TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 52, Heft 2 T3 - Amts- und Mitteilungsblatt der BAM - 2/2022 KW - Festlegungen KW - Zulassungen KW - Richtlinien KW - Anerkennungen PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-550917 SN - 0340-7551 VL - 52 IS - 2 SP - 55 EP - 158 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-55091 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Babutzka, Martin A1 - et al., T1 - Exposure Site Catalogue - Catalogue of atmospheric corrosion field exposure sites in Europe N2 - Exposure sites and outdoor exposure have always been a part of atmospheric corrosion research providing the “final answer”, although at the cost of long exposure times. Individual exposure programs such as ISOCORRAG, MICAT and ICP Materials have resulted in collaborative networks of exposure sites. So far, however, there has been no collective effort to put together currently active sites in a comprehensive manner and across programs and nations. The information collected in the catalogue is possible thanks to the work of all individual site managers listed as contact persons, efforts of members of Working Party 25 (WP25) Atmospheric Corrosion of the European Federation of Corrosion (EFC) and financial support of the EFC. With this Catalogue you can both get a general overview of what is available and be guided if you are looking for a particular environment with certain characteristics. KW - Atmospheric Corrosion KW - Atmosphärische Korrosion KW - Corrosion KW - Korrosion KW - Exposure KW - Auslagerungsversuche PY - 2022 UR - https://efcweb.org/Scientific+Groups/WP25_+Atmospheric+Corrosion/Current+Activities/_/Exposure%20site%20catalogue%20EFC%20lores.pdf SP - 1 EP - 56 PB - European Federation of Corrosion, EFC AN - OPUS4-55284 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schühle, Florian A1 - Richter, Matthias T1 - Bereitstellung qualitätsgesicherter VOC-Aufnahmeraten für axiale Passivsammler N2 - Quality assured uptake rates for passive sampling of indoor air VOCs Passive sampling of VOCs with Tenax® TA and thermal desorption GC-MS analysis is a simple, cost efficient and representative method to determine VOCs concentrations in indoor air. In theory, the uptake into the passive sampler is only dependent on the diffusion coefficient of the analyte in air and the geometry of the sampler (ideal adsorption). For characterization, the uptake rate (UR) is used, defined as the ratio of the uptaken mass and the product of ambient concentration and exposure time. Various reported effective uptake rates (UR,eff) differ considerably from ideal values (UR,id). Literature values in national and international standards, are essentially sorted by the applicable exposure time, while detailed information about the corresponding concentration range is lacking. Moreover the number of itemized substances is limited. The aim of this study was to review and expand this set of uptake rates by determination of own quality assured laboratory values.The determined uptake rates are considered accurate in terms of RSD and comparability to literature values and can be recommended for exposure times of seven days at 50 100 µg/m³ (approximately 100 300 ppm min). Seven day uptake rates in ISO16017 2 and ASTM D6196 are not generally suited for this purpose, as has been exemplarily shown for benzene. N2 - Die passive Probenahme von VOC (Volatile Organic Compounds) mit Tenax® TA und Thermodesorption GC/MS Analytik ist eine einfache, kosteneffiziente und repräsentative Methode zur Bestimmung der VOC-Konzentrationen in der Innenraumluft. In der Theorie ist die Stoffaufnahme in den Passivsammler nur abhängig vom Diffusionskoeffizienten der Substanz in Luft und der Geometrie des Sammlers (ideale Adsorption). Um sie zu charakterisieren, wird die Aufnahmerate (UR), definiert als Quotient der Massenaufnahme und dem Produkt aus Konzentration und Expositionszeit, verwendet. Viele effektive Aufnahmeraten (UR,eff) unterscheiden sich beträchtlich von idealen (theoretischen) Werten (UR,id). Literaturwerte sind in nationalen und internationalen Normen lediglich für bestimmte Expositionszeiten vorgegeben, während detaillierte Informationen über den zugehörigen Konzentrationsbereich fehlen. Außerdem ist die Anzahl der insgesamt in der Literatur beschriebenen Substanzen begrenzt. Das Ziel der vorgestellten Studie ist es diesen Fundus an Aufnahmeraten zu begutachten und zu prüfen und ihn durch die Bestimmung eigener qualitätsgesicherter Laborwerte zu ergänzen. Die bestimmten Aufnahmeraten werden als akkurat bezüglich ihrer relativen Standardabweichung und Vergleichbarkeit zu Literaturwerten betrachtet und können für Expositionszeiten von 7 Tagen bei Konzentrationen von 50 100 µg/m³ (ca. 100 300 ppm min) empfohlen werden. Die Sieben Tage Aufnahmeraten aus ISO16017 2 und ASTM D6196 sind nicht generell für diesen Zweck geeignet, wie exemplarisch für Benzol gezeigt wurde. T2 - Kongress 29. WaBoLu-Innenraumtage CY - Berlin, Germany DA - 24.05.2022 KW - IAQ KW - VOC KW - Passive sampling KW - Uptake rate PY - 2022 SN - 978-3-949241-04-8 AN - OPUS4-55209 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schoknecht, Ute T1 - Leaching und Transformation von Bioziden aus Fassadenfarben N2 - Anhand von Beobachtungen aus Labor- und Freilandversuchen wurde dargestellt, wie Wasserkontakt und Strahlung die Auslaugung und Transformation der Wirkstoffe Diuron und Terbutryn beeinflussen. Auf Optionen zur modellhaften Darstellung dieser Prozesse wurde kurz eingegangen. T2 - Optimierung und Minimierung des Biozideinsatzes in Baustoffen CY - Online meeting DA - 09.02.2022 KW - Leaching KW - Transformation KW - Biozid KW - Fassadenfarbe PY - 2022 AN - OPUS4-55273 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schoknecht, Ute T1 - The Impact of Weather Conditions on Biocides in Paints N2 - Aim. The European biocidal products regulation requires environmental risk assessments for biocidal products under service conditions. This is only possible, if processes that lead to biocide emissions into the environment are understood and can be reasonably predicted. Actual emissions due to leaching result from different processes that are affected by material properties and environmental conditions. Transformation of biocides can affect emissions considerably. Leaching and possible transformation of the film preservatives carbendazim, diuron, OIT and terbutryn in paints was observed under laboratory and field conditons in order to investigate the influence of different factors, e.g. water contact and radiation on biocide emissions. The paints contained either white titanium dioxide or a red iron oxide pigment to check whether pigments affect leaching processes. Methods. Test specimens of a water-based styrene acrylic dispersion paint on glass were exposed to UVA-radiation in a UV weathering device and/or exposed to water contact by immersion events on the basis of the European standard EN 16105. Plywood panels were coated and exposed to natural weather conditions in a semi-field experiment. Concentrations of biocides and transformation products were analysed in leachates from laboratory tests, runoff samples and remaining coatings. Results. The impact of weathering conditions on transformation processes differs for the investigated active substances. Water contact, radiation as well as pigments in the paints determine the pattern and amount of transformation products on coatings, leachates and runoff water. Observations from laboratory and field experiments were compared. It proved that results from laboratory tests support understanding of data from field experiments. Detailed knowledge on the fate of active substances under environmental conditions supports manufacturers to develop safe applications of film preservatives and authorities to evaluate its environmental impact. T2 - European Technical Coatings Congress 2022 CY - Kraków, Poland DA - 12.07.2022 KW - Paints KW - Biocides KW - Transformation KW - Emission PY - 2022 AN - OPUS4-55274 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schoknecht, Ute A1 - Kalbe, Ute A1 - Happel, O. T1 - Combination of leaching tests with ecotoxicity and chemical analysis – lessons learnt N2 - The presentation describes analytical methods to characterize eluates from leaching tests and identify organic substances in leachates. Chances to obtain complementary information from ecotoxtests and chemical analysis are discussed. T2 - Workshop: Ecotoxicological evaluation of construction products – test results, implementation in Guidance, Technical Standards and Ecolabelling CY - Online meeting DA - 21.03.2022 KW - Leaching KW - Ecotoxicity KW - Construction products PY - 2022 AN - OPUS4-55276 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Light-dependent development in Botrytis cinerea N2 - Sunlight is an important environmental factor is almost all ecosystems by being a source of energy, information, and stress. All organisms must protect themselves from the harmful effects of light such as UV radiation, ROS accumulation, heat, and desiccation. Finally, light qualities and quantities can be used for decision making, timing and as guide for directed growth when they are sensed and transduced into intracellular signals. Botrytis cinerea and other plant pathogens infecting the sun-exposed parts of the plant must cope with the high light conditions the host plant seeks. Further they experience an altered light spectrum (‘green gap’) when they colonize shaded parts of the plant; it is depleted for blue and red light that is absorbed by the plant chlorophyll and enriched for green and far-red light that is reflected or transmitted by the plant tissue. As these ambient light conditions trigger the shade avoidance response in the plant, the pathogens may trigger their own ‘shading response’ such as the upregulation of virulence determinants and inoculum production. B. cinerea maintains a highly sophisticated light signaling machinery that senses different light qualities to trigger a variety of responses, that are protection, morphogenesis, positive and negative tropisms, and entrainment. These characteristics render B. cinerea a valuable model to enlighten the role of light in parasitic fungus-plant interactions and beyond. The vegetative mycelium – the core of all infection and developmental programs – is not visibly pigmented and thus considered to be sensitive to biotic and abiotic stresses. However, the vegetative hyphae have a very limited half-life and are usually restricted to the invasive growth phase in which they are protected from light by the plant tissue. Fast colonization of host tissues and by this proper nutrient acquisition enables the rapid formation of long-lasting reproduction structures (melanized conidiophores with conidia, sclerotia) on the surfaces of rotted plant tissues. Depending on the light and temperature conditions, conidiation or sclerotial development is initiated. Taken together, B. cinerea uses light-regulated signaling networks to avoid light whenever possible; for example, by minimizing the half-life of sensitive cells that are hiding in plant tissues and by scheduling critical steps such as conidiogenesis, conidial germination and penetration of plant tissues for the night. T2 - BotrySclero2022 CY - Avignon, France DA - 13.06.2022 KW - Fungus KW - Light KW - Stress KW - Melanin PY - 2022 AN - OPUS4-55248 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Fungi in extreme habitats: Lessons from the microcolonial black fungus Knufia petricola N2 - Fungi that share light-flooded habitats with phototrophs may profit from their excess photosynthetic products. But to cope with sunlight-associated stresses [e.g. high temperatures, UV radiation with associated DNA damage, accumulation of reactive oxygen species (ROS), desiccation and osmotic stresses] it is important for fungi to accurately sense and respond to changes in light. The genomes of black [dihydroxynaphthalene (DHN) melanin-containing] fungi from phyllosphere and exposed solid surfaces contain multiple photoreceptors (PRs). The plant pathogen Botrytis cinerea (Leotiomycetes) has a highly sophisticated photosensory and signalling system that helps to avoid light and to locate susceptible hosts. Rock-inhabiting Dothideomycetes and Eurotiomycetes including Knufia petricola possess equal numbers of PRs along with the same set of protective pigments. This similarity between black fungi from plant and rock surfaces suggests that photoperception and -regulation are important for fungi that receive nutrients through cooperation with phototrophs. T2 - Gordon Research Conference "Cellular and Molecular Fungal Biology" CY - Holderness, NH, USA DA - 26.06.2022 KW - Light KW - Stress KW - Photoperception KW - Pigments PY - 2022 AN - OPUS4-55249 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm ED - Leyens, C. T1 - Hygienische Eigenschaften von additiv gefertigtem 1.4404 in Trinkwasser N2 - Elektrochemische Messungen zur hygienischen Bewertung additiv gefertigter Bauteile werden diskutiert. Die Bewertung und Details des Werkstoffs werden beschrieben, Anwendungsbeispiele werden gezeigt. T2 - 3. Fachtagung Werkstoffe und Additive Fertigung CY - Dresden, Germany DA - 11.05.2022 KW - Korrosion KW - Trinkwasser KW - Hygienische Bewertung KW - Additive Fertigung PY - 2022 SN - 978-3-88355-423-2 SP - 126 EP - 127 PB - Deutsche Gesellschaft für Materialkunde (DGM) CY - Sankt Augustin AN - OPUS4-54933 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Babutzka, Martin A1 - Valet, Svenja A1 - Kotula, Stefan A1 - Burkert, Andreas A1 - Gümmer, K. A1 - Bender, S. A1 - Huckshold, M. T1 - Normentwurf für ein Prüfverfahren zur Bestimmung von Deckschichtwiderständen an Zinküberzügen mittels gelartiger Elektrolyte N2 - Das Grundproblem der heute verfügbaren und normativ geregelten Prüfverfahren für Zinküberzüge besteht neben den realitätsfernen Prüfbedingungen vor allem in der subjektiv geprägten Auswertung der Prüfergebnisse. Die systematische Betrachtung der Entwicklungen der letzten Jahre zeigt, dass die üblichen Verfahren den aktuellen Anforderungen damit schon vom Ansatz her nicht gerecht werden können und auch die bisher betriebene, fortlaufende Variation und Anpassung von Prüfbedingungen keinen grundlegend neuen Lösungsansatz bieten können. Ein solcher ergibt sich nur, wenn die Zinküberzüge hinsichtlich der kinetischen Eigenschaften der Deckschichtbildung und -auflösung umfassend beschrieben werden können, was nur durch den Einsatz elektrochemischer Untersuchungsmethoden mittels Gelelektrolyten möglich ist. Aus diesem Grund wurde im Verbundforschungsvorhaben GELELEK auf der Basis elektrochemischer Methoden unter Verwendung eines Gelelektrolyten ein Normenvorschlag für eine Prüfnorm erarbeitet und zur Normungsreife geführt, welcher den Anforderungen an ein Messsystem für Feldanwendungen entspricht. Im Verbundforschungsvorhaben GELELEK wurde eine gezielte Kombination von Laboruntersuchungen mit Untersuchungen im Feld und Bauteilen unter realen Einsatzbedingungen angestrebt. Randbedingungen für eine gesicherte Messung von atmosphärisch bewitterten Zinküberzügen unter Einsatz von Gelelektrolyten wurden erarbeitet und im Normenvorschlag festgeschrieben. Darüber hinaus wurde ein mobiles Messgerät für Messungen mit Gelelektrolyten an realen Bauteilen entwickelt. Nach Abschluss des Forschungsvorhabens steht Industrievertretern und Prüfinstituten ein wissenschaftlich gesichertes Messverfahren basierend auf Kennwerten zur Verfügung, um Zinküberzüge und deren momentane Schutzwirkung unter praxisrelevanten Bedingungen einschätzen und normativ geregelt prüfen zu können. Der vorliegende Forschungsbericht gibt einen Überblick über die Motivation zur Durchführung des Forschungsvorhabens, wichtige Arbeitsschritte, Details zur entwickelten Prüfmethode sowie Einsatzmöglichkeiten für Prüfinstitute und Unternehmen. KW - Normung KW - Zink KW - Korrosion KW - Deckschichtbildung KW - Atmosphärische Korrosion KW - Korrosionsprüfung PY - 2022 UR - https://www.gav-verzinken.de/forschung/wissenspool SP - 1 EP - 24 AN - OPUS4-54947 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Winkler, Nicolas P. A1 - Neumann, Patrick P. A1 - Kohlhoff, Harald A1 - Säämänen, A. A1 - Kangas, A. A1 - Poikkimäki, M. A1 - Schaffernicht, E. A1 - Lilienthal, A. J. T1 - RASEM - Robot-Assisted Environmental Monitoring for Air Quality Assessment N2 - This presentation was held at the SAF€RA symposium and gives an overview to the research project RASEM and its results. T2 - 2022 SAF€RA Symposium CY - Rome, Italy DA - 19.05.2022 KW - Air Pollution KW - Air Quality KW - Environmental Monitoring KW - Mobile Robot Olfaction KW - Wireless Sensor Network PY - 2022 AN - OPUS4-54953 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Schraut, Katharina A1 - Adamczyk, Burkart A1 - Weimann, Karin A1 - Gluth, Gregor T1 - Klimaschonende Bindemittel auf der Basis von Rohstoffen der Circular Economy N2 - Die Zementindustrie und weitere energieintensive Industrien wie etwa die Stahlindustrie stehen vor dem Hintergrund der Transformation unserer Gesellschaft zur Klimaneutralität vor erheblichen Herausforderungen. Ziel dieser Branchen ist perspektivisch die vollständige Vermeidung klimaschädlicher Emissionen – mit besonderem Fokus auf Kohlendioxid. Neben der Umstellung auf regenerative Energieträger, sind im Speziellen für die Zementindustrie die erheblichen Anteile an CO2-Emissionen durch die Entsäuerung von Kalkstein zukünftig zu vermeiden. Da die hervorragenden Bindemitteleigenschaften des bisher hauptsächlich in Zementen eingesetzten Portlandklinkers jedoch auf Calciumverbindungen wie Tri- und Di-calciumsilikaten basieren, stellt die Substitution des Kalks derzeit für die Zementindustrie die größte Herausforderung dar. Neben vollständig neuen Bindemittelsystemen ohne Verwendung von Kalk und CCS/CCU-Technologien zur Vermeidung der CO2-Emissionen bei Verwendung von Kalk, können Abfälle und Nebenprodukte wie etwa Betonbrechsand, verschiedene Schlacken und weitere Massenreststoffe sinnvoll zur Einsparung von Rohstoffen und zur Vermeidung von CO2-Emissionen eingesetzt werden. Es gilt diese Potentiale von Sekundärrohstoffen branchenübergreifend zu identifizieren und Synergien zwischen den Branchen nutzbar zu machen. Hierbei werden neben der chemischen Zusammensetzung der Abfälle und Nebenprodukte auch die Verfügbarkeit und der Massenstrom relevante Kriterien sein. Die potenziellen Sekundärrohstoffe und deren Gemische mit chemisch ähnlicher Zusammensetzung wie die bisher verwendeten Bindemittel, können durch verschiedene technische Ansätze wieder in reaktive Bindemittel umgewandelt und damit nutzbar gemacht werden. Eine gezielte Umwandlung der nicht reaktiven mineralischen Phasen in neue mineralische Phasen mit guten Bindemitteleigenschaften, kann u. a. durch Schmelzprozesse erzielt werden. In Schmelzen können bei hohen Temperaturen die bestehenden, nicht reaktiven mineralischen Phasen zerstört und neue mineralische Phasen mit guten Bindemitteleigenschaften erzeugt werden. Hohe Freiheitsgrade durch gezielte Einstellung der stofflichen Zusammensetzung der Schmelze, durch Stoffseparationen und durch geregelte Abkühlregimes können eine maßgeschneiderte Erzeugung neuer Bindemitteltypen ermöglichen. Aufgrund der hohen erforderlichen Temperaturen von Schmelzprozessen ist die Umsetzung dieser neuen Verfahren nach Möglichkeit in bestehenden pyrometallurgischen Produktionsrouten wie etwa der Stahlproduktion vorzunehmen. So kann etwa der Einsatz von Betonbrechsand als Schlackebildner in der Stahlproduktion zielführend sein, wenn die Schlacke wieder zu einem Bindemittel prozessiert wird und in Zementen Verwendung findet. Eine stoffliche Kreislaufführung wäre hiermit gegeben, wobei der Einsatz von Kalkstein als Schlackebildner oder Rohstoff für die Zementproduktion, und damit die entsprechenden CO2-Emissionen, vermieden werden. Die Entwicklung neuartiger Bindemittelsysteme auf Basis von Sekundärrohstoffen sollte von erforderlichen Anpassungen und neuen Entwicklungen in der Regelsetzung und Normung begleitet werden. Vor allem muss gewährleistet sein, dass die mit neuen Bindemitteln hergestellten Betone den hohen Anforderungen an Dauerhaftigkeit und Umweltverträglichkeit genügen. Des Weiteren sollte mit den etablierten Methoden, wie etwa der Lebenszyklusanalyse, untersucht werden, inwiefern und in welchem Umfang die neuen technischen Entwicklungen zu Nachhaltigkeit und Klimaschutz beitragen. T2 - GERRI - BGR Rohstoffkonferenz 2022 CY - Hannover, Germany DA - 05.07.2022 KW - Zement KW - Schlacke KW - Rotschlamm KW - Klimaneutralität PY - 2022 AN - OPUS4-55193 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa T1 - Analyseverfahren und Messhäufigkeit zur Bestimmung des Phosphorgehalts im Klärschlamm nach AbfKlärV N2 - Auf dem Betreiberforum der DWA-Plattform P-Rück wurden die Empfehlungen für den Vollzug der Phosphorrückgewinnungspflicht aus Klärschlamm vorgestellt. Diese Empfehlungen behandeln die Häufigkeit der Phosphoruntersuchungen im Klärschlamm, wo ein Jahresgang empfohlen wird und eine Empfehlung der Phosphorbestimmung über Aufschluss der Probe in der Mikrowelle und Messung mit ICP-OES. Untermauert wurden die Empfehlungen mit den Ergebnissen von Klärschlamm-Monitoring, Ringversuch und Analytikvergleich aus dem Vorhaben extraWERT. T2 - Betreiberforum der DWA-Plattform P-Rück CY - Stuttgart, Germany DA - 23.06.2022 KW - Klärschlamm KW - Ringversuch KW - Reproduzierbarkeit KW - Phosphorrückgewinnung PY - 2022 AN - OPUS4-55146 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kirsch, Klemens A1 - Matschiavelli, N. A1 - Koerdt, Andrea A1 - Stumpf, T. T1 - Microbiologically Influenced Corrosion of Cast Iron Containers for High-Level Nuclear Waste Disposal N2 - Ductile and corrosion resistant cast iron is investigated as a potential container material to store high-level nuclear waste (HLW) in deep geological repositories (DGR) in claystone bedrock. The dynamic corrosion process is dependent on the conditions present in the DGR which are influenced and/or controlled by geochemical parameters (e.g., redox potential, pH, presence of and ionic concentration in (pore-)water), physical parameters (e.g., pressure), and the influence of metabolically active microorganisms. Cast iron corrosion will occur at the intersection of container and its decontaminable coating with the bentonite backfill material which contains natural microbial populations. The conditions in a DGR are simulated in microcosm experiments to investigate the impact of microbiologically influenced corrosion (MIC); the microcosms contain: B27 bentonite, synthetic pore water, N2 or N2-CO2 atmosphere, cast iron coupons, as well as the bacterium Desulfosporosinus burensis (isolated from repository depth in Buré, France). Three coupon configurations will be used: untreated, coated with decontaminable coating, and coated with decontaminable coating which has been damaged to simulate possible damages. The microcosms will be examined for bio- and geochemical parameters, such as pH, redox potential, mineral phases, sulphate concentration, Fe(II):Fe(III), changes in microbial populations, and the corrosion process for formation of corrosion products, and potential microbial influence, after a 270-day incubation period at 25°C under anaerobic conditions. In subsequent experiments, the sorption behavior of lanthanides and actinides onto the membranes of viable cells and spores of D. burensis, as well as the surface of corroded cast iron coupons will be investigated. T2 - 8th International Workshop on Long-term Prediction of Corrosion in Nuclear Waste Systems 2022 CY - Baden, Switzerland DA - 21.06.2022 KW - Microbiologically influenced corrosion (MIC) KW - Cast iron KW - Nuclear waste disposal PY - 2022 AN - OPUS4-55154 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger A1 - Busweiler, Sabine A1 - Haustein, V A1 - von Laar, C. A1 - Haustein, T ED - Bueno-Mari, R ED - Montalvo, T ED - Robinson, W H T1 - Korynetes caeruleus (coleoptera: cleridae) for biological control of anobium punctatum (coleoptera, ptinidae) N2 - Larvae and adults of Korynetes caeruleus (de Geer 1775) (Coleoptera: Cleridae) were collected from old churches and reared in the laboratory on Anobium punctatum (de Geer 1774) (Coleoptera, Ptinidea, formerly Anobiidae). Breeding success of K. caeruleus was low, but basic parameters of this species’ developmental cycle were identified. At 21 °C and 75 % relative humidity and a four-month cold period at 4 °C, the development of K. caeruleus from egg to adult appearance lasted 2 years. The pupal stage may be reached and completed after one and a half years. Feeding on larvae of A. punctatum by larvae of K. caeruleus was observed and consisted of a combination of sucking haemolymph and consuming body parts. The sickle-like mandibles of larvae of K. caeruleus penetrate the cuticle of prey larvae followed by pumping and sucking body movements. Adult beetles of A. punctatum were not attacked by K. caeruleus larvae. Feeding behavior of adult K. caeruleus was not investigated. T2 - 10th International Conference on Urban Pests CY - Barcelona, Spain DA - 26.06.2022 KW - Cultural heritage KW - Biological pest control KW - Life history data KW - Wood protection PY - 2022 SN - 978-84-09-41424-6 SP - 34 EP - 44 AN - OPUS4-55170 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klewe, Tim A1 - Völker, Tobias A1 - Landmann, M. A1 - Wilsch, Gerd A1 - Kruschwitz, Sabine T1 - Laser-based sorting of construction and demolition waste for the circular economy N2 - Closed material cycles and unmixed material fractions are required to achieve high recovery and recycling rates in the building industry. The growing diversity of construction and demolition waste is leading to increasing difficulties in separating the individual materials. Manual sorting involves many risks and dangers for the executing staff and is merely based on obvious, visually detectable differences for separation. An automated, sensor-based sorting of these building materials could complement or replace this practice to improve processing speed, recycling rates, sorting quality, and prevailing health conditions. A joint project of partners from industry and research institutions approaches this task by investigating and testing the combination of laser-induced breakdown spectroscopy (LIBS) and visual (VIS)/ near-infrared (NIR) spectroscopy. Joint processing of information (data fusion) is expected to significantly improve the sorting quality of various materials like concrete, main masonry building materials, organic components, etc., and may enable the detection and separation of impurities such as SO3-containing building materials (gypsum, aerated concrete, etc.). Focusing on Berlin as an example, the entire value chain will be analyzed to minimize economic/technological barriers and obstacles at the cluster level and to sustainably increase recovery and recycling rates. First LIBS measurements show promising results in distinguishing various material types. A meaningful validation shall be achieved with further practical samples. Future works will investigate the combination of LIBS and VIS/NIR spectroscopy in a fully automated measurement setup with conveyor belt speeds of 3 m/s. T2 - 6th fib Congress 2022 CY - Oslo, Norway DA - 12.06.2022 KW - LIBS KW - Recycling KW - Construction and demolition waste KW - Sorting PY - 2022 AN - OPUS4-55120 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Montag, D. A1 - Adam, Christian T1 - Rechtliche Vorgaben der Klärschlammverordnung und deren Auswirkungen auf die Phosphor-Rückgewinnung N2 - Im Abfalltechnik-Ausschuss der Bund/Länder-Arbeitsgemeinschaft Abfall (LAGA) wurde eine Vollzugshilfe zur Klärschlammverordnung erarbeitet, die nach Verabschiedung durch die Umweltministerkonferenz Mitte Mai 2020 als LAGA-Merkblatt M-39 veröffentlicht wurde. Im vorliegenden vierten Arbeitsbericht der DWA-Arbeitsgruppe KEK-1.1 werden verschiedene Aspekte der ab dem Jahr 2029 geltenden Regelungen aufgegriffen und damit einige Punkte des LAGA M-39 hinsichtlich der technischen Auswirkungen für den Kläranlagenbetreiber konkret ausgeführt. KW - Klärschlamm KW - Klärschlammverordnung KW - Phosphor-Rückgewinnung PY - 2022 SN - 1866-0029 VL - 5 IS - 69 SP - 406 EP - 413 PB - Gesellschaft zur Förderung der Abwassertechnik CY - Hennef AN - OPUS4-55009 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Hüllmann, Dino A1 - Winkler, Nicolas P. A1 - Schugardt, Jan T1 - Remote Drone-to-Drone Gas Sensing: A Feasibility Study N2 - Remote gas sensors mounted on mobile robots enable the mapping of gas distributions in large or poorly accessible areas. A challenging task however, is the generation of three-dimensional distribution maps from these spatially sparse gas measurements. To obtain high-quality reconstructions, the choice of optimal measuring poses is of great importance. Remote gas sensors, that are commonly used in Robot Assisted Gas Tomography (RAGT), require reflecting surfaces within the sensor’s range, limiting the possible sensing geometries, regardless of whether the robots are ground-based or airborne. By combining ground and aerial robots into a heterogeneous swarm whose agents are equipped with reflectors and remote gas sensors, remote inter-robot gas measurements become available, taking RAGT to the next dimension – releasing those constraints. In this paper, we demonstrate the feasibility of drone-to-drone measurements under realistic conditions and highlight the resulting opportunities. T2 - 19th International Symposium on Olfaction and Electronic Nose CY - Aveiro, Portugal DA - 29.05.2022 KW - Aerial robot KW - TDLAS KW - Inter-robot measurements KW - Gas tomography KW - Plume PY - 2022 AN - OPUS4-54927 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm ED - Stojanovic, I. T1 - Hygienic assessment of SLM-printed stainless steel N2 - Electrochemical measurements for the hygienic assessment of additively manufactured products are discussed. The Assessment and details of the material are described, examples for the application are given. N2 - Elektrochemische Messungen zur hygienischen Bewertung additiv gefertigter Bauteile werden diskutiert. Die Bewertung und Details des Werkstoffs werden beschrieben, Anwendungsbeispiele gezeigt. T2 - Kormat 2022 CY - Online meeting DA - 26.04.2022 KW - Korrosion KW - Trinkwasser KW - Hygienische Bewertung KW - Additive Fertigung PY - 2022 SN - 1848-4255 SP - 21 EP - 25 PB - Proceedings of the Croatian Society for Material Protection CY - Zagreb AN - OPUS4-54932 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar T1 - Circular Economy - Materialeffizienznormen und -leitfäden N2 - Deutschland befindet sich inmitten eines umfassenden Transformationsprozesses hin zu einer klimaneutralen und nachhaltigen Wirtschaft und Gesellschaft. Sowohl das Erreichen der Klimaziele als auch die Anpassung an die Folgen des Klimawandels fordern ein rasches, bestimmtes und gleichzeitiges Handeln in vielen Sektoren und Lebensbereichen. Normen und Standards können einen wichtigen Beitrag zum Erreichen dieser Ziele leisten. So haben Normungsorganisationen weltweit mit der ISO London Declarationeinen Pakt zur Unterstützung des Klimas geschlossen. Das bestehende Normenwerk muss auf Klimawandel-Tauglichkeit überprüft und eine Überarbeitung angestoßen werden. Der Klimawandel als Querschnittsthema betrifft alle Wirtschaftszweige, und daher bieten DIN, DKE und VDI mit dieser durch Impulsvorträge eingeleiteten Diskussionsreihe eine Plattform zum Austausch über Normung als Werkzeug zum Thema Klima mit allen Akteuren. T2 - DIN/DKE/VDI-Frühstücksreihe: Klima und Normung CY - Berlin, Germany DA - 08.11.2022 KW - Circular Economy KW - Ökodesign KW - Materialeffizienz KW - Ressourceneffizienz KW - Energieeffizienz KW - Produktdesign PY - 2022 AN - OPUS4-56183 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Olbrich, Adelina-Elisa A1 - An Stepec, Biwen Annie A1 - Koerdt, Andrea A1 - Meermann, Björn T1 - Deciphering microbiological influenced corrosion processes on steel with single cell-ICP-ToF-MS N2 - Microbiologically influenced corrosion (MIC) is a highly unpredictable process dictated by the environment, microorganisms, and the respective electron source. Interaction pathways between cells and the metal surface remain unclear. The development of this novel single cell-inductively coupled plasma-time of flight-mass spectrometry analytical method and a MIC-specific staining procedure facilitate the investigation of steel-MIC interactions. With this it is possible to analyze the multi-elemental fingerprint of individual cells. The detection method revealed elemental selectivity for the corrosive methanogenic archaeal strain Methanobacterium-affiliated IM1. The interface between material and environmental analysis thus receives special attention, e.g., when considering MIC on solid steel. Hence, the possible uptake of individual elements from different steel samples is investigated. Results showed the cells responded at a single-cell level to the different types of supplemented elements and displayed the abilities to interact with chromium, vanadium, titanium, cobalt, and molybdenum from solid metal surfaces. The information obtained will be used in the future to elucidate underlying mechanisms and develop possible material protection concepts, thus combining modern methods of analytical sciences with materials research. T2 - Adlershofer Forschungsforum 2022 CY - Berlin, Germany DA - 11.11.2022 KW - Single cell KW - Microbiological influenced corrosion MIC KW - Sc-ICP-ToF-MS KW - Method development PY - 2022 AN - OPUS4-56250 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stawski, Tomasz A1 - Van Driessche, A. T1 - Particle-mediated origins of mesocrystalline disorder in calcium sulfate single crystals N2 - Calcium sulfate minerals are abundant in natural and engineered environments and they exist in the form of three hydrates: gypsum (CaSO4·2H2O), bassanite (CaSO4·0.5H2O), and anhydrite (CaSO4). Due to their relevance in natural and industrial processes, the formation pathways of these calcium sulfate phases from aqueous solution have been the subject of intensive research1. The state-of-the-art of the calcium sulfate formation mechanisms builds upon and goes beyond what we have come to appreciate in the astounding intricacy of other mineral formation processes from ions in aqueous solutions. The original, and rather naive, 'textbook' image of these phenomena, stemming from the adaptation of classical nucleation and growth theories, has increased in complexity due to the discovery of a variety of precursor and intermediate species2. These include solute clusters (e.g. prenucleation clusters, PNCs), liquid(-like) phases, as well as amorphous and nanocrystalline solids etc.. In this context, a number of studies have already revealed that nucleation in the CaSO4-H2O system is non-classical, where the formation of the different crystalline phases involves several steps including a common amorphous precursor1, 3, 4. In this contribution we show that the formation of the amorphous phase involves the aggregation of small primary particles into larger disordered aggregates exhibiting a "brick-in-the-wall" structure5, 6. The actual crystallization occurs by the restructuring and coalescence of the particles ("bricks") into a given calcium sulfate phase depending on the physicochemical conditions of the solution. Importantly, the rearrangement process does not continue until a (nearly-)perfect homogeneous single crystal is obtained. Instead it comes to a stop, or at least significantly slows down. Such a process thus yields a final imperfect mesocrystal, composed of smaller domains rather than a continuous crystal structure, within which the domains are separated by an amorphous (i.e. less ordered) calcium sulfate phase. Hence, the non-classical crystallization process of CaSO4 yields a final imperfect mesocrystal with an overall morphology resembling that of a single crystal, yet composed of smaller nano-domains. Importantly, these observations reveal that organic-free calcium sulfate mesocrystals grown by a particle mediated-pathway preserve in the final crystal structure a “memory” or “imprint” of their non-classical nucleation process, something that has been overlooked until now. Furthermore, the nano-scale misalignment of the structural sub-units within these crystals can propagate through the length-scales, and be expressed macroscopically as misaligned zones/domains in large single crystals. Indeed, by considering large anhydrite crystals from the famous Naica Mine (“Cueva de los cristales”) we observed a suite of correlated self-similar void defects spanning multiple length-scales7. These flaws, in the macroscopic crystal, stem from “seeds of imperfection” originating from a particle-mediated nucleation pathway. Hence, building a crystal could be viewed as Nature stacking blocks in a game of Tetris, whilst slowly forgetting the games core concept and failing to fill rows completely. T2 - ECCG: European Conference on Crystal Growth 7 CY - Paris, France DA - 25.07.2022 KW - Anhydrite KW - SAXS KW - Single crystal KW - Mesocrystal PY - 2022 AN - OPUS4-56276 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Egloffstein, T. ED - Burkhardt, G. T1 - Aktuelles aus der Arbeit des BAM-Fachbeirats N2 - Der Fachbeirat kommt bereits seit 13 Jahren in seiner jetzigen Form zusammen, um Zulassungsrichtlinien, weitere Dokumente und fachliche Fragestellungen zu beraten. Die Zeit bringt auch personelle Veränderungen mit sich, darüber wollen wir berichten. Derzeit wird die Zulassungsrichtlinie für Schutzschichten im Fachbeirat und in seiner Arbeitsgruppe Geotextilien und Kunststoff Dränelemente (AG Geotextilien) überarbeitet. Zudem wurde die Zulassungsrichtlinie für Kunststoffdichtungsbahnen auf den aktuellen Stand der Regelsetzung und Normung gebracht. Bestimmte Medien, die hier bei einigen Prüfungen verwendet werden, dürfen nicht mehr in der EU in Verkehr gebracht werden. Hier werden die Hintergründe und Zusammenhänge in Kürze aufgezeigt. Zuletzt wird die Diskussion in Bezug auf den Einsatz von Rezyklaten in den zugelassenen Produkten aufgeführt. T2 - Karlsruher Deponie- und Altlastenseminar 2022 CY - Karlsruhe, Germany DA - 19.10.2022 KW - Deponie KW - Abdichtungssystem KW - Schutzschichten PY - 2022 SN - 978-3-939662-31-0 VL - 42 SP - 23 EP - 32 PB - ICP Eigenverlag Bauen und Umwelt CY - Karlsruhe AN - OPUS4-56209 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelles aus der Arbeit des BAM-Fachbeirats N2 - Der Fachbeirat kommt bereits seit 13 Jahren in seiner jetzigen Form zusammen, um Zulassungsrichtlinien, weitere Dokumente und fachliche Fragestellungen zu beraten. Die Zeit bringt auch personelle Veränderungen mit sich, darüber wollen wir berichten. Derzeit wird die Zulassungsrichtlinie für Schutzschichten im Fachbeirat und in seiner Arbeitsgruppe Geotextilien und Kunststoff Dränelemente (AG Geotextilien) überarbeitet. Zudem wurde die Zulassungsrichtlinie für Kunststoffdichtungsbahnen auf den aktuellen Stand der Regelsetzung und Normung gebracht. Bestimmte Medien, die hier bei einigen Prüfungen verwendet werden, dürfen nicht mehr in der EU in Verkehr gebracht werden. Hier werden die Hintergründe und Zusammenhänge in Kürze aufgezeigt. Zuletzt wird die Diskussion in Bezug auf den Einsatz von Rezyklaten in den zugelassenen Produkten aufgeführt. T2 - Karlsruher Deponie- und Altlastenseminar 2022 CY - Karlsruhe, Germany DA - 19.10.2022 KW - Deponie KW - Abdichtungssystem KW - Schutzschichten PY - 2022 AN - OPUS4-56210 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Frenzel, Olivia A1 - Piechotta, Christian T1 - Identification of Metabolites and Transformation Products of Bisphenols N2 - Bisphenol A (BPA) is widely used in Polycarbonate (PC), Polyacrylic resins (PAR), Polysulfones (PSU), Epoxy resins (ER), and Polyetherimides (PEI). It is also used in recycled Polyvinyl chloride (PVC) [1–3]. These BPA-containing materials have a wide area of application, especially outside. All outdoor applications are exposed to a variety of environmental impacts, like temperature, solar radiation (physical influences), chemical influences (rain or ozone), biological influences (microorganisms), and mechanical influences (hail, sand). These impacts are damaging and aging the material which can be followed by leaching or migration of pollutants like Bisphenol A into the environment. Understanding the fate and behavior of the released pollutants is very important. Therefore, different transformation products of selected Bisphenols will be generated and analyzed. T2 - 33rd International Symposium on Chromatography – ISC 2022 CY - Budapest, Hungary DA - 18.09.2022 KW - Environment KW - Transformation products KW - Bisphenols KW - Metabolites KW - Wastewater PY - 2022 AN - OPUS4-56202 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Frenzel, Olivia A1 - Piechotta, Christian T1 - Identification of transformation products and metabolites of selected Bisphenols N2 - Bisphenol A (BPA) is widely used in many Polymers. Many outdoor applications are made from BPA-based materials which are exposed to a variety of environmental impacts, like temperature, solar radiation, rain, and others. This could lead to damaging and aging of the material which might cause leaching or migration of pollutants into the environment. To understand the fate and behavior different transformation products of selected Bisphenols will be generated and analyzed. T2 - Umwelt2022 CY - Emden, Germany DA - 05.09.2022 KW - Environment KW - Bisphenols KW - Transformation products KW - Metabolites KW - Wastewater PY - 2022 AN - OPUS4-56203 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Schlegel, Moritz-Caspar A1 - Rockland, Ulrike A1 - Harrer, Andrea T1 - Informationsmaterial zu Wartung und Betrieb von Getränkekühlern N2 - „Getränkekühler optimal einsetzen“: So sparen Sie die Energiekosten und schonen das Klima. Wussten Sie, dass Sie durch den Einsatz eines effizienten Getränkekühlers (Energieeffizienzklasse B) ca. 114 € pro Jahr sparen im Vergleich zu einem weniger effizienten Gerät (Energieeffizienzklasse D)? Aber nicht immer gibt es die Möglichkeit ein Neugerät anzuschaffen. Oft werden die Kühlgeräte von Getränkeherstellern zur Präsentation ihrer Waren zur Verfügung gestellt. Trotzdem tragen am Ende die Betreiber:innen die Betriebskosten der Geräte. Aber auch beim Einsatz Ihres weniger effizienten Getränkekühler gibt es verschiedene Möglichkeiten, die Energiekosten zu senken. Beispielsweise kann schon der Einsatz einer Zeitschaltuhr zu einer Stromreduzierung von bis zu 50 Prozent oder auch die richtige Platzierung der Geräte an kühlen Orten ohne Zugluft zu einem geringeren Strombedarf von bis zu 30% führen. In unserer Checkliste für die Aufstellung und das Betreiben von Getränkekühlgeräten zeigen wir Ihnen einfache Schritte, um den Energieverbrauch schnell zu senken. KW - Getränkekühler PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-561581 SP - 1 EP - 2 CY - Berlin AN - OPUS4-56158 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Haratsu, T. A1 - Neumann, Patrick P. A1 - Sakaue, M. A1 - Matsukura, H. A1 - Ishida, H. T1 - Simulating a Gas Source Localization Algorithm with Gas Dispersion Produced by Recorded Outdoor Wind N2 - This presentation reports the use of the first gas dispersion simulator capable of generating large wind fluctuation, to test a modification to a gas source localization algorithm and study how the change affects it. Gas source localization at an outdoor environment is a challenging task mainly due to the complexity of the spreading gas caused by the unpredictable nature of constantly changing wind. Therefore, a novel use of outdoor wind in developing a gas source localization system by simulation will be shared. To consider the characteristic of sudden but large and unpredictable changes in wind direction, recorded outdoor wind was used to simulate a realistic outdoor gas dispersion which has been done for the first time. With the use of this simulator, a modification to a mobile robot-based gas source localization algorithm was evaluated. Multiple simulations of the modified and the original algorithm were done to study the effect of the tested modification. The results showed that a small difference in the algorithm can greatly impact the results. From this study, we consider the use of simulation consisting of the necessary traits to evaluate outdoor gas source localization, has the potential to accelerate the development of a reliable localization system. T2 - ROBOT2022: Fifth Iberian Robotics Conference CY - Zaragoza, Spain DA - 23.11.2022 KW - Gas Dispersion Simulator KW - Gas Source Localization KW - Mobile Robot Olfaction KW - Particle Filter PY - 2022 AN - OPUS4-56413 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin A1 - Valet, Svenja A1 - Kotula, Stefan A1 - Burkert, Andreas T1 - Vorstellung des WIPANOVerbundforschungsvorhabens GELELEK: Forschungsziele und Ergebnisse N2 - Der Vortrag stellt das WIPANO-Forschungsvorhaben GELELEK vor und fasst die wichtigsten erzielten Ergebnisse zusammen. T2 - Sitzung des GfKORR Arbeitskreises „Korrosion und Korrosionsschutz von Eisen und Stahl“ CY - Online meeting DA - 08.12.2022 KW - Deckschichtbildung KW - Gelartige Elektrolyte KW - Korrosionsuntersuchungen KW - Normung KW - Ringversuch KW - WIPANO KW - Zink KW - Korrosion PY - 2022 AN - OPUS4-56502 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa A1 - Roskosch, A. A1 - Adam, Christian T1 - Ergebnisse des Vorhabens extraWERT N2 - Der Vortrag liefert eine Zusammenfassung der wichtigsten Ergebnisse des extraWERT-Vorhabens mit Schwerpunkt auf den Umsetzungsfragen zur Klärschlammverordnung. Bei diesen Punkten handelt es sich um die Untersuchung von monatlichen Phosphorschwankungen in kommunalem Klärschlamm und die Gleichwertigkeit verschiedener Verfahren zur Phosphorbestimmung in Klärschlamm. T2 - vgbe-Fachtagung Thermische Abfall-, Klärschlammbehandlung und Wirbelschichtfeuerungen 2022 CY - Hamburg, Germany DA - 09.05.2022 KW - Klärschlammverordnung KW - Phosphorrückgewinnung KW - Ringversuch PY - 2022 AN - OPUS4-54843 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Schraut, Katharina A1 - Adamczyk, Burkart A1 - Weimann, Karin A1 - Gluth, Gregor T1 - Erzeugung klimaschonender Bindemittel als Alternativen zu Zement durch thermochemische Behandlung von mineralischen Nebenprodukten und Abfällen N2 - Die Zementindustrie erzeugt etwa 6-7% der globalen CO2-Emissionen und steht damit als Industriezweig vor dem Hintergrund einer anvisierten Klimaneutralität vor gewaltigen Herausforderungen. Der Prozess der Klinkerherstellung wurde über die vergangenen Jahrzehnte bereits kontinuierlich optimiert. Seit 1990 ist es der deutschen Zementindustrie gelungen, die spezifischen CO2-Emissionen der Zementproduktion u. a. durch den Einsatz alternativer, nicht fossiler Brennstoffe und durch Absenkung des Klinkergehalts im Zement um 20 % zu senken. Weitere konventionelle Minderungsstrategien versprechen jedoch nur noch wenig zusätzliche Reduktion. Im Falle des Portlandklinkers besteht die Schwierigkeit darin, dass zwei Drittel der CO2-Emissionen rohstoffbedingt durch die Entsäuerung des Kalksteins (CaCO3) anfallen, die durch die beschriebenen Maßnahmen nicht weiter abgesenkt werden können. Vielmehr wird es erforderlich sein, noch zu entwickelnde oder zu optimierende Technologien anzuwenden und ggf. alle relevanten Ebenen wie Produktion, Weiterverarbeitung und Anwendung von Zement und Beton neu zu denken. Neben technologischen Ansätzen zur CO2-Abscheidung mit nachfolgender langfristiger Speicherung (Carbon Capture and Storage – CCS) oder Verwertung (Carbon Capture and Utilisation – CCU) werden auch alternative Rohstoffe für die Zementproduktion und alternative Bindemittel in Betracht zu ziehen sein. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 25.04.2022 KW - Zement KW - Sekundärrohstoff PY - 2022 SN - 978-3-944310-58-9 SP - 372 EP - 385 PB - TK-Verlag CY - Neuruppin AN - OPUS4-54737 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Schraut, Katharina A1 - Adamczyk, Burkart A1 - Weimann, Karin A1 - Gluth, Gregor T1 - Erzeugung klimaschonender Bindemittel als alternativen zu Zement N2 - Die Zementindustrie und weitere energieintensive Industrien wie etwa die Stahlindustrie stehen vor dem Hintergrund der Transformation unserer Gesellschaft zur Klimaneutralität vor erheblichen Herausforderungen. Ziel dieser Branchen ist perspektivisch die vollständige Vermeidung klimaschädlicher Emissionen – mit besonderem Fokus auf Kohlendioxid. Neben der Umstellung auf regenerative Energieträger, sind im Speziellen für die Zementindustrie die erheblichen Anteile an CO2-Emissionen durch die Entsäuerung von Kalkstein zukünftig zu vermeiden. Da die hervorragenden Bindemitteleigenschaften des bisher hauptsächlich in Zementen eingesetzten Portlandklinkers jedoch auf Calciumverbindungen wie Tri- und Di-calciumsilikaten basieren, stellt die Substitution des Kalks derzeit für die Zementindustrie die größte Herausforderung dar. Neben vollständig neuen Bindemittelsystemen ohne Verwendung von Kalk und CCS/CCU-Technologien zur Vermeidung der CO2-Emissionen bei Verwendung von Kalk, können Abfälle und Nebenprodukte wie etwa Betonbrechsand, verschiedene Schlacken und weitere Massenreststoffe sinnvoll zur Einsparung von Rohstoffen und zur Vermeidung von CO2-Emissionen eingesetzt werden. Es gilt diese Potentiale von Sekundärrohstoffen branchenübergreifend zu identifizieren und Synergien zwischen den Branchen nutzbar zu machen. Hierbei werden neben der chemischen Zusammensetzung der Abfälle und Nebenprodukte auch die Verfügbarkeit und der Massenstrom relevante Kriterien sein. Die potenziellen Sekundärrohstoffe und deren Gemische mit chemisch ähnlicher Zusammensetzung wie die bisher verwendeten Bindemittel, können durch verschiedene technische Ansätze wieder in reaktive Bindemittel umgewandelt und damit nutzbar gemacht werden. Eine gezielte Umwandlung der nicht reaktiven mineralischen Phasen in neue mineralische Phasen mit guten Bindemitteleigenschaften, kann u. a. durch Schmelzprozesse erzielt werden. In Schmelzen können bei hohen Temperaturen die bestehenden, nicht reaktiven mineralischen Phasen zerstört und neue mineralische Phasen mit guten Bindemitteleigenschaften erzeugt werden. Hohe Freiheitsgrade durch gezielte Einstellung der stofflichen Zusammensetzung der Schmelze, durch Stoffseparationen und durch geregelte Abkühlregimes können eine maßgeschneiderte Erzeugung neuer Bindemitteltypen ermöglichen. Aufgrund der hohen erforderlichen Temperaturen von Schmelzprozessen ist die Umsetzung dieser neuen Verfahren nach Möglichkeit in bestehenden pyrometallurgischen Produktionsrouten wie etwa der Stahlproduktion vorzunehmen. So kann etwa der Einsatz von Betonbrechsand als Schlackebildner in der Stahlproduktion zielführend sein, wenn die Schlacke wieder zu einem Bindemittel prozessiert wird und in Zementen Verwendung findet. Eine stoffliche Kreislaufführung wäre hiermit gegeben, wobei der Einsatz von Kalkstein als Schlackebildner oder Rohstoff für die Zementproduktion, und damit die entsprechenden CO2-Emissionen, vermieden werden. Die Entwicklung neuartiger Bindemittelsysteme auf Basis von Sekundärrohstoffen sollte von erforderlichen Anpassungen und neuen Entwicklungen in der Regelsetzung und Normung begleitet werden. Vor allem muss gewährleistet sein, dass die mit neuen Bindemitteln hergestellten Betone den hohen Anforderungen an Dauerhaftigkeit und Umweltverträglichkeit genügen. Des Weiteren sollte mit den etablierten Methoden, wie etwa der Lebenszyklusanalyse, untersucht werden, inwiefern und in welchem Umfang die neuen technischen Entwicklungen zu Nachhaltigkeit und Klimaschutz beitragen. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 25.04.2022 KW - Zement KW - Thermochemische Prozesse KW - Sekundärrohstoffe PY - 2022 AN - OPUS4-54738 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Glauner, R. A1 - Grosser, D. A1 - Melcher, E. A1 - Plarre, Rüdiger ED - Deutsches Institut für Normung (DIN), T1 - Kommentar zu DIN 68800-1:2019-06 Holzschutz Teil 1: Allgemeines N2 - Die Normenreihe DIN 68800 ist Ende der 2000er Jahre komplett überarbeitet worden. Der Kommentar bietet den interessierten Kreisen der Bauaufsicht, des Holzbaus, der Holzschutzmittelindustrie, der Wissenschaft, den Prüfinstituten, der Sägeindustrie, den Umweltverbänden, den Verbrauchern, den Schädlingsbekämpfern und Architekten wertvolle Hilfen bei der Anwendung und Interpretation der Norm. KW - Holzschutz, KW - DIN KW - Norm PY - 2022 SN - 978-3-410-30623-8 SP - 1 EP - 69 PB - Beuth Verlag CY - Berlin ET - 3. AN - OPUS4-54719 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger A1 - Cabral, U. A1 - Querner, P. ED - Ryder, S. ED - Crossman, A. T1 - Screening of two plant-derived extracts from Sri Lanka for their potential to control the subterranean termite Coptotermes formosanus N2 - The tropical environment of Sri Lanka accelerates bio-deterioration of cultural objects. Termites are one of the most damaging insect pests destroying the cellulose components of historical artifacts. Herbal extracts obtained from resin of Vateria copallifera (Retzius) Alston and seeds of Madhuca longifolia (Konig) Macbride have been used for centuries to preserve e.g. palm leaf manuscripts from insect attack. Herbal extractions of these traditional products for palm leaf manuscript were tested for their effect against the termite species Coptotermes formosanus Shiraki, 1909. Natural and artificial aged herbal extractions were tested to obtain a repellent index. Resin oil of V. copallifera caused slightly higher repellencies than M. longifolia. Artificially aged samples produced lower repellencies than naturally aged samples. The results indicate that the active ingredients are volatile. The potential for barrier treatment was tested only with V. copallifera. Tunnelling-behavior of C. formosanus workers through sand in the presence of V. copallifera resin oil was largely reduced. T2 - Pest Odyssey The Next Generation CY - Online meeting DA - 20.09.2021 KW - IPM in museums KW - Termite control KW - Essential oils KW - Library pests PY - 2022 SN - 978-1-909492-83-7 SP - 56 EP - 62 PB - Archetyp Publication LTD CY - London AN - OPUS4-54736 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa T1 - BAM-Projekt „extraWERT“: Gleichwertigkeit der nach AbfKlärV zulässigen Verfahren zur Phosphorbestimmung in Klärschlamm N2 - In Deutschland ist ab 2029 eine Phosphorrückgewinnung aus Klärschlamm verpflichtend. Ausgenommen sind Klärschlämme mit weniger als 20 g P/kg TM. Für die Phosphorbestimmung sind verschiedene Methoden nach Klärschlammverordnung als gleichwertig zugelassen: Der Königswasseraufschluss in der Mikrowelle und am Rückfluss sowie die Messung an ICP-OES, ICP-MS und die photometrische Bestimmung mittels Ammoniummolybdaten. An der BAM wurden die unterschiedlichen Methodenkombinationen aus Aufschluss- und Messmethode an 15 Klärschlämmen überprüft und in einem Ringversuch mit einem Klärschlamm getestet. Die Ergebnisse werden in diesem Vortrag zusammengefasst. Als Folge der Untersuchungen wird für die Phosphorbestimmung in Klärschlamm die ICP-OES-Messung nach Königswasseraufschluss in der Mikrowelle empfohlen. T2 - VDLUFA Frühjahrssitzung 2022 der Fachgruppe III Düngemittel CY - Vienna, Austria DA - 18.05.2022 KW - Ringversuch KW - Reproduzierbarkeit KW - Wiederholbarkeit KW - Phosphorrückgewinnung KW - Gleichwertigkeit Messverfahren PY - 2022 AN - OPUS4-54852 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schraut, Katharina A1 - Adamczyk, Burkart A1 - Simon, Sebastian A1 - von Werder, Julia A1 - Meng, Birgit A1 - Stephan, Dietmar A1 - Adam, Christian T1 - Formation and hydraulic reactivity of an alite rich material from post treated basic oxygen furnace slag N2 - Basic oxygen furnace slag (BOFS) is a by-product of steelmaking of which about 10.4 Mt are produced annually in the EU. BOFS is mostly used in road construction, earthwork and hydraulic engineering. However, in this use, the iron bound in BOFS is lost and the opportunity to produce higher value products from BOFS is forgone. In recent decades, many researchers have investigated a thermochemical process to reduce iron oxides to metallic iron in molten BOFS. The metallic iron formed separates from the reduced slag due to its higher density and can be recovered. An advantage of this process is that simultaneously the chemical composition of the reduced slag is adapted to that of the Portland cement clinker and the hydraulic reactive mineral alite is formed. In this study, BOFS was reduced in a small-scale electric arc furnace using petrol coke as reducing agent, and the hydraulic properties of the reduced, low-iron BOFS were investigated. Despite a chemical and mineralogical composition similar to that of Portland cement clinker, the reduced BOFS produced less heat of hydration, and its reaction was delayed compared to Portland cement. However, the addition of gypsum, as is also done in cement production from Portland cement clinker, has been found to accelerate the hydration rate of reduced BOFS. Further research to improve the hydraulic properties of the reduced slag is essential. If successful, the production of a hydraulic binder and crude iron from BOFS could have economic and ecological benefits for both the cement and steel industry. T2 - GeoMin Köln 2022 CY - Cologne, Germany DA - 11.09.2022 KW - BOFS KW - Portland Cement KW - Hydraulic reactivity PY - 2022 AN - OPUS4-56080 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gawlitza, Kornelia A1 - Kimani, Martha A1 - Kislenko, Evgeniia A1 - Rurack, Knut T1 - Fluorescent molecularly imprinted polymer particles for direct detection of glyphosate in organic solvents and water N2 - Glyphosate (GPS) is the most widely used pesticide in the world whose use increased dramatically after the introduction of genetically modified crops engineered to resist its herbicidal action during application. In recent years, there have been growing concerns over its toxicity following its classification by the International Agency for Research on Cancer (IARC) as a probable carcinogen as well as reports of its ecotoxicological effects. This resulted in increased efforts to develop quick and sensitive detection methods. In this work, molecular imprinting was combined with direct fluorescence detection of GPS by improving its solubility in organic solvents using tetrabutylammonium (TBA+) and tetrahexylammonium (THA+) as counterions. To achieve fluorescence detection, a fluorescent crosslinker containing urea binding motifs was used as a probe for GPS-TBA and GPS-THA salts in chloroform, generating stable complexes through hydrogen bond formation. The GPS/fluorescent dye complexes were imprinted into 2–3 nm molecularly imprinted polymer (MIP) shells on the surface of sub-micron silica particles. Thus, the MIP binding behavior could be easily evaluated by fluorescence titrations in suspension to monitor the spectral changes upon addition of the GPS analytes. While MIPs prepared with GPS-TBA and GPS-THA both displayed satisfactory imprinting following titration with the corresponding analytes in chloroform, GPS-THA MIPs displayed better selectivity against competing molecules. Moreover, the THA+ counterion was found to be a more powerful phase transfer agent than TBA+, enabling the direct fluorescence detection and quantification of GPS in water in a biphasic assay. A limit of detection of 1.45 µM and a linear range of 5–55 µM, which matches well with WHO guidelines for the acceptable daily intake of GPS in water (5.32 µM), have been obtained. The assay can be further optimized to allow miniaturization into microfluidic devices and shows potential for on-field applications by untrained personnel. T2 - 36th European Colloid & Interface Society Conference CY - Chania, Greece DA - 04.09.2022 KW - Glyphosate KW - Molecular Imprinting KW - Core-Shell Particles KW - Fluorescent Urea Receptors PY - 2022 AN - OPUS4-56311 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Steinhäuser, Lorin A1 - Piechotta, Christian A1 - Westphalen, Tanja A1 - Kaminski, Katja T1 - Evaluation, comparison and combination of molecularly imprinted polymer solid phase extraction and classical solid phase extraction for the preconcentration of endocrine disrupting chemicals from representative whole water samples N2 - Estrogens are endocrine disrupting chemicals and of high concerns due to demonstrated harmful effects on the environment and low effect levels. For monitoring and risk assessment, several estrogens were included in the "watch list" of the EU Water Framework Directive which sets very low environmental quality standard (EQS) levels for Estrone (E1) and 17β-Estradiol (E2) of 0.4 ng L−1 and for 17α-Ethinylestradiol (EE2) of 0.035 ng L−1 requiring sensitive detection methods, as well as extensive sample preparation. A sensitive, derivatization-free, isotope dilution calibration HPLC-MS/MS method for a panel of 5 selected estrogens (including the 3 estrogens of the EU WFD watchlist), and a procedure for the reproducible preparation of a representative whole water matrix including mineral water, humic acids and solid particulate matter are presented. These are used in a diligent comparison of classical solid phase extraction (SPE) on hydrophilic-lipophilic balanced (HLB) phase to SPE on an estrogen-specific molecularly imprinted polymer phase (MISPE) for ultra-trace levels of the analytes (1–10 ng L−1). Additionally, a two-step procedure combining HLB SPE disks followed by MISPE is evaluated. The tow-step procedure provides superior enrichment, matrix removal and sample throughput while maintaining comparable recovery rates to simple cartridge SPE. Estimated method quantification limits (MQLs) range from 0.109–0.184 ng L−1 and thus meet EQS-levels for E1 and E2, but not EE2. The representative whole water matrix provides a reproducible comparison of sample preparation methods and lays the foundation for a certified reference material for estrogen analysis. The presented method will serve as the basis for an extended validation study to assess its use for estrogen monitoring in the environment. KW - Estrogens KW - Whole water samples KW - Molecular imprinted polymers KW - EU-WFD PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-563547 DO - https://doi.org/10.1016/j.talo.2022.100163 SN - 2666-8319 VL - 6 SP - 1 EP - 5 PB - Elsevier B.V. CY - Amsterdam, Niederlande AN - OPUS4-56354 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Olbrich, Adelina-Elisa A1 - An Stepec, Biwen Annie A1 - Koerdt, Andrea A1 - Meermann, Björn T1 - Material vs. Environment: Uncovering microbiological influenced corrosion processes on steel with single cell-ICP-ToF-MS N2 - Microbiologically influenced corrosion (MIC) is a highly unpredictable process dictated by the environment, microorganisms, and the respective electron source. Interaction pathways between cells and the metal surface remain unclear. The development of this novel single cell-inductively coupled plasma-time of flight-mass spectrometry analytical method and a MIC-specific staining procedure facilitate the investigation of steel-MIC interactions. With this it is possible to analyze the multi-elemental fingerprint of individual cells. The detection method revealed elemental selectivity for the corrosive methanogenic archaeal strain Methanobacterium-affiliated IM1. The interface between material and environmental analysis thus receives special attention, e.g., when considering MIC on solid steel. Hence, the possible uptake of individual elements from different steel samples is investigated. Results showed the cells responded at a single-cell level to the different types of supplemented elements and displayed the abilities to interact with chromium, vanadium, titanium, cobalt, and molybdenum from solid metal surfaces. The information obtained will be used in the future to elucidate underlying mechanisms and develop possible material protection concepts, thus combining modern methods of analytical sciences with materials research. T2 - ToFcon 2022 CY - Online meeting DA - 17.11.2022 KW - Single cell KW - Microbiological influenced corrosion MIC KW - Sc-ICP-ToF-MS KW - Method development KW - Ir DNA staining approach KW - Carbon steel corrosion PY - 2022 AN - OPUS4-56355 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Werder, Julia A1 - Stohl, Leonie T1 - Biorezeptive Betonfassaden: Algenbiofilme als Gestaltungselement und zur Verbesserung des Stadtklimas N2 - Der Vortrag fasst den aktuellen Stand der Forschung an der BAM zum Thema "Biorezeptive Betonfassaden" zusammen. Während im Projekt Funktionsbeton der Einfluss der Textur von ultrahochfestem Beton auf die Biorezeptivität im Vordergrund steht, wird im Projekt Algenbiofilmfassade untersucht, inwieweit ein Biofilm künstlich auf Betonsubstraten etabliert werden kann. T2 - BUGG-Tag der Forschung und Lehre Gebäudegrün 2022 CY - Stuttgart, Germany DA - 10.05.2022 KW - Biofilm KW - Biorezeptivität KW - Beton KW - UHPC KW - Fassade PY - 2022 AN - OPUS4-56388 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schuehle, Florian A1 - Richter, Matthias T1 - Quality assured uptake rates for passive sampling of indoor air VOCs N2 - Generation of experimental uptake rates (UR) for > 70 VOCs (7d /100 μg m-3) Application in German Environmental Survey – VOC exposure assessment Assurance of transparency concerning UR generation and uncertainty creates basis for decision making and comparability of measurement results. Exemplarily the uncertainty u(UR) of toluene UR was modelled and determined statistically with own laboratory data (relative standard deviation of actively sampled test gas atmosphere – RSDa and n = 5 exposed passive samplers – RSDp) in line with EN 838 as well as from variation of literature UR – RSD UR,lit. T2 - Airmon 2022, 10th International Symposium on modern principles of air monitoring and biomonitoring CY - Bristol, UK DA - 06.11.2022 KW - IAQ KW - VOC KW - Diffusive sampling KW - Uptake rate PY - 2022 AN - OPUS4-56583 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Olbrich, Adelina-Elisa A1 - An Stepec, Biwen Annie A1 - Koerdt, Andrea A1 - Meermann, Björn T1 - Deciphering microbiological influenced corrosion processes on steel with single cell-ICP-ToF-MS N2 - Microbiologically influenced corrosion (MIC) is a highly unpredictable process dictated by the environment, microorganisms, and the respective electron source. Interaction pathways between cells and the metal surface remain unclear. The development of this novel single cell-inductively coupled plasma-time of flight-mass spectrometry analytical method and a MIC-specific staining procedure facilitate the investigation of steel-MIC interactions. With this it is possible to analyze the multi-elemental fingerprint of individual cells. The detection method revealed elemental selectivity for the corrosive methanogenic archaeal strain Methanobacterium-affiliated IM1. The interface between material and environmental analysis thus receives special attention, e.g., when considering MIC on solid steel. Hence, the possible uptake of individual elements from different steel samples is investigated. Results showed the cells responded at a single-cell level to the different types of supplemented elements and displayed the abilities to interact with chromium, vanadium, titanium, cobalt, and molybdenum from solid metal surfaces. The information obtained will be used in the future to elucidate underlying mechanisms and develop possible material protection concepts, thus combining modern methods of analytical sciences with materials research. References. T2 - Future WiNS CY - Berlin, Germany DA - 07.12.2022 KW - Single cell KW - Microbiological influenced corrosion MIC KW - Sc-ICP-ToF-MS KW - Method development KW - Ir DNA staining approach KW - Carbon steel corrosion PY - 2022 AN - OPUS4-56567 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute A1 - Tavernaro, Isabella A1 - Nirmalananthan-Budau, Nithiya T1 - Functional molecular chromophores and nanomaterials reporters, optical probes, and sensors N2 - •Overview of expertise of division Biophotonics •Functional molecular and nanoscale luminescent reporters, probes, and sensors including design principles available from division Biophotonics •Examples for pH and O2 responsive molecular probes and particle sensors •Surface group quantification Analytical methods and cleavable probes •Concepts & standards for the validation and traceability of optical measurements T2 - FU-Seminar CY - Berlin, Germany DA - 09.12.2022 KW - Particle sensors KW - Surface group quantification KW - Nanoscale luminescent reporters KW - Cleavable probes PY - 2022 AN - OPUS4-56526 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meermann, Björn T1 - Single cell ICP-ToF-MS as a powerful tool in environmental and material research N2 - Materials are key for our modern communities. In particular metals play important roles in all areas of our daily life - from building materials to high tech products. Due to the increasing consumption of metals and corresponding waste production, an elevated release into the environment takes place. Furthermore, metals in direct contact with the environment undergo corrosion leading to a release into the (aquatic) environment. Thus, lifespan of products/buildings are substantially reduced – hence unnecessary economic costs arise. Thus, research in this regard is needed within the force field of metal/material - environment. Evaluating the environmental impact of materials as well as developing “safe” materials, new analytical methods are highly needed. One promising powerful tool is single cell-ICP-ToF-MS for multi-elemental analysis on a single cell/organism level. Within this presentation the concept, strength as well as challenge of single cell-ICP-MS are briefly introduced. Two application examples are presented: (i) assessing the environmental impact of metals and (ii) the impact of the environment on metal-based materials and the derivation of potential environmental-friendly material protection strategies. These applications highlight the strength of new analytical approaches to explore the durability and safety of newly developed materials. Thus, analytical chemistry is one corner stone to transformation of modern society into circular economy (CEco). (i) Diatoms are located at the bottom of the food chain. Thus, toxicological relevant metals taken up by diatoms possibly accumulate within the food web causing harmful effects. Diatoms are common test system in ecotoxicology. To investigate potential metal uptake and effects, we developed an on-line single cell-ICP-ToF-MS approach for multi-elemental diatom analysis. Our approach is a new potential tool in ecotoxicological testing for metal-based materials. (ii) Next to classical corrosion processes, microorganisms are responsible for so called microbially influenced corrosion (MIC). MIC is a highly unpredictable process relying on interaction pathways between cells and the metal surface. Sheding light on MIC processes and derivate potential protection strategies, we applied single cell-ICP-ToF-MS for MIC research on a single bacteria/archaea level. It turned out that microorganism are taking up particular metals from alloys - thus, single bacteria-ICP-ToF-MS will enable development of corrosion protection strategies. T2 - SCIX 2022 CY - Cincinnati, OH, USA DA - 02.10.2022 KW - Single cell-ICP-ToF-MS KW - Algae KW - MIC PY - 2022 AN - OPUS4-56542 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 52, Heft 1 T3 - Amts- und Mitteilungsblatt der BAM - 1/2022 PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-545287 SN - 0340-7551 VL - 52 IS - 1 SP - 1 EP - 54 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-54528 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar T1 - Ökodesign und Circular Economy - Normungsroadmap C-Eco, Normung zu ErP und Ressortforschung N2 - (i) Überblick zum aktuellen Stand der Normung und aktuellen Normungsvorhaben im Bereich Ökodesign. (ii) Vorstellung des Forschungsprojektes (Steigerung der produktbezogenen Energie- und Ressourceneffizienz) vor allem in Hinblick auf Vorhaben die sich auf die Langlebigkeit, Reparierbarkeit und Recyclingfähigkeit. T2 - Expertenforum „Global Environmental Compliance“ - Fraunhofer IPA CY - Stuttgart, Germany DA - 24.03.2022 KW - Circular Economy KW - Ecodesign KW - Produkteffizienz KW - Materialeffizienz KW - Ressourceneffizienz KW - Ressortforschung KW - WUP PY - 2022 AN - OPUS4-54532 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin A1 - Haacke, Nasrin T1 - Forschungsprojekt RUNOFF: "Neubewertung der Dauerhaftigkeit von Dach- und Fassadenmaterialien und des Eintrags von Schwermetall-Ionen in die Umwelt hervorgerufen durch Runoff„ N2 - Bei Betrachtungen zur Lebensdauer von Metallbauteilen im Bauwesen müssen Korrosions- und Runoff-Vorgänge an der Atmosphäre als verschiedene Reaktionen unterschieden werden. Korrosion ist der Prozess, der von elektrochemischen Reaktionen an der Grenzfläche Metall/Patina kontrolliert wird. Runoff dagegen wird durch chemische Reaktionen an der Grenzfläche Patina/Atmosphäre begünstigt. Mit zunehmender Bewitterungszeit nimmt die Korrosionsgeschwindigkeit stetig ab, während postuliert wird, dass die Geschwindigkeit des Runoffs über die gesamte Zeit konstant bleibt. Dieses Verhalten des Runoffs muss aber zunehmend bezweifelt werden. Die Gesamtmenge an abgezehrtem Metall beinhaltet zwei Bestandteile. Ein Teil wird in die Schicht aus Korrosionsprodukten eingebaut, der andere wird aufgrund von Niederschlägen aus der Patina gelöst. Aus diesem Grund ist die Menge an Zink-Runoff stark abhängig von den Eigenschaften der Korrosionsprodukt- bzw. Patinaschicht und nicht anhand der Zusammensetzung des Metalls abschätzbar. Vorhandene Modelle können die Menge an Runoff, und damit verbunden die Abzehrung einer Schicht aus Zink und Kupfer, sowie den resultierenden Eintrag von Schwermetallionen in die Umwelt nicht mehr darstellen und erklären. Um den Korrosionsschutz an Bauwerken zum einen dauerhaft unter Beachtung von Kostenaspekten und Ressourcenschonung und zum anderen unter ökologischen Gesichtspunkten auslegen zu können, müssen deshalb neue wissenschaftliche Grundlagen erarbeitet und die Mechanismen beschrieben werden. Das BAM-Forschungsvorhaben RUNOFF widmet sich den Fragestellungen. Der Vortrag gibt einen kurzen Überblick zum Forschungsvorhaben. T2 - 19. Projektetage der Bauforschung CY - Online meeting DA - 22.03.2022 KW - Runoff KW - Zink KW - Korrosion KW - Kupfer PY - 2022 AN - OPUS4-54580 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia A1 - Breitenbach, Romy A1 - Erdmann, Eileen A1 - Gerrits, Ruben A1 - Heeger, Felix A1 - Nitsche, Sarah A1 - Tonon, Chiara A1 - Voigt, Oliver A1 - Gorbushina, Anna T1 - Knufia petricola – a model for exploring the biology of black rock-inhabiting fungi N2 - Black fungi also called black yeasts, rock-inhabiting fungi or microcolonial fungi are a group of Ascomycetes [Eurotiomycetes, Arthoniomycetes and Dothideomycetes] that exhibit high stress tolerance, yeast‑like or meristematic growth, and constitutive 1,8-dihydroxynaphthalene (DHN) melanin formation. They dominate a range of hostile natural and man‑made environments – from desert rocks and salterns to dishwashers, roofs, and solar panels. Due to their slow growth and the lack of sexual cycles and genetic tools, the underlying mechanisms of black fungi’s phenotypic traits have remained largely unexplored. We consider the rock inhabitant K. petricola [Eurotiomycetes, Chaetothyriales] a suitable model for studying the phenotypic characteristics of black fungi. With K. petricola the regulation of pigment synthesis, general stress responses and the unusual modes of cell division can be dissected by advanced reverse and forward genetics approaches. The genome of K. petricola strain A95 was sequenced using a combination of short high quality Illumina reads and long PacBio reads. The final assembly consists of twelve contigs: five complete chromosomes and six contigs with one telomer each. Gene annotation supported by transcriptomics and proteomics data was manually curated. Recently, we developed a set of genetic tools to manipulate the genome for analyzing gene functions and studying the cell biology. This set includes CRISPR/Cas9-based genome editing and live-cell imaging using genetically encoded fluorescent proteins, as well as protocols for -omics approaches and for simulation of mineral weathering in the laboratory. Mutants defective in DHN melanogenesis, carotenogenesis or both processes are currently studied to elucidate the role of these protective pigments in tolerance of natural and man-made stresses, weathering of olivine, penetration of marble, and adhesion to surfaces. Further, the established protocols and knowledge gained from K. petricola form a starting point for making other extremotolerant black fungi accessible to genetic manipulation. T2 - 31st Fungal Genetics Conference CY - USA, CA, Pacific Grove DA - 15.03.2022 KW - Black fungi KW - Melanin KW - Genome editing PY - 2022 AN - OPUS4-54585 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erdmann, Eileen A1 - Nitsche, Sarah A1 - Gorbushina, Anna A1 - Schumacher, Julia T1 - Tools for Knufia petricola: new techniques for CRISPR/Cas9-based genome editing N2 - Black microcolonial fungi represent a group of ascomycetes with similar adaptations for existing in natural and anthropogenically created extreme habitats. They exhibit slow yeast-like or meristematic growth, do not form specialized reproduction structures and accumulate the black pigment 1,8-dihydroxynaphthalene (DHN) in the multilayered cell walls. We chose the rock inhabitant Knufia petricola of the Chaetothyriales as a representative for developing methods for genetic manipulation, simulation of mineral weathering and study of symbiotic interactions. Here, we report on the expansion of the genetic toolkit by more efficient multiplex CRISPR/Cas9 using a plasmid-based system for expression of Cas9 and multiple sgRNAs and three additional resistance selection markers. The targeted integration of expression constructs by replacement of essential genes for pigment synthesis allows for an additional color screening of the transformants. The black-pink screening due to the elimination of pks1 (melanin) was applied for promoter studies using GFP fluorescence as reporter, while the black-white screening due to the concurrent elimination of pks1 (melanin) and phs1 (carotenoids) was used to identify transformants that contain the two expression constructs for co-localization or bimolecular fluorescence complementation (BiFC) studies. In addition, two intergenic regions (igr1, igr2) were identified in which expression constructs can be inserted without causing obvious phenotypes. Plasmids of the pNXR-XXX series (Schumacher, 2012) and new compatible entry plasmids were used for fast and easy generation of expression constructs and are suitable for use in other fungal systems as well. T2 - 31st Fungal Genetics Conference CY - USA, CA, Pacific Grove DA - 15.03.2022 KW - Microcolonial fungi KW - Genetic engineering KW - Fluorescent proteins PY - 2022 AN - OPUS4-54586 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Materials in contact with drinking water and regulatory issues N2 - The state of play in regard to regulations of materials in contact with drinking water in europe is discussed T2 - Kormat 2022 CY - Online meeting DA - 26.04.2022 KW - Korrosion KW - Trinkwasser KW - Hygiene KW - Risikobewertung PY - 2022 AN - OPUS4-54710 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -