TY - JOUR A1 - Kalbe, Ute A1 - Bandow, Nicole A1 - Holm, Olaf A1 - Simon, Franz-Georg T1 - Elutionsverhalten der Produkte eines alternativen Verfahrens zur Aufbereitung von HMVA N2 - Im Rahmen eines ZIM-geförderten Projektes wurde eine nass-mechanische Aufbereitung von Hausmüllverbrennungsasche (HMVA) hinsichtlich der Mengen und der Qualitäten generierter Fraktionen optimiert. Dabei standen besonders die Qualitäten der mineralischen Fraktionen, die mengenmäßig den größten Anteil darstellen, im Vordergrund, da sie für einen möglichen Einsatz als Baustoff nutzbar gemacht werden sollen. Insbesondere die Chlorid- und Sulfatgehalte sollten dafür reduziert werden. Durch die BAM wurde im Projekt u. a. die Freisetzung von umweltrelevanten Stoffen in den mineralischen Fraktionen untersucht. Dafür wurden Schütteleluate als Übereinstimmungstest und Eluate aus Lysimeterversuchen im Labormaßstab zur Bewertung des Langzeitverhaltens auf ihre Inhaltsstoffe analysiert. KW - Elutionsverhalten KW - HMVA KW - Ersatzbaustoff KW - Lysimeter PY - 2016 SN - 0039-2162 VL - 67 IS - 8 SP - 619 EP - 623 PB - Kirschbaum Verlag CY - Bonn AN - OPUS4-37213 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fortini, Renata A1 - Meyer-Plath, A. A1 - Kehren, D. A1 - Gernert, U. A1 - Agudo Jácome, Leonardo A1 - Sturm, Heinz T1 - Measurement of flexural rigidity of multi-walled carbon nanotubes by Dynamic Scanning Electron Microscopy N2 - In this work the flexural rigidity of individual large diameter multi-walled carbon nanotubes (MWCNTs) was investigated. The bending modulus were obtained by detecting the resonance frequencies of mechanically excited cantilevered carbon nanotubes using the so-called dynamic scanning electron microscopy technique, and applying the Euler–Bernoulli beam theory. For the nanotubes studied, we determined a modulus of up to 160 GPa. This agrees with values reported by other authors for MWCNTs produced by catalytic chemical vapor deposition, however, it is 6-8 times smaller than values reported for single and multi-walled carbon nanotubes produced by arc-discharge synthesis. Toxicological studies with carbon nanotubes have been showing that inhaled airborne nanofibers that reach the deep airways of the respiratory system may lead to serious, asbestos-like lung diseases. These studies suggested that their toxicity critically depends on the fiber flexural rigidity, with high rigidity causing cell lesions. To complement the correlation between observed toxicological effects and fiber rigidities, reliable and routinely applicable measurement techniques for the flexural rigidity of nanofibers are required. KW - Flexural rigidity KW - Bending modulus KW - Resonance frequency KW - Carbon nanotubes KW - Fiber toxicology PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-514190 DO - https://doi.org/10.3390/fib8050031 SN - 2079-6439 VL - 8 IS - 5 SP - 31 PB - MDPI AN - OPUS4-51419 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hoffmann, Holger A1 - Baldofski, Stefanie A1 - Hoffmann, Kristin A1 - Flemig, Sabine A1 - Silva, C. P. A1 - Esteves, V. I. A1 - Emmerling, Franziska A1 - Panne, Ulrich A1 - Schneider, Rudolf T1 - Structural considerations on the selectivity of an immunoassay for sulfamethoxazole N2 - Sulfamethoxazol (SMX),a sulfonamide, is a widely used bacteriostatic antibiotic and therefore a promising marker for the entry of anthropogenic Pollution in the environment. SMX is frequently found in wastewater and surface water. This study presents the production of high affinity and selective polyclonal antibodies for SMX and the development and Evaluation of a direct competitive enzyme-linked immunosorbent assay(ELISA)for the quantification of SMX in environmental watersamples. The crystal structures of the cross-reacting compounds sulfamethizole, N4-acetyl-SMX andsuccinimidyl-SMX were determined by x-ray diffraction aiming to explain their high cross-reactivity. These crystal structures are described for the first time. The quantification range of the ELISA is 0.82–63 µg/L. To verify our results, the SMX concentration in 20 environmental samples,including wastewater and surfacewater,was determined by ELISA and tandem mass spectrometry(MS/MS).A good Agreement of the measured SMX concentrations was found with average recoveries of 97–113%for the results of ELISA compared to LC-MS/MS. KW - X-Ray diffraction KW - ELISA KW - LC-MS/MS KW - Sulfamethoxazole PY - 2016 DO - https://doi.org/10.1016/j.talanta.2016.05.049 SN - 0039-9140 SN - 1873-3573 IS - 158 SP - 198 EP - 207 PB - Elsevier B.V. CY - Amsterdam, Netherlands AN - OPUS4-38530 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dudziak, Mateusz A1 - Bhatia, Riya A1 - Dey, R. A1 - Falkenhagen, Jana A1 - Ullrich, M. S. A1 - Thomsen, C. A1 - Schartel, Bernhard T1 - Wastewater phosphorus enriched algae as a sustainable flame retardant in polylactide N2 - Revolutionizing our polymer industry for adaption to a sustainable carbon circular economy has become one of today’s most demanding challenges. Exploiting renewable resources to replace fossil-fuel—based plastics with biopolymers such as poly(lactic acid) (PLA) is inevitable while using waste streams as a raw material resource at least is promising. When it comes to using PLA as technical polymer, its high flammability must be addressed by flame retardants compatible with the thermoplastic processing of PLA and its compostability. This study proposes microalgae enriched with phosphorus from wastewater (P-Algae) as an elegant way towards a kind of sustainable organophosphorus flame retardant. The concept is demonstrated by investigating the processing, pyrolysis, flammability, and fire behavior of PLA/P-Algae, while varying the P-Algae content and comparing P-Algae with four alternative bio-fillers (phosphorylated lignin, biochar, thermally treated sewage sludge, and metal phytate) with different P-contents as meaningful benchmarks. KW - PLA KW - Flame Retardancy KW - Phosphorylated Algae KW - Wastewater flame retardants KW - Zink phytate KW - Phosphorylated lignin KW - Thermally treated sludge PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-604150 DO - https://doi.org/10.1016/j.polymdegradstab.2024.110885 SN - 1873-2321 SN - 0141-3910 VL - 227 SP - 1 EP - 11 PB - Elsevier Ltd. AN - OPUS4-60415 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nicolicea, Alberto A1 - Oliveros-Mata, E. A1 - Makarov, D. A1 - Melzer, Michael A1 - Pelkner, Matthias A1 - Zabila, Y. T1 - Flexible anisotropic magnetoresistive sensors for novel magnetic flux leakage testing capabilities N2 - Rigid magnetic field sensors such as anisot Hall sensors have been used for years and have become industry standard for electromagnetic non-destructive testing (NDT). Recent technological developments in the field of flexible electronics allow for the fabrication of reshapeable magnetic field sensors on flexible substrates via thin-film deposition or printing. The magnetic properties of these sensors have comparable characteristics to industry-standard rigid magnetic field sensors, with the added ability of adapting to the surface of complex components and scanning in contact with the sample surface. This improves defect detectability and magnetic signal strength by minimizing the scanning lift-off (LO) distance. In this article flexible AMR sensors mounted on a rotative mechanical holder were used to scan a semi-circular ferromagnetic sample with 3 reference defects via magnetic flux leakage (MFL) testing, thus demonstrating the applicability of this type of sensors for the scanning of curved samples. In order to benchmark the performance of these sensors in comparison to industry standard rigid magnetic field sensors, a ferromagnetic sample with 10 reference defects of different depths was scanned employing flexible AMR and rigid GMR sensors. Defects with depths ranging from 110 μm up to 2240 μm were detected with an signal-tonoise ratio (SNR) of 2.7 up to 27.9 (for flexible AMR sensors) and 6.2 up to 72.3 (for rigid GMR sensors), respectively. A 2D magnetometer mapping of the sample with a spatial scanning step of 10 × 50 μm2 (flexible AMR) and 16 × 100 μm2 (rigid GMR) was obtained. The results show that this type of sensor can be used for high-resolution and high-detail mapping of defects on the surface of planar and non-planar ferromagnetic samples since the scanning lift-off distance is equal to the substrate thickness of 20 μm for in-contact scanning. The SNR comparison between flexible and rigid sensors shows that the performance of the flexible AMR sensors employed is not very far behind the performance of the rigid GMR sensors used. KW - Flexible magnetic field sensors KW - Non-destructive testing KW - Magnetic flux leakage KW - Thin film sensor fabrication KW - Defect detection PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-603931 DO - https://doi.org/10.1016/j.ndteint.2024.103160 VL - 146 SP - 1 EP - 15 PB - Elsevier Ltd. AN - OPUS4-60393 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Simon, Franz-Georg A1 - Vogel, Christian A1 - Kalbe, Ute T1 - Antimony and vanadium in incineration bottom ash – leaching behavior and conclusions for treatment processes N2 - Due to its large mineral fraction, incineration bottom ash (IBA) from municipal solid waste incineration is an interesting raw material that can be used for road construction or to produce secondary building materials. However, leaching chloride, sulfate, and potentially harmful heavy metals may cause problems in using IBA in civil engineering. Investigating leaching behavior is crucial for the assessment of the environmental compatibility of IBA applications. Various test procedures are available for that purpose. In the present study, a long-term leaching test of a wet-mechanically treated IBA was performed in a lysimeter for almost six years. While concentrations of chloride, sulfate and the majority of the heavy metals started to decrease rapidly with progressive liquid-to-solid ratio (L/S), antimony (Sb) and vanadium (V) behaved differently. At the beginning of the lysimeter test, the Sb and V concentrations were low, but after approximately one year of operation at an L/S ratio of around 0.8 L/kg, a steady increase was observed. It was shown that this increase is the result of low Ca concentrations due to the formation of CaCO3. With the data, the solubility products from Ca-antimonate and Ca-vanadate were calculated. The unusual leaching behavior of Sb and V should be kept in mind when considering field scenarios and evaluating the impact on the environment. KW - Bottom ash KW - Lysimeter KW - Leaching of waste materials KW - Secondary building materials PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-534317 DO - https://doi.org/10.31025/2611-4135/2021.15115 SN - 2611-4135 VL - 16 SP - 75 EP - 81 PB - CISA CY - Padua AN - OPUS4-53431 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Simon, Franz-Georg A1 - Haas, Marco A1 - Pienkoß, Fabian A1 - Kwiatkowski, Robert T1 - Wet-mechanical treatment: Processing of bituminous road construction waste in a jigging machine N2 - Jigging machines are used in processing technology in many areas. Examples are the processing of coal, ores, and primary and secondary raw and waste materials. Even small differences in density are offen sufficient for successful sorting. In the work presented here, milled material from road construction waste contaminated with bitumen is to be separated from uncontaminated material. In this way, scarce landfill space could be saved and mineral material be returned to the material cycle. KW - Wet-mechanical treatment KW - Jig KW - Road construction waste PY - 2023 UR - https://www.at-minerals.com/de/artikel/aufbereitung-von-bitumenhaltigem-strassenaufbruch-in-einer-setzmaschine-4037512.html SN - 1434-9302 VL - 64 IS - 12 SP - 46 EP - 51 PB - Bauverlag BV GmbH CY - Gütersloh AN - OPUS4-59160 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Roesch, Philipp A1 - Vogel, Christian A1 - Kalbe, Ute A1 - Simon, Franz-Georg T1 - Entwicklung von PFAS-Summenparametern mittels Combustion Ion Chroma- tography (CIC) N2 - Wie können industriell synthetisierte Schadstoffe aus einer Stoffklasse quantifiziert werden, deren genauer Umfang unbekannt ist und auf mehrere tausend Verbindungen geschätzt wird? Im Falle der per- und polyfluorierten alkylierten Substanzen (PFAS) stellen sich Wissenschaftler*innen weltweit seit über zehn Jahren diese Frage. Neben der etablierten Methodik der Einzelstoffanalytik (engl. target analytic) existieren Summenparameteranalysen zur Quantifizierung organisch gebundener fluorierter Verbindungen in Umweltmedien und Konsumprodukten. An der Bundesanstalt für Materialforschung und -prüfung (BAM) beschäftigen wir uns mit der Weiterentwicklung von Summenparametermethoden am Beispiel von PFAS-belasteten Umweltkompartimenten wie Böden, Klärschlämmen und Gewässerproben sowie PFAS-haltigen Konsumgütern. In diesem Beitrag stellen wir zwei ausgewählte Fallbeispiele vor und diskutieren die Vor- und Nachteile der Methoden im Vergleich zur Einzelstoffanalytik. KW - PFAS KW - Combustion Ion Chromatography KW - LC-MS/MS KW - Water analysis KW - Environmental analysis KW - Sum parameter analysis PY - 2023 SN - 1618-3258 VL - 29 IS - 2 SP - 40 EP - 44 AN - OPUS4-57611 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gehrmann, H.-J. A1 - Hiebel, M. A1 - Simon, Franz-Georg T1 - Methods for the Evaluation of Waste Treatment Processes N2 - Decision makers for waste management are confronted with the problem of selecting the most economic, environmental, and socially acceptable waste treatment process. This paper elucidates evaluation methods for waste treatment processes for the comparison of ecological and economic aspects such as material flow analysis, statistical entropy analysis, energetic and exergetic assessment, cumulative energy demand, and life cycle assessment.The work is based on the VDI guideline 3925. A comparison of two thermal waste treatment plants with different process designs and energy recovery systems was performed with the described evaluation methods. The results are mainly influenced by the type of energy recovery, where the waste-to-energy plant providing district heat and process steam emerged to be beneficial in most aspects. Material recovery options from waste incineration were evaluated according to sustainability targets, such as saving of resources and environmental protection. KW - Material flow analysis KW - Life cycle assessment KW - Cumulative energy demand KW - Cost benefit analysis KW - Eco-efficiency analysis PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-426455 UR - https://www.hindawi.com/journals/je/2017/3567865/ DO - https://doi.org/10.1155/2017/3567865 SN - 2314-4912 VL - 2017 SP - Article ID 3567865-1 EP - 13 PB - Hindawi CY - London AN - OPUS4-42645 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gleis, Markus A1 - Simon, Franz-Georg T1 - Schwermetallbelastung und Behandlung von Aschen aus Abfallverbrennungsanlagen N2 - Die Thermische Abfallbehandlung in Abfallverbrennungsanlagen sorgt für eine Inertisierung des Restmülls bei gleichzeitiger Minimierung von abgas- und abwasserseitigen Emissionen. Da der Großteil der Rückstände in verwertbare Sekundärprodukte überführt wird, fördert die thermische Abfallbehandlung die Verwirklichung einer Circular Economy in Europa. KW - Rostasche KW - Circular Economy KW - Ersatzbaustoffe PY - 2021 SN - 1436-9095 VL - 23 IS - 3 SP - 48 EP - 52 PB - Springer Vieweg CY - Wiesbaden AN - OPUS4-52344 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -