TY - GEN ED - Rockland, Ulrike T1 - Jahresbericht 2007 T1 - Annual report 2007 T3 - BAM Reports/Jahresberichte - 2007 PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-4564 SN - 0934-9456 N1 - Volltext (PDF) in deutsch und englisch - Full text (PDF) in German and English VL - 2007 SP - 1 EP - 153 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-456 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Coniglio, Nicolas T1 - Aluminum Alloy Weldability: Identification of Weld Solidification Cracking Mechanisms through Novel Experimental Technique and Model Development N2 - The objective of the present thesis is to make advancements in understanding solidification crack formation in aluminum welds, by investigating in particular the aluminium 6060/4043 system. Alloy 6060 is typical of a family of Al-Mg-Si extrusion alloys, which are considered weldable only when using an appropriate filler alloy such as 4043 (Al-5Si). The effect of 4043 filler dilution (i.e. weld metal silicon content) on cracking sensitivity and solidification path of Alloy 6060 welds are investigated. Afterwards, cracking models are developed to propose mechanisms for solidification crack initiation and growth. Cracking Sensitivity. Building upon the concept that silicon improves weldability and that weldability can be defined by a critical strain rate, strain rate-composition combinations required for solidification crack formation in the Al- 6060/4043 system were determined using the newly developed Controlled Tensile Weldability (CTW) test utilizing local strain extensometer measurements. Results, presented in a critical strain rate – dilution map, show a crack – no crack boundary which reveals that higher local strain rates require higher 4043 filler dilution to avoid solidification cracking when arc welding Alloy 6060. Using the established crack - no crack boundary as a line of reference, additional parameters were examined and their influence on cracking characterized. These parameter influences have included studies of weld travel speed, weld pool contaminants (Fe, O, and H), and grain refiner additions (TiAl3 + Boron). Each parameter has been independently varied and its effect on cracking susceptibility quantified in terms of strain rate – composition combinations. Solidification Path. Solidification path of the Al-6060/4043 system was characterized using thermal analysis and phase identification. Increasing 4043 filler dilution from 0 to 16% in Alloy 6060 arc welds resulted in little effect on thermal arrests and microstructure, no effect on solidification range, refinement in grain size from 63 to 51 μm, centerline columnar grains disappearance, and decreased cooling rate from 113 to 89 °C/s. Moreover, in order to make direct comparison with literature, castings of controlled mixtures of alloys 6060 and 4043 were also investigated, thereby simulating weld metal composition under controlled cooling conditions. Castings showed a different trend than welds with small increases in silicon content (i.e. increase in 4043 filler dilution) resulting in huge effect on microstructure, no effect on liquidus temperature, drop in solidus temperature from 577°C to 509°C, increase in quantity of interdendritic constituent from 2% to 14%, and different phase formation. Binary β-Al5FeSi, Mg2Si, and Si phases are replaced with ternary β-Al5FeSi, π−Al8FeMg3Si6, and a low melting quaternary eutectic involving Mg2Si, π, and Si. Also, variation of the cooling conditions in castings revealed the existence of a critical cooling rate, above which the solidification path and microstructure undergo a major change. Cracking Model. Implementing the critical conditions for cracking into the Rappaz-Drezet-Gremaud (RDG) model revealed a pressure drop in the interdendritic liquid on the order of 10-1 atm, originating primarily from straining conditions. Since, according to literature, a minimum of 1,760 atm is required to fracture pure aluminum liquid (theoretical), this demonstrates that cavitation as a liquid fracture mechanism is not likely to occur, even when accounting for dissolved hydrogen gas. Instead, a porosity-based crack initiation model has been developed based upon pore stability criteria, assuming that gas pores expand from pre-existing nuclei. Crack initiation is taken to occur when stable pores form within the coherent dendrite region, critical to crack initiation being weld metal hydrogen content. Following initiation, a mass-balance approach developed by Braccini et al. (2000) revealed that crack growth is controlled by local strain rate conditions. Finally, a simplified strain partition model provides a link between critical strain rates measured across the weld and predicted at grain boundaries within the mushy zone. Although based on simplified assumptions, predicted and measured critical strain rate values are of the same order of magnitude. However, because of a longer mushy zone experienced at higher 4043 filler dilution related to a reduction in cooling rate, these models predict a lower weldability with increasing filler dilution, in contradiction with experimental observations. Combining the crack initiation and growth models suggests that hydrogen and strain rate, respectively, determine crack formation. An hypothetical hydrogen – strain rate map defines conceptually the conditions for cracking, suggesting better weldability at low weld metal hydrogen content. With the aid of the modified varestraint test (MVT) and a controlled hydrogen contamination system, results, presented in the form of ram speed – hydrogen map, revealed that hydrogen has little effect on crack growth, providing support to the proposed cracking models. However, a drop in weldability corresponding to the peak in weld metal hydrogen supersaturation suggests a different solidification cracking mechanism, where cavitation supports crack growth. T3 - BAM Dissertationsreihe - 40 KW - Aluminum Weldability KW - Crack Initiation-Growth KW - Mechanism Modeling KW - Critical Strain Rate-Dilution KW - Solidification Cracking PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1183 SN - 978-3-9812354-3-2 SN - 1613-4249 VL - 40 SP - 1 EP - 208 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-118 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Stelling, Karen T1 - Laserstrahl-Plasma-Hybridschweißen austenitischer Stähle N2 - Als eine neue Verfahrensvariante unter den Laserstrahl-Lichtbogen- Hybridschweißverfahren wird das Laserstrahl-Plasma-Hybridschweißen für die Werkstoffgruppe der austenitischen Stähle entwickelt. Neben der Entwicklung eines Hybridschweißkopfes, der für die Kopplung von Plasmalichtbogen und Laserstrahl in einer gemeinsamen Prozesszone ausgelegt ist, liegt ein Schwerpunkt auf der Ermittlung des Einflusses wichtiger Schweißparameter auf das Schweißergebnis und fertigungsrelevanter Kenngrößen wie der erzielbaren Spaltüberbrückbarkeit. Unter Einsatz eines pulverförmigen Zusatzwerkstoffes, der über den Plasmabrenner in die Prozesszone überführt wird, werden dazu Schweißnähte am Stumpfstoß sowie im Überlappstoß angefertigt. Aufbauend auf Ergebnissen aus Schweißversuchen wird ein Modell erstellt, das zu einem besseren Verständnis der Vorgänge im gemeinsamen Schmelzbad von Plasmalichtbogen- und Laserstrahlprozess beitragen soll, indem es die Auswirkung einzelner Schweißparameter auf das Schweißergebnis, wie zum Beispiel die Porenbildung, und somit indirekt die im Schmelzbad wirkenden Kräfte qualitativ einbezieht. Als Basis für die Erstellung des Modells dienen röntgenographische Aufnahmen, metallographische Untersuchungen als auch Hochgeschwindigkeits- aufnahmen des Hybridschweißprozesses. Weiterhin bilden metallurgische Aspekte bzw. die sich einstellenden Erstarrungsgefüge dieser Stähle einen weiteren Untersuchungsschwerpunkt in dieser Arbeit. Die im Schweißgut der Hybridnähte vorliegenden Erstarrungsmodi werden ermittelt und unterschiedliche prozessrelevante Einflüsse auf das Gefüge identifiziert. Darüber hinaus werden der Ferritgehalt sowie die Härte in den unterschiedlichen Zonen des Schweißnahtgefüges bestimmt. Mit der vorliegenden Arbeit liegen Ergebnisse vor, die zur effizienteren Gestaltung von Schweißprozessen im Blechdickenbereich von 5 mm bis 8 mm beitragen können und gleichzeitig auf werkstoffspezifische Besonderheiten der austenitischen Stähle beim Laserstrahl-Plasma-Hybridschweißen mit einem pulverförmigem Zusatzwerkstoff hinweisen. N2 - The laser plasma hybrid welding process – as a novel type of laser-arc combination – is developed for welding fabrication of austenitic stainless steels. The design of a hybrid welding torch and the evaluation of the influence of important welding parameters on the weld constitute two major aspects of this work. Butt joints and overlap welds are fabricated in order to gain data, which are relevant to welding fabrication such as gap bridging ability. Metal powder is used as filler material, which is transferred to the process zone via the plasma torch. With the intention to get a better understanding of the interactions of plasma arc and laser beam process in the common welding zone, a model is developed that is based on the results of the welding experiments. This model takes into account the effects of individual welding parameters on process behaviour such as pore formation and, thus, indirectly implies the various forces on the molten pool. The model was derived from radiographic and metallographic examination of the welds as well as from observation of the hybrid welding process using a high speed camera. Additionally, metallurgical aspects or rather the solidification structures of the austenitic stainless steel welds represent another main focus of this research work. The solidification modes are identified and various process relevant influences are established. Moreover, the ferrite Content and the hardness of the different zones of the weld are measured. This work provides results that may contribute to increase the efficiency of welding processes in the plate thickness range of 5 mm to 8 mm. In addition, material-specific features of the austenitic steels during laser plasma hybrid welding with a metal powder as filler material are indicated. T3 - BAM Dissertationsreihe - 39 KW - Laserstrahl-Plasma-Hybridschweißen KW - austenitische Stähle KW - Hybridschweißprozess KW - Hybridschweißkopf KW - Erstarrung PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1195 SN - 978-3-9812354-2-5 SN - 1613-4249 VL - 39 SP - 1 EP - 151 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-119 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Flatten, Arnd T1 - Lokale und nicht-lokale Modellierung und Simulation thermomechanischer Lokalisierung mit Schädigung für metallische Werkstoffe unter Hochgeschwindigkeitsbeanspruchungen N2 - Hochgeschwindigkeitsbeanspruchungen metallischer Bauteile sind bei einer Vielzahl ingenieurtechnischer Anwendungsbereiche, beispielsweise bei Crash- oder Falltests, bei Umform- oder Spanprozessen mit hohen Belastungsgeschwindigkeiten oder bei Aufprallproblemen von Komponenten schnell rotierender Bauteile auf das umgebende Gehäuse, z. B. bei Flugzeugturbinen, relevant. Dabei treten in dem beanspruchten Bauteil typischerweise Zonen mit großen, lokalisierten Deformationen auf, die auf die Entfestigung des Werkstoffs durch die Entwicklung von Schädigung und durch die Temperaturerhöhung infolge plastischer Dissipation zurückzuführen sind. Die Ausbildung von Scherbändern stellt dabei eine typische Form der Deformationslokalisierung dar. Die kontinuumsmechanische Modellierung solcher Vorgänge erfordert im Allgemeinen die Berücksichtigung einer Vielzahl von Faktoren und Effekten, wie beispielsweise dehnraten- abhängiges Materialverhalten, mit adiabatischer Erhitzung einhergehende thermische Entfestigung, Reibung und Kontakt sowie Schädigung. Darüber hinaus sind die genannten Effekte in dem Rahmen der Theorie großer Deformationen zu betrachten. Dehnratenabhängige ”lokale“ Modelle resultieren dabei nicht zwangsläufig in einer physikalisch sinnvollen Scherbandabbildung, d. h. in einer endlichen Scherbandbreite. Die innere Länge, die eine Begrenzung des Lokalisierungsvolumens darstellt, strebt für verschiedene im Rahmen der Simulation von Hochgeschwindigkeitsbelastungen eingesetzte, nichtlinear dehnratenabhängige Modelle, wie z.B. Potenzgesetz-Modelle oder dem Modell nach JOHNSON&COOK, mit infolge von Entfestigung abnehmender Spannung sowie zunehmender plastischer Dehnrate sehr stark gegen null. Dadurch tritt ein Verlust der lokalisierungsbegrenzenden Wirkung dieser ratenabhängigen Modelle ein, so dass insbesondere jedes, auf diesen Modellen aufbauende Finiten-Element Verfahren eine pathologische Netzabhängigkeit der Ergebnisse aufweist. ”Nicht-lokale“ Gradientenmodelle der Plastizität sind dazu geeignet, die beschriebenen Nachteile zu vermeiden. Die innere Länge dieser Modelle weist eine im Vergleich zu lokalen Modellen deutlich reduzierte Abhängigkeit von dem vorherrschenden Spannungszustand sowie der plastischen Dehnrate auf und wird darüber hinaus wesentlich durch den Wert des nichtlokalen Modellparameters beeinflusst. Die Größenordnung der inneren Länge bleibt dabei selbst für kleine Werte dieses Parameters auch mit Einsetzen von Lokalisierungseffekten zunächst erhalten. Infolge der numerischen Umsetzung nicht-lokaler Modelle mittels der Methode der Finiten- Elemente zeigt sich, dass im Gegensatz zu den auf lokalen Modellen basierenden Verfahren das Volumen der Lokalisierungszone bei stetiger Netzverfeinerung gegen einen endlichen Wert konvergiert. Damit gelingt es durch die Verwendung nicht-lokaler Modelle, die Ausbildung endlicher Scherbanddicken diskretisierungsunabhängig zu simulieren und im Rahmen der Kontinuumsmechanik eine sinnvolle Lösung des zugrunde liegenden physikalischen Problems zu gewährleisten. N2 - High-speed loading of metals is encountered in several engineering applications, for example in crash and drop tests as well as in high-speed cutting or forming processes. Likewise, the impact of rapidly rotating structural components on their surrounding containment, encountered for instance in aircraft turbines, reveals significant, high loading velocities. Typically, this type of loading results in zones with highly localized deformation within the stressed component, as a consequence of softening according to damage evolution and heating due to plastic dissipation. In this context, the formation of shear-bands represents a typical form of thermomechanical localization. In general, the continuum mechanical description and modelling of such events involves a variety of processes and effects such as high strain-rates, hardening behaviour, thermal softening as a result of adiabatic heating, friction and contact as well as damage. Further, These effects need to be considered in the framework of large deformation theory. Rate-dependent ”local” models do not generally result in a physical shear-band development, e.g., involving a finite, non-vanishing shear-band thickness. In general, the intrinsic length incorporated by the rate-dependency of the models acts as a localization limiter. However, for various nonlinearly rate-dependent models, such as power-law models or the model according to JOHNSON&COOK, which are frequently used for the simulation of high-speed loading applications, this intrinsic length tends to zero owing to both increasing strain-rates and stress-drop due to softening behaviour. Thus, a loss of the localization limiting property of these rate-dependent models is encountered, incorporating that each finite-element method based upon these models yields a pathological mesh-dependence of the results. ”Non-local” gradient-plasticity models based on a corresponding extension of the rate-dependence of the material behaviour are appropriate to avoid these disadvantages. In contrast to local models, the intrinsic length of these non-local models reveals a significantly reduced dependence on both the prevailing stress state and the plastic strain-rate but is dominantly influenced by the non-local material parameter. According to the numerical simulation of localization phenomena using finite-element techniques, the domain of the localization zone does converge to a finite volume for subsequent mesh-refinement. Thus, using non-local models it is possible to simulate the development of finite shear-band widths and to ensure a physically reasonable solution of the governing problem within the framework of continuum mechanics. T3 - BAM Dissertationsreihe - 38 KW - Finite-Elemente-Methode KW - Hochgeschwindigkeitsbeanspruchungen KW - Gradienten-Plastizität KW - Adiabatische Scherbänder KW - Komponentensicherheit KW - Finite-Element-Method KW - High-Speed Loading KW - Gradient Plasticity KW - Adiabatic Shear Bands KW - Component-Safety PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1200 SN - 978-3-9812072-9-3 SN - 1613-4249 VL - 38 SP - 1 EP - 199 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-120 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Anders, Stefan T1 - Sensitivitätsanalyse des Eigenspannungszustandes eines Composite-Hybridhochdruckbehälters N2 - Die Automobilindustrie sucht nach Lösungen, um Emissionen zu reduzieren, und nach Alternativen zu fossilen Brennstoffen, deren Verfügbarkeit über die nächsten Dekaden abnehmen wird. Aus diesem Grund gewinnen komprimiertes Erdgas sowie Wasserstoff als Energieträger zunehmend an Bedeutung. Um befriedigende Reichweiten mit komprimiertem Gas zu erreichen, wird ein Betriebsdruck von 20 MPa bis zu 70 MPa (nur Wasserstoff) angewandt. Die Hochdruckbehälter müssen die statischen und die dynamischen Innendruck- sowie die thermische Belastung ertragen. Gleichzeitig soll der Behälter eine sichere, aber auch eine wirtschaftliche Leichtbaustruktur sein, welche nur mit Hybridstrukturen (Metall- oder Polymerliner mit Kohlefaser- bzw. Glasfaserumwicklung an der Außenseite) realisiert werden kann. Wegen der Vielzahl an veränderlichen Produktionsparametern zeigen Composite- und speziell Hybridstrukturen große Streuungen in ihrem Strukturverhalten. Die dargestellten Versuchsdaten, welche an industriell gefertigten Composite-Hybriddruckbehältern gemessen wurden, zeigen dieses Problem. Um das Material im Sinne des Leichtbaus effizient zu nutzen und um gleichzeitig einen hohen Grad an Sicherheit mit reproduzierbarem Strukturverhalten zu realisieren, wird ein besseres Verständnis für das Verhalten des Hybriddesigns benötigt. Neben der Betrachtung der Imperfektionen im Composite und der benötigten Messmethoden für die Charakterisierung der Strukturparameter ist das Hauptanliegen der vorliegenden Arbeit die Simulation des Eigenspannungszustandes, resultierend aus der Produktion und dem Betrieb, sowie dessen Auswirkung. Um den Einfluss der verschiedenen Strukturparameter auf das Verhalten des Hochdruckbehälters mittels einer Sensitivitätsanalyse zu untersuchen, wurde ein geschlossen analytisches parametrisiertes Modell erstellt. Für die effektive Parametervariation sind hierfür analytische Modell von Vorteil im Vergleich zu FEM-Modellen. Das vorgestellte nichtlineare analytische Modell berücksichtigt den Einfluss des Eigenspannungszustandes des Autofrettageprozesses, in welchem der Liner kontrolliert durch Innendruck plastifiziert wird. Ebenso werden die Steifigkeitsdegradation infolge von Zwischenfaserbrüchen im Composite bei der Erstbeanspruchung (Degradationsmodell nach Puck), die thermischen Eigenspannungen infolge der verschiedenen Wärmeausdehnungskoeffizienten und der temperaturabhängige E-Modul des Harzsystems berücksichtigt. Die umfangreichen Versuchsdaten validieren die analytische Simulation zufriedenstellend. Die Simulation zeigt, dass der Schichtspannungszustand inklusiv des Eigenspannungszustandes stark von den Parametern Temperatur und Innendruck während der Produktion sowie im Betrieb abhängig sind. Diese Effekte sind bei einer erweiterten Spannungsanalyse der Behälterstruktur zu berücksichtigen. N2 - The automotive industry is looking for solutions to reduce emissions and the dependency on fossil fuels, whose availability is predicted to decrease over the next decades. For this reason, compressed natural gas and hydrogen as energy are gaining more and more in importance as replacements for fossil fuels. In order to achieve a satisfying energy density for automotive application with compressed gas storage systems an operating pressure from 20 MPa up to 70 MPa (hydrogen only) is applied. The pressure cylinder has to withstand the static and dynamic pressure as well as temperature loads. At the same time the cylinder has to be an economical and safe light weight structure which can be accomplished with hybrid structures (metal or polymer liner with carbon or glass fiber winding on the outside) only. Due to their multi-dependency on production parameters composite structures and especially hybrid structures show a high spread in structural parameters. The presented test data which had been measured on industrial composite-hybrid pressure cylinders of the same type revealed this problem. In order to exploit the material properties with a high degree of lightweight optimization efficiently, a high level of safety and, with an improved degree of reproducibility at the same time, a better understanding of the structural behavior of hybrid design is necessary. Besides considering the imperfection of the composite layer and the use of appropriate measuring methods to determine the structural parameters, the main concern of the presented work is to simulate the level and the influence of residual stresses occurring during production and operation. To investigate the influence of variable structural parameters on the behavior of the high pressure cylinder by means of a sensitivity analysis a parametric analytical closed form model has been built. For this application, which is characterized by a wide range of parameters, analytical models are superior to FEM-models in flexibility and processing speed. The presented nonlinear analytical model considers the influence of the residual stresses introduced purposely by the autofrettage process in which the metal liner is loaded beyond the yielding point. It also takes into account the degradation of Young’s modulus caused by inter-fibre fracture during the first pressurization (according to Puck’s action-plane fracture criteria), the residual stress due to the different thermal coefficients of expansion (composite and metal) and the influence of temperature on the resin system close to the glass transition temperature. The large amount of acquired test data validated the analytical simulation satisfactorily. The simulation showed that the layer’s stress level including the residual stress strongly depends on the parameters temperature and pressure during production and also during operation of the cylinder. These effects have to be considered for a sophisticated stress analysis of the structure. T3 - BAM Dissertationsreihe - 37 KW - Autofrettage, KW - Composite-Metall-Hybrid Hochdruckbehälter KW - CLT KW - Temperatur-Fertigungseigenspannungen KW - 2D geschlossen-analytische Spannungsanalyse PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1210 SN - 978-3-9812072-8-6 SN - 1613-4249 VL - 37 SP - 1 EP - 164 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-121 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Wongpanya, Pornwasa T1 - Effects of Heat Treatment Procedures on the Cold Cracking Behaviour of High N2 - Most of the research on Hydrogen Assisted Cold Cracking (HACC) in high strength steel welds conducted over the last several decades has focused on single-pass welds, especially considering materials with yield strengths of about 700 MPa. Most of the weld procedure specifications, guidelines and standards targeted at HACC avoidance recommend preheating procedures. Application of such regulations to multi-pass welds of modern high strength structural steels with yield strengths of up to 1300 MPa is very limited. Actually there is no decent knowledge and only an empirical experience how to weld such joints in real components subjected to a respective shrinkage restraint. Consequently, an increasing number of failure cases, partly of catastrophic dimensions, have been reported in the present decade. The present contribution is targeted to close this knowledge gap by elucidating the principal effects of various inhomogeneous Hydrogen Removal Heat Treatment (HRHT) procedures on the HACC avoidance in high strength structural steel welds. As a typical representative in the upper yield strength range of this category of materials, a S 1100 QL weld using UNION X96 filler wire has been chosen. The results were achieved by indirectly coupled thermal, structural and hydrogen diffusion finite element modeling of HACC in single-layer and five-layer welded V-bevelled butt joints with plate thicknesses of 20.0 mm and 12.0 mm, respectively, at realistic restraint conditions and have been partly been confirmed by respective Instrumented Restraint Cracking (IRC) Tests. The numerical simulations are based on the interacting three local effects on HACC, i.e. local microstructure, local mechanical load and local hydrogen concentration. HACC has thus been regarded as a cracking phenomenon occurring, if the local mechanical load in a specific microstructure exceeds the limit for the respective hydrogen concentration. The various heat treatments proposed in literature, guidelines, specifications and standards, i.e. sole preheating, controlled interpass temperature, combined preheating and controlled interpass temperature application as well as postheating have been investigated with respect to their effects on the mechanical loading of the butt joints in terms of stresses and strains as well as on the hydrogen removal capabilities. As a particular item, a numerical model for Hydrogen Assisted Stress Corrosion Cracking (HASCC) has been developed further that it can be applied to HACC, in order to study, how such heat treatments influence crack initiation and propagation. By such modeling procedures as the most important results have been achieved: I. Further development and adaptation of a model for hydrogen assisted cracking to HACC and usage validation of the model for this material. II. Evaluation of the effects of pre- and postheating as well as interpass temperature on the stress-strain distribution in multi-pass welds. III. Clarification of the difference between single- and multi-pass welding with respect to stress-strain and hydrogen distribution as well as to HACC initiation and propagation. IV. Establishment of practical hydrogen removal heat treatment diagrams. V. Assessment of the effects of the amount of hydrogen picked up during welding on crack location and propagation. T3 - BAM Dissertationsreihe - 36 KW - High strength steel KW - numerical simulation KW - IRC test KW - hydrogen assisted cold cracking KW - crack Avoidance PY - 2008 SN - 978-3-9812072-7-9 SN - 1613-4249 VL - 36 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-122 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Hölck, Ole T1 - Gas Sorption and Swelling in Glassy Polymers Combining Experiment, Phenomenological Models and Detailed Atomistic Molecular Modeling N2 - Durchgeführte Arbeiten: In der vorliegenden Arbeit werden grundlegende Fragen zur Gas-Sorption und der damit verbundenen Quellung von glasigen Polymeren untersucht. Dabei wurde eine kombinierte Analyse aus experimenteller Charakterisierung, detailliert atomistischer Modellierung und phänomenologisch-theoretischer Betrachtung angewandt. Drei unterschiedliche Polymere, ein Polysulfon (PSU), ein Polyimid (PI4) und ein neuartiges Polymermaterial (PIM-1), wurden experimentell bezüglich ihrer Sorptions- und Quellungseigenschaften unter CO2- und CH4-Atmosphären bis zu 50 bar charakterisiert. Die Kinetik der Prozesse der experimentell gemessenen Gasaufnahme und Volumendilatation wurde analysiert, wobei zwei Anteile unterschieden werden konnten: Ein diffusiv/elastischer Anteil und ein relaxiver Anteil, der bei längerer Messzeit und höheren Drücken signifikant wird. Zusätzlich zu dieser Ermittlung von Konzentrations-Druck- bzw. Dilatations-Druck- Isothermen (differentielle Messung) wurden sogenannte integrale Sorptions- und Dilatationsmessungen (‘Ein-Schritt’-Messungen) durchgeführt, die als Referenz für eine entsprechende molekulardynamische (MD) Simulation elastischer Dilatationseffekte dienten. Für die detailliert atomistischen MD Simulationen wurden equilibrierte Packungsmodelle der (ungequollenen) Polymere erstellt. Für jeweils einen weiteren Referenzzustand, charakterisiert durch Druck, aufgenommene Gasmenge und Quellung, wurden CO2- und CH4-beladene (gequollene) Packungsmodelle erstellt und durch NpT -MD Simulation equilibriert. Die Packungsmodelle der reinen (ungequollenen) Polymere und der CO2- gequollene Zustand wurden jeweils bezüglich ihres freien Volumens quantitativ charakterisiert. Die gefundenen Unterschiede konnten weiterhin durch eine detaillierte 3D- Visualisierung des Freien Volumens veranschaulicht werden. Für alle Packungsmodelle wurden großkanonische Monte Carlo (gcmc) Simulationen durchgeführt, die jeweils zu Konzentrations-Druck-Isothermen führten. Experimentelle Daten und Simulationsergebnisse wurden in Bezug auf drei theoretische Modelle (Dual Mode Sorption Model (dm), Site Distribution Model (sd), und Non-Equilibrium Thermodynamics of Glassy Polymers (net-gp)) ausgewertet und diskutiert. Außerdem wurden die ungequollenen Packungsmodelle nach experimenteller Spezifikation aus integralen Sorptionsmessungen mit dem jeweiligen Gas beladen und die elastische Dilatation während der folgenden NpT -MD Equilibrierung beobachtet. Ergebnisse: Die konsistente Anwendung der Ergebnisse der kinetischen Analyse führt zu einer verbesserten Übereinstimmung theoretischer Modelle mit dem Experiment und deutlich zuverlässigerer Bestimmung von Modellparametern. Deren physikalische Bedeutung ermöglicht erste Ansätze für eine universelle Beschreibung grundlegender Stofftransporteigenschaften. Eine mögliche Limitierung des sd Modells bezüglich der Anwendbarkeit auf hochfreivolumige Polymere, wie sie im Rahmen dieser Arbeit festgestellt wurde, konnte dahingehend erklärt werden, dass die Gas-Matrix Wechselwirkung eine andere Besetzungsreihenfolge von Sorptionsplätzen bedingt, als bisher vom sd Modell angenommen. Die simulierten Isothermen konnten durch die Einführung eines linearen Übergangs zwischen der jeweils für ungequollenes und gequollenes Packungsmodell berechneten gcmc-Isothermen in gute Übereinstimmung mit dem Experiment gebracht werden. Die Verwandschaft der Methode mit dem net-gp Modell wird erörtert und die Ergebnisse mit der Vorhersage der Sorption des Modells verglichen. Die Freie-Volumen-Analyse zeigt deutliche Unterschiede zwischen den Polymeren PSU und PI4 einerseits und PIM-1 andererseits. In PIM-1 liegt ein großer Teil des Freien Volumens in einer Art losem Verbund einzelner ‘Löcher’ vor, der in dieser Arbeit als ‘Lochphase’ (‘void phase’) diskutiert wird. Im Gegensatz zu den gequollenen Packungen von PSU zeigen diejenigen von PI4 bereits Ansätze zur Bildung einer solchen Lochphase. Diese ist in gequollenen PIM-1 Packungen stärker ausgeprägt. Die gefundenen Größenverteilungen Freier Volumen-Elemente in den ungequollenen Packungsmodellen zeigen eine gute Übereinstimmung mit den aus der sd Analyse erhaltenen Gaußverteilungen. Außerdem konnte die elastische Dilatation, die in integralen Messungen experimentell beobachtet wird, erfolgreich in entsprechenden MD-Simulationen nachempfunden werden. Ein Zusammenhang zwischen den Abweichungen der Absolutwerte und möglichen anelastischen Reaktionen der Polymeratrix wird diskutiert. Die gute Übereinstimmung experimenteller Ergebnisse mit den Resultaten aus der Simulation sorgfältig ausgewählter Aspekte der Gas-Sorption und Quellung in glasigen Polymeren bestätigt sowohl die Qualität der erstellten Packungsmodelle als auch die Vorteile der generellen Herangehensweise. Die Ergebnisse dieser Arbeit zeigen, dass die Diskrepanz in Zeitskalen von Experiment und Simulation und die daraus resultierende scheinbare Inkompatibilität mit Hilfe hänomenologischer Modelle überbrückt werden kann, und damit wertvolle Erkenntnisse über die zugrunde liegenden Phänomene gewonnen werden. N2 - The behavior of amorphous polymers in contact with gas atmospheres is still an area of both fundamental scientific and applied industrial research. Applications range from the use as barrier materials or protective coatings to active layers in sensor applications (‘artificial nose’) and the large field of gas separation membranes. In all these applications, high concentrations of small penetrant molecules may lead to a plasticization of the polymer. This effect is utilized in processing applications, where supercritical carbon dioxide (CO2) can be used as a plasticizer.4 The phenomenon of penetrant induced plasticization of glassy polymers is also observed in gas separation membranes.5 In the process of natural gas sweetening, the CO2 content of the gas mixture is reduced by separation of the CO2 from the fuel gas methane (CH4) to avoid corrosion of pipelines and to enhance the fuel value. Solubility and diffusivity of the respective gas determine the separation performance of the membrane material, i.e., the permselectivity. Both parameters are connected to the internal structure of the polymer and its free volume. To achieve high throughputs, e.g. to enhance costeffectiveness, it is desirable to increase the CO2 solubility and mobility. However, the observed plasticization and the associated relaxations in the polymer matrix change its structure and free volume, and thereby affect the selectivity of the material.6 In addition, other properties of the polymer are influenced, e.g. a reduction of glass transition temperature,7 yield stress8 and creep compliance9 have been observed. The origin and mechanism of these structural relaxations are poorly understood, as are the factors that influence solubility and mobility of the plasticizing penetrant. This lack of knowledge leads to a development of new or optimized materials, which is in part determined by trial and error. A deeper understanding of the phenomena that accompany gas sorption on the molecular level is therefore needed to control material properties and enable a targeted design of functional materials. Therefore, in this work, laboratory experiments are combined with detailed atomistic molecular simulations. Modelling. In detailed atomistic molecular modeling, the interactions of an assembly of atoms, e.g. a polymer molecule, are calculated according to known physical laws. Several established analysis methods allow an indirect determination of certain properties of such assemblies, others can even be directly calculated.10 However, CPU-power limits both the size and the simulation time of such assemblies. The size of the simulated packing models used in this work (_ 5000 atoms) ranges among the larger models found in the literature. Forcefield based Molecular Dynamics (MD) simulations are calculated in femtosecond steps, but reliable results are usually not obtained until a nanosecond of net simulation time has been performed. Millions of interactions need to be calculated, making the time effort for these ‘virtual experiments’ comparable to laboratory experiments. However, increasing speed of single processors and the possibility of parallel processing will further reduce the evaluation times for such simulations in the future. The goal of computer simulations is therefore to establish reliable methods to predict material properties. Properties of new materials could then be assessed by simulations first and only the most promising materials need to be synthesized for further testing, reducing the expense of trial and error. Although some methods already exist to predict polymer/gas properties from simulations, which show well agreeing results in ideal circumstances, they frequently fail when applied to less moderate conditions, e.g., high penetrant concentrations, long time scales, large penetrants etc. The aforementioned gas induced plasticization of polymers presents such a case where the gap of time scales between experiment and available simulation time amounts to several orders of magnitude. The time scale of simulations is limited to a few nanoseconds and therefore it is not possible to directly simulate relaxations of the glassy matrix as they are observed experimentally. Experiments, on the other hand, yield results of the real macroscopic system, and though molecular details cannot be observed individually, the accumulated effects permit the analysis through models on a statistical or phenomenological basis. It is the aim of this work to survey new approaches of a combined analysis of experimental and modelling results and to establish, where possible, a convergence of boundary conditions or, alternatively, an identification and isolation of comparable aspects of these seemingly incompatible methods of research. To this effect, phenomenological models are utilized as a means of interpretation of experimental data as well as to construe modelling results. T3 - BAM Dissertationsreihe - 35 KW - Glasige Polymere KW - Sorption KW - Quellung KW - Simulation KW - Gastransport KW - glassy polymers KW - sorption KW - swelling KW - simulation KW - gas transport PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1235 SN - 978-3-9812072-5-5 SN - 1613-4249 VL - 35 SP - 1 EP - 135 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-123 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Maltsev, Sergey T1 - Structural elucidation of nanocrystalline biomaterials N2 - Bone diseases, such as osteoporosis and osteoarthritis, are the second most prevalent health problem worldwide. In Germany approximately 5 millions people are affected by arthritis. Investigating biomineralization processes and bone molecular structure is of key importance for developing new drugs for preventing and healing bone diseases. Nuclear magnetic resonance (NMR) [2] was the primary technique used due to its advantages in characterising poorly ordered and disordered materials [3]. Compared to all the diffraction techniques that widely applied in structural investigations, the usefulness of NMR is independent of long range molecular order. This makes NMR an outstanding technique for studies of complex/amorphous materials. Conventional NMR experiments (single pulse, spin-echo, cross polarization (CP) [4], etc.) as well as their modifications and high-end techniques (2D HETCOR [5], REDOR [6], etc.) were used in this work. Combining the contributions from different techniques enhances the information content of the investigations and can increase the precision of the overall conclusions. Also XRD, TEM and FTIR were applied to different extent in order to get a general idea of nanocrystalline hydroxyapatite crystallite structure. Results: - A new approach named “Solid-state NMR spectroscopy using the lost I spin magnetization in polarization transfer experiments” [7] has been developed for measuring the transferred I spin magnetization from abundant nuclei, which is normally lost when detecting the S spin magnetization. - A detailed investigation of nanocrystalline hydroxyapatite core was made to prove that proton environment of the phosphates units and phosphorus environment of hydroxyl units are the same as in highly crystalline hydroxyapatite sample. - Using XRD it was found that the surface of the hydroxyapatite nanocrystals is not completely disordered, as it was suggested before, but resembles the hydroxyapatite structure with HPO4 2-(and some CO3 2-) groups instead of PO4 3- groups and water instead of OH- groups. - The organic-mineral interface of bone was studied in order to clarify which organic molecules are in the closest spatial proximity to the bone mineral phase and to investigate the influence of the organic matrix on the mineral formation. It was found that most probably these molecules are glycosaminoglycan rather than a protein. T3 - BAM Dissertationsreihe - 34 KW - NMR KW - bones KW - organic-mineral interface KW - nanocrystalline KW - biomaterials PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1248 SN - 978-3-9812072-4-8 SN - 1613-4249 VL - 34 SP - 1 EP - 137 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-124 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Pawlowski, Kristin Helga T1 - Wirkungsmechanismen von Bisphenol-A-bis(diphenylphosphat) als Flammschutzmittel in Polycarbonat / Acrylnitril-Butadien-Styrol-Copolymerisat N2 - Die Suche nach halogenfreien Flammschutzmitteln für Polycarbonat / Acrylnitril- Butadien-Styrol-Copolymerisat (PC/ABS) führte zur Entwicklung von Triphenylphosphat (TPP), Resorcinol-bis(diphenylphosphat) (RDP) und Bisphenol-A- bis(diphenylphosphat) (BDP). Das unvollständige Wissen über die genauen Wirkungsmechanismen dieser Arylphosphate erschwert jedoch eine gezielte Optimierung der Systeme. In der vorliegenden Arbeit wurden die verschiedenen Flammschutzmechanismen von BDP in PC/ABS aufgeklärt. Ein Vergleich zwischen BDP mit RDP und TPP wurde gezogen und der Einfluss weiterer Additive wie Polytetrafluorethylen (PTFE), Böhmit, Zinkborat und Talk auf das Flammschutzverhalten von BDP herausgearbeitet. Dazu wurde das thermische Abbauverhalten mittels TG und TG-FTIR aufgeklärt. Die Entflammbarkeit wurde mit LOI- und UL 94-Tests bestimmt und das Brandverhalten anhand von Messungen im Cone Calorimeter bei unterschiedlichen Bestrahlungsstärken bewertet. Die Verbrennungsrückstände wurden mittels Festkörper-FTIR und Festkörper-NMR-Messungen charakterisiert. BDP wirkt in PC/ABS in der Gasphase durch Flammenvergiftung und in der festen Phase als Vernetzungsinitiator von PC. PTFE beeinflusst das Fließverhalten der Polymerschmelze und ermöglicht so die beste Klassifizierung im UL 94-Test von PC/ABS mit BDP. BDP ist thermisch stabiler als RDP und TPP und deshalb am aktivsten mit PC in der festen Phase. Böhmit verursacht durch eine H2O-Freisetzung Hydrolysereaktionen und wirkt somit leicht antagonistisch bezüglich der Festphasenaktivität von BDP. Zinkborat reagiert mit BDP zu alpha-Zinkphosphat und Borphosphat und unterdrückt so die Wirkung von BDP als Flammenvergifter und Vernetzungsinitiator. Die Zugabe von Talk bewirkt eine Verstärkung des Rückstandes, hat aber einen antagonistischen Effekt bezüglich der Gasphasenaktivität von BDP. Die Ergebnisse dieser Arbeit liefern ein detailliertes Verständnis der Flammschutzmechanismen von BDP und deren Abhängigkeit von der physikalischen und chemischen Umgebung. Mit diesem Wissen kann die Weiterentwicklung von BDP und anderen Arylphosphaten als Flammschutzmittel in PC/ABS gezielt optimiert werden. N2 - The search for halogen-free flame retardants for polycarbonate/acrylonitrile-butadiene- styrene (PC/ABS) has led to the development of triphenylphosphate (TPP), resorcinol bis(diphenyl phosphate) (RDP) and bisphenol A bis(diphenyl phosphate) (BDP).The lack of knowledge about the detailed flame retardant mechanisms of those arylphosphates makes it difficult to optimize those systems. In this thesis, the various flame retardancy mechanisms of BDP in PC/ABS have been clarified. BDP was compared to RDP and TPP and the influence of further additives (Polytetrafluoroethylene (PTFE), boehmite, zinc borate and talc) on the mechanisms of BDP were revealed. The thermal decomposition behaviour was clarified by means of TG and TG-FTIR. The flammability was determined by LOI and UL 94. The fire behaviour was evaluated by cone calorimeter measurements with different irradiations. Combustion residues were characterized by means of solid-state-FTIR and solid-state-NMR. BDP acts in PC/ABS as a flame inhibitor in the gas phase and as an initiator of cross linking in the condensed phase. PTFE influences the dripping behaviour of the polymer melt and enables PC/ABS + BDP to achieve the best classification in UL 94. BDP is thermally more stable than RDP and TPP and hence the most active flame retardant in the condensed phase. Boehmite releases water, which causes hydrolysis. This has an antagonistic effect concerning the condensed phase action of BDP. Zinc borate reacts with BDP to form alpha-zinc phosphate and borophosphate and suppresses the mechanisms of BDP as flame inhibitor and cross linking initiator. Talc stabilizes the char, but has an antagonistic effect on the gas phase action of BDP. The results gained from this thesis give a detailed understanding about the flame retardancy mechanisms of BDP and their dependence on the physical and chemical environment. They are fundamentals for a continuing development and improvement of aryl phosphates as flame retardants in PC/ABS. T3 - BAM Dissertationsreihe - 33 KW - PC/ABS KW - Entflammbarkeit KW - Pyrolyse KW - Acrylphosphate KW - Flammschutzmittel PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1250 SN - 978-3-9812072-3-1 SN - 1613-4249 VL - 33 SP - 1 EP - 117 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-125 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Fichera, Augusto T1 - Festkörper-NMR-Untersuchungen an thermischen Abbauprodukten von flammgeschützten Polymeren N2 - In der vorliegenden Arbeit wurden Untersuchungen an Rückständen von thermisch abgebauten, flammgeschützten Polymeren vorgenommen, mit dem Ziel, die Struktur und den Phasenbestand der eingebauten Flammschutzmittel und der Polymere sowie deren Wechselwirkungen als Funktion der Temperatur und umgebenden Atmosphäre (N2 und Luft) zu charakterisieren. Ein wichtiges Werkzeug, das Informationen über den amorphen Zustand der Abbauprodukte und deren thermisch bedingte Phasenumwandlungen in andere amorphe oder kristalline Strukturen sowie Aussagen über die Nahordnungen der betrachteten Kernspinsorte liefert, stellt in dieser Arbeit der Einsatz der Festkörper-NMR-Spektroskopie dar. Hierbei sind neben Einzelimpuls-(SP), rotor-synchronisierte Spin-Echo- (RSE) und Kreuzpolarisationstechniken (CP) auch REDOR- (Rotational echo double resonance) und TRAPDOR- (Transfer of population in double resonance) Messungen zur Anwendung gekommen. Zusätzlich konnten aus den 11B- und 31P-NMR- Experimenten quantitative Aussagen über den relativen Borat- und Phosphor bzw. Phosphat-Anteil im festen Rückstand getroffen werden, wobei insbesondere für die 31P-Kerne eine quantitative Erfassung der kristallinen und amorphen Phosphatphasen durchgeführt wurde. Im ersten System wurden die Flammschutzmittel roter Phosphor (Prot) und Mg(OH)2 in HIPS kombiniert. Aus den Ergebnissen umfangreicher NMR-Experimente konnte abgeleitet werden, dass der größte Teil des eingesetzten Prot hauptsächlich in amorphen (Mg-Ortho-, -Di-, -Ketten und Ringphosphaten) und weniger in kristallinen Phosphatphasen verbleibt. Zudem konnte für den Parameter der Temperatur und aus der Verfügbarkeit von Sauerstoff (N2-Atmosphäre/Luft) einen deutlicher Einfluss auf den Abbauprozess und die Bildung der Phosphatphasen (kristallin/amorph) nachgewiesen werden. Aus dem Vergleich der Ergebnisse der Temperversuche mit den Ergebnissen der Verbrennungsversuche im Cone Calorimeter konnte ein anaerober Abbauweg bestätigt werden. In einem zweiten System wurden die thermischen Reaktionen zwischen den Flammschutzadditiven BDP und Zinkborat sowie ihren Einfluss auf den thermischen Abbau eines PC/ABS-Blends untersucht. Der thermisch belastete Rückstand wird unabhängig von der Atmosphäre von amorphen Phosphatgruppen dominiert. Dabei konnten die während der Temperprozesse gebildeten Verbindungen α-Zn3(PO4)2 und BPO4 als Folge einer Festphasenreaktion zwischen den eingesetzten Flammschutzadditiven identifiziert werden, wobei das α-Zn3(PO4)2/BPO4 Verhältnis als Indikator für einen aeroben bzw. anaeroben Abbauprozess dient, der für die Feuerrückstände eindeutig einen anaeroben Abbau liefert. N2 - This study aims at the structural characterisation of embedded flame retardants and polymers. Analysis includes determination of the phase contents as well as description of their mutual interactions as a function of their thermal history in different atmospheres (air and nitrogen). Solid-state NMR spectroscopy is the most important tool applied in this thesis. This technique enables structural information about the amorphous state of the decomposed products, determination of the thermal and thermo-oxidative conversion in different amorphous and crystalline structures, and predictions about the short-range order of the observed nuclei. In this context measurements of single pulse (SP), rotor-synchronised spin echo (RSE) and cross polarisation (CP) experiments, as well as REDOR (Rotational echo double resonance) and TRAPDOR- (Transfer of population in double resonance) have been conducted. Additionally, 11B SP and 31P RSE experiments have been used to study quantitatively the borate and both phosphorus and phosphate contents in the solid residues. Particular emphasis was put on quantifying crystalline and non-crystalline phosphate phases. The first system consists of a combination of the flame retardants red phosphorus (Pred) and Mg(OH)2 in HIPS. From the results of extensive NMR experiments it was deduced that most of inserted red phosphorus remains in amorphous phosphates phases (ortho, pyro, and chain/ring phosphates) besides some crystalline phosphate phases. Decomposition characteristics such as temperature and the availability of oxygen (N2 atmosphere/air) show a significant influence on the decomposition process and the formation of phosphate phases (crystalline/amorphous). By comparing the results of the annealing processes to the results of the cone calorimeter measurements an anaerobic decomposition way was confirmed. In a second system, thermal reactions between the two flame retardants BDP and zinc borate as well their influence on the thermal decomposition of a PC/ABS blend were investigated. The thermally residues are independently of the atmosphere dominated by amorphous phosphate units. During the thermal decomposition the formation of α-Zn3(PO4)2 and BPO4 could be identified as solid reaction products of the inserted flame retardants. In addition, the α-Zn3(PO4)2/BPO4 ratio served as an indicator of aerobic or anaerobic decomposition processes, proving an anaerobic decomposition mechanism for the fire residues. T3 - BAM Dissertationsreihe - 32 KW - Festkörper-NMR-Spektroskopie KW - flammgeschützte Polymere KW - amorph KW - kristallin KW - Phosphor PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1260 SN - 978-3-9812072-1-7 SN - 1613-4249 VL - 32 SP - 1 EP - 153 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-126 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - McHugh, Jarlath T1 - Ultrasound Technique for the Dynamic Mechanical Analysis (DMA) N2 - The objective of this work is to demonstrate the practical application and sensitivity of ultrasound as a high frequency Dynamic Mechanical Analysis DMA technique for the characterisation of polymers. Conventional DMA techniques are used to determine thermo mechanical behaviour of polymers by typically employing dynamic shear or tensile loading modes at defined frequencies between 0.1 and 50 Hz. Sound waves may also be employed for DMA applications and depending on type of wave propagated, shear G´, G´´ and longitudinal L´, L´´ storage or loss modulus and tan (δ) may be determined from the measured acoustic parameters sound velocity and amplitude. The primary advantage of ultrasound DMA is that due to the compact sensor size it can easily be integrated into most manufacturing processes. To demonstrate the sensitivity of ultrasound to variations in the viscoelastic properties of polymers, the acoustic properties of a cured epoxy with an observed glass transition temperature of 86 °C (tan(δ) peak, 1Hz) were monitored in a temperature range from 20 to 200 °C and compared to conventional DMA results. The influence of measurement frequency, dispersion, hysteresis, reflections at material boundaries, and changes in material density on the measured sound velocity and amplitude were taken into account. To support conclusions a wide range of experimental data was evaluated using sensors operating in the frequency ranges 400 to 800 kHz and 3 to 6 MHz. The ultrasound results are compared to the tensile moduli E´, E´´ and tan(δ) measured using a conventional DMA technique operating at 0.1 to 33 Hz. Using different evaluation strategies such as the Williams Landel Ferry WLF equation it was possible to study the sensitivity of wave propagation to variations in the viscoelastic behaviour of a polymer. Taking advantage of this background knowledge, further experimental results are presented with the aim of demonstrating the sensitivity of this technique for cure monitoring applications and to the material transformations: gelation and vitrification. For this purpose an epoxy resin was cured at a range of constant temperatures whereby the curing reaction and the corresponding change in viscoelastic properties were monitored. Analysis techniques employed included ultrasound at 3 to 6 MHz, Differential Scanning Calorimeter DSC and Rheometry at 1 Hz. All results were summarised and presented graphically. Additionally an Arrhenius relationship was employed enabling direct comparison of results obtained from analysis techniques based on different working principles. Using this information, it was possible to demonstrate the practical application and the sensitivity of this technique to even small changes in viscoelastic properties of polymers. T3 - BAM Dissertationsreihe - 31 KW - Ultrasound Cure Monitoring KW - Frequency Dependence KW - Activation Energy KW - Dynamic Mechanical Analysis KW - Rheometry PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1278 SN - 978-3-9812072-0-0 SN - 1613-4249 VL - 31 SP - 1 EP - 153 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-127 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Kruschwitz, Sabine T1 - Assessment of the complex resistivity behaviour of salt affected building materials N2 - Die Art und den Grad einer Salzbelastung in feuchten Baustoffen festzustellen, gehört zu den wichtigsten und gleichfalls schwierigsten Aufgaben im Bereich der zerstörungsfreien Prüfung. Die vorliegende Arbeit beschäftigt sich mit dem möglicherweise bislang ungenutzten Potential spektraler Leitfähigkeitsmessungen und deren praktischer Anwendbarkeit. Dazu wurde erstens eine umfang- reiche Experimentreihe an unterschiedlichen Baustoffen mit vier Salzen in variierenden Konzentrationen durchgeführt, um die Sensitivität komplexer Leitfähigkeitsmessungen der für den Baubereich relevanten Salzmengen zu untersuchen. Zweitens wurde der Einfluß der Sättigung für verschiedene Ausgangsfluide nachvollzogen, da Feuchteschäden häufig räumlich begrenzt sind und sich in ihrer Stärke verändern. Da das spektrale Leitfähigkeitsverhalten allerdings ein Wechselspiel verschiedener Stoffeigen-schaften ist, beschäftigt sich diese Arbeit darüber hinaus auch mit dem Versuch, chemisch von strukturell bedingten Impedanzänderungen unterscheiden zu lernen. In einer Finite Differenzen Modellierung wurden die effektiven Impedanzen synthetischer Mikrostrukturen berechnet und die Auswirkungen von Strukturunterschieden untersucht. Die komplexen elektrischen Eigenschaften wurden generell im Frequenzbreich 1 mHz -100 Hz bestimmt. Als Schadsalze wurden NaCl, Na2SO4, CaCl2 und MgSO4 verwendet. Da elektrische Verfahren Wasser und Salz nicht direkt, sondern indirekt über den Widerstand messen, sind a-priori Informationen bei der Auswertung erforderlich. Liegen Kalibrations-daten vor, kann im Fall eines vollständig gesättigten Baustoffes allein anhand der (realen und einfachmessbaren) Widerstandsamplitude eine verlässliche Einschätzung des Salzgehaltes vorgenommen werden. Die Phase des komplexen elektrischen Widerstands enthält Informationen über den Charakter (Wertigkeit) des dominanten Kations in der Porenfluidlösung. In porösen, feuchten Baustoffen, in denen Polarisation als Folge komplexer Grenzflächenleitfähigkeit auftritt, bestimmen generell das Matrixmaterial, der Porendurchmesser und die innere Oberfläche seine Aufladbarkeit. Die Ergebnisse der vorliegenden Arbeit zeigen jedoch deutlich, daß diese Größen nur bedingt aus elektrischen Messungen abgeleitet werden können. Liegt die durchschnittliche Porenhalsgröße eines Baustoffs zwischen 20 und 100 μm, kann in der Regel eine deutliche Aufladbarkeit im untersuchten Frequenzbereich beobachtet werden. In feinporigen Baustoffen wie den meisten Tonziegeln sind die dominaten Porenhalsgrößen kleiner als 5 μm, und die Aufladbarkeit liegt oft nur noch im Bereich der Messgenauigkeit. Generell können material und fluidbedingt verschiedene Arten von Widerstands- /Frequenzverhalten beobachtet werden. Für solche Baustoff, die ein Cole-Cole (C-C) Relaxationsverhalten zeigen, wird beobachtet, dass die Relaxationszeit τ und ebenfalls die Magnitude des Phasenmaximums mit zunehmendem Porenhalsdurchmesser abnehmen. Die hier vorgestellte Datenbasis untermauert den theoretisch vorhergesagten exponentiellen Zusammenhang zwischen τ und einer materialbedingten, charakteristischen Relaxationslänge - im Fall von Festmaterialien der Porenhalslänge. In der Salinitätsstudie konnte nachgewiesen werden, wie sensitiv die Polarisierbarkeit (Imaginärteil der Leitfähigkeit) auf die Ionenkonzentration und sogar die Art der im Fluid enthaltenen Ionen reagiert. Ausschlaggebend sind wahrscheinlich Veränderungen in der elektrischen Doppelschicht (EDL) hinsichtlich ihrer Geometrie und chemischen Zusammensetzung. Der Imaginärteil der elektrischen Leitfähigkeit steigt für die meisten Baustoffe bis zu Fluidleitfähigkeiten von 1 S/m an. Dies liegt wahrscheinlich an der fortschreitenden Ionensättigung des EDL. Ist eine gewisse Sättigungsstufe erreicht, führt eine weitere Ionenzufuhr zu zunehmenden elektrostatischen Wechselwirkungen und schließlich abnehmenden Ionendiffusionskoeffizienten. Die experimentellen Befunde dieser Arbeit weisen auch den Einfluß des Durchfeuchtungs-grades auf die komplexen Leitfähigkeitseigenschaften deutlich nach. Für die meisten Baustoffe nimmt mit dem Wassergehalt der Imaginärteil der Leitfähigkeit stärker ab als der Realteil. Unabhängig von der Art des Porenfluids und obwohl die Leitfähigkeit des Poren-fluids während der evaporativen Trocknung zunahm, lagen die Sättigungsexponenten des Imaginärteils in der Regel doppelt so hoch wie die des Realteils. Es deutet sich im Vergleich dieser Daten mit den Beobachtungen anderer Autoren an, daß der Tongehalt und möglicherweise der Zementationsgrad eines Materials ausschlaggebend für ein solches, nicht der bisherigen Theorie entsprechendes Verhalten sind. Darüber hinaus wurde beobachtet, daß die Position des Phasenmaximums im Frequenzbereich und damit die C-C Relaxationszeit für einige Baustoffe zu-, für andere abnahm und für wieder andere der Phasenpeak schnell ganz abflachte. Diese Ergebnisse zeigen deutlich, daß der kürzlich von anderen Autoren aufgezeigte Zusammenhang von C-C Relaxationszeit und hydrau-lischen Eigenschaften (Permeabilität) zumindest nicht bedingungslos gültig ist und weiterer Forschungsbedarf besteht. Um die Eigenschaften der elektrischen Doppelschicht in Abhängigkeit der Porenfluidchemie zu untersuchen, wurden Zetapotentialmessungen durchgeführt sowie mittels Autotitration Oberflächen- ladungsdichten ermittelt. Die verwendeten Partikelsuspensionen wurden in gleicher Weise mit den Schadsalzen versetzt wie zuvor die Baustoffproben in den elektrischen Messungen. Die Auswertung der elektroakustischen Messungen deutet zwar generell einen positiven linearen Zusammenhang zwischen Zetapotential und dem Imaginärteil der Leitfähigkeit an, dieser ist jedoch schwächer als erwartet. Eine ausgeprägte Abhängigkeit der imaginären Leitfähigkeit konnte nur in einem Fall nachgewiesen werden, nämlich für den sehr tonhaltigen Cottaer Sandstein. In der einschlägigen Literatur wird davon ausgegangen, daß die komplexen elektrischen Eigen- schaften eines Materials außer vom Chemismus der elektrischen Doppelschicht auch von der Geometrie des Porenraumes in einem Material bestimmt werden. In einem neuartigen Versuch, diese beiden Phenomäne zu trennen, wurde eine Parameterstudie mittels einer FD-Impedanzmodellierung durchgeführt, in der gezielt Längenverhältnisse und Leitfähigkeiten verändert werden konnten. Es wurde grundsätzlich von einem Dreiphasensystem aus Matrix, elektrischer Doppelschicht und Fluid ausgegangen. Eine Erhöhung der Salzfracht in der Fluidphase bewirkt zum einen eine Zunahme der Fluid-leitfähigkeit und zum anderen eine Abnahme der Doppelschichtmächtigkeit. Beide Vorgänge hatten in der Modellierung zur Folge, daß das Phasenmaximum abnahm und sich zu höheren Frequenzen verschob. Dies wurde auch für die Mehrheit der Baustoffe in der experimentellen Arbeit beobachtet. Nur im Fall des Cottaer Sandstein verschob sich das Phasenmaximum mit zunehmender Fluidsalinität zu niedrigeren Frequenzen; möglicher-weise findet hier eine chemische Umstrukturierung (Ionenaustauschvorgänge) statt, die abhängig von der Art und dem Gehalt der Tonfraktion und dem Chemismus des Porenfluids sein könnten. Die Beobachtungen der Entsättigungsexperimente konnten ebenfalls mit der effektiven Impedanzmodellierung nachvollzogen werden. Falls die hier verwendeten, stark vereinfachten, synthetischen Modelle die komplexen elektrischen Eigenschaften wahrheitsgemäß abbilden, bieten sie die Möglichkeit eines erweiterten Verständisses des Leitfähigkeitsverhaltens teilgesättigter Medien. Komplexe Widerstandsmessungen bieten also durchaus Potential für die Anwendung im Bereich der zerstörungsfreien Bauwerksanalyse, es handelt sich zum gegenwärtigen Zeitpunkt jedoch noch um eine Methode im Forschungsstadium. Die Aussagekraft und Anwendbarkeit des Verfahrens variiert stark mit der durchschnittlichen Porengröße, dem Durchfeuchtungsgrad und der Salzfracht des Untersuchungsobjekts. In jedem Fall sind a-priori Informationen und -sofern quantitative Aussagen getroffen werden sollen- auch Kalibrationsdaten erforderlich. Das Verfahren sollte nicht allein angewendet werden. Um quantitativ Salzgehalte zu bestimmen, muß die Materialfeuchte bekannt sein und vice versa. Zuverlässiger wird die Interpretation, wenn die Art des Schadsalzes (oder Fluids, z.B. Regenwasser oder Leitungswasser) bekannt ist. Weitere, leicht kontrollierbare Laboruntersuchungen sind letztlich notwendig, um ein umfassenderes Model der Polarisationsvorgänge in der elektrischen Doppelschicht zu entwickeln. N2 - The ability to reliably predict the amount and type of salts within a wet masonry is one of the most important and challenging subjects in the field of non-destructive combat of salt attack and preserving buildings and monuments of historical or archaeological value. To investigate the potential value of complex resistivity (CR) measurements for the early detection of salt and moisture related stone altering, a controlled salt type and concentration experiment series has been performed and a new procedure of an image based effective impedance modelling developed. Complex resistivity magnitude and phase measurements in the frequency range of 1 mHz to 100 Hz were acquired on a wide variety of wholly and partially brine saturated building stone samples. Deteriorating agents NaCl, Na2SO4, CaCl2 and MgSO4 were used. Since water and salt are not measured directly, the method is incapable of deducing possible building damages lacking a priori information. In the case of saturated materials, and provided thorough calibration data are available, a reliable estimate of salt concentration is possible from the measured resistivity magnitude. Additional indication on the dominant cation in the solution can be obtained from the measured resistivity phase, which is significantly higher the lower its valency. Furthermore, the measurements reported in this study give an important guide to the limitations of CR in obtaining pore surface area and pore throat estimates. For wet porous materials, in which polarization occurs due to complex surface conduction, the dominant pore throat and amount of specific surface affect its polarizability. Sandstones, sand-limestones and aerated concretes are more qualified observation objects (pore throats between 20 and 100 μm), whereas for bricks (pore sizes often < 5 μm) the method seems far less favorable. For those materials, which exhibit a Cole-Cole (C-C) type of relaxation, the phase peak is observed to decrease significantly with pore throat size and to occur at higher frequencies. The predicted power-law correlation between the C-C relaxation time and characteristic length scale (pore throat size for consolidated materials) is supported by the presented data. The experimental salinity study reveals how responsive polarization (in terms of imaginary conductivity) is to changing the ionic concentration or composition of the pore fluid. The properties of the electrical double layer and particularly its chemical composition are most likely the crucial controlling factors. The imaginary conductivity is observed to increase for most materials up to fluid salinities of about 1 S/m - a fact, that may be attributed to a mechanism of ion saturation within the electrical double layer; further ion supply seems to counteract this leading to ion-ion interactions, which decrease ionic mobility. CR measurements on partially saturated samples demonstrate the method’s sensitivity to water content. For most materials the imaginary conductivity component decreased significantly faster than the real component. Independent of the pore fluid and even though its salinity naturally increased during the evaporative drying procedure, the normalized saturation exponent of the quadrature component was about twice as high as the real one especially for clay-rich sandstones. The results revealed diverse behavior such as decreases and increases in relaxation time with saturation. In some cases a suppression of a distinctive relaxation curve at low saturations was observed. The results indicate, that contrary to conclusions from recent related studies, the correlation between a C-C relaxation time and hydraulic properties may be limited. In order to infer information on the charge distributions within the EDL, zeta-potentials and surface charge densities were obtained from electroacoustic measurements on particle suspension containing the same amounts and types of salt like used in the brine saturation CR study. The results add weight to the assumption that there is some universal positive relationship between zeta-potential and imaginary conductivity. A notable dependence of imaginary conductivity on diffuse layer surface charge was only observed in case of one sandstone (Cottaer), this being the material with the most abundant clay content. An image based effective impedance modelling approach revealed the fact that, even though it is not able to factor scale effects in, it is helpful to study general microstructural implications on CR responses. It was observed, that an increasing salt concentration (that creates a shrinking electrical double layer) reduces the peak phase and moves it towards higher frequency. The same effect would have an increasing fluid conductivity for a otherwise fixed microstructure. For some combinations of material and salt, however, in the experimental work the peak phase was observed to shift towards lower frequency: a phenomenon that could not be explained with the modelling. Therefore, it is assumed that chemical properties, like ion mobilities or other surface chemistry properties (ionexchange processes) must be regarded to conclusively explain surface conductivity mechanisms. Other experimental observations like the alteration of CR spectra at desaturation could likewise be modelled. If these models truly mimic the effective electrical properties, the results give new implications on the effective medium behavior. Concluding, the author values the complex resistivity method as a possible effective non-destructive testing (NDT) tool for a wide range of building stones. Depending on pore size and saturation important additional information can be obtained. In all cases, a priori information and calibration data are essential, that is, CR should not be treated as a stand-alone method. Further measurements are needed to develop a more complete model of the electrical double layer and its alteration with changing salinity and ion types. T3 - BAM Dissertationsreihe - 30 KW - salt KW - FD-Impedanzmodellierung KW - Baustoffe KW - Feuchte KW - Salz KW - Spektral Induzierte Polarisation KW - building materials KW - Complex resistivity KW - moisture KW - FD impedance modelling PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1287 SN - 978-3-9811655-9-3 SN - 1613-4249 VL - 30 SP - 1 EP - 179 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-128 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Burkert, Andreas A1 - Mietz, Jürgen A1 - Lehmann, Jens A1 - Eich, Gerd A1 - Burkert, Annette T1 - Verzinkte Bauteile in Kontakt mit Spanngliedern N2 - Um zu klären unter welchen Umständen eine Gefährdung von Spannstählen beim Kontakt mit verzinkten Bauteilen gegeben ist, wurden umfangreiche Laborversuche in alkalischen Lösungen und verschiedenen Betonen sowie Zeitstandversuche an Spannbetonprobekörpern durchgeführt. Dabei zeigte sich, dass Abstandsvariationen im Nahbereich nur einen geringen Einfluss auf die Polarisation des Stahles haben. Ein praxisrelevanter, unkritischer Abstand für den indirekten Kontakt des Spannstahls, z. B. über die Bewehrung, konnte daher nicht definiert werden. Aus den Versuchsreihen wurde deutlich, dass ein wesentlicher Einfluss durch das Flächenverhältnisses Stahl: Zink gegeben ist. Hier konnte eine praxisrelevante Grenze ermittelt werden. Danach führen Flächenverhältnisse größer 10 : 1 nicht zu einer Polarisation des Spannstahls in den Bereich der Wasserstoffentwicklung. Die im Labor gewonnen Ergebnisse konnten durch Untersuchungen zunächst an realen Betonfertigteilen, später auch an Spannbetonfertigteilen bei der Fa. Rekers verifiziert werden. Auf der Grundlage dieser Untersuchungen wurde für eine spezielle Spannbetonbinderausführung, bei der die Flächenverhältnisse in unkritischen Breichen lagen, für die Verwendung von verzinkten Einbau- teilen im indirekten Kontakt mit Spannstählen eine Zustimmung im Einzelfall gegeben. Während der Vorhabensbearbeitung wurde von den beteiligten Firmen eine weitere Problematik angesprochen. Dabei ging es um den Einsatz von verzinkten Einbauteilen in Spann- betonfertigteilen aus Stahlfaserbeton. Auch hier war die Frage, ob eine Gefährdung der Spannstähle durch indirekten Kontakt über die nicht verzinkten Stahlfasern möglich ist. Durch Untersuchungen an realen Fertigteilabschnitten bei den Firmen Rekers und Max Bögl konnte gezeigt werden, dass ein Kontakt über die Stahlfasern selbst über sehr kurze Entfernungen nicht vorliegt. Auf der Grundlage dieser Ergebnisse wurden für derartige Fertigteile beim Deutschen Institut für Bautechnik entsprechende bauaufsichtliche Zulassungen unter Verwendung verzinkter Einbauteile beantragt. Um eine sichere Gefährdungsabschätzung bei indirektem Kontakt für Flächenverhältnisse vornehmen zu können, bei denen eine Polarisation der Spannstähle in den Bereich der Wasserstoffentwicklung erfolgt, wurden Zeitstandversuchsreihen unter Wasserstoffbeladung durchgeführt. Diese führten an zugelassenen Spannstählen nicht zu Brüchen während der Versuchszeit. Die anschließend ermittelten mechanischen Kennwerte zeigten keine signifikanten Änderungen. Aus den Ergebnissen dieser Untersuchungen, die bezüglich der Bela- dungsmenge, der Beladungszeiten und der gewählten Vorspannung sehr konservativ ausgelegt wurden, ist ein indirekter Kontakt von Spannstählen zu verzinkten Einbauteilen als unkritisch zu bewerten. Eine entsprechende Änderung der Norm ist anzustreben. Aus grundsätzlichen Gründen der direkte Kontakt durch Einhaltung des in der DIN 1045-1 geforderten Mindestabstandes von 2 cm aber weiterhin sicher auszuschließen. Dies stellt für die Anwender aus praktischer Sicht kein Problem dar. Durch die in enger Zusammenarbeit mit der Industrie durchgeführten Forschungsarbeiten wird es den Anwendern ermöglicht, zukünftig verzinkte Einbauteile in Spannbetonfertigteilen einzusetzen. Teilweise konnte der Einsatz durch Zustimmungen im Einzelfall bzw. durch bauaufsichtliche Zulassungen bereits unmittelbar in der Praxis umgesetzt werden. Damit wurde das Ziel des Vorhabens erreicht. T3 - BAM Forschungsberichtreihe - 282 PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1695 SN - 978-3-9812072-6-2 SN - 0938-5533 VL - 282 SP - 1 EP - 28 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-169 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 38, Heft 4 T3 - Amts- und Mitteilungsblatt der BAM - 4/2008 PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-256 SN - 0340-7551 VL - 38 IS - 4 SP - 1 EP - 262 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-25 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 38, Heft 3 T3 - Amts- und Mitteilungsblatt der BAM - 3/2008 PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-268 SN - 0340-7551 VL - 38 IS - 3 SP - 1 EP - 354 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-26 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 38, Heft 2 T3 - Amts- und Mitteilungsblatt der BAM - 2/2008 PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-277 SN - 0340-7551 VL - 38 IS - 2 SP - 1 EP - 58 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-27 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 38, Heft 1 T3 - Amts- und Mitteilungsblatt der BAM - 1/2008 PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-287 SN - 0340-7551 VL - 38 IS - 1 SP - 1 EP - 86 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-28 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Akkerman, Floris T1 - Nur ein Watt für Standby-Betrieb - Ökodesign-Richtlinie der EU legt Grenzwerte für Elektrogeräte fest KW - Standby-Betrieb KW - Ökodesign KW - EBPG PY - 2008 SN - 1866-1335 VL - 1 IS - 6 SP - 36 EP - 38 PB - Publ.-Industry-Verl. CY - München AN - OPUS4-27960 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eliezer, Dan A1 - Böllinghaus, Thomas T1 - Hydrogen trapping mechanisms in structural materials T2 - Effects of hydrogen on materials - 2008 International hydrogen conference CY - Jackson, Wyoming, USA DA - 2008-09-07 PY - 2008 SN - 1615030034 SP - 438 EP - 447 PB - ASM international AN - OPUS4-24543 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böllinghaus, Thomas A1 - Wongpanya, Pornwasa T1 - Modeling of hydrogen assisted cold cracking in high strength steel welds T2 - Effects of hydrogen on materials - 2008 International hydrogen conference CY - Jackson, Wyoming, USA DA - 2008-09-07 PY - 2008 SN - 1615030034 SP - 588 EP - 595 PB - ASM international AN - OPUS4-24544 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wolf, Martin A1 - Kannengießer, Thomas A1 - Böllinghaus, Thomas ED - Carl E. Cross, ED - John C. Lippold, ED - Böllinghaus, T. ED - Herold, H. T1 - Determination of critical strain rate for solidification cracking by numerical simulation PY - 2008 SN - 978-3-540-78627-6 IS - Part I SP - 77 EP - 92 PB - Springer CY - Berlin AN - OPUS4-24488 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Martin, Tina T1 - Spektrale Induzierte Polarisation (SIP) – Anisotropienachweis an Holz T2 - 68. Jahrestagung der Deutschen Geophysikalischen Gesellschaft (DGG) CY - Freiberg, Germany DA - 2008-03-03 PY - 2008 AN - OPUS4-25017 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Herm, C. A1 - Krug, Sonja A1 - Mazurek, J. A1 - Schilling, M. T1 - Giovanni Ambrogio Bevilacqua 'Maria, das Kind anbetend' - painting material analysis PY - 2008 SN - 0931-7198 VL - 22 IS - 1 SP - 20 EP - 26 PB - Werner CY - Worms AN - OPUS4-27537 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dmitriev, A.I. A1 - Österle, Werner A1 - Kloß, Heinz T1 - Numerical simulation of typical contact situations of brake friction materials N2 - In the paper, a model typical for contact situations of automotive brakes is established based on the method of movable cellular automata. The processes taking place at local contacts in an automotive brake system are analysed. Based on microscopic and micro-analytical observations, the following contact situations were simulated: (i) a couple of ferritic steel against pearlitic steel, both covered by an oxide layer mixed with graphite nanoparticles and (ii) the same situation but without oxide layers. The results of calculated mean coefficients of friction of the oxide-on-oxide contact correspond well to expected values for a real braking system, whereas steel-on-steel contact are twice as high. This allows one to make some conclusions; for example, oxide formation will take place more quickly than friction layer elimination, and finally this is responsible for the stabilisation of the coefficient of friction. KW - Friction KW - Primary contact KW - Automotive brake system KW - Numerical simulation KW - Method of movable cellular automata PY - 2008 DO - https://doi.org/10.1016/j.triboint.2007.04.001 SN - 0301-679X VL - 41 IS - 1 SP - 1 EP - 8 PB - Butterworth-Heinemann CY - Oxford AN - OPUS4-15841 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ploska, Ute A1 - Berger, Georg A1 - Jörn, Daniela A1 - Willfahrt, Manfred A1 - Hackbarth, Andreas T1 - Calcium titanate reaction layers on TiAl6V4 implants KW - Titan alloy KW - Calcium titanate KW - Reaction layer KW - Implant PY - 2008 SN - 1013-9826 VL - 361-363 SP - 657 EP - 660 PB - Trans Tech Publ. CY - Aedermannsdorf AN - OPUS4-15899 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bernstein, A. A1 - Nöbel, D. A1 - Mayr, H.O. A1 - Gildenhaar, Renate A1 - Berger, Georg A1 - Ploska, Ute A1 - Brandt, J. T1 - Influence of Calcium Zirconium Phosphate Containing Coatings on Mineralization of Bone KW - Ceramics KW - Coating KW - Biomaterial KW - Bone KW - Biocompatibility KW - Surface reaction PY - 2008 SN - 1013-9826 VL - 361-363 SP - 641 EP - 644 PB - Trans Tech Publ. CY - Aedermannsdorf AN - OPUS4-15900 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Beranic Klopcic, S. A1 - Pribosic, I. A1 - Kosmac, T. A1 - Ploska, Ute A1 - Berger, Georg T1 - The Reactivity of CaTi4(PO4)6 with Alumina and Y-TZP Ceramics KW - Calcium titanium phosphate KW - Alumina KW - Zirconia PY - 2008 SN - 1013-9826 VL - 361-363 SP - 787 EP - 790 PB - Trans Tech Publ. CY - Aedermannsdorf AN - OPUS4-15901 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gildenhaar, Renate A1 - Berger, Georg A1 - Lehmann, Erhard A1 - Knabe, C. T1 - Development of Alkali Containing Calcium Phosphate Cements KW - Calcium phosphate cement KW - Calcium potassium sodium phosphate KW - Potassium containing apatite KW - Bone substitute materials PY - 2008 SN - 1013-9826 VL - 361-363 SP - 331 EP - 334 PB - Trans Tech Publ. CY - Aedermannsdorf AN - OPUS4-15902 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beck, Uwe A1 - Hertwig, Andreas A1 - Krüger, Jörg T1 - Material-, topgraphy- and feature recognition: Challenges on optical property testing of surfaces and thin films T2 - 35th International Conference On Metallurgical Coatings And Thin Films (ICMCTF 2008) CY - San Diego, CA, USA DA - 2008-04-28 PY - 2008 AN - OPUS4-15880 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schiller, Wolfgang Arno T1 - Keramische Multilayer für Mikrosysteme im Bereich Sensorik, Biomedizin und Energietechnik T2 - Symposium "Vision Keramik 2008++" CY - Dresden, Germany DA - 2008-01-17 PY - 2008 AN - OPUS4-15870 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Figiel, L. A1 - Günther, Burkhard T1 - Modelling the high-temperature longitudinal fatigue behaviour of metal matrix composites (SiC/Ti-6242): Nonlinear time-dependent matrix behaviour N2 - The purpose of this work is modelling of the behaviour of a metal matrix (Ti-6242) that governs the nonlinear time-dependent response of the metal matrix composite (SiC/Ti-6242). For this purpose two different viscoplastic constitutive models are applied. First, it is the two-layer viscoplasticity model available in the finite element method (FEM)-based code ABAQUS. Second, it is the model of Chaboche implemented as a user material subroutine into another FEM-based code ANSYS and additionally into the package Mathematica. Parameters of both the models are obtained based on the available results of experimental tests carried out at different temperatures and strain rates. Utilisation of matrix models for simulation of the thermomechanical fatigue behaviour of the undamaged composite is discussed by a comparison with quasi-static tensile and high-temperature creep experimental tests. KW - Metal matrix composites (SiC/Ti-6242) KW - Thermomechanical fatigue behaviour KW - Viscoplastic constitutive models KW - Finite element method PY - 2008 DO - https://doi.org/10.1016/j.ijfatigue.2007.01.056 SN - 0142-1123 VL - 30 IS - 2 SP - 268 EP - 276 PB - Elsevier CY - Oxford AN - OPUS4-16284 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bässler, C. A1 - Stülpnagel, H. A1 - Ehreke, Jörg T1 - Ständiges Lernen ist das Ziel PY - 2008 SN - 0720-1214 SN - 0033-5126 VL - 53 IS - 1 SP - 2 EP - 4 PB - Hanser CY - München AN - OPUS4-16324 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zencker, Uwe A1 - Qiao, Linan A1 - Wieser, Günter A1 - Völzke, Holger T1 - Numerische Analyse eines ungedämpften Behälterabsturzes aus 0,3 m Höhe T2 - Jahrestagung Kerntechnik 2008 CY - Hamburg, Germany DA - 2008-05-27 PY - 2008 AN - OPUS4-16329 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Wolff, Dietmar A1 - Drottleff, H. A1 - Hinterding, P. T1 - Die Koordinierungsstelle für Informationen zur Behälterabfertigung (KOBAF): Aufgaben und Erfahrungen T2 - Jahrestagung Kerntechnik 2008 CY - Hamburg, Germany DA - 2008-05-27 PY - 2008 AN - OPUS4-16330 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Meng, Birgit A1 - Fontana, Patrick A1 - Müller, Urs T1 - Nanotechnologie im Beton - Entwicklungsstand und Innovationschancen KW - Nanotechnologie KW - Analytik KW - Gefüge KW - Zement KW - Beton PY - 2008 SN - 978-3-7625-3624-6 VL - 56 SP - 186 EP - 190 PB - Bauverlag BV CY - Gütersloh AN - OPUS4-16316 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Lehmann, Jens T1 - Damit Edelstahl rostfrei bleibt - Korrosionsschutzgerechte Verarbeitung von Edelstahl Rostfrei T2 - Jahrestagung DVS Bezirksverband Riesa - Meißen - Großenhain CY - Dresden, Germany DA - 2008-03-01 PY - 2008 AN - OPUS4-16703 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Lehmann, Jens T1 - Edelstahl rostfrei - Korrosionsverhalten und Schadensvermeidung T2 - Praxisseminar "Fachgerechte Auswahl und Verarbeitung von Edelstahl Rostfrei", DVS Bezirksvorstand Ostwestfahlen-Lippe CY - Bielefeld, Germany DA - 2008-03-07 PY - 2008 AN - OPUS4-16704 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Lehmann, Jens T1 - Damit Edelstahl rostfrei bleibt - Korrosionsschutzgerechte Verarbeitung von Edelstahl Rostfrei T2 - Praktikertagung im Metallhandwerk, Handwerkskammer Regensburg CY - Regensburg, Germany DA - 2008-02-27 PY - 2008 AN - OPUS4-16705 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schalau, Bernd A1 - Groh, B. T1 - Praktische Beispiele und Erfahrungen zu Störfallauswirkungsbetrachtungen - Freistrahlberechnungen - T2 - Sicherheitstechnischer Erfahrungsaustausch, Landesanstalt für Umwelt, Messungen und Naturschutz CY - Karlsruhe, Germany DA - 2008-04-22 PY - 2008 AN - OPUS4-16706 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Franke, Werner T1 - Das Zusammenladen und die gemeinsame Beförderung von Sprengstoffen und Zündmitteln auf öffentlichen Straßen unter Einbeziehung von in diesem Zusammenhang durchgeführten Versuchen der Bundesanstalt für Materialforschung und -prüfung T2 - 30. Informationstagung Sprengtechnik CY - Siegen, Germany DA - 2008-03-28 PY - 2008 AN - OPUS4-16707 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bösel, Dieter A1 - Baer, Wolfram A1 - Eberle, Arno A1 - Klingbeil, Dietmar T1 - Stand der Entwicklung von Key Curve Einprobenverfahren zur Ermittlung dynamischer Risswiderstandskurven an duktilen Gusseisenwerkstoffen KW - Dynamische Bruchmechanik KW - Risswiderstandskurve KW - Einprobentechnik KW - Gusseisen mit Kugelgraphit KW - Dynamic fracture mechanics KW - Crack resistance curve KW - Single specimen method KW - Ductile cast iron PY - 2008 SN - 1616-4687 SP - 73 EP - 81 AN - OPUS4-16709 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Österle, Werner A1 - Klaffke, Dieter A1 - Griepentrog, Michael A1 - Gross, U. A1 - Kranz, I. A1 - Knabe, Ch. T1 - Potential of wear resistant coatings on Ti-6Al-4V for artificial hip joint bearing surfaces N2 - Tribological screening tests (simple, reciprocating ball-on-flat tests) were performed with the objective to identify an appropriate coating for the articulating surfaces of artificial hip joints whose acetabular cups and femoral stems are made from Ti–6Al–4V alloy, which is appreciated for its light weight, good biocompatibility and elastic properties similar to those of natural bone. Standard coatings like TiN or CrN performed better than more complicated multi-layer systems, though not as good as different types of amorphous carbon coatings, generally referred to as diamond-like carbon or DLC coatings. Among the latter, hydrogenated amorphous carbon (a-C:H) displayed the best properties, especially if the hydrogen content was increased by reducing the bias voltage during PA-CVD-deposition. The optimised a-C:H coating revealed the most promising wear behaviour under the applied testing conditions, i.e. the increase of linear wear with the number of cycles was close to zero. Regarding the materials examined in this study, correlation of wear with mechanical properties obtained by nano-indentation revealed that high hardness was not an adequate criterion for selecting appropriate coatings. A high ratio of hardness and elastic modulus (H/E) proved to be more important. Microstructural and micro-analytical investigations revealed transformation of TiN and CrN to TiO2 and Cr2O3, respectively, and amorphous carbon was, at least partly, transformed to graphite. Furthermore, incorporation of Al2O3 from the ball was observed at a very fine scale. The wear debris of favourable coatings always formed agglomerates of nano-scale particles. It was shown that commercial nano-particles of Al2O3, Cr2O3 and carbon black are comparable to particles generated by the tribological tests. However, it is uncertain whether they are comparable to those formed during simulator studies or in vivo. Furthermore, the performance of the favourable coating has to be tested in a hip joint simulator before its potential for application in prostheses can be assessed. KW - Coating KW - Implant KW - Titanium alloy KW - DLC KW - Wear debris KW - Nano-particles PY - 2008 DO - https://doi.org/10.1016/j.wear.2007.04.001 SN - 0043-1648 VL - 264 IS - 7-8 SP - 505 EP - 517 PB - Elsevier CY - Amsterdam AN - OPUS4-16711 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Franke, Werner T1 - Zusammenladen von Sprengstoffen und Zündmitteln auf einem Fahrzeug N2 - Die Wirksamkeit einer Abtrennung aus Holz mit mindestens 50 mm Wandstärke für Zündmittel der Klassifizierung 1.4B konnte überzeugend bestätigt werden. Außerhalb dieser Abtrennung war überhaupt keine Wirkung zu beobachten. Auch wenn die Originalverpackung leichterer Bauart vergleichsweise stark beschädigt wurde fungierte die hölzerne Abtrennung aus wirksamer Schutz gegen die entstandenen Splitter. Einer weiteren Anwendung der bisherigen Verfahrensweise steht aus sicherheitstechnischer Sicht nichts im Wege. KW - ADR KW - RID KW - Massenexplosive - nicht massenexplosive Zündmittel KW - Schutzbehälter KW - Detonationsübertragung auf Sprengstoff PY - 2008 SN - 0941-4584 VL - 30 IS - 1 SP - 15 EP - 18 PB - Deutscher Sprengverband CY - Siegen AN - OPUS4-16712 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Simone A1 - Wachtendorf, Volker A1 - Rauth, W. A1 - Klimmasch, T. A1 - Krüger, P. T1 - Screening the weathering stability of automotive coatings by chemiluminescence N2 - Chemiluminescence (CL) is a sensitive method of investigating the thermo-oxidative stability of polymers in the early stages of degradation. Therefore, CL measurements were applied to different automotive coatings to evaluate their degradation behavior during artificial weathering. In this work, CL measurements were carried out for different automotive coatings to follow their degradation behavior during artificial weathering. The CL emission depends on sample-specific parameters like stabilizer, matrix, or hardener; experimental parameters like the oxygen partial pressure; and exposure parameters like the duration of weathering. The potential of CL could be demonstrated by classifying materials into categories of good, medium, and low degradation performance at a much earlier stage of weathering exposure than in combination with the usual visual detection of weathering effects. KW - Accelerated weathering KW - Coating KW - Chemiluminescence KW - Sensitive detection KW - Weathering PY - 2008 DO - https://doi.org/10.1007/s11998-007-9071-7 SN - 1547-0091 SN - 1935-3804 VL - 5 IS - 1 SP - 17 EP - 24 PB - Springer CY - Blue Bell, Pa. AN - OPUS4-16723 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mietz, Jürgen A1 - Burkert, Andreas A1 - Lehmann, Jens A1 - Burkert, Annette A1 - Eich, Gerd T1 - Galvanised constructional elements in contact with prestressing steel tendons N2 - In order to clarify under which practical conditions real risks for hydrogen-induced stress corrosion cracking of prestressing steels exist laboratory investigations in aqueous solutions and concrete as well as tests with stressed prestressing steels were carried out. While different distances between steel and zinc (cathode and anode) showed only a negligible influence on the polarisation of the steel a significant dependence on the area ratio steel/zinc was observed. A critical area ratio of 10:1 can be defined above which polarisation of the steel to hydrogen evolution potentials is unlikely. The results obtained in the laboratory concerning the critical area ratio were confirmed by on-site investigations in a precasting plant. Exposure tests with hydrogen loading did not lead to fractures during the testing time for approved prestressing steels. The characteristic mechanical values determined immediately after the hydrogen loading tests did not show significant changes. Thus, an indirect contact between prestressing steels and galvanised elements can be estimated as uncritical. But a direct contact has to be excluded by compliance with DIN 1045-1, i.e minimal distance of 2 cm between prestressing steel and galvanised elements. PY - 2008 DO - https://doi.org/10.1002/maco.200804114 SN - 0947-5117 SN - 1521-4176 VL - 59 IS - 2 SP - 131 EP - 138 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-16724 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Recknagel, Christoph A1 - Goebbels, Jürgen A1 - Meinel, Dietmar T1 - Möglichkeiten der Strukturkennzeichnung von Asphalten mittels 3D-Computertomographie N2 - Die Struktur eines Materials bestimmt wesentlich dessen Gebrauchsverhalten. Diese einfache Weisheit ist Motivation für die ständige Weiterentwicklung des Untersuchungsinstrumentariums zur Gefügekennzeichnung von Baustoffen. Nachdem die Gefügeaufklärung insbesondere bei mineralischen Baustoffen bereits integrierter Bestandteil der Baustoffcharakterisierung ist, erhöht insbesondere die zunehmende Spezialisierung und Weiterentwicklung der Asphaltbaustoffe zusammen mit der Forderung nach gebrauchsgerechtem Leistungsnachweis den Bedarf an methodischer Entwicklung bei der Strukturkennzeichnung. Besondere Möglichkeiten zur tiefenaufgelösten und zerstörungsfreien räumlichen Visualisierung des Gefüges, der Ableitung strukturbeschreibender Kennwerte aber auch für eine anschließende Diskretisierung der inneren Struktur mittels finiter Elemente bietet das Verfahren der Computertomographie mit Röntgenstrahlen. Mit Hilfe verschiedener Anwendungen soll auf die Möglichkeiten dieser Methodik aufmerksam gemacht werden. KW - Innere Struktur KW - Asphalte KW - Hohlraumgehalt und -verteilung KW - Phasenanalyse KW - Strukturelle Artefakte PY - 2008 SN - 0039-2162 VL - 2 SP - 65 EP - 74 PB - Kirschbaum-Verl. CY - Bonn-Bad Godesberg AN - OPUS4-16725 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Müller, Urs A1 - Meng, Birgit A1 - Kühne, Hans-Carsten A1 - Nemecek, J. A1 - Fontana, Patrick ED - E. Fehling, ED - Schmidt, M. ED - S. Stürwald, T1 - Micro texture and mechanical properties of heat treated and autoclaved Ultra High Performance Concrete (UHPC) KW - Ultra high performance concrete KW - Micro texture KW - Mechanical strength KW - Secondary cemetitious materials PY - 2008 SN - 978-3-89958-376-2 IS - 10 SP - 213 EP - 220 CY - Kassel AN - OPUS4-16726 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Noll, Matthias A1 - Ferrero, Fabio A1 - Malow, Marcus T1 - Succession of the fungal and bacterial community structure in spruce wood debris T2 - Jahrestagung der Vereinigung für Allgemeine und Angewandte Mikrobiologie CY - Frankfurt am Main, Germany DA - 2008-03-09 PY - 2008 AN - OPUS4-16727 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Noll, Matthias A1 - Duc, L. A1 - Bürgmann, H. A1 - Zeyer, J. T1 - High diazotrophic diversity in the forefield of a receding alpine glacier T2 - Jahrestagung der Vereinigung für Allgemeine und Angewandte Mikrobiologie CY - Frankfurt am Main, Germany DA - 2008-03-09 PY - 2008 AN - OPUS4-16728 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias A1 - Stark, Wolfgang A1 - Goering, Harald T1 - Können UF-Formmassen überhärten? Die Aussage des Kochversuchs! T2 - 1. Wildauer Duromer-Tagung CY - Wildau, Germany DA - 2008-03-11 PY - 2008 AN - OPUS4-16730 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -