TY - CONF A1 - Müller, U. A1 - Miccoli, Lorenzo A1 - Fontana, Patrick T1 - Ein Kalkeinpressmörtel für die Instandsetzung von Lehmbauten N2 - Die Instandsetzung von Lehmbauwerken ist keine einfache Aufgabe. Der Baustoff Lehm hat vergleichsweise schwache mechanische Eigenschaften. Er ist außerdem anfällig gegenüber eindringendem Wasser, wobei er sehr schnell seinen Zusammenhalt verlieren kann, wenn gewisse Feuchtegehalte überschritten werden. Instandsetzungskonzepte für Bauwerke aus solchen Materialien stellen deshalb eine Herausforderung dar. Historische Lehmbauwerke zeigen oft Schäden in Form von starker Rissbildung, die durch statische oder dynamische Lasten hervorgerufen sein kann. Häufig werden solche Risse wegen mangelnder Fachkenntnis und / oder fehlender Techniken nur ungenügend instandgesetzt. Die Rissinstandsetzung mit Einpressmörteln birgt insbesondere für Lehmbaustoffe eine Herausforderung und erfordert spezifische Anforderungen an den Einpressmörtel, wie z. B. niedriger Wassergehalt, gutes Wasserrückhaltevermögen, niedriges Schwindmaß, an das instandzusetzende Material angepasste Festigkeit und E-Modul sowie eine gute Haftung am Lehmuntergrund. Zusätzlich müssen Einpressmörtel eine ausreichende Fließfähigkeit aufweisen, um kleine Risse und Hohlräume ohne Entmischung zu füllen. Deshalb muss das rheologische Verhalten des Einpressmörtels gut untersucht und kontrolliert werden, um die gewünschte Wirkung zu erzielen. Die Rissinstandsetzung bei Lehmbauwerken erfolgt traditionell durch manuelles Stopfen mit einem Mörtel. Natürlich können auf diese Weise nur Risse mit einer großen Breite verfüllt werden. Ein weiterer Nachteil ist, dass Risse, die durch dickere Wände verlaufen, nicht vollständig mit den für das Stopfen verwendeten Werkzeugen erreicht werden können. Kalkgebundene Einpressmörtel für Lehmbaustoffe werden gewöhnlich für die Wiederbefestigung von Putzen und weniger aus statisch-konstruktiven Gründen eingesetzt Aufgrund der Eigenschaften von Lehm, müssen Einpressmörtel auf Basis von hydraulischem Kalk nach EN 459-1 wesentliche Anforderungen an eine Reihe von Eigenschaften erfüllen, die sich auf die Verträglichkeit, die Dauerhaftigkeit und insbesondere die Injektionsfähigkeit beziehen. Das Ziel der vorgestellten Untersuchungen war einen Einpressmörtel zu herzustellen, mit dem die strukturelle Kontinuität in Lehmmauerwerk oder anderen massiven Lehmwänden (Stampf- und Wellerlehm) durch Rissverpressung wiederhergestellt werden kann. Das Material bestand aus Kalkhydrat mit Zusätzen von Puzzolanen und Kalksteinfüller. T2 - Lehm 2016 - 7. Internationale Fachtagung für Lehmbau CY - Weimar, Germany DA - 12.11.2016 KW - Baustoffe KW - Einpressmörtel KW - Kalkhydrat KW - Lehmbau KW - Instandsetzung KW - Historische Bauwerke PY - 2016 SP - 1 EP - 10 PB - Eigenverlag Dachverband Lehm e. V. CY - Weimar AN - OPUS4-38824 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, U. A1 - Miccoli, Lorenzo A1 - Fontana, Patrick T1 - A lime-based grouting material for the repair of earthen structures N2 - The repair of earthen structures is not an easy task. Earth as a construction material has comparatively weak mechanical properties. It is also susceptible towards liquid water, were it can lose cohesion very quickly if certain moisture contents are exceeded. Repair concepts of structures built with such materials are therefore challenging. Historical earthen structures often exhibit damages in form of extensive cracking, which may have been caused by static or dynamic loads. Frequently these cracks are insufficiently or inappropriately repaired because of lack of knowledge and / or technology. In particular, the behaviour of crack repair by grouting poses a challenge in earthen materials and demands specific requirements for the grouting mortar, such as low water content, good water retention, low shrinkage. Grouting materials require additional specifications such as compatible strengths and Young’s modulus as well as good adhesion to the earthen substrates. In addition, grouts have to be sufficiently flowable to fill small cracks and voids without segregation or bleeding. Therefore, the rheological behaviour has to be well understood and controlled to gain the desired effects. The repair of cracks in earthen buildings is traditionally done by stuffing manually mortar into the gap. Naturally, this method is only usable for cracks with large widths. Another disadvantage is that cracks going through thicker walls cannot be completely reached by the tools used for stuffing the mortar into the crack. Lime based grouts for earthen materials were usually used for re-attachment of plasters but less for structural reasons. Due to the nature of earthen materials grouts based on formulated or hydraulic lime (according to the definition in EN 459-1) have to meet considerable demands on a variety of properties, which are related to compatibility, durability and in particular to the ability of being injected. The goal of this study was to create a grout, which can be used to re-establish structural continuity in cracked earthen masonry or other massive earth walls (rammed earth and cob) with the focus on grouting cracks. The grout material was based on hydrated lime (calcium hydroxide) with additions of pozzolana and lime stone filler. T2 - Lehm 2016 - 7th International Conference on Building with Earth CY - Weimar, Germany DA - 12.11.2016 KW - Building Materials KW - Grout mortar KW - Hydraulic lime KW - Earth construction KW - Repair KW - Historical buildings PY - 2016 SP - 1 EP - 8 PB - Eigenverlag Dachverband Lehm e. V. CY - Weimar AN - OPUS4-38825 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Steckenmesser, D. A1 - Vogel, Christian A1 - Steffens, D. T1 - P-Verfügbarkeit von Recyclingprodukten N2 - Die Pflanzenversuche der vorliegenden Arbeit zeigen sehr gut, dass das Pyrolyse Produkt der Firma Pyreg zwar in der kurzfristigen P-Verfügbarkeit nur mäßig abschnitt, dafür aber eine gute P-Nachlieferung aufweist. Dies kann maßgeblich auf die im Produkt vorliegenden P-Verbindungen zurückgeführt werden.Es zeigt sich weiterhin, dass durch eine Na2CO3-Gabe die kurzfristige Verfügbarkeit von eisengefällten Klärschlämmen verbessert werden kann, es aber keinen Einfluss auf die langfristige P-Nachlieferung hat. Das BAM-Verfahren mit Na2SO4 liefert ein Produkt, welches sowohl eine gute kurzfristige P-Verfügbarkeit, als auch eine gute langfristige P-Nachlieferung hat. Dies kann auf die dabei entstehende P-Form, CaNaPO4, zurückgeführt werden. Ferner zeigen die Experimente, dass auch schwerlösliche Phosphate mit N2-fixierendem Rotklee mobilisiert werden können. T2 - 128. VDLUFA-Kongress CY - Rostock, Germany DA - 13.09.2016 KW - Phosphor KW - Recycling KW - Düngemittel PY - 2016 SN - 978-3-941273-23-8 SP - 57 EP - 73 PB - VDLUFA-Verlag CY - Darmstadt AN - OPUS4-38906 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Paul, Andrea A1 - Heilmann, M. T. A1 - Schmid, Thomas A1 - Maiwald, Michael T1 - Multivariate classification of Raman spectra from synthetic polymers – an approach for the improved detection of microplastics N2 - The increasing pollution of terrestrial and aquatic ecosystems with plastic debris, which leads to the accumulation of microscopic plastic particles of still unknown fate, is an upcoming problem of our time. In order to monitor the degree of contamination and to understand the underlying processes of degradation and internalization of plastic debris, analytical methods are urgently needed, which help to identify and quantify microplastics. Currently, expensive collected and purified materials enriched on filters are investigated by (micro) infrared spectroscopy (FTIR). Few studies using micro-Raman spectroscopy have been published as well. In contrast to FTIR, Raman spectroscopy can handle wet samples, but it suffers from interference of fluorescent materials. Both micro-FTIR- and micro-Raman, always include time consuming scanning and mapping procedures followed by the manual inspection and measurement of selected particles. T2 - 11. Kolloquium Arbeitskreis Prozessanalytik CY - Wien, Austria DA - 30.11.2015 KW - Prozessanalytik KW - Microplastics KW - Mikroplastik KW - Raman-Spektroskopie KW - Polymers KW - Multivariate classification PY - 2015 SP - 80 EP - 81 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-38847 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jörres, R. A1 - Ehret, M. A1 - Karrasch, S. A1 - Herbig, B A1 - Schierl, R. A1 - Seeger, Stefan A1 - Langner, J. A1 - Nowak, D. T1 - Respiratorische Effekte von Drucker- und Kopierer-Emissionen – eine kontrollierte Expositionsstudie N2 - Die möglichen gesundheitlichen Auswirkungen von Laserdruckeremissionen sind immer wieder Gegenstand von Aufmerksamkeit. Wir untersuchten die Effekte 75-minütigerExpositionen gegenüber Low-Emittern (LE, Untergrund 2000 – 4000 UFP/cm3) und High-Emittern (HE, 100.000 UFP/cm3). T2 - 56. Kongress der Deutschen Gesellschaft für Pneumologie und Beatmungsmedizin e.V. CY - Berlin, Germany DA - 18.03.2015 KW - Expositionsstudie in-vivo KW - Bürogeräte KW - Emissionen KW - Partikel PY - 2015 DO - https://doi.org/10.1055/s-0035-1544873 VL - 69-V516 SP - V516 PB - Thieme CY - Stuttgart AN - OPUS4-38752 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ferraioli, M. A1 - Abruzzese, D. A1 - Miccoli, Lorenzo A1 - Mandara, A. ED - Galea, P. ED - Borg, R. P. ED - Farrugia, D. ED - Agius, M. R. ED - D'Amico, S. ED - Torpiano, A. ED - Bonello, M. T1 - Dynamic identification and seismic safety of two masonry towers N2 - The recent experience of Italian seismic events provided wide observational information about typical behaviour, damage patterns and intrinsic vulnerability of monumental buildings. Evidence indicates that historical constructions are by far the most vulnerable from the seismic point of view. As a consequence, they demand for the definition of urgent strategies for the protection of cultural heritage from seismic hazard. The main goal of an in-depth knowledge of the structure should help to avoid inadequate, unsuitable or dangerous rehabilitation operations, as well as to select non-invasive and reversible techniques for the best exploitation of material and technology features. The definition of reliable models and methods for seismic risk assessment of historical constructions is today a very important topic. Typical problems of masonry structures concern aspects like inherent structural lacks, material degradation, geotechnical problems, buckling behaviour of slender elements and dynamic loading vulnerability. Modelling the mechanical behaviour of masonry may play an important role, due to both inherent material complexity and great scatter in mechanical properties. Effective procedures for the identification of the structural parameters from static and dynamic testing are thus required. In particular, dynamic measurements may be very useful for the identification of mechanical properties and soil restraints and, consequently, for the calibration of advanced numerical finite element models. The paper addresses two case studies of structural monitoring and seismic assessment of medieval masonry towers in Italy: the bell tower of Aversa and the bell tower of Capua. These monuments, placed in the Campania region, were monitored by means of full-scale environmental vibration testing. Measured responses are then used for modal identification with a typical finite element model updating technique based on vibration test results. Parameters optimization is carried out on the basis of a criterion which minimises a weighted error on modal properties. A satisfactory improvement in the determination of modal parameters is thus obtained, resulting in a close agreement between the modal properties observed in dynamic tests and those calculated from numerical model. Seismic assessment is finally performed based on nonlinear static analysis of the tower under multimodal distributions of lateral loads. Results from nonlinear analysis indicate the potential collapse mechanisms and evidence dangerous structural weakness which may play a role in the seismic vulnerability of the towers. T2 - Georisk in the Mediterrean and their mitigation CY - Valletta, Malta DA - 20.07.2015 KW - masonry towers KW - ambient vibration tests KW - dynamic characterisation KW - seismic assessment PY - 2016 SN - 978-88-98161-20-1 SP - 250 EP - 251 PB - Mistral Service AN - OPUS4-37204 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holm, Olaf A1 - Simon, Franz-Georg T1 - Recovery of copper from small grain sizes of municipal solid waste incineration bottom ash by means of density separation N2 - Small grain sizes of municipal solid waste incineration (MSWI) bottom ash (BA) contain elemental and chemically bonded metals in appreciable amounts, especially copper. As different copper species have in general a higher density compared to the prevalent minerals, processes for density separation seemed to be favorable for the recovery of copper. Investigations with a centrifugal classifier were therefore carried out with BA from MWSI which have been used for a few years as the covering material for a landfill. The results show an appreciable enrichment of the precious copper. The concentrates contained up to 60 mg/kg copper in the dry weight (DW) (in general about 30 – 40 mg/kg DW) with enrichment factors of around 20 and a copper recovery of up to 50 % (in general around 20 %). A test series in order to evaluate the potential benefit for sequential processing illustrate the low efficiency for a further processing of the tailings. T2 - SUM 2014 - 2nd Symposium on Urban Mining CY - Bergamo, Italy DA - 19.052014 KW - Municipal solid waste incineration (MSWI) KW - Density separation KW - Bottom ash (BA) KW - Copper PY - 2014 SN - 9788862650311 SP - 1 EP - 7 PB - CISA Publisher CY - Padova, Italy AN - OPUS4-37308 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Le, Quynh Hoa A1 - Bäßler, Ralph A1 - Yevtushenko, Oleksandra A1 - Kratzig, Andreas A1 - Bettge, Dirk T1 - Synergistic effects of impurities in the condensate on the corrosion of CO2 transport pipeline N2 - For the reliability of transport pipelines the corrosion resistance of the materials used needs to be determined in conditions, which are possible during the transport process. In some situations condensation of components out of the CO2 stream can occur. To study the effect of condensate on transport pipeline steel, a “worst-case scenario” gas mixture, containing 2.5 % H2O, 1.8 % O2, 1000 ppmv NO2, and 220 ppmv SO2, was proposed, fed (1.5 L/min) into a glass reactor containing coupon-shaped specimens for 120 600 h at 278 K (to simulate the underground pipeline transport), and resulted in the condensate containing 0.114 M H2SO4 and 0.0184 M HNO3 (pH 2.13). Basing on this “original” condensate, exposure tests and electrochemical characterization together with pH and conductivity in CO2 saturated condition at the same temperature were carried out. The role of each gas impurity and the combination of them, when the condensate is formed, was studied by investigating the role of individual and varying combination of acidic components in the condensate on the corrosion behaviors of the commercial pipeline-steel (L360NB). It can be concluded that although the condensation of NOx in form of HNO3 causes faster corrosion rate, it is the condensation of SOx or the combination of SOx and NOx that may cause much more severe problems in form of localized and pitting corrosions. Different to the corrosion products formed in CO2 atmosphere without impurities (mainly iron carbonate) the corrosion products resulted from these acidic condensation have no protectability, indicating the need of controlling gas quality during the transportation within the pipeline network. T2 - EUROCORR 2017 - PRAG CY - Prague, Czech Republic DA - 03.09.2017 KW - CCUS KW - CO2 corrosion KW - Carbon steels KW - Condensate PY - 2017 SP - Paper 75636,.1 EP - 4 AN - OPUS4-41874 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miccoli, Lorenzo A1 - Müller, U. A1 - Fontana, Patrick ED - Mazzolani, F. M. ED - Lamas, A. ED - Calado, L. ED - Proenca, J. M. ED - Faggiano, B. T1 - Strengthening of rammed earth structural elements. Mechanical behaviour under shear and cyclic loading N2 - An experimental investigation was carried out to study the in-plane shear behaviour of rammed earth structural elements strengthened with polyester fabric strips. The original idea for the retrofitting with polyester fabric strips was to introduce a vertical element for walls in order to take up horizontal loads resulting in a shear response of the building element. It has to be considered that vertical slits into the walls for fixing the strips are points of weakness and have to be mitigated by the adhesive. In this case a base coat mortar was employed. Strengthened elements were tested to exploit the strength potential of earthen materials and to solve its lack of tensile strength, significantly improving not only strength but also ductility. As part of the study results of a testing campaign of unstrengthened structural elements were considered. Strengthened elements were tested in diagonal compression/shear and cyclic shear-compression. A unique reinforcement orientation was used. The results of these tests are presented in this paper and include the load-displacement behaviours, crack patterns, failure modes. The results showed that the reinforcement was the most effective under cyclic shear-compression tests, with increase in load and displacement capacity observed. Under diagonal compression the reinforcement did not likely contribute significantly to the shear resistance, due to a lack of embedment length of the strips. T2 - 3rd International Conference on Protection of Historical Constructions (PROHITECH 2017) CY - Lisbon, Portugal DA - 12.07.2017 KW - Rammed earth KW - Diagonal compression tests KW - Shear-compression tests KW - Strengthening KW - Polyester fabric strips PY - 2017 SN - 978-989-8481-58-0 SP - 157 EP - 158 PB - IST-Press AN - OPUS4-41263 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ferraioli, M. A1 - Miccoli, Lorenzo A1 - Abruzzese, D. ED - Mazzolani, F. M. ED - Lamas, A. ED - Calado, L. ED - Proenca, J. M. ED - Faggiano, B. T1 - Seismic risk assessment of the Santa Maria a Vico bell tower. Ambient vibration measurements and numerical model tuning N2 - The paper investigates the dynamic characterisation along with the numerical model tuning and the seismic risk assessment of a monumental masonry tower in Italy namely the Santa Maria a Vico bell tower. Full-scale ambient vibration tests were performed under the impact of environmental loads. The technique of modal extraction in the frequency domain was applied. In-situ investigation survey was used in calibrating the refined 3D finite element model. The FEM tuning was carried out by varying the mechanical parameters and accounting for the restraint offered by the neighbouring buildings and the role of soil–structure interaction. The paper shows that the modal identification is a reliable technique that can be used in-situ for assessing the dynamic behaviour of monumental buildings. The tuned FEM model of the tower was usefully employed to determine the theoretical fundamental frequencies, which accurately fit the experiment data. Finally, the seismic performance of the bell tower was assessed using a non-linear static procedure based on the multi-modal pushover analysis and the capacity spectrum method. The results confirm that seismic events of moderate intensity can produce heavy damage to the masonry tower presented in this study. T2 - 3rd International Conference on Protection of Historical Constructions (PROHITECH 2017) CY - Lisbon, Portugal DA - 12.07.2017 KW - Masonry tower KW - Ambient vibration tests KW - Dynamic characterisation KW - Seismic assessment PY - 2017 SN - 978-989-8481-58-0 SP - 159 EP - 160 PB - IST-Press AN - OPUS4-41279 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fontana, Patrick A1 - Qvaeschning, D. A1 - Hoppe, Johannes ED - de Schutter, G. ED - de Belie, N. ED - Janssens, A. ED - van den Bossche, N. T1 - Durability of UHPC for facade elements with self-cleaning surfaces N2 - This paper presents the development of ultra-high performance concrete (UHPC) for façade elements with self-cleaning properties. For creating self-cleaning surfaces two different approaches are proposed. One approach is based on the photocatalytic activation of the external UHPC shell by incorporation of TiO2 particles. The second approach consists of the modification of the UHPC surface by micro structuring in combination with the application of hydrophobic agents to create durable super hydrophobicity. In the framework of the H-HOUSE Project funded by the European Commission the experimental investigations were performed with UHPC based on Dyckerhoff Nanodur® technology. The special properties of this material enable the precise reproduction of any micro structure without flaws. The current results obtained from laboratory and outdoor weathering tests are promising and demonstrate the feasibility of the approaches. T2 - XIV DBMC - 14th International Conference on Durability of Building Materials and Components CY - Ghent, Belgium DA - 29.05.2017 KW - Building materials KW - Ultra-high performance concrete KW - Water repellence KW - Photocatalysis KW - Waethering KW - Durability PY - 2017 SN - 978-2-35158-159-9 VL - PRO 107 SP - 209 EP - 210 PB - RILEM Publications S.A.R.L. AN - OPUS4-40997 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sie, M. A1 - Susca, Tiziana A1 - Portal, Natalie Williams A1 - During, O. A1 - Fontana, Patrick A1 - Sjöström, C. ED - de Schutter, G. ED - de Belie, N. ED - Janssens, A. ED - van den Bossche, N. T1 - Influence of life span prediction on building component's LCA performance N2 - The life span of a building product is a key Parameter when it comes to Life Cycle Assessment (LCA) performance. Nevertheless, many uncertainties affect this parameter due to a lack of long-term performance data. The sensitivity of the LCA outcomes to this parameter has been studied within the framework of the FP7 project H-House (Healthier Life with Eco-innovative Components for Housing Constructions) funded by the European Commission. The paper Features two comparative studies conducted within the scope of this project: one for new construction and another for renovation. An innovative precast sandwich panel made of Textile Reinforced Concrete (TRC) and Foamed Concrete (FC), used for external walls in new construction, is compared with a steel reinforced concrete (SRC) wall of the same thermal resistance. For renovation, a novel halfsandwich panel made of Ultra-High-Performance-Concrete (UHPC) and Autoclaved Aerated Concrete (AAC) is compared with cladding having the same thermal performance. The Evaluation was conducted using a multi-criteria basis according to the LCA methodology (ISO 14040- 44). In each case, an identical life span for both scenarios leads to the fact that H-House components have a better environmental performance. The ISO 15686 and ist relevant parts have been considered for the estimation of the service life span. The sensitivity analysis shows the link between the impact savings of the innovative walls and the life span of the walls and their components. In particular, it was found that since both scenarios need to fulfil the same service during an identical reference period, and since some maintenance and replacement of materials are necessary over time for standard Solutions compared to the innovative ones, the chosen life span of the components plays a role of utmost importance. The sensitivity analysis discloses the effect of the assumptions on these aspects. T2 - XIV DBMC - 14th International Conference on Durability of Building Materials and Components CY - Ghent, Belgium DA - 29.05.2017 KW - LCA KW - Life span KW - TRC KW - UHPC KW - ISO 15686 PY - 2017 SN - 978-2-35158-159-9 VL - PRO 107 SP - 371 EP - 372 PB - RILEM Publications S.A.R.L. AN - OPUS4-40999 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, P. A1 - Giehl, A. A1 - Schönlein, A. A1 - Feil, F. T1 - Normenvorschlag zur Bewitterung transparenter oder transluzenter Kunststoffe N2 - Aufgrund des tieferen Eindringens der solaren Strahlung treten bei transparenten und bei transluzenten (durchscheinenden) Kunststoffen veränderte Bedingungen gegenüber opaken Proben auf. Dies kann zu speziellen Effekten und damit zu einem abweichenden Bewitterungsverhalten führen. Auch aus Mangel an geeigneten Normen werden diese Effekte häufig vernachlässigt. Deshalb initiiert der DIN-FNK auf ISO-Ebene ein entsprechendes Dokument. Die Norm ist in der Form eines Technical Reports geplant. In einem ersten Teil sollen die Besonderheiten transparenter oder transluzenter Kunststoffe erläutert werden, um den Nutzer für mögliche Probleme zu sensibilisieren. Im zweiten Teil werden Empfehlungen für Bestrahlung oder Bewitterung herausgearbeitet. In einem dritten Teil geht es dann um Besonderheiten bei der Messung von Eigenschaftsänderungen transparenter bzw. transluzenter Kunststoffe. In informativen Anhängen sollen verschiedene Beispiele die Thematik illustrieren. T2 - 51. Jahrestagung der GUS CY - Stutensee-Blankenloch, Germany DA - 29.03.2023 KW - Bewitterung KW - Polymer 3R KW - Bestrahlung KW - UV PY - 2023 SN - 978-3-9818507-8-9 SP - 39 EP - 46 PB - Gesellschaft für Umweltsimulation e.V. CY - Pfinztal (Berghausen) AN - OPUS4-57271 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schnell, A. A1 - Rübner, Katrin A1 - Ihlenfeldt, Toni A1 - Vöge, M. A1 - Ludwig, H.-M. ED - Ludwig, H.-M. T1 - Leichtbetone mit Recycling-Granulaten aus Mauerwerkbruch-Ton-Mischungen N2 - Mineralische Bauabfälle stellen in den Industrienationen den größten Abfallstrom dar. Allein in Deutschland fallen jährlich mehr als 50 Mio. Tonnen Bauschutt an, der hauptsächlich aus Beton- und Mauerwerkbruch besteht. Dabei nehmen die Verwertungs- und Recyclingquoten bei den bereits etablierten herkömmlichen Einsatzgebieten für aufbereitete Bau- und Abbruchabfälle mit zunehmender Heterogenität des Materials ab. Ein höherwertiges Recycling mit dem Ziel das aufbereitete Material in hochwertigen Betonprodukten einzusetzen erfolgt heute in Deutschland lediglich im Rahmen von Pilotprojekten. So können die groben Körnungen des Betonbruchs als rezyklierte Gesteinskörnung im Beton eingesetzt werden. Besonders eingeschränkte Verwertungsmöglichkeiten liegen für Mauerwerkbruch vor, einem Gemisch aus Beton, Ziegel, Kalksandstein, Porenbeton, Mörtel, Natursteinen und anderen mineralischen Bestandteilen. Die Ursache hierfür ist neben der heterogenen Zusammensetzung des Materials auch dessen feine Kornverteilung, die durch den bei der mechanischen Aufbereitung zwangsläufig anfallenden Feinkornanteil von 30 bis über 40 Prozentbedingt ist. Defizite in der Verwertung bestehen also besonders bei heterogenen feinkörnigen Gemischen. Hier müssen Ansätze gefunden werden, um eine hochwertige Wiederverwertung zu ermöglichen. Dafür ist eine möglichst gute Trennung der einzelnen Materialfraktionen ein bewährter Ansatz. Während Metalle mittels Band- und Wirbelstromabscheidern und leichte Fremdbestandteile über Windsichtung und Dichtesortierung ausgetragen werden können, ist eine Trennung der Materialien Ziegel, Mörtel und Beton, insbesondere für die feinen Fraktionen, derzeit technologisch und wirtschaftlich nicht umsetzbar. Ein rohstoffliches Recycling dieser heterogen zusammengesetzten Abfälle unter Nutzung ihrer chemisch-mineralogischen Zusammensetzung ohne eine vorherige Trennung in die einzelnen Materialfraktionen bietet sich als Alternative an. Ergebnisse zur Herstellung von Leichtgranulaten aus Mauerwerkbruch und Tonen in einem thermischen Prozess ähnlich der Blähtonherstellung wurden bereits mehrfach veröffentlicht. Diese Recycling-Granulate (RCG) sollen unter anderem als leichte Gesteinskörnung für Betone verwendet werden. Gegenstand dieses Beitrags sind Ergebnisse aus dem Verbundforschungsprojekt „RC-Leichtgranulate“ zum Einsatz der RCG in Leichtbeton. T2 - ibausil 2018 - 20. Internationale Baustofftagung CY - Weimar, Germany DA - 12.09.2918 KW - Recycling KW - Mauerwerkbruch KW - Leichte Gesteinskörnungen KW - Recyclinggranulat KW - Leichtbeton KW - Ton PY - 2018 SN - 978-3-00-059950-7 VL - 2 SP - 2-381 EP - 2-388 PB - F.A. Finger-Institut für Baustoffkunde CY - Weimar AN - OPUS4-46697 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rübner, Katrin A1 - Schnell, A. A1 - Ihlenfeldt, Toni A1 - Vöge, M. ED - Martins, I. M. ED - Ulsen, C. ED - Villagran, Y. T1 - Lightweight concrete with recycling aggregates made from masonry rubble and rubble-clay mixtures N2 - Structural lightweight concrete is a construction material composed primarily of lightweight aggregates (LWA), cement and water. Most LWA are produced by thermal treatment of natural raw materials such as clay and shale today. In addition to the high energy costs thereby incurred, the availability of suitable raw materials is limited. An alternative is the use of recycling LWA made from mineral construction and demolition waste. Recycling LWA made from masonry rubble and rubble-clay mixtures were studied in two different research projects. The technology pursues the idea of feedstock recycling, which means the recycling is based on the chemical and mineralogical composition of the masonry rubble and clay. The recycling LWA are produced in a multistage manufacturing process by thermal hardening in laboratory and pilot scale. Their particle bulk densities and particle strengths vary between 600 and 2000 kg/m³ and 1.5 and 13 MPa, respectively. Their equivalence to traditional LWA was proven in comprehensive tests of the aggregates themselves as well as the mortars and concretes made therefrom. Our contribution reports on the results of the characterization of the recycling aggregates compared to expanded clays and the studies on LWA concretes. T2 - IV International Conference Progress of Recycling in the Built Environment CY - Lisbon, Portugal DA - 11.10.2018 KW - Lightweight aggregates (LWA) KW - Recycling aggregates KW - Lightweight concrete KW - Masonry rubble KW - Recycling PY - 2018 SN - 978-2-35158-208-4 VL - 2018/PRO 124 SP - 323 EP - 331 PB - RILEM Publications S.A.R.L. CY - Paris, France AN - OPUS4-47315 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rückschloss, Jana A1 - Tochtrop, Christoph A1 - von Geibler, Justus A1 - Schlegel, Moritz-Caspar T1 - “Oh no, it’s broken!” – How product functionality limits lifespan N2 - Today a large variety of products with various features and designs are available for consumers. In addition to the main functions of a product, there are more and more additional functions, especially for electrical and electronic appliances. This means that looking for the right product may require extensive research by consumers and does not always lead to a sense of making an informed purchase decision. The wide variety of designs and functions can overwhelm consumers. This creates uncertainty and might lead to overrate products functionality and thus significantly shorten the service lifetime of appliances. Furthermore, the environmental impact of such functions is usually unclear, and can vary depending on the actual usage scenario. In this study, a survey was carried out in order to better understand consumers perceptions and experiences related to additional functions of products, with specific focus on domestic hobs, household refrigerating appliances and televisions. The results confirm the large number of additional functions and their overwhelming effect for consumers. Consumers purchase devices with more features than desired, or replaced them prematurely because an extra feature fails while the main function is still available. The findings of the study can be used to better inform consumers and support them to make environmentally sustainable purchasing decisions. T2 - 6th Product Lifetimes and the Environment Conference (PLATE2025) CY - Aalborg, Denmark DA - 02.07.2025 KW - Circular economy KW - Functionality KW - Durability KW - Purchase decision KW - Ecodesign PY - 2025 UR - https://journals.aau.dk/index.php/plate2025 SN - 97887-7642-060-4 DO - https://doi.org/10.54337/plate2025 SN - 2794-9540 SP - 666 EP - 674 AN - OPUS4-63823 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stohl, Leonie A1 - von Werder, Julia A1 - Manninger, T. T1 - Bioreceptive concrete: Greening facades on the microscale N2 - The accelerating climate crisis results in a rising demand for ecologically driven concepts. Regarding construction, this does not only include environmentally friendly materials but also the establishment of greenery in urban regions. This contribution presents the progress of two projects in which textured concrete slabs were designed to grow a stable biofilm of photosynthetic eukaryotic organisms. The greened panels represent an alternative to classic fa9ade greening with plants. Current literature suggests that the development of bioreceptive surface materials in the construction sector is difficult because there are no standardized methodological approaches for measuring said bioreceptivity. Therefore, the long-term. ahn is proposing a suitable measurement concept combining material Science and biology. Among other things, the intrinsic Substrate property pH value is expected to have a significant influence on biological colonization. In the current contribution the focus lies on the theoretical approach and design of experiment regarding this parameter. Available experimental data will be presented. T2 - 77th RILEM Annual Week and the 1st Interdisciplinary Symposium on Smart & Sustainable Infrastructures (ISSSI 2023) CY - Vancouver, Canada DA - 04.09.2023 KW - Bioreceptivity KW - Concrete KW - Surface pH measurement KW - Material characterization KW - Green Facade PY - 2023 UR - https://www.rilemweek2023.com/submissions/ SP - 1 EP - 6 AN - OPUS4-58304 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zubia Aranburu, Judith A1 - Cappella, Brunero A1 - Zabala Eguren, A. A1 - Buruaga Lamarain, L. A1 - Aginagalde Lopez, A. A1 - Bonse, Jörn A1 - Schwibbert, Karin T1 - Quantification of the adhesion force of E. coli on Ti via single-cell force spectroscopy N2 - Antibiotic resistance is a growing global problem which poses a massive threat to human health. Although human activity contributes to the acceleration of the process, bacteria have a self-driven stabilisation mechanism to protect themselves from such and other external threats: biofilm formation. Nonetheless, it is the adhesion of a single bacterial cell to a surface that triggers the formation of such network of biomolecules and microorganisms, as well as its hazardous consequences. The main objective of this work was to quantify the adhesion force of a single E. coli cell on a Ti substrate via the AFM-related single-cell force spectroscopy, with both the cell and the substrate material being of high clinical relevance. A set of 25 x 25 force displacement curves was acquired with a maximum force of 3.2 nN without dwell time, yielding a topography map and an adhesion force map that showed to be correlated. A mean adhesion force of 0.85 ± 0.175 nN was measured and the presence of cell appendages on the bacterial cell wall was verified through individual force-displacement curves. Bacterial viability was assessed after the measurements via live/dead staining. T2 - XL Congreso Anual de la Sociedad Española de Ingeniería Biomédica CASEIB 2022 CY - Valladolid, Spain DA - 23.11.2022 KW - Bacteria KW - Atomic force microscopy KW - Force distance curve PY - 2022 SN - 978-84-09-45972-8 SP - 217 EP - 220 AN - OPUS4-57039 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pittner, Andreas A1 - Rethmeier, Michael T1 - Ökologische Bilanzierung von Schmelzschweißverfahren unter Berücksichtigung vor- und nachgelagerter Prozessschritte N2 - Kleinere und mittlere Unternehmen agieren heutzutage in einem globalen Umfeld, wodurch diese zu Elementen einer komplexen Wertschöpfungskette werden. Der zunehmende Anstieg der Preise für industriell essenzielle Ressourcen, wie Primärenergie und Rohstoffe, sowie sich ausweitende klimapolitische Restriktion führen zur Notwendigkeit, die Wettbewerbsfähigkeit durch innovative und ökoeffiziente Fertigungsprozesse langfristig zu sichern. Rahmenbedingungen zu schaffen, welche die Positionierung nachhaltiger Produkte und Prozesse innerhalb globaler Wertschöpfungsketten ermöglicht, ist daher ein wesentliches Ziel der deutschen Industriepolitik. Im Rahmen dieses Beitrages werden aktuelle Forschungsarbeiten zur Bewertung der Umweltwirkungen der schweißtechnischen Fertigungskette anhand ausgewählter Schmelzschweißverfahren unter Berücksichtigung vor- sowie nachgelagerter Fertigungsschritte dargestellt. Das hierzu notwendige Element zur Analyse der Fertigungsprozesse ist die Ökobilanzierung - eine weit verbreitete und standardisierte Methode zur Abschätzung der Umweltwirkungen eines Produktes oder Prozesses. Hierbei stellt die Sachbilanzierung, d.h. die Ermittlung sämtlicher relevanter Energie- und Ressourcenverbräuche während der schweißtechnischen Fertigung, aufgrund des hohen Dokumentations-aufwandes sowie Ableitung assoziierter Wirkkategorien das größte Hindernis für eine Etablierung und Akzeptanz der Ökobilanzierung in der Praxis dar. Gleichwohl wird seitens Unternehmen, welche als Zulieferer von OEM’s agieren, die Dokumentation des fertigungsspezifischen CO2-Verbrauches gefordert. Ein weiterer Aspekt der Arbeiten beinhaltet folglich Methoden zur automatisierten Erfassung von schweißtechnischen Produktionsdaten sowie deren Nachverfolgbarkeit aufzuzeigen. Anhand unterschiedlicher Schweißverfahren werden die aus den Produktionsdaten abgeleiteten Energie- und Ressourcenverbräuche automatisiert in den relevanten Umweltwirkungen überführt. Die analysierten Schweißprozesse umfassen dabei ein breites für kmU relevantes Spektrum. Durch die softwareseitige Bereitstellung der aufgestellten Umweltprofile ist der Anwender in der Lage, Schweißprozesse unter ökologischen Aspekten zu bewerten und die effizienteste Variante zu identifizieren. T2 - DVS Congress 2020 CY - Online meeting DA - 14.09.2020 KW - Schweißverfahren KW - Ökobilanzierung PY - 2020 SN - 978-3-96144-098-6 VL - 365 SP - 1 EP - 7 PB - DVS Media CY - Düsselorf AN - OPUS4-51853 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klinge, Andrea A1 - Mönig, Julian A1 - Kalbe, Ute A1 - Richter, Matthias A1 - Horn, Wolfgang A1 - Ziegert, Christof A1 - Röhlen, Ulrich A1 - Roswag-Klinge, Eike T1 - upMIN 100 – upcycling MINeralischer Bau- und Abbruchabfälle zur Substitution natürlicher Gesteinskörnungen in Lehmbaustoffen T1 - upMIN 100 – Upcycling mineral construction and demolition debris as a substitute for natural aggregates in earth building materials N2 - Um zukünftig die Entnahme von Primärrohstoffen und die Deponierung von geeignetem Bodenaushub zu vermeiden, wurde im Forschungsvorhaben «upMIN100» der Einsatz von rezyklierten Gesteinskörnungen < 2 mm in Lehmbaustoffen untersucht. Diese Korngrößen aus Rezyklaten, die je nach Ausgangsstoffen und Produkt 5 – 70 % des fertigen Baustoffs ausmachen, waren zum Zeitpunkt des Projektstarts in den gültigen Lehmbaustoff-Normen DIN 18945 – 18948 nicht zugelassen, da diese als Zusatzstoffe nur natürliche Gesteinskörnungen nach DIN EN 12620, Mehl aus mörtelfreien Ziegeln sowie Blähperlit etc. nach DIN EN 13055-1 und als Bindemittel nur Baulehm aus natürlichen Vorkommen vorsahen. Um den Einsatz von rezyklierten Bau- und Abbruchabfällen für Lehmbaustoffe in der Norm zu ermöglichen, mussten daher die technische Durchführbarkeit, Qualitätsanforderungen an Ausgangsstoffe (z.B. Schadstoffgrenzwerte in Bezug auf Gesundheits- und Umweltverträglichkeit) sowie zulässige Anteile der Rezyklate geregelt werden. Aktuelle Sortier- und Aufbereitungsmethoden wurden im Hinblick auf die technische sowie die wirtschaftliche Machbarkeit überprüft und auf eine mögliche Optimierung untersucht. Um Fragen zur technischen Machbarkeit beantworten zu können, wurde im Vorhaben die exemplarische Entwicklung von zwei wiederverwendbaren Lehmbaustoffen (Lehmstein, Lehmputzmörtel) angestrebt, um zukünftig sowohl das Abfallaufkommen als auch die Rohstoffinanspruchnahme zu reduzieren. Zum einen sollten die Zuschläge bis zu 100% aber auch das natürliche Bindemittel Ton zu 80% – 100% substituiert werden. Der Machbarkeitsnachweis für beide Entwicklungen wurde in Form eines Prototyps mit einem Technologie-Reifegrad 4–5 (TRL 4–5) erbracht. N2 - To avoid the extraction of primary raw materials and the landfilling of suitable excavated soil in the future, the use of recycled aggregates < 2 mm in earth building materials was investigated in the “upMIN 100” research project. These grain sizes from recycled materials, which make up 5–70 % of the finished building material depending on the source materials and product, were not permitted in the applicable earth building material standards DIN 18945–18948 at the time the project started, as these only allow natural aggregates in accordance with DIN EN 12620, flour from mortarfree bricks and expanded perlite etc. as additives in accordance with DIN EN 13055-1 and only building clay from natural sources as a binder. For the use of recycled construction and demolition waste for earth building materials in the standard, the technical feasibility, quality requirements for source (e. g. limit values for harmful substances in terms of health and environmental compatibility) and permissible proportions of recyclates had to be regulated. Current sorting and processing methods were reviewed in terms of technical and economic feasibility and examined for possible optimisation. To ascertain the technical feasibility of the use of recycled construction demolition waste for earth building materials, the project developed two reusable earth building materials (earth blocks, clay plaster mortar) as examples of both waste reduction and of the use of raw materials in the future. On the one hand, up to 100 % of the aggregates and 80–100 % of the natural binder clay should be substituted. The proof of concept for both developments was provided in the form of a prototype with a technology readiness level 4–5 (TRL 4–5). T2 - Lehm 2024 Fachtagung CY - Weimar, Germany DA - 27.09.2024 KW - Recycled aggregates KW - Earthen building materials KW - Contaminants KW - Reuse KW - Resources PY - 2024 SP - 1 EP - 10 CY - Weimar AN - OPUS4-62612 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Fire Retardancy Featuring Sustainability: Food for Thought between Fake Fiction and Future N2 - Sustainability, or in other words, exploiting resources under the terms of environmental conservation for the economic welfare and prosperity continuously over time, would revolutionise the plastics industry were it to become predominant practice as a linear, fossil-fuel–based economy is switched to a carbon circular economy. Food for though is given by dint of a critical overview of the current trends and mainly by sketching our own key projects performed in the field of sustainable flame-retardant polymeric materials in the recent years. T2 - Interflam 2025 CY - London, United Kingdom DA - 30.06.2025 KW - Biocomposites KW - Sustainability KW - Renewable KW - Bio wastefibres KW - Fire Behavior PY - 2025 VL - 1 SP - 187 EP - 190 PB - Interscience Communications Ltd AN - OPUS4-63681 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nerger, Tino A1 - Neumann, Patrick P. A1 - Weller, Michael G. T1 - Drone-based Localization of Hazardous Chemicals by Passive Smart Dust N2 - We introduce a passive smart dust concept as a novel solution for environmental monitoring. Utilizing chemical reagents like colorimetric indicators and other chemosensors, these particles detect varying environmental conditions. We developed paper-based sensors that are both cost-effective and eco-friendly. In practical tests, these sensors, dispersed over a designated area, successfully identified hazardous substances by changing their color when exposed to acids or bases. This color change was remotely detectable using a drone-mounted color camera. The data thus obtained was processed through specialized software, accurately pinpointing areas of contamination. This method proves the efficacy and scalability of passive smart dust technology for real-time, environmentally sustainable remote sensing of hazardous materials T2 - 2024 IEEE International Symposium on Olfaction and Electronic Nose (ISOEN) CY - Grapevine, Texas, USA DA - 12.05.2024 KW - Indicator KW - Passive Smart Dust KW - Colorimetric Sensor KW - Drone KW - Cellulose KW - Environmental Monitoring KW - Confetti KW - Hazard Detection PY - 2024 SN - 979-8-3503-7053-9 VL - 1 SP - 1 EP - 3 PB - IEEE CY - Piscataway, NJ 08855-1331 USA AN - OPUS4-60176 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stanisavljevic, Mila A1 - Essel, S. A1 - Karbach, N. A1 - Zirzow, Johannes A1 - Hoffmann, T. A1 - Neumann, Patrick P. T1 - Performance Assessment of Methane and Carbon Dioxide Sensors for D rone Based Environmental Gas Monitoring N2 - This study evaluates the performance of methane (CH₄) and carbon dioxide (CO₂) sensors mounted on an unmanned aerial vehicle (UAV) for gas detection in open-field environments. Sensors were tested simultaneously during UAV flights over artificial gas sources, with wind data collected from two anemometers to understand plume dynamics. Field-deployed CH₄ sensors provided validation for the UAV-based measurements. The results demonstrate the sensors' effectiveness in gas detection. T2 - Sensor and Measurement Science International (SMSI) CY - Nuremberg, Germany DA - 06.05.2025 KW - UAV-based gas sensing KW - Sensor comparison KW - Methane and carbon dioxide detection PY - 2025 SN - 978-3-910600-06-5 DO - https://doi.org/10.5162/SMSI2025/B1.3 SP - 77 EP - 78 PB - AMA Service GmbH CY - Wunstorf AN - OPUS4-64038 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Kalbe, Ute A1 - Bandow, Nicole T1 - Potential use of incineration bottom ash in construction – Evaluation of environmental impact N2 - The results from a long-term lysimeter experiment with incineration bottom ash irrigated with artificial rain are reported. Whereas chloride concentration dropped significantly, the release of antimony increased during the course of the experiment as a result of aging processes. T2 - 10th International Conference on the Environmental and Technical Implications of Construction with Alternative Materials, WASCON 2018 CY - Tampere, Finland DA - 06.06.2018 KW - Leaching KW - MSWI Bottom Ash KW - Lysimeter KW - Antimony PY - 2018 SN - 978-951-758-631-3 SN - 0356-9403 SP - 108 EP - 110 AN - OPUS4-45416 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Krüger, Oliver A1 - Bandow, Nicole A1 - Geburtig, Anja ED - Reichert, Thomas T1 - Laboratory Weathering Test for Simulating the Leaching from Artificial Sporting Grounds N2 - In order to estimating the amount and kind of emissions from polymeric sporting tracks a laboratory test was developed in BAM that combines artificial weathering and subsequent batch and column tests [1, 2, 3]. The goal consisted in nvestigating a possible change of emissions into soil and groundwater of a new sporting ground as a function of ageing and egradation of the system. At various stages of the weathering, the samples were removed and subjected to especially designed column extraction tests for the solid samples. Both these extracts and the accumulated rainwater run-off of the weathering device were subjected to analytical tests of their ingredients. The overall aim of the test consisted in developing ontrollable, reproducible, and standardisable conditions and methods of investigation that would allow an estimation of the emissions in the course of outdoor application of about five years. T2 - 7th European Weathering Symposium. Natural and Artificial Ageing of Polymers CY - Naples, Italy DA - 16.09.2015 KW - artificial weathering KW - emission KW - leaching KW - sporting track KW - degradation KW - ageing KW - rubber KW - extraction PY - 2015 SN - 978-3-9816286-6-1 VL - CEES 17 SP - 195 EP - 208 PB - Thomas Würtz CY - Karlsruhe, Germany AN - OPUS4-35401 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Paul, Andrea A1 - Breitfeld, S. A1 - Sauer, Andreas A1 - Becker, Roland A1 - Kalbe, Ute A1 - Bremser, Wolfram A1 - Braun, Ulrike T1 - A Raman spectroscopic method for the monitoring of microplastics in soil N2 - Due to the increasing presence of microplastic particles (MP) in the Environment and the unknown risks arising from them, there is an urgent need for analytical methods that allow for an efficient identification and quantification of microplastics (MP), i.e. particles < 5 mm, in environmental samples. So far, mostly timeconsuming (micro) infrared or micro-Raman spectroscopic methods are applied. Here an faster alternative Approach is presented based on a Raman processspectrometer with fiber-optical probes in combination with multivariate data analysis. T2 - 12. Kolloquium Prozessanalytik CY - Berlin, Germany DA - 28.11.2016 KW - Raman spectroscopy KW - Microplastics KW - Soil KW - Chemometrics KW - PLS-DA PY - 2016 SP - P10, 59 EP - 60 AN - OPUS4-38392 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Susset, B. A1 - Bandow, Nicole T1 - Modellierung der Stofffreisetzung und des Stofftransportes aus Materialien in Sportböden auf Kunststoffbasis (Kunststoff- undKunststoffrasenbeläge) auf Sportfreianlagen als Bewertungsgrundlage für die Boden- und Grundwasserverträglichkeit N2 - Für Sportböden in Außenanlagen haben sich Kunststoffbeläge und Kunststoffrasenbeläge als extrem nutzungsoptimierte Bodenbeläge bewährt. Neben der Benutzungsqualität ist auch die Bewertung möglicher negativer Auswirkungen auf die Umwelt durch produktionsbedingt enthaltene Schadstoffe notwendig. Sportböden auf Kunststoffbasis sind durch mehrlagige Aufbauten gekennzeichnet. Schadstoffe können in den oberen Lagen in den dort als Füllstoff verwendeten Gummigranulaten vorhanden sein. Die Gesamthöhe dieser Schichten umfasst in der Regel maximal 10 cm. Inhaltsstoffe können durch Regenwasser mobilisiert und mit dem Sickerwasser in den Boden und in das Grundwasser eingetragen werden. Durch eine Kombination von Elutionstests und numerischer Modellierung kann das Mobilisierungs- und Transportpotential ermittelt werden, um eine Boden- und Grundwassergefährdungsabschätzung auf Basis einer Sickerwasserprognose vorzunehmen. Die hier vorgestellte Studie „Umweltverträglichkeit von Kunststoffbelägen auf Sportfreianlagen- Modellierung der Stofffreisetzung aus Sportböden auf Kunststoffbasis zur Bewertung der Boden- und Grundwasserverträglichkeit“befasst sich ausschließlich mit der Stofffreisetzung und den Pfad Boden-Grundwasser (Boden- und Grundwasserschutz). Der Pfad Boden-Mensch und Belange des Gesundheitsschutzes sind nicht Gegenstand dieser Untersuchungen. T2 - Fachseminar Aktuelles im Sportplatzbau CY - Hennef, Germany DA - 02.03.2017 KW - Sportböden auf Kunststoffbasis KW - Freianlagen KW - Schadstofffreisetzung KW - Stofftransport KW - Gefahrenabschätzung Pfad Boden-Grundwasser PY - 2017 SP - 1 EP - 7 AN - OPUS4-42995 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Schatten, Rene A1 - Szuppa, Tony T1 - Monitoring von Bodenmaterialien zur Einschätzung potenzieller Verwertungswege N2 - Ziel eines laufenden UFOPLAN-Vorhabens ist es, Datendefizite für Bodenmaterialien, die unter die neuen Kriterien der Verwertungsmöglichkeiten außerhalb der durchwurzelbaren Bodenschicht nach den §§ 6 bis 8 der Novelle der BBodSchV fallen, zu schließen und potenzielle Verwertungsmöglichkeiten aufzuzeigen. Neben den Feststoffwerten wird dabei das Elutionsverhalten zur Bewertung herangezogen. Durch die Umstellung des Elutionsverfahrens von einem W/F von 10 l/kg (bisherige Regelung in der LAGA M 20) auf ein W/F von 2 l/kg bestehen erhebliche Unsicherheiten im Hinblick auf die Einstufung von Bodenmaterialien zur Verwertung. Neben der Untersuchung relevanter Bodenmaterialien werden auch vorhandene Daten ausgewertet. Der Schwerpunkt der Untersuchungen wurde auf die Schadstoffgruppe der PAK gelegt. Dabei werden auch Probleme der Vergleichbarkeit verschiedener Verfahren der PAK-Analytik angesprochen. T2 - Jahrestagung der DBG 2017, Kommission V „Bewertung und Eigenschaften urbaner Böden“ CY - Göttingen, Germany DA - 02.09.2017 KW - Leaching KW - Bodenmaterialien KW - Verwertung KW - BBodSchV KW - PAK PY - 2017 UR - http://eprints.dbges.de/1261/ SP - 1 EP - 3 AN - OPUS4-42998 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Vogel, Christian A1 - Simon, Franz-Georg T1 - Antimony in incineration bottom ash – Leaching behavior and conclusions for treatment processes N2 - Antimony (Sb) is used in industrial products mainly as flame retardant in plastic material. Due to such additives in plastics, about a half of Sb ends up in municipal solid waste incineration at the end-of-life and consequently in relevant amounts in the generated bottom ash. In contact with water, the initial leachability is low, as antimonates form sparingly soluble compounds with Ca2+. Following the carbonation of the incineration bottom ash (IBA) during the proceeding ageing the pH in the leachates decreases. With decreasing concentration of Ca in the eluate the solution equilibrium changes and antimonates dissolve. In Germany it is intended to regulate Sb in IBA with the planned implementation of the so called Mantelverordnung (MantelVO, containing provisions on the utilisation of mineral waste) in the near future. The limit values set in the draft might be critical for IBA and therefore pose a risk for the utilisation of the mineral fraction of IBA in the well-established recycling routes. T2 - SUM 2020 – 5th Symposium on Urban Mining and Circular Economy CY - Online meeting DA - 18.11.2020 KW - Bottom ash KW - Leaching KW - Antimony PY - 2020 SP - 1 EP - 4 AN - OPUS4-51622 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brandt, S. A1 - Brozowski, F. A1 - Plehn, W. A1 - Horn, Wolfgang A1 - Müller, B. T1 - Further Development of Odour Testing of Building Products – Sample Presentation and Evaluation of Perceived Intensity N2 - Indoor air quality is affected by the emission of volatile organic compounds (VOC) or the odour from building products. Odours can be measured by applying the standard ISO 16000-28:2020. In the study presented here proposals for further technical development of the ISO method are presented. The sampling procedure and evaluation method of the perceived intensity are investigated in particular because they have a major influence on reproducibility of measurement results. T2 - 17th International Conference HEALTHY BUILDINGS EUROPE 2021 CY - Online meeting DA - 21.06.2021 KW - Geruchsmessung KW - Emissionen KW - Bauprodukte KW - VOC KW - Perceived Intensity PY - 2021 SN - 978-82-536-1728-2 VL - 2021 SP - 1 EP - 4 PB - SINTEF Books CY - Oslo, Norwegen AN - OPUS4-54574 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brandt, S. A1 - Brozowski, F. A1 - Horn, Wolfgang A1 - Plehn, W. A1 - Müller, B. T1 - New developments in odour testing: Adapter connects emission test chamber and funnel N2 - Healthy and energy efficient buildings must be free from disturbing odours. Odour emissions from building materials can be measured with the well-known and accepted standard ISO 16000-28 “Indoor air – Part 28: Determination of odour emissions from building products using test chambers”. For commonly used emission test chambers the sample air is collected in containers (bags) and presented to a group of panel members for the purpose of evaluating the odour. A standard sets requirements for the on-demand presentation in detail. These include the validation procedure for container materials, pre-treatment of bags, details on storage of filled bags and how to carry out the measurements. However, although these measures are proven in practice, incorrect measurements are still possible. Also errors can occur due to a very complex measurement procedure. So, there is a great need for research into how the odour samples are presented. The proposal planned to be presented will introduce a new development in sample provision by using an adapter which enables collection and provision of sample air without storage or transport of bags. The adapter is a sample container which is permanently positioned on the emission test chamber´s outlet and continuously filled with sample air flowing through it. The flow is briefly interrupted at the time when a sample is taken by a panel member for the test. The size of the container is sufficient to provide enough sample air for evaluation by at least one panel member via a funnel. Since sampling and presentation are technically connected, it means you can almost do away with storage or transportation and thus it can be presented almost unchanged to the panelmembers. The aim is to reduce measurement errors in the odour samples provision process and the improvement of measurement reproducibility. The paper presents the construction of the adapter as well as the results of emission and odour tests carried out so far. T2 - CLIMA 2022 The 14th REHVA HVAC World Congress CY - Rotterdam, The Netherlands DA - 22.05.2022 KW - Perceived Intensity KW - Emissionen KW - Geruch KW - Bauprodukte PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-556192 DO - https://doi.org/10.34641/clima.2022.168 SP - 1 EP - 5 PB - TU Delft open CY - Delft, Niederlande AN - OPUS4-55619 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brandt, S. A1 - Brozowski, F. A1 - Horn, Wolfgang A1 - Müller, B. T1 - Odour testing of building products: Examinations for an on-going development of the test standard ISO 16000-28 N2 - VOC-emissions and their odours from building products and furnishings present indoors should not have an impact on personal well-being or health. Odours can be measured by applying the standard ISO 16000-28. Indoor air determination of odour emissions from building products using test chambers. One of the described procedures is the assessment of perceived intensity using a comparative scale by a group of panellists. In this paper, the perceived intensity sampling procedure and its evaluation method are investigated and shown to need improvement. New technical developments in the methodology used to increase the reproducibility of measurement results are discussed. Since odour tests are used for labelling, they have a major influence on the assessment of construction products, similar to the procedure of the German Committee for Health Evaluation of Building Products (AgBB). In the original ISO standard, the evaluation is typically performed using a sampling container separated from the emission chamber. For a better sample presentation, an adapter was developed to connect the emission test chamber to the evaluation funnel and thus enable an odour assessment which is comparable to a direct measurement. The investigations show that losses of odourous substances can be greatly reduced, which is very desirable when seeking to obtain reliable results in odour measurement. Another experimental series was carried out to reduce the measurement effort in the evaluation of perceived intensity. Application of the developed greater than or less than/equal to. query could be helpful here. The results show that the query mostly leads to the same result as the evaluation of the perceived intensity using the method according to the standard but is much easier to perform. Overall, the results can contribute to improving the acceptance of the evaluation of perceived intensity using ISO 16000-28 and to determining odours from building materials increasingly more precisely. T2 - Healthy Buildings 2023 Europe CY - Aachen, Germany DA - 11.06.2023 KW - Building material KW - Odour KW - Perceived intensity KW - VOC KW - Emission test chamber PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-580070 SP - 345 EP - 352 PB - ISIAQ (International Society of Indoor Air Quality and Climate) CY - Herndon, VA, USA AN - OPUS4-58007 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Kohlhoff, Harald A1 - Hüllmann, Dino A1 - Lilienthal, A.J. A1 - Kluge, Martin T1 - Bringing Mobile Robot Olfaction to the Next Dimension – UAV-based Remote Sensing of Gas Clouds and Source Localization N2 - This paper introduces a novel robotic platform for aerial remote gas sensing. Spectroscopic measurement methods for remote sensing of selected gases lend themselves for use on mini-copters, which offer a number of advantages for inspection and surveillance. No direct contact with the target gas is needed and thus the influence of the aerial platform on the measured gas plume can be kept to a minimum. This allows to overcome one of the major issues with gas-sensitive mini-copters. On the other hand, remote gas sensors, most prominently Tunable Diode Laser Absorption Spectroscopy (TDLAS) sensors have been too bulky given the payload and energy restrictions of mini-copters. Here, we introduce and present the Unmanned Aerial Vehicle for Remote Gas Sensing (UAV-REGAS), which combines a novel lightweight TDLAS sensor with a 3-axis aerial stabilization gimbal for aiming on a versatile hexacopter. The proposed system can be deployed in scenarios that cannot be addressed by currently available robots and thus constitutes a significant step forward for the field of Mobile Robot Olfaction (MRO). It enables tomographic reconstruction of gas plumes and a localization of gas sources. We also present first results showing the gas sensing and aiming capabilities under realistic conditions. T2 - IEEE International Conference on Robotics and Automation (ICRA) CY - Singapore DA - 29.05.2017 KW - Tunable Diode Laser Absorption Spectroscopy (TDLAS) KW - 3-axis gimbal KW - Mobile Robot Olfaction KW - Tomographic reconstruction of gas plumes KW - Localization of gas sources KW - Aerial platform PY - 2017 SN - 978-1-5090-4632-4 SP - 3910 EP - 3916 PB - IEEE AN - OPUS4-40545 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Jann, Oliver T1 - Comparison of Formaldehyde Concentrations in Emission Test Chambers Using EN 717-1 and EN 16516 N2 - For more than 25 years EN 717-1 (Wood-based panels - Determination of formaldehyde re-lease - Part 1: Formaldehyde emission by the chamber method) is the standard for formalde-hyde emission testing of wooden boards. In 2017 EN 16516 (Construction products - Assess-ment of release of dangerous substances - Determination of emissions into indoor air) was published as a new harmonised standard for the emission testing of construction products. Because test chamber conditions are different, both standards give different concentrations for formaldehyde. To determine a conversion factor four test series were set up with different wooden boards. For a loading of 1 m²/m³ the conversion factor is 1.6. This means that the formaldehyde concentration measured under the conditions of EN 16516 is a factor of 1.6 higher compared to EN 717-1. T2 - Conference on Indoor Air CY - Philadelphia, PA, USA DA - 22.07.2018 KW - Loading factor KW - European standard KW - Construction products KW - Air exchange rate PY - 2018 SP - paper 627 AN - OPUS4-45630 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dittmann, Daniel A1 - Saal, L. A1 - Zietzschmann, F. A1 - Mai, M. A1 - Altmann, Korinna A1 - Al-Sabbagh, Dominik A1 - Ruhl, A. S. A1 - Jekel, M. A1 - Braun, U. T1 - Aktivkohlecharakterisierung als weiterer Schlüssel für Adsorptionsprognosen organischer Spurenstoffe in der vierten Reinigungsstufe N2 - In diesem Beitrag wird der Einfluss des Aktivkohleprodukts auf die Adsorption von Spurenstoffen aus Kläranlagenablauf gezeigt und diskutiert. Im zweiten Teil wird das Material Aktivkohle analytisch charakterisiert und die Eigenschaften systematisiert. Die gewonnenen Erkenntnisse werden mit Bezug zu Praxislösungen zusammengefasst. T2 - Wasser 2021 CY - Online meeting DA - 10.05.2021 KW - Aktivkohle KW - Thermogravimetrie KW - Zersetzungsgasanalyse KW - Proximatanalyse PY - 2021 SP - 373 EP - 378 AN - OPUS4-52740 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seher, Julia A1 - Rübner, Katrin A1 - Müller, Constanze A1 - Martin, F. A1 - Pniok, N. A1 - Dreisow, B. ED - Döring, I. ED - Villagran Zaccardi, Y. ED - Müller, A. T1 - Lightweight aggregates made from construction and demolition waste - Application in lightweight concrete and mortars N2 - Heterogeneous construction and demolition waste can be used as raw material to produce lightweight aggregates (LWA) similar to expanded clays. In the joint research project “REALight”, LWA were produced from masonry rubble in a thermal expanding process using a pilot production plant with a rotary kiln. Our research focuses on the characterisation of the novel LWA and their use in different hydraulically bound applications. Infra-lightweight concrete (ILC) was produced with the novel LWA, which accounts for two thirds of total aggregate volume, and Celitement, which is a hydraulic binder with a low carbon footprint. Its dry bulk density is ≤ 800 kg/m³. Strength and durability properties are comparable to ILC data from the literature. Lime-based repair mortars (LRM) containing LWA are beneficial for sandstone conservation due to their similar properties regarding porosity, water absorption and strength. A two-layer repair mortar system, which consists of a filling mortar to fill large voids and a covering mortar to modulate the surface texture to the historic sandstone, was developed. In our contribution, we present results of the LWA characterisation according to the European standard EN 13055:2016. Requirements and challenges of the use of the novel LWA in ILC and LRM are discussed. T2 - V International Conference Progress of Recycling in the Built Environment CY - Weimar, Germany DA - 10.10.2023 KW - CDW recycling KW - Lightweight aggreagtes KW - Lightweight concrete KW - Masonry rubble KW - Repair mortar PY - 2023 SN - 978-2-35158-238-1 VL - PRO 137 SP - 85 EP - 92 PB - RILEM Publications S.A.R.L. CY - Champs-sur-Marne, Frankreich AN - OPUS4-58991 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lörchner, Dominique A1 - Koch, Matthias A1 - Kroh, L. W. A1 - Köppen, Robert T1 - Photodegradation of the „novel“ brominated flame retardant tris-(2,4,6-tribromophenoxy)-s-triazine N2 - Brominated flame retardants (BFRs) comprise a class of structurally diverse compounds that are functionally related and used in materials to reduce the flammability of polymers. Due to their global distribution, potential persistence, bioaccumulation and toxicity most of the BFRs of the first Generation are banned or restricted, and replaced by new ones. However, based on similar properties these new compounds may also pose a serious risk by causing adverse effects to human health and the environment. These alternative BFRs were grouped into two classes: „novel” and „emerging” BFRs. Emerging BFRs are defined as compounds that have been identified in any environmental compartments whereas novel BFRs are only detected in materials and/or goods above 0.1 wt.-%. The environmental fate of these alternative BFRs is partially unknown. Over the past years a multitude of studies on the photodegradation of BFRs in environmental matrices have been conducted to assess the photochemical behavior and fate in the environment. The photolytic debromination reaction is particularly induced among BFRs by UV exposure. The novel brominated triazine-based flame retardant tris-(2,4,6-tribromophenoxy)-s-triazine (TTBPTAZ) (Table 1) is a BFR that is mainly used in acrylonitrile butadiene styrene and high impact polystyrene. Ballesteros-Gómez et al. detected TTBP-TAZ in 8 of 13 plastic parts of consumer products and in 9 of 17 indoor dust samples but the photochemical behavior and fate is not known until now. The results of the present study, focused on photodegradation processes were performed for the first time for TTBP-TAZ to identify the photolysis intermediates and products to assess the environmental fate. T2 - DIOXIN CY - Florence, Italy DA - 29.08.2016 KW - Brominated flame retardants KW - TTBP-TAZ KW - Photodegradation PY - 2016 VL - 78 SP - 699 EP - 702 CY - Bayreuth AN - OPUS4-39037 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rudy ED - Robinson, W. H. T1 - “From Saul to Paul” - Urban Pests in Cultural Entomology N2 - Harmful insects like clothes moths and termites occurring in the synanthropic environment are considered pests which need to be controlled. However, human culture has also always widely utilized them as central characters in philosophy, in classic and modern world literature, in music and arts, and much more. This article will highlight some recent exploitations of pest insects in Cultural Entomology. It will provide examples of pieces of art and ephemeral displays with clothes moths and termites as protagonists. The insects´ destructive nature on textiles or wood was turned around to a process of creation with aesthetic, philosophical and metaphoric messages, or simply for unique ways of entertainment. References will be provided to milestones of pest insect use in Cultural Entomology. T2 - International Conference on Urban Pests (ICUP) CY - Lund, Schweden DA - 29.06.2025 KW - Termites KW - Cultural Entomology KW - Material pests KW - Performance art KW - Tineola bisselliella PY - 2025 SP - 298 EP - 304 AN - OPUS4-64639 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Elert, Anna Maria A1 - Meyer, Lena A1 - Brunner, Nanine A1 - Melzer, Micheal A1 - Koch, Claudia T1 - Advancing Digital Quality Infrastructure: Transforming Laboratory Processes for Enhanced Efficiency and Reliability N2 - The digital Quality Infrastructure (QI) holds significant potential for ensuring and enhancing the accuracy, reliability, and efficiency of laboratory processes. Establishing digital QI tools and processes and the integration into the larger digital QI ecosystem however comes with many technical and organizational challenges at the laboratory but also larger system level. This paper presents solutions of a digital QI tool set that are being developed within the German initiative QI-Digital, our own experiences in the implementation of Digital Calibration Certificates (DCCs) as eAttestation in our laboratory, as well as the structured process we have been establishing to engage with the laboratory community to support adoption of the digital QI. T2 - 2025 IMEKO TC-6 International Conference of Metrology and Digital Transformation - M4DConf CY - Benevento, Italy DA - 03.09.2025 KW - Digital Calibration Certificate KW - Digitalization KW - Laboratories KW - Quality Inflastructure PY - 2025 VL - 2025 SP - 1 EP - 6 AN - OPUS4-64283 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meyer, Lena A1 - Elert, Anna Maria A1 - Koch, Claudia T1 - A digital Quality Infrastructure for testing and calibration laboratories: from theory to practice N2 - The digital Quality Infrastructure (QI) offers significant potential to enhance the technical excellence and efficiency of laboratory operations. By leveraging tools and processes of a digital QI laboratories, their customers, authorities and other stakeholders can enhance efficiency foster trust and generate added value. This paper introduces the digital QI toolset and ecosystem as developed in the German initiative QI Digital, and explores concrete Scenarios for their implementation in laboratories Successful rollout not only requires technical development but also intense stakeholder engagement . Consequently, this paper shares insights and outcomes from a structured stakeholder dialogue with the laboratory community, and outlines the establishment of the digital LabHub' as a pivotal step to drive digital transformation and facilitate the widespread Adoption of digital QI within laboratories and their broader ecosystem. T2 - 2025 IMEKO Joint Conference TC8 -TC11 - TC24 CY - Turin, Italy DA - 14.09.2025 KW - Quality Infrastructure KW - Digitalization KW - Laboratories PY - 2025 SP - 1 EP - 6 AN - OPUS4-64282 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Monavari, Mehran A1 - Prellwitz, Matthias A1 - Koch, Claudia A1 - van de Kreeke, Johannes A1 - Melzer, Michael A1 - Richter, Silke T1 - The Digital Reference Material Document: From Paper Certificates to Interoperable Data Objects in Digital Quality Infrastructure N2 - Reference materials (RMs) are essential for traceable and reliable measurements in science and industry, yet their certificate/document remain largely paper-based. The Digital Reference Material Document (DRMD) project at BAM introduces a transformative approach by converting traditional RM certificates/documents into machine-interpretable, XML-based digital assets. Building on the Digital Calibration Certificate framework, DRMDs encode ISO 33401 requirements and integrate semantic standards like D-SI and material identifiers. These digital documents support automated data exchange, integration into laboratory systems, and interoperability e.g. via asset administration shells and data spaces. The paper presents the DRMD schema concept, and outlines the path toward international harmonization and large-scale deployment, positioning DRMDs as a cornerstone of a digital quality infrastructure. T2 - IMEKO TC-6 International Conference on Metrology and Digital Transformation - M4DConf 2025 DA - 03.09.2025 KW - Digital Reference Material Document KW - Quality Infrastructure KW - Reference Material Certificate KW - DRMD PY - 2025 UR - https://www.m4dconf.org/ UR - https://www.sciencedirect.com/journal/measurement-digitalization SP - 1 EP - 6 AN - OPUS4-64269 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cornelsen Sampaio Kling, I. A1 - Pauw, Brian Richard A1 - Agudo Jácome, Leonardo A1 - Archanjo, B. S. A1 - Simão, R. A. T1 - Development and characterization of starch film and the incorporation of silver nanoparticles N2 - Starch is one of the biopolymers being used for bioplastic synthesis. For production, starch can be combined with different plasticizers, starches from different plant sources and even with nanomaterials to improve or to add film properties. The challenge of adding these, e.g. in the form of silver nanoparticles (AgNp) is to determine the concentration so as to avoid impairing the properties of the film, agglomeration or altering the visual characteristics of the film. In this study, a starch film synthesis route and the incorporation of silver nanoparticles has been proposed in order not to alter the properties of the film while maintaining the transparency and a clear colour of the starch film. The results showed that the proposed synthesis route is promising, efficient, reproducible, fast and the film has good mechanical properties. T2 - Semana MetalMat & Painal PEMM 2020 CY - Online meeting DA - 23.11.2020 KW - Biofilm KW - Silver nanoparticle KW - Starch KW - Starch nanoparticle PY - 2020 SP - 1 EP - 2 AN - OPUS4-51940 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Winkler, Nicolas P. A1 - Neumann, Patrick P. A1 - Schaffernicht, E. A1 - Lilienthal, A. J. T1 - Heterogeneous Sensor Networks: Challenges and Insights from an Industrial Scenario N2 - Monitoring airborne pollutants is critical for occupational health, particularly in industrial environments where workers are exposed to hazardous emissions. Traditional measurements are typically limited to single-day campaigns, resulting in extremely sparse temporal data. Low-cost sensor networks offer a way to increase spatial and temporal resolution but are limited by issues of accuracy and reliability. To address this, we present a wireless heterogeneous sensor network that integrates low-cost stationary nodes with high-quality sensors on mobile platforms, including ground and aerial robots. We deploy this system in a hot rolling mill facility and evaluate its performance under real-world conditions. Field experiments reveal dynamic pollutant patterns, such as altitude-dependent PM2.5 gradients and temperature fluctuations. By introducing synchronized “rendezvous” events between mobile and stationary nodes, we demonstrate correlation capabilities of sensors. Our spatiotemporal analysis shows that, despite limitations of mobile sensing, strategically combining heterogeneous data sources enables capturing pollutant dynamics in complex industrial settings. T2 - IEEE SENSORS 2025 CY - Vancouver, BC, Kanada DA - 19.10.2025 KW - Environmental monitoring KW - Sensor data fusion KW - Sensor system networks KW - Mobile robotics PY - 2025 SN - 979-8-3315-4467-6 SP - 1 EP - 4 PB - IEEE CY - Piscataway, NJ, USA AN - OPUS4-64501 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - An, Biwen Annie A1 - Kunte, Hans-Jörg A1 - Koerdt, Andrea ED - Eibergen, N. ED - Poulassichidis, T. T1 - Microbiologically Influenced Corrosion (MIC) by Halophilic (Salt-Loving) Nitrate and Sulfate-Reducing Microorganisms N2 - The survey of Canadian shale sites showed a dominance of halophilic microorganisms, including Halomonas (HA). Nitrate-amended incubations of the field samples under high salinity (14.6% NaCl), revealed a dominance of HA (>72%) and an accumulation of nitrite. Nitrite accumulation directly inhibited the growth of SRB, thereby decreasing their souring and corrosion risks. However, accumulated nitrite may also contribute to iron corrosion, which will be tested by using different concentrations of nitrate as an electron acceptor to HA. Different salinities are further tested on HA strains supplemented with iron coupons to determine their effects on iron corrosion rates. HA incubated with separate cultures of corrosive methanogen and SRB were tested to determine whether a positive or adverse effect will occur between them. Lastly, analyses of iron coupons will be conducted using TOF-SIMS, FIB-SEM and EDS for corrosion product characterization T2 - Corrosion 2021 CY - Online Meeting DA - 19.04.2021 KW - MIC KW - Bacteria KW - Halophile KW - Corrosion KW - Environmental condition KW - Korrosion KW - High salinity PY - 2021 UR - https://my.nace.org/PaperTrail/Authors/Submission.aspx?id=2914f145-7f8f-ea11-813a-005056a95a7c SP - Paper C2021-16284, 1 AN - OPUS4-52479 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea A1 - An, Biwen Annie A1 - Deland, Eric ED - Eibergen, N. ED - Poulassichidis, T. T1 - Novel Multiport Flow-Column Corrosion Monitoring System (MFC) Revealed High Corrosion Rates by Corrosive Methanogenic Archaea N2 - MFC was used to study the corrosiveness of iron-utilizing methanogen, Methanobacterium IM1 under flow conditions. Comparing against electrical SRM, Desulfovibrio ferrophilus IS5, results showed under standard mesophilic conditions, average corrosion rates of Methanobacterium IM1 was double that of SRM. The highest corrosion rate of Methanobacterium IM1 reached up to 0.60 mm/yr under neutral conditions, and severe pitting was observed on the iron surface. Furthermore, the corrosion products of Methanobacterium IM1 were characterized with TOF-SIM, FIB-SEM and EDX, and preliminary results revealed FeCO3 is not the only corrosion product of Mi-MIC, as previously reported. Under low pH conditions, the maximum corrosion rate of Methanobacterium IM1 reached 1.57 mm/yr, which resulted in severed deformity of the iron specimen. Additional comparisons using different types of incubation material were conducted to standardize MFC MIC testing. T2 - Corrosion 2021 CY - Online Meeting DA - 19.04.2021 KW - MIC KW - Microbiologically influenced corrosion KW - Biocorrosion KW - Hi-Tension KW - Environmental condition KW - Flow Model KW - Modelling KW - Korrosion PY - 2021 UR - https://my.nace.org/PaperTrail/Authors/Submission.aspx?id=2b6387be-7390-ea11-813a-005056a95a7c SP - Paper C2021-16303, 1 AN - OPUS4-52480 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Winkler, Nicolas P. A1 - Nerger, Tino A1 - Lohrke, Heiko A1 - Bartholmai, Matthias T1 - Robotic Olfaction in Action: Field Applications and Results from Current Research N2 - In recent decades, robotics, particularly in environmental monitoring, has made significant advances. Robots of various forms and sizes have become essential tools for data collection in environmental research. Mobile Robot Olfaction (MRO) involves mobile robots equipped with gas sensors and requires the integration of multiple disciplines, including signal processing, machine perception, autonomous navigation, and pattern recognition. Common applications of MRO include mapping gas distributions, locating and detecting gas sources, and tracking gas plumes. Aerial Robot Olfaction (ARO) is a specialized branch of MRO that adapts these concepts to aerial robots, addressing the challenges of airborne gas sensing. This presentation highlights recent developments and results from ongoing research projects in MRO and ARO, with a focus on real-world deployment scenarios and the challenges encountered in practice. T2 - Drohnen in der Zerstörungsfreien Prüfung CY - Magdeburg, Germany DA - 26.11.2025 KW - Ground and Aerial robots KW - Gas distribution mapping KW - Gas source localization KW - Gas Tomography KW - Mobile Robotic Olfaction PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-648928 UR - https://www.ndt.net SP - 1 EP - 15 PB - DGZfP AN - OPUS4-64892 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klaus, Christian A1 - Soruco Aloisio, Ricardo A1 - Koch, Claudia A1 - Prellwitz, Matthias T1 - Towards Safety and Accuracy of Hydrogen Refuelling Stations through Digital Twins N2 - This paper presents digital quality infrastructure methods for hydrogen refueling stations using the Asset Administration Shell as a standardized digital twin. Implemented at BAM’s test platform, it integrates real-time sensor data, calibration certificates, and compliance documents to support traceable, interoperable asset management. In combination with AI and semantic tools, the system will enable predictive maintenance, remote audits, and improved safety. This approach reduces downtime, enhances transparency, and offers a scalable model demonstrating the potential of digital twins in advancing metrological traceability and operational efficiency in hydrogen technologies. T2 - IMEKO TC-6 International Conference on Metrology and Digital Transformation - M4DConf 2025 CY - Benevento, Italy DA - 03.09.2025 KW - Datenintregration KW - IT KW - Verwaltungsschale KW - Infrastruktur KW - OT KW - Open Source KW - Software PY - 2025 UR - https://www.m4dconf.org/ UR - https://www.sciencedirect.com/journal/measurement-digitalization SP - 1 EP - 6 AN - OPUS4-64951 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Le, Quynh Hoa A1 - Bäßler, Ralph A1 - Kratzig, Andreas A1 - Bettge, Dirk A1 - Kranzmann, Axel A1 - Knauer, S. T1 - Droplet corrosion of CO2 transport pipeline steels N2 - In this work, the focus was set on the corrosion process of condensate as drops on the surface of carbon steels (X52, X70), martensitic steel UNS S41500, and superaustenite UNS N08031 in CO2 atmosphere with impurities at 278 K (to simulate the transportation condition in a buried pipeline). Exposure tests were performed at both normal pressure and high pressure where CO2 is supercritical or in dense phase. The drop, 1 ‑ 10 μL in volume, was prepared by dropping CO2 saturated ultra-pure water onto the surface of steel coupons in a one-liter-autoclave. The CO2 gas stream, simulating the oxyfuel flue gas with varying concentration of impurities (SO2 and O2 ), was then pumped into the autoclave to observe the condensation and corrosion impacts of impurities. Comparable exposure tests were carried out with the same gas mixture and the same volume of water as vapor to observe the drop formation and the corrosion process that follows. The wettability and stability of drops on the surface of steel coupons in CO2 supercritical/dense phase environment was evaluated additionally by contact angle measurement. T2 - NACE International Annual Corrosion Conference CY - Phoenix, AZ, USA DA - 15.04.2018 KW - Geothermal KW - Coating KW - SiO2 KW - Polyaniline KW - Corrosion PY - 2018 SP - 10845, 1 EP - 11 PB - Omnipress CY - Houston AN - OPUS4-44917 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Le, Quynh Hoa A1 - Yevtushenko, Oleksandra A1 - Bettge, Dirk T1 - Corrosion Aspects for Materials to be Used in CC(U)S Applications N2 - This contribution provides current findings regarding materials susceptibility for carbon capture, utilization and storage (CCUS) applications. Basing on results gathered in 2 German long-term projects (COORAL and CLUSTER) suitable materials are introduced as well as dominating impurities of the CO2-stream and corrosion mechanisms. Investigations cover the whole CCUS process chain and provide material recommendations for certain parts. T2 - 1st International Conference on Corrosion Protection and Application CY - Chongqing, China DA - 09.10.2019 KW - Carbon KW - Capture KW - Storage KW - Utilization KW - CCS KW - CCU KW - CO2 KW - Corrosion KW - Steel PY - 2019 SP - Paper 31 PB - Chinese Society for Corrosion and Protection CY - Chongqing/China AN - OPUS4-49301 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Priebe, Nsesheye Susan A1 - Schmidt, Wolfram A1 - Rogge, Andreas A1 - Kühne, Hans-Carsten ED - Schmidt, Wolfram ED - Priebe, Nsesheye Susan T1 - Optimising available resources for production of good concrete properties N2 - There is a wide range of research worldwide on supplementary cementitious materials (SCMs) such as fly ash and slag for substituting pure cement. Such materials are suitable to be considered in a cementitious system with ordinary Portland cement (OPC) due to their high pozzolanic properties. In addition, majority of the SCMs are said to significantly improve concrete properties especially in terms of increased strength and durability. Unfortunately, the production of such SCMs is not entirely eco-friendly and also limited to certain parts of the world, hence one has to look at alternative options. The issue of availability of resources is a strong concept that is ever-increasing, and the use of more eco-friendly SCMs in a cementitious system is furthermore attractive. Hence this paper addresses the use of eco-friendly SCMs in concrete such as rice husk ash (RHA). Despite the fact that extensive research has been done on this material, its application in a cementitious system to obtain sufficient concrete properties is still rather limited. In a country like Tanzania, high strength concrete construction is applicable in special construction cases but certainly not a high priority. Majority of construction is still undertaken using normal strength concrete. In a ternary cementitious system consisting of OPC, RHA and other readily available resources such as limestone filler (LSF), normal strength concrete can still be produced having good performance and suitable for regular on-site construction. This paper explains a possible application of obtaining sufficient concrete properties from the available resources. T2 - 2nd International Conference on Advances in Cement and Concrete Technology in Africa CY - Dar es Salaam, Tanzania DA - 27.01.2016 KW - Sub-Saharan Africa KW - Rice husk ash KW - Admixtures KW - Workability KW - Rheology PY - 2016 SN - 978-3-9817502-3-2 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. SP - 323 EP - 331 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-36881 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Barthel, Maria A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten A1 - Rübner, Katrin ED - Schmidt, Wolfram ED - Priebe, Nsesheye Susan T1 - Interactions between waste paper sludge ashes and superplasticizers based on polycarboxylates N2 - In many industrial nations, about two third of the paper demand is covered by recovered paper. A major process step within the treatment of waste paper is the de-inking. It is a floating process yielding paper sludge as a waste product. About 50 % of this residue is used as a fuel. In several cases it is burnt at temperature of about 850 °C and thereafter the accrued ashes are collected in the flue gas filter. During the combustion, kaolinite and calcium oxide generate gehlenite and larnite. Calcite is the main component of waste paper sludge ash (PA).The chemical and mineralogical composition of PA suggests using it as a supplementary cementitious material. In modern construction materials technology, workability aspects gain importance, since for most modern materials the rheology and compaction ability are relevant for the operation at a hardened state. It was observed that PA significantly increases the water demand of powder systems, which can cause serious problems during the casting of mineral binder systems containing PA. It is therefore obvious that binder systems containing PA might demand for the use of superplasticizers. Superplasticizers are polymers with anionic backbone that cause electrostatic and steric repulsion effects upon adsorption on surfaces of particles and hydration phases. In this paper interactions between superplasticizers and waste paper sludge ashes are discussed and analysed. Based on observations of changes in the zeta potential and the dispersion of the particle system, the influence of the charge density of superplasticizers is observed and time dependent effects are demonstrated. T2 - 2nd International Conference on Advances in Cement and Concrete Technology in Africa CY - Dar es Salaam, Tanzania DA - 27.01.2016 KW - Waste paper sludge KW - Rheology KW - Cement KW - Concrete KW - Polycarboxylate ether PY - 2016 SN - 978-3-9817502-3-2 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. SP - 181 EP - 186 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-36877 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Priebe, Nsesheye Susan A1 - Uzoegbo, H. C. A1 - Makunza, J. K. ED - Malhotra, V. M. ED - Gupta, P. R. ED - Holland, T. C. T1 - Admixture concepts for the Sub-Saharan African environment with indigenous raw materials N2 - The economic use of chemical admixtures depends on supply chains. Therefore, in most regions ins sub-Saharan Africa (SSA), the use of admixtures is not common practice. This amplifies the unfavorable framework for concrete construction such as fragmentary supply chains, high local cement prices, and unfavorable construction site facilities in this region significantly. The use of superplasticizer (SP) and stabilizing agents (STA) can enhance the concrete technology in SSA, since they can disassociate the concrete quality from external boundary influences. After providing a general overview of the peculiarities of the SSA boundary framework, economic concepts are provided, how existing material solutions can be significantly improved by the use of SPs and STAs based on locally available materials such as lignosulphonates and cassava starch. Finally a three step optimization process is described that helps developing flowable concrete based on materials that can be accessed in most locations in SSA. T2 - 11th International Conference on Superplasticizers and Other Chemical Admixtures in Concrete CY - Ottawa, Canada DA - 12.07.2015 KW - Lignosulfonate KW - Polycarboxylate ether KW - Robustness KW - Self-compacting concrete KW - Sub-Saharan Africa PY - 2015 SN - 9781942727224 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. SP - SP-302-37, 491 EP - 505 AN - OPUS4-36860 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram ED - Schmidt, Wolfram T1 - Engineering skill requirements to cope with the local and global challenges of the future N2 - In the 21st century, adequate habitat and functioning infrastructure are critical for global societal and economic stability. In addition, growing urbanisation and environmental pollution cause challenges to societies. With increasing velocity, humanity faces that the current way of living is not sustainable. Thus, habitat,infrastructure, urbanisation, environment and sustainability are definitively among the most striking challenges of the 21st century. By consulting, planning, building, maintaining, exploiting and processing of global resources, civil engineers contribute significantly to the existence of these challenges. This is a high responsibility, but due to the heavy involvement, together with adjacent disciplines such as architecture, geosciences, chemistry, physics, environmental sciences and economics, civil engineers also hold the key to mitigate these challenges and provide a brighter global future. Solutions towards greener, more sustainable and economically viable materials do exist, and there is ongoing research on how greener technologies can contribute to better livelihood and economic growth, but their level of implementation is limited, a major reason for which is that these approaches require more fundamental understanding rather than standard application. T2 - ISEE Africa - Innovation, Science, Engineering, Education CY - Nairobi, Kenya DA - 30.01.2019 KW - Civil Engineering KW - Education KW - Sustainability KW - Materials KW - Sciences PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-484895 UR - http://isee-africa.com/wp-content/uploads/2019/07/Innovation-Science-Engineering-Education_High-Quality.pdf SN - 978-3-9818564-2-2 SP - 16 EP - 19 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-48489 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Piechotta, Christian A1 - Iznaguen, Hassan A1 - Traub, Heike A1 - Feldmann, Ines A1 - Köppen, Robert A1 - Witt, Angelika A1 - Jung, Christian A1 - Becker, Roland A1 - Oleszak, Katrin A1 - Bücker, Michael A1 - Urban, Klaus A1 - Reger, Christian A1 - Ostermann, Markus T1 - Bewitterungsszenarien im Vergleich – Veränderungen in der Oberflächenmorphologie von Polypropylen (PP) und Polystyrol (PS) unter dem Aspekt des Austrags von polybromierten Flammschutzmitteln N2 - Gegenstand der vorzustellenden Arbeiten ist die Prüfung der Umwelt-beständigkeit und -verträglichkeit von Materialien und Produkten hinsichtlich der Emission von potenziellen Schadstoffen in die Umwelt. Hierzu werden chemisch-physikalische Einflüsse (Bewitterung) und mikrobielle Beanspruchungen an Modellmaterialien evaluiert. So werden die Freisetzungsraten von Schadstoffen in Abhängigkeit der Beanspruchung beschrieben. Als Modellmaterialien kommen die Polymere Polystyrol (PS) und Polypropylen (PP) zum Einsatz. Synergistische Effekte der Bewitterungsparameter und der mikrobiologischen Beanspruchung sollen dabei ebenso betrachtet werden, wie die gezielte Alterung. Auch findet eine Beschreibung des Verhaltens der ausgetragenen Schadstoffe in den Umweltkompartimenten Boden oder Wasser statt. Hier sind mit Hilfe der zu entwickelnden Screening- und non-Target-Analyseverfahren die Transformation und der Metabolismus durch Mikroorganismen zu beschreiben. Aus den Ergebnissen sollen Korrelationen zwischen den künstlichen Alterungsverfahren und realen Szenarien abgeleitet werden. T2 - 47. Jahrestagung der GUS CY - Blankenloch-Stutensee, Germany DA - 21.03.2018 KW - Schadstoffaustrag KW - Umweltsimulation KW - Bewitterung PY - 2018 SN - 978-981-18507-2-7 VL - 47 SP - 115 EP - 128 AN - OPUS4-49802 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Torge, Manfred A1 - Feldmann, Ines A1 - Knabe, Nicole A1 - Toepel, J. T1 - Organic surface coatings on medieval stained glass and microbiological investigation N2 - Mediaeval stained glass has been treated with Polymethylmetacrylate coatings by Kwiatkowski in Poland during the 1950th. Such treated panels were found in the Johannis Church of Toruń (without protective glazing), in the Cathedral of Włocławek (behind a protective glazing), and on glass kept in exhibition cases in the museum of Toruń. Surface coatings have been detected and analyzed. There was no extensive contamination by fungi or bacteria if the glass was either coated or not. T2 - Glass Science in Art and Conservation 2017 CY - Lisbon, Portugal DA - 06.06.2017 KW - Microbiological investigation KW - Medieval stained glass KW - SEM analysis PY - 2017 SN - 978-989-99528-3-6 SP - 112 EP - 113 PB - NOVA:FCT Editorial CY - Lisbon AN - OPUS4-40568 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Le, Quynh Hoa A1 - Bäßler, Ralph A1 - Bettge, Dirk T1 - Electrochemical behaviors of casing steel/mortar interface in CO2 saturated aquifer fluid N2 - To reveal the corrosion resistance of casing steel/mortar interface in CO2 injection condition, sandwich samples were prepared and exposed up to 20 weeks in aquifer fluid under 10 MPa and 60 °C. Cross section analysis revealed the crevice corrosion as main mechanism instead of pitting corrosion, which would be expected to happen in the extremely high Chloride concentration. Detailed analysis using EDS line scan shown the slow diffusion of Chloride, suggesting why pitting did not happen after 20 weeks. To mimic the passivated steel surface, the steel coupon was passivated in simulated pore solution having pH 13.5 for 42 days. The passivated coupon was further exposed to NGB solution for 28 days. Electrochemical characterization was performed along the exposure processes to reveal the change in impedance, indicating the corrosion resistance of steel casing/mortar interface. T2 - EUROCORR 2022 CY - Berlin, Germany DA - 28.08.2022 KW - Corrosion KW - CO2 quality KW - Pipeline network KW - CCS PY - 2022 SP - 859 EP - 865 PB - European Federation of Corrosion AN - OPUS4-55622 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Le, Quynh Hoa A1 - Bäßler, Ralph A1 - Bettge, Dirk A1 - Kratzig, Andreas A1 - Knauer, S. T1 - Factors Influencing Droplet Corrosion in Dense Phase CO2 N2 - Recent studies have shown that even at a very low concentration of impurities (less than 100 ppmv of SO2, NO2, O2 and H2O) the droplet formation and condensation of sulfuric and nitric acids in dense phase CO2 are possible and observable. To reveal the mechanism of droplet corrosion in dense phase CO2 at high pressure and low temperature, further studies on factors that affect wettability and resulting corrosion behaviors of transport pipeline steels are needed. In this study, effects of surface morphology were investigated by varying surface roughness of carbon steel coupons exposed to CO2 stream containing impurities to measure the wettability by contact angle and to observe the condensation as well as possible droplet corrosion that followed. Other considered factors were: pH of the droplet, temperature, droplet volume, and exposure time. T2 - NACE International Corrosion Conference 2019 CY - Nashville, TN, USA DA - 24.03.2019 KW - CCUS KW - Dense phase KW - CO2 KW - Droplet KW - Corrosion KW - Condensation KW - Carbon steel PY - 2019 SP - 13017-1 EP - 13017-13 PB - NACE International CY - Houston AN - OPUS4-47915 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gawlitza, Kornelia A1 - Tiebe, Carlo A1 - Banach, Ulrich A1 - Noske, Reinhard A1 - Bartholmai, Matthias A1 - Rurack, Knut T1 - Novel sensor for long-term monitoring of ammonia in gas phase N2 - Because ammonia and its reaction products can cause considerable damage to human health and ecosystems, there is a need for reliably operating and reversibly interacting sensor materials to monitor traces of gaseous ammonia in ambient air, which at best can be used on-site for in-the-field measurements. Herein, the development of a sensor material for gaseous ammonia in the lower ppm to ppb range using optical fluorescence as transduction mechanism is presented. A fluorescent dye, which shows reversible fluorescence enhancement in the presence of ammonia is incorporated into a polymer matrix, the latter to ensure the accumulation of ammonia. The sensor material is integrated into a prototype of a miniaturized sensor device, facilitating long-term operation. To calibrate the optical sensor system a gas standard generator, producing standard gas mixtures, is used, leading to a sensitivity down to lower ppm concentrations of ammonia. T2 - 13. Dresdner Sensor-Symposium 2017 CY - Dresden, Germany DA - 04.12.2017 KW - Ammonia gas sensor KW - Fluorescence KW - Air quality monitoring KW - Standard gas generator KW - Miniaturized sensor device PY - 2017 DO - https://doi.org/10.5162/13dss2017/P4.02 SP - P4.02, 272 EP - 276 AN - OPUS4-43352 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nattuveettil, Keerthana A1 - Liebner, Christian A1 - Tiebe, Carlo T1 - Hydrogen safety- Dealing with Closed Spaces N2 - Hydrogen is under discussion as a potentially clean energy source, but its safe usage and handling in enclosed environments remains a critical challenge due to the properties of hydrogen. This work focuses on detecting and monitoring hydrogen concentration in closed spaces to improve safety by developing a sensor network-based leak detection system to prevent of the accumulation of hazardous mixtures. Furthermore, the study details the implementation of a hydrogen sensor network within a container, analysing sensor placement, data collection, and safety improvements. The findings contribute to better risk assessment and enhanced safety protocols in hydrogen storage and usage facilities. T2 - SMSI 2025 CY - Nuremberg, Germany DA - 06.05.2025 KW - Sensor Network KW - Hydrogen safety KW - QI-Digital PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-640630 SN - 978-3-910600-06-5 DO - https://doi.org/10.5162/SMSI2025/C6.2 SP - 167 EP - 168 PB - AMA Verband für Sensorik und Messtechnik e.V. CY - Berlin AN - OPUS4-64063 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Keserović, A. A1 - Sobetzki, J. A1 - Sarmiento-Klapper, H. A1 - Boduch, A. A1 - Aristia, G. A1 - Faes, W. A1 - Stoljarova, A. A1 - Zimmer, S. T1 - Metallene Werkstoffe in Geothermieanlagen - nicht nur aus Sicht der Korrosion N2 - Um Konstrukteuren und Nutzern geothermischer Anlagen grundlegende Informationen über die Korrosionsbeständigkeit zur Verfügung zu stellen, wurden verschiedene metallene Werkstoffe, darunter nichtrostende Duplex- und austenitische Stähle sowie eine Nickellegierung, in künstlichen Geothermalwässern, die die Bedingungen an verschiedenen Standorten mit geothermischem Potenzial simulieren, mit Hilfe von elektrochemischen und Langzeittests hinsichtlich ihrer Eignung bewertet. In hochsalinaren Umgebungen erwies sich Spaltkorrosion als der entscheidende Mechanismus. Die Nickellegierung zeigt eine ausgezeichnete Beständigkeit gegenüber Lochkorrosion. Abgesehen von ihren hohen Kosten eignet sie sich sehr gut für den Bau von Geothermieanlagen mit stark salzhaltigen Fluiden. Rostfreie Stähle und Duplexstähle weisen eine begrenzte Korrosionsbeständigkeit gegen Loch- und Spaltkorrosion auf. Daher sind sie für stark salzhaltige Fluide nicht geeignet. Der Superaustenit zeigt ein temperaturabhängiges Verhalten. In nichtsalinaren Umgebungen könnten niedriglegierte Stähle (neben den höherlegierten Werkstoffen) als Konstruktionsmaterial für Geothermieanlagen eingesetzt werden, sofern eine ausreichende Wandstärke des Materials berücksichtigt wird. Neben Korrosionsaspekten erwies sich auch die Ausfällung von Fluidbestandteilen als interessantes Thema. Beim Betrieb der Forschungsanlage in Groß Schönebeck wurden Kupfer- und Bleieffekte im Bohrloch festgestellt. Die auftretenden Mechanismen und Maßnahmen zur Verhinderung von Ausfällungen und Abscheidungen wurden ebenso untersucht, wie deren mögliche Einflüsse auf die Korrosionsbeständigkeit metallener Werkstoffe für Anlagenkomponenten. Der Beitrag beschreibt die Wechselwirkungen zwischen Geothermalwässern und Ausrüstungskomponenten. T2 - 57. Kraftwerktechnisches Kolloquium CY - Dresden, Germany DA - 07.10.2025 KW - Örtliche Korrosion KW - Edelstahl KW - Ni-Legierungen KW - Geothermie KW - Abscheidung PY - 2025 SN - 978-3-00-082651-1 SN - 978-3-00-082652-8 SP - 551 EP - 568 PB - IKS-Verlag CY - Freiberg AN - OPUS4-64320 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pötzsch, Sina A1 - Weltschev, Margit A1 - Bäßler, Ralph T1 - Compatibility of polymers exposed to heating oil blends with 10 % and 20 % biodiesel (FAME) N2 - Biodiesel (FAME) from rapeseed is an environmentally friendly alternative to common fossil fuels. It is also suitable to serve as blending component to fuels like heating oil. If the fuel composition is changed, materials compatibility must be guaranteed. Adding polar biodiesel to nonpolar heating oil, changes the blend’s solvency and might cause swelling, extraction and solvation of polymers. The objective of this research was to investigate the compatibility of polymeric materials, which are commonly used for components in middle distillate facilities, along with blends of heating oil and 20 % biodiesel (B20). For this propose, ACM, HNBR, FKM, PE, PA 6, POM, PUR and PVC were exposed to heating oil and B20 for 42 and 84 days at 40 °C. In addition, the polymers HNBR, FKM, PA, POM and PVC were also exposed at 70 °C. Furthermore, the resistance of polymers in eight-year aged B10 at 40 °C was evaluated. Ageing of biodiesel increases acidity which might propagate polymer corrosion. The materials were evaluated as resistant, if the loss in tensile properties (tensile strength and elongation at break) and Shore hardness remained under 15 % compared to the initial unexposed material values. For investigations under compressed conditions, the compression set was determined for specimens of ACM, FKM and HNBR after exposure in heating oil B0 and B20 for 3,7,14, 28, 56 and 90 days at 40 °C according to ISO 815-1. It was found that the resistance in B20 at 40 °C was given for all tested polymers except PUR. In the 8 years aged B10, PUR and POM were not compatible and ACM just conditionally compatible. At 70 °C, FKM and PVC were resistant in B20, whereas HNBR and PA 6 were not compatible. Swelling occurred for the elastomers ACM, HNBR and PUR. T2 - AMPP Annual International Corrosion Conference 2021 CY - Online Meeting DA - 19.04.2021 KW - Biodiesel KW - FAME KW - RME KW - Polymer in fuels PY - 2021 SP - 16222-01 EP - 16222-12 CY - Houston AN - OPUS4-52499 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Al-Akel, Said T1 - Aktuelle Diskussionen aus dem Fachbeirat der BAM N2 - Im Folgenden soll über aktuelle Diskussionen und Arbeitsschwerpunkte im Fachbeirat der BAM und von der Zulassungsstelle berichtet werden. Es werden Änderungen im Zusammenhang mit der Zulassungsrichtlinie für Kunststoffdichtungsbahnen vorgestellt. Es wird über die aktuelle Diskussion über die Anforderungen z. B. an metallische Sensoren für Dichtungskontrollsysteme berichtet. Änderungen der Fremdprüfung von sogenannten Sandschutzmatten, des Standards zur Qualitätsüberwachung (SQÜ) von Kunststoff Dränelementen (KDE) und der Anpassung der Formulierungen zum Überbau der in Abdichtungen verwendeten Produkte werden aufgezeigt. T2 - 20. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 12.03.2024 KW - Dichtungskontrollsystem KW - Deponie KW - Kunststoffdichtungsbahn PY - 2024 SN - 978-3-943443-54-7 VL - 20 SP - 16 EP - 23 CY - Leipzig AN - OPUS4-59893 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Die Zulassung von Geokunststoffen nach der deutschen Deponieverordnung N2 - Seit dem Erscheinen der Deponieverordnung (DepV) bedürfen Geokunststoffe, Polymere und Dichtungskontrollsysteme einer Zulassung durch die BAM, wenn diese in deutschen Deponieabdichtungssystemen eingesetzt werden sollen. Die DepV ermöglicht den Einsatz verschiedener Komponenten. Sie stellt dabei allgemeine Anforderungen an die Geokunststoffprodukte auf. Dadurch beschreibt sie den Stand der Technik für Geokunststoffe, die in deutschen Abdichtungen eingesetzt werden. Diese Anforderungen werden durch die Zulassungsrichtlinien der BAM in konkrete technische Spezifikationen überführt. In dem Beitrag wird eine Übersicht über die Produkte und die entsprechenden Anforderungen gegeben. Zudem soll erläutert werden, durch welche Qualitätsmanagementmaßnahmen eine gleichbleibende Qualität und Funktionserfüllung der Produkte gewährleistet wird. T2 - 14. DEPONIEWORKSHOP Liberec - Zittau 2018 CY - Liberec, Czech Republic DA - 15.11.2018 KW - Deponie KW - Geokunststoffe KW - Polymere KW - Dichtungskontrollsysteme PY - 2018 VL - 14 SP - 149 EP - 158 PB - Technische Universität Liberec, Hochschule Görlitz/Zittau CY - Liberec, Tschechien AN - OPUS4-46660 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Kim, Bumjoo ED - Kim, Yun-Tae ED - Hong, Gigwon ED - Jung, Young-Hoon ED - Chong, Song-Hun T1 - The “zero leakage” approach and German regulations for geosynthetics used in landfill liner and capping systems N2 - An approach to achieve “zero leakage” is discussed with respect to the experience in Germany, where strict regulations for landfill lining and capping systems have been developed and issued because of large environmental problems related to landfills that accumulated in the 1970’s and 1980’s. These regulations for landfills and geosynthetics which are used in landfill liner and capping systems are shortly described. The main certification requirements for the products as well as conclusions for their use are presented. Using a thick, high quality HDPE geomembrane (GMB), which is installed free of residual waves and wrinkles in intimate contact with a compacted clay liner (CCL) or geosynthetic clay liner (GCL) of very low permeability, by a qualified, experienced, well equipped and properly third‐party controlled installer and which are protected by heavy protection layers designed with respect to long‐term performance of the GMB, may result in a liner or capping system of practically no leakage. This is demonstrated by analyzing results of measurements obtained from permanently installed leak detection systems in combination with HDPE GMBs. T2 - 11th International Conference on Geosynthetics CY - Seoul, Korea DA - 16.09.2018 KW - HDPE geomembrane KW - Landfill liner KW - Leak detection KW - Regulations PY - 2018 VL - 11 SP - 1 EP - 8 AN - OPUS4-46030 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Al-Akel, S. T1 - Aktuelle Diskussionen zur vorläufigen Zulassungsrichtlinie von Bewehrungsgittern für Deponieoberflächenabdichtungen und zu Auftragsnähten in Kunststoffdichtungsbahnen N2 - Die BAM wurde 2009 u. a. mit der Zulassung von Bewehrungsgittern für den Deponiebau beauftragt. Der Stand von Wissenschaft und Technik bot jedoch keine ausreichende Grundlage, die tatsächlich relevanten Widerstände und die mit diesen Widerständen verbundene Wechselwirkung zwischen Gitter und Boden im Hinblick auf eine mindestens 100-jährige Funktionsdauer realistisch beurteilen zu können. Es wurde daher nur eine vorläufige Zulassungsrichtlinie für diese Produkte erarbeitet. In der Zwischenzeit hat sich ein neuer Kenntnisstand ergeben. Vor diesem Hintergrund hat die AG (Arbeitsgruppe) Geogitter des Fachbeirats der BAM am 26.09.2017 getagt. Es sollen die aktuellen Erkenntnisse und Schlussfolgerungen für die Zulassung in Kürze vorgestellt werden. Die entsprechenden Kapitel beruhen dabei auf einem Arbeitspapier von W.W. Müller und dem Autoren, das der Arbeitsgruppe zur Diskussion vorgelegt wurde. Weiterhin soll über Entwicklungen in Zusammenhang mit Kunststoffdichtungsbahnen (KDB) berichtet werden. Die Anforderungen an die Schweißzusätze für das Extrusionsschweißen wurden angepasst. Zudem soll über die aktuelle Diskussion der Schweißbarkeit unterschiedlicher HDPE Materialien informiert werden. Die maßgebliche DVS (Deutscher Verband für Schweißen und verwandte Verfahren) Richtlinie 2225-4 wird derzeit offenbar so ausgelegt, dass Materialien mit völlig unterschiedlichen Schmelze-Massefließrate miteinander verbunden werden können. Dies steht allerdings im grundlegenden Widerspruch zum Stand der Technik. T2 - 14. Leipziger Deponiefachtagung - Planung, Bau, Betrieb, Stilllegung, Nachsorge und Nachnutzung von Deponien CY - Leipzig, Germany DA - 06.03.2018 KW - Deponietechnik KW - Bewehrungen aus Kunststoff KW - Kunststoffschweißen PY - 2018 SN - 978-3-943443-47-9 VL - 14 SP - 53 EP - 68 AN - OPUS4-44417 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schraut, Katharina A1 - Adamczyk, Burkart A1 - Simon, Sebastian A1 - von Werder, Julia A1 - Meng, Birgit A1 - Stephan, D. A. A1 - Adam, Christian T1 - Zementklinker durch Nachbehandlung von Stahlwerksschlacken N2 - Die Klinkerphasenbildung durch Sinterung in Drehrohröfen bei der Herstellung von Portlandzementklinker (PZK) ist gründlich erforscht und optimiert. Im Hinblick auf mögliche ökonomische und ökologische Vorteile befassen sich aktuelle Forschungsvorhaben darüber hinaus mit der Herstellung von Klinkermineralen aus Stahlwerksschlacken, die eine vergleichbare chemische Zusammensetzung aufweisen. Neuste Untersuchungen zeigen, dass nach der reduzierenden Behandlung schmelzflüssiger Linz-Donawitz-(LD)-Schlacken und Abscheidung des gebildeten metallischen Eisens eine mineralische Schlacke entsteht, die unabhängig von ihren Abkühlbedingungen ca. 50–60 Gew.% des wichtigsten Klinkerminerals Alit (C3S) enthält und eine hohe hydraulische Reaktivität aufweist. Die Stabilität des Alits auch nach langsamer Abkühlung deutet auf eine Stabilisierung des Minerals durch Nebenelemente aus den LD-Schlacken hin. Ein sinkender Anteil an LD-Schlacke durch Zusatz synthetischer Schlackemischung, die sich hinsichtlich ihrer Hauptkomponenten wie eine ausreduzierte LD-Schlacke zusammensetzt, führt zu einem Rückgang des Alitgehaltes und dem Zerfall der Schlacke beim Erstarren. T2 - 5. Schlacken-Symposium CY - Meitingen, Germany DA - 25.10.2018 KW - LD-Schlacke KW - Zement KW - Tricalciumsilikat PY - 2018 SP - 219 EP - 229 PB - Max Aicher Unternehmensgruppe AN - OPUS4-46412 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas A1 - Müller, Werner ED - Al-Akel, S. T1 - Aktuelle Themen aus der Arbeit des BAM-Fachbeirats und von der -Zulassungsstelle N2 - Welche Themen und Fragestellungen haben den Fachbeirat der BAM, seine Arbeitsgruppen und die BAM seit der letzten Fachtagung in Leipzig beschäftigt? Die Richtlinie Fremdprüfer und deren Anlagen wurden entsprechend der aktuellen Anforderungen angepasst. Die einzelnen Punkte wollen wir vorstellen. Im Zusammenhang mit Geotextilien zum Filtern und Trennen und Kunststoff Dränelementen wurden zwei Themen bearbeitet: (1) Die europäischen Anwendungsnormen und das deutsche Straßenbaumerkblatt für Geokunststoffe verwenden statistische Begriffe. Deren nur „beiläufige“ Erwähnung lässt jedoch offen, was genau im Zusammenhang gemeint ist. Produkte unterschiedlicher Hersteller können daher trotz gleicher Angaben zu den Mindestwerten in den Leistungserklärungen oder Datenblättern deutlich unterschiedliche Eigenschaften haben. Um vorschriftsmäßig bemessen zu können, muss man jedoch wissen, was sich hinter den Zahlen verbirgt. Eine Zulassung oder Zertifizierung ist nur dann sinnvoll, wenn darüber hinaus einheitlich definiert wird, was die Angaben für die werkseigene Produktionskontrolle, die Inspektion durch benannte Stellen und die Kontrolle durch Dritte bedeuten. In den vergangenen Jahren seit 2009 wurde versucht, die Zulassungen stärker auf die Vorgaben aus der europäischen Normung zu stützen. Daher musste nun diskutiert werden, welche statistische Bedeutung die Angaben in den Zulassungen für Kunststoff Dränelementen und Geotextilien zum Filtern und Trennen haben. Hier musste eine einheitliche Regelung getroffen werden. (2) Die Langzeiteigenschaften von polyolefinen Geokunststoffen sind maßgeblich von den eingesetzten Stabilisatoren abhängig. Wie kann hier eine Überwachung während der Produktion der Geokunststoffe implementiert werden, wenn die Rezepturbestandteile der Produkte sensible Firmengeheimnisse der Rohstoffhersteller sind? Hier musste eine Lösung erarbeitet werden. Über die Ergebnisse soll berichtet werden. Wir möchten weiterhin über Entwicklungen in Zusammenhang mit Kunststoffdichtungs-bahnen (KDB) berichten. Die DVS (Deutscher Verband für Schweißen und verwandte Verfahren) Richtlinie 2225-4 regelt das Schweißen der KDB auf der Deponiebaustelle. Werden KDB im strukturierten Bereich miteinander verschweißt, werden die Strukturen in der Regel vorher abgetragen. Die DVS Richtlinie sieht unter bestimmten Voraussetzungen von einem Abtragen der Strukturen ab. Vor diesem Hintergrund wurde vom AK GWS ein Untersuchungsprogramm initiiert, das die Auswirkungen aufzeigen soll. Darüber haben wir bereits im letzten Jahr berichten. Das Untersuchungsprogramm wurde abgeschlossen. Die Ergebnisse und Schlussfolgerungen werden nun vorgestellt. T2 - 13. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 07.03.2017 KW - Deponie KW - Fremdprüfung KW - Kunststoffdichtungsbahnen KW - Geotextilien PY - 2017 SN - 978-3-943443-43-1 SP - 43 EP - 56 AN - OPUS4-39312 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Egloffstein, Thomas ED - Burkhardt, Gerd T1 - Arbeits- und Diskussionsthemen aus dem Fachbeirat der BAM und von der Zulassungsstelle N2 - Die BAM wurde 2009 u. a. mit der Zulassung von Bewehrungsgittern für den Deponiebau beauftragt. Der Stand von Wissenschaft und Technik bot jedoch keine ausreichende Grundlage, die tatsächlich relevanten Widerstände und die mit diesen Widerständen verbundene Wechselwirkung zwischen Gitter und Boden im Hinblick auf eine mindestens 100-jährige Funktionsdauer realistisch beurteilen zu können. Es wurde daher nur eine vorläufige Zulassungsrichtlinie für diese Produkte erarbeitet. In der Zwischenzeit hat sich ein neuer Kenntnisstand ergeben. Vor diesem Hintergrund hat die AG (Arbeitsgruppe) Geogitter des Fachbeirats der BAM am 26.09.2017 getagt. Es sollen die aktuellen Erkenntnisse und Schlussfolgerungen für die Zulassung in Kürze vorgestellt werden. Die entsprechenden Kapitel beruhen dabei auf einem Arbeitspapier von W.W. Müller und dem Autoren, das der Arbeitsgruppe zur Diskussion vorgelegt wurde. Weiterhin soll über Entwicklungen in Zusammenhang mit Kunststoffdichtungsbahnen (KDB) berichtet werden. Die Anforderungen an die Schweißzusätze für das Extrusionsschweißen wurden angepasst. Zudem soll über die aktuelle Diskussion der Schweißbarkeit unterschiedlicher HDPE Materialien informiert werden. Die maßgebliche DVS (Deutscher Verband für Schweißen und verwandte Verfahren) Richtlinie 2225-4 wird derzeit offenbar so ausgelegt, dass Materialien mit völlig unterschiedlichen Schmelze-Massefließrate miteinander verbunden werden könnten. Dies steht allerdings im grundlegenden Widerspruch zum Stand der Technik. Derzeit gibt es intensive Diskussion über die Entlassung von Deponien aus der Nachsorge. Sind Geokunststoffe in den Böschungen einer Deponie verwendet worden, wäre eine Entlassung aus der Nachsorge demnach im Moment nicht möglich. Die Deponie müsste dafür nach der Deponieverordnung (DepV) u. a. „insgesamt dauerhaft standsicher“ sein. Geokunststoffe erfüllten ihre Funktion über einen Zeitrahmen von mindestens hundert Jahren. Die Dauerhaftigkeit wird bei der Diskussion aber offenbar als „Ewigkeit“ verstanden. Dies stehe somit im Widerspruch – so die Argumentation. Auf dieser Veranstaltung wurde im vergangenen Jahr darüber berichtet. Auch auf dieses Thema wird eingegangen. T2 - Abschluss und Rekultivierung von Deponien und Altlasten - Planung und Bau neuer Deponien CY - Karlsruhe, Germany DA - 18.10.2017 KW - Bewehrungen aus Kunststoff KW - Deponien KW - Schweißen PY - 2017 SN - 978-3-939662-21-1 VL - 32 SP - 61 EP - 76 PB - ICP Eigenverlag Bauen und Umwelt CY - Karlsruhe AN - OPUS4-42595 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Schneider, Joachim A1 - Schraut, Katharina T1 - Strategien für die Nutzung von Schlacken zukünftiger wasserstoffbasierter Stahlproduktionsrouten – Herstellung von Stahlwerksschlacke basierten Ausgangsstoffen für die Zementindustrie N2 - Die Europäische Kommission präsentierte am 11. Dezember 2019 den European Green Deal, ein Konzept mit dem Ziel, bis zum Jahr 2050 als erster Kontinent Klimaneutralität zu erreichen. Mit Inkrafttreten der Verordnung (EU) 2021/1119 des Europäischen Parlaments und des Europäischen Rates am 29. Juli 2021 zur Schaffung des Rahmens für die Verwirklichung der Klimaneutralität („Europäisches Klimagesetz“), ist dieses, sowie das Ziel der Reduzierung der Nettotreibhausgasemissionen um mindestens 55 % bis 2030 in der Gesetzgebung der Europäischen Union verankert. Die Stahlindustrie in der Europäischen Union mit ca. 57 Mio. t Nettotreibhausgasemissionen im Jahr 2020, die annähernd 2 % der Emissionen der Europäischen Union ausmachen (Inklusive Energie: 127 Mio. t; 4 %), bekennt sich zur erheblichen Reduzierung der CO2-Emissionen bis zum Jahr 2030 und zum Erreichen der Klimaneutralität bis zum Jahr 2050. Als Schlüsselwege zur Verwirklichung dieser Zielstellung hat sie zum einen Smart Carbon Usage (SCU) und zum anderen Carbon Direct Avoidance (CDA) in einer Roadmap formuliert. SCU umfasst CO2-reduzierende Maßnahmen in bestehenden Eisen- und Stahlproduktionsprozessen, Carbon Capture and Storage- (CCS) sowie Carbon Capture and Usage-Technologien (CCU). Wohingegen bei CDA CO2-Emissionen durch erneuerbare elektrische Energie sowie wasserstoffbasierte Reduktion des Eisenerzes gar nicht erst entstehen sollen. Der CDA-Weg, der voraussichtlich beschritten werden muss, um eine klimaneutrale Stahlproduktion zu erreichen [38], geht mit einer kostenintensiven Transformation der Stahlproduktion einher, die bereits von vielen Unternehmen der Stahlindustrie eingeleitet wurde und von der im Wesentlichen die beiden in Europa vorherrschenden Stahlproduktionsrouten Hochofen-Konverter-Route und Elektrolichtbogenofen-Route betroffen sind. Die CO2-Emissionen der Hochofen-Konverter-Route, von denen der überwiegende Anteil auf den Hochofen fällt, liegen laut einer für das Jahr 2015 erstellten Studie bei 1921 kg CO2/t Rohstahl inklusive der CO2-Last der Pellets als Einsatzmaterial sowie der Emissionen der nachgelagerten Stranggießanlagen und Walzwerke. Im Hochofen wird das Eisenerz durch Kohlenstoff (C) bzw. Kohlenstoffmonoxid (CO) – welche größtenteils aus dem Koks, der dem Hochofen zusammen mit dem Möller über die Gicht zugeführten wird, stammen – unter Entstehung von Roheisen und Kohlenstoffdioxid (CO2) reduziert. Das neben dem CO2 im Prozessgas enthaltene CO wird zum Beispiel zur Energiegewinnung in peripheren Prozessen ebenfalls unter Bildung von CO2 verbrannt. Zusätzlich zur Reduktion hat der Koks unter anderem physikalische Aufgaben, wie die Errichtung eines Stützgerüstes und die Gewährleistung der Permeabilität im Hochofenprozess. Somit ist eine vollkommene Substitution des Kokses zur Vermeidung der CO2-Emissionen im Hochofen nicht denkbar. Viele Strategien der Stahlunternehmen zum Erreichen der Klimaziele verfolgen daher den Wechsel von der Rohstahlproduktion aus der Hochofen-Konverter-Route hin zur Rohstahlproduktion im Elektrolichtbogenofen (EAF – Electric Arc Furnace) mit dem Einsatz von direkt reduziertem Eisen (Eisenschwamm, DRI – Direct Reduced Iron) aus vorgelagerten Direktreduktionsanlagen, die mit Wasserstoff (H2) als Reduktionsmittel betrieben werden können. Dabei ist die Elektrostahlerzeugung kein neuer Prozess und nimmt in der europäischen Union bereits jetzt einen Anteil von ca. 44 % der Rohstahlproduktion ein, jedoch überwiegend mit Schrott als Einsatzmaterial. Bei der Elektrostahlerzeugung mit Schrotteinsatz fallen laut der oben genannten Studie von Lüngen für das Jahr 20152 410 kg CO2-Emissionen pro Tonne Rohstahl an, von denen der Großteil auf die CO2-Last der fremd bezogenen elektrischen Energie zurückzuführen ist und daher nicht im Produktionsprozess selbst entsteht. Auch die Direktreduktion wird schon seit 1972 in der weltweit zweiten und bis heute in Westeuropa einzigen Direktreduktionsanlage in Hamburg betrieben. Während hier noch mit einem Reduktionsgas gearbeitet wird, das hauptsächlich aus einem aus Erdgas gewonnenen Wasserstoff-Kohlenstoffmonoxid-Gemisch besteht, liegt eine aktuelle Kernherausforderung in der Bereitstellung des in der Größenordnung der von der Transformation betroffenen Rohstahlproduktionskapazitäten notwendigen, mit erneuerbarer elektrischer Energie hergestellten Wasserstoffs. Wird zusätzlich der Strom für das Einschmelzen im Elektrolichtbogenofen aus erneuerbaren Quellen gewonnen und werden schließlich als Brennstoff verwendete Kohle und als Brennstoff verwendetes Erdgas durch CO2-neutrale Bio-Brennstoffe ersetzt, sind sowohl für den Einsatz von mit Wasserstoff reduziertem und auf Pellets ohne CO2-Last basiertem Eisenschwamm als auch für den Einsatz von Schrott CO2-Emissionen von jeweils nur 60 kg CO2/t Rohstahl erreichbar, was eine Reduktion der Emissionen, ausgehend von der Konverter-Hochofen-Route um 97 % und ausgehend von der Schrott-Elektrolichtbogenofen-Route um 85 % bedeuten würde. Der Betrieb von Elektrolichtbogenöfen macht die an den Standorten vorhandenen Konverter sowie die Infrastruktur für Behandlung und Transport des Roheisens überflüssig. Die fortwährende Nutzung dieser bestehenden Anlagenstruktur dient daher unter anderem als Motivation für die Entwicklung einer zweiten Transformationsstrategie, die einen sogenannten Einschmelzer (SAF – Submerged Arc Furnace) als der Direktreduktionsanlage nachgelagerten Prozess vorsieht, in dem wiederum Roheisen erschmolzen wird, das anschließend im Konverter zu Rohstahl veredelt wird. Die Transformation der Stahlindustrie beeinflusst einen weiteren CO2-intensiven Industriesektor, nämlich die Zementindustrie die verantwortlich ist für rund 4 % der CO2-Emissionen in der EU. Etwa zwei Drittel dieser Emissionen entfallen als Prozessemissionen auf die Entsäuerung des Rohstoffs Kalkstein (CaCO3), also auf die Abspaltung von CO2 unter Entstehung des für die Herstellung von Zementklinker notwendigen Branntkalks (CaO) als Zwischenstufe bei der Bildung der hydraulischen Phasen Tri- und Dicalciumsilikat. Als eines der fünf Themenfelder (5C-Ansatz: Clinker, Cement, Concrete, Construction, Carbonation), welche die europäische Zementindustrie entlang ihrer Wertschöpfungskette zum Erreichen der gesetzlichen Vorgaben der europäischen Union erarbeitet hat, umfasst das Feld "Cement" zum größten Teil die Reduzierung des Klinker-Zement-Faktors. Im Jahr 2017 betrug er 77 %, das heißt, dass 23 % des Klinkers durch alternative Materialien ersetzt wurden. Bis zum Jahr 2030 wird ein Faktor von 74 % und bis zum Jahr 2050 von 65 % angestrebt. Den größten Anteil an den Klinkersubstituten hat mit 33 % der Hüttensand aus der Stahlindustrie. Bei der Roheisenproduktion im Hochofen entsteht als Nebenprodukt Hochofenschlacke, die unter Zugabe von Schlackebildnern die Gangart des Möllers und mineralische Koksbestandteile abbindet, sowie weitere unerwünschte Begleitelemente wie Schwefel und Alkalien aufnimmt. Allein in Deutschland wurden im Jahr 2021 6,90 Mio. t – das entspricht 90 % der gesamten produzierten Hochofenschlacke – zu glasig erstarrtem Hüttensand granuliert. Dieser Hüttensand besitzt latent hydraulische Eigenschaften und wird daher seit mehr als 140 Jahren als Zementbestandteil eingesetzt, wodurch in Deutschland jährlich rund 4,5 Mio. t CO2-Emissionen eingespart werden. Alle Transformationsstrategien der Stahlindustrie beinhalten die notwendige Außerbetriebnahme der CO2-intensiven Hochöfen. Dies hat unter anderem zur Folge, dass die Hochofenschlacke als Nebenprodukt der Rohstahlerzeugung im Hochofen nicht mehr zur Verfügung stehen wird, wodurch die weitere Reduzierung des Klinker-Zement-Faktors erhebliche Zusatzmengen alternativer Materialien benötigen wird. Derzeit ist noch unklar, ob z.B. calcinierte Tone im benötigten Umfang erzeugt werden können. Der Fachbereich Thermochemische Reststoffbehandlung und Wertstoffrückgewinnung der Bundesanstalt für Materialforschung und -prüfung (BAM) und das Institut für Baustoffforschung FEhS forschen zusammen mit Industriepartnern und weiteren Forschungseinrichtungen im Rahmen zweier Projekte in den Kooperationssphären der Stahl- und Zementindustrie, die zur Bewältigung dieser Herausforderungen beitragen. Im Projekt SlagCEM wird die Produktion eines hydraulischen Zementbestandteils durch Reduktion von Konverter- bzw. Linz-Donawitz-Schlacke (LDS) untersucht. Die mit den zusätzlich aufgenommen Lichtbogenofenkapazitäten steigenden Mengen an Elektrolichtbogenofenschlacke (EOS, engl. electric arc furnace slag, EAFS) werden im Projekt DRI-EOS behandelt, welches die Produktion eines latent hydraulischen Hüttensandsubstituts zum Ziel hat. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 12.06.2023 KW - Stahlwerksschlacke KW - Zementersatz PY - 2023 SN - 978-3-944310-72-5 VL - 10 SP - 222 EP - 233 PB - TK-Verlag CY - Neuruppin AN - OPUS4-57684 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holm, O. A1 - Leube, Peter A1 - Vogel, Christian A1 - Kennedy, E. A1 - Stockenhuber, M. A1 - Lucas, J. A1 - Truong, T. A1 - Rappé, A. A1 - Lu, W. A1 - Blotevogel, J. T1 - Thermische Zerstörung von PFAS in der Sondermüllverbrennung: Einfluss von Temperatur und PFAS-Konzentration N2 - Aufgrund ihrer einzigartigen molekularen Beschaffenheit werden per- und polyfluorierte Alkylsubstanzen (PFAS) in vielen unterschiedlichen Produkten und Anwendungsgebieten eingesetzt. Da sie generell eine hohe Persistenz aufweisen und je nach individueller Struktur unterschiedlich mobil sind, sind sie mittlerweile in allen Umweltkompartimenten und ubiquitär nachzuweisen. Ihre potenzielle (ökologische) Toxizität birgt dabei erhebliche Umweltrisiken, weshalb PFAS in den letzten Jahren mehr und mehr in den Fokus von Umweltverbänden und -behörden gelangten. Gleichzeitig beschäftigen sich Forschungseinrichtungen mit der möglichst weitreichenden Entfernung aus der Umwelt sowie mit deren (anschließender) Zerstörung. Im Projekt ER24-4073 „Untersuchung des thermischen Abbaus von PFAS in einer kommerziellen Großanlage zur Verbrennung gefährlicher Abfälle“, welches vom U.S. Department of Defense (DoD ) über das Strategic Environmental Research and Development Program (SERDP) gefördert wird, untersuchen deutsche, australische und amerikanische Partner die Behandlung von PFAS-haltigen Abfallströmen in einer großtechnischen Verbrennungsanlage, um die Einsatzbereitschaft, Machbarkeit und Sicherheit dieser Zerstörungsmethode zu demonstrieren. T2 - Berliner Konferenz Abfallwirtschaft und Energie CY - Berlin, Germany DA - 28.01.2026 KW - Per- and polyfluoroalkyl substances (PFAS) KW - Verbrennung KW - Kontaminierter Boden PY - 2026 SN - 978-3-911006-65-1 SP - 66 EP - 77 PB - TK Verlag AN - OPUS4-65513 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taube, Mareike Carolin A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Schulenburg, F. A1 - Bartmann, U. A1 - Beckmann, T. A1 - Michalik, K. A1 - Reuter, M. A1 - Stelter, M. T1 - Optimisation of a Pyrometallurgical Niobium and Tantalum Recyling Process with on-line-LIBS N2 - Tantalum and niobium are essential for the development of electronics towards a more and more compact design, but without reducing their performance today. Especially in smart phones and tablets, tantalum and niobium capacitors with high charge densities have already become almost indispensable. However, tantalum as a critical raw material is still a problem for the sustainable production of electronics. Due to this fact, the existence of efficient recycling processes especially in Europe is becoming even more important nowadays. The Bundesanstalt für Materialforschung und -prüfung (BAM) is currently working on the optimisation of an existing pyrometallurgical tantalum recycling process. Optimisation of this industrial process is carried out in a small-scale electric arc furnace (480 kVA, capacity approx. 150 kg/h) at BAM using a new and innovative equipment for on-line analysis of high temperature processes. The aim of this project is to identify the best timing for an optimum slag tapping, when the slag is lower than minimum targeted tantalum concentration. Hence, LIBS (Laser induced breakdown spectroscopy) is used to identify the chemical composition of the slag layer and during slag tapping. The on-line-LIBS prototype of BAM enables an in-situ measurement of the element distribution in the melt after calibration on the slag system. First results of this joint research project will be presented including LIBS-measurements and thermodynamic and kinetic aspects of the process. T2 - European Mineral Processing & Recycling Congress (EMPRC 2018) CY - Essen, Germany DA - 25.06.2018 KW - Laser-induced breakdown spectroscopy KW - On-line analysis KW - Tantalum KW - Niobium KW - Pyrometallurgy PY - 2018 SN - 978-3-940276-84-1 SP - 347 EP - 362 PB - GDMB Verlag GmbH CY - Clausthal-Zellerfeld AN - OPUS4-47040 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taube, Mareike Carolin A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Beckmann, T. A1 - Reuter, M. A1 - Stelter, M. T1 - Influence of carbon feeding on a pyrometallurgical tantalum and niobium recycling process and the formation of carbides N2 - An existing pyrometallurgical process for tantalum and niobium recovery, mainly from low grade pyrometallurgical residues, was investigated. Series of melting experiments were carried out in a pilot-scale electric arc furnace to study how the amount, the grain size and the way of feeding affect the activity of carbon as a reducing agent. During the pyrometallurgical treatment refractory metals such as tantalum and niobium are reduced to their carbide form and enriched in the molten iron-based metal phase. The cooled down slag and metal phase were analysed to investigate thermodynamic and kinetic conditions of the carbide formation. FACT Sage simulations were also used to investigate the material system in state of thermodynamic equilibrium. Results show that mass transfer and kinetics may play an important role if compared to equilibrium analyses using FACT Sage. T2 - Euopean Metallurgical Conference (EMC) 2019 CY - Düsseldorf, Germany DA - 23.06.2019 KW - Pyrometallurgy KW - Tantalum KW - Carbide formation KW - Reduction process KW - Carbon feeding PY - 2019 SN - 978-3-940276-87-2 VL - 1 SP - 371 EP - 386 PB - GDMB Verlag GmbH CY - Clausthal-Zellerfeld AN - OPUS4-48363 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Schröder, Simon Alexander A1 - Richter, Matthias A1 - Horn, Wolfgang A1 - Stephan, Ina A1 - Hohmann, Gloria A1 - Ziegert, Christof T1 - Identifikation und Einordnung von historischen Lehmbauteilen für die Wiederverwendung hinsichtlich Anreicherung von Schadstoffen und bauschädlichen Salzen T1 - Identification and classification of historical earth construction elements for recycling in respect of accumulation of pollutants and structurally damaging salts N2 - Lehmbaustoffe, einschließlich Lehm aus dem historischen Baubestand, bieten ein hohes Potenzial für ihre Wiederverwendbarkeit und die Schonung natürlicher Ressourcen. Zur Bewertung des Wiederverwendungspotenzials gibt es nur wenige Studien hinsichtlich der Schadstoffbelastung und der Anreicherung von Salzen in Gebäuden aus dem historischen Bestand. Tonminerale, die in Lehmbaustoffen als Bindemittel fungieren, können Schadstoffe binden. Die Region Mitteldeutschland ist geprägt durch jahrzehntelange Einwirkung erheblicher Schadstoffemissionen aus der Chemie- und Braunkohleindustrie. Der Eintrag von Schadstoffen in Lehmbaustoffe ist außerdem aus geogenen Hintergrundbelastungen denkbar, z. B. in Auenböden beeinflusst durch Einträge aus dem Erzbergbau. Salzbildende Anionen wie Chloride oder Nitrate können aufgrund ihrer hohen Löslichkeit mittels kapillarer Kräfte durch die Porenstruktur transportiert werden. In Lehmwänden können sie vor allem in oberflächennahen Lagen, in denen höhere Verdunstungsraten vorherrschen, durch Bindung mit in Lösung vorliegenden oder baustoffeigenen Kationen auskristallisieren und bauschädliche Salze ausbilden. Auch durch spezifische Nutzungen akkumulierte Schadstoffe, z. B. durch die Einwirkung von Tabakrauch, könnten theoretisch einer Wiederverwendung von Lehm entgegenstehen. In Anbetracht der Herausforderungen hinsichtlich der klimatischen und gesellschaftlichen Veränderungen, sind wissenschaftliche Erkenntnisse im Lehmbau erforderlich, die eine Integration in eine nachhaltige Kreislaufwirtschaft ermöglichen. Bei bisherigen Gesetzgebungsverfahren zu rezyklierten Baustoffen wurden Lehmbaustoffe noch nicht berücksichtigt. Ziel einer Vorstudie im Rahmen der WIR!-Initiative GOLEHM ist die Überprüfung der Wiederverwendbarkeit Wiederverwendbarkeit von Lehmbaustoffen aus historischen Bauten an Stichproben hinsichtlich der Umwelt- und Nutzerverträglichkeit. Für den Raum Mitteldeutschland können damit Anhaltspunkte darüber gegeben werden, welche Schadstoffe und bauschädlichen Salze in welchem Maße in Lehmbaustoffen aus dem Gebäudebestand erwartet werden können. Daraus können Hinweise zum Umgang mit Lehmbaustoffen aus historischen Gebäuden abgeleitet werden. Darüber hinaus wurden exemplarisch an zwei Gebäuden mikrobiologische Untersuchungen zur Ermittlung einer möglichen Belastung mit Schimmelpilzen vorgenommen. N2 - Earth construction materials, including earth from historical building stock, offer high potential in terms of their recyclability and sparing use of natural resources. Yet, only a few studies have been conducted on the levels of pollutants and the accumulation of salts in buildings from the historical building stock to enable an assessment of the potential for recycling. The aim of a preliminary study as part of the GOLEHM Initiative from WIR! is to use spot checks to review the recyclability of earth construction materials from historical buildings in terms of environmental impact and tolerance by users. This could provide indicators for the Central Germany region on which pollutants and structurally damaging salts can be expected in earth construction materials from the building stock and to what extent, allowing conclusions to be drawn on how to manage earth construction materials from historical buildings. Additionally, microbiological inspections of two sample buildings were performed to assess a potential contamination with mould. T2 - Lehm 2024 Fachtagung CY - Weimar, Germany DA - 27.09.2024 KW - Lehm KW - Wiederverwendung KW - Kreislaufwirtschaft KW - Schadstoffe KW - Bauschädliche Salze PY - 2024 SP - 1 EP - 8 CY - Weimar AN - OPUS4-61883 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taube, Mareike Carolin A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Beckmann, T. A1 - Reuter, M. A1 - Stelter, M. ED - Thiel, S. ED - Thomé-Kozmiensky, E. ED - Pretz, T. ED - Senk, D. G. ED - Wotruba, H. T1 - Tantal-Rückgewinnung aus Zinnschlacken und weiteren Reststoffen N2 - Since the recycling of tantalum bearing post-consumer waste is practically not existent, metallurgical residues are the most important feed for the tantalum recycling. Most tin ores naturally contain significant quantities of refractory metals. During the smelting process in primary tin production these elements are enriched in the slag phase. This slag is a highly valuable raw material for tantalum production due to its considerable concentration of tantalum and its functioning as an additional slag former in further pyrometallurgical treatment. In this paper the first process stage of an existing pyrometallurgical process for tantalum recovery, mainly from low grade pyrometallurgical residues, is discussed. Smelting trials were carried out in a pilot-scale electric arc furnace to analyse the effect of feeding on the activity of carbon as a reducing agent. Therefore, blowing petroleum coke through an iron lance and the manual adding of coke into the melting bath were tested. During the pyrometallurgical treatment elements with a high affinity to carbon were reduced to their carbide form and enriched in the molten iron-based metal phase. The objective of the process was to reduce the oxidic tantalum completely and to enrich it into the metal phase. Furthermore, the transfer of unwanted elements such as titanium into the metal phase was aimed to be avoided. Spoon test specimens were taken from the liquid mineral melt to follow the evolution of the reduction process. The cooled down solidified melting bath was investigated by using the XRD and EDX method to characterise the slag system and to identify relevant mineral phases. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 13.05.2019 KW - Zinnschlacke KW - Tantal KW - Recycling KW - Pyrometallurgie KW - Lichtbogenofen PY - 2019 SN - 978-3-944310-47-3 VL - 6 SP - 378 EP - 393 PB - Thomé-Kozmiensky Verlag GmbH CY - Neuruppin AN - OPUS4-48357 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Al-Akel, S. T1 - Aktuelle Diskussionen aus dem Fachbeirat der BAM N2 - Vor nun 30 Jahren im Jahre 1989 wurde die erste Zulassung für eine Kunststoffdichtungsbahn von der BAM auf der Grundlage des „Niedersächsischen Dichtungserlasses“ erteilt. Vor ungefähr 10 Jahren wurde die BAM mit dem Erscheinen der Deponieverordnung (DepV) mit der Zulassung von Geokunststoffen, Polymeren und Dichtungskontrollsystemen beauftragt. Wir möchten dies zum Anlass nehmen, an dieser Stelle den viele ehrenamtlichen Experten des Fachbeirats und seiner Arbeitsgruppen für ihren Einsatz und die Unterstützung zu danken. Darüber hinaus soll über aktuelle Arbeitsthemen und Entwicklungen im Fachbeirat berichtet werden. So soll in einer Sondersitzung des Fachbeirats über die Entlassung aus der Nachsorgephase beim Einsatz von Geokunststoffprodukten in Böschungen diskutiert werden. Es ist geplant, in einer Unterarbeitsgruppe eine Sitzung über die Fremdüber¬wachung in der Produktion abzuhalten. Darüber hinaus werden Änderungen in den Zulassungsrichtlinien für Kunststoff Dichtungsbahnen und Kunststoff Dränelemente kurz vorgestellt. In der Zwischenzeit wurde auch die abschließende Zulassungsrichtlinie für Geogitter verabschiedet. Neue Fragestellungen sind hier entstanden. Unter welchen Voraussetzungen können Geogitter in Zwischenabdichtungen eingesetzt werden. Bisher können diese Produkte formal nur in Oberflächenabdichtungen eingesetzt werden. Auch auf diese beiden Themen soll im Folgenden in Kürze eingegangen werden. T2 - 15. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 05.03.2019 KW - Deponie KW - Abdichtungssysteme KW - Geogitter PY - 2019 SN - 978-3-943443-48-6 VL - 15 SP - 29 EP - 40 PB - HTWK Leipzig CY - Leipzig AN - OPUS4-47490 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Themen aus der Arbeit des Fachbeirats der BAM N2 - Vor nun 30 Jahren, im Jahre 1989, wurde die erste Zulassung für eine Kunststoffdichtungsbahn (KDB) von der BAM auf der Grundlage des Niedersächsischen Dichtungserlasses“ erteilt. Vor ungefähr 10 Jahren wurde die BAM mit dem Erscheinen der Deponieverordnung (DepV) mit der Zulassung von Geokunststoffen, Polymeren und Dichtungskontrollsystemen beauftragt. Wir möchten dies zum Anlass nehmen, an dieser Stelle den viele ehrenamtlichen Experten des Fachbeirats und seiner Arbeitsgruppen für ihren Einsatz und die Unterstützung zu danken. Darüber hinaus soll über aktuelle Arbeitsthemen und Entwicklungen im Fachbeirat berichtet werden. So wurde in einer Sondersitzung des Fachbeirats über die Entlassung aus der Nachsorgephase beim Einsatz von Geokunststoffprodukten in Böschungen diskutiert. Die Unterarbeitsgruppe Fremdüberwachung in der Produktion hat getagt. Darüber hinaus werden Änderungen in den Zulassungsrichtlinien für Kunststoffdichtungsbahnen, Kunststoff-Dränelemente und Geogitter kurz vorgestellt. T2 - 29. Karlsruhe Deponie- und Altlastenseminar CY - Karlsruhe, Germany DA - 16.10.2019 KW - Kunststoffdichtungsbahnen KW - Deponie KW - Geokunststoffe PY - 2019 SN - 978-3-939662-25-9 VL - 36 SP - 15 EP - 28 PB - ICP Eigenverlag Bauen und Umwelt CY - Karlsruhe AN - OPUS4-49321 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Egloffstein, T. ED - Burkhardt, G. T1 - Aktuelles aus der Arbeit des BAM-Fachbeirats N2 - Der Fachbeirat kommt bereits seit 13 Jahren in seiner jetzigen Form zusammen, um Zulassungsrichtlinien, weitere Dokumente und fachliche Fragestellungen zu beraten. Die Zeit bringt auch personelle Veränderungen mit sich, darüber wollen wir berichten. Derzeit wird die Zulassungsrichtlinie für Schutzschichten im Fachbeirat und in seiner Arbeitsgruppe Geotextilien und Kunststoff Dränelemente (AG Geotextilien) überarbeitet. Zudem wurde die Zulassungsrichtlinie für Kunststoffdichtungsbahnen auf den aktuellen Stand der Regelsetzung und Normung gebracht. Bestimmte Medien, die hier bei einigen Prüfungen verwendet werden, dürfen nicht mehr in der EU in Verkehr gebracht werden. Hier werden die Hintergründe und Zusammenhänge in Kürze aufgezeigt. Zuletzt wird die Diskussion in Bezug auf den Einsatz von Rezyklaten in den zugelassenen Produkten aufgeführt. T2 - Karlsruher Deponie- und Altlastenseminar 2022 CY - Karlsruhe, Germany DA - 19.10.2022 KW - Deponie KW - Abdichtungssystem KW - Schutzschichten PY - 2022 SN - 978-3-939662-31-0 VL - 42 SP - 23 EP - 32 PB - ICP Eigenverlag Bauen und Umwelt CY - Karlsruhe AN - OPUS4-56209 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Al-Akel, S. T1 - Die Spannungsrissbeständigkeit von Kunststoffdichtungsbahnen aus PE-HD und die Zulassungsrichtlinie für Schutzschichten N2 - Kunststoffdichtungsbahnen (KDB) aus PE-HD (Polyethylen hoher Dichte) werden häufig zur Abdichtung von Bauwerken in der Geotechnik verwendet. Diese Produkte werden aus einem Kunststoff mit relativ komplexer Zusammensetzung hergestellt. Um eine Aussage über die Haltbarkeit von KDB aus PE-HD treffen zu können, muss das Materialverhalten berücksichtigt werden. In diesem Zusammenhang sind die wichtigsten Aspekte der Dauerhaftigkeit die Spannungsrissbeständigkeit und die Beständigkeit gegen Oxidation. Verschiedene PE-Sorten weisen eine unterschiedliche Spannungsrissbeständigkeit auf. Um dieser Eigenschaft von PE-HD zu begegnen, werden nur KDB aus sehr hochwertigen Rohstoffen zugelassen. Auf der anderen Seite werden hohe Anforderungen an die umgebenden Schichten, wie Auflager und Schutzschicht gestellt, um möglichst geringe Spannungen zu erzeugen und damit Dehnungen die Dehnungen der KDB gering zu halten. Bestimmte Medien, die bei den betreffenden Prüfungen verwendet werden, dürfen nicht mehr in der EU in Verkehr gebracht werden. Im Folgenden sollen die Zusammenhänge in Kürze dargestellt werden. Darüber hinaus sollen Diskussionen und Änderungen der Zulassungsrichtlinie für Schutzschichten im und durch den Fachbeirat vorgestellt werden. T2 - 19. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 14.03.2023 KW - Spannungsrissbeständigkeit KW - Deponie KW - Kunststoffdichtungsbahn PY - 2023 SN - 978-3-943443-53-0 VL - 19 SP - 25 EP - 32 PB - PRESSEL Digitaler Produktionsdruck AN - OPUS4-57194 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Leers, K. A1 - Herzel, Hannes A1 - Emter, J. A1 - Brey, C. A1 - Leimkötter, D. A1 - Künstler, J. A1 - Arnold, U. A1 - Burkhardt, J. A1 - Adam, Christian T1 - Untersuchungen zur agronomischen Wirksamkeit des R-Rhenania Phosphats aus der ersten großtechnischen Anlage N2 - Aufgrund ihrer Phosphorgehalte bieten Klärschlammaschen (KSA) Potentiale für die Herstellung von Phosphatdüngern. Da die agronomische Wirksamkeit von KSA häufig gering ist, bedarf es einer Aufbereitung. Diese kann sowohl vor oder während der Verbrennung des Klärschlamms als auch nachgeschaltet durch eine Aufbereitung der KSA erfolgen. Mit dem nachgeschalteten, thermochemischen AshDec® Verfahren können unter Hinzugabe eines Natrium-Additivs bereits wirksame aschebasierte Düngerprodukte aus KSA hergestellt werden. Im Rahmen des BMBF-Projekts „R-Rhenania“ wurde auf dieser Basis ein thermochemisches Verfahren für eine Rostfeuerung entwickelt, bei dem die Zugabe des Natrium-Additivs direkt bei der Klärschlammverbrennung erfolgt. So sollen die hochwirksamen aschebasierten Dünger direkt bei der Klärschlammverbrennung entstehen (R-Rhenania-Prozess). Der Vergleich von Produkten aus beiden Prozessen (R-Rhenania und nachgeschaltetes AshDec Verfahren) zeigt, dass die chemische Zusammensetzung vergleichbar ist. In Versuchskampagnen in der Monoverbrennungsanlage der Firma Emter GmbH in Altenstadt (Oberbayern) konnte gezeigt werden, dass die Phosphatlöslichkeit in neutraler Ammoniumcitratlösung (PNAC-Löslichkeit) der R-Rhenania Produkte von der Dosierung des Natrium-Additivs abhängt. Am Standort Altenstadt korreliert eine Konzentration von über 8 Gew.-% Na im Produkt mit einer relativen PNAC-Löslichkeit von mindestens 80 % und eine vollständige Löslichkeit mit einem Na-Gehalt von 10,5 Gew.-% Na. Beim Einsatz von R-Rhenania Produkten als P-Dünger für Sommerweizen konnte eine hohe agronomische Wirksamkeit nachgewiesen werden. In den Gefäßversuchen zeigte sich zudem ein Zusammenhang zwischen der PNAC-Löslichkeit und der Düngerwirksamkeit, wobei diese Wirksamkeit der Produkte mit zunehmender Löslichkeit anstieg. Während die Wirksamkeit unbehandelter KSA vergleichbar war zu einer ungedüngten Kontrollvariante, erwiesen sich R-Rhenania Produkte mit einer PNAC-Löslichkeit von mehr als 80 % als besonders effektiv. Die Düngewirkung bei diesen Produkten war sowohl vergleichbar zu einem AshDec-Produkt als auch zu einem konventionellen, wasserlöslichen P-Düngemittel. Auf Grund der erfolgreichen Prozessentwicklung und der nachgewiesenen agronomischen Wirksamkeit der Produkte, wurde am Standort Altenstadt das thermochemische R-Rhenania-Verfahren in die vorhandene Klärschlammmonoverbrennungsanlage integriert. Ab dem Sommer 2024 können dort 15.000 t/a R-Rhenania Dünger hergestellt werden. T2 - Berliner Klärschlamm Konferenz CY - Berlin, Germany DA - 11.11.2024 KW - Phosphor KW - Recycling KW - Dünger KW - Monoverbrennung KW - Klärschlamm PY - 2024 SN - 978-3-911006-83-5 SP - 316 EP - 328 PB - Thomé-Kozmiensky Verlag GmbH CY - Neuruppin AN - OPUS4-61907 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hamann, Christopher A1 - Adam, Christian A1 - Stolle, Dirk A1 - Spanka, M. A1 - Auer, G. T1 - Thermochemical treatment of waste products from iron and steel production N2 - Blast furnace (BF) sludge and electric arc furnace (EAF) dust are typical wastes that incur from iron and steel production. In addition to iron, calcium, carbon, and silicon they usually contain high concentrations of heavy metals such as zinc, lead, and cadmium that are potentially hazardous to the environment, rendering disposal in landfills ecologically problematic and costly. Consequently, pyrometallurgical, hydrometallurgical, and hybrid methods for selective elimination of non-ferrous heavy metals from BF sludge and EAF dust have been conceived, of which only the carbothermic reduction route taken in the so-called Waelz rotary kiln process has been proven to be economically successful. However, this process has several drawbacks regarding efficiency of heavy-metal removal and recovery of iron, and it does not allow processing of BF sludge. In this study, we investigated the efficiency and feasibility of selective chlorination and evaporation of non-ferrous heavy metals, particularly zinc and lead, in both BF sludge and EAF dust as an alternative, thermochemical processing route. To this end, hydrochloric acid and iron(II) chloride solution have been used as chlorinating agents, and the process of heavy-metal chlorination and evaporation has been investigated under inert operating conditions, at variable chlorine concentrations, and at temperatures between 500 and 1200 °C. High zinc and lead removal efficiencies of > 99.5 % were achieved with both chlorinating agents, but iron(II) chloride turned out to be overall more efficient for removal of zinc and lead from BF sludge and EAF dust. Interestingly, and in contrast to previous studies, the iron was completely retained in the processed solid residue, therefore rendering the processed residues virtually zinc- and lead-free raw materials that may either be used internally (e.g., feeding processed BF sludge and EAF dust back into the respective furnaces) or externally (e.g., for cement production). T2 - European Metallurgical Conference 2019 CY - Düsseldorf, Germany DA - 23.06.2019 KW - Blast furnace sludge KW - Electric arc furnace dust KW - Recycling KW - Selective chlorination KW - Zinc PY - 2019 SN - 978-3-940276-89-6 VL - 3 SP - 1267 EP - 1282 PB - GDMB CY - Clausthal-Zellerfeld AN - OPUS4-48362 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Themen aus der Arbeit des Fachbeirats der BAM N2 - Es wird über aktuelle Arbeitsthemen und Entwicklungen im Fachbeirat berichtet. So wurde in einer Sondersitzung des Fachbeirats über die Entlassung aus der Nachsorgephase beim Einsatz von Geokunststoffprodukten in Böschungen diskutiert. Die Unterarbeitsgruppe Fremdüberwachung in der Produktion hat getagt. Darüber hinaus werden Änderungen in den Zulassungsrichtlinien für Kunststoffdichtungsbahnen, Kunststoff-Dränelemente und für die Fremdüberwachung kurz vorgestellt. T2 - 16. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 03.03.2020 KW - Deponie KW - Geogitter KW - Kunststoffdichtungsbahn PY - 2020 SN - 978-3-943443-49-3 VL - 16 SP - 35 EP - 43 PB - HTWK Leipzig CY - Leipzig AN - OPUS4-50507 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian A1 - Herzel, Hannes A1 - Wittwer, Philipp A1 - Leube, Peter A1 - Adam, Christian T1 - Per- und polyfluorierte Alkylsubstanzen (PFAS) während der Klärschlammverbrennung – Analytische Methoden zur Überwachung N2 - Per- and polyfluoroalkyl substances (PFAS) are a group of more than 12,000 anionic cationic, zwitterionic and neutral anthropologic substances which have been used extensively in a variety of products and industries due to their lipo- and hydrophobic properties, and inert physical and chemical stability. As a result of continuous use of fluorinated consumer products, effluents and sewage sludge from wastewater treatment plants (WWTPs) have been shown to be an important source of PFAS contamination into the environment. While environmental exposure of organic pollutants like PFAS, pesticides and pharmaceuticals have to be avoided, phosphorus from sewage sludge must be used in Germany among other things to produce high-quality P-fertilizers for a circular economy. However, the fate of legacy and emerging PFAS compounds during sewage sludge incineration or pyrolysis is for the most parts still unknown. In particular, PFAS analysis in exhaust air from industrial facilities has not yet been standardized in Germany, which means that no comparable results are available for possible regulation. T2 - Berliner Klärschlamm Konferenz CY - Berlin, Germany DA - 11.11.2024 KW - Klärschlamm KW - Per- and Polyfluoroalkyl substances (PFAS) PY - 2024 SN - 978-3-911006-83-5 SP - 230 EP - 241 PB - Thomé-Kozmiensky Verlag GmbH CY - Neuruppin AN - OPUS4-61627 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adamczyk, Burkart A1 - Schraut, Katharina A1 - Adam, Christian ED - Thiel, S. ED - Thomé-Kozmiensky, E. ED - Friedrich, B. ED - Pretz, T. ED - Quicker, P. ED - Senk, D. G. ED - Wortruba, H. T1 - Nachbehandlung von Stahlwerksschlacken und deren Verwertung als Klinkermaterial T1 - Post-treatment of steelmaking slags and their utilisation as cement clinker N2 - Steelmaking slags produced using the Linz-Donawitz method (LD slags) are widely used as building and construction materials in road, earth and water works. Because the legal conditions become more and more re-strictive , this application is uncertain in the future. LD slags contain high amounts of mineral bound iron (in form of Fe2O3), which must be considered as a waste of resources. Except for the Iron the chemical composition is quite similar to that of Portland cement clinker. However, due to the high content of Fe2O3 the mineralogical composition differs significantly, resulting in a low hydraulic reactivity. A post-treatment of the liquid LD slag in an electric arc furnace under reducing conditions enables the reduction of the iron compounds to metallic iron, which separates from the mineral phase due to its higher density. The remaining solidified mineral fraction mainly contains typical crystalline phases of cement clinker in similar ratios: Alite (Ca3SiO5; > 60%) as main phase, Belite (Ca2SiO4, 10%), Tricalciumaluminate (Ca3Al2O6; 5%) and Brownmillerite (Ca2(Al,Fe)2O5, 1%) as secondary phases. Alite, which usually decomposes to Belite and free lime under slow cooling conditions, is stabilized in the Fe-reduced slag probably by integration of foreign ions into the lattice and is stable even if the slag is cooled down very slowly. Furthermore, the particularly large Alite crystals do not exhibit the typical decomposition edge of Belite and lime, found in Alite from ordinary ce-ment clinker. Technological tests for building materials show a high hydraulic reactivity and a compressive strength after 28 days comparable or even slightly higher to reference cement. Nevertheless, because of the increasing viscosity with decreasing Fe2O3 content, the treatment requires a temperature higher than the slag decanted from the LD converter. Furthermore, during the reduction of the bound Iron huge amounts of carbon monoxide are released, resulting in foaming of the slag. Both aspects make it difficult to manage the process. In addition, for economic reasons the treatment has to be carried out immediately after casting the slag from the LD converter to avoid the solidification, which is a logistical challenge for most steel plants. Otherwise the separation of the mineral bound iron as metallic phase and the utilisation of the mineral fraction as cement clinker will both save resources and lower the global CO2-output. For these reasons further initiatives should be considered in the medium term. N2 - LD-Schlacken weisen eine große chemische Ähnlichkeit zu Protlandzementklinker auf. Sie enthalten jedoch noch bis zu 30% Eisen, das mineralisch in oxidischer Form gebunden vorliegt. Dadurch kann sich bei der Erstarrung die wichtigste Klinkerphase "Alit" nicht ausbilden. Durch eine reduzierende Schmelzbehandlung der Schlacke kann des mineralisch gebundene Eisen als Metall separiert werden. Dadurch wird auch die Mineralogie der Schlacke so verändert, dass auch sie nun praktisch einem Portlandzementklinker entspricht. Entsprechende Versuche wurden am kleintechnischen Lichtbogenofen der BAM durchgeführt. Es werden Ergebnisse vorgestellt und auf Grenzen und Möglichkeiten eines derartigen Prozesses im Hinblick auf eine industrielle Umsetzung eingegangen. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 11.06.2018 KW - Zementklinker KW - Stahlwerksschlacke KW - LD-Schlacke KW - Lichtbogenofen KW - Alit PY - 2018 SN - 978-3-944310-41-1 VL - 5 SP - 282 EP - 296 PB - Thomé-Kozmiensky Verlag GmbH CY - Neuruppin AN - OPUS4-45199 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ostermann, Markus A1 - Herzel, Hannes A1 - Adam, Christian A1 - Kühn, A. A1 - Wedell, R. A1 - Mory, D. T1 - Integrierte Systeme (RFA und LIBS) zur Düngemittelgewinnung und zum Management der Bodenfruchtbarkeit N2 - Aufgrund der natürlichen und vom Menschen verursachten Heterogenität von Böden erfordert der Erhalt und die Verbesserung ihrer Fruchtbarkeit durch landwirtschaftliche Bewirtschaftungsmaßnahmen sorgfältig geplante Ent-scheidungen, die auf einer detaillierten Erfassung der Bodeneigenschaften und einem vertieften Verständnis der Bodenprozesse beruhen. Es ist bekannt, dass die konventionelle, flächen-einheitliche Bewirtschaftung Ertragsver-luste durch zu geringe Bewirtschaftungsintensität (z. B. Düngung) auf einen Teil der Fläche verursacht, während andere Teile des Feldes zu hohe Dosen erhalten und es dadurch zu Verschwendung von Ressourcen und zu Um-weltbelastungen kommt. Trotz der Verfügbarkeit von Technologien für ortsspezifische Düngung ist die Akzeptanz ortsspezifischer Bewirtschaftung (Precision Agriculture) in der Praxis noch gering. Ein wesentlicher Grund dafür ist das Fehlen von kostengünstigen Methoden zur Erfassung der bewirtschaftungsrelevanten Bodenmerkmale. So-wohl für die elementanalytische Untersuchung von Böden als auch für die Untersuchung von Ausgangsmaterialien (z.B. Klärschlammaschen) für ihre Verwendung als Dünger ist eine zuverlässige Analytik und Prozessüberwachung erforderlich. T2 - 11. Kolloquium Arbeitskreis Prozessanalytik CY - Wien, Austria DA - 30.11.2015 KW - LIBS KW - Online-RFA KW - Düngemittelgewinnung KW - Bodenfruchtbarkeit KW - BONARES PY - 2015 SP - 23 EP - 24 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-38843 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Egloffstein, Thomas ED - Burkhardt, Gerd T1 - Zum Spannungsrissverhalten von PE-HD Kunststoffdichtungsbahnen und zu aktuellen Themen aus dem Fachbeirat der BAM N2 - Kunststoffdichtungsbahnen (KDB) aus PE-HD (Polyethylen hoher Dichte) werden häufig zur Abdichtung von Bauwerken in der Geotechnik verwendet. Diese Produkte werden aus einem Kunststoff mit relativ komplexer Zusammensetzung hergestellt. Um eine Aussage über die Haltbarkeit von KDB aus PE-HD treffen zu können, muss das Materialverhalten berücksichtigt werden. In diesem Zusammenhang sind die wichtigsten Aspekte der Dauerhaftigkeit die Spannungsrissbeständigkeit und die Beständigkeit gegen Oxidation. Verschiedene PE-Sorten weisen eine unterschiedliche Spannungsrissbeständigkeit auf. Um dieser Eigenschaft von PE-HD zu begegnen, werden nur KDB aus sehr hochwertigen Rohstoffen zugelassen. Auf der anderen Seite werden hohe Anforderungen an die umgebenden Schichten, wie Auflager und Schutzschicht gestellt, um möglichst geringe Spannungen zu erzeugen und damit Dehnungen die Dehnungen der KDB gering zu halten. Bestimmte Medien, die bei den betreffenden Prüfungen verwendet werden, dürfen nicht mehr in der EU in Verkehr gebracht werden. Im Folgenden sollen die Zusammenhänge in Kürze dargestellt werden. Darüber hinaus sollen Diskussionen und Änderungen im Zusammenhang mit der Zulassungsrichtlinie für KDB vorgestellt werden. Der aktuelle Stand der Diskussion im Zusammenhang mit den verwendeten Tensiden in Bezug auf die Spannungsrissprüfung und weiterer Prüfungen wird aufgezeigt. Änderungen der Fremdprüfung von sogenannten Sandschutzmatten, des Standards zur Qualitätsüberwachung (SQÜ) von Kunststoff Dränelementen (KDE) und der Anpassung der Formulierungen zum Überbau der in Abdichtungen verwendeten Produkte werden in Kürze aufgezeigt. T2 - Karlsruher Deponie- und Altlastenseminar 2023 CY - Karlsruhe, Germany DA - 18.10.2023 KW - Spannungsrissbeständigkeit KW - Deponie KW - Kunststoffdichtungsbahn PY - 2023 SN - 978-3-939662-33-4 VL - 44 SP - 17 PB - ICP Eigenverlag Bauen und Umwelt CY - Karlsruhe AN - OPUS4-58633 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa A1 - Adam, Christian A1 - Montag, D. A1 - Ehm, J.H. T1 - Schwankungen der P-Gehalte in Klärschlämmen im Kontext der Klärschlammverordnung N2 - Ab 2029 gilt für alle Kläranlagen in Deutschland eine Pflicht zur Rückgewinnung von Phosphor (P) aus Klärschlamm. Ausgenommen sind nur Anlagen mit Schlämmen mit weniger als 20 g P/kg bezogen auf die Trockenmasse (TM). Für eine Überprüfung der Phosphorschwankungen im Klärschlamm wurden neun verschiedene Kläranlagen ausgewählt mit Phosphorgehalten nahe der "Rückgewinnungsgrenze" von 20 g/kg TM. Der entwässerte Klärschlamm dieser Anlagen wurde monatlich beprobt und auf seinen Phosphorgehalt geprüft. Die Phosphorschwankungen betrugen je nach Anlage zwischen 4 % und 13 % (relative Standardabweichung), im Mittel rund 7 %. T2 - KlärschlammTage CY - Online Meeting DA - 09.06.2021 KW - Phosphor KW - Klärschlamm KW - Phosphorrückgewinnung KW - Abwasserbehandlung KW - Klärschlammverordnung PY - 2021 SP - 102 EP - 108 PB - Deutsche Vereinigung für Wasserwirtschaft, Abwasser und Abfall e. V. (DWA) CY - Hennef AN - OPUS4-52839 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa A1 - Adam, Christian A1 - Montag, D. A1 - Barjenbruch, M. ED - Holm, O. ED - Quicker, P. ED - Kopp-Assenmacher, S. T1 - Nährstoffrückgewinnung aus Klärschlamm: Eine Betrachtung zukünftiger Verwertungsszenarien für Deutschland N2 - Agricultural sewage sludge utilization becomes less important in Germany. In 2017, new fertilizer and waste laws caused the agricultural sewage sludge utilization to collapse by more than a quarter. From 2029, in German wastewater treatment plants (WWTPs) phosphorus (P) must be recovered from sewage sludge ifit contains more than 2 wt % P. Agricultural utilization will be prohibited for large WWTPs > 100,000 population equivalents (pe) from 2029 and > 50,000 pe from 2032. In Germany, each federal state must annually report amounts and quality of agriculturally utilized sewage sludge which was 17 % of the total disposal in 2019. The reports of 10 States were evaluated for 2016 and 2017 representing approx. 60 % ofthe total agriculturally used sludge volume. Whereas phosphorus recovery is mandatory this does not apply to other nutrients. However, many P recovery processes recover other nutrients, too. Considering three differentscenariosfor future German sewage sludge disposal Shows that 70 - 77 % ofthe P load in sewage sludge will probably be recovered in the future. At the same time, this applies for about 0 - 16 % of nitrogen, 36 - 52 % of calcium, 31-53 % of potassium, and 40 - 52 % of magnesium. However, these recovered nutrient loads can substitute only 1 % or less ofthe commercial fertilizer demand except from phosphorus which is about 45 % ofthe demand. T2 - Berliner Klärschlammkonferenz CY - Berlin, Germany DA - 15.11.2021 KW - Phosphor KW - Klärschlamm KW - Phosphorrückgewinnung KW - Landwirtschaftliche Klärschlammverwertung KW - Klärschlammverordnung PY - 2021 SN - 978-3-944310-56-5 VL - 4 SP - 252 EP - 265 PB - Thomé-Kozmiensky-Verlag GmbH CY - Neuruppin AN - OPUS4-54117 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Al-Akel, S. T1 - Aktuelle Diskussion aus dem Fachbeirat der BAM N2 - Das Jahr 2020 war vor allen Dingen von der Pandemie geprägt, die alle Bereiche des Lebens und Arbeitens beeinflusst hat und immer noch beeinflusst. Dies hat sich auch auf verschiedene Maßnahmen im Zusammenhang mit zugelassenen Produkten ausgewirkt. In diesem Zusammenhang sollen die Punkte kurz aufgeführt werden. Des Weiteren soll aufgezeigt werden, wie bei der Bearbeitung der Richtlinien, der Zulassungstätigkeit und Beurteilung der Produkte an der BAM und im Fachbeirat vorgegangen wird. Darüber hinaus soll noch einmal kurz auf die Entlassung aus der Nachsorgephase eingegangen werden. Am Ende sollen verschiedene aktuelle Fragestellungen des Fachbeirat aufgezeigt werden. T2 - 17. Leipziger Deponiefachtagung CY - Online meeting DA - 02.03.2021 KW - Deponie KW - Geokunststoffe KW - Kunststoffdichtungsbahn PY - 2021 SN - 978-3-943443-50-9 VL - 17. SP - 31 CY - Leipzig AN - OPUS4-52212 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Hobohm, J. A1 - Kuchta, K. A1 - van Wasen, Sebastian A1 - Krüger, Oliver T1 - Recovery of rare earth elements - optimized elemental analysis of fluorescent lamp shredder waste N2 - Rare earth elements (REE) are a crucial component of fluorescence lamps. Several procedures have been developed to recovery these technological important elements. Nevertheless, actual REE recycling from fluorescence lamps is scarce so far (recovery rate of less than 1 %), with current recycling approaches concentrating on glass recovery. Since most recycling processes include several, also wet-chemical steps, a complete knowledge of the actual elemental composition of the respective mass flows is necessary for an efficient REE recovery. We tested seven different reagent mixtures for microwave-assisted digestion of fluorescent lamp shredder, including HF, HClO4, and H2O2. We determined the concentrations of 25 of the most relevant rare earth and other trace elements in the respective dilutions. Two independent digestions, one a mixture of perchlorid/nitric/hydrofluoric acid and the other aqua regia, showed the highest concentrations of 23 of these elements, excluding only Sn and Tb. The REE concentrations in the tested lamp shredder sample (stated in g/kg) were 10.2 (Y), 12.1 (La), 7.77 (Ce), 6.91 (Eu), 1.90 (Gd), and 4.11 (Tb). T2 - 5th International conference industrial and hazardous waste management - Crete 2016 CY - Chania, Crete, Greece DA - 27.09.2016 KW - Rare earth elements KW - Critical raw materials KW - Resource recovery KW - WEEE PY - 2016 SN - 978-960-8475-20-5 SN - 2241-3138 SP - 1 EP - 4 AN - OPUS4-37761 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas A1 - Müller, Werner ED - Egglofstein, T.A. ED - Burkhardt, G. T1 - Aktuelles aus dem Fachbeirat der BAM und von der Zulassungsstelle N2 - Unser Beitrag soll auch in diesem Jahr über aktuelle Diskussionsthemen und Fragestellungen im Fachbeirat der BAM, in seinen Arbeitsgruppen und in der BAM informieren. Im vergangenen Jahr wurde intensiv über die Qualitätssicherung und den Einbau von Kunststoff-Dränelementen diskutiert. In diesem Zusammenhang wurde ein Untersuchungsprogramm zum Einfluss von Überlappstößen auf das Wasserableitvermögen von Kunststoff-Dränelementen angestoßen. Die Ergebnisse sollen hier in Kürze vorgestellt und die Bedeutung für die Abminderungsfaktoren und damit für die Bemessung erläutert werden. Zu welchem Zeitpunkt muss ein Kunststoff Dränelement überbaut werden und welche weiteren Regelungen müssen hier beachtet werden? Was steckt eigentlich hinter diesen strengen Regelungen? Diese Fragen sollen im Folgenden diskutiert werden. Die Deponieverordnung (DepV) fordert eine Akkreditierung der fremdprüfenden Stellen nach verschiedenen Normen. Die fachlichen Anforderungen an den „Fremdprüfer-Kunststoff“ legt die Richtlinie Fremdprüfer der BAM fest. Um diese Anforderungen im Akkreditierungsprozess ausreichend berücksichtigen zu können, wurde nun eine sogenannte DAkkS Regel erarbeitet, die die Anforderungen der Richtlinie spiegelt. Über den aktuellen Stand soll berichtet werden. Auch über die aktuelle Arbeit in Zusammenhang mit den Kunststoffdichtungsbahnen (KDB) soll berichtet werden. Der Prüfhinweis B14 (Bestimmung der Maßhaltigkeit von geosynthetischen Dichtungsbahnen aus Polyethylen hoher Dichte (PEHD)) wurde überarbeitet. Vorangegangen war eine intensive Entwicklung der Prüfeinrichtung sowie ausgiebige Ringversuche im AK GWS (Arbeitskreis Grundwasserschutz). In diesem Zusammenhang wurden neue Anforderungen an die Produkte gestellt. Die Hintergründe dazu sollen kurz vorgestellt werden. Die DVS (Deutscher Verband für Schweißen und verwandte Verfahren) Richtlinie 2225-4 regelt das Schweißen der KDB auf der Deponiebaustelle. Werden KDB im strukturierten Bereich miteinander verschweißt, werden die Strukturen in der Regel vorher abgetragen. Die DVS Richtlinie 2225-4 sieht unter bestimmten Voraussetzungen von einem Abtragen der Strukturen ab. Vor diesem Hintergrund wurde vom AK GWS ein Untersuchungsprogramm initiiert, das die Auswirkungen aufzeigen soll. Die Ergebnisse und Schlussfolgerungen werden vorgestellt. Die europäischen Anwendungsnormen und das deutsche Straßenbaumerkblatt für Geokunststoffe verwenden statistische Begriffe. Deren nur „beiläufige“ Erwähnung lässt jedoch offen, was genau im Zusammenhang gemeint ist. Produkte unterschiedlicher Hersteller können daher trotz gleicher Angaben zu den Mindestwerten in den Leistungserklärungen oder Datenblättern deutlich unterschiedliche Eigenschaften haben. Um vorschriftsmäßig bemessen zu können, muss man jedoch wissen, was sich hinter den Zahlen verbirgt. Eine Zulassung oder Zertifizierung ist nur dann sinnvoll, wenn darüber hinaus einheitlich definiert wird, was die Angaben für die werkseigene Produktionskontrolle, die Inspektion durch benannte Stellen und die Kontrolle durch Dritte bedeuten. In den vergangenen Jahren seit 2009 wurde versucht, die Zulassungen stärker auf die Vorgaben aus der europäischen Normung zu stützen. Daher musste nun diskutiert werden, welche statistische Bedeutung die Angaben in den Zulassungen für Kunststoff-Dränelementen und Geotextilien zum Filtern und Trennen haben. Hier musste eine einheitliche Regelung getroffen werden. Über die Ergebnisse soll berichtet werden. T2 - 26. Karlsruher Deponie- und Altlastenseminar CY - Karlsruhe, Germany DA - 19.10.2016 KW - Deponieabdichtunssysteme KW - Schweißen KW - Kunststoffdichtungsbahnen PY - 2016 SN - 978-3-939662-19-8 SP - 61 EP - 75 PB - ICP Eigenverlag Bauen und Umwelt CY - Karlsruhe AN - OPUS4-38018 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Werner A1 - Tarnowski, C. A1 - Wöhlecke, Andreas A1 - Zanzinger, H. ED - Kelsey, C. T1 - The "Zero Leakage" approach for landfill liner and capping systems N2 - An approach to achieve “zero leakage” is discussed with respect to the experience in Germany, where strict regulations for landfill lining and capping systems have been developed and issued because of large environmental problems related to landfills that accumulated in the 1970’s and 1980’s. Using a thick, high quality HDPE geomembrane (GMB), which is installed free of residual waves and wrinkles in intimate contact with a compacted clay liner (CCL) or geosynthetic clay liner (GCL) of very low permeability, by a qualified, experienced, well equipped and properly third-party controlled installer and which are protected by heavy protection layers designed with respect to long-term performance of the GMB, may result in a liner or capping system of practically no leakage. This is demonstrated by analyzing results of measurements obtained from permanently installed leak detection systems in combination with HDPE GMBs. The survey is based on 32 German landfills with 1,276,500 m² of installed HDPE GMB. T2 - GeoAmericas 2016 - 3rd Pan-American Conference on Geosynthtics CY - Miami Beach, FL, USA DA - 10.04.2016 KW - Geomembanes KW - Installation KW - Welding KW - Quality management PY - 2016 SN - 978-0-9884772-2-3 VL - 1 SP - 441 EP - 453 PB - Minerva - Technology, Resources, and Information CY - Jupiter, Florida, USA AN - OPUS4-36499 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herzel, Hannes A1 - Leimkötter, D. A1 - Hermann, L. A1 - Emter, J. A1 - Brey, C. A1 - Künstler, J. A1 - Hartmann, S. A1 - Krannich, G. A1 - Moggert, N. A1 - Kurz, P. A1 - Eder, C. A1 - Grimm, B. A1 - Adam, Christian ED - Holm, O. ED - Thomé-Kozmiensky, E. ED - Quicker, P. ED - Kopp-Assenmacher, S. T1 - Success-Story CaNaPO4: Erfolgreiche REACH Registrierung und Inbetriebnahme großtechnischer Anlagen N2 - The Sewage Sludge Ordinance (AbfKlärV), which was amended in 2017, obligate the recovery of phosphorus from sewage sludge and sewage sludge ash from 2029 and 2032, respectively. Thermal disposal of sewage sludge has established itself as the preferred method of disposal, and the capacities of mono-incineration plants are being continuously expanded. Plants for phosphorus recovery, on the other hand, are currently still mainly in the construction, piloting, or commissioning phase. It is estimated that the plant capacities for P recovery planned today will not even be able to cover a quarter of the volume of these ashes in 2029. Therefore, temporary storage of the remaining ashes is currently being discussed to retrieve it later and process it in the P recovery plants, which will then be sufficiently available. It is currently unclear how such interim or long-term storage (> 1 year) should be organized. In addition to legal (fee) issues, the assessment of the technical feasibility of retrievability and the phosphorus recovery potential of landfilled ash remains open. The Institute of Environmental Engineering (ISA) at RWTH Aachen University and the Federal Institute for Materials Research and Testing (BAM) are jointly investigating five deposited ashes that have been dug out and were provided by three landfill operators. The investigations focus on the physical and chemical characterization of these landfilled ashes and its P recovery potential during treatment in thermochemical and wet chemical processes. These results are evaluated in comparison with “fresh,” i.e., non-landfilled sewage sludge ash samples of comparable origin in order to determine the influence of storage. T2 - Berliner Klärschlamm Konferenz CY - Berlin, Germany DA - 11.11.2025 KW - Phosphor KW - Recycling KW - Thermochemisch KW - Dünger KW - Großtechnik PY - 2025 SN - 978-3-911006-63-7 VL - 8 SP - 236 EP - 256 PB - Thomé-Kozmiensky Verlag GmbH CY - Neuruppin AN - OPUS4-64833 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Themen aus dem Fachbeirat der BAM N2 - Die Anforderungen an Geokunststoffprodukte und deren Qualitätssicherung unterliegen einem stetigen Wandel, der sowohl durch technische Veränderungen als auch durch normative und organisatorische Entwicklungen geprägt ist. Insbesondere der Fachbeirat der BAM gemäß Deponieverordnung (DepV) spielt hier im Bereich der Deponietechnik eine wichtige Rolle. An dieser Stelle sollen aktuelle Themen aus dem Fachbeirat der BAM vorgestellt werden, die wesentliche Änderungen in der Zulassungs- und Anwendungspraxis betreffen. Der Beitrag beleuchtet unter anderem Veränderungen innerhalb der BAM, die Modernisierung der Publikationsformate sowie die fachliche Weiterentwicklung der Zulassungsrichtlinien. Besondere Aufmerksamkeit gilt der Diskussion um die Einbauhilfe im Schutzschichtsystem, der Einführung einer europäischen Zugversuchsnorm für Kunststoffdichtungsbahnen sowie der Fremdüberwachung der Produktion geosynthetischer Komponenten. Darüber hinaus werden neue Anforderungen an Edelstahlelektroden in Dichtungskontrollsystemen und die Spannungsrissbeständigkeit von PE-HD-Dichtungsbahnen thematisiert. T2 - 35. Karlsruher Deponie- und Altlastenseminar CY - Karlsruhe, Germany DA - 15.10.2025 KW - Deponie PY - 2025 VL - 48 SP - 26 EP - 35 PB - ICP AN - OPUS4-64408 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin A1 - Adam, Christian ED - Martins, Isabel ED - Ulsen, Carina ED - Angulo, Sergio Cirelli T1 - Secondary building materials from construction and demolition waste: environmental benefits and costs N2 - Due to the large quantities of construction and demolition waste (CDW) in Europe, its reuse or recycling is of particular importance. Although several countries already recycle high amounts of CDW, the use as secondary raw materials is often limited by inferior building material properties. Specific characteristics, like high porosity and low density are caused by hardened cement paste in crushed concrete and the content of mortar and plaster in brick debris. Impurities like wood or gypsum and also harmful substances like organic pollutants may be a major problem for a reuse and should be minimized. Therefore unwanted materials and impairing substances have to be separated from the secondary building material stream. This can be done during the demolition process by using techniques for selective dismantling or during the subsequent treatment of the resulting rubble. Since almost all processing steps are associated with environmental impacts, the benefits of saving natural resources by applying secondary building materials should be weighed carefully. An environmental performance evaluation was undertaken to assess different techniques for reducing gypsum in recycled concrete aggregates, aiming at a minimization of elutable sulfates. These results were compared to the environmental impacts of the extraction of natural aggregates for concrete. T2 - "Progress of recycling in the built environment" CY - Sao Paulo, Brazil DA - 03.08.2015 KW - CDW processing KW - Demolition/selective dismantling KW - Gypsum KW - Environmental evaluation KW - Bauschuttaufbereitung KW - Ökobilanzielle Bewertung PY - 2015 UR - http://www.rilem.org/gene/main.php?base=500218&id_publication=449&id_papier=10699 SN - e-ISBN: 978-2-35158-158-2 SP - 192 EP - 199 CY - Paris, France AN - OPUS4-38170 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, S. A1 - Herzel, Hannes A1 - Adam, Christian A1 - Montag, D. ED - Holm, O. ED - Thomé-Kozmiensky, E. ED - Quicker, P. ED - Kopp-Assenmacher, S. T1 - Langzeitlagerung von Klärschlammaschen ab 2029? Erste Erfahrungen zur Phosphorrückgewinnung aus deponierten Klärschlammverbrennungsaschen N2 - Das Institut für Siedlungswasserwirtschaft (ISA) der RWTH Aachen University sowie die Bundesanstalt für Materialforschung und -prüfung (BAM) untersuchen gemeinsam fünf deponierte KSA, die von drei Deponiebetreibern ausgebaut und zur Verfügung gestellt wurden sind. Im Fokus der Untersuchungen stehen die physikalische und chemische Charakterisierung der deponierten KSA sowie deren P-Rückgewinnungspotenzial bei der Behandlung in thermochemischen sowie nasschemischen Verfahren. Diese Ergebnisse werden im Vergleich mit „frischen“, also nicht deponierten KSA-Proben vergleichbarer Herkunft bewertet, um so den Einfluss der Lagerung auf die KSA zu erfassen. T2 - Berliner Klärschlamm Konferenz CY - Berlin, Germany DA - 11.11.2025 KW - Klärschlammasche KW - Recycling KW - Deponie KW - Monoverbrennung PY - 2025 SN - 978-3-911006-63-7 VL - 8 SP - 192 EP - 202 PB - Thomé-Kozmiensky Verlag GmbH CY - Neuruppin AN - OPUS4-65017 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Joachim A1 - Adamczyk, Burkart A1 - Ebert, Dominik A1 - Ehrenberg, Andreas A1 - Schraut, Katharina A1 - Algermissen, David A1 - Adam, Christian T1 - Usage of BOF slag and next generation EAF slag in the cement industry N2 - When the transformation of its production routes, which the European steel industry aims to complete within the next two decades, is accomplished, increased amounts of EAF slag will be generated. In most cases the BF/BOF production route is intended to be substituted by a DRI/EAF combination. But in some cases only the BF will be substituted by a DRI/SAF (smelter) combination and the BOF process remains. Then BOF slags will remain, too. BAM and FEhS cooperate together with further research and industry partners in two research projects dealing on the one hand with the utilisation of modified BOF slag as a cement clinker substitute ("SlagCEM") and on the other hand with the use of modified and granulated EAF slag as granulated blast furnace slag (GBS) substitute ("DRI-EOS"). T2 - 9th International Slag Valorisation Symposium CY - Leuven, Belgium DA - 08.04.2025 KW - Steel slags KW - Basic oxygen furnace (BOF) KW - Electric arc furnace (EAF) KW - Cement KW - Slag valorisation PY - 2025 SP - 187 EP - 191 AN - OPUS4-64713 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Gorbushina, Anna A1 - Plarre, Rüdiger A1 - Stephan, Ina T1 - Umweltsimulation an der BAM – Grundlegende Ansätze mit Beispielen aus der natürlichen Umwelt N2 - Drei grundlegend verschiedene Ansätze für Umweltsimulation werden an Beispielen illustriert: (i) Ganzheitlicher Ansatz - Nachstellen von Umweltmilieus im Labor Ziel ist hier das Nachstellen von (kombinierten) Umweltbedingungen im Labor; die Umweltparameter werden mit all ihren Wechselwirkungen aufgebracht. Hauptnutzen ist eine gegenüber der natürlichen Beanspruchung erhöhte Reproduzierbarkeit der Umweltbedingungen. Hat man sein Laborsetup entwickelt, ist es auf verschiedene Materialien anwendbar. Unter solchen Laborbedingungen ermittelte Lebensdauern sind dabei nicht auf die typischerweise sehr variablen Real-Umweltbedingungen übertragbar. (ii) Parametrisierter Ansatz - Ermittlung einzelner Materialempfindlichkeiten Hierbei werden im Labor die Wirkungen separater Umweltparameter auf Materialien nachgestellt. Für eine solche Separation der Einflussfaktoren ist insbesondere die Aufschlüsselung möglicher Wechselwirkungen der Umwelt-parameter (z.B. Mikroklima an bestrahlten Oberflächen) erforderlich. Einzelne (meist Alterungs-) Empfindlichkeiten können qualitativ nachgewiesen werden oder sogar – als Beanspruchungs-Wirkungs-Funktionen – quantifiziert werden, was einen wesentlichen Schritt in Richtung der Digitalisierung der Material¬prüfung darstellt. Insbesondere ist dann auch eine Lebensdauer-vorhersage für vorgegebene Zeitreihen der Beanspruchungs¬parameter umsetzbar. (iii) Rückwirkungen auf die Umwelt Umweltbeanspruchungen können zur Freisetzung von Schadstoffen in die Umwelt führen. Durch die Nachstellung kritischer, aber realitätsnaher Einsatzszenarien kann die Menge an freigesetzten Substanzen abgeschätzt werden. Egal, welcher Ansatz verfolgt wird – ein Vergleich mit der oder einer Real-beanspruchung ist unerlässlich, ebenso wie die Messdatenaufzeichnung (data logging) aller potenziell relevanten Beanspruchungsparameter während dieser Realbeanspruchung. Obwohl die naturnahe Umwelt – sowohl in der BAM als auch bei der GUS – gegenüber der technischen Umwelt eher untergeordnet auftritt, werden zur Illustration Beispiele aus der naturnahen Umwelt verwendet. T2 - 50. Jahrestagung der GUS CY - Online meeting DA - 23.03.2022 KW - Umweltsimulation PY - 2022 SN - 978-3-9818507-7-2 SP - 79 EP - 89 AN - OPUS4-55015 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Raedel, Martina A1 - Feldmann, Ines A1 - Bücker, Michael A1 - Kömmling, Anja ED - Roemich, Hannelore ED - Fair, Lauren T1 - Testing bulked adhesives for the Restoration of Stained-Glass Windows N2 - In this study, bulked adhesives were examined regarding changes in properties for their use in the restoration of stained-glass windows. Two epoxy adhesives commonly used in the restoration of flat glass, Araldite® 2020 and Hxtal NYL-1™, were investigated. The adhesives were mixed with various silica-based micro- and nano-particles as fillers. Different tests were carried out on the adhesives with and without fillers in order to characterise their chemical and mechanical properties. The tests included colorimetry, dynamic-mechanical methods of analysis and tests on bending strength. No property changes could be ascertained in the bulked adhesives that would be negative for the restoration of delicate flat glass. T2 - Recent advances in glass and ceramics - ICOM-CC Glass and Ceramics Working Group Interim Meeting CY - Breslau / Wroclaw, Poland DA - 25.05.2016 KW - bulked epoxy adhesives KW - micro-fillers KW - nano-fillers PY - 2016 SN - 978-83-64419-80-5 SP - 155 EP - 163 AN - OPUS4-36457 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Falkenhagen, Jana T1 - Combined impact of UV radiation and nitric acid (HNO3) on HDPE jerrycans – comparison of outdoor and lab test N2 - A damaging action of HNO3-55% only occurs in combination with its decomposition into nitrous gases, which can be caused by UV radiation. In a laboratory test, transparent HDPE jerrycans have been exposed to both UV radiation and 55 wt-% nitric acid solution at (41 ± 2)°C, for up to 20 days. For comparison, UV radiant exposure (21 days) and nitric acid exposure (up to 6 weeks) were performed separately, at nearly equal temperatures. The respective damages are compared with FTIR spectroscopy in ATR and HT-gel permeation chromatography (GPC) on a molecular level and with hydraulic internal pressure testing as a component test. For the used jerrycans, relevant oxidation can only be found after the combined exposure. The gradual increase in oxidative damage shows the good reproducibility of the lab exposure. The decomposition of nitric acid into nitrous gases by UV radiation – as well as the jerrycan oxidation – is also observed at lower HNO3 concentration (28 wt- %). Similar results are obtained after outdoor tests. Again, the damage occurs only after combined exposure, in contrast to the exposures to UV only and to HNO3 only, which were conducted in parallel. Outdoor exposures are most readily accepted as they represent possible end-use conditions. However, the reproducibility of these exposures is poor due to the large temporal variations in weather. There are also several safety risks, which is why the number of replicates remains limited. Since the outdoor and lab exposure tests show the same qualitative results, it is appropriate to conduct systematic studies in the laboratory. After 6 days of lab exposure, the oxidation damage is rated as critical, which corresponds to about 1/10 year in Central Europe, according to the UV radiant exposure. It should be noted that this amount can also occur in two sunny weeks. T2 - 24th iapri World Packaging Conference CY - Valencia, Spain DA - 17.06.2024 KW - Ppolyethylene KW - UV exposure KW - Nitric acid KW - Oxidation PY - 2024 VL - 2 SP - 30 EP - 37 PB - ITENE AN - OPUS4-60414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Schraut, Katharina A1 - Adamczyk, Burkart A1 - Weimann, Karin A1 - Gluth, Gregor T1 - Erzeugung klimaschonender Bindemittel als Alternativen zu Zement durch thermochemische Behandlung von mineralischen Nebenprodukten und Abfällen N2 - Die Zementindustrie erzeugt etwa 6-7% der globalen CO2-Emissionen und steht damit als Industriezweig vor dem Hintergrund einer anvisierten Klimaneutralität vor gewaltigen Herausforderungen. Der Prozess der Klinkerherstellung wurde über die vergangenen Jahrzehnte bereits kontinuierlich optimiert. Seit 1990 ist es der deutschen Zementindustrie gelungen, die spezifischen CO2-Emissionen der Zementproduktion u. a. durch den Einsatz alternativer, nicht fossiler Brennstoffe und durch Absenkung des Klinkergehalts im Zement um 20 % zu senken. Weitere konventionelle Minderungsstrategien versprechen jedoch nur noch wenig zusätzliche Reduktion. Im Falle des Portlandklinkers besteht die Schwierigkeit darin, dass zwei Drittel der CO2-Emissionen rohstoffbedingt durch die Entsäuerung des Kalksteins (CaCO3) anfallen, die durch die beschriebenen Maßnahmen nicht weiter abgesenkt werden können. Vielmehr wird es erforderlich sein, noch zu entwickelnde oder zu optimierende Technologien anzuwenden und ggf. alle relevanten Ebenen wie Produktion, Weiterverarbeitung und Anwendung von Zement und Beton neu zu denken. Neben technologischen Ansätzen zur CO2-Abscheidung mit nachfolgender langfristiger Speicherung (Carbon Capture and Storage – CCS) oder Verwertung (Carbon Capture and Utilisation – CCU) werden auch alternative Rohstoffe für die Zementproduktion und alternative Bindemittel in Betracht zu ziehen sein. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 25.04.2022 KW - Zement KW - Sekundärrohstoff PY - 2022 SN - 978-3-944310-58-9 SP - 372 EP - 385 PB - TK-Verlag CY - Neuruppin AN - OPUS4-54737 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -