TY - JOUR A1 - Unger, Wolfgang A1 - Gross, Thomas A1 - Böse, Olaf A1 - Lippitz, Andreas A1 - Fritz, Thomas A1 - Gelius, U. T1 - VAMAS TWA2 Project A2: evaluation of static charge stabilization and determination methods in XPS on non-conducting samples. Report on an inter-laboratory comparison N2 - First results of an inter-laboratory comparison (27 participants in Europe, Japan and USA) of XPS data obtained with non-conducting samples are presented. Binding energies of Al 2s for alumina, N 1s and imide C 1s for Kapton and Sr 3p3/2 for a strontium titanate film on glass were obtained after static charge referencing with the help of 15 nm gold particles deposited at the surface of the test samples. For the alumina sample C 1s static charge referenced data are also presented. Repeat standard deviations (sr), between standard deviations (sb), reproducibility standard deviations (sR) and total means are evaluated from the experimental data. It can be stated that although the repeat standard deviation is as small as 0.05 eV in the best case, the standard deviation characterizing the reproducibility of the method is obviously not better than 0.15 eV in the best case at the present time. The knowledge of these standard deviations is important for metrology, validations of analytical procedures relying on qualitative photoelectron spectroscopy and XPS databanking. KW - XPS KW - ESCA KW - Binding energy KW - Inter-laboratory comparison PY - 2000 DO - https://doi.org/10.1002/1096-9918(200008)29:8<535::AID-SIA900>3.0.CO;2-5 SN - 0142-2421 SN - 1096-9918 VL - 29 SP - 535 EP - 543 PB - Wiley CY - Chichester AN - OPUS4-6939 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Friedrich, Jörg Florian A1 - Unger, Wolfgang A1 - Lippitz, Andreas A1 - Giebler, Rainer A1 - Koprinarov, Ivaylo A1 - Weidner, Steffen A1 - Kühn, Gerhard ED - Mittal, K. L. T1 - Significance of interfacial redox reactions and formation of metal-organic complexes for the adhesion of metals on pristine and plasma-treated polymers KW - Oxygen low-pressure plasma treatment of polymers KW - Metal-polymer interactions KW - Peel strength PY - 2000 SN - 90-6764-327-0 VL - 2 SP - 137 EP - 171 PB - VSP CY - Utrecht AN - OPUS4-6979 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Friedrich, Jörg Florian A1 - Ghode, Archana A1 - Kühn, Gerhard A1 - Weidner, Steffen A1 - Geng, Shiming A1 - Retzko, Iris A1 - Unger, Wolfgang A1 - Lippitz, Andreas ED - Schindel-Bidinelli, E. T1 - Polymeroberflächenfunktionalisierungen im gepulsten Plasma mit nachfolgender chemischer Behandlung T2 - 14. Internationales Symposium Swissbonding ; 14. Internationaler Kongreß Swiss Bonding ; 14th Swiss Bonding 00 CY - Rapperswil, Schweiz DA - 2000-05-16 PY - 2000 SP - 31 EP - 44 PB - SWIBOTECH GmbH CY - Bülach AN - OPUS4-6980 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tscharntke, Dirk A1 - Erhard, Anton A1 - Wüstenberg, Hermann T1 - Bewertung kritischer Befunde bei der Ultraschallprüfung an Schweißnähten mit Modellrechnungen T2 - 222. Sitzung der DGZfP e.V. Arbeitskreis Berlin CY - Berlin, Germany DA - 2000-09-05 PY - 2000 AN - OPUS4-4584 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Aurich, Dietmar A1 - Baer, Wolfram A1 - Häcker, Ralf A1 - Klingbeil, Dietmar A1 - Künecke, Georgia A1 - Ohm, Katrin ED - Richard, H. A. T1 - Untersuchungen zur Bewertung des Zähigkeitsverhaltens im Übergangsbereich vom Spaltbruch zum Gleitbruch N2 - Im Hinblick auf das Verhalten von Bauteilen aus ferritischen Stählen im Übergangsbereich vom Gleitbruch zum Spaltbruch wurden in einem vom BMBF geförderten Forschungsvorhaben, über das nachfolgend auszugsweise berichtet wird, u.a. folgende Ziele verfolgt: • Abgrenzung des Anwendungsbereichs der elastisch-plastischen Bruchmechanik zu tiefen Temperaturen hin, • Möglichkeiten und Grenzen der Nutzung von Zähigkeitspotentialen im Übergangsbereich, • Ermittlung des Einflusses des Spannungszustandes auf das Bruchverhalten im Übergangsbereich und • Übertragbarkeit auf Bauteile. T2 - 32. Tagung des DVM-Arbeitskreises Bruchvorgänge CY - Berlin, Germany DA - 22.02.2000 PY - 2000 SN - 0943-3473 SP - 109 EP - 119 PB - DVM CY - Berlin AN - OPUS4-7025 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Just, Ulrich A1 - Jones, D.J. A1 - Krüger, Rita A1 - Davidson, G. A1 - Käppler, K. T1 - SFC/FTIR, SFC/APCI-MS and MALDI-TOF-MS for the analysis of siloxane-ethylene oxide copolymers N2 - Polydimethylsiloxanes (PDMSs) modified by introducing ethylene oxide units with the aim of forming sufficiently water-soluble siloxane compounds were characterized using supercritical fluid chromatography (SFC) coupled with Fourier transform infrared (FTIR) spectroscopy and atmospheric pressure chemical ionization mass spectrometry (APCI–MS), and matrix-assisted laser desorption–ionization time-of-flight mass spectrometry (MALDI–TOF-MS). SFC has a domain in analyzing oligomers. Hyphenated techniques enable elucidation of the components. Remarkable is the resolution and short analysis time of MALDI–TOF-MS. SFC also allows quantification of the basic and reaction products. PY - 2000 DO - https://doi.org/10.1016/S0165-022X(00)00077-4 SN - 0165-022x IS - 43 SP - 209 EP - 221 PB - Elsevier CY - Amsterdam AN - OPUS4-11336 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böllinghaus, Thomas ED - Richard, H. A. T1 - Sicherheit von Schweißverbindungen gegen wasserstoffunterstützte Rissbildung T2 - 32. Tagung des DVM-Arbeitskreises Bruchvorgänge CY - Berlin, Deutschland DA - 2000-02-22 PY - 2000 SN - 0943-3473 SP - 173 EP - 182 PB - DVM CY - Berlin AN - OPUS4-11843 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böllinghaus, Thomas A1 - Hoffmeister, H. T1 - Hydrogen permeation in supermartensitic stainless steels dependent on heat treatment and chemical composition N2 - Hydrogen might cause severe degradation of supermartensitic stainless steels, if they are activated during exposure to sour environments. Consistent and comprehensive data for hydrogen transport in these materials are thus required to support, in particular, modelling of hydrogen assisted cracking as a part of life time assessment of welded steel components. In addition to previously published diffusion coefficients and subsurface concentrations of a supermartensitic stainless steel further data dependent on heat treatment are provided by this contribution. Furthermore, a higher alloyed material has been investigated in the state as received and also in the quenched condition, in order to approach the influences of chemical composition on hydrogen transport in supermartensitic stainless steels. With respect to welding it turned out that the diffusion coefficient and the subsurface concentration are markedly dependent on heat treatment of the materials. T2 - Corrosion 2000 CY - Orlando, FL, USA DA - 2000-03-26 PY - 2000 SP - Paper 00141, 1 EP - 19 PB - NACE International CY - Houston, Tex. AN - OPUS4-11844 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Böllinghaus, Thomas A1 - Hoffmeister, H. T1 - A numerical model for hydrogen assisted cracking PY - 2000 DO - https://doi.org/10.5006/1.3280564 SN - 0010-9312 SN - 1938-159X VL - 56 IS - 6 SP - 611 EP - 622 PB - National Association of Corrosion Engineers CY - Houston, Tex. AN - OPUS4-11845 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kannengießer, Thomas A1 - Florian, Wolfgang A1 - Böllinghaus, Thomas A1 - Herold, H. ED - Miannay, D. P. T1 - Analysis of welding reaction stresses and welding reaction moments in component tests - Stress characteristics dependent on the intensity of restraint N2 - Up to the present, the thermomechanical loads during welding and subsequent cooling under design-specific shrinkage restraint resulting from the interaction between the materials and the structure have often not been taken into consideration approperiately for weldability assessment of components. As compared to previous investigations using small specimens this report presents component weld tests under varying intensities of restraint. Online records of the reaction forces and moments demonstrate in which way the intensity of restraint affects the reaction stresses and moments and their meaning for the evaluation of the load level in welded components. T2 - EUROMAT Topical 2000 CY - Tours, France DA - 07.11.2000 PY - 2000 SN - 0-08-042815-0 VL - 1 SP - 145 EP - 150 PB - Elsevier CY - Amsterdam AN - OPUS4-11847 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Schobbert, Helmut A1 - Böllinghaus, Thomas A1 - Schöler, Annett T1 - Heißrißsicherheit hochlegierter austenitischer Stähle beim Laser- und Hybridschweißen N2 - Eine Reihe nichtrostender austenitischer Cr-Ni-Stähle in der Nähe der eutektischen Rinne können beim Laserschweißen sowohl primär ferritisch als auch primär austenitisch erstarren. Speziell konzipierte Heißrißprüfungen zeigen eine Rißanfälligkeit der im Unterschied zum WIG-Schweißen mit großen Streckenenergien beim Laserschweißen mit kleinen Streckenenergien primär austenitisch erstarrenden Gefügebereiche. Die Ursache dafür ist, daß im Unterschied zu einer langsamen primär ferritischen Erstarrung bei einer schnellen Erstarrung über metastabile primär austenitische Zustände Restschmelzen entstehen können, die gegenüber dem Grundwerkstoff erhebliche temperaturabhängige Zähigkeitsverluste aufweisen. Es wird gezeigt, wie sich durch die Wahl auf den Werkstoff gezielt abgestimmter Schweißparameter die Heißrißsicherheit beim Laserschweißen weitestgehend sicherstellen läßt. Darüber hinaus werden Perspektiven vorgestellt, wie die Heißrißsicherheit bei Hybridschweißen durch die Auswahl vom Zusatzwerkstoffen und durch eine geeignete Prozeßführung zu erreichen ist. T2 - 12. Jahrestagung Schadensanalyse CY - Würzburg, Germany DA - 18.10.2000 PY - 2000 SN - 3-18-091556-0 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte IS - 1556 SP - 225 EP - 240 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-11849 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Böllinghaus, Thomas ED - Cerjak, H. T1 - Modelling of Hydrogen Diffusion and Cracking in Steel Welds N2 - Hydrogen assisted steel corrosion and cold cracking is still a major topic regarding the reliability of welded steel components, such as offshore platforms and pipelines. Measurement of local and crack critical hydrogen concentrations in a specific weld is difficult and not very precise. Numerical simulations of hydrogen uptake and diffusion developed within the last twenty years have to be regarded as much more effective to determine local hydrogen concentrations in crack critical regions of welds. As an overview of existing theories of the state of the art in modelling of hydrogen cracking in steels, the present contribution shows that the development of a comprehensive numerical model for both types of hydrogen assisted cracking in welds, hydrogen assisted stress corrosion cracking and cold cracking, is still a major research task. As a first step towards that direction, a basic procedure for numerical simulation of crack initiation and propagation has been developed and experimentally verified. The approach can be extended to a comprehensive quantitative model for life time prediction and risk based inspection of welded steel components. (Steel specimen used was S355 along with other materials such as AISI 321, Incoloy 800, Inconel 690 and 600.) T2 - Fifth International Seminar on the 'Numerical Analysis of Weldability' CY - Graz, Austria DA - 1999-09-01 PY - 2000 SN - 1-86125-115-7 N1 - Serientitel: Book / The Institute of Materials – Series title: Book / The Institute of Materials IS - 738 SP - 1019 EP - 1059 PB - IOM Communications CY - London AN - OPUS4-11841 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Kannengießer, Thomas A1 - Böllinghaus, Thomas A1 - Florian, Wolfgang A1 - Herold, H. T1 - Effect of weld metal strength and welding conditions on reaction forces and stress distribution of restrained components N2 - Düring the past decades, weldability studies have predominantly been concentrated on the material and the welding process. In order to achieve a closer insight into the structural effects, component weldability tests have been performed by online monitoring of the reaction forces and moments. As a particular item, the effects of different strengths of the base and filier material on the reaction force and stress build up transverse to the welding direction have been studied at a specific structural restraint. As a most relevant result for practical welding it is demonstrated that the final reaction force and also the reaction stress level in the multilayer butt welds decreases with overmatch of the weld metal. PY - 2000 IS - IX-1971-00 SP - 1 EP - 18 PB - International Institute of Welding CY - Paris AN - OPUS4-11842 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Plarre, Rüdiger A1 - Hertel, Horst T1 - Wirtssuche beim Hausbockkäfer Hylotrupes bajulus (L.) (Coleoptera: Cerambycidae) KW - Hylotrupes bajulus KW - Host selection behavior KW - Mating behavior KW - Wood protection KW - Wood boring insects PY - 2000 SN - 0344-9084 VL - 12 SP - 493 EP - 498 PB - Deutsche Gesellschaft für Allgemeine und Angewandte Entomologie CY - Gießen AN - OPUS4-11821 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hertel, Horst A1 - Plarre, Rüdiger T1 - Incorporating insect behaviour in standard tests of wood preservatives - a possible way to reduce pesticide loadings T2 - 31th Annual Meeting of the International Research Group on Wood Preservation CY - Kona, HI, USA DA - 2000-05-14 KW - Standard test methods KW - Behavior KW - Wood preservatives KW - Hylotrupes bajulus PY - 2000 SP - Paper 20190, 1 EP - 10 PB - International Research Group on Wood Preservation CY - Stockholm AN - OPUS4-11822 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kolar, J. A1 - Strlic, M. A1 - Pentzien, Simone A1 - Kautek, Wolfgang T1 - Near-UV, visible and IR pulsed laser light interaction with cellulose PY - 2000 UR - http://www.sciencedirect.com/science?_ob=PublicationURL&_tockey=%23TOC%236640%231991%23999289998%23271349%23FLP%23&_cdi=6640&_pubType=J&_auth=y&_acct=C000049503&_version=1&_urlVersion=0&_userid=963821&md5=0020a82b8d5f591abc3354091a7def13 DO - https://doi.org/10.1007/s003390050031 SN - 0947-8396 VL - 71 IS - 1 SP - 87 EP - 90 PB - Springer CY - Berlin AN - OPUS4-5991 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Paatsch, Wolfgang A1 - Kautek, Wolfgang A1 - Krüger, Jörg T1 - Structuring and Plating of Materials with Ultrashort Laser Pulses PY - 2000 SN - 0016-4232 VL - 91 IS - 5 SP - 1271 EP - 1275 PB - Leuze CY - Saulgau, Württ. AN - OPUS4-6000 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kautek, Wolfgang A1 - Pentzien, Simone A1 - Röllig, Mathias A1 - Rudolph, Pascale A1 - Krüger, Jörg A1 - Maywald-Pitellos, C. A1 - Bansa, H. A1 - Grösswang, H. A1 - König, E. T1 - Near-UV laser interaction with contaminants and pigments on parchment: laser cleaning diagnostics by SE-microscopy, VIS-, and IR-spectroscopy PY - 2000 SN - 1296-2074 SN - 1778-3674 VL - 1 IS - sup.1 PB - Elsevier CY - Paris AN - OPUS4-5981 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kolar, J. A1 - Strlic, M. A1 - Müller-Hess, D. A1 - Gruber, A. A1 - Troschke, K. A1 - Pentzien, Simone A1 - Kautek, Wolfgang T1 - Near-UV and visible pulsed laser interaction with paper N2 - The applicability of excimer laser at 308 nm and Nd:YAG laser at 532 nm with fluences below 0.86 J/cm2 for cleaning of cellulose and paper materials was evaluated. The extent of degradation of purified cotton cellulose and Fabriano paper after laser treatment as well as after a period of accelerated humid oven ageing was determined by following the changes in the degree of polymerization. While irradiation of paper with the excimer laser at 308 nm results in depolymerization of cellulose accompanied by a decrease in ISO brightness, no detrimental effects of Nd:YAG laser treatments were observed. PY - 2000 DO - https://doi.org/10.1016/S1296-2074(00)00149-7 SN - 1296-2074 SN - 1778-3674 VL - 1 IS - sup.1 SP - 221 EP - 224 PB - Elsevier CY - Paris AN - OPUS4-5979 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian T1 - Bruchmechanische Analyse des Grenzflächenversagens bei Einzelfaser Pull-out und Fragmentation Tests T2 - DVM-Tagung Bruchvorgänge CY - Berlin, Germany DA - 2000-02-22 PY - 2000 AN - OPUS4-5945 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian A1 - Qiao, Linan T1 - Analysis of fiber, matrix and interface fracture in composites and fragmentation tests T2 - ECCM 9 Conference CY - Brighton, England DA - 2000-06-04 PY - 2000 AN - OPUS4-5946 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian A1 - Hampe, Andreas A1 - Rudolph, Hans-Volker A1 - Ivers, Heinz T1 - Detektion von Schädigungen in Faserverbundwerkstoffen mittels Röntgenrefraktion T2 - Tagung: Compositeforschung in der Mechanik CY - Paderborn, Germany DA - 2000-12-04 PY - 2000 AN - OPUS4-5947 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian A1 - Hampe, Andreas T1 - Fiber, matrix and interface fracture in composites T2 - Gordon Research Conference on Composites CY - Ventura, CA, USA DA - 2000-01-09 PY - 2000 AN - OPUS4-5948 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Kannengießer, Thomas T1 - Untersuchungen zur Entstehung schweißbedingter Spannungen und Verformungen bei variablen Einspannbedingungen im Bauteilschweißversuch N2 - In der Beurteilung der Schweißbarkeit für die Sicherheit und Zuverlässigkeit von Bauteilen fanden bisher die aus der Interaktion zwischen den Werkstoffen und der Konstruktion resultierenden thermomechanischen Belastungen während des Schweißens und der nachfolgenden Abkühlung unter konstruktiv bedingter Schrumpfbehinderung häufig nur wenig Beachtung. Gegenüber bisherigen Untersuchungen an Kleinproben wurden daher im Rahmen dieser Arbeit bauteilrelevante Schweißverbindungen unter realistischen Spannungsverteilungen geprüft. Diese Bauteilschweißversuche wurden in einer speziellen Großprüfanlage unter Variation der Schrumpfbehinderung, des Grund- und Zusatzwerkstoffes sowie der Streckenenergie durchgeführt. Dabei erweist sich das Konzept des Einspanngrades als geeignet, um die reale konstruktionsbedingte Schrumpfbehinderung auf die Versuchsanlage zu transferieren. Mittels online-Aufzeichnungen der Reaktionskräfte und -momente konnte gezeigt werden, wie sich diese Einzeleinflussgrößen jeweils auf die Höhe und den Verlauf der Reaktionskräfte und -momente auswirken und welche Bedeutung sie für die Einschätzung des Belastungsniveaus in Form von Spannungen und Dehnungen in Bauteilen besitzen. Unter anderem stellte sich heraus, dass unter relativ geringen Einspanngraden eine unkritische Eigenbelastung des Bauteiles vorliegt, jedoch bei hoher Steifigkeit die thermomechanische Beanspruchung bis zum Riss führen kann. In dieser Arbeit wurde erstmalig die Wirkung der Festigkeit von Zusatzwerkstoffen auf die Spanungs-Dehnungsverteilung unter definierter Schrumpfbehinderung am Bauteil untersucht. Es zeigte sich, dass unabhängig vom Grundwerkstoff ein hochfester Schweißzusatz zu geringeren Reaktionskräften führt als beim Schweißen mit einem Schweißzusatz mit vergleichsweise niedrigerer Festigkeit. Weiterhin wurde der Dehnungsverlauf beim und nach dem Schweißen unter definierter Schrumpfbehinderung mittels Dehnungsmessstreifen und einem Wegmesssystem bestimmt. Abhängig vom Schweißnahtabstand und dem Einspanngrad traten charakteristische Verformungsverläufe auf. Anhand dieser Ergebnisse konnte eine bisher ungebräuchliche jedoch notwendige Aufteilung der Schweißung in Nah- und Fernfeld erfolgen. Mit der inkrementellen Bohrlochmethode wurden die Eigenspannungen im Nahtbereich unter Einspannung, nach dem Entlasten und nach dem Wiederbelasten auf das Niveau der ursprünglich wirkenden Reaktionskräfte der Proben ermittelt und mit röntgenografischen Werten verglichen. Der Zusammenhang zwischen Einspanngrad und den Nahteigenspannungen lässt sich durch einen einfachen funktonalen Ansatz beschreiben. Den Untersuchungen wurde aufgrund der auf diesem Gebiet vorliegenden sehr unzusammenhängenden Literatur ein detaillierter Kenntnisstand vorangestellt. PY - 2000 SN - 3-8265-8008-7 SN - 1616-7376 IS - 2000,1 SP - 1 EP - 235 PB - Shaker CY - Aachen AN - OPUS4-27594 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Chudoba, T. A1 - Schwarzer, N. A1 - Richter, F. A1 - Beck, Uwe T1 - Determination of mechanical film properties of a bilayer system due to elastic indentation measurements with a spherical indenter N2 - A recently developed theoretical model represents the generalization of the indentation of a sphere into an infinite homogeneous halfspace to the problem of a Hertzian load acting on a halfspace covered with one or more films having different elastic properties. The model allows the analytical calculation of the complete elastic stress field and the deformations within the films and the substrate. Some results of the model shall be confirmed by nanoindentation experiments using an UMIS-2000 nanoindenter into Si3N4/SiO2 and SiO2/ Si3N4 double layers on BK7 glass and Si(100) single crystal. The materials used allow accurate measurements due to their homogeneous, amorphous structure as well as low surface and interface roughness. After the determination of the instrument compliance and the real, depth dependent indenter radius the measured load–depth data are compared with calculated results. It is shown that measurement results can be correctly interpreted by the model. The onset of plastic deformation is investigated for the same samples by multiple partial unloading experiments with a 4-µm radius diamond sphere. The critical load at which a first deviation from a wholly elastic response occurs is used for a stress calculation with the model. The mechanical behavior of the different film combinations is interpreted by means of the von Mises comparison stress. The measured results, together with the analytical modeling, allow an optimization of the thickness and modulus of the individual layers to get a maximum mechanical stability. KW - Mechanical properties KW - Depth sensing indendation KW - Young´s modulus KW - Spherical indenter PY - 2000 DO - https://doi.org/10.1016/S0040-6090(00)01365-1 SN - 0040-6090 VL - 377-378 SP - 366 EP - 372 PB - Elsevier CY - Amsterdam AN - OPUS4-25573 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ludwig, Jörg T1 - Adequate Equivalence Minimum Wall Thickness Formula T2 - Ad-hoc-Arbeitsgruppe der ECE/WP.15 CY - Berlin, Germany DA - 2000-01-11 PY - 2000 AN - OPUS4-14943 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ludwig, Jörg A1 - Pötzsch, Klaus-Michael T1 - Alternate Arrangements in Connection with Protection against Damage T2 - Ad-hoc-Arbeitsgruppe der ECE/WP.15 CY - Berlin, Germany DA - 2000-01-12 PY - 2000 AN - OPUS4-14944 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ludwig, Jörg T1 - Bulk-Transport gefährlicher Güter T2 - ETH Zürich CY - Zurich, Switzerland DA - 2000-03-24 PY - 2000 AN - OPUS4-14962 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ludwig, Jörg T1 - Safety Aspects of Oil and Gas Transport by Pipelines and Tankers (Railroad Tank Cars) T2 - Middle East Technical University CY - Ankara, Turkey DA - 2000-09-04 PY - 2000 AN - OPUS4-14963 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ludwig, Jörg T1 - Einheitliche Abdeckung äquivalenter Risiken bei Gefahrguttransporten in Tanks T2 - Gefahrgut-Technik-Tage Berlin 2000 - Innovative Tanktechnik CY - Berlin, Germany DA - 2000-11-09 PY - 2000 AN - OPUS4-14964 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ludwig, Jörg T1 - Fehlertoleranz und Human Factor - Fehlertolerante Technik zur Unterstützung menschlicher Zuverlässigkeit T2 - Gefahrgut-Technik-Tage Berlin 2000 - Innovative Tanktechnik CY - Berlin, Germany DA - 2000-11-09 PY - 2000 AN - OPUS4-14965 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kautek, Wolfgang A1 - Pentzien, Simone A1 - Rudolph, Pascale A1 - Krüger, Jörg A1 - Maywald-Pitellos, C. A1 - Bansa, H. A1 - Grösswang, H. A1 - König, W. ED - Fotakis, C. T1 - Near-Ultraviolet Pulsed Laser Interaction with Contaminants and Pigments on Parchment: Spectroscopic Diagnostics for Laser Cleaning Safety T2 - 5th International Conference on Optics within Life Sciences CY - H¯erakleion, Greece DA - 1998-01-01 PY - 2000 SN - 3-540-66648-6 N1 - Serientitel: Optics within life sciences – Series title: Optics within life sciences IS - 5 SP - 100 EP - 107 PB - Springer CY - Berlin AN - OPUS4-6189 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan A1 - Hoffmann, V. A1 - Steers, E. A1 - Wetzig, K. T1 - Investigations of Emission Processes in Argon Glow Discharges Containing Hydrogen T2 - 2000 Winter Conference on Plasma Spectrochemistry CY - Fort Lauderdale, FL, USA DA - 2000-01-10 PY - 2000 AN - OPUS4-6135 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scholze, F. A1 - Procop, Mathias T1 - Response function of energy dispersive semiconductor X-ray detectors - a physical model T2 - European Conference on Energy Dispersive X-Ray Spectrometry, EDXRS-2000 CY - Kraków, Poland DA - 2000-06-18 PY - 2000 AN - OPUS4-6141 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griepentrog, Michael A1 - Dück, Alexander A1 - Wirth, Thomas T1 - PVD-Reference Layers for quantitative Analysis of N and C in steel and coatings by using electron and optical emission spectroscopy T2 - PSE 2000 CY - Garmisch-Partenkirchen, Germany DA - 2000-09-17 PY - 2000 AN - OPUS4-6142 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beck, Uwe A1 - Wirth, Thomas A1 - Sahre, Mario A1 - Männ, Marion A1 - Gamer, Nadja A1 - Hoffmann, V. A1 - Hentschel, R. A1 - Brauneck, U. A1 - Mollenhauer, R. T1 - Reference Coatings for GD-OES Depth Profiling - Results of a VAMAS Project T2 - PSE 2000 CY - Garmisch-Partenkirchen, Germany DA - 2000-09-17 PY - 2000 AN - OPUS4-6143 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Procop, Mathias A1 - Scholze, F. T1 - Aufbau und Funktionsweise von energiedispersiven Röntgenspektrometern T2 - 32. Kolloquium EDO CY - Saarbrücken, Germany DA - 2000-09-18 PY - 2000 AN - OPUS4-6121 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wirth, Thomas T1 - Standard-Messverfahren, Referenzmaterialien für die GD-OES, Aktivitäten der BAM T2 - 7. Deutsches Anwendertreffen "Analytische GDS" CY - Dresden, Germany DA - 2000-10-17 PY - 2000 AN - OPUS4-6122 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver A1 - Plehn, W. A1 - Wilke, Olaf A1 - Brödner, Doris T1 - Eco-Label for low emission wood products and wood base products (RAL-UZ-38) - Part 1: Criteria and requirements for labelling T2 - Healthy Buildings 2000 CY - Espoo, Finland DA - 2000-08-06 PY - 2000 AN - OPUS4-7196 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Epishin, Alexander A1 - Link, T. A1 - Portella, Pedro Dolabella A1 - Brückner, Udo T1 - Evolution of the gamma/gamma'-microstructure during high-temperature creep of a nickel-base superalloy KW - Nickel alloys KW - Creep KW - Mesostructure KW - Scanning electron microscopy (SEM) KW - Image analysis PY - 2000 SN - 1359-6454 SN - 1873-2453 VL - 48 SP - 4169 EP - 4177 PB - Elsevier Science CY - Kidlington AN - OPUS4-7152 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maultzsch, Matthias ED - Zajc, A. T1 - Prüfung der Beständigkeit von Beton - Preskusanje obstojnosti betonov T2 - 7. Slowenisches Beton-Kolloquium CY - Ljubljana, Slovenia DA - 2000-05-18 PY - 2000 SP - 51 EP - 55 AN - OPUS4-7160 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maultzsch, Matthias T1 - Baustoffrecycling in Europa - Erfahrungen aus Forschung und Entwicklung PY - 2000 SN - 0934-9243 N1 - Serientitel: Veröffentlichungen des Zentrums für Abfallforschung der Technischen Universität Braunschweig – Series title: Veröffentlichungen des Zentrums für Abfallforschung der Technischen Universität Braunschweig IS - 15 SP - 137 EP - 150 CY - Braunschweig AN - OPUS4-7161 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bremser, Wolfram A1 - Schultze, Karin T1 - Certification of Traceable Environmental RM Using Cross-Verified Methods T2 - Int. Conference on Biological and Environmental Reference Materials BERM-8 CY - Bethesda, MD, USA DA - 2000-09-17 PY - 2000 AN - OPUS4-11454 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübner, Wolfgang A1 - Theiler, Geraldine A1 - Klein, P. A1 - Friedrich, K. T1 - Untersuchungen zum Einfluss kryogener Medien auf den Materialtransfer im Tribosystem Polymer-Komposit/Stahl T2 - Tribologie-Fachtagung 2000 CY - Göttingen, Deutschland DA - 2000-09-25 PY - 2000 SN - 3-00-003404-8 VL - 1 SP - 12-1 - 12-11 PB - Gesellschaft für Tribologie CY - Moers AN - OPUS4-12654 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klein, P. A1 - Friedrich, K. A1 - Theiler, Geraldine A1 - Hübner, Wolfgang T1 - Tribologische Untersuchungen an PTFE-Verbundwerkstoffen für den Einsatz in kryogenen Medien T2 - Tribologie-Fachtagung 2000 CY - Göttingen, Deutschland DA - 2000-09-25 PY - 2000 SN - 3-00-003404-8 VL - 1 SP - 9-1 - 9-10 PB - Gesellschaft für Tribologie CY - Moers AN - OPUS4-12655 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Peplinski, Burkhard A1 - Wenzel, Klaus-Jürgen A1 - Schultze, Dietrich T1 - Interlaboratory comparison (round robin) on the application of the Rietveld method to quantitative phase analysis by X-ray and neutron diffraction T2 - 7th European Powder Diffraction Conference (EPDIC-7) CY - Barcelona, Spain DA - 2000-05-20 PY - 2000 AN - OPUS4-12610 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Peplinski, Burkhard A1 - Wenzel, J. A1 - Schultze, Dietrich T1 - Certification of the phase composition of a BAM reference material by an interlaboratory comparison applying X-ray and neutron diffraction T2 - Symposium "Reference Materials for Technologies in the New Millenium" CY - Berlin, BAM, Germany DA - 2000-05-22 PY - 2000 SP - 1(?) EP - 13(?) AN - OPUS4-12600 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Peplinski, Burkhard A1 - Wenzel, Klaus-Jürgen A1 - Schultze, Dietrich T1 - Certification of the phase composition of a BAM reference material by an interlaboratory comparison applying X-ray and neutron diffraction T2 - EuraChem/EuroLab symposium "Reference materials for technologies in the new millenium" CY - Berlin, Germany DA - 2000-05-22 PY - 2000 AN - OPUS4-12615 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heinrich, Hans-Joachim A1 - Matschat, Ralf A1 - Czerwensky, Michael T1 - Determination of trace impurities in high purity iron materials T2 - 4th European Furnace Symposium and XV Slovak Spectroscopic Conference CY - Vysoké Tatry, Slovakia DA - 2000-06-12 PY - 2000 AN - OPUS4-15927 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulz-Forberg, Bernd A1 - Mair, Georg T1 - Auswirkung von Yellow Paper auf internationale Regelwerke und Normen T2 - 3. Gefahrgut-Technik-Tage Berlin "Innovative Tanktechnik" CY - Berlin, Deutschland DA - 2000-11-09 PY - 2000 IS - Projekt-Nr. 0206-III-0445 SP - 5 EP - 11 PB - Storck-Akademie CY - Hamburg AN - OPUS4-6038 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -