TY - THES A1 - Chun, Hyunjoo T1 - Experimentelle Untersuchungen und CFD-Simulationen von DTBP-Poolfeuern N2 - Es wurden Massenabbrandraten, Flammentemperaturen, spezifische Ausstrahlungen (Surface emissive power, SEP), Bestrahlungsstärken und Flammenlängen von DTBP- und Kerosin-Poolfeuern in Labor- und Feldversuchen (0.003 m < d < 3.15 m) gemessen und CFDSimulationen von DTBP- Poolfeuern bei d = 1.12 m und d = 3.15 m durchgeführt. Der Einfluss von Aktivierungs-, Verbrennungs- und Zersetzungsenergie sowie der Zersetzungsprodukte auf das Abbrandverhalten von DTBP wurde experimentell untersucht. Die mit der DDK gemessene Zersetzungsenergie von DTBP liegt im Bereich von – 189 kJ/mol bis – 210 kJ/mol, womit sie etwa 20 % bis 40 % höher ist als die mit dem DDK gemessene Aktivierungsenergie der Zersetzungsreaktion. Die in einem Verbrennungskalorimeter gemessene mittlere Verbrennungsenthalpie von DTBP beträgt = � c _H 36 000 kJ/kg. Die mit Hilfe der FTIR gefundenen Zersetzungsprodukte von DTBP in der Gasphase sind vor allem Aceton und Ethan. Die gemessenen Massenabbrandraten von DTBP-Poolfeuern (0.20 kg/(m² s) ≤ ′′ ≤ DTBP m& 0.30 kg/(m² s)) zeigen eine nur geringe Abhängigkeit vom Pooldurchmesser d, sind aber abhängig vom d fünf bis zwanzig mal größer als die von Kohlenwasserstoff-Poolfeuern. Die mit dem IR- Thermographie-System gemessenen Temperaturen der DTBP-Poolfeuer (1480 K bis 1580 K) sind im gesamten untersuchten Bereich ca. 300 K bis 600 K höher als die der Kerosin-Poolfeuer und stimmen mit den sehr heißen LNG-Poolfeuern bei 8 m ≤ d ≤ 15 m gut überein. Die mit dem IR-Thermographie-System über die gesamte Brenndauer gemessenen mittleren spezifischen Ausstrahlungen der DTBP-Poolfeuer betragen SEP = 130 kW/m² bei d = 1.12 m und SEP = 250 kW/m² bei d = 3.15 m und liegen somit um den Faktor drei bis zehn höher als bei Kohlenwasserstoff-Poolfeuern. Die mit (Ellipsoidal-) Radiometern gemessene mittlere Bestrahlungsstärke der DTBPPoolfeuer beträgt E (_y = 0.50 m, d =1.12 m) = 113 kW/m² und ist somit im Vergleich zu den n-Pentan-, Superbenzin- und Diesel-Poolfeuern um den Faktor zwei bis zehn größer. Die unter Verwendung der Thomas- Gleichung abgeschätzten Flammenlängen von DTBPPoolfeuern bei d < 0.50 m zeigen eine gute Übereinstimmung mit den mit S-VHSVideokameras gemessenen mittleren Flammenlängen (11d ≤ H ≤ 17d). Im Bereich von 0.05 m ≤ d ≤ 1.15 m sind die mittleren Flammenlängen H größer als im Experiment, sie stimmt dagegen bei d = 3.15 m gut überein und beträgt H (d = 3.15 m) ≈ 6d. Es wurden CFD-Simulationen von DTBP-Poolfeuern bei d = 1.12 m und d = 3.15 m unter Verwendung des kommerziellen ANSYS CFX Software Packet durchgeführt. Die dreidimensionalen Berechnungsgeometrien wurden mit Hexa-Gittern vernetzt, wobei die Anzahl der Zellen pro Volumen im Bereich von 100 000 bis 400 000 betrug. Die Zeitschritte für die CFD-Simulationen waren abhängig von der Feinheit des Gitters und dem Pooldurchmesser Δt = 10─ 2 s bis Δt = 10─ 5 s. Für die Modellierung der DTBP-Poolflammen wurde ein Datensatz für den Brennstoff DTBP im Preprocessor des ANSYS CFX-Programms implementiert. Es wurde die vollständige Verbrennung von DTBP berücksichtigt. Die Geschwindigkeitsgleichung der Irreversalreaktion ist etwa 1. Ordnung bezogen auf DTBP und Sauerstoff. Für die Temperaturabhängigkeit wurde der Arrhenius-Ansatz verwendet. Als Submodelle wurden das k-ε Turbulenzmodell, das Large Eddy Simulation Turbulenzmodell, das Detached Eddy Simulation Turbulenzmodell, das Scale Adaptive Simulation Turbulenzmodell, das Eddy Dissipation Verbrennungsmodell, das Rosseland Strahlungsmodell, das P1 Strahlungsmodell, das Monte Carlo Strahlungsmodell, das Discrete Transfer Strahlungsmodell und das Magnussen Rußmodell verwendet. Die simulierten maximalen Temperaturen der DTBP-Poolfeuer ergaben sich zu 1 410 K (d = 1.12 m) bzw. 1 520 K (d = 3.15 m), die gut mit den experimentell gemessenen Temperaturen übereinstimmen. Die simulierten mittleren spezifischen Ausstrahlungen für DTBP-Poolfeuer liegen bei SEP (d = 1.12 m) = 110 kW/m² und SEP (d = 3.15 m) = 180 kW/m². Die simulierten Flammenlängen der DTBP-Poolfeuer (5d ≤ H ≤ 6d) zeigen eine gute Übereinstimmung mit den gemessenen Flammenlängen. Die simulierten maximalen Strömungsgeschwindigkeiten in der Flammenmitte liegen z. B. für d = 3.15 m im Bereich von 25 m/s bis 30 m/s. Die simulierten Massenanteile an Ruß betragen 3.2∗ 10– 6 (d = 3.15 m) und 2.55∗ 10– 6 (d = 1.12 m). T3 - BAM Dissertationsreihe - 23 KW - Poolfeuer KW - Surface emissive power (SEP) KW - CFD-Simulation KW - Massenabbrandrate KW - Di-tert-butylperoxid PY - 2007 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1357 SN - 978-3-981655-0-0 SN - 1613-4249 VL - 23 SP - 1 EP - 157 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-135 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Bartholmai, Matthias T1 - Flammschutz von polymeren Baustoffen: Bewertung von Konzepten auf der Basis von Small-scale Cone Calorimeter Untersuchungen N2 - Flammschutz von polymeren Baustoffen: Bewertung von Konzepten auf der Basis von small- scale Cone Calorimeter Untersuchungen. In der Arbeit wurden zwei unterschiedliche Flammschutzkonzepte polymerer Baustoffe mit Hilfe des Cone Calorimeter untersucht und bewertet. Polymer-Schicht-Nanocomposites sind ein neues Konzept für flammgeschützte Werkstoffe, die aus einer Polymermatrix und der Zugabe eines nanoskaligen Schichtsilikat- Additivs von ca. 5 Gew.-% bestehen. Im Brandfall bilden die Schichtsilikate eine Barriere, die den Wärmetransport in das Material bzw. den Stofftransport der Pyrolysegase aus dem Material hemmt. Mit einem Modellsystem wurde gezeigt, dass dieser Barriereeffekt das Brandverhalten hinsichtlich der Flammenausbreitung verbessert, in anderen Brandszenarien aber wirkungslos bleibt. Die Ergebnisse der Cone Calorimeter Untersuchungen wurden mit denen der Entflammbarkeitstests UL 94 und LOI verglichen. Eine Korrelation in Richtung kleiner Probendimensionen (downscale) und in Richtung Phase der Brandentstehung wurde aufgezeigt. Die Anwendung intumeszierender Beschichtungen auf Bauteile verschiedener Art, wie z. B. tragende Stahlkonstruktionen, ist ein etabliertes Brandschutzkonzept. Das intumeszierende Polymermaterial schäumt unter Wärmeeinwirkung auf und bildet eine wärmeisolierende Schicht. Zur Bewertung der Wirkungsweise dieses Polymermaterials wurde ein auf Temperaturmessungen basierendes Verfahren mit dem Cone Calorimeter und für Simulationsrechnung entwickelt. Die Ergebnisse wurden mit denen aus Kleinprüfstanduntersuchungen verglichen. Eine Korrelation in Richtung großer Probendimensionen (upscale) und in Richtung der Phase des voll entwickelten Brandes konnte bis zu einer Temperaturgrenze gezeigt werden. N2 - Objective of this thesis was the investigation and evaluation of two different concepts of flame-retarding polymeric building materials. In the centre of this concern is the cone calorimeter as a versatile device in the field of flame retardancy and burning behaviour of materials and constructions. The cone calorimeter is characterized by a medium sample dimension (100 x 100 mm2). It simulates the phase of flame spread of a real burning process. The capabilities of the sample materials were of interest as well as the potentials and limitations of the investigation method. The scientific significance of cone calorimeter results was analysed in terms of different fire Scenarios and sample dimensions. Polymer Layered Silicate Nanocomposites are a new concept of flame retarding materials consisting of a polymer matrix and the addition of about 5 wt.-% nanoscale clay. In the case of a fire the clay layers built up a barrier, which hinders the heat transport into the sample and the mass transport of pyrolysis gases out of the material. Using a model system it was shown, that this barrier effect results in an essential improvement in burning behaviour in terms of flame spread but was ineffective for different fire scenarios and phases of burning, respectively. The results of cone calorimeter measurements were compared to results of the flammability tests UL 94 and LOI. A correlation towards smaller sample dimensions (downscale) and towards the phase of flammability was shown. The application of intumescent coatings on different structural members like supporting steel constructions is an established concept of fire retardancy. The intumescent polymeric material swells under thermal impact and forms a heat insulating layer. A method combining temperature measurement using the cone calorimeter and Computer simulation was developed, by which the fire protective effect could be evaluated. Investigation results were compared to results of small scale test furnace measurements. A correlation towards larger sample dimensions (upscale) and towards the phase of a fully developed fire could be shown up to a limitation by temperature. T3 - BAM Dissertationsreihe - 22 KW - Flammschutz KW - Small-scale Cone Calorimeter Untersuchungen KW - polymeren Baustoffen PY - 2007 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1366 SN - 978-3-86509-652-4 SN - 1613-4249 VL - 22 SP - 1 EP - 181 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-136 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Ritter, Martin T1 - A landmark-based method for the geometrical 3D calibration of scanning microscopes N2 - Die Arbeit stelle eine neue Strategie und ein daraus abgeleitetes Verfahren zur geometrischen Kalibrierung von 3D Messgeräten im Mikrobereich vor. Das Verfahren beruht auf der Anwendung von räumlichen Kalibrierstrukturen mit Nanomessmarken (Nanomarker). Es konnte erfolgreich für die 3D Kalibrierung von Rasterkraftmikroskopen (SPM) und konfokalen Lasermikroskopen (CLSM) eingesetzt werden. Im Rahmen von vergleichbaren Untersuchungen werden die 3D Kalibrierstrukturen ebenfalls für die photogrammetrische Selbstkalibrierung im Rasterelektronenmikroskop (SEM) verwendet. N2 - This thesis presents a new strategy and a spatial method for the geometric calibration of 3D measurement devices at the micro-range, based on spatial reference structures with nanometer-sized landmarks (nanomarkers). The new method was successfully applied for the 3D calibration of scanning probe microscopes (SPM) and confocal laser scanning microscopes (CLSM). Moreover, the spatial method was also used for the photogrammetric self-calibration of scanning electron microscopes (SEM). In order to implement the calibration strategy to all scanning microscopes used, the landmark-based principle of reference points often applied at land survey or at close-range applications has been transferred to the nano- and micro-range in the form of nanomarker. In order to function as a support to the nanomarkers, slopeshaped step pyramids have been developed and fabricated by focused ion beam (FIB) induced metal deposition. These FIB produced 3D microstructures have been sized to embrace most of the measurement volume of the scanning microscopes. Additionally, their special design allows the homogenous distribution of the nanomarkers. The nanomarkers were applied onto the support and the plateaus of the slope-step pyramids by FIB etching (milling) as landmarks with as little as several hundreds of nanometers in diameter. The nanomarkers are either of point-, or ring-shaped design. They are optimized so that they can be spatially measured by SPM and CLSM, and, imaged and photogrammetrically analyzed on the basis of SEM data. The centre of the each nanomarker serves as reference point in the measurement data or images. By applying image processing routines, the image (2D) or object (3D) coordinates of each nanomarker has been determined with subpixel accuracy. In contrast to the spatial reference structures applied for the spatial calibration method introduced here, present calibration methods for scanning microscopes use sequential measurements of 2D lattice and height step structures. This means that the determination of the scale factor for the height measurement yields an average value for the full scan area. Thus, the height scale factor remains independent of the lateral scanning position, and, therefore, it will be impossible to determine the coupling of the lateral coordinate axes and the z-axis as a shear factor with the sequential calibration method. On this account, an affine geometrical model has been used here, that allows for scale factors in all space directions, and, for coupling between all coordinate axes. With the help of the correlative analysis of the measurement data of all measurement methods applied (SPM, CLSM and photogrammetric SEM), for the first time, all scale factors, as well as the linear coupling of the probes used for the height measurement could be determined dependent on the lateral scanning position. It could be shown that the scanning movement of the SPM and the CLSM is erroneous. Due to hysteresis effects and guidance errors of the scanning generators, due to errors and peculiarities of the control cycle, and because of misaligned attachment of the probe with respect to the scanning plane, the measurement coordinate system is not identical to the ideal reference coordinate system. Scale and orthogonality of the measurement coordinate system have to be calibrated and corrected, in order to maintain the traceability to the SI-unit meter, and, therefore, to allow for quantitative dimensional 3D measurements. However, the correlative analysis of the SPM, CLSM and photogrammetric SEM measurement data after 3D calibration resulted in mean residues in the measured coordinates of as little as 13 nm. Without the coupling factors the mean residues are up to 6 times higher. By taking into account the orthogonality of the measurement coordinate axes when performing a 3D calibration, a comparative and quantitative analysis of 3D scanning microscopy has been made possible. T3 - BAM Dissertationsreihe - 21 KW - landmark-based method KW - scanning microscopes KW - geometrical 3D calibration PY - 2007 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1373 SN - 978-3-86509-630-2 SN - 1613-4249 VL - 21 SP - 1 EP - 141 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-137 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Bergmann, Meike T1 - Bestimmung polybromierter Diphenylether in Kunststoffen und Untersuchungen zum Emissionsverhalten N2 - Polybromierfe Diphenylether (PBDE) sind Flammschutzmittel, die in verschiedensten Produkten aus Kunststoff eingesetzt werden, um deren Entflammbarkeit herabzusetzen. Um den Eintrag in die Umwelt zu reduzieren, wurde die Anwendung von zwei PBDE-Kongeneren (penta- und octabromierte PBDE) im Rahmen der Richtlinie 2003/11/EG beschränkt. In der vorliegenden Arbeit wurde ein Verfahren zum Nachweis dieser PBDE in polymeren Produkten entwickelt. T3 - BAM Dissertationsreihe - 20 KW - polybromierter Diphenylether KW - Emissionsverhalten PY - 2007 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1382 SN - 978-3-86509-629-6 SN - 1613-4249 VL - 20 SP - 1 EP - 192 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-138 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Wolf, Martin T1 - Zur Phänomenologie der Heißrissbildung beim Schweißen und Entwicklung aussagekräftiger Prüfverfahren N2 - Zur Ermittlung der Heißrissresistenz beim Schweißen metallischer Werkstoffe können Heißrisstests eingesetzt werden. Obwohl bislang zahlreiche Heißrisstestverfahren entwickelt wurden, kann eine unerwartete Heißrissbildung während der Durchführung von Bauteilschweißungen oftmals nicht verhindert werden. Dies ist einerseits darauf zurückzuführen, dass sich die Bedingungen im Heißrisstest von den thermomechanischen Beanspruchungen einer Bauteilschweißung zu sehr unterscheiden. Andererseits erfolgt die Auswertung der meisten Heißrissversuche mit Hilfe empirischer Parameter, mit denen die eigentlichen Mechanismen der Heißrissentstehung jedoch nur unzureichend quantifiziert werden können. Ein wesentliches Ziel war es daher, aussagekräftige Methoden zur Quantifizierung des Heißrissverhaltens beim Schweißen zu entwickeln und damit einen Beitrag zur Erhöhung der Heißrisssicherheit geschweißter Bauteile zu leisten. N2 - For determining the hot cracking resistance of materials during welding of metallic materials it is possible to employ hot cracking tests. Despite numerous hot cracking tests have been developed till now, unexpected hot cracking during welding cannot always be avoided. This is on the one hand ascribed to the fact that the conditions prevalent in hot cracking testing differ too strongly from the thermomechanical loads imposed during component welding. On the other hand, evaluation of most hot cracking tests is carried out using empiric parameters which, however, fall short of adequate quantification of the actual hot cracking mechanism. A key aim of this study was therefore to develop convincing methods for quantifying the hot cracking behaviour during welding, and thus to make a contribution towards improving the hot cracking resistance of welded components. As a prerequisite, the Modified Varestraint Transvarestraint-Test (MVT-Test) was first upgraded with a view to varying the specimen loading rate over a very wide range up to quasi-instantaneous loading. As test material, Alloy 602 CA was chosen which exhibits a pronounced dependence of hot cracking resistance on the respective shielding gas. With the use of Ar 4.8 and Ar + 1% N2 as shielding gases, hot crack-critical as well as hot crack-uncritical material behaviour could be investigated. For further elucidation of the solidification cracking mechanism, a combined model was first developed which can be used to demonstrate that the solidification crack-critical limiting temperature TER and the solidification crack-critical strain rate (dε/dt)krit are largely independent of each other and must be determined using various test concepts. Numerical temperature calculations with first implementation of the reproduced real weld pool geometries helped to determine the solidification crack-critical limiting temperature for Alloy 602 CA as a function of different welding parameters and of the investigated shielding gases. It is demonstrated that the solidification crack-critical limiting temperature rises significantly with the use of Ar + 1% N2. In addition to this, the solidification crack-critical limiting temperature is significantly dependent on the applied welding parameters. The MVTTest was also used to conduct experiments with variable specimen loading rate in both the Varestraint and the Transvarestraint mode. Various hot cracking parameters determined in these experiments were evaluated quantitatively. With regard to exclusively qualitative determination of the hot cracking resistance of materials it was found that the measurable differences are more distinct in the Varestraint mode than in the Transvarestraint mode. For hot cracking test transferability investigations, the very critical specimen loading rates at which solidification cracking does not occur yet, were experimentally determined in MVTTests. Using the obtained results in conjunction with thermomechanical simulations, the local critical strain rates in the immediate vicinity of the weld pool were calculated. It is shown that the local critical strains and strain rates constitute a crack criterion for the transferability to the newly developed Controlled Tensile Weldability Test (CTW-Test). Keywords: Solidification cracking, liquation cracking, global strain, local strain, transferability, Modified Varestraint Transvarestraint Test, weld pool geometry, hot cracking parameter, Controlled Tensile Weldability Test, Alloy 602 CA. T3 - BAM Dissertationsreihe - 19 KW - Phänomenologie Heißrissbildung KW - Schweißen und Entwicklung aussagekräftiger Prüfverfahren PY - 2006 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1395 SN - 978-3-86509-599-2 SN - 1613-4249 VL - 19 SP - 1 EP - 218 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-139 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Alekseychuk, Oleksandr T1 - Detection of crack-like indications in digital radiography by global optimisation of a probabilistic estimation function N2 - A new algorithm for detection of longitudinal crack-like indications in radiographic images is developed in this work. Conventional local detection techniques give unsatisfactory results for this task due to the low signal to noise ratio (SNR ~ 1) of crack-like indications in radiographic images. The usage of global features of crack-like indications provides the necessary noise resistance, but this is connected with prohibitive computational complexities of detection and difficulties in a formal description of the indication shape. Conventionally, the excessive computational complexity of the solution is reduced by usage of heuristics. The heuristics to be used, are selected on a trial and error basis, are problem dependent and do not guarantee the optimal solution. Not following this way is a distinctive feature of the algorithm developed here. Instead, a global characteristic of crack-like indication (the estimation function) is used, whose maximum in the space of all possible positions, lengths and shapes can be found exactly, i.e. without any heuristics. The proposed estimation function is defined as a sum of a posteriori information gains about hypothesis of indication presence in each point along the whole hypothetical indication. The gain in the information about hypothesis of indication presence results from the analysis of the underlying image in the local area. Such an estimation function is theoretically justified and exhibits a desirable behaviour on changing signals. The developed algorithm is implemented in the C++ programming language and testet on synthetic as well as on real images. It delivers good results (high correct detection rate by given false alarm rate) which are comparable to the performance of trained human inspectors. N2 - In dieser Arbeit wurde ein neuer Algorithmus zur Detektion rissartiger Anzeigen in der digitalen Radiographie entwickelt. Klassische lokale Detektionsmethoden versagen wegen des geringen Signal-Rausch-Verhältnisses (von ca. 1) der Rissanzeigen in den Radiographien. Die notwendige Resistenz gegen Rauschen wird durch die Benutzung von globalen Merkmalen dieser Anzeigen erzielt. Das ist aber mit einem undurchführbaren Rechenaufwand sowie Problemen bei der formalen Beschreibung der Rissform verbunden. Üblicherweise wird ein übermäßiger Rechenaufwand bei der Lösung vergleichbarer Probleme durch Anwendung von Heuristisken reduziert. Dazu benutzte Heuristiken werden mit der Versuchs-und-Irrtums-Methode ermittelt, sind stark problemangepasst und können die optimale Lösung nicht garantieren. Das Besondere dieser Arbeit ist anderer Lösungsansatz, der jegliche Heuristik bei der Suche nach Rissanzeigen vermeidet. Ein globales wahrscheinlichkeitstheoretisches Merkmal, hier Schätzfunktion genannt, wird konstruiert, dessen Maximum unter allen möglichen Formen, Längen und Positionen der Rissanzeige exakt (d.h. ohne Einsatz jeglicher Heuristik) gefunden werden kann. Diese Schätzfunktion wird als die Summe des a posteriori Informationsgewinns bezüglich des Vorhandenseins eines Risses im jeden Punkt entlang der hypothetischen Rissanzeige definiert. Der Informationsgewinn entsteht durch die Überprüfung der Hypothese der Rissanwesenheit anhand der vorhandenen Bildinformation. Eine so definierte Schätzfunktion ist theoretisch gerechtfertigt und besitzt die gewünschten Eigenschaften bei wechselnder Anzeigenintensität. Der Algorithmus wurde in der Programmiersprache C++ implementiert. Seine Detektionseigenschaften wurden sowohl mit simulierten als auch mit realen Bildern untersucht. Der Algorithmus liefert gute Ergenbise (hohe Detektionsrate bei einer vorgegebenen Fehlalarmrate), die jeweils vergleichbar mit den Ergebnissen trainierter menschlicher Auswerter sind. T3 - BAM Dissertationsreihe - 18 KW - object detection KW - detection of elongated objects in low SNR condition KW - dynamic programming PY - 2006 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1400 SN - 978-3-86509-534-8 SN - 1613-4249 VL - 18 SP - 1 EP - 114 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-140 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Lüddecke, Falk T1 - Ein Beitrag zur Ertüchtigung bestehender Stahltragwerke unter besonderer Berücksichtigung des Fügeverfahrens Schweißen N2 - Bei einer Vielzahl im Betrieb befindlicher, vorwiegend ermüdungsbeanspruchter Stahltragwerke, um 1900 erbaut, ist die rechnerische Lebensdauer bereits überschritten. Die Bereitstellung möglicher Sanierungskonzepte zur Erhöhung der Tragsicherheit - damit zur weiteren Nutzung - dient für die Brückenbetreiber als wichtige Entscheidungsgrundlage bei der Wahl zwischen Ertüchtigungsmaßnahme und Neubau. Im Zuge von Ertüchtigungen muss oftmals bestehendes und beschädigtes Material durch Neumaterial ersetzt oder ergänzt werden. Der Erfolg der Ertüchtigungsmaßnahme hängt entscheidend von der kraftschlüssigen Verbindung zwischen Alt- und Neumaterial ab. In dieser Arbeit wird zur Steigerung der Effizienz von Ertüchtigungs- und Sanierungsmaßnahmen die Anwendbarkeit des Schweißens detaillierter untersucht. Da durch örtliche Ertüchtigungsmaßnahmen sowohl strukturelle Systemänderungen als auch lokal metallurgische Veränderungen hervorgerufen werden können, ist die Wahl eines geeigneten Schweißverfahrens und dessen Anpassung besonders wichtig. T3 - BAM Dissertationsreihe - 17 KW - Stahltragwerke KW - Fügeverfahren PY - 2006 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1410 SN - 978-3-86509-533-X SN - 1613-4249 VL - 17 SP - 1 EP - 181 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-141 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Hasenstab, Andreas Georg Maximilian T1 - Integritätsprüfung von Holz mit dem zerstörungsfreien Ultraschallechoverfahren N2 - Schadstellen im Inneren von Holzbauteilen (z. B. Innenfäule) oder baulich unzugängliche Oberflächenfäule stellen ein besonderes Problem dar, da diese von außen schlecht erkannt werden können und bei einer ausgeprägten Schädigung zu einem plötzlichen Versagen des Bauteils führen können. Ziel der vorliegenden Arbeit war es, eine Messapparatur zu entwickeln und damit zu untersuchen, ob und unter welchen Bedingungen Ultraschallechoverfahren an Holzbauteilen möglich sind. Weiter sollte untersucht werden, welche Schäden und Minderdicken mit Ultraschallecho von nur einer zugänglichen Seite aus geortet werden können. N2 - Wooden construction components bear serious problems, if they hold inner damage (e.g. interior rot) or damage of its surfaces at inaccessible locations. These failures are difficult to recognize from the outside, and might cause sudden malfunction of the structure. The aim of this work was to develop suitable measurement devices and to carry out investigations under which conditions ultrasonic echo technique can be successfully applied to wooden construction components. A further objective was to examine what kind of damage can be located with ultrasonic echo technique applied from only one accessible surface and if areas of reduced thickness can be determined. The investigations have shown that ultrasonic echo technique can be used at wooden constructions with longitudinal and transverse waves. For the first time, it was also possible to determine the different speeds of sound in wood for all polarizations and directions with low-frequency ultrasound. The coupling of the planar longitudinal wave probes (center frequency 100 kHz) required coupling media such as ultrasonic gel and Vaseline. This technique was better suited for smaller specimen with a thickness of less than 10 cm. No coupling media is necessary for the coupling of the transverse wave point contact probes (center frequency 55 kHz). With these probes also structures with larger dimensions could be examined. The use of transverse waves is better suited for several applications and many measurements have been carried out using the TD20 probes. The tests took place from one accessible side using pulse echo technique. Areas of reduced thickness can often be detected by receiving a direct echo, all other damage, e.g. rot, is indicated by shadowing the echo of the back wall. The sound velocity is calculated from the sound path and the transit time of the signal at an accessible part of the component. The echo impulse received from areas with reduced thickness or cavities can thus be related to a specific depth in the material. As the reason for the shadowing of the back wall echo is often not known, radiography with x-rays was used as a further non-destructive testing method and as second NDT method in special cases (reference method). A combination of digital radiography and mobile flash tube was also used and optimized for tests on wooden construction components and trees. The direct comparison between ultrasound technique and x-ray showed a trend towards similar detecting of defects. The ultrasound technique was more sensible for early damage detection. The combination of ultrasonic echo technique and radiography led to a very substantial reduction of possible misinterpretations of damage. Another example for the combination of methods was a fast investigation of large areas with ultrasonic echo technique, followed by an exact investigation at selected points with the minor destructive drilling resistance method. The research showed that ultrasonic echo applied from an accessible component side (only) permits the direct localisation of areas of reduced thickness, cavities, wooden pegs and large branches. Other damages such as rot or insect attack can be located indirectly by shadowing of the back wall echo. Thus a new testing method is available now for the non-destructive testing of wooden components. T3 - BAM Dissertationsreihe - 16 KW - Integritätsprüfung KW - Ultraschallechoverfahren KW - Holz PY - 2006 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1427 SN - 978-3-86509-527-5 SN - 1613-4249 VL - 16 SP - 1 EP - 190 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-142 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Chung, Jaeun T1 - Nanoscale Characterization of Epoxy Interphase on Copper Microstructures N2 - The epoxy/metal interface regions are recognized as crucial for the mechanical reliability of composite materials. In particular, the spatial stress distribution is governed by modulus variations, which may result from the physical-chemical interactions between epoxy and the metal surface. The properties of the interphase between bulk polymer and metal were analyzed in nanometer scale. It was aimed to characterize the stiffness gradient of the polymeric interphase, which was formed by a thermoset being cured in contact with a metal surface. N2 - Die Grenzfläche zwischen Epoxid und Metall spielt für die mechanische Zuverlässigkeit des Verbundwerkstoffes (Composite) Epoxid/Metall eine wichtige Rolle. Insbesondere hängt die räumliche Verteilung mechanischer Spannungen von Variationen des Elastizitätsmoduls ab, die durch die physikalisch-chemischen Wechselwirkungen zwischen dem Epoxid und der Metalloberfläche hervorgerufen werden können. Daher wurden die Eigenschaften des Grenzbereichs (Interphase) zwischen dem Polymer, das nicht durch Grenzflächen-Wechselwirkungen beeinflusst wurde (Bulk-Polymer), und dem Metall auf der Nanometer-Skala analysiert. Hauptziel war es, die Steifigkeitsgradienten innerhalb der Epoxid-Interphase zu detektieren. Diese können durch die Gegenwart der Metall-Grenzfläche (Interface) hervorgerufen werden, die einen Einfluss auf den Prozess der Aushärtung zeigt. Die Rasterkraftmikroskopie (Scanning Force Microscopy, SFM) im Force Modulation Mode (FMM) erlaubt die hochauflösende Abbildung von Steifigkeitsvariationen. Die Ergebnisse aus der SFM-FMM wurden mit Konzentrationsprofilen aus der energiedispersiven Analyse von Röntgenstrahlen im Rasterelektronenmikroskop (REM-EDX) verglichen, als auch mit Relaxationskurven aus der dynamisch-mechanischen Analyse (DMA), die an Epoxid-Referenzproben durchgeführt wurde. Die untersuchten Verbundwerkstoff-Proben bestanden aus Epoxid und Kupfer. Es wurde Elektronstrahl-Lithographie (EBL) in Verbindung mit der Lift-off Technik verwendet, um Kupfer-Mikroelektroden auf einem Silizium-Wafer herzustellen. Danach wurde die Mischung aus Epoxidharz und Amin-Härter in der Gegenwart der Kupfer-Mikroelektroden ausgehärtet, wodurch ein Epoxid/Kupfer Verbundwerkstoff entstand. Es wurden zwei verschiedene Epoxid-Härter Systeme verwendet, um unterschiedliche Probentypen herzustellen. Eines bestand aus Diglycidyl-Ether des Bisphenol A (DGEBA) und einem modifizierten cycloaliphatischen Amin (EPIKOTE828 und EPIKURE F205 von Resolution Europe). Das andere bestand aus DGEBA und einem aromatischen Amin (DER332 von Dow Chemical und DDS von Fluka Chemikalien). SFM-FMM erlaubt es, die lokalen mechanischen Eigenschaften des Grenzbereichs zu beschreiben. Die neue Art der Probenpräparation ermöglicht es, eine an die Erfordernisse der SFM-FMM angepasste Glattheit der zu untersuchenden Oberfläche zu erzielen. Bei der SFM-FMM wird die vertikale Position der Probe moduliert und die dynamische Verbiegungsamplitude des SFM-Cantilevers gemessen, während sich die Spitze im Kontakt mit der Probenoberfläche befindet. Neben dem resultierenden Amplituden- und Phasensignal sind noch andere Kontraste verfügbar, wie Topographie, Auflagekraft und Lateralkraft. Diese ergänzenden Kontraste wurden dazu verwendet, die Kupfer-Grenzfläche zu identifizieren. Ferner dienten sie der Kontrolle der Qualität der SFMMessung. Insbesondere konnte gezeigt werden, dass von der Topographie induzierte Kontraste auftreten können, wenn ihre Neigung mehr als ~|3°| beträgt. Außerdem wurde die Morphologie der Oberfläche des Epoxids untersucht, die noppenartige Strukturen, so genannte „Noduln“, aufwies. Bei den gegebenen Aushärtungsbedingungen (Tg bei 80°C über 2 Stunden, Nachhärtung bei 130°C über 1 Stunde) betrug die Durchschnittsgröße der Noduln ~125 nm, und 90 Prozent der Noduln waren zwischen 75 und 200 nm groß. Das aus EPIKOTE828-EPIKURE F205 bestehende Epoxid-System bildete eine Interphase mit einer Breite von ~1,9 μm aus und der Punkt der niedrigsten Steifigkeit war in einem Abstand von ~0,4 μm vom Kupfer. Andererseits wies das DER332-DDS System eine Interphase mit einer Breite von ~2,3–4,0 μm auf. Es wurden verschiedenartige Steifigkeitsprofile festgestellt. Diese Ergebnisse zeigen, dass die Eigenschaften des metallinduzierten Grenzbereichs vom Epoxid-System abhängen. Die Steifigkeit in der Nähe von Kupfer (bis zu 0,2–0,25 μm Abstand) war deutlich höher als im Volumen des Epoxids. Sowohl die im REM als auch die im TEM durchgeführten EDX-Messungen zeigten, dass die Konzentration des Amins in der Nähe von Kupfer verringert ist. Die unter Verwendung von SFM-FMM gemessene Steifigkeit wurde mit dem Modulwert verglichen, der mittels DMA an Referenzproben wohldefinierter Amin-Epoxid Konzentrationsverhältnisse bestimmt wurde. Die gefundene Relation wurde im Rahmen eines Reaktions-Diffusions Modells interpretiert. Danach treten räumliche Schwankungen im Konzentrationsverhältnis von Amin und Epoxid auf, die zu Variationen in der Netzwerkstruktur des ausgehärteten Epoxidsführen und sich somit auch auf dessen mechanische Eigenschaften auswirken. T3 - BAM Dissertationsreihe - 15 KW - Nanoscale Characterization KW - Epoxy Interphase KW - Copper Microstructures PY - 2006 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1435 SN - 978-3-86509-514-3 SN - 1613-4249 VL - 15 SP - 1 EP - 104 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-143 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Theiler, Géraldine T1 - PTFE- and PEEK-Matrix Composites for Tribological Applications at Cryogenic Temperatures and in Hydrogen N2 - Many new technologies are based on applications in extreme conditions, such as at low temperatures or in hydrogen environment. This involves new requirements on material properties, in particular regarding their operability and reliability. To fulfil this demand, the tribological behaviour of PTFE- and PEEK-matrix composites filled with carbon fibres were investigated at cryogenic temperatures and in hydrogen by means of surface analyses. For a better understanding of the tribological behaviour, and because of the temperature-dependent characteristics of polymer materials, thermal and mechanical properties of selected composites were initially investigated at low temperatures. Thermal shock experiments as well as cryo- and hydrogen treatments were carried out. Different coefficients of thermal expansion within the composite lead to debondings of particles, particularly in the case of PTFE materials. Tensile tests indicate that the YOUNG'S modulus increases at T= 77 K compared to room temperature. However, this improvement at low temperatures is moderate for PEEK composite which is already under its glass transition at room temperature. In the main investigation, tribological experiments were carried out at first at T= 77 K to observe the influence of the matrix, fillers and fibres on the material behaviour comparing to room temperature. The reduction of the friction coefficient and wear at low temperatures has been attributed to the low temperature properties of the polymer in particular due to the higher YOUNG'S modulus at T= 77 K. Whereas at room temperature friction and wear depend strongly of the CF content, the quantity of fillers and fibres does not have a significant effect on the tribological behaviour at low temperatures. At T= 77 K, the tribological behaviour of PTFE and PEEK composites is mainly influenced by the matrix. PEEK composites have a better tribological performance than PTFE materials especially regarding the wear resistance. Furthermore, the influence of the cryogenic medium was determined with experiments carried out in LN2 (T= 77 K), LH2 (T= 20 K) and LHe (T= 4.2 K), as well as in helium at T= 77 K and hydrogen at room temperature. The thermal properties of the cryogenic medium have a significant influence on the tribological performances of the composites. Due to the lower frictional heat at low sliding speed, the effect of low temperatures on the tribological behaviour of these composites was more clearly detected in this case, with a change in wear mechanism from mainly adhesive to more abrasive. Experiments in LN2 give the best friction and wear performance at low as well as at high sliding speed. The behaviour of these composites in LHe does not benefit from the low temperature properties of polymers due to the low heat of evaporation of LHe. The influence of hydrogen was particularly seen after the tribological experiments performed in LH2 on the surface of the disc. The reduction effect of hydrogen may have an influence on the tribochemical reactions which appear during sliding, enhancing the formation of iron fluorides, but no influence of the metal fluorides on the tribological performance could be determined in this study. N2 - Viele neue Technologien nutzen Anwendungen bei extremen Bedingungen, wie etwa bei tiefen Temperaturen oder in Wasserstoffumgebung. Dies stellt neue Forderungen an die Werkstoffe, insbesondere an ihre Funktionsfähigkeit und Zuverlässigkeit. Um dem gerecht zu werden, wurde das tribologische Verhalten von kohlefaserverstärkten PTFE- und PEEKVerbundwerkstoffen bei tiefen Temperaturen und in Wasserstoff mit Hilfe von Oberflächenanalysen untersucht. Für ein besseres Verständnis des tribologischen Verhaltens und wegen der temperaturabhängigen Eigenschaften der Polymere wurden zuerst thermische und mechanische Untersuchungen bei tiefen Temperaturen durchgeführt. Temperatur-Wechselbeanspruchungen sowie Kryo- und Wasserstoffbehandlungen wurden durchgeführt. Unterschiedliche Wärmeausdehnungskoeffizienten innerhalb der Materialien verursachen Trennungen von Partikeln besonders bei PTFE-Verbundwerkstoffen. Experimente zur Bestimmung der Zugfestigkeit zeigen an, dass der E-Modul bei T = 77 K im Vergleich zur Raumtemperatur zunimmt. Diese Verbesserung ist jedoch für PEEKMaterial nicht sehr ausgeprägt, da es sich bei Raumtemperatur bereits unter seinem Glasübergang befindet. In der Hauptuntersuchung wurden tribologische Experimente zuerst bei T = 77 K durchgeführt, um den Einfluss der Matrix, der Füllstoffe und der Fasern auf das Materialverhalten im Vergleich zur Raumtemperatur zu beobachten. Der Reibwert- und die Verschleißabnahme bei T = 77 K ist mit den Tieftemperatur-Eigenschaften der Polymer-Materialien zu erklären, insbesondere wegen des höheren E-Moduls bei T = 77 K. Während Reibung und Verschleiß bei Raumtemperatur stark von dem CF-Gehalt abhängig sind, hat die Menge der Füllstoffe und der Fasern wenigen Effekt auf das tribologische Verhalten bei tiefen Temperaturen. Bei 77 K ist das tribologische Verhalten von PTFE und PEEK hauptsächlich durch die Matrix bestimmt. PEEK-Komposite haben ein besseres tribologisches Verhalten als PTFE, insbesondere im Hinblick auf den Verschleißwiderstand. Außerdem wurde der Einfluss des Kältemittels mit tribologischen Experimenten untersucht, die in LN2 (T = 77 K), LH2 (T = 20 K) und LHe (T = 4,2 K), sowie in Helium bei T = 77 K und Wasserstoff bei Raumtemperatur durchgeführt wurden. Die thermischen Eigenschaften des Kältemittels haben einen bedeutenden Einfluss auf die tribologischen Eigenschaften. Wegen der niedrigeren Reibungswärme bei geringerer Gleitgeschwindigkeit wurde die Wirkung der Tieftemperaturen auf das tribologische Verhalten dieser Verbundwerkstoffe in diesem Fall besonders deutlich. Dabei ist der Wechsel des Verschleißmechanismus von vorwiegend adhäsiv zu vorwiegend abrasiv zu beobachten. Ergebnisse in LN2 zeigen die niedrigsten Reibungszahlen und Verschleißwerte, sowohl bei niedriger als auch bei hoher Gleitgeschwindigkeit. Das Verhalten dieser Verbundwerkstoffe in LHe profitiert aufgrund dessen geringer Verdampfungswärme nicht von den Tieftemperatur-Eigenschaften der Polymere. Der Einfluss des Wasserstoffs wurde besonders bei den Oberflächenanalysen der Scheibe nach den tribologischen Experimenten in LH2 beobachtet. Die reduzierende Eigenschaft des Wasserstoffs könnte einen Einfluss auf die tribochemischen Reaktionen und darüber hinaus eine fördernde Wirkung auf die Bildung der Metallfluoride haben. Ein Einfluss dieser Metallfluoride auf das tribologische Verhalten konnte in dieser Arbeit nicht beobachtet werden. T3 - BAM Dissertationsreihe - 14 KW - Oberflächenanalyse KW - Tiefe Temperaturen KW - Tribologie PY - 2005 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1444 SN - 978-3-86509-378-7 SN - 1613-4249 VL - 14 SP - 1 EP - 132 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-144 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Lohrer, Christian Andreas T1 - Einflussgrößen auf die Selbstentzündung von Schüttgütern und Stäuben - experimentelle Untersuchungen und numerische Simulationen N2 - Selbstentzündungen von brennbaren Materialien können sowohl bei Prozessen in der Verfahrenstechnik als auch beim Transport oder Lagerung von Schüttgütern auftreten. Verschiedene Parameter, wie die Materialeigenschaften, die Lagerungsbedingungen und die Geometrie der Schüttung, beeinflussen den Selbstentzündungsvorgang. Eine zuverlässige Beurteilung der Lagerungs- und Transportsicherheit von Schüttgütern und Stäuben ist mit den bisher erarbeiteten Methoden nicht möglich. In der vorliegenden Arbeit wurde insbesondere der Einfluss der Lagerungsbedingungen auf das Selbstentzündungsverhalten von brennbaren Materialien untersucht. Die Untersuchungen wurden für verschiedene Kohlen und Korkmehl durchgeführt. Folgende Ergebnisse wurden erzielt: 1. Zur besseren Bewertung des Zustandes Zündung und Nicht-Zündung bei Warmlagerungsvorgängen wurde eine verfeinerte Methode vorgeschlagen. Sie besteht aus der Kombination der visuellen Begutachtung einer Probe nach dem Versuch (Verfärbungen, Aschebildungen etc.), dem aufgetretenen Massenverlust und dem Temperatur-Zeitverlauf. 2. Es wurde nachgewiesen, dass eine Reduzierung des Sauerstoffvolumenanteils in der Schüttgutumgebung zu einer Erhöhung der Selbstentzündungstemperatur (SET) führt. 3. Sowohl durch eine Wasserzugabe ("Regen") als auch durch eine rasche Erhöhung der relativen Luftfeuchtigkeit konnte eine zuvor unterkritisch gelagerte Schüttung in einen überkritischen Zustand gebracht werden. Zurückzuführen ist dies auf den zusätzlichen Wärmetransport in das Schüttgut durch Kondensation von Wasserdampf und Adsorption von Wassermolekülen an porösen Partikeloberflächen. 4. Versuche belegten, dass gleichförmige Konvektionsströmungen ("Wind") in der Schüttgutumgebung die SET kaum beeinflussten aber zu einer deutlichen Reduzierung der Induktionszeit führten. Einseitige Anströmungen der Proben sorgten bei überkritischen Lagerungstemperaturen für eine Verschiebung des Zündortes zur windabgeneigten Seite. Diese Ergebnisse bestätigen, dass die Anlaufphase der Selbstentzündung von Schüttgütern kinetisch kontrolliert und somit nicht vom Sauerstofftransport abhängig ist. 5. Es wurde ein mathematisches Modell erarbeitet, mit dessen Hilfe die Vorgänge der Aufwärmung, des Feuchtigkeitstransportes (Verdampfung, Kondensation und Adsorption), der Selbstentzündung sowie die Brandausbreitung von brennbaren Schüttgütern und Stäuben zu berechnen sind. Dieses Modell ermöglicht realistische Schätzungen über die Sicherheit von gelagerten Schüttgütern mit guter Übertragbarkeit auf große, experimentellen Untersuchungen schwer zugänglichen, Schüttungen wie z.B. Kohlenhalden. T3 - BAM Dissertationsreihe - 13 KW - Brennstoffe KW - Explosivstoffe KW - Kraftstoffe PY - 2006 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1454 SN - 978-3-86509-377-9 SN - 1613-4249 VL - 13 SP - 1 EP - 161 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-145 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Dengel, Jörg T1 - Heterogene Explosionen in Gas/Flüssigkeitssystemen mit ruhender Oberfläche: charakteristische Eigenschaften des Explosionsverhaltens und Mechanismen N2 - In dieser Arbeit wurde erstmalig das Explosionsdiagramm des heterogenen Systems Diethylketon/Sauerstoff-Stickstoff in Abhängigkeit vom Gasvordruck und vom Stoffmengenanteil des Sauerstoffs erstellt. Nach den bei Raumtemperatur in einer Rohrstrecke erhaltenen Ergebnissen existieren fünf Bereiche unterschiedlichen Explosionsverhaltens: Pseudogasdeflagrationen, Pseudogasdetonationen, Oberflächendeflagrationen, Oberflächendetonation und ein schmaler Bereich in dem keine Zündung des Systems möglich war. Ein weiteres Ziel dieser Arbeit bestand darin, den Mechanismus von Oberflächenexplosionen zu untersuchen. Durch Explosionsuntersuchungen am heterogenen System Diethylketon/Sauerstoff- Stickstoff wurde dabei festgestellt, dass sich in dem Bereich, in dem Oberflächendeflagrationen entstehen, nach der Zündung eine Diffusionsflamme ausbildet, welche sich auf der Flüssigkeitsoberfläche durch das Rohr bewegt. Bei hohen Sauerstoffkonzentrationen findet eine deflagrative Verbrennung im gesamten Gasraum statt. Solche Oberflächendeflagrationen werden durch die Zerstäubung des Brennstoffes infolge von Stoßwellen mit geringer Intensität hervorgerufen. Bei niedrigen Sauerstoffkonzentrationen in der Gasphase folgt dem Diffusionsflammenstadium ein Abbrandstadium. Durch den Einsatz der laserinduzierten Fluoreszenz konnte die früher von Hofmann publizierte These, dass ein Stofftransport durch die Flammen hindurch stattfindet, für eindimensionale Oberflächenexplosionen widerlegt werden. Experimentelle Untersuchungen am heterogenen System Methanol/Sauerstoff haben gezeigt, dass Oberflächendetonationen ebenfalls durch eine Zerstäubung des Brennstoffs als Folge der Wechselwirkung einer intensiven Gasströmung beziehungsweise der Wechselwirkung von Stoßwellen geringer Intensität mit der Flüssigkeitsoberfläche verursacht werden. Die dadurch gebildeten Aerosole befinden sich nur in einem schmalen Bereich über der Flüssigkeitsoberfläche. Es wurde festgestellt, dass sich die Detonationsfront nur in diesem schmalen Bereich über der Flüssigkeit durch das Rohr bewegt. Berechnungen der Einwirkung einer horizontal über die Flüssigkeit laufenden Stoßwelle bestätigen dieses Modell. Oberflächendetonationen sind außerdem dadurch gekennzeichnet, dass periodische Sekundarexplosionen auftreten. Solche oszillierenden Explosionen entstehen, da die im System befindlichen Reaktanden Sauerstoff und Lösemittel nicht beim ersten Durchlauf der Detonationswelle vollständig umgesetzt werden. Die bei den Explosionsversuchen durchgeführten Druckmessungen haben darüber hinaus gezeigt, dass Detonationen im heterogenen System mit explosionsfähiger Gasphase (Pseudogasdetonationen) sicherheitstechnisch gefährlicher sind als Gasdetonationen. N2 - For the first time, the explosion diagram of a heterogeneous system (represented by diethylketone/oxygen-nitrogen) in dependence on the initial gas pressure and the molar fractions of oxygen and nitrogen was measured in a steel tube. Experiments in such heterogeneous systems showed at room temperature that five ranges of different explosion behaviour in a tube exist: pseudogas deflagrations, pseudogas detonations, surface deflagrations, surface detonations and a small range in which an ignition of the system was impossible. Another aim of this work was to investigate the mechanism of surface explosions. Surface deflagrations are characterised by the formation of a diffusion flame which moves along the liquid surface through the tube after ignition. Measurements performed in the system showed that a combustion occurred in the whole gas phase at a high molar fraction of the oxygen. This surface deflagration is the result of the dispersion of the fuel into aerosol particles induced by shock waves with low intensities. At low molar fractions of the oxygen in the gas phase, the diffusion flame stadium is followed by the a burnout phase. The former published thesis of a mass transfer through the flames during the diffusion flame and burnout phase was rebutted for one dimensional surface explosions (explosions in the heterogeneous systems combustible, organic liquid and gaseous oxidiser in a tube) by using laser-inducedfluorescence (LIF). Surface detonations are caused by dispersion of the liquid phase into aerosol particles as a result of the interaction of shock waves with low intensity and the liquid-surface. The aerosols are located in a small area above the liquid surface. The detonation front moves only in this small area above the liquid surface through the tube. This was shown by high-speed video recordings. Calculations of the impact of a horizontal shock wave moving atop the liquid surface confirm this model. Another property of surface detonations is the occurrence of secondary explosions. Such explosions develop when oxygen and solvent are not completely converted during the first run of the detonation wave. Moreover, it was shown that explosions in heterogeneous systems including an explosive atmosphere (pseudogas explosions) are more dangerous than gas explosions. T3 - BAM Dissertationsreihe - 12 KW - Heterogene Explosionen KW - Explosionsverhaltens und Mechanismen KW - charakteristische Eigenschaften KW - ruhender Oberfläche KW - Gas/Flüssigkeitssystemen PY - 2005 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1462 SN - 978-3-86509-361-2 SN - 1613-4249 VL - 12 SP - 1 EP - 143 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-146 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Mitropetros, Konstantinos T1 - Shock induced bubble explosions in liquid cyclohexane N2 - In dieser Arbeit wurde der Einfluss von Stoßwellen auf organische Flüssigkeiten mit und ohne Gasblasen untersucht. In einer neu aufgebauten Apparatur wurden Untersuchungen mit Hilfe der Hochgeschwindigkeitsfotografie und mit Druckmessungen durchgeführt. Die Apparatur bestand aus einem zylindrischen Autoklav mit einem Blasengenerator an seinem Boden. Zur Erzeugung einer Detonationswelle war oberhalb des Autoklavs eine Rohstrecke angeflanscht. Die folgenden Parameter wurden variiert: die Entfernung zwischen benachbarten Gasblasen, die Zusammensetzung der Gasmischung in den Blasen, der Anfangsdruck des Systems, die Anfangsgröße der Blasen und die organische Flüssigkeit. Zwei verschiedene Typen von Blasenexplosionen wurden beobachtet. Ihr Hauptunterschied ist die zeitliche Verzögerung der Zündung. Die Blasenexplosion des Typs I erfolgt während der ersten stoßinduzierten Blasenschwingung. Die Blasenexplosion vom Typ II findet mit einer viel längeren Zündverzögerung statt. Sie wurde nur unter bestimmten Bedingungen beobachtet. Ein Explosionsmechanismus wurde auf der Basis der Beobachtungen vorgeschlagen. Nach diesem Mechanismus können sogar Gasblasen, die anfangs eine nicht explosionsfähige, brennstoffreiche Gasmischung enthalten, durch teilweise Kondensation des Brennstoffs explosionsfähig werden. Weitere Untersuchungen beziehen sich auf Kavitationsphänomene innerhalb der Flüssigkeit und auf die Wechselwirkung zwischen der Flüssigkeitsoberfläche und einer Stoßwelle. Ferner wurden die Explosionsgrenzen von Cyclohexan in reinem Sauerstoff bei erhöhten Drücken und Temperaturen bestimmt. Die sicherheitstechnischen Aspekte der Versuchsergebnisse werden diskutiert. N2 - In this work the influence of shock waves on organic liquids with and without bubbles is investigated. The experiments were performed in a new experimental setup with the help of high speed photography and pressure measurements. The apparatus consisted of a cylindrical autoclave with a bubble generator at its bottom. For the creation of a detonation wave a tube was installed on the top of the autoclave. The following parameters were varied: The distance between neighboring bubbles, the composition of the gaseous mixture inside the bubbles, the initial pressure of the system, the initial bubble size, and the organic liquid (cyclohexane, 2-ethylhexanal, cumene, and methanol). Two different types of bubble explosion were observed. Their main difference is the length of their ignition delay. The bubble explosion type I takes place during the first oscillation after the shock wave impact. Further important results about this type of explosion refer to: - the explosion range in relation to the composition of the gas mixture within the bubble as well as to the initial bubble size. - the direct ignition of a bubble by a shock wave emitted by a nearby bubble explosion. Such a phenomenon is experimentally observed for the first time. - the shock induced ignition of gas bubbles containing an initially non explosive fuel-lean gas mixture. Optical recordings of jet penetration into the bubble prove that shock wave induced enrichment in vapor of the surrounding liquid is an important stage before the ignition. - the observation of bubble explosion type I in all the investigated liquids. - the mechanism of bubble explosion type I. The bubble explosion type II takes place with much longer ignition delay. It was observed under certain conditions only. An explosion mechanism is proposed on the basis of the experimental results. According to this mechanism, even non explosive fuel-rich gaseous bubbles can become explosive due to partial condensation of the fuel. A further group of results refer to cavitation phenomena inside the liquid and to shock induced phenomena on the surface. Additionally, the explosion limits of gaseous cyclohexane in pure oxygen at elevated pressures and temperatures were determined. The safety engineering aspects of the experimental results are discussed. T3 - BAM Dissertationsreihe - 11 KW - bubble explosions KW - liquid cyclohexane PY - 2005 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1478 SN - 978-3-86509-360-4 SN - 1613-4249 VL - 11 SP - 1 EP - 191 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-147 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Braun, Ulrike T1 - Wirkungsmechanismen von Rotem Phosphor als Flammschutzmittel in Thermoplasten N2 - Das Brandverhalten von Rotem Phosphor in HIPS, PBT und PA66 wurde untersucht. Es wurde gezeigt, wie die Wirksamkeit von Rotem Phosphor in HIPS and PBT durch Kombination mit anderen Flammschutzmitteln zu verbessern ist. N2 - Polymers are flammable due to their chemical nature. As a consequence they must be treated with flame-retardants before they can be used in fields with high flammability risks, such as transport, electronic devices and building construction. The use of red phosphorus as a fire retardant has been encouraged because it is an environmentally friendly alternative to halogenated compounds. The intention of this thesis was to evaluate the potential of red phosphorus as a flame retardant and to determine its fire-retardant mechanisms in different thermoplastics. The thermal decomposition and combustion behaviour of HIPS, PBT and PA66 containing red phosphorus was studied. It further investigated how the activity and efficiency of red phosphorus in HIPS and PBT was influenced by additional flame retardants such as melamine polyphosphate, melamine cyanurate and magnesium hydroxide. The decomposition process was characterized by means of different thermogravimetric methods (TG-FTIR, TG-MS), and the combustion behaviour by cone calorimeter measurements at various external heat fluxes. The flammability was investigated with LOI and the residue of combustion was analysed by means of XPS. Based on these results models for decomposition process were postulated. Red phosphorus can act both by promoting char formation in the condensed phase, and through radical trapping in the gas phase. Red phosphorus acts in the condensed phase in PA66, and in the gas phase in HIPS. In PBT both mechanisms were observed, depending on the pH value. When red phosphorus is combined with fuel-dilution additives such as melamine species in HIPS and PBT, both flame retardants act independently. The combustion behaviour of the combined material can be described by superposition of the distinct flame-retarded materials. In the presence of a barrier former, such as magnesium hydroxide in HIPS, the gas-phase mechanism of red phosphorus remains unaffected; however, a slight anti-synergism results. This is based on formation of a magnesium phosphate barrier, which influences the efficiency of phosphorus as a radical trap. The results showed that the activity of phosphorus as a flame retardant in thermoplastics depends on the water content of the polymer, the pH value and the presence of functional groups in the polymer. The efficiency of phosphorus as a flame retardant in the condensed and gas phases depends on combustion conditions. T3 - BAM Dissertationsreihe - 10 KW - Roter Phosphor KW - Flammschutzmittel KW - Thermoplasten PY - 2005 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1486 SN - 978-3-86509-303-5 SN - 1613-4249 VL - 10 SP - 1 EP - 164 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-148 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Appajaiah, Anilkumar T1 - Climatic Stability of Polymer Optical Fibers (POF) N2 - Three of the five POF samples are studied more in detail to realize the effects of individual parameters and for forecasting longterm optical stability by short-term exposure tests. T3 - BAM Dissertationsreihe - 9 KW - Climatic Stability of Polymer Optical Fibers (POF) PY - 2005 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1495 SN - 978-3-86509-302-7 SN - 1613-4249 VL - 9 SP - 1 EP - 176 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-149 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Samadurau, Uladzimir T1 - Entwicklung nichtlinearer tomographischer Rekonstruktionsverfahren für die Materialprüfung und Prozessüberwachung N2 - Die Studie beschäftigt sich mit der Entwicklung von Methoden und Algorithmen zur Rekonstruktion dynamischer Prozesse. Dabei werden neue Ansätze zur Lösung der Rekonstruktionsaufgabe vorgestellt. T3 - BAM Dissertationsreihe - 8 KW - Entwicklung nichtlinearer tomographischer Rekonstruktionsverfahren KW - Prozessüberwachung PY - 2005 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1500 SN - 978-3-86509-301-9 SN - 1613-4249 VL - 8 SP - 1 EP - 92 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-150 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Brink, Arne Nielsen T1 - Einsatz der Impuls-Thermografie zur quantitativen zerstörungsfreien Prüfung im Bauwesen N2 - Qualitative und quantitative Möglichkeiten der Impuls-Thermografie als zerstörungsfreies Prüfverfahren im Bauwesen werden dargelegt. Es wird aufgezeigt, inwiefern sich die Impuls- Thermografie zur Lösung des inversen Problems eignet. N2 - Non-destructive testing in civil engineering gains more and more importance. So far it had only be used selectively for damage investigations at reconstruction measures for example. But in the future it could play a decisive role in the field of quality assurance. A requirement for applying non-destructive testing methods is their suitability for daily use. Therefore enhancements of the techniques which are partly at the laboratory stage up to technically mature testing methods with an adequate standardisation is a clear defined aim for the research institutions in this field. A method capable for non-destructive testing is impulse thermography, as it is an established technique for material testing in other industry branches. In addition passive thermography in civil engineering is accepted tool for the thermal testing of stationary systems. The advantages of thermography are the possibility of investigating extensive constructions and components fast and broadly and its imaging application allowing the data analysis directly at the site. Within the scope of this work qualitative and quantitative possibilities of impulse thermography as a non-destructive testing method will be presented. It will be shown to what extent impulse thermography is suited for solving the inverse problems. For investigating the practicability experimental measurements were made in the laboratory at three different practical specimen. In detail, voids in concrete structures (Pk1), delaminations of plaster on concrete constructions (Pk2) and defects behind cleaving tiles taken in thick bed mortar on concrete walls (Pk3) were studied. Besides the experimental measurements numerical simulations were carried out. Therefore a program was written based on finite differences. The method and the boundary conditions and the simulation program are described in this work. With the help of the program an extensive variation of every influence parameter was undertaken for specimen Pk1. In particular the effects on the maximum temperature difference between a reference and a defect and on the time of its appearance were analysed. After the parameter variation numerical simulations were carried out for the three specimen along the lines of the experimental measurements and compared with them. While the measurements and simulations for specimen Pk1 are in agreement on the main lines, the results diverge substantial for the other two specimen. Feasible reasons for these differences are discussed in chapter 7. With regard to the quantitative possibilities of impulse thermography in the scope of this work two approaches were considered. On the one hand the simulation results for specimen Pk1 were analysed systematically and used for the determination of the void depths. On the other hand the experimental and the simulated temperature time curves were fitted with a theoretical model. The results prove the suitability of impulse thermography for non-destructive testing in civil engineering for the tasks chosen within the scope of this work. T3 - BAM Dissertationsreihe - 7 KW - Impuls-Thermografie KW - Bauwesen PY - 2005 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1510 SN - 978-3-86509-300-0 SN - 1613-4249 VL - 7 SP - 1 EP - 122 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-151 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Jankowski, Lukasz T1 - Modelling and simulation of light propagation in non-aged and aged step-index polymer optical fibres N2 - This thesis discusses theoretical and practical aspects of modelling of light propagation in non-aged and aged step-index polymer optical fibres (POFs). Special attention has been paid in describing optical characteristics of non-ideal fibres, scattering and attenuation, and in combining application-oriented and theoretical approaches. The precedence has been given to practical issues, but much effort has been also spent on the theoretical analysis of basic mechanisms governing light propagation in cylindrical waveguides. As a result a practically usable general POF model based on the raytracing approach has been developed and implemented. A systematic numerical optimisation of its parameters has been performed to obtain the best fit between simulated and measured optical characteristics of numerous non-aged and aged fibre samples. The model was verified by providing good agreement, especially for the non-aged fibres. The relations found between aging time and optimal values of model parameters contribute to a better understanding of the aging mechanisms of POFs. N2 - Kunststofflichtwellenleiter (POFs) stellen ein verhältnismäßig neues Medium zur optische Datenkommunikation über kurzen Strecken dar (bis zu einigen hundert Metern). Sie arbeiten im sichtbaren Wellenlängenbereich des elektromagnetischen Spektrums und werden auch für Beleuchtung und für Sensor-Anwendungen verwendet. Während ihrer Einsatzdauer unterliegen POFs unterschiedlichen Arten von Umweltbeanspruchungen, hauptsächlich durch hohe Temperatur, hohe Feuchtigkeit und mechanischen Belastungen. Zahlreiche experimentelle Forschungen beschäftigten sich mit der standardisierten Prüfung der Zuverlässigkeit von im Handel erhältlichen Fasern. Jedoch gab es bisher wenig Erfolg bei der Bemühung, zwei grundlegende optische Erscheinungen, Absorption und Streuung, die die Lichtausbreitung in Fasern stark beeinflussen, zu verstehen und praktisch zu modellieren: Diese beiden Effekte beschreiben nicht nur die Qualität neuer Fasern, sondern sie werden auch stark durch die Alterungsprozess beeinflusst. Der Hauptzweck dieser Doktorarbeit war es, ein praktisch verwendbares und theoretisch gut fundiertes Modell der Lichtausbreitung in nicht gealterten und gealterten POFs zu entwickeln und es durch optische Experimente zu verifizieren. Dabei wurden anwendungsorientierte Aspekte mit theoretischer POF-Modellierung kombiniert. Die Arbeit enthält die erste bekannte Anwendung der Wellenanalyse zur Untersuchung der winkelabhängigen Eigenschaften der Streuung. Die Resultate der numerischen Beispiele stimmen mit den experimentell beobachteten Ergebnissen überein. Der Gebrauch der Wellenoptik war erforderlich, weil die vereinfachende Anwendung der geometrischen Optik zu einer den experimentellen Ergebnissen widersprechenden Winkelabhängigkeit führt. Die Resultate der Wellenanalyse wurden außerdem dazu verwendet, ein generelles POF-Modell zu entwickeln, das auf dem Strahlverfolgungsverfahren basiert. Für die praktischen Experimente wurden mehrere POF-Proben unterschiedlicher Hersteller künstlich gealtert, indem sie bis 4500 Stunden bei 100 °C gelagert wurden (ohne Feuchtekontrolle). Die Parameter der jeweiligen Simulationen wurden mittels einer systematischen Optimierung an die gemessen optischen Eigenschaften der gealterten Proben angeglichen. Die erreichte Übereinstimmung ist besser als in bisher vorliegenden Untersuchungen und bestätigt die Verwendbarkeit des Modells. Die Resultate deuten an, dass der Übertragungsverlust der gealterten Fasern in den ersten Tagen und Wochen der Alterung am stärksten durch eine wesentliche physikalische Verschlechterung der Kern-Mantel-Grenzfläche verursacht wird. Chemische Effekte des Alterungsprozesses scheinen im Faserkernmaterial zuerst nach einigen Monaten aufzutreten. Als Nebeneffekt dieser Arbeit wurde ein Kalibrierung- und Qualitätseinschätzungsverfahren für CCD-Kameras entwickelt. T3 - BAM Dissertationsreihe - 6 KW - modelling light KW - propagation KW - optical fibres KW - waveguide KW - scattering PY - 2005 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1520 SN - 978-3-86509-272-1 SN - 1613-4249 VL - 6 SP - 1 EP - 137 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-152 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Seeger, Dirk M. T1 - Wasserstoffaufnahme und -diffusion in Schweißnahtgefügen hochfester Stähle N2 - Die im Rahmen dieser Arbeit vornehmlich untersuchten supermartensitischen Stähle werden im Offshore-Bereich als geschweißte Flowlines eingesetzt. Diese Stähle sollen nach dem Prinzip „Fitness for Purpose“ bisher verwendete höher legierte Werkstoffe ersetzen. Die neuen Stähle sind aufgrund ihrer Korrosionsbeständigkeit und Festigkeit sehr gut für das beabsichtigte Einsatzgebiet geeignet. Im Sour Service besteht jedoch die Gefahr der Wasserstoffaufnahme mit nachfolgender Rissbildung. Zur Beurteilung der Risssicherheit der Schweißverbindungen sowie des unbeeinflussten Werkstoffes im Anlieferungszustand werden Wasserstofftransportdaten benötigt. Diese werden im Rahmen dieser Arbeit mittels Permeationsexperimenten an Stahlmembranen unter realistischen Einsatzbedingungen quantifiziert, so dass die Ergebnisse in computergestützte Lebensdauerberechnungen Eingang finden können. Die Untersuchungen zeigten, dass der Diffusionskoeffizient des jeweiligen Werkstoffs bzw. Gefüges nicht von der chemischen Zusammensetzung der Prüflösung abhängt. Die Subsurface-Konzentration, das ist die in die Werkstoffe eintretende Wasserstoff- konzentration, hängt dagegen vom pH-Wert, von der Schwefelwasserstoffsättigung und von der Zusammensetzung der Prüflösung ab. Die Abhängigkeit der Subsurface-Konzentration von der chemischen Zusammensetzung der Prüflösung wird zudem entscheidend durch die Chloridionenkonzentration bestimmt. Darüber hinaus wurde festgestellt, dass die chemische Zusammensetzung supermartensitischer Stähle das Permeationsverhalten erheblich beeinflusst. Beim Vergleich des Permeationsverhaltens von wärmebehandelten Proben mit Proben realer Schweißnahtgefüge ergaben sich Differenzen in Höhe einer Größenordnung. Das bedeutet letztlich, dass das Permeationsverhalten von Wasserstoff in solchen Schweiß- verbindungen für jeden Fall, abhängig von der chemischen Zusammensetzung und Temperaturführung, separat zu untersuchen ist. Zusätzlich wurde die Wasserstoffdiffusion und -aufnahme in Schweißnahtgefügen höchstfester Feinkornbaustähle untersucht. Die Ergebnisse zeigten, dass diese Werkstoffe schon bei geringfügig abgesenkten pH-Werten, wie sie in Spalten oder Rissen aufgrund von Hydrolyse vorherrschen können, Wasserstoff aufnahmen. Die Subsurface-Konzentration war wiederum von der chemischen Zusammensetzung der Prüfelektrolytlösung abhängig. Generell waren die Diffusionskoeffizienten und die Subsurface-Konzentrationen stark vom Gefüge abhängig. Der Vergleich der Resultate der höchstfesten Feinkornbaustähle S 1100 und S 890 zeigte, dass die Wasserstoffpermeation bei diesen Werkstofftypen weniger große Unterschiede aufwies als bei den supermartensitischen Stählen. N2 - The mainly investigated supermartensitic stainless steels are experiencing first applications in the offshore technology as welded flowlines. These materials are intended to replace higher alloyed steels following the principle „Fitness for Purpose“. These new types of steels are very suitable for those applications, because of their corrosion resistance and of their strength. But specially for the use under sour service conditions there exists the risk of hydrogen uptake with subsequent cracking. To evaluate the cracking resistance of the welds as well as of the unaffected material in the as-delivered condition, it is necessary to determine hydrogen transport data. Within the scope of this research project, such data are quantified in permeation experiments carried out on steel membranes under realistic application conditions. This procedure allows it to use the results in computer-assisted lifetime calculations. It was found that the diffusion coefficients of the respective materials and structures do not depend on the chemical composition of the electrolytic solution. By contrast, the subsurface concentration, i. e. the hydrogen concentration infiltrating into materials, depends on the pH value, on the H2S-saturation and on the composition of the electrolytic solution. The concentration of chloride ions was found to be the strongest factor of influence for the dependence of the subsurface concentration on the chemical composition of the electrolytic solution. In addition, a major influence of the chemical composition of supermartensitic steels on the permeation behavior has been established. The comparison of the permeation behaviour between heat treated specimens and specimens with realistic weld microstructure revealed that especially the diffusion coefficients of the heat treated specimens increased by about ten times. This means that the hydrogen permeation behaviour in such joints must be determined separately in each individual case depending on chemical composition and on the heat control. Additionally, the hydrogen diffusion and uptake in welded microstructures of ultra-high strength fine-grained structural steels was examined. The respective results showed that hydrogen uptake took place by a slight decrease of the pH value. Such decrease could be caused by hydrolysis, e. g. in crevices. The subsurface concentration was also dependent on the chemical composition of the electrolyte. A generally strong dependency of the diffusion coefficient and the subsurface concentration on the microstructure was found. A comparison of the results of both investigated steels S 1100 and S 890 showed that the hydrogen permeation in these materials does not differ as much as in the supermartensitic stainless steels. T3 - BAM Dissertationsreihe - 5 KW - Wasserstoffaufnahme und -diffusion KW - Schweißnahtgefügen hochfester Stähle PY - 2005 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1535 SN - 978-3-86509-271-3 SN - 1613-4249 VL - 5 SP - 1 EP - 144 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-153 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Viyanit, Ekkarut T1 - Numerical Simulation of Hydrogen Assisted Cracking in Supermartensitic Stainless Steel Welds N2 - Replacement of expensive duplex stainless steel and conventional carbon steel by a new generation of supermartensitic stainless steel has been taken into account since the last decade corresponding to the "Fitness for Purpose" concept in order to meet the technical- economical challenge for transportation flowlines of unprocessed oil and gas products in offshore technology, in particular. Supermartensitic stainless steels can provide appropriate material properties such as: improved strength-to-weight ratio, enhanced useful corrosion resistance as well as application at relatively low cost. With decreased carbon content and increased molybdenum content compared to traditional martensitic stainless steel, hydrogen assisted stress corrosion cracking (HASCC) problems have been found during service caused by hydrogen being taken up during from sour service environments by cathodic protection. Hydrogen assisted cold cracking in supermartensitic stainless steel can also occur during fabrication welding with hydrogen picked up during welding, since this steel is relatively crack-susceptible by hydrogen. Therefore, effects of hydrogen assisted cracking (HAC), i.e. HASCC and HACC, on characteristic susceptibility of girth welds of supermartensitic stainless steel pipelines are studied in the present thesis by numerical modelling, which is developed using a available commercial finite element program. Firstly, numerical modelling for simulation of HASCC based on the NACE-TM 0177-96 approach is carried out for providing a basic understanding of the crack propagation behaviour. Secondly, a two dimensional finite element according to the gauge length cross-section of the orbitally welded pipeline is created for numerical modelling in order to calculate the time to failure of welded the component exposed to the NACE electrolyte solution with various H2S saturation. Externally applied loads of a series of constant strain rates and of the load history of full scale testing are also taken into account. Finally, numerical modelling is carried out under three specific aspects, i.e. thermal analysis, structural analysis, and hydrogen diffusion analysis, in order to simulate HACC in supermartensitic stainless steel pipelines welded orbitally by four layers of matching filler wires with an interpass temperature of 40°C. T3 - BAM Dissertationsreihe - 4 KW - numerical modelling KW - supermartensitic stainless steel KW - girth welds KW - pipeline KW - hydrogen assisted cracking (HAC) KW - hydrogen assisted stress corrosion cracking (HASCC), KW - hydrogen subsurface concentration KW - full scale test KW - post weld heat treatment (PWHT) KW - hydrogen diffusion coefficient PY - 2005 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1542 SN - 978-3-86509-270-5 SN - 1613-4249 VL - 4 SP - 1 EP - 228 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-154 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Hoffmann, Heike T1 - Untersuchungen zur Biozidauswirkung auf Bodenbakterien mit Hilfe von mikrobiologischen und molekularbiologischen Methoden N2 - Angemessene Methoden zur Überprüfung von Bakterienpopulationen im Boden sind für die toxikologische Bewertung von Chemikalien, Bioziden und schadstoffbelasteten Böden besonders wichtig, da sie Auskünfte über die biologische Wirksamkeit eines Stoffes auf Organismen geben. Das Ziel der vorliegenden Arbeit bestand einerseits darin, molekularbiologische Methoden (Fluoreszenz in situ Hybridisierung) zur Analyse mikrobieller Populationen für den Lebensraum Boden zu etablieren. Anderseits sollte die Charakterisierung und funktionelle Beschreibung der mikrobiellen Bodenpopulation unter Biozideinfluss in zwei unterschiedlichen Modellsystemen (in Flüssigkulturen und Bodensystem) erfolgen. Seit einiger Zeit erfolgt eine Wandlung in der Holzschutzmittel-anwendung von metallhaltigen zu organisch basierten Wirkstoffen. Der Austrag und die Auswirkung von zwei organischen Holzschutzmittel-komponenten (Tebuconazol und Benzalkoniumchlorid) aus dem Holz in den Boden wurde zunächst mit Hilfe von Kultivierungstechniken und chemischen Analysen untersucht. Durch Bestimmung der koloniebildenden Einheiten (KBE) konnte eine Abschätzung über die Auswirkung der Biozide auf die Bodenbakterien gemacht werden. Die methodischen Einschränkungen und die Arbeitsintensität machte die Notwendigkeit für molekularbiologischer Methoden deutlich. Als zentrale molekularbiologische Methode wurde die Fluoreszenz in situ Hybridisierung (FISH) angewendet. Das Potential dieser Methode wurde zum einen an einem Modellsystem in Flüssigkulturen ("in vitro") getestet und zum anderen durch Etablierung einer Extraktionsmethode als Vorschritt der FISH- Technik für Bodensysteme anwendbar gemacht. Um zu verifizieren, inwieweit Biozide (besonders Tebuconazol und Benzalkoniumchlorid) auf unterschiedliche Bakteriengruppen wirken, wurde ein Modellsystem "in vitro" entwickelt. Anhand von ausgewählten Bakterienarten konnte gezeigt werden, dass mit Hilfe von FISH und einer "Färbe"- Methode (Live/Dead-Test) die Wirksamkeit der Biozide abgeschätzt werden kann. Es zeigte sich zum Beispiel, dass die Gram-Bakterien i.d.R. empfindlicher gegenüber Benzalkoniumchlorid waren als Gram-Bakterien. Die Untersuchungen an ausgewählten Reinkulturen und Mischkulturen erlaubten eine quantitative Abschätzung der Biozidauswirkungen und bieten ein Potential, Biozide vor ihrer Anwendung zu testen. Im Boden stören bzw. verhindern die Huminstoffe die Anwendung von FISH. Durch Etablierung einer Extraktionsmethode, bei der mit Hilfe von Polyvinylpyrrolidon (PVP) die Bakterienextrakte aufgereinigt werden, gelang es, die FISH-Technik auch für Bodensysteme anzuwenden. Es wurde ein zweites Modellsystem untersucht, bei dem die Populationänderung im Boden direkt durch FISH überprüft und gleichzeitig die Auswirkung der Biozide auf die Bodenfunktion anhand der Messung der Bodenatmung bestimmt wurde. Mit diesen Untersuchungen konnte gezeigt werden, dass bestimmte Bakteriengruppen bei toxischer Auswirkung von Tebuconazol und Benzalkoniumchlorid auf die Bodenatmung entweder prozentual im Boden zurückgingen (Gram-Bakterien mit niedrigen G+C- Gehalt durch Tebuconazolkontamination), oder andere Gruppen, einen gesteigerten Anteil in der Population zeigten (Proteobakterien der Subklasse Alpha und Gamma durch Benzalkoniumchlorid). Es war so möglich, durch FISH die Verteilung verschiedener phylogenetischer Gruppen mittels Einsatz spezifischer Oligonukleotidsonden im Boden zu untersuchen. Diese Untersuchungen sind geeignet, Bakterienarten mit möglichen hohen Abbaupotentialen zu finden. Anhand von verschiedenen Fallbeispielen von Verunreinigungen in Böden und Flüssigkulturen wurden die Möglichkeiten des Einsatzes von molekularbiologischen Methoden (besonders FISH) aufgezeigt. N2 - Suitable analysis techniques to detect bacterial communities are essential to assess the toxicity of chemical, biocides and polluted soil, because they can provide direct information about the biological efficacy of a specific compound on the organisms. The goal of the present thesis was firstly, to develop molecularbiological methods to investigate microbial population in soil ecosystems, and secondly to apply these methods for the characterization of microbial communities under biocide pollution. In recent times metal-based substances normally employed in wood preservation are being more commonly replaced by substances with an organic basis. The effluence and effect of two wood preserver compounds (tebuconazole, benzalconiumchloride) discharged from the wood into the soil was investigated using culture depending techniques and chemical analysis. By determination of colony forming units (cfu) one can estimate the effects of biocides on the soil bacteria. Due to methodical limitations and the level of work involved for such analysis, the necessity to develop molecular biological methods is evident. The fluorescence in situ hybridisation (FISH) was used as the basis for molecular biological investigations. On the one hand it was possible to test the potential of this method in a modellsystem („in vitro“), and on the other to apply it on soilsystems after establishing an extraction method as a first step before the FISH-technique. To verify how biocides (especially tebuconazole and benzalconiumchloride) effect different bacteria groups, the mode of action was tested in the model „in vitro“ system. By employing the FISH-technique and a „staining“- method (Live/Dead- test, moleculare probes, NL), the efficacy of the biocides could be estimated. It was shown that gram positive bacteria were more sensitive against benzalconiumchloride than gram negative bacteria. Investigations on these type of modellsystems with pure and mix cultures enable a quantitative evaluation of the biocides effectiveness, and provide a possibility for checking new biocides before application. In soil humic acid inhibit the application of FISH. An extraction method was established which functions by cleaning the bacterial extract with polyvinylpyrrolidone (PVP) and so it was possible to detect bacteria in soil with the FISH-technique. In a second modellsystem the changes of the population in the soil were investigated directly by FISH, while the soil function was controlled separately by measuring the soil respiration. In this examination it was shown, that under toxic influence to the soil respiration some bacteria groups decreased (gram positive bacteria with low G+C- Content under tebuconazole influence) in the soil, whereas other groups increased (Proteobacteria of the subclasses alpha and gamma under benzalconiumchloride influence). By using different case examples in this thesis, it was possible to demonstrate the detection of the different physiological groups with rRNA-targeting oligonucleotides in the soil. In this manner the potential of molecular biological techniques (in-particular FISH) for the analysis of impurities in soil was demonstrated. T3 - BAM Dissertationsreihe - 3 KW - Biozidauswirkung KW - mikrobiologischen und molekularbiologischen Methoden PY - 2004 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1550 SN - 978-3-86509-201-2 SN - 1613-4249 VL - 3 SP - 1 EP - 168 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-155 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Lebid, Solomija T1 - Perturbations in behaviour of fibre Bragg grating sensors introduced by local thermal and mechanical influences N2 - Novel fibre optic sensor (FOS) systems maintaining fibre Bragg gratings (FBG) are finding wide application for health monitoring of large-scale structures such as dams, bridges, towers, as well as aircrafts, robots, automotive vehicles, and in composite technology. The principal advantage of such type of sensors is that the measured information is wavelength encoded (an absolute quantity). The main advantages include small size, immunity against electromagnetic field, good resolution, high sensitivity, and possibility to work in adverse environment. Especially small dimensions of the sensor allow its application for investigation of composite materials. The use of sensors enables to get information in areas, where other sensors would affect the structure or the material. On the other hand, it is important to keep signal stability of the sensor to the measured value of interest and obtain reliable data. Intimate embedment produces, however, additional perturbations affecting optical fibre sensor such as general mechanical stress, microbending, bending, and point-wise transverse load, which result in such undesirable sensor signal changes as attenuation, birefringence, spectrum broadening, sideband increasing, or small wavelength shift. No reliable knowledge about those effects and their consequences to the measured signal could be found in literature. This lack of knowledge led to the motivation of this work. The thesis discusses behaviour of uniform short-period fibre Bragg grating signal under before mentioned perturbing influences. The main accent is made onto theoretical and experimental study of additional mechanical perturbations: point-wise transverse indentation, and microbending, arising at sensor operation depending on the grating integration type and measurement purpose. Response of this type of gratings (unapplied and integrated in/on the object to be mesaured) to the axial strain and composite-integrated gratings to the temperature is also investigated. Problems arising from the sensor fixing on/in the object to be measured are considered. T3 - BAM Dissertationsreihe - 2 PY - 2004 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1568 SN - 978-3-86509-136-9 SN - 1613-4249 VL - 2 SP - 1 EP - 170 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-156 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Reusch, Frederik T1 - Entwicklung und Anwendung eines nicht-lokalen Materialmodells zur Simulation duktiler Schädigung in metallischen Werkstoffen N2 - Diese Arbeit umfasst die Entwicklung, Implementierung und Anwendung einer nicht-lokalen, gradientenabhängigen Erweiterung des lokalen Gurson-Modells zur Simulation duktiler Schädigung für metallische Werkstoffe, um die Anwendungsgrenzen lokaler Schädigungsmodelle im Rahmen der FE-Methode bzgl. Netzabhängigkeit und Lokalisierung von Simulationsergebnissen zu überwinden. Zu den offenen Problemen bei der Anwendung von lokalen, inelastischen Schädigungsmodellen gehört u. a. die Abhängigkeit der erzielten Ergebnisse von der Größe und Orientierung der zur Strukturdiskretisierung eingesetzten Finiten Elemente. Diese Netzabhängigkeit tritt insbesondere bei der Verwendung lokaler Stoffgesetze und der Simulation entfestigenden Materialverhaltens auf. Diese Beschränkungen lokaler Modelle sind maßgeblich auf den Eindeutigkeitsverlust der Lösung des Systems der konstitutiven Gleichungen durch die Modellierung von Entfestigungsvorgängen zurückzuführen. Ausgangspunkt für die Entwicklung einer nicht-lokalen Formulierung des Gurson- Modells stellt die Zielsetzung dar, die lokale Beschreibung der Schädigungsentwicklung durch die Evolutionsgleichung des Hohlraumvolumenanteils unter Berücksichtigung des Gradienten der räumlichen Schädigungsverteilung zu erweitern. T3 - BAM Dissertationsreihe - 1 KW - Schadensmechanik KW - Numerisches Modell KW - Duktilität KW - Rissausbreitung PY - 2003 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1573 SN - 978-3-86509-092-3 SN - 1613-4249 VL - 1 SP - 1 EP - 194 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-157 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -