TY - CONF A1 - Drago, C A1 - Wiesner, Yosri A1 - Braun, U A1 - Giovannozi, A A1 - Fadda, M A1 - Putzu, Mara A1 - Lorenzo, S A1 - Moscoso-Pérez, C A1 - Benismail, N A1 - Palma, C A1 - Almeida, J A1 - Mattarozzi, M A1 - Barbaresi, M A1 - Piergiovanni, M A1 - Masino, M A1 - Bianchi, F A1 - Careri, M A1 - v Bavel, B A1 - Maltseva, A A1 - Sillanpää, M A1 - Pröfrock, D A1 - Wippermann, D A1 - Altmann, Korinna T1 - Harmonisation of sample preparation for microplastic analysis: Recovery rates of tablets containing microplastics as reference material for food and environmental matrix N2 - Microplastic are found ubiquitarians in the environment and food products. Up to now, their impact of risks on health and environment is still controversially discussed, but based on the precautionary principle alone, their presence should be monitored and emission should be reduced (see here also the status of existing EU regulations ). The crucial point is not only the reduction of microplastics pollution but also the introduction of legally binding, standardized procedures for their analysis. The limited availability of certified reference material as well as absence of standard operating procedures to identify, characterize and quantify microplastics according to number and mass have generated lack of comparability between different analytical methods and laboratories; but also, the need of time-consuming development of own protocols for each laboratory. Further on, harmonisation and standardisation of microplastics analysis requires specific reference materials that are used to validate the measurement and to ensure the comparability of results. In the first step, we developed tablets of a water-soluble matrix, containing defined numbers of microplastic particles or mass contents. These can be solved in water and can be handled as reference materials in bottled drinking water without additional sample preparation. These samples can be measured, using mass-based methods as thermo-analytical methods like thermal desorption-gas chromatography-mass spectrometry (TED-GC/MS) or pyrolysis–gas chromatography–mass spectrometry (Py-GC/MS) and using umber-based methods as vibrational spectroscopy like Infrared and Raman directly after filtration. The aim of this work was to delevop standard operating procedure to measure microplastics in more complex matrices and to harmonise and compare different detection and characterization methods. In fact, these matrices require different additional treatments to allow a reliable quantification and identification of microplastics. T2 - SETAC Europe 2025 CY - Vienna, Austria DA - 11.05.2025 KW - Microplastics KW - Nanoplastics PY - 2025 AN - OPUS4-63366 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Freshwater compartments: Screening method for polymer identification and mass contents of microplastic particles using TED-GC-MS N2 - The pathways of plastics, especially of microplastic (MP), in environmental compartments, particularly in aquatic systems, are not well understood. The critical point is the lack of fast, harmonised methods for sampling, sample preparation and sample analysis. These three analytical steps are dependent on one another and must be optimised. In recent years, we developed a method for representative sampling and fast detection of MP in aqueous systems. The sampling in different freshwater bodies is performed in the field with a fractionated filtration system using mesh sizes of 500, 100 and 50 µm. For water with an intermediate or high content of suspended particular matter a minimum of 1000 L has to be filtered. In the lab, mesh sizes of 10 and 5 µm are used for further filtration. Subsequently, the water filtrates of the different particle size classes are sterilised, dried, weighed and homogenised, if necessary. Conventional methods for MP analysis are infrared and raman spectroscopy, giving information on the shapes and numbers of individually identified MP particles. Our focus is on the determination of mass contents of various polymers potentially contained in environmental samples. For qualitative and quantitative MP detection TED-GC-MS is used, a two-step method based on gas chromatography-mass spectrometry (GC-MS) with previous thermal extraction. This method not only enables us to screen the samples for characteristic marker-molecules, thus identifying single polymers, but furthermore allows the calculation of mass contents of individual polymers. In the present work, different freshwater compartments were exemplarily studied to identify containing polymers and calculate their mass content in MP particles. T2 - MICRO2018 CY - Lanzarote, Spain DA - 19.11.2018 KW - Microplastic KW - TED-GC-MS KW - Mass contents PY - 2018 AN - OPUS4-46739 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna A1 - Barthel, Anne-Kathrin T1 - The use of reference material in microplastic research: general aspects N2 - Discussions in science, politics and public media about microplastic in the Environment and its unclear effects for animals and humans are common these days. Although microplastic findings in water, soil and even air are well known, no general estimations about the quality or quantity of microplastic particles in environment exit. Research is necessary to develop reliable and traceable, harmonized protocols for sampling, sample preparation and fast, but accurate analysis for qualitative and quantitative measurement of microplastic in various environmental matrices. For development of such reliable and traceable methods, the use of microplastic reference materials is necessary to assess various concepts. These microplastic reference particles should be an appropriate reflection of the microplastic particles found in environment. Due to the high use in industrial products six polymers seem to be relevant in environment as microplastic particles: polyethylene (PE), polypropylene (PP), polystyrene (PS), polyethylene terephthalate (PET), polyamide (PA) and polyvinylchloride (PVC). The raw source of These thermoplastic materials are pellets or granulate with dimensions of 1 to 5 mm in diameter. Most common they own a regular cylindrical shape or are prolate sphericals. These can be bought cost-efficient by various polymer producers. But discussions in microplastic research topic lead to particle sizes down to 1 μm. Furthermore, various unregular shapes and geometries of the particles have to be considered as well as an oxidized surface. In the present work we engage the acquisition and production of realistic reference material. Different aspects should demonstrate the complex and difficult task of generating approriate, cost-efficient and well-defined reference materials. The particle size distribution by using different particle sizing methods as well as individual particle shapes are documented. Different material properties were addressed. PE, PS and PA were chosen as typical and relevant microplastic with opposite individual material characteristics in density and glass Transition temperature. The easiest possibility for acquisition of small microplastic particles is the purchase of polymer emulsion particles (20 to 150 μm). An alternative possibility to produce small microplastic particles is milling under liquid nitrogen conditions in cryo mills. Particles purchased or self-made differ strongly in shape and size depending on production method. SETAC T2 - SETAC CY - Brussels, Belgium DA - 08.05.2017 KW - Microplastics KW - Reference materials KW - Particles PY - 2017 AN - OPUS4-40264 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - van den Berg, A. A1 - Adriaans, K. A1 - Hoppener, E. A1 - Parker, L. A1 - Boersma, A. A1 - Altmann, Korinna A1 - Legler, J. A1 - Pieters, R. T1 - Inflammation-related key events stimulated by micro- and nanoplastics N2 - The presence of micro- and nanoplastic particles (MNP) in our environment has raised increasing public and political concern. Increasing evidence suggests that humans are exposed to these MNP, mostly via inhalation or ingestion. The EC-Horizon project POLYRISK (https://polyrisk.science) aims to establish an IATA/AOP-based tiered approach to assess human health risks of MNP. In our research, we focus on assessing immunotoxicological effects of MNP. We have tested a series of primary, secondary, environmentally aged (incubated in River Rine water) and chemically altered MNP for their potential to affect dendritic cells or macrophages. MNP used in this study include primary and weathered PS, secondary PVC, PA, PP (with or without talc) and PE. The secondary PE and PP (w/o talc) particles appeared to have oxidized groups on their surface. Data shows that MNP can be engulfed by macrophages (PMA-stimulated human THP1 cells) and human blood-derived dendritic cells (DCs). The effects of virgin as well as secondary MNP (0, 10 or 100 μg/ml) on THP1 macrophages were limited to decrease of mitochondrial activity (Alamar blue), increase of cellular leakage (LDH), and stimulation of lysosomal activity. None of these MNP stimulated gene expression of NFκB or release of pro-inflammatory cytokines (IL-6, TNFα, IL-1β). On the other hand, secondary PP and PE with oxidized surface groups did increase NFκB gene expression and release of cytokines by THP1 macrophages. Virgin and weathered PS particles were tested using DCs, and only weathered PS did stimulate DC activity (increased costimulatory molecules CD83, CD86) and as consequence allogeneic T cells. DC activation appeared to result from environmental contaminants. In conclusion, of all MNPs tested only those that contained active surface groups or environmental components appeared to be immunostimulatory, whereas primary and secondary MNP rather reduced macrophage activity and viability (at relatively high concentrations of 100 μg/ml). Further research is needed to reveal molecular mechanisms and to translate in vitro findings to real-world exposure scenarios. T2 - 58th Congress of the European Societies of Toxicology (EUROTOX 2024) CY - Copenhagen, Denmark DA - 08.09.2024 KW - Micro- and nanoplastic particles (MNP) KW - Human health risks KW - Immunotoxicological effects PY - 2024 DO - https://doi.org/10.1016/j.toxlet.2024.07.052 AN - OPUS4-63363 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Plastik in Böden: Mikroplastik-Ergebnisse N2 - In diesem Vortrag geht um die Vorstellung der Ergebnisse des UBA Projektes Plastik in Böden. Es werden Mikroplastik-Gehalte in verschiedenen Böden präsentiert. T2 - Fachgespräch "Plastik in Böden" CY - Online meeting DA - 28.03.2022 KW - Mikroplastik KW - Mikroplastik Böden KW - Mikroplastik-Analytik PY - 2022 AN - OPUS4-54648 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Mikroplastik an der BAM: TED-GC/MS und Referenzmaterialien N2 - Thema ist die Funktionsweise der TED-GC/MS als Methode für die Mikroplastik-Detektion sowie die Herstellung dazugehöriger Referenzmaterialien an der BAM T2 - 25. Kolloquium Massenspektrometrie von Polymeren CY - Online meeting DA - 17.06.2021 KW - Mikroplastik KW - TED-GC/MS KW - Referenzmaterial PY - 2021 AN - OPUS4-52835 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Mikroplastik Referenzmaterial und erste Vergleichsuntersuchungen N2 - Hierbei geht es um die Vorstellung von ersten Möglichkeiten um Referenzmaterial für die Mikroplastik-Analytik herzustellen und die Ergebnisse erster Vergleichsversuche. T2 - EUROLAB-D Workshop: Mikroplastik in der Praxis CY - Online meeting DA - 30.11.2021 KW - Mikroplastik KW - Referenzmaterial KW - Vergleichsversuche PY - 2021 AN - OPUS4-53880 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Systemverständnis und Untersuchungsstrategien von Kunststoffeinträgen in die Umwelt – Ergebnisse des RUSEKU-Forschungsprojektes N2 - Ziel des Vortrages ist die Vermittlung der Herausforderungen der Mikroplastik-Analytik sowie der Harmonisierung der Analytik und des Ergebnistransfers in die Normung. T2 - Jahresabschluss-Sitzung GA "Mensch und Umwelt" CY - Online meeting DA - 24.11.2021 KW - Mikroplastik KW - Mikroplastik-Analytik PY - 2021 AN - OPUS4-53830 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Plastik in Böden: Mikroplastik-Analytik N2 - Im Vortrag wir eine Methode zur Analyse von Mikroplastik in Böden dargestellt. Es geht dabei um die Probenvorbereitung und Detektion. T2 - Fachgespräch "Plastik in Böden" CY - Online meeting DA - 28.03.2022 KW - Mikroplastik KW - TED-GC/MS KW - Mikroplastik-Analytik KW - Methodenentwicklung Böden PY - 2022 AN - OPUS4-54646 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Harmonisation efforts of the CUSP projects N2 - The talk is about harmonisation approaches within CUSP. First the five H2020 projects for research on risk assessment regarding microplastics topic were presented. Secondly, harmonisation process were discussed. T2 - VAMAS SC 47 Meeting CY - Turin, Italy DA - 19.10.2022 KW - Microplastics KW - Harmonisation KW - Nanoplastics KW - H2020 KW - Risk assessment PY - 2022 AN - OPUS4-56077 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Detektion von Mikroplastik N2 - In dem Vortrag geht es um die Möglichkeiten der Detektion von Mikroplastik im Allgemeinen. Es werden Beispiele für die Luft gezeigt. T2 - VDI-Workshop „Mikroplastik in der Außenluft – Was wir wissen und was wir (noch) nicht wissen CY - Online meeting DA - 15.11.2022 KW - Mikroplastik KW - Mikroplastik in Luft KW - Detektion von Mikroplastik PY - 2022 AN - OPUS4-56289 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Needs, concepts and state of the art: Top-down production of reference materials for micro- and nanoplastics and their use in harmonisation processes N2 - The talk explains the top-down production of materials suitable for mircoplastics and nanoplastics and the use in ILCs. T2 - EUROLAB webinar: MICROPLASTICS: regulations, standards and the role of laboratories CY - Online meeting DA - 15.02.2023 KW - Microplastics KW - Nanoplastics KW - ILC KW - Milling PY - 2023 AN - OPUS4-57008 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - PlasticsEurope - plastic powders - Reference materials N2 - The talk gives ideas about possible collaboration between BAM and PlasticEurope and their BRIGID project. T2 - Project meeting of BRIDGIT project of PlasticsEurope CY - Online meeting DA - 01.02.2023 KW - Microplastics KW - PlasticEurope PY - 2023 AN - OPUS4-57012 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Stakeholder Workshop – Plastictrace WP1 N2 - The talk is about WP1 in the PlasticTrace project funded by Euromat. The projects harmonizes microplastic analysis by developing SOPs and reference materials. WP1 is responsible for material selection and preparation. All particles are homogeneity and stability checked according to ISO guide 35. T2 - Stakeholder workshop of PlasticTrace project CY - Online meeting DA - 14.12.2022 KW - Microplastic KW - Microplastics standardisation KW - Reference materials PY - 2022 AN - OPUS4-56772 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Release of synthetic fibres during washing of typical household textiles: Findings from washing machine tests and resulting policy recommendations N2 - This talk summarizes the experimental setup and the results of one washing experiment under realistic conditions according to microplastic fiber release. T2 - Tackling microplastics in the environment CY - Brussels, Belgium DA - 09.03.2023 KW - Microplastics KW - Fibers of textile origin KW - Washing machine KW - Microplastic fibre release PY - 2023 AN - OPUS4-57204 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Welche Rolle spielen Textilien als Mikroplastik-Quelle im Abwasser? Was kann man dagegen tun? N2 - Diskutiert wird die Frage, ob Textilien gewaschen in der Waschmaschine ein Eintragspfad von Mikroplastik in die Umwelt sind. Nachgewiesen wird dies experimentell über Messungen zur Massenbestimmung mit der TED-GC/MS. T2 - DWA-Seminar: Mikroplastik in der (Siedlungs-)Wasserwirtschaft – Einordnung und Handlungsempfehlungen für die Praxis CY - Online meeting DA - 29.11.2023 KW - Mikroplastik KW - TED-GC/MS KW - Waschmaschine KW - Polymer 3R PY - 2023 AN - OPUS4-59279 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Current projects in risk assessment and harmonisation N2 - The talk gives an overview about EU projects currently running for risk assessment and harmonisation in microplastic analysis. T2 - Micro- and Nanoplastics CY - Halle (Saale), Germany DA - 01.11.2023 KW - Microplastics KW - Harmonisation in microplastics KW - Polymer 3R PY - 2023 AN - OPUS4-58766 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Welche Rolle spielen Textilien als Mikroplastik-Quelle im Abwasser? N2 - In diesem Vortrag wird die Rolle der Waschmaschine als Eintragspfad von Mikroplastik in das Abwasser diskutiert und eine experimentelle Annäherung an das Problem beschrieben. T2 - Wasserwirtschaftliches Kolloquium der TU Berlin CY - Berlin, Germany DA - 14.12.2023 KW - Mikroplastik KW - TED-GC/MS KW - Waschmaschine PY - 2023 AN - OPUS4-59278 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Understanding ageing mechanism of glass fiber sizing for composite materials N2 - We analyzed the ageing of glass fiber sizing due to the influence of temperature or humidity effects and presented a possibly degradation mechanism. T2 - PDDG CY - Taormina, Sizilien, Italy DA - 04.09.2017 KW - Composite materials KW - Glass fiber sizing KW - Ageing KW - Degradation mechanism PY - 2017 AN - OPUS4-41875 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Repräsentative Untersuchungsstrategien für ein integratives Systemverständnis von spezifischen Einträgen von Kunststoffen in die Umwelt (RUSEKU) N2 - Der Vortrag wurde im Rahmen der Abschlusskonferenz des Forschungsschwerpunktes "Plastik in der Umwelt" des BMBF gehalten. Er fasst die Ergebnisse des Verbundprojektes RUSEKU zusammen. Es wurde die Herstellung verschiedener Testmaterialien für die Mikroplastik (MP) Analytik beschrieben. Im weiteren geht es um verschiedene Ansätze MP kostengünstig und schnell zu detektieren, z.B. mit Nahinfrarotspektroskopie. Nanoplastik konnte mit der Transmissionselektronenmikroskopie sichtbar gemacht werden. Für die praxisnahe Beprobung von Gewässern wurde die Fraktionierte Filtration entwickelt. Integrale Beprobungen können mit dem Sedimentationskasten erfolgen. Als Beispiele für die Beprobung realer Gewässer wurde das urbane Abwassersystem Kaiserslautern, Getränkewasser und Waschmaschinenwasser gezeigt. T2 - Abschlusskonferenz des Forschungsschwerpunktes "Plastik in der Umwelt" des BMBF CY - Online meeting DA - 20.04.2021 KW - Mikroplastik KW - TED-GC/MS KW - Probennahme KW - RUSEKU PY - 2021 AN - OPUS4-52546 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Microplastics at BAM: TED-GC/MS and reference materials N2 - Thsi talk aims to present the activities of microplastic analysis at BAM according to TED-GC/MS and reference materials developement. T2 - Webinar BAM / University of Birmingham CY - Online meeting DA - 15.06.2021 KW - Microplastic KW - TED-GC/MS KW - Reference materials PY - 2021 AN - OPUS4-53738 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Mikroplastik – Ein Problem für die Menschheit? N2 - Mikroplastik findet sich in Ozeanen, Seen, Flüssen und Bächen. Es kann in unserem Boden, in der Luft und sogar in Organismen nachgewiesen werden. Jedes Jahr werden weltweit Millionen Tonnen freigesetzt. Doch wo und wie landet Mikroplastik in der Umwelt? Und wie können wir diese winzigen Partikel nachweisen? T2 - Berlin Science Week CY - Berlin, Germany DA - 01.11.2021 KW - Mikroplastik KW - TED-GC/MS PY - 2021 AN - OPUS4-53734 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna A1 - Braun, U. T1 - Monitoring von Mikroplastik N2 - Der Vortrag gibt einen Überblick was bei der Analyse von Mikroplastik zu beachten ist und beschreibt die Vor- und Nachteile der TED-GC/MS. T2 - Abschlusstreffen MikroPlaTas CY - Online meeting DA - 23.06.2021 KW - Mikroplastik KW - TED-GC/MS KW - Mikroplastik-Analytik PY - 2021 AN - OPUS4-52916 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Production of reference materials using a quality by design approach N2 - Accurate analysis of microplastics is based on validated methods and the use of standardized protocols. Therefore, reference materials are essential to determine recovery rates and optimise the existing workflows. The reference materials should mimic the reality in terms of particle properties and concentration and are intended for a special use. The Quality-by-Design approach helps to select the users need and defines a target product profile with mandatory and desired particle properties. We will address different reference material top-down production processes with their limits and challenges for production of materials varying in size ranges of micro- and nanoplastics. T2 - OECD Workshop on Nanoplastics CY - Paris, France DA - 12.11.2025 KW - Microplastics KW - Reference materials KW - Nanoplastics KW - Quality-by-Design PY - 2025 AN - OPUS4-64717 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dailey, L. A. A1 - Altmann, Korinna A1 - Ćirković Veličković, Tanja T1 - Exposition und Detektionstechniken: Der Weg zur Harmonisierung N2 - Der Vortrag gibt einen Überblick über Erkenntnisse der WG 1 und WG 3 des CUSP Clusters der Horizon Europe Projekte von Mikroplastik (2020-2025). Die Frage ist wie hoch ist die Exposition und ist das dann eine gesundheitliche Gefahr. Diskutiert werden Mechanismen, die helfen richtig und genau zu messen, z.B. Prozesskontrollen oder Referenzmaterialien. Es wird ein Weg zu mehr Harmonisierung im Bereich der Mikroplastik-Analytik aufgezeigt. T2 - Mikroplastik – Was wissen wir heute? BfR-Forum Verbraucherschutz CY - Berlin, Germany DA - 02.12.2025 KW - Microplastics KW - Reference materials KW - Harmonisation PY - 2025 AN - OPUS4-65330 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Results of the Plastic in the environment comparative test N2 - The talk describes the sturcture and the results of the "plastics in the environment" comparative test of 2019. T2 - Symposium "Challenges of microplastic analysis – Bridging state of the art and policy needs” CY - Online meeting DA - 09.09.2021 KW - Microplastic KW - Comparative test KW - ILC PY - 2021 AN - OPUS4-53236 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Identification and Quantification of Microplastic in Sewage systems by TED-GC-MS N2 - The number of publications reporting the amount of microplastic (MP) all over the world increased rapidly. Methods used so far are very time consuming and not able to provide information on total contents. As harmonised sampling, sample preparation and analysis strategies are missing different studies can hardly be compared and quantitative data, including identification and mass contents of the polymers found, are missing. This leads to a lack of comprehensive understanding of MP occurrence, source and entry pathways into the environment. We developed a method, Thermal Extraction/Desorption-Gaschromatography-Massspectrometry, as a fast screening method for MP analysis. Solid residues of water samples are heated up to 600 C under a N2 atmosphere without any sample preparation. The collected decomposition gases are separated in a gas chromatography system and detected in a mass spectrometer. Mass contents of the identified polymers can be calculated. In this presentation we will show first results from the influent of the wastewater treatment plant Kaiserslautern (Germany) and its combined sewage system as possibly entry pathway. In order to determine the relevance of wastewater split streams analysis of grey water will be conducted. Samples are fractionally filtered by a sieve cascade with mesh sizes of 500, 100, 50 µm. T2 - CEST2019 CY - Rhodos, Greece DA - 04.09.2019 KW - Microplastic KW - TED-GC-MS KW - Microplastic analysis KW - Grey water KW - Waste water treatment plant PY - 2019 AN - OPUS4-48933 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Update – Milling and weathering of granules N2 - The talk aims to describe the production of microplastic particles as test material and the additional weathering for aged particles. T2 - PlasticsFate meeting CY - Online meeting DA - 12.11.2021 KW - Microplastic KW - Cryo milling KW - Aged particles PY - 2021 AN - OPUS4-53737 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Herausforderungen bei der Mikroplastik-Analyse: Probennahme, Probenvorbereitung und Analyse N2 - Seit einigen Jahren wird in den Medien viel über das Thema Mikroplastik (MP) diskutiert. Dabei wird häufig von einer großen Anzahl an MP-Partikeln in allen Bereichen der Umwelt, wie dem Wasser, dem Boden, der Luft und in Biota sowie über mögliche Gefahren ausgehend von MP, berichtet. Jedoch sind diese Studien häufig nicht untereinander vergleichbar, da verschiedene Konzepte der Probennahme, der Aufbereitung und unterschiedliche Detektionsverfahren verwendet werden. Um diesen Mangel an vergleichbaren und aussagekräftigen Daten zu beheben, wird aktuell versucht, eine Harmonisierung der Mikroplastikanalytik voranzutreiben. Neue, schnellere Methoden zur MP Quantifizierung wurden entwickelt. Gleichzeitig werden neue Strategien zur Probenahme und Probenvorbereitung konzipiert, da hier die Fehlerquellen besonders große Auswirkungen auf das Ergebnis haben. In diesem Vortrag werden verschiedene Verfahren bezogen auf Probennahme, -vorbereitung und Analytik gezeigt und bezüglich ihres möglichen Ergebnisses diskutiert. T2 - 7. Workshop Technologieplattform Mikroverkapselung - Bioabbaubare Mikropartikel und Mikrokapseln CY - Bremen, Germany DA - 24.10.2019 KW - Mikroplastik KW - Analytik PY - 2019 AN - OPUS4-49395 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Overview of CUSP and PlasticTrace N2 - The presentation summarises the work of CUSP and PlasticTrace EU joint research projects of the last year. T2 - Microplastics Scientific Workshop of PlasticsEurope CY - Amsterdam, The Netherlands DA - 08.05.2023 KW - Microplastics KW - Microplastics standardisation KW - Reference materials KW - Polymer 3R PY - 2023 AN - OPUS4-57460 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -