23233 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yang, Q.-C. A1 - Jochum, K. P. A1 - Stoll, B. A1 - Weis, U. A1 - Kuzmin, D. A1 - Wiedenbeck, M. A1 - Traub, Heike T1 - BAM-S005 Type A and B: New silicate reference glasses for microanalysis T2 - European Geosciences Union General Assembly 2011 CY - Vienna, Austria DA - 2011-04-03 PY - 2011 AN - OPUS4-23234 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Döring, Ingo T1 - Prüfverfahren, Tests und Kriterien T2 - Gefahr/gut Fachkonferenz "Lithiumbatterien" CY - Frankfurt am Main, Germany DA - 2011-02-15 PY - 2011 AN - OPUS4-23318 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maul, Ronald A1 - Mallwitz, F. A1 - Koch, Matthias A1 - Nehls, Irene T1 - Evaluierung und Validierung eines fluoreszenzpolarimetrischen Probenvorbereitungs- und Messverfahrens zur Mykotoxinanalyse T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23319 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maul, Ronald A1 - Sommerschuh, Katja A1 - Koch, Matthias A1 - Nehls, Irene T1 - Der Einfluss von Verdauenzymen auf die Bioverfügbarkeit von Mykotoxinen T2 - 48. Wissenschaftlicher Kongress der Deutschen Gesellschaft für Ernährung CY - Potsdam, Germany DA - 2011-03-16 PY - 2011 AN - OPUS4-23320 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koch, Matthias A1 - Köppen, Robert A1 - Proske, Matthias A1 - Nehls, Irene A1 - Riedel, Juliane T1 - cis-trans-Isomerie von Zearalenon - Unsicherheitsquelle in der Lebensmittelkontrolle? T2 - 40. Deutscher Lebensmittelchemikertag CY - Halle (Saale), Germany DA - 2011-09-12 PY - 2011 AN - OPUS4-23321 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppen, Robert A1 - Koch, Matthias A1 - Klein-Hartwig, Karin A1 - Nehls, Irene T1 - Qualitätssicherung in der Lebensmittelanalytik Referenzmaterial für T-2- und HT-2-Toxin T2 - 40. Deutscher Lebensmittelchemikertag 2011 CY - Halle (Saale), Germany DA - 2011-09-12 PY - 2011 AN - OPUS4-23322 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shcheglov, Pavel A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Study of welding plume during high power fiber laser welding T2 - Scientific Session NRNU "MEPhI" 2011 CY - Moscow, Russia DA - 2011-02-01 PY - 2011 AN - OPUS4-23323 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schwenk, Christopher A1 - Perret, William A1 - Thater, Raphael A1 - Heinze, Christoph T1 - Schweißsimulation an der BAM und am IPK T2 - Veranstaltung für Industrievertreter der Fa. ZF Friedrichshafen, Präsentation von aktuellen Projekten und Forschungsergebnissen CY - Friedrichshafen, Germany DA - 2011-02-22 PY - 2011 AN - OPUS4-23324 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mehdianpour, Milad A1 - Schmid, Wolfgang A1 - Clobes, M. T1 - MOSYTRAF - Monitoringsystem zur Tragverhaltensstudie von Freileitungen unter Böenbeanspruchung T2 - Messen im Bauwesen 2011 - Fachtagung, BAM CY - Berlin, Germany DA - 2011-03-01 PY - 2011 AN - OPUS4-23325 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scholz, Christian A1 - Spaltmann, Dirk A1 - Woydt, Mathias T1 - Highly concentrated and low friction slip-rolling contacts through thin film coatings and/or alternative steels? T2 - 38. Int. Conf. on Metallurgical Coatings and Thin Films (ICMCTF 2011) CY - San Diego, CA, USA DA - 2011-05-02 PY - 2011 AN - OPUS4-23326 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kromm, Arne A1 - Kannengießer, Thomas A1 - Altenkirch, J. A1 - Gibmeier, J. T1 - Residual stresses in multilayer welds with different martensitic transformation temperatures analyzed by high-energy synchrotron diffraction N2 - Low Transformation Temperature (LTT) alloys were developed in order to control the residual stress development by the martensitic phase transformation already during cooling of the weld metal. The positive effect of such LTT alloys on the mitigation of detrimental tensile residual stresses during welding has already been confirmed on the basis of individual laboratory tests. Within the current project it was experimentally investigated whether the phase transformation mechanisms are effective under increased restraint due to multi-pass welding of thicker specimens. The local residual stress depth distribution was analyzed non-destructively for V-type welds processed by arc welding using energy dispersive synchrotron X-ray diffraction (EDXRD). The use of high energy (20 keV to 150 keV) EDXRD allowed for the evaluation of diffraction spectra containing information of all contributing phases. As the investigated LTT alloy contains retained austenite after welding, this phase was also considered for stress analysis. The results show in particular how the constraining effect of increased thickness of the welded plates and additional deposited weld metal influences the level of the residual stresses in near weld surface areas. While the longitudinal residual stresses were reduced in general, in the transition zone from the weld to the heat-affected zone (HAZ) compressive residual stresses were found. KW - Low Transformation Temperature KW - Phase Transformation KW - Residual Stress KW - Synchrotron Diffraction PY - 2011 DO - https://doi.org/10.4028/www.scientific.net/MSF.681.37 SN - 0255-5476 VL - 681 SP - 37 EP - 42 PB - Trans Tech Publications CY - Aedermannsdorf, Switzerland AN - OPUS4-23470 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Maierhofer, Christiane A1 - Mecke, R. A1 - Meinhardt, J. ED - Jäger, W. T1 - Instandsetzung und Ertüchtigung von Mauerwerk, Teil 8: Bewertung von Schädigungsprozessen mithilfe zerstörungsfreier Prüfverfahren N2 - Schäden an Bauwerksoberflächen wie Risse, Ablösungen, Feuchte, Bewuchs (Moose, Flechten, Pilze usw.) und Krustenbildung werden zurzeit hauptsächlich durch konventionelle Verfahren, wie z.B. Sichtprüfung und manuelle Vermessung, erfasst. Zur Sicherung des kulturellen Erbes werden jedoch dringend moderne und effiziente Verfahren und Strategien für eine vorbeugende Instandhaltung benötigt, die mit geringeren Kosten häufigere Inspektionen ermöglichen. Auch Wachstum und Alterung des Gebäudebestands verschärfen die Situation zunehmend, Da eine detaillierte 3-D-Darstellung und wiederholte Beobachtung insbesondere von Rissen und Ablösungen u.a. auch für die sicherheitsrelevante Einschätzung der Standsicherheit eines Gebäudes eine sehr große Rolle spielen, wurden in den letzten Jahren laserbasierte Messverfahren weiterentwickelt und eingesetzt, Diese ermöglichen eine schnelle und automatisierte Erfassung der Oberflächengeometrie und können zudem innerhalb vorgegebener Zeitintervalle wiederholt eingesetzt werden. Das Verfahren kann auch durch eine zusätzliche Aufnahmetechnik ergänzt werden, die eine Zuordnung von erfassten Farbwerten zu den 3-D-Messpunkten erlaubt. KW - Aktive Thermografie KW - 3D Laserscanner KW - Historisches Mauerwerk KW - Monitoring KW - Datenfusion PY - 2011 SN - 978-3-433-02956-5 SN - 0170-4958 VL - 36 IS - Kap. III SP - 337 EP - 350 PB - Ernst & Sohn CY - Berlin AN - OPUS4-23471 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfennig, A. A1 - Linke, B. A1 - Schulz, Sabrina A1 - Kranzmann, Axel T1 - CO2-corrosion of steels exposed to saline water environment N2 - With CO2 being one reason for climate change carbon capture and storage (CCS) is discussed to mitigate climate change. When emission gases are compressed into deep geological layers CO2-corrosion can easily cause failure of injection pipes. Different steels 42CrMo4, X46Cr13 and X20Cr13 were tested as well as X35CrMo17 and X5CrNiCuNb16-4 in a laboratory Environment similar to the conditions of the CCS engineering site at the Northern German Bassin. Samples were exposed to synthetic aquifer water saturated with technical CO2 at a flow rate of 3 NL/h. Corrosion rates obtained via mass loss vary in a wide range (0,005 to 2.5 mm/year). The precipitations within the corrosion scale revealed a complicated multiphase layer containing siderite FeCO3, goethite α-FeOOH, lepidocrocite γ-FeOOH, mackinawite FeS and akaganeite Fe8O8(OH)8Cl1,34 and spinelphases of various compositions. T2 - TMS 2011 - 140th Annual Meeting & Exhibition CY - San Diego, CA, USA DA - 27.02.2011 KW - CCS KW - Steel KW - Corrosion KW - Carbon Capture and Storage PY - 2011 DO - https://doi.org/10.1002/9781118062173.ch102 VL - 3 IS - 0807 SP - 807 EP - 814 AN - OPUS4-23472 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bothe, Martin A1 - Binte Gose, H. A1 - Yi Mya, K. A1 - He, Ch. A1 - Pretsch, Thorsten T1 - Dual-Shape Memory Effect in SPOSS-PU T2 - Synthesis and Integration Group Seminar, Institute of Materials Research and Engineering (IMRE) CY - Singapore DA - 2011-02-23 PY - 2011 AN - OPUS4-23473 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker ED - Ziegahn, K.-F. T1 - Lebensdauerabschätzungen für Polypropylen durch Dosis-Wirkungsfunktionen bezüglich Bestrahlungsstärke und Temperatur (ViPQuali-Projekt) N2 - Für Polypropylen unterschiedlicher Stabilisierung wurden in künstlichen Bestrahlungstests sowohl die spektrale Empfindlichkeit als auch die Temperaturabhängigkeit der Rissbildung quantitativ ermittelt. Dafür wurde die Dauer bis zur Rissbildung sowohl bei spektraler Bestrahlung als auch bei Bestrahlung in einem UV-Leuchtstofflampengerät bei verschiedenen Temperaturen bestimmt. Die Temperaturabhängigkeit konnte als Arrhenius-Abhängigkeit beschrieben werden; das Wirkungsspektrum wurde an eine Stufenfunktion angepasst. Anschließend wurde auch noch der Einfluss des Stabilisatorgehalts als Potenzfit parametrisiert. Die Einzelabhängigkeiten wurden zu einer Gesamtfunktion der Wirkungen in Abhängigkeit der Dosis zusammengesetzt, die es ermöglicht die Wirkungen unterschiedlicher Dosiskombinationen abzuschätzen. Zur Validierung der Dosis-Wirkungsfunktionen wurden Freibewitterungsergebnisse aus Phoenix/Arizona herangezogen. Mit der Dosis, die sich aus den Wetterdaten dieser Freibewitterung ergibt, wurden anhand der Dosis-Wirkungs-Funktionen die jeweiligen Lebensdauern errechnet und mit dem experimentell bestimmten Versagen in der Freibewitterung verglichen. Die Arbeiten erfolgten im Rahmen des ViPQuali-Projektes mit dem Ziel der Bestimmung der Materialkenngrößen. T2 - 40. Jahrestagung der GUS 2011 - Umwelteinflüsse erfassen, simulieren, bewerten CY - Stutensee-Blankenloch/Karlsruhe, Germany DA - 30.03.2011 KW - Bewitterung KW - UV KW - Lebensdauer KW - Simulation KW - Polypropylen PY - 2011 SN - 978-3-9813136-1-1 IS - V17 SP - 227 EP - 237 PB - DWS Werbeagentur und Verlag GmbH CY - Karlsruhe AN - OPUS4-23474 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scholz, G. A1 - Krahl, Thoralf A1 - Ahrens, M. A1 - Martineau, C. A1 - Buzaré, J.Y. A1 - Jäger, Christian A1 - Kemnitz, E. T1 - 115In and 19F MAS NMR study of (NH4)3InF6 phases N2 - This study presents for the first time an NMR spectroscopic characterization of the room and high temperature phases of (NH4)3InF6 using 19F and 115In as probe nuclei. The reversible phase transition to the cubic phase at 353 K was followed by MAS NMR in situ. Static NMR experiments of the room temperature phase and MAS NMR experiments of the high temperature phase allowed the determination of the NMR parameters of both nuclei. Finally, the scalar In–F coupling, rarely observed in solid state NMR, is evidenced in both room and high temperature phases of (NH4)3InF6, and measured in the high temperature phase. KW - (NH4)3InF6 KW - 115In and 19F solid state NMR KW - XRD PY - 2011 DO - https://doi.org/10.1016/j.jfluchem.2011.01.010 SN - 0022-1139 SN - 1873-3328 VL - 132 IS - 4 SP - 244 EP - 249 PB - Elsevier CY - Amsterdam AN - OPUS4-23475 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Westin, E. M. A1 - Stelling, Karen A1 - Gumenyuk, Andrey T1 - Single-pass laser-GMA hybrid welding of 13.5 mm thick duplex stainless steel N2 - Single-pass solid-state laser welding of plates in the thickness range of 10 to 20 mm became possible with the invention of the fibre laser. This new technique provides excellent beam quality at powers as high as 20 kW or more, and has proved applicable in several industrial applications. By replacing conventional methods with the fibre laser, it is possible to avoid multiple-pass welding that requires time-consuming bevelling. The high energy density of the fibre laser beam also reduces the heat input and consequently the distortion. However, the rapid solidification and cooling associated with laser welding can cause imbalance of the microstructure of duplex stainless steel weldments, where excessively high ferrite contents may reduce the corrosion resistance and the ductility of the material. The solution is normally to add nickel-based filler wire and to increase the heat input. By using a hybrid welding process where the laser beam and the gas metal arc (GMA) process act in a common process zone, filler metal can be added to the molten pool at higher heat input and at the same time, higher welding speed and deeper penetration can be achieved. In this work, 13.5 mm thick 2205 (EN 1.4462, UNS S31803) was fibre laser-GMA hybrid welded in a single-pass using 14 kW of laser power and ISO 22 9 3 N L as filler wire for the GMA process. The resulting welds were free from defects, with smooth surfaces and full penetration. The investigation examines the weld metal microstructure and the effect on corrosion resistance and mechanical properties. The option to add nickel foil, when hybrid welding, was also investigated, as comparison, and the effect on austenite formation was evaluated. KW - Austenite KW - Combined processes KW - Corrosion KW - Duplex stainless steels KW - Laser welding KW - Microanalysis KW - Weld metal KW - Weldability KW - Welding PY - 2011 SN - 0043-2288 SN - 1878-6669 VL - 55 IS - 1/2 / IIW-2028-09 SP - 39 EP - 49 PB - Springer CY - Oxford AN - OPUS4-23476 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jakubcová, Petra A1 - Rübner, Katrin T1 - Alte Mauern für neuen Beton - Blähgranulate: eine neue, leichte Gesteinkörnung aus Bau- und Abbruchabfällen N2 - Materialien wie Mauerwerkbruch eignen sich als Rohstoffe zur Herstellung hochwertiger leichter Gesteinskörnungen. Aus Mauerwerkbruch hergestellte Blähgranulate können natürlichen Blähton ersetzen. Leichtbetone mit Blähgranulaten als Zuschlag zeigen ähnliche Eigenschaften wie solche mit herkömmlichen Blähtönen gleicher Roh- und Schüttdichte. KW - Sekündärrohstoffe KW - Sekundäre Gesteinskörnung KW - Recycling KW - Leichtbeton PY - 2011 SN - 0014-7699 VL - 117 IS - 4 SP - 124 EP - 127 PB - Vincentz CY - Hannover AN - OPUS4-23477 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fahmy, A. A1 - Mix, Renate A1 - Schönhals, Andreas A1 - Friedrich, Jörg Florian T1 - Structure of plasma-deposited poly(acrylic acid) films N2 - Poly(acrylic acid) films with a thickness of about 150?nm were deposited using a pulsed plasma onto aluminum and glass. The structure/property relationships of these samples were studied in dependence to the duty cycle (DC) of the plasma by a broad combination of different techniques and probes. For the first time, volume sensitive methods (FTIR, dielectric spectroscopy, and differential scanning calorimetry) are combined with surface analyses i.e. XPS. For an unambiguous identification of COOH groups by XPS, derivatization with trifluoroethanol was accomplished. Quantitative FTIR investigations give qualitatively a dependence of the concentration of COOH groups upon DC similar to that given by XPS investigations. The observed differences are discussed considering the different analytical depths of both methods. The dielectric measurements reveal that the structure of the plasma deposited films is different from that of the bulk material. Moreover, these measurements show also that the plasma deposited films are not thermally stable but undergo a post plasma chemical reaction during heating, where the reaction kinetics depends on DC. PY - 2011 DO - https://doi.org/10.1002/ppap.201000108 SN - 1612-8850 SN - 1612-8869 VL - 8 IS - 2 SP - 147 EP - 159 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-23478 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mya, K.Y. A1 - Gose, H.B. A1 - Pretsch, Thorsten A1 - Bothe, Martin A1 - He, C. T1 - Star-shaped POSS-polycaprolactone polyurethanes and their shape memory performance N2 - Star-shaped polyhedral oligomeric silsesquioxane (SPOSS)-based multi-arm poly(ε-caprolactones) (PCLs) with various arm lengths were synthesized by ring opening polymerization of ε-caprolactone. Increasing the PCL arm lengths was observed to increase the melting temperature and also the melt crystallization temperature in SPOSS-PCLs. Star-shaped POSS-PCL polyurethanes (SPOSS-PUs) were then prepared by cross-linking SPOSS-PCLs with hexamethylene diisocyanate (HMDI) and their shape memory (SM) behaviour was determined. For this purpose two cyclic thermo-mechanical testing concepts with similar programming (deformation and shape fixing) but different recovery strategies (free strain versus fixed-strain constrained stress recovery) were used and the synthesized polymers were systematically investigated around the crystallization and melting temperatures of PCL. SPOSS-PU with the highest POSS content exhibited remarkable cycles-averaged (N = 2–5) shape fixities and strain recoverabilities of 98% and stress recoverabilities close to 100%. The main structural factors that were expected to reduce the SM performances with increasing PCL arm lengths were a lowering of cross-link density (content of octasubstituted POSS) and an increase in chain flexibility/molecular mobility. KW - Shape memory polymer KW - Active polymer KW - Hybrid star-shaped polymer KW - POSS-polycaprolactone polyurethanes KW - Thermo-mechanical properties PY - 2011 DO - https://doi.org/10.1039/c0jm04459h SN - 0959-9428 SN - 1364-5501 VL - 21 IS - 13 SP - 4827 EP - 4836 PB - Royal Society of Chemistry CY - Cambridge AN - OPUS4-23479 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ros-Lis, J.V. A1 - Martínez-Mánez, Ramon A1 - Soto, J. A1 - Villaescusa, L.A. A1 - Rurack, Knut T1 - Squaraine 'ships' in the Y zeolite 'bottle': a chromogenic sensing material for the detection of volatile amines and thiols N2 - The inclusion of squaraine (SQ) dye I into the supercages of zeolite Y (structure code FAU) with a SiO2/Al2O3 ratio of 30 (Z30) through a two-step ship-in-the-bottle approach is reported, resulting in the squaraine-containing hybrid material Z30-SQ. Attempts to use the same synthetic procedure on sodium and ammonium Y zeolites were unsuccessful, stressing the importance of the presence of Brønsted acid centres in the Z30 zeolite. The reflectance spectra of Z30-SQ show a maximum in the typical squaraine monomer region at 618 nm and a shoulder at 570 nm. Spectral analyses revealed that the major species are SQ dimers and (tightly adsorbed) SQ monomers and SQ aggregates are only formed to a minor degree. The emission spectrum of Z30-SQ shows a single band at 669 nm. The sensory performance of this material was tested in the presence of volatile propylamine and propylthiol and other volatile organic compounds (acetone, ethanol, dichloromethane, hexane, acetonitrile, ethyl acetate, ethyl ether and acetic acid). The blue Z30-SQ material reacts with the thiol and amine derivatives, resulting in the bleaching of the solid and disappearance of the absorption band in the visible region, but does not undergo spectroscopic changes in the presence of other volatile organic compounds (VOCs). Whereas the reaction with propylamine is irreversible, a partial reversibility was found in the presence of the thiol. Theoretical investigations of the reactivity of I with several VOC molecules at the semi-empirical level reproduced well the experimentally observed reactivity. KW - Fluoreszenz KW - Gassensorik KW - Squarain-Farbstoffe KW - Zeolite PY - 2011 DO - https://doi.org/10.1039/c0jm03780j SN - 0959-9428 SN - 1364-5501 VL - 21 IS - 13 SP - 5004 EP - 5010 PB - Royal Society of Chemistry CY - Cambridge AN - OPUS4-23480 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rurack, Knut A1 - Spieles, Monika T1 - Fluorescence quantum yields of a series of red and near-infrared dyes emitting at 600-1000 nm N2 - The determination of the fluorescence quantum yields (QY, Φf) of a series of fluorescent dyes that span the absorption/excitation and emission ranges of 520-900 and 600-1000 nm is reported. The dyes encompass commercially available rhodamine 101 (Rh-101, Φf = 0.913), cresyl violet (0.578), oxazine 170 (0.579), oxazine 1 (0.141), cryptocyanine (0.012), HITCI (0.283), IR-125 (0.132), IR-140 (0.167), and four noncommercial cyanine dyes with specific spectroscopic features, all of them in dilute ethanol solution. The QYs have been measured relative to the National Institute of Standards and Technology's standard reference material (SRM) 936a (quinine sulfate, QS) on a traceably characterized fluorometer, employing a chain of transfer standard dyes that include coumarin 102 (Φf = 0.764), coumarin 153 (0.544), and DCM (0.435) as links between QS and Rh-101. The QY of Rh-101 has also been verified in direct measurements against QS using two approaches that rely only on instrument correction. In addition, the effects of temperature and the presence of oxygen on the fluorescence quantum yield of Rh-101 have been assessed. KW - Farbstoffe KW - Fluoreszenz KW - Nahes Infrarot KW - Quantenausbeute PY - 2011 DO - https://doi.org/10.1021/ac101329h SN - 0003-2700 SN - 1520-6882 VL - 83 IS - 4 SP - 1232 EP - 1242 PB - American Chemical Society CY - Washington, DC AN - OPUS4-23481 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Wolff, Dietmar T1 - Safety Aspects of Long Dry Interim Storage of Spent Fuel in Germany T2 - International High-Level Radioactive Waste Managment Conference CY - Albuquerque, NM, USA DA - 2011-04-10 PY - 2011 AN - OPUS4-23483 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heunisch, Andreas A1 - Schulz, Bärbel A1 - Rabe, Torsten A1 - Gaebler, A. A1 - Strunck, S. T1 - Fabrication and Characterisation of LTCC multilayer with large embedded cavities T2 - Konferenz der European Ceramic Society CY - Stockholm, Sweden DA - 2011-06-19 PY - 2011 AN - OPUS4-23485 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kuchenbecker, Petra A1 - Gemeinert, Marion A1 - Rabe, Torsten T1 - Ergebnisse eines Ringversuchs zur Bestimmung der Partikelgrößenverteilung von Feinstpulvern mittels Laserstreulichtverfahren T2 - DKG-Jahrestagung 2011 CY - Saarbrücken, Germany DA - 2011-03-28 PY - 2011 AN - OPUS4-23486 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabe, Torsten T1 - Die Bedeutung der Sinteratmosphäre in der HTCC- und LTCC-Multilayerfertigung T2 - DKG-Jahrestagung 2011 CY - Saarbrücken, Germany DA - 2011-03-28 PY - 2011 AN - OPUS4-23487 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Qiao, Linan A1 - Zencker, Uwe A1 - Musolff, André A1 - Komann, Steffen T1 - Dynamic Finite Element Analyses of a Spent Fuel Transport and Storage Cask with Impact Limiters by 9 meter Drop tests T2 - 2011 SIMULIA Customer Conference CY - Barcelona, Spain DA - 2011-05-17 PY - 2011 AN - OPUS4-23458 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna T1 - Mikrobiologische Perspektiven der Materialkunde T2 - Fraunhofer-Kolloquium am Fraunhofer-Institut für Werkstoffmechanik IWM CY - Halle (Saale), Germany DA - 2011-03-22 PY - 2011 AN - OPUS4-23459 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wehrstedt, Klaus-Dieter T1 - Identifizierung gefährlich exotherm zersetzlicher Stoffe T2 - DECHEMA-Weiterbildungskurs "Sicherheit chemischer Reaktionen", BAM CY - Berlin, Germany DA - 2011-03-28 PY - 2011 AN - OPUS4-23461 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian T1 - Strength of Composite Structural Parts - Role of Fiber/Matrix Interface T2 - SAMPE-SEICO Conference CY - Paris, France DA - 2011-03-28 PY - 2011 AN - OPUS4-23462 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taffe, Alexander T1 - Unsicherheit quantitativer zerstörungsfreier Prüfverfahren: Laufzeitmessung zur Bauteil-Dickenbestimung T2 - 260. PTB-Seminar, Berechnung der Messunsicherheit - Empfehlungen für die Praxis CY - Berlin, Germany DA - 2011-03-21 PY - 2011 AN - OPUS4-23463 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taffe, Alexander T1 - Zuverlässige Bewehrungsortung: Vom klassischen Handgerät zum automatisierten Scannersystem T2 - Niedersächsische Landesbehörde für Straßenbau und Verkehr CY - Hanover, Germany DA - 2011-03-28 PY - 2011 AN - OPUS4-23464 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Larissa A1 - Jakubowski, Norbert A1 - Roos, P.H. T1 - Multi-parametric analysis of cytochrome P450 expression in rat liver microsomes by LA-ICP-MS N2 - Quantitative analysis of cytochrome P450 (CYP) patterns of cells and tissues is an important aspect in toxicological and pharmacological research as this group of enzymes is largely involved in the metabolism of toxic compounds and drugs. Here we present a method for the multi-parametric and simultaneous quantitative determination of several cytochromes P450 in liver microsomes of untreated and inducer treated rats. The method is based on the binding of specifically lanthanide labelled antibodies to electrophoretically separated and blotted CYP proteins and their subsequent identification and quantification by LA-ICP-MS. CYP1A1, CYP2B1, CYP2C11, CYP2E1 and CYP3A1 were simultaneously quantified and the patterns between microsomal samples were compared. Microsomes of rats treated with 3-methylcholanthrene, phenobarbital and dexamethasone showed increased levels of CYP1A1, CYP2B1 and CYP3A1, respectively. These results coincide with data obtained by independent methods for CYP quantification, i.e. ethoxyresorufin O-deethylase activity for CYP1A1 and pentoxyresorufin O-depentylase for CYP2B1. The presented method is useful for multi-parametric CYP profiling and has further large potential with respect to the number of analysed parameters/proteins and sensitivity. PY - 2011 DO - https://doi.org/10.1039/c0ja00077a SN - 0267-9477 SN - 1364-5544 N1 - Geburtsname von Müller, Larissa: Wäntig, L. - Birth name of Müller, Larissa: Wäntig, L. VL - 26 IS - 2 SP - 310 EP - 319 PB - Royal Society of Chemistry CY - London AN - OPUS4-23465 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jakubowski, Norbert A1 - Prohaska, T. A1 - Rottmann, L. A1 - Vanhaecke, F. T1 - Inductively coupled plasma- and glow discharge plasma-sector field mass spectrometry - Part I. Tutorial: Fundamentals and instrumentation N2 - The aim of this series of two reviews is to introduce the basic concepts of ICP and GD sector field instruments, to discuss their peculiarities and performance, to present selected analytical applications for demonstration of the 'state of the art' and, finally, to identify possible future trends and developments. Part I focuses on fundamentals, instrumentation and operation of instruments to give an overview of the capabilities of the actual commercially available instrumentation, whereas selected applications will be discussed in detail in part II. PY - 2011 DO - https://doi.org/10.1039/c0ja00161a SN - 0267-9477 SN - 1364-5544 VL - 26 IS - 4 SP - 693 EP - 726 PB - Royal Society of Chemistry CY - London AN - OPUS4-23466 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jakubowski, Norbert T1 - Inductively coupled plasma- and glow discharge plasma-sector field mass spectrometry - Part II. Applications N2 - Part I of this series of two reviews focused on fundamentals, instrumentation and operation of sector field instruments to give a proper overview of the capabilities of the actual commercially available instrumentation. In part II, selected applications of the last decade are discussed in detail concluding with pinpointing possible future trends and current developments. KW - ICP KW - SF KW - MS PY - 2011 DO - https://doi.org/10.1039/c0ja00007h SN - 0267-9477 SN - 1364-5544 VL - 26 IS - 4 SP - 727 EP - 757 PB - Royal Society of Chemistry CY - London AN - OPUS4-23467 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wosniok, Aleksander A1 - Krywult, L. A1 - Liehr, Sascha A1 - Krebber, Katerina A1 - Wendt, Mario A1 - Chrost, A. T1 - Monitoring konstrukcji ziemnych przy zastosowaniu rozlozonych przestrzennie swiatlowodowych sensorów optycznych, zintegrowanych w geosyntetykach KW - Fibre optic sensor KW - Spatial distributed sensor KW - Polymer optical fibre (POF) KW - Glass optical fibre (GOF) KW - POF OTDR KW - Brillouin sensor KW - BOTDA KW - BOFDA KW - Fibre Bragg grating (FBG) KW - Geosynthetics KW - Geotextiles KW - Technical textiles PY - 2011 UR - http://journals.bg.agh.edu.pl/GORNICTWO/2011-02/GG_2011_2_63.pdf SN - 1732-6702 SN - 0138-0990 VL - 35 IS - 2 SP - 597 EP - 604 PB - Uczelniane Wydawn. Naukowo-Dydaktyczne AGH CY - Kraków AN - OPUS4-23418 LA - pol AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jaunich, Matthias A1 - Stark, Wolfgang A1 - Wolff, Dietmar T1 - Low temperature properties of rubber seals N2 - Rubber is widely used as sealing material in various applications. In many fields the sealing function at low temperatures is necessary. Therefore the understanding of failure mechanisms is of high importance. Rubbers are normally used above their glass-rubber transition region but the minimum working temperature limit is not defined precisely. Therefore the lower operation temperature limit of rubber seals should be determined in dependence of the material properties. The results of Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA) are combined with the results of the standardized compression set according to ISO 815 respectively a modified test using the DMA equipment. N2 - Tiefentemperaturverhalten von Elastomerdichtungen Elastomere werden vielfach als Dichtungsmaterial für verschiedene Anwendungen eingesetzt. In vielen Bereichen ist die Funktion der Dichtung auch bei tiefen Temperaturen erforderlich. Daher ist das Verständnis des Versagensmechanismus von großer Bedeutung. Normalerweise werden Elastomere oberhalb ihres Glass-Gummi Übergangsbereiches eingesetzt aber die minimale Einsatztemperatur ist nicht exakt definiert. Daher ist es sinnvoll diese untere Temperatureinsatzgrenze in Abhängigkeit von den Materialeigenschaften zu bestimmen. Die Ergebnisse der DSC und der DMA werden mit den Ergebnissen des standardisierten Druckverformungsrestes nach ISO 815 und einer abgewandelten Messung mit der DMA kombiniert. KW - Sealing material KW - Elastomer KW - Compression set KW - Dynamic mechanical analysis KW - Low temperature behaviour PY - 2011 SN - 0948-3276 SN - 0022-9520 IS - 03 SP - 52 EP - 55 PB - Hüthig CY - Heidelberg AN - OPUS4-23422 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rethmeier, Michael A1 - Heinze, Christoph A1 - Lausch, Thomas T1 - Schweißspannungen bei Bauteilschweißversuchen unter besonderer Berücksichtigung des Einspanngrades T2 - Festkolloquium - Univ.-Prof. Dr.-Ing. H. Wohlfahrt CY - Braunschweig, Germany DA - 2011-03-11 PY - 2011 AN - OPUS4-23427 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabe, Torsten T1 - Integration of Ni-Cu-Zn Ferrite in LTCC-Modules T2 - 7th Intern. conf. and Exhib. on Ceramic Interconnect and Ceramic Microsystems Technologies/CICMT CY - San Diego, CA, USA DA - 2011-04-04 PY - 2011 AN - OPUS4-23488 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Steinborn, Gabriele A1 - Gemeinert, Marion T1 - Anwendung der Ultraschallspektrometrie zur Optimierung von keramischen Schlickern T2 - DKG-Jahrestagung 2011 CY - Saarbrücken, Germany DA - 2011-03-28 PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-234897 AN - OPUS4-23489 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Güther, Wolfgang A1 - Kaczmarek, Ch. A1 - Oder, Gabriele A1 - Rabe, Torsten T1 - Schadensuntersuchungen an Aluminiumoxid-Stahl-Lötverbunden auf Basis des Mo/Mn-Verfahrens T2 - DKG-Jahrestagung 2011 CY - Saarbrücken, Germany DA - 2011-03-28 PY - 2011 AN - OPUS4-23491 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulz, Bärbel A1 - Heunisch, Andreas A1 - Rabe, Torsten T1 - Hochpräzise Strukturierung von LTCC-Multilayern mittels Mikrofräsen T2 - DKG-Jahrestagung 2011 CY - Saarbrücken, Germany DA - 2011-03-28 PY - 2011 AN - OPUS4-23492 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nofz, Marianne A1 - Feigl, Michael A1 - Pulz, Robert A1 - Rehmer, Birgit A1 - Sojref, Regine A1 - Dörfel, Ilona T1 - Verhalten von Al2O3-Sol-Gel-Schichten auf Nickelbasislegierungen bei thermomechanischer Belastung T2 - Workshop "Materialien und Prozesstechniken der Turbinenschaufel-beschichtung" der Europ. Forschungsges. Dünne Schichten e. V. CY - Dresden, Germany DA - 2011-03-15 PY - 2011 AN - OPUS4-23493 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zachariev, G. A1 - Rudolph, Hans-Volker A1 - Ivers, Heinz A1 - Buchta, Lothar T1 - Prediction of fiber/matrix debonding kinetics in glass fibre reinforced polyoximethylene under creep N2 - Am Beispiel der zunehmenden Faser/Matrix-Enthaftung von glasfaserverstärktem Polyoxymethylen unter Kriechbelastung wird eine Vorhersagemethode für die Schadensakkumulation auf der Basis des Kurzzeitschadens und der Langzeitfestigkeit verifiziert. Für die Detektion der Schädigung wird das Kleinwinkel-Streuverfahren der Röntgen-Refraktometrie eingesetzt. Die Vorhersagemethode ist geeignet für Materialien mit delokalisierter Schädigung vor dem Versagensfall. Die Schadensvorhersage wird mit der experimentell bestimmten Schadensakkumuklation verglichen. N2 - A method for independent prediction of creep damage accumulation on the basis of damage at short term loading and long-term strength is verified for the case of fiber/matrix debonding of injection moulded short glass fibre reinforced polyoximethylene. Small angle Scattering X-ray refractometry is applied for damage registration. The method is applicable to materials which display delocalised damage prior to fracture. The predicted damage is compared with the experimental data for damage accumulation in creep. PY - 2011 SN - 0025-5300 VL - 53 IS - 1-2 SP - 58 EP - 61 PB - Hanser CY - München AN - OPUS4-23494 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Döring, Joachim A1 - Bovtun, Viktor Petrovic A1 - Brekow, Gerhard A1 - Kreutzbruck, Marc T1 - Charakterisierung der Wandler für Luftultraschallprüfung aus zellulärem Polypropylen-Ferroelektret T2 - 37th Annual Conference on Acoustics - DAGA 2011 CY - Düsseldorf, Germany DA - 2011-03-21 PY - 2011 AN - OPUS4-23496 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plagge, Michael A1 - Krüger, Simone A1 - Berger, Anka A1 - Deubel, Jan T1 - STA-FTIR Untersuchungen als Eingabeparameter für die numerische Simulation von Brandversuchen T2 - 19. Ulm-Freiberger Kalorimetertage CY - Freiberg, Germany DA - 2011-03-16 PY - 2011 AN - OPUS4-23408 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Werrel, Martin A1 - Krüger, Simone A1 - Deubel, Jan A1 - Piechotta, Christian A1 - Fettig, Ina T1 - Cone Calorimeter-Daten als Eingabeparameter für die numerische Simulation von Brandvorgängen T2 - 19. Ulm-Freiberger Kalorimetertage CY - Freiberg, Germany DA - 2011-03-16 PY - 2011 AN - OPUS4-23409 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Deubel, Jan A1 - Krüger, Simone A1 - Werrel, Martin A1 - Piechotta, Christian A1 - Fettig, Ina T1 - Kalorimetrische Untersuchungen zur Brandursachenermittlung T2 - 19. Ulm-Freiberger Kalorimetrietage CY - Freiberg, Germany DA - 2011-03-16 PY - 2011 AN - OPUS4-23410 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kupsch, Andreas A1 - Lange, Axel A1 - Hentschel, Manfred P. A1 - Müller, Bernd R. T1 - Refraction Effects in CT for Carbon Fibre Coating Detection by Iterative Reconstruction T2 - Vortrag am Gustav-Stresemann-Institut CY - Bonn, Germany DA - 2011-03-07 PY - 2011 AN - OPUS4-23411 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang T1 - Die Rolle des Staatlichen Materialprüfungsamtes Berlin-Dahlem bei der Typisierung der Pressmassen und der Gütesicherung T2 - 6th International Thermoset Conference CY - Iserlohn, Germany DA - 2011-03-23 PY - 2011 AN - OPUS4-23412 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bohmeyer, W. A1 - Lange, K. A1 - Stark, Wolfgang T1 - Prozesskontrolle mit Ultraschall US-plus T2 - 6th International Thermoset Conference CY - Iserlohn, Germany DA - 2011-03-23 PY - 2011 AN - OPUS4-23413 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Robertson, Daniela A1 - Böhning, Martin A1 - Schröder, Hartmut T1 - Möglichkeiten der Abschätzung der Langzeitbeständigkeit von Kunststoffdichtungsbahnen (KDB) auf Polyolefinbasis für den Tunnelbau T2 - 12. Informations- und Vortragstagung über Kunststoffe in der Geotechnik (FS-KGEO 2011) CY - Munich, Germany DA - 2011-03-03 PY - 2011 AN - OPUS4-23415 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beck, Uwe A1 - Reiners, Georg A1 - Weise, Matthias A1 - Hielscher, Stefan A1 - Lerche, D. A1 - Rietz, U. T1 - Conventional Testing of Bonding and Adhesive Strength vs. Centrifuge Test T2 - DGO AnSim Verwertungsworkshop CY - Berlin, Germany DA - 2011-03-23 PY - 2011 AN - OPUS4-23417 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Spaltmann, Dirk A1 - Reichelt, Manuel A1 - Scholz, Christian T1 - Reprofilierungsabhängiges Verschleißverhalten von Eisenbahnradmodelllaufflächen T2 - MRO-Konferenz CY - Berlin, Germany DA - 2011-03-25 PY - 2011 AN - OPUS4-23441 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Werner T1 - Voraussetzungen für die Zulassung von Geokunststoffen (insbesondere Bewehrungsgitter) für Deponieabdichtungen T2 - 27. Fachtagung "Die sichere Deponie" CY - Würzburg, Germany DA - 2011-02-23 PY - 2011 AN - OPUS4-23442 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin A1 - Matyschik, Jan T1 - Optimierung des Rückbaus/Abbruchs von Gebäuden zur Aufbereitung und Rückgewinnung von hochwertigen RC-Baustoffen T2 - Baustoff Recycling Forum CY - Nuremberg, Germany DA - 2011-02-10 PY - 2011 AN - OPUS4-23443 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Erfassung von potentiellen Schadstoffen bei Sportböden auf Kunststoffbasis (Kunststoff- und Kunststoffrasenbeläge) auf Sportfreianlagen unter Berücksichtigung von Alterungs- und Verschleißprozessen T2 - Einladung zur Sitzung des Güteausschusses der Gütegemeinschaft Kunststoffbeläge in Sportfreianlagen e. V. CY - Berlin, Germany DA - 2011-03-17 PY - 2011 AN - OPUS4-23444 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Lehmann, Jens T1 - Fe/S Freiheit bei der INOX Bearbeitung T2 - FGS Jahrestagung 2011 CY - Würzburg, Germany DA - 2011-03-24 PY - 2011 AN - OPUS4-23447 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heyn, Andreas T1 - Methoden und Geräte zur Korrosionsforschung - Gemeinsame Ergebnisse des MDZWP, der OvGU und der BAM T2 - Forschungsseminar des MDZWP CY - Magdeburg, Germany DA - 2011-04-01 PY - 2011 AN - OPUS4-23448 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lucassen, F. A1 - Franz, G. A1 - Romer, R. L. A1 - Wirth, R. A1 - Weise, Matthias A1 - Hertwig, Andreas T1 - The rutile-titanite reaction: Material transport along mineral interfaces and dissolution patterns on rutile T2 - European Geoscience Union General Assembly 2011 CY - Vienna, Austria DA - 2011-04-03 PY - 2011 AN - OPUS4-23449 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lucassen, F. A1 - Franz, G. A1 - Romer, R. L. A1 - Wirth, R. A1 - Weise, Matthias A1 - Hertwig, Andreas T1 - The rutile-titanite reaction: (I) 3D-View of a reaction front for a dissolution-precipitation reaction T2 - European Geoscience Union General Assembly 2011 CY - Vienna, Austria DA - 2011-04-03 PY - 2011 AN - OPUS4-23450 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Drescher, Daniela A1 - Kneipp, Janina A1 - Österle, Werner A1 - Orts Gil, Guillermo T1 - Investigation of cytotoxicity of silica nanoparticles using viability tests and surface-enhanced Raman spectroscopy T2 - Berliner Chemie Symposium CY - Berlin, Germany DA - 2011-04-07 PY - 2011 AN - OPUS4-23451 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Drescher, Daniela A1 - Kneipp, Janina A1 - Matschulat, Andrea T1 - Biological mulitplex applications of optical nanoprobes in live cells T2 - International Symposium "Molecular Plasmonics" CY - Jena, Germany DA - 2011-05-19 PY - 2011 AN - OPUS4-23452 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Merk, Virginia A1 - Kneipp, Janina T1 - Development and Characterization of New SERS Substrates for Biological Application T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 N1 - Geburtsname von Merk, Virginia: Joseph, V. - Birth name of Merk, Virginia: Joseph, V. AN - OPUS4-23454 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Merk, Virginia A1 - Kneipp, Janina T1 - Development and Characterization of New SERS Substrates for Bioanalytical Application T2 - Berliner Chemisches Symposium CY - Berlin, Germany DA - 2011-04-07 PY - 2011 N1 - Geburtsname von Merk, Virginia: Joseph, V. - Birth name of Merk, Virginia: Joseph, V. AN - OPUS4-23455 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fedelich, Bernard T1 - Modellierung des thermomechanischen Ermüdungsverhaltens einer thermisch hochbelasteten Gasturbinenschaufel T2 - Arbeitskreis AG-Turbo, TU Braunschweig CY - Braunschweig, Germany DA - 2011-03-30 PY - 2011 AN - OPUS4-23456 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank T1 - Aktuelle Aspekte der Qualitätssicherung bei Herstellung und Betrieb zulassungspflichtiger und nicht zulassungspflichtiger Verpackungen für Versandstücke zur Beförderung radioaktiver Stoffe T2 - BMVBS Informationsaustausch zur verkehrsrechtlichen Aufsicht CY - Bonn, Germany DA - 2011-03-01 PY - 2011 AN - OPUS4-23457 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gumenyuk, Andrey A1 - Gook, Sergej A1 - Rethmeier, Michael T1 - Weld Seam Formation and Mechanical Properties of Girth Welds Performed with Laser-GMA-Hybrid Process on Pipes of Grade X65 T2 - Electron beam and laser welding conference CY - Paris, France DA - 2011-03-15 PY - 2011 AN - OPUS4-23428 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pittner, Andreas A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - Welding Simulation by Means of Phenomenological and Empirical Modelling T2 - AnSim Workshop 2011 CY - Berlin, Germany DA - 2011-03-23 PY - 2011 AN - OPUS4-23429 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Oliver T1 - Naturwissenschaften in der Archäologie - Beispiele aus der archäometrischen Forschung T2 - EXCELLENCE CLUSTER TOPOI, Archäometrisches Kolloquium CY - Berlin, Germany DA - 2011-01-27 PY - 2011 AN - OPUS4-23436 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino A1 - Burkert, Andreas A1 - Heyn, Andreas T1 - Elektrochemische Untersuchungen und Micro-CT T2 - GfKORR-Arbeitskreis "Betriebliche kontinuierliche Korrosionsüberwachung - Corrosion Monitoring" CY - Dresden, Germany DA - 2011-05-11 PY - 2011 AN - OPUS4-23668 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wloka, Monika T1 - Neue Norm für Produktzertifizierungsstellen N2 - Die öffentliche Kommentierung des Entwurfs der ISO/IEC 17065 steht bevor. Die neue Norm wird die DIN EN 45011 und den ISO/IEC Guide 65 ersetzen. KW - DAkkS KW - Norm KW - ISO KW - DIN KW - Akkreditierung KW - Zertifizierungsstellen KW - Produkte PY - 2011 VL - 1 SP - 5 AN - OPUS4-23670 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fahmy, A. A1 - Mix, Renate A1 - Schönhals, Andreas A1 - Friedrich, Jörg Florian T1 - Structure-property relationship of thin plasma deposited poly(allyl alcohol) films N2 - Poly(allyl alcohol) films with a thickness of about 150 nm were deposited by pulse plasma polymerization onto different substrates (inorganic and organic). The structure/property relationships of these samples were studied in dependence on the duty cycle (DC) of the plasma by a broad combination of different techniques and probes. For the first time volume sensitive methods (FTIR and dielectric spectroscopy) are combined with surface analytics by employing XPS for that system. FTIR spectroscopy gives qualitatively the same dependence of the concentration of the OH groups on DC like XPS. The observed differences are discussed considering the different analytical depths of both the methods. The dielectric measurements show that the plasma deposited films are not thermally stable but undergo a post plasma chemical reaction during heating. The results obtained by dielectric spectroscopy are discussed in detail with the data from FTIR and XPS measurements. KW - Allyl alcohol KW - Dielectric properties KW - Plasma polymerization KW - Surface and bulk characterization KW - Thermal stability PY - 2011 DO - https://doi.org/10.1007/s11090-011-9297-0 SN - 0272-4324 VL - 31 IS - 3 SP - 477 EP - 498 PB - Plenum Publ. Corp. CY - New York, NY, USA AN - OPUS4-23671 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Nieslony, Gregor A1 - Noack, Volker A1 - Hagenow, Peter A1 - Kovacs, Oliver T1 - Current developments in container design testing for the Konrad repository N2 - The Konrad repository for not heat generating radioactive wastes was licensed first in 2002. But due to legal actions this license has not been finally confirmed before 2007. Subsequently, the Federal Office for Radiation Protection (BfS) began scheduling backfitting of the former iron ore mine into a repository. The licensed repository volume is 303,000 m3 based on estimations of expected waste volumes to be disposed off although the mine itself would offer a much larger volume. Once the repository is ready for Operation, waste packages can be disposed, but this is not expected before the end of this decade. Nevertheless, there is already today a great interest in qualified and certified waste conditioning and packaging for disposal requiring Containers, tested, evaluated and certified by BAM and BfS. Key points of the Konrad license concern comprehensive requirements for waste products and Containers. Details are described in BfS reports, which constitute the basic documents for the license. Following the final license confirmation a revision of these documents has been requested in order to include considerations of water poisoning substances. This work is currently done by BfS in Cooperation with the NLWKN of Lower Saxony and the Institute for Safety Technology (ISTec). Concerning the specification for Containers themselves no or only minor changes are expected. T2 - KONTEC 2011 - 10. Internationales Symposium "Konditionierung radioaktiver Betriebs- und Stilllegungsabfälle" CY - Dresden, Deutschland DA - 06.04.2011 KW - Cask KW - Safety KW - Repository KW - Design testing KW - Radioactive waste PY - 2011 SP - 683 EP - 695 AN - OPUS4-23672 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schwenk, Christopher A1 - Tikhomirov, D. A1 - Diether, T. T1 - Erste Spezifikation für die numerische Schweißsimulation - Normenausschuss Schweißtechnik (NAS) im DIN - DIN SPEC 32534-1:2011-03 "Numerische Schweißsimulation - Durchführung und Dokumentation - Teil 1: Übersicht" N2 - Mit Ausgabedatum März 2011 ist die Spezifikation DIN SPEC 32534-1 erschienen. Die Spezifikation wurde im DIN/DVS-Gemeinschaftsausschuss NA 092-00-29 AA „Schweißsimulation (DVS AG I 2.1)" des Normenausschusses Schweißtechnik (NAS) im DIN in Zusammenarbeit mit dem Ausschuss für Technik (AfT) im DVS - Deutscher Verband für Schweißen und verwandte Verfahren e. V. nach dem Vornormverfahren erarbeitet. PY - 2011 SN - 0722-2912 SN - 0011-4952 VL - 5 SP - 129 EP - 130 PB - Beuth CY - Berlin AN - OPUS4-23673 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubcová, Petra A1 - Ramge, Peter A1 - Rübner, Katrin T1 - New lightweight aggregates from heterogeneous construction and demolition waste for the use in lightweight concrete N2 - Concrete containing lightweight aggregates has been known since ancient times. To reduce weight, natural aggregates of volcanic origin, such as crushed lava or pumice, were used in construction purposes, for example for the Pyramids during the Mayan period in Mexico or for monumental structures in the Roman Empire. The most famous examples of this first application of lightweight aggregate concrete (LWAC) in Europe are certainly the Colosseum and the Pantheon. The Roman constructors used natural as well as artificial aggregates, such as pumice, crushed lava and crushed brick, to realise lightweight concrete applications in parts of these buildings. Still today, pumice is used in Germany, Italy, Japan and Iceland as aggregate for structural lightweight concrete. T2 - European coatings congress CY - Nuremberg, Germany DA - 28.03.2011 KW - Sekundärrohstoffe KW - Sekundäre Gesteinskörnung KW - Recycling KW - Leichtbeton PY - 2011 SP - 1 EP - 8 AN - OPUS4-23674 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Merchel, S. A1 - Bremser, Wolfram A1 - Alfimov, V. A1 - Arnold, M. A1 - Aumaître, G. A1 - Benedetti, L. A1 - Bourlès, D.L. A1 - Caffee, M. A1 - Fifield, L.K. A1 - Finkel, R.C. A1 - Freeman, S.P.H.T. A1 - Martschini, M. A1 - Matsushi, Y. A1 - Rood, D.H. A1 - Sasa, K. A1 - Steier, P. A1 - Takahashi, T. A1 - Tamari, M. A1 - Tims, S.G. A1 - Tosaki, Y. A1 - Wilken, K. M. A1 - Xu, S. T1 - Ultra-trace analysis of 36Cl by accelerator mass spectrometry: an interlaboratory study N2 - A first international 36Cl interlaboratory comparison has been initiated. Evaluation of the final results of the eight participating accelerator mass spectrometry (AMS) laboratories on three synthetic AgCl samples with 36Cl/Cl ratios at the 10-11, 10-12, and 10-13 level shows no difference in the sense of simple statistical significance. However, more detailed statistical analyses demonstrate certain interlaboratory bias and underestimation of uncertainties by some laboratories. Following subsequent remeasurement and reanalysis of the data from some AMS facilities, the round-robin data indicate that 36Cl/Cl data from two individual AMS laboratories can differ by up to 17%. Thus, the demand for further work on harmonising the 36Cl-system on a worldwide scale and enlarging the improvement of measurements is obvious. KW - Accelerator mass spectrometry KW - Long-lived radionuclides KW - Cosmogenic nuclides KW - Exposure dating PY - 2011 DO - https://doi.org/10.1007/s00216-011-4979-2 SN - 1618-2642 SN - 1618-2650 VL - 400 IS - 9 SP - 3125 EP - 3132 PB - Springer CY - Berlin AN - OPUS4-23676 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Roebben, G. A1 - Emons, H. A1 - Reiners, Georg ED - Murashov, V. ED - Howard, J. T1 - Nanoscale reference materials N2 - Globalisation of both science and trade has increased the relevance of the ­comparability of measurement data whether in research, industry or regulatory contexts. Reference materials (RMs) are essential tools in the quest for comparable and reliable measurement results, a quest which laboratories, worldwide, are tasked with every day. An explicit acknowledgement of the importance of RMs in today’s measurement systems is found, for instance, in the laboratory accreditation standards, such as ISO/IEC 17025. PY - 2011 SN - 978-1-4419-7852-3 DO - https://doi.org/10.1007/978-1-4419-7853-0_3 IS - Chapter 3 SP - 53 EP - 75 PB - Springer Science + Business Media CY - New York Dordrecht Heidelberg London AN - OPUS4-23677 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schultz, C. A1 - Richter, M. A1 - Bonse, Jörn A1 - Quaschning, V. A1 - Fink, F. T1 - Laser-Ablation Behavior of Thin-Film Materials used in Silicon and GIGSe based Solar Cells T2 - 26th European Photovoltaic Solar Energy Conference CY - Hamburg, Germany DA - 2011-09-05 PY - 2011 AN - OPUS4-23618 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gross, Thomas T1 - Resümee des ersten Nutzertreffens deutscher Anwender von KRATOS ESCA-Spektrometern T2 - Zweites deutschsprachiges KRATOS ESCA Anwendertreffen 2011 CY - Kaiserslautern, Germany DA - 2011-05-12 PY - 2011 AN - OPUS4-23619 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pfennig, Anja A1 - Linke, Barbara A1 - Kranzmann, Axel T1 - Corrosion behaviour of pipe steels exposed for 2 years to CO2 -saturated saline aquifer environment similar to the CCS-site Ketzin, Germany N2 - When emission gasses are compressed into deep geological layers (CCS) CO2-corrosion of injection pipe steels is a relevant safety issue. The reliability of the steels used at the geological onshore CCS-site at Ketzin, Germany, is demonstrated in 2 years laboratory experiments under an equivalent corrosive environment at ambient pressure (T=60 °C, aquifer water, CO2-flow rate of 3 l/h). Corrosion kinetics and microstructures were characterized using samples of the heat treated steel 42CrMo4 (casing), and samples of the martensitic stainless steel X46Cr13 (injection). KW - Steel KW - Pipeline KW - Corrosion KW - CCS KW - CO2-storage PY - 2011 SN - 1876-6102 VL - 4 SP - 5122 EP - 5129 PB - Elsevier CY - Amsterdam AN - OPUS4-23621 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kuhlich, Paul A1 - Göstl, Robert A1 - Teichert, Philip A1 - Piechotta, Christian A1 - Nehls, Irene T1 - Transformations of polycyclic musks AHTN and HHCB upon disinfection with hypochlorite: two new chlorinated disinfection by-products (CDBP) of AHTN and a possible source for HHCB-lactone N2 - In this work, the behavior of the polycyclic musks 6-acetyl-1,1,2,4,4,7-hexamethyltetraline (AHTN) and 1,3,4,6,7,8-hexahydro-4,6,6,7,8,8-hexamethylcyclopenta- γ-2-benzopyran (HHCB) was investigated upon disinfection by using sodium hypochlorite as disinfectant in a model disinfection basin in order to find new disinfection byproducts (DBP). In the case of AHTN, the carboxylic acid 3,5,5,6,8,8-hexamethyl-5,6,7,8-tetrahydronaphthalene-2- carboxylic acid (AHTN-COOH) was generated by a haloform reaction, being the origin for two new chlorinated DBPs. In the case of HHCB, disinfection via hypochlorite led to the HHCB-lactone. All reaction products and intermediates were synthesized and isolated. The relevant degradation mechanisms are discussed in detail. KW - Musk KW - AHTN KW - HHCB KW - HHCB-lactone KW - Chlorination KW - Disinfection PY - 2011 DO - https://doi.org/10.1007/s00216-011-4674-3 SN - 1618-2642 SN - 1618-2650 VL - 399 IS - 10 SP - 3579 EP - 3588 PB - Springer CY - Berlin AN - OPUS4-23622 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rodrigues, M. A1 - Cappa, F. A1 - Schreiner, M. A1 - Ferloni, P. A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Woytek, B. A1 - Alram, M. T1 - Further metallurgical analyses on silver coins of Trajan (AD 98-117) N2 - Within an interdisciplinary project, preliminary results of which were published in 2007, a group of 65 silver coins (denarii) of Trajan, evenly distributed over the entire span of his reign (2nd to 6th consulate), as well as 3 coins from the reign of his predecessor, the emperor Nerva (AD 96–98), had been acquired on the coin market. These pieces could be cross-sectioned in order to carry out analyses. Measurements were performed with µ-XRF and µ-SRXRF to check the fineness of the denarius alloy as well as to investigate if the coins of the different consulates showed distinct traits concerning the main impurities which could suggest a change of ore sources. Furthermore, it was examined whether the influx of precious metals into the Roman treasury after Trajan's Dacian campaigns (AD 101/102 and 105/106) could have had any repercussions on the composition of the denarius alloy; comparative data was provided by the analysis of nine imitations of Roman Republican denarii presumably struck in Dacia. Documentation of the cross-sections was performed with SEM/EDX in order to clarify details concerning the specific microstructure of the coins. An enrichment of Ag of approx. 100 to 200 µm in the near surface regions of most of the coins could be observed, which is due to corrosion effects. Previous metallographic analyses done by several scholars had been inadequate to clarify the central numismatic and economic questions. With the presented analyses, it was possible to correct the results of the earlier research and to provide, for the first time, a secure basis of data for the investigation of the development of the silver alloy used for denarii in Trajan's reign. PY - 2011 DO - https://doi.org/10.1039/c0ja00252f SN - 0267-9477 SN - 1364-5544 VL - 26 IS - 5 SP - 873 EP - 1100 PB - Royal Society of Chemistry CY - London AN - OPUS4-23623 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hanelt, Sven A1 - Orts Gil, Guillermo A1 - Friedrich, Jörg Florian A1 - Meyer-Plath, Asmus T1 - Differentiation and quantification of surface acidities on MWCNTs by indirect potentiometric titration N2 - Wet-chemically oxidized carbon nanotubes (CNTs) generally exhibit both covalently-bound acidic functional groups on the surface and surface-adsorbed acidic substances, i.e. carbonaceous CNT fragments from the oxidation procedure. Direct potentiometric titration of oxidizable high surface area materials with dynamically desorbing acidic fragments is slow and inaccurate. Adsorbed acidic fragments are deprotonated by sodium hydroxide and form anions in solution which is not the case for covalently bound acidic groups on the CNTs, so the following filtration after NaOH treatment separates desorbable acidic substances from non-desorbable or covalently bound groups. For a known concentration of NaOH, titration of the eluate with hydrochloric acid (HCl) allows determination of the concentrations of both types of acidities. However, contrary to reports in the literature, the NaOH consumed by non-desorbed acidic groups has to be accounted for and impedes distinction of desorbed acidic groups via their pKa values. Results are presented of a study on the information content and the reliability of indirect potentiometric Boehm titration for different oxidized multi-walled CNTs. PY - 2011 DO - https://doi.org/10.1016/j.carbon.2011.03.016 SN - 0008-6223 SN - 1873-3891 VL - 49 IS - 9 SP - 2978 EP - 2988 PB - Pergamon Press CY - New York, NY AN - OPUS4-23625 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holst, N. A1 - Khakpour, Thomas A1 - Holtappels, Kai A1 - Steinbach, J. T1 - Ignition behavior of methane-oxygen mixtures at elevated conditions N2 - Self-ignition behavior of mixtures of methane and oxygen was investigated in a temperature range from 600 to 800°C. Variations of mixture composition, inert gas content, temperature and filling rate of the ignition autoclave were carried out in order to establish process boundaries for high temperature partial oxidation processes. The tests show that considerably high methane contents are needed to avoid an ignition. Heating-up tests show that ignition is possible at surprisingly low temperatures. This can be attributed to pre-ignition reactions that produce more instable intermediates. T2 - 2011 AIChE Spring meeting & 7th global congress on process safety CY - Chicago, IL, USA DA - 13.03.2011 KW - Safety KW - Explosion KW - Self-ignition KW - Methane KW - Partial oxidation PY - 2011 SN - 978-0-8169-1067-10 IS - Topical 1 / #13 / 13h SP - 1 EP - 10 CY - New York, NY, USA AN - OPUS4-23626 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thater, R. A1 - Perret, William A1 - Schwenk, Christopher A1 - Alber, U. A1 - Rethmeier, Michael ED - Vollertsen, F. T1 - Different modeling approaches for efficient distortion calculation of an automotive assembly N2 - In contrast to other simulation fields like forming simulation, welding simulation is still not widely used in industrial environments. A high user expertise, a high time-to-solution and the result accuracy are the most important problems that hinder its extensively application. Different modeling approaches influence these aspects and an analysis of their implementation is of interest especially for the automotive industry as a key user for production Simulation. T2 - International workshop on thermal forming and welding distortion - IWOTE´ 11 CY - Bremen, Germany DA - 06.04.2011 KW - Welding distortions KW - Automotive assembly KW - Modeling approach KW - Time-to-solution PY - 2011 SN - 978-3-933762-35-1 SP - 279 EP - 291 CY - Bremen AN - OPUS4-23627 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fontana, Patrick A1 - Müller, Urs A1 - Malaga, Katarina A1 - Lagerblad, B. A1 - Meng, Birgit T1 - Precast concrete facade elements with low embodied energy N2 - Concrete is by far the most common building material in the world. Due to its good durability it is widely used in building envelopes. One major part of the embodied energy in concrete comes from the production of Portland cement that consumes around 3,500 MJ energy per each ton of cement. Globally 2.6 billion tons of Portland cement is produced and the consumption is increasing. Since concrete will be used as main building material also in future construction, it is reasonable to develop concrete building components with lower embodied energy.Using the example of an ultra-high performance concrete (UHPC) façade element, it is demonstrated how the embodied energy can be reduced by application of hydrothermal curing. T2 - ENBRI Workshop - reaching the nearly zero-energy goal for buildings CY - Boras, Sweden DA - 04.04.2011 KW - UHPC KW - Betonfertigteil KW - Fassaden KW - Autoklavierung KW - Nachhaltigkeit PY - 2011 SN - 978-91-86622-51-0 SN - 0284-5172 SP - 1 EP - 8 AN - OPUS4-23628 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Favet, J. A1 - Lapanje, A. A1 - Giongo, A. A1 - Kennedy, S. A1 - Aung, Y.-Y. A1 - Cataneo, A. A1 - Kort, R. A1 - Brumsack, H.-J. A1 - Schnetger, B. A1 - Triplett, E.W. A1 - Beck, A. A1 - Broughton, William J. A1 - Gorbushina, Anna T1 - Microbial hitchhikers on intercontinental dust - Chadian origins T2 - VAAM-Jahrestagung 2011 CY - Karlsruhe, Germany DA - 03.04.2011 KW - Intercontinental dust KW - Desert soil PY - 2011 SN - 0947-0867 IS - EMP114 SP - 118 PB - Spektrum, Akad. Verl. AN - OPUS4-23629 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, M. A1 - Schultz, C. A1 - Bonse, Jörn A1 - Pahl, H.-U. A1 - Endert, H. A1 - Rau, B. A1 - Quaschning, V. A1 - Stegemann, B. A1 - Fink, F. T1 - Investigation of Material Removal during Laser-Scribing of Silicon and CIGSe based Thin-Film Solar Cells T2 - 2nd Workshop on CIGS Solar Cells Technology CY - Berlin, Germany DA - 2011-04-19 PY - 2011 AN - OPUS4-23630 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Torge, Manfred A1 - Sabel, Martin A1 - Feldmann, Ines A1 - Kohl, Anka T1 - Naturwissenschaftliche Untersuchungen im Rahmen des Projektes 'Konservierung mittelalterlicher Glasmalerei im Kontext spezieller materieller und umweltbedingter Gegebenheiten' N2 - Nachsicherung geschädigter Zaponlack-Wachs-Sicherungen an den um 1410/20 entstandenen Glasmalereien des Helenafensters nord VIII am Erfurter Dom - Untersuchungen zu Schadensursachen, Schadensphänomenen, Methoden der Nachbehandlung und des Monitorings KW - Glasmalerei KW - Restaurierung KW - Zaponlack PY - 2011 SN - 978-3-8167-8470-8 VL - D 1012 SP - 36 EP - 75 PB - Fraunhofer IRB Verl. CY - Stuttgart AN - OPUS4-23631 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Würth, Christian A1 - Grabolle, Markus A1 - Pauli, Jutta A1 - Spieles, Monika A1 - Resch-Genger, Ute T1 - Comparison of methods and achievable uncertainties for the relative and absolute measurement of photoluminescence quantum yields N2 - The photoluminescence quantum yield (Φf) that presents a direct measure for the efficiency of the conversion of absorbed photons into emitted photons is one of the spectroscopic key parameters of functional fluorophores. It determines the suitability of such materials for applications in, for example, (bio)analysis, biosensing, and fluorescence imaging as well as as active components in optical devices. The reborn interest in accurate Φf measurements in conjunction with the controversial reliability of reported Φf values of many common organic dyes encouraged us to compare two relative and one absolute fluorometric method for the determination of the fluorescence quantum yields of quinine sulfate dihydrate, coumarin 153, fluorescein, rhodamine 6G, and rhodamine 101. The relative methods include the use of a chain of Φf transfer standards consisting of several 'standard dye' versus 'reference dye' pairs linked to a golden Φf standard that covers the ultraviolet and visible spectral region, and the use of different excitation wavelengths for standard and sample, respectively. Based upon these measurements and the calibration of the instruments employed, complete uncertainty budgets for the resulting Φf values are derived for each method, thereby providing evaluated standard operation procedures for Φf measurements and, simultaneously, a set of assessed Φf standards. KW - Fluorescence KW - Photoluminescence KW - Quantum yield KW - Dye KW - Uncertainty KW - Absolute quantum yield KW - Method comparison KW - Integrating sphere PY - 2011 DO - https://doi.org/10.1021/ac2000303 SN - 0003-2700 SN - 1520-6882 VL - 83 IS - 9 SP - 3431 EP - 3439 PB - American Chemical Society CY - Washington, DC AN - OPUS4-23632 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zhu, Shengchao A1 - Fischer, Tobias A1 - Wan, Wei A1 - Descalzo López, Ana Belén A1 - Rurack, Knut T1 - Luminescence amplification strategies integrated with microparticle and nanoparticle platforms N2 - The amplification of luminescence signals is often the key to sensitive and powerful detection protocols. Besides optimized fluorescent probes and labels, functionalized nano- and microparticles have received strongly increasing attention in this context during the past decade. This contribution introduces the main signalling concepts for particle-based amplification strategies and stresses, especially the important role that metal and semiconductor nanoparticles play in this field. Besides resonance energy transfer, metal-enhanced emission and the catalytic generation of luminescence, the impact of multi-chromophoric objects such as dye nanocrystals, dendrimers, conjugated polymers or mesoporous hybrid materials is assessed. The representative examples discussed cover a broad range of analytes from metal ions and small organic molecules to oligonucleotides and enzyme activity. KW - Luminescence KW - Multi-chromosphore systems KW - Nanoparticles KW - Resonance energy transfer KW - Signal amplification PY - 2011 DO - https://doi.org/10.1007/128_2010_99 SN - 0340-1022 SN - 1436-5049 VL - 300 SP - 51 EP - 91 PB - Springer CY - Berlin ; Heidelberg [u.a.] AN - OPUS4-23633 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pentzien, Simone A1 - Conradi, Andrea A1 - Krüger, Jörg T1 - The influence of paper type and state of degradation on laser cleaning of artificially soiled paper N2 - Lasers can be a supplemental tool for restorers to overcome some of the limitations of traditional dry cleaning techniques for works of art on paper. The laser working range has to be optimized allowing for safe removal of contamination and limitation of damage to the substrate. This paper addresses the influence of paper type and state of degradation on laser working range. Three types of new paper (pure cellulose, bleached pulp paper, rag paper) were degraded and characterized with respect their degree of polymerization. Laser-induced damage thresholds of new and degraded paper were determined using SEM and viscometry. Additionally, artificially soiled model samples were made using two kinds of soiling, namely pulverized charcoal and soot-blackened standard test dust. Cleaning thresholds of soiled paper samples were evaluated. A working range for all combinations of paper and soiling between 0.05 J/cm2 and 0.5 J/cm2 was found for the application of 8-ns laser pulses at 532 nm wavelength. T2 - LACONA VIII - Lasers in the Conservation of Artworks VIII CY - Sibiu, Romania DA - 21.09.2009 KW - Nanosecond laser cleaning KW - Paper KW - Ageing KW - Degree of polymerization KW - Cleaning threshold KW - Damage threshold PY - 2011 SN - 978-0-415-58073-1 SP - 59 EP - 65 PB - Taylor & Francis CY - London, UK AN - OPUS4-23634 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute A1 - Behnke, Thomas A1 - Brehm, Robert A1 - Grabolle, Markus A1 - Hennig, Andreas A1 - Hoffmann, Angelika A1 - Hoffmann, Katrin A1 - Linck, Lena A1 - Lochmann, Cornelia A1 - Pauli, Jutta A1 - Spieles, Monika A1 - Würth, Christian T1 - Funktionelle Chromophor-Systeme, innovative Validierungskonzepte und rückführbare Standards für die fluoreszenzbasierte multiparametrische Bioanalytik N2 - Unter dem Motto „Innovation und Qualitätssicherung in der (Bio)Analytik“ werden in der Arbeitsgruppe Fluoreszenzspektroskopie der BAM, Bundesanstalt für Materialforschung und -prüfung, funktionelle Chromophor-Systeme, einfache Signalverstärkungs- und Multiplexingstrategien sowie innovative Validierungs- und rückführbare Standardisierungskonzepte für verschiedene fluorometrische Messgrößen und Methoden entwickelt. Im Mittelpunkt stehen dabei molekulare Fluorophore, Nanokristalle mit größenabhängigen optischen Eigenschaften (sogenannte Quantenpunkte, QDs) und fluoreszierende Partikel variabler Größe sowie Sonden und Sensormoleküle für neutrale und ionische Analyte und für die Charakterisierung von funktionellen Gruppen. Dabei erfolgen auch methodische Entwicklungen für die Fluoreszenzspektroskopie, die Fluoreszenzmikroskopie, die Milcrofluorometrie, die Sensorik und die Mikroarraytechnologie. Ziele sind u. a. das Design und die Untersuchung von multiplexfähigen selektiven und sensitiven Sonden für die Biomarkeranalytik, die Entwicklung von Methoden zur Charakterisierung der signalrelevanten Eigenschaften dieser Chromophor-Systeme und zur Charakterisierung von funktionellen Gruppen an Oberflächen und ihre Validierung sowie die Entwicklung und Bereitstellung von formatadaptierbaren, flexibel ersetzbaren Standards für die fluoreszenzbasierte Multiparameteranalytik. T2 - 5. Senftenberger Innovationsforum Multiparameteranalytik CY - Senftenberg, Deutschland DA - 10.03.2011 KW - Multiparametric KW - Multiplexing KW - Fluorescence KW - Nanoparticles KW - NIR dyes KW - Surface analysis KW - Quantum yield KW - Quantum dot KW - Lifetime PY - 2011 SP - 86 EP - 108 CY - Senftenberg AN - OPUS4-23635 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Umsetzung der Ökodesignrichtlinie in Deutschland T2 - Veranstaltung "Ökodesign - Umweltgerechtes Produzieren" CY - Regensburg, Germany DA - 2011-05-18 PY - 2011 AN - OPUS4-23636 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hoffmann, Katrin A1 - Behnke, Thomas A1 - Drescher, Daniela A1 - Kneipp, Janina A1 - Resch-Genger, Ute T1 - Lifetime-based discrimination between spectrally matching vis and NIR emitting particle labels and probes N2 - Increasing the information content from bioassays which requires robust and efficient strategies for the detection of multiple analytes or targets in a single measurement is an important field of research, especially in the context of meeting current security and health concerns. An attractive alternative to spectral multiplexing, which relies on fluorescent labels excitable at the same wavelength, yet sufficiently differing in their emission spectra or color presents lifetime multiplexing. For this purpose, we recently introduced a new strategy based on 'pattern-matching' in the lifetime domain, which was exemplary exploited for the discrimination between organic dyes and quantum dot labels revealing multi-exponential decay kinetics and allowed quantification of these labels. Meanwhile, we have succeeded in extending this lifetime multiplexing approach to nanometer-sized particle labels and probes absorbing and emitting in the visible (vis) and near-infrared (NIR) spectral region. Here, we present a first proof-of-principle of this approach for a pair of NIR-fluorescent particles. Each particle is loaded with a single organic dye chosen to display very similar absorption and emission spectra, yet different fluorescence decay kinetics. Examples for the lifetime-based distinction between pairs of these fluorescent nanoparticles in solution and in cells are presented. The results underline the potential of fluorescenc lifetime multiplexing in life science and bioanalysis. KW - Fluorescence KW - Fluorescence lifetime imaging microscopy KW - FLIM KW - Lifetime Multiplexing KW - Particle Label KW - Near-infrared KW - NIR KW - Cell imaging KW - Nanoparticles PY - 2011 DO - https://doi.org/10.1117/12.881442 SN - 1605-7422 VL - 7905 SP - 79051F-1 EP - 79051F-9 PB - SPIE, The International Society for Optical Engineering CY - Bellingham, Wash. AN - OPUS4-23637 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus A1 - Michael-Schulz, Heike T1 - Problems with formulations containing sodium carbonate peroxyhyrate T2 - IGUS EOS Meeting CY - Washington, D.C., USA DA - 2011-04-27 PY - 2011 AN - OPUS4-23648 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Michael-Schulz, Heike A1 - Malow, Marcus T1 - Some remarks on peroxyacetic acid preparations T2 - IGUS EOS Meeting CY - Washington, D.C., USA DA - 2011-04-27 PY - 2011 AN - OPUS4-23649 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Aris, Stephan T1 - Atemschutzflaschen im Blickpunkt der Europäischen Richtlinien über Druckgeräte T2 - Fortbildung der Ausbilder von Atemschutzgerätewarten der Deutschen Landesfeuerwehrschulen CY - Kassel, Germany DA - 2011-05-03 PY - 2011 AN - OPUS4-23650 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Noack, Volker A1 - Nieslony, Gregor A1 - Hagenow, Peter A1 - Kovacs, Oliver T1 - Aktuelle Entwicklungen auf dem Gebiet der Behälter-Bauartprüfungen für das Endlager KONRAD N2 - Das Endlager Konrad wurde bereits im Jahr 2002 als Endlager für nicht Wärme entwickelnde radioaktive Abfälle genehmigt. Jedoch wurde diese Genehmigung anschließend beklagt und konnte erst 2007 in letzter Instanz bestätigt werden. Nachfolgend hat das Bundesamt für Strahlenschutz (BfS) mit der Planung und Realisierung zum Umbau des ehemaligen Eisenerzbergwerkes zum Endlager begonnen. Das genehmigte Endlagervolumen beträgt 303.000 m3 und basiert auf Abschätzungen für die zu erwartende Abfallmenge. Das Bergwerk selbst böte ein deutlich größeres Volumen. Mit der Einlagerung von Behältern kann allerdings erst nach Fertigstellung des Endlagers und nach derzeitigem Stand voraussichtlich nicht vor Ende dieses Jahrzehnts gerechnet werden. Gleichwohl besteht bereits heute ein hohes Interesse an der endlagergerechten Konditionierung und Verpackung der für Konrad vorgesehenen radioaktiven Abfälle, wofür nicht zuletzt von der BAM bauartgeprüfte und vom BfS zugelassene Behälter erforderlich sind. Kernpunkte der Endlagergenehmigung sind umfassende Anforderungen an Abfallprodukte und Behälter. Einzelheiten sind in den vom BfS der Genehmigung zu Grunde liegenden Berichten und Endlageranforderungen definiert. Diese enthalten vor allem Anforderungen an die Abfallprodukte und an die zu deren Verpackung erforderlichen Behälter. Mit der Genehmigungserteilung wurde auch eine Überarbeitung dieser Endlageranforderungen und hinsichtlich der Berücksichtigung Wasser gefährdender Stoffe gefordert. Diese Arbeiten werden derzeit vom BfS in Zusammenarbeit mit dem Niedersächsischen Landesbetrieb für Wasserwirtschaft, Küsten- und Naturschutz (NLWKN) und dem Institut für Sicherheitstechnik (ISTec) vorgenommen. Hinsichtlich der Anforderungen an die Endlagerbehälter wird allerdings davon ausgegangen, dass die für die Behälterbauartprüfung wesentlichen abfallprodukt- und behälterspezifischen Anforderungen davon nicht oder nur unwesentlich berührt sein werden. T2 - KONTEC 2011 - 10. Internationales Symposium "Konditionierung radioaktiver Betriebs- und Stilllegungsabfälle" CY - Dresden, Deutschland DA - 06.04.2011 KW - Behälter KW - Sicherheit KW - Endlager KW - Bauartprüfung KW - Radioaktive Abfälle PY - 2011 SP - 683 EP - 695 AN - OPUS4-23652 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Korzen, Manfred T1 - Constitutive Equations for Structural Steel Subjected to Fire - Some Remarks T2 - International Conference APPLICATIONS OF STRUCTURAL FIRE ENGINEERING 2011 CY - Prague, Czech Republic DA - 2011-04-29 PY - 2011 AN - OPUS4-23653 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Werner, Jan A1 - Jochems, Frank T1 - Hilfestellung und Eigenverantwortung N2 - BK-Container - Bei Schüttgut-Containern unterscheidet man eine Vielzahl von Bauarten. Die sicherheitstechnische Bewertung ist deshalb für Hersteller, Prüfstellen und die BAM nicht einfach. KW - Allgemeiner Rückblick auf BK-Gefahrgutcontainer KW - Wiederkehrende Prüfung KW - Serienherstellung PY - 2011 SN - 0944-6117 VL - 3 SP - 18 EP - 19 PB - Vogel CY - München AN - OPUS4-23654 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hahn, Oliver ED - Trost, V. ED - Pataki-Hundt, A. ED - Huhsmann, E. T1 - Die Farben und Tinten im Stuttgarter Psalter - Naturwissenschaftliche Untersuchungen N2 - Die Miniaturen des Stuttgarter Psalters bestechen nicht nur durch ihre Originalität, sondern auch durch ihre außerordentliche Farbigkeit. Seit Urzeiten benutzen die Menschen farbige Substanzen, um Bilder entstehen zu lassen. Von den zahlreichen Quellen, die von der Gewinnung und Herstellung von Farben handeln, soll hier nur kurz berichtet werden. Eine ausführliche Darstellung über antike und frühmittelalterliche Rezeptsammlungen findet sich an anderer Stelle in diesem Katalog. Bereits seit der Antike gibt es eine Tradition, Zubereitungs- und Verarbeitungsrezepturen zu sammeln. So berichtet Theophrast im 4. Jahrhundert n. Chr. über mineralische Farbmittel, zahlreiche Informationen lassen sich auch aus dem 25 V. Chr. entstandenen Architekturtraktat des Vitruv und der etwa achtzig Jahre jüngeren Naturgeschichte des Plinius gewinnen. Aus dem 3. Jahrhundert sind dann erstmals auf drei griechischen Papyri echte Rezepturen zur Farbherstellung überliefert. Die außerordentliche Rezeptsammlung der Mappae Clavimla und die Handschrift Lucca, eine Sammlung kunsttechnologischer Rezepte, sind vermutlich ebenso griechischen Ursprungs. Das wachsende Interesse an diesen Rezeptsammlungen dokumentiert sich in zahlreichen Kopien, die im weiteren Verlauf nicht nur in Latein sondern in der entsprechenden Volkssprache verfasst wurden (Fuchs und Oltrogge 1998). KW - Röntgenfluoreszenzanalyse KW - VIS-Spektroskopie KW - Zerstörungsfreie Prüfung PY - 2011 SN - 978-3-88282-072-0 SP - 111 EP - 121 CY - Stuttgart AN - OPUS4-23657 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gross, Thomas T1 - Röntgenphotoelektronenspektroskopie in der Arbeitsgruppe Schicht- und Oberflächenanalytik T2 - Zweites deutschsprachiges Kratos ESCA Anwendertreffen CY - Kaiserslautern, Germany DA - 2011-05-12 PY - 2011 AN - OPUS4-23588 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lange, Axel A1 - Kupsch, Andreas A1 - Hentschel, Manfred P. A1 - Manke, I. A1 - Kardjilov, N. A1 - Arlt, Tobias A1 - Grothausmann, R. T1 - Reconstruction of limited computed tomography data of fuel cell components using direct iterative reconstruction of computed tomography trajectories N2 - CT (computed tomography) reconstructions of fuel cell components of a yet unrivaled spatial resolution and quality are presented. This is achieved by application of the novel DIRECTT (Direct Iterative Reconstruction of Computed Tomography Trajectories) algorithm. We focus on two different key issues which essentially rule the fuel cell's durability on different length scales and physical interactions. On the resolution scale of some 100 µm agglomerations of condensed water in flow-field channels are detected by means of quasi-in situ neutron CT (after operation). Five orders of magnitude below nanometer sized Ru catalyst particles on carbon black support are visualized by electron tomography. Both types of experiments are especially adapted to the type of material involved but they are accompanied by severe deviations from ideal CT measuring conditions, as well. In order to overcome the tremendous reconstruction artifacts of standard algorithms, we employ DIRECTT which is described in detail. Comparisons of DIRECTT reconstructions to the conventional filtered back projection, prove the significant improvements in both experimental methods. KW - PEM fuel cell KW - Neutron computed tomography KW - Electron tomography KW - Reconstruction algrorithm KW - Water management KW - Catalyst PY - 2011 DO - https://doi.org/10.1016/j.jpowsour.2010.10.106 SN - 0378-7753 VL - 196 IS - 12 SP - 5293 EP - 5298 PB - Elsevier CY - Amsterdam [u.a.] AN - OPUS4-23589 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schurig, Michael A1 - Reich, Franziska A1 - Jochems, Frank A1 - Klinger, Christian ED - Ziegahn, K.-F. T1 - Vibrationsprüfungen an sicherheitskritischen Ventilen: Zwei Beispiele aus Forschung und Anwendung N2 - Ventile für gasförmige Medien müssen neben dem Druck oft auch Vibrationsbelastungen durch ihren Einsatz ertragen. Die dadurch entstehenden Massenkräfte können die Funktion des Ventils beeinflussen, indem z. B. die Anpresskraft im Ventilsitz dadurch verändert oder die Betätigungseinrichtung verstellt wird. Die schwellenden oder wechselnden Beanspruchungen können auch zu Ermüdungsschäden und damit zu dauerhaftem Funktionsverlust führen. Bei der Vibrationsprüfung für ein pneumatisch ausgelöstes Schnellöffnungsventil eines CO2-Feuerlöschsystems wurde die relevante EN 12094-4 angewendet. Diese setzt Mindestanforderungen in Hinblick auf die Schwingfestigkeit durch eine Gleitsinusprüfung. Im Gegensatz dazu steht die im Rahmen eines Forschungsvorhabens durchgeführte Vibrationsprüfung an einem Sicherheitsventil für Tanklastwagen, bei der ein umfangreicheres Prüfprogramm erstellt wurde, um vibrationsabhängiges Ansprechen des Ventils zu untersuchen. T2 - 40. Jahrestagung der GUS 2011 - Umwelteinflüsse erfassen, simulieren, bewerten CY - Stutensee-Blankenloch/Karlsruhe DA - 30.03.2011 KW - Vibrationsprüfung KW - Schockprüfung KW - Sicherheitsventile KW - Schwingungsbedingtes Ansprechen PY - 2011 SN - 978-3-9813136-1-1 IS - V17 SP - 1 EP - 12 PB - DWS Werbeagentur und Verlag GmbH CY - Karlsruhe AN - OPUS4-23591 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Maskos, Michael A1 - Berger, Georg A1 - Braun, Ulrike A1 - Heyn, Andreas A1 - Klinger, Christian A1 - Wachtendorf, Volker T1 - Schadensanalyse und Beständigkeit von Materialien in biomedizinischen Einsatzgebieten N2 - Der Anteil von Polymeren als Funktions- und Konstruktionswerkstoffe in dauerhaften medizinischen Anwendungen steigt beständig. Derartige Materialien müssen den mechanischen, biologischen und chemischen Bedingungen im Körper widerstehen (u.a. Abrieb, Hydrolyse, Degradation) und gleichzeitig gut verträglich sein. Der sichere Einsatz von polymeren Materialien erfordert die Kenntnisse über ihre Langzeitstabilität unter verschiedenen äußeren Bedingungen. Diese sind nicht nur beeinflusst durch die unmittelbare Umgebung in vivo, sondern auch durch die Historie der verwendeten Materialien. Dazu zählen u. a. erhöhte Temperaturen unter sauerstoffhaltiger Atmosphäre während der Verarbeitung oder die Exposition von ionisierender Strahlung oder reaktiven Radikalen während der Sterilisation. PY - 2011 SP - 83 EP - 85 CY - Berlin AN - OPUS4-23592 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Einsatz des Lichtbogenofens für die Wertstoffrückgewinnung aus Reststoffen - Forschungsthemen der BAM T2 - Sitzung des Arbeitskreises "Lichtbogenofenbetrieb" des Bundesverbandes der Deutschen Gießerei-Industrie (BDG) CY - Castrop-Rauxel, Germany DA - 2011-04-13 PY - 2011 AN - OPUS4-23593 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Stand und Weiterentwicklung der Ökodesign-Vorgaben T2 - Ökodesign als Instrument für mehr Energieeffizienz? CY - Bayreuth, Germany DA - 2011-05-17 PY - 2011 AN - OPUS4-23638 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Koch, Matthias A1 - Gärtner, Sonja A1 - Balski, Matthias A1 - Köppen, Robert A1 - Nehls, Irene T1 - Aus der Kartonverpackung in die Babynahrung N2 - Lebensmittel in Recyclingkartons finden sich längst in allen Supermärkten. Doch die schützende Verpackung kann zu einer Quelle für Kontaminationen durch Phthalate werden. Analytik und Migration dieser hormonell wirksamen Weichmacher sind daher ein aktueller Forschungsschwerpunkt. KW - Analytische Chemie KW - Lebensmittelchemie KW - Umweltanalytik KW - Gaschromatographie KW - Massenspektrometrie PY - 2011 DO - https://doi.org/10.1002/nadc.201178449 SN - 1439-9598 SN - 1521-3854 VL - 59 IS - 5 SP - 544 EP - 546 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-23639 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Umweltgerechte Gestaltung energieverbrauchsrelevanter Produkte (ErP) - Stand und Ausblick T2 - Globalnorm-Tagung "Umweltgerechte Produktentwicklung" CY - Pforzheim, Germany DA - 2011-05-17 PY - 2011 AN - OPUS4-23640 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ulrich, Armin A1 - Balke, Christian A1 - Otremba, Frank T1 - Brandverhalten von Gefahrguttanks - Erste Ergebnisse eines Forschungsvorhabens N2 - In einem von der BAM Bundesanstalt für Materialforschung und -prüfung durchgeführten Forschungsvorhaben wurde untersucht, inwieweit bei Gefahrguttanks im Brandfall ein 'BLEVE', d. h. ein Versagen der Umschließung mit anschließender Freisetzung der Flüssigkeit bzw. des verflüssigten Gases, verzögert bzw. verhindert werden kann. PY - 2011 SN - 2191-0073 VL - 1 IS - 5 SP - 13 EP - 19 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-23641 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Golze, Manfred T1 - Who and what are EUROLAB and TURKLAB? T2 - EUROLAB/TURKLAB Seminar CY - Istanbul, Turkey DA - 2011-04-13 PY - 2011 AN - OPUS4-23642 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus A1 - Rosenberg, Marika A1 - Michael-Schulz, Heike T1 - Validation of the UN test method N.5 T2 - IGUS EOS Meeting CY - Washington, D.C., USA DA - 2011-04-27 PY - 2011 AN - OPUS4-23643 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Janzen, R. A1 - Piechotta, Christian A1 - Boesel, A. A1 - Lischka, Susanne A1 - Sperling, M. A1 - Ehlbeck, J. A1 - Buscher, W. T1 - A New Microwave Induced Plasma Source for Speciation Analysis of Heavy Metals T2 - Plasma Winter Conference CY - Zaragoza, Spain DA - 2011-01-30 PY - 2011 AN - OPUS4-23644 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rauchegger, Christian A1 - Schalau, Bernd A1 - Thévenin, D. T1 - Experimentelle Untersuchungen zur Schwergasausbreitung - erste Ergebnisse T2 - ProcessNet - Arbeitsausschuss "Auswirkungen von Stoff- und Energiefreisetzungen" CY - Frankfurt am Main, Germany DA - 2011-05-05 PY - 2011 AN - OPUS4-23645 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Menrad, Andreas A1 - Goedecke, Thomas T1 - Innendruckprüfung von extrusionsgeblasenen Kunststoffhohlkörpern nach der Schädigung durch Chemikalien T2 - Polymerwisschenschaftliches Seminar, Fakultät III, Polymertechnik und Polymerphysik, TU Berlin CY - Berlin, Germany DA - 2011-04-27 PY - 2011 AN - OPUS4-23646 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus A1 - Michael-Schulz, Heike T1 - Simulated 50 kg package for SADT testing T2 - IGUS EOS Meeting CY - Washington, D.C., USA DA - 2011-04-27 PY - 2011 AN - OPUS4-23647 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Aris, Stephan T1 - Aktuelle Entwicklungen im Bereich der Europäischen Richtlinien über Druckgeräte - Teil 1: Richtlinie 97/23/EG über Druckgeräte und Richtlinie 2009/105/EG über einfache Druckbehälter N2 - Die Europäischen Richtlinien über Druckgeräte (1997/23/EG – PED, 2009/105/EG – SPVD und 1999/36/EG bzw. 2010/35/EU – TPED) werden derzeit formalen (PED und SPVD) bzw. wurden schon (TPED) inhaltlichen Änderungen unterworfen. Die PED und SPVD werden zusammen mit acht weiteren Richtlinien im Rahmen des Neuen Rechtsrahmens an den EU-Beschluss 768/2008/EG angeglichen. Dabei wird versucht, die PED gleichzeitig an die CLP-Verordnung anzugleichen, um ein ansonsten entstehendes Problem bei der unterschiedlichen Fluideinstufung nach PED und CLP-Verordnung zu verhindern. Die Frage der Anwendbarkeit der PED auf Flaschen für Atemschutzgeräte ist derzeit beim Juristischen Dienst der Europäischen Kommission anhängig, hat jedoch voraussichtlich keinen Einfluss auf die genannten laufenden Angleichungsverfahren. KW - Druckgeräte KW - PED KW - Einfache Druckbehälter KW - SPVD KW - Neuer Ansatz KW - Neuer Rechtsrahmen KW - CLP-Verordnung KW - Atemschutzflaschen PY - 2011 SN - 2191-0073 VL - 1 IS - 5 SP - 24 EP - 27 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-23658 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kannengießer, Thomas T1 - Wasserstoffanalytik und Degradation von Werkstoffeigenschaften von hochfesten Feinkornbaustählen T2 - Werkstofftechnisches Kolloquium CY - Graz, Austria DA - 2011-05-06 PY - 2011 AN - OPUS4-23659 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fedelich, Bernard A1 - Sievert, Rainer A1 - Schicker, Johannes A1 - Klingelhöffer, Hellmuth A1 - Skrotzki, Birgit T1 - Experimental Characterization and Modelling of Thermo Mechanical Fatigue of Cast Iron Turbochargers T2 - TMF-Workshop 2011, BAM CY - Berlin, Germany DA - 2011-05-12 PY - 2011 AN - OPUS4-23660 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit T1 - Comparison between material parameters of polyethylene grades and the test performance behaviour of packagings for the transport of dangerous goods T2 - IPRI 2011 CY - Berlin, Germany DA - 2011-05-16 PY - 2011 AN - OPUS4-23661 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bothe, Martin A1 - Mya, K.Y. A1 - Pretsch, Thorsten T1 - Synthesis of Nanocomposite-based Candidates for Shape Memory Polymers T2 - Synthesis and Integration Group Seminar, Institute of Materials Research and Engineering (IMRE) CY - Singapore DA - 2011-04-27 PY - 2011 AN - OPUS4-23662 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Paul, Andrea T1 - Untersuchungen an Biokohle -ein multi-spektroskopischer Ansatz T2 - Colloquium, ATB Potsdam, CY - Potsdam, Germany DA - 2011-04-29 PY - 2011 AN - OPUS4-23663 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bremser, Wolfram T1 - Dritte Ausgabe des EURACHEM/CITAC Leitfadens " Quantifying Uncertainty in Analytical Measurment": Was ist das? T2 - 17. Kolloquium von EUROLAB-D, BAM CY - Berlin, Germany DA - 2011-05-06 PY - 2011 AN - OPUS4-23664 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin A1 - Scheid, Marc T1 - Staubexplosionen: Gefahren und Schutzmaßnahmen T2 - Behörden-Erfahrungsaustausch, BAM/Umweltbundesamt CY - Berlin, Germany DA - 2011-05-09 PY - 2011 AN - OPUS4-23666 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sarfraz, Adnan A1 - Emmerling, Franziska T1 - In situ Study of the Crystallization of Metal Phosphonates T2 - SPP 1415 Winterschool CY - Eisenach, Germany DA - 2011-03-30 PY - 2011 AN - OPUS4-23610 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schoknecht, Ute T1 - Leachingtests for coatings and treated wood T2 - Tagung "Leaching of Biocides from Facade Coatings" CY - Rapperswil-Jona, Switzerland DA - 2011-05-24 PY - 2011 AN - OPUS4-23613 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübert, Thomas A1 - Tiebe, Carlo A1 - Banach, Ulrich T1 - Quality control of spices by multigas sensors T2 - International Symposium on Olfaction and Electronic Nose, ISOEN CY - New York City, NY, USA DA - 2011-05-02 PY - 2011 AN - OPUS4-23616 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schultz, C. A1 - Richter, M. A1 - Pahl, H.-U. A1 - Endert, H. A1 - Bonse, Jörn A1 - Stannowski, B. A1 - Schlattmann, R. A1 - Quaschning, V. A1 - Stegemann, B. A1 - Fink, F. T1 - Single Wavelength Laser Processing for Monolithically Connected Si and CIGS Thin Film Solar Cells T2 - 26th European Photovoltaic Solar Energy Conference CY - Hamburg, Germany DA - 2011-09-05 PY - 2011 AN - OPUS4-23617 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bidarra, A. A1 - Buzanich, Günter A1 - Coroado, J. A1 - Rocha, F. T1 - A multianalitical approach to the study of gold leaf from a baroque altarpiece T2 - Technart 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-23599 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Würth, Christian A1 - Hoffmann, Katrin A1 - Behnke, Thomas A1 - Ohnesorge, Marius A1 - Resch-Genger, Ute T1 - Polymer- and glass-based fluorescence standards for the near infrared (NIR) spectral region N2 - The widespread use and acceptance of fluorescence techniques especially in regulated areas like medical diagnostics is closely linked to standardization concepts that guarantee and improve the comparability and reliability of fluorescence measurements. At the core of such concepts are dependable fluorescence standards that are preferably certified. The ever rising interest in fluorescence measurements in the near-infrared (NIR) spectral region renders the availability of spectral and intensity standards for this wavelength region increasingly important. This encouraged us to develop approaches to solid NIR standards based upon dye-doped polymers and assess their applicationrelevant properties in comparison to metal ion-doped glasses. The overall goal is here to provide inexpensive, easily fabricated, and robust internal and external calibration tools for a broad variety of fluorescence instruments ranging e.g. from spectrofluorometers over fluorescence microscopes to miniaturized fluorescence sensors. KW - Fluorescence standard KW - PMMA KW - Photostability KW - Perylene KW - Rhodamine 800 KW - Dye-doped polymers KW - Glass KW - Laser dye PY - 2011 DO - https://doi.org/10.1007/s10895-010-0650-0 SN - 1053-0509 SN - 1573-4994 VL - 21 IS - 3 SP - 953 EP - 961 PB - Plenum Publ. Corp. CY - New York, NY AN - OPUS4-22184 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schurig, Michael A1 - Bertram, A. T1 - The torsional buckling of a cruciform column under compressive load with a vertex plasticity model N2 - The torsional buckling of a plastically deforming cruciform column under compressive load is investigated. The problem is solved analytically based on the von Kármán shallow shell theory and the virtual work principle. Solutions found in the literature are extended for path-dependent incremental behaviour as typically found in the presence of the vertex effect that is present in metallic polycrystals. At the critical load for buckling the direction of straining changes by an additional shear component. It is shown that the incremental elastic–plastic moduli are spatially nonuniform for such situations, contrary to the classical J2 flow and deformation theories. The critical shear modulus that governs the buckling equation is obtained as a weighted average of the incremental elastic–plastic moduli over the cross-section of the cruciform. Using a plasticity model proposed by the authors, that includes the vertex effect, the buckling-critical load is computed for a aluminium column both with the analytical model and a FEM-based eigenvalue buckling analysis. The stable post-buckling path is determined by the energy criterion of path-stability. A comparison with the experimentally obtained classical results by Gerard and Becker (1957) shows good agreement without relying on artificial imperfections as necessary in the classical J2 flow theory. KW - Buckling KW - Elastoplasticity KW - Plasticity KW - Torsion KW - Von–Karman-theory PY - 2011 DO - https://doi.org/10.1016/j.ijsolstr.2010.08.017 SN - 0020-7683 VL - 48 IS - 1 SP - 1 EP - 11 PB - Elsevier Ltd. CY - New York, NY AN - OPUS4-22234 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gaul, Holger A1 - Weber, Gert A1 - Rethmeier, Michael T1 - Evaluation of fatigue crack propagation in spot welded joints by stiffness measurements N2 - Resistance spot welded joints made of two advanced high strength steels (AHSS) and one high strength steel (HSS) were examined. In the high cycle fatigue regime tests were realised for one loading condition, and the load and the displacement were measured. From the load and displacement range, the stiffness was calculated and in situ normalised to its value after 1000 cycles. It was thus possible to use the normalised stiffness evaluated during the experiment as failure criterion for the fatigue test of resistance spot welded joints. In order to evaluate this failure criterion, fatigue cracks were produced in the three different steel grades mentioned above according to user-specified levels of the normalised stiffness. It was found that the fatigue crack area increases linearly and the through-sheet-thickness crack length exponentially with decreasing stiffness. The comparison of the fatigue crack propagation during the fatigue test of the three different tested base metals showed very similar values. The comparability of fatigue tests performed on spot welded joints might thus be improved by the in situ evaluated stiffness as a failure criterion. This can be also used in further work to verify results of computer simulations of the stress intensity factor at spot welds with the help of experimental results. KW - Resistance spot welding KW - Fatigue KW - Frequency KW - Stiffness KW - Advanced high strength steels KW - Crack growth PY - 2011 DO - https://doi.org/10.1016/j.ijfatigue.2010.12.005 SN - 0142-1123 VL - 33 IS - 5 SP - 740 EP - 745 PB - Elsevier CY - Oxford AN - OPUS4-22207 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tzschichholz, Grit A1 - Steinborn, Gabriele A1 - Hentschel, Manfred P. A1 - Lange, Axel A1 - Klobes, Peter T1 - Characterisation of porous titania yttrium oxide compounds by mercury intrusion porosimetry and X-ray refractometry N2 - Aiming at ceramic materials of low thermal radiation emittance titania yttrium oxide ceramics have been prepared by sintering in air at 1,100 and 1,400 °C, respectively, and characterised. Due to its high infrared refractive index, average pore sizes up to 1 µm for optimal Mie scattering cross sections and over 35% porosity the material is a promising candidate for elevated temperature insulations. The essentially in large pore growth is achieved by graphitic nano and micro particle additives. The microstructure parameters of porosity, specific surface area, median and average pore sizes are determined by mercury intrusion porosimetry. Beyond this classical technique supplementary measurements by X-ray Absorption and X-ray refractometry reveal considerably larger average pore sizes due to closed pores not accessible for mercury. An additional advantage of the X-ray techniques is their non-destructive application, which allows other treatments afterwards. The combined application of both methods provides additional information and reliability in case of complex ceramic microstructures and may serve for improved developments of porous ceramics with optimised thermal scattering for energy savings in high temperature applications. KW - Porous ceramics KW - Mercury intrusion porosimetry KW - X-ray refractometry KW - Porosity KW - Specific surface area KW - Average pore size PY - 2011 DO - https://doi.org/10.1007/s10934-010-9358-4 SN - 1380-2224 SN - 1573-4854 VL - 18 IS - 1 SP - 83 EP - 88 PB - Kluwer CY - Dordrecht AN - OPUS4-22977 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hertel, Horst A1 - Hanspach, Alexa A1 - Plarre, Rüdiger T1 - Differences in alarm responses in drywood and subterranean termites (Isoptera: Kalotermitidae and Rhinotermitidae) to physical stimuli N2 - Alarm response triggered by physical stimuli is wide spread in termites but executed in several different behavioural patterns. The drywood and subterranean termite species tested in this study differed significantly by either head-drumming or jerking when stimulated by light, air-flow, or air borne Sound stimuli. Nevertheless, differences may have a common evolutionary base. Repetitive stimuli of the same quality led to reduced responses over time, which was interpreted as habituation behaviour, a simple form of learning. Adaptation as alternative explanation was ruled out because when termites were subjected with a dis-habituation-stimulus followed by the original stimulus full Response occurred again to this stimulus. KW - Incisitermes KW - Coptotermes KW - Head-drumming KW - Jerking KW - Habituation PY - 2011 DO - https://doi.org/10.1007/s10905-010-9240-x SN - 0892-7553 VL - 24 IS - 2 SP - 106 EP - 115 PB - Springer Science + Business Media B.V. CY - Dordrecht [u.a.] AN - OPUS4-22978 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Neumann, Martin A1 - Herter, Jürgen A1 - Droste, Bernhard A1 - Hartwig, S. T1 - Compressive behaviour of axially loaded spruce wood under large deformations at different strain rates N2 - Impact limiting components of packages for the transport of radioactivematerials are often designed as wood filled steel constructions. Wood absorbs major part of the impact energy in order to minimise the impact load acting upon the containment. Dynamic impact experiments with wood filled impact limiters showed different crushing mechanisms for axially loaded wood depending on their lateral constraint. Tests on spruce wood samples (Picea abies) were performed in order to clarify the influence of strain rate from static to 30 s-1 on a) compression strength, b) stress at a global strain level of 50%, and c) energy absorption capacity at 50% deformation, including statistical evaluation of the results. Results were as follows: strain rate increase led to significantly higher compression strength, stress and strain energy at a strain level of 50%. Lateral strain restriction had no effect on compression strength; it had a significant effect on stress and strain energy at strain level of 50%. Therefore, the definition of a general yield curve for wood under large deformations is not possible, the yield curve has to be chosen taking into account lateral constraints. KW - Compression KW - Wood KW - Spruce KW - Picea abies KW - Impact PY - 2011 DO - https://doi.org/10.1007/s00107-010-0442-x SN - 0018-3768 VL - 69 IS - 3 SP - 345 EP - 357 PB - Springer CY - Berlin ; Heidelberg AN - OPUS4-22980 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pedrero, Z. A1 - Murillo, S. A1 - Cámara, C. A1 - Schram, E. A1 - Luten, J.B. A1 - Feldmann, I. A1 - Jakubowski, Norbert A1 - Madrid, Y. T1 - Selenium speciation in different organs of African catfish (Clarias gariepinus) enriched through a selenium-enriched garlic based diet N2 - Speciation of Se in fish is needed to elucidate the metabolism of this element in living organisms in the marine environment. In this paper, selenium concentration and its species distribution in several organs and tissues (liver, gills, kidney, muscle and gastrointestinal tract) of African catfish fed with a selenium-enriched garlic based diet was studied. The intention of this paper is focused on both the investigation of selenium distribution in the soluble protein fraction and the detection of selenoaminoacids. Thus, two different procedures have been developed. In the first procedure, screening of selenium in proteins in the Tris-buffer soluble fraction of different tissues was carried out by size exclusion chromatography-inductively coupled plasma-mass spectrometry (SEC-ICP-MS) and by laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) after sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) separation and electroblotting onto membranes. For the amino acid analysis, several sample treatments for Se-species extraction, based on enzymatic hydrolysis, were compared. The best results were obtained for incubation at controlled temperature. Application of several sample treatments in conjunction with different chromatographic techniques (reverse phase, anion exchange and ion exchange/size exclusion) was crucial to unambiguous Se-species identification. In Se-enriched African catfish a noticeable increase in the content of selenium in different organs was observed, except for the liver, where the Se level remained unaltered. The kidney was the Se-target organ in animals fed with enriched Se food. Selenomethionine (SeMet) was the main Se species identified in fillet extracts, whereas the presence of selenocysteine (SeCys) was detected in the liver and both SeMet and SeCys were present in the kidney. PY - 2011 DO - https://doi.org/10.1039/c003889j SN - 0267-9477 SN - 1364-5544 VL - 26 IS - 1 SP - 116 EP - 125 PB - Royal Society of Chemistry CY - London AN - OPUS4-22981 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schurig, Michael A1 - Klinger, Christian T1 - A proposal to include nongaussian vibration in the IEC standard for random vibration, a horizontal safety standard T2 - Tagung IEC TC 104 "Environmental conditions, classification and methods of test" CY - San Diego, CA, USA DA - 2011-01-31 PY - 2011 AN - OPUS4-22998 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Riedel, Juliane A1 - Koch, Matthias A1 - Fettig, Ina A1 - Labsch, Erika A1 - Piechotta, Christian A1 - Köppen, Robert A1 - Nehls, Irene T1 - Vergällungsmittel in Ethanol T2 - Workshop "Etiketten in Nasssammlungen: Probleme und Lösungsansätze" (Museum für Naturkunde, Berlin) CY - Berlin, Germany DA - 2011-01-28 PY - 2011 AN - OPUS4-22999 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Holtappels, Kai A1 - Kluge, Martin A1 - Gebauer, Marek A1 - Eliezer, D. T1 - Pressure resistance of glass capillaries for hydrogen storage N2 - Ein entscheidendes Problem neuer Wasserstofftechnologien ist die leichte und sichere Lagerung ausreichender Mengen an Wasserstoff insbesondere für Nutzung bei tragbaren oder mobilen Anwendungen. Eine neue und innovative Technologie basierend auf gebündelte Kapillaren wurde entwickelt. Diese Systeme garantieren eine sichere Speicherung, Lagerung und kontrollierte Freisetzung von Wasserstoff, obgleich Speicherdrücke bis 1200 bar angewendet werden. Die neue Technologie ermöglicht die Lagerung einer erheblich größeren Menge Wasserstoff als andere Systeme und übertraf bereits die Zielsetzung des DOE 2010. Es wird erwartet, die DOE-Zielsetzung für das Jahr 2015 bereits in naher Zukunft zu erreichen. Hauptaspekt für die Speichertechnologie ist die Druckfestigkeit der Glaskapillaren. Es ist weithin bekannt, dass besonders Quarz eine dreimal höhere Festigkeit als Stahl hat. Gleichzeitig ist die Dichte ungefähr dreimal niedriger, was bedeutet, dass viel weniger Material notwendig ist, um die gleiche Druckfestigkeit zu erreichen. Die Druckfestigkeit einzelner Kapillare ist in der Abhängigkeit der Materialien, der Abmessungen, der Wandstärke etc. ermittelt worden, um optimale Parameter für die "finalen" Kapillaren herauszufinden. KW - Wasserstoffspeicherung KW - Glasstruktur KW - Druckefestigkeit KW - Berstdruck PY - 2011 SN - 0025-5300 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. VL - 53 IS - 1-2 SP - 14 EP - 18 PB - Hanser CY - München AN - OPUS4-23043 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Weltschev, Margit T1 - Duplex steel S 32304 - a low cost and corrosion-resistant alternative to the austenite containing molybdenum T2 - NACE Internat. Korrosionskonferenz CY - Houston, TX, USA DA - 2011-03-12 PY - 2011 AN - OPUS4-23012 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sturm, Christine A1 - Tavares, Luciana A1 - Kjelstrup-Hansen, J. A1 - Rubahn, H.-G. T1 - Bilayer polymer/oxide coating for organic semiconductors N2 - Organic materials have been given much attention due to their intriguing properties that can be tailored via synthetic chemistry tor specific applications combined with their low price and fairly straight-forward large- scale synthesis. Para-hexaphenylene (p6P) nanofibers emit polarized light with a highly anisotropic emission profile, act a sub-wavelength optical waveguides, and form the basis tor a new type of miniature OLEDs. However, p6P molecules suffer reduction of luminescence intensity during photoexcitation under UV light. Such photoreaction is understood as a consequence of the interaction of the fibers with oxygen. We have developed a bilayer coating that does not change significantly the p6P spectrum but strongly reduces bleaching. This bilayer coating consists of a first layer of a stable polymer (PMMA) on top of the organic nanofibers as a protecting layer tor avoiding modifications of the p6P luminescence spectrum and as a second layer SiOx tor blocking the oxygen penetration. In this work, we show the applicability of this bilayer coating of PMMA/SiOx in prolonging the operationallifetime of field-effect transistor (FET) devices based on p6P nanofibers. The coating prevents strang degradation of transferred nanofibers on FET platforms during electrical biasing as is observed tor uncoated devices. We are currently investigating the effect of, the coating during electrically stimulated light emission experiments tram transferred fibers on transistor platforms. T2 - E-MRS ICAM IUMRS 2011 Spring Meeting; IUMRS ICAM 2011 & E-MRS / MRS Bilateral Conference on Energy CY - Nice, France DA - 2011-05-09 PY - 2011 AN - OPUS4-23013 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Drescher, Daniela A1 - Orts Gil, Guillermo A1 - Laube, G. A1 - Natte, Kishore A1 - Veh, R.W. A1 - Österle, Werner A1 - Kneipp, Janina T1 - Toxicity of amorphous silica nanoparticles on eukaryotic cell model is determined by particle agglomeration and serum protein adsorption effects N2 - Cell cultures form the basis of most biological assays conducted to assess the cytotoxicity of nanomaterials. Since the molecular environment of nanoparticles exerts influence on their physicochemical properties, it can have an impact on nanotoxicity. Here, toxicity of silica nanoparticles upon delivery by fluid-phase uptake is studied in a 3T3 fibroblast cell line. Based on XTT viability assay, cytotoxicity is shown to be a function of (1) particle concentration and (2) of fetal calf serum (FCS) content in the cell culture medium. Application of dynamic light scattering shows that both parameters affect particle agglomeration. The DLS Experiments verify the stability of the nanoparticles in culture medium without FCS over a wide range of particle concentrations. The related toxicity can be mainly accounted for by single silica nanoparticles and small agglomerates. In contrast, agglomeration of silica nanoparticles in all FCS-containing media is observed, resulting in a decrease of the associated toxicity. This result has implications for the evaluation of the cytotoxic potential of silica nanoparticles and possibly also other nanomaterials in standard cell culture. KW - Agglomeration KW - Cytotoxicity KW - Fibroblast cells KW - Serum proteins KW - Silica nanoparticles PY - 2011 DO - https://doi.org/10.1007/s00216-011-4893-7 SN - 1618-2642 SN - 1618-2650 VL - 400 IS - 5 SP - 1367 EP - 1373 PB - Springer CY - Berlin AN - OPUS4-23678 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schurig, Michael T1 - Mechanisch-dynamische Normungsarbeit Ergebnisbericht TC104 MT 17 San Diego T2 - Tagung DKE K 131 Umgebungsbedingungen, Klassifizierung und Prüfung CY - Oberkochen, Germany DA - 2011-05-11 PY - 2011 AN - OPUS4-23679 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian T1 - Strength of composite structural parts - role of the fiber/matrix interface N2 - The strength of laminates distinctly depends on the transverse strength of the laminas. The transverse failure is dominated by the adhesion between fiber and matrix. Usual strength criteria however do not take into account the adhesive strength explicitly. The determination of the interface strength is performed on the micromechanical scale using single fiber specimens. The fibers are loaded under off-axis loading while the debonding is monitored under a microscope. The stresses acting in the Interface are calculated by finite element analyses. It is found that for off-axial angles up to 35° interfacial debonding is the dominant failure mode while fiber breakage takes place at lower angles. The occurrence of fiber breakage and debonding under off-axis loading shows that the restriction to two potential failure planes - perpendicular or parallel to the fibers - as applied in common failure criteria has to be put in question. T2 - SEICO 11 - SAMPE Europe - 32nd International technical conference CY - Paris, France DA - 28.03.2011 KW - Composites KW - Strength KW - Adhesion PY - 2011 SN - 978-3-9523565-3-1 IS - Session 3B SP - 250 EP - 257 AN - OPUS4-23680 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kargol, Marta A1 - Müller, Urs A1 - Gardei, André A1 - Meng, Birgit T1 - Influence of blended cements on the performance of water repellent agents N2 - Ingress of moisture and harmful ions (e.g. Chloride, sulfate) into cementitious materials is one of the major factors in defining their durability. Modifications of building materials by targeted deposition of surface functional agents that make the surface hydro- and/or oleophobic aim to minimize moisture and ion ingress, and thus extend Service life of the cement based structures. Water repellent and easy-to-clean coatings for inorganic Substrates have gained strong attention during the last few years and various formulations based on silicones or alkylpolysiloxanes have been developed. Cementitious building materials are highly complex Systems with many components and changing properties in the course of a building’s Service life. The interactions between the Chemical agents and the cement based materials depend on many factors. The Chemical properties of the material Substrate appear to be the most important but in the context of their influence on the functionality of silanes and/or siloxanes these characteristics have not been well understood yet. The aim of this study was to evaluate the effect of different blended cements on water repellent agents’ performance. Two organosilicon compounds were applied on fresh blended cements containing limestone (L), fly ash (F), slag (S) and trass (T), and investigated in terms of their functionality. The surface properties of functionalized blended cements were studied based on wettability, i.e. contact angle measurements, before and after exposure to artificial and natural weathering. The first results indicate that slag and trass more distinctly affect the water repellent Surface performance after aging. T2 - Hydrophobe VI - 6th International conference on water repellent treatment of building materials CY - Rome, Italy DA - 12.05.2011 KW - Hydrophobic surfaces KW - Wettability KW - Impregnation KW - Blended cement KW - Silanes PY - 2011 SN - 978-3-931681-99-9 SP - 23 EP - 32 PB - Aedificatio Publishers AN - OPUS4-23681 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Fischer, Joachim A1 - Lehmann, Jens A1 - Ebell, Gino T1 - DGZfP - Merkblatt elektrochemische Potentialmessungen zur Detektion von Bewehrungsstahlkorrosion N2 - Im DGZfP- Fachausschuss für zerstörungsfreie Prüfling im Bauwesen - Unterausschuss Korrosionsnachweis bei Stahlbeton haben sich die Universitäten München, Aachen, Stuttgart und Braunschweig sowie die BAM Berlin an der Überarbeitung des Merkblatts B 3: „Elektrochemische Potentialmessungen zur Detektion von Bewehrungsstahlkorrosion“ beteiligt. Das Merkblatt wurde komplett überarbeitet und bietet jetzt umfangreichere Hinweise zur Durchführung der Messungen und deren Auswertung. Wesentlich stärker als zuvor geht das Merkblatt auf mögliche Einflüsse und Fehlerquellen sowie die für eine Interpretation der Daten notwendigen begleitenden Bauwerksuntersuchungen ein. Die nachfolgenden Ausführungen greifen einige wesentliche Aspekte in enger Anlehnung an die Ausführungen des Merkblatts B3 auf. Das vollständige Merkblatt ist über die DGZfP e.V. online zu beziehen. T2 - 3-Länder-Korrosionstagung - Möglichkeiten des Korrosionsschutzes von Stahl im Betonbau CY - Wien, Austria DA - 05.05.2011 KW - Verfahrensbeschreibung KW - Messraster KW - Einflußgrößen KW - Fehlerquellen KW - Prüfprotokoll KW - Nachweisgrenzen PY - 2011 SN - 978-3-935406-45-1 SP - 124 EP - 131 PB - DECHEMA CY - Frankfurt am Main AN - OPUS4-23682 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thöns, Sebastian A1 - Rücker, Werner T1 - Risikobasierte Überwachungsverfahren zur Lebensdauerverlängerung von bestehenden und neuen Bauwerken. T2 - DVM-Tag 2011: Bauteilzuverlässigkeit - Schäden und ihre Vermeidung, BAM CY - Berlin, Germany DA - 2011-05-04 PY - 2011 AN - OPUS4-23683 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stößer, R. A1 - Feist, M. A1 - Patzwaldt, K. A1 - Menzel, Michael A1 - Emmerling, Franziska ED - Brooks, H. T1 - Redox reactions of K3[Fe(CN)6] during mechanochemically stimulated phase transitions of AlOOH N2 - Thermally induced redox reactions of K3[Fe(CN)6] (1) were investigated for a broad temperature range by thermal methods and structure analytical methods (ESR and Mößbauer spectroscopy, X-ray Powder diffraction and XANES). Based on the influence of the mechanically activated and transforming matrices 2 and 3, redox processes can be tuned to form doped Al2O3 systems which contain either isolated Fe3+ centres or redox active phases and precursors like (Al1-xFex)2O3 (4), (Al3-xFex)O4 (5), Fe3O4, Fe2O3 and Fe0. The phase Fe3C and the chemically reactive C-species were detected during the reaction of 1. The final composition of the doped products of α-Al2O3 is mainly influenced by the chemical nature of the Fe doping component, the applied temperature and time regime, and the composition of the gas phase (N2, N2/O2 or N2/H2). From the solid state chemistry point of view it is interesting that the transforming matrix (2 and 3) possesses both oxidative and protective properties and that the incorporation of the Fe species can be performed systematically. KW - A. Inorganic compounds KW - C. Mössbauer spectroscopy KW - C. Thermogravimetric analysis KW - D. Electron paramagnetic resonance KW - ESR-Spektroskopie KW - Kaliumhexacyanoferrat(III) KW - Mechanische Aktivierung KW - Mößbauer-Spektroskopie KW - Redoxreaktionen KW - TA-MS-Messungen PY - 2011 DO - https://doi.org/10.1016/j.jpcs.2011.03.016 SN - 0022-3697 VL - 72 IS - 6 SP - 794 EP - 799 PB - Pergamon Press CY - New York, NY AN - OPUS4-23685 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schindhelm, S. A1 - Mach, Reinhard A1 - Teipel, U. A1 - Meyer-Plath, Asmus T1 - Optimierung von Verfahren zur Injektion und Separation der Partikel-Prozessgas-Ströme bei der Plasmamodifizierung von CNT T2 - 5. Symposium Produktgestaltung in der Partikeltechnologie CY - Pfinztal, Germany DA - 2011-05-19 PY - 2011 AN - OPUS4-23686 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beck, Uwe A1 - Reiners, Georg A1 - Weise, Matthias A1 - Hielscher, Stefan A1 - Lerche, D. A1 - Rietz, U. T1 - Conventional Testing of Bonding and Adhesive Strength vs. Centrifuge Test T2 - NIST-Workshop CY - Gaithersburg, MD, USA DA - 2011-04-27 PY - 2011 AN - OPUS4-23687 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Breit, W. A1 - Dauberschmidt, C. A1 - Gehlen, C. A1 - Sodeikat, C. A1 - Taffe, Alexander A1 - Wiens, U. T1 - Zum Ansatz eines kritischen Chloridgehaltes bei Stahlbetonbauwerken N2 - Der Chloridgehalt, ab dem bei der Bewehrung im Beton mit Korrosion gerechnet werden muss, wird als kritischer Chloridgehalt bezeichnet. Die Höhe dieses kritischen Chloridgehaltes bestimmt in hohem Maße den Instandsetzungsumfang und damit die Instandsetzungskosten. Zahlreiche Labor- und Bauwerksuntersuchungen belegen, dass dieser kritische Chloridgehalt von einer Vielzahl von Parametern abhängt und deswegen kein fester Wert sein kann. Aus diesem Grund ist es sinnvoll, über Betrachtung von Korrosions- bzw. Depassivierungswahrscheinlichkeiten einen unteren kritischen Chloridgehalt zu bestimmen, bei dem bei gegebenen Randbedingungen nur mit einer geringen Wahrscheinlichkeit (z. B. 5%-Fraktilwert) Korrosion von Stahl in Beton zu erwarten ist. Die Auswertung von zahlreichen Untersuchungen zeigt, dass der Ansatz eines kritischen Chloridgehaltes von 0, 5 M.-% bezogen auf den Zementgehalt bei Einhaltung bestimmter Randbedingungen mit einer hinreichend geringen Korrosionswahrscheinlichkeit korreliert und somit auch in Übereinstimmung mit der Richtlinie 'Schutz und Instandsetzung von Betonbauteilen' des DAfStb als unterer kritischer Chloridgehalt unter Praxisbedingungen anzusetzen ist. KW - Dauerhaftigkeit KW - Instandsetzung KW - Korrosion KW - Lebensdauer KW - Parkhäuser KW - Tiefgaragen KW - Betontechnologie KW - LIBS KW - Alkalität KW - Bewehrungsoberfläche KW - Bohrkernproben KW - Bohrmehl KW - Chloridgehalt KW - Chloridinduzierte Korrosion KW - Chloridprofile KW - Dauerhaftigkeitsbemessungen KW - Depassivierung KW - Depassivierungswahrscheinlichkeiten KW - Lochfraßkorrosion KW - Monitoring KW - Passivität KW - Potentialfeldmessungen KW - Probenentnahme KW - Richtlinie für Schutz und Instandsetzung KW - RL-SIB;Schädigungen KW - Baustoffe KW - Bauwerkserhaltung/Sanierung KW - Bauwerksüberwachung KW - Bewehrung PY - 2011 DO - https://doi.org/10.1002/best.201100007 SN - 0005-9900 SN - 1437-1006 VL - 106 IS - 5 SP - 290 EP - 298 PB - Ernst CY - Berlin AN - OPUS4-23758 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Lehmann, Jens T1 - Einsatz nichtrostender Stähle als Befestigungsmittel im Beton T2 - Betonmarketing Nord: Befestigungsmittel im Stahlbetonbau CY - Buchholz in der Nordheide, Germany DA - 2011-05-04 PY - 2011 AN - OPUS4-23761 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Oelgardt, C. A1 - Günster, Jens A1 - Heinrich, J.G. T1 - Characterization of the crystallization behavior of laser-fused transparent microspheres with the eutectic composition Al2O3-Y2O3-ZrO2 (AYZ) N2 - Transparent microspheres with the eutectic composition 65 Al2O3-16 Y2O3-19 ZrO2 (mol%) have been produced by laser fusing with a CO2 laser. The influence of the starting material – not pre-calcined and pre-calcined – as well as the laser power on the resulting microspheres – was investigated. After fabrication, the microspheres were analyzed by means of XRD to quantify the amorphous content of the spheres as well as to identify the residual crystalline phases, with a laser granulometer to measure the particle sizes of the starting material and the resulting microspheres, with DSC to characterize the glass transition temperature and crystallization behavior, and with SEM to investigate the microstructure of the microspheres. The laser-treated materials consist of transparent and opaque beads as well as sintered particles. The amorphous amount in the samples was detected to be ~ 85 %. Based on these results transparent beads were collected and annealed over a range of temperatures to analyze the crystallization behavior. KW - Eutectic ceramics KW - Al2O3-Y2O3-ZrO2 KW - Laser processing KW - Crystallization behavior KW - Microstructure PY - 2011 DO - https://doi.org/10.4416/JCST2011-00010 SN - 2190-9385 VL - 02 IS - 02 SP - 103 EP - 110 PB - Göller CY - Baden-Baden AN - OPUS4-23763 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Procop, Mathias A1 - Hodoroaba, Vasile-Dan A1 - Rackwitz, Vanessa T1 - A microfocus X-ray source for improved EDS and XRF analysis in the SEM N2 - A microfocus X-ray source mounted on the analysis chamber of an SEM was used to excite X-ray fluorescence spectra and to detect chemical elements with concentrations below the detection limit of the electron-excited X-ray spectra conventionally measured with SEM/EDS. An aluminium alloy and a hard material ceramics were analysed as representative examples. It is demonstrated that the combination of the three analytical methods: (1) SEM imaging for surface morphology characterisation; (2) electron-excited X-ray spectroscopy with its high spatial resolution for element analysis of inclusions or precipitates; and (3) X-ray fluorescence for the detection of elements with concentrations below 0.1 mass% considerably improves the performance of SEM/EDX analyses. KW - Scanning electron microscopy KW - Microanalysis KW - Energy-dispersive X-ray spectroscopy KW - X-ray fluorescence KW - Micro-XRF KW - Materials science PY - 2011 SN - 2043-0655 VL - 25 IS - 4 SP - 11 EP - 13 PB - Wiley CY - Chichester AN - OPUS4-23764 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Welzel, F. A1 - Grunewald, Thomas A1 - Beyer, M. A1 - Grätz, Rainer T1 - Mechanisch erzeugte Reib- und Schlagfunken im Vergleich N2 - Die funkenerzeugenden Prozesse der Reib- und Schlagfunken konnten über gezielte Betrachtungen und einen schmalen Bereich der Parameterbreite der jeweiligen Zündquelle verglichen werden. So zeigten Versuche bei einem Volumenanteil von c ≤ 10 % H2 und somit sehr kurzen Reibzeiten (t < 1,0 s) ähnliche Ergebnisse bezüglich der Funkenentstehung sowie der Zündwahrscheinlichkeiten. Durch die unterschiedlichen funkenerzeugenden Mechanismen werden Schlagfunken jedoch schneller und bei geringeren Schlagenergien bzw. bei deutlich geringeren Leistungsdichten erzeugt. In Wasserstoff/Luft-Atmosphären bis 10 % H2 sinkt mit geringer werdendem Wasserstoffanteil sowohl bei Kurzzeit-Reib- als auch bei Schlagvorgängen die Zündwahrscheinlichkeit. Bei Konzentrationen über 10 % H2 steigt nur bei Reibschlagvorgängen die Zündwahrscheinlichkeit. Dies liegt an der Zunahme des Einflusses der heißen Oberfläche bei gleichzeitig sinkender Oxidationsmöglichkeit der heißen Partikel durch die hohe Wärmeleitfähigkeit von Wasserstoff bedingt durch den verminderten Sauerstoffgehalt im Gemisch. Temperaturmessungen bestätigen trotz der verkürzten Reibzeit Temperaturen von über 400 °C, die zur Entstehung von Funken aus unlegiertem, ferritischem Stahl notwendig sind. Eine sinnvolle und praxisgerechte Bewertung der Zündwahrscheinlichkeiten erscheint für Schlagfunken über das Energiekriterium und für Reibfunken über das Leistungskriterium möglich. PY - 2011 SN - 0030-834X VL - 121 IS - 1 SP - 41 EP - 46 PB - Wirtschaftsverl. NW CY - Bremerhaven AN - OPUS4-23766 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiggenhauser, Herbert T1 - Automated NDE of Structures with Combined Methods T2 - International Symposium on Nondestructive Testing of Materials and Structures NDTMS-2011 CY - Istanbul, Turkey DA - 2011-05-15 PY - 2011 AN - OPUS4-23767 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Urs A1 - Malaga, Katarina T1 - Study on the applicaiton of anti-grafiti systems on natural stone and condrete T2 - Hydrophobe VI CY - Rome, Italy DA - 2011-05-12 PY - 2011 AN - OPUS4-23718 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Urs A1 - Malaga, Katarina T1 - Study on the application of anti-graffiti systems on natural stones and concrete N2 - The goal of this study was to find a correlation between cleaning efficacy of substrates protected with anti-graffiti systems (AGS) and their porosity, surface roughness, and composition as well as usability of the Technical Testing Guideline for Anti-Graffiti Systems (TP-AGS, issued by BASt) for natural stone and brick/clinker masonry. The results showed that the cleaning efficacy mainly depends on the porosity of the substrate and the type of AGS. Also, higher surface roughness contributed to a lower cleaning efficacy. The results showed also that concrete panels and cement joints in masonry represented the worst case. The color change of all substrate materials compared to concrete was mostly within acceptable limits. Gloss changes were significant for a number of substrates. In particular, several of the wax-treated low-porosity substrates exceeded the threshold value of 10. The limit of water vapor permeability of the AGS prescribed in the TP-AGS might be too high for natural stone substrates. In general, the TP-AGS is useful for the determination of the efficiency factor of anti-graffiti agents on various substrates. T2 - Hydrophobe VI - 6th International conference on water repellent treatment of building materials CY - Rome, Italy DA - 12.05.2011 KW - Anti-graffiti KW - Permanent KW - Sacrificial KW - Stones KW - Concrete KW - Cleaning efficiency PY - 2011 SN - 978-3-931681-99-9 SP - 167 EP - 180 PB - Aedificatio Publishers AN - OPUS4-23719 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thöns, Sebastian A1 - Rücker, Werner T1 - Risikobasierte Überwachungsverfahren zur Lebensdauerverlängerung von bestehenden und neuen Bauwerken T1 - Risk based condition monitoring for life cycle extension of structures N2 - Diese Veröffentlichung enthält Konzepte zur Lebensdauerverlängerung von Bauwerken auf der Grundlage der Tragwerkszuverlässigkeitstheorie. Es werden aktuelle Forschungsergebnisse aus nationalen und europäischen Forschungsvorhaben vorgestellt. Den Schwerpunkt bildet die Verwendung von Bauwerksüberwachungsdaten unter Berücksichtigung von Messunsicherheiten zur Bestimmung der Tragwerkszuverlässigkeit. Dazu wird ein neuer Ansatz zur Bestimmung der A-posteriori Messunsicherheit vorgestellt. Es wird gezeigt, aufgrund welcher Eigenschaften der verwendeten probabilistischen Modelle die Zuverlässigkeit im Grenzzustand der Ermüdung in Bezug auf eine Lebensdauerverlängerung beeinflusst werden kann. N2 - This paper contains approaches aiming at the life cycle extension of structures on the basis of the structural reliability theory. Actual research results are presented with the focusing on the utilisation of monitoring data for the structural reliability analysis. In this context a framework for the determination of the posterior measurement uncertainty applying Bayesian Updating the process equation based measurement uncertainty with the Observation based measurement uncertainty is introduced. The general concepts for the utilisation of monitoring data and inspection data for updating the structural reliability in the view of life cycle extension are outlined. The characteristics of monitoring data in the context of the structural reliability theory are shown in detail on the basis of an example. T2 - DVM-Tag 2011 - Bauteilzuverlässigkeit - Schäden und ihre Vermeidung CY - Berlin, Germany DA - 04.05.2011 KW - Lebensdauerverlängerung KW - Tragwerkszuverlässigkeit KW - Messunsicherheit KW - Bauwerksüberwachung KW - Life cycle extension KW - Structural reliability KW - Measurement uncertainty KW - Structural monitoring PY - 2011 SN - 0946-5987 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 678 SP - 1 EP - 10 AN - OPUS4-23720 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brauser, Stephan A1 - Kannengießer, Thomas T1 - Hydrogen absorption and diffusion in different welded duplex steels N2 - In this study, hydrogen absorption and diffusion were investigated for various high-alloyed ferritic-austenitic duplex steels. On account of the specific transformation and solidification behaviour, respectively, of duplex steels as compared to single-phase ferritic and austenitic steels, special conditions have to be considered concerning hydrogen absorption which may ultimately lead to microstructure-dependent hydrogen-assisted weld metal cracking. Hydrogen absorption during welding may occur via the shielding gas, moisture from the surroundings or via the welding filler material. As a contribution to the interpretation and prediction of hydrogen-induced cracking in welded duplex steels, the actual hydrogen absorption via the arc as well as the weld metal hydrogen diffusion was investigated for the first time in a duplex steel DS (1.4462), a super duplex steel SDS (1.4501) and in a lean duplex steel LDS (1.4162). Isothermal heat treatment using carrier gas hot extraction enabled quantification of the amounts of hydrogen trapped in the respective microstructure areas. The hydrogen diffusion coefficients were determined by analytical and numerical calculation. The total hydrogen concentrations and the diffusion coefficients were found to be nearly identical. Trapped hydrogen was however observed to be dependent on the material and on the microstructure condition. The influence of hydrogen on the mechano-technological properties of the weld metal was characterized with the help of tensile tests. In addition, the hydrogen embrittlement effect was detected in scanning electron microscopic analyses. KW - Absorption KW - Diffusion KW - Embrittlement KW - Duplex stainless steels KW - Hydrogen PY - 2011 SN - 0043-2288 SN - 1878-6669 VL - 55 IS - 5-6 SP - 26 EP - 36 PB - Springer CY - Oxford AN - OPUS4-23721 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schönbucher, A. A1 - Schälike, Stefan A1 - Vela-Wallenschus, Iris A1 - Wehrstedt, Klaus-Dieter T1 - CDF zur Simulation großer Kohlenwasserstoff/Peroxid-Poolfeuer T2 - 50. Tutzing-Symposium "CDF-Die Zukunft der Sicherheitstechnik? CY - Tutzing, Germany DA - 2011-05-22 PY - 2011 N1 - Geburtsname von Vela-Wallenschus, Iris: Vela, I. - Birth name of Vela-Wallenschus, Iris: Vela, I. AN - OPUS4-23722 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fedelich, Bernard A1 - Sievert, Rainer A1 - Schicker, Johannes A1 - Klingelhöffer, Hellmuth A1 - Skrotzki, Birgit T1 - Experimentelle Charakterisierung und Modellierung der thermomechanischen Ermüdung von Abgasturboladern aus Gusseisen T2 - Arbeitskreis Stoffgesetze, Universität Chemnitz CY - Chemnitz, Germany DA - 2011-06-10 PY - 2011 AN - OPUS4-23726 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Girard-Lauriault, Pierre-Luc A1 - Dietrich, Paul A1 - Gross, Thomas A1 - Unger, Wolfgang T1 - Quantitative Chemical Determination of Organic Layers using CDXPS: A Valid Experimental Procedure? T2 - Research Seminar - Max Planck Institute for Polymer Research CY - Mainz, Germany DA - 2011-05-19 PY - 2011 AN - OPUS4-23727 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geier, M. A1 - Eberstein, M. A1 - Partsch, U. A1 - Völkel, L. A1 - Böhme, R. A1 - Mann, Guido A1 - Bonse, Jörn A1 - Krüger, Jörg T1 - Impact of laser treatment on phosphoric acid coated multicrystalline silicon PV wafers T2 - 26th European Photovoltaic Solar Energy Conference CY - Hamburg, Germany DA - 2011-09-05 PY - 2011 AN - OPUS4-23750 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malitte, Hans-Joachim A1 - Redmer, Bernhard A1 - Beckmann, Jörg T1 - Strahlenschtuz beim ortsveränderlichen Umgang mit Betatrons bis 7,5 MeV T2 - DGZfP-Jahrestagung CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23751 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malitte, Hans-Joachim A1 - Sölter, B. A1 - Kaps, C. T1 - Strahlenschutzausbildung für die ZfP T2 - DGZfP-Jahrestagung CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23752 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sölter, B. A1 - Malitte, Hans-Joachim A1 - Reinhardt, E. T1 - ALARA in der ZfP T2 - DGZfP-Jahrestagung CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23753 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Min, Hyegeun A1 - Wettmarshausen, Sascha A1 - Friedrich, Jörg Florian A1 - Unger, Wolfgang T1 - A ToF-SIMS study of the deuterium-hydrogen exchange induced by ammonia plasma treatment of polyolefins N2 - ToF-SIMS has been used to study the surface functionalization of polypropylene and polyethylene samples by exposure to low-pressure ammonia plasma. Static secondary ion mass spectrometry is an appropriate tool to determine hydrogen isotopes as elements and in fragment ions with high sensitivity and selectivity. Specifically the exchange of hydrogen isotopes and the incorporation of N-containing moieties in the near-surface layer of the polyolefins have been studied in ND3 plasma experiments with conventional polypropylene (h-PP) and polyethylene (h-PE) and NH3 plasma experiments with deuterated polyethylene (d-PE). Considering the exchange of hydrogen between the plasma and the polymer surface studied by using deuterated ammonia and polyolefin samples the conclusion has been derived that polypropylene with its side chain methyl groups is more susceptible to hydrogen exchange reactions. For ND3 plasma treatment of polyethylene and polypropylene similar N-containing fragments were obtained and the measured semi-quantitative ToF-SIMS N-uptake data are rather similar. The observation of a wide range of characteristic mixed CkNlHmDn+ secondary fragment ions suggests complex and manifold reaction pathways at the polymer–plasma interface besides simple grafting of –ND2 or –NH2 moieties formed by ammonia fragmentation in the plasma. Finally, indications of an isotopic effect for hydrogen isotopes in the plasma process have been observed by comparison of ND3/h-PE results with those of NH3/d-PE. KW - ToF-SIMS KW - Hydrogen-deuterium exchange KW - Ammonia plasma treatment KW - Amine-functionalized polymer KW - Polyolefins PY - 2011 DO - https://doi.org/10.1039/c1ja10043b SN - 0267-9477 SN - 1364-5544 VL - 26 SP - 1157 EP - 1165 PB - Royal Society of Chemistry CY - London AN - OPUS4-23754 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Protz, Christian A1 - Völzke, Holger A1 - Zencker, Uwe A1 - Hagenow, Peter A1 - Grünewald, Heike T1 - Entwicklung neuer Prüfmethoden zur numerischen Beanspruchungsanalyse für die Fallprüfung an Stahlblechcontainern für das Endlager Konrad N2 - Die Bundesanstalt für Materialforschung und -prüfung (BAM) führt im Rahmen einer Verwaltungsvereinbarung mit dem Bundesamt für Strahlenschutz (BfS) Bauartprüfungen für Behältertypen durch, die für die Endlagerung von nicht wärmeentwickelnden radioaktiven Abfällen in das Endlager Konrad vorgesehen sind. Zur Erlangung einer Eignungsbestätigung einer Behälterbauart für das Endlager Konrad müssen die Antragssteller die Einhaltung der vom BfS festgelegten behälterspezifischen Anforderungen nachweisen. Zentrale Bestandteile der Bauartprüfung sind die Sicherheitsnachweise zur Behälterauslegung gegen mechanische Betriebs- und Störfallbelastungen sowie gegen thermische Störfallszenarien. Die Prüfanforderungen umfassen hierbei Stapeldruckprüfung, Hebeprüfung, Fallprüfung, thermische Prüfung (Brand), ggf. einschließlich Dichtheitsprüfung zum Nachweis der Einhaltung von Dichtheitsanforderungen. Neben der Nachweisführung mittels sogenannter Baumusterprüfungen oder Obertragbarkeitsbetrachtungen können die Nachweise alternativ mittels numerischer Sicherheitsnachweise erbracht werden, sofern deren hinreichende Verifikation nachgewiesen wird, Dies kann u. a. durch den Vergleich mit hinreichend gesicherten experimentellen Ergebnissen geschehen, Die hier vorgestellten Untersuchungen sind Teil des internen Forschungsprojektes ConDrop der BAM, das zum Ziel hat, erweiterte Prüfmethoden zur Fallprüfung an Stahlblechcontainern für das Endlager Konrad mittels numerischer Beanspruchungsanalyse zu entwickeln. Dazu soll ein Finite-Elemente-(FE)-Modell entwickelt und mit experimentellen Daten, die in Fallversuchen ermittelt werden, verifiziert werden. T2 - Jahrestagung Kerntechnik 2011 CY - Berlin, Deutschland DA - 17.05.2011 KW - Falltest KW - Stahlblechcontainer KW - Endlager Konrad KW - Numerische Beanspruchungsanalyse PY - 2011 IS - Session TS-19 / Paper 161 SP - 1 EP - 3 AN - OPUS4-23755 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weltschev, Margit T1 - Comparison between material parameters of polyethylene grades and the test performance behaviour of packaging for the transport of dangerous goods N2 - For the characterization and the comparison of polyethylene grades used for the manufacture of packaging and intermediate bulk container, the following parameters are required: melt flow rate (MFR), density (D), low-temperature notched impact strength, full notch creep test (FNCT) and increase of MFR by molecular degradation (resistance to oxidative degradation). The relationship between these material parameters determined on the basis of specimens prepared from compression-moulded sheets of polyethylene grades and the test behaviour of packaging has been investigated in several tests. The environmental stress crack resistance determined by FNCT represents the impacts from the stacking tests performed with standard liquid wetting solution (without pre-storage) and with normal butyl-acetate-saturated wetting solution (pre-storage with normal butyl acetate). Resistance to molecular degradation by the determination of MFR increase is related to the impacts in drop tests and stacking tests performed after pre-storage for 21 days with standard liquid 55% nitric acid at 40°C. The low-temperature impact strength is directly comparable with the impacts in drop tests at -18°C performed without pre-storage and after pre-storage with 55% nitric acid. A partly good relationship was found between the test results and the material parameters. Conditioning the design types with 55% nitric acid for 21 days causes an increase in the marginal drop heights of the design types in drop tests at -18°C when compared with design types without pre-storage. Post-cross-linking of the grades increases stiffness because of the acidic influence. KW - Dangerous goods packaging KW - Polyethylene grades KW - Material parameters KW - Design-type tests PY - 2011 DO - https://doi.org/10.1002/pts.940 SN - 0894-3214 VL - 24 IS - 6 SP - 361 EP - 371 PB - Wiley CY - Chichester, UK AN - OPUS4-23756 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Taffe, Alexander A1 - Kind, Thomas A1 - Stoppel, Markus A1 - Kurz, J.H. T1 - Bauwerkscanner zur automatisierten und kombinierten Anwendung zerstörungsfreier Prüfverfahren im Bauwesen N2 - Bereits seit vielen Jahren stehen Anwendern der zerstörungsfreien Prüfung im Bauwesen (ZfPBau) zuverlässige Geräte zur Untersuchung von Betonbauteilen zur Verfügung. Viele dieser Geräte zeichnen eine Messgröße in Bezug zum Messort auf und sind je nach Ausstattung in der Lage, die Ergebnisse in einem Koordinatensystem darzustellen. Doch erst die Kombination verschiedener ZfPBau-Verfahren an einer Messfläche erlaubt den maximalen Informationsgewinn über die innere Konstruktion von Stahlbeton- und Spannbetonbauteilen. In dem Beitrag wird ein Bauwerkscanner zur automatisierten und kombinierten Datenaufnahme beschrieben, der erstmals die Kombination von Radar, Ultraschall und Wirbelstrom mit Datenausgabe in einem einheitlichen Koordinatensystem ermöglicht. Dieser Scanner ist im Gegensatz zu früheren Systemen technikerbasiert und erlaubt im Bedarfsfall eine spätere detaillierte Auswertung durch ZfP-Spezialisten. Die Ergebnisse werden bildgebend in frei wählbaren Schnitten dargestellt, was bereits kurze Zeit nach der Messung auf der Baustelle möglich ist. Am Beispiel eines Brückenträgers wird gezeigt, wie der tatsächliche Spanngliedverlauf aus Messdaten ermittelt wird und dem angenommenen Verlauf gemäß Bestandsplan gegenübergestellt wird. Damit kann künftig eine Überprüfung von Bestandsplänen durchgeführt werden. Darüber hinaus könnten nicht vorhandene Bestandspläne rekonstruiert werden. Des Weiteren wird am gleichen Brückenträger gezeigt, wie sich ein echter Verpressfehler und im Unterschied dazu ein Luftspalt in einem Hüllrohr in Messdaten abbilden. An dem Beispiel wird deutlich, wie Ultraschallergebnisse in Kombination mit Phasenauswertung zur Formulierung von Verdachtsstellen für Verpressfehler eingesetzt werden können und welche Maßnahmen zur Verifizierung getroffen werden müssen. KW - Zerstörungsfreie Prüfung im Bauwesen KW - Bauen im Bestand KW - Brückenprüfung KW - Spanndrahtbruch KW - Remanenzmagnetismus KW - Automatisierung PY - 2011 DO - https://doi.org/10.1002/best.201100004 SN - 0005-9900 SN - 1437-1006 VL - 106 IS - 4 SP - 267 EP - 276 PB - Ernst CY - Berlin AN - OPUS4-23757 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brandes, E. A1 - Milde, Joachim A1 - Schröder, Volkmar T1 - Schwer entzündbare Gase und Dämpfe - Erweiterung der europäischen Norm EN 1839 N2 - Ab Januar 2011 dürfen nach der europäischen Richtlinie 2006/40/EG über Emissionen aus Klimaanlagen in Kraftfahrzeugen bei neuen EG-Typzulassungen die PKW-Klimaanlagen nur noch Kältemittel enthalten, deren Global Warnung Potential (GWP) kleiner 150 ist. Der vorgeschlagene Ersatzstoff für das bisher verwendete R-134a (1,1,1,2-Tetrafluorethan, GWP = 1430) ist 2,3,3,3-Tetrafluorpropen (R-1234yf; GWP = 4). Im Gegensatz zu R-134a, das bei Umgebungsbedingungen keinen Explosionsbereich aufweist, kann 2,3,3,3-Tetrafluorpropen bei Umgebungsbedingungen explosionsfähige Gemische mit Luft bilden. Die Neufassung der DIN EN 378-1, die 2008 in Kraft getreten ist, klassifiziert Kältemittel nach deren Brennbarkeit in drei Kategorien: nicht entzündbar, geringe Brennbarkeit, größere Brennbarkeit. International ist eine analoge Klassifizierung für Kältemittel in der ISO 817:2005 zu finden. Gase geringer Brennbarkeit' und Flüssigkeiten die keinen Flammpunkt nach Norm aufweisen, aber einen Explosionsbereich in Luft haben, werden zur Gruppe der so genannten schwer entzündbaren Gase und Dämpfe(Flüssigkeiten) zusammengefasst. Solche Gase werden unter anderem häufig als Kältemittel in Wärmepumpen und Klimaanlagen eingesetzt und werden daher in beträchtlichen Mengen in Verkehr gebracht. KW - Explosionsschutz KW - Sicherheitstechnische Kenngrößen KW - Nicht-atmosphärische Bedingungen PY - 2011 SN - 0030-834X VL - 121 IS - 1 SP - 16 EP - 20 PB - Wirtschaftsverl. NW CY - Bremerhaven AN - OPUS4-23710 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Korzen, Manfred ED - Wald, F. ED - Horová, K. ED - Jirku, J. T1 - Constitutive equations for structural steel subjected to fire - some remarks N2 - Although identified on the basis of so-called instationaiy creep-tests the constifrvtive model of Eurocode 3 (EN 1993-1-2, 2010) - hereinafter refened to as EC3 - represents a non-linear rateindependent relationship between stress and meclianical strain. I.e. the experimentally observed phenomenou of creep at constant stress but linear time varying temperature is described only through the temperature dependence of the material parameters characterizing the EC3 constitutive model. As a consequence some important phenomena cannot properly be described: E.g. creep or relaxation at constant temperature, creep or relaxation at non-monotonic temperature rates or sensitivity of the instationary creep process on the temperatme rate. T2 - International conference 'Applications of structural fire engineering' CY - Prague, Czech Republic DA - 29.04.2011 KW - Constitutive equation KW - Thermal strain KW - Steel KW - Fire KW - Creep PY - 2011 SN - 978-80-01-04798-9 SP - 79 EP - 83 AN - OPUS4-23711 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rohrmann, Rolf A1 - Thöns, Sebastian A1 - Rücker, Werner A1 - Bicker, S. A1 - Said, Samir A1 - Schmid, Wolfgang T1 - Structural investigations and monitoring results on a prototype of offshore wind turbines of multibrid M5000 series N2 - The concept and technical details of the implementation of the developed integrated monitoring system within the IMO-WIND project are presented. The tasks of the components of the system and its requirements are described. Selected results from the continuous monitoring during operation of the plant M5000_2 regarding the task design verification and dynamic structural analysis are given. T2 - DEWEK 2010 - 10th German wind energy conference CY - Bremen, Germany DA - 2010-11-17 KW - Integrated monitoring system KW - Offshore wind turbines KW - Design verification KW - Structural assessment KW - Limit values KW - Load transfer KW - Data management KW - Dynamic analysis KW - Rotor blades KW - Embedded sensors PY - 2011 IS - S03 SP - 1 EP - 5 PB - DEWI GmbH AN - OPUS4-23712 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ünal, Murat A1 - Klein, M. T1 - Development and design of repair and protection principles an a concrete repair mortar for the conservation of slab glass set in concrete from the 20th century. T2 - GLASSAC 11 3rd GLASSAC-Conference Glass Science in Art and Conservation CY - Wertheim, Germany DA - 2011-05-10 PY - 2011 AN - OPUS4-23713 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lohse, Volkmar A1 - Negendank, Detlef A1 - Thedens, M. T1 - Gaswarnsysteme für den Explosionsschutz - Anforderungen an Explosionsschutz, Messfunktion und funktionale Sicherheit N2 - Gaswarnsysteme, aber auch einfachere Gaswarngeräte und -anlagen, finden in der Industrie breite Anwendung zur Gefahrenabwehr in explosionsgefährdeten Bereichen im Sinne der Richtlinie 94/9/EG (ATEX 95). Hierfür werden meist Geräte zur Konzentrationsmessung von brennbaren Gasen mit einem Messbereich von 0 % bis 100 % der jeweiligen UEG eingesetzt. Ziel ist die rechtzeitige und zuverlässige Warnung vor unzulässig hohen Brenngaskonzentrationen unter Betriebsbedingungen. Sauerstoffmessgeräte, die bestimmungsgemäß für die Überwachung von Inertisierungsmaßnahmen verwendet werden, unterliegen ebenfalls den besonderen Anforderungen der ATEX-Richtlinie. KW - Gaswarnsysteme KW - Explosionsschutz KW - Messfunktion KW - Funktionale Sicherheit KW - ATEX PY - 2011 SN - 0030-834X VL - 121 IS - 1 SP - 30 EP - 33 PB - Wirtschaftsverl. NW CY - Bremerhaven AN - OPUS4-23716 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Urs A1 - Kargol, Marta A1 - Gardei, André A1 - Meng, Birgit T1 - Influence of blended cements on the performance of water repellent agents T2 - Hydrophobe VI CY - Rome, Italy DA - 2011-05-12 PY - 2011 AN - OPUS4-23717 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna T1 - Life in the Dust: Historic Samples and Modern Microbial Hitchhikers T2 - Symposium der Arbeitsgemeinschaft "Wissenschaft und Kunst" der Österreichischen Forschungsgemeinschaft am Institut für Architekturtheorie, Kunst und Kulturwissenschaften an der TU Graz CY - Graz, Austria DA - 2011-05-20 PY - 2011 AN - OPUS4-23728 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Braun, Ulrike A1 - Lorenz, Edelgard A1 - Maskos, Michael T1 - Investigation of the durability of poly(ether urethane) in water and air N2 - In this study some relevant aspects of the durability of an aromatic poly(ether urethanes) was investigated. Hydrolytic and oxidative treatments at increased temperatures were applied. The induced changes in the materials under investigation were characterised by complementary polymer characterisation methods, such as ATR-FTIR, DSC and mechanical testing. The thermal and hydrolytic treatment did not significantly affect the chemical composition of the materials. Changes can be observed in the microstructure of the materials. PY - 2011 DO - https://doi.org/10.5301/IJAO.2011.6408 SN - 0391-3988 VL - 34 IS - 2 SP - 129 EP - 133 PB - Wichtig Ed. CY - Milano [u.a.] AN - OPUS4-23729 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ünal, Murat A1 - Kühne, Hans-Carsten A1 - Kleine, M. A1 - Sander, C. T1 - Development and design of repair and protection principles and a concrete repair mortar for the conservation of slab glass set in concrete from the 20th century N2 - Main topics of the research project BEGLARES are the restoration of "dalle de verre" concrete Windows and the development of repair techniques and mortars. This project is executed in Cooperation between Glasmalerei Peters GmbH, the University of York and the BAM Federal Institute for Materials Research and Testing. It is funded by the Federal Ministry of Economics and Technology. The main mechanism of damages, the development of repair mortar and special test specimens are presented. T2 - GLASSAC 11 - 3rd GLASSAC Conference 'Glass science in art and conservation' CY - Wertheim, Bronnbach Monastery, Germany DA - 10.05.2011 KW - Concrete glazing KW - Carbonation KW - Maintenance planning KW - Actual state analysis PY - 2011 SN - 978-3-8396-0255-3 SP - 43 EP - 46 PB - Fraunhofer Verlag AN - OPUS4-23730 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Koch, Bernd A1 - Skrotzki, Birgit T1 - Strain controlled fatigue testing of the metastable Beta-titanium alloy Ti-6.8Mo-4.5Fe-1.5Al (Timetal LCB) N2 - The present work covers the mechanical behaviour of Timetal LCB under fatigue loading and utilizes transmission electron microscopy (TEM) to study the associated microstructural evolution. Fatigue specimens were taken out of LCB wire made for automotive suspension spring manufacturing in a solution treated as well as an additionally aged state. Uniaxial fatigue tests were carried out in total strain control with R = 0.1. Solution treated specimens tested at 3% and 4% maximum total strain showed a saturating force response, which differed from all other total strain controlled tests, and a distinct fracture behaviour. In addition, an increase of the dynamic Young's modulus is observed under these test conditions and in this material state. These findings are interpreted as a deformation induced precipitation of nanosize α- or ω-phase. In the aged state, the α-phase carries the major part of deformation work, noticeable by distinct α-substructures in fatigued specimen states. KW - Titanium alloys KW - Fatigue KW - Transmission electron microscopy KW - Fracture PY - 2011 DO - https://doi.org/10.1016/j.msea.2011.04.031 SN - 0921-5093 SN - 1873-4936 VL - 528 IS - 18 SP - 5999 EP - 6005 PB - Elsevier CY - Amsterdam AN - OPUS4-23731 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weidner, Steffen A1 - Falkenhagen, Jana T1 - MALDI-TOF Imaging Mass Spectrometry - an universal detector for copolymer chromatography T2 - ASMS-Conference on Mass Spectrometry CY - Denver, CO, USA DA - 2011-06-04 PY - 2011 AN - OPUS4-23732 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Huber, Alexandra A1 - Behnke, Thomas A1 - Resch-Genger, Ute A1 - Würth, Christian A1 - Jäger, Christian T1 - Quantitative solid-state NMR, absolute fluorescence, and absorption measurements of fluorescent nano- and microparticles T2 - Alpine Conference on solid-State NMR CY - Chamonix, France DA - 2011-09-11 PY - 2011 AN - OPUS4-23733 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter T1 - Combustion of peroxy-fuels T2 - ERCOFTAC Conference: Highly Resolved Experimental and Numerical Diagnostics for Turbulent Combustion (HRTC-1) CY - Rouen, France DA - 2011-05-25 PY - 2011 AN - OPUS4-23734 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Röhrich, J. A1 - Damerow, T. A1 - Hahn, W. A1 - Reinholz, Uwe A1 - Denker, A. A1 - Müller, U. T1 - A Tandetron as proton injector for the eye tumor therapy in Berlin T2 - 14th Int. Conf. on Ion Sources (ICIS11) CY - Giardini Naxos, Italy DA - 2011-09-12 PY - 2011 AN - OPUS4-23736 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Woydt, Mathias A1 - Scholz, Christian A1 - Spaltmann, Dirk T1 - Highly concentrated and low friction slip-rolling contacts through thin film coatings and/or alternative steels? T2 - STLE 66th Annual Meeting & Exhibition CY - Atlanta, GA, USA DA - 2011-05-15 PY - 2011 AN - OPUS4-23698 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Thomas A1 - Gradt, Thomas A1 - Theiler, Geraldine T1 - Tests of solid lubricants for cryogenic and vacuum environment T2 - STLE 66th Annual Meeting & Exibition CY - Atlanta, GA, USA DA - 2011-05-15 PY - 2011 AN - OPUS4-23699 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von der Ehe, Kerstin A1 - Jaunich, Matthias A1 - Wolff, Dietmar T1 - UHMW-PE - A shielding material with special properties influenced by radiation T2 - Jahrestagung Kerntechnik 2011 CY - Berlin, Germany DA - 2011-05-17 PY - 2011 AN - OPUS4-23700 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Merk, Virginia A1 - Kneipp, Janina T1 - Development and characterisation of new planar SERS sensors for detection of catalytic acitvity and other applications T2 - Molecular Plasmonics CY - Jena, Germany DA - 2011-05-19 PY - 2011 N1 - Geburtsname von Merk, Virginia: Joseph, V. - Birth name of Merk, Virginia: Joseph, V. AN - OPUS4-23701 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eslahian, Kyriakos-Alexandros A1 - Maskos, Michael T1 - Effect of Electrolyte Species and Concentration on the Soret Coefficient of Aqueous Dispersions observed by Thermal Field-Flow Fractionation T2 - 19th European Conference on Information Systems (ECIS) 2011 CY - Berlin, Germany DA - 2011-09-04 PY - 2011 AN - OPUS4-23702 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Noskov, Sergey A1 - Scherer, Christian A1 - Schupp, W. A1 - Maskos, Michael T1 - Determination of Hamaker constants of polymeric nanoparticles by asymmetrical flow field-flow fractionation T2 - European Colloid and Interface Society meeting 2011, CY - Berlin, Germany DA - 2011-09-04 PY - 2011 AN - OPUS4-23703 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Portella, Pedro Dolabella A1 - Rücker, Werner A1 - Trappe, Volker T1 - Offshore wind energy plants - problems and possible solutions T2 - Keynote paper, Wind energy Symposium, COTEQ 2011, 11a Conferencia de Tecnologia de Equipamentos ABENDI / ABCM CY - Ipojuca, Brazil DA - 2011-05-12 PY - 2011 AN - OPUS4-23704 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pentzien, Simone A1 - Conradi, Andrea A1 - Koter, Robert A1 - Krüger, Jörg ED - Engel, P. ED - Schirò, J. ED - Larsen, R. ED - Moussakova, E. ED - Kecskeméti, I. T1 - Cleaning of soiled paper model samples using short and ultrashort laser pulses N2 - Paper is one of the most important materials representing and witnessing human culture particularly as a carrier medium for text and image. As soiling hampers the reception of information, paper cleaning techniques are needed. Traditional mechanical and chemical cleaning methods are used by conservator-restorers. In some cases, a classical cleaning procedure of paper objects yields unsatisfactory results or a conventional treatment is even impossible. Especially, fragile paper objects cause problems due to mechanical instabilities. Laser cleaning as a non-contact method might be a way to overcome some of the limitations of classical cleaning techniques. Laser parameters have to be chosen to achieve removal of the soiling without influencing the artwork. Any immediate as well as long-term effects causing an irreversible change of the artwork have to be avoided. At present, most laser applications are found in stone and metal conservation, while laser treatment of complex organic materials like paper is still not fully developed for application in conservators' workshops. This contribution describes recent work of pulsed laser cleaning of soiled model samples. Pure cellulose, rag paper and wood-pulp paper were mechanically soiled with pulverized charcoal in a standardized procedure to make model samples representing essential characteristics of contaminated real-world artworks. Afterwards, model samples were cleaned using short and ultrashort laser pulses in the nanosecond and femtosecond time domain, respectively. An extensive analysis of the model samples after laser treatment using an optical microscope and a multi-spectral imaging system allows a comparison of the cleaning results obtained with both laser sources. T2 - Conference 'New Approaches to Book and Paper Conservation - Restoration' CY - Horn, Austria DA - 09.05.2011 KW - Laser cleaning KW - Ablation KW - Laser impact on surfaces KW - Paper KW - Femtosecond laser KW - Nanosecond laser PY - 2011 SN - 978-3-85028-518-6 SP - 519 EP - 532 PB - Verlag Berger, Horn CY - Vienna, Austria AN - OPUS4-23705 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Qiao, Linan A1 - Zencker, Uwe A1 - Musolff, André A1 - Komann, Steffen T1 - Dynamic finite element analyses of a spent fuel transport and storage cask with impact limiters by 9 meter drop tests N2 - The 9 meter drop onto an unyielding target is one of the important mechanical tests within the safety assessment of transport casks for radioactive material. In general, the cask is equipped with impact limiters to reduce the dynamic load on the cask body by absorbing a major part of the kinetic energy. The impact limiters are often made of wood or aluminium. In this study an elastic-plastic material model with volume change was used to describe the stress-strain behaviour of wood found in crush tests. For aluminium, an elastic-incremental plastic material model with Cowper-Symonds parameters for strain rate depending material hardening was used to model the adiabatic stress-strain relations measured at specimens at constant ambient temperature. Hereafter simulations with a sophisticated finite element model were carried out and compared with different drop tests. Four drop tests of a half-scale cask model equipped with wood and aluminium impact limiters with different drop positions were selected to investigate the impact limiter behaviour during a 9 meter drop test. All drop tests were simulated with the same FE mesh but under different boundary and initial conditions. T2 - SIMULIA Customer conference CY - Barcelona, Spain DA - 17.05.2011 KW - Cask KW - Drop test KW - Impact limiter KW - Wood KW - Aluminium KW - Dynamics PY - 2011 SP - 932 EP - 944 AN - OPUS4-23706 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Lehmann, Jens T1 - Korrosionsverhalten von Edelstahl-Rostfrei T2 - Metallbautechnisches Kolloquium - Verarbeitung von Edelstahl-Rostfrei CY - Bruchsal, Germany DA - 2011-05-25 PY - 2011 AN - OPUS4-23688 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lausch, Thomas A1 - Kannengießer, Thomas T1 - Diffusible Hydrogen Content depending on Welding and Cooling Parameters T2 - "Gemeinschaftsarbeitsausschuss NAS/NMP: Zerstörende Prüfung von Schweißverbindungen (DVS AG Q 4)" und des AG A 4.1 "Wasserstoffunterstützte Rissbildung" CY - Berlin, Germany DA - 2011-04-14 PY - 2011 AN - OPUS4-23690 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chen, Ji A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - Prediction of weld pool shape and influence of joint preparation angle for new gas metal arc welding processes T2 - 16th International Conference on the Joining of Materials JOM-16 & 7th International Conference on Education in Welding ICEW-7, Sankt Helene Centre CY - Tisvildeleje, Denmark DA - 2011-03-10 PY - 2011 AN - OPUS4-23691 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lausch, Thomas A1 - Kannengießer, Thomas T1 - Diffusible Hydrogen Content depending on Welding and Cooling Parameters T2 - Intermediate Meeting of the Technical Commission C-II (Arc welding and Filler Metals) of the International Institut of Welding (iiW) CY - Zoetermeer, Netherlands DA - 2011-03-15 PY - 2011 AN - OPUS4-23692 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gebhardt, Moritz Oliver A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Einlagiges Laser-MSG-Hybridschweißen von Rohren hoher Wandstärke und geringem Außendurchmesser T2 - 7. Deutsch-Niederlandische Lasertage Weser-Ems CY - Papenburg, Germany DA - 2011-05-11 PY - 2011 AN - OPUS4-23693 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schempp, Philipp A1 - Cross, C.E. A1 - Schwenk, Christopher A1 - Rethmeier, Michael T1 - Influence of weld metal grain size on weldability of aluminium 6082 T2 - IIW Intermediate Meeting of Commission IX CY - Zoetermeer, Netherlands DA - 2011-03-15 PY - 2011 AN - OPUS4-23694 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heinze, Christoph A1 - Schwenk, Christopher T1 - Einflüsse in der Schweißsimulation eines MAG-Schweißprozesses T2 - Workshop "Anwendungsnahe Schweißsimulation" CY - Berlin, Germany DA - 2011-05-19 PY - 2011 AN - OPUS4-23695 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Proske, Matthias A1 - Koch, Matthias A1 - Nehls, Irene T1 - Qualitativer Nachweis von Treatments auf Nachstreumittelgemischen mittels temperatur-Thermodesorptions-Gaschromatographie mit gekoppelter Massenspektrometrie T2 - Wissenschaftliches Meeting (BASt - Bundesanstalt für Straßenwesen) CY - Bergisch Gladbach, Germany DA - 2011-04-12 PY - 2011 AN - OPUS4-23696 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheid, Marc A1 - Krietsch, Arne T1 - Brand- und Explosionsgefahren bei der Handhabung nanokaliger Stäube T2 - Vortrag beim Treffen des Arbeitskreises "Erfahrungsaustausch Ex-Schutz-Dokument" des Fachausschuss Metall und Oberflächenbehandlung der DGUV/BG Holz und Metall CY - Alfeld, Germany DA - 2011-05-12 PY - 2011 AN - OPUS4-23697 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Merk, Virginia A1 - Kneipp, Janina T1 - Development and characterisation of new planar SERS sensors for detection of catalytic activity and other applications T2 - Spectroscopy - Detective in Science CY - Rostock, Germany DA - 2011-06-15 PY - 2011 N1 - Geburtsname von Merk, Virginia: Joseph, V. - Birth name of Merk, Virginia: Joseph, V. AN - OPUS4-23738 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krebs, Holger A1 - Schwarz, Silke T1 - Sprengstofflagerung unter Tage in Deutschland Vorschriften - Versuche - Entwicklungen T2 - Jahrestagung 2011 für Sicherheit im Bergbau CY - Bad Bleiberg, Austria DA - 2011-06-08 PY - 2011 AN - OPUS4-23743 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Füllbrandt, Marieke A1 - Purohit, Purv A1 - Schönhals, Andreas T1 - Dielectric and Thermal Investigation of Poly(vinyl acetate) adsorbed on Silica particles T2 - Deutsche Physikalische Gesellschaft (DPG) Spring Meeting 2011 CY - Dresden, Germany DA - 2011-03-13 PY - 2011 AN - OPUS4-23744 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lohrer, Christian T1 - Single ignition units T2 - Working Group Pyrotechnics at The European Commission CY - Brussels, Belgium DA - 2011-06-10 PY - 2011 AN - OPUS4-23745 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Protz, Christian A1 - Völzke, Holger A1 - Zencker, Uwe A1 - Hagenow, Peter A1 - Grünewald, Heike T1 - Entwicklung neuer Prüfmethoden zur numerischen Beanspruchungsanalyse für die Fallprüfung an Stahlblechcontainern Konrad T2 - Jahrestagung Kerntechnik 2011 CY - Berlin, Germany DA - 2011-05-17 PY - 2011 AN - OPUS4-23747 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Bohmeyer, W. T1 - Charakterisierung von Aushärtungsverlauf und Aushärtungszustand von reaktiven Harzen zur Composit-Herstellung in Labor und Fertigungsprozess (RTM, Prepreg-Autoklavenhärtung) T2 - Technologietag der Landesinitiative Nano- und Materialinnovationen Niedersachsen CY - Braunschweig, Germany DA - 2011-08-24 PY - 2011 AN - OPUS4-24288 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bothe, Martin A1 - Pretsch, Thorsten A1 - Khine, Y. A1 - Chaobin, H. T1 - Star-shaped poly(caprolactone-urethane) networks: Approach to modify shape memory properties T2 - Polymer Degradation Discussion Group, 29th PDDG Conference CY - Sestri Levante, Italy DA - 2011-09-05 PY - 2011 AN - OPUS4-24289 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pretsch, Thorsten T1 - Thermoplastic Poly(ester urethane): Durability, Triple-Shape Properties and one new Field of Application T2 - Polymer Degradation Discussion Group, 29th PDDG Conference CY - Sestri Levante, Italy DA - 2011-09-05 PY - 2011 AN - OPUS4-24290 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Marcano, Diana A1 - Mendez, P. A1 - Gibbs, J.W. T1 - Martensite fraction determination using cooling curve analysis N2 - This work presents a method of calculating the martensite fraction of an Fe-alloy, usingcooling curve analysis (CCA). It is based on a differential heat balance equation which takes intoaccount only convective exchange with the surroundings. By measuring a T(t) curve of an Fe-alloyand solving numerically the differential heat balance equation the martensite fraction can be calcu-lated. It is found that calculated martensite fraction using this methodology is comparable with resultsobtained using electron backscattering diffraction (EBDS). KW - Martensitic transformation KW - Cooling curve analysis PY - 2011 DO - https://doi.org/10.4028/www.scientific.net/SSP.172-174.221 SN - 1012-0394 SN - 1662-9779 SN - 0377-6883 VL - 172-174 SP - 221 EP - 226 PB - Trans Tech Publ. CY - Zürich AN - OPUS4-24291 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thöns, Sebastian A1 - Faber, M.H. A1 - Rücker, Werner ED - Faber, M.H. ED - Köhler, J. ED - Nishijima, K. T1 - On the utilization of monitoring data in an ultimate limit state reliability analysis N2 - This paper describes a structural reliability analysis utilizing monitoring data in the ultimate limit state with consideration of the uncertainties of the monitoring procedure. For this purpose the uncertainties of the monitoring data are modeled utilizing a new framework for the determination of measurement uncertainties. The approach is based on a process equation and Statistical models of observations for the derivation of a posterior measurement uncertainty by Bayesian updating. This facilitates the quantification of a measurement uncertainty using all available data of the measurement process. For the reliability analysis in the ultimate limit state, monitoring data can be utilized as a loading model Information and as proof loading, i.e. resistance model Information. Both approaches are discussed with generic examples and it is shown that the modeling of monitoring data in a reliability analysis can result in a reduction of uncertainties and as a consequence in the reduction of the probability of failure. Furthermore, the proof loading concept is developed further to account for the uncertain characteristic of proof loading due to the measurement uncertainties which is consistent with the framework for the determination of measurement uncertainties. These approaches and findings can be utilized for the assessment of structures for life cycle extension and the design of monitoring Systems. T2 - ICASP 11 - 11th International conference on applications of statistics and probability in civil engineering CY - Zurich, Switzerland DA - 01.08.2011 PY - 2011 SN - 978-0-415-66986-3 SP - 1762 EP - 1769 PB - Taylor & Francis CY - London AN - OPUS4-24292 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rohrmann, Rolf A1 - Said, Samir A1 - Schmid, Wolfgang A1 - Thöns, Sebastian A1 - Bicker, S. A1 - Rücker, Werner ED - De Roeck, G. ED - Degrande, G. ED - Lombaert, G. ED - Müller, G. T1 - Results from monitoring and assessment of offshore wind turbines N2 - To ensure a high operational reliability of offshore wind turbines (OWEC) with economically acceptable repair and maintenance efforts, comprehensive diagnosis and supervision concepts are required. Automatic monitoring Systems will be an essential part of such concepts. Because of the fact, that during Operation there will be static and dynamic interaction between the components ‘structure’, ‘machinery’ and ‘blades’ it is necessary to develop the monitoring techniques in an overall concept. These monitoring Systems are supposed to be applied for the design and testing as well as for the Operation and maintenance phases. The knowledge of the dynamic behavior of wind turbines is important both for the design and for a safe Operation. The available monitoring data from a period of three years, allow first conclusions on the long-term Operation of such Systems in terms of quality requirements to the instrumentation to the structure and the rotor blades T2 - EURODYN 2011 - 8th International conference on structural dynamics CY - Leuven, Belgium DA - 04.07.2011 KW - Integrated monitoring system KW - Offshore wind turbines KW - Structural assessment KW - Limit values KW - Measurement hardware KW - Data management KW - Embedded FBG sensors KW - Data analysis KW - Damage detection KW - Rotor blades PY - 2011 SN - 978-90-760-1931-4 IS - MS25 SP - 3450 EP - 3456 AN - OPUS4-24293 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kannengießer, Thomas A1 - Lausch, Thomas A1 - Kromm, Arne T1 - Effects of heat control on the stress build-up during high-strength steel welding under defined restraint conditions N2 - Realization and safe operation of modern welded structures are progressively requiring for base and filler materials to cope with continually increasing loads, Analyses with a view to crack prevention therefore need to accommodate particularly the structural design (restraint intensity) and the thermomechanical effects in terms of stresses introduced during welding, Against this background, multi-run welding experiments were carried out in an IRC - (Instrumented Restraint Cracking) Test under defined restraint intensity in order to examine the influence of heat control (preheating and interpass temperatures) on the weldinq-specific forces and stresses, The experiments revealed significant rises in the reaction force and stress after welding with increasing preheating and interpass temperature, Furthermore, various concepts for calculating the preheating temperature are discussed, It is demonstrated that the hitherto existing concepts for high-strength finegrained structural steels can lead to divergent results. KW - Cracking KW - Heat KW - High strength steels KW - Restraint KW - Stress KW - Testing PY - 2011 SN - 0043-2288 SN - 1878-6669 VL - 55 IS - 07/08 SP - 58 EP - 65 PB - Springer CY - Oxford AN - OPUS4-24294 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger ED - Robinson, W.H. ED - De Carvalho Campos, A.E. T1 - Wood protection by interfering with insect behavior: adequacy of laboratory test designs N2 - Standardized test methods by which the efficacies of conventional Chemical wood preservatives against insects determine their toxic effects against larvae of wood boring beetles or their feeding prevention by termites. Although alternative control strategies to the application of biocides exist, such as interference with insect behavior during mating or when searching for suitable breeding and feeding sites, their acceptance, too, depends on efficacy evaluation. This is why new test set ups are needed which take behavior modifying control strategies into account. This paper will demonstrate how new laboratory tests must be designed or how existing Standards can be altered to reliably interpret insect behavior including its successful manipulation in a standardized format. T2 - 7th ICUP - International conference on urban pests CY - Ouro Preto, Brazil DA - 07.08.2011 KW - Standardized tests KW - IPM KW - Efficacy evaluation KW - Wood borers KW - Termites PY - 2011 SP - 23 EP - 26 PB - Instituto Biológico CY - Sao Paulo, Brazil AN - OPUS4-24295 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Lexow, Jürgen A1 - Fellenberg, R. A1 - Krauß, O. T1 - Zwischenauditierung des BMBF-Förderprogramms 'Werkstoffinnovationen für Industrie und Gesellschaft . WING' N2 - Das Bundesministeriums für Bildung und Forschung (BMBF) fördert die Werkstofftechnologien und in Teilen die Nanotechnologie seit dem Jahr 2004 im Rahmen des Förderprogramms „Werkstoffinnovationen für Industrie und Gesellschaft - WING“. Die vorliegende Studie wurde im Auftrag des BMBF von der VDI Technologiezentrum GmbH und der BAM Bundesanstalt für Materialforschung und -prüfung erarbeitet. Sie stellt die Ergebnisse der Zwischenauditierung des WING-Programms dar, die im Kontext einer begleitenden Programmentwicklung nach fünf Jahren Laufzeit vorgesehen ist. Mit dem empirischen Teil des Zwischenaudits wurde im Jahr 2010 begonnen, so dass alle Projekte, deren Laufzeit vor dem 31.12.2009 begann, berücksichtigt werden konnten. Zweck des Zwischenaudits war es, die Wirkung der bisherigen Fördermaßnahmen seit Beginn des Programms anhand quantitativer und qualitativer Indikatoren zu erfassen und zu bewerten. Diese Wirkungsanalyse soll auch als Basis dienen, um in der weiteren Programmlaufzeit programmatische Ausrichtungen und prozessuale Abläufe bei Bedarf zu verbessern. KW - Innovation KW - Evaluation KW - Auditierung KW - WING KW - BMBF KW - Programm KW - Werkstoff PY - 2011 SP - 1 EP - 31 AN - OPUS4-24296 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ohm, Katrin A1 - Baer, Wolfram T1 - Einfluss der Verfahrenstechnik und der Werkstoffprüfung auf den im Zugversuch zu ermittelnden Verformbarkeitskennwert Agt von Betonstählen T2 - DVM-Tagung Werkstoffprüfung 2011 CY - Berlin, Germany DA - 2011-12-01 PY - 2011 AN - OPUS4-24248 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ostermann, Markus A1 - Berger, Achim A1 - Mans, C. A1 - Simons, C. A1 - Hanning, S. A1 - Janßen, A. A1 - Kreyenschmidt, M. T1 - Results and effects of homogeneity and stability studies carried out by X-ray fluorescence on the new reference material BAM-H010 N2 - The Federal Institute for materials research and testing (BAM)in cooperation with the Fachhochschule Münster has developed a new certified polymeric reference material, BAM-H010. The reference material consists of acrylonitrile–butadiene–styrene terpolymer (ABS) and has been doped with different contents of the elements Br, Cd, Cr, Hg and Pb. The monitoring of these elements is demanded in the EU directive 2002/95/EG, commonly referred to as RoHS. We have shown that the uncertainty contribution of the thermal long-term stability (ustability) is negligible compared to the contribution to the uncertainty caused by the method used for the characterization of the elemental content and the batch inhomogeneity (uhomogeneity). The stability of theABS material during exposure of the samples with hard X-radiation leads to a degradation of the ABS matrix with either long- or short-chain products. KW - Reference material KW - Plastic KW - RoHS KW - WEEE KW - X-ray fluorescence PY - 2011 DO - https://doi.org/10.1007/s00769-011-0806-x SN - 0949-1775 SN - 1432-0517 VL - 16 IS - 10 SP - 515 EP - 522 PB - Springer CY - Berlin AN - OPUS4-24249 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian A1 - Basan, Ricardo T1 - Micromecanics based failure analysis of laminates under off-axis loading N2 - The debonding of a fiber in a glass fiber / epoxy composite under transverse loading is studied. The stress field in the interface as well as the energy release rate are analysed for two fiber volume fractions. The circumferential propagation of an Interface crack starting at the center of a fiber which is located within a hexagonal fiber array is studied. The analysis is performed by a finite element Simulation under plane stress conditions. Two fiber volume fractions are considered, this is 30% and 70%. The stress distribution before and during crack propagation is calculated for different stages of the crack. The crack opens by dominating tensile stresses in the first phase while it closes when propagating along the interface. The total energy release rate as well as the mode I and mode II parts are calculated. In the first phase the crack is driven by an increasing mode I energy release rate, indicating an unstable crack propagation. Then the mode II energy release rate increases rapidly and dominates the debonding process while the mode I part decreases and finally vanishes. Subsequently also the mode II part decreases, indicating stable crack propagation. In the last phase the crack becomes unstable again due to a strongly increasing mode I energy release rate. During the debonding process a remarkable change the mode ratio takes place. The main features of the debonding process are similar for low and high fiber volume fraction. In case of the high fiber content, however, the mode I part is more pronounced and the maximum of the total energy release rate is shifted to lower crack angles. T2 - ICCM 18 - 18th International conference on composite materials CY - Jeju Island, Korea DA - 21.08.2011 KW - Composite Materials KW - Interface Crack KW - Failure Analysis KW - Adhesion PY - 2011 IS - T35-3-IF2032 SP - 1 EP - 6 AN - OPUS4-24252 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rakotondrajoa, Andrianiaina A1 - Reinholz, Uwe A1 - Buzanich, Günter A1 - Riesemeier, Heinrich T1 - Determination of the efficiency of a Silicon Drift detector (SDD) by Monte Carlo simulation T2 - Fachtagung Prozessnahe Röntgenanalytik PRORA CY - Berlin, Germany DA - 2011-11-24 PY - 2011 AN - OPUS4-24253 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schlichting, Joachim A1 - Maierhofer, Christiane A1 - Kreutzbruck, Marc T1 - Defect sizing by local excitation thermography N2 - In this article, we present a measurement procedure to gain information about depth and angle of surface braking cracks. The method is based on a local excitation with, e.g., a laser. The resulting surface temperature is recorded with an infrared camera. Based on this data, crack-caused anisotropies in the lateral heat flow can be detected and exploited to characterise the cracks. The experimental set-up is based on a Nd:YAG laser for heating and a high-speed infrared camera (InSb FPA, 3 to 5 µm) providing a frame rate of up to 500 Hz. Up to now, only qualitative information was gained from measurements of this type, whereas the local transient behaviour of temperature distribution provides also quantitative information of the crack parameters. Using FEM simulation we can show herein that it is possible to simultaneously resolve the angle and depth and, in particular, the depth of non-perpendicular cracks. KW - Surface braking cracks KW - Crack sizing KW - FEM KW - Laser thermography PY - 2011 DO - https://doi.org/10.3166/qirt.8.51-63 SN - 1768-6733 VL - 8 IS - 1 SP - 51 EP - 63 PB - Lavoisier CY - Cachan Cedex AN - OPUS4-24254 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Habel, Wolfgang A1 - Krebber, Katerina T1 - Fiber-optic sensor applications in civil and geotechnical engineering N2 - Different types of fiber-optic sensors based on glass or polymeric fibers are used to evaluate material behavior or to monitor the integrity and long-term stability of load-bearing structure components. Fiber-optic sensors have been established as a new and innovative measurement technology in very different fields, such as material science, civil engineering, light-weight structures, geotechnical areas as well as chemical and high-voltage substations. Very often, mechanical quantities such as deformation, strain or vibration are requested. However, measurement of chemical quantities in materials and structure components, such as pH value in steel reinforced concrete members also provides information about the integrity of concrete structures. A special fiber-optic chemical sensor for monitoring the alkaline state (pH value) of the cementitious matrix in steel-reinforced concrete structures with the purpose of early detection of corrosion-initiating factors is described. The paper presents the use of several fiber-optic sensor technologies in engineering. One example concerns the use of highly resolving concrete-embeddable fiber Fabry-Perot acoustic emission (AE) sensors for the assessment of the bearing behaviour of large concrete piles in existing foundations or during and after its installation. Another example concerns fiber Bragg grating (FBG) sensors attached to anchor steels (micro piles) to measure the strain distribution in loaded soil anchors. Polymer optical fibers (POF) can be — because of their high elasticity and high ultimate strain – well integrated into textiles to monitor their Deformation behaviour. Such 'intelligent' textiles are capable of monitoring displacement of soil or slopes, critical mechanical deformation in geotechnical structures (dikes, dams, and embankments) as well as in masonry structures during and after earthquakes. KW - Fiber-optic sensor KW - Monitoring KW - Earthquake damage assessment KW - Steel-reinforced structures KW - pH sensor KW - Geotextiles KW - Distributed sensor PY - 2011 DO - https://doi.org/10.1007/s13320-011-0011-x SN - 1674-9251 VL - 1 IS - 3 SP - 268 EP - 280 PB - Springer CY - Heidelberg ; Secaucus, NJ AN - OPUS4-24256 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dohse, Elmar A1 - Erthner, Thomas A1 - Schenk, Gottfried T1 - Einsatz von digitalen Filtern für die Ultraschallprüfung T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24308 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dohse, Elmar A1 - Ploigt, Roy A1 - Schenk, Gottfried T1 - Einsatz von digitalen Filtern für die Ultraschallprüfung T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24309 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Faust, R. A1 - Nauroozi, D. A1 - Bruhn, C. A1 - Koch, B. A1 - Kuhlich, Paul A1 - Piechotta, Christian A1 - Nehls, Irene T1 - (3,5,5,6,8,8-Hexamethyl-5,6,7,8-tetrahydronaphthalen-2-yl)methanol: a possible metabolite of the synthetic musk fragrance AHTN N2 - The title compound (AHTN-OH), C17H26O, was prepared in order to provide standard materials for the qualitative and quantitative analysis of environmental pollutants. The molecule possesses a chiral C atom, although the structure determination was performed on racemic material, expressed in the structure as disordered chiral sites. The asymmetric unit consists of four AHTN-OH molecules containing an hydroxy group and forming a tetrameric cyclic motif built up by four strong hydrogen bonds between these hydroxy groups and additionally by two weak C–H···π interactions. Furthermore, these tetramers are linked via very weak C–H···π interactions, forming chains along the c axis. PY - 2011 DO - https://doi.org/10.1107/S1600536811018009 SN - 1600-5368 VL - 67 SP - o1462-o1463, sup1-15 PB - Munksgaard CY - Copenhagen AN - OPUS4-24310 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hamann, F. A1 - Brehm, Robert A1 - Pauli, Jutta A1 - Grabolle, Markus A1 - Frank, W. A1 - Kaiser, W.A. A1 - Fischer, D. A1 - Resch-Genger, Ute A1 - Hilger, I. T1 - Controlled modulation of serum protein binding and biodistribution of asymmetric cyanine dyes by variation of the number of sulfonate groups N2 - To assess the suitability of asymmetric cyanine dyes for in vivo fluoro-optical molecular imaging, a comprehensive study on the influence of the number of negatively charged sulfonate groups governing the hydrophilicity of the DY-67x family of asymmetric cyanines was performed. Special attention was devoted to the plasma protein binding capacity and related pharmacokinetic properties. Four members of the DY-67x cyanine family composed of the same main chromophore, but substituted with a sequentially increasing number of sulfonate groups (n = 1−4; DY-675, DY-676, DY-677, DY-678, respectively), were incubated with plasma proteins dissolved in phosphate-buffered saline. Protein binding was assessed by absorption spectroscopy, gel electrophoresis, ultrafiltration, and dialysis. Distribution of dye in organs was studied by intraveneous injection of 62 nmol dye/kg body weight into mice (n = 12; up to 180 minutes postinjection) using whole-body near-infrared fluorescence imaging. Spectroscopic studies, gel electrophoresis, and dialysis demonstrated reduced protein binding with increasing number of sulfonate groups. The bovine serum albumin binding constant of the most hydrophobic dye, DY-675, is 18 times higher than that of the most hydrophilic fluorophore, DY-678. In vivo biodistribution analysis underlined a considerable influence of dye hydrophilicity on biodistribution and excretion pathways, with the more hydrophobic dyes, DY-675 and DY-676, accumulating in the liver, followed by strong fluorescence signals in bile and gut owing to accumulation in feces and comparatively hydrophilic DY-678-COOH accumulating in the bladder. Our results demonstrate the possibility of selectively controlling dye-protein interactions and, thus, biodistribution and excretion pathways via proper choice of the fluorophore's substitution pattern. This underlines the importance of structure-property relationships for fluorescent labels. Moreover, our data could provide the basis for the rationalization of future contrast agent developments. PY - 2011 DO - https://doi.org/10.2310/7290.2011.00005 SN - 1535-3508 SN - 1536-0121 VL - 10 IS - 4 SP - 258 EP - 269 PB - Decker CY - Hamilton, Ont. AN - OPUS4-24311 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Beyer, Katrin A1 - Kannengießer, Thomas A1 - Solórzano, E. T1 - In-situ measurement of hydrogen diffusion in steels using neutron radiography T2 - DIMAT 2011, 8th International Conference On Diffusion In Materials CY - Dijon, France DA - 2011-07-03 PY - 2011 AN - OPUS4-24312 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pirskawetz, Stephan A1 - Weise, Frank A1 - Plagge, R. A1 - Ruedrich, J. A1 - Rieffel, Y. T1 - An inter-disciplinary model project to develop an innovative winter covering system for the marble statuaries of the Schlossbrücke, Berlin (Germany) T2 - Jardins de Pierres Conservation of stone in Parks, Gardens and Cemeteries-International conference CY - Paris, France DA - 2011-06-22 PY - 2011 AN - OPUS4-24313 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann, Jens A1 - Burkert, Andreas T1 - Einsatz nichtrostender Stähle als Befestigungsmittel im Beton T2 - Befestigungsmittel im Stahlbetonbau - Planung - Werkstoffe - Zulassungen CY - Rostock, Germany DA - 2011-11-03 PY - 2011 AN - OPUS4-24314 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Lehmann, Jens A1 - Fischer, Joachim T1 - Korrosionsschäden bei Schweißnähten an CrNi-Stählen T2 - Landesfachtagung Schweißtechnik 2011, DVS-Landesverband Thüringen CY - Suhl, Germany DA - 2011-10-07 PY - 2011 AN - OPUS4-24315 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Lehmann, Jens A1 - Fischer, Joachim T1 - Korrosionsschäden an nichtrostenden Stählen T2 - Bauteilschädigung durch Korrosion CY - Cologne, Germany DA - 2011-11-30 PY - 2011 AN - OPUS4-24316 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Lehmann, Jens A1 - Fischer, Joachim T1 - Korrosionsverhalten nichtrostender Stähle - Einfluss von Legierungsgehalt, Verarbeitung und Oberflächenausführung T2 - Böhler-Welding Schweiss-Tagung CY - Giswil, Switzerland DA - 2011-11-03 PY - 2011 AN - OPUS4-24317 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kittler, Katrin A1 - Maul, Ronald A1 - Koch, Matthias A1 - Nehls, Irene T1 - Untersuchung der systematischen Verfügbarkeit des Cyanotoxins Cylindrospermopsin für Brassicaceae T2 - Deutscher Lebensmnittelchemikertag 2011 CY - Halle (Saale), Germany DA - 2011-09-12 PY - 2011 AN - OPUS4-24268 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Buchholz, Uwe A1 - Heidmann, G. A1 - Höhse, Marek A1 - Lothongkam, Chaiyaporn T1 - Fibre-optic sensors for early damage detection in plastic insulations of high-voltage facilities N2 - Fibre-optic sensors (FOS) have great potential as online damage detectors when integrated in HV accessories. Among their well-known use as temperature and strain sensors, there are some more opportunities of use, e. g. they can intimately be embedded in polymeric insulations of HV cable terminations and joints to detect and monitor partial discharges right at the location of their origin. Two FOS types for early PD detection were investigated: an embeddable fibre-optic acoustic sensor to measure acoustlc waves in polymeric insulations generated by PDs, and a fluorescent optical fibre to detect first optical effects during ionization processes in the insulation material. The paper descrlbes these methods, related monitoring Problems and shows first test results. T2 - ISH 2011 - 17th International symposium on high voltage engineering CY - Hannover, Germany DA - 22.08.2011 KW - Fibre optic sensors KW - Monitoring KW - Materials behavior KW - Early shrinkage of cement paste PY - 2011 SN - 978-3-8007-3364-4 SP - 2070 EP - 2075 PB - VDE Verlag GmbH AN - OPUS4-24270 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Schukar, Vivien ED - Ecke, W. ED - Peters, K.J. ED - Matikas, T.E. T1 - FOS standards and testing methods to validate fibre optic strain measurements N2 - Fiber optic sensors are increasingly used because of their outstanding performance or if special requirements avoid the application of conventional electrical sensors. The scientific background for optical fiber sensors is well developed; however, the characteristic of sensors applied in rather harsh environment are almost always different from characteristics determined in laboratory or before its installation. In order to achieve long-term stable function and reliable measurement data after application and under harsh environmental conditions, guidelines for characterization and specification of sensor components are needed as well as methodologies for testing the sensor performance must be developed. Performance tests carried out revealed that there are still some restrictions with respect to long-term reliable use: first, some sensor products available on the market are not very often appropriately characterized, described and validated; second, application procedures are not always defined due to a lack of understanding the micromechanical issues in the interface zone between sensor and measuring object. Application procedures and profound knowledge of materials behaviour are necessary to get results from the sensor that can be reliably used. The paper describes first guidelines to prove the quality of fiber optic strain sensors, a testing facility developed for unbiased tests and certification of surface-applied sensors as well as result from comparison of commercially available strain sensors. T2 - SPIE-Conference 'Smart sensor phenomena, technology, networks, and systems 2011' CY - San Diego, CA, USA DA - 06.03.2011 KW - Fiber optics KW - Strain sensor KW - Reliability KW - Durability KW - Creep KW - Application KW - Adhesive KW - Standards KW - Guideline KW - Testing PY - 2011 SN - 978-0-8194-8547-2 DO - https://doi.org/10.1117/12.881238 VL - 7982 SP - 79820O-1 EP - 79820O-12 AN - OPUS4-24271 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard A1 - Qian, H. A1 - Bismarck, A. A1 - Greenhalgh, E. A1 - Shaffer, M.S.P. T1 - Hierarchical Composites with Carbon Nanotube Grafted Fibres T2 - ECCM 13, 13th European Conference on Composite Materials CY - Stockholm, Sweden DA - 2011-06-02 PY - 2011 AN - OPUS4-24272 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Saathoff, F. A1 - Müller, Werner A1 - Witt, K. J. T1 - Neue Regelungen im Deponiebau N2 - Die neue Deponieverordnung fordert Zulassungen für Geokunststoffe, die in Deponiedichtungs­systemen eingesetzt werden. Diese gesetzliche Vorgabe führt dazu, dass in nationalen Regelwerken und Empfehlungen neue Vorgehensweisen verankert werden müssen. Zulassungsstelle ist die BAM Bundesanstalt für Materialforschung und -prüfung. Zuständig für die entsprechenden GDA Empfehlungen ist die UAG-Ak 5.1-6.1. Der Beitrag zeigt die Neuerungen, aber auch die Ausnahmeregelungen. Auf der Grundlage der Deponieverordnung hat die BAM einen Fach­beirat zusammengerufen, der verschiedene Arbeitsgruppen eingerichtet hat, um Zulassungsrichtlinie für Kunststoffdichtungsbahnen, Schutzschichten, Geotextilien zum Filtern und Trennen sowie Bewehrungsgitter aus Kunststoff zu erarbeiten oder zu aktualisieren. Die Zulassungsanforderungen lehnen sich wiederum eng an GDA- und EAG-Empfehlungen an. In dem Beitrag wird der Stand der Fachdiskussion in den Arbeitsgruppen erläutert. KW - Deponieverordnung KW - Geokunststoffe KW - GDA-Empfehlung KW - EDA-Empfehlung KW - BAM-Zulassung PY - 2011 SN - 0172-6145 SN - 1865-7362 SN - 2190-6653 IS - Sonderheft 2011 SP - 53 EP - 57 PB - VGE Verl. GmbH CY - Essen AN - OPUS4-24273 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tölle, Florian A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael ED - Halmoy, E. T1 - Residual stress reduction by beam defocusing in beam welding processes N2 - Residual stresses arising during welding, especially in high energy beam welding, can reach levels up to the material specific yield strength causing service life mitigating consequences through stress relaxation or stress corrosion cracking. A number of processes were developed like stress relief annealing or the low-stress-no-distortion-technique to reduce these stresses. But such methods are only applicable for wider welds and simple component geometries or they are cost-intensive. The method presented in this paper uses the welding beam after welding in a defocused mode for heating the material regions in a certain distance from the weld on both sides. With this process it is possible to decrease the stresses in small welds with high stress gradients without any contact surfaces or additional equipment. Dependent on the component geometry and on the laser power it is possible to use different parameters for this process. The adjustable process parameters are the radius and the power of the defocused beam and the transversal and longitudinal distances between the welding and the defocused beam. In this work the mechanism and the influence of the process parameters are investigated by FEM-simulation and a number of experiments on the ferritic steel S355J2+N with 5 mm thickness. The best experimental result presented in this paper shows a stress reduction of about 73 %. T2 - 13th NOLAMP conference - 13th Conference on laser materials processing in the nordic countries CY - Trondheim, Norway DA - 27.06.2011 KW - Residual stresses KW - Stress reduction KW - High energy beam welding KW - Post-weld heat treatment KW - Laser scanner optics PY - 2011 SN - 978-82-998664-1-5 SP - 235 EP - 245 AN - OPUS4-24274 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Raedel, Martina T1 - Gold mosaics - material composites and glass-chemical characteristics T2 - GLASSAC 11 - Tagung vom Frauenhofer ISC CY - Würzburg, Germany DA - 2011-05-10 PY - 2011 AN - OPUS4-24275 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lühl, Lars T1 - Overview of Micro-XRF and Micro-Xanes Sudies in Cultural Heritage T2 - Physical and Chemical Analytical Techniques in Cultural Heritage CY - Lisbon, Portugal DA - 2011-06-01 PY - 2011 AN - OPUS4-24276 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Masic, Admir A1 - Rabin, Ira A1 - Schütz, Roman A1 - Hahn, Oliver A1 - Fratzl, P. A1 - Masic, A. T1 - Polarized Raman Spectroscopy Approach for In-situ damage assessment of Collagen within Ancient manuscripts: The Temple Scroll Case T2 - Technart 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-24277 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ruhl, Aki Sebastian A1 - Saliwan Neumann, Romeo A1 - Kranzmann, Axel T1 - Microscopic 3-D Visualization of Corrosion Effects Formed under Carbon Capture and Storage (CCS) Conditions T2 - The European Corrosion Congress EUROCORR CY - Stockholm, Sweden DA - 2011-09-04 PY - 2011 AN - OPUS4-24299 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Maierhofer, Christiane A1 - Krankenhagen, Rainer A1 - Röllig, Mathias A1 - Schlichting, Joachim A1 - Schiller, M. A1 - Seidl, T. A1 - Mecke, R. A1 - Kalisch, U. A1 - Hennen, C. A1 - Meinhardt, J. T1 - Investigating historic masonry structures with a combination of active thermography and 3D laser scanner N2 - Methods for the combination (i. e. comparison and overlay) and data fusion (i. e. integration of all data in one data set, replacement of data) of active thermography and D laser scanner (light section method) have been developed. Systematic investigations for quantification of damage in historic structures are presented using both techniques. A case study shows that reproducible investigations at regular time intervals are very well suited for structural monitoring. KW - Active thermography KW - 3D laser scanner KW - Data fusion KW - Historic masonry KW - Monitoring PY - 2011 SN - 1768-6733 VL - 8 IS - 1 SP - 115 EP - 118 PB - Lavoisier CY - Cachan Cedex AN - OPUS4-24300 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ruhl, Aki Sebastian A1 - Göbel, Artur A1 - Bettge, Dirk A1 - Kranzmann, Axel T1 - Corrosion Effects on Steels for Carbon Capture and Storage (CCS) Applications T2 - The European Corrosion Congress EUROCORR CY - Stockholm, Sweden DA - 2011-09-04 PY - 2011 AN - OPUS4-24301 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - de Oliveira, Rui A1 - Marques, A.T. ED - Burnett, J.K. T1 - Optical fibre sensors for acoustic emission waves detection in composites N2 - In aeronautic and space engineering, safety is a major aspect. Periodical inspections by different non-destructive testing (NDT) techniques are performed to assess the structural integrity. The accuracy of such inspection is high ly dependent on the skills of the technician. To be more efficient automated procedures independent of human decision are needed. The costs for such inspections are also significant as they require immobilisation of aircrafts. Alternative on-line structural health monitoring (SHM) procedure capable to detect, acquire, and identify damage should permit important cost reductions but also safety increase from real-time damage assessment. The increasing application of composite materials in modern aircrafts and spacecrafts permits the development of such procedure from the embedment of sensors and actuators in the structure during manufacturing. PY - 2011 SN - 978-1-61209-960-6 IS - Chapter 1 SP - 1 EP - 28 PB - Nova Science Publishers, Inc. AN - OPUS4-24302 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ebell, Gino A1 - Burkert, Andreas A1 - Lehmann, Jens A1 - Mietz, Jürgen T1 - Korrosions- und Verbundverhalten verzinkter Betonstähle in Betonen mit chromatreduzierten Zementen N2 - Durch die Absenkung des Chromatgehalts der Zemente verändern sich die elektrochemischen Reaktionen von verzinkten Betonstählen in der Frischbetonphase. Mit Hilfe von elektrochemischen Messungen sowie Stabauszugsversuchen wurde an chromathaltigen und chromatreduzierten Zementen die Auswirkung des Chromats auf die Deckschichtbildung am Zink und auf das Verbundverhalten untersucht. Mit den Ergebnissen konnte eine Beeinträchtigung der Verbundzone als Folge der Chromatreduzierung für die Zementarten CEM I und CEM II nachgewiesen werden. Die Störung der Verbundzone ist in Bezug auf die sich ausbildende Porenstruktur als dauerhaft anzusehen. Die Auswirkungen auf das Verbundverhalten werden mit zunehmendem Betonalter weitgehend kompensiert. Die Ergebnisse der bezogenen Verbundspannung bei Verschiebewegen von 0,1 mm und 0,5 mm liegen trotz der Gefügestörung noch im Bereich der Erwartungswerte für den unverzinkten Betonstahl. Unter baupraktischen Gesichtspunkten muss die auftretende Gefügestörung hinsichtlich der Verbundspannung daher keine Berücksichtigung finden. KW - Verzinkt KW - Feuerverzinkt KW - Betonstahl KW - Verbund PY - 2011 DO - https://doi.org/10.1002/best.201100038 SN - 0005-9900 SN - 1437-1006 VL - 106 IS - 9 SP - 629 EP - 639 PB - Ernst CY - Berlin AN - OPUS4-24307 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Marinelli, F. A1 - Kuhlmann, S. I. A1 - Grell, E. A1 - Kunte, Hans-Jörg A1 - Ziegler, C. M. A1 - Faraldo-Gómez, J. D. T1 - Evidence for an allosteric mechanism of substrate release from membrane-transporter accessory binding proteins N2 - Numerous membrane importers rely on accessory water-soluble proteins to capture their substrates. These substrate-binding Proteins (SBP) have a strong affinity for their ligands; yet, Substrate release onto the low-affinity membrane transporter must occur for uptake to proceed. It is generally accepted that release is facilitated by the association of SBP and transporter, upon which the SBP adopts a conformation similar to the unliganded state, whose affinity is sufficiently reduced. Despite the appeal of this mechanism, however, direct supporting evidence is lacking. Here, we use experimental and theoretical methods to demonstrate that an allosteric mechanism of enhanced substrate release is indeed plausible. First, we report the atomic-resolution structure of APO TeaA, the SBP of the Na!-coupled ectoine TRAP transporter TeaBC from Halomonas elongata DSM2581T, and compare it with the substrate-bound structure previously reported. Conformational freeenergy landscape calculations based upon molecular Dynamics simulations are then used to dissect the mechanism that couples ectoine binding to structural change in TeaA. These insights allow us to design a triple mutation that biases TeaA toward apo-like conformations without directly perturbing the binding cleft, thus mimicking the influence of the membrane transporter. Calorimetric measurements demonstrate that the ectoine affinity of the conformationally biased triple mutant is 100-fold weaker than that of the wild type. By contrast, a control mutant predicted to be conformationally unbiased displays wild-type affinity. This work thus demonstrates that substrate release from SBPs onto their Membrane transporters can be facilitated by the latter through a mechanism of allosteric modulation of the former. KW - Binding thermodynamics KW - Periplasmic binding protein KW - Secondary transporter KW - ABC transporter KW - Replica-exchange metadynamics PY - 2011 DO - https://doi.org/10.1073/pnas.1112534108 SN - 0027-8424 SN - 1091-6490 VL - 108 IS - 49 SP - E1285 EP - E1292 AN - OPUS4-37681 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cabeza, Sandra A1 - Onorbe, Elvira A1 - Garces, Gerardo A1 - Perez, Pablo A1 - Klaus, Manuela A1 - Genzel, Christoph A1 - Adeva, Paloma T1 - The evolution of internal strain in Mg-Y-Zn alloys with a long period stacking ordered phase N2 - The load partition in Mg-Y-Zn system is studied by means of synchrotron diffraction. in-situ tensile tests disclose LPSO phases were for the first time proved to behave as an efficient reinforcement in Mg-Y-Zn alloys, therefore they could be treated as “short-fibre composite” for the modeling of mechanical behaviour. T2 - MECASENS CY - Grenoble, France DA - 16.09.2015 KW - Magnesium KW - LPSO KW - Synchrotron diffraction KW - Load partition PY - 2011 AN - OPUS4-38397 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Hedrich, Martina A1 - Czichos, Horst ED - Czichos, Horst ED - Saito, T. ED - Smith, L. T1 - The development of RM activities and application examples N2 - Activities for the development of reference materials started as early as 1906 at the US National Bureau of Standards (NBS). In 1912, the first iron and steel reference materials were certified for carbon content in Germany by the Royal Prussian Materials Testing Institute MPA, predecessor of BAM, the Federal Institute for Materials Research and Testing. KW - Reference materials PY - 2011 SN - 978-3-642-16640-2 SP - Chapter 3.7.7, 105 EP - 107 PB - Springer CY - Berlin, Heidelberg AN - OPUS4-32435 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Portius, P. A1 - Filippou, A.C. A1 - Schnakenburg, G. A1 - Davis, M. A1 - Wehrstedt, Klaus-Dieter T1 - Taming the silicon tetraazide beast N2 - Highly energetic silicon tetraazide 1 is synthesized safely in high yield and high purity. The compound is prepared as a solution in benzene which allows it to be handled safely. Stable Lewis base adducts of Si(N3)4 (e.g. 2) are also prepared by treatment of either Si(N3)4 or the di­sodium salt of hexaazidosilicate (3) with Lewis bases (2,2-bipyridine or 1,10-phenanthroline). Unlike Si(N3)4 the Lewis base adduct 2 is thermally stable and does not decompose below 265 °C. The decomposition is very energetic (ΔHd = -2.4 kJg-1) which means 2 and related Lewis base ­adducts could replace environmentally harmful Pb(N3)4 used as primary explosive. KW - Highly energetic silicon tetraazide KW - Lewis base adducts KW - Azides KW - Silicon KW - Energetic materials PY - 2011 DO - https://doi.org/10.1055/s-0030-1259150 SN - 1861-1958 VL - 1 SP - 0043 EP - 0043 PB - Thieme CY - Stuttgart AN - OPUS4-32352 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ballier, G. A1 - Mayer, K. A1 - Krause, Martin T1 - Ultraschallabbildung zur zerstörungsfreien Strukturbestimmung von Betonbauteilen mit Hilfe der "One-Way"-Wellengleichung N2 - Die ZfP versucht mit Hilfe von Messdaten, die sie aus z. B. einer Impuls-Echo-Messung gewinnt, Rückschlüsse auf die innere Struktur eines Objektes zu ziehen. Bei Betonbauteilen sollen im Besonderen Verpressfehler, die dann zur Korrosion und damit zur einer Beeinträchtigung der Standsicherheit und Dauerhaftigkeit des Konstruktion (z. B. einer Spannbetonbrücke) führen können, schnell und mit einer hohen Sicherheit aus den Messdaten lokalisiert werden. Das konventionellen SAFT oder FT-SAFT-Verfahren liefern in Verbindung mit einer Phasenauswertung einen schnellen und sicheren Hinweis darauf, dass ein Lufteinschluss/Defekt vorliegt. Darüber hinaus können jedoch Rückausbreitungs-Verfahren, wenn ein gutes Geschwindigkeitsprofil vorliegt, eine wesentlich bessere Lokalisierung des Defekts bieten als SAFT-Verfahren, jedoch mit dem Nachteil, dass sie sehr zeit- und rechenintensiv sind, vor allem im Dreidimensionalen. Als Mittelweg kann hierzu die "One-Way"-Methode dienen. Diese Methode verwendet Pseudo-Differential-Operatoren und ist sehr robust auch bei relativ groben Geschwindigkeitsprofilen. Sie wird an Beispielen aus der Bauwerkdiagnose mit den konventionellen Verfahren verglichen. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Ultraschallecho-Verfahren KW - Betonbauteile KW - Modellierung PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-328714 SN - 978-3-940283-33-7 SP - Poster 66, 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-32871 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jochems, Frank T1 - Anerkennung von Sachverständigen für Prüfungen an Tanks und MEGC zur Beförderung gefährlicher Güter im Seeverkehr auf Grundlage des IMDG-Code - Zahlen, Daten und Ausblick T2 - Erfa Tanks und BK-Schüttgut-Container 2011 CY - BAM Berlin DA - 2011-10-20 PY - 2011 AN - OPUS4-32918 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Ebell, Gino A1 - Burkert, Andreas A1 - Gehlen, C. A1 - Keßler, S. T1 - Validierung zerstörungsfreier Messmethoden zur zuverlässigen Erfassung von Bewehrungskorrosion (Schlussbericht) N2 - Determining a pore structure’s mechanical and chemical data on lime rendering exposed outdoors and including masonry in the laboratory, with regard to their behaviour on moisture transport and weathering was the objective. In search of clues for a dose-response relation - i.e. upon a connection between the emission rate of SO2 and NOx on one hand and the degree of damage to mainly plaster having a lime component on the other - it has been of interest to what extent their structural characteristics including pore space are modified and so consequently also physico-technical properties and chemical composition. For determining corresponding criteria, a widely diversified spectrum of test methods such as to obtain data concerning porosity and moisture transport, mechanical behaviour, and chemistry as well is available. A description of the manufacture of plate-shaped rendering specimens with lime putty, industrially hydrated lime and dolomitic hydrate (the last two also having a cement admixture) and also hydraulic lime as binding agents is included. First deposition velocity and absorption rate for SO2 were determined in laboratory tests on these materials in dry and moist states. After their exposure on outdoor racks at six locations in the Berlin region with differing SO2 atmospheric contents over at least 5 years, the samples of course show timedependent modifications of chemical and physical qualities which are especially reflected in the form of profiles of structure, strength and concentration, e.g. for sulphate. Local climatic differences, however, partly exert a greater influence on material than emissions. Similar investigations were performed on samples of comparable composition exposed 4 and 17 years. But the real surprise is furnished by the renderings’ behaviour depending upon orientation and upon height at a building. Since weathering behaviour and moisture Transport (absorption, storage, release) are directly interdependent, further criteria are necessary for a critical assessment of a plasters’ pore structure. Starting from sands, plasters were characterized. The structural parameters were lastly influenced by the respective contents of sand, binder and mixing water. These results and those gained from bricks naturally find their expression in masonry sections manufactured there from, and above all in their capillary and evaporative behaviours, and also when applying different test liquids. Summary and cited literature is given at the end of this report. KW - Potentialfeldmessung KW - Potential mapping KW - Korrosion KW - Stahlbeton KW - Betonstahl KW - Merkblatt B 3 PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-336229 SP - 1 EP - 92 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) / Technische Universität München AN - OPUS4-33622 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Oliver A1 - Christoph, Gabriele A1 - Kalbe, Ute A1 - Berger, Wolfgang T1 - Monitoring of PAH in aqueous samples - a comparison of different sample preparation techniques T2 - Environmental (Bio) Technologies CY - Gdansk, Poland DA - 2011-09-05 PY - 2011 AN - OPUS4-33661 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kannengießer, Thomas A1 - Kromm, Arne T1 - Characterising phase transformations of different LTT alloys and their effect on residual stresses and cold cracking N2 - Novel martensitic filler materials with specially adjusted martensite start temperatures (Ms) can counteract the cooling specific shrinkage due to expansion effects of the weld metal associated with phase transformations. That can be exploited to create compressive residual stresses in the weld and adjacent areas, i.e. beneficial for increasing fatigue strength. The Ms temperature is shifted via the chemical composition, mainly by the alloying elements nickel and chromium, resulting as well in different retained austenite contents. Investigations were made using different Low Transformation Temperature (LTT) alloys with varying nickel content. The resulting phase transformation temperatures were – for the first time – detected using high energy synchrotron diffraction and Single Sensor Differential Thermal Analysis (SS-DTA). Compared to angle dispersive diffraction, energy dispersive diffraction offers the possibility to measure residual stresses of the martensite and austenite phase parallel fast in one experiment up to depths of 100 µm. The residual stresses show significant distributions dependent on Ms temperature. The effect on the cold cracking behaviour of these alloys was investigated using the Tekken test. Results show that cold cracking can be avoided when appropriate contents of retained austenite are existent. KW - Austenite KW - Cold cracking KW - Martensite KW - Low themperature KW - Transformation PY - 2011 DO - https://doi.org/10.1007/BF03321286 SN - 0043-2288 VL - 55 IS - 3 SP - 48 EP - 56 PB - International Institute of Welding CY - France AN - OPUS4-38978 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Maierhofer, Christiane A1 - Kind, Thomas A1 - Köpp, Christian A1 - Helmerich, Rosemarie T1 - CHEF - Cultural heritage protection against flooding N2 - CHEF provides knowledge about flood protection of cultural heritage objects and directly supports the European Floods Directive by giving recommendations on how to assess the vulnerability of monuments. A comprehensive analysis of protective measures BEFORE, DURING and AFTER a flood has been carried out within the project, including technical and administrational measures. An overview of these measures is given, followed by recommendations on how to establish the most effective protective strategies. KW - Cultural heritage KW - Flood protection KW - Flood risks PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-385463 SP - 1 EP - 3 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-38546 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Merryweather, S. A1 - Zweifel, D. A1 - Woydt, Mathias ED - Franek, F. ED - Bartz, Wilfried J. ED - Pauschitz, A. ED - Vizintin, J. ED - Ciulli, E. ED - Crockett, R. T1 - Fuel economy of engine oils based on polyalkylene glycols N2 - The driver for automotive OEMs to work on alternative engine oils is the need for fuel economy and no adverse effect of the engine oil on the durability of particulate filters and catalysts. The alternative engine oils should for mid-term also comply with a positive environmental Profile. T2 - 3rd European Conference on Tribology and 4th Vienna International Conference on Nano-Technology CY - Vienna, Austria DA - 07.06.2011 KW - Biomotox KW - Head capacity KW - Fuel economy KW - Drain KW - Polyglycol KW - Polypropylene glycol KW - Polyalkylene glycol KW - Polybutylene glycol PY - 2011 SN - 978-3-901657-38-2 SP - 25 EP - 34 PB - MDH Media GesmbH CY - Wien AN - OPUS4-35671 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Sonderprüfverfahren für Verbundwerkstoffe T2 - Vortragsveranstaltung VDI-AK Kunststofftechnik, BV BB an der TU Berlin CY - Berlin, Deutschland DA - 2011-03-17 PY - 2011 AN - OPUS4-34456 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Qian, H. A1 - Kalinka, Gerhard A1 - Chan, K.L.A. A1 - Kazarian, S.G. A1 - Greenhalgh, E.S. A1 - Bismarck, A. A1 - Shaffer, M.S.P. T1 - Mapping local microstructure and mechanical performance around carbon nanotube grafted silica fibres: Methodologies for hierarchical composites N2 - The introduction of carbon nanotubes (CNTs) modifies bulk polymer properties, depending on intrinsic quality, dispersion, alignment, interfacial chemistry and mechanical properties of the nanofiller. These effects can be exploited to enhance the matrices of conventional microscale fibre-reinforced polymer composites, by using primary reinforcing fibres grafted with CNTs. This paper presents a methodology that combines atomic force microscopy, polarised Raman spectroscopy, and nanoindentation techniques, to study the distribution, alignment and orientation of CNTs in the vicinity of epoxy-embedded micrometre-scale silica fibres, as well as, the resulting local mechanical properties of the matrix. Raman maps of key features in the CNT spectra clearly show the CNT distribution and orientation, including a ‘parted’ morphology associated with long grafted CNTs. The hardness and indentation modulus of the epoxy matrix were improved locally by 28% and 24%, respectively, due to the reinforcing effects of CNTs. Moreover, a slower stress relaxation was observed in the epoxy region containing CNTs, which may be due to restricted molecular mobility of the matrix. The proposed methodology is likely to be relevant to further studies of nanocomposites and hierarchical composites. KW - Nanotubes KW - Silica fibres KW - Nano indentation KW - Mapping PY - 2011 DO - https://doi.org/10.1039/c1nr10497g SN - 2040-3364 SN - 2040-3372 VL - 3 IS - 11 SP - 4759 EP - 4767 PB - RSC Publ. CY - Cambridge AN - OPUS4-34718 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kind, Thomas T1 - GPR antenna array for the inspection of railway ballast N2 - A GPR antenna array was investigated for automated measurement of wave propagation velocity as a measure of the ballast quality. This goes beyond the regular application of conventional radar systems offering only qualitative structural information. The new approach provides a fast NDT method for the classification of ballast fouling. A main advantage of the multi-offset radar is that regular ballast digging for velocity evaluation can be avoided and travel time can be directly transformed into an equivalent depth by using the automatically evaluated velocity. Fast monitoring of ballast fouling condition can reduce maintenance cost significantly by supporting the works necessary for ballast cleaning and furthermore this method reduces interruption time for a better railway service. T2 - National Seminar & Exhibition on Non-Destructive Evaluation, NDE 2011 of the INDIAN SOCIETY FOR NONDESTRUCTIVE TESTING (ISNT) CY - Chennai, India DA - 08.12.2011 KW - Radar KW - Non-destructive testing KW - Railroad PY - 2011 AN - OPUS4-39811 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Silke A1 - Dette, Angelika A1 - Recknagel, Sebastian A1 - Jakubowski, Norbert T1 - Einsatz direkter Festprobentechniken gekoppelt an ICP OES und ICP-MS zur Charakterisierung keramischer Pulvermaterialien T2 - CANAS 2011 CY - Leipzig, Germany DA - 2011-03-13 PY - 2011 AN - OPUS4-23240 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wienold, Julia A1 - Recknagel, Sebastian A1 - Scharf, Holger A1 - Hoppe, Marion A1 - Michaelis, Matthias T1 - Elemental analysis of printed circuit boards considering the ROHS regulations N2 - The EU RoHS Directive (2002/95/EC of the European Parliament and of the Council) bans the placing of new electrical and electronic equipment containing more than agreed levels of lead, cadmium, mercury, hexavalent chromium, polybrominated biphenyl (PBB) and polybrominated diphenyl ether (PBDE) flame retardants on the EU market. It necessitates methods for the evaluation of RoHS compliance of assembled electronic equipment. In this study mounted printed circuit boards from personal computers were analyzed on their content of the three elements Cd, Pb and Hg which were limited by the EU RoHS directive. Main focus of the investigations was the influence of sample pre-treatment on the precision and reproducibility of the results. The sample preparation steps used were based on the guidelines given in EN 62321. Five different types of dissolution procedures were tested on different subsequent steps of sample treatment like cutting and milling. Elemental analysis was carried out using ICP–OES, XRF and CV–AFS (Hg). The results obtained showed that for decision-making with respect to RoHS compliance a size reduction of the material to be analyzed to particles ≤1.5 mm can already be sufficient. However, to ensure analytical results with relative standard deviations of less than 20%, as recommended by the EN 62321, a much larger effort for sample processing towards smaller particle sizes might be required which strongly depends on the mass fraction of the element under investigation. KW - RoHS KW - Printed circuit boards KW - Electrotechnical products KW - Elemental composition PY - 2011 DO - https://doi.org/10.1016/j.wasman.2010.10.002 SN - 0956-053X VL - 31 IS - 3 SP - 530 EP - 535 PB - Elsevier Ltd. CY - New York, NY AN - OPUS4-23986 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Niederleithinger, Ernst T1 - Optimierung und Erweiterung der Parallel-Seismik-Methode zur Bestimmung der Länge von Fundamentpfählen N2 - Das Parallel-Seismik-Verfahren dient vor allem der nachträglichen Langenmessung von Fundamentpfählen oder ähnlichen Elementen zur Gründung von Bauwerken. Eine solche Messung wird beispielsweise notwendig, wenn ein Gebäude verstärkt, erhöht oder anders als bisher genutzt werden soll, aber keine Unterlagen mehr über die Fundamente vorhanden sind. Das Messprinzip des schon seit einigen Jahrzehnten bekannten Verfahrens ist relativ einfach: Auf dem Pfahlkopf wird meist durch Hammerschlag eine Stoßwelle erzeugt, die durch den Pfahl nach unten lauft. Dabei wird Energie in den Boden abgegeben. Die abgestrahlten Wellen werden von Sensoren in einem parallel zum Pfahl hergestellten Bohrloch registriert. Aus den Laufzeiten lassen sich die materialspezifischen Wellengeschwindigkeiten im Pfahl und im Boden sowie die Pfahllange ermitteln. Bisher wurde meist ein sehr einfaches Verfahren zur Datenauswertung verwendet, das die Lange der Pfahle systematisch überschätzt. In der vorliegenden Dissertation wurden die mathematisch-physikalischen Grundlagen beleuchtet und durch Computersimulation die Wellenausbreitung in Pfahl und Boden genau untersucht. Weitere Simulationen klarten den Einfluss verschiedener Mess- und Strukturparameter, beispielsweise den Einfluss von Bodenschichtung oder Fehlstellen im Pfahl. So konnte geklärt werden, in welchen Fällen mit dem Parallel-Seismik-Verfahren gute Ergebnisse erzielt werden können (z. B. bei Fundamenten in Sand oder Ton) und wo es an seine Grenzen stößt (z. B. bei Gründung im Fels). Auf Basis dieser Ergebnisse entstand ein neuer mathematischer Formalismus zur Auswertung der Laufzeiten. In Verbindung mit einem Verfahren zur Dateninversion, d. h. der automatischen Anpassung der Unbekannten in den Gleichungen an die Messergebnisse, lassen sich sehr viel genauere Werte für die Pfahllange ermitteln als mit allen bisher publizierten Verfahren. Zudem kann man nun auch mit relativ großen Abstanden zwischen Bohrloch und Pfahl (2 - 3 m) arbeiten. Die Methode wurde an simulierten Daten ausführlich getestet. Die Messmethode und das neue Auswerteverfahren wurden in einer Reihe praktischer Anwendungen getestet – und dies fast immer erfolgreich. Nur in einem Fall komplizierter Fundamentgeometrie bei gleichzeitig sehr hoher Anforderung an die Genauigkeit war schon nach Simulationen klar, dass hier ein Einsatz nicht sinnvoll ist. Dafür zeigte es sich, dass auch die Lange von Pfahlwanden und Spundwanden ermittelt werden kann. Die Parallel-Seismik-Methode funktioniert als einziges verfugbares Verfahren zur Fundamentlangenermittlung zugleich in den meisten Bodenarten sowie an metallischen und nichtmetallischen Fundamenten und kommt ohne Kalibrierung aus. Sie ist nun sehr viel breiter einsetzbar und liefert sehr viel genauere Ergebnisse. Die Simulationen zeigten noch Potential für Erweiterungen, zum Beispiel durch den Einsatz spezieller Sensoren, die zusätzliche Wellentypen empfangen und unterscheiden können. N2 - The Parallel Seismic (PS) method is used for determination of the unknown or undocumented depth/length of foundations, mostly piles. PS is an established but rather not commonly used geophysical technique, which has been developed several decades ago. Currently, this method is standardized in France and included in the FHWA method catalog. The principle behind PS is quite simple: an impulse is generated on top of the pile by a hammer stroke, generating elastic waves (mainly compressional) traveling downward through the pile. Due to the high impedance contrast between pile and soil, the main part of the energy remains in the pile, but some is transmitted as guided waves into the surrounding soil. After reaching the pile toe, transmitted/diffracted waves of nearly spherical front are generated. These waves are recorded by sensors (hydrophones or geophones) in a nearby borehole. From the first arrival times registered at the sensors, the apparent wave velocity is calculated, which is different above the pile toe (pile velocity) and below (soil velocity). In the conventional data analysis, the pile length is estimated based on the intersection of the two travel time branches, leading to a systematic overestimation of the length of the pile. This thesis provides a systematic treatise of the mathematical and physical foundations of wave propagation in piles and soil. Extensive numerical simulations and parametric studies have been carried out to investigate the nature of the wave-field and influence of measurement and structural parameters. The results revealed the range of applicability of Parallel Seismic, but also some limitations, e. g. in the case of rock socketed foundations or piles containing flaws. A new formalism for data interpretation was developed based on the simulation results, which takes into account the soil layers and the borehole inclination. This novel data interpretation scheme was used in combination with different data inversion methods. A comparison of the results showed that the commonly used Levenberg-Marquardt type least squares approach gives sufficiently accurate estimations in most common scenarios. The VFSA (very fast simulated annealing) method offers some advantages (e. g. avoiding local minima under certain conditions) but is much more time consuming. The new interpretation method was successfully validated using several sets of simulated data. It proved to be not only more accurate than all other available methods, but also to extend the maximum allowable pileborehole distance to 2 – 3 m. Besides the numerical study, several field investigations have been carried out for the purpose of this study and also in the framework of real world projects. The foundation types included secant pile walls and sheet piles. The method performed successfully in all cases but one: a highly accurate determination of the connection of a T-shaped footing. In this particular case, the inapplicability of the method was concluded after some preliminary simulations, thus avoiding unnecessary costs to the client. Performing simulations prior to the actual testing is recommended in dealing with all non-standard cases. Today, Parallel Seismic is the only method applicable on metallic and non metallic foundations which can be used without calibration. It has the largest range of all borehole methods. T3 - BAM Dissertationsreihe - 70 KW - Parallel-Seismik KW - Fundament KW - Inversion KW - Bohrpfahl KW - Längenbestimmung PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-883 SN - 978-3-9813853-5-9 SN - 1613-4249 VL - 70 SP - 1 EP - 221 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-88 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Krause, Martin A1 - Borchardt, Kerstin A1 - Lange, Marco A1 - Behrens, Matthias A1 - Maack, Stefan A1 - Mielentz, Frank A1 - Milmann, Boris A1 - Schaurich, Dieter A1 - Wöstmann, Jens A1 - Hintzpeter, F. A1 - Sodeikat, C. T1 - Kosteneinsparung durch Anwendung zerstörungsfreier Prüfverfahren für Betonbauteile beim Bauen im Bestand N2 - In Zeiten knapper Kassen wird überall nach Wegen gesucht Kosten einzusparen. Im Bauwesen geht es dabei um Kosteneinsparungen ohne Reduktion der Sicherheit und Dauerhaftigkeit des Bauwerks. Beim Bauen im Bestand können mit einer zerstörungsfreien Prüfung von Bauwerken die Weiternutzung oder die erforderlichen Umbauten optimiert werden und so Kosten eingespart werden. KW - Zerstörungsfreie Prüfung KW - Bauen im Bestand KW - Radar KW - Ultraschallecho KW - Kosteneinsparung PY - 2011 SN - 978-3-8167-8611-5 VL - 101 SP - 1 EP - 95 PB - Fraunhofer IRB Verl. CY - Stuttgart ET - Abschlussbericht AN - OPUS4-26649 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosner, Martin A1 - Vogl, Jochen T1 - Three new offset Delta11B isotope reference materials for environmental boron isotope studies N2 - The isotopic composition of boron is a well established tool in various areas of Science and industry. Boron isotope compositions are typically reported as 5nB values which indicate the isotopic difference of a sample relative to the isotope reference material NIST SRM 951. A significant drawback of all of the available boron isotope reference materials is that none of them covers a natural boron isotope composition apart from NIST SRM 951. To fill this gap of required 5UB reference materials three new solution boric acid reference materials were produced, which cover 6096o of the natural boron isotope Variation (-20 to 40%oo B) of about 100%o. The new reference materials are certified for their B values and are commercially available through European Reference Materials® (http://wwrv.enn-cmi.org). The newly produced and certified boron isotope reference materials will allow straightforward method Validation and quality control of boron isotope data. T2 - International symposium on isotopes in hydrology, marine ecosystems and climate change studies CY - Monaco DA - 27.03.2011 KW - Boron KW - Boron isotope variations KW - Delta-scale KW - Stable isotopes KW - Isotope reference materials KW - Delta reference materials KW - Metrology in chemistry PY - 2011 SN - 978-92-0-135610-9 VL - 2 SP - 377 EP - 380 AN - OPUS4-31858 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vogl, Jochen A1 - Pritzkow, Wolfgang T1 - Isotope reference materials for present and future isotope research N2 - The variation of isotope abundance ratios is increasingly used to unravell natural and technical questions. In the past the investigation and interpretation of such variations was the field of a limited number of experts. With new upcoming techniques and research topics in the last decades, such as provenance and authenticity of food, the number of published isotope data strongly increased. The development of inductively coupled plasma mass spectrometers (ICPMS) from an instrument for simple quantitative analysis to highly sophisticated isotope abundance ratio machines influenced this process significantly. While in former times only experts in mass spectrometry were able to produce reproducible isotope data, nowadays many laboratories, never been in touch with mass spectrometry before, produce isotope data with an ICPMS. Especially for such user isotope reference materials (IRM) are indispensible to enable a reliable method validation. The fast development and the broad availability of ICPMS also lead to an expansion of the classical research areas and new elements are under investigation. Here all users require IRM to correct for mass fractionation or mass discrimination or at least to enable isotope data related to a common accepted basis. Despite this growing interest suitable IRM are still lacking for a number of isotope systems such as magnesium. PY - 2011 SN - 1471-8022 VL - 75 IS - 3 SP - 2098 PB - Mineralogical Society of Great Britain and Ireland CY - London AN - OPUS4-32683 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dalitz, F. A1 - Maiwald, Michael A1 - Guthausen, G. T1 - On-line NMR Spectroscopy of Technical Samples - Considerations of the Sample Residence Time T2 - 2nd European Conference on Process Analytics and Control Technology CY - Glasgow, Scotland DA - 2011-04-27 PY - 2011 AN - OPUS4-23665 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael T1 - Technologie-Roadmap, "Prozess-Sensoren 2015+", Vision oder Mission? T2 - MSR-Anwendertreffen Leipziger Messe CY - Leipzig, Germany DA - 2011-01-26 PY - 2011 AN - OPUS4-23091 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael A1 - Petzoldt, Martin A1 - Dalitz, F. A1 - Vargas, M. A1 - Steiwand, A. A1 - Guthausen, G. T1 - Prozesskontrolle mittels MR-NMR: Erste Ergebnisse T2 - Doktorandentagung Attendorn CY - Attendorn, Germany DA - 2011-02-27 PY - 2011 AN - OPUS4-23293 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael T1 - Analytische Methoden für das Polymorphiescreening in der pharmazeutischen Entwicklung T2 - Abschlussvortrag, Doktorandenseminar Attendorn CY - Attendorn, Germany DA - 2011-02-27 PY - 2011 AN - OPUS4-23292 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dalitz, F. A1 - Vargas, M. A1 - Petzoldt, Martin A1 - Maiwald, Michael A1 - Guthausen, G. T1 - Prozesskontrolle mittels MR-NMR: Erste Ergebnisse T2 - Anakon 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23400 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael ED - Gerlach, G. ED - Schütze, A. T1 - Anforderungen an Sensoren für die chemische Verfahrenstechnik N2 - Eine stets optimale Nutzung von Anlagen, Rohstoffen und Energie in Verbindung mit einer guten Prozessführung sind die wichtigsten Voraussetzungen für globale Wettbewerbsvorteile der Chemisch Pharmazeutischen Industrie und für die Branchen Energieerzeugung, Petrochemie, Nahrungsmittel, Papier- und Zellstoff oder Wasserversorgung. Überlegene Verfahren erfordern die fortwährende Kontrolle der geforderten Produktqualität, ihre präventive Sicherstellung und eine ständige Verbesserung des Wissens über den Prozess. Sensoren helfen dabei, alle wichtigen Messgrößen an kritischen Stellen transparent zu machen. Sie sind die 'Sinnesorgane der Prozessleittechnik' für automatisierte Verfahren. Allein aufgrund stetig wachsender Anforderungen an Sensoren ergibt sich für viele Messaufgaben die Notwendigkeit einer ständigen Verbesserung der Sensoren. Für völlig neue Aufgaben müssen jedoch neue Messprinzipien gefunden werden, weil heute noch keine Sensor-Technologie existiert oder die wachsenden Anforderungen nicht mehr allein durch Weiterentwicklung bestehender Technologien erfüllt werden können. Ende 2009 wurden Anforderungen und Wege für die konsequente Weiterentwicklung und Verbesserung von Prozess-Sensoren aus Anwendersicht aufgeschrieben. Das Projekt wurde von NAMUR und GMA initiiert und gemeinsam mit Industrieanwendern und Geräteherstellern als Technologie-Roadmap 'Prozess-Sensoren 2015+' veröffentlicht. Was ist aus den Wünschen seither geworden? Wie kann die Umsetzung dieser Entwicklungsziele von den Geräteherstellern wirtschaftlich und marktgängig erfolgen? Wie werden neuartige Forschungsziele mit der angemessenen Forschungsförderung am besten vorangebracht? T2 - 10. Dresdner Sensor-Symposium CY - Dresden, Germany DA - 05.12.2011 PY - 2011 SN - 978-3-942710-53-4 DO - https://doi.org/10.5162/10dss2011/6.1 N1 - Serientitel: Dresdner Beiträge zur Sensorik – Series title: Dresdner Beiträge zur Sensorik VL - 43 SP - 93 EP - 98 PB - TUDpress, Verlag der Wissenschaften GmbH AN - OPUS4-26242 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rosner, Martin A1 - Pritzkow, Wolfgang A1 - Vogl, Jochen A1 - Voerkelius, S. T1 - Development and validation of a method to determine the boron isotopic composition of crop plants N2 - We present a comprehensive chemical and mass spectrometric method to determine boron isotopic compositions of plant tissue. The method including dry ashing, a three-step ion chromatographic boron–matrix separation, and 11B/10B isotope ratio determinations using the Cs2BO2+ graphite technique has been validated using certified reference and quality control materials. The developed method is capable to determine δ11B values in plant tissue down to boron concentrations of 1 mg/kg with an expanded uncertainty of ≤1.7‰ (k = 2). The determined δ11B values reveal an enormous isotopic range of boron in plant tissues covering three-quarters of the natural terrestrial occurring variation in the boron isotopic composition. As the local environment and anthropogenic activity mainly control the boron intake of plants, the boron isotopic composition of plants can be used for food provenance studies. KW - Boron isotope variations KW - Delta-scale KW - Stable isotopes KW - Isotope reference materials KW - Provenance KW - Authenticity PY - 2011 DO - https://doi.org/10.1021/ac102836h SN - 0003-2700 SN - 1520-6882 VL - 83 IS - 7 SP - 2562 EP - 2568 PB - American Chemical Society CY - Washington, DC AN - OPUS4-23495 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Recknagel, Sebastian A1 - Kipphardt, Heinrich A1 - Lange, Britta A1 - Hoppe, Marion T1 - Traceable analysis of impurities in metallic reference materials using GD-MS N2 - The traceabiiity requirements for certification analyses of reference materials are much more stringent than for routine analysis, where certified matrix reference materials (CRM) can be used for calibration and to establish traceabiiity. Although the ISO-Guides related to CRM production and certification are not fully clear concerning calibration, many established CRM-producers do not accept matrix-CRMs for calibration in case of certification analyses, e.g. to avoid circular reasoning. These requirements limit the methods used for certification to those that can be calibrated using Standards of known high purity and stoichiometry or mixtures of such Standards. Powerful solid sampling techniques such as glow discharge mass spectrometry (GD-MS) or spark-optical emission spectrometry (SOES), where usually compact CRMs are used for calibration, seem not be applicable for certification analyses. Especially GD-MS is a powerful tool for trace element determination of solid samples. Beside metallic impurities the use of specific gas mixtures enables also the determination of interesting nonmetallic impurities such as sulfur and phosphorus. Within BAM a calibration approach, was developed which enables to use mixtures of Standards of known high purity and stoichiometry also for GD-MS. Analogue to matrix adaption in solution based techniques, the calibration approach is based on doped pressed powder pellets. Approach and application on the certification analyses of copper and Steel CRMs are presented. T2 - CETAS 2011 - 8th International workshop on progress in analytical chemistry & materials characterisation in the steel and metal industries CY - Luxembourg, Luxembourg DA - 17.05.2011 PY - 2011 IS - OC53 SP - 361 EP - 365 AN - OPUS4-23762 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Recknagel, Sebastian A1 - Kipphardt, Heinrich A1 - Lange, Britta A1 - Hoppe, Marion A1 - Gusarova, Tamara T1 - Traceable Analysis of Impurities in Metallic Reference Materials using GD-MS T2 - CETAS 2011 - Progress in Analytical Chemistry & Materials Characterisation in the Steel and Metals Industries CY - Luxembourg City, Luxembourg DA - 2011-05-17 PY - 2011 AN - OPUS4-23807 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Silke A1 - Dette, Angelika A1 - Meckelburg, Angela A1 - Recknagel, Sebastian A1 - Jakubowski, Norbert T1 - Einsatz direkter Festprobentechniken gekoppelt an ICP OES und ICP-MS zur Spurenelementanalyse in und Zertifizierung von Referenzmaterialien T2 - 16. Tagung Festkörperanalytik CY - Vienna, Austria DA - 2011-07-04 PY - 2011 AN - OPUS4-23814 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Sabine A1 - Niederleithinger, Ernst A1 - Krause, Martin A1 - Bohlen, T. T1 - Anwendung der Reverse-Time Migration auf Ultraschallmessungen an Beton in der zerstörungsfreien Prüfung T2 - Tagung der Deutschen Geophysikalischen Gesellschaft 2011 CY - Cologne, Germany DA - 2011-02-21 PY - 2011 AN - OPUS4-23333 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosner, Martin A1 - Vogl, Jochen T1 - Three new offset delta 11 B isotope reference materials for environmental boron isotope studies T2 - IAEA 2011 - "International Symposium on Isotopes in Hydrology, Marine Ecosystems, and Climate Change Studies" CY - Monaco DA - 2011-03-27 PY - 2011 AN - OPUS4-23815 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogl, Jochen A1 - Koenig, Maren A1 - Paz, B. A1 - Pritzkow, Wolfgang T1 - An alternative lead-matrix-separation procedure exemplarily shown for lead isotope analysis in the Trojan silver artefacts T2 - Technart 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-23818 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ballhause, Tony A1 - Niederleithinger, Ernst A1 - Wunderlich, Carolin T1 - MIIC-Monitoring und Imaging auf Grundlage interferometrischer Konzepte T2 - Tagung der Deutschen Geophysikalischen Gesellschaft 2011 CY - Cologne, Germany DA - 2011-02-21 PY - 2011 AN - OPUS4-23327 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosner, Martin A1 - Vogl, Jochen T1 - New offset delta 11 B isotope reference materials for geochemical and environmental boron isotope studies T2 - Goldschmidt Tagung 2011 CY - Prague, Czech Republic DA - 2011-08-14 PY - 2011 AN - OPUS4-23817 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rosner, Martin A1 - Vogl, Jochen T1 - New offset Delta11B isotope reference materials for geochemical and environmental boron isotope studies N2 - The isotopic composition of boron is a well established tool in various areas of Science and industries. Boron isotope compositions are typically reported as 6"B values which indicate the isotopic difference of a sample relative to the internationally accepted isotope reference material NIST SRM 951. A significant drawback of all of the available boron isotope reference materials is that non covers a natural boron isotope composition apart from NIST SRM 951. PY - 2011 SN - 1471-8022 VL - 75 IS - 3 SP - 1755 PB - Mineralogical Society of Great Britain and Ireland CY - London AN - OPUS4-32684 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst A1 - Wunderlich, Carolin T1 - Evaluation of temperature influence on ultrasound velocity in concrete by coda wave interferometry T2 - International Symposium on Nondestructive Testing of Materials and Structures, NDTMS-2011 CY - Istanbul, Turkey DA - 2011-05-15 PY - 2011 AN - OPUS4-24111 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maack, Stefan A1 - Spies, M. A1 - Hillemeier, B. T1 - 3D Schallfeldcharakterisierung niederfrequenter Ultraschall-Prüfköpfe in Beton - Experimentelle Untersuchungen und Simulation T2 - DGZfP Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24765 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogl, Jochen A1 - Pritzkow, Wolfgang T1 - Isotope reference materials for present and future isotope research T2 - Goldschmidt 2011 CY - Prague, Czech Republic DA - 2011-08-14 PY - 2011 AN - OPUS4-24109 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rigo, E. A1 - Rosner, Martin A1 - Vogl, Jochen T1 - Herkunftsbestimmung von Kalken T2 - Tagung Bauchemie 2011 CY - Hamburg, Germany DA - 2011-10-06 PY - 2011 AN - OPUS4-25919 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogl, Jochen A1 - Rigo, E. A1 - Rosner, Martin T1 - Herkunftsbestimmung von Kalken T2 - GDCh Tagung Bauchemie 2011 CY - Hamburg, Germany DA - 2011-10-06 PY - 2011 AN - OPUS4-25952 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Matschat, Ralf A1 - Dette, Angelika A1 - Richter, Silke A1 - Recknagel, Sebastian A1 - Barth, P. T1 - Certification of a boron carbide powder reference material for chemical analysis N2 - The certification of a boron carbide reference material for chemical composition is described. The mass fractions of 16 elements and two boron species are certified in an international interlaboratory comparison with 35 participating laboratories from six different countries. Beside chemical characterization the certification process includes homogeneity and stability testing of the candidate material boron carbide (type F360, 305M422). Details of the analytical methods used for chemical characterization and of the calculation of the uncertainties of the certified mass fractions are given. The new reference material ERM®-ED102 with certified mass fractions of 18 parameters (elements and species) and of the amount fraction of the isotope 10B is a valuable tool for laboratories working in the field of advanced ceramic materials analysis to improve their analytical results. KW - Boron carbide KW - Certified reference material KW - ERM KW - Certification PY - 2011 DO - https://doi.org/10.1111/j.1551-2916.2011.04657.x SN - 0002-7820 SN - 1551-2916 VL - 94 IS - 11 SP - 4009 EP - 4016 PB - Blackwell Publishing CY - Malden AN - OPUS4-24967 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Vogl, Jochen T1 - Diane Beauchemin and Dwight E. Matthews (Eds.): The encyclopedia of mass spectrometry, Volume 5: Elemental and isotope ratio mass spectrometry (Book Review) N2 - The encyclopedia of mass spectrometry, Volume 5: Elemental and isotope ratio mass spectrometry covers the subject almost entirely and serves as a reference work with links to specialist literature if more details are required. Therefore, this book can be recommended to all beginners, students, and experts working in this broad field. KW - Elemental mass spectrometry KW - Isotope ratio mass spectrometry PY - 2011 DO - https://doi.org/10.1007/s00216-011-5106-0 SN - 1618-2642 SN - 1618-2650 VL - 401 IS - 2 SP - 573 EP - 574 PB - Springer CY - Berlin AN - OPUS4-24089 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Recknagel, Sebastian A1 - Reeb, P. A1 - Schlothmann, B.-J. T1 - Referenzmaterialien in der Eisen- und Stahlindustrie N2 - Die regelmäßige und korrekte Verwendung von Referenzmaterialien (RM) und zertifizierten Referenzmaterialien (ZRM) und die damit gewährleistete Rückführung der Messergebnisse auf anerkannte Bezugsgrößen (Standards) setzt sich, nicht zuletzt durch die Anforderungen der ISO/IEC 17025, zunehmend durch. Die Zuverlässigkeit und Richtigkeit von Messergebnissen hängt wesentlich von der Verfügbarkeit von Referenzmaterialien ab. Zertifiziertes Referenzmaterial (ZRM) ist damit für die Analytik ein unentbehrliches Hilfsmittel geworden. PY - 2011 SN - 978-3-514-00788-8 SP - 98 EP - 112 PB - Stahlbau-Verl. CY - Düsseldorf AN - OPUS4-25148 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maack, Stefan A1 - Spies, M. A1 - Rieder, H. A1 - Orth, Th. T1 - Simulation of Ultrasonic Arrays for Industrial and Civil Engineering Applications Including Validation T2 - 38th Annual Review of Progress in Quantitative Nondestructive Evaluation (QNDE) 2011 CY - Burlington, VT, USA DA - 2011-07-17 PY - 2011 AN - OPUS4-29345 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mair, Georg A1 - Schoppa, André A1 - Pöschko, Pascal T1 - Verfahrensalternative zur wiederkehrenden Prüfung von Composite-Druckgefäßen N2 - Die aktuelle Praxis, auch die wiederkehrende Prüfung von Druckgefäßen aus Verbundwerkstoffen primär auf die hydraulische Innendruckprüfung abzustellen, ist kritisch zu bewerten. Zum einen tragen diese Prüfungen mit ihren relativ hohen Drücken vor dem Hintergrund der Schädigungsprozesse in Faser-Verbundwerkstoffen deutlich zur Degradation bei, zum anderen ist der Erkenntnisgewinn aus dieser Prüfung verschwindend. Um eine Abschätzung der sicheren Lebensdauern zu erhalten, bieten sich betriebsbegleitend zerstörende Prüfungen an. Kann man zwei zeitlich versetzte Zustandsbeschreibungen dieser Art miteinander vergleichen, sollten für jedes Baumuster/jede Bauart zeitabhängige Restfestigkeitsmerkmale ableitbar sein. Hierzu wird ein Ansatz formuliert, der spezifische Prüfverfahren und weitergehende Betrachtungen, z. B. über den geeigneten Zeitpunkt für Stichprobenprüfungen im Laufe der Betriebszeit, beinhaltet. KW - Degradation KW - Betriebssicherheit KW - Lastwechselversuche KW - Streuung KW - Restfestigkeiten KW - Ausfallwahrscheinlichkeit PY - 2011 SN - 2191-0073 VL - 1 IS - 7/8 SP - 38 EP - 43 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-24281 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mair, Georg A1 - Duffner, Eric A1 - Schoppa, André A1 - Szczepaniak, Mariusz T1 - Aspekte der Restfestigkeitsermittlung von Composite-Druckgefäßen mittels hydraulischer Prüfung N2 - Die aktuelle Praxis, auch die wiederkehrende Prüfung von Druckgefäßen aus Verbundwerkstoffen primär auf die hydraulische Innendruckprüfung abzustellen, ist kritisch bezüglich der Schädigung der Prüfmuster und ihrer Aussagekraft zu bewerten. Entsprechend wird nach einem Ansatz gesucht, auch durch betriebsbegleitend zerstörende Prüfungen eine aussagekräftige Zustandsbeschreibung der Population eines Baumusters zu erhalten. Im Beitrag werden erste Ergebnisse aus Prüfungen zur Ermittlung der Restlebensdauer von Composite-Druckgefäßen dargestellt und zunächst qualitativ diskutiert. Es wird erkennbar, dass die hydraulische LW-Prüfung durchaus geeignet ist, die Restlebensdauer von Baumustern mit metallischem Liner zu bewerten. Hierbei darf die Lastwechselzahl aus der hydraulischen Prüfung aber nicht als Füllzyklenzahl interpretiert werden. Außerdem können anhand der Ergebnisse die Möglichkeiten zur Restlebensdauerermittlung an lastwechselunempfindlichen Baumustern ohne metallische Liner deutlich eingegrenzt werden, was eine Konkretisierung möglicher Verfahren erlaubt; wenn dies auch an dieser Stelle noch keine Lösung bietet. KW - Restfestigkeiten KW - Degradation KW - Betriebssicherheit KW - Lastwechselprüfung KW - Streuspanne KW - Langsame Berstprüfung PY - 2011 SN - 2191-0073 VL - 1 IS - 9 SP - 50 EP - 55 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-24282 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Golze, Manfred A1 - Czichos, Horst A1 - Schmidt, Anita ED - Czichos, Horst ED - Saito, T. ED - Smith, L. T1 - Uncertainty and accuracy of measurement and testing N2 - In metrology and testing, the result of a measurement should always be expressed as the measured quantity value together with its uncertainty. The uncertainty of measurement is defined as a nonnegative Parameter characterizing the dispersion of the quantity values being attributed to a measurand. PY - 2011 SN - 978-3-642-16640-2 SP - 68 EP - 77 PB - Springer CY - Berlin, Heidelberg AN - OPUS4-24379 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulz, Michael A1 - Mair, Georg T1 - Forschungsaktivitäten an Leichtbaubehältern aus faserverstärkten Kunststoffen für den Gefahrgutbereich T2 - Transport Logistic 2011 CY - Munich, Germany DA - 2011-05-10 PY - 2011 AN - OPUS4-23798 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg T1 - Anerkannte Technische Regelwerke (ATR) in Deutschland T2 - 7. Fachgespräch ortsbeweglicher Druckgeräte CY - Berlin, Germany DA - 2011-10-18 PY - 2011 AN - OPUS4-24747 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg A1 - Spode, Manfred T1 - TPED 2010 und Ihre Anwendung T2 - 7. Fachgespräch ortsbeweglicher Druckgeräte CY - Berlin, Germany DA - 2011-10-18 PY - 2011 AN - OPUS4-24748 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulz, Michael A1 - Mair, Georg T1 - FUNDAMENTAL EXAMINATION OF A NEW CONCEPT OF SAFETY SURVEILLANCE AND INTERACTIVE DETERMINATION OF SAFE SERVICE LIFE FOR COMPOSITE PRESSURE VESSELS BY DESTRUCTIVE TESTS PARALLEL TO OPERATION T2 - !&TH iNTERNATIONAL cONFERENCE ON cOMPOSITE sTRCTURES 8iccs!&9 CY - Oporto, Portugal DA - 2011-06-28 PY - 2011 AN - OPUS4-23997 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pöschko, Pascal A1 - Mair, Georg T1 - Regulations and Research on RC&S for Hydrogen Storage Relevant to Transport and Vehicle Issues with Special Focus on Composite Containments T2 - International Conference on Hydrogen Safety ICHS 2011 CY - San Francisco, CA, USA DA - 2011-09-12 PY - 2011 AN - OPUS4-24407 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pöschko, Pascal A1 - Mair, Georg T1 - Ermittlung von Versagensgrenzen und Langzeitverhalten von Druckgefäßen aus Verbundwerkstoffen T2 - 7. Fachgespräch ortsbewegliche Druckgeräte, BAM CY - Berlin, Germany DA - 2011-10-18 PY - 2011 AN - OPUS4-24679 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Graf, P. A1 - Mantion, Alexandre A1 - Haase, A. A1 - Thünemann, Andreas A1 - Masic, A. A1 - Meier, W. A1 - Luch, A. A1 - Taubert, A. T1 - Silicification of peptide-coated silver nanoparticles - a biomimetic soft chemistry approach toward chiral hybrid core-shell materials N2 - Silica and silver nanoparticles are relevant materials for new applications in optics, medicine, and analytical chemistry. We have previously reported the synthesis of pH responsive, peptide-templated, chiral silver nanoparticles. The current report shows that peptide-stabilized nanoparticles can easily be coated with a silica shell by exploiting the ability of the peptide coating to hydrolyze silica precursors such as TEOS or TMOS. The resulting silica layer protects the nanoparticles from chemical etching, allows their inclusion in other materials, and renders them biocompatible. Using electron and atomic force microscopy, we show that the silica shell thickness and the particle aggregation can be controlled simply by the reaction time. Small-angle X ray scattering confirms the Ag/peptide@silica core–shell structure. UV–vis and circular dichroism spectroscopy prove the conservation of the silver nanoparticle chirality upon silicification. Biological tests show that the biocompatibility in simple bacterial systems is significantly improved once a silica layer is deposited on the silver particles. KW - Peptide-templated materials KW - Silver nanoparticles KW - Chiral nanoparticles KW - Ag/peptide@SiO2 nanostructures KW - Core-shell structures PY - 2011 DO - https://doi.org/10.1021/nn102969p SN - 1936-0851 VL - 5 IS - 2 SP - 820 EP - 833 PB - ACS Publ. CY - Washington, DC, USA AN - OPUS4-23207 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eisenacher, Germar A1 - Scheidemann, Robert A1 - Neumann, Martin A1 - Sterthaus, Jens A1 - Kasparek, Eva Maria A1 - Völzke, Holger T1 - Stauchversuche mit querdehnungsbehinderten Fichtenholzproben verschiedener Faserorientierungen bei veränderlicher Dehnrate T1 - Compression tests with laterally constrained spruce specimens with varying fiber orientations and loading rates N2 - Im Zuge des Forschungsvorhabens ENREA (Entwicklung rechnerischer Analysemethoden für stoßdämpfende Strukturen beim Anprall oder Absturz von Abfallgebinden) führt die BAM systematische Untersuchungen an stoßdämpfenden Werkstoffen, unter anderem an Fichtenholz, durch. Zweck der mit diesen Untersuchungen erzeugten Datenbasis ist die Erstellung und Parametrierung eines Finite-Elemente- (FE-) Materialmodells, das die Modellierung holzgefüllter stoßdämpfender Bauteile von Transportbehältern für radioaktive Stoffe in der FE-Simulation ermöglichen soll. Anhand von Ergebnissen aus der ersten Versuchsphase werden der Einfluss der Dehnrate und der Faserorientierung auf das Kraft-Verformungs-Verhalten von Fichtenholz diskutiert. Anschließend wird die rechnerische Modellierung von Fichtenholz diskutiert und die Anforderungen an ein Materialmodell werden erläutert. N2 - In the course of research project ENREA (development of numerical methods for analyzing impact limiters subjected to impact or drop scenarios), BAM is systematically investigating impact limiting materials, e. g. spruce wood. Goal of these investigations is to establish and parameterize a finite element (FE) material model which enables the modeling of wood filled impact limiting devices of transport casks for radioactive materials. Using results of the first test stage, the effect of loading rate and fiber orientation on the force-deflection characteristics of spruce wood will be presented. Following, computational modeling of spruce wood including requirements for a material model will be discussed. T2 - KONTEC 2011 - 10. Internationales Symposium "Konditionierung radioaktiver Betriebs- und Stilllegungsabfälle" CY - Dresden, Germany DA - 06.04.2011 PY - 2011 N1 - Sprachen: Deutsch/Englisch - Languages: German/English SP - 465 EP - 478 AN - OPUS4-23684 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jaunich, Matthias A1 - von der Ehe, Kerstin A1 - Wolff, Dietmar A1 - Völzke, Holger A1 - Stark, Wolfgang T1 - Understanding low temperature properties of elastomer seals N2 - Elastomers are widely used as the main sealing materials for containers for low and intermediate level radioactive waste and as an additional component to metal seals in spent fuel and high active waste containers. The safe encapsulation of the radioactive container inventory has to be guaranteed according to regulation and appropriate guidelines for long term storage periods as well as for temperatures as low as -40°C during transport. Therefore, the understanding of failure mechanisms that lead to leakage at low temperatures is of high importance. It is known that the material properties of elastomers are strongly temperature dependent. At low temperatures, this is caused by the rubber-glass transition (abbreviated: glass transition). During continuous cooling, the material changes from a rubber-like entropy elastic to a stiff energy elastic behaviour, which allows nearly no strain or retraction. Hence, rubbers are normally used above their glass transition, but the minimum working temperature limit is not defined precisely; this can cause problems during the above noted applications. Therefore, the lower operation temperature limit of elastomer seals must be determined in dependence of the material properties. Differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) are combined with standardised measurements to determine the compression set according to ISO 815. To reduce the test time of the standard tests, a faster technique than normally used was developed. Additionally, the breakdown temperature of the sealing function of complete O ring seals was measured in a component test set-up to compare it with the results of the other tests. The experimental set-up is capable of measuring the leakage rate at low temperatures by the pressure rise method. A fluorocarbon rubber (FKM) was selected for this investigation as it is often used for radioactive waste containers. The materials (seals and test sheets) were purchased from a commercial seal producer. KW - Sealing material KW - Elastomer KW - Compression set KW - Dynamic mechanical analysis KW - Low temperature behaviour PY - 2011 DO - https://doi.org/10.1179/1746510911Y.0000000004 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 22 IS - 2 SP - 83 EP - 88 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-24015 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kasparek, Eva Maria A1 - Scheidemann, Robert A1 - Wolff, Dietmar A1 - Zencker, Uwe A1 - Völzke, Holger T1 - Untersuchungen zum Verhalten von Dämpferbeton unter Stossbelastung N2 - Während des Transportes sind Behälter für hoch radioaktive Abfälle durch stoßdämpfende Bauteile vor Einwirkungen, die aus Unfallszenarien gemäß den IAEA Regularien resultieren können, weitestgehend geschützt. Nach dem Entfernen dieser Komponenten im Rahmen der Einlagerung ins Zwischenlager müssen Vorkehrungen getroffen sein, um Beanspruchungen der Behälter aus möglichen Handhabungsunfällen im Empfangsbereich zu reduzieren. Die Maßnahmen müssen vor allem darauf abzielen, die stoßdämpfenden Eigenschaften der potentiellen Aufprallflächen zu optimieren. Da Standardmaterialien für Fundamente nur ein geringes Energieabsorptionsvermögen aufweisen, wurde durch die Firma HOCHTIEF eine neuartige Betonmixtur entwickelt, bei der ein spezieller Leichtzuschlag zum Einsatz kommen. Zur Charakterisierung dieses sogenannten Dämpferbetons liegen Standardkennwerte vor sowie Messwerte aus Eindringversuchen, die zur Qualitätssicherung für jede Produktcharge durchgeführt werden. Das stoßdämpfende Potential des neuen Werkstoffs kann jedoch nur dann vollkommen ausgeschöpft werden, wenn die Energieabsorption in numerischen Simulationen der Behälterabstürze über die gesamte Belastungsdauer zuverlässig wiedergegeben wird. Für die Implementierung und Anpassung eines entsprechenden Materialmodelis in einem Finite Elemente (FE) Programm sind Daten aus systematischen Druckversuchen mit Variation der relevanten Einflussgrößen erforderlich. An der BAM werden daher im Rahmen eines werkstoffübergreifenden Forschungsvorhabens zur Untersuchung von stoßdämpfenden Strukturen auch die Eigenschaften von Dämpferbeton experimentell untersucht und zugehörige numerische Methoden entwickelt. Der aktuelle Beitrag behandelt die Ergebnisse der ersten Projektphase, in der kubische Probekörper mit der Kantenlänge 100mm bei unterschiedlichen Lagerungsbedingungen statisch und dynamisch gestaucht wurden. In nachfolgenden Versuchen wird der Einfluß der Probengröße ermittelt sowie die Eignung der verwendeten Materialmodelle anhand realistischer Belastungssituationen validiert. Versuchsprogramm. T2 - Jahrestagung Kerntechnik 2011 CY - Berlin, Germany DA - 17.05.2011 KW - Stoßdämpfende Werkstoffe KW - Materialmodellierung KW - Versuchsprogramm KW - Stoßbelastung KW - Dehnratenabhängigkeit KW - Temperaturabhängigkeit KW - Polyurethan Schaum KW - Dämpferbeton PY - 2011 IS - Session TS-17 / Paper 171 SP - 1 EP - 5 AN - OPUS4-23836 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kasparek, Eva Maria A1 - Zencker, Uwe A1 - Scheidemann, Robert A1 - Völzke, Holger A1 - Müller, Karsten T1 - Numerical and experimental studies of polyurethane foam under impact loading N2 - Proper predictions of the behaviour of shock absorber materials are of utmost importance in safety assessments for licensing casks for transport and storage of highly active waste. After having identified significant discrepancies between numerical results and the actual response of polyurethane foam limiters subjected to accidental scenarios, a new research project ENREA was established by BAM. A major objective is to enhance and to develop advanced material models intended to simulate limiters under impact loading. They should account for all major factors influencing the load–deformation relationship like temperature, strain rate and specific stress state. The corresponding test program, applicable plasticity models, the overall parameter identification strategy based on local and global optimization techniques as well as experimental and numerical results are presented here in particular for closed cell foams. KW - Polyurethane foam KW - Limiter KW - Impact loading KW - Strain rate KW - Plasticity model KW - Parameter identification PY - 2011 DO - https://doi.org/10.1016/j.commatsci.2010.11.025 SN - 0927-0256 VL - 50 IS - 4 SP - 1353 EP - 1358 PB - Elsevier CY - Amsterdam AN - OPUS4-23151 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pöschko, Pascal A1 - Mair, Georg T1 - Anwendung numerischer Verfahren auf Restfestigkeitswerte von Stichproben - Vorhersage sicherer Verwendungsdauern von Composite-Druckgefäßen N2 - Die aktuelle Praxis, auch die wiederkehrende Prüfung von Druckgefäßen aus Verbundwerkstoffen primär auf die hydraulische Innendruckprüfung abzustellen, ist sowohl hinsichtlich der Schädigung der Prüfmuster als auch ihrer Aussagekraft kritisch zu bewerten. Entsprechend wird nach einem Ansatz gesucht, auch durch betriebsbegleitende zerstörende Prüfungen eine aussagekräftige Zustandsbeschreibung der Population eines Baumusters zu erhalten. Für die Bewertung der Ergebnisse aus diesen Prüfungen wird eine Methode zur statistischen Auswertung vorgestellt, die es erlaubt, die Extrapolation von Zuverlässigkeitslinien auch auf relativ kleine Stichproben aufzubauen und so das Ende der sicheren Gebrauchsdauer auf der Basis von Grenzwerten für Mindestlast und maximal zulässiger Ausfallwahrscheinlichkeit auf systematische wie auch konservative Weise zu determinieren. KW - Restfestigkeiten KW - Degradation KW - Betriebssicherheit KW - Lastwechselversuche KW - Stochastische Modellierung KW - Lebensdauerverteilungen PY - 2011 SN - 2191-0073 VL - 1 IS - 10 SP - 46 EP - 52 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-24472 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kannengießer, Thomas A1 - Rethmeier, Michael A1 - Portella, Pedro Dolabella A1 - Ewert, Uwe A1 - Redmer, Bernhard T1 - Assessment of hot cracking behaviour in welds N2 - Hot crack assessment during production and processing of metallic materials is an essential prerequisite for the safety of welded structures. The hot cracking investigations presented here were carried out as part of a study aimed at the development of Cr/Ni low transformation temperature filler materials. Low transformation temperature alloys open up the possibility for welding high strength steels. The externally loaded Modified Varestraint Transvarestraint hot cracking test was employed in the experiments described. The hot cracking resistance was evaluated with the help of light microscopy applied at the specimen surface. The proportionality between hot cracking susceptibility and Cr/Ni alloy content was explained by the altered solidification kinetics and by the enlarged solidification interval. The internal crack paths and the three-dimensional structure of the crack net in the material volume were examined using X-ray computer tomography. The total crack lengths for different material depths and circumjacent rectangular volumes, respectively, were be determined. An increasing hot cracking susceptibility with increasing Cr/Ni alloy content was also be established for the specimen volume. KW - Hot cracking KW - Low transformation temperature (LTT) alloy KW - Modified varestraint transvarestraint (MVT) hot cracking test KW - X-ray computer tomography PY - 2011 DO - https://doi.org/10.3139/146.110545 SN - 1862-5282 VL - 102 IS - 8 SP - 1001 EP - 1006 PB - Carl Hanser CY - München AN - OPUS4-24400 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Wolff, Dietmar T1 - Safety aspects of long dry interim cask storage of spent fuel in Germany N2 - Dry cask storage of spent fuel and high active waste front reprocessing is licensed and established in Germany for up to 40years so far. About 10years ago, the strategy has been shifted from centralized storage using facilities in Ahaus and Gorleben to cit-site storage facilities in Order to avoid immediate cask shipping from nuclear power plants. At present, several hundred casks are stored safeiy and without any major problem. BAM is highly involved in cask specific safety evaluations within the scope of licensing procedures as well as of quality assurance procedures during cask fabrication, loading and storage. A major prerequisite for any cask storage license is a valid transport Type B license. Subsequently, cask transportability has to be ensured at any point during the entire storage period. So far, this requirement is met by continuous maintenance of the Type B license. Anyhow, IAEA Type B regulations do not consider permanently loaded storage casks that have the sole purpose of being finally shipped öfter decades of storage inducing ageing effects. No transport safety demonstration has to be performed on aged cask components. T2 - International high-level radioactive waste management conference (IHLRWMC 2011) CY - Albuquerque, NM, USA DA - 10.04.2011 KW - Safety KW - Cask KW - Interim storage KW - Spent fuel PY - 2011 SP - 712 EP - 719 AN - OPUS4-23651 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Probst, Ulrich A1 - Wolff, Dietmar A1 - Nagelschmidt, Sven A1 - Schulz, Sebastian T1 - Investigations on the long term behavior of metal seals for spent fuel storage casks N2 - Metal seals are in common use as an essential component for the leak tight closure of transport and storage casks for spent fuel and vitrified high active waste from reprocessing. They are placed between the massive monolithic cask body made of ductile cast iron or forged steel and the primary and secondary lids, which are fixed with screws around the lid circumference, in order to ensure long term safe enclosure of the radioactive cask inventory. Hereby, long term reliable pressure forces in combination with a tight surface contact are as important as well maintained seal and surface qualities and dry and clean conditions during seal assembly and operation. A few years ago BAM started systematic investigation on the long term seal behavior with re-spect to longer storage periods and seal behavior in accidental cask scenarios with dynamic de-formations of the seal groove geometry or short term drop in pressure force up to lid lifting. BAM has developed test flanges for seals with full scale cross section diameter but much small-er outer diameter to gain representative data for metal-sealed lid systems. They are placed in appropriate testing machines for relevant mechanical loading under static and dynamic condi-tions with the ability to measure the standard helium leakage rate continuously during each test phase. This paper focuses on BAM long term tests of different seal types with aluminum and silver jackets at three different temperatures of +20°C, +100°C and +150°C under static conditions over longer periods of time. Due to creeping effects, a reduction of the pressure force does ap-pear during loading and unloading depending on prior holding times. So far, test results of up to 2 years indicate a clear correlation between seal pressure forces and holding time, temperature and seal type allowing for extrapolating to much longer periods of time. The paper presents basic correlations, test and evaluation procedures as well as important provisional results and gives an outlook on further investigations. T2 - 52nd INMM Annual meeting CY - Palm Desert, CA, USA DA - 17.07.2011 PY - 2011 SP - 1 EP - 9 AN - OPUS4-24173 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank A1 - Wolff, Dietmar A1 - Droste, Bernhard A1 - Völzke, Holger T1 - Requirements for transport packages after interim storage N2 - In Germany the concept of dry interim storage of spent fuel and vitrified high active waste in dual purpose metal casks is implemented (currently for periods of up to 40 years). The casks being used have an approved package design in accordance with the international transport regulations. The license for dry storage is granted on the German Atomic Energy Act with respect to the guidelines of the German Reactor Safety Commission for dry interim storage of spent fuel. Currently part of the assessment process of the cask design for transport on public routes is to evaluate the suitability of the used materials with respect to their properties and their compatibility for possible transport periods. For transport on public routes during or after long term interim storage periods, it has to be ensured that the transport and storage casks fulfill the specifications of the transport approval or other sufficient properties which satisfy the proofs for the compliance of the safety objectives at that time. This paper describes the state-of-the-art technology in Germany and points out arising prospective challenges and which related questions have to be answered in future. Present research and knowledge concerning the long term behavior of transport and storage cask components (such as gaskets and shielding components) have to be consulted as well as experiences from interim cask storage operations. Challenges in the safety assessment are therefore i.e. the behavior of aged metal and elastomeric gaskets under IAEA test conditions to ensure that the results of drop tests can be transferred to the compliance of the safety objectives at the time of transport after the interim storage period (aged package). Assessment methods for the material compatibility, the behavior of fuel assemblies and the aging behavior of shielding parts (e. g. influence of radiation) are further issues as well. T2 - 52nd INMM Annual meeting CY - Palm Desert, CA, USA DA - 17.07.2011 KW - Transport package design KW - Interim storage KW - Inspections KW - Log term behavior KW - Dual purpose casks PY - 2011 SP - 1 EP - 9 AN - OPUS4-24172 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kasparek, Eva Maria A1 - Scheidemann, Robert A1 - Zencker, Uwe A1 - Völzke, Holger T1 - Numerical and experimental investigations of temperature effect on dynamically loaded polyurethane foams T2 - COMPLAS XI - XI International Conference on Computational Plasticity CY - Barcelona, Spain DA - 2011-09-07 PY - 2011 AN - OPUS4-24422 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Portella, Pedro Dolabella A1 - Falkenberg, Rainer A1 - Krause, Martin A1 - Osterloh, Kurt A1 - Rücker, Werner A1 - Gumenyuk, Andrey T1 - Werkstoffaspekte bei der Auslegung von Windenergietürmen T2 - VDI-Fachkonferenz "Turm und Fundament von Windenergieanlagen" CY - Hamburg, Germany DA - 2011-10-12 PY - 2011 AN - OPUS4-24667 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumeyer, Tino A1 - Müller, Karsten A1 - Völzke, Holger T1 - Experimental Drop Testing of Waste Containers for the KONRAD Repository T2 - ICEM 2011 - 14th International Conference on Environmental Remediation and radioactive Waste Management CY - Reims, France DA - 2011-09-25 PY - 2011 AN - OPUS4-24449 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank A1 - Wolff, Dietmar A1 - Droste, Bernhard A1 - Völzke, Holger T1 - Requirements on Transport Packages after Interim Storage - Curent Spproach and Perspectives T2 - NMM 52nd Annual Meeting CY - Palm Desert, CA, USA DA - 2011-07-17 PY - 2011 AN - OPUS4-24127 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger T1 - IAEA Consultancy Meeting: Spent Fuele Storage Demonstration Project Review - Presentation from Germany - T2 - IAEA Consultancy Meeting on Spent fuele Storage Demonstration Project CY - Vienna, Austria DA - 2011-08-09 PY - 2011 AN - OPUS4-24133 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nies, Daniel A1 - Rehmer, Birgit A1 - Skrotzki, Birgit T1 - Testing Thermal Barrier Coatings by Laser Excitation T2 - Euromat 2011 CY - Montpellier, France DA - 2011-09-12 PY - 2011 AN - OPUS4-24526 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kasparek, Eva Maria A1 - Scheidemann, Robert A1 - Zencker, Uwe A1 - Wolff, Dietmar A1 - Völzke, Holger T1 - Experimentelle und numerische Untersuchungen von stoßdämpfenden Werkstoffen für Behälter zur Entsorgung radioaktive / Experimental and numerical studies of impact limiting materials for containers for radioactive waste T2 - 10. Internationales Symposium "Konditionierung radioaktiver Betriebs- und Stilllegungsabfälle" KONTEC CY - Dresden, Germany DA - 2011-04-06 PY - 2011 AN - OPUS4-23557 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Nieslony, Gregor A1 - Noack, Volker A1 - Hagenow, Peter A1 - Kovacs, Oliver T1 - Aktuelle Entwicklungen auf dem Gebiet der Behälter-Bauartprüfungen für das Endlager Konrad T2 - KONTEC 2011 CY - Dresden, Germany DA - 2011-04-06 PY - 2011 AN - OPUS4-23484 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Portella, Pedro Dolabella T1 - Materialversagen, Risiko und unscharfe Grenzen T2 - Tagung "Unscharfe Grenzen im Umwelt- und Technikrecht" CY - Aachen, Germany DA - 2011-03-25 PY - 2011 AN - OPUS4-23440 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger T1 - ESCP Experimental Working Group Meeting T2 - ESCP Experimental Working Group Meeting CY - Baltimore, MD, USA DA - 2011-05-02 PY - 2011 AN - OPUS4-23689 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fedelich, Bernard A1 - Epishin, A. A1 - Link, T. A1 - Klingelhöffer, Hellmuth A1 - Künecke, Georgia A1 - Portella, Pedro Dolabella T1 - Experimental characterization and mechanical modelling of creep induced rafting in superalloys T2 - 21st International Workshop on Computational Mechanics of Materials CY - Limerick, Ireland DA - 2011-09-22 PY - 2011 AN - OPUS4-23867 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wolff, Dietmar A1 - Völzke, Holger T1 - Safety Aspects of Long-Term Dry Interim Storage of Spent Fuel in Germany T2 - Technical Meeting on Very Long Term Storage of Used Nuclear Fuel; IAEA CY - Vienna, Austria DA - 2011-04-26 PY - 2011 AN - OPUS4-23839 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank A1 - Wolff, Dietmar A1 - Droste, Bernhard A1 - Völzke, Holger T1 - Requirements on Transport Packages after Interim Storage - Current Approach and Perspectives T2 - U.S. NRC Workshop CY - Washington, D.C., USA DA - 2011-07-11 PY - 2011 AN - OPUS4-24126 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Völzke, Holger A1 - Wolff, Dietmar T1 - Ageing Management - very long term storage of used nuclear fuel T2 - Technical Meeting on "Very long term storage of used nuclear fuel" CY - Vienna, Austria DA - 2011-04-26 PY - 2011 AN - OPUS4-23791 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Noack, Volker A1 - Nieslony, Gregor A1 - Völzke, Holger A1 - Hörning, Tony A1 - Kovacs, Oliver A1 - Hagenow, Peter T1 - Aktueller Stand bei den Behälter-Bauartprüfungen für das Endlager Konrad N2 - In Deutschland werden zwei Arten von radioaktiven Abfällen unterschieden: Wärme entwickelnde Abfälle und Abfälle mit vernachlässigbarer Wärmeentwicklung. Im Endlager Konrad werden ausschließlich radioaktive Abfälle mit vernachlässigbarer Wärmeentwicklung endgelagert (im internationalen Sprachgebrauch: schwach- und mittelradioaktive Abfälle). Solche Abfälle stammen zum Beispiel aus dem laufenden Betrieb, der Stilllegung und dem Rückbau von Kernkraftwerken, aus der Forschung, der Medizin oder von der Bundeswehr und beinhalten unter anderem kontaminierte Baustoffe, Schrott, Werkzeuge, Schutzkleidung, Schlämme und Suspensionen. Vor dem Endlagern dieser Abfälle werden sie konditioniert, d. h. die festen Abfälle werden teilweise zerkleinert, verpresst oder zementiert, flüssige eingedampft oder zementiert und häufig anschließend in Fässer verpackt. Im nächsten Schritt werden die konditionierten Abfälle in Abfallbehälter verpackt. Geeignete Behältertypen sind (gemäß IM, 121) kubische Container oder Rundbehälter mit definierten Abmaßen aus Stahlblech, Beton oder Gusseisen. Diese Abfallbehälter sind für die Endlagerung, für eine vorausgehende längerfristige Zwischenlagerung sowie ggf. für den Transport über öffentliche Verkehrswege zu qualifizieren. T2 - Jahrestagung Kerntechnik 2011 CY - Berlin, Germany DA - 17.05.2011 KW - Kerntechnik KW - Endlagerung KW - Gutachten KW - Behälter KW - Bauartprüfung PY - 2011 IS - Session TS-19 / Paper 91 SP - 1 EP - 5 AN - OPUS4-25550 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erhard, Anton A1 - Noack, Volker A1 - Völzke, Holger T1 - Storage facilities at Sayda Bay N2 - Within the framework of the G8 partnership, the German Ministry of Economics and Technology has been realizing a 300 EUR million project of the storage of decommissioned Russian nuclear submarines based on a German-Russian agreement. The main parts of the project are the construction of the long-term storage facility as well as a radioactive waste storage facility at Sayda Bay. Long-term interim storage facility for this particular case has a period of about 70 years. The Energiewerke Nord GmbH (EWN) under the technical controlling of BAM carried out the project management. Foremost in this presentation is the finalization of the long-term storage facility for nuclear submarine compartments and the planning and realization of the radioactive waste storage building with special emphases of the parts carried out by BAM. Because BAM staff cannot stay permanently on site, a random inspection of different topics was the bases for the activities of BAM. The key aspects of activities are the long-term storage of the nuclear compartments, maintenance building, the decommissioning of the compartments and the transportation of the very heavy weight compartments (1600 metric tons). Details relating of the progress of the construction work as well as information about technical recommendations will also be briefly illustrated. Within this scope, problems and difficulties during the construction of the storage facility as well as logistical challenges including transportation of the reactor compartments will also be discussed. T2 - 52nd INMM Annual meeting CY - Palm Desert, CA, USA DA - 17.07.2011 KW - Storage facility KW - Nuclear reactor compartments PY - 2011 SP - 1 EP - 7 AN - OPUS4-26197 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Noack, Volker A1 - Nieslony, Gregor A1 - Völzke, Holger A1 - Hörning, Tony A1 - Kovacs, Oliver A1 - Hagenow, Peter T1 - Aktueller Stand bei den Behälter-Bauartprüfungen für das Endlager KONRAD T2 - Jahrestagung Kerntechnik 2011, Berliner Congress Center (BBC) CY - Berlin, Germany DA - 2011-05-17 PY - 2011 AN - OPUS4-25479 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Portella, Pedro Dolabella A1 - Trappe, Volker A1 - Gumenyuk, Andrey A1 - Gradt, Thomas T1 - Mit Sicherheit innovativ: Der Beitrag der Werkstofftechnik T2 - Ehrenkolloquium für Prof. Bernhard Wielage, Technische Universität Chemnitz CY - Chemnitz, Germany DA - 2011-09-01 PY - 2011 AN - OPUS4-24669 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Portella, Pedro Dolabella A1 - Rücker, Werner A1 - Trappe, Volker T1 - Aerogeradores offshore: problems e possíveis soluções T2 - Plenarvortrag, Dia dos Materiais 2011 CY - Lisbon, Portugal DA - 2011-11-02 PY - 2011 AN - OPUS4-24674 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Erhard, Anton A1 - Völzke, Holger A1 - Probst, Ulrich A1 - Wolff, Dietmar T1 - Aging management for long-term interim storage casks N2 - The aging management system for the mechanical components of nuclear power plants (NPPs) must be established and used by the licensee in such a way that the quality of safety relevant components is guaranteed for the completely designed lifetime of the NPP. This demands an extensive plant life management with special emphases on the knowledge of the degradation in material properties. The basic safety concept in Germany observes this circumstance. Lifetime extension of the German NPPs is an aim of the current valid coalition agreement of the German government. Operational extension of interim storage facilities requires, in comparison to the aging management system for NPP, an aging management system adapted to the Special circumstances of spent fuel storage casks. Extension of interim storage periods for spent fuel casks beyond the designed lifetime requires, in comparison to the components of an NPP, an increasing knowledge of material degradation with potential impact on cask integrity, e.g. leak tightness. Dry interim storage in Germany has been approved for 40 years. After that time, according to the present strategy, a final repository should be available. However, until now, such a final facility still does not exist, and the German exploration and licensing process is heavily delayed. Currently, discussions are continuing regarding further exploration of the Gorleben salt mine. There is willingness to overcome this situation that is clearly described in the available coalition agreement of the federal government. Anyway, however, the prediction is viewed; a repository for heat generating radioactive waste in Germany will not be available in the near future and may not be available when first storage facilities and casks reach their 40 years of approved lifetime, which will occur in ~25 years starting from now. Therefore, the question must be asked: what has to be done with the existing storage casks in the interim facilities? May these casks be fit for continued use, with an extension of the storage period? One option is to have an aging management system, which creates enough information about the technical condition of safety relevant cask properties. This is the basis for safety evaluation for extended storage periods. In the present paper, possible aging mechanisms for high level waste storage casks are discussed, as well as the influence of the time dependent changes of the component properties. KW - Long term interim storage KW - Storage casks KW - Aging mechanisms KW - Degradation mechanisms KW - Metal seals KW - Larson-Miller parameter PY - 2011 DO - https://doi.org/10.1179/1746510910Y.0000000013 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 22 IS - 1 SP - 46 EP - 53 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-23890 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kasparek, Eva Maria A1 - Völzke, Holger A1 - Scheidemann, Robert A1 - Zencker, Uwe A1 - Wolff, Dietmar T1 - Experimentelle und numerische Untersuchungen von stoßdämpfenden Werkstoffen für Behälter zur Entsorgung radioaktiver Stoffe N2 - Die mechanische Beanspruchung von Transport- und Lagerbehältern für radioaktive Stoffe gemäß den durch die IAEA vorgegebenen Prüfszenarien oder bei Unfällen, die während der Handhabung in einer kerntechnischen Anlage auftreten können, wird maßgeblich durch das Design der Stoßdämpfer und die Eigenschaften des jeweiligen Untergrundes beeinflusst. Da der Nachweis der Behälterintegrität und -dichtheit häufig an numerische Simulationen gekoppelt ist, sind für die sicherheitstechnische Auslegung der Konstruktion zuverlässige Informationen über das Energieabsorptionsvermögen der Werkstoffe und eine geeignete Umsetzung dieser Daten in FEM - Programme erforderlich. Die im Rahmen von Falluntersuchungen bei der BAM festgestellten, teilweise erheblichen Abweichungen zwischen experimentellen und berechneten Größen sind entsprechend darauf zurückzuführen, dass die zur Verfügung stehenden numerischen Verfahren das komplexe Verhalten der stoßdämpfenden Strukturen nicht ausreichend präzise wiedergeben. Hiervon besonders betroffen sind Bauteile aus Holz und Polyurethan-Schaum (PU-Schaum), die zur Konstruktion von Behälterstoßdämpfern für die Transportkonfiguration eingesetzt werden, sowie Dämpferbeton, der in ausgewählten Bereichen im Fundament von Standort-Zwischenlagern eingebaut wird. Um die zugehörigen Materialmodelle weiter zu entwickeln und die dafür erforderliche Datenbasis zu schaffen, hat die BAM vor knapp zwei Jahren das vom BMBF geförderte Forschungsvorhaben ENREA (Entwicklung rechnerischer Analysemethoden für stoßdämpfende Strukturen beim Anprall oder Absturz von Abfallgebinden) gestartet. Wesentlicher Bestandteil ist ein systematisches Versuchsprogramm, bei dem die drei genannten Werkstoffe statisch und dynamisch hohen Druckbelastungen ausgesetzt werden. Relevante Versuchsparameter sind, neben der Dehnrate, die Temperatur und Lagerungsbedingungen sowie die Orientierung des Werkstoffes hinsichtlich der Belastungsrichtung. Dieser Beitrag präsentiert die wichtigsten Ergebnisse aus der ersten Versuchsphase, die durch weggesteuerte Versuche mit konstanten Prüfgeschwindigkeiten von 0,02 mm/s und 3000 mm/s gekennzeichnet ist. Darüber hinaus wird die Verwertung dieser Daten zur Anpassung von Materialmodellen auf der Grundlage von Nachrechnungen gezeigt, wobei die Möglichkeiten und Grenzen der verwendeten Konzepte Umrissen werden. Aufgrund des Umfangs, den die Versuche mit Holzwerkstoffen einnehmen, und des erforderlichen Aufwandes für die numerische Modellierung werden die entsprechenden Maßnahmen und Ergebnisse in einem eigenständigen Beitrag auf der KONTEC vorgestellt. T2 - KONTEC 2011 - 10. Internationales Symposium "Konditionierung radioaktiver Betriebs- und Stilllegungsabfälle" CY - Dresden, Germany DA - 06.04.2011 KW - Stoßdämpfende Werkstoffe KW - Materialmodellierung KW - Versuchsprogramm KW - Stoßbelastung KW - Dehnratenabhängigkeit KW - Temperaturabhängigkeit KW - Polyurethan Schaum KW - Dämpferbeton PY - 2011 SP - 453 EP - 458 AN - OPUS4-23709 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pulz, Robert A1 - Rehmer, Birgit A1 - Skrotzki, Birgit T1 - Pyrometric temperature measurement of ceramic thermal shock samples N2 - The determination of critical failure parameters during thermal shock requires a time and space resolved temperature measurement of the sample. High frequency pyrometry is a suitable technique for such a measurement task, which usually requires the knowledge of the optical properties of the investigated material. Another challenge is the infrared transparency of materials to be checked in the wavelength range of the pyrometer. The thermal shock disks are very thin, due to the need of homogeneous temperature distribution and to maintain a two-dimensional problem. To allow a pyrometric temperature measurement a universal calibration method for high frequency infrared cameras has been developed. Pyrometry in various media was demanded, as well as the estimation of optical properties (reflection, transmittance and emission) for the selected ceramics to be tested. KW - Temperature measurement KW - Ceramics KW - Emission coefficient KW - Radiation thermometry KW - Thermal shock PY - 2011 DO - https://doi.org/10.1016/j.measurement.2010.09.050 SN - 0263-2241 SN - 1873-412X VL - 44 IS - 1 SP - 259 EP - 266 PB - Elsevier Ltd. CY - London AN - OPUS4-22474 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vogl, Jochen A1 - Rosner, Martin A1 - Pritzkow, Wolfgang T1 - Development and validation of a single collector SF-ICPMS procedure for the determination of boron isotope ratios in water and food samples N2 - Boron isotope studies on technical materials and geological and environmental samples are one hot topic in nowadays isotope research. Provenance studies of artefacts, food and other products might become another one, as several recent studies demonstrate. Typically boron isotope determinations have been carried out by TIMS. To open up this research field to a broader scientific community we developed two analytical procedures for boron isotope determinations based on single collector SF-ICPMS combined with a sample preparation procedure consisting of dry-ashing and a three step ion chromatographic boron-matrix separation. The developed procedures consist of one low resolution (LR) and one medium resolution (MR) procedure. The repeatability for the δ11B determination in three independently measured aliquots lies between 0.2 and 0.8‰ for the LR procedure and between 0.3 and 1.5‰ for the MR procedure. The expanded uncertainties with a coverage factor of k=2 range between 1.4 and 1.6‰ for the LR procedure and between 2.9 and 3.2‰ for the MR procedure. The accuracy, expressed as average deviation from the reference values, is 0.43‰ for the LR procedure and 0.33‰ for the MR procedure. To test the practicability of the procedures the matrix tolerance has been investigated as well and was found to be up to 2 mg kg-1 of alkaline and alkaline earth elements in the final measurement solution containing 100 µg kg-1 boron. Thus a highly efficient matrix separation for SF-ICPMS boron isotope determinations is required, similar to TIMS. PY - 2011 DO - https://doi.org/10.1039/c0ja00220h SN - 0267-9477 SN - 1364-5544 VL - 26 IS - 4 SP - 861 EP - 869 PB - Royal Society of Chemistry CY - London AN - OPUS4-23419 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pulz, Robert A1 - Rehmer, Birgit T1 - Laser thermal shock experiments - performance and evaluation on the basis of advanced ceramics N2 - The thermal shock behaviour in air and vacuum of three different advanced ceramics is investigated by introducing a new testing method. This thermal shock testing system permits the reproducible setting of defined temperature profiles in thin disks. In order to perform heating - up thermal shock experiments under reproducible conditions and to measure the transient temperature fields, a laser beam is directed spirally across the surface of the specimen. In this process, the specimen is heated up faster than the temperature gradient is compensated by thermal conductivity. Resulting temperature fields were recorded space and time resolved. Based on the knowledge of the local temperature distribution at the moment of failure, the critical fracture stress can be calculated. The scatter of thermal shock strength is quantitatively determined for the tested ceramics by using a improved statistical method. KW - Thermal shock KW - Weibull statistics KW - Environmental media PY - 2011 DO - https://doi.org/10.1088/1757-899X/18/20/202019 SN - 1757-899X N1 - Serientitel: IOP Conference Series: Materials Science and Engineering – Series title: IOP Conference Series: Materials Science and Engineering IS - Symposium 14 SP - 202019, 1 EP - 4 AN - OPUS4-33028 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dey, Anika A1 - Casperson, Ralf A1 - Pohl, Rainer A1 - Thomas, Hans-Martin A1 - Heyder, R. T1 - Erfahrungen mit der Wirbelstromprüfung beim Einsatz an unterschiedlichen Schienenstahlsorten N2 - Die steigenden Anforderungen im Schienenverkehr haben u. a. wachsende Betriebsbeanspruchungen für das Führungselement Schiene zur Folge. Auf Strecken mit hohen Belastungen wird dadurch die Entstehung von Rollkontaktermüdungsrissen, den sog. Head Checks, begünstigt. Für die Quantifizierung von Schäden im Hinblick auf eine optimierte Instandhaltung, setzt die DB AG daher seit einigen Jahren die Wirbelstromprüfung an Schienen ein. Es wurde ein Wirbelstromprüfsystem speziell für die Detektion und Bewertung von Head Checks auf der Schienenstahlsorte R260 entwickelt. Um den Instandhaltungsaufwand möglichst gering zu halten, unterliegen Eisenbahnschienen einer ständigen technologischen Weiterentwicklung durch die Hersteller. Durch Verbesserung der Schienenstahlsorten soll ein größerer Widerstand gegen die Bildung von Rollkontaktermüdungsrissen erreicht werden. Anhand von Streckenversuchen der DB AG in den letzten Jahren konnte festgestellt werden, dass tatsächlich eine Verminderung der Risswachstumsgeschwindigkeit erzielt wurde. Dafür zeigten sich im Vergleich zur Stahlsorte R260 abweichende Rissgeometrien, geringere Abstände zwischen den Ermüdungsrissen und somit eine größere Dichte des Rissfeldes. Die daraus resultierenden Folgen für die Ergebnisse der Wirbelstromprüfung werden hier erläutert. Praktische Prüferfahrungen an Schienenstahlsorten mit höherer Festigkeit werden vorgestellt. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Wirbelstromprüfung KW - Rollkontaktermüdung KW - Schienenstahlsorten KW - Schienenfehler KW - Eisenbahnschiene PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-252793 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Di.2.A.4) SP - 1 EP - 10 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25279 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Casperson, Ralf A1 - Dey, Anika A1 - Pohl, Rainer A1 - Thomas, Hans-Martin T1 - 'Verortung' der Prüfergebnisse bei der ZfP an Eisenbahnschienen N2 - Das Schienennetz der DB und anderer Bahngesellschaften wird regelmäßig mit Schienenprüfzügen inspiziert. Die mit den Prüfzügen aufgenommenen Messdaten werden offline zu einem späteren Zeitpunkt ausgewertet. Um Prüfbefunde manuell nachprüfen und ggf. Reparaturmaßnahmen einleiten zu können, ist eine möglichst exakte Zuordnung der Befunde zum Prüfort notwendig. Theoretisch ist jeder Ort des Schienennetzes durch Streckennummer, Richtungskennzahl und Kilometrierung exakt beschrieben. In der Praxis treten jedoch bei der Zuordnung diverse Probleme auf: Die Kilometrierung wird während der Prüfung manuell erfasst, indem die Beschriftung der Kilometer- bzw. Hektometertafeln in das Prüfsystem eingegeben und deren Position beim Vorbeifahren per Tastendruck in die Messdaten 'eingeblitzt' wird. Die Hektometertafeln stehen jedoch nicht an der aufgedruckten Position, sondern sind am nächstgelegenen Mast montiert. Dagegen ist die Ungenauigkeit des manuellen 'Einblitzens' vernachlässigbar. Außerdem ist die Kilometrierung nicht immer eindeutig, da nach Umbaumaßnahmen Kilometersprünge (sowohl fehlende als auch doppelte Kilometer) auftreten können. Abhilfe verspricht der Einsatz des satellitengestützten GPS, vorausgesetzt, die Strecken sind exakt vermessen. Um eine ausreichende Positionsgenauigkeit auch bei schlechten Empfangsbedingungen zu erreichen, ist jedoch ein erheblicher Aufwand notwendig. Die Positionsgenauigkeit eines Standard-GPS-Empfängers genügt hier nicht. Es wird ein Verortungssystem hoher Positionsgenauigkeit auf der Basis des GPS vorgestellt, das sich derzeit in der Erprobung befindet. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Zerstörungsfreie Prüfung KW - Verortung KW - GPS PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-252802 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (P85) SP - 1 EP - 5 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-25280 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Purohit, Purv A1 - Huacuja Sánchez, Jesús A1 - Wang, D.-Y. A1 - Emmerling, Franziska A1 - Thünemann, Andreas A1 - Heinrich, G. A1 - Schönhals, Andreas T1 - Structure - property relationships of nanocomposites based on polypropylene and layered double hydroxides N2 - Nanocomposites based on polypropylene (PP) and organically modified ZnAl layered double hydroxides (ZnAl-LDH) were prepared by melt blending and investigated by a combination of differential scanning calorimetry (DSC), small- and wide-angle X-ray scattering (SAXS and WAXS), and dielectric relaxation spectroscopy (DRS). An average number of stack size of LDH layers is calculated by analyzing the SAXS data which is close to that of pure organically modified ZnAl-LDH. Scanning microfocus SAXS investigations show that the ZnAl-LDH is homogeneously distributed in the PP matrix as stacks of 4–5 layers with an intercalated morphology. DSC and WAXS results show that the degree of crystallinity decreases linearly with the increasing content of LDH. The extrapolation of this dependence to zero estimates a limiting concentration of ca. 40% LDH where the crystallization of PP is completely suppressed by the nanofiller. The dielectric spectra of the nanocomposites show several relaxation processes which are discussed in detail. The intensity of the dynamic glass transition (β-relaxation) increases with the concentration of LDH. This is attributed to the increasing concentration of the exchanged anion dodecylbenzenesulfonate (SDBS) which is adsorbed at the LDH layers. Therefore, a detailed analysis of the β-relaxation provides information about the structure and the molecular dynamics in the interfacial region between the LDH layers and the polypropylene matrix which is otherwise dielectrically invisible (low dipole moment). As a main result, it is found that the glass transition temperature in this interfacial region is by 30 K lower than that of pure polypropylene. This is accompanied by a drastic change of the fragility parameter deduced from the relaxation map. KW - Nanocomposites KW - Layered double hydroxide KW - Dielectric spectroscopy KW - X-ray scattering KW - Polypropylene PY - 2011 DO - https://doi.org/10.1021/ma200323k SN - 0024-9297 SN - 1520-5835 VL - 44 IS - 11 SP - 4342 EP - 4354 PB - American Chemical Society CY - Washington, DC AN - OPUS4-23921 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Haase, A. A1 - Arlinghaus, H. F. A1 - Tentschert, J. A1 - Jungnickel, H. A1 - Graf, P. A1 - Mantion, Alexandre A1 - Draude, F. A1 - Galla, S. A1 - Plendl, J. A1 - Goetz, M.E. A1 - Masic, A. A1 - Meier, W. A1 - Thünemann, Andreas A1 - Taubert, A. A1 - Luch, A. T1 - Application of laser postionization secondary neutral mass spectrometry / time-of-flight secondary ion mass spectrometry in nanotoxicology: Visualization of nanosilver in human macrophages and cellular responses N2 - Silver nanoparticles (SNP) are the subject of worldwide commercialization because of their antimicrobial effects. Yet only little data on their mode of action exist. Further, only few techniques allow for visualization and quantification of unlabeled nanoparticles inside cells. To study SNP of different sizes and coatings within human macrophages, we introduce a novel laser postionization secondary neutral mass spectrometry (Laser-SNMS) approach and prove this method superior to the widely applied confocal Raman and transmission electron microscopy. With time-of-flight secondary ion mass spectrometry (TOF-SIMS) we further demonstrate characteristic fingerprints in the lipid pattern of the cellular membrane indicative of oxidative stress and membrane fluidity changes. Increases of protein carbonyl and heme oxygenase-1 levels in treated cells confirm the presence of oxidative stress biochemically. Intriguingly, affected phagocytosis reveals as highly sensitive end point of SNP-mediated adversity in macrophages. The cellular responses monitored are hierarchically linked, but follow individual kinetics and are partially reversible. KW - Nanosilver KW - Laser-SNMS KW - TOF-SIMS KW - Confocal Raman microscopy KW - Oxidative stress KW - Protein carbonyls PY - 2011 DO - https://doi.org/10.1021/nn200163w SN - 1936-0851 VL - 5 IS - 4 SP - 3059 EP - 3068 PB - ACS Publ. CY - Washington, DC, USA AN - OPUS4-23656 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Knappe, Patrick A1 - Boehmert, L. A1 - Bienert, Ralf A1 - Karmutzki, S. A1 - Niemann, B. A1 - Lampen, A. A1 - Thünemann, Andreas T1 - Processing nanoparticles with A4F-SAXS for toxicological studies: Iron oxide in cell-based assays N2 - Nanoparticles are not typically ready-to-use for in vitro cell culture assays. Prior to their use in assays, powder samples containing nanoparticles must be dispersed, de-agglomerated, fractionated by size, and characterized with respect to size and size distribution. For this purpose we report exemplarily on polyphosphate-stabilized iron oxide nanoparticles in aqueous suspension. Fractionation and online particle size analysis was performed in a time-saving procedure lasting 50 min by combining asymmetrical flow field-flow fractionation (A4F) and small-angle X-ray scattering (SAXS). Narrowly distributed nanoparticle fractions with radii of gyration (Rg) from 7 to 21 nm were obtained from polydisperse samples. The A4F-SAXS combination is introduced for the preparation of well-characterized sample fractions originating from a highly polydisperse system as typically found in engineered nanoparticles. A4F-SAXS processed particles are ready-to-use for toxicological studies. The results of preliminary tests of the effects of fractionated iron oxide nanoparticles with a Rg of 15 nm on a human colon model cell line are reported. KW - Field-flow-fractionation KW - Small-angle X-ray scattering KW - Nanoparticle PY - 2011 DO - https://doi.org/10.1016/j.chroma.2010.11.012 SN - 0021-9673 VL - 1218 IS - 27 SP - 4160 EP - 4166 PB - Elsevier CY - Amsterdam AN - OPUS4-23951 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Haase, A. A1 - Tentschert, J. A1 - Graf, P. A1 - Mantion, Alexandre A1 - Jungnickel, H. A1 - Draude, F. A1 - Plendl, J. A1 - Galla, S. A1 - Thünemann, Andreas A1 - Taubert, A. A1 - Arlinghaus, H. F. A1 - Luch, A. T1 - Cellular effects of nanosilver in human macrophages: Uptake, oxidative stress response, lipid alterations and functional impairment T2 - NanoImpactNet Conference "Building a bridge from NanoImpactNet to nanomedical research" CY - Lausanne, Switzerland DA - 2011-02-14 PY - 2011 AN - OPUS4-23749 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Haase, A. A1 - Tentschert, J. A1 - Graf, P. A1 - Mantion, Alexandre A1 - Draude, F. A1 - Jungnickel, H. A1 - Plendl, J. A1 - Arlinghaus, H. F. A1 - Taubert, A. A1 - Thünemann, Andreas A1 - Luch, A. T1 - Cellular effects of nanosilver in human macrophages: Uptake, oxidative stress, lipid alterations and functional impairment T2 - 5th International Conference on Nanotechnology - Occupational and Environmental Health CY - Boston, MA, USA DA - 2011-08-09 PY - 2011 AN - OPUS4-23748 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Haase, A. A1 - Tentschert, J. A1 - Graf, P. A1 - Mantion, Alexandre A1 - Draude, F. A1 - Jungnickel, H. A1 - Plendl, J. A1 - Arlinghaus, H. F. A1 - Luch, A. A1 - Taubert, A. A1 - Thünemann, Andreas T1 - Cellular effects of nanosilver in human macrophages: Uptake, oxidative stress, lipid alterations and functional impairment T2 - 5. Innovationskongress Chemie und Biotechnologie/ Kleine Partikel - große Chancen CY - Potsdam, Germany DA - 2011-05-19 PY - 2011 AN - OPUS4-23746 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mantion, Alexandre A1 - Graf, P. A1 - Haase, A. A1 - Meier, W. A1 - Luch, A. A1 - Plendl, J. A1 - Thünemann, Andreas A1 - Masic, A. A1 - Taubert, A. T1 - New chiral peptide-coated silver nanoparticles for Material Science and Toxicology T2 - 25th ECIS Conference and the 45. Hauptversammlung der Kolloidgesellschaft CY - Berlin, Germany DA - 2011-09-04 PY - 2011 AN - OPUS4-23977 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thünemann, Andreas A1 - Knappe, Patrick A1 - Weidner, Steffen T1 - An X-ray view into the nano-world T2 - Workshop "Trends in Colloid and Interface Science TICI" CY - Potsdam, Germany DA - 2011-06-22 PY - 2011 AN - OPUS4-23978 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Knappe, Patrick A1 - Boehmert, L. A1 - Karmutzki, S. A1 - Niemann, B. A1 - Lampen, A. A1 - Bienert, Ralf A1 - Weidner, Steffen A1 - Thünemann, Andreas T1 - Fraktionierung und Charakterisierung von Eisenoxid-Nanopartikeln mittels A4F-SAXS Online-Kopplung und Untersuchung der Zytotoxizität an Caco-2 Zellen T2 - 48. Wiss. Kongress der Deutschen Gesellschaft für Ernährung (DGE), Uni Potsdam CY - Potsdam, Germany DA - 2011-03-16 PY - 2011 AN - OPUS4-23597 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Thünemann, Andreas A1 - Klobes, Peter A1 - Wieland, Christoph A1 - Bruzzano, S. T1 - On the nanostructure of micrometer-sized cellulose beads N2 - The analysis of the porosity of materials is an important and challenging field in analytical chemistry. The gas adsorption and mercury intrusion methods are the most established techniques for quantification of specific surface areas, but unfortunately, dry materials are mandatory for their applicability. All porous materials that contain water and other solvents in their functional state must be dried before analysis. In this process, care has to be taken since the removal of solvent bears the risk of an incalculable alteration of the pore structure, especially for soft materials. In the present paper, we report on the use of small-angle X-ray scattering (SAXS) as an alternative analysis method for the investigation of the micro and mesopores within cellulose beads in their native, i.e., water-swollen state; in this context, they represent a typical soft material. We show that even gentle removal of the bound water reduces the specific surface area dramatically from 161 to 109 m² g-1 in cellulose bead sample type MT50 and from 417 to 220 m² g-1 in MT100. Simulation of the SAXS curves with a bimodal pore size distribution model reveals that the smallest pores with radii up to 10 nm are greatly affected by drying, whereas pores with sizes in the range of 10 to 70 nm are barely affected. The SAXS results were compared with Brunauer–Emmett–Teller results from nitrogen sorption measurements and with mercury intrusion experiments. KW - Small-angle X-ray scattering KW - Cellulose KW - Mesopores KW - Micropores KW - Porosimetry PY - 2011 DO - https://doi.org/10.1007/s00216-011-5176-z SN - 1618-2642 SN - 1618-2650 VL - 401 IS - 4 SP - 1101 EP - 1108 PB - Springer CY - Berlin AN - OPUS4-24251 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Haase, A. A1 - Tentschert, J. A1 - Jungnickel, H. A1 - Graf, P. A1 - Mantion, Alexandre A1 - Draude, F. A1 - Plendl, J. A1 - Goetz, M.E. A1 - Galla, S. A1 - Masic, A. A1 - Thünemann, Andreas A1 - Taubert, A. A1 - Arlinghaus, H. F. A1 - Luch, A. T1 - Toxicity of silver nanoparticles in human macrophages: uptake, intracellular distribution and cellular responses N2 - Silver nanoparticles (SNP) are among the most commercialized nanoparticles worldwide. They can be found in many diverse products, mostly because of their antibacterial properties. Despite its widespread use only little data on possible adverse health effects exist. It is difficult to compare biological data from different studies due to the great variety in sizes, coatings or shapes of the particles. Here, we applied a novel synthesis approach to obtain SNP, which are covalently stabilized by a small peptide. This enables a tight control of both size and shape. We applied these SNP in two different sizes of 20 or 40 nm (Ag20Pep and Ag40Pep) and analyzed responses of THP-1-derived human macrophages. Similar gold nanoparticles with the same coating (Au20Pep) were used for comparison and found to be non-toxic. We assessed the cytotoxicity of particles and confirmed their cellular uptake via transmission electron microscopy and confocal Raman microscopy. Importantly a majority of the SNP could be detected as individual particles spread throughout the cells. Furthermore we studied several types of oxidative stress related responses such as induction of heme oxygenase I or formation of protein carbonyls. In summary, our data demonstrate that even low doses of SNP exerted adverse effects in human macrophages. KW - Silver nanoparticles KW - Neurotoxicology KW - Protein carbonyls KW - ROS PY - 2011 DO - https://doi.org/10.1088/1742-6596/304/1/012030 SN - 1742-6588 SN - 1742-6596 VL - 304 SP - 012030-1 - 012030-14 PB - IOP Publ. CY - Bristol, UK AN - OPUS4-24035 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mantion, Alexandre A1 - Graf, P. A1 - Haase, A. A1 - Plendl, J. A1 - Thünemann, Andreas A1 - Meier, W. A1 - Taubert, A. A1 - Luch, A. A1 - Vila-Comamala, J. A1 - Diaz, A. A1 - Grolimund, D. A1 - Sachtleben, M. T1 - Silver nanoparticles and synchrotron light-based nanotoxicology: new imaging modalities T2 - JUM@P´11: Second Joint Users´ Meeting@PSI, Paul Scherrer-Institut CY - Villigen, Switzerland DA - 2011-09-15 PY - 2011 AN - OPUS4-23979 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Haase, A. A1 - Tentschert, J. A1 - Graf, P. A1 - Draude, F. A1 - Jungnickel, H. A1 - Plendl, J. A1 - Arlinghaus, H. F. A1 - Thünemann, Andreas A1 - Taubert, Annette A1 - Luch, A. A1 - Mantion, Alexandre T1 - Cellular effects of nanosilver in human macrophages: Uptake, oxidative stress, lipid alterations and functional impairment T2 - Annual Meeting and Toxexpo, Society of Toxicology CY - Washington, D.C., USA DA - 2011-03-06 PY - 2011 AN - OPUS4-24258 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mantion, Alexandre A1 - Haase, A. A1 - Graf, P. A1 - Plendl, J. A1 - Thünemann, Andreas A1 - Meier, W. A1 - Taubert, A. A1 - Luch, A. T1 - A novel type of silver nanoparticles and their advantages in toxicity testing in cell culture systems T2 - 5. Innovationskongress Chemie und Biotechnologie /Kleine Partikel - große Chancen CY - Potsdam, Germany DA - 2011-05-19 PY - 2011 AN - OPUS4-24060 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mantion, Alexandre A1 - Haase, Andreas A1 - Graf, P. A1 - Plendl, J. A1 - Thünemann, Andreas A1 - Meier, W. A1 - Luch, A. A1 - Taubert, A. T1 - A novel type of silver nanoparticles and their advantages in toxicity testing in cell systems T2 - 5th International Conference on Nanotechnology- Occupational and Environmental Health CY - Boston, MA, USA DA - 2011-08-09 PY - 2011 AN - OPUS4-24226 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Girod, Matthias A1 - Weidner, Steffen A1 - Thünemann, Andreas T1 - Analysis of Aggregation of Silver nanoparticles by Small-angle X-ray Scattering T2 - 16. Tagung für Festkörperanalytik CY - Vienna, Austria DA - 2011-07-04 PY - 2011 AN - OPUS4-24224 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Polte, Jörg A1 - Rademann, Klaus A1 - Thünemann, Andreas A1 - Kraehnert, R. A1 - Emmerling, Franziska T1 - Fundamental Principles of Metal Nanoparticle Growth T2 - 25th ECIS Conference CY - Berlin, Germany DA - 2011-06-14 PY - 2011 AN - OPUS4-24257 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tentschert, J. A1 - Jungnickel, H. A1 - Haase, A. A1 - Arlinghaus, H. F. A1 - Graf, P. A1 - Mantion, Alexandre A1 - Draude, F. A1 - Galla, S. A1 - Plendl, J. A1 - Goetz, M. E. A1 - Masic, A. A1 - Meier, W. A1 - Thünemann, Andreas A1 - Taubert, A. A1 - Luch, A. T1 - Analysis of Cell Membrane Changes in Functional Impaired Human Macrophages after Nanosilver Treatment T2 - SIMS XVIII CY - Riva del Garda, Italy DA - 2011-10-18 PY - 2011 AN - OPUS4-24260 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mantion, Alexandre A1 - Haase, A. A1 - Plendl, J. A1 - Thünemann, Andreas A1 - Taubert, A. A1 - Meier, W. T1 - A novel type of silver nanoparticles and their advantages in toxicity testing in cell culture systems T2 - INRS Occupational Health Research Conference 2011: Risks associated to Nanoparticles and Nanomaterials CY - Nancy, France DA - 2011-04-05 PY - 2011 AN - OPUS4-24259 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar A1 - Emmerling, Franziska A1 - Müller, Urs A1 - Panne, Ulrich T1 - Hochaufgelöste in situ Sy-XRD Untersuchungen an zementgebundenen Baustoffen T2 - GDCh-Wissenschaftsforum Chemie 2011 CY - Bremen, Germany DA - 2011-09-04 PY - 2011 AN - OPUS4-24215 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zeng, Y. A1 - Grandner, S. A1 - Oliveira, C.L.P. A1 - Thünemann, Andreas A1 - Paris, O. A1 - Pedersen, J.S. A1 - Klapp, S.H.L. A1 - von Klitzing, R. T1 - Effect of particle size and Debye length on order parameters of colloidal silica suspensions under confinement N2 - Using atomic force microscopy (AFM) and small angle X-ray scattering (SAXS), we show a full comparison between structuring of nanoparticles in confinement and in bulk in order to explain the effect of confinement on characteristic lengths and the scaling law of the characteristic lengths. Three different-sized particle suspensions are used to check the generalization and the correlation between the characteristic lengths and the system parameters, like particle diameter and Debye length. The two characteristic lengths obtained from AFM force curves, the oscillatory wavelength λ, which is related to the average particle distance, and the decay length ξ, which measures how far particle correlates to obtain periodic oscillations, are in good agreement with the mean particle distance 2π/qmax and the correlation length 2/Δq in bulk, respectively, obtained from the structure peaks of SAXS diagrams. Although confinement causes layering of nanoparticles parallel to the confining surfaces, the characteristic lengths in the direction perpendicular to the confining surfaces follow the bulk behavior. The wavelength scales as ρ-1/3 with the particle number density ρ irrespective of the particle size and the ionic strength and shows a pure volume effect. Upon comparing with literature results, the λ = ρ-1/3 scaling law can be applied more generally for charged particles, as long as the repulsive interaction is sufficiently long-ranged, than the previous expression of λ = 2(R + κ-1), which only approaches the value of average particle distance under specific conditions. The decay length ξ is controlled both by the particle size and the ionic strength of the suspensions, and ξ = R + κ-1 is proposed in the paper. In addition, the interaction strength, the force amplitude and maximum scattering intensity, increases linearly with particle concentration. On the other hand, the Monte Carlo (MC) simulations and approximate hypernetted chain (HNC) closure calculation based on Derjaguin-Landau-Verwey-Overbeek (DLVO) potential are employed to study the characteristic lengths from the theoretical point of view. The experimental wavelengths are in good agreement with the theoretical counterparts and the experimental decay lengths show the same qualitative behavior as theoretical ones on the particle size and ionic strength. KW - Nanoparticle PY - 2011 DO - https://doi.org/10.1039/c1sm05971h SN - 1744-683X VL - 7 IS - 22 SP - 10899 EP - 10909 PB - RSC Publ. CY - Cambridge AN - OPUS4-24660 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mantion, Alexandre A1 - Graf, P. A1 - Florea, I. A1 - Haase, A. A1 - Thünemann, Andreas A1 - Masic, A. A1 - Ersen, O. A1 - Rabu, P. A1 - Meier, W. A1 - Luch, A. A1 - Taubert, A. T1 - Biomimetic synthesis of chiral erbium-doped silver/peptide/silica core-shell nanoparticles (ESPN) N2 - Peptide-modified silver nanoparticles have been coated with an erbium-doped silica layer using a method inspired by silica biomineralization. Electron microscopy and small-angle X-ray scattering confirm the presence of an Ag/peptide core and silica shell. The erbium is present as small Er2O3 particles in and on the silica shell. Raman, IR, UV-Vis, and circular dichroism spectroscopies show that the peptide is still present after shell formation and the nanoparticles conserve a chiral plasmon resonance. Magnetic measurements find a paramagnetic behavior. In vitro tests using a macrophage cell line model show that the resulting multicomponent nanoparticles have a low toxicity for macrophages, even on partial dissolution of the silica shell. KW - Nanoparticle KW - Small-angle X-ray scattering KW - SAXS PY - 2011 DO - https://doi.org/10.1039/c1nr10930h SN - 2040-3364 SN - 2040-3372 VL - 3 IS - 12 SP - 5168 EP - 5179 PB - RSC Publ. CY - Cambridge AN - OPUS4-25422 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubowski, Norbert A1 - Lindner, Uwe A1 - Panne, Ulrich A1 - Chinthalapati, Siva Kesava Raju T1 - Speciation of gadolinium based MRI contrast agents in environmental water samples using hydrophilic interaction chromatography coupled to inductively coupled plasma mass spectrometry T2 - Third International Symposium on Metallomics CY - Münster, Germany DA - 2011-06-15 PY - 2011 AN - OPUS4-24106 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Hauer, B. A1 - Pierkes, R. A1 - Schäfer, S. A1 - Seidel, M. A1 - Herbst, Tristan A1 - Rübner, Katrin A1 - Meng, Birgit T1 - Verbundforschungsvorhaben 'Nachhaltig Bauen mit Beton' - Potenziale des Sekundärstoffeinsatzes im Betonbau - Teilprojekt B N2 - Die Nutzung und Weiterverarbeitung von Sekundärstoffen kann in der Baustoffherstellung einen Beitrag zum nachhaltigen Bauen leisten. Im Rahmen des Teilprojekts B wurde die Bewertung dieser Potenziale anhand von Beispielen ausgebaut und verifiziert. Die Basis dieser Bewertungsgrundlage ist die Erfüllung der grundlegenden technischen Anforderungen (ökobilanzielle Indikatoren, vergleichende ökobilanzielle Betrachtung). Im Teilprojekt E geht es um die Freisetzung umweltrelevanter Stoffe aus zementgebundenen Baustoffen. Überprüft werden sollte die Übereinstimmung zwischen Laborergebnissen, Modellierungen und realen Grundwasserkonzentrationen. Es wurden Schlitzwände errichtet, die in den Grundwasserleiter einbinden und umweltrelevante Parameter bestimmt. Grundsätzlich hat sich selbst bei Großbaustellen nur eine geringe Beeinflussung der Grundwasserqualität durch Beton ergeben. KW - Sekundärstoff KW - Zement KW - Beton KW - Nachhaltigkeit KW - Bewertung KW - Recycling KW - Betonbrechsand KW - Müllverbrennungsasche KW - Kesselsand KW - Ökobilanz PY - 2011 SN - 978-3-410-65094-2 SN - 0171-7197 IS - 584 SP - 1 EP - 151 PB - Beuth CY - Berlin AN - OPUS4-25982 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Müller, B. A1 - Panasková, J. A1 - Danielak, M. A1 - Horn, Wolfgang A1 - Jann, Oliver A1 - Müller, D. T1 - Sensorische Bewertung der Emissionen aus Bauprodukten - Integration in die Vergabegrundlagen für den Blauen Engel und das Bewertungsschema des Ausschusses zur gesundheitlichen Bewertung von Bauprodukten (UBA-FB 001500 / Förder-Kennz. 370762300) N2 - Emissionen aus Bauprodukten beeinträchtigen die Qualität der Innenraumluft erheblich. Mit Hilfe des AgBB-Schemas werden die Emissionen flüchtiger organischer Verbindungen (VOC) aus Bauprodukten bewertet. Die gesundheitliche Bewertung nach dem AgBB-Schema erfordert produktspezifische Messverfahren. Diese gibt es mittlerweile für eine Reihe von Produkten. Sie wurden durch Beteiligung verschiedener Forschungseinrichtungen und Messinstitute validiert und u. a. in die Vergabekriterien des Umweltzeichens Blauer Engel übernommen. Die Bewertung ist allerdings –mit zumeist niedrigeren Grenzwerten –strenger. VOC-Emissionen und Gerüche können beide zu gesundheitlichen Belastungen führen. So ist die sensorische Prüfung ein weiteres wichtiges Element bei der Bewertung von Bauprodukten und vorsorglich auch im AgBB-Schema verankert. Hauptziel des Projektes ist es, eine Methode der sensorischen Bewertung und Grenzen für die Vergabe des Blauen Engels und für das AgBB-Schema abzuleiten. Auf Grundlage der durchgeführten Untersuchungen (siehe Kapitel 5 Ergebnisse und Diskussion) wird als Bewertungsmethode die empfundene Intensität und die Hedonik vorgeschlagen. Die Ableitung der Grenzwerte für die sensorische Bewertung am 28. Tag erfolgt über die zusätzliche Befragung der Probanden im Rahmen der vorliegenden Studie nach der Zumutbarkeit einer Probe. Für den Blauen Engel könnte es je Produktgruppe unterschiedliche Grenzen der empfundenen Intensität und der Hedonik geben. Ein erster Vorschlag für mögliche Grenzen, hier zunächst einheitlich für alle Produktgruppen, ist für die empfundene Intensität 7 pi (5 pi + 2 pi als Sicherheit, Kapitel 5.1.5) und für die Hedonik -1 (0 +/-0,8, gerundet auf -1) (siehe dazu Abbildung 6-2). KW - Bauprodukt KW - Schadstoff KW - Prüfverfahren KW - Blauer Engel KW - SVOC KW - Flüchtige Emission KW - Kohlenwasserstoff KW - Geruch KW - Sensorik KW - AgBB-Schema PY - 2011 UR - http://www.umweltbundesamt.de/publikationen/sensorische-bewertung-emissionen-aus-bauprodukten SN - 1862-4804 IS - 35 SP - 1-146, Anhang 1-109 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-24926 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Müller, B. A1 - Panasková, J. A1 - Danielak, M. A1 - Horn, Wolfgang A1 - Jann, Oliver A1 - Müller, D. T1 - Sensory-based evaluation of building product emissions - Integration into the Blue Angel award criteria and assessment scheme of the Committee for Health Evaluation of Building Products (UBA-FB 001500 / Förder-Kennz. 370762300) N2 - Emissions from building products can considerably impair the quality of indoor air. The AgBB scheme is employed to evaluate the emissions of volatile organic compounds (VOC) from building products. The hygienic evaluation according to the AgBB scheme requires product-specific measuring procedures. These are available for a range of products. They have been validated in co-operation with several research and testing institutes and have been included in the criteria for awarding the Blue Angel ecolabel. The evaluation is, however, stricter and generally has lower limits. VOC emissions and odours can cause health problems so testing using sensors is an important element in the evaluation of building products and has – for reasons of precaution – been set down in the AgBB scheme. The main goal of the project was to derive a method of evaluation using sensors and limits for awarding the Blue Angel and for the AgBB scheme. Based on the research conducted (see Chapter 5 Results and Discussion), perceived intensity and hedonics were suggested as a suitable Evaluation method. The derivation of limits for the evaluation using sensors on the 28th day was effected in the present study through the additional questioning of the test subjects on the reasonability of a sample. For the Blue Angel, there could be different limits of perceived intensity and hedonics for each group of products. A preliminary suggestion for possible limits – for all product groups – is a perceived intensity of 7 pi (5 pi + 2 pi as confidence coefficient, Chapter 5.1.5) and -1 (0+/-0.8, rounded to -1) for the hedonic value. KW - Labelsysteme KW - VOC KW - Geruch KW - Geruchstest KW - Emissionsmessungen KW - Building product KW - Directive KW - Health care KW - Pollutant KW - Test method KW - Hydrocarbon KW - Testing using sensors KW - Emission KW - Emission test chamber KW - Odour KW - AgBB scheme KW - Health assessment KW - Assessment procedure KW - Volatile organic compounds KW - Very volatile organic compounds KW - VVOC KW - Semi volatile organic compounds KW - SVOC KW - Thermal desorption KW - GC/MS KW - GC-ODP KW - Odour standard of comparison KW - Floor coverings KW - Coverings KW - Blue Angel KW - Odour evaluation KW - Acceptability KW - Perceived intensity KW - Hedonic KW - Reasonability KW - Standardization KW - Environmental sign KW - Volatile emission KW - Product labelling PY - 2011 UR - http://www.umweltbundesamt.de/publikationen/sensory-based-evaluation-of-building-product SN - 1862-4804 IS - 61 SP - 1-133, Annex 1-109 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-25200 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wiegner, Katharina A1 - Farke, M. A1 - Horn, Wolfgang A1 - Jann, Oliver A1 - Hahn, Oliver ED - Brozio, P. T1 - Schadstoffe im Museum richtig einschätzen N2 - Schadstoffe beschäftigen derzeit Museen weltweit Heute weiß man, dass diese auch aus Materialien, die für den Ausstellungsbau verwendet werden, austreten können, was eine Gefahr für Exponate darstellt. Ein neues Verfahren namens BEMMA bietet nun erstmalig die Möglichkeit, relativ schnell und effektiv eine problemorientierte Untersuchung und Bewertung mit belastbaren und reproduzierbaren Ergebnissen vorzunehmen. KW - Emissionsarme Vitrinen KW - Präventive Konservierung KW - VOC KW - BEMMA PY - 2011 SN - 978-3-7667-1962-1 SP - 127 EP - 131 PB - Callwey CY - München AN - OPUS4-25377 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiegner, Katharina A1 - Hahn, Oliver A1 - Farke, M. A1 - Kalus, Sabine A1 - Horn, Wolfgang T1 - Determination of formic and acetic acids in air N2 - Formic and acetic acids are often responsible for damage of cultural objects, e. g. glass and metal corrosion or changing and fading of colours. Museums all around the world are equipped with different show cases. Display cases should protect cultural objects from dust as well as from mechanical damage. Several construction materials which are used for display cases, including wood, glue and coatings, are possible sources of very volatile organic compounds (VVOCs), volatile organic compounds (VOCs) and semi volatile organic compounds (SVOCs). These construction products can emit formic and acetic acids into the indoor or display case air. Modern display cases with small air change rates can cause higher concentrations of formic and acetic acids if any source is installed in the display case (Salthammer and Uhde, 2009). To minimize the risk of damage emissions from building products must be quantified. There is a need for a method for identification and quantification of acetic and formic acid. Some possibilities for the identification of acetic acid exist. The quantification of acetic acid for example after sampling on TENAX® or CARBOTRAP and thermal desorption-GC in accordance with ISO 16000-6 and ISO 16017-1 results in very low recovery rates. A new method should be stabile, robust, reproducible and comparable, with an easy local sampling and determination in laboratories. Miniaturised emission test chambers and model display cases were used to study the recovery rates. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - VOCs KW - Detection of formic and acetic acid KW - Quantification of formic and acetic acid KW - Air sampling PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-23876 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang A1 - Müller, B. A1 - Panaskova, J. A1 - Jann, Oliver A1 - Plehn, W. A1 - Müller, D. T1 - VOC emissions from building materials accompanying sensory tests for different evaluation schemes N2 - Within a follow up project of a former study (Horn et al. 2005) emissions and odor from different types of construction products were investigated (financed by the German Federal Environmental Agency - FKZ 37 07 62 300). The tested materials were mainly those used for construction of floors indoors. For this type of materials in Germany several labeling procedures exist which are based on Emission chamber testing. Two important labeling procedures in Germany are based on the AgBBevaluation scheme (Däumling et al. 2005). For some applications (flooring material) it is the mandatory Ü-mark of DIBt (German Institute for Construction Technology). Furthermore for carpets, adhesives and many other products, like sealants, mattresses, furniture and so on the voluntary blue angel mark exist. Within this scheme the volatile organic compounds (VOC) compounds are measured with well established procedures and are evaluated with LCI-values which were derived from health information. Beyond that many complaints according to building products are caused by odors. Therefore an evaluation procedure for the odor is very important and should be implemented into all of the mentioned labeling schemes. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - Odor KW - Construction product KW - VOC-emission KW - Evaluation KW - AgBB PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-23881 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang A1 - Wiegner, Katharina A1 - Wilke, Olaf A1 - Jann, Oliver T1 - Method validation study for VOC emission measurements N2 - Quality and trueness of results received from measurements are very important for all involved parties, producers and consumers as well; for instance, if the results were used for acceptance of a product within a labeling procedure. Based on an inter-laboratory study with many German, European and US-American laboratories an extemal quality assurance System for the analysis of VOC emitting from products or the measurement in indoor air should be implemented (financed by the German Federal Environmental Agency). A focus was set on the emission test chamber experiments and the connected analytical procedure. VOC have a dominating influence when applying the German AgBB scheme for health evaluation of building products. Therefore it is necessary to ensure that the results between the testing laboratories are comparable. The successful participation to such round robin tests is offen essential for the acceptance of results given by an analytical laboratory. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - Round robin test KW - VOC KW - Construction product KW - Emission PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-23880 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Horn, Wolfgang A1 - Wiegner, Katharina T1 - Inter-laboratory study to check the performance ot test chamber measurements for product emission testing N2 - The labelling of construction products or building materials as “low-emitting” is based on measurements using third-party emission test chambers. Unfortunately there is no method to validate the performance of such test chamber measurements. This might give a Variation of results when testing one material at different laboratories. Therefore it is necessary to hold round robin tests as part of the quality management System to ensure comparable results. A research project financed by the Federal Environmental Agency focused on the development of an external quality management System for the detection of relevant Chemical compounds from products and in ambient air. The project was structured in four phases (Horn et al., 2009 and 2011; Wilke et al., 2009a) This paper shows results of the fourth phase of the project, which was an inter-laboratory study for VOC-emission testing by means of emission test chambers. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - Emission test chamber KW - Product emission testing KW - VOC-Emission KW - Round robin test PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-23884 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Wiegner, Katharina A1 - Scheffer, Harald A1 - Brödner, Doris T1 - VOC-Emissions from Plywood boards N2 - Wood and wood products are often used as construction material for buildings and even more for furniture and indoor decoration. Therefore Chemical emissions from wood have an influence on the indoor air quality. A research project financed by the Federal Environmental Agency focused on VOC emissions from oriented Strand boards (OSB) and also from plywood made from pine and spruce (Wilke et al., 2011a). This paper shows results of the plywood testing because only little information is available about plywood emission behaviour and its impact on indoor air quality. T2 - Indoor Air 2011, 12th International conference on indoor air quality and climate CY - Austin, TX, USA DA - 05.06.2011 KW - VOC-Emission KW - Plywood KW - Terpenes KW - Aldehydes KW - Indoor air quality PY - 2011 IS - Paper 768 SP - 1 EP - 2 AN - OPUS4-23885 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Damberg, Klaudia A1 - Wiegner, Katharina A1 - Horn, Wolfgang A1 - Kroh, L.W. T1 - Development and optimization of Methods for measurement of insecticides and higher siloxanes in Display cases T2 - Technart 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-23916 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mull, Birte A1 - Wiegner, Katharina A1 - Horn, Wolfgang T1 - Development of a Screening Method for Semi Volatile Organic Compounds in Museum Showcases T2 - TECHNART 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-23914 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reinhardt, F. A1 - Beckhoff, B. A1 - Pollakowski, B. A1 - Bresch, Harald A1 - Seeger, Stefan A1 - Wahlschläger, U. T1 - Analyzing the chemical composition of ultrafine particles by X-Ray specctrometry under grazing incidence T2 - International Symposium "Ultrafine Particles" CY - Brussels, Belgium DA - 2011-05-26 PY - 2011 AN - OPUS4-23870 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiegner, Katharina A1 - Horn, Wolfgang A1 - Wilke, Olaf A1 - Kalus, Sabine A1 - Jann, Oliver T1 - Development of a reference material for volatile organic compound emissions in test chambers T2 - EURACHEM: 7th Workshop; Proficiency testing in analytical chemistry, microbiology and laboratory medicine; Current Practice and Future Directions CY - Istanbul, Turkey DA - 2011-10-02 PY - 2011 AN - OPUS4-24448 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Horn, Wolfgang A1 - Wiegner, Katharina T1 - Inter-laboratory Study to Check the Performance of Test Chamber Measurements for Product Emission Testing T2 - International Conference on Indoor Air 2011 CY - Austin, TX, USA DA - 2011-06-05 PY - 2011 AN - OPUS4-24138 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiegner, Katharina A1 - Kalus, Sabine A1 - Horn, Wolfgang A1 - Farke, M. T1 - Determination of MVOCs like formic and acetic acid with LC-MS/MS T2 - 15th International Biodeterioration and Biodegradation Symposium IBBS-15 CY - Vienna, Austria DA - 2011-09-19 PY - 2011 AN - OPUS4-24403 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiegner, Katharina A1 - Brödner, Doris A1 - Horn, Wolfgang T1 - Correlation of aldehyde emissions and fatty acids content in pine wood and oriented strand boards T2 - Indoor Air 2011 CY - Austin, TX, USA DA - 2011-06-05 PY - 2011 AN - OPUS4-24139 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeger, Stefan T1 - Zeitaufgelöste Partikelemissionsmessungen an Bürogeräten mit Laserdruckfunktion T2 - 25. Aerosol Technologie Seminar, Fa. Palas GmbH CY - Karlsruhe, Germany DA - 2011-09-12 PY - 2011 AN - OPUS4-24380 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiegner, Katharina A1 - Hahn, Oliver A1 - Kalus, Sabine A1 - Horn, Wolfgang A1 - Farke, M. T1 - Determination of formic and acetic acids in air T2 - Indoor Air 2011 CY - Austin, TX, USA DA - 2011-06-05 PY - 2011 AN - OPUS4-24140 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Wiegner, Katharina A1 - Brödner, Doris A1 - Scheffer, Harald T1 - VOC-Emissions from Plywood Boards T2 - Conference on Indoor Air 2011 CY - Austin, TX, USA DA - 2011-06-05 PY - 2011 AN - OPUS4-24142 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bücker, Michael A1 - Torge, Manfred A1 - Feldmann, Ines A1 - Seeger, Stefan T1 - Staubbelastung im Spalt zwischen Original und Außenschutzverglasung T2 - Abschlussveranstaltung des DBU-Evaluierungsprojektes CY - Stendal, Germany DA - 2011-06-08 PY - 2011 AN - OPUS4-25149 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiegner, Katharina A1 - Horn, Wolfgang A1 - Jann, Oliver A1 - Hahn, Oliver A1 - Farke, M. T1 - BEMMA Bewertung von Emissionen aus Materialien für Museumsausstattungen T2 - EXPONATEC COLOGNE 2011 CY - Cologne, Germany DA - 2011-11-15 PY - 2011 AN - OPUS4-24782 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mull, Birte A1 - Horn, Wolfgang A1 - Wiegner, Katharina T1 - Analytik von Bioziden in Kunst- und Kulturgut T2 - Exponatec Cologne CY - Cologne, Germany DA - 2011-11-16 PY - 2011 AN - OPUS4-24793 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Maiwald, Michael A1 - Daum, Werner T1 - Trends in der prozessanalytischen Messtechnik N2 - Eine gleich bleibend effektive Nutzung von Anlagen, Rohstoffen und Energie in Verbindung mit der optimalen Prozessführung sind die wichtigsten Voraussetzungen für globale Wettbewerbsvorteile der Prozessindustrie. Unternehmen aus den Bereichen Chemie, Pharmazie, Petrochemie, Gasverarbeitung, Lebensmittel-, Zellstoff-, Papier-, Glas-, Stahl- und Zementherstellung sowie ihren Zulieferern haben den Einsatz zuverlässiger Prozessautomation für eine gute Prozessführung erkannt. Überlegene Verfahren stützen sich zunehmend auf prozessanalytische Messtechnik zur Kontrolle und präventiven Sicherstellung der geforderten Produktqualität. Gleichzeitig ermöglicht sie eine ständige Verbesserung des Wissens über den Prozess und erhöhen die Prozess- und Anlagensicherheit. PY - 2011 DO - https://doi.org/10.1524/teme.2011.9026 SN - 0340-837X SN - 0178-2312 SN - 0171-8096 VL - 78 IS - 12 SP - 547 EP - 548 PB - Oldenbourg CY - München AN - OPUS4-25262 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael T1 - Prozessanalytik: Konzepte und Strategien Prozessanalytik in Flüssigkeiten (Hardwareüberblick) T2 - Prozessanalytik: Konzepte und Strategien CY - Frankfurt am Main, Germany DA - 2011-10-19 PY - 2011 AN - OPUS4-24979 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael T1 - Online NMR-Spektroskopie in der Prozessanalytik T2 - Seminar des Institutes für technische Chemie ( eingeladener Vortrag), Universität Stuttgart CY - Stuttgart, Germany DA - 2011-07-05 PY - 2011 AN - OPUS4-24103 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael T1 - On-line NMR -Spektroskopie in der Prozessanalytik T2 - Moderne Methoden der NMR-Spektroskopie, Universität Tübingen CY - Tübingen, Germany DA - 2011-10-10 PY - 2011 AN - OPUS4-25153 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael T1 - On-line NMR-Spektroskopie in der prozessanalytik T2 - Moderne Methoden der NMR-Spektroskopie, Universität Tübingen CY - Tübingen, Germany DA - 2011-10-10 PY - 2011 AN - OPUS4-24980 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael A1 - Guthausen, G. A1 - Dalitz, F. T1 - Investigations of Flow in Quantitative NMR T2 - EUROMAR2011 CY - Frankfurt am Main, Germany DA - 2011-08-21 PY - 2011 AN - OPUS4-24303 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Altmann, Korinna A1 - Schulze, Rolf-Dieter A1 - Hidde, Gundula A1 - Friedrich, Jörg Florian T1 - Elektrospray-Ionisation (ESI) - Lochfreie elektrophoretische Abscheidung von ultra-dünnen Polymerschichten N2 - Die Elektrospray-Ionisations (ESI)-Vernebelung von Polymerlösungen wird analytisch zur massenspektrometrischen Bestimmung der Molmassen von Makromolekülen genutzt. Dabei werden die Polymermoleküle nach einem speziellen Mechanismus im Hochspannungsfeld unter Normaldruckbedingungen vereinzelt und in das Massenspektrometer überführt. Dieser Prozeß kann auch zur flächigen Abscheidung einzelner Polymermoleküle genutzt werden. Die Struktur und Zusammensetzung sowie die Molmassenverteilung der Polymere bleiben dabei erhalten. Schichten polarer oder ionischer Polymere der Dicke einer Quasi-Monolage bis hin zu mehreren 100 Nanometern können abgeschieden werden. Erwähnenswert ist, daß der ESI-Prozeß zu den elektrophoretischen Verfahren gehört, was die Ausbildung lochfreier Schichten auf elektrisch leitenden Substraten nicht nur auf der der Spraydüse zugewandten Seite ermöglicht, sondern auch auf der abgeschatteten Rückseite. Dieses Verhalten wurde zur vollständigen ESI-Umhüllung von dichtgepackten Kohlenstoff-Faser-Bündeln mit haftvermittelnden Polymerschichten ausgenutzt. PY - 2011 DO - https://doi.org/10.1002/vipr.201100471 SN - 0947-076X SN - 1522-2454 VL - 23 IS - 6 SP - 17 EP - 23 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-25392 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Esslinger, Susanne A1 - Becker, Roland A1 - Maul, Ronald A1 - Nehls, Irene T1 - Hexabromocyclododecane enantiomers: microsomal degradation and patterns of hydroxylated metabolites N2 - The degradation of the enantiomers of α-, β-, and γ-hexabromocyclododecane (HBCD) by phase I metabolism was investigated using induced rat liver microsomes. HBCD isomers were quantified using HPLC-MS/MS (ESI-) after separation on a combination of a reversed phase and a chiral analytical column. The degradation of all six isomers followed first-order kinetics and the estimated half-lives ranged from 6.3 min for both β-HBCD enantiomers to 32.3 min in case of (+)-γ-HBCD. (+)-α- and (–)-γ-HBCD displayed significantly shorter half-lives than their corresponding antipodes. It could be shown that this degradation led to a significant enrichment of the first eluting enantiomers (–)-α- and (+)-γ-HBCD. Individual patterns of mono- and dihydroxylated derivatives obtained from each α- and γ-HBCD enantiomer were seen to be distinctly characteristic. The patterns of monohydroxylated HBCD derivatives detected in liver and muscle tissues of pollack, mackerel and in herring gull eggs were largely similar to those observed in the in vitro experiments with rat liver microsomes. This enabled individual hydroxy-HBCDs to be assigned to their respective parent HBCD enantiomers. KW - Brominated flame retardant KW - Cytochromes KW - Phase I metabolism KW - Hydroxylation KW - HPLC-MS/MS PY - 2011 DO - https://doi.org/10.1021/es1039584 SN - 0013-936X SN - 1520-5851 VL - 45 IS - 9 SP - 3938 EP - 3944 PB - ACS Publ. CY - Washington, DC AN - OPUS4-23837 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Esslinger, Susanne A1 - Becker, Roland A1 - Jung, Christian A1 - Schröter-Kermani, C. A1 - Bremser, Wolfram A1 - Nehls, Irene T1 - Temporal trend (1988-2008) of hexabromocyclododecane enantiomers in herring gull eggs from the german coastal region N2 - Levels of α-, β-, and γ-hexabromocyclododecane (HBCD) were determined in pooled eggs from herring gulls (Larus argentatus) sampled on three bird sanctuaries near the German North Sea coast between 1988 and 2008 (Mellum and Trischen) and the German Baltic Sea coast between 1998 and 2008 (Heuwiese) and archived by the German Environmental Specimen Bank. Pressurized fluid extraction, gel permeation chromatography, and LC–MS/MS using 13C12-labelled isotope standards and a chiral column were applied. α-HBCD was the dominating diastereomer and ranged between 3.7 and 107 ng g-1 lw while β- and γ-HBCD were throughout close to LOQ. The highest α-HBCD concentration was found in eggs from Mellum sampled in the year 2000. Interestingly, HBCD in eggs from the three islands displayed similar time courses with levels increasing to a peak contamination around 2000 and decreasing levels ever since. Chiral signatures of α-HBCD in eggs differed among the islands but indicated a preferential enrichment of the first eluting enantiomer (-)-α-HBCD. KW - Brominated flame retardant KW - Chiral separation KW - HPLC-ESI-MS/MS KW - Enantiomer-specific bioaccumulation PY - 2011 DO - https://doi.org/10.1016/j.chemosphere.2010.12.047 SN - 0045-6535 SN - 0366-7111 VL - 83 IS - 2 SP - 161 EP - 167 PB - Elsevier Science CY - Kidlington, Oxford AN - OPUS4-23351 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Casperson, Ralf A1 - Dey, Anika A1 - Pohl, Rainer A1 - Thomas, Hans-Martin T1 - "Verortung" der Prüfergebnisse bei der ZfP an Eisenbahnschienen N2 - Das Schienennetz der DB und anderer Bahngesellschaften wird regelmäßig mit Schienenprüfzügen inspiziert. Die mit den Prüfzügen aufgenommenen Messdaten werden offline zu einem späteren Zeitpunkt ausgewertet. Um Prüfbefunde manuell nachprüfen und ggf. Reparaturmaßnahmen einleiten zu können, ist eine möglichst exakte Zuordnung der Befunde zum Prüfort notwendig. Theoretisch ist jeder Ort des Schienennetzes durch Streckennummer, Richtungskennzahl und Kilometrierung exakt beschrieben. In der Praxis treten jedoch bei der Zuordnung diverse Probleme auf: Die Kilometrierung wird während der Prüfung manuell erfasst, indem die Beschriftung der Kilometer- bzw. Hektometertafeln in das Prüfsystem eingegeben und deren Position beim Vorbeifahren per Tastendruck in die Messdaten „eingeblitzt“ wird. Die Hektometertafeln stehen jedoch nicht an der aufgedruckten Position, sondern sind am nächstgelegenen Mast montiert. Dagegen ist die Ungenauigkeit des manuellen „Einblitzens“ vernachlässigbar. Außerdem ist die Kilometrierung nicht immer eindeutig, da nach Umbaumaßnahmen Kilometersprünge (sowohl fehlende als auch doppelte Kilometer) auftreten können. Abhilfe verspricht der Einsatz des satellitengestützten GPS, vorausgesetzt, die Strecken sind exakt vermessen. Um eine ausreichende Positionsgenauigkeit auch bei schlechten Empfangsbedingungen zu erreichen, ist jedoch ein erheblicher Aufwand notwendig. Die Positionsgenauigkeit eines Standard-GPS-Empfängers genügt hier nicht. Es wird ein Verortungssystem hoher Positionsgenauigkeit auf der Basis des GPS vorgestellt, das sich derzeit in der Erprobung befindet. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 PY - 2011 AN - OPUS4-23930 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scharkoi, O. A1 - Esslinger, Susanne A1 - Becker, Roland A1 - Weber, M. A1 - Nehls, Irene T1 - Phase I oxidation of alpha- and gamma-hexabromocyclododecane by cytochrome P450 enzymes: simulation of the steroisomerism of hydroxylated metabolites T2 - DIOXIN 2011 CY - Brussels, Belgium DA - 2011-08-21 KW - Bromierte Falmmschutzmittel KW - Hexabromcyclododecan KW - Cytochrom KW - Metaboliten KW - HPLC KW - Simulation PY - 2011 UR - http://www.dioxin20xx.org/pdfs/2011/1810.pdf SN - 1026-4892 VL - 73 SP - 730 EP - 733 AN - OPUS4-27263 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Riddell, N. A1 - Becker, Roland A1 - Chittim, B. A1 - Emmerling, Franziska A1 - Köppen, Robert A1 - Lough, A. A1 - McAlees, A. A1 - McCrindle, R. T1 - Preparation and X-ray structural characterization of further stereoisomers of 1,2,5,6,9,10-hexabromocyclododecane N2 - Technical 1,2,5,6,9,10-hexabromocyclododecane (HBCD) consists largely of three diastereomers (α-, β-, and γ-HBCD) produced by the trans addition of bromine to cis,trans,trans-cyclododeca-1,5,9-triene (CDT). However, another seven diastereomers are theoretically possible and may be produced by trans addition of bromine across the double bonds of the other three isomers of 1,5,9-CDT. There are indications that small amounts of the minor HBCD isomers may be present in commercial HBCD mixtures or in products containing this brominated flame retardant (BFR). Such minor components may indeed derive from traces of other 1,5,9-CDTs in the cis, trans, trans starting material, however their formation may also be possible through isomerizations during the processing of this BFR or by bioisomerization subsequent to its release into the environment. Two of the seven additional diastereomers (δ- and ε-HBCD) were synthesized previously from trans,trans,trans-CDT. We now report the preparation of the remaining five diastereomers, ζ-, η-, and θ-HBCD from cis,cis,trans-CDT and ι- and κ-HBCD from cis,cis,cis-CDT, and their characterization by 1H NMR spectroscopy and X-ray crystallography. The availability of these further diastereomers of HBCD should aid in determining if the minor isomers are present in commercial samples of this BFR, in products containing HBCDs, or in environmental samples. We have also carried out an X-ray crystal structure determination on ε-HBCD, so that crystal structures are now available for all 10 HBCD diastereomers. KW - Brominated flame retardants KW - HBCDs KW - Minor isomers KW - X-ray PY - 2011 DO - https://doi.org/10.1016/j.chemosphere.2011.06.014 SN - 0045-6535 SN - 0366-7111 VL - 84 IS - 7 SP - 900 EP - 907 PB - Elsevier Science CY - Kidlington, Oxford AN - OPUS4-24298 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Sauer, Andreas A1 - Scharf, Holger A1 - Becker, Roland T1 - Bericht zum 17. BAM-Ringversuch "Altlasten" N2 - Präsentation der Ergebnisse eines Ringversuchs zur Kompetenzbewertung von Prüflaboratorien auf dem Gebiet der anorganischen und organischen Bodenanalytik. KW - Eignungsprüfung KW - Boden KW - PAK KW - MKW KW - AOX KW - Spurenelemente KW - Gesamtcyanid KW - Proficiency testing KW - Soil KW - PAH KW - TPH KW - Trace elements KW - Total cyanide PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-357785 SP - 1 EP - 212 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-35778 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Becker, Roland A1 - Esslinger, S. A1 - Maul, Ronald A1 - Nehls, Irene T1 - Hydroxylierte Derivate des Flammschutzmittels Hexabromcyclododecan: Beiträge zu Charakterisierung und Analytik in Biota T2 - ANAKON 2011 (ETH Zürich) CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23000 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Moser, H. A1 - Roembke, J. A1 - Donnevert, G. A1 - Becker, Roland T1 - Evaluation of biological mehtods for a future methodological implementation of the hazard criterion H14 'ecotoxic' in the European waste list (2000/532/EC) N2 - The ecotoxicological characterization of waste is part of its assessment as hazardous or non-hazardous according to the European Waste List. For this classification 15 hazard criteria are derived from the Council Directive 91/689/EEC on hazardous waste. Some of the hazard criteria are based on the content of dangerous substances. The criterion H14 'ecotoxic' lacks of an assessment and testing strategy and no specific threshold values have been defined so far. Based on the recommendations of CEN guideline 14735 (2005), an international round robin test (ring test) was organized by the German Federal Environment Agency in order to define suitable test methods for the biological assessment of waste and waste eluates. A basic test battery, consisting of three aquatic and three terrestrial tests, was compiled. In addition, data were submitted for ten additional tests (five aquatic (including a genotoxicity test) and five terrestrial ones). The tests were performed with three representative waste types: an ash from an incineration plant, a soil containing high concentrations of organic contaminants (polycyclic aromatic hydrocarbons) and a preserved wood waste. The results of this ring test confirm that a combination of a battery of biological tests and chemical residual analysis is needed for an ecotoxicological characterization of wastes. With small modifications the basic test battery is considered to be well suitable for the hazard and risk assessment of wastes and waste eluates. All results and documents are accessible via a web-based data bank application. KW - European waste list KW - Waste legislation KW - Bio test battery KW - Ring test structure KW - Interlaboratory comparison KW - Waste ecotoxicity PY - 2011 DO - https://doi.org/10.1177/0734242X10367844 SN - 0734-242X SN - 1096-3669 VL - 29 IS - 2 SP - 180 EP - 187 PB - Sage CY - London AN - OPUS4-23271 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brehme, Sven A1 - Schartel, Bernhard A1 - Goebbels, Jürgen A1 - Fischer, O. A1 - Pospiech, D. A1 - Bykov, Y. A1 - Döring, M. T1 - Phosphorus polyester versus aluminium phosphinate in poly(butylene terephthalate) (PBT): Flame retardancy performance and mechanisms N2 - Pyrolysis and fire behaviour of a phosphorus polyester (PET-P-DOPO) have been investigated. The glycol ether of the hydroquinone derivative of 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide was used as a reactive halogen-free flame retardant in PET-P-DOPO. PET-P-DOPO is proposed as an alternative to poly(butylene terephthalate) (PBT) with established halogen-free additives. It exhibits a high LOI (39.3%) and achieves V-0 classification in the UL 94 test. Three different mechanisms (flame inhibition, charring and a protection effect by the intumescent char) contribute to the flame retardancy in PET-P-DOPO and were quantified with respect to different fire risks. The fire load was reduced by 66% of the PBT characteristic. The reduction is the superposition of the relative reduction due to flame inhibition (factor 0.625) and charring (factor 0.545). The peak of heat release rate (pHRR) was reduced by 83% due to flame inhibition, charring and the protection properties of the char (factor 0.486). The strength of all three mechanisms is in the same order of magnitude. The intumescent multicellular structure enables the char to act as an efficient protection layer. PBT flame-retarded with aluminium diethylphosphinate was used as a benchmark to assess the performance of PET-P-DOPO absolutely, as well as versus the phosphorus content. PET-P-DOPO exhibits superior fire retardancy, in particular due to the additional prolongation of the time to ignition and increase in char yield. PET-P-DOPO is a promising alternative material for creating halogen-free flame-retarded polyesters. KW - Poly(butylene terephthalate) (PBT) KW - Fire retardancy KW - Aluminium phosphinate KW - 9,10-Dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) PY - 2011 DO - https://doi.org/10.1016/j.polymdegradstab.2011.01.035 SN - 0141-3910 SN - 1873-2321 VL - 96 IS - 5 SP - 875 EP - 884 PB - Applied Science Publ. CY - London AN - OPUS4-23469 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Becker, Roland A1 - Scharkoi, O. A1 - Esslinger, Susanne A1 - Weber, M. A1 - Nehls, Irene T1 - Phase I Oxidation of alpha- and gamma-Hexabromocyclodeodecane by Cytochrome P450 Enzymes: Simulation of the Stereoisomerism of Hydroxylated Metabolites T2 - DIOXIN 2011, 31st International Symposium on Halogenated Persistent Organic Pollutants CY - Brussels, Belgium DA - 2011-08-21 PY - 2011 AN - OPUS4-23823 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Durmaz, V. A1 - Weber, M. A1 - Becker, Roland T1 - Multi-Mode Molecular Dynamics Simulation of the Chromatographic Elution Order of Hexabromocyclododecane Stereoisomers T2 - 25th Molecular Modelling Workshop 2011, Friedrich-Alexander-Universität Nürnberg-Erlangen CY - Nuremberg-Erlangen, Germany DA - 2011-04-04 PY - 2011 AN - OPUS4-23512 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brehme, Sven A1 - Schartel, Bernhard A1 - Bykov, Y. A1 - Ciesielski, M. A1 - Döring, M. A1 - Pospiech, D. A1 - Köppl, T. A1 - Altstädt, V. T1 - Flame retardancy mechanisms and performance of a halogen-free phosphorus polyester in PBT T2 - 22nd Annual Conference on Recent Advances in Flame Retardancy of Polymeric Materials CY - Stamford, CT, USA DA - 2011-05-23 PY - 2011 AN - OPUS4-23827 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Durmaz, V. A1 - Weber, M. A1 - Becker, Roland T1 - Multi-Mode Molecular Dynamics Simulation of the Chromatographic Elution Order of Hexabromocyclododecane Stereoisomers T2 - 25th Molecular Modelling Workshop 2011, Friedrich-Alexander-Universität Nürnberg-Erlangen CY - Nuremberg-Erlangen, Germany DA - 2011-04-04 PY - 2011 AN - OPUS4-23511 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gebert, Antje A1 - Jung, Christian A1 - Becker, Roland A1 - Egel, E. A1 - Gabsch, T. A1 - Nehls, Irene T1 - Analyse der Aminosäurenzusammensetzung in Bindemitteln zentralasiatischer Wandmalereien mittels GC-MS T2 - Berliner Chemie Symposium (Jungchemikerforum) der Humboldt-Universität Berlin CY - Berlin, Germany DA - 2011-04-07 PY - 2011 AN - OPUS4-23502 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mönch, Bettina A1 - Gebert, Antje A1 - Becker, Roland A1 - Nehls, Irene T1 - Analytik von Ethylglucuronid in Haaren - Untersuchungen zum Clean-up wässriger Extrakte T2 - Berliner Chemie Symposium (Jungchemikerforum) der Humboldt-Universität Berlin CY - Berlin, Germany DA - 2011-04-07 PY - 2011 AN - OPUS4-23503 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dey, Anika A1 - Casperson, Ralf A1 - Pohl, Rainer A1 - Thomas, Hans-Martin T1 - Efahrungen mit der Wirbelstromprüfung beim Einsatz an unterschiedlichen Schienenstrahlsorten T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23929 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gebert, Antje A1 - Jung, Christian A1 - Becker, Roland A1 - Nehls, Irene A1 - Gabsch, T. A1 - Egel, E. T1 - Determination of the proteinaceous binder component and soluble nylon preservative in Central Asian mural paintings using GC-MS T2 - Tag der Chemie 2011 CY - Berlin, Germany DA - 2011-07-13 PY - 2011 AN - OPUS4-24001 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mönch, Bettina A1 - Jung, Christian A1 - Becker, Roland A1 - Nehls, Irene T1 - A method of detection of ehtylglucuronide by GC-EI-MS using a cold injection system T2 - Tag der Chemie CY - Berlin, Germany DA - 2011-07-13 PY - 2011 AN - OPUS4-23991 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Becker, Roland A1 - Koon, M. A1 - Helmis, Mario A1 - Wirth, B. A1 - Funke, A. A1 - Mumme, J. T1 - Bewertung von HTC-Kohle für ihre Eignung zur Verbesserung von Bodeneigenschaften T2 - First INTERREG NSR Biochar conference - Biokohle - Klimaretter oder Mogelpackung? Biochar - Climate Savior or Bluff Package? 72. Symposium des ANS e. V., FU BErlin CY - Berlin, Germany DA - 2011-10-05 PY - 2011 AN - OPUS4-24456 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Becker, Roland A1 - Gebert, A. A1 - Jung, Christian A1 - Nehls, Irene A1 - Gabsch, T. A1 - Egel, E. T1 - Determination of the proteinaceous binder component and soluble nylon preservative in Central Asian mural paintings using GC-MS T2 - "Auf Grünwedels Spuren - Restaurierung und Forschung an zentralasiatischen Wandmalereien" (Ausstellung des Museums für Asiatische Kunst, Berlin) CY - Berlin, Germany DA - 2011-12-10 PY - 2011 AN - OPUS4-24703 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wiegner, Katharina A1 - Horn, Wolfgang A1 - Stephan, Ina A1 - Nohr, Michael A1 - Lau, Angelika A1 - Farke, M. A1 - Hahn, Oliver T1 - Überprüfung möglicher mikrobieller Belastungen in Vitrinenluft durch Kleinklimageräte N2 - Unterschiedliche Befeuchtungssysteme für Vitrinen, die die Ausstellungsobjekte bei definierter Luftfeuchtigkeit vor externen Einflüssen wie Staub bewahren sollen, wurden im Hinblick auf die Möglichkeit der potenziellen mikrobiologischen Kontamination untersucht. Ergänzend hierzu wurden Parameter wie pH-Wert und Leitfähigkeit des Wassers im Befeuchter untersucht und die mikrobiellen flüchtigen organischen Verbindungen (MVOC, microbial volatile organic compounds) in der Modellvitrine bestimmt. Die Leitfähigkeitsmessung kann als Indikator für den Verunreinigungsgrad des Wassers dienen, weil sie mit der mikrobiologischen Belastung korreliert. Weiterhin war eine mikrobiologische Belastung der Luft in der Modellvitrine auch bei relativ hoher Verunreinigung des Befeuchtungswassers nicht nachzuweisen. KW - MVOC (microbial volatile organic compounds) KW - Schimmelpilze KW - Kleinklimagerät KW - Vitrinen KW - Essigsäure PY - 2011 SN - 0949-8036 SN - 0039-0771 SN - 1436-4891 VL - 71 IS - 9 SP - 378 EP - 381 PB - Springer-VDI-Verl. CY - Düsseldorf AN - OPUS4-24340 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hübert, Thomas A1 - Tiebe, Carlo A1 - Stephan, Ina T1 - Detection of fungal infestations of wood by ion mobility spectrometry N2 - During their growth on wood many fungi produce characteristic volatile organic compounds as secondary metabolites. These microbial volatile organic compounds (MVOCs) can be used as indicators of fungal growth even when such growth is concealed. In order to investigate the formation of these volatile metabolites on building materials, specimens of pine sapwood on agar media colonized by the dry-rot fungus Serpula lacrymans and a mixture of six moulds were examined. MVOCs from this fungal growth were studied over a period of up to half a year by ion mobility spectrometry (IMS) headspace analysis using a sensitive, portable IMS mini-device. The IMS headspace spectra from the growing fungal specimens obtained during this time span are differed from non-incubated wood specimens and indicate the presence of a mixture of MVOCs. The composition and amount of volatile metabolites of the fungi changed during cultivation. This was confirmed by a principal component analysis (PCA). Identification of different MVOCs in the headspace according to drift time and the mobility of ionized gaseous species in reference to GC-MS investigations were proposed. It was concluded that IMS can be used as a rapid and sensitive on-site method to indicate actively growing fungi concealed within wood. KW - Dry rot KW - Serpula lacrymans KW - Moulds KW - Concealed infestation KW - Ion mobility spectrometry KW - Fungal detection PY - 2011 DO - https://doi.org/10.1016/j.ibiod.2011.03.008 SN - 0964-8305 VL - 65 IS - 5 SP - 675 EP - 681 PB - Elsevier CY - Barking AN - OPUS4-23994 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stephan, Ina A1 - Urban, Klaus ED - Ziegahn, K.-F. T1 - Biozide in synthetischen Materialien N2 - Wann ist es sinnvoll ein Biozid in ein synthetisches Material einzubringen? Wenn dadurch ein Problem gelöst wird. Deshalb sollte bei jeder Versuchsplanung die Frage stehen: Was ist das Problem, das man durch Biozieinsatz lösen will? Wie kann es im Laborversuch dargestellt werden? Konnte der Laborversuch zeigen, dass bei Biozideinsatz das Problem kleiner wird, beziehungsweise nicht mehr existiert? Je höher die Teststufe ist, umso mehr muss der Prüfablauf auf die Praxisbedingungen in der Gebrauchsphase des biozidhaltigen Erzeugnisses abgestimmt werden. Auf Stufe 1 werden in der Regel einzelne Wirkstoffe getestet. Ziel ist, die prinzipielle Wirksamkeit nachzuweisen, um die Ergebnisse für die Zulassung auf die Positivliste biozider Wirkstoffe der Biozidrichtlinie einzureichen. Während auf Stufe 1 bereits Normmethoden unter Einbeziehung einer relevanten Materialmatrix angewendet oder für die Fragestellung adaptiert werden können, ist dies für Stufe 2 oftmals nicht gegeben. Stufe 2 zeichnet sich durch Prüfmethodik mit praxisrelevanten Belastungen zur zeitraffenden Alterung des Biozids in seiner Materialmatrix aus. Hier stellt sich auch die Frage zur Langzeitwirksamkeit. Anstelle eines einzelnen Wirkstoffs wird oftmals ein Gemisch verschiedener Wirkstoffe und zusätzlichen Additiven, die wiederum Einfluss auf beispielsweise die Verteilbarkeit, Stabilität und Bioverfügbarkeit haben können. Es wird also kein Wirkstoff, sondern ein Biozidprodukt geprüft. In dem Biozidprodukt dürfen aber nur Wirkstoffe eingesetzt werden, die im Rahmen der Biozidrichtlinie bereits zugelassen sind und auf der Positivliste zu finden sind. Stufe 3 wird diskutiert im Zusammenhang mit Biozidprodukten mit Außeneffekt. Sie beschäftigt sich mit dem Nachweis von Vorteilen durch die Biozidnutzung. Hier gilt es den Verbraucher- und Umweltschutz gegen den Nutzen der möglichen Wertschöpfung oder auch den Gesundheitsschutz durch Biozideinsatz abzuwägen. T2 - 40. Jahrestagung der GUS 2011 - Umwelteinflüsse erfassen, simulieren, bewerten CY - Stutensee-Blankenloch/Karlsruhe DA - 30.03.2011 KW - Biozide Wirksamkeit KW - Konservierung KW - Kunststoffe KW - Material KW - Prüfung PY - 2011 SN - 978-3-9813136-1-1 IS - V17 SP - 91 EP - 102 PB - DWS Werbeagentur und Verlag GmbH CY - Karlsruhe AN - OPUS4-24269 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Plarre, Rüdiger A1 - Stephan, Ina T1 - Neuerungen im Holzschutz durch angepasste Normungsarbeit N2 - Aufgrund einer dem modernen Holzschutz angepassten Normungsarbeit ergaben sich in den letzten Jahren zahlreiche Neuerungen. Diese betreffen sowohl die allgemeine Regelsetzung des Holzschutzes als auch spezielle Prüfstandards zur Wirksamkeitsbewertung von Holzschutzmitteln und -verfahren. KW - Normung KW - Holzschutz PY - 2011 SN - 0018-3881 VL - 52 IS - 2 SP - 50 EP - 51 PB - DRW-Verl. Weinbrenner CY - Leinfelden-Echterdingen AN - OPUS4-23358 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Stephan, Ina A1 - Askew, P. A1 - Gorbushina, Anna A1 - Grinda, Manfred A1 - Hertel, Horst A1 - Krumbein, W.E. A1 - Müller, R.-J. A1 - Pantke, Michael A1 - Plarre, Rüdiger A1 - Schmitt, G. A1 - Schwibbert, Karin ED - Czichos, Horst ED - Saito, T. ED - Smith, L. T1 - Biogenic impact on materials N2 - Materials as constituents of products or components of technical systems rarely exist in isolation and many must cope with exposure in the natural world. This chapter describes methods that simulate how a material is influenced through contact with living systems such as microorganisms and arthropods. Both unwanted and desirable interactions are considered. This biogenic impact on materials is intimately associated with the environment to which the material is exposed (Materials-Environment Interaction, Chap. 15). Factors such as moisture, temperature and availability of food sources all have a significant influence on biological systems. Corrosion (Chap. 12) and wear (Chap. 13) can also be induced or enhanced in the presence of microorganisms. Section 14.1 introduces the categories between desired (biodegradation) and undesired (biodeterioration) biological effects on materials. It also introduces the role of biocides for the protection of materials. Section 14.2 describes the testing of wood as a building material especially against microorganisms and insects. Section 14.3 characterizes the test methodologies for two other groups of organic materials, namely polymers (Sect. 14.3.1) and paper and textiles (Sect. 14.3.2). Section 14.4 deals with the susceptibility of inorganic materials such as metals (Sect. 14.4.1), concrete (Sect. 14.4.2) and ceramics (Sect. 14.4.3) to biogenic impact. Section 14.5 treats the testing methodology concerned with the performance of coatings and coating materials. In many of these tests specific strains of organisms are employed. It is vital that these strains retain their ability to utilize/attack the substrate from which they were isolated, even when kept for many years in the laboratory. Section 14.6 therefore considers the importance of maintaining robust and representative test organisms that are as capable of utilizing a substrate as their counterparts in nature such that realistic predictions of performance can be made. KW - Materialschutz KW - Biologie KW - Organismus KW - Standard KW - Prüfung PY - 2011 SN - 978-3-642-16640-2 SP - 769 EP - 844 PB - Springer CY - Berlin, Heidelberg AN - OPUS4-24210 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stephan, Ina A1 - Plarre, Rüdiger A1 - Urban, Klaus T1 - Anforderungen an die Wirksamkeitsbewertung von Materialschutzmitteln T2 - BAuA-Fachtagung Zulassung/Registrierung von Biozid-Produkten, Schwerpunkt; "Schutzmittel (Hauptgruppe 2 ohne PA 8)" CY - Dortmund, Germany DA - 2011-10-10 PY - 2011 AN - OPUS4-25305 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naumann, Annette A1 - Stephan, Ina A1 - Braun, Ulrike A1 - Noll, Matthias T1 - Weathering, fungal decay and flame-protection of wood-plastic composites (BAM Innovation Project) T2 - COSP 2011 CY - Berlin, Germany DA - 2011-03-21 PY - 2011 AN - OPUS4-23086 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Körper, Steffen A1 - Göller, Stephan A1 - Krause, Martin A1 - Stephan, Ina T1 - Feuchteabhängigkeit der Ultraschallgeschwindigkeit und des Biegeelastizitätsmoduls für Holz T2 - DGZfP Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24842 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stephan, Ina T1 - Efficacy Testing of PT8 T2 - Biocides 2011, Multinational Conference on Legal Issues and Trade Aspects of Biocidal Products CY - Vienna, Austria DA - 2011-11-29 PY - 2011 AN - OPUS4-25306 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stephan, Ina A1 - Gabsch, T. A1 - Dimke, T. T1 - Ursachen und Auswirkungen von Schimmel an zentralasiatischen Wandmalereien aus dem 5./6. Jh. n. Chr. N2 - Bereits bei der Entdeckung der zentralasiatischen Kultstätten gegen Ende des 19. Jh. durch zahlreiche Expeditionen waren Beschädigungen durch Schimmelpilze in situ festgestellt worden. Die von den deutschen Expeditionen in Zentralasien Vorgefundenen Kultstätten hatten unterschiedliche Erhaltungszustände. Einige Höhlen waren komplett eingestürzt, verschüttet und mußten freigelegt werden. Bei anderen Höhlen waren die Vorhallen zerstört und es tropfte Wasser aus Deckenausbrüchen und Rissen im Felsgestein. Albert Grünwedel dokumentiert in seinem Buch „Kultstätten" auf S. 148 die Auffindung der sog. Malerhöhle (Höhle Nr. 17) und schreibt hierzu: „Diese alte und schöne Höhle war völlig durch eine Schlammrunse verschlossen und unsichtbar... Als sie entdeckt wurde, waren die Wände dick mit Schimmel belegt. Da zu befürchten war, daß die Bilder abfallen würden, wurde nur eine kleine Öffnung gemacht, um der Luft Zutritt zu gewähren, da auch der Aufenthalt in der Höhle infolge des Geruchs der Pilze unmöglich war. Diese Öffnung wurde allmählich erweitert und als der Schimmelbeschlag getrocknet war, wurden die Wände mit chinesischem Branntwein gewaschen. Dadurch fiel der aufgetrocknete Schimmel ab und es wurde möglich, sich in der Höhle aufzuhalten." KW - Schimmel KW - Wandmalerei KW - Kulturgut PY - 2011 SN - 1433-3848 IS - 186 SP - 29 EP - 35 PB - Müller-Straten CY - München AN - OPUS4-25330 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naumann, Annette A1 - Noll, Matthias A1 - Stephan, Ina A1 - Braun, Ulrike T1 - Material resistance of flame-protected wood-plastic composites against weathering and fungal decay - BAM Innovation Project T2 - Forstbotanisches Seminar CY - Göttingen, Germany DA - 2011-05-09 PY - 2011 AN - OPUS4-25308 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübert, Thomas A1 - Shabir Mahr, Muhammad A1 - Unger, Brita A1 - Stephan, Ina A1 - Bücker, Michael A1 - Militz, H. T1 - Sol-Gel based impregnation for multifunctional protection of wood T2 - 16th International Sol-Gel Conference CY - Hangzhou, China DA - 2011-08-28 PY - 2011 AN - OPUS4-28813 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seefeldt, Henrik A1 - Braun, Ulrike A1 - Hofmann-Böllinghaus, Anja T1 - Influence of structure, wood content, moisture and additives on the burning behaviour of wood plastic composites T2 - Fire and materials 2011 - 12th International conference and exhibiton CY - San Francisco, CA, USA DA - 2011-01-31 PY - 2011 SP - 1 EP - 10 PB - Interscience Communications AN - OPUS4-24650 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Zum Einfluss des Mischungsentwurfs und des Fließmittels auf temperaturbedingte Veränderungen der Rheologie von SVB T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Fließmittel KW - Polycarboxylatether KW - Selbstverdichtender Beton KW - Temperatureffekte KW - Rheologie PY - 2011 SN - 978-3-9814281-0-0 SP - 40 EP - 49 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25194 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Zum Einfluss des Mischungsentwurfs und des Fließmittels auf temperaturbedingte Veränderungen der Rheologie von SVB T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25129 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marinescu, M.V.A. A1 - Schmidt, Wolfram A1 - Priebe, Nsesheye Susan A1 - Uzoegbo, H.C. A1 - Stipanovic Oslakovic, I. A1 - Kumaran, G.S. A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten A1 - Rogge, Andreas T1 - Recent developments and perspectives regarding the standardisation and quality surveillance of cement in the east, central and south african region N2 - The cement and concrete market in East, Central and Southern Africa is highly fragmented. The concrete industry in this area consists of multiple parties, including producers and suppliers of construction materials, formal and informal contractors, engineers and architects, unions of trades persons and workmen, governmental bodies and formal institutions of research and education. All these institutions mostly do not interact adequately, which makes building with cementitious materials susceptible to damage and failures. Completely opposed to the situation in Europe or North America, cement in Africa is often unaffordable, while manpower is cheap, which results in a questionable economisation of cement. Typically, there is not sufficient awareness of methods to sensibly reducing the cement content in concrete or replace Ordinary Portland Cement by adequate alternative materials. Research activities in this field of technology are often missing completely. Only few countries in the area, such as South Africa, are exempted from these issues. This paper presents the SPIN project, which is a joint project of a consortium of 8 African and 3 European partners within the ACP Science and Technology Programme. The project is funded by the EC and ACP Secretariat is the project body. The main objective of the current project is to strengthen the cement and concrete industry in the East and Central African regions. The project shall generate reasonable solution strategies to implement clean, safe and sustainable cement and concrete technology on the African continent, including general and specific guidelines for sensible application. Furthermore it shall be the kick-off for future projects, research activities and the world-wide expansion of a European-African network. The paper addresses special problems the cement and concrete market in Eastern, Central and Southern African countries has to face. Several options are presented in detail, which shall help overcoming the current situation. Customized solutions for the African market include rational methods for reducing the amount of cement used and the replacement of Ordinary Portland Cement with cheaper alternatives. The use of recycled concrete through a new and economically effective method, as well as the opportunity of using locally available resources is also discussed. T2 - 13th International congress on the chemistry of cement CY - Madrid, Spain DA - 03.07.2011 KW - Africa KW - Clean and safe cement production KW - Scientific network PY - 2011 SN - 978-84-7292-400-0 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. SP - 1 EP - 6 AN - OPUS4-24041 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Influence of environmental temperatures on the performance of polymeric stabilising agent in fresh cementitious materials N2 - Stabilising admixtures are commonly used additives in repair mortars and grouts. Beyond this, such type of admixture is increasingly used in concrete and other cementitious materials. In particular when fresh mortar or concrete properties have to be adjusted reliably, stabilising agents can be beneficially used to improve workability and robustness of the mixture. The mode of operation of these admixtures varies, rather affecting either the liquid phase or the solid particles in the dispersion, both causing strong interactions with the mortar or concrete system, and significant changes in their rheological behaviour. Furthermore, these are strongly affected by the environmental temperature during the casting process. In the paper the effect of temperature on the performance of stabilising agents in cementitious systems is presented and how performance changes affect fresh and hardening mortar or concrete properties. Particular attention is placed on interactions between stabilising agents and superplasticizers. Results are discussed with special focus on self-compacting concrete. KW - Biopolymers KW - Cementitious materials KW - Polycarboxylate ether KW - Rheology KW - Setting KW - Stabilising agent KW - Starch ether KW - Self-compacting concrete KW - Superplasticizer PY - 2011 DO - https://doi.org/10.4028/www.scientific.net/KEM.466.97 SN - 1013-9826 VL - 466 SP - 97 EP - 104 PB - Trans Tech Publ. CY - Aedermannsdorf AN - OPUS4-22853 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Priebe, Nsesheye Susan A1 - Kühne, Hans-Carsten A1 - Rogge, Andreas A1 - Marinescu, M. A1 - Brouwers, J. A1 - Uzoegbo, H. A1 - Oslakovic, I. A1 - Kumaran, S. T1 - Recent Developments and Perspectives Regarding the Standardisation and Quality Surveillance of Cement in the East, Central and South African Region T2 - XIII ICCC - International Congress on the Chemistry of Cement CY - Madrid, Spain DA - 2011-07-03 PY - 2011 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. AN - OPUS4-24020 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Brouwers, J. A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Correlation between setting, heat evolution, and deformations of cementitious binder systems depending on type and amount of superplasticizer T2 - XIII ICCC - International Congress on the Chemistry of Cement CY - Madrid, Spain DA - 2011-07-03 PY - 2011 AN - OPUS4-24019 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten T1 - Robustness improvement for Concrete at challenging climatic conditions T2 - Vorlesung im Rahmen des Kick-Off Meetings zum SPIN Projekt "Spearhead Network for Innovative, Clean and Safe Cement and Concrete Technologies" CY - Kigali, Rwanda DA - 2011-01-18 PY - 2011 AN - OPUS4-23183 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram T1 - Einfluss der Polymerstruktur von Stabilisierern auf die Rheologie von selbstverdichtendem Beton und Mörtel T2 - 20. Kolloquium und Workshop "Rheologische Messungen an mineralischen Baustoffen" CY - Regensburg, Germany DA - 2011-03-01 PY - 2011 AN - OPUS4-23313 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram T1 - Robustness improvement of early age properties of SCC by optimised adjustment of mixture composition and admixtures T2 - International Workshop on Self-Compacting Concrete CY - Belfast, Northern Ireland DA - 2011-04-19 PY - 2011 AN - OPUS4-23715 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram T1 - Challenges of the African environmental conditions for concrete mixture composition N2 - Concrete technology was exposed to a rapid development during the last three decades. For the longest time in its history, concrete was considered as a three component System consisting of aggregates, which are bound by the hardened cement paste consisting of hydrated cement. Traditionally, the only way of adjusting the consistency of concrete was using well adjusted aggregates and grading curves and adding excess water to the concrete, accepting that the latter in return reduces strength and durability. During the last three decades, however, concrete has developed further from a three component System towards an (at least) five component system, since the use of mineral additions and Chemical admixtures has become state of the art. Both components are able to enhance the workability, the compactability, and the density of the microstructure with effects on strength, ductility and durability, while cement can be saved in parallel. Due to reasonable use of admixtures and additions, concrete can be designed to match mechanically high performance specifications. Traditionally, cement paste was considered the weakest component in concrete. Flowever, in modern concrete a good paste composition can yield highest performance, passing the role of the mechanical bottleneck towards the aggregates. T2 - Workshop cement and concrete for Africa CY - Berlin, Germany DA - 17.08.2011 KW - Cement KW - Concrete KW - Mixture composition KW - Africa KW - Climatic conditions PY - 2011 SN - 978-3-9814281-4-8 SP - 37 EP - 49 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-24780 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Correlation between setting, heat evolution, and deformations of cementitious binder systems depending on type and amount of superplasticizer N2 - Today polycarboxylate ether based superplasticizer (PCE) is commonly used in concrete technology when high flow properties and water reduction are specified. The ionic strength of the polymers’ backbones determines the adsorption behaviour of polymers on clinker and early hydration products. The amount of required polymers for specified flow properties and the performance over the time of casting is thus determined by the molecular structure of the superplasticizer. The time depending consumption of polycarboxylate ether polymers strongly affects the reaction of aluminates and sulphate ions as well as the hydration process in general. Hence, the choice of polymers for particular flow properties greatly affects the very early properties of cementitious materials such as setting, heat evolution and autogenous deformations. In order to better understand how PCEs influence the early properties, mixes from cement, limestone filler, viscosity modifying agent and water were varied with a high and a low charge density superplasticizer in differing amounts. Results are presented from measurements with an automatic Vicat device, an isothermal heat flow calorimeter, and shrinkage cones. Tests were conducted at 5, 20, and 30 °C. It is shown that in presence of PCE the final set correlates well with the inflexion point of the heat flow curve, which emphasises the interrelation between C-S-H formation and setting. No such clear correlation can be found for the initial set, which is attributed to the fact that the initial set is rather a rheological than a structural phenomenon, so that other effects overlap with C-S-H formation. The results demonstrate that for a given polymer concentration low charge density polymers yield earlier setting than high charge polymers. However, this influence is overridden by the influence of the total amount of polymers in a cementitious system. Since PCE is typically added according to rheological specifications, and low charge PCE typically requires higher amounts of polymers than high charge PCE for comparable flow performance, low charge PCE retards setting more than high charge PCE. The paper furthermore points out that there is no significant influence of the polymer type or amount on the early deformations. Since type and amount strongly affect the hydration, it is demonstrated that early setting causes higher strain after the final set. It is hence concluded that higher PCE solid contents reduce the risk of early cracks that occur at time of setting, when a solid structure has already been formed but without resistance against cracks yet. T2 - 13th International congress on the chemistry of cement CY - Madrid, Spain DA - 03.07.2011 KW - Polycarboxylate superplasticizer KW - Setting KW - Heat evolution KW - Autogenous deformation KW - Self-compacting concrete KW - Calorimetry PY - 2011 SN - 978-84-7292-400-0 SP - 384 EP - 391 AN - OPUS4-24097 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Priebe, Nsesheye Susan A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten T1 - The SPIN project N2 - Globally, cement and concrete experts are at the cutting-edge to sustainable, green, healthy but nonetheless high-performance concrete. In the present age, concrete is not yet well established in Africa, which öfters the unique opportunity to build up a cement and concrete market based on the highest available state of technology. As this industry needs high level expertise, a central issue in implementation of skilled technology is cross-linking research institutions and laboratories. It should not be neglected that concrete is a product with comparably low transport ranges, which means that an improved concrete market will mainly support the local economy without exceeding financial drains to the international market, thus fostering the fight against poverty, which is an urgent need in most African countries. The SPIN project highlights recent developments in the field of cement and concrete research with impact on the local and global economy. Challenges, future developments and opportunities for the African construction industry are in the focus. The SPIN project is funded by the European Commission (EC) and supported by the African, Caribbean and Pacific (ACP) Group of States under the project body of the ACP Science and Technology Programme. SPIN is acronym for “Spearhead network for Innovative, Clean and Safe Cement and Concrete Technologies”. The project aims to cross-link experts with industry and policy making bodies, aiming to establish sustainable cement and concrete construction in Africa. T2 - Workshop cement and concrete for Africa CY - Berlin, Germany DA - 17.08.2011 PY - 2011 SN - 978-3-9814281-4-8 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. SP - 5 EP - 9 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-24778 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Priebe, Nsesheye Susan A1 - Kühne, Hans-Carsten T1 - SPIN- Spearhead network for innovative,clean and safe cement & concrete technologies N2 - Worldwide, cement and concrete experts are at the cutting-edge to sustainable, green, healthy but nonetheless high-Performance concrete. The current relatively low development of the cement and concrete industry in Africa offers the unique opportunity to start directly on the best achievable and sustainable Level, if only Expertise is sufficiently available. It should not be neglected that concrete is a product with comparably low Transport ranges, which means that an improved concrete market will mainly Support the local economy without exceeding financial Drains to the international market, thus fostering the fight against poverty, which is an urgent Need in most African countries. T2 - Workshop Cement and Concrete for Africa CY - Berlin, Germany DA - 17.08.2011 PY - 2011 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. AN - OPUS4-24728 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram T1 - The SPIN network for knowledge-driven, sustainable and clean cement and concrete technology in Africa - Practical experiences from international research cooperation between Europe and Africa T2 - 2nd Joint Stakeholder Conference of the EDULINK and the ACP Science and Technology (ACP S&T) programmes CY - Brussels, Belgium DA - 2011-10-26 PY - 2011 AN - OPUS4-24743 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Gluth, Gregor A1 - Kühne, Hans-Carsten T1 - LightSHIP Lightweight Construction - Scientific Cooperation for Housing with Innovative Panel Technology T2 - Workshop Cement and Concrete for Africa, BAM CY - Berlin, Germany DA - 2011-08-17 PY - 2011 AN - OPUS4-24727 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Vasilic, Ksenija A1 - Kühne, Hans-Carsten A1 - Meng, Birgit A1 - Roussel, Nicolas T1 - Modelling of fresh SCC flow through reinforced sections T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25128 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meng, Birgit A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten T1 - Aktuelle Forschungsansätze zur Rheologie von Frischbeton T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25130 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram T1 - Challenges of the African Environmental Conditions for Concrete Mixture Compostion T2 - Workshop "Cement and Concrete for Africa", BAM CY - Berlin, Germany DA - 2011-08-17 PY - 2011 AN - OPUS4-24726 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kühne, Hans-Carsten A1 - Priebe, Nsesheye Susan A1 - Schmidt, Wolfram A1 - Uzoegbo, H. C. T1 - Baupraxis und Infrastrukturentwicklung im Hinblick auf die Betonindustrie in Ost- und Südafrika N2 - Der Bausektor stellt in Afrika traditionell eine der stabileren Quellen für den Arbeitsmarkt dar. Durch ständige Wechsel in der Politik wurden jedoch in zahlreichen Ländern Einschnitte bei den öffentlichen Investitionen sowie ein Rückgang der Beschäftigtenzahlen im Privatsektor beobachtet. Darüber hinaus konnte eine Verlagerung von offiziell tätigen und registrierten hin zu nicht registrierten Bauunternehmen festgestellt werden. Zahlreiche Bauunternehmen bieten Dienstleistungen an, die sie nicht ständig ausführen oder für die sie sich das erforderliche Gerät leihen müssen. Einer im Jahre 2000 hinsichtlich der Situation in Tansania veröffentlichten Studie zufolge verfügen nur etwa 15 % der Unternehmen, die Betonbauarbeiten anbieten, über einen eigenen Betonmischer. Die auf dem afrikanischen Kontinent angewandten Baupraktiken im Betonbau weichen erheblich voneinander ab. Während Südafrika über eine fortgeschrittene Technologie und eine hoch entwickelte Infrastruktur im Hinblick auf die Zement- und Betonindustrie verfügt, sind Zement und Beton in den ostafrikanischen Ländern, insbesondere in jenen, die in den 90er Jahren des vergangenen Jahrhunderts von schweren Bürgerkriegen erschüttert wurden, kaum verfügbar und zählen keinesfalls zu den in der täglichen Baupraxis verwendeten Baustoffen. Hier wird auf einheimische Baumethoden, bei denen vorwiegend Holz verwendet wird, zurückgegriffen. Dieses wird durch Abholzung gewonnen, was schließlich zur Rodung ganzer Waldgebiete führt. Die ohne entsprechende Planung, Genehmigung und Erschließung errichteten Siedlungen in Südafrika und Kenia veranschaulichen erschreckend, wie einstmals von grüner Vegetation bedeckte Landstriche in künstliche, wüstenartige Landschaften verwandelt wurden. PY - 2011 SN - 1439-7706 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. VL - 3 SP - 32 EP - 37 PB - ad-media-Verl. CY - Köln AN - OPUS4-25361 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kühne, Hans-Carsten A1 - Priebe, Nsesheye Susan A1 - Schmidt, Wolfram A1 - Uzoegbo, H. C. T1 - Building practice and concrete infrastructure development in eastern and southern Africa N2 - The construction sector has traditionally been a source of employment in African regions. However, due to policy changes, cut backs in public investments as well as a fall in the number of employments in the private sector have been observed in many countries. Furthermore a shift from registered companies to informal contractors could be noticed. Many contractors offer services they do not provide permanently or for which the required equipment has to be borrowed. A study that was published in 2000 about the situation in Tanzania pointed out that only ca. 15% of the enterprises that offer concrete works own a concrete mixer. The building practice with concrete varies widely over the African continent. Whereas the level of technology and the infrastructure for cement and concrete in South Africa is elaborate, in East Africa and particularly those that were heavily suffering from civil war during the nineties of the last century, the availability of cement and concrete is poor and these materials are far from being everyday building practice. Most of the population relies on indigenous forms of construction requiring wood obtained from felling of forest trees and ultimately contributing to de-forestation. Informal settlements in South-Africa and Kenya are literal evidence where originally green natural vegetation has been turned into artificial desert-like landscapes. PY - 2011 SN - 1437-9023 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. VL - 3 SP - 32 EP - 37 PB - ad-media-Verl. CY - Köln AN - OPUS4-25360 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Priebe, Nsesheye Susan A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten ED - Rogge, A. ED - Meng, B. T1 - Cement and concrete development in Africa: the role of the SPIN project T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 PY - 2011 SN - 978-3-9814281-0-0 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. SP - 339 EP - 344 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25172 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meng, Birgit A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten ED - Rogge, A. ED - Meng, B. T1 - Aktuelle Forschungsansätze zur Rheologie von Frischbeton T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Baustoffe KW - Beton KW - Frischbeton KW - Rheologie PY - 2011 SN - 978-3-9814281-0-0 SP - 33 EP - 39 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25195 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Barthel, Maria A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Betonpflastersteine mit erweiterten Leistungsmerkmalen T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 PY - 2011 SN - 978-3-9814281-0-0 N1 - Geburtsname von Barthel, Maria: Meinel, M. - Birth name of Barthel, Maria: Meinel, M. SP - 194 EP - 203 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25182 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Priebe, Nsesheye Susan A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten T1 - Cement and Concrete Development in Africa: The Role of the SPIN Project T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. AN - OPUS4-25251 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Barthel, Maria A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Betonpflastersteine mit erweiterten Leistungsmerkmalen T2 - 52. DAfStb-Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 N1 - Geburtsname von Barthel, Maria: Meinel, M. - Birth name of Barthel, Maria: Meinel, M. AN - OPUS4-25236 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weller, Michael G. A1 - Ramin, Steffen A1 - Walter, Astrid T1 - Detection of explosives by bioanalytical techniques T2 - Potsdam Days on Bioanalysis 2011 CY - Potsdam, Germany DA - 2011-11-09 PY - 2011 AN - OPUS4-24952 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schwarz, Gunnar A1 - Beck, S. A1 - Weller, Michael G. A1 - Linscheid, M.W. T1 - MeCAT - new iodoacetamide reagents for metal labeling of proteins and peptides N2 - Besides protein identification via mass spectrometric methods, protein and peptide quantification has become more and more important in order to tackle biological questions. Methods like differential gel electrophoresis or enzyme-linked immunosorbent assays have been used to assess protein concentrations, while stable isotope labeling methods are also well established in quantitative proteomics. Recently, we developed metalcoded affinity tagging (MeCAT) as an alternative for accurate and sensitive quantification of peptides and proteins. In addition to absolute quantification via inductively coupled plasma mass spectrometry, MeCAT also enables sequence analysis via electrospray ionization tandem mass spectrometry. In the current study, we developed a new labeling approach utilizing an iodoacetamide MeCAT reagent (MeCAT-IA). The MeCAT-IA approach shows distinct advantages over the previously used MeCAT with maleinimide reactivity such as higher labelling efficiency and the lack of diastereomer formation during labeling. Here, we present a careful characterization of this new method focusing on the labeling process, which yields complete tagging with an excess of reagent of 1.6 to 1, less complex chromatographic behavior, and fragmentation characteristics of the tagged peptides using the iodoacetamide MeCAT reagent. KW - Quantitative proteomics KW - Mass spectrometry KW - Metal labeling KW - Stable isotope labeling KW - Lanthanide DOTA KW - Metall-Markierung KW - Reagenzien KW - Protein-Quantifizierung KW - Lanthaniden KW - Multiplexing PY - 2011 DO - https://doi.org/10.1007/s00216-011-5189-7 SN - 1618-2642 SN - 1618-2650 VL - 401 IS - 4 SP - 1203 EP - 1209 PB - Springer CY - Berlin AN - OPUS4-23949 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann, Andreas A1 - Bahlmann, Arnold A1 - Weller, Michael G. A1 - Panne, Ulrich A1 - Schneider, Rudolf T1 - Determination of Carbamazepine, Sulfamethoxazole and Cocaine in Surface Water in Berlin by LC-MS/MS and ELISA T2 - HPLS-Tagung CY - Budapest, Hungary DA - 2011-06-19 PY - 2011 AN - OPUS4-23938 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kraus, Werner A1 - Schneider, Rudolf A1 - Weller, Michael G. A1 - Panne, Ulrich A1 - Emmerling, Franziska A1 - Walter, Astrid T1 - Triacetone Triperoxide Hapten Structure for the Development of Antibodies T2 - Joint Meeting DGK, DMG and ÖMG 2011 CY - Salzburg, Austria DA - 2011-09-20 PY - 2011 AN - OPUS4-23983 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hecht, Mandy A1 - Weller, Michael G. A1 - Rurack, Knut T1 - Synthesis and Characterization of Red-emitting Silica-based Dye-doped Nanoparticles T2 - Hybrid Materials 2011 CY - Strasbourg, France DA - 2011-03-06 PY - 2011 AN - OPUS4-23934 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schwarz, G. A1 - Weller, Michael G. A1 - Beck, S. A1 - Linscheid, M. T1 - MeCAT - new iodoacetamide reagents for metal labeling of proteins and peptides T2 - Metallomics Conference 2011 CY - Münster, Germany DA - 2011-06-15 PY - 2011 AN - OPUS4-24006 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schwarz, G. A1 - Weller, Michael G. A1 - Beck, S. A1 - Linscheid, M. T1 - MeCAT - Reagents for cysteine labeling of proteins and peptides T2 - 3rd International Symposium on Metallomics CY - Münster, Germany DA - 2011-06-15 PY - 2011 AN - OPUS4-26039 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schwarz, G. A1 - Weller, Michael G. A1 - Beck, S. A1 - Linscheid, M. T1 - MeCAT - Iodine reactivity for cysteine labeling of proteins and peptides T2 - Annual meeting DGMS CY - Dortmund, Germany DA - 2011-09-21 PY - 2011 AN - OPUS4-26041 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Behnke, Thomas A1 - Würth, Christian A1 - Hoffmann, Katrin A1 - Hübner, Martin A1 - Panne, Ulrich A1 - Resch-Genger, Ute T1 - Encapsulation of hydrophobic dyes in polystyrene micro- and nanoparticles via swelling procedures N2 - Aiming at the derivation of a generalized procedure for the straightforward preparation of particles fluorescing in the visible and near-infrared (NIR) spectral region, different swelling procedures for the loading of the hydrophobic polarity-probe Nile Red into nano- and micrometer sized polystyrene particles were studied and compared with respect to the optical properties of the resulting particles. The effect of the amount of incorporated dye on the spectroscopic properties of the particles was investigated for differently sized beads with different surface chemistries, i.e., non-functionalized, aminomodified and PEG-grafted surfaces. Moreover, photostability and leaking studies were performed. The main criterion for the optimization of the dye loading procedures was a high and thermally and photochemically stable fluorescence output of the particles for the future application of these systems as fluorescent labels. KW - Fluorescence KW - Nile red KW - Polystyrene KW - Nanoparticles KW - Microparticles KW - Encapsulation KW - Swelling PY - 2011 DO - https://doi.org/10.1007/s10895-010-0632-2 SN - 1053-0509 SN - 1573-4994 VL - 21 IS - 3 SP - 937 EP - 944 PB - Plenum Publ. Corp. CY - New York, NY AN - OPUS4-22692 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Panne, Ulrich A1 - Riedel, Jens A1 - Höhse, Marek A1 - Kadenkin, Alexander A1 - Demidov, Alexandr T1 - Towards Quantitative LIBS: Modeling and Chemometrics T2 - EMSLIBS 2011 CY - Izmir, Turkey DA - 2011-09-11 PY - 2011 AN - OPUS4-24122 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Panne, Ulrich T1 - Spectrochemical Analysis: Tools and Toys!? T2 - GDCH-Vortrag, Wintersemester, Universtät Essen-Duisburg CY - Essen, Germany DA - 2011-02-02 PY - 2011 AN - OPUS4-22140 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rackwitz, Vanessa A1 - Procop, M. A1 - Bjeoumikhova, S. A1 - Panne, Ulrich A1 - Hodoroaba, Vasile-Dan T1 - A routine procedure for the characterisation of polycapillary X-ray semi-lenses in prallelising mode with SEM/EDS N2 - The accurate knowledge of the properties of polycapillary X-ray semi-lenses has a significant influence on the quantitative results in a widespread field of applications involving microfocus X-ray beams. A routine procedure for the characterisation of a polycapillary X-ray semi-lens with a scanning electron microscope (SEM) having attached an energy dispersive spectrometer (EDS) is presented in this paper. A key issue of the procedure consists of fitting the semi-lens in front of the EDS for spectra acquisition. Relevant semi-lens parameters such as focal distance, full width at half maximum (FWHM) of the acceptance area, and transmission are determined in parallelising mode of the semi-lens. Special attention has been paid to the calculation of the transmission. KW - Polycapillary X-ray optics KW - Semi-lens KW - Parallelising mode KW - SEM KW - EDS KW - Acceptance area KW - FWHM KW - Transmission KW - Focal distance KW - XRF PY - 2011 DO - https://doi.org/10.1039/c0ja00135j SN - 0267-9477 SN - 1364-5544 VL - 26 IS - 3 SP - 499 EP - 504 PB - Royal Society of Chemistry CY - London AN - OPUS4-23555 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Barthel, Mathias A1 - Seeger, Stefan A1 - Rothhardt, Monika A1 - Wilke, Olaf A1 - Horn, Wolfgang A1 - Juritsch, Elevtheria A1 - Hahn, Oliver A1 - Jann, Oliver T1 - Erfassung der Zahl feiner und ultrafeiner Partikel aus Bürogeräten während der Druckphase zur Entwicklung eines Prüfverfahrens für das Umweltzeichen Blauer Engel für Bürogeräte mit Druckfunktion - Zusammenfassung N2 - Vor dem Hintergrund der anhaltenden öffentlichen Diskussion um mögliche gesundheitliche Risiken von Ultrafein- und Feinstaubemissionen aus Bürogeräten mit Laserdruckfunktion (LPD, Laser Printing Device) wurde vom Umweltbundesamt ein Forschungsvorhaben zur Entwicklung einer Prüfprozedur für die Quantifizierung der emittierten Partikel durch Zählung unter Standardbedingungen in Emissionsmesskammern, sowie zur physikalischen und chemischen Charakterisierung dieser Aerosole initiiert. Als Ergebnis konnte die Partikelzählung in den Entwurf des Prüfverfahrens für die Bestimmung von Emissionen (RAL-UZ-122, Anhang S-M) des Umweltzeichens "Blauer Engel" für Bürogeräte sowie in den Prüfstandards ECMA-328 und den Entwurf der ISO/IEC 28360 integriert werden. Die Methode wurde in einem internationalen Ringversuch erfolgreich getestet. Auf dieser Basis können Vergabekriterien und -werte für die Emission von Fein- und Ultrafeinpartikeln im Rahmen der Vergabe des Umweltzeichens Blauer Engel vereinbart und Produktprüfungen vorgenommen werden. KW - Blauer Engel KW - Bürogeräte mit Druckfunktion KW - Partikelemission KW - RAL-UZ 122 PY - 2011 VL - Förderkennzeichen UFOPLAN 3708 95 301 SP - 1 EP - 8 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-59863 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tag, Mathias A1 - Bresch, Harald A1 - Seeger, Stefan A1 - Möhle, N. A1 - Aufderheide, M. T1 - Experimental study of aerosol cell exposure with an air-liquid interface T2 - Congress of the European Societies of Toxicology CY - Paris, France DA - 2011-08-28 PY - 2011 N1 - Geburtsname von Tag, Mathias: Deutscher, M. - Birth name of Tag, Mathias: Deutscher, M. AN - OPUS4-24405 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wienold, Julia A1 - Traub, Heike A1 - Bresch, Harald A1 - Seeger, Stefan A1 - Recknagel, Sebastian A1 - Kipphardt, Heinrich T1 - Effort on calibration of infrared spark ablation of copper with synthetic copper standards N2 - Two types of copper samples, compact certified copper reference materials and calibration samples prepared from liquid doped, pressed copper powders, were studied in terms of accuracy of obtained calibration functions originating from infrared spark ablation. Additionally, corresponding particle size distributions of the aerosols from infrared spark ablation were recorded. It is shown that the differences in quantification results, originating from the two sets of calibration functions, could not mainly be ascribed to different particle size distributions of the two copper sample types. Possible other causes, as different ablation rates, parts of melting and differences of the chemical constitutions of the two sample types were explored. KW - Calibration KW - Spark ablation KW - Synthetic standard KW - Particle size distribution KW - Fractionation KW - Laser ablation KW - ICP-MS PY - 2011 DO - https://doi.org/10.1016/j.sab.2011.04.005 SN - 0584-8547 SN - 0038-6987 VL - 66 IS - 6 SP - 432 EP - 438 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-24065 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Barthel, Mathias A1 - Seeger, Stefan A1 - Hahn, Oliver A1 - Wilke, Olaf A1 - Horn, Wolfgang A1 - Jann, Oliver T1 - Quantitative and qualitative characterisation of ultrafine particles emitted by laser printing devices T2 - European Aerosol Conference CY - Manchester, England DA - 2011-09-04 PY - 2011 AN - OPUS4-24404 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Barthel, Mathias A1 - Pedan, Vasilisa A1 - Hahn, Oliver A1 - Rothhardt, Monika A1 - Bresch, Harald A1 - Jann, Oliver A1 - Seeger, Stefan T1 - XRF-Analysis of fine and ultrafine particles emitted from laser printing devices N2 - In this work, the elemental composition of fine and ultrafine particles emitted by ten different laser printing devices (LPD) is examined. The particle number concentration time series was measured as well as the particle size distributions. In parallel, emitted particles were size-selectively sampled with a cascade impactor and subsequently analyzed by the means of XRF. In order to identify potential sources for the aerosol's elemental composition, materials involved in the printing process such as toner, paper, and structural components of the printer were also analyzed. While the majority of particle emissions from laser printers are known to consist of recondensated semi volatile organic compounds, elemental analysis identifies Si, S, Cl, Ca, Ti, Cr, and Fe as well as traces of Ni and Zn in different size fractions of the aerosols. These elements can mainly be assigned to contributions from toner and paper. The detection of elements that are likely to be present in inorganic compounds is in good agreement with the measurement of nonvolatile particles. Quantitative measurements of solid particles at 400 °C resulted in residues of 1.6 × 109 and 1.5 × 1010 particles per print job, representing fractions of 0.2% and 1.9% of the total number of emitted particles at room temperature. In combination with the XRF results it is concluded that solid inorganic particles contribute to LPD emissions in measurable quantities. Furthermore, for the first time Br was detected in significant concentrations in the aerosol emitted from two LPD. The analysis of several possible sources identified the plastic housings of the fuser units as main sources due to substantial Br concentrations related to brominated flame retardants. KW - Particulate emissions KW - UFP KW - FP KW - Laser printers KW - XRF PY - 2011 DO - https://doi.org/10.1021/es201590q SN - 0013-936X SN - 1520-5851 VL - 45 IS - 18 SP - 7819 EP - 7825 PB - ACS Publ. CY - Washington, DC AN - OPUS4-24393 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seefeldt, Henrik A1 - Braun, Ulrike A1 - Hofmann-Böllinghaus, Anja T1 - Influence of structure, wood content, moisture and additives on the burning behaviour of wood plastic composites T2 - Fire and Materials - 12th international conference and exhibition CY - San Francisco, CA, USA DA - 2011-01-31 PY - 2011 AN - OPUS4-23393 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hofmann-Böllinghaus, Anja A1 - Knaust, Christian A1 - Krüger, Simone A1 - Raspe, Tina A1 - Deubel, Jan T1 - Assessment of development time of a smouldering fire at a crime scene experimental and numerical investigations T2 - Fire & Materials Konferenz 2011 CY - San Francisco, CA, USA DA - 2011-01-31 PY - 2011 AN - OPUS4-23404 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dülsen, Steffen A1 - Hofmann-Böllinghaus, Anja A1 - Krause, Ulrich T1 - Untersuchung zu Brandursachen und Brandverlauf bei Busbränden N2 - Busbrände treten relativ häufig auf, auch wenn sich das im öffentlichen Bewusstsein nicht unbedingt widerspiegelt. Nach einer eigenen Internetrecherche brennt etwa an jedem zweiten Tag ein Bus in Deutschland. Die grundlegenden Brandschutzvorschriften für Busse gehen auf die amerikanische Norm FMVSS 302 zurück, die in den 60er Jahren entwickelt wurde und ist quasi weltweit noch immer in sämtlichen nationalen und internationalen Brandschutzvorschiften wiederzufinden. Ziel der FMVSS 302 ist es vor allem, Fahrzeugbrände durch das Rauchen zu verhindern. Verschiedene Untersuchungen zeigen jedoch, dass die meisten Busbrände andere Ursachen haben und zu ca. 80 % im Motorraum entstehen. Auch das Versagen von elektrischen Komponenten ist häufiger die Brandursache. Dies geschah z.B. im Jahr 2008 bei einem schweren Busbrand in der Nähe von Hannover, bei dem sich gerade einmal 13 Passagiere selber retten konnten und 20 Menschen ihr Leben verloren. Einige Brandleichen wurden sogar noch am Sicherheitsgurt angeschnallt aufgefunden. Durch die enorme Zunahme brennbarer Kunststoffteile in Bussen entstand ein bisher unberücksichtigtes Risiko, das bei der Normentwicklung in den 1960er Jahren nicht berücksichtigt wurde. So hat sich die Brandlast seitdem etwa verzehnfacht und das toxische Potential erheblich gesteigert. Nach wenigen Minuten muss bei den Brandopfern bereits mit einem schnellen Tod durch Rauchgasvergiftungen gerechnet werden. Aufgrund der schnellen Brandentwicklung in Bussen können Passagiere in den allermeisten Fällen nicht bis zum Eintreffen der Feuerwehr warten und müssen sich selber retten. Die Zeit für die Selbstrettung muss signifikant verlängert werden, so dass auch mobilitätseingeschränkte Passagiere eine Chance zum Verlassen des Busses haben. Der Vergleich mit Brandschutzanforderungen anderer Transportsektoren (Bahn, Schiff, Flugzeug) zeigt, dass die Anforderungen dort sehr viel höher sind. Sowohl die Entflammbarkeit als auch die Wärmefreisetzung sowie die Rauchfreisetzung werden in diesen Normen begrenzt. Zudem werden Materialanforderungen hinsichtlich der Rauchgastoxizität gestellt. Im Ergebnis dieser Arbeit sollen einerseits Brandschutzempfehlungen für die zweckmäßige und zugleich wirtschaftlich vertretbare Ausstattung von Bussen im Innenbereich unterbreitet werden. Andererseits sollen auch Überarbeitungsvorschläge für Prüftests vorgestellt werden, die den Brandschutz von Kraftomnibussen sicherstellen und erstmals auch Grenzwerte für die Rauchgastoxizität beinhalten. Dazu werden neben den Brandversuchen auch numerische Simulationen mit dem Fire Dynamics Simulator (FDS, Version 5, NIST) durchgeführt, in denen verschiedene Brandszenarien mit unterschiedlichen Buskategorien simuliert werden. T2 - 59. vfdb-Jahresfachtagung CY - Berlin, Deutschland DA - 2011-05-30 PY - 2011 SP - 805 EP - 816 AN - OPUS4-23847 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Rudolf T1 - Pharmazeutika im Abwasser- und Trinkwasserkreislauf T2 - GDCh Wissenschaftsforum Chemie 2011 CY - Bremen, Germany DA - 2011-09-06 PY - 2011 AN - OPUS4-24944 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Rudolf T1 - Identification of unknown contaminants and metabolites of pharmaceuticals in waste water by HR-MS analysis of chromatographic fractions pre-selected by ELISA T2 - 7th Annual LC/MS/MS Workshop on Environmental Applications and Food Safety CY - Buffalo, NY, USA DA - 2011-06-13 PY - 2011 AN - OPUS4-24942 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Rudolf A1 - Wagner, Sascha A1 - Kuhne, Maren A1 - Resch-Genger, Ute A1 - Kunte, Hans-Jörg A1 - Schenk, J. A. T1 - Murine hybridoma cells can be specifically labeled and sorted by Flow Cytometry (FACS) in order to select clones for mab production T2 - Proteomics Forum CY - Berlin, Germany DA - 2011-04-03 PY - 2011 AN - OPUS4-24950 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Rudolf A1 - Bahlmann, Arnold A1 - Carvalho, José Joao A1 - Lehmann, Andreas T1 - Non-target Analysis of Emerging Contaminants by LC-ELISA and HR-MS T2 - ICCE 2011 - EuCheMS International Conference on Chemistry and the Environment CY - Zurich, Switzerland DA - 2011-09-12 PY - 2011 AN - OPUS4-24945 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Rudolf A1 - Kuhne, Maren A1 - Wagner, Sascha A1 - Resch-Genger, Ute A1 - Kunte, Hans-Jörg A1 - Schenk, J. A. T1 - Selektion muriner Hybridomazellen am Durchflußzytometer (FACS) T2 - 5. Senftenberger Innovationsforum Multiparameteranalytik CY - Senftenberg, Germany DA - 2011-03-10 PY - 2011 AN - OPUS4-24948 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Rudolf A1 - Grandke, Julia A1 - Bahlmann, Arnold A1 - Carvalho, José Joao A1 - Bremser, Wolfram T1 - Uncertainty in Measurement with Immunoassays T2 - EURACHEM/CITAC-Workshop: Recent Development in Measurement Uncertainty CY - Lisbon, Portugal DA - 2011-06-07 PY - 2011 AN - OPUS4-24941 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grandke, Julia A1 - Schneider, Rudolf A1 - Resch-Genger, Ute T1 - Temperature Dependence of Immunoassays T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-24949 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lima, D.L.D. A1 - Silva, C.P. A1 - Schneider, Rudolf A1 - Esteves, V.I. T1 - Development of an ELISA procedure to study sorption of atrazine onto a sewage sludge-amended luvisol soil N2 - Pesticides may contaminate ground and surface waters and one of the major factors governing this property is soil sorption. Sorption can be assessed by batch equilibrium technique which produces lots of extracts with high dissolved organic carbon concentration in which the pesticide concentration has to be determined. We developed an ELISA procedure to analyse atrazine based on polyclonal antibodies (C193) for which tracer structure and dilutions of immunochemical reagents were adapted to fit the purpose. After a 1000-fold dilution (or after an SPE clean-up procedure) extracts of a sewage-sludge amended luvisol (used as an example application of the methodology developed) could be reliably analysed. The Freundlich model is able to describe adsorption for this system (r² = 0.977) delivering a distribution coefficient KF of 1.6 ± 0.2 (mg kg-1) (mg L-1)-N and an isotherm nonlinearity factor N of 0.70 ± 0.09. KW - ELISA KW - Atrazine KW - Sorption PY - 2011 DO - https://doi.org/10.1016/j.talanta.2011.06.024 SN - 0039-9140 VL - 85 IS - 3 SP - 1494 EP - 1499 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-24305 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Calisto, V. A1 - Bahlmann, Arnold A1 - Schneider, Rudolf A1 - Esteves, V.I. T1 - Application of an ELISA to the quantification of carbamazepine in ground, surface and wastewaters and validation with LC-MS/MS N2 - Carbamazepine is a psychiatric pharmaceutical widely detected in aquatic environments. Due to its generalized occurrence and environmental persistence it might be considered as an anthropogenic pollution indicator. In this research, a previously developed enzyme-linked immunosorbent assay (ELISA), based on a commercial monoclonal antibody, was applied to the quantification of carbamazepine in ground, surface and wastewaters and results were validated by liquid chromatography–tandem mass spectrometry (LC–MS/MS). The performance of the applied ELISA methodology was tested in the presence of high concentrations of sodium chloride and dissolved organic matter. The method was not significantly affected by matrix effects, being adequate for the quantification of carbamazepine in environmental samples, even without sample pre-treatment. This method allows the quantification of carbamazepine in the range of 0.03–10 µg L-1, with a relative error lower than 30%. Due to a pH dependent cross-reactivity with cetirizine, an antihistaminic drug, the assay also enabled the quantification of cetirizine in the samples. The application of the developed method to the quantification of carbamazepine was performed by using environmental samples with very different matrices, collected in the geographical area of Ria de Aveiro, an estuarine system located in the North of Portugal. Carbamazepine was detected in all analyzed wastewater samples and in one surface water with concentrations between 0.1 and 0.7 µg L-1. Validation with LC–MS/MS revealed that results obtained by ELISA are 2–28% overestimated, which was considered highly satisfactory due to the absence of sample pre-treatments. KW - Immunoassay KW - Pharmaceuticals KW - Environment KW - Wastewater treatment plants KW - Matrix effects KW - Cetirizine PY - 2011 DO - https://doi.org/10.1016/j.chemosphere.2011.04.072 SN - 0045-6535 SN - 0366-7111 VL - 84 IS - 11 SP - 1708 EP - 1715 PB - Elsevier Science CY - Kidlington, Oxford AN - OPUS4-24306 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ulanova, T. A1 - Tuma, Dirk A1 - Maurer, G. T1 - Phase equilibria and partitioning of L-histidine and three pharmaceuticals to pH-adjusted high-pressure liquid phases of the ternary system (ethene + water + 2-propanol) N2 - Adding some salt to a homogeneous aqueous liquid solution of an organic solvent often results in a liquid–liquid phase split. However, such a phase split can also be achieved by charging such a liquid with a gas, in particular when the temperature is close to the critical temperature of that specific gas. This phenomenon is called 'salting out by a near-critical gas'. It might be applied in a high-pressure extraction process, for example, to separate and recover valuable biomolecules from aqueous phases. Using a neutral gas like, for example, ethene for pressurizing additionally allows to adjust the pH of the coexisting liquid phases and to influence the partitioning of biomolecules when they change their electric net charge with the pH of the solution. The design of such separation processes requires not only reliable information on the phase forming system, that is, the ternary system (near-critical gas + water + organic solvent), but also on the partitioning of typical solutes to the coexisting phases. The present publication reports data (from an experimental study with a static-analytical device) for the partitioning of four biomolecules, that is, L-histidine, Aspirin, cimetidine, and 4-dimethylaminoantipyrine (at nearly infinite dilution) to coexisting liquid phases of the high-pressure three-phase liquid–liquid–vapor (L1L2V) equilibrium of the ternary system (ethene + water + 2-propanol) at (293 and 333) K and pressures from about (5.5 to 17) MPa. The coexisting liquid phases are characterized by distinctly different compositions, the aqueous phase being more hydrophilic than the alkanol-rich phase. Moreover, electrolytes were additionally added to adjust the pH conditions in the liquid phases. The pH-dependent dissociation equilibrium and the related net charge of the biomolecules primarily determine the partitioning behavior: The pH effect is stronger than the impact of varying pressure or temperature. For example, a switch from basic to acidic conditions can invert the partitioning, if that switch at the same time effects a change in the net charge of the solute, for example, from an ionic to a neutral molecule (or vice versa). The ionic solute is more hydrophilic (and thus prefers the aqueous phase), whereas the neutral or zwitterionic solute is less hydrophilic (i.e., more lipophilic) and consequently prefers the propanol-rich liquid phase. KW - Wirkstoffe KW - Bioverfahrenstechnik KW - Extraktion KW - Mischphasenthermodynamik PY - 2011 DO - https://doi.org/10.1021/je2001914 SN - 0021-9568 VL - 56 IS - 12 SP - 4376 EP - 4391 PB - Soc. CY - Washington, DC, USA AN - OPUS4-25899 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tuma, Dirk A1 - Chobanov, K. A1 - Kumelan, J. A1 - Maurer, G. T1 - Gaslöslichkeiten und Hochdruckphasengleichgewichte in ternären Systemen mit Beteiligung ionischer Flüssigkeiten T2 - Thermodynamik-Kolloquium der DECHEMA e.V. CY - Frankfurt am Main, Germany DA - 2011-10-04 PY - 2011 AN - OPUS4-29340 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bremser, Wolfgang A1 - Tuma, Dirk A1 - Heine, H.-J. T1 - International reference values for calibration of process gas chromatographs (PGCs) and related uncertainties N2 - In a mutual framework agreement, the two German national institutes BAM (Federal Institute of Materials Research and Testing) and PTB (Physikalisch-Technische Bundesanstalt) agreed upon the development, provision, and dissemination of national measurement standards for chemical analysis via primary reference measuring systems. Traceability to national standards and international comparability is of key importance for the acceptance of measurement results in metrology. T2 - 6th International Gas Analysis Symposium & Exhibition -- GAS 2011 CY - Rotterdam, The Netherlands DA - 09.02.2011 KW - Metrology KW - Gas standards KW - Certification PY - 2011 AN - OPUS4-35943 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tuma, Dirk A1 - Maurer, G. A1 - Chobanov, K. A1 - Ulanova, T. T1 - Neue Untersuchungen zum Phänomen "Aussalzen mit einem nahekritischen Gas" T2 - Jahrestreffen des Fachausschusses Hochdruckverfahrenstechnik der DECHEMA e. V. CY - Maribor, Slovenia DA - 2011-03-10 PY - 2011 AN - OPUS4-26706 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubowski, Norbert A1 - Panne, Ulrich A1 - Weller, Michael G. A1 - Giesen, Charlotte A1 - Müller, Larissa A1 - Roos, P.H. T1 - Measurement and detection of labelled antibodies: New applications in oncology an pathology T2 - AbCAP, Projekt Meeting BMBF CY - Berlin, Germany DA - 2011-03-31 PY - 2011 N1 - Geburtsname von Müller, Larissa: Wäntig, L. - Birth name of Müller, Larissa: Wäntig, L. AN - OPUS4-23808 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubowski, Norbert A1 - Chinthalapati, Siva Kesava Raju A1 - Lindner, Uwe A1 - Lingott, Jana A1 - Panne, Ulrich T1 - Speciation von Gd-haltigen MRI Kontrastmitteln in Berliner Flüssen und Seen T2 - GDCh-Wissensschaftsforum Chemie 2011 CY - Bremen, Germany DA - 2011-09-05 PY - 2011 AN - OPUS4-25364 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubowski, Norbert A1 - Panne, Ulrich A1 - Weller, Michael G. A1 - Giesen, Charlotte A1 - Müller, Larissa T1 - Bioimaging: Measurement and detection of labelled antibodies: New applications in toxicology, oncology and pathology T2 - CCQM 2011 CY - Paris, France DA - 2011-04-12 PY - 2011 N1 - Geburtsname von Müller, Larissa: Wäntig, L. - Birth name of Müller, Larissa: Wäntig, L. AN - OPUS4-25363 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kovalev, Alexander A1 - Sturm, Heinz T1 - Observation of nanoscale hot-spot generation on a 2, 4, 6-trinitrophenol (TNP) single crystal N2 - An energetic material (EM) creates a local thermal point when it accepts energy and the EM will explode due to thermal decomposition when the hot-spot temperature reaches the explosive temperature. The initial stage of the hot-spot formation on 2, 4, 6-trinitrophenol (TNP) single crystal has been observed at the nanometer scale using atomic force microscopy (AFM). The hot-spot generation has been directly initiated by means of an AFM tip. The phenomenon is accompanied by producing agglomerated spherical-like nanoparticles due to a low-temperature decomposition of TNP. It has been observed that the agglomerated particles are produced outside of the stimulated region. The observed decomposition process at the nanoscale doesn't lead to a self-sustaining shock as detonation or explosion. The results are of interest in relation to explore the origin of deformation-induced chemical decomposition or detonation of EM. KW - Energetic material KW - Hot-spot KW - Atomic force microscopy KW - Scratching KW - Dynamic ploughing lithography KW - Nanomanipulation KW - 2, 4, 6-trinitrophenol PY - 2011 DO - https://doi.org/10.1016/j.susc.2011.06.012 SN - 0039-6028 VL - 605 IS - 17-18 SP - 1747 EP - 1753 PB - Elsevier CY - Amsterdam AN - OPUS4-24367 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schäffer, A. A1 - Sturm, Heinz A1 - Wachtendorf, Volker A1 - Plitzko, S. A1 - Ragot, J. A1 - Kuhlbusch, T. A1 - Voetz, M. T1 - CarboLifeCycle - CNT-Materials: Properties, Release, Fate and Effects in the Environment T2 - Inno. CNT Jahrestagung CY - Ettlingen, Germany DA - 2011-01-25 PY - 2011 AN - OPUS4-23096 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sturm, Heinz A1 - Tavares, Luciana A1 - Kjelstrup-Hansen, J. A1 - Rubhahn, H.-G. T1 - Bilayer polymer/oxide coating for electroluminescent organic semiconductors T2 - E-MRS 2011 Spring Meeting; IUMRS ICAM 20011 & E-MRS / MRS Bilateral Conference on Energy CY - Nice, France DA - 2011-05-09 PY - 2011 AN - OPUS4-23667 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meyer-Plath, Asmus A1 - Sturm, Heinz A1 - Wachtendorf, Volker A1 - Plitzko, S. A1 - Ragot, J. A1 - Kuhlbusch, T. A1 - Voetz, M. A1 - Schäffer, A. T1 - CarboLifeCycle - CNT Materials: Properties, Release, Fate and Effects in the Environment T2 - Inno. CNT Jahrestagung CY - Ettlingen, Germany DA - 2011-01-25 PY - 2011 AN - OPUS4-23095 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sturm, Heinz A1 - Schröter, Maria-Astrid A1 - Weimann, Christiane T1 - Nanotribology and vibrating contacts T2 - Chinese-German Symposium Nanomanufacturing and Nanotribology CY - Berlin, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23582 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröter, Maria-Astrid A1 - Weimann, Christiane A1 - Sturm, Heinz A1 - Holschneider, M. T1 - Towards a simplified mechanical model of insect wings T2 - Microscopy Conference CY - Kiel, Germany DA - 2011-08-28 PY - 2011 AN - OPUS4-23581 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kovalev, Alexander A1 - Sturm, Heinz T1 - Nanoscale hotspot formation in an energetic material during friction T2 - Jahrestagung der Deutschen Physikalischen Gesellschaft CY - Dresden, Germany DA - 2011-03-13 PY - 2011 AN - OPUS4-23595 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tuma, Dirk T1 - Measurement protocols for general applications in gas analysis T2 - GAS 2011 CY - Rotterdam, Netherlands DA - 2011-02-09 PY - 2011 AN - OPUS4-23221 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tuma, Dirk A1 - Brown, A. S. A1 - Jones, D. N. A1 - Milton, M. J. T. A1 - Downey, M.L. A1 - v. Vargha, G. A1 - van der Veen, A.M.H. A1 - Ent, H. A1 - Arrhenius, K. T1 - Towards a European Infrastructure for the Characterisation of Energy Gases T2 - 2nd IMEKO TC 11 International Symposium Metrological Infrastructure CY - Cavtat, Croatia DA - 2011-06-15 PY - 2011 AN - OPUS4-24304 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Sturm, Heinz A1 - Meyer-Plath, Asmus T1 - CarbonLifeCycle - Weathering Induced Degradation of Nanoparticle-Functionalised Polymers T2 - 5th European Weathering Symposium (EWS) CY - Lisbon, Portugal DA - 2011-09-21 PY - 2011 AN - OPUS4-24424 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröter, Maria-Astrid A1 - Weimann, Christiane A1 - Sturm, Heinz A1 - Holschneider, M. T1 - Towards a deeper understanding of the dynamic properties of cantilever probes T2 - 37. Int. Conf. Micro and Nano Engineering CY - Berlin, Germany DA - 2011-09-19 PY - 2011 AN - OPUS4-23866 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Siegel, David T1 - Chemical Solutions to Current Issues in the Instrumental Quantification of Food Mycotoxins N2 - Mycotoxins are toxic secondary metabolites of ubiquitously occurring moulds. Through the consumption of contaminated foods, they can cause acute or chronic intoxications in humans. Here, it is demonstrated how covalent hydrazine chemistry can be used to improve the performance of instrumental methods for the quantification of trace level food mycotoxins. In the case of the Alternaria mycotoxin tenuazonic acid, pre-column derivatisation with 2,4-dinitrophenylhydrazine resolved chromatographic issues due to the chemical properties of the analyte and allowed for its rapid, sensitive and selective quantification in cereals and beer by high performance liquid chromatography- ion-trap two stage mass spectrometry (HPLC-IT-MS2). Tenuazonic acid could be detected for the first time in beer and buckwheat flour. Although the encountered levels were too low to cause acute intoxications, the frequency of contamination indicated possible health risks due to chronic exposure. In a second scenario, dynamic covalent hydrazine chemistry (DCHC) was exploited for a novel extraction and cleanup method applicable to the Fusarium mycotoxin zearalenone occurring in edible oils. Zearalenone was extracted by hydrazone formation on a hydrazinefunctionalised polymer resin and subsequently released hydrolytically for quantification by HPLC-fluorescence detection (HPLC- FLD). The high selectivity of the approach allowed for the omission of MS detection and immunoaffinity cleanup. The DCHC method was superior to previously published methods in terms of handling efforts, cost, precision and selectivity and is well suited for the monitoring of the current European maximum level for zearalenone in refined maize oil. In the second part of the dissertation, possible degradation routes of Alternaria mycotoxins upon storage and bread baking are discussed. In the frame of a kinetic study, it was shown that tenuazonic acid is degraded by two parallel processes, deacetylation and epimerisation, when stored in aqueous solution (half-life at 25 °C ~ 74 days). The primary degradation product deacetyl tenuazonic acid was less stable than its parent compound and degraded rapidly in beverage matrices. In model baking experiments it was furthermore revealed that alternariol, alternariol monomethyl ether and altenuene are stable under typical baking conditions. A newly identified degradation route, which is based on a sequence of hydrolysis and decarboxylation, caused only minor substance losses (< 1 %). Still, the degradation products could be detected in commercial rusk and crispbread by HPLC-tandem mass spectrometry (HPLC-MS/MS). N2 - Mykotoxine sind sekundäre Stoffwechselprodukte ubiquitärer Schimmelpilze. Über den Konsum belasteter Nahrungsmittel können sie beim Menschen, je nach Art und Ausmaß der Exposition, akute bzw. chronische Vergiftungen hervorrufen. Ziel der Arbeiten war es, durch chemische Methoden zwei Probleme aus dem Bereich der quantitativen Mykotoxinanalytik zu lösen. Hierbei ging es erstens um die Inkompatibilität des Alternaria Mykotoxins Tenuazonsäure mit üblichen Hochleistungsflüssigkeitschromatographie (HPLC) Säulen und zweitens um die selektive analytische Extraktion des in der Europäischen Union regulierten Fusarium Mykotoxins Zearalenon aus Speiseölen. Für beide Problemstellungen wurden Lösungen erarbeitet, die auf dem Einsatz kovalenter Hydrazinchemie im Rahmen der Probenvorbereitung beruhen. Die Verfahren wurden validiert und auf Verbraucherprodukte angewendet. Die Bestimmung der Tenuazonsäure erfolgte dabei nach Derivatisierung mit 2,4-Dinitrophenylhydrazin mittels HPLC-Ion-trap Massenspektrometrie (HPLC-IT-MS2). Für Zearalenon wurde eine neuartige Festphasenextraktionsmethode basierend auf dynamischer kovalenter Hydrazinchemie (DCHC) entwickelt und in Verbindung mit HPLC-Fluoreszenzdetektion (HPLC-FLD) eingesetzt. Beide Ansätze zeichnen sich durch hohe Selektivität, einfaches Handling und einen geringen Lösungsmittelverbrauch aus; alle Reaktionen erfolgen bei Raumtemperatur. So konnte Tenuazonsäure erstmals in Getränken (Bier) und Buchweizenmehl nachgewiesen werden. Der zweite Teil der Arbeit beschäftigt sich mit möglichen Abbaureaktionen der Alternaria Mykotoxine bei der Lagerung und Zubereitung von Lebensmitteln. Im Rahmen einer kinetischen Studie wurde gezeigt, dass Tenuazonsäure in wässriger Lösung über zwei parallele Prozesse, hydrolytische Deacetylierung und Epimerisierung, abgebaut wird (Halbwertszeit bei 25 °C ~ 74 Tage). Während das vornehmlich gebildete Produkt, Deacetyl-Tenuazonsäure, in wässriger Lösung stabil war, wurde es in Getränkematrices innerhalb weniger Tage abgebaut. In Modell-Backversuchen wurde weiterhin die Stabilität der Dibenzo- -pyron Derivate Alternariol, Alternariol-monomethylether und Altenuen untersucht. Unter typischen Backbedingungen erwiesen sich die Verbindungen als stabil. Ein erstmals belegter Abbaumechanismus für Alternariol und Alternariol-monomethylether, der auf einer Sequenz aus Hydrolyse und Decarboxylierung beruht, führte nur zu geringen Substanzverlusten (< 1 %). Dennoch konnten die Abbauprodukte mittels HPLC-Tandem-Massenspektrometrie (HPLCMS/MS) in extrudierten Produkten (Knäckebrot und Zwieback) nachgewiesen werden. T3 - BAM Dissertationsreihe - 71 KW - Alternaria KW - Mass spectrometry KW - Liquid chromatography KW - Quantification KW - Zearalenone PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-876 SN - 978-3-9813853-8-0 SN - 1613-4249 VL - 71 SP - 1 EP - 126 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-87 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Matschulat, Andrea Isabel T1 - Entwicklung neuer Sonden für bioanalytische Anwendungen der oberflächenverstärkten Raman-Streuung N2 - Surface-enhanced Raman scattering (SERS) has been established as a versatile tool for probing and labeling in analytical applications, based on the vibrational spectra of samples as well as label molecules in the proximity of noble metal nanostructures. The aim of this work was the construction of novel SERS hybrid probes. The hybrid probes consisted of Au and Ag nanoparticles and reporter molecules, as well as a targeting unit. The concept for the SERS hybrid probe design was followed by experiments comprising characterization techniques such as UV/Vis- spectroscopy (UV/Vis), Transmission electron microscopy (TEM) and Dynamic Light Scattering (DLS), respectively. SERS experiments were per- formed for studying and optimizing the plasmonic properties of nanoparticles with respect to their enhancement capabilities. The SERS-probes had to meet following requirements: biocompatibility, stability in physiological media, and enhancement of Raman-signals from Raman reporter molecules enabling the identification of different probes even in a complex biological environment. Au and Ag nanoaggregates were found to be the most appropriate SERS substrates for the hybrid probe design. The utilization of Raman reporters enabled the identification of different SERS probes in multiplexing experiments. In particular, the multiplexing capability of ten various reporter molecules para-aminobenzenethiol, 2-naphthalenethiol, crystal violet, rhodamine (B) isothiocyanate, fiuorescein isothiocyanate, 5,5'dithiobis(2-nitrobenzoic acid), para- mercaptobenzoic acid, acridine orange, safranine O und nile blue was studied using NIR-SERS excitation. As demonstrated by the results the reporters could be identified through their specific Raman signature even in the case of high structural similarity. Chemical separation analysis of the reporter signatures was performed in a trivariate approach, enabling the discrimination through an automated calculation of specific band ratios. The trivariate identification could be a promising method for SERS-multiplexing in analytical applications. Multivariate methods such as Principal Components Analysis (PCA) and Hierarchical Cluster Analysis (HCA) were as well applied for discrimination and imaging of the reporter signatures. With the help of multivariate imaging methods based on cluster analysis, it could be for the first time demonstrated that such methods provided a fast identification of various SERS hybrid probes inside the biological matrix, this was demonstrated using living 3T3 cells. Further, in a duplex imaging approach, the probes fulfill the requirements for the sensitive detection of both the specific reporter signatures and intrinsic information coming from eukaryotic cells. The results of cluster methods and principal components approaches for discrimination indicate that fast, multivariate evaluation of whole sets of multiple probes is feasible, beyond the visual inspection of individual spectra that has been practiced so far. This suggests multiplexing applications with SERS hybrid nanoprobes and SERS tags in very high density sensing and biological imaging applications, where fast read-out is required. The pH-sensitivity of SERS-Tags that consisted of different reporter molecules attached to aggregated Au and Ag nanoparticles in the range between pH∼3-10 was studied. It could be demonstrated that the reporter molecules provided pH-dependent SERS signatures and could therefore be suitable for the sensitive pH-detection, e.g., inside cellular compartments. The construction of targeted SERS probes was based on the integration of a goat-anti- mouse antibody as targeting element Antibodies were coupled to Au and Ag nanoprobes surrounded by a Bovine Serum Albumin (BSA) coating which served as a carrier for the covalent linkage of a Raman reporter molecule and the targeting units at the same time In experiments with BSA and a conjugated reporter the spectra of the BSA-coupled re- porters provided an indication of the secondary structure of BSA which is related to the BSA-reporter coupling procedure In in v i t ro -experiments with BSA-coupled nanoprobes inside 3T3 cells reporter signatures and intrinsic information from the cellular matrix could be delivered BSA enabled the coupling of reporter molecules as well as the targeting of antibodies and served as stabilizer of the gold nanoaggregates The functionality of the coupled antibodies after their integration into the SERS probe was retained This was verified by the results of a direct Enzyme-Linked Immunosorbent Assay (ELISA) Conjugates with implemented reporter molecules could be characterized using SERS The application of the complete probes suggested a use of these novel biocompatible stable and targeted SERS probes that can be excited out-of- resonance also for other bioanalytical applications. On the basis of the constructed SERS hybrid probes comprising a large number of BSA- coupled reporters could e g be implemented for automated high-througput immuno- assays where they are arranged on a microstructured device for the simultaneous and multilevel SERS-readout in one step . T3 - BAM Dissertationsreihe - 78 KW - Au und Ag Nanopartikel KW - SERS-Multiplexing KW - Raman Reporter KW - Multivariate Datenanalyse KW - intrazelluläre Hybridsonden PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-802 SN - 978-3-9814281-8-6 SN - 1613-4249 VL - 78 SP - 1 EP - 192 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-80 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Balski, Matthias A1 - Meyer, S. A1 - Kipphardt, Heinrich A1 - Jakubowski, Norbert A1 - Panne, Ulrich T1 - Determination of trace impurities in solar grade silicon T2 - European Winter Conference on Plasma Spectrochemistry CY - Zaragoza, Spain DA - 2011-01-30 PY - 2011 AN - OPUS4-23225 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Panne, Ulrich T1 - Hyphenated Techniques for New Insights in Polymer Analysis: 2dim LC and MALDI T2 - 4. Workshop Möglichkeiten und Grenzen der HPLC in den Lebenswissenschaften CY - Dresden, Germany DA - 2011-03-30 PY - 2011 AN - OPUS4-23460 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Balski, Matthias A1 - Kühn, Andreas A1 - Meyer, S. A1 - Kipphardt, Heinrich A1 - Jakubowski, Norbert A1 - Panne, Ulrich T1 - Elementspurenanalytik in Solarsilicium T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23825 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Merk, Sven A1 - Höhse, Marek A1 - Gornushkin, Igor B. A1 - Maiwald, Michael A1 - Panne, Ulrich T1 - Laser Induced Breakdown and Raman Spectroscopy with Diode Pumped Solid State Lasers T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23740 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Balski, Matthias A1 - Meyer, S. A1 - Kipphardt, Heinrich A1 - Jakubowski, Norbert A1 - Panne, Ulrich T1 - Determination of trace impurities in solar grade silicon T2 - CANAS 2011 CY - Leipzig, Germany DA - 2011-03-13 PY - 2011 AN - OPUS4-23235 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar A1 - Panne, Ulrich A1 - Meng, Birgit A1 - Emmerling, Franziska A1 - Müller, Urs T1 - Investigations of cement phase assemblage by spyce-and time-resolved X-Ray diffraction T2 - International Congress on the Chemistry of Cement (ICCC 2011) CY - Madrid, Spain DA - 2011-07-03 PY - 2011 AN - OPUS4-21094 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar A1 - Panne, Ulrich A1 - Emmerling, Franziska A1 - Meng, Birgit A1 - Müller, Urs T1 - Investigations of cement phase assemblage by space- and time-resolved X-Ray diffraction T2 - International Congress on the Chemistry of Cement (ICCC 2011) CY - Madrid, Spain DA - 2011-07-03 PY - 2011 AN - OPUS4-21206 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar A1 - Emmerling, Franziska A1 - Müller, Urs A1 - Panne, Ulrich A1 - Meng, Birgit T1 - Analysis of cementitious materials by X-Ray diffraction methods -Time and spatial resolved T2 - 13th International Congress on the Chemistry of Cement (ICCC) CY - Madrid, Spain DA - 2011-07-03 PY - 2011 AN - OPUS4-22568 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppen, Robert A1 - Koch, Matthias A1 - Klein-Hartwig, Karin A1 - Nehls, Irene A1 - Panne, Ulrich T1 - Natürliche Umwelt- und Lebensmitteltoxine: Entwicklung eines Referenzmateirals für die Mykotoxine T-2 und HT-2 T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-22245 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rackwitz, Vanessa A1 - Ostermann, Markus A1 - Panne, Ulrich A1 - Hodoroaba, Vasile-Dan T1 - Limits of Detection of µ-XRF with SEM for RoHS relevant Elements T2 - European Microbeam Analysis Society EMAS 2011 CY - Angers, France DA - 2011-05-15 PY - 2011 AN - OPUS4-22503 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rackwitz, Vanessa A1 - Panne, Ulrich A1 - Hodoroaba, Vasile-Dan T1 - An Attempt of µ-XRF Analysis by Exploiting the Rayleigh-to-Compton Intensity Ratio T2 - European Microbeam Analysis Society EMAS 2011 CY - Angers, France DA - 2011-05-15 PY - 2011 AN - OPUS4-22504 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Giesen, Charlotte A1 - Panne, Ulrich A1 - Weller, Michael G. A1 - Jakubowski, Norbert A1 - Mairinger, T. T1 - Immunohistochemistry with lanthanide labeled primary antibodies detected by LA-ICP-MS T2 - Winter Plasma Conference 2010 CY - Zaragoza, Spain DA - 2011-01-30 PY - 2011 AN - OPUS4-22584 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wienold, Julia A1 - Börno, Fabian A1 - Traub, Heike A1 - Jakubowski, Norbert A1 - Panne, Ulrich T1 - Lithiumboratschmelzaufschlüsse für die Spurenelementanalyse von refraktären Materialien mit Laser Ablation ICP-MS T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23226 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lischka, Susanne A1 - Nehls, Irene A1 - Panne, Ulrich A1 - Piechotta, Christian T1 - Synthese 13C-markierter Kalibrierstandards für die Arsenspeziesanalytik mittels LC-ESI-MS/MS T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23369 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar A1 - Emmerling, Franziska A1 - Müller, Urs A1 - Panne, Ulrich T1 - High resolution investigations of cementitious materials by Synchrotron radiation based X-ray diffraction T2 - Jahrestagung der deutschen mineranologischen Gesellschaft (DMG) und Deutsche Gesellschaft für Kristallographie (DGK) CY - Salzburg, Austria DA - 2011-09-20 PY - 2011 AN - OPUS4-23741 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar A1 - Emmerling, Franziska A1 - Müller, Urs A1 - Panne, Ulrich T1 - Early crystallization processes and high resolution phase analysis of cementitious materials T2 - The Power of Powder Diffraction (Workshop) CY - Erice, Italy DA - 2011-06-02 PY - 2011 AN - OPUS4-23735 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar A1 - Emmerling, Franziska A1 - Müller, Urs A1 - Panne, Ulrich T1 - In situ investigations of cementitious material by high resolution X-ray diffraction T2 - Doktorandenseminar der GDCh CY - Attendorn, Germany DA - 2011-02-27 PY - 2011 AN - OPUS4-23609 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Merkel, Stefan A1 - Köppen, Robert A1 - Koch, Matthias A1 - Nehls, Irene A1 - Panne, Ulrich T1 - Analysenverfahren zur epimierungsfreien Analytik von Ergotalkaloiden T2 - Berliner Chemie Symposium (Jungchemikerforum) der Humboldt-Universität Berlin CY - Berlin, Germany DA - 2011-04-07 PY - 2011 AN - OPUS4-23505 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schenk, Jonas A1 - Panne, Ulrich A1 - Buurman, Merwe A1 - Kneipp, Janina A1 - Emmerling, Franziska T1 - Simultaneous Surface Enhanced Raman Scattering and UV/Vis Spectroscopy on Levitated Silver Nanoparticles T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 N1 - Geburtsname von Buurman, Merwe: Albrecht, M. - Birth name of Buurman, Merwe: Albrecht, M. AN - OPUS4-23453 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mönch, Bettina A1 - Gebert, Antje A1 - Becker, Roland A1 - Nehls, Irene A1 - Panne, Ulrich T1 - Systematische Untersuchungen zur Reinigung und Anreicherung von wässrigen Extrakten zur Analytik von Ethylglucuronid aus Haaren T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23370 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühn, Andreas A1 - Ferber, Heiko A1 - Ostermann, Markus A1 - Maiwald, Michael A1 - Panne, Ulrich T1 - Kontamination von Totalreflektios-Röntgen-Fluoreszenz-Proben im Kaltplasmaverascher T2 - Anakon 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23399 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Merkel, Stefan A1 - Köppen, Robert A1 - Koch, Matthias A1 - Nehls, Irene A1 - Panne, Ulrich T1 - Epimerisierungsfreie Analytik von Ergotalkalkaloiden T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23371 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zhu, Shengchao A1 - Weller, Michael G. A1 - Panne, Ulrich A1 - Rurack, Knut T1 - Assessment of the density of surface functional groups by three independent analytical methods: The case of carboxylate-expressing polystyrene microparticles T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-23 PY - 2011 AN - OPUS4-23933 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubowski, Norbert A1 - Panne, Ulrich A1 - Weller, Michael G. A1 - Giesen, Charlotte A1 - Müller, Larissa A1 - Roos, P. H. T1 - Measurement and detection of labelled antibodies: New applicacations in oncology and pathology T2 - AbCAP, Projekt Meeting BMBF CY - Berlin, Germany DA - 2011-03-31 PY - 2011 N1 - Geburtsname von Müller, Larissa: Wäntig, L. - Birth name of Müller, Larissa: Wäntig, L. AN - OPUS4-24696 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kadenkin, Alexander A1 - Bierstedt, Andreas A1 - Panne, Ulrich A1 - Riedel, Jens A1 - Gornushkin, Igor B. A1 - Florek, S. A1 - Geisler, S. T1 - Laser induced breakdown spectroscopy with the use of fast diode pumped solid state laser T2 - EUROANALYSIS 16 CY - Belgrade, Serbia DA - 2011-09-11 PY - 2011 AN - OPUS4-24632 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rackwitz, Vanessa A1 - Ostermann, Markus A1 - Panne, Ulrich A1 - Hodoroaba, Vasile-Dan T1 - Limits of Detection of µ-XRF with SEM/EDS for RoHS relevant elements T2 - PRORA 2011 Fachtagung Prozessnahe Röntgenanalytik CY - Berlin, Germany DA - 2011-11-24 PY - 2011 AN - OPUS4-24792 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann, Andreas A1 - Bahlmann, Arnold A1 - Weller, Michael G. A1 - Panne, Ulrich A1 - Schneider, Rudolf T1 - Determination of Carbamazepine, Sulfmaethoxazole and Cocaine in Surface Water in Berlin by LC-MS/MS and ELISA T2 - HPLS Tagung CY - Budapest, Hungary DA - 2011-06-19 PY - 2011 AN - OPUS4-24525 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Winkler, Rajko A1 - Linscheid, M. A1 - Jakubowski, Norbert A1 - Panne, Ulrich T1 - ESI-MS analysis of an un-digested IgG antibody T2 - 44. Jahrestagung der Deutschen Gesellschaft für Massenspektrometrie CY - Dortmund, Germany DA - 2011-02-27 PY - 2011 AN - OPUS4-23822 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hecht, Mandy A1 - Rurack, Knut A1 - Weller, Michael G. A1 - Panne, Ulrich T1 - Preparation and characterization of dye-doped silica nanoparticles for the red spectral region T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-23932 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Demidov, Alexandr A1 - Merk, Sven A1 - Panne, Ulrich A1 - Shabanov, Sergej V. T1 - Tomography of Laser Induced Plasma Using Abel and Radon Reconstruction Techniques T2 - EMSLIBS 2011 CY - Izmir, Turkey DA - 2011-09-11 PY - 2011 AN - OPUS4-23998 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar A1 - Sarfraz, Adnan A1 - Panne, Ulrich A1 - Emmerling, Franziska A1 - Müller, Urs T1 - Early Stages of Cement Hydration - An In-Situ Study Utilizing High resolution SyXRD T2 - Jahrestagung der Deutschen Gesellschaft für Kristallographie (DGK) CY - Munich, Germany DA - 2011-05-12 PY - 2011 AN - OPUS4-24992 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar A1 - Müller, Urs A1 - Panne, Ulrich A1 - Emmerling, Franziska A1 - Meng, Birgit T1 - Neue Wege in der Zementanalytik-Hochaufgelöste in-situ Sy-XRD T2 - 52. DAfStb- Forschungskolloquium, BAM CY - Berlin, Germany DA - 2011-11-07 PY - 2011 AN - OPUS4-25132 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Giesen, Charlotte A1 - Mairinger, T. A1 - Panne, Ulrich A1 - Weller, Michael G. A1 - Jakubowski, Norbert T1 - Immunohistochemistry with tanthanide labeled primary antibodies detected by LA-ICP-MS T2 - Winter Plasma Conference Zaragoza CY - Zaragoza, Spain DA - 2011-01-30 PY - 2011 AN - OPUS4-25165 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Höhse, Marek A1 - Gornushkin, Igor B. A1 - Merk, Sven A1 - Panne, Ulrich T1 - Laser induzierte Plasma Spektroskopie mit diodengepumpten Festkörper-Lasern T2 - Berliner Chemie Symposium CY - Berlin, Germany DA - 2011-04-07 PY - 2011 AN - OPUS4-24882 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubowski, Norbert A1 - Panne, Ulrich A1 - Weller, Michael G. A1 - Giesen, Charlotte A1 - Müller, Larissa T1 - Development of laser-ablation-ICP-MS based immunoassays T2 - Projektbesprechung Prof. Schlüter, Universitätsklinikum Hamburg-Eppendorf CY - Hamburg, Germany DA - 2011-03-23 PY - 2011 N1 - Geburtsname von Müller, Larissa: Wäntig, L. - Birth name of Müller, Larissa: Wäntig, L. AN - OPUS4-25362 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubowski, Norbert A1 - Panne, Ulrich A1 - Weller, Michael G. A1 - Giesen, Charlotte A1 - Müller, Larissa T1 - Development of laser-ablation-ICP-MS based immunoassays T2 - European Winter Conference on Plasma Spectrochemistry CY - Zaragoza, Spain DA - 2011-01-30 PY - 2011 N1 - Geburtsname von Müller, Larissa: Wäntig, L. - Birth name of Müller, Larissa: Wäntig, L. AN - OPUS4-25372 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubowski, Norbert A1 - Chinthalapati, Siva Kesava Raju A1 - Lindner, Uwe A1 - Lingott, Jana A1 - Panne, Ulrich T1 - Speciation of Gd-Based MRI Contrast Agents in Environmental Water Samples T2 - FACSS 2011 CY - Reno, NV, USA DA - 2011-10-02 PY - 2011 AN - OPUS4-25365 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Giesen, Charlotte A1 - Mairinger, T. A1 - Panne, Ulrich A1 - Weller, Michael G. A1 - Jakubowski, Norbert T1 - Histopathological studies performed by LA-ICP-MS T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-25166 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kumelan, J. A1 - Kamps, A.P.-S. A1 - Tuma, Dirk A1 - Maurer, G. T1 - Solubility of carbon dioxide in liquid mixtures of water + [bmim][CH3SO4] N2 - Experimental results are reported for the solubility of carbon dioxide in liquid mixtures of water and the ionic liquid 1-n-butyl-3-methylimidazolium methylsulfate ([bmim][CH3SO4]). Three (gas-free) solvent compositions were considered with mass fractions of [bmim][CH3SO4] of w' ≈ 0.15, 0.50, and 0.87 (mole fractions x' ≈ 0.013, 0.066, and 0.33). In the isothermal experimental series, the temperature was about (293, 333, and 373) K. The total pressure ranged up to about 10 MPa. The molality of carbon dioxide in the solvent mixture of (water + [bmim][CH3SO4]) (the mole fraction of carbon dioxide in the liquid) ranged up to approximately 1.64 mol·kg–1 (about 0.0332). The experimental results are used to determine Henry's constant of carbon dioxide in the liquid mixtures of (water + [bmim][CH3SO4]) as well as the partial molar volume of that gas at infinite dilution in those solvent mixtures. The phase equilibrium is described by applying an extension (to solvent mixtures) of Pitzer's molality scale-based equation for the Gibbs excess energy. KW - Gaslöslichkeit KW - Ionische Flüssigkeit KW - Mischphasenthermodynamik PY - 2011 DO - https://doi.org/10.1021/je200477s SN - 0021-9568 VL - 56 IS - 12 SP - 4505 EP - 4515 PB - Soc. CY - Washington, DC, USA AN - OPUS4-25898 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pham, Q.L. A1 - Haldorai, Y. A1 - Nguyen, V.H. A1 - Tuma, Dirk A1 - Shim, J.-J. T1 - Facile synthesis of poly(p-phenylenediamine)/MWCNT nanocomposites and characterization for investigation of structural effects of carbon nanotubes N2 - Poly(p-phenylenediamine) (PpPD)/carboxylic acid-functionalized multiwalled carbon nanotubes (c-MWCNTs) nanocomposites were prepared by chemical oxidative polymerization using potassium persulfate (K2S2O8) as an oxidant. Field-emission scanning electron microscopy (FE–SEM) and field-emission Transmission electron microscopy (FE–TEM) showed that a tubular layer of PpPD was coated on the surface of carbon nanotubes with a thickness of 10–20 nm. FT–IR analysis provided an evidence for the formation of nanocomposites. The thermal stability of nanocomposites was improved by addition of c-MWCNTs as confirmed by thermogravimetric analysis (TGA). XRD spectra showed that the crystalline nature of PpPD was not affected much by the addition of c-MWCNTs. As the content of c-MWCNTs was increased, the electrical conductivity of the nanocomposites increased due to the interaction between polymer and nanotubes that enhances electron delocalization. KW - p-Phenylenediamine KW - Multi-walled carbon nanotube KW - Nanocomposite KW - Oxidative polymerization PY - 2011 SN - 0250-4707 SN - 0973-7669 VL - 34 IS - 1 SP - 37 EP - 43 PB - Indian Academy of Sciences CY - Bangalore AN - OPUS4-24339 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kumelan, J. A1 - Tuma, Dirk A1 - Maurer, G. ED - Renon, H. T1 - Simultaneous solubility of carbon dioxide and hydrogen in the ionic liquid [hmim][Tf2N]: experimental results and correlation N2 - The solubility of a single gas as well as the simultaneous solubility of several gases in an ionic liquid is of great interest in many areas of chemical engineering, particularly in heterogeneous catalysis. One of the most interesting features involved in the study of the simultaneous solubility of several gases in a pure ionic liquid is the difference between experimental data and predictions for the simultaneous solubility (based on experimental data for the solubility of the single gases). The well soluble gas might act as a cosolvent or as an antisolvent for a sparsely soluble second gas. New experimental results and a correlation are presented for the simultaneous solubility of hydrogen (i.e., a sparsely soluble gas) and carbon dioxide (a well soluble gas) in the ionic liquid 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)amide ([hmim][Tf2N]) at temperatures between 293 K and 373 K and pressures up to about 9.2 MPa. The experimental results reveal that carbon dioxide acts as a cosolvent for hydrogen in that particular ionic liquid. A correlation shows that the cosolvency effect can be modeled by considering interaction parameters between hydrogen and carbon dioxide in liquid [hmim][Tf2N]. The correlation can also be used to quantify that cosolvency effect: one mole of carbon dioxide in 1000 g of [hmim][Tf2N] increases the solubility of (small amounts of) hydrogen by about 20%. KW - Simultaneous solubility of gases KW - Carbon dioxide KW - Hydrogen KW - Ionic liquids KW - [hmim][Tf2N] KW - 1-Hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)amide PY - 2011 DO - https://doi.org/10.1016/j.fluid.2011.08.013 SN - 0378-3812 VL - 311 SP - 9 EP - 16 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-24559 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Marwitz, Christian A1 - Stegemann, B. A1 - Breitkreiz, Maxim A1 - Spaltmann, Dirk A1 - Kloß, Heinz A1 - Woydt, Mathias A1 - Sturm, Heinz T1 - Correlation of adhesion force and electrical conductivity in Magnéli-type vanadium oxides and highly oriented pyrolytic graphite N2 - A correlation of adhesion force and electrical conductivity is established for a vanadium oxide and highly oriented pyrolytic graphite (HOPG). Adhesion forces were determined by analysis of pull-off forces obtained from force–distance curves with atomic force microscopy in ultrahigh vacuum, on clean surfaces and with defined contact conditions. The investigated samples include (i) different stoichiometries of Magnéli-type vanadium oxides (V3O5, V4O7, V6O11, and V7O13), which undergo metal-insulator-transitions as a function of temperature, (ii) the (0001) basal plane and the (10–10) prism plane of highly oriented pyrolytic graphite (HOPG), which differ in their respective perpendicular-plane electrical conductivities by several orders of magnitude, and (iii) the (100) surfaces of pure metal single crystals, i.e., silver (Ag), copper (Cu), iron (Fe) and gold (Au). It is shown, that the vanadium oxides as well as the graphite exhibit significantly lower adhesion forces in their electrical conductive state than in their non-electrical conductive state. The values obtained for the electrical conductive states are quantitatively confirmed by the measurements on the single crystal metals. KW - Adhesion force KW - HOPG KW - Vanadium oxide KW - Magnéli phases KW - Single crystal metals KW - Atomic force microscopy PY - 2011 DO - https://doi.org/10.1016/j.susc.2011.04.014 SN - 0039-6028 VL - 605 IS - 13-14 SP - 1271 EP - 1274 PB - Elsevier CY - Amsterdam AN - OPUS4-23953 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Anik, Yavuz A1 - Geburtig, Anja A1 - Sturm, Heinz A1 - Meyer-Plath, Asmus ED - Reichert, T. T1 - CarboLifeCycle -weathering-induced degradation of nanoparticle-functionalised composites N2 - A new research project 'CarboLifeCycle', funded by the German Federal Ministry of Education and Research (BMBF), investigates various nanoparticle release scenarios for carbon nanotube-containing polymer composites. The studied weathering concepts and conditions will be described. T2 - 5th European weathering symposium - Natural and artificial ageing of polymers CY - Lisbon, Portugal DA - 21.09.2011 KW - CNT KW - Nanoparticle KW - Weathering KW - Degradation PY - 2011 SN - 978-3-9813136-2-8 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 15 SP - 125 EP - 135 PB - GUS (Gesellschaft für Umweltsimulation) CY - Pfinztal AN - OPUS4-24503 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wolf, S. E. A1 - Müller, L. A1 - Barrea, R. A1 - Kampf, C.J. A1 - Leiterer, Jork A1 - Panne, Ulrich A1 - Hoffmann, T. A1 - Emmerling, Franziska A1 - Tremel, W. T1 - Carbonate-coordinated metal complexes precede the formation of liquid amorphous mineral emulsions of divalent metal carbonates N2 - During the mineralisation of metal carbonates MCO3 (M = Ca, Sr, Ba, Mn, Cd, Pb) liquid-like amorphous intermediates emerge. These intermediates that form via a liquid/liquid phase separation behave like a classical emulsion and are stabilized electrostatically. The occurrence of these intermediates is attributed to the formation of highly hydrated networks whose stability is mainly based on weak interactions and the variability of the metal-containing pre-critical clusters. Their existence and compositional freedom are evidenced by electrospray ionization mass spectrometry (ESI-MS). Liquid intermediates in non-classical crystallisation pathways seem to be more common than assumed. PY - 2011 DO - https://doi.org/10.1039/c0nr00761g SN - 2040-3364 SN - 2040-3372 IS - 3 SP - 1158 EP - 1165 PB - RSC Publ. CY - Cambridge AN - OPUS4-23355 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gusarova, Tamara A1 - Methven, B. A1 - Kipphardt, Heinrich A1 - Sturgeon, R. A1 - Matschat, Ralf A1 - Panne, Ulrich T1 - Calibration of double focusing glow discharge mass spectrometry instruments with pin-shaped synthetic standards N2 - Calibration of two commercially available glow discharge double focusing mass spectrometers, the VG 9000 and Element GD, is described using synthetic pin standards pressed from solution doped copper and zinc matrices. A special pressing die was developed for this purpose and optimal results were obtained with the highest possible pressures, i.e., 95 kN·cm- 2. This calibration approach permits the determination of trace element mass fractions down to µg·kg- 1 with small uncertainties and additionally provides traceability of the GD-MS results in the most direct manner to the SI (International System of Units). Results were validated by concurrent measurements of a number of compact copper and zinc certified reference materials. The impact of the sample pin cross-section (circular or square) was investigated with the use of a new pin-sample holder system for the Element GD. The pin-sample holder was designed by the manufacturer for pin-samples having circular cross-section; however, samples with square pin cross-section were also shown to provide acceptable results. Relative Sensitivity Factors for some 50 analytes in copper (VG 9000, Element GD) and zinc matrices (VG 9000) are presented. The field of applicability of GD-MS may be considerably extended via analysis of pin geometry samples based on their ease of preparation, especially with respect to the accuracy and traceability of the results and the enhanced number of analytes which can be reliably calibrated using such samples. KW - Glow discharge KW - Pin sample KW - Calibration PY - 2011 DO - https://doi.org/10.1016/j.sab.2011.12.001 SN - 0584-8547 SN - 0038-6987 VL - 66 IS - 11-12 SP - 847 EP - 854 PB - Elsevier CY - Amsterdam AN - OPUS4-25346 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gornushkin, Igor B. A1 - Shabanov, Sergej V. A1 - Panne, Ulrich T1 - Abel inversion applied to a transient laser induced plasma: implications from plasma modeling N2 - We test the effects of non-uniformity, non-transparency, and non-stationarity of a laser-induced plasma on the results obtained by the Abel inversion method. The method is commonly used for obtaining spatially resolved emissivity of axially symmetric non-homogeneous radiating objects. Besides the axial symmetry, the plasma is assumed to be optically thin. As the method addresses a certain plasma state, the plasma is required to be stationary during measurements. It is difficult to satisfy the aforementioned conditions for transient laser induced plasmas. As such the plasmas are not stationary; they have steep gradients of thermodynamic parameters that rapidly vary during the plasma evolution. Therefore, any conclusion based on time-integrated measurements and the corresponding data processing should account for these effects. In this work, we use the collision-dominated plasma model to generate time- and spatially resolved synthetic spectra. The spectra are processed by executing the Abel inversion using two numerical algorithms. Thus obtained spatially resolved plasma parameters (emissivity, temperature, and number density) are compared with the exact parameters used to set up the model. In doing so, the accuracy of the Abel inversion method is assessed. Special attention is paid to the dynamic aspect of the expanding plasma and possible errors which result from time-integrated measurements. PY - 2011 DO - https://doi.org/10.1039/c1ja10044k SN - 0267-9477 SN - 1364-5544 VL - 26 IS - 7 SP - 1457 EP - 1465 PB - Royal Society of Chemistry CY - London AN - OPUS4-25824 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rudtsch, S. A1 - Gusarova, Tamara A1 - Aulich, A. A1 - Fahr, M. A1 - Fischer, J. A1 - Kipphardt, Heinrich A1 - Matschat, Ralf A1 - Panne, Ulrich T1 - Procedure for the impurity-related correction at the indium fixed-point N2 - Determining the influence of impurities on the fixed-point emperatures of the ITS-90 requires the completion of several tasks. In this paper, the Progress made at Physikalisch-Technische Bundesanstalt (PTB) and BAMFederal Institute for Materials Research and Testing is presented and remaining questions are discussed. The projected characterization procedure at PTB, which is based on the established SIE method (sum of the individual estimates), using a new indium fixed-point cell is described as an example. This procedure includes an SI-traceable chemical Analysis of the material in the fixed-point cell with sufficiently low uncertainties, the individual experimental determination of the influence of the quantified impurities on the fixed-point temperature, and the establishment of direct links to the phase-transition temperatures of the national standard and of an assumed material of ideal purity. A characteristic difference to the common practice is the chemical analysis of the fixed-point metal being done after determining the cell’s freezing temperature. This allows for the detection and consideration of contamination and purification effects due to the filling process, or due to the contact with the carbon crucible and other parts of the fixed-point cell. A chemical analysis of an indium fixed-point was carried out by BAM with relative measurement uncertainties below 30 % which have not been previously achieved. The results provide evidence for the precipitation of some impurities, which is apparently inconsistent with the corresponding binary phase diagrams, but was explained in a recent publication. Implications for the use of the SIE method shall be described briefly at the end. KW - Chemical analysis KW - Fixed-points KW - Impurities KW - ITS-90 PY - 2011 DO - https://doi.org/10.1007/s10765-011-0915-0 SN - 0195-928X SN - 1572-9567 VL - 32 IS - 1-2 SP - 293 EP - 302 PB - Springer CY - Dordrecht AN - OPUS4-23373 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Herwig, Nadine A1 - Stephan, Kristin A1 - Panne, Ulrich A1 - Pritzkow, Wolfgang A1 - Vogl, Jochen T1 - Multi-element screening in milk and feed by SF-ICP-MS N2 - In this study, an analytical procedure for multi-element screening of 40 elements in milk and feed samples was developed. Three different digestion and two different calibration methods were tested for the best suitability. The analytical procedure for the quantification of minor and trace elements is based on sector field ICP-MS (SF-ICP-MS). The method validation revealed good agreement between the determined elemental mass fractions and the certified values of two milk and three feed reference materials. Milk samples of dairy cows at different feeding regimes were collected from two different farms. The results of our study showed significant differences of nine elemental mass fractions (Li, P, Mn, Co, Cu, Rb, Sr, Br, I) between milk from the two locations. Further, a correlation between the elemental mass fractions of milk and the ingested feed and water was observed. KW - Multi-element screening KW - SF-ICP-MS KW - Dairy cows KW - Milk KW - Feed KW - Water PY - 2011 DO - https://doi.org/10.1016/j.foodchem.2010.07.050 SN - 0308-8146 VL - 124 IS - 3 SP - 1223 EP - 1230 PB - Elsevier Ltd. CY - Amsterdam [u.a.] ; Jena AN - OPUS4-22042 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Merk, Virginia A1 - Schulte, Franziska A1 - Rooch, Heidemarie A1 - Feldmann, Ines A1 - Dörfel, Ilona A1 - Österle, Werner A1 - Panne, Ulrich A1 - Kneipp, Janina T1 - Surface-enhanced Raman scattering with silver nanostructures generated in situ in a sporopollenin biopolymer matrix N2 - Silver nanoparticles were generated based on citrate reduction in the ultrastructure of the sporopollenin biopolymer of Ambrosia artemisiifolia (ragweed) and Secale cereale (rye). The nanoparticles enable the acquisition of SERS spectra and thereby a vibrational characterization of the local molecular structure of sporopollenin. PY - 2011 DO - https://doi.org/10.1039/c0cc05326k SN - 0022-4936 SN - 0009-241x SN - 1359-7345 SN - 1364-548x N1 - Geburtsname von Merk, Virginia: Joseph, V. - Birth name of Merk, Virginia: Joseph, V. VL - 47 IS - 11 SP - 3236 EP - 3238 PB - Royal Society of Chemistry CY - Cambridge AN - OPUS4-23482 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weidner, Steffen A1 - Knappe, Patrick A1 - Panne, Ulrich T1 - MALDI-TOF imaging mass spectrometry of artifacts in 'dried droplet' polymer samples N2 - Matrix-assisted laser desorption/ionization-timeof-flight (MALDI-TOF) imaging of polystyrenes with various molecular masses was applied to study spatial molecular mass distribution of polymers in sample spots prepared by the 'dried droplet' method. When different solvents and target surfaces were examined, a segregation of single homologous polymers was observed depending upon the evaporation rate of the solvent. For the observed Patterns left by the evaporating droplet, a hypothesis is offered taking into account different hydrodynamic interactions and diffusion. The results illustrate that spot preparation using the conventionally 'dried droplet' method is prone to artifacts and should be avoided for reliable and reproducible MALDI mass spectrometry experiments with regards to the Determination of molecular masses and mass distributions. KW - MALDI KW - Mass spectrometry imaging KW - Polymer KW - Droplet PY - 2011 DO - https://doi.org/10.1007/s00216-011-4773-1 SN - 1618-2642 SN - 1618-2650 VL - 401 IS - 1 SP - 127 EP - 134 PB - Springer CY - Berlin AN - OPUS4-24538 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Walter, Astrid A1 - Panne, Ulrich A1 - Weller, Michael G. T1 - A novel immunoreagent for the specific and sensitive detection of the explosive triacetone triperoxide (TATP) N2 - Triacetone triperoxide (TATP) is a primary explosive, which was used in various terrorist attacks in the past. For the development of biosensors, immunochemical µ-TAS, electronic noses, immunological test kits, or test strips, the availability of antibodies of high quality is crucial. Recently, we presented the successful immunization of mice, based on the design, synthesis, and conjugation of a novel TATP derivative. Here, the long-term immunization of rabbits is shown, which resulted in antibodies of extreme selectivity and more than 1,000 times better affinity in relation to the antibodies from mice. Detection limits below 10 ng L-1 (water) were achieved. The working range covers more than four decades, calculated from a precision profile. The cross-reactivity tests revealed an extraordinary selectivity of the antibodies—not a single compound could be identified as a relevant cross-reactant. The presented immunoreagent might be a major step for the development of highly sensitive and selective TATP detectors particularly for security applications. KW - Organic peroxides KW - Terrorism KW - Biosensor development PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-240291 UR - http://www.mdpi.com/2079-6374/1/3/93 DO - https://doi.org/10.3390/bios1030093 SN - 2079-6374 VL - 1 IS - 3 SP - 93 EP - 106 PB - MDPI CY - Basel AN - OPUS4-24029 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Moreno-Gordaliza, E. A1 - Giesen, Charlotte A1 - Lázaro, A. A1 - Esteban-Fernández, D. A1 - Humanes, B. A1 - Canas, B. A1 - Panne, Ulrich A1 - Tejedor, A. A1 - Jakubowski, Norbert A1 - Gómez-Gómez, M.M. T1 - Elemental bioimaging in kidney by LA-ICP-MS as a tool to study nephrotoxicity and renal protective strategies in cisplatin therapies N2 - A laser ablation inductively coupled plasma mass spectrometry (LA–ICP–MS)-based methodology is presented for Pt, Cu, and Zn bioimaging on whole kidney 3 µm sagittal sections from rats treated with pharmacological doses of cisplatin, which were sacrificed once renal damage had taken place. Pt turned out to accumulate in the kidney cortex and corticomedullary junction, corresponding to areas where the proximal tubule S3 segments (the most sensitive cells to cisplatin nephrotoxicity) are located. This demonstrates the connection between platinum accumulation and renal damage proved by histological examination of HE-stained sections and evaluation of serum and urine biochemical parameters. Cu and Zn distribution maps revealed a significant displacement in cells by Pt, as compared to control tissues. A dramatic decrease in the Pt accumulation in the cortex was observed when cilastatin was coadministered with cisplatin, which can be related to its nephroprotective effect. Excellent imaging reproducibility, sensitivity (LOD 50 fg), and resolution (down to 8 µm) were achieved, demonstrating that LA–ICP–MS can be applied as a microscopic metal detector at cellular level in certain tissues. A simple and quick approach for the estimation of Pt tissue levels was proposed, based on tissue spiking. PY - 2011 DO - https://doi.org/10.1021/ac201933x SN - 0003-2700 SN - 1520-6882 VL - 83 IS - 20 SP - 7933 EP - 7940 PB - American Chemical Society CY - Washington, DC AN - OPUS4-24965 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Merk, Sven A1 - Shabanov, Sergej V. A1 - Gornushkin, Igor B. A1 - Panne, Ulrich T1 - Laser-induced plasma tomography by the Radon transform N2 - The Radon transform is tested as a method for reconstruction of the emissivity distribution of asymmetric laser induced plasmas. Two types of experiments were carried out. First, the plasma asymmetry is introduced via focusing the laser by a cylindrical lens to create plasma plumes elongated along the symmetry axis of the lens. Second, an asymmetric power distribution across the laser beam is created by reflecting the latter from a damaged mirror. Various effects on the quality of the plasma emissivity reconstructed by the Radon tomography method are investigated. The understanding of these effects appears to be essential to design a proper experimental setup to study LIBS plasmas by the Radon tomography method. It is demonstrated that the Radon tomography can successfully be used for experimental studies of asymmetric LIBS plasmas. KW - Radon transform KW - Laser induced plasma KW - LIBS KW - Plasma tomography PY - 2011 DO - https://doi.org/10.1039/c1ja10187k SN - 0267-9477 SN - 1364-5544 VL - 26 SP - 2483 EP - 2492 PB - Royal Society of Chemistry CY - London AN - OPUS4-24889 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Giesen, Charlotte A1 - Mairinger, T. A1 - Khoury, L. A1 - Müller, Larissa A1 - Jakubowski, Norbert A1 - Panne, Ulrich T1 - Multiplexed immunohistochemical detection of tumor markers in breast cancer tissue using laser ablation inductively coupled plasma mass spectrometry N2 - We optimized multiplexed immunohistochemistry (IHC) on breast cancer tissue. Up to 20 tumor markers are routinely evaluated for one patient, and thus, a common analysis results in a series of time consuming staining procedures. As an alternative, we used lanthanides for labeling of primary antibodies, which are applied in IHC. Laser ablation (LA) ICPMS was elaborated as a detection tool for multiplexed IHC of tissue sections. In this study, we optimized sample preparation steps and LA ICPMS parameters to achieve a sufficient signal-to-background ratio. The results prove the high selectivity of applied antibodies, which was sustained after labeling. Up to three tumor markers (Her 2, CK 7, and MUC 1) were detected simultaneously in a single multiplex analysis of a 5 µm thin breast cancer tissue at a laser spot size of 200 µm. Furthermore, the LA ICPMS results indicate a significantly higher expression level of MUC 1 compared to Her 2 and CK 7, which was not obvious from the conventionally stained tissue sections. PY - 2011 DO - https://doi.org/10.1021/ac2016823 SN - 0003-2700 SN - 1520-6882 N1 - Geburtsname von Müller, Larissa: Wäntig, L. - Birth name of Müller, Larissa: Wäntig, L. VL - 83 IS - 21 SP - 8177 EP - 8183 PB - American Chemical Society CY - Washington, DC AN - OPUS4-24966 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Giesen, Charlotte A1 - Müller, Larissa A1 - Mairinger, T. A1 - Drescher, Daniela A1 - Kneipp, Janina A1 - Roos, P.H. A1 - Panne, Ulrich A1 - Jakubowski, Norbert T1 - Iodine as an elemental marker for imaging of single cells and tissue sections by laser ablation inductively coupled plasma mass spectrometry N2 - A new laser ablation (LA)-ICP-MS method for single cell and cell nucleus imaging was developed. Therein, iodine was employed as an elemental dye for fibroblast cells and for thin tissue sections. At an incubation time of 60 s, iodine is located mainly within the cell nuclei. This effect was illustrated in fibroblast cells, and iodine signal within the cell nucleus was as high as 5 × 104 cps at 4 µm laser spot size. The surrounding cytoplasm was iodinated as well, but to a lesser extent. The spatial resolution attained was sufficient to detect even smaller cell nuclei within a liver biopsy tissue. Furthermore, iodine was successfully employed for biomolecule labeling and we demonstrated that iodine signal increased with increasing thickness of a palatine tonsil tissue. Thus, the use of iodine as an internal standard to correct for tissue inhomogeneities in LA-ICP-MS was investigated for the simultaneous detection of two tumor markers (Her 2 and CK 7) in breast cancer tissue. Additionally, lanthanide background resulting from glass ablation can be corrected for by Eu standardization. PY - 2011 DO - https://doi.org/10.1039/c1ja10227c SN - 0267-9477 SN - 1364-5544 N1 - Geburtsname von Müller, Larissa: Wäntig, L. - Birth name of Müller, Larissa: Wäntig, L. VL - 26 IS - 11 SP - 2160 EP - 2165 PB - Royal Society of Chemistry CY - London AN - OPUS4-24964 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schlegel, Moritz-Caspar A1 - Müller, Urs A1 - Panne, Ulrich A1 - Emmerling, Franziska T1 - Deciphering the sulfate attack of cementitious materials by high-resolution micro-x-ray diffraction N2 - The durability of cementitious materials depends, among others, on their resistance against chemical attack during the service life of a building. Here, we present an approach to analyze changes in the phase composition due to chemical attack in the form of sulfate ingress within the microstructure. Micro-X-ray (µX-ray) diffraction using synchrotron radiation in Debye–Scherrer (transmission) geometry allowed a spatial resolution of 10 µm. Phase transformations in the wake of damaging processes were observed in a detailed high-resolution imaging study. In comparison, samples containing supplementary cementitious materials were investigated and used to reconstruct the influence of different degeneration processes in detail. Additionally, reaction fronts within the bulk were localized by micro-X-ray fluorescence analysis. The experimental setup provided the possibility for analyzing the phase assemblage of a given sample without destroying the microstructure. The specimens for phase analysis are thick sections of the primary material and can be used for further microscopic analysis of the microstructure and microchemistry, e.g., scanning electron microscopy–energy-dispersive X-ray spectroscopy (SEM–EDX) or Raman spectroscopy. PY - 2011 DO - https://doi.org/10.1021/ac200181g SN - 0003-2700 SN - 1520-6882 VL - 83 IS - 10 SP - 3744 EP - 3749 PB - American Chemical Society CY - Washington, DC AN - OPUS4-23669 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dutschke, Andreas A1 - Lohrer, Christian A1 - Kurth, Lutz A1 - Seeger, Stefan A1 - Barthel, Mathias A1 - Panne, Ulrich T1 - Aerosol emissions from outdoor firework displays N2 - The results of investigations on the emission of particulate matter from three outdoor firework displays are presented. During these events, possibly harmful and toxic aerosol emissions were measured. Aerosols in the size range from 30 to 450 nm were detected. The maxima in the observed particle size distribution were between 80 and 175 nm, and the highest value determined was ~1.3 · 106 particles per cm³, while the highest mass concentration was approximately 1.8 mg m–3. The time-averaged particle mass concentration did, however, not exceed 0.7 mg m–3 (over 15 min). KW - Firework display KW - Particle size range KW - Particulate matter KW - Threshold values PY - 2011 DO - https://doi.org/10.1002/ceat.201100080 SN - 0930-7516 SN - 1521-4125 VL - 34 IS - 12 SP - 2044 EP - 2050 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-24929 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Leiterer, Jork A1 - Panne, Ulrich A1 - Thünemann, Andreas A1 - Weidner, Steffen T1 - Container-less polymerization in acoustically levitated droplets: an analytical study by GPC and MALDI-TOF mass spectrometry N2 - Molecular masses and end groups of polystyrene (PS) formed in a novel container-less polymerization strategy, based on levitated droplets in an acoustic trap, were determined by Gel Permeation Chromatography (GPC) and Matrix-assisted Laser Desorption/Ionization Time of Flight Mass spectrometry (MALDI-TOF MS). KW - Ultraschallfalle KW - MALDI Massenspektrometrie KW - Polymerisation PY - 2011 DO - https://doi.org/10.1039/c0ay00390e SN - 1759-9660 SN - 1759-9679 VL - 3 IS - 1 SP - 70 EP - 73 PB - RSC Publ. CY - Cambridge AN - OPUS4-23655 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar A1 - Müller, Urs A1 - Panne, Ulrich A1 - Emmerling, Franziska A1 - Meng, Birgit ED - Rogge, A. ED - Meng, B. T1 - Neue Wege in der Zementanalytik - Hochaufgelöste in-situ Sy-XRD T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 PY - 2011 SN - 978-3-9814281-0-0 SP - 18 EP - 24 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25197 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, Peter ED - Czichos, Horst ED - Saito, T. ED - Smith, L. T1 - Materials and the environment KW - Weathering KW - Total material requirement KW - Polymer PY - 2011 SN - 978-3-642-16640-2 DO - https://doi.org/10.1007/978-3-642-16641-9 SP - Chapter 15.1, 845 EP - 860 PB - Springer CY - Berlin, Heidelberg AN - OPUS4-24154 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nagli, L. A1 - Gaft, M. A1 - Gornushkin, Igor B. T1 - Comparison of single and double-pulse excitation during the earliest stage of laser induced plasma N2 - This paper deals with comparison of single-pulse (SP) and double-pulse (DP) excited plasmas during their earliest phase of life, from 0 to 500 ns. The samples are Si and Al and the irradiance per pulse is approximately 20 GWcm-2 under ambient conditions. It was found that at the beginning of a plasma lifespan, Si III and Al III ions were excited even under the SP excitation conditions and became much more abundant under DP excitation. The lifetime of doubly-ionized species was found to be very short, and after a delay of 200–300 ns they were not detected. The DP plasma differs from the SP plasma by the intensity of continuum radiation and by the width of emission lines, which are substantially narrower in the DP plasma. The intensity of light emitted from singly and, especially, doubly-ionized species is higher compared with neutral atoms; whereas the decay time of both neutral and ionized species is longer. An excitation mechanism for the DP plasma is proposed enabling qualitative and a quantitative explanation of the experimental data. KW - Laser induced plasma KW - Single ionization KW - Double ionization KW - Collision dominated plasma model PY - 2011 DO - https://doi.org/10.1007/s00216-011-4806-9 SN - 1618-2642 SN - 1618-2650 VL - 400 IS - 10 SP - 3207 EP - 3216 PB - Springer CY - Berlin AN - OPUS4-25826 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Höhse, Marek A1 - Gornushkin, Igor B. A1 - Merk, Sven A1 - Panne, Ulrich T1 - Assessment of suitability of diode pumped solid state lasers for laser induced breakdown and Raman spectroscopy N2 - The potential of a diode pumped solid state (DPSS) laser for laser induced breakdown spectroscopy (LIBS) and Raman spectroscopy was investigated. The DPSS laser operating at repetition rates of 1 Hz–200 kHz, pulse energy of ~1 mJ, and pulse duration of ~20 ns was added to a conventional LIBS system equipped with the flashlamp-pumped Nd:YAG laser (10 Hz, 400 mJ, 6 ns) to directly compare the two laser systems. Despite the lower mass ablated per laser pulse (~several nanograms) and a weaker plasma, the total mass ablated per measurement interval (~1 s) and total emission signal were significantly higher than those obtained with the flashlamp pumped Nd:YAG laser. This resulted in the improved signal-to-noise ratio and better limits of detection (LOD). The best LODs were obtained for Cu, Cr and Ni in ultrapure standard iron samples, 0.7 ppm, 1 ppm and 5 ppm, correspondingly. The plasma from the DPSS laser was characterized in terms of its radiative properties, temperature, and shockwave propagation speed. The suitability of this laser for LIBS-Raman was demonstrated by mapping the elemental and molecular composition of a mineral sample. The results strongly imply that DPSS lasers are the promising source for LIBS, Raman, or combined LIBS-Raman spectroscopy. PY - 2011 DO - https://doi.org/10.1039/c0ja00038h SN - 0267-9477 SN - 1364-5544 VL - 26 IS - 2 SP - 414 EP - 424 PB - Royal Society of Chemistry CY - London AN - OPUS4-22943 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gornushkin, Igor B. A1 - Merk, Sven A1 - Höhse, Marek A1 - Panne, Ulrich T1 - Laser Induced Breakdown and Raman Spectroscopy with Diode Pumped Solid State (DPSS) Lasers T2 - ANAKON 2011 CY - Zurich, Switzerland DA - 2011-03-22 PY - 2011 AN - OPUS4-24881 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gornushkin, Igor B. A1 - Panne, Ulrich T1 - Laser Induced Breakdown Spectroscopy (LIBS) and Raman Spectroscopy for Material Analysis T2 - 16. Tagung Festkörperanalytik CY - Vienna, Austria DA - 2011-07-04 PY - 2011 AN - OPUS4-24885 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Merk, Sven A1 - Höhse, Marek A1 - Gornushkin, Igor B. A1 - Panne, Ulrich T1 - Laser Induzierte Plasmaspektroskopie und Raman Spektroskopie mit Diodengepumpten Festkörperlasern T2 - 1. Berline Chemie Symposium 2011 CY - Berlin, Germany DA - 2011-04-07 PY - 2011 AN - OPUS4-23739 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Demidov, Alexandr A1 - Gornushkin, Igor B. A1 - Panne, Ulrich T1 - Standardless Analysis of Aluminium Alloys based on Modeling of Laser Induced Plasma T2 - NASLIBS 2011 CY - Izmir, Turkey DA - 2011-09-11 PY - 2011 AN - OPUS4-24884 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Glaus, Reto A1 - Kadenkin, Alexander A1 - Gornushkin, Igor B. A1 - Günther, D. T1 - Portable laser ablation sampling using a diode pumped solid state laser T2 - Fall Meeting of the Swiss Society 2011 CY - Lausanne, Switzerland DA - 2011-09-09 PY - 2011 AN - OPUS4-24631 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Matiaske, Anna-Maria A1 - Gornushkin, Igor B. A1 - Panne, Ulrich T1 - Double-Pulse-LIBS for Analysis of Molton Glass T2 - EMSLIBS 2011 CY - Izmir, Turkey DA - 2011-09-11 PY - 2011 AN - OPUS4-24880 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gornushkin, Igor B. A1 - Nagli, L. A1 - Gaft, M. T1 - Fraunhofer Lines in Double Pulse Laser Induced Plasma T2 - NASLIBS 2011 CY - Clearwater, FL, USA DA - 2011-07-18 PY - 2011 AN - OPUS4-24883 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shcheglov, Pavel A1 - Gumenyuk, Andrey A1 - Gornushkin, Igor B. A1 - Rethmeier, Michael T1 - Experimental Investigation of the Laser-Plume Interaction during High Power Fiber Laser Welding T2 - 30th International Congress on Applications of Laser & Electro-Optics (ICALEO) CY - Orlando, FL, USA DA - 2011-10-23 PY - 2011 AN - OPUS4-24768 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gornushkin, Igor B. A1 - Kadenkin, Alexander A1 - Bierstedt, Andreas A1 - Panne, Ulrich A1 - Riedel, Jens A1 - Florek, S. A1 - Geisler, S. T1 - Novel low cost compact Echelle spectrograph for laser induced breakdown spectroscopy with a diode pumped solid state laser T2 - Colloquium Spectroscopicum Internationale XXXVII CY - Rio de Janeiro, Brazil DA - 2011-08-28 PY - 2011 AN - OPUS4-24633 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dülsen, Steffen A1 - Hofmann-Böllinghaus, Anja A1 - Krause, Ulrich T1 - Untersuchung zu Brandursachen und Brandverlauf bei Busbränden T2 - vfdb-Jahrestagung 2011 CY - Berlin, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23816 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeger, Stefan A1 - Barthel, Mathias T1 - Prüfverfahren Blauer Engel für Bürodruckgeräte unter Berücksichtigung ultrafeiner Partikelemissionen, Abschluss des Ufoplan-Vorhabens T2 - 18. WaBoLu-Innenraumtage, UBA Berlin CY - Berlin, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-24377 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dülsen, Steffen A1 - Hofmann-Böllinghaus, Anja A1 - Krause, Ulrich T1 - Brandschutzanforderungen an die Materialien von Kraftomnibussen - Signifikante Zunahme von brennbaren Kunststoffteilen stellt eine Gefahr dar KW - Busbrand KW - Materialien KW - Brandschutz PY - 2011 SN - 0006-9094 VL - 7 SP - 524 EP - 527 PB - Kohlhammer CY - Stuttgart AN - OPUS4-24169 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hofmann-Böllinghaus, Anja A1 - Mühlnikel, Rüdiger T1 - Experimental and numerical investigation of fire development in a real fire in a five-storey apartment building N2 - A fire in a five-storey apartment building was investigated experimentally and numerically. The room of origin of the fire was a living room in the second floor and the fire was started by a candle on a television set. The fire spread externally over the building faccade and internally along the staircase and affected all the flats above leading to two fatalities. It is estimated that the fire was discovered minutes after ignition and the fire service was called very shortly after the detection and was at the scene 9?min after the call. By this time large sections of the façade were on fire already. The rapid fire that spread over the façade and the staircase necessitated detailed investigations. Compliance of building products with the building regulations was investigated. One conclusion of the investigations was that the person who caused the fire by leaving the candle on the TV set unattended should not be held responsible for the two fatalities in the upper floors. KW - Fire investigation KW - Real fire KW - Building products KW - Numerical modelling KW - Apartment building PY - 2011 DO - https://doi.org/10.1002/fam.1065 SN - 0308-0501 SN - 1099-1018 N1 - Geburtsname von Hofmann-Böllinghaus, Anja: Hofmann, A. - Birth name of Hofmann-Böllinghaus, Anja: Hofmann, A. VL - 35 IS - 7 SP - 453 EP - 462 PB - Heyden CY - London AN - OPUS4-22776 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kempel, Florian A1 - Hofmann-Böllinghaus, Anja A1 - Krause, Ulrich T1 - Numerical experiments on the influence of the distributation of fire load and ignition location on the fire spread in a family home T2 - Proc. of the 11th Symposium of Fire Safety Science CY - College Park, MD, USA DA - 2011-06-19 PY - 2011 AN - OPUS4-24190 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Simone A1 - Deubel, Jan A1 - Raspe, Tina A1 - Fettig, Ina A1 - Piechotta, Christian A1 - Seeger, Stefan A1 - Rothhardt, Monika T1 - Chemical analysis of scorch marks during smouldering of spruce wood - Fire debris, particles and smoke gases T2 - 10 th International IAFSS Symposium CY - College Park, MD, USA DA - 2011-06-19 PY - 2011 AN - OPUS4-23954 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald A1 - Seeger, Stefan A1 - Reinhardt, F. A1 - Waldschläger, U. A1 - Pollakowski, B. A1 - Beckhoff, B. T1 - Size selected nanoparticle quantifciation of deposited aerosol by GIXRF T2 - European Aerosol Conference 2011 CY - Manchester, England DA - 2011-09-04 PY - 2011 AN - OPUS4-24409 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tag, Mathias A1 - Bresch, Harald A1 - Seeger, Stefan T1 - Expositionsverfahren für toxikologische Untersuchungen mit Nanopartikeln T2 - Seminar für Aerosolphysik CY - Karlsruhe, Germany DA - 2011-02-02 PY - 2011 N1 - Geburtsname von Tag, Mathias: Deutscher, M. - Birth name of Tag, Mathias: Deutscher, M. AN - OPUS4-23435 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Werrel, Martin A1 - Deubel, Jan A1 - Krüger, Simone A1 - Hofmann-Böllinghaus, Anja T1 - Oxygen-reduced Cone Calorimeter - Characteristic effects on the calculation of the heat release rate T2 - ISO-Meeting CY - Brussels, Belgium DA - 2011-11-02 PY - 2011 AN - OPUS4-24710 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiele, Marc A1 - Pirskawetz, Stephan A1 - Baeßler, Matthias A1 - Rogge, Andreas T1 - Untersuchung der Schädigungsevolution in Beton unter Ermüdungsbeanspruchung mit Hilfe der Schallemissionsanalyse N2 - Unter zyklischen Belastungen findet im Beton, wie bei anderen Materialien auch, ein Ermüdungsprozess statt, der letztlich im Versagen des Materials enden kann. Im derzeitigen Erkenntnisstand zum Materialverhalten des Betons gibt es gerade bei dessen Ermüdungsverhalten noch viele nicht oder nicht ausreichend geklärte Fragestellungen. Deshalb wurde in Laborversuchen das Ermüdungsverhalten von Beton unter Druckschwellbeanspruchungen untersucht. Im Fokus dieser Untersuchungen standen dabei die während der Lebensdauer im Materialgefüge ablaufenden Prozesse, die zur Schädigung des Gefüges und schließlich auch zum Ermüdungsversagen führen können. In den Ermüdungsversuchen wurden versuchsbegleitend Dehnungsmessungen, Ultraschall-Laufzeitmessungen und Schallemissionsmessungen an den Proben zur Erfassung der Schädigungsevolution eingesetzt. Die Schallemissionsmessung ist dabei ein wichtiges Instrument, da sie die Rissentwicklungsprozesse detektiert, die die Ursache für die Materialschädigung sind. Mit ihr konnten die unterschiedlichen Phasen der Rissentwicklungen über die gesamte Lebensdauer der Betonproben festgestellt werden. Diese Phasen sind gekennzeichnet durch sich stabilisierende, stabile und instabile Rissprozesse, die entsprechende Auswirkungen auf das Materialverhalten haben. Ein Vergleich mit den Ergebnissen der anderen Messtechniken zeigt den entsprechenden Einfluss der Rissentwicklungen auf die Materialeigenschaften des Betons. T2 - 18. Kolloquium Schallemission CY - Wetzlar, Deutschland DA - 27.10.2011 KW - Beton KW - Ermüdung KW - Schallemission PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-247223 SN - 978-3-940283-37-5 IS - DGZfP-BB 131 (Vortrag 02) SP - 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-24722 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - El-Hasan, T. A1 - Szczerba, Wojciech A1 - Buzanich, Günter A1 - Radtke, Martin A1 - Riesemeier, Heinrich A1 - Kersten, M. T1 - Cr(VI)/Cr(III) and As(V)/As(III) ratio assessments in Jordanian spent oil shale produced by aerobic combustion and anaerobic pyrolysis N2 - With the increase in the awareness of the public in the environmental impact of oil shale utilization, it is of interest to reveal the mobility of potentially toxic trace elements in spent oil shale. Therefore, the Cr and As oxidation state in a representative Jordanian oil shale sample from the El-Lajjoun area were investigated upon different lab-scale furnace treatments. The anaerobic pyrolysis was performed in a retort flushed by nitrogen gas at temperatures in between 600 and 800 °C (pyrolytic oil shale, POS). The aerobic combustion was simply performed in porcelain cups heated in a muffle furnace for 4 h at temperatures in between 700 and 1000 °C (burned oil shale, BOS). The high loss-on-ignition in the BOS samples of up to 370 g kg–1 results from both calcium carbonate and organic carbon degradation. The LOI leads to enrichment in the Cr concentrations from 480 mg kg–1 in the original oil shale up to 675 mg kg–1 in the ≥850 °C BOS samples. Arsenic concentrations were not much elevated beyond that in the average shale standard (13 mg kg–1). Synchrotron-based X-ray absorption near-edge structure (XANES) analysis revealed that within the original oil shale the oxidation states of Cr and As were lower than after its aerobic combustion. Cr(VI) increased from 0% in the untreated or pyrolyzed oil shale up to 60% in the BOS ash combusted at 850 °C, while As(V) increased from 64% in the original oil shale up to 100% in the BOS ash at 700 °C. No Cr was released from original oil shale and POS products by the European compliance leaching test CEN/TC 292 EN 12457-1 (1:2 solid/water ratio, 24 h shaking), whereas leachates from BOS samples showed Cr release in the order of one mmol L–1. The leachable Cr content is dominated by chromate as revealed by catalytic adsorptive stripping voltammetry (CAdSV) which could cause harmful contamination of surface and groundwater in the semiarid environment of Jordan. KW - Trace-elements KW - Fly-ash KW - Speciation KW - Chromium KW - Sediments KW - Behavior KW - Metals KW - Xanes KW - Cr KW - Transformation PY - 2011 DO - https://doi.org/10.1021/es200695e SN - 0013-936X SN - 1520-5851 VL - 45 IS - 22 SP - 9799 EP - 9805 PB - ACS Publ. CY - Washington, DC AN - OPUS4-25290 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Cabral, A.R. A1 - Radtke, Martin A1 - Munnik, F. A1 - Lehmann, B. A1 - Reinholz, Uwe A1 - Riesemeier, Heinrich A1 - Tupinambá, M. A1 - Kwitko-Ribeiro, R. T1 - Iodine in alluvial platinum-palladium nuggets: evidence for biogenic precious-metal fixation N2 - Synchrotron radiation-induced X-ray fluorescence (SR-XRF) spectrometry was applied to determine iodine concentrations in alluvial Pt–Pd aggregates with delicate morphological features from Córrego Bom Sucesso, Minas Gerais, Brazil. The millimetre-sized botryoidal and rod-shaped grains of alluvial Pt–Pd–Hg intermetallic compounds have surprisingly high concentrations of iodine, in the range from 10 to ~ 120 μg/g. Because iodine is a strongly biophile element, known to be enriched in peatlands and plant remains in soils by microbial activity, its concentration in the Pt–Pd nuggets suggests biogenic precious-metal fixation in the aqueous alluvial milieu. Biogenic and inorganic processes, such as bioreduction and electrochemical metal accretion, could mutually have contributed to the growth of nanoparticles, formed on organic templates, to millimetric Pt–Pd nuggets. KW - Lodine KW - Pt-Pd nuggets KW - Córrego Bom Sucesso KW - Minas Gerais KW - Brazil PY - 2011 DO - https://doi.org/10.1016/j.chemgeo.2010.12.003 SN - 0009-2541 SN - 1872-6836 VL - 281 IS - 1-2 SP - 125 EP - 132 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-23174 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Constantinescu, B. A1 - Vasilescu, A. A1 - Radtke, Martin A1 - Reinholz, Uwe T1 - The Use of Micro-Synchrotron Radiation X-Ray Fluorescence For Studies On Gold And Copper Provenance Of Romanian Prehistoric Objects T2 - 39th annual international conference on Computer Applications and Quantitative Methods in Archaeology - CAA2011 CY - Beijing, China DA - 2011-04-12 PY - 2011 AN - OPUS4-22563 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Radtke, Martin A1 - Scharf, Oliver A1 - Reinholz, Uwe A1 - Riesemeier, Heinrich A1 - Buzanich, Günter A1 - Bjeoumikhov, A. A1 - Gubzhokov, Renat A1 - Wedell, R. A1 - Soltau, H. A1 - Ihle, S. A1 - Ordavo, I. A1 - Langhoff, N. T1 - The colour X-ray camera: Basics, Applications and Perspectives T2 - 21st International Congress on X-ray Optics and Microanalysis (ICXOM21) CY - Campinas, Brazil DA - 2011-09-05 PY - 2011 AN - OPUS4-24024 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Radtke, Martin A1 - Scharf, O. A1 - Bjeoumikova, S. A1 - Wedell, R. A1 - Soltau, H. A1 - Ordavo, I. A1 - Langhoff, N. A1 - Buzanich, Günter A1 - Reinholz, Uwe A1 - Gubzhokov, Renat A1 - Kuehbacher, M. A1 - Giere, P. A1 - Riesemeier, Heinrich T1 - Non-invasive spatial scanning for iron and calcium in the enamel of a red toothed shrew, Sorex araneus (Soricidae, Lipotyphla) T2 - 85th Annual Conference of the German Society of Mammalogy CY - Luxembourg City, Luxembourg DA - 2011-09-13 PY - 2011 AN - OPUS4-24025 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scharf, Oliver A1 - Arkadiev, V. A1 - Wedell, R. A1 - Langhoff, N. A1 - Ihle, S. A1 - Soltau, H. A1 - Ordavo, I. A1 - Buzanich, Günter A1 - Gubzhokov, Renat A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Riesemeier, Heinrich T1 - An Energy-Resolving X-RAY Camera as a novel tool in the full-field X-Ray analysis of medical and biological samples T2 - SFM`11 Saratov Fall Meeting CY - Saratov, Russia DA - 2011-09-27 PY - 2011 AN - OPUS4-25268 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Radtke, Martin A1 - Scharf, Oliver A1 - Buzanich, Günter A1 - Reinholz, Uwe A1 - Riesemeier, Heinrich A1 - Arkadiev, V. A1 - Wedell, R. A1 - Bjeoumikhov, A. A1 - Langhoff, N. A1 - Ihle, S. A1 - Soltau, H. A1 - Ordavo, I. T1 - The Colour X-Ray Camera: Basics, Applications and Perspectives T2 - Third Joint BER II and Bessy II User`s Meeting CY - Berlin, Germany DA - 2011-11-30 PY - 2011 AN - OPUS4-25269 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Szczerba, Wojciech A1 - Riesemeier, Heinrich A1 - Reinholz, Uwe A1 - Radtke, Martin A1 - Thünemann, Andreas A1 - Fenger, R. L. A1 - Rademann, Klaus A1 - Kaiser, Jens A1 - Yu, L. A1 - Ballauff, M. T1 - XAFS Studies on Catalytic Nanoparticle Systems T2 - SHP-Kolleg Gdansk 2011 "How Science Spies On And Technology Imitates Nature" CY - Gdansk, Poland DA - 2011-09-25 PY - 2011 AN - OPUS4-24990 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reinholz, Uwe A1 - Scharf, Oliver A1 - Bjeoumikhova, Zemfira A1 - Gubzhokov, Renat A1 - Radtke, Martin A1 - Buzanich, Günter A1 - Riesemeier, H. A1 - Ihle, S. A1 - Ordavo, I. A1 - Wedell, R. T1 - A novel device for elemental distribution imaging: the color x-ray camera T2 - Third Joint BER II and BESSY II Users´ Meeting CY - Berlin, Germany DA - 2011-11-30 PY - 2011 AN - OPUS4-25123 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühn, Andreas A1 - Reinholz, Uwe A1 - Riesemeier, Heinrich A1 - Radtke, Martin A1 - Panne, Ulrich T1 - Fast spatially resolved elemental distribution patters for TXRF samples, T2 - Konferenz TXRF CY - Dortmund, Germany DA - 2011-06-06 PY - 2011 AN - OPUS4-24098 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eilbracht, H. A1 - Radtke, Martin A1 - Armbruster, B. A1 - Reiche, I. T1 - Precious metalwork from the Viking age - the manufacturing of the Hiddensee jewellery T2 - Archaeometallurgy in Europe 2011 CY - Bochum, Germany DA - 2011-06-29 PY - 2011 AN - OPUS4-24027 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühn, Andreas A1 - Scharf, Oliver A1 - Ordavo, I. A1 - Riesemeier, Heinrich A1 - Reinholz, Uwe A1 - Radtke, Martin A1 - Ostermann, Markus A1 - Berger, Achim A1 - Panne, Ulrich T1 - Schnelle ortsaufgelöste Messung von Elementverteilungen mit Röntgenfluoreszenz T2 - 3rd Joint HZB BER II and BESSY // Users´ Meeting CY - Berlin, Germany DA - 2011-11-30 PY - 2011 AN - OPUS4-24983 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Radtke, Martin T1 - The Color X-Ray Camera: Basics, Applications and Perspectives T2 - Third Joint BER II and BESSY II Users´ Meeting CY - Berlin, Germany DA - 2011-11-30 PY - 2011 AN - OPUS4-25127 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Radtke, Martin T1 - Materialforschung an der BAMline T2 - DGM-Fachausschuss Werkstoffcharakterisierung mit Strahllinien CY - Berlin, Germany DA - 2011-05-27 PY - 2011 AN - OPUS4-24026 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Radtke, Martin T1 - Röntgenfluoreszenzanalyse mit Synchrotronstrahlung an der Bundesanstalt für Materialforschung und -prüfung (BAM), Berlin T2 - Seminar: "Strahlenphysikalische Anwendungen in Technik und Medizin" CY - Vienna, Austria DA - 2011-01-19 PY - 2011 AN - OPUS4-23265 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scharf, O. A1 - Bjeoumikova, S. A1 - Gubzhokov, Renat A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Riesemeier, Heinrich A1 - Wedell, R. A1 - Soltau, H. A1 - Ihle, S. T1 - An energy and spatial resolving X-Ray camera T2 - Technart 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-23079 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scharf, Oliver A1 - Ihle, S. A1 - Ordavo, I. A1 - Arkadiev, V. A1 - Bjeoumikhov, A. A1 - Bjeoumikhova, S. A1 - Buzanich, Günter A1 - Gubzhokov, R. A1 - Günther, A. A1 - Hartmann, R. A1 - Kühbacher, M. A1 - Lang, M. A1 - Langhoff, N. A1 - Liebel, A. A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Riesemeier, Heinrich A1 - Soltau, H. A1 - Strüder, L. A1 - Thünemann, Andreas A1 - Wedell, R. T1 - Compact pnCCD-based X-ray camera with high spatial and energy resolution: a color X-ray camera N2 - For many applications there is a requirement for nondestructive analytical investigation of the elemental distribution in a sample. With the improvement of X-ray optics and spectroscopic X-ray imagers, full field X-ray fluorescence (FF-XRF) methods are feasible. A new device for high-resolution X-ray imaging, an energy and spatial resolving X-ray camera, is presented. The basic idea behind this so-called 'color X-ray camera' (CXC) is to combine an energy dispersive array detector for X-rays, in this case a pnCCD, with polycapillary optics. Imaging is achieved using multiframe recording of the energy and the point of impact of single photons. The camera was tested using a laboratory 30 µm microfocus X-ray tube and synchrotron radiation from BESSY II at the BAMline facility. These experiments demonstrate the suitability of the camera for X-ray fluorescence analytics. The camera simultaneously records 69696 spectra with an energy resolution of 152 eV for manganese Kα with a spatial resolution of 50 µm over an imaging area of 12.7 × 12.7 mm². It is sensitive to photons in the energy region between 3 and 40 keV, limited by a 50 µm beryllium window, and the sensitive thickness of 450 µm of the chip. Online preview of the sample is possible as the software updates the sums of the counts for certain energy channel ranges during the measurement and displays 2-D false-color maps as well as spectra of selected regions. The complete data cube of 264 × 264 spectra is saved for further qualitative and quantitative processing. KW - Color X-ray camera KW - X-ray fluorescence KW - pnCCD KW - Polycapillary optic KW - Synchrotron radiation PY - 2011 DO - https://doi.org/10.1021/ac102811p SN - 0003-2700 SN - 1520-6882 VL - 83 IS - 7 SP - 2532 EP - 2538 PB - American Chemical Society CY - Washington, DC AN - OPUS4-23948 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scharf, O. A1 - Reinholz, Uwe A1 - Radtke, Martin A1 - Riesemeier, Heinrich A1 - Buzanich, Günter A1 - Bjeoumikova, S. A1 - Gubzhokov, R. A1 - Langhoff, N. A1 - Soltau, H. A1 - Wedell, R. A1 - Ordavo, I. T1 - A novel device for elemental distribution imaging: A color X-Ray Camera T2 - Jahrestagung der Deutschen Gesellschaft für Biomaterialien (DGBM) CY - Giessen, Germany DA - 2011-11-01 PY - 2011 AN - OPUS4-23974 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Constantinescu, B. A1 - Vasilescu, A. A1 - Radtke, Martin A1 - Reinholz, Uwe T1 - A study on gold and copper provenance for Romanian prehistoric objects using micro-SR XRF N2 - This study intends to clarify the metal provenance of gold archaeological items using the variation of the Au–Ag ratio and the presence of trace elements as Sn, Sb, Te, and Pb, concentrating on gold Dacian Koson coins, recovered recently. It also extends the area of our investigations to the copper provenance of Bronze Age artifacts—axes, sickles, and celts—found on Romanian territory. The experiments were performed by micro-SR XRF at BESSY Berlin, at the BAM-line facility. Two types of coins (Koson, with and without monogram) were analysed. The conclusions we reached were that most of the monogram coins are made from refined gold (3–5% Ag, less than 0.5% Cu), while the without monogram coins are made from native Transylvanian gold (9–20% Ag, 0.5–2% Cu), of alluvial origin, proved by the presence of Sn, Sb and Te embedded in the gold. The problem of provenance for prehistoric Romanian copper and bronze objects consists in linking their elemental compositional patterns to the ones of the Bronze Age regional mines from Bulgaria, Serbia or Transylvania, most likely used as ore sources for their manufacture. The studied samples present relevant traces of As, Ag, Sb, and Co, suggesting the most probable use of copper from Serbia or northern Bulgaria for their manufacture. KW - X-ray fluorescence KW - Synchrotron radiation KW - Proton induced X-ray emission KW - Archaeometry KW - Gold PY - 2011 DO - https://doi.org/10.1039/c0ja00215a SN - 0267-9477 SN - 1364-5544 VL - 26 IS - 5 SP - 917 EP - 921 PB - Royal Society of Chemistry CY - London AN - OPUS4-23191 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Grunewald, Christian A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Buzanich, Günter A1 - Riesemeier, Heinrich T1 - SRXRF-measurements at non-planar objects: automatic determination of the angle of incidence of the exciting X-ray N2 - For quantitative SRXRF measurements the angle of incidence of the incoming X-ray beam is an important factor. When the sample is focused by a long-range-microscope, the determination of the angle can be automatized using a simple algorithm. This was developed to improve the orientation of especially round or ornate samples. As a side effect the three dimensional surface can be reconstructed, too. KW - X-ray fluorescence KW - Synchrotron radiation KW - Long-range microscope PY - 2011 DO - https://doi.org/10.1039/c0ja00237b SN - 0267-9477 SN - 1364-5544 VL - 26 IS - 5 SP - 1088 EP - 1089 PB - Royal Society of Chemistry CY - London AN - OPUS4-23193 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ordavo, I. A1 - Ihle, S. A1 - Arkadiev, V. A1 - Scharf, Oliver A1 - Soltau, H. A1 - Bjeoumikhov, A. A1 - Bjeoumikhova, S. A1 - Buzanich, Günter A1 - Gubzhokov, R. A1 - Günther, A. A1 - Hartmann, R. A1 - Holl, P. A1 - Kimmel, N. A1 - Kühbacher, M. A1 - Lang, M. A1 - Langhoff, N. A1 - Liebel, A. A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Riesemeier, Heinrich A1 - Schaller, G. A1 - Schopper, F. A1 - Strüder, L. A1 - Thamm, C. A1 - Wedell, R. T1 - A new pnCCD-based color X-ray camera for fast spatial and energy-resolved measurements N2 - We present a new high resolution X-ray imager based on a pnCCD detector and a polycapillary optics. The properties of the pnCCD like high quantum efficiency, high energy resolution and radiation hardness are maintained, while color corrected polycapillary lenses are used to direct the fluorescence photons from every spot on a sample to a corresponding pixel on the detector. The camera is sensitive to photons from 3 to 40 keV with still 30% quantum efficiency at 20 keV. The pnCCD is operated in split frame mode allowing a high frame rate of 400 Hz with an energy resolution of 152 eV for Mn Kα (5.9 keV) at 450 kcps. In single-photon counting mode (SPC), the time, energy and position of every fluorescence photon is recorded for every frame. A dedicated software enables the visualization of the elements distribution in real time without the need of post-processing the data. A description of the key components including detector, X-ray optics and camera is given. First experiments show the capability of the camera to perform fast full-field X-Ray Fluorescence (FF-XRF) for element analysis. The imaging performance with a magnifying optics (3×) has also been successfully tested. KW - X-ray CCD camera KW - pnCCD KW - Fast X-ray imaging KW - XRF KW - Full-field X-ray fluorescence KW - Elemental analysis KW - High quantum efficiency KW - High energy resolution KW - Polycapillary optics PY - 2011 DO - https://doi.org/10.1016/j.nima.2011.05.080 SN - 0168-9002 SN - 0167-5087 VL - 654 SP - 250 EP - 257 PB - North-Holland CY - Amsterdam AN - OPUS4-24370 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hodoroaba, Vasile-Dan A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Riesemeier, Heinrich A1 - Vincze, L. A1 - Reuter, Dirk T1 - X-ray scattering in X-ray fluorescence spectra with X-ray monochromatic, polarised excitation - modelling, experiment, and Monte-Carlo simulation N2 - A systematic series of measurements has been carried out with monochromatic X-ray excitation with synchrotron radiation in order to check a physical model on X-ray scattering. The model has recently been successfully tested for the case of polychromatic, unpolarised excitation emitted by an X-ray tube. Our main purpose is the modelling of a physical background in X-ray fluorescence spectra, so that improved quantitative results can be achieved especially for strongly scattering specimens. The model includes single Rayleigh and Compton scattering in the specimen, the effect of bound electrons, the challenging Compton broadening and the polarisation degree. Representative specimens, measurement geometries and excitation energies have been selected with synchrotron monochromatic light at BAMline/BESSY II. Monte-Carlo simulations have been also carried out in order to evaluate the quality of the results achieved with the model. KW - X-ray scattering KW - Monochromatic excitation KW - Polarisation KW - Modelling KW - Monte-Carlo simulation PY - 2011 DO - https://doi.org/10.1016/j.nimb.2011.04.009 SN - 0168-583X SN - 1872-9584 VL - 269 IS - 13 SP - 1493 EP - 1498 PB - Elsevier CY - Amsterdam AN - OPUS4-23765 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühn, Andreas A1 - Scharf, Oliver A1 - Ordavo, I. A1 - Riesemeier, Heinrich A1 - Reinholz, Uwe A1 - Radtke, Martin A1 - Ostermann, Markus A1 - Berger, Achim A1 - Panne, Ulrich T1 - Schnelle ortsaufgelöste Messungen der Elementverteilung in TXRF-Proben T2 - Konferenz PRORA 2011 CY - Berlin, Germany DA - 2011-11-24 PY - 2011 AN - OPUS4-24981 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kühn, Andreas A1 - Scharf, Oliver A1 - Ordavo, I. A1 - Riesemeier, Heinrich A1 - Reinholz, Uwe A1 - Radtke, Martin A1 - Berger, Achim A1 - Ostermann, Markus A1 - Panne, Ulrich T1 - Pushing the limits for fast spatially resolved elemental distribution patterns N2 - A new setup for fast spatially resolved measurements of elemental trace amounts under total reflection conditions using a new colour X-ray camera is described. Samples prepared on conventional total reflection X-ray fluorescence (TXRF) reflectors were measured at BESSY II synchrotron. A spatial resolution of 50 × 50 µm² was obtained, while the required time for the investigation of a 10 × 10 mm² sample is 30 seconds. The set-up is up to 350 times faster than conventional X-ray fluorescence systems for elemental traces. The major components of the X-ray camera are polycapillary optics and a pn-CCD chip with an active area of 13 × 13 mm². This area is divided into 264 × 264 pixels of 48 × 48 µm². A full X-ray spectrum with a resolution of 152 eV @ 5.9 keV and a chip temperature of 246 K is recorded for each pixel. The chip has a read-out rate of 400 Hz. PY - 2011 DO - https://doi.org/10.1039/c1ja10069f SN - 0267-9477 SN - 1364-5544 VL - 26 SP - 1986 EP - 1989 PB - Royal Society of Chemistry CY - London AN - OPUS4-24386 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zier, M. A1 - Munnik, F. A1 - Reinholz, Uwe A1 - Riesemeier, Heinrich A1 - Radtke, Martin T1 - Accurate stopping power determination of 15N ions hydrogen depth profiling by a unique combination of ion beams and synchrotron radiation T2 - 20th International Conference on Ion Beam Analysis CY - Itapema, Brazil DA - 2011-04-10 PY - 2011 AN - OPUS4-23607 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scharf, O. A1 - Wedell, R. A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Riesemeier, Heinrich A1 - Langhoff, N. A1 - Soltau, H. A1 - Ihle, S. T1 - X-ray color camera, a detector with high resolution in energy and space T2 - E-MRS 2011 SPRING MEETING CY - Nice, France DA - 2011-05-09 PY - 2011 AN - OPUS4-23267 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cabral, A.R. A1 - Lehmann, B. A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Riesemeier, Heinrich A1 - Kwitko-Ribeiro, R. A1 - Tupinambá, M. T1 - Iodine fingerprints biogenic fixation of platinum and palladium T2 - Goldschmidt 2011 CY - Prague, Czech Republic DA - 2011-08-14 PY - 2011 AN - OPUS4-23606 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Radtke, Martin A1 - Buzanich, Günter A1 - Reinholz, Uwe A1 - Riesemeier, Heinrich T1 - X-ray Fluorescence analysis using synchrotron radiation excitation T2 - 75. Jahrestagung der DPG und DPG Frühjahrstagung CY - Dresden, Germany DA - 2011-03-13 PY - 2011 AN - OPUS4-24023 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Radtke, Martin T1 - First experiences with the combination of polycapillary optics and an energy dispersive pn- CCD detector at BAMline at Bessy T2 - X-ray micro-fluorescence spectroscopy at the PETRA III extension: second user workshop CY - Hamburg, Germany DA - 2011-09-27 PY - 2011 AN - OPUS4-26924 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Radtke, Martin T1 - Röntgenfluoreszenzanalyse mit Synchrotronstrahlung an der Bundesanstalt für Materialforschung und -prüfung (BAM), Berlin T2 - Seminar: "Strahlenphysikalische Anwendungen in Technik und Medizin" CY - Vienna, Austria DA - 2011-11-23 PY - 2011 AN - OPUS4-26926 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Bäßler, Ralph A1 - Otremba, Frank T1 - Use of higher-alloyed metallic materials and duplex steels for transport tanks of dangerous goods N2 - Compatibility evaluations of selected metallic materials under the influence of dangerous goods are published in the BAM-List - Requirements for Tanks for the Transport of Dangerous Goods” as basis for substance-related prototype approvals for tank Containers designed for the carriage of dangerous goods. There is a request of the tank manufacturing industry and transportation Companies to incorporate additional materials into the BAM-List, especially corrosion-resistant materials because of the large number of corrosive dangerous goods. One solution to solve corrosion Problems is to line the tank with a polymer, an alternative solution is the application of high-alloyed stainless steels and nickel-based alloys as there are 1.4529 (XINiCrMoCu 25-20-7, alloy 926), 1.4562 (X1NiCrMoCu32-28-7, alloy 31) and 2.4605 (NiCr23Mo16AI, alloy 59). There is an interest to use cost-efficient steels with high strength values and concomitant adequate corrosion resistance such as duplex steel 1.4362 (X2CrNiN23-4). This steel grade was originally developed as a substitute for the austenitic grades 1.4404 (X2CrNiMo17-12-2) and 1.4571 (X6CrNiMoTi17-12-2). Due to the lower content of the alloy elements nickel and molybdenum this duplex steel is a cost-efficient alternative to molybdenum containing austenite. Due to the limited number of corrosion test results with welded test samples of these high-alloyed materials and the duplex steel under the influence of corrosive dangerous goods a comprehensive test Programme was performed with these materials in Cooperation with ThyssenKrupp VDM and Deutsche Edelstahlwerke GmbH. It can be concluded from the test results that the superaustenitic steels 1.4529 and 1.4562 as well as the nickel-based alloy 2.4605 are a really good alternative as tank materials for the transport of dangerous goods in comparison to the lining of the tanks. The nickel-based alloy 2.4605 shows the best resistance and is suitable as material for tanks transporting all tested corrosive substances. One exception is the temperature limit during the transport of hydrochloric acid. The superaustenit 1.4562 is a resistant material with a wide ränge of application. Exceptions for use are: ammonium bifluoride, brine, 34 % calcium Chloride solution, hydrochloric acid, perchloric acid, 90 % 2-chloropropionic acid, nitrating acid with nitric acid content > 50 % and molten monochloroacetic acid. The alloy is limited suitable for allyl Chloride, aluminum Chloride, copper (II) -Chloride and ferric Chloride. The superaustenit 1.4529 showed the lowest resistance compared to the other two materials. This steel is not resistant in hydrochloric acid, perchloric acid, sodium Chlorite and sodium hypochlorite. The application is limited in the concentration ränge of aqueous Solutions of aluminum Chloride, copper (II) Chloride and ferric Chloride. Due to the reduced alloying content of the duplex steel 1.4362 (X2CrNiN23-4) compared to the austenitic CrNiMo-steels, a lower resistance especially in acidic media like formic, acetic or sulfuric acid was observed. Within the more than 7.000 substances contained in the BAM-List there is a large amount of dangerous goods such as hydrocarbons, alcohols, aldehydes, ketones, ethers, esters, and inorganic alkaline substances which have a large transport volume and do not corrode the duplex steel 1.4362 (X2CrNiN23-4). The test results are included in the actual 11th edition of the BAM-List and therefore available for the costumer. T2 - Stainless steel world conference & exhibition 2011 CY - Maastricht, The Netherlands DA - 29.11.2011 KW - Duplexstahl KW - Tankcontainer KW - Tankfahrzeuge KW - Beständigkeitsbewertung KW - BAM-Liste PY - 2011 SP - 1 EP - 12 PB - KCI Publ. AN - OPUS4-24975 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Yevtushenko, Oleksandra A1 - Carrillo Salgado, Irene T1 - Korrosionsbeständigkeit von hochlegierten Stählen für die CO2-Injektion in tiefen Aquiferfluiden T2 - GfKORR-Workshop "CCS-Technologie - Werkstofffragen prozesstechnisch lösen" CY - Frankfurt am Main, Germany DA - 2011-12-14 PY - 2011 AN - OPUS4-25120 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk A1 - Döhler, M. A1 - Mevel, L. A1 - Rücker, Werner T1 - Subspace-based Damage Detection Methods on a Prestressed Concrete Bridge T2 - EURODYN 2011, "The 8th International Conference on Structural Dynamics" CY - Leuven, Belgium DA - 2011-07-04 PY - 2011 AN - OPUS4-24579 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Döhler, M. A1 - Hille, Falk A1 - Lam, X.-B. A1 - Mevel, L. A1 - Rücker, Werner T1 - Confidence Intervals of Modal Parameters during Progressive Damage Test T2 - IMAC XXIX, "A Conference and Exposition on Structural Dynamics" CY - Jacksonville, FL, USA DA - 2011-01-31 PY - 2011 AN - OPUS4-24572 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Döhler, M. A1 - Hille, Falk A1 - Mevel, L. A1 - Rücker, Werner T1 - Structural Health Monitoring during Progressive Damage Test of S101 Bridge T2 - IWSHM 2011, "The 8th International Workshop on Structural Health Monitoring 2011" CY - Stanford, CA, USA DA - 2011-09-13 PY - 2011 AN - OPUS4-24582 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Burkert, Andreas A1 - Klapper, Helmuth Sarmiento T1 - Korrosionsuntersuchungen an hochlegierten Werkstoffen in einem künstlichen Geothermiefluid unter Betriebsbedingungen T2 - Geothermiekongress 2011 CY - Bochum, Germany DA - 2011-11-15 PY - 2011 AN - OPUS4-25222 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Döhler, M. A1 - Hille, Falk A1 - Mevel, L. A1 - Rücker, Werner T1 - Uncertainty Quantification and Risk Estimation from Key Performance Indicators T2 - IRIS Summer Academy 2011 CY - Zell am See, Austria DA - 2011-09-05 PY - 2011 AN - OPUS4-24570 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sobetzki, Joana A1 - Bäßler, Ralph A1 - Klapper, Helmuth Sarmiento T1 - Corrosion properties of high-alloyed materials in artificial geothermal fluids T2 - Eurocorr 2011 CY - Stockholm, Sweden DA - 2011-09-04 PY - 2011 AN - OPUS4-24263 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk T1 - Damage monitoring on OWT structures T2 - BAM-DTU Workshop on Design and maintenance of support structures for Offshore Wind Converters CY - Copenhagen, Denmark DA - 2011-10-25 PY - 2011 AN - OPUS4-24736 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias T1 - Large Capacity and Fatigue Testing at BAM related to Offshore Structures T2 - BAM DTU Workshop on Design and maintenance of support structures for Offshore Wind Converters CY - Copenhagen, Denmark DA - 2011-10-25 PY - 2011 AN - OPUS4-27018 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Döhler, M. A1 - Hille, Falk A1 - Mevel, L. A1 - Rücker, Werner ED - Chang, F.-K. T1 - Structural health monitoring during progressive damage test of S101 bridge N2 - For the last decades vibration based identification of damage on civil Engineering structures has become an important issue for maintenance operations on transport infrastructure. Research in that field has been rapidly expanding from classic modal Parameter estimation using measured excitation to modern operational monitoring. Here the difficulty is to regard to the specific environmental and operational influence to the structure under observation. In this paper, two methods accounting for statistical and/or operational uncertainties are applied to measurement data of a progressive damage test on a prestressed concrete bridge. On the base of covariance driven Stochastic Subspace Identification (SSI) an algorithm is developed to monitor and automatically compute confidence intervals of the obtained modal parameters. Furthermore, a null space based non-parametric damage detection method, utilizing a statistical χ2 type test is applied to the measurement data. It can be shown that for concrete bridges the proposed methodology is able to clearly indicate the presence of structural damage, if the damage leads to a change of the structural system. T2 - 8th International workshop on structural health monitoring 2011 CY - Stanford, CA, USA DA - 13.09.2011 KW - Subspace identification KW - Damage detection KW - Convidence intervals KW - Prestressed concrete bridge PY - 2011 SN - 978-1-60595-053-2 VL - 1 SP - 748 EP - 758 PB - DEStech Publications, Inc. AN - OPUS4-24688 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bettge, Dirk A1 - Ruhl, Aki Sebastian A1 - Bäßler, Ralph A1 - Yevtushenko, Oleksandra A1 - Kranzmann, Axel T1 - Corrosion aspects of materials selection for CO2 transport and storage N2 - The geological storage of carbon dioxide (Carbon Capture and Storage, CCS) in depleted gas reservoirs or in saline aquifers is a widely discussed issue. Carbon dioxide may induce corrosion on the piping steels during compression, transportation and injection. Therefore, selection of appropriate piping steels is a key factor in order to increase the safety and reliability of the CCS technology, and to keep the processes cost-effective. The here described subproject of the COORAL project (German acronym for “C02 purity for capture and storage”) deals with the levels of impurities in the C02 stream that will be acceptable when using specific steels. Material exposure to carbon dioxide (C02) containing specific amounts of water vapor, oxygen (02) sulfur dioxide (S02), nitrogen dioxide (N02), carbon monoxide (CO) can be a challenge to steels. Within this subproject 13 different Steels are tested for suitability as materials used for compression, transportation and injection Units within the CCS chain. T2 - 2nd ICEPE International conference on energy process engineering - Efficient carbon capture for coal power plants CY - Frankfurt/M., Germany DA - 20.06.2011 KW - Carbon capture KW - CCS KW - Corrosion PY - 2011 SP - 76 EP - 78 AN - OPUS4-24250 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Yevtushenko, Oleksandra A1 - Carrillo Salgado, Irene T1 - Expected corrosion behavior of highly alloyed steels during carbon dioxide injection in deep geological aquifer fluids T2 - Eurocorr 2011 CY - Stockholm, Sweden DA - 2011-09-04 PY - 2011 AN - OPUS4-24262 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Döhler, M. A1 - Hille, Falk A1 - Lam, X.-B. A1 - Mevel, L. A1 - Rücker, Werner ED - Proulx, T. T1 - Confidence intervals of modal parameters during progressive damage test N2 - In Operational Modal Analysis, the modal parameters (natural frequencies, damping ratios and mode shapes) obtained from Stochastic Subspace Identification (SSI) of a structure, are afflicted with statistical uncertainty. For evaluating the quality of the obtained results it is essential to know the respective confidence intervals of these figures. In this paper we present algorithms that automatically compute the confidence intervals of modal parameters obtained from covarianceand data-driven SSI of a structure based on vibration measurements. They are applied to the monitoring of the modal parameters of a prestressed concrete highway bridge during a progressive damage test that was accomplished within the European research project IRIS. Results of the covariance- and data-driven SSI are compared. T2 - 29th IMAC - Conference on structural dynamics CY - Jacksonville, FL, USA DA - 31.01.2011 KW - Stochastische subspace basierte Identifikation KW - Schadensdetektion KW - Spannbetonbrücke PY - 2011 SN - 978-1-4419-9304-5 DO - https://doi.org/10.1007/978-1-4419-9305-2_17 SN - 2191-5644 N1 - Serientitel: Conference Proceedings of the Society for Experimental Mechanics Series – Series title: Conference Proceedings of the Society for Experimental Mechanics Series VL - 4 SP - 237 EP - 250 PB - Springer AN - OPUS4-24335 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk A1 - Döhler, M. A1 - Mevel, L. A1 - Rücker, Werner ED - De Roeck, G. ED - Degrande, G. ED - Lombaert, G. ED - Müller, G. T1 - Subspace-based damage detection methods on a prestressed concrete bridge N2 - For the last decades vibration based damage detection of engineering structures has become an important issue for maintenance operations on transport infrastructure. Research in vibration based structural damage detection has been rapidly expanding from classic modal parameter estimation to modern operational monitoring. Methodologies from control Engineering especially of aerospace applications have been adopted and converted for the application on civil structures. Here the difficulty is to regard to the specific environmental and operational influence to the structure under observation. A null space based damage detection algorithm is tested for its sensitivity to structural damage of a prestressed concrete road bridge. Specific techniques and extensions of the algorithm are used to overcome difficulties from the size of the structure which is associated with the number of recorded sensor channels as well as from the operational disturbances by a nearby construction site. It can be shown that for concrete bridges the proposed damage detection methodology is able to clearly indicate the presence of structural damage, if the damage leads to a significant change of the structural system. Small damage which do not result in a System change when not activated by loading, do not lead to a modification of the dynamic response behavior and for that cannot be detected with the proposed global monitoring method. T2 - EURODYN 2011 - 8th International conference on structural dynamics CY - Leuven, Belgium DA - 04.07.2011 KW - Subspace methods KW - Fault detection KW - Monitoring techniques KW - Concrete bridge PY - 2011 SN - 978-90-760-1931-4 IS - MS12 TUE 11:45 SP - 2304 EP - 2310 AN - OPUS4-24689 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Matiaske, Anna-Maria A1 - Gornushkin, Igor B. A1 - Panne, Ulrich T1 - Double-pulse laser-induced breakdown spectroscopy for analysis of molten glass N2 - A mobile double-pulse laser-induced breakdown spectroscopy system for industrial environments is presented. Its capabilities as a process analytical technique for the recovery of metals from molten inorganic wastes are investigated. Using low-melting glass doped with different amounts of additives as a model system for recycling slags, the optimum number of shots, laser inter-pulse and acquisition delay times are optimized for solid and liquid (1200 °C) glass. Limits of detection from 7 ppm (Mn) to 194 ppm (Zn) are achieved working at a distance of 75 cm from the sample. To simplify the quantification of molten samples in an industrial furnace, the possibility is examined of using solid standards for analysis of molten material. KW - Laser-induced breakdown spectroscopy KW - LIBS KW - Double-pulse LIBS KW - Molten glass KW - Recycling PY - 2011 DO - https://doi.org/10.1007/s00216-011-5165-2 SN - 1618-2642 SN - 1618-2650 VL - 402 IS - 8 SP - 2597 EP - 2606 PB - Springer CY - Berlin AN - OPUS4-23950 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maierhofer, Christiane A1 - Ziegler, Mathias A1 - Kunert, M. A1 - Goldammer, M. T1 - Entwicklung von Referenzprobekörpern für die Standardisierung der Blitzthermografie N2 - Die aktive Thermografie wird in der Industrie zunehmend in verschiedenen Bereichen zur Qualitätssicherung, Zustandsdiagnose und Zustandsüberwachung eingesetzt. Bestehende Normen zur Thermografie beschreiben die Grundlagen, Geräte und Begriffe. In diesem Beitrag wird über ein Projekt berichtet, dessen Ziel die Erarbeitung einer Prüfnorm zur Blitzthermografie ist. Diese sollte neben der Auswahl geeigneter Gerätekomponenten, der Auswertungsverfahren und der Vorgehensweise bei der Prüfung auch die Beschreibung geeigneter Referenzprobekörper enthalten, die eine Bewertung der Messapparatur und eine Qualitätssicherung der Prüfung ermöglichen. T2 - Thermographie-Kolloquium 2011 CY - Stuttgart, Germany DA - 29.09.2011 KW - Aktive Thermografie KW - Blitzanregung KW - Prüfnorm KW - Referenzprobekörper PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-246230 SN - 978-3-940283-36-8 VL - 130 SP - 1 EP - 7 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-24623 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlichting, Joachim A1 - Ziegler, Mathias A1 - Pelkner, Matthias A1 - Maierhofer, Christiane A1 - Kreutzbruck, Marc T1 - Kameragestütztes Flying-Spot-Verfahren zur Risserkennung N2 - In dieser Arbeit wird ein kameragestütztes Verfahren zur Flying- Spot-Thermografie vorgestellt. Die Anregung wird über einen Diodenlaser mit einem optischen Scanner realisiert. Bei der Auswertung kommt ein effizienter und robuster Algorithmus zum Einsatz, der direkt auf die mit der Kamera aufgenommene Thermografiesequenz angewendet werden kann, ohne auf eine Synchronisation zwischen Kamera und Lasersystem angewiesen zu sein. Daher eignet sich diese Herangehensweise besonders zur Nachrüstung bestehender Thermografiesysteme. Die prinzipielle Eignung dieser Methode wird anhand einer Messung an einem Schienenstück mit Rollkontaktermüdungsrissen gezeigt. Als Referenzverfahren werden die Magnetpulverprüfung und eine auf GMR (Giant Magnetoresistance)- Sensoren basierende Streufeldmessung herangezogen. Mit dem thermografischen Verfahren konnten sämtliche enthaltenen Fehler erkannt werden. Dabei wurden Risse im mm-Abstand getrennt nachgewiesen, was etwa der geometrischen Auflösung der eingesetzten Kamera entspricht. T2 - Thermographie-Kolloquium 2011 CY - Stuttgart, Germany DA - 29.09.2011 KW - Flying-Spot Thermografie KW - Diodenlaser KW - Rissortung KW - Magnetpulverprüfung KW - GMR-Sensoren PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-246220 SN - 978-3-940283-36-8 IS - DGZfP-BB 130 (Vortrag 09) SP - 1 EP - 6 PB - Deutsche Gesellschaft für zerstörungsfreie Prüfung e.V. (DGZfP) AN - OPUS4-24622 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Meggyes, Tamás T1 - Effective cleanup of groundwater contaminated with uranium using permeable reactive barriers T2 - 4th International contaminated site remediation conference - CleanUp 2011 CY - Adelaide, Australia DA - 2011-09-11 KW - Permeable reactive barriers KW - Groundwater remediation KW - Uranium PY - 2011 SN - 978-1-921431-29-6 IS - A 106 SP - 13 EP - 14 AN - OPUS4-25558 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Brenneis, Rudolf A1 - Adamczyk, Burkart A1 - Simon, Franz-Georg T1 - Recycling of Waste Materials by Thermochemical Treatment T2 - International Conference Environmental (Bio) Technologies & EU-FP7 Environment Brokerage Event CY - Gdansk, Poland DA - 2011-09-05 PY - 2011 AN - OPUS4-24326 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Rohstoffpotenzial von MVA Schlackedeponien T2 - Gemeinschaftstagung von ANS, VKU und DWA Deponietage CY - Neuss, Germany DA - 2011-11-22 PY - 2011 AN - OPUS4-25015 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Berger, Wolfgang T1 - Recovery of scarce metals from end-of-life photovoltaic modules T2 - Resources that don’t cost the earth - workshop CY - Berlin, Germany DA - 2011-12-01 KW - Resources KW - Photovoltaics KW - Recycling PY - 2011 IS - Case study 3 SP - 18 PB - RSC AN - OPUS4-26834 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tomm, J.W. A1 - Ziegler, Mathias A1 - Hempel, M. A1 - Elsaesser, T. T1 - Mechanisms and fast kinetics of the catastrophic optical damage (COD) in GaAs-based diode lasers N2 - COD diagram determined for a batch of broad-area AlGaAs diode lasers. The time to COD within a single current pulse is plotted versus the actual average optical power in the moment when the COD takes place. Full circles stand for clearly identified COD events (right ordinate), whereas open circles (left ordinate) represent the pulse duration in experiments, where no COD has been detected. A borderline (gray) exists between two regions, i. e., parameter sets, of presence (orange) and absence of COD (blue). This borderline is somewhat blurred because of the randomness in filamentation of the laser nearfield and scatter in properties of the involved individual devices. KW - Semiconductor laser KW - Thermography KW - Catastrophic optical damage KW - High-power diode lasers KW - Destructive testing KW - Non-destructive testing PY - 2011 DO - https://doi.org/10.1002/lpor.201000023 SN - 1863-8880 VL - 5 IS - 3 SP - 422 EP - 441 PB - Wiley-VCH CY - Weinheim AN - OPUS4-23624 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schlichting, Joachim A1 - Ziegler, Mathias A1 - Dey, Anika A1 - Maierhofer, Christiane A1 - Kreutzbruck, Marc T1 - Efficient data evaluation for thermographic crack detection N2 - We present an all-purpose crack detection algorithm for flying spot thermography which is directly applicable to a thermogram sequence without the need of any additional information about the experimental setup. A single image containing distinct crack signatures is derived in two steps. Firstly, the spatial derivative is calculated for each frame of the sequence and, secondly, the resulting data set is sorted pixel wise along the time axis. The feasibility of the proposed procedure is proven by testing a piece of rail that comprises roll contact fatigue cracks and by comparing the results with magnetic particle testing. KW - Active thermography KW - Laser scanner KW - Railway KW - Roll contact fatigue KW - Open surface cracks PY - 2011 SN - 1768-6733 VL - 8 IS - 1 SP - 119 EP - 123 PB - Lavoisier CY - Cachan Cedex AN - OPUS4-24255 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pagano, R. A1 - Ziegler, Mathias A1 - Tomm, J.W. A1 - Esquivias, I. A1 - Tijero, J.M.G. A1 - O'Callaghan, J.R. A1 - Michel, N. A1 - Krakowski, M. A1 - Corbett, B. T1 - Two-dimensional carrier density distribution inside a high power tapered laser diode N2 - The spontaneous emission of a GaAs-based tapered laser diode emitting at λ = 1060 nm was measured through a window in the transparent substrate in order to study the carrier density distribution inside the device. It is shown that the tapered geometry is responsible for nonuniform amplification of the spontaneous/stimulated emission which in turn influences the spatial distribution of the carriers starting from below threshold. The carrier density does not clamp at the lasing threshold and above it the device shows lateral spatial hole-burning caused by high stimulated emission along the cavity center. KW - Carrier density KW - Gallium arsenide KW - III-V semiconductors KW - Indium compounds KW - Laser cavity resonators KW - Optical hole burning KW - Quantum well lasers KW - Stimulated emission KW - Superradiance PY - 2011 DO - https://doi.org/10.1063/1.3596445 SN - 0003-6951 SN - 1077-3118 VL - 98 SP - 221110-1 EP - 221110-3 PB - American Institute of Physics CY - Melville, NY AN - OPUS4-23873 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maierhofer, Christiane A1 - Röllig, Mathias A1 - Steinfurth, Henrik A1 - Ziegler, Mathias A1 - Heck, S.J. A1 - Scheuerlein, C. T1 - Aktive Thermografie zur zerstörungsfreien Prüfung von Lötverbindungen N2 - In diesem Beitrag werden die Möglichkeiten der Ortung von Fehlstellen in Cu Lötverbindungen unterhalb verschiedener Cu Blechdicken mit aktiver Thermografie demonstriert. Dabei wurden die Anregung mit Blitzlicht und die periodische Anregung mit der Lock-In Technik miteinander verglichen. Die Vor- und Nachteile der Anwendung unterschiedlicher IR-Kamerasysteme, einer gekühlten InSb-Quantendetektor IR-Kamera und einer Mikrobolometer IR-Kamera, werden dargestellt. Als objektives Kriterium wurde das SNR für unterschiedliche Fehlstellengrößen herangezogen. T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 30.05.2011 KW - Aktive Thermografie KW - Blitzlichtanregung KW - Lock-In Anregung KW - Lötverbindung KW - Kupfer PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-249935 SN - 978-3-940283-33-7 IS - DGZfP-BB 127 (Di.1.C.1) SP - 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-24993 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maierhofer, Christiane A1 - Doroshtnasir, Manoucher A1 - Steinfurth, Henrik A1 - Ziegler, Mathias A1 - Kreutzbruck, Marc A1 - Scheuerlein, C. A1 - Heck, S. J. T1 - Comparison of different infrared camera systems and excitation strategies for testing of solder connections T2 - 11th International Workshop on Advanced Infrared Technology and Applications CY - L'Aquila, Italy DA - 2011-09-07 PY - 2011 AN - OPUS4-24432 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ziegler, Mathias A1 - Hempel, M. A1 - Tomm, J.W. A1 - Elsaesser, T. A1 - Michel, N. A1 - Krakowski, M. T1 - Catastrophic optical damage at front and rear facets of 975 nm emitting diode lasers T2 - CLEO, Conference on Lasers and Electro-Optics CY - Baltimore, MD, USA DA - 2011-05-03 PY - 2011 AN - OPUS4-23785 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maierhofer, Christiane A1 - Röllig, Mathias A1 - Steinfurth, Henrik A1 - Ziegler, Mathias A1 - Heck, S. J. A1 - Scheuerlein, C. T1 - Aktive Thermografie zur zerstörungsfreien Prüfung von Lötverbidungen T2 - DGZfP-Jahrestagung 2011 CY - Bremen, Germany DA - 2011-05-30 PY - 2011 AN - OPUS4-23903 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ziegler, Mathias A1 - Schlichting, Joachim A1 - Maierhofer, Christiane A1 - Pelkner, Matthias A1 - Kreutzbruck, Marc T1 - Kameragestütztes Flying-Spot-Verfahren zur Risserkennung T2 - Thermografie-Kolloquium 2011 CY - Stuttgart, Germany DA - 2011-09-29 PY - 2011 AN - OPUS4-24542 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maierhofer, Christiane A1 - Ziegler, Mathias A1 - Kunert, M. A1 - Goldammer, M. T1 - Entwicklung von Referenzprobekörpern für die Standardisierung der Blitzthermografie T2 - Thermografie Kolloquium 2011 CY - Stuttgart, Germany DA - 2011-09-29 PY - 2011 AN - OPUS4-24548 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Guilherme, A. A1 - Buzanich, Günter A1 - Lühl, Lars A1 - Wolff, Timo A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - dos Santos, J.F. A1 - Kanngießer, B. A1 - Coroado, J. A1 - Carvalho, M.L. T1 - SR.-XANES for the Study of Portuguese Polychrome Glazed Ceramics: 16th - 19th centuries T2 - TECHNART 2011, Non-destructive and microanalytical techniques in art and cultural heritage CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-24148 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Guilherme, A. A1 - Buzanich, Günter A1 - Wolff, Timo A1 - Lühl, L. A1 - Corado, J. A1 - dos Santos, J.F. A1 - Kanngießer, B. A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Carvalho, M.L. T1 - SR-Xanes for the study of portuguese polychrome glazed ceramics: 16th - 19th centuries T2 - Technart 2011 CY - Berlin, Germany DA - 2011-04-26 PY - 2011 AN - OPUS4-23083 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Wu, Guang Mei T1 - Quantitative Assessment and Optimization of Flame Retardancy by the Shielding Effect in Epoxy Nanocomposites N2 - Diese Arbeit trägt zum halogenfreien Flammschutz von Epoxidharzen durch Nanokomposite mit Phosphonium modifiziertem Schichtsilikat bei. Der Flammschutz resultiert aus der während der Pyrolyse entstehenden inorganisch-organischen Schutzschicht. Diese Brandrückstandsschicht wirkt als Hitzeschild für das darunterliegende Material. Ziel dieser Arbeit ist die experimentelle und quantitative Beschreibung dieses Effekts und die Optimierung der Flammschutzwirkung. Die während der erzwungenen Verbrennung im Cone Calorimeter auftretenden Wärmeflüsse und Materialoberflächentemperaturen wurden in selbst konzipierten Experimenten bestimmt. Der durch die Schutzschicht zurückgestrahlte Wärmefluß und die daraus resultierte Reduktion des in der Pyrolysezone effektiv in Brennstofffreisetzung umgesetzten Wärmeflusses wurden erfolgreich quantifiziert. Mit diesem effektiven Wärmefluß nahmen wichtige Brandeigenschaften wie die Wärmefreisetzungsrate ab. Zur Optimierung der Schutzschicht wurde drei Ansätze verfolgt: Variation der organischen Modifizierung, verbesserte Dispersion durch den Einsatz von interkaliertem Triphenylphosphat und die Optimierung der Morphologie der Schutzschicht durch die Kombination von Schichtsilikat mit niedrig schmelzenden Gläsern. Durch den Einsatz verschiedener organischer Kationen lässt sich die Verteilung der Nanopartikel, die Struktur der Schutzschicht und damit die Flammschutzwirkung optimieren. Obwohl die Interkalation von Triphenylphosphat eine deutliche Aufweitung der Schichtabstände im Schichtsilikat bewirkt, zeigen die entsprechenden Nanokomposite keine verbesserte Verteilung der Partikel, keine homogenere Schutzschicht und keine Erhöhung der Flammschutzwirkung im Vergleich zu analogen Mischsystemen, in denen additiv Triphenylphosphat zugegeben wurde. Die Kombination von organisch modifiziertem Schichtsilikat und niedrig schmelzenden Gläsern zeigen in den meisten der untersuchten Systeme antagonistische Effekte. Nur in wenigen Kombinationen ist, die Superposition bzw. sogar eine Synergie zwischen den Flammschutzeffekten beider Zusätze zu beobachten. Die erstmalige experimentelle Quantifizierung des Hitzeschildes in Polymernanokompositen ist ein wertvoller Beitrag für ein grundlegendes Verständnis der Flammschutzmechanismen in Nanokompositen. Die Abhängigkeit der Flammschutzwirkung von der Struktur der Schutzschicht wurde nachgewiesen. Zur Optimierung der Schutzschichtstruktur und damit des Flammschutzes wurden drei Ansätze vorgeschlagen. N2 - The motivation of this study was to pursue effective eco-friendly and economical flame retarded polymer materials. With wide-ranging advantages such as improved fire and physical properties, halogen-free and relatively low cost, layered silicate / epoxy nanocomposite (EP_LS) was targeted for high efficiency of flame retardancy. One main goal of this study was to increase the understanding of the flame retardancy phenomenon in EP_LS by assessing the shielding effect of the protection layer experimentally and quantitatively. Another main goal of this study was to optimize the flame retardancy by the shielding effect in EP_LS. T3 - BAM Dissertationsreihe - 77 KW - Flame retardancy KW - Shielding effect KW - Nanocomposite KW - Layered silicate KW - Low-melting glass PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-816 SN - 978-3-9814281-7-9 SN - 1613-4249 VL - 77 SP - 1 EP - 125 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-81 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vogel, Christian A1 - Adam, Christian A1 - Unger, M. T1 - Heavy metal removal from sewage sludge ash analyzed by thermogravimetry N2 - A high temperature (1000 °C) thermochemical process for heavy metal removal from sewage sludge ash via the chloride pathway was investigated by thermogravimetry/differential thermal analysis (TG/DTA). TG and DTA measurements gave information about secession and evaporation of water, HCl, and heavy metal chlorides at different temperatures. Additionally, gaseous water and hydrochloric acid which occurred in the process were detected by an FT-IR detector that was coupled to the TG/DTA-system. Heavy metal chlorides which were also formed in the process cannot be detected by this technique. For that reason the outlet gas of the TG/DTA-system was discharged into washing flasks filled with water for absorption. The washing flasks were replaced in temperature steps of 50 °C and the heavy metal concentrations of the solutions were determined by ICP-OES. The temperature-dependent formation/evaporation of different heavy metal chlorides was analyzed and compared for two different thermochemical processes using magnesium chloride hydrate or calcium chloride hydrate as Cl-donors. In both cases evaporation of Cd, Cu, Pb, and Zn was observed from 600 °C, whereas As, Cr, and Ni remained in the solid state. The results were discussed against the background of thermodynamic calculations. KW - Sewage sludge ash KW - Heavy metal chloride KW - Thermodynamic simulation KW - Thermogravimetry/FT-IR PY - 2011 DO - https://doi.org/10.1007/s10973-010-0966-7 SN - 1388-6150 SN - 1418-2874 SN - 0368-4466 SN - 1572-8943 VL - 103 SP - 243 EP - 248 PB - Kluwer Academic Publ. CY - Dordrecht AN - OPUS4-23157 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vogel, Christian A1 - Kohl, Anka A1 - Adam, Christian T1 - Spectroscopic investigation in the mid- and far-infrared regions of phosphorus fertilizers derived from thermochemically treated sewage sludge ash N2 - Inorganic phosphorus and nitrogen-phosphorus-potassium (NPK) fertilizers based on phosphates from thermochemically treated sewage sludge ash were analyzed using mid-infrared (mid-IR) and far-infrared (FIR) spectroscopy. The different compounds present in the fertilizers were qualitatively determined with the help of recorded reference spectra of pure substances. Differentiation between various phosphates and other compounds such as sulfates, nitrates, and oxides was possible using combined interpretation of the mid-IR and FIR spectra. The results are in agreement with previous X-ray diffraction (XRD) measurements of the same samples. The main phosphate phases detected were NH4H2PO4, MgHPO4·3H2O, Mg3(PO4)2, Ca5(PO4)5Cl, CaHPO4·2H2O, Ca(H2-PO4)2·H2O, and AlPO4. Furthermore, K2SO4, NH4NO3, Fe2O3, and SiO2 were identified in the IR spectra. However, ammonium and sulfate compounds were only identified in the mid-IR region but were not detectable in the FIR region. KW - Sewage sludge ash KW - Fertilizer KW - P-fertilizer KW - Phosphorus compounds KW - Mid-infrared spectroscopy KW - Far-infrared spectroscopy PY - 2011 DO - https://doi.org/10.1366/10-06168 SN - 0003-7028 SN - 1943-3530 VL - 65 IS - 3 SP - 265 EP - 271 PB - Society for Applied Spectroscopy CY - Frederick, Md. AN - OPUS4-23270 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vogel, Christian A1 - Adam, Christian T1 - Heavy metal removal from sewage sludge ash by thermochemical treatment with gaseous hydrochlorid acid N2 - Sewage sludge ash (SSA) is a suitable raw material for fertilizers due to its high phosphorus (P) content. However, heavy metals must be removed before agricultural application and P should be transferred into a bioavailable form. The utilization of gaseous hydrochloric acid for thermochemical heavy metal removal from SSA at approximately 1000 °C was investigated and compared to the utilization of alkaline earth metal chlorides. The heavy metal removal efficiency increased as expected with higher gas concentration, longer retention time and higher temperature. Equivalent heavy metal removal efficiency were achieved with these different Cl-donors under comparable conditions (150 g Cl/kg SSA, 1000 °C). In contrast, the bioavailability of the P-bearing compounds present in the SSA after thermal treatment with gaseous HCl was not as good as the bioavailability of the P-bearing compounds formed by the utilization of magnesium chloride. This disadvantage was overcome by mixing MgCO3 as an Mg-donor to the SSA before thermochemical treatment with the gaseous Cl-donor. A test series under systematic variation of the operational parameters showed that copper removal is more depending on the retention time than the removal of zinc. Zn-removal was declined by a decreasing ratio of the partial pressures of ZnCl2 and water. KW - Phosphorus recycling KW - Sewage sludge ash KW - Heavy metal elimination KW - Urban mining PY - 2011 DO - https://doi.org/10.1021/es2007319 SN - 0013-936X SN - 1520-5851 VL - 45 IS - 17 SP - 7445 EP - 7450 PB - ACS Publ. CY - Washington, DC AN - OPUS4-24170 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Peplinski, Burkhard A1 - Adam, Christian A1 - Reuther, H. A1 - Vogel, Christian A1 - Adamczyk, Burkart A1 - Menzel, Michael A1 - Emmerling, Franziska A1 - Simon, Franz-Georg T1 - First identification of the tridymite form of AlPO4 in municipal sewage sludge ash N2 - Sewage sludge and sewage sludge ashes (SSA) are produced in huge amounts at municipal waste water treatment plants (WWTP) all around the world and have become an issue for many urbanized areas. To deal with this unceasing mass flow in an ecologically and economically responsible way a comprehensive chemical and structural characterization of all types of SSA is needed. X-ray powder diffraction (XRD) is one of the most promising analytical methods for this task. Although, there has been ample chemical evidence showing that many SSA contain aluminium phosphate as a major component up to now no aluminium phosphate or aluminium-rich mixed phosphate phase has been reported to be identified by XRD in a SSA produced at a mono-incineration facility. The outcome of the present com-bined XRD and Mossbauer spectroscopy investigation provides comprehensive evidence closing this gap for the first time. KW - Aluminium phosphate KW - AlPO4 KW - Tridymite KW - Sewage sludge ash KW - Incinerator KW - Ash PY - 2011 DO - https://doi.org/10.1524/zkpr.2011.0067 SN - 0044-2968 VL - 1 SP - 443 EP - 448 PB - Oldenbourg CY - München AN - OPUS4-24297 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Suhendra, Suhendra A1 - Vogel, Christian A1 - Adam, Christian T1 - Granulation of sewage sludge ashes, biomass ashes and industrial by-product for sustainable production of multinutrient fertilizer T2 - European Congress of Chemical engineering, together with ProcessNet Annual Meeting CY - Berlin, Germany DA - 2011-09-25 PY - 2011 AN - OPUS4-24398 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppl, T. A1 - Altstädt, V. A1 - Ciesielski, M. A1 - Bykov, Y. A1 - Döring, M. A1 - Fischer, O. A1 - Pospiech, D. A1 - Brehme, Sven A1 - Schartel, Bernhard T1 - Influence of solid and polymeric halogen-free flame retardants on the structure-property relationships of Poly(Butylene Terephthalate) T2 - 13th European Meeting on Fire Retardant Polymers, FRPM CY - Alessandria, Italy DA - 2011-06-26 PY - 2011 AN - OPUS4-24074 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pospiech, D. A1 - Fischer, O. A1 - Korwitz, A. A1 - Starke, S. A1 - Häußler, L. A1 - Kretzschmar, B. A1 - Ciesielski, M. A1 - Brehme, Sven A1 - Schartel, Bernhard T1 - Copolyesters with DOPO building blocks as successful flame retardant additives in Poly(Butylene Terephthalate) T2 - 13th European Meeting on Fire Retardant Polymers, FRPM CY - Alessandria, Italy DA - 2011-06-26 PY - 2011 AN - OPUS4-24071 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmid, C. A1 - Falkenhagen, Jana A1 - Barner-Kowollik, C. T1 - Switching from raft to rop: A facile route to complex and sulfur-free macromolecular architectures T2 - 11th Annual UNESCO/IUPAC Workshop and Conference on Functional Polymeric Materials and Composites CY - Stellenbosch, South Africa DA - 2011-04-27 PY - 2011 AN - OPUS4-23981 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Despinasse, Marie-Claire A1 - Schartel, Bernhard T1 - Arylphosphates and phosphazene flame retardants in Polycarbonate / Acrylonitrile-Butadiene-Styrene blends T2 - 13th European Meeting on Fire Retardant Polymers, FRPM CY - Alessandria, Italy DA - 2011-06-26 PY - 2011 AN - OPUS4-24068 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fischer, O. A1 - Pospiech, D. A1 - Korwitz, A. A1 - Komber, H. A1 - Sahre, K. A1 - Häußler, L. A1 - Bykov, Y. A1 - Brehme, Sven A1 - Schartel, Bernhard T1 - Comparative study on Polyesters with systematically altered Phosphorus containing side groups T2 - 13th European Meeting on Fire Retardant Polymers, FRPM CY - Alessandria, Italy DA - 2011-06-26 PY - 2011 AN - OPUS4-24070 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, P. A1 - Ciesielski, M. A1 - Bykov, Y. A1 - Döring, M. A1 - Krämer, J. A1 - Altstädt, V. A1 - Perret, Birgit A1 - Schartel, Bernhard T1 - Phosphorous containing flame retardant additives via MICHAEL-Addition to acrylates T2 - 13th European Meeting on Fire Retardant Polymers, FRPM CY - Alessandria, Italy DA - 2011-06-26 PY - 2011 AN - OPUS4-24073 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hörold, Andreas A1 - Schartel, Bernhard A1 - Trappe, Volker A1 - Korzen, Manfred A1 - Hofmann-Böllinghaus, Anja T1 - Structural integrity of composites in fire: An intermediate-scale approach T2 - 13th European Meeting on Fire Retardant Polymers, FRPM CY - Alessandria, Italy DA - 2011-06-26 PY - 2011 AN - OPUS4-24072 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Composites and Fire: A Journey from 1 nm to 50 cm T2 - 13th European Meeting on Fire retardant Polymers, FRPM CY - Alessandria, Italy DA - 2011-06-26 PY - 2011 AN - OPUS4-24069 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yu, D. A1 - Kleemeier, M. A1 - Wu, Guang Mei A1 - Schartel, Bernhard A1 - Liu, W.Q. A1 - Hartwig, A. T1 - Phosphorus and silicon containing low-melting organic-inorganic glasses improve flame retardancy of epoxy/clay composites N2 - New low-melting organic–inorganic glassy polymers containing phosphorus and silicon are synthesized by the reaction between phenylphosphonic acid and methyltrichlorosilane or methyltriethoxysilane. They possess both low-softening points and high onset decomposition temperatures, which are favorable for preparing flame retardant composites. Although the glass by itself is sensitive to water, the composites are not significantly affected in that way. For glass/clay/epoxy composites glass transition temperature (Tg) as well as storage modulus increase with the glass amount. The glasses improve flame retardancy significantly due to flame inhibition and the formation of fire residue working as protection layer during burning. The total heat evolved is reduced by 23–28% for using 5–15 wt.% glass and the maximum HRR even by 58–48%. The latter effect decreases with increasing glass amount due to an adulterate residue deformation. The combination of glass and clay is proposed as a possible route to enhance flame retardancy. KW - Clay KW - Epoxy resin KW - Flame retardancy KW - Organic-inorganic polymer KW - Low-melting glass PY - 2011 DO - https://doi.org/10.1002/mame.201100014 SN - 1438-7492 SN - 1439-2054 VL - 296 IS - 10 SP - 952 EP - 964 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-24516 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yu, D. A1 - Kleemeier, M. A1 - Wu, Guang Mei A1 - Schartel, Bernhard A1 - Liu, W.Q. A1 - Hartwig, A. T1 - The absence of size- dependency in flame retarded composites containing low-melting organic-inorganic glass and clay: Comparison between micro- and nanocomposites N2 - Due to optimised processing of epoxy based composite materials containing a low-melting organic–inorganic glass together with an organo clay, the size of the glass particles could be successfully reduced. Thus truly nano-dispersed composites were obtained, with glass particles in the range of 10 nm to 200 nm. The small particle size allowed efficient interaction of glass particles and organo clay layers. The flame retardancy as well as the thermo-mechanical properties were tested, and the results showed that the low-melting glass led to a remarkable reduction of peak heat release rate by forming an enhanced barrier layer. Nevertheless no further improvement could be achieved by lowering the particle size to the nanometre region. For good flame retardancy a microdispersion of the low-melting glass was already sufficient. KW - Epoxy resin KW - Nanocomposites KW - Low-melting glass KW - Clay KW - Flame retardancy PY - 2011 DO - https://doi.org/10.1016/j.polymdegradstab.2011.06.003 SN - 0141-3910 SN - 1873-2321 VL - 96 IS - 9 SP - 1616 EP - 1624 PB - Elsevier Ltd. CY - London AN - OPUS4-24211 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Brehme, Sven A1 - Schartel, Bernhard A1 - Bykov, Y. A1 - Ciesielski, M. A1 - Döring, M. A1 - Fischer, O. A1 - Pospiech, D. A1 - Köppl, T. A1 - Altstädt, V. T1 - Flame retardancy mechanisms and performance of a halogen-free phosphorus polyester in PBT N2 - PET-P-DOPO is a phosphorus-containing polyester prepared from the glycol ether of the hydroquinone derivative of 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) and dimethyl terephthalate. PET-P-DOPO and a blend of PBT with PET-PDOPO were investigated with respect to pyrolysis and fire behavior. PET-P-DOPO achieves a V-0 rating in the UL 94 test and exhibits a high LOI of 39.3%. The outstanding flame-retardant properties of PET-P-DOPO are the result of three different mechanisms (flame inhibition, charring and a protection effect of the intumescent char) that are active in PET-P-DOPO. The fire load and the peak of heat release rate (pHRR) are reduced to 34% and 17%, respectively. The char exhibits an intumescent multicellular structure enabling it to act as an efficient protection layer. As PET-P-DOPO is immiscible with PBT, the blend shows a lower breaking elongation than pure PBT. Compared to pure PET-P-DOPO, the flame retardancy of the blend is decreased according to the fraction of PET-P-DOPO used. Nevertheless, the flame-retardancy of PET-P-DOPO in the blend was good enough to compete with PBT flame-retarded by AlPi-Et (aluminum diethylphosphinate) that was used as a Benchmark. KW - PBT KW - DOPO KW - Flame retardancy PY - 2011 SN - 1-59623-795-3 SP - 1 EP - 15 CY - Wellesley, USA AN - OPUS4-24617 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gallo, Emanuela A1 - Fan, Z. A1 - Schartel, Bernhard A1 - Greiner, A. T1 - Electrospun nanofiber mats coating - new route to flame retardancy N2 - A novel route toward halogen-free fire retardancy of polymers through innovative surface coating is described. Nanofiber mats based on polyimide are deposited on PA66 through electrospinning. Scanning electron microscopy is used to characterize the nanofibers. Cone calorimeter tests were performed to evaluate the fire performance. Because of their low thermal conductivity, electrospun nanofiber mats act not only as sacrificial layers but also as a protective surface that delays ignition. The effect is influenced by the fiber diameters and the imidization. KW - Electrospinning KW - Polyimide KW - Nanofibers KW - Fire retardancy PY - 2011 DO - https://doi.org/10.1002/pat.1994 SN - 1042-7147 SN - 1099-1581 VL - 22 IS - 7 SP - 1205 EP - 1210 PB - John Wiley & Sons, Ltd. CY - Chichester AN - OPUS4-24093 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yu, D. A1 - Liu, W.Q. A1 - Kleemeier, M. A1 - Hartwig, A. A1 - Wu, Guang Mei A1 - Schartel, Bernhard T1 - Improvement in Flame Retardancy of Epoxy/Clay Composites by Using Low Melting Organic-Inorganic Glasses T2 - 2nd International Conference on Flame Retardants: Chinese and International Markets Requirements, Challenges and Innovations CY - Guangzhou, China DA - 2011-05-15 PY - 2011 AN - OPUS4-24676 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bykov, Y. A1 - Ciesielski, M. A1 - Walter, O. A1 - Döring, M. A1 - Fischer, O. A1 - Köppl, T. A1 - Altstädt, V. A1 - Brehme, Sven A1 - Schartel, Bernhard T1 - Synthesis of new functionalised phosphorus-containing monomers as flame retardants for polyesters T2 - 13th European Meeting on Fire Retardant Polymers, FRPM CY - Alessandria, Italy DA - 2011-06-26 PY - 2011 AN - OPUS4-24075 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wawrzyn, Eliza A1 - Schartel, Bernhard A1 - Ciesielski, M. A1 - Döring, M. A1 - Kretzschmar, B. T1 - Are novel aryl phospates competitors for BDP in halogen-free flame retarded PC/ABS/PTFE blend? T2 - Polymers for Advanced Technologies 2011 CY - Lodz, Poland DA - 2011-10-02 PY - 2011 AN - OPUS4-24439 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Simone A1 - Raspe, Tina A1 - Deubel, Jan A1 - Piechotta, Christian A1 - Fettig, Ina A1 - Seeger, Stefan A1 - Rothhardt, Monika A1 - Schartel, Bernhard T1 - Chemische Brandspurenanalytik T2 - BAM Kolloquium CY - Berlin, Germany DA - 2011-11-09 PY - 2011 AN - OPUS4-24709 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Gezielte Entwicklung flammgeschützter Polymerwerkstoffe T2 - 11. Schwarzheider Kunststoffkolloquium CY - Schwarzheide, Germany DA - 2011-09-21 PY - 2011 AN - OPUS4-24651 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübert, Thomas A1 - Shabir Mahr, Muhammad A1 - Bahr, Horst A1 - Schartel, Bernhard T1 - Flame retardant SiO2 and TiO2 wood composites T2 - 16th International Sol-Gel Conference CY - Hangzhou, China DA - 2011-08-28 PY - 2011 AN - OPUS4-28814 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Perret, Birgit A1 - Schartel, Bernhard A1 - Stöß, K. A1 - Ciesielski, M. A1 - Diederichs, J. A1 - Döring, M. A1 - Krämer, J. A1 - Altstädt, V. T1 - Novel DOPO-based flame retardants in high-performance carbon fibre epoxy composites for aviation N2 - Two novel, halogen-free, phosphorus-based oligomeric flame retardants are investigated in the commercial epoxy resin RTM6 and ~70 wt.% carbon fibre RTM6 composites (RTM6-CF) with respect to pyrolysis and fire behaviour. The flame retardants are based on 9,10-dihydro-9-oxy-10-phosphaphenanthrene-10-oxide (DOPO) units linked to the star-shaped aliphatic ground body tetra-[(acryloyloxy)ethyl] pentarythrit (DOPP), or heterocyclic tris-[(acryloyloxy)ethyl] isocyanurate (DOPI), respectively. The glass transition temperature is reduced by adding DOPP and DOPI, but the mechanical properties of the composites (e.g. interlaminar shear strength (ILSS) and Gc in mode I and II) remain unchanged. Decomposition models are proposed based on mass loss, evolved gas analysis (TG–FTIR) and condensed product analysis (hot stage cell within FTIR). The fire behaviour is investigated comprehensively (UL 94, limiting oxygen index (LOI) and cone calorimeter). Both flame retardants act in the gas phase through flame inhibition and in the condensed phase through charring. The UL 94 of RTM6 is improved from HB to V-1 and V-0; the LOI from 25% to 34–38%. Peak heat release rate (PHRR) and total heat evolved (THE) are lowered by 31-49% and 40–44%, respectively. Adding CF increases the residue, reduces the THE, but suppresses the charring due to RTM6 and flame retardants. Thus the THE of RTM6-CF is reduced by about 25% when DOPI and DOPP are added. However, UL 94: V-0 and LOI of 45% and 48% are achieved with ~0.6 wt.% phosphorus. KW - Epoxy resin (RTM6) KW - DOPO KW - Carbon fibre reinforced composites KW - Mechanical properties KW - Flame retardancy PY - 2011 DO - https://doi.org/10.1016/j.eurpolymj.2011.02.008 SN - 0014-3057 SN - 1873-1945 VL - 47 IS - 5 SP - 1081 EP - 1089 PB - Elsevier Ltd. CY - Oxford AN - OPUS4-23548 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schartel, Bernhard A1 - Weiß, André A1 - Sturm, Heinz A1 - Kleemeier, M. A1 - Hartwig, A. A1 - Vogt, C. A1 - Fischer, R.X. T1 - Layered silicate epoxy nanocomposites: formation of the inorganic-carbonaceous fire protection layer N2 - The layered silicate (LS) modification and processing parameters applied control the morphology of the LS/polymer composites. Here, increasing the surface area of the LS particles by using alternative drying processes increases dispersion towards a more typical nanocomposite morphology, which is a basic requirement for promising flame retardancy. Nevertheless, the morphology at room temperature does not act itself with respect to flame retardancy, but serves as a prerequisite for the formation of an efficient surface protection layer during pyrolysis. The formation of this residue layer was addressed experimentally for the actual pyrolysis region of a burning nanocomposite and thus our results are valid without any assumptions or compromises on the time period, dimension, surrounding atmosphere or temperature. The formation of the inorganic-carbonaceous residue is influenced by bubbling, migration, reorientation, agglomeration, ablation, and perhaps also delamination induced thermally and by decomposition, whereas true sintering of the inorganic particles was ruled out as an important mechanism. Multiple, quite different mechanisms are relevant during the formation of the residue, and the importance of each mechanism probably differs from one nanocomposite system to another. The main fire protection effect of the surface layer in polymer nanocomposites based on non-charring or nearly non-charring polymers is the increase in surface temperature, resulting in a substantial increase in reradiated heat flux (heat shielding). KW - Nanocomposite KW - Fire retardancy KW - Epoxy resin KW - Fire behavior KW - Flammability PY - 2011 DO - https://doi.org/10.1002/pat.1644 SN - 1042-7147 SN - 1099-1581 VL - 22 IS - 12 SP - 1581 EP - 1592 PB - John Wiley & Sons, Ltd. CY - Chichester AN - OPUS4-24916 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gallo, Emanuela A1 - Schartel, Bernhard A1 - Braun, Ulrike A1 - Russo, P. A1 - Acierno, Domenico T1 - Fire retardant synergisms between nanometric Fe2O3 and aluminium phosphinate in poly(butylene terephthalate) N2 - The pyrolysis and the flame retardancy of poly(butylene terephthalate) (PBT) containing aluminum diethylphosphinate (AlPi) and nanometric Fe2O3 were investigated using thermal analysis, evolved gas analysis (Thermogravimetry-FTIR), flammability tests (LOI, UL 94), cone calorimeter measurements and chemical analysis of residue (FTIR). AlPi mainly acts as a flame inhibitor in the gas phase, through the release of diethylphosphinic acid. A small amount of Fe2O3 in PBT promotes the formation of a carbonaceous char in the condensed phase. The combination of 5 and 8 wt% AlPi, respectively, with 2 wt% metal oxides achieves V-0 classification in the UL 94 test thanks to complementary action mechanisms. Using PBT/metal oxide nanocomposites shows a significant increase in the flame retardancy efficiency of AlPi in PBT and thus opens the route to surprisingly sufficient additive contents as low as 7 wt%. KW - Poly(butylene terephthalate) (PBT) KW - Flammability KW - Metal oxide KW - Nanocomposite KW - Aluminum diethylphosphinate PY - 2011 DO - https://doi.org/10.1002/pat.1774 SN - 1042-7147 SN - 1099-1581 VL - 22 IS - 12 SP - 2382 EP - 2391 PB - John Wiley & Sons, Ltd. CY - Chichester AN - OPUS4-24915 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weidner, Steffen A1 - Falkenhagen, Jana T1 - LC-MALDI-TOF imaging MS: a new approach in combining chromatography and mass spectrometry of copolymers N2 - A new approach that utilizes MALDI-TOF imaging mass spectrometry as a new detector for polymer chromatography is presented. For the first time, the individual retention behavior of single structural units of polyethylene oxide (PEO)/polypropylene oxide (PPO) copolymers and changes of the copolymer composition could be monitored. Composition specific calibration curves could be easily obtained by displaying the copolymer ion intensity data. This approach provides completely new insights in the chromatographic principle of copolymer separation and could be used to easily modify and adapt conditions for separation. In combination with electrospray deposition, homogeneous sample/matrix traces of surprisingly high spatial resolution could be obtained. KW - MALDI KW - Massenspektrometrie KW - Imaging KW - Chromatographie KW - Polymere PY - 2011 DO - https://doi.org/10.1021/ac202380n SN - 0003-2700 SN - 1520-6882 VL - 83 IS - 23 SP - 9153 EP - 9158 PB - American Chemical Society CY - Washington, DC AN - OPUS4-24974 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppl, T. A1 - Wolff-Fabris, F. A1 - Altstädt, V. A1 - Ciesielski, M. A1 - Bykov, Y. A1 - Döring, M. A1 - Fischer, O. A1 - Brehme, Sven A1 - Schartel, Bernhard T1 - Comparison of Low-molecular and Polymeric Flame Retardants for Poly(butylene terephthalate) T2 - 12th biennial international Bayreuth Polymer Symposium, BPS'11 CY - Bayreuth, Germany DA - 2011-09-11 PY - 2011 AN - OPUS4-24764 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Towards Evidence-based Development of Flame Retarded Polymers T2 - Polymer- und Kunststoff Kolloquium CY - Darmstadt, Germany DA - 2011-11-24 PY - 2011 AN - OPUS4-24933 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Perret, Birgit A1 - Schartel, Bernhard A1 - Stöß, K. A1 - Ciesielski, M. A1 - Diederichs, J. A1 - Döring, M. A1 - Krämer, J. A1 - Altstädt, V. T1 - A new halogen-free flame retardant based on 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide for epoxy resins and their carbon fiber composites for the automotive and aviation industries N2 - The pyrolysis and fire behavior of halogen-free flame-retarded DGEBA/DMC, RTM6 and their corresponding 60 vol.-% carbon fibers (CF) composites were investigated. A novel phosphorous compound (DOPI) was used. Its action is dependent on the epoxy matrix. DGEBA/DMC and DOPI decompose independently of each other. Only flame inhibition occurs in the gas phase. RTM6 shows flame inhibition and a condensed phase interaction increasing charring. Both mechanisms decrease with increasing irradiance, whereas in RTM6-CF charring is suppressed at low ones. RTM6+DOPI shows a higher LOI (34.2%) than DGEBA/DMC+DOPI and a V-0 classification in UL 94. Adding CF only enhances the LOI, DOPI+CF leads to a superposition in LOI for DGEBA/DMC-CF+DOPI (31.8%, V-0) and a synergism for RTM6-CF+DOPI (47.7%, V-0). KW - Composites KW - Flame retardancy KW - Glass transition KW - Pyrolysis KW - Thermosets PY - 2011 DO - https://doi.org/10.1002/mame.201000242 SN - 1438-7492 SN - 1439-2054 VL - 296 IS - 1 SP - 14 EP - 30 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-22957 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yu, D. A1 - Kleemeier, M. A1 - Wu, Guang Mei A1 - Schartel, Bernhard A1 - Liu, W.Q. A1 - Hartwig, A. T1 - A low melting organic-inorganic glass and its effect on flame retardancy of clay/epoxy composites N2 - A low-melting organic-inorganic glass with a high molecular weight soluble in solvents was synthesized by hydrolytic polycondensation of phenyltriethoxysilane followed by a subsequent heat treatment. Softening point and thermostability were strongly increased after heat treatment. The composites of glass/epoxy and glass/clay/epoxy were studied with respect to their thermal properties, fire behavior and mechanical properties. Heat release rate as measured by cone calorimetry was remarkably reduced in the presence of glass, relative to neat epoxy resin and polymer/clay composites. The combination of glass and clay is a promising approach. It showed mainly superposition and even synergistic effects in some fire properties for higher filler concentrations due to the formation of an enhanced barrier. The structure of residue was investigated by transmission electron microscopy (TEM). KW - Low-melting glass KW - Clay KW - Epoxy resin PY - 2011 DO - https://doi.org/10.1016/j.polymer.2011.03.033 SN - 0032-3861 SN - 1873-2291 VL - 52 IS - 10 SP - 2120 EP - 2131 PB - Elsevier Ltd. AN - OPUS4-23858 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard ED - Gibson, A.G. T1 - Fire retardancy in composites: a journey from nano to intermediate scale N2 - The fire behaviour of composites clearly differs in comparison to polymers. Even though fibres and inorganic particles may be inert with respect to pyrolysis, they are clearly not with respect to fire behaviour. They change heat absorption and transfer within the Condensed phase, the melt flow/dripping behaviour of pyrolysing melts, the amount and properties of the fire residue and so on. Flame retardancy concepts tailored to composites are needed. Furthermore tasks that are specific for composites such as the structural integrity in fire get into the focus. Thus understanding of fire behaviour and flame retardancy mechanisms in composites is a key for target-oriented future development. The field is illuminated by Spotlights on different length scales. The examples are taken from different projects carried out in the group of the authors in the recent years. Flame retardancy mechanisms in nanocomposites are discussed, advanced halogen-free flame retardants for carbon and glass fibre composites presented as well as an approach to mechanical intermediate scale testing of carbon fibre composites under fire. T2 - Composites in fire 6 - 6th International conference on composites in fire CY - Newcastle, UK DA - 09.06.2011 KW - Flame retardancy KW - Composite KW - Composite and fire KW - Flame retardants PY - 2011 SN - 978-0-9540459-9-9 SP - 55 EP - 62 PB - CompositeLink (Consultants) Limited AN - OPUS4-23857 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gallo, Emanuela A1 - Schartel, Bernhard A1 - Acierno, Domenico A1 - Russo, P. T1 - Flame retardant biocomposites: Synergism between phosphinate and nanometric metal oxides N2 - The known flame-retardant synergism between phosphorus-based additives and metal oxides, already used for petroleum-based plastics, has been extended to bio-based materials. The pyrolysis and the flame-retardancy properties of aluminium phosphinate (AlPi) in combination with nanometric iron oxide and antimony oxide on a poly(3-hydroxy-butyrate-co-3-hydroxyvalerate)/poly(butylene adipate-co-terephthalate) (PHBV/PBAT) blend were investigated. Better fire retardancy, ascribed to increases in intermediate char, favoured improvements in the UL 94 classification. Both the phosphorus and the nanofiller components participate simultaneously in the flame-retardancy mechanism: the first acting as flame inhibition in the gas phase, and the second promoting cross-linking in the solid phase. Redox reactions between iron oxide and the phosphinate additive were confirmed by XRD analysis and provided further evidence of the activity of metal compounds. KW - Aliphatic biopolyesters KW - Metal oxide KW - Flame retardancy KW - Aluminium phosphinate PY - 2011 DO - https://doi.org/10.1016/j.eurpolymj.2011.04.001 SN - 0014-3057 SN - 1873-1945 VL - 47 IS - 7 SP - 1390 EP - 1401 PB - Elsevier CY - Oxford AN - OPUS4-23889 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bahlmann, Arnold A1 - Falkenhagen, Jana A1 - Weller, Michael G. A1 - Panne, Ulrich A1 - Schneider, Rudolf T1 - Cetirizine as pH-dependent cross-reactant in a carbamazepine-specific immunoassay N2 - High performance liquid chromatography (HPLC) was hyphenated with a previously reported carbamazepine-specific enzyme-linked immunosorbent assay (ELISA) as a screening approach to water analysis in order to identify possible interferences from transformation products. Treated wastewater was analysed and three substances were recognized by the antibody besides carbamazepine: the metabolites 10,11-dihydro-10,11-epoxycarbamazepine and 2-hydroxycarbamazepine plus the structurally not obviously related antihistamine cetirizine. The molar cross-reactivity against cetirizine was found to be pH-dependent and assessed to be 400% at pH 4.5 and 22% at pH 10.5. Performing the ELISA at pH 10.5 greatly improved the accuracy when carbamazepine was determined in surface and wastewater samples. KW - Immunoassay KW - ELISA KW - Cetirizin KW - Carbamazepin KW - pH-Abhängigkeit KW - Kreuzreaktivität PY - 2011 DO - https://doi.org/10.1039/c0an00928h SN - 0003-2654 SN - 1364-5528 VL - 136 IS - 7 SP - 1357 EP - 1364 PB - Royal Society of Chemistry CY - Cambridge AN - OPUS4-23546 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmid, C. A1 - Falkenhagen, Jana A1 - Barner-Kowollik, C. T1 - An efficient avenue to poly(styrene)-block-poly(Epsilon-caprolactone) polymers via switching from RAFT tio hydroxyl functionality: synthesis and characterization KW - 2D-liquid chromatography KW - End group transformation KW - LACCC-SEC KW - Reversible addition fragmentation chain transfer KW - Ring-opening polymerization KW - soft ionization mass spectrometry PY - 2011 DO - https://doi.org/10.1002/pola.24299 SN - 0360-6376 SN - 0887-624X VL - 49 IS - 1 SP - 1 EP - 10 PB - Wiley CY - Hoboken, NJ AN - OPUS4-22894 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altstädt, V. A1 - Köppl, T. A1 - Krämer, J. A1 - Wolff-Fabris, F. A1 - Döring, M. A1 - Pospiech, D. A1 - Schartel, Bernhard T1 - Phosphorous-based flame retardants for thermoplastic polyesters and carbon fibre reinforced epoxy composites T2 - 11th Annual UNESCO/IUPAC workshop & conference on functional polymeric materials & composites CY - Stellenbosch, South Africa DA - 2011-04-27 PY - 2011 AN - OPUS4-23416 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Falkenhagen, Jana A1 - Weidner, Steffen A1 - Schmid, Christina T1 - Hyphenated techniques for copolymer characterization with the focus on 2D-LC / mass spectrometry T2 - 5th Int.Symp. on the Separation and Characterization of Natural and Synthetic Macromolecules CY - Amsterdam, Netherlands DA - 2011-01-25 PY - 2011 AN - OPUS4-22657 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gallo, Emanuela A1 - Russo, P. A1 - Schartel, Bernhard T1 - Flame retardant PHBV/PBAT blends and biocomposites: synergism between aluminium phosphinate and iron oxide T2 - Advances in polymer based materials and related technologies - Workshop CY - Capri, Italy DA - 2011-05-29 PY - 2011 AN - OPUS4-23802 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Development of Fire-Retarded Materials - Interpretation of Cone Calorimeter Data T2 - Sixth International Conference on Composites In Fire CY - Newcastle upon Tyne, England DA - 2011-06-09 PY - 2011 AN - OPUS4-23898 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mieller, Björn A1 - Gemeinert, Marion A1 - Rabe, Torsten A1 - Brode, W. T1 - Druckgesinterte LTCC-Substrate für die Dünnfilmbeschichtung T2 - DKG-Jahrestagung 2011 CY - Saarbrücken, Germany DA - 2011-03-28 PY - 2011 N1 - Geburtsname von Mieller, Björn: Brandt, B. - Birth name of Mieller, Björn: Brandt, B. AN - OPUS4-23490 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Fire Retardancy in Composites: A Journey from Nano to Intermediate Scale T2 - Sixth International Conference on Composites In Fire: CIF6 CY - Newcastle upon Tyne, England DA - 2011-06-09 PY - 2011 AN - OPUS4-23826 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weidner, Steffen A1 - Falkenhagen, Jana T1 - MALDI Imaging MS von Polymeren T2 - BRUKER-Anwendertreffen CY - Kassel, Germany DA - 2011-03-21 PY - 2011 AN - OPUS4-23603 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -