TY - CONF A1 - von der Au, Marcus T1 - HR-CS-GF-MAS as a new screening method for emerging pollutants - per- and polyfluorinated substances in the environment N2 - The introduction of fluorine in organic molecules leads to new chemical/physical properties. Especially in the field of pharmaceuticals, fluorinated organic molecules are becoming more and more popular and at present amount up to 25% of market share, with an upward trend. The main benefits of fluorinated pharmaceuticals are: (i) enhanced fat solubility; (ii) enhanced interaction of catalytic-center of enzymes with fluorine-drugs; (iii) a delayed metabolism within the human body. Highly fluorinated organic substances are also used in technical applications (e.g. coatings, fire-extinguishing agents). Due to the broad variety of fluorinated substances and increasing production volumes numerous and up to date unknown fluorine-species are most likely to be present in the (aquatic) environment. Analytical methods to assess the degree of contamination of surface waters with organically bound fluorine are highly needed and up to now only combustion ion chromatography based method is available, which is relatively laborious. Since a few years’ high resolution-continuum source-graphite furnace atomic absorption spectrometers (HR-CS-GFAAS) are commercially available from Analytik Jena. By means of this technique, the detection of high resolution molecular absorption spectra (MAS) is enabled. Thus, fluoride is detectable upon the addition of a modifier and the formation of a diatomic molecule (e.g. GaF). Just recently, we applied this technique for total fluorine (mainly dissolved fluoride) analysis in river water samples. In the present work a HR-CS-GFMAS method for extractable organically bound fluorine (EOF) analysis in surface water samples was developed by us. The method is based on SPE extraction of organically bound fluorine even in the presence of high fluoride concentrations followed by HR-CS-GFMAS analysis upon elution. Due to high enrichment factors, LODs in the low ng/L range were achieved. We successfully applied our SPE HR-CS-GFMAS method to Rhine water samples and EOF in the range of about 50-300 ng/L was detectable. T2 - DGMS 2020 CY - Münster, Germany DA - 01.03.2020 KW - SPE HR-CS GF MAS PY - 2020 AN - OPUS4-50503 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von der Au, Marcus T1 - HR-CS-GF-MAS as a new screening method for emerging pollutants - per- and polyfluorinated substances in the environment N2 - The introduction of fluorine in organic molecules leads to new chemical/physical properties. Especially in the field of pharmaceuticals, fluorinated organic molecules are becoming more and more popular and at present amount up to 25% of market share, with an upward trend. The main benefits of fluorinated pharmaceuticals are: (i) enhanced fat solubility; (ii) enhanced interaction of catalytic-center of enzymes with fluorine-drugs; (iii) a delayed metabolism within the human body. Highly fluorinated organic substances are also used in technical applications (e.g. coatings, fire-extinguishing agents). Due to the broad variety of fluorinated substances and increasing production volumes numerous and up to date unknown fluorine-species are most likely to be present in the (aquatic) environment. Analytical methods to assess the degree of contamination of surface waters with organically bound fluorine are highly needed and up to now only combustion ion chromatography based method is available, which is relatively laborious. Since a few years’ high resolution-continuum source-graphite furnace atomic absorption spectrometers (HR-CS-GFAAS) are commercially available from Analytik Jena. By means of this technique, the detection of high resolution molecular absorption spectra (MAS) is enabled. Thus, fluoride is detectable upon the addition of a modifier and the formation of a diatomic molecule (e.g. GaF). Just recently, we applied this technique for total fluorine (mainly dissolved fluoride) analysis in river water samples. In the present work a HR-CS-GFMAS method for extractable organically bound fluorine (EOF) analysis in surface water samples was developed by us. The method is based on SPE extraction of organically bound fluorine even in the presence of high fluoride concentrations followed by HR-CS-GFMAS analysis upon elution. Due to high enrichment factors, LODs in the low ng/L range were achieved. We successfully applied our SPE HR-CS-GFMAS method to Rhine water samples and EOF in the range of about 50-300 ng/L was detectable. T2 - DGMS 2020 CY - Münster, Germany DA - 01.03.2020 KW - SPE HR-CS GF MAS PY - 2020 AN - OPUS4-50504 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Adamczyk, Burkart A1 - Neuhold, S. A1 - Drissen, P. A1 - Algermissen, D. A1 - Presoly, P. A1 - Sedlazeck, K. P. A1 - Schenk, J. A1 - Raith, J. G. A1 - Pomberger, R. A1 - Vollprecht, D. T1 - Tailoring the FeO/SiO2 ratio in electric arc furnace slags to minimize the leaching of Vanadium and Chromium N2 - Based on recently published research on leaching control mechanisms in electric arc furnace (EAF) slags, it is assumed that a FeO/SiO2 ratio of around one leads to low leached V and Cr concentrations. This ratio influences the mineral phase composition of the slag toward higher amounts of spinel and a lower solubility of calcium silicate phases by suppressing the formation of magnesiowuestite and highly soluble calcium silicate phases. To evaluate this hypothesis, laboratory and scaled up tests in an EAF pilot plant were performed on slag samples characterized by elevated V and Cr leaching and a high FeO/SiO2 ratio. Prior to the melting experiments, the optimum FeO/SiO2 ratio was calculated via FactSageTM. In the melting experiments, the ratio was adjusted by adding quartz sand, which also decreased the basicity (CaO/SiO2) of the slag. As a reference, remelting experiments without quartz sand addition were conducted and additionally, the influence of the cooling rate of the slag was examined. The remelted (without quartz sand) and the remelted modified slags (with quartz sand) were analyzed chemically and mineralogically and the leaching behavior was investigated. The modification of the slags yielded a minimized release of V and Cr, supporting the hypothesis that the FeO/SiO2 ratio influences the mineralogy and the leaching behavior. KW - Electric arc furnace slags KW - FactSage calculations KW - EAF slags KW - Leaching control mechanisms KW - Melting experiments PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-507748 DO - https://doi.org/10.3390/app10072549 VL - 10 IS - 7 SP - 2549 EP - 2565 AN - OPUS4-50774 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Neumann, Patrick P. A1 - Hirschberger, Paul A1 - Bartholmai, Matthias ED - Zemčík, R. ED - Krystek, J. T1 - Influence of rotor downwash on vertically displaced nanobots in flight N2 - One challenge associated with navigating a nano aerial robot swarm indoors in unstructured environments is, i.a., the limited air space. To avoid an over-regulation of the available indoor air space (e.g., prohibit copters to fly above each other), a safety region around each copter must be defined. In this paper, we investigate the impact of the downwash of a nano-drone on the stability of another nearby nano-drone. In the experiments, we found out that this downwash has a negative influence of a second nano-drone in a distance of around 1 m vertically and 0.2 m horizontally. Based on the obtained data, we developed a model describing the above-mentioned safety region to enable a safe operation of the swarm in these environments with fewer constraints. T2 - 36th Danubia-Adria Symposium on Advances in Experimental Mechanics CY - Pilsen, Czech Republic DA - 24.09.2019 KW - Mobile Robot Olfaction KW - Nano aerial robot KW - Swarm KW - Collision-free navigation KW - Safety region model PY - 2020 DO - https://doi.org/10.1016/j.matpr.2020.03.047 VL - 32 IS - 2 SP - 108 EP - 111 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-50673 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vandrich, Jasmina A1 - Pfeiffer, F. A1 - Alfaro Espinoza, Gabriela A1 - Kunte, Hans-Jörg T1 - Contribution of mechanosensitive channels to osmoadaptation and ectoine excretion in Halomonas elongata N2 - For osmoadaptation the halophilic bacterium Halomonas elongata synthesizes as its main compatible solute the aspartate derivative ectoine. H. elongata does not rely entirely on synthesis but can accumulate ectoine by uptake from the surrounding environment with the help of the osmoregulated transporter TeaABC. Disruption of the TeaABC-mediated ectoine uptake creates a strain that is constantly losing ectoine to the medium. However, the efflux mechanism of ectoine in H. elongata is not yet understood. H. elongata possesses four genes encoding mechanosensitive channels all of which belong to the small conductance type (MscS). Analysis by qRT-PCR revealed a reduction in transcription of the mscS genes with increasing salinity. The response of H. elongata to hypo- and hyperosmotic shock never resulted in up-regulation but rather in downregulation of mscS transcription. Deletion of all four mscS genes created a mutant that was unable to cope with hypoosmotic shock. However, the knockout mutant grew significantly faster than the wildtype at high salinity of 2 M NaCl, and most importantly, still exported 80% of the ectoine compared to the wildtype. We thus conclude that a yet unknown system, which is independent of mechanosensitive channels, is the major export route for ectoine in H. elongata. KW - Halomonas elongata KW - Ectoine KW - Osmotic shock KW - Solute excretion KW - Osmoadaptation KW - Mechanosensitive channel KW - MscS PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-507229 DO - https://doi.org/10.1007/s00792-020-01168-y VL - 24 SP - 421 EP - 432 PB - Springer AN - OPUS4-50722 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Söftje, M. A1 - Acker, S. A1 - Plarre, Rüdiger A1 - Namyslo, J. C. A1 - Kaufmann, D. E. T1 - Novel nicotinoid structures for covalent modification of wood: an environmentally friendly way for its protection against insects N2 - Timber is constantly exposed to environmental influences under outdoor conditions which limits its Lifetime and usability. In order to counteract the damaging processes caused by insects, we have developed a novel and more environmentally friendly method to protect wood materials via covalent modification by organic insecticides. Starting with an important class of synthetic insecticides which are derived from the natural insecticide nicotine, various new carboxylic acid derivatives of imidacloprid were made accessible. These activated neonicotinoids were utilized for the chemical modification of wood hydroxy groups. In contrast to conventional wood preservation methods in which biocides are only physically bound to the surface for a limited time, the covalent fixation of the preservative guarantees a permanent effect against wood pests, demonstrated in standardized biological tests. Additionally, the environmental interaction caused by non-bound neonicotinoids is significantly reduced, since both, a smaller application rate is required and leaching of the active ingredient is prevented. By minimizing the pest infestation, the lifetime of the material increases while preserving the natural appearance of the material. KW - Environment KW - Wood Protection KW - Efficacy KW - Insecticide PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-506856 DO - https://doi.org/10.1039/d0ra02071k VL - 10 SP - 15726 EP - 15733 AN - OPUS4-50685 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger ED - Trematerra, P. ED - Conti, B. T1 - Uninvited and welcomed guests in museums – biological management of clothes moths and woodworms N2 - In museums and historic houses clothes, moths (Tineola bisselliella, Tinea pellionella) and the furniture beetle (Anobium punctatum) are the most economically important pests on textiles or wooden artifacts, respectively. Their management is essential to protect cultural ethnological heritage and natural history collections for future generations. Pest management strategies have changed over time. Today, intensive knowledge on pest biology and overall material science are key cornerstones in IPM concepts - also for the Museum environment. The important first steps for sustainable pest management are risk assessment, early pest detection and identification of pathways of infestation. These steps are followed by physical and biological means of control, which have lately gained more importance than applying biocides. Several potentially effective biological enemies of clothes moths and woodworm have been known for a long time, but their promotion for pest control in Museums and historic houses is just beginning. This short review summarizes current concepts of pest life cycle interruption by applying good quarantine and very specific biological measures. The lessons learned from recent faunistic surveys, life-history studies as well as behavioral observations of parasitoids and predators of clothes moths and woodworm may supplement the pest management tool box. The need for further research in this field is addressed. T2 - Working Group Meeting "Integrated Protection of Stored Products" CY - Pisa, Italy DA - 03.09.2019 KW - Corynetes caeruleus KW - Biological control KW - Museum pests KW - Tineola bisselliella KW - Anobium punctatum KW - Apanteles carpatus KW - Baryscapus tineivorus PY - 2020 SN - 978-92-9067-333-0 VL - 148 SP - 266 EP - 273 AN - OPUS4-50543 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Blasenbauer, D. A1 - Huber, F. A1 - Lederer, J. A1 - Quina, M. A1 - Blanc-Biscarat, D. A1 - Bogush, A. A1 - Bontempi, E. A1 - Blondeau, J. A1 - Chimenos, J. A1 - Dahlbo, H. A1 - Fagerqvist, J. A1 - Giro-Paloma, J. A1 - Hjelmar, O. A1 - Hyks, J. A1 - Keaney, J. A1 - Lupsea-Toader, M. A1 - O’Caollai, C. A1 - Orupõld, K. A1 - Pajak, T. A1 - Simon, Franz-Georg A1 - Svecova, L. A1 - Syc, M. A1 - Uvang, R. A1 - Vaajasaari, K. A1 - van Caneghem, J. A1 - van Zomeren, A. A1 - Vasarevičius, S. A1 - Wégner, K. A1 - Fellner, J. T1 - Legal situation and current practice of waste incineration bottom ash utilisation in Europe N2 - Almost 500 municipal solid waste incineration plants in the EU, Norway and Switzerland generate about 17.6 Mt/a of incinerator bottom ash (IBA). IBA contains minerals and metals. Metals are mostly separated and sold to the scrap market and minerals are either disposed of in landfills or utilised in the construction sector. Since there is no uniform regulation for IBA utilisation at EU level, countries developed own rules with varying requirements for utilisation. As a result from a cooperation network between European experts an up-to-date overview of documents regulating IBA utilisation is presented. Furthermore, this work highlights the different requirements that have to be considered. Overall, 51 different parameters for the total content and 36 different parameters for the emission by leaching are defined. An analysis of the defined parameter reveals that leaching parameters are significantly more to be considered compared to total content parameters. In order to assess the leaching behaviour nine different leaching tests, including batch tests, up-flow percolation tests and one diffusion test (monolithic materials) are in place. A further discussion of leaching parameters showed that certain countries took over limit values initially defined for landfills for inert waste and adopted them for IBA utilisation. The overall utilisation rate of IBA in construction works is approximately 54 wt%. It is revealed that the rate of utilisation does not necessarily depend on how well regulated IBA utilisation is, but rather seems to be a result of political commitment for IBA recycling and economically interesting circumstances. KW - Bottom ash KW - Leaching tests KW - Utilisation PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-500161 DO - https://doi.org/10.1016/j.wasman.2019.11.031 SN - 0956-053X VL - 102 SP - 868 EP - 883 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-50016 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Raysyan, Anna T1 - Determination of mycotoxins in food and pharmaceuticals by immunochemical analysis N2 - Mycotoxins are toxic secondary metabolites produced by filamentous fungi. The contamination of mycotoxins in food and feed products has been recognized to be an important safety issue for human and animal health. In the context of food safety, medical herbs nowadays are also considered as potential source of mycotoxins. Considering that mycotoxins are generally stable compounds and could not be destroyed completely during food-processing operations, prevention of contamination is identified as main issue. Currently, biochemical, and immunochemical methods based on the use of antibodies as a specific recognition bioreagents are increasingly found to be applied in screening. Along with good common enzyme linked immunosorbent assay (ELISA), more and more widely used method is fluorescence polarization immunoassay (FPIA). These methods help to monitor of many toxic substances in large number of samples and carried out quickly, easily, cheaply, and give good results in quantifying the one or more substances. That is why the use of immunochemical methods of analysis, such as ELISA and FPIA, is the most promising for solving this problem. Thus, the aim of our work is to optimize the determination of mycotoxins by ELISA and FPIA in medical herbs. We selected antibodies and a tracer for the FPIA, then we constructed obtained a calibration curve and determined the sensitivity of this method for the samples in aqueous media. Then, the optimal sample preparation was elaborated: for spiked nuts samples were selected and prepared and a calibration curve was obtained with respect to the matrix effect. After that, the analysis of spiked nuts samples was performed by ELISA and FPIA and the sensitivity of both methods was compared. T2 - Global Food Science Student Competition CY - Jiangnan University, Wuxi, China DA - 14.11.2018 KW - Mycotoxins KW - FPIA KW - ELISA PY - 2018 AN - OPUS4-50048 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zimmermann, T. A1 - von der Au, Marcus A1 - Reese, A. A1 - Klein, O. A1 - Hildebrandt, L. A1 - Pröfrock, D. T1 - Substituting HF by HBF4 – an optimized digestion method for multi-elemental sediment analysis via ICP-MS/MS N2 - Determination of elemental mass fractions in sediments plays a major role in evaluating the environmental status of aquatic ecosystems. Herewith, the optimization of a new total digestion protocol and the subsequent analysis of 48 elements in different sediment reference materials (NIST SRM 2702, GBW 07313, GBW 07311 and JMC-2) based on ICP-MS/MS detection is presented. The developed method applies microwave acid digestion and utilizes HBF4 as fluoride source for silicate decomposition. Similar to established protocols based on HF, HBF4 ensures the dissolution of the silicate matrix, as well as other refractory oxides. As HBF4 is not acutely toxic; no special precautions have to be made and digests can be directly measured via ICP-MS without specific sample inlet systems, evaporation steps or the addition of e.g. H3BO3, in order to mask excess HF. Different acid mixtures with and without HBF4 were evaluated in terms of digestion efficiency based on the trace metal recovery. The optimized protocol (5 mL HNO3, 2 mL HCL, 1 mL HBF4) allows a complete dissolution of the analyzed reference materials, as well as quantitative recoveries for a wide variety of certified analytes. Low recoveries for e.g. Sr, Ba and rare earth elements due to fluoride precipitation of HF-based digestions protocols, can be avoided by the usage of HBF4 instead. Based on the usage of high purity HBF4 all relevant trace, as well as matrix elements can be analyzed with sufficiently low LOQs (0.002 μg L−1 for U up to 6.7 μg L−1 for Al). In total, 34 elements were within a recovery range of 80%–120% for all three analyzed reference materials GBW 07313, GBW 07311 and JMC-2. 14 elements were outside a recovery range of 80%–120% for at least one of the analyzed reference materials. KW - Reference Materials KW - Sediment KW - HF free Digestion PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-510480 DO - https://doi.org/10.1039/D0AY01049A SP - 1 EP - 10 PB - Royal Society of Chemistry AN - OPUS4-51048 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Axel T1 - Analysis of tire wear particles in soil samples from roadside using TED-GC/MS N2 - Tire wear particles (TW) are generated by the abrasions of tires on the road surface through traffic. These particles can be transported by air and surface runoff and might also infiltrate the soil and consequently affect terrestrial ecosystems. The estimated tire wear (TW) emissions are immense, with 1.33 106 t a-1 in Europe. Despite this, only little is known about the environmental contents or the fate of TW. One reason for this knowledge gap is the challenging analysis of TW in environmental samples. Detection of TW with spectroscopic methods is problematic due to high fluorescence interferences caused by contained black carbon. One analytical approach is to use zinc (Zn), a typical additive in tires, as a specific marker for the quantification of tire wear. However, any Zn originating from the sample matrix must be separated beforehand and requires elaborate sample preparation. Car tires consist partly of synthetic rubbers, such as styrene-butadiene-rubber (SBR). This SBR could be identified and quantified via Thermal-Extraction-Desorption-Gas Chromatography-Mass Spectrometry (TED-GC-MS). This newly developed and fast screening method allows the simultaneous detection of microplastics and TW mass contents and requires minimal to no sample preparation. Firstly the sample is thermally extracted in a thermobalance under a nitrogen atmosphere. The resulting specific decomposition products are sorbed on a solid phase adsorber, which is then transferred to a GC-MS via an autosampler, where the products are desorbed, separated and identified. Cyclohexenylbenzene is used as a specific marker for SBR. Here we investigated top layer soil samples, collected at the roadside of highly frequented German highways. Samples were analyzed without sample preparation, and SBR was detected in all investigated samples in mass contents ranging from 67.2 to 2230 mg kg-1. A correlation between SBR and Zn content in the soil was confirmed, while the correlation between SBR and Corg was hardly pronounced. We successfully demonstrated the application of TED-GC-MS as a screening method for tire wear in soil samples. The present study will discuss these analytical results in detail as well as sampling parameters like sampling depth and distance to the roadside, and the effect of the particle size on the particle transport by water runoff and air. T2 - SETAC 2020 SciCon CY - Online meeting DA - 03.05.2020 KW - Microplastic KW - Analysis KW - Tire wear KW - Soil PY - 2020 AN - OPUS4-51086 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Natsopoulou, M.E. A1 - McMahon, Dino Peter A1 - Paxton, R.J. T1 - Parasites modulate within-colony activity and accelerate the temporal polyethism schedule of a social insect, the honey bee N2 - Task allocation in social insect colonies is generally organised into an age-related division of labour, termed the temporal polyethism schedule, which may in part have evolved to reduce infection of the colony's brood by pests and pathogens. The temporal polyethism schedule is sensitive to colony perturbations that may lead to adaptive changes in task allocation, maintaining colony homeostasis. Though social insects can be infected by a range of parasites, little is known of how these parasites impact within-colony behaviour and the temporal polyethism schedule. We use honey bees (Apis mellifera) experimentally infected by two of their emerging pathogens, Deformed wing virus (DWV), which is relatively understudied concerning its behavioural impact on its host, and the exotic microsporidian Nosema ceranae. We examined parasite effects on host temporal polyethism and patterns of activity within the colony. We found that pathogens accelerated the temporal polyethism schedule, but without reducing host behavioural repertoire. Infected hosts exhibited increased hyperactivity, allocating more time to self-grooming and foraging-related tasks. The strength of behavioural alterations we observed was found to be pathogen specific; behavioural modifications were more pronounced in virus-treated hosts versus N. ceranae-treated hosts, with potential benefits for the colony in terms of reducing within-colony transmission. Investigating the effects of multiple pathogens on behavioural patterns of social insects could play a crucial role in understanding pathogen spread within a colony and their effects on colony social organisation. KW - Host KW - Pathogen KW - Multiple infection KW - Apis mellifera KW - Nosema ceranae KW - Deformed wing virus PY - 2016 DO - https://doi.org/10.1007/s00265-015-2019-5 SN - 0340-5443 SN - 1432-0762 VL - 70 IS - 7 SP - 1019 EP - 1031 PB - Springer CY - Berlin ; Heidelberg [u.a.] AN - OPUS4-34738 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Schoknecht, Ute A1 - Mathies, Helena A1 - Wegner, R. A1 - Uhlig, S. A1 - Baldauf, H. A1 - Colson, B. T1 - Emissions of material preservatives into the environment - realistic extimation of environmental risks through the improved characterisation of the leaching of biocides from treated materials used outdoors N2 - This report supports the implementation of European regulations on biocidal products for the product types 7, 9 and 10. Emission of active substances from material preservatives into environmental compartments can occur due precipitation. Risk characterisations have to be based on estimations of environmental concentrations of target substances leached from material preservatives. Harmonised test procedures are required to predict environmental impact due to leaching. Seventeen treated articles, mainly paints, but also a textile, sealing tapes and sealing masses were investigated by intermittent contact to water to prove suitability of the proposed laboratory test procedure. Parameters that affect leaching of active substances were examined. Further development of a semi-analytical model to describe laboratory leaching data revealed that the model can be improved if changes of the leachability of substances during the test are supposed and integrated. Six paints and a textile were exposed to weathering to compare results from laboratory and field experiments. Similarities between leaching processes in both test approaches were observed. Generally, emissions of active substances are considerably higher in laboratory tests than from vertically installed test specimens exposed to weathering. Competing processes that cause losses of active substances can occur in both tests, but to a higher degree in field experiments. In addition, the influence of meteorological parameters on leaching processes was investigated. Factors besides the amount of driving rain were identified that effect leaching processes by complex interaction. Relations between laboratory and field data were analysed, and the applicability of the semi-analytical model was tested for field data. Guidance documents for leaching tests under laboratory and field conditions were drafted and discussed with experts on EU Level workshop 3./4. July 2014, BAM, Berlin), and are included in this Report. N2 - Dieser Bericht unterstützt die Umsetzung europäischer Regelungen für Biozidprodukte der Produkttypen 7, 9 und 10. Die Freisetzung von Wirkstoffen aus Materialschutzmitteln in Umweltkompartimente kann bei Niederschlagsereignissen auftreten. Risikocharakterisierungen müssen auf Abschätzungen von Umweltkonzentrationen der betrachteten Stoffe basieren. Harmonisierte Testverfahren sind erforderlich, um eine Beeinflussung der Umwelt durch Auswaschung vorherzusagen. Siebzehn behandelte Waren, vor allem Farben, aber auch ein Textil, Dichtungsbänder und Dichtungsmassen wurden bei periodischem Wasserkontakt untersucht, um die Anwendbarkeit des vorgeschlagenen Laborverfahrens nachzuweisen. Faktoren, die Einfluss auf die Auswaschung von Wirkstoffen haben, wurden untersucht. Die Wieterentwicklung eines semianalytischen Modells zur Beschreibung von Auswaschdaten aus Laborversuchen ergab, dass das Modell verbessert werden kann, wenn eine Änderung der Auswaschbarkeit von Substanzen während des Versuchs angenommen und einbezogen wird. Sechs Farben und ein Textil wurden der Witterung ausgesetzt, um Ergebnisse aus Labor- und Freilandversuchen zu vergleichen. Zwischen Auswaschprozessen in beiden Versuchsansätzen wurden Ähnlichkeiten beobachtet. Im Allgemeinen sind die Emissionen von Wirkstoffen im Laborversuch deutlich höher als bei vertikal installierten bewitterten Prüfkörpern. Konkurrierende Prozesse, die Verluste an Wirkstoffen bewirken, können in beiden Testverfahren auftreten, sind aber im Freilandversuch stärker ausgeprägt. Außerdem wurde der Einfluss von meteorologischen Parametern auf Auswaschprozesse untersucht. Es wurden Faktoren identifiziert, die zusätzlich zur Schlagregenmenge durch komplexe Interaktion auf Auswaschprozesse wirken. Beziehungen zwischen Labor- und Frei-landdaten wurden analysiert und die Anwendbarkeit des semianalytischen Modells für Freilanddaten getestet. Leitfäden für Auswaschversuche unter Labor-bzw. Freilandbedingungen wurden entworfen, mit europäischen Experten diskutiert (Workshop 3./4. Juli 2014, BAM, Berlin) und sind Bestandteil dieses Berichts. KW - EU Biocides Regulation KW - Leaching tests KW - Treated articles KW - Modelling KW - EU-Biozidverordnung KW - Auswaschversuche KW - Behandelte Waren KW - Modellierung PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-355139 SN - 1862-4804 SP - 1 EP - 136 AN - OPUS4-35513 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Holm, Olaf A1 - Rein, A. A1 - Trapp, S. A1 - Popp-Hoffmann, S. A1 - Bittens, M. A1 - Leven, C. A1 - Dietrich, P. T1 - Comparison of phytoscreening and direct-push-based site investigation at a rural megasite contaminated with chlorinated ethenes N2 - The reliable characterization of subsurface contamination of spatially extended contaminated sites is a challenging task, especially with an unknown history of land use. Conventional technologies often fail due to temporal and financial constraints and thus hinder the redevelopment of abandoned areas in particular. Here we compare two site screening techniques that can be applied quickly at relatively low cost, namely Direct Push (DP)-based groundwater sampling and tree core sampling. The effectiveness of both methods is compared for a rural megasite contaminated with chlorinated hydrocarbons. Unexpected pollution hot spots could be identified using both of these methods, while tree coring even enabled the delineation of the contaminant plume flowing into an adjacent wetland inaccessible for DP units. Both methods showed a good agreement in revealing the spatial pattern of the contamination. The correlation between groundwater concentrations and equivalent concentrations in wood was linear and highly significant for trichloroethene. Correlation was less obvious for its metabolite cis-dichloroethene, but still significant. As outcome of our study we recommend tree coring and for initial screening in combination with a DP sampling to retrieve quantitative data on groundwater pollutants in order to assess the contamination situation of a non- or only partly investigated site. The subsequent placement of monitoring wells for long-term monitoring of contamination levels is recommended. A combination of methods would achieve more relevant information at comparable or possibly even lower efforts in comparison to a conventional site investigation. KW - non-invasive investigation KW - phytoscreening KW - direct-push KW - screening KW - trichloroethene KW - trichloroethylene KW - groundwater contamination KW - tree core sampling PY - 2015 UR - http://onlinelibrary.wiley.com/doi/10.1111/gwmr.12122/abstract DO - https://doi.org/10.1111/gwmr.12122 SN - 1745-6592 VL - 35 IS - 4 SP - 45 EP - 56 PB - Wiley Online Library AN - OPUS4-35595 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Barthel, Anne-Kathrin A1 - Wesch, Ch. A1 - Braun, Ulrike A1 - Klein, R. A1 - Paulus, M. T1 - No microplastics in benthic eelpout (Zoarces viviparus): An urgent need for spectroscopic analyses in microplastic detection N2 - Monitoring the ingestion of microplastics is challenging and suitable detection techniques are insufficiently used. Thus, misidentifying natural for synthetic microfibres cannot be avoided. As part of a framework to monitor the ingestion of microplastics in eelpout, this short report addresses the accurate identification of microfibres. We show that, following visual inspections, putatively synthetic microfibres are indeed of natural origin, as ascertained by spectrometric analyses. Consequently, we call for an inclusion of spectroscopic techniques in standardized microplastic monitoring schemes. KW - Monitoring KW - Ingestion KW - Misidentification KW - Microfibre KW - Spectroscopy PY - 2016 DO - https://doi.org/10.1016/j.envres.2016.03.017 SN - 0013-9351 VL - 148 SP - 36 EP - 38 PB - Elsevier AN - OPUS4-35603 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleis, Markus A1 - Gehrmann, Hans-Joachim A1 - Simon, Franz-Georg T1 - VDI-Richtlinie 3925 – Anwendung auf zwei Fallbeispiele N2 - Die VDI-Richtlinie 3925 entstand aus Diskussionen und Fragestellungen, die sich aus der Anwendung unterschiedlichster Methoden zur Bewertung verschiedener Verfahrenskonzepten aus dem Bereich der Abfallbehandlung ergeben haben. Je nach nachdem, wo der Focus der vorzunehmenden Bewertung liegt, wird sich die Methodik an diese Ziele anpassen oder - falls es die entsprechende Methodik noch nicht geben sollte - sich die Fragestellung anpassen müssen. T2 - ProcessNet Jahrestreffen CY - Frankfurt/Main DA - 23.02.2016 KW - Wirkungsgrad KW - Exergie KW - Abfallbehandlung KW - Ökobilanz PY - 2016 SP - 25 EP - 26 PB - ProcessNet CY - Frankfurt/Main AN - OPUS4-35506 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Holm, Olaf T1 - Reduction of natural resource use by improving resource efficiency N2 - Improving resource efficiency at the end-of-life stage is illustrated in this paper by the example of materials recovery from waste, here from residues out of municipal solid waste incineration (MSWI). With mechanical treatment valuable materials like ferrous and non-ferrous metals and secondary construction material can be extracted from MSWI bottom ash. The potential contribution on the resource efficiency will be discussed. T2 - 12th International Conference on Ecomaterials CY - Tainan, Taiwan DA - 08.11.2015 KW - secondary raw material KW - resource efficiency KW - raw material equivaltent KW - bottom ash PY - 2015 SP - 5 EP - 6 AN - OPUS4-35509 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Wilhelm T1 - Korrosion in Trinkwasserinstallationen N2 - Überblick über das Verhalten und mögliche Schadensszenarien von metallenen Werkstoffen im Kontakt mit Trinkwasser. Insbesondere auch die Abgabe von Stoffen aus den Werkstoffen an das Wasser wird diskutiert, daneben auch Schäden, die zum austritt von Wasser aus den Anlagen führen. T2 - Wehrtechnisches Symposium der Bundeswehr: Wassertechnik und Hygiene CY - Mannheim, Germany DA - 14.03.2016 KW - Trinkwasser KW - Korrosion KW - Metallabgabe PY - 2016 AN - OPUS4-35567 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dengel, Jörg A1 - Lohrer, Christian A1 - Stein, F. A1 - Perriam, J. T1 - Investigations on aerosol emissions of pyrotechnic smoke generators N2 - Pyrotechnic smoke generators fall under the Directive 2013/29/EU in Europe and could potentially belong to all categories except consumer fireworks. These types are especially present in the field of “Other Pyrotechnic Articles” of the categories P1 and P2, e.g. as simulation devices for paintball or airsoft gaming. The specific users of these products are aware of the corresponding smoke liberation during use and usually wear protective equipment to minimize exposure to potentially harmful aerosols. However, such products are often misused against the labelling requirements in locations where these articles are not supposed to be used, like football stadiums and demonstrations. In contrast to the intended use, uninvolved third parties are likely exposed to these reaction products without proper protective equipment. This study aims at identifying the transient particle size range of the aerosols emitted during the functioning of such common smoke generators for simulation purposes. In total four different types of articles were investigated, with five colors per type (white, blue, green, red, orange). Results show that the majority of the particles were emitted in a range between 40 nm and 350 nm, with some variation depending on the smoke color. Particles with diameters of less than 100 nm are generally of specific concern, as they can penetrate the alveolar system of the human lungs and therefore present a specific hazard. KW - FMPS KW - Simulation devices PY - 2016 VL - 2016 IS - 35 SP - 3 EP - 8 PB - Journal of Pyrotechnics CY - Cambridgeshire (UK) AN - OPUS4-35742 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Oliver T1 - Recycled fertilizers: Do we need new regulations and analytical methods? N2 - More and more fertilizers emerge from recycled waste materials. This requires new analytical methods and/or the adaption of existing ones to new materials and matrices. KW - Environmenatal analysis KW - Resource recovery KW - Fertilizer PY - 2016 UR - http://www.sciencedirect.com/science/article/pii/S0956053X16000398 DO - https://doi.org/10.1016/j.wasman.2016.03.017 SN - 0956-053X VL - 50 SP - 1 EP - 2 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-35654 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Merryweather, S. A1 - Zweifel, D. A1 - Woydt, Mathias ED - Franek, F. ED - Bartz, Wilfried J. ED - Pauschitz, A. ED - Vizintin, J. ED - Ciulli, E. ED - Crockett, R. T1 - Fuel economy of engine oils based on polyalkylene glycols N2 - The driver for automotive OEMs to work on alternative engine oils is the need for fuel economy and no adverse effect of the engine oil on the durability of particulate filters and catalysts. The alternative engine oils should for mid-term also comply with a positive environmental Profile. T2 - 3rd European Conference on Tribology and 4th Vienna International Conference on Nano-Technology CY - Vienna, Austria DA - 07.06.2011 KW - Biomotox KW - Head capacity KW - Fuel economy KW - Drain KW - Polyglycol KW - Polypropylene glycol KW - Polyalkylene glycol KW - Polybutylene glycol PY - 2011 SN - 978-3-901657-38-2 SP - 25 EP - 34 PB - MDH Media GesmbH CY - Wien AN - OPUS4-35671 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rohn, Holger T1 - The VDI guideline series 4800 resource efficiency: an approach for increasing resource efficiency with the aim of conservation of natural resources in the industrial sector N2 - In 2011, the German Association of Engineers (VDI) started working on a set of guidelines towards increased resource efficiency. These guidelines represent a framework that defines resource efficiency and outlines considerations for the producing industry. A special guideline for SMEs is included as well as guidelines on methodologies for evaluating resource use indicators, such as the cumulative raw material demand of products and production systems. Resource efficiency, defined here as the ratio of specific quantifiable use to natural resource consumption, can be evaluated by defining a function which expresses the specific use and quantifies the resource requirements through a set of indicators (use of raw materials, energy, water, land and ecosystem services including sinks). The results from this also depend on the system boundary parameters and the allocation rules for by-products and waste treatment options. Optimising resource use is possible at all stages of a product’s or production system’s life cycle chain (raw material extraction, production and manufacturing, use and consumption, and the end-of-life stage). VDI guidelines are widely accepted across Germany’s industrial sector and therefore represent an important means of mainstreaming resource efficiency in this target area. As well as providing a methodological framework, the guidelines describe strategies and measures towards increasing resource efficiency, and they enable industrial producers and service providers to identify potential areas of improvement. The full article presents an overview of the methodology and contents of these guidelines and discusses their impact in achieving absolute reductions in the industrial use of natural resources. T2 - World Resources Forum 2015 CY - Davos, Switzerland DA - 11.10.2015 KW - Resource Efficiency KW - Life cycle thinking KW - Products and production systems KW - Standardization PY - 2015 AN - OPUS4-35674 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hoffmann, Dirk A1 - Niesel, Konrad T1 - Effect of air pollutants on renderings and moisture-transport phenomena in masonry N2 - Determining a pore structure’s mechanical and chemical data on lime rendering exposed outdoors and including masonry in the laboratory, with regard to their behaviour on moisture transport and weathering was the objective. In search of clues for a dose-response relation - i.e. upon a connection between the emission rate of SO2 and NOx on one hand and the degree of damage to mainly plaster having a lime component on the other - it has been of interest to what extent their structural characteristics including pore space are modified and so consequently also physico-technical properties and chemical composition. For determining corresponding criteria, a widely diversified spectrum of test methods such as to obtain data concerning porosity and moisture transport, mechanical behaviour, and chemistry as well is available. A description of the manufacture of plate-shaped rendering specimens with lime putty, industrially hydrated lime and dolomitic hydrate (the last two also having a cement admixture) and also hydraulic lime as binding agents is included. First deposition velocity and absorption rate for SO2 were determined in laboratory tests on these materials in dry and moist states. After their exposure on outdoor racks at six locations in the Berlin region with differing SO2 atmospheric contents over at least 5 years, the samples of course show timedependent modifications of chemical and physical qualities which are especially reflected in the form of profiles of structure, strength and concentration, e.g. for sulphate. Local climatic differences, however, partly exert a greater influence on material than emissions. Similar investigations were performed on samples of comparable composition exposed 4 and 17 years. But the real surprise is furnished by the renderings’ behaviour depending upon orientation and upon height at a building. Since weathering behaviour and moisture transport (absorption, storage, release) are directly interdependent, further criteria are necessary for a critical assessment of a plasters’ pore structure. Starting from sands, plasters were characterized. The structural parameters were lastly influenced by the respective contents of sand, binder and mixing water. These results and those gained from bricks naturally find their expression in masonry sections manufactured there from, and above all in their capillary and evaporative behaviours, and also when applying different test liquids. Summary and cited literature is given at the end of this report. KW - Building Material KW - Mercury Intrusion Porosimetry KW - Gas Adsorption PY - 2008 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-356780 SP - 1 EP - 126 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-35678 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Simon, Franz-Georg A1 - Holm, Olaf T1 - Exergetic considerations on the recovery of metals from waste N2 - Bottom ash from municipal solid waste incineration (MSWI) consists of elemental metals in considerable amounts. The exergy of bottom ash was calculated to be some 100 kJ/mol, mainly as a result of the presence of elemental Fe and Al. From this it can be shown that the recovery of elemental metals Cu, Al and Fe is beneficial. The fine fraction <4 mm additionally contains chemically bound metals (oxides, carbonates, silicates). Separation prospects with techniques as in ore processing (flotation, density separation, bioleaching, hydrothermal solution) are discussed. Although the concentration of Cu compounds in bottom ash is in the range of today’s exploited ores the economic viability of the recovery of metal compounds is uncertain. For sufficient enrichment different concerted treatment steps are required. KW - bioleaching KW - bottom ash KW - cumulative energy consumption KW - cumulative exergy consumption KW - density separation KW - environmental technology KW - exergy KW - flotation KW - recycling technology KW - recovery KW - waste management PY - 2016 UR - http://www.inderscience.com/info/inarticletoc.php?jcode=ijex&year=2016&vol=19&issue=3 DO - https://doi.org/10.1504/IJEX.2016.075668 SN - 1742-8300 SN - 1742-8297 VL - 19 IS - 3 SP - 352 EP - 363 PB - Inderscience Enterprises Ltd. CY - Olney, UK AN - OPUS4-35646 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Elordui-Zapatarietxe, S. A1 - Fettig, Ina A1 - Richter, Janine A1 - Philipp, Rosemarie A1 - Vanermen, G. A1 - Monteyne, E. A1 - Boom, G. A1 - Emteborg, H. T1 - Preparation and evaluation of sufficiently homogeneous and stable reference materials for priority hazardous substances in whole water N2 - We have prepared and evaluated three whole water test materials containing eight polycyclic aromatic hydrocarbons (PAHs), six polybrominated diphenyl ethers (PBDEs) and tributyltin (TBT) with respect to homogeneity and short-term stability. The test materials were used as samples in two inter-laboratory comparisons. The materials were composed of natural mineral water and model suspended particulate matter (SPM) containing the target compounds at ng L-1 levels. The expanded uncertainty of the estimated mass concentrations in the final test materials was obtained by combining contributions from the homogeneity, the stability and the model SPM characterization. The whole water materials were sufficiently homogeneous and stable at 4 °C for their intended use. In total, 12 out of 15 investigated target parameters could be assessed to be present with a relative combined expanded uncertainty below 25 %. The outcome of the two interlaboratory comparisons confirmed the good quality of the test materials and the level of uncertainties associated with the estimated mass concentrations. These findings are an important contribution towards the development of whole water matrix reference materials certified for PAH, PBDE and TBT in support of the Water Framework Directive of the European Union. KW - Reference material KW - Referenzmaterial KW - Water Framework Directive KW - Wasserrahmenrichtlinie KW - Whole water sample KW - Gesamtwasserprobe PY - 2016 DO - https://doi.org/10.1007/s00769-015-1189-1 SN - 0949-1775 SN - 1432-0517 VL - 21 IS - 2 SP - 113 EP - 120 PB - Springer AN - OPUS4-35728 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Richter, Janine A1 - Elordui-Zapatarietxe, S. A1 - Emteborg, H. A1 - Fettig, Ina A1 - Cabillic, J. A1 - Alasonati, E. A1 - Gantois, F. A1 - Swart, C. A1 - Gokcen, T. A1 - Tunc, M. A1 - Binici, B. A1 - Rodriguez-Cea, A. A1 - Zuliani, T. A1 - Gonzalez Gago, A. A1 - Pröfrock, D. A1 - Nousiainen, M. A1 - Sawal, G. A1 - Buzoianu, M. A1 - Philipp, Rosemarie T1 - An interlaboratory comparison on whole water samples N2 - The European Water Framework Directive 2000/60/EC requires monitoring of organic priority pollutants in so-called whole water samples, i.e. in aqueous nonfiltered samples that contain natural colloidal and suspended particulate matter. Colloids and suspended particles in the liquid phase constitute a challenge for sample homogeneity and stability. Within the joint research project ENV08 ‘‘Traceable measurements for monitoring critical pollutants under the European Water Framework Directive 2000/60/EC’’, whole water test materials were developed by spiking defined amounts of aqueous slurries of ultrafinely milled contaminated soil or sediment and aqueous solutions of humic acid into a natural mineral water matrix. This paper presents the results of an European-wide interlaboratory comparison (ILC) using this type of test materials. Target analytes were tributyltin, polybrominated diphenyl ethers and polycyclic aromatic hydrocarbons in the ng/L concentration range. Results of the ILC indicate that the produced materials are sufficiently homogeneous and stable to serve as samples for, e.g. proficiency testing or method validation. To our knowledge, this is the first time that ready-to-use water materials with a defined amount of suspended particulate and colloidal matter have been applied as test samples in an interlaboratory exercise. These samples meet the requirements of the European Water Framework Directive. Previous proficiency testing schemes mainly employed filtered water samples fortified with a spike of the target analyte in a water-miscible organic solvent. KW - Water Framework Directive KW - Wasserrahmenrichtlinie KW - Interlaboratory comparison KW - Ringversuch KW - Whole water sample KW - Gesamtwasserprobe PY - 2016 DO - https://doi.org/10.1007/s00769-015-1190-8 SN - 0949-1775 SN - 1432-0517 VL - 21 IS - 2 SP - 121 EP - 129 PB - Springer AN - OPUS4-35730 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Cabillic, J. A1 - Fallot, C. A1 - Hein, Sebastian A1 - Lalere, B. A1 - Philipp, Rosemarie T1 - Développement et validation d’une méthode de référence pour l’analyse des HAP dans l’eau totale dans le contexte de la DCE T1 - Development and validation of a reference method for the analysis of PAHs in whole water in accordance to the WFD N2 - Afin de garantir la qualité des eaux en Europe, la Commission Européenne a demandé aux États Membres, de leur fournir des résultats de mesure comparables et traçables pour l’analyse des polluants critiques. Devant ces enjeux considérables pour la protection de l’environnement, l’apport de la métrologie est nécessaire pour améliorer la fiabilité des analyses et permettre la comparabilité des résultats. C’est pourquoi, le projet de recherche européen Euramet/EMRP/ENV08 « Traçabilité des mesures pour la surveillance des polluants critiques de la DCE, Directive Cadre européenne sur l’Eau (2000/60/CE) », financé par l’EMRP, avait pour objectif de fournir des éléments pour la mise en place d’une base métrologique. Des méthodes de référence primaires permettant d’analyser des substances dangereuses prioritaires y sont développées pour répondre aux exigences de la DCE en termes de niveaux de performance (limites de quantification et incertitudes). Les hydrocarbures aromatiques polycycliques (HAP), substances dangereuses prioritaires « orphelines » de méthodes DCE compatibles, font partie des polluants ciblés par le projet. Le développement et la validation de la méthode d’analyse des HAP dans l’eau totale ont été réalisés. La méthode qui satisfait au mieux les exigences de la DCE en termes de concentrations et d’incertitudes accessibles est l’extraction en phase solide (SPE) sur un support disque suivie d’une analyse par dilution isotopique associée à la chromatographie en phase gazeuse couplée à la spectroscopie de masse (DI-CG/SM). N2 - To ensure the water quality in Europe, the European Commission asked the member states to provide comparable and traceable measurement results for the analysis of critical pollutants. Considering the increasing environmental challenges, the contribution of metrology is necessary both for the improvement of analysis reliability and the comparability of results. For this reason the European research project Euramet/EMRP/ENV08 “Traceable measurements for monitoring critical pollutants under the European Water Framework Directive (WFD-2000/60/EC)”, funded by the EMRP, aimed to provide the elements for the development of a metrological basis. The project develops primary reference methods enabling the analysis of priority hazardous substances in order to meet the WFD requirements in terms of performance levels (limit of quantification and uncertainties). Polycyclic aromatic hydrocarbons (PAHs) – priority hazardous substances for which no DCE compatible methods exist – are among the three families of pollutants targeted by the project. This paper tackles the development and validation of the PAH analysis method on whole water samples. The method that best meets the requirements of the WFD in terms of level of concentration and uncertainty is the solid phase extraction (SPE) method with SPE-disks, followed by isotope dilution analysis combined with gas chromatography mass spectrometry (ID-GC/MS). KW - Reference method KW - Referenzmethode KW - Limit of quantification KW - Bestimmungsgrenze KW - Polycyclic aromatic hydrocarbons KW - Polyzyklische aromatische Kohlenwasserstoffe PY - 2015 UR - http://www.metrologie-francaise.fr/publications/revue_francaise_metrologie/2015-04/RFM40-1514.pdf DO - https://doi.org/10.1051/rfm/2015014 SN - 1772-1792 VL - 2015-4 IS - 40 SP - 3 EP - 12 AN - OPUS4-35731 LA - fra AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Neumann, Patrick P. A1 - Ebert, S. A1 - Lazik, D. A1 - Bartholmai, Matthias ED - Nicoletto, G. ED - Dan Pastrama, S. ED - Emri, I. T1 - Inverse calibration routine for linear soil gas sensors N2 - Gas sensors in linear form based on the measuring principle of gas selective permeability through a membrane were developed and introduced for the detection and quantification of gas concentrations. A current field study focuses on measuring CO2 concentrations for a spatially distributed monitoring of subsurface CO2 gas storage sites in near real time. A 400 m² test site and a corresponding laboratory system were built up to characterize, validate, and optimize the sensor. A calibration routine was developed, which can be applied subsequently to underground installation. First measurement results indicate the potential of the method. T2 - 32nd Danubia Adria Symposium on Advances in Experimental Mechanics CY - Starý Smokovec, Slovakia DA - 22.09.2015 KW - Linear sensor KW - Distributed sensor KW - Subsurface monitoring KW - Gas storage areas KW - Membrane-based gas sensing KW - Calibration PY - 2016 UR - http://www.sciencedirect.com/science/article/pii/S221478531600256X DO - https://doi.org/doi:10.1016/j.matpr.2016.03.051 SN - 2214-7853 VL - 3 IS - 4 SP - 1074 EP - 1078 PB - Elsevier Ltd. AN - OPUS4-35633 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Okkenhaug, G. A1 - Gebhardt, K.-A. G. A1 - Amstaetter, K. A1 - Bue, H. L. A1 - Herzel, Hannes A1 - Mariussen, E. A1 - Almås, Å. R. A1 - Cornelissen, G. A1 - Breedveld, G. D. A1 - Rasmussen, G. A1 - Mulder, J. T1 - Antimony (Sb) and lead (Pb) in contaminated shooting range soils: Sb and Pb mobility and immobilization by iron based sorbents, a field study N2 - Small-arm shooting ranges often receive a significant input of lead (Pb), copper (Cu) and antimony (Sb) from ammunition. The goal of the present study was to investigate the mobility, distribution and speciation of Pb and Sb pollution under field conditions in both untreated and sorbent-amended shooting range soil. Elevated Sb (19–349 μg L⁻¹) and Pb (7–1495 μg Pb L⁻¹) concentrations in the porewater of untreated soil over the four-year test period indicated a long-term Sb and Pb source to the adjacent environment in the absence of remedial measures. Mixing ferric oxyhydroxide powder (CFH-12) (2%) together with limestone (1%) into the soil resulted in an average decrease of Sb and Pb porewater concentrations of 66% and 97%, respectively. A similar reduction was achieved by adding 2% zerovalent iron (Fe°) to the soil. The remediation effect was stable over the four-year experimental period indicating no remobilization. Water- and 1 M NH₄NO₃-extractable levels of Sb and Pb in field soil samples indicated significant immobilization by both treatments (89–90% for Sb and 89–99% for Pb). Results from sequential extraction analysis indicate fixation of Sb and Pb in less accessible fractions like amorphous iron oxides or even more crystalline and residual mineral phases, respectively. This work shows that amendment with Fe-based sorbents can be an effective method to reduce the mobility of metals both in cationic and anionic form in polluted shooting range soil. KW - Shooting range soil KW - Antimony KW - Lead KW - Soil amendment KW - Porewater KW - Field test PY - 2016 DO - https://doi.org/10.1016/j.jhazmat.2016.01.005 SN - 0304-3894 VL - 307 SP - 336 EP - 343 PB - Elsevier Science CY - Amsterdam, Netherlands AN - OPUS4-36109 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Muhammad, R. T1 - Influence of the of dealumination and porosity on the acid sites of natural zeolite clinoptilolite N2 - Heavy feedstock from crude and bio oil is a widely available and renewable resource for production of fuel and starting materials for other organic valuables by cracking or hydrocracking. Catalytic processing of heavy feedstock can meet the increased demand of energy up to a great extent. It requires the application of acidic catalysts like zeolites. However, the used synthetic catalysts are difficult to recover and reuse and are mostly spent. The use of natural zeolite as spent catalysts may open new perspectives in the chemical use of heavy feed feedstock by chemical conversion. Natural zeolites are not expensive, widely available and environment friendly. Clinoptilolite is the most abundant natural zeolite. Clinoptilolite has a crystalline structure with a defined micropore system of medium size showing unique ion exchange and sorption properties. However, it is catalytically active only in the H-form. Also certain porosity is required for improvement of the accessibility of active sites. This paper deals with the tuning of acid properties and of the mesoporosity of the clinoptilolite by variation of the Si/Al framework ratio, extra-framework aluminum and modification of the porosity by specific acid and water vapor treatment. The preparation of hierarchical pore structures containing interconnected micro-meso-macropores is an important factor influencing the catalytic performance. The obtained materials have been characterized by XRD, TEM, FTIR, Raman, TG/DSC. The chemical composition has been determined by ICP-AES. The porosity have been investigated by nitrogen adsorption desorption measurements. The acidity has been measured by Ammonia-TPD. The extent of dealumination, stability of the clinoptilolite against acid treatment and the change in the nature of acid sites and their local structure has been studied by solid state 29Si and 27Al MAS NMR spectroscopy in detail. The catalytic activity has been investigated in the acetalization of benzaldehyde with 1,3-butanediol. The impact of the porosity, change of the Si/Al ratio as well as present Al species on catalytic properties will be discussed. T2 - 28. Deutsche Zeolith-Tagung CY - Giessen, Germany DA - 02.03.2016 KW - NMR KW - Zeolite KW - Clinoptilolite KW - Catalyst PY - 2016 AN - OPUS4-35886 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - August, Hans A1 - Tatzky, Renate A1 - Pastuska, Gerhard A1 - Win, Tin T1 - Untersuchung des Permeationsverhaltens von handelsüblichen Kunststoffdichtungsbahnen als Deponiebasisabdichtung gegenüber Sickerwasser, organischen Lösungsmitteln und deren wäßrige Lösungen N2 - Zur Basisabdichtung von Mülldeponien werden zunehmend polymere Abdichtungen mit Foliendecken zwischen 1 und 3 mm eingesetzt, die vielfach als absolut dicht gegenüber Sickerwässer und deren Inhaltsstoffen gelten. Durch Permeationsvorgänge ist jedoch mit Restdurchlässigkeiten zu rechnen, die auch bei technisch einwandfreien, intakten Folien auftreten. Es werden Meßmethoden vorgestellt, derartige Restdurchlässigkeitsraten an handelsüblichen Dichtungsbahnen für Deponiebasisabdichtungen zu messen. Als Permeenten dienen neben Sickerwasser aus einer Hausmülldeponie, konzentrierte, reine organische Lösungsmittel, deren Gemische untereinander und stark verdünnte Lösungen organischer Lösungsmittel in Wasser. Meßergebnisse werden angegeben und diskutiert. KW - Müll KW - Abfall KW - Ablagerung KW - Deponie KW - Sickerwasser KW - Grundwasserschutz KW - Umweltschutz KW - Polymere Deponiebasisabdichtungen KW - organische Lösungsmittel KW - Permeation KW - Experimentelle Ergebnisse PY - 1984 SP - 1 EP - 108 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-35914 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Madkour, Sherif A1 - Melnichu, I. A1 - Choukourov, A. A1 - Krakovsky, I. A1 - Biedermann, H. A1 - Schönhals, Andreas T1 - In situ nanocalorimetric investigations of plasma assisted deposited poly(ethylene oxide)-like films by specific heat spectroscopy N2 - In the recent years, highly crosslinked plasma polymers have started to unveil their potential in numerous biomedical applications in thin-films form. However, conventional diagnostic methods often fail due to their diverse molecular dynamics conformations. Here, glassy dynamics and the melting transition of thin PEO-like plasma assisted deposited (ppPEO) films (thickness 100 nm) were In situ studied by a combination of specific heat spectroscopy, utilizing pJ/K sensitive AC-calorimeter chip, and composition analytical techniques. Different crosslinking densities were obtained by different plasma powers during the deposition of the films. Glassy dynamics was observed for all values of the plasma power. It was found that the glassy dynamics slows down with increasing the plasma power. Moreover, the underlying relaxation time spectra broaden indicating that the molecular motions become more heterogeneous with increasing plasma power. In a second set of experiment, the melting behavior of the ppPEO films was studied. The melting temperature of ppPEO was found to be decreasing with increasing plasma power. This was explained by a decrease of the order in the crystals due to formation of chemical defects during the plasma process. KW - Plasma deposited polymers KW - Nanocalorimetry KW - Thin polymer films KW - Glass transition PY - 2016 DO - https://doi.org/10.1021/acs.jpcb.6b01355 SN - 1520-6106 SN - 1520-5207 VL - 120 IS - 16 SP - 3954 EP - 3962 PB - American Chemical Society CY - Washington, DC, USA AN - OPUS4-35922 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Münchow, Paul T1 - Entwicklung eines spektralanalytischen Multielementverfahrens zur schnellen sequentiellen Bestimmung umweltrelevanter Metalle in Abwässern N2 - Mit der Plasmaspektrometrie (ICP) wurden in Abwässern aus dem Berliner Abwassersystem simultan 11 Elemente (Al, B, Ba, Cr, Cu, Fe, Mn, Ni, P, Ti, Zn) bestimmt. Der erforderliche Arbeitsaufwand ist erheblich geringer als nach Deutschen Einheitsverfahren zur Abwasseruntersuchung. Bestimmungsgrenzen werden mitgeteilt, auf systematische Fehlermöglichkeiten wird eingegangen. Durch Eindampfen der Proben lassen sich die Nachweisgrenzen in den meisten Fällen um den Faktor 10 weiter senken. Die Hydridtechnik zur Verbesserung der Nachweisempfindlichkeit bei den Elementen Sn, As, Sb, Se erwies sich in der Abwassermatrix als problematisch. KW - Abwasser KW - chemische Analyse KW - Schwermetalle KW - ICP PY - 1984 IS - UBA-FB 84-082 SP - 1 EP - 83 AN - OPUS4-35913 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wallau, Wilma A1 - Schlawitschek, C. A1 - Arellano-Garcia, H. T1 - Electric field driven separation of oil-water mixtures: Model development and experimental verification N2 - Electrocoalescence of aqueous droplets in oil emulsions is commonly contemplated for enhancing separation. High voltage electric fields can induce charges to Drops evoking merging of adjacent droplets. The newly formed larger Drops then sink faster in gravitational common settlers. Therefore, separation performance of an electrostatic coalescer is strictly linked to characteristics of the electric field and properties of the liquid−liquid system. In this work, the coalescence Performance of water droplets sinking in dodecane at a pulsed DC electric field is investigated. An experimental setup allowing the simultaneous injection of similar sized drops, setting of voltage and pulsation frequency, and particle tracking at high frame rate and resolution is designed. The generated data are used to check the validity of modeling approaches for drag, dipole−dipole forces, and film-thinning. Furthermore, CFD simulations are carried out using a volume of fluid method tracking the interfaces between the two phases. KW - Drop-drop coalescence KW - Electrocoalescence KW - Water-in-oil PY - 2016 DO - https://doi.org/10.1021/acs.iecr.5b03876 SN - 0888-5885 SN - 1520-5045 VL - 55 IS - 16 SP - 4585 EP - 4598 AN - OPUS4-36273 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schoknecht, Ute T1 - Ausgewählte Ergebnisse aus einem UBA-Vorhaben zur Auswaschung von Bioziden aus behandelten Materialien N2 - Die Auswaschung von Bioziden wurde für eine Reihe von behandelten Materialien in Labor- und Freilandversuchen untersucht. Beobachtungen aus Freilanduntersuchungen und Ergebnisse aus Regressionsanalysen zum Einfluss von Witterungsfaktoren werden dargestellt. Verschiedene Untersuchungen zu Materialeigenschaften, die Einfluss auf die Auswaschbarkeit von Bioziden haben können, werden für zwei Farben verglichen. Ein Modellansatz zur Beschreibung von Laborversuchsdaten wird kurz erläutert. T2 - Umwelteigenschaften mineralischer Werkmörtel und pastöser Produkte CY - Holzkirchen, Germany DA - 31.05.2016 KW - Biozide KW - Leaching KW - Materialien PY - 2016 AN - OPUS4-36324 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. T1 - Anwendungsbeispiele für den Einsatz von Drohnen - Lokalisierung von Gasemissionsquellen, Erstellung von Gasverteilungskarten und Bekämpfung des Eichenprozessionsspinners N2 - Der Vortrag gibt Beispiele dafür, wie Drohnen sinnvoll im zivilen Bereich eingesetzt werden können. Insbesondere werden die Lokalisierung von Gasemissionsquellen, die Erstellung von Gasverteilungskarten und die Bekämpfung des Eichenprozessionsspinners näher vorgestellt. T2 - DRONEMASTERS.Berlin MeetUp #01.16 CY - Berlin, Germany DA - 27.01.2016 KW - Lokalisierung von Gasemissionsquellen KW - Erstellung von Gasverteilungskarten KW - Eichenprozessionsspinner PY - 2016 AN - OPUS4-36225 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Neumann, Patrick P. A1 - Lazik, D. A1 - Bartholmai, Matthias T1 - Tomographic reconstruction of soil gas distribution from multiple gas sources based on sparse sampling N2 - A monitoring method is introduced that creates twodimensional (2D) maps of the soil gas distribution. The method combines linear gas sensing technology for in-situ monitoring of gases in soil with the mapping capabilities of Computed Tomography (CT) to reconstruct spatial and temporal resolved gas distribution maps. A weighted iterative algebraic reconstruction method based on Maximum Likelihood with Expectation Maximization (MLEM) in combination with a source-by-source reconstruction approach is introduced that works with a sparse setup of orthogonally-aligned linear gas sensors. The reconstruction method successfully reduces artifact production, especially when multiple gas sources are present, allowing the discrimination between true and non-existing so-called ghost source locations. Experimental validation by controlled field experiments indicates the high potential of the proposed method for rapid gas leak localization and quantification with respect to Pipeline or underground gas storage issues. KW - Computed tomography KW - Gas distribution mapping and gas source localization KW - Discrimination of multiple gas sources KW - Distributed linear sensor KW - Membrane-based gas sensing KW - Subsurface monitoring KW - Gas storage areas PY - 2016 DO - https://doi.org/10.1109/JSEN.2016.2545103 SN - 1530-437X VL - 16 IS - 11 SP - 4501 EP - 4508 PB - IEEE - Inst. Electrical Electronics Engineers Inc CY - Hoes Lane, NJ, USA AN - OPUS4-36228 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sproesser, Gunther A1 - Chang, Ya-Ju A1 - Pittner, Andreas A1 - Rethmeier, Michael A1 - Finkbeiner, Matthias T1 - Laser-MSG-Hybridschweißen und die Ökobilanz: Sieg nach Punkten N2 - Es ist ein Naturgesetz: Mit der verarbeiteten Blechdicke steigt der Zeit-, Material- und Energiebedarf beim Fügen überproportional. Aber ist das noch umweltverträglich ? Dieser Frage stellte sich Gunther Sproesser mit seinen Kollegen an der Technischen Universität Berlin. KW - MSG-Schweißen KW - Hochleistungsschweißen KW - Ökobilanz KW - Laser-MSG-Hybridschweißen PY - 2015 UR - http://www.laser-community.com/de/schweiss-verfahren-im-oeko-check/ N1 - In Deutsch und Englisch erschienen. Titel in English: "A win on points: LAHW/GMAW welding tops life-cycle analysis study" IS - 21/November 2015 SP - 6 EP - 6 AN - OPUS4-35438 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Arroyo-Abad, Uriel A1 - Pfeifer, M. A1 - Mothes, S. A1 - Stärk, H.-J. A1 - Mattusch, J. A1 - Reemtsma, T. A1 - Piechotta, Christian T1 - Determination of moderately polar arsenolipids and mercury speciation in freshwater fish of the River Elbe (Saxony, Germany) N2 - Arsenic and mercury are frequent contaminants in the environment and care must be taken to limit their entrance into the food chain. The toxicity of both elements strongly depends upon their speciation. Total amounts of As and Hg as well as their species were analyzed in muscle and liver of 26 fishes of seven freshwater fish species caught in the River Elbe. The median concentrations of As were 162 mg kg-1 w.w. in liver and 92 mg kg-1 w.w. in muscle. The median concentrations of total Hg were 241 mg kg-1 w.w. in liver and 256 mg kg-1 w.w. in muscle. While this level of Hg contamination of the freshwater fish in the River Elbe is significantly lower than 20 years ago, it exceeds the recommended environmental Quality standard of 20 mg Hg kg-1 w.w. by a factor of 5e50. However, the European maximum level of 500 mg Hg kg-1 for fish for human consumption is rarely exceeded. Arsenic-containing fatty acids and hydrocarbons were determined and partially identified in methanolic extracts of the fish by HPLC coupled in parallel to ICP-MS (element specific detection) and ESI-Q-TOF-MS (molecular structure detection). While arsenobetaine was the dominant As species in the fish, six arsenolipids were detected and identified in the extracts of liver tissue in common bream (Abramis brama), die (Leuciscus idus), asp (Aspius aspius) and northern pike (Esox lucius). Four arsenic-containing fatty acids (AsFA) and two arsenic-containing hydrocarbons (AsHC) are reported in freshwater fish for the first time. With respect to mercury the more toxic MeHgþ was the Major species in muscle tissue (>90% of total Hg) while in liver Hg2þ and MeHgþ were of equal importance. The results Show the high relevance of element speciation in addition to the determination of total element concentrations to correctly assess the burden of these two elements in fish. KW - Element species KW - Freshwater fish KW - Metal contamination KW - Arsenolipids PY - 2016 DO - https://doi.org/10.1016/j.envpol.2015.10.015 SN - 0269-7491 VL - 208 SP - Part B, 458 EP - 466 PB - Elsevier Ltd. AN - OPUS4-35399 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Arroyo-Abad, Uriel A1 - Hu, Z. A1 - Findeisen, M. A1 - Pfeifer, Dietmar A1 - Mattusch, J. A1 - Reemtsma, T. A1 - Piechotta, Christian T1 - Synthesis of two new arsenolipids and their identification in fish N2 - Arsenolipids (AsL) of the type arsenic-containing fatty acids (AsFA) and hydrocarbons (AsHC) are natural organoarsenic compounds present in high abundance in seafood. Since little is known about their toxicity, there is a significant concern about their health risk. Here we report the synthesis of two new AsL and their identification in fish by liquid chromatography (LC) coupled simultaneously to inductively coupled plasma mass spectrometry (ICP-MS) and to high resolution mass spectrometry (HR-MS). The molecular structure was elucidated on the basis of their exact mass and their product ion mass spectra. One of the synthesized AsL has been already identified in fish samples, meanwhile, the other arsenolipid is reported here as a natural product in fish. KW - Arsenolipids KW - ESI-MS/MS KW - HPLC-ICP-MS/HR-MS KW - Synthesis PY - 2016 DO - https://doi.org/10.1002/ejlt.201400502 SN - 1438-9312 VL - 118 IS - 3 SP - 445 EP - 452 PB - WILEY-VCH Verlag GmbH & Co CY - Weinheim AN - OPUS4-35400 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schoknecht, Ute A1 - Mathies, Helena A1 - Wegner, R. T1 - Biocide leaching during field experiments on treated articles N2 - Background: Biocidal products can be sources of active substances in surface waters caused by weathering of treated articles. Marketing and use of biocidal products can be limited according to the European Biocidal Products Regulation if unacceptable risks to the environment are expected. Leaching of active substances from treated articles was observed in field experiments to obtain information on leaching processes and investigate the suitability of a proposed test method. Results: Leaching under weathering conditions proceeds discontinuously and tends to decrease with duration of exposure. It mainly depends on the availability of water, but is also controlled by transport processes within the materials and stability of the observed substances. Runoff amount proved to be a suitable basis to compare results from different experiments. Concentrations of substances are higher in runoff collected from vertical surfaces compared to horizontal ones, whereas the leached amounts per surface area are higher from horizontal surfaces. Gaps in mass balances indicate that additional processes such as degradation and evaporation may be relevant to the fate of active substances in treated articles. Leached amounts of substances were considerably higher when the materials were exposed to intermittent water contact under laboratory conditions as compared to weathering of vertically exposed surfaces. Conclusions: Experiences from the field experiments were used to define parameters of a procedure that is now provided to fulfil requirements of the Biocidal Products Regulation. The experiments confirmed that the amount of water which is in contact with exposed surfaces is the crucial parameter determining leaching of substances. KW - Biozidprodukte KW - Farben KW - Textil KW - Auswaschung KW - Freilandtest KW - Biocidal products KW - Paints KW - Textile KW - Leaching KW - Field test PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-354090 DO - https://doi.org/10.1186/s12302-016-0074-9 VL - 28 IS - 6 SP - 1 EP - 10 PB - Springer CY - SpringerOpen AN - OPUS4-35409 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bachmann, H. J. A1 - Bucheli, T. D. A1 - Dieguez-Alonso, A. A1 - Fabbri, D. A1 - Knicker, H. A1 - Schmidt, H.-P. A1 - Ulbricht, A. A1 - Becker, Roland A1 - Buscaroli, A. A1 - Buerge, D. A1 - Cross, A. A1 - Dickinson, D. A1 - Enders, A. A1 - Esteves, V.I. A1 - Evangelou, M. W. H. A1 - Fellet, G. A1 - Friedrich, K. A1 - Gasco Guerrero, G. A1 - Glaser, B. A1 - Hanke, U. M. A1 - Hanley, K. A1 - Hilber, I. A1 - Kalderis, D. A1 - Leifeld, J. A1 - Masek, O. A1 - Mumme, J. A1 - Paneque Carmona, M. A1 - Calvelo Pereira, R. A1 - Rees, F. A1 - Rombola, A. G. A1 - de la Rosa, J. M. A1 - Sakrabani, R. A1 - Sohi, S. A1 - Soja, G. A1 - Valagussa, M. A1 - Verheijen, F. A1 - Zehetner, F. T1 - Towards the standardization of biochar analysis: the COST action TD1107 interlaboratory comparison N2 - Biochar produced by pyrolysis of organic residues is increasingly used for soil amendment and many other applications. However, analytical methods for its physical and chemical characterization are yet far from being specifically adapted, optimized, and standardized. Therefore, COST Action TD1107 conducted an interlaboratory comparison in which 22 laboratories from 12 countries analyzed three different types of biochar for 38 physical–chemical parameters (macro- and microelements, heavy metals, polycyclic aromatic hydrocarbons, pH, electrical conductivity, and specific surface area) with their preferential methods. The data were evaluated in detail using professional interlaboratory testing software. Whereas intralaboratory repeatability was generally good or at least acceptable, interlaboratory reproducibility was mostly not (20% < mean reproducibility standard deviation < 460%). This paper contributes to better comparability of biochar data published already and provides recommendations to improve and harmonize specific methods for biochar analysis in the future. KW - Biochar KW - Analysis KW - Standardization KW - Ring test KW - Interlaboratory comparison PY - 2016 DO - https://doi.org/10.1021/acs.jafc.5b05055 SN - 0021-8561 SN - 1520-5118 VL - 64 IS - 2 SP - 513 EP - 527 PB - American Chemical Society CY - Columbus, Ohio AN - OPUS4-35289 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hornemann, A. A1 - Eichert, D. A1 - Flemig, Sabine A1 - Ulm, G. A1 - Beckhoff, B. T1 - Qualifying label components for effective biosensing using advanced high-throughput SEIRA methodology N2 - The need for technological progress in bio-diagnostic assays of high complexity requires both fundamental research and constructing efforts on nano-scaled assay recognition elements that can provide unique selectivity and design-enhanced sensitivity features. Nanoparticle induced sensitivity enhancement and its application related to multiplexed capability Surface-Enhanced InfraRed Absorption (SEIRA) assay formats are well suitable for these purposes. The potential of diverse fluorophore–antibody conjugates, being chemisorbed onto low-cost gold nanoparticulate SEIRA substrates, has been explored with respect to their spectral discriminability. These novel biolabels deliver molecular SEIRA fingerprints that have been successfully analyzed by both uni- and multivariate analyzing tools, to discriminate their multiplexing capabilities. We show that this robust spectral encoding via SEIRA fingerprints opens up new opportunities for a fast, reliable and multiplexed high-end screening in biodiagnostics. KW - SEIRA methodology KW - bio-diagnostic KW - nanotechnology PY - 2015 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-351389 DO - https://doi.org/10.1039/C4CP05944A SN - 1463-9076 SN - 1463-9084 VL - 17 IS - 14 SP - 9471 EP - 9479 PB - The Royal Soc. of Chemistry CY - Cambridge AN - OPUS4-35138 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ostermann, Markus A1 - Herzel, Hannes A1 - Kühn, A. A1 - Mory, D. A1 - Wedell, R. T1 - Prozessanalytik mit Online-RFA und Online-LIBS für die Regelung der Aufarbeitung von Klärschlammaschen T1 - Online Process Analytics with XRF and LIBS for the Control of the Recycling of Sewage Sludge Ashes N2 - Es wurde ein Online-Analysenverfahren zur Bestimmung von Elementgehalten in Klär-schlammaschen und deren Produkten aus einem thermochemischen Verfahren entwickelt. Durch das thermochemische Verfahren können Wertstoffe aus den Aschen wieder für die Kreislaufwirtschaft nutzbar gemacht und Schadstoffe sicher entfernt werden. Das Analysensystem ist eine Methodenkombination von Online-Laser induzierter Plasma Spektroskopie (LIBS) und Online-Röntgenfluoreszenzanalyse (RFA). Robustheit und modulare Bauweise des Verfahrens sind wichtige Anforderungen um auch für andere Anwendungen nutzbar zu sein. N2 - An online analysis method has been developed for the determination of element mass fractions in sewage sludge ashes and their products originating from a thermochemical process. Within this process resources from the sewage sludge ashes can be re-utilized for the recycling economy and pollutants can be removed. The applied analysis system is a method combination of Online-laser induced breakdown spectroscopy (LIBS) and online- X-ray fluorescence (XRF). Robustness and a modular construction are important demands for successful future applications. KW - Klärschlammasche KW - Phosphor KW - Prozessanalytik KW - Röntgenfluoreszenzanalyse KW - LIBS PY - 2016 DO - https://doi.org/10.1002/cite.201500186 SN - 1522-2640 VL - 88 IS - 6 SP - 786 EP - 792 PB - Wiley-VCH Verlag GmbH & Co. KGaA CY - Weinheim, Germany AN - OPUS4-36334 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger T1 - Natural and cultural history of clothes moths including their biological control N2 - Natural and cultural history of clothes moths including their control with paraitoid wasps T2 - Kolloquium CY - Berlin, Germany DA - 09.05.2016 KW - Clothes moth KW - Natuarl history KW - Pest control PY - 2016 AN - OPUS4-36350 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Goedecke, Caroline T1 - Heterogeneous photocatalysis - a promising method for the removal of environmental contaminants from water N2 - In recent years advanced oxidation processes have become an important part of research due to their capacity to degrade many environmental pollutants during water treatment. Especially the heterogeneous photocatalysis is a promising method because it often results in a full mineralization of many hazardous organic compounds. However incomplete degradation reactions during this process can result in transformation products due to the oxidative conditions. The transformation products may have a higher toxicity than the precursor substances and are often only partly removed during the waste water treatment. Since a lot of these compounds are still unknown, the transformation products are not detected by target analysis used in sewage treatment plants and are often released into the aquatic ecosystems. Therefore, extensive and effective non-target analytical methods are necessary for the monitoring and identification of the transformation products which can be generated during waste water treatment. Among various semiconductors, titanium dioxide (TiO2) is the most frequently used photocatalyst because of its inexpensiveness, non-toxicity, chemical stability and its high photocatalytic activity. If TiO2 is irradiated with light of an energy higher than the band gap of the semiconductor, electron-hole pairs are generated on the surface of the TiO2, resulting in the formation of active oxidized species such as hydroxyl radicals which can react with environmental pollutants. To study photocatalytic reactions, a model system has been developed to simulate environmental relevant conditions for photocatalytic reactions of organic substances on a laboratory scale. The commonly used pharmaceuticals metformin and gabapentin were selected as model substances because of their high input in waste water and the little information about their occurrence, behavior and fate in the environment. Metformin is the drug of choice for treating type 2 diabetes. The drug therapy for diabetes mellitus has increased significantly in recent years. More than half of the total amount of pharmaceuticals in the environment are the antidiabetic agent metformin and its major transformation product guanylurea. Gabapentin is an analogon of the neurotransmitter γ-aminobutyric acid (GABA) which is used as antiepileptic drug and for the treatment of neuropathic pain. Gabapentin is found in waste water influent in the high ng/L range. First results of the optimization of the photocatalyst and its application are shown. T2 - NonTarget 2016 CY - Ascona, Switzerland DA - 29.05.2016 KW - photocatalysis KW - transformation KW - non target analysis PY - 2016 AN - OPUS4-36381 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mülow-Stollin, Ulrike T1 - Extensive study of the fate of triazole fungicides using model systems N2 - In order to provide nutrition for a growing world population pesticides are a necessary tool. Crop protection agents may be considered safe, if handled correctly. Nevertheless, they are subject to transformation processes and metabolisation in the environment and technical installations. Transformation products (TP) and metabolites may exhibit properties other than those of the mother substance. They can be more harmful and thereby pose a threat to environmental and human health. With 19 % market share in 2014, triazole pesticides are the class of organic fungicides which are most commonly used in Germany.1 However, only little data is available concerning their TP and metabolites. During this study the fate of the triazole fungicides propiconazole and difenoconazole in soil and water using model reaction systems mimicking their pathway in the environment and the industrial water treatment is investigated. During application the substances may directly contaminate soil as well as surface waters. Both pesticides are considered persistent in soil and very stable towards aqueous photolysis.2 In this case however, the role of natural organic matter has not yet been examined. Since both pesticides also show moderate mobility in soils they may end up in ground water from which drinking water is produced. During this process, waters are treated with chlorine agents, ozone, and energy-rich UV radiation. Owing to the vigorous conditions the formation of a variety of technical TP can be expected. Additionally, for all environmental compartments the degradation of the fungicides by bacteria is a factor which needs to be taken into account. For this survey, iron-oxidising bacteria of the leptothrix variety were chosen as model organisms. Their potential for the metabolisation of the analytes is investigated. In this work degradation and transformation of the fungicides is monitored using quantitative target analysis. Major components in the reaction mixtures are identified by non-target analysis. GC-EI-MS-spectra, HR-MS-measurements, or the comparison with native standards are utilised for structural elucidation. For identification, products will be isolated and characterised by NMR. Toxicity assessment of these TP is essential to define threshold values in the environment. The model reaction system considering the interaction with organic matter will be presented and possible TP will be shown. T2 - NonTarget 2016 CY - Ascona, Switzerland DA - 29.05.2016 KW - pesticides KW - fungicides KW - non-target KW - environment PY - 2016 AN - OPUS4-36384 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald T1 - Measurement of particle emission during brake dynamometer tests N2 - Aerosol emissions from brake pads are evolving into the focus of industrie and regulation. Many institutes are extending their dynamometer test stands with aerosol measurement equipement. While this is in general a good developement, the details of aerosol measurement and the special problems in the case of brake pad emissions need some special attention. The instrumentation can not be used out of the box and the important parameters will be highlighted in this presentation. T2 - Role of Third Bodies in Tribology CY - Berlin, Germany DA - 09.06.2016 KW - brake KW - Bremsen KW - nano KW - nanoparticle KW - tribology KW - Tribologie KW - ultrafine KW - dust KW - Staub KW - Nanopartikel KW - Nano PY - 2016 AN - OPUS4-36453 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Oliver T1 - Phosphorrückgewinnung - ein wichtiger Beitrag zur Kreislaufwirtschaft N2 - Phosphor ist ein für alle Lebewesen essentielles Element und in seinen Funktionen nicht zu ersetzen. Der Bedarf wird aus der Nahrung gedeckt, daher wird Phosphor letztendlich durch Ackerbau den Böden entzogen. Der Nährstoff muss ersetzt werden, um dauerhafte Landwirtschaft zu ermöglichen. Das geschieht zum einen durch den Einsatz von Wirtschaftsdüngern, aber zu einem großen Teil auch durch Mineraldünger. Das hierfür benötigte Rohphosphat wird bergmännisch aus fossilen Lagerstätten gewonnen. Die entsprechende Reichweite wird auf über 300 Jahre geschätzt. Daher besteht zwar keine unmittelbare Gefahr, dass dieser lebenswichtige Nährstoff zu Neige geht, es bestehen jedoch erhebliche Versorgungsrisiken. Zum einen ist Europa nahezu vollständig von Importen abhängig und damit auch Schwankungen der Weltmarktpreise ausgesetzt. Darüber hinaus liegen Förderung und Reserven von Rohphosphaten entweder in Ländern mit hohem Eigenbedarf (USA, China) oder in politisch instabilen Regionen (Marokko, West Sahara). Außerdem sind viele Rohphosphate mit Schwermetallen wie Uran, Thorium und Cadmium belastet. Das Umweltbundesamt schätzt, dass jährlich mehr als 160 t Uran durch Mineraldünger auf deutsche Ackerflächen ausgebracht werden. Rückgewinnung von Phosphor könnte helfen, diese Probleme zu reduzieren. Ein bedeutendes Potential dafür stellt der Abwasserstrom dar. Die Menge an Phosphor darin wird deutschlandweit auf etwa 70.000 t jährlich geschätzt. Das entspricht etwa der Hälfte der Menge an Phosphor, die derzeit für Mineraldünger benötigt wird. Der Vortrag würde sich mit möglichen Prozessen der Rückgewinnung, deren Wirtschaftlichkeit und Herausforderungen der Analytik befassen: - in den letzten Jahren wurden zahlreiche Verfahren zur Rückgewinnung von Phosphor aus verschiedensten Phasen der Abwasserreinigung entwickelt (wässrige Phase, Klärschlamm, Klärschlammasche). Ausgewählte Verfahren würden vorgestellt und bewertet. - für einen Einsatz der so gewonnenen Recyclingphosphate als Düngemittel muss die Schadstofffreiheit und Pflanzenverfügbarkeit der Nährstoffe sichergestellt werden. Dazu ist zu prüfen, ob die zurzeit gängigen Verfahren der Probenvorbereitung und Analytik auch auf Recyclingphosphate anwendbar sind. Das gilt neben der Bioverfügbarkeit von Phosphor besonders für Schadstoffe, da die Recyclingdünger aus Abfallmaterialien gewonnen werden, die stark belastet sein können. Das gilt besonders für die speziesspezifische Analytik von Chrom (Chrom (VI) vs. Chrom (III)) in verschiedenen Matrices. T2 - Beiratssitzung Themenfeld Umwelt CY - BAM, Berlin, Germany DA - 10.06.2016 KW - Phosphor KW - Rückgewinnung KW - Umweltanalytik KW - Ressourcenschonung PY - 2016 AN - OPUS4-36451 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleis, M. A1 - Simon, Franz-Georg ED - Thomé-Kozmiensky, Karl J. T1 - Novellierung des BVT-Merkblattes Abfallverbrennung – Sachstand, Entwicklungstendenzen und neue Verfahren zur Aufbereitung von Rostaschen und Filterstäuben – N2 - Die europäischen BVT-Merkblätter beschreiben die besten verfügbaren Techniken zum emissionsarmen Betrieb von industriellen Produktionsprozessen, von technischen Verfahren zur Gewinnung und Verarbeitung von Rohstoffen, von Anlagen zur Erzeugung von Strom und Wärme und zur Behandlung und Verwertung von Abfällen und anderen technischen Prozessen. Die Abfallwirtschaft ist bei den Arbeiten zur Revision der BVT-Merkblätter gleich mit zwei Aktivitäten beteiligt, da sich aktuell sowohl das BVT-Merkblatt Abfallbehandlung als auch das BVT-Merkblatt Abfallverbrennung in der Revision befinden. Das Umweltbundesamt hat die Aufgabe, die Überarbeitung der BVT-Merkblätter national zu koordinieren und an den Arbeiten in Sevilla im EIPPC Büro und bei der Europäischen Kommission fachlich mitzuwirken. Der Beitrag beschreibt die aktuellen Aktivitäten zur Revision des BVT-Merkblattes Abfallverbrennung und Stand des Überarbeitungsprozesses auf europäischer Ebene mit dem inhaltlichen Schwerpunkt bei den zu erwartenden Anforderungen an die Entsorgung von Aschen und Schlacken aus der Abfallverbrennung mit einem Schwerpunkt bei den Siedlungsabfallverbrennungsanlagen. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 20.06.2016 KW - Rostasche KW - Abfallverbrennung KW - Aufbereitung PY - 2016 UR - http://www.vivis.de/phocadownload/2016_mna/2016_MNA_163-172_Gleis.pdf SN - 978-3-944310-28-2 VL - 3 SP - 163 EP - 172 PB - TK Verlag Karl Thomé-Kozmiensky CY - Nietwerder AN - OPUS4-36622 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -