TY - CONF A1 - Radnik, Jörg T1 - Colours, nano and surface N2 - The basic ideas of colours and pigments are presented. The correlation between nanomaterials and colours are explained. Different methods are presented for investigating nanoparticles and their surface. At the end a case study is presented explaining the importance of coating for the properties of nanoparticles. T2 - Eingeladener Vortrag im Deutschen Lackmuseum (Münster) CY - Online meeting DA - 11.02.2022 KW - Pigments KW - Surface Analytics KW - Coatings PY - 2022 AN - OPUS4-54376 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Géraldine A1 - Gradt, Thomas T1 - Influence of the counterface on the sliding behavior of polymer materials in hydrogen N2 - This presentation deals with the influence of the counterface materials on the sliding behaviour of some polymer materials in hydrogen. Polyimide (PI), polyetheretherketone (PEEK) and Polytetrafluoroethylene (PTFE) materials were investigated against hardened 52100 martensitic bearing steel and 304 austenitic stainless steel with similar roughness (Ra = 0.2 μm). Results indicate that the friction and wear of PI and PEEK materials depend on the counterface material. This effect wasn’t observed for PTFE composites. While the tribological performance of polyimide is better against 52100 in hydrogen, improved sliding behaviour of PEEK materials is observed with 304 counterface, particularly at higher sliding speed. Surface analyses of the transfer film reveal that the influence of the counterface is primarily related to the chemical nature of the steel for PI and to the thermal conductivity of the disc for PEEK materials. T2 - Hydrogenius & I2CNER Tribology Symposium CY - Online meeting DA - 29.01.2021 KW - Polymers KW - Hydrogen KW - Counterface KW - Friction KW - Wear PY - 2021 AN - OPUS4-52093 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Omar, Hassan A1 - Szymoniak, Paulina A1 - Hertwig, Andreas A1 - Schönhals, Andreas T1 - Invesitgation of Thin Film Interactions with Inorganic Surfaces N2 - Thin polymer films are of vital importance due to their low production costs and wide range of applications in sensors, electronics, and coatings. Their geometry is ideal for the study of confinement effects, specifically one-dimensional confinement, on the thermodynamic properties and segmental dynamics of polymers. For this investigation, films of PC are prepared on both glass and silica substrates to measure the dielectric and calorimetric behavior as a function of film thickness. The methodology consists of broadband dielectric spectroscopy (BDS), ellipsometry, and atomic force microscopy (AFM). Using ellipsometry, the glass transition shows an increase with decreasing film thickness. Compared to a previous investigation of PC where dilatometry was used, an increase in PC was seen, but now only at thicknesses below 20 nm. Therefore, the critical thickness of PC, where the bulk-like layer no longer percolates through the film, is dependent on the method probing the glass transition. The dielectric behavior shows a deviation from bulk behavior with decreasing film thickness, although still showing a Vogel-Fulcher-Tammann (VFT) temperature dependence for all films. The influence of the adsorbed layer on the molecular mobility was also addressed. T2 - Deutschen Physikalische Gesellschaft (DPG) Tagung CY - Regensburg, Germany DA - 04.09.2022 KW - Thin films KW - Adsorbed Layer KW - Broadband dielectric spectroscopy PY - 2022 AN - OPUS4-55706 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger T1 - Du kriegst die Motten I - Kleidermotten und Co. N2 - Vorkommen, Biologie und biologische Bekämpfung von Kleidermotten und Teppichkäfern werden vorgestellt. T2 - Fortbildungslehrgang für Schädlingsbekämpfer CY - Kempen, Germany DA - 21.05.2016 KW - Biologische Schädlingsbekämpfung KW - Kleidermotten KW - Teppichkäfer KW - Textilschutz PY - 2016 AN - OPUS4-36963 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Oertzen, Alexander T1 - Reporting of BAM, Explosives Division to the EU – HME Research Project and Activities of Forum of Notified Bodies for Explosives N2 - Work done by the forum of Notified Bodies for explosives, as reported by the chairman of the group, results, developments, and current research in the area of home made explosives. T2 - Meeting of the Working Group on Explosives for Civil Uses CY - Brussels, Belgium DA - 17.10.2016 KW - Notified body KW - Explosives KW - Home made explosives PY - 2016 AN - OPUS4-38017 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lexow, Jürgen T1 - IEA-IA-AMT Advanced materials for transport N2 - Materials properties strongly influence the energy combustion of vehicles. The IEA Technology Cooperation Program Advanced Materials for Transport presents its activity. T2 - IEA Transport Contact Group Meeting CY - Paris, France DA - 19.01.2016 KW - Internationale Energieagentur KW - Leightweighting KW - Globaler Kraftfahrzeugbestand KW - Treibhausgas KW - Internationale Zusammenarbeit KW - Total amout of cars in the world KW - International Energy Agency KW - Green house gas KW - International cooperation PY - 2016 AN - OPUS4-38023 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilrich, Cordula T1 - Einstufung von Gemischen ‒ Physikalische Gefahren N2 - Der Vortrag stellt die physikalischen Gefahrenklassen nach der CLP-Verordnung vor und geht auf mögliche Stratgeien bei der Einstufung ein. T2 - Veranstaltung "Gemische im Fokus: Herausforderungen durch Einstufung und Giftinformation meistern" des Helpdesks REACH-CLP-Biozid bei der BAuA CY - Dortmund, Germany DA - 20.05.2019 KW - Chemikalienrecht KW - UN-GHS KW - Einstufung KW - Gefährliche Stoffe KW - CLP-Verordnung KW - Physikalische Gefahren PY - 2019 AN - OPUS4-48059 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Pötzsch, S. A1 - Bäßler, Ralph T1 - Compatibility of polymers with aged heating oil containing 10 % and 20 % biodiesel under static conditions N2 - Biodiesel is viewed as a major source of energy. In areas such as the European Un-ion, where 80 % of the oil-based fuel is imported, there is also the desire to reduce dependence on external oil supplies. Materials compatibility is a major concern whenever the fuel composition is changed. The question arises of whether polymeric materials are resistant to heating oil with 20 % biodiesel (B20) in comparison to pure heating oil. The polarity of biodiesel increases its solvency and facilitates permeation and extrac-tion. Solvation, swelling and/or extraction lead to changes in the physical properties. Extraction alters the fuel chemistry. These chemical changes could also accelerate the degradation (hydrolysis and oxidation) of the polymeric material with the loss of additives and stabilizers. Exposure tests to determine the resistance of polymers frequently used for compo-nents in middle distillate facilities, such as ACM, FKM, HNBR, PA, PE, POM, PUR and PVC in heating oil and a blend of heating oil and 20 % biodiesel (B20) were al-ready performed. The objective of this research was to determine the resistance of these polymers in 8-year aged heating oil blend B10 and 1-year aged blend B20 at 40 °C. Mass, tensile strength, breaking elongation and Shore hardness A (D) of the test specimens were determined before and after exposure for 84 (42) days in the test fuels under static conditions. There is not determined a threshold for the reduction in tensile properties and Shore hardness in the international standards. Therefore, a threshold of 15 % was deter-mined for the evaluation of the compatibility. A significant reduction in Shore hardness was determined after exposure of ACM and PUR test specimens in 1-year aged B20. The tensile strength of PUR test specimens in 1-year aged B20 was reduced by more than 50 %, and the breaking elongation by more than 30 %. A decrease in breaking elongation was measured for POM test specimens after ex-posure to 1-year aged B20 by 25 % (limited resistance). 8-year aged B10 had a stronger effect than 1-year aged B20 on the polymers. ACM test specimens were softened by B10 resulting in a drop of Shore hardness by over 20 %. B10 reduced tensile strength and breaking elongation of PUR test specimens by over 50 %. In contrast, the breaking elongation of POM was increased by over 270 %. It can be concluded that the polymers HNBR, FKM, PA6, PE and PVC are resistant in 1-year aged B20 whereas ACM and POM are limited resistant. PUR is not re-sistant. HNBR, FKM, PA6, PE and PVC are resistant in 8-year aged B10, whereas PUR and POM are not resistant, and ACM just limited resistant. T2 - EUROCORR 2020 CY - Online meeting DA - 07.09.2020 KW - Aged heating oil with 10% and 20% biodiesel KW - Resistance of polymers KW - Tensile properties KW - Shore hardness PY - 2020 AN - OPUS4-51240 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Askar, Enis A1 - Abdelkhalik, A. A1 - Brandes, E. A1 - Markus, D. A1 - Stolz, Th. T1 - Berechnung der Explosionsbereiche von Alkoholen, Ketonen und halogenierten Kohlenwasserstoffen im Gemisch mit Inertgasen N2 - Ergänzend zu früheren Arbeiten. in denen die Explosionsbereiche für Brenngase aus der homologen Reihe der Alkane und Alkene berechnet worden sind, wurden Ergebnisse der Berechnungen für 1-Propanol, Aceton und Difluormethan vorgestellt. Für die Berechnung ist das Modell erweitert worden. so dass auch die Transporteigenschaften der Gasgemische berücksichtigt werden. Weiterhin ist eine neue Methode zur Berechnung der Spitze des Explosionsbereichs implementiert worden. Die Ergebnisse zeigen. dass die Berechnung der Explosionsbereiche für Alkohole. Ketone und halogenierte Kohlenwasserstoffe mit ähnlicher Genauigkeit wie für Alkane und Alkene möglich ist. T2 - 15. BAM-PTB-Kolloquium 2019 CY - Braunschweig, Germany DA - 21.05.2019 KW - Explosionsgrenzen KW - Inertisierung KW - Modell der konstanten Flammentemperaturen KW - Explosionsschutz PY - 2019 AN - OPUS4-48542 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Bernd R. A1 - Bruno, Giovanni T1 - Absorption and refraction techniques: Characterization and Non-Destructivetesting of materials N2 - X-ray techniques developed and used in BAM FB 8.5 (Micro NDE) for characterization of ceramic materials. T2 - Sitzung der Technischen Kommission des Verbands der Keramischen Industrie CY - Berlin, Gremany DA - 10.3.2017 KW - X-ray KW - X-ray refraction KW - Computed Tomography PY - 2017 AN - OPUS4-39322 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -