TY - CONF A1 - Rhode, Michael A1 - Kannengießer, Thomas A1 - Erxleben, Kjell A1 - Kaiser, Sebastian T1 - Kurzvorstellung des DVGW-geförderten Projektes “H2SuD” - Einfluss des Schweißens auf die Wasserstoffaufnahme und Degradation im Betrieb befindlicher H2-Gasleitungen N2 - Die Wasserstoffinfrastruktur ist eine zentraler Bestandteil der erfolgreichen Umsetzung der wasserstoffbasierten Energiewende. Dabei bilden Ferngasleitungen quasi das "Rückgrat" der Transportinfrastruktur großer Gasmengen. Dabei müssen unter Umständen Reparaturen an den Pipelines durchgeführt werden. Dabei ist in der Erdgasinfrastruktur das Schweißen an in Betrieb befindlichen (d.h. von Gas durchflossenen) Pipelines Stand der Technik. Es ist jedoch vollkommen offen, inwieweit diese Technik auf die reine Wasserstoffpipelines übertragbar sind. Hierzu leistet das Projekt H2SuD wichtige Beiträge zur Aufklärung des Einfluss eines Reparaturschweißprozesses auf die Wasserstoffaufnahme und Degradation im Betrieb befindlicher H2 Gasleitungen. T2 - Sitzung des Unterarbeitskreises / UAK 2.1.1 "Rohrleitungen" im Rahmen der Normungsroadmap Wasserstofftechnologien CY - Online meeting DA - 16.06.2023 KW - Wasserstoff KW - Schweißen KW - Pipeline KW - Reparatur KW - Prüfverfahren PY - 2023 AN - OPUS4-57714 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael A1 - Kannengießer, Thomas T1 - Welding (and joining) technologies for the hydrogen economy - a short overview N2 - This study gives an overview on the important field of joining processes for component fabrication in hydrogen technologies. The current main issues and future perspectives are highlighted for the different technological field of hydrogen generation, storage, transport and use. In addition, the emerging field of additive manufacturing is included. Some remarks are given for standardization and regulations. T2 - Meeting of the European Welding Association (EWA), Executive Committee (EC) 1 CY - Frankfurt am Main, Germany DA - 22.03.2023 KW - Hydrogen KW - Welding KW - Research KW - Study PY - 2023 AN - OPUS4-57222 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pirskawetz, Stephan T1 - Richtlinie „Detektion von Spanndrahtbrüchen mit Schallemission“ N2 - Ein großer Teil unserer Brücken wurden in den 1950er bis 1970er Jahren als Spannbetonbrücken gebaut. Mit der damals noch relativ jungen Technologie entstanden elegante, teilweise gewagte Bauwerke mit großen Spannweiten, welche die Vorteile der Materialien Stahl und Beton geschickt kombinieren. Die Standsicherheit einiger dieser Brücken ist heute gefährdet. Die Ursachen liegen in der enorm gewachsenen Belastung durch Schwerverkehr, teilweise ungenügender Wartung und in konstruktiven und Materialschwächen, die der mangelnden Erfahrung mit der Technologie in der Bauzeit geschuldet sind. Ein neuralgischer Punkt der Bauwerke sind die in den Beton integrierten Spannglieder. Infolge von Korrosion und Ermüdung können Elemente der Spannglieder reißen, wodurch die für das Tragwerk notwendige Spannung und somit die Tragfähigkeit reduziert werden. Nicht bei allen Brücken kündigen sichtbare Risse im Beton oder auffällige Verformungen den Tragfähigkeitsverlust bzw. das finale Versagen rechtzeitig an. Die Schallemissionsanalyse ist die derzeit einzige Methode, das Reißen einzelner Spannstähle zuverlässig und mit wirtschaftlich vertretbarem Aufwand zu detektieren. Trotzdem es schon einige Spannbetonbauwerke gibt, die mit Schallemissionsanalyse überwacht werden, ist das Verfahren noch wenig bekannt. Außerdem fehlen technische Richtlinien, was die Ausschreibung und Vergabe von entsprechenden Aufträgen und die Bewertung der Angebote sehr erschwert. Um sowohl Baulastträger als auch Dienstleistungsanbieter in den Vergabeverfahren und im Betrieb der Monitoringsysteme zu unterstützen, hat sich eine Gruppe von Experten aus den Bereichen Bauingenieurwesen und Schallemission zum Entwurf einer Richtlinie „Detektion von Spanndrahtbrüchen mit Schallemission“ zusammengefunden. Mit diesem Beitrag wird die Richtlinie vorgestellt, deren Bearbeitung bis zur SCHALL 23 abgeschlossen sein soll. T2 - SCHALL 23 Entwicklung und Anwendung der Schallemissionsanalyse und Zustandsüberwachung mit geführten Wellen CY - Wetzlar, Germany DA - 21.03.2023 KW - Spannbeton KW - Brücke KW - Spannstahlbruch KW - Schallemission KW - Richtlinie PY - 2023 AN - OPUS4-57391 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neitsch, Marcel T1 - Nutzung von Recycling-Kunststoffen für die Produktion von Gefahrgutverpackungen – aktueller Stand der Norm ISO 16103 N2 - Im Vortrag wird der Stand der Weiterentwicklung der ISO 16103 dargestellt, in der Regelungen zur Qualitätssicherung bei der Herstellung von Recycling-Kunststoffen und daraus hergestellter Gefahrgutverpackungen enthalten sind. Darüber hinaus wird auf die Verbindungen zu den UN Model Regulations und zum ADR eingegangen und welche Konsequenzen sich daraus für die Zulassung und die Anerkennung des Qualitätssicherungsprogramms ergeben. T2 - 19. Gefahrgut-Technik-Tage CY - Berlin, Germany DA - 16.11.2023 KW - ISO 16103 KW - Recycling-Kunststoffe KW - Gefahrgutverpackungen PY - 2023 AN - OPUS4-58894 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Thoralf A1 - Ebell, Gino T1 - Grundlagen der Korrosion N2 - Durch das alkalische Milieu des Porenwassers im Beton ist der Stahl normalerweise dauerhaft vor Korrosion geschützt. Unter ungünstigen Umgebungsbedingungen (Chlorideintrag, Carbonatisierung) kann die passive Deckschicht auf der Stahloberfläche zerstört werden. Der Korrosionsprozess ist initiiert. Die entstehenden Korrosionsprodukte werden zunächst vom Porengefüge des Betons aufgenommen, ohne dass es zu sichtbaren Schäden am Bauwerk führt. Im fortgeschrittenem Stadium der Korrosion können sich dann Risse und Abplatzungen bilden. Um notwendige Sanierungsmaßnahmen sowohl aus sicherheitstechnischen Gründen als auch aus wirtschaftlichen Erwägungen rechtzeitig einzuleiten, sind frühzeitige und weitestgehend zerstörungsfreie Prüfverfahren zur Ermittlung der aktuellen Korrosionswahrscheinlichkeit der Stahlbewehrung von großer Bedeutung. Deshalb finden Methoden und Verfahren zur laufenden bzw. regelmäßigen Korrosionsüberwachung von Stahlbetonbauwerken ständig größere Beachtung, sowohl im Bereich Forschung und Entwicklung als auch in der Praxis. Die elektrochemische Potentialfeldmessung ist ein etabliertes und weit verbreitetes Verfahren zur Beurteilung des Korrosionszustandes der Bewehrung in Stahlbetonbauwerken. Mit Hilfe dieses Verfahrens können Bereiche korrodierender Bewehrung zerstörungsfrei lokalisiert werden. In der Regel kommt diese Methode bei der Detektion von chloridinduzierter Korrosion zum Einsatz. Der Lehrgang vermittelt den Teilnehmenden in kompakter Form einen zusammenfassenden Überblick über die notwendigen Grundlagen zum Verständnis der Messmethode, der Vorbereitung und Durchführung der Messungen, der notwendigen Begleituntersuchungen sowie der Interpretation der gewonnenen Daten. Der erste Tag ist der theoretischen Ausbildung gewidmet, am zweiten Tag folgt dann die praktische Anwendung der Lerninhalte. Am dritten Tag folgt die Abnahme der praktischen und theoretischen Prüfung zur Erlangung des Sachkundenachweises. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen CY - Berlin, Germany DA - 24.04.2023 KW - Potentialfeldmessung KW - Korrosion PY - 2023 AN - OPUS4-57493 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Thoralf A1 - Burkert, Andreas A1 - Ebell, Gino T1 - Korrosionsschutz-Dauerhaftigkeit als Herausforderung für die Ewigkeit N2 - Technische Infrastruktur umfasst unter anderem Straßen, Brücken, Flughäfen, Telekommunikationsnetze und alle Systeme der Energieversorgung. Alle Anlagen in diesen Bereichen erfordern hohe finanzielle Investitionen und sollen für Jahrzehnte der Nutzung ausgelegt sein. Dieser Anspruch kann nur dann erfüllt werden, wenn die Anlagen und die darin erhaltenen Ausstattungen korrosionssicher ausgelegt werden; d.h. Korrosionsschäden während der Nutzung ausgeschlossen werden können. Es werden Vorschläge für eine sachgerechte Auswahl von Maßnahmen zum Korrosionsschutz in verschiedenen Anwendungsbereichen dargestellt und beachtenswerte Parameter für eine kompetente Gestaltung der Korrosionsschutzmaßnahmen erläutert. T2 - fkss Infotag 02/2023 CY - Berlin, Germany DA - 06.07.2023 KW - Korrosionsschutz KW - Dauerhaftigkeit KW - Korrosionsprüfung KW - Atmosphärische Korrosion PY - 2023 AN - OPUS4-57869 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Thoralf A1 - Burkert, Andreas T1 - Field exposure studies of austenitic and duplex stainless steels in tunnel atmospheres N2 - Due to the high corrosivity that are present in road tunnel structures, cleaning and maintenance work on stainless steel components in the tunnels is carried out at regular intervals in the tunnels, which means that parts of the lanes or the whole tunnel have to be temporarily closed. To reduce these traffic disruptions and maintenance costs, it is important to reduce the work that is needed for cleaning and maintenance of stainless steel components in road tunnels. One possibility is the identification and utilization of better suited alternatives to the commonly used austenitic stainless steels AISI 316L and AISI 316Ti. Thus, a field exposure study was carried out in different road tunnels throughout Germany to qualify different duplex and lean duplex stainless steels for tunnel constructions. The proposed scientific poster gives an overview of results after the first three years of exposure in three different road tunnels. Samples of different stainless steels were placed in different areas of the tunnel – at lane height and at the ceiling. Some samples were exposed under sheltered conditions. Pit depths were evaluated on the free surface and in crevice areas after each year of exposure. The investigations show that duplex stainless steels have a comparable or even better corrosion resistance than austenitic steels in tunnel atmospheres T2 - Stainless Steel World Conference & Expo 2023 CY - Maastricht, Netherlands DA - 26.09.2023 KW - Corrosion KW - Atmosphere KW - Tunnel KW - Stainless Steel PY - 2023 AN - OPUS4-58487 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Thoralf T1 - Kurzbericht aus den DIN Ausschüssen N2 - Der Vortrag gibt einen Überblick über die Tätigkeiten der DIN-Ausschüsse "Korrosionsprüfverfahren" sowie "Korrosion und Korrosionsschutz". Es werden neuste Informationen zum Stand verschiedener Normen aus den beiden Ausschüssen gegeben. T2 - Arbeitskreissitzung des GfKorr-Arbeitskreises Korrosionsuntersuchung und -überwachung CY - Leipzig, Germany DA - 21.03.2023 KW - Korrosion KW - Normung KW - Korrosionsprüfung KW - Korrosionsschutz PY - 2023 AN - OPUS4-57243 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg A1 - Günzel, Stephan T1 - Entwicklungen rings um Gase als Energieträger N2 - Dr. Mair erläutert, welcher Anwuchs an H2-Bedarf zu erwarten ist, wo er weltweit erzeugt werden könnte und in welcher Form auf grünem Wasserstoff basierende Energieträger transportiert werden können. Es wird deutlich, dass das Transportaufkommen von H2 erheblich anwachsen wird und dass sich alle Seiten, die Regelsetzer und die Industrie darauf vorbereiten müssen. Danach wird mit Blick auf die Normungsroadmap H2 des DIN der probabilistische Ansatz mit seinem Potenzial, Normen und Vorschriften in ihrer Wirkung zu simulieren und zu bewerten kurz vorgestellt. Der dritte Block des Vortrages beginnt mit der Definition von Sicherheit, zeigt kurz das mikromechanische Prinzip der Alterung von Composite und greift dann ein Thema auf, dass Dr. Mair bereits 2018 und 2019 in dieser Runde dargelegt hat: Der Aufwand für die klassische Wiederkehrende Prüfung ist enorm und bringt nur wenig Erkenntnis. Es werden graphisch das 5-Jahres 100%-Prooftesting, der Ansatz nach GGR 022 mit seiner zerstörend geprüften Stichprobe und der mögliche Ansatz für eine ergebnisgesteuerte Stichprobenprüfung auf ZfP-Basis miteinander verglichen. Die Unterschiede im Aufwand-zu-Nutzen-Verhältnis sind enorm. Dabei ist der aufwändigste Ansatz zudem der mit der geringsten Erkenntnistiefe. Jeder Ansatz, der von einer 100%-Prüfung in einem maximalen Zeitrahmen von 10 Jahren abweicht, also z.B. der Verzicht auf eine 100%-Prüfung während des Betriebes, würde eine Änderung des Regelwerkes erfordern, die zeitnah angestoßen werden müsste. Da es sich hierbei primär um eine Ressourcenoptimierung und nicht um eine Verbesserung der Sicherheit handelt, liegt der Ball bei den Verbänden. Als eine Idee für das Herangehen mit einer Begrenzung auf Druckgefäße, die nach der EN 17339 zulassungsfähig sind (fest montiert, H2 und nur CFK), verweist Dr. Mair auf die SV 674 in Verbindung mit 6.2.3.5.3/.4 ADR/RID. Bei dem absehbaren Anwachsen des Bestandes an H2-Batteriefahrzeugen, ist hier nicht nur ein Optimierungsaspekt, sondern auch ein Kapazitätsproblem in der wiederkehrenden Prüfung zu lösen. Es würde aber auch ein Mehrwert für die Sicherheit entstehen. T2 - 30. BAM-DIN-IGV-DVFG Treffen CY - Berlin, Germany DA - 22.02.2023 KW - Wasserstoffspeicher KW - Markthochlauf KW - Sicherheit KW - Wiederkehrende Prüfung KW - Schallemissionsanalyse PY - 2023 AN - OPUS4-57041 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maack, Stefan A1 - Niederleithinger, Ernst T1 - Imaging of Ultrasonic Echo Measurements for Reconstruction of Technical Data of Bridges – Possibilities, Limitations and Outlook N2 - When reassessing existing concrete bridges, the challenge is often to obtain missing or incomplete information on the internal structure. In particular, the number and position of the existing reinforcement as well as the geometric dimensions of the components are of interest. Non-destructive testing methods, like radar or ultrasound, which work on the basis of the pulse-echo method, have been established for this purpose, as they only require access to the component from one side. The measurement data recorded on the structure require pre-processing to be able to reproduce the internal structure geometrically accurately. Besides different steps of data processing, the geometrical reconstruction of the measured data based on the Synthetic Aperture Focusing Technique (SAFT) is state of the art today. In this paper, the technical possibilities of the ultrasonic echo method are presented based on measurements in the laboratory and on a real bridge structure. The precision of the reconstruction and its limitations are shown. In addition to the state of the art SAFT technique, open questions and the latest research approaches, such as imaging by reverse time migration (RTM) including initial results are discussed. T2 - 13th German-Japanese Bridge Symposium CY - Osaka, Japan DA - 29.08.2023 KW - Bridge KW - Non destructive testing and evaluation KW - Concrete KW - Validation PY - 2023 AN - OPUS4-58328 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin A1 - Krebber, Katerina T1 - Novel fading suppression method for distributed optical fiber acoustic sensing N2 - A universal method based on alternating pulse widths is proposed to suppress the signal fading for all distributed acoustic sensors (DASs) and experimentally demonstrated by one DAS system based on a Mach-Zehnder interferometer. T2 - Optica Sensing Congress CY - Munich, Germany DA - 30.07.2023 KW - Distributed fiber sensing KW - Acoustic sensing KW - Structural health monitoring KW - Fading suppression PY - 2023 AN - OPUS4-58049 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin T1 - Introduction to group 8.6 N2 - A brief introduction of group 8.6 and the research work on the application of fiber sensing. T2 - DIU Besuch CY - Berlin, Germany DA - 05.05.2023 KW - Structural health monitoring KW - Distributed fiber sensing KW - Distributed acoustic sensing KW - Practical application PY - 2023 AN - OPUS4-57430 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lozano, Daniel A1 - Bulling, Jannis A1 - Gravenkamp, Hauke A1 - Prager, Jens A1 - Birk, Carolin T1 - The SBFEM to simulate the scattering of ultrasonic guided waves interacting with defects in plate structures N2 - In the field of guided waves for non-destructive testing, the interaction of these waves with damages or other discontinuities in a structure is critical. When a guided wave mode travels and hits a defect, it scatters in all directions, converting to other modes and reflecting the existing one. These interactions are captured in scattered far field complex amplitudes. The amplitudes are stored in scattering matrices, which characterise the elastodynamic behaviour of a defect completely. Scattering matrices are also useful to simulate backpropagation from a defect using ray-tracing methods. Simulating these interactions is challenging, and analytical solutions only exist for simple geometries. Still, using general tools like the finite element method results in large, usually costly models. Recently, researchers proposed a method based on a numerical implementation of the Kirchhoff–Helmholtz integral that allows the computation of the scattering matrices using a model containing only the damaged region. However, classical methods to resolve the far field and low-order elements were used, leading to large models yet more efficient than using other techniques. We propose using the SBFEM as an alternative to enhance the computation of the far field scattering. The damaged region is discretised using high-order polyhedral elements, while the far field is constructed using a modified version of the SBFEM. Examples compared to the literature demonstrate the validity of the approach. T2 - Doktorandentreffen CY - Attendorn, Germany DA - 16.10.2023 KW - SBFEM KW - Guided Waves KW - Scattering PY - 2023 AN - OPUS4-59775 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lengas, Nikolaos A1 - Müller, Karsten A1 - Schlick-Hasper, Eva A1 - Neitsch, Marcel A1 - Johann, Sergej A1 - Zehn, M. W. T1 - Improved criteria for evaluating impact targets in regulative drop tests of dangerous goods packagings N2 - For dangerous goods packagings, drop testing onto an essential unyielding target can be used to assess the mechanical resistance to impact loads. Adopted regulations like ADR/RID require that the impact surface provided shall be integral with a mass at least 50 times than that of the heaviest package to be tested. The problem is that many manufacturers do not possess impact targets that satisfy the required 50 times mass ratio for regulative drop tests during series production. The objective of this work is to verify existing and define improved criteria for impact target structures based on systematic investigations. Previous evidence highlights the relevance of other parameters in addition to the mass ratio. Therefore, in this research, a variation of drop test parameters was carried out experimentally. Furthermore, numerical vibration analysis was applied to investigate the deformability of the impact surface. The results conclude that the mass ratio of 1:50 cannot be defined as a decisive criterion. In order to determine the influence of further drop test parameters, the research findings were used to validate a parametric model which assesses impact target deflection. An approximation quality of over 90 % was achieved. As a result, new evaluation criteria are proposed. Firstly, a method for identifying critical impact target designs is provided. Secondly, a new comprehensive formula compares the approximated maximum deflection of a real impact target to the respective theoretical threshold derived from a worst-case assumption. In practice, this leads to great advantages in the evaluation of already installed impact targets for dangerous goods packagings. T2 - 31st IAPRI Members’ conference CY - Mumbai, India DA - 22.05.2023 KW - Drop test KW - Structural dynamics KW - Dangerous goods packagings KW - Impact target KW - Vibration analysis PY - 2023 AN - OPUS4-57715 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann, Jens A1 - Ebell, Gino A1 - Burkert, Andreas T1 - Stahl mit Potenz(t)ial - Duplexstähle im Bauwesen N2 - In diesem Vortrag wird eine Übersicht der gemeinsamen Zusammenarbeit von BAM und Modersohn gegeben. Der Fokus liegt auf dem Thema Duplexstahl. T2 - 50 Jahre Modersohn Jubiläumsveranstaltung - Teil 1 Industriepartner CY - Spenge, Germany DA - 16.06.2023 KW - Korrosion KW - Nichtrostender Stahl KW - KorroPad KW - Auslagerungsversuche KW - Lean Duplex PY - 2023 AN - OPUS4-57817 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann, Jens A1 - Ebell, Gino A1 - Burkert, Andreas T1 - Stahl mit Potenz(t)ial - Duplexstähle im Bauwesen N2 - Der Vortrag enthält eine Übersicht über die gemeinsame Zusammenarbeit der BAM mit Fa. Modersohn der letzten 20 Jahre. Der Fokus liegt dabei auf den Lean Duplex Stählen. T2 - 50 Jahre Modersohn Jubiläumsveranstaltung - Teil 2 Handelspartner CY - Spenge, Germany DA - 17.06.2023 KW - Korrosion KW - Nichtrostender Stahl KW - KorroPad KW - Auslagerungsversuche KW - Lean Duplex PY - 2023 AN - OPUS4-57818 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann, Jens T1 - 1. Sitzung GfKORR AK "Atmosphärische Korrosion" N2 - Eine Übersicht zu den Zielen und Schwerpunktthemen des neu gegründeten Arbeitskreises Atmosphärische Korrosion. T2 - 1. Sitzung des GfKORR Arbeitskreises Atmosphärische Korrosion CY - Online meeting DA - 25.01.2023 KW - Korrosion KW - Atmosphäre KW - Luftqualität KW - Auslagerungsversuche PY - 2023 AN - OPUS4-57022 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan T1 - Guideline on NDT-supported reliability assessment of existing structures N2 - The presentation summarizes the idea and the methodology of the ZfPStatik project and gives insight into three case studies, showing how non-destructive testing results can be utilized beneficially in the recalculation of existing prestressed concrete and reinforced concrete bridges. T2 - 2nd Conference of the European Association on Quality Control of Bridges and Structures – EUROSTRUCT2023 CY - Vienna, Austria DA - 26.09.2023 KW - Reliability KW - Assessment KW - Existing structures KW - Non-destructive testing PY - 2023 AN - OPUS4-58485 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan A1 - Maack, Stefan A1 - Aßmann, Norman A1 - Feistkorn, S. T1 - Ways to unlock the potential of NDT for the reliability assessment of existing structures N2 - Vortrag über die Berechnung von Messunsicherheiten und die POD-Analyse zur Aufbereitung von ZfP-Ergebnissen für die Zuverlässigkeitsbewertung bestehender Bauwerke. T2 - 8th International Workshop on Reliability of NDT/NDE @ SPIE Smart Structures + NDE CY - Los Angeles, CA, USA DA - 12.03.2023 KW - Probability of Detection KW - Measurement uncertainty KW - Reliability assessment PY - 2023 AN - OPUS4-57192 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan A1 - Kainz, C. A1 - Braml, T. T1 - Reliability reassessment of bridges with geometrical NDT results N2 - This presentation summarizes recent developments within the scope of the national pre-standardization project “ZfPStatik”, which aims to prepare a guideline about NDT-supported structural analyses. The focus is on the purposeful and explicit utilization of geometrical tendon and reinforcement bar positions measured on-site in reliability analysis — shown by means of a prestressed concrete bridge as case study. T2 - 13th German Japanese Bridge Symposium CY - Osaka, Japan DA - 28.08.2023 KW - Existing structures KW - Probabilistic methods KW - Data-supported assessment PY - 2023 AN - OPUS4-58268 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühnel, Alena A1 - Stelzner, Ludwig A1 - Weise, Frank T1 - 3D-Ansprache von Betonfahrbahndeckentexturen N2 - Die Oberflächentexturierung der Betonfahrbahndecken mittels Grinding und Grooving steht seit einigen Jahren im Mittelpunkt der Forschung und Entwicklung des Betonstraßenbaus in Deutschland. In den vergangenen Jahren wurden die vorteilhaften Oberflächenperformances derartiger Texturen, wie z.B. Griffigkeit, Ebenheit, Lärmminderung, in zahlreichen Forschungsprojekten umfassend untersucht. Im Kontext des gegenwärtig verfolgten ganzheitlichen performanceorientierten Ansatzes liegt der Fokus nun verstärkt auf der Analyse und Charakterisierung der Oberflächentopografie von Grinding- bzw. Groovingtexturen. Insbesondere gilt ein Hauptaugenmerk hierbei der zeitlichen Entwicklung der Oberflächentexturen in Abhängigkeit von äußeren Einwirkungen durch Klima und Verkehr. Im Rahmen eines von der Bundesanstalt für Straßenwesen (BASt) geförderten Forschungsvorhabens wurden zunächst die messtechnischen Voraussetzungen für eine hochaufgelöste dreidimensionale Erfassung der Oberflächentopografie von Grinding- und Groovingtexturen in situ geschaffen. Das schließt auch die Entwicklung einer Messanordnung, die eine Wiederholbarkeit der 3D-Messungen gewährleistet und somit die Erfassung der zeitlichen Texturveränderungen ermöglicht. Basierend darauf wurden Auswerteroutinen zur qualitativen und quantitativen Beschreibung der Oberflächentexturen und deren Veränderungen entwickelt und angewandt. Anschließend wurde der Zustand von Grinding- und Groovingtexturen an ausgewählten Praxisstrecken in definierten Zeitintervallen erfasst. Unter Verwendung der erarbeiteten Auswerteroutinen wurden die erfassten Oberflächen analysiert und repräsentative Texturkennwerte abgeleitet. T2 - Forschungskolloquium Betonstraßenbau CY - Dresden, Germany DA - 19.01.2023 KW - Betonfahbahndeckentexturen KW - Grinding KW - 3D-Laserscanning KW - Datenanalyse KW - Grooving PY - 2023 AN - OPUS4-56896 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kromm, Arne A1 - Rhode, Michael A1 - Kannengießer, Thomas T1 - Kurzvorstellung des Projektes H2SuD / Wasserstoff und Schweißen Einfluss des Schweißens auf die Wasserstoffaufnahme und Degradation im Betrieb befindlicher H2 Gasleitungen N2 - Die Wasserstoffinfrastruktur ist eine zentraler Bestandteil der erfolgreichen Umsetzung der wasserstoffbasierten Energiewende. Dabei bilden Ferngasleitungen quasi das "Rückgrat" der Transportinfrastruktur großer Gasmengen. Dabei müssen unter Umständen Reparaturen an den Pipelines durchgeführt werden. Dabei ist in der Erdgasinfrastruktur das Schweißen an in Betrieb befindlichen (d.h. von Gas durchflossenen) Pipelines Stand der Technik. Es ist jedoch vollkommen offen, inwieweit diese Technik auf die reine Wasserstoffpipelines übertragbar sind. Hierzu leistet das Projekt H2SuD wichtige Beiträge zur Aufklärung des Einfluss eines Reparaturschweißprozesses auf die Wasserstoffaufnahme und Degradation im Betrieb befindlicher H2 Gasleitungen. T2 - Sitzung des DIN-Gemeinschaftsarbeitsausschusses NA 092 00 05 GA, NAS/NMP: Zerstörende Prüfung von Schweißverbindungen CY - Berlin, Germany DA - 15.03.2023 KW - Wasserstoff KW - Pipeline KW - Reparatur KW - Schweißen PY - 2023 AN - OPUS4-57169 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel A1 - Grasse, Dennis A1 - Seeber, H. A1 - Kluge, Martin A1 - Donner, Marcel T1 - Mild Traumatic Brain Injury - Current Research Works in the Field of Primary Blast Injury N2 - In this presentation, the team security research of division 2.1 informs about current research efforts in the field of traumatic brain injury. The focus lies on the consequences of low-level blast on the human brain. Also the general research approaches of the team for the investigation of the behaviour of shock waves within human tissues are presented. T2 - ATLAS ENTRY Seminar CY - Göppingen, Germany DA - 21.08.2023 KW - LLB KW - Blast KW - mTBI KW - Primary blast injury KW - Traumatic brain injury PY - 2023 AN - OPUS4-58130 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel A1 - Tschirschwitz, Rico A1 - Kluge, Martin T1 - Einsatz von Messtechnik bei Großversuchen N2 - Im Rahmen dieses Vortrags werden die Besonderheiten beim Einsatz von Messtechnik bei Versuchen im Groß- und Realmaßstab und unter Freifeldbedingungen dargestellt. Anhand des Themenfeldprojektes CoFi-ABV und der dort durchgeführten Versuchsreihen werden die Rand- und Rahmenbedingungen beim Durchführen der Experimente, Instrumentierung und Versuchsaufbau sowie beispielhafte Ergebnisse erläutert. T2 - Lehrveranstaltung "Experimentelle Methoden der Aerodynamik" an der TU Berlin CY - Berlin, Germany DA - 24.01.2023 KW - Alternative Antriebe KW - Behälterversagen KW - Fahrzeugbrand KW - Großversuch KW - Auswirkungsbetrachtung PY - 2023 AN - OPUS4-56951 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel A1 - Patzelt, Katrin T1 - Die BAM als Partnerin in der Zivilen Sicherheitsforschung N2 - Was kann die Partnerin in der Zivilen Sicherheitsforschung leisten, welche Möglichkeiten in der Zusammenarbeit mit BOS gibt es? T2 - ForAn - Lunch and Learn CY - Online meeting DA - 14.06.2023 KW - TTS KW - Security KW - BOS KW - Zivile Sicherheitsforschung PY - 2023 AN - OPUS4-57681 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel A1 - Beerhues, Tonja A1 - Grasse, Dennis A1 - Donner, Marcel A1 - Kluge, Martin A1 - Seeber, Henrik T1 - Einsatz von Körpermnodellen bei der Auswirkungsbetrachtung auf das "System Mensch" N2 - In diesem Vortrag werden aktuelle Arbeiten der BAM zu Auswirkungsbetrachtungen bei Stoff- und Energiefreisetzungen mit Zielstellung der Erfassung und Beurteilung der Einwirkungen auf den Menschen vorgestellt. T2 - 3. DUMMY.CRASHTEST.KONFERENZ. CY - Münster, Germany DA - 20.06.2023 KW - Auswirkungsbetrachtung KW - Dummy KW - Körpermodell PY - 2023 AN - OPUS4-57747 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel A1 - Henrik, Seeber A1 - Grobert, S. A1 - Hauer, T. T1 - Das primäre Explosionstrauma - experimenteller Ansatz zur Simulation der intrakorporalen Stoßwellenausbreitung nach Explosionen N2 - Im Rahmen dieses Vortrages wurden aktuelle Arbeiten im Rahmen der Forschungszusammenarbeit mit dem Bundeswehrkrankenhaus Berlin zum primären Explosionstrauma vorgestellt. T2 - BBK-Fachkongress "Forschung für den Bevölkerungsschutz" CY - Bonn, Germany DA - 12.01.2023 KW - Blast KW - Primäres Explosionstrauma KW - Einsatzkräfte KW - Polizei KW - Körpermodell PY - 2023 AN - OPUS4-56894 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krankenhagen, Rainer A1 - Weigel, Sandra T1 - Photothermal investigation of original and degraded asphalt N2 - Asphalt is one of the most common materials used in road construction. It is subject to both chemical and structural aging processes during use. At least to our knowledge, it is not currently known whether these aging processes also lead to a measurable change in the thermal properties of asphalt. If so, these changes could be exploited for non-destructive testing of the aging condition in situ. Photothermal analysis of a component surface involves looking at the time course of the surface temperature during and after pulse-like heating with an expanded laser beam. In the case of concrete surfaces, this method works well under laboratory conditions. It allowed the determination of the thermal effusivity. Now it should be investigated whether the photothermal signal allows conclusions to be made regarding the aging state of the asphalt. Within the scope of this paper, 2 asphalt specimens were investigated: a closed asphalt with 3% void content (SMA 11S) and an open-pore asphalt with 25% void content (PA 8). Both samples were artificially degraded according to a standardized procedure, leaving a portion of the surface unaffected. Subsections from both areas were then separated for photothermal testing. It was found, that the photothermal method is apparently not sensitive enough to detect aging on asphalt in general. However, it is noteworthy that both asphalt types heat up significantly faster than would be expected from the theory of heat conduction, which might be explained by the specific microstructure. T2 - 22nd Conference ECTP "European Confence on thermophysical properties" CY - Venice, Italy DA - 10.09.2023 KW - Asphalt KW - Ageing KW - Photothermal PY - 2023 AN - OPUS4-58857 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kasch, Thomas A1 - Hesse, Olaf T1 - Oxygen service – Tests, Risks and Accidents N2 - Materials and components for oxygen service must be tested and found suitable for their intended use. For a fire or burn out, three requirments have to be present: Fuel, Oxygen and an ignition source. The presentation gives practival examples for all these three requirements and explaines the background and the assessment criteria of tests at BAM. However, risks still exist and can lead to severe accidents. Some accidents, their effects as well as the possible causes are presented to raise awareness of the specific dangers when handling oxygen. T2 - International Teadit Open House CY - Kirchbichl, Austria DA - 07.09.2023 KW - Oxygen KW - Risks KW - Accidents KW - Tests PY - 2023 AN - OPUS4-58452 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jafari, Abbas A1 - Vlachas, K. A1 - Chatzi, E. A1 - Unger, Jörg F. T1 - Bayesian finite element model updating using full-field measurements of displacements N2 - Finite element (FE) models are widely used to capture the mechanical behavior of structures. Uncertainties in the underlying physics and unknown parameters of such models can heavily impact their performance. Thus, to satisfy high precision and reliability requirements, the performance of such models is often validated using experimental data. In such model updating processes, uncertainties in the incoming measurements should be accounted for, as well. In this context, Bayesian methods have been recognized as a powerful tool for addressing different types of uncertainties. Quasi-brittle materials subjected to damage pose a further challenge due to the increased uncertainty and complexity involved in modeling crack propagation effects. In this respect, techniques such as Digital Image Correlation (DIC) can provide full-field displacement measurements that are able to reflect the crack path up to a certain accuracy. In this study, DIC-based full field measurements are incorporated into a finite element model updating approach, to calibrate unknown/uncertain parameters of an ansatz constitutive model. In contrast to the standard FEMU, where measured displacements are compared to the displacements from the FE model response, in the force-version of the standard FEMU, termed FEMU-F [1], displacements are applied as Dirichlet constraints. This enables the evaluation of the internal forces, which are then compared to measured external forces, thus quantifying the fulfillment of the momentum balance equation as a metric for the model discrepancy. In the present work, the FEMU-F approach is further equipped with a Bayesian technique that accounts for uncertainties in the measured displacements, as well. Via this modification, displacements are treated as unknown variables to be subsequently identified, while they are allowed to deviate from the measured values up to a certain measurement accuracy. To be able to identify many unknown variables; including constitutive parameters and the aforementioned displacements, the Variational Bayesian technique proposed in [2] is utilized as an approximative technique. A numerical example of a three-point bending case study is presented first to demonstrate the effectiveness of the proposed approach. The parameters of a gradient-enhanced damage material model [4] are identified using noisy synthetic data, and the effect of measurement noise is studied. The ability of the suggested approach on identifying constitutive parameters is then validated using real experimental data from a three-point bending test from [3]. The full field displacements required as input to the inference setup are extracted through a digital image correlation (DIC) analysis of the provided raw images. T2 - GACM-2023 - 10th GACM Colloquium on Computational Mechanics 2023 CY - Vienna, Austria DA - 10.09.2023 KW - Bayesian model updating KW - Full-field measurements KW - Gradient damage model PY - 2023 AN - OPUS4-58288 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jafari, Abbas A1 - Chatzi, E. A1 - Unger, Jörg F. T1 - Bayesian updating of constitutive laws for Finite Element simulation using full field measurements N2 - Developed finite element (FE) models have been recognized as powerful tools for predicting the mechanical behaviour of engineered systems. As a prerequisite, those models need to be improved with respect to various uncertainties; most notably, concerning underlying physics assumptions and unknown parameters. This is very often accomplished by comparing the performance of a model (e.g. the model response) against available data measured from real experiments. Another challenge emerges in doing that, however, which is accounting for uncertainties of measured data. Bayesian methods have been widely considered and utilized as a suitable approach for coping with and quantifying the aforementioned uncertainties. Phenomena like damage - in particular in quasi-brittle materials - introduce further uncertainties due to the complexity underlying the crack propagation of phenomenon. This implies that, the fitting of a numerical model and an associated constitute law that can adequately describe such effects is non-trivial. The standard approach of finite element model updating (FEMU) is therefore modified to account for tracking of the crack propagation, as recorded during an experiment under increasing loading, via full field displacement measurements. The latter are fed as Dirichlet constraints to an available finite element model, leading to the evaluation of force residuals, which quantifies the accuracy of the model. This approach - which is known as FEMU-F (force-version of the standard FEMU) [1] - is here further equipped with a Bayesian technique, which accounts for the measurement uncertainties in the full field displacement. This is achieved by penalizing the discrepancy between the measured displacements and the modeled Dirichlet constraints, where the latter are considered as further unknowns. We specifically employ the Variational Bayesian technique, proposed in [2], as an approximating tool for the estimation of posterior parameters, including displacement variables that are allowed to deviate from the measurements. A Markov chain Monte Carlo (MCMC) is also used for sampling the posterior distribution of the unknown model parameters. The model updating procedure is first demonstrated through a numerically simulated example of threepoint bending, where the parameters of a gradient-enhanced damage material model [4] are identified in accordance with synthetic noisy data (displacements and reaction forces). For the validation, experimental data from a three-point bending test are used, where full field displacements are collected through a digital image correlation (DIC) analysis (raw data taken from [3]). The data is then used for the parameter identification of a gradient damage constitutive law, which is employed as an ansatz model T2 - 5th International Conference on Uncertainty Quantification inUNCECOMP 2023 - Computational Science and Engineering CY - Athens, Greece DA - 12.06.2023 KW - Bayesian model updating KW - Full field measurements KW - Gradient damage model PY - 2023 AN - OPUS4-58287 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häßler, Dustin A1 - Mund, M. A1 - Daus, Lars-Hendrik A1 - Hothan, Sascha A1 - Schaumann, P. A1 - Schartel, Bernhard T1 - Durability of intumescent coatings N2 - For intumescent coatings durability is an important aspect. Due to ageing, which is caused by climatic conditions, the thermal protection performance of intumescent coatings can be reduced during the working life. The national German and the European procedures to assess the durability of intumescent coatings presume a working life of 10 years. For a longer period, additional investigations are required. However, the European assessment procedure does not provide specific information how to prove a durability of more than 10 years. In addition to this formal reason, also from a scientifical position, it is necessary to investigate the degradation of intumescent coatings in detail to propose a corresponding test concept for a durability of more than 10 years. The presentation summarises the existing knowledge about the degradation behaviour and ageing of intumescent coatings. Furthermore, the results of different approaches from a recently conducted research project are presented. Starting from a water-based and an epoxy-based guide formulation, in a first approach a degradation of the intumescent coating was carried out directly during the production process, i.e. by reducing the concentration of functionally relevant chemical components. In another approach, the duration of the short-term weathering tests was significantly extended, i.e. by multiple repetition of the artificial weathering. The thermal protection performance of the intumescent coating was assessed by fire tests and tests with electrical heating source. In addition, small-scale tests were carried out to determine the thermal material properties of the intumescent coating and thermo-analytical methods were applied to characterise the degradation. Derived from this knowledge, possibilities to test and assess a working life for a period of more than 10 years are proposed. T2 - European Conference - Protective & Fire-Retardant Coatings CY - Berlin, Germany DA - 18.10.2023 KW - Intumescent coating KW - Steel KW - Fire protection KW - Durability PY - 2023 AN - OPUS4-58637 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hofmann-Böllinghaus, Anja T1 - Europäische Harmonisierung von Brandstatistiken für Wohngebäude N2 - Das EU Projekt EU FireStat SI2.830108, das vom Europäischen Parlament finanziert und von der DG GROW der Europäischen Kommission in Auftrag gegeben wurde, hat aufgearbeitet, welche Terminologie in den europäische Mitgliedsstaaten verwendet wird und die von den Mitgliedstaaten erhobenen Daten über Gebäudebrände zu analysieren. Dabei wurden die Schwierigkeiten bei der Erfassung und die Unterschiede bei der Auslegung ermittelt und eine gemeinsame Terminologie sowie eine Methode zur Erfassung der erforderlichen Daten vorgeschlagen. Folgende Schwerpunkte wurden bearbeitet: Zunächst erfolgte eine Diagnose von Terminologie-, Datenerhebungs- und Auslegungsproblemen, Erhebung der Terminologie und der Datenerfassung, Identifizierung der für die Entscheidungsfindung benötigten Daten, Analyse der Methoden zur Datenerhebung Definition einer gemeinsamen Terminologie, Methodik der Kosten-/Nutzenbewertung zur Unterstützung politischer Entscheidungen, Fallstudie zur Anwendung der Methode der Kosten-/Nutzenbewertung, Beschreibung einer zukünftigen Datenerhebungsmethode. Das Ergebnis des Projekts ist eine Empfehlung, welche Daten in den Mitgliedstaaten erhoben werden sollten, um wissensbasierte Entscheidungen in Bezug auf den Brandschutz zu ermöglichen. Damit wird die Grundlage für Maßnahmen und Initiativen geschaffen, die den Brandschutz und die Brandverhütung der Mitgliedstaaten unterstützen, so dass knappe Ressourcen gezielt eingesetzt werden können. T2 - 69. Jahresfachtagung der Vereinigung zur Förderung des Deutschen Brandschutzes CY - Münster, Germany DA - 15.05.2023 KW - Statistik PY - 2023 AN - OPUS4-57574 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hofmann-Böllinghaus, Anja A1 - Klippel, A. T1 - Feuer und Rauchausbreitung in Busdepots, Brandverhalten von Bussen N2 - Präsentation zur Problemen der Brandsicherheit bei Busdepots und Empfehlungen zur Verbesserung der Brandsicherheit. T2 - Brandschutz von Bus-Betriebshöfen CY - Cologne, Germany DA - 02.05.2023 KW - Brandschutz PY - 2023 AN - OPUS4-57416 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hicke, Konstantin T1 - Using DAS for monitoring of infrastructures and for seismic sensing applications N2 - After describing the basics of distributed fiber optic sensing in general and distributed fiber optic acoustic sensing (DAS) in particular, several currently and previously investigated fields of application of DASin infrastructure monitoring and seismic monitoring are presented. A focus is placed on seismic measurements and DAS measurements determining the dynamic responses of concrete structures to certain stimuli. T2 - Meeting of the WAVE Initiative Hamburg CY - Online meeting DA - 09.02.2023 KW - Distributed acoustic sensing KW - DAS KW - Dynamic structural response KW - Seismic measurements KW - Bridge monitoring KW - Traffic monitoring PY - 2023 AN - OPUS4-57007 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hicke, Konstantin A1 - Xu, R. T1 - Akustisches SpRK Monitoring mit SEA und verteilten faseroptischen Sensoren N2 - Von Hand erzeugte Spanndrahtbrüche in einem BTE-Brückenträger wurden mit Schallemissionsanalyse und verteilter faseroptischer akustischer Sensorik detektiert bzw. gemessen. Eigenheiten und Ergebnisse der beiden Methoden werden dargestellt und ihre Performance verglichen. T2 - 12. Symposium "Experimentelle Untersuchungen von Baukonstruktionen" (SEUB) CY - Dresden, Germany DA - 01.06.2023 KW - Verteilte faseroptische akustische Sensorik KW - DAS KW - Brückenmonitoring KW - Spanndrahtbruchdetektion KW - Schallemissionsanalyse KW - SEA PY - 2023 AN - OPUS4-57580 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hicke, Konstantin A1 - Chruscicki, Sebastian A1 - Breithaupt, Mathias A1 - Costard, René A1 - Kind, Thomas A1 - Hüsken, Götz A1 - Agasty, Amit T1 - Measuring Dynamic Behavior and Damage Evolution of a Reinforced Concrete Wall Subjected to Explosive Blasts using Embedded Distributed Fiber Optic Sensors N2 - Results from highly dynamic and static strain measurements, respectively, using embedded distributed fiber optic sensors in a steel-reinforced concrete wall under explosive blast-loading are presented, detailing the structure’s dynamic behavior and the evolutions of cracks. T2 - 28th International Conference on Optical Fiber Sensors (OFS-28) CY - Hamamatsu, Japan DA - 20.11.2023 KW - Distributed acoustic sensing KW - DAS KW - Structural response KW - Blast experiment KW - Embedded fiber optic sensor PY - 2023 AN - OPUS4-59094 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herrmann, Ralf A1 - Simon, Patrick A1 - Schneider, Ronald A1 - Hille, Falk A1 - Baeßler, Matthias T1 - SHM system integration and experiments at a high speed railway bridge N2 - The long-term preservation of our infrastructure requires not only intelligent sensor technology and highly developed monitoring procedures, but also innovative digital tools for analyzing, evaluating and utilizing the results. This includes mathematical and, in particular, probabilistic methods for damage detection and tracking as well as for calculating service life and maintenance cycles and data management. The example project Maintal Bridge Gemuenden as part of the AISTEC project shows the workflow for the implementation of structural health monitoring and experimental tests with a train of Deutsche Bahn. The influence lines, as one possible way for damage detection, were measured with a highly accurate GNSS System to locate the trains position when crossing the bridge. The results were compared to measurements from 1987 just before the bridge went in operation. T2 - Structural Health Monitoring Using Statistical Pattern Recognition CY - Berlin, Germany DA - 20.03.2023 KW - SHM KW - Maintal Bridge Gemuenden KW - Load Test KW - Damage Detection KW - Railway PY - 2023 AN - OPUS4-57242 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Explosionsschutz - Grundlagen und Maßnahmen zum nichtelektrischen Explosionsschutz N2 - Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören. Bei Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen als auch die abgetrennten Partikel können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm DIN EN ISO 80079-36:2016 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. T2 - Ausbildung zum Explosionsschutzbeauftragten, Veranst.-Nr. VA23-00064-050-E, im Haus der Technik e.V. (HdT) CY - Essen, Germany DA - 13.06.2023 KW - Schlagfunken KW - Schleiffunken KW - Reibfunken KW - Mechanisch erzeugte Funken KW - Nichtelektrische Funken KW - Mechanischer Explosionsschutz KW - Nichtelektrischer Explosionsschutz KW - Bestimmungsgemäßer Gebrauch im Explosionsschutz PY - 2023 AN - OPUS4-57680 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Nichtelektrischer Explosionsschutz - Grundlagen und Maßnahmen zum nichtelektr. Explosionsschutz N2 - Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören. Bei Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen als auch die abgetrennten Partikel können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm DIN EN ISO 80079-36:2016 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. T2 - Ausbildung zum Explosionsschutzbeauftragten (Veranst.-Nr. VA23-01191-050-E) im Haus der Technik (HdT) - Außeninstitut der RWTH Aachen und der Universität Duisburg-Essen, 45127 Essen CY - Essen, Germany DA - 24.01.2023 KW - Mechanisch erzeugte Funken KW - Nichtelektrische Funken KW - Schlagfunken KW - Schleiffunken KW - Reibfunken KW - Nichtelektrische Zündquellen KW - Mechanische Zündquellen PY - 2023 AN - OPUS4-56899 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Explosionsschutz - Grundlagen und Maßnahmen zum nichtelektrischen Explosionsschutz N2 - Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen gemäß 2014/34/EU muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören. Bei mechanischen Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke bzw. Bauteile zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen (Zündquelle "heiße Oberflächen") als auch die abgetrennten Partikel (Zündquelle "mechanisch erzeugte Funken") können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm DIN EN ISO 80079-36:2016 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. T2 - Ausbildung zum Explosionsschutzbeauftragten beim Haus der Technik (HdT) CY - Essen, Germany DA - 22.08.2023 KW - Bestimmungsgemäßer Gebrauch im explosionsgefährdeten Bereich KW - Nichtelektrische Funken KW - Mechanische Funken KW - Nichtelektrischer Explosionsschutz KW - Mechanischer Explosionsschutz KW - Reibfunken KW - Schleiffunken KW - Schlagfunken PY - 2023 AN - OPUS4-58110 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Explosionsschutz Grundlagen und Maßnahmen zum nichtelektrischen Explosionsschutz N2 - Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen gemäß 2014/34/EU muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören. Bei mechanischen Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke bzw. Bauteile zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen (Zündquelle "heiße Oberflächen") als auch die abgetrennten Partikel (Zündquelle "mechanisch erzeugte Funken") können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm DIN EN ISO 80079-36:2016 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. T2 - Ausbildung zum Explosionsschutzbeauftragten, Veranst.-Nr. VA23-00065-050-E CY - Essen, Germany DA - 05.12.2023 KW - Mechanisch erzeugte Funken KW - Nichtelektrische Funken KW - Nichtelektrischer Explosionsschutz KW - Mechanischer Explosionsschutz KW - Schlagfunken KW - Schleiffunken KW - Reibfunken PY - 2023 AN - OPUS4-59066 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunert, Wiebke T1 - EU project ODYSSEUS N2 - Fortschrittsbericht über das EU-Projekt ODYSSEUS (BAM VH 2550). T2 - International technical exchange at BKA CY - Wiesbaden, Germany DA - 08.11.2023 KW - Homemade explosives KW - HME KW - Precurser PY - 2023 AN - OPUS4-58801 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunert, Wiebke T1 - EU Projekt ODYSSEUS – Year 2 Update N2 - Es werden das EU-finanzierte FE-Projekt ODYSSEUS, ausgewählte Ergebnisse zum Thema Home-made-explsosives (HMEs) und precursers, aktuelle Fragestellungen und ein Ausblick vorgestellt. T2 - 23. Internationales Symposium des Bundeskriminalamtes für Sprengstoffermittelnde und Entschärfende unkonventioneller Spreng- und Brandvorrichtungen CY - Magdeburg, Germany DA - 27.11.2023 KW - Home-made-explosives (HME) KW - Precurser PY - 2023 AN - OPUS4-58975 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunert, Wiebke T1 - EU project ODYSSEUS - Improving Knowledge on HMEs N2 - The ODYSSEUS project aims at improving knowledge about explosives precursers/HMEs and at developing and improving prognostic and detection tool to counter and prevent terrorist attacks. The contribution presents an overview of the ODYSSEUS approaches in countering and preventing terrorist attacks. The lecture will also show what knowledge has been gained to date about HMEs and new precursers and what consequences result from this. T2 - EXERTER Final Conference CY - Soest, Netherlands DA - 24.04.2023 KW - HME KW - Preparation of HME KW - Misuse of explosives KW - EU project ODYSSEUS PY - 2023 AN - OPUS4-57387 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grobert, Steffen A1 - Krentel, Daniel A1 - Grasse, Dennis A1 - Seeber, Henrik A1 - Donner, Marcel A1 - Hauer, Thorsten T1 - Primäres Explosionstrauma im militärischen Kontext - Herausforderungen für den Arbeitsschutz N2 - Im Rahmen dieses Vortrags wurden aktuelle Arbeiten der BAM im Rahmen der Forschungszusammenarbeit mit dem Bundeswehrkrankenhaus Berlin zum primären Explosionstrauma vorgestellt. Den Schwerpunkt des Vortrags bildeten die Auswirkungen der kumulierten Belastung durch "low-level blast" auf das Gehirn von Einsatzkräften und Rückschlüsse für den Arbeitsschutz und die Arbeitsmedizin. T2 - Fortbildung der Aufsichtspersonen der öffentlich-rechtlichen Aufsichten der Bundeswehr CY - Mannheim, Germany DA - 04.12.2023 KW - Blast KW - Primäres Explosionstrauma KW - Einsatzkräfte KW - mTBI KW - Arbeitsschutz PY - 2023 AN - OPUS4-59181 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Goller, Sebastian M. A1 - Krüger, Simone A1 - Schartel, Bernhard T1 - Avoiding antimony – effect of Ca(H2PO2)2 on smoke emission and fire behaviour in brominated ABS N2 - The replacement of antimony trioxide (Sb2O3) in brominated flame-retardant ABS (ABS/FR) is of great interest. This study investigates the influence of calcium hypophosphite (CaP) in ABS/FR on flame retardancy and smoke emission. Different amounts of talc are added to ABS/FR/CaP to evaluate the influence of an inorganic barrier on smoke emission and flame retardancy. The cone calorimeter unveiled a reduction by 46% in PHRR for ABS/FR/CaP. Additional 8 wt.-% talc (ABS/FR/CaP/8Talc) reduced the PHRR by 61%. ABS/FR/CaP exhibited a more condensed phase action, which resulted in less smoke emission. The study investigates the influence of CaP in ABS/FR on the smoke toxicity, smoke density and the smoke particles distribution in the smoke density chamber (ISO 5659-2) coupled to a FTIR spectrometer and electrical low pressure cascade impactor (ELPI). T2 - 5th Asia-Oceania Symposium on Fire Safety Materials Science and Engineering CY - Sydney, Australia DA - 26.08.2023 KW - Smoke KW - ABS KW - Calcium hypophosphite KW - Antimony KW - Brominated flame retardant KW - Fire scenario KW - Burning behavior PY - 2023 AN - OPUS4-58232 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Nikoonasab, Ali A1 - Licht, M. A1 - Müller, Thoralf A1 - Achenbach, R. A1 - Raupach, M. T1 - Reinforcing steel in sulfide-containing concretes – corroding or not corroding? N2 - Blast furnace cements (CEM III) and alkali-activated slags are binders for concretes with several advantageous engineering properties, and their increased adoption in construction industry could contribute to reducing the CO2 emissions associated with cement production and use. However, the current knowledge about how these cements protect steel reinforcement in concretes against corrosion is very incomplete, which impedes their large-scale application. This knowledge gap is mainly due to the fact that these cements release sulfide and other reduced sulfur species into the concrete pore solution, the consequences of which for the state of the reinforcement and electrochemical measurements are not fully understood. The present contribution first describes peculiarities of electrochemical measurements of steel in sulfide-containing cementitious materials and related solutions as reported in the literature and a recent report by EFC Working Party 11. It is demonstrated that the high sulfide concentrations in these systems lead to low open circuit potentials and low polarisation resistances, which may be incorrectly interpreted as indicating active corrosion of the steel. Second, preliminary results of an ongoing project [funded by the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) – 458297195] related to the passivation and corrosion initiation of steel in sulfide-containing solutions and mortars are presented. Eight mortars based on one alkali-activated blast furnace slag (BFS), three alkali-activated BFS/fly ash blends, one sodium sulfate-activated CEM III/C (‘hybrid cement’), one CEM III/C, one CEM III/B, and one CEM I (ordinary Portland cement, OPC) were produced, and their pore solutions expressed and analysed after 7, 14, 28, and 56 days of curing. The pH values of the solutions differed systematically, with the highest pH values recorded for the CEM I and the alkali-activated BFS/fly ash blends with a high proportion of fly ash, and the lowest pH recorded for the CEM III/B. The redox potentials of the solutions were between −500 mV and −340 mV vs. Ag/AgCl for the alkali-activated binders, approx. +10 mV vs. Ag/AgCl for the CEM I, and in between for the CEM III/B and the CEM III/C. As expected, the electrical conductivity was highest for the alkali-activated binders. These results are explained by the chemical compositions of the pore solutions of the mortars. Finally, a test set-up to investigate the behaviour of steel in sulfide-containing solutions and the changes on subsequent oxygen and/or chloride addition is introduced. Preliminary electrochemical measurements of steel in sulfide-containing solutions are presented and discussed in the context of the above-mentioned data from the literature and the compositions of the pore solutions of the studied mortars. T2 - 7th Swiss Corrosion Science Day 2023 CY - Zurich, Switzerland DA - 24.04.2023 KW - Reinforcing steel KW - Sulfide KW - Concrete KW - Ground granulated blast furnace slag KW - Corrosion PY - 2023 AN - OPUS4-57386 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin A1 - Quercetti, Thomas A1 - Gleim, Tobias A1 - Nehrig, Marko A1 - Musolff, André A1 - Wille, Frank T1 - R&D Activities by BAM Related to Transport Package Fire Testing N2 - Packages for the transport of radioactive material shall meet the mechanical and thermal test requirements of the International Atomic Energy Agency (IAEA) regulations for package design approval. Besides mechanical testing, the Federal Institute for Materials Research and Testing (BAM) performs thermal tests in accordance with the IAEA regulations. The thermal test includes a 30-minute 800°C fully engulfing fire. BAM continuously performs various thermal experiments for the investigation of the thermal response of packages with respect to the IAEA fire. The purpose of this paper is to give an overview of the already performed, ongoing and future physical tests and experiments of BAM in the field of thermal investigations. These research and development works shall support our competencies for the authority package design assessment. BAM operates a propane gas fire test facility. To be able to carry out comparative investigations and validity between the propane fire and the in detail prescribed pool fire test in the regulations, BAM carries out various calorimetric tests and investigates the boundary conditions of the fire with the help of fire reference packages. At the same time, we are conducting various fire scenarios with wood-filled impact limiters. Large-scale fire tests of impact limiters are carried out on a full scale as well as on a small scale. Influencing variables are investigated in particular by means of geometric changes and the consideration of artificial damages, in particular holes. In addition to propane fire as a heat source, thermal scenarios are also investigated with hydrogen as heat source and an infrared radiator system to ignite test specimens. For these numerous test arrangements, the transferability to existing and newly developed transport package designs is essential and fruitful within the review of design approvals, especially for Dual Purpose casks with a long-lasting operation time. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 22) CY - Juan-les-Pins, France DA - 11.06.2023 KW - Fire Testing KW - Wood KW - Hydrogen KW - Fire Reference Test PY - 2023 AN - OPUS4-57722 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erxleben, Kjell A1 - Rhode, Michael A1 - Kaiser, Sebastian A1 - Kannengießer, Thomas T1 - Repair welding of in service hydrogen pipelines N2 - In the course of tomorrow's hydrogen-based energy transition, the construction of the corresponding infrastructure will play a central role. In that context, large diameter long-distance transmission pipelines for hydrogen will be the backbone in the European Union with service pressures from 70 to 90 bar (e.g., depending on national regulations). It is a major goal to rededicate the existing LNG infrastructure despite the necessity of new pipelines. From that point of view repairing of such transmissions pipelines via welding can be necessary. For the LNG infrastructure, it is state of the art that repair welding is conducted at pipelines under service, i.e., the LNG is still flowing as pressurized gas in the steel pipes. The reason is that a shut-down of large diameter pipelines is not so easy or sometimes impossible. In fact, as long no oxygen enters the pipeline, there would be any combustion or (in the worst case) explosion. At the moment, it is entirely open if current repair welding procedures for LNG pipelines can be transferred to pure hydrogen pipelines. In opposite to LNG, hydrogen can be way easier absorbed to the pipeline steels and diffuses through the material. If it accumulates in susceptible regions, i.e., in the welded joint, hydrogen assisted embrittlement could occur. The planned welding procedure requires a so-called preheating and maintenance of the weld joint of up to 300°C for several hours. This temperature is way higher compared to the typical service temperature of max. 40 to 50°C at operational pressures of 100 bar. In accordance to API 941, these low-alloyed pipeline steels are subjected to short-term service loads, which they are not designed for. For that reason, a collaborative project between BAM and DVGW (German Association for Gas and Water professions) was initiated in 2022 to answer the following questions by experiments and numerical simulation of: (1) How many hydrogen is additionally absorbed during the heating of the material to max. 300°C under remaining operational pressures? (2) Is the hydrogen concentration sufficient to reach a critical condition? (3) Which material and weld microstructure is the most susceptible? (4) Is there a significant difference in the repair welding behavior of LNG pipelines that had been already in use for long-term? (5) Which welding parameters and joint dimensions must be ensured for safe repair welding repair of typical pipelines? For that reason, the present study gives an overview on the current practice in repair welding of in-service pipelines, the industrial importance of this topic for the hydrogen-based energy transition and summarizes first results. T2 - Eurocorr 2023 - The European Corrosion Congress CY - Brussels, Belgium DA - 27.08.2023 KW - Hydrogen KW - Repair Welding KW - Pipeline KW - In-service KW - High-pressure PY - 2023 AN - OPUS4-58334 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - "Grabenkorrosion": From A historic scientific debate to the solution, still modern failures N2 - Grooving corrosion occured in the 1970ies. It returned in the 1990ies, causing a scientific debate leading to a solution. This solution got lost, so new failures appear. The route of the discussion to the solution is described, old and new failures are discussed. T2 - Eurocorr 2023 CY - Brussels, Belgium DA - 27.08.2023 KW - Grooving corrosion KW - Drinking water installations KW - Steel pipes PY - 2023 AN - OPUS4-58186 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epple, Niklas A1 - Sanchez Trujillo, Camila Andrea A1 - Niederleitinger, Ernst T1 - Ultrasonic monitoring of large-scale structures – input to engineering assessment N2 - Ultrasonic coda wave interferometry can detect small changes in scattering materials like concrete. We embedded ultrasonic transducers in the Gänstorbrücke Ulm, a monitored road bridge in Germany, to test the methodology. Since fall 2020, we've been monitoring parts of the bridge and comparing the results to commercial monitoring systems. We calculate signal and volumetric velocity changes using coda waves, and long-term measurements show that the influence of temperature on strains and ultrasound velocity changes can be monitored. Velocity change maps indicate that different parts of the bridge react differently to environmental temperature changes, revealing local material property differences. A load experiment with trucks allows calibration to improve detectability of possibly damaging events. Our work focuses on measurement reliability, potential use of and distinction from temperature effects, combination with complementary sensing systems, and converting measured values to information for damage and life cycle assessment. T2 - IALCCE 2023 CY - Milano, Italy DA - 02.07.2023 KW - Ultrasonic KW - Monitoring KW - Bridges KW - NDT KW - Coda PY - 2023 AN - OPUS4-58046 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epple, Niklas T1 - Coda Measurements for monitoring infrastructure durability N2 - Presentation about the advancements in the DFG Research unit CoDA, with focus on Coda Wave Monitoring of Infrastructure. With some case studies, possibilities and challenges are discussed on the way towards infrastructural monitoring with CWI. T2 - PhD-Seminar Department 8.2 CY - Berlin, Germany DA - 07.09.2023 KW - CWI KW - Embedded Sensors KW - Ultrasound KW - Bridge Monitoring PY - 2023 AN - OPUS4-58196 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert A1 - Hajhariri, Aliasghar A1 - Camplese, D. A1 - Scarponi, G. E. A1 - Cozzani, V. A1 - Otremba, Frank T1 - Insulation Materials Used in Tanks for the Storage of Cryogenic Fluids in Fire Scenarios N2 - The importance of tanks for storing cryogenic fluids in the energy industry is increasing because of ongoing political conflicts and the implementation of more environmentally friendly energy sources. Key representatives for the application of cryogenic tanks are natural gas in the form of Liquefied Natural Gas (LNG) and hydrogen, e. g. in the form of Liquefied Hydrogen (LH2), for which significantly higher transport capacities can be achieved with the same transport volume using cryogenic storages than with storages based solely on overpressure. What applies to all cryogenic transported fluids in common is their condition that must be maintained. Hence heat flows into the preserved fluid must be minimized. Thermal super Insulations (TSI) based on e. g. multilayer insulations (MLI), perlites, and vacuum are utilized for this purpose and have already proven themselves in similar applications. However, for the use of tanks for cryogenic fluids in the transport sector, there is insufficient knowledge regarding the course and consequences of incidents, which is due to the still short period of use and the few documented incidents, hence few investigations carried out in this field. Typical scenarios in the transport sector represent car accidents with collisions, fires, and their combination, which are associated with extraordinary loads on the tank. The focus of this study is to investigate the behavior of TSI as a result of their thermal exposure to a heat source representing a fire. It is worth mentioning that this could lead to an increase of the heat flux into a tank by several orders of magnitude, and to permanent damage of the TSI, ultimately rapid release of flammable gas as well as a Boiling Liquide Expanding Vapour Explosion (BLEVE). For this purpose, a high temperature thermal vacuum chamber (HTTVC) has been developed that allows thermal loading of MLI or perlites in a vacuum and simultaneous measurement of heat flow through this TSI. The HTTVC is designed to represent realistic insulation conditions and to withstand thermal loads from typical design fires. The HTTVC was applied to investigate TSI based on MLI and vacuum. It is shown that the thermal stress caused permanent damage to the TSI, with shrinkage, phase change, pyrolysis, and condensation being significant damage mechanisms. The results are relevant for the evaluation of accident scenarios and can thus contribute to the improvement of TSI and the development of emergency measures for the protection of persons and infrastructures. T2 - ASME 2023 Pressure Vessels & Piping Conference (PVP2023) CY - Atlanta, Georgia, USA DA - 16.07.2023 KW - LH2 KW - LNG KW - Fire KW - MLI KW - Safety PY - 2023 AN - OPUS4-57974 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Systems for the storage of cryogenic liquefied gases N2 - Liquefied Hydrogen (LH2) or Liquefied Natural Gas (LNG) establish themselves as important energy carriers in the transport sector. Its storage requires tanks with Thermal Super Insulations (TSI) to keep the transported fluid cold. The presentation includes 2 main topics of the department. First TSI has proven itself in various applications over a long time, but not in the land transport sector, where accidents involving collisions, fires, and their combination are to be expected. To analyze fire scenarios a High-Temperature Thermal Vacuum Chamber (HTTVC) was developed that allows the thermal loading of thermal insulation material in a vacuum and measuring the heat flow through the TSI in parallel. Within this chamber, 5 samples were tested regarding 3 different types of MLI, rock wool, and perlites. In the presentation, the results are presented. Second, the studying of accident scenarios enables the improvement of thermal superinsulation and to find novel insulation concepts. This is necessary for LH2 large-scale storages, for which state-of-the-art solutions are not suitable. Within the presentation, a novel insulation concept will be presented. T2 - Specialist Meeting - Threats to HAZMAT Pressure Vessels and BLEVE CY - Berlin, Germany DA - 25.04.2023 KW - Crygenic KW - LH2 KW - LNG KW - Fire KW - MLI PY - 2023 AN - OPUS4-57414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino A1 - Seifert, Lando A1 - Müller, Thoralf T1 - Stress corrosion test in thiocyanate solution with galvanostatic current N2 - Prüfung von Spannstählen hinsichtlich ihrer Anfälligkeit gegenüber wasserstoffinduzierter Spannungsrisskorrosion in kürzeren Zeiträumen. Gewährleistung der Dauerhaftigkeit mittels neuartiger elektrochemischer Prüfverfahren und galvanostatischer Kontrolle und Wasserstoffbeladung T2 - Meeting ISO TC17 SC16 WG8 CY - Online meeting DA - 11.01.2023 KW - Hydrogen KW - Corrosion PY - 2023 AN - OPUS4-56854 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino A1 - Lehmann, Jens T1 - Erörterung des Messprotokolls N2 - Durch das alkalische Milieu des Porenwassers im Beton ist der Stahl normalerweise dauerhaft vor Korrosion geschützt. Unter ungünstigen Umgebungsbedingungen (Chlorideintrag, Carbonatisierung) kann die passive Deckschicht auf der Stahloberfläche zerstört werden. Der Korrosionsprozess ist initiiert. Die entstehenden Korrosionsprodukte werden zunächst vom Porengefüge des Betons aufgenommen, ohne dass es zu sichtbaren Schäden am Bauwerk führt. Im fortgeschrittenem Stadium der Korrosion können sich dann Risse und Abplatzungen bilden. Um notwendige Sanierungsmaßnahmen sowohl aus sicherheitstechnischen Gründen als auch aus wirtschaftlichen Erwägungen rechtzeitig einzuleiten, sind frühzeitige und weitestgehend zerstörungsfreie Prüfverfahren zur Ermittlung der aktuellen Korrosionswahrscheinlichkeit der Stahlbewehrung von großer Bedeutung. Deshalb finden Methoden und Verfahren zur laufenden bzw. regelmäßigen Korrosionsüberwachung von Stahlbetonbauwerken ständig größere Beachtung, sowohl im Bereich Forschung und Entwicklung als auch in der Praxis. Die elektrochemische Potentialfeldmessung ist ein etabliertes und weit verbreitetes Verfahren zur Beurteilung des Korrosionszustandes der Bewehrung in Stahlbetonbauwerken. Mit Hilfe dieses Verfahrens können Bereiche korrodierender Bewehrung zerstörungsfrei lokalisiert werden. In der Regel kommt diese Methode bei der Detektion von chloridinduzierter Korrosion zum Einsatz. Der Lehrgang vermittelt den Teilnehmenden in kompakter Form einen zusammenfassenden Überblick über die notwendigen Grundlagen zum Verständnis der Messmethode, der Vorbereitung und Durchführung der Messungen, der notwendigen Begleituntersuchungen sowie der Interpretation der gewonnenen Daten. Der erste Tag ist der theoretischen Ausbildung gewidmet, am zweiten Tag folgt dann die praktische Anwendung der Lerninhalte. Am dritten Tag folgt die Abnahme der praktischen und theoretischen Prüfung zur Erlangung des Sachkundenachweises. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen CY - Berlin, Germany DA - 24.04.2023 KW - Potentialfeldmessung KW - Korrosion PY - 2023 AN - OPUS4-57496 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino A1 - Burkert, Andreas T1 - Prestressed concrete structures with concentrated tendons - Structural damage due to hydrogen-induced stress corrosion cracking N2 - Hydrogen-induced stress corrosion cracking (HSCC) is well known, and highly sensitive pre-stressing steels are normally not available on the market. But in the case of existing structures, it could be necessary to ensure their safety through special kinds of investigations. Those kinds of investigations are often not applicable in a non-destructive way. Therefore, a once in a lifetime project was initiated. In the course of the deconstruction of the "Bridge of the 20th anniversary of the GDR" at the Altstädter Bahnhof in Brandenburg a. d. Havel, new information on the initiation of hydrogen-induced stress cracks could obtained. The initial observation to do several investigations at this bridge are several meters long longitudinal cracks in the concrete web of the box girder above and below the tension duct. The BAM was commissioned by the Brandenburg State Road Administration to participate in a corresponding joint project which is financed by the Federal Ministry for Digital and Transport. The added value of the new information gained in this project goes beyond the specific structure. It describes unexpected new damage patterns that can be transferred to other structures with concentrated tendons (tendon block method and Baur-Leonhardt method) and were previously unknown in this form. These should be made known to other developers to enable them to initiate any necessary actions. One of the major results is, the wire breaks observed at this bridge can be attributed to cracking as a result of HSCC and subsequent crack growth until breakage, due to cyclic loading from traffic and alternating restraint stresses. The probable trigger here was crevice corrosion processes at the contact points of the wires to the spacer plates in superposition with high tensile stresses due to prestressing after or with in grouting the duct. Tension wire breaks, which may have occurred before grouting and during prestressing, were not detected. The unfavorable gap situation at the spacer plates occurs over the entire cross-section of the prestressing channel and can thus affect each individual prestressing wire. Losses in the load-bearing capacity of the prestressed concrete structure can then be the result. A disadvantage of the prestressing block method in this respect is that a large number of individual wires can be affected at the same time (theoretically all wires), which can reduce the prestressing effect of the concentrated tendon accordingly. With the usual use of only one tendon per web, the possibility of load transfer to other tendons is thus not given (lack of redundancy). T2 - 4rd International Congress on Materials & Structural Stability CY - Rabat, Morocco DA - 08.03.2023 KW - Corrosion KW - HSCC KW - Wasserstoff KW - Spannungsrisskorrosion PY - 2023 AN - OPUS4-57158 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino A1 - Burkert, Andreas T1 - Standortabhängige Dauerhaftigkeitsbetrachtungen von Zink unter atmosphärischer Korrosion N2 - In maritimer Exposition können Zinkbauteile Nutzungsdauern von 50 Jahren erreichen. Dabei werden Expositionen mit Spritzwasserbelastung durch Meerwasser nicht betrachtet. Normative Betrachtungen und Korrosionsprognosen basierend auf Einjahreswerten liefern hier grundlegend falsche Ergbnisse, da sie eine signifikant höhere Belastung der Atmosphäre mit SO2 voraussetzen. T2 - GAV-Forschungsbeiratssitzung CY - Darmstadt, Germany DA - 17.05.2022 KW - Korrosion KW - Zink PY - 2023 AN - OPUS4-57631 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino A1 - Burkert, Andreas A1 - Babutzka, M. T1 - Standortabhängige Dauerhaftigkeitsbetrachtungen von Zink unter atmosphärischer Korrosion N2 - In maritimer Exposition können Zinkbauteile Nutzungsdauern von 50 Jahren erreichen. Dabei werden Expositionen mit Spritzwasserbelastung durch Meerwasser nicht betrachtet. Normative Betrachtungen und Korrosionsprognosen basierend auf Einjahreswerten liefern hier grundlegend falsche Ergbnisse, da sie eine signifikant höhere Belastung der Atmosphäre mit SO2 voraussetzen. T2 - Korrosionsschutz in der maritimen Technik CY - Hamburg, Germany DA - 04.05.2023 KW - Korrosion KW - Feuerverzinkter Stahl PY - 2023 AN - OPUS4-57489 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino A1 - Burkert, Andreas A1 - Babutzka, M. T1 - Standortabhängige "Dauerhaftigkeitsprognose mittels Langzeitauslagerungsversuchen" von Zink N2 - In maritimer Exposition können Zinkbauteile Nutzungsdauern von 50 Jahren erreichen. Dabei werden Expositionen mit Spritzwasserbelastung durch Meerwasser nicht betrachtet. Normative Betrachtungen und Korrosionsprognosen basierend auf Einjahreswerten liefern hier grundlegend falsche Ergebnisse, da sie eine signifikant höhere Belastung der Atmosphäre mit SO2 voraussetzen. T2 - Künstliche Intelligenz vs. Maritime Korrosion - Where do we go? CY - Hamburg, Germany DA - 11.07.2023 KW - Korrosion KW - Korrosivität PY - 2023 AN - OPUS4-57911 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Befestigungsmittel im Bauwesen - Der richtige Werkstoff!? N2 - Die Anforderungen in verschiedenen Fachgebieten des Bauwesens an metallene Befestigungsmittels hinsichtlich des Korrosionsschutzes sind zum einen Abhängig von den verwendeten Werkstoffen und zum anderen von der Korrosivität in der jeweiligen Exposition. Hier wird ein Überblick über die gängigen Werkstoffe als auch Anwendung und Fehlerquellen verschafft T2 - Vorlesung TU-Berlin CY - Berlin, Germany DA - 05.07.2023 KW - Korrosion KW - Korrosionsschutz PY - 2023 AN - OPUS4-57882 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Potentialfeldmessung in Theorie und Praxis N2 - Durch das alkalische Porenwassermilieu ist Stahl im Beton vor Korrosion geschützt. Unter ungünstigen Umgebungsbedingungen (Karbonatisierung, Chlorideintrag) kann die passive Deckschicht auf der Stahloberfläche zerstört werden. Im weiteren Verlauf können sich korrosionsbedingte Folgeschäden, wie Risse und Abplatzungen am Bauwerk ergeben. Um notwendige Sanierungsmaßnahmen sind frühzeitige und weitgehend zerstörungsfrei ermittelte Informationen über das aktuelle Korrosionsverhalten der Stahlbewehrung von großer Bedeutung. Die Potentialfeldmessung ist ein etabliertes und weit verbreitetes Verfahren zur Beurteilung des Korrosionszustandes der Bewehrung in Stahlbetonbauwerken. Mit Hilfe dieses Verfahrens können Bereiche aktiv korrodierender Bewehrung zerstörungsfrei lokalisiert werden. In der Regel kommt diese Messmethode bei der Detektion chloridinduzierter Korrosion zum Einsatz T2 - TU-Vorlesung CY - Berlin, Germany DA - 28.06.2023 KW - Korrosion KW - Potentialfeldmessung PY - 2023 AN - OPUS4-57883 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Potential mapping at concrete structures N2 - Potentialmapping is an electrochemical measurement for the detection of active corroding reinforcement at concrete structures. T2 - NDT&E Workshop 2023 CY - Berlin, Germany DA - 23.06.2023 KW - Corrosion KW - Potentialfeldmessung PY - 2023 AN - OPUS4-57884 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Brückenbauwerke aus Spannbeton - der Weg von der initiierung Wasserstoffinduzierter Spannungsrisskorrosion bis zum Bauwerksversagen N2 - Bei der Brücke Altstädter Bahnhof handelte es sich um eine große Spannbetonkonstruktion, die einen elementaren Ver­kehrsknotenpunkt in der Stadt Brandenburg an der Havel bil­dete. Entgegen üblichen Spannbetonkonstruktionen mit kleinen Bündelspanngliedern kamen beim Haupttragwerk in Längsrich­tung großformatige Spannblockspannglieder zum Einsatz. Im Fall der vorliegenden Brücke setzte sich das Spannglied aus 392 ovalen Einzeldrähten aus Hennigsdorfer Produktion zusam­men, welche als spannungsrisskorrosionsgefährdet gelten. Bei Bauwerkserkundungen wurde ein hoher Versprödungsgrad der Spannstähle festgestellt, sodass die Brücke am 19.05.2021 ge­sprengt werden musste. Zuvor traten im Bereich detektierter Spanndrahtbrüche von außen erkennbare Längsrisse in den Stegen anstatt von üblicherweise quer gerichteten Biegerissen an der gezogenen Randfaser auf. Die abweichende Schadens­äußerung im Falle einer Spannstahlschädigung brachte das Bundesministerium für Digitales und Verkehr (BMDV) dazu, weitergehende Untersuchungen durchzuführen. In Zusammen­arbeit mit dem Landesbetrieb Straßenwesen Brandenburg, der Hochschule für Technik und Wirtschaft Dresden sowie der Bundesanstalt für Materialforschung und ­prüfung (BAM) wur­den experimentelle Untersuchungen in­situ konzipiert und durchgeführt. Im Konkreten wurde an zwei Messstellen eine gezielte Schädigung des großformatigen Spannglieds vorge­nommen, um das zuvor vorgefundene Schadensbild nach­zuvoll ziehen und validieren zu können. Konzept, Ergebnisse aus den Untersuchungen und Erkenntnisse für gleichartig ausge­führte Bauwerke sind Gegenstand des ersten Beitrags (Teil 1). Der zweite Teil [1] wird sich im Schwerpunkt den verwendeten Messverfahren und Monitoringsystemen widmen, welche die Durchführung des Versuchs begleiteten. T2 - FKKS-Jahrestagung CY - Berlin, Germany DA - 06.07.2023 KW - Korrosion KW - Spannungsrisskorrosion KW - Spannstahl KW - Wasserstoff PY - 2023 AN - OPUS4-57885 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Galvanic Anode systems in Concrete structures and their performance part 1 N2 - Corrosion of reinforcement is one of the major reasons in questioning the sturdiness of building structures. The application of cathodic protection techniques plays a big role in controlling the corrosion process to ensure a longer service life of building structures. This systematic study compares the efficiency and durability of various discrete galvanic zinc anode systems available in the current market using different criteria for measuring efficiencies such as potential measurements, electrolyte resistance measurements and several polarization methods to determine the polarizability of the anodes. Results to validate the performance of long-time exposure of discrete zinc anodes in the concrete medium are already shown in 2021. Now the results of analyzing the phase boundary between mortar and anodes by using 3D computer tomography are shown, as also the field application at large-scale specimens where the potential distribution and the current were investigated. T2 - Eurocorr 2023 CY - Brussels, Belgium DA - 27.08.2023 KW - Corrosion KW - Corrosion Protection PY - 2023 AN - OPUS4-58169 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Elektrochemische Messungen N2 - Durch das alkalische Milieu des Porenwassers im Beton ist der Stahl normalerweise dauerhaft vor Korrosion geschützt. Unter ungünstigen Umgebungsbedingungen (Chlorideintrag, Carbonatisierung) kann die passive Deckschicht auf der Stahloberfläche zerstört werden. Der Korrosionsprozess ist initiiert. Die entstehenden Korrosionsprodukte werden zunächst vom Porengefüge des Betons aufgenommen, ohne dass es zu sichtbaren Schäden am Bauwerk führt. Im fortgeschrittenem Stadium der Korrosion können sich dann Risse und Abplatzungen bilden. Um notwendige Sanierungsmaßnahmen sowohl aus sicherheitstechnischen Gründen als auch aus wirtschaftlichen Erwägungen rechtzeitig einzuleiten, sind frühzeitige und weitestgehend zerstörungsfreie Prüfverfahren zur Ermittlung der aktuellen Korrosionswahrscheinlichkeit der Stahlbewehrung von großer Bedeutung. Deshalb finden Methoden und Verfahren zur laufenden bzw. regelmäßigen Korrosionsüberwachung von Stahlbetonbauwerken ständig größere Beachtung, sowohl im Bereich Forschung und Entwicklung als auch in der Praxis. Die elektrochemische Potentialfeldmessung ist ein etabliertes und weit verbreitetes Verfahren zur Beurteilung des Korrosionszustandes der Bewehrung in Stahlbetonbauwerken. Mit Hilfe dieses Verfahrens können Bereiche korrodierender Bewehrung zerstörungsfrei lokalisiert werden. In der Regel kommt diese Methode bei der Detektion von chloridinduzierter Korrosion zum Einsatz. Der Lehrgang vermittelt den Teilnehmenden in kompakter Form einen zusammenfassenden Überblick über die notwendigen Grundlagen zum Verständnis der Messmethode, der Vorbereitung und Durchführung der Messungen, der notwendigen Begleituntersuchungen sowie der Interpretation der gewonnenen Daten. Der erste Tag ist der theoretischen Ausbildung gewidmet, am zweiten Tag folgt dann die praktische Anwendung der Lerninhalte. Am dritten Tag folgt die Abnahme der praktischen und theoretischen Prüfung zur Erlangung des Sachkundenachweises. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen CY - Berlin, Germany DA - 24.04.2023 KW - Potentialfeldmessung KW - Korrosion PY - 2023 AN - OPUS4-57494 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Merkblatt B 03 der DGZfP - Ausgabe April 2021 N2 - Durch das alkalische Milieu des Porenwassers im Beton ist der Stahl normalerweise dauerhaft vor Korrosion geschützt. Unter ungünstigen Umgebungsbedingungen (Chlorideintrag, Carbonatisierung) kann die passive Deckschicht auf der Stahloberfläche zerstört werden. Der Korrosionsprozess ist initiiert. Die entstehenden Korrosionsprodukte werden zunächst vom Porengefüge des Betons aufgenommen, ohne dass es zu sichtbaren Schäden am Bauwerk führt. Im fortgeschrittenem Stadium der Korrosion können sich dann Risse und Abplatzungen bilden. Um notwendige Sanierungsmaßnahmen sowohl aus sicherheitstechnischen Gründen als auch aus wirtschaftlichen Erwägungen rechtzeitig einzuleiten, sind frühzeitige und weitestgehend zerstörungsfreie Prüfverfahren zur Ermittlung der aktuellen Korrosionswahrscheinlichkeit der Stahlbewehrung von großer Bedeutung. Deshalb finden Methoden und Verfahren zur laufenden bzw. regelmäßigen Korrosionsüberwachung von Stahlbetonbauwerken ständig größere Beachtung, sowohl im Bereich Forschung und Entwicklung als auch in der Praxis. Die elektrochemische Potentialfeldmessung ist ein etabliertes und weit verbreitetes Verfahren zur Beurteilung des Korrosionszustandes der Bewehrung in Stahlbetonbauwerken. Mit Hilfe dieses Verfahrens können Bereiche korrodierender Bewehrung zerstörungsfrei lokalisiert werden. In der Regel kommt diese Methode bei der Detektion von chloridinduzierter Korrosion zum Einsatz. Der Lehrgang vermittelt den Teilnehmenden in kompakter Form einen zusammenfassenden Überblick über die notwendigen Grundlagen zum Verständnis der Messmethode, der Vorbereitung und Durchführung der Messungen, der notwendigen Begleituntersuchungen sowie der Interpretation der gewonnenen Daten. Der erste Tag ist der theoretischen Ausbildung gewidmet, am zweiten Tag folgt dann die praktische Anwendung der Lerninhalte. Am dritten Tag folgt die Abnahme der praktischen und theoretischen Prüfung zur Erlangung des Sachkundenachweises. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen CY - Berlin, Germany DA - 24.04.2023 KW - Potentialfeldmessung KW - Korrosion PY - 2023 AN - OPUS4-57495 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Mögliche Fehlerquellen in der Praxis N2 - Durch das alkalische Milieu des Porenwassers im Beton ist der Stahl normalerweise dauerhaft vor Korrosion geschützt. Unter ungünstigen Umgebungsbedingungen (Chlorideintrag, Carbonatisierung) kann die passive Deckschicht auf der Stahloberfläche zerstört werden. Der Korrosionsprozess ist initiiert. Die entstehenden Korrosionsprodukte werden zunächst vom Porengefüge des Betons aufgenommen, ohne dass es zu sichtbaren Schäden am Bauwerk führt. Im fortgeschrittenem Stadium der Korrosion können sich dann Risse und Abplatzungen bilden. Um notwendige Sanierungsmaßnahmen sowohl aus sicherheitstechnischen Gründen als auch aus wirtschaftlichen Erwägungen rechtzeitig einzuleiten, sind frühzeitige und weitestgehend zerstörungsfreie Prüfverfahren zur Ermittlung der aktuellen Korrosionswahrscheinlichkeit der Stahlbewehrung von großer Bedeutung. Deshalb finden Methoden und Verfahren zur laufenden bzw. regelmäßigen Korrosionsüberwachung von Stahlbetonbauwerken ständig größere Beachtung, sowohl im Bereich Forschung und Entwicklung als auch in der Praxis. Die elektrochemische Potentialfeldmessung ist ein etabliertes und weit verbreitetes Verfahren zur Beurteilung des Korrosionszustandes der Bewehrung in Stahlbetonbauwerken. Mit Hilfe dieses Verfahrens können Bereiche korrodierender Bewehrung zerstörungsfrei lokalisiert werden. In der Regel kommt diese Methode bei der Detektion von chloridinduzierter Korrosion zum Einsatz. Der Lehrgang vermittelt den Teilnehmenden in kompakter Form einen zusammenfassenden Überblick über die notwendigen Grundlagen zum Verständnis der Messmethode, der Vorbereitung und Durchführung der Messungen, der notwendigen Begleituntersuchungen sowie der Interpretation der gewonnenen Daten. Der erste Tag ist der theoretischen Ausbildung gewidmet, am zweiten Tag folgt dann die praktische Anwendung der Lerninhalte. Am dritten Tag folgt die Abnahme der praktischen und theoretischen Prüfung zur Erlangung des Sachkundenachweises. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen CY - Berlin, Germany DA - 24.04.2023 KW - Potentialfeldmessung KW - Korrosion PY - 2023 AN - OPUS4-57497 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - DIN 4871 N2 - Normative Anforderungen an ZfP-Prüfpersonal für ZfPBau sind in der DIN 4871 definiert. Die Ausbildung von Prüfpersonal für Potentialfeldmessung soll gemäß Norm zweistufig erfolgen. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen CY - Berlin, Germany DA - 24.04.2023 KW - Potentialfeldmessung KW - Korrosion PY - 2023 AN - OPUS4-57498 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Diercks, Philipp A1 - Veroy, K. A1 - Robens-Radermacher, Annika A1 - Unger, Jörg F. T1 - Multiscale modeling of heterogeneous structures based on a localized model order reduction approach N2 - Many of today’s problems in engineering demand reliable and accurate prediction of failure mechanisms of mechanical structures. Thus, it is necessary to take into account the heterogeneous structure on the smaller scale, to capture the underlying physical phenomena. However, this poses a great challenge to the numerical solution since the computational cost is significantly increased by resolving the smaller scale in the model. Moreover, in applications where scale separation as the basis of classical homogenization schemes does not hold, the influence of the smaller scale on the larger scale has to be modelled directly. This work aims to develop an efficient concurrent methodology to model heterogeneous structures combining the variational multiscale method (VMM) [1] and model order reduction techniques (e. g. [2]). First, the influence of the smaller scale on the larger scale can be taken into account following the additive split of the displacement field as in the VMM. Here, also a decomposition of the global domain into subdomains, each containing a fine grid discretization of the smaller scale, is introduced. Second, local reduced approximation spaces for the smaller scale solution are constructed by exploring possible solutions for each subdomain based on the concept of oversampling [3]. The associated transfer operator is approximated by random sampling [4]. Herein, we propose to incorporate the actual physical behaviour of the structure of interest in the training data by drawing random samples from a multivariate normal distribution with the solution of a reduced global problem as mean. The local reduced spaces are designed such that local contributions of each subdomain can be coupled in a conforming way. Thus, the resulting global system is sparse and reduced in size compared to the direct numerical simulation, leading to a faster solution of the problem. T2 - ECCOMAS YIC CY - Porto, Portugal DA - 19.06.2023 KW - Multiscale Method KW - Variational Multiscale Method KW - Domain Decomposition KW - Model Order Reduction PY - 2023 AN - OPUS4-58251 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Diercks, Philipp A1 - Veroy, K. A1 - Robens-Radermacher, Annika A1 - Unger, Jörg F. T1 - Physically meaningful samples in randomized local model order reduction N2 - In this contribution, a methodology for fine scale modeling of large scale structures is proposed, which combines the variational multiscale method[1], domain decomposition and model order reduction. The influence of the fine scale on the coarse scale is modelled by the use of an additive split of the displacement field, addressing applications without a clear scale separation. Based on the work of Buhr and Smetana[2], local reduced spaces are constructed by solving an oversampling problem with random boundary conditions. Herein, we inform the boundary conditions by a global reduced problem and compare our approach using physically meaningful correlated samples with existing approaches using uncorrelated samples. The local spaces are designed such that the local contribution of each subdomain can be coupled in a conforming way, which also preserves the sparsity pattern of standard finite element assembly procedures. Several numerical experiments show the accuracy and efficiency of the method, as well as its potential to reduce the size of the local spaces and the number of training samples compared to the uncorrelated sampling. T2 - XVII International Conference on Computational Plasticity, COMPLAS 2023 CY - Barcelona, Spain DA - 05.07.2023 KW - Domain Decomposition KW - Localized model order reduction KW - Multiscale method KW - Variational Multiscale Method PY - 2023 AN - OPUS4-58658 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Czeskleba, Denis A1 - Rhode, Michael A1 - Kannengießer, Thomas T1 - Kurzvorstellung des Projektes "H2SuD / Wasserstoff und Schweißen Einfluss des Schweißens auf die Wasserstoffaufnahme und Degradation im Betrieb befindlicher H2 Gasleitungen" N2 - Die Wasserstoffinfrastruktur ist eine zentraler Bestandteil der erfolgreichen Umsetzung der wasserstoffbasierten Energiewende. Dabei bilden Ferngasleitungen quasi das "Rückgrat" der Transportinfrastruktur großer Gasmengen. Dabei müssen unter Umständen Reparaturen an den Pipelines durchgeführt werden. Dabei ist in der Erdgasinfrastruktur das Schweißen an in Betrieb befindlichen (d.h. von Gas durchflossenen) Pipelines Stand der Technik. Es ist jedoch vollkommen offen, inwieweit diese Technik auf die reine Wasserstoffpipelines übertragbar sind. Hierzu leistet das Projekt H2SuD wichtige Beiträge zur Aufklärung des Einfluss eines Reparaturschweißprozesses auf die Wasserstoffaufnahme und Degradation im Betrieb befindlicher H2 Gasleitungen. T2 - Sitzung des FA1 "Schweißmetallurgie" der Forschungsvereinigung Schweißen und verwandte Verfahren des DVS e.V. CY - Aachen, Germany DA - 22.02.2023 KW - Wasserstoff KW - Pipeline KW - Reparatur KW - Schweißen KW - Ferngasleitung PY - 2023 AN - OPUS4-57087 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Deep foundations for offshore wind turbines - 1st part: axial behavior T1 - Cimentaciones profundas para aerogeneradores marinos. 1a parte: Comportamiento axial N2 - This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures. The first lecture presents a brief introduction to the context and peculiarities of such foundations, and then focuses on the particular case of axially loaded piles. This part is most relevant for the relatively slender piles of the multi-pile substructures (i.e. jackets and tripods). A clear distinction between physical phenomenology and practical design is drawn here. T2 - Masters course on Soil Mechanics and Geotechnical Engineering. Geotechnical Laboratory of CEDEX CY - Online meeting DA - 17.03.2023 KW - Pile foundations KW - Offshore wind turbines KW - Physical phenomenology KW - Design methods KW - Numerical modelling KW - Physical testing PY - 2023 AN - OPUS4-57176 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Design challenges for Offshore wind-farms. From foundation mechanics to wind-farm aerodynamics N2 - This talk provides a brief introduction on general engineering design challenges for the offshore wind energy production. Some general features of the offshore wind-energy field from a civil engineering perspective are firstly presented, followed by a brief discussion of some of the main geomechanical issues for the foundation of the offshore turbines into the seabed. In the following part, an overview of relevant fluid-structure interactions and some options for an efficient numerical analysis are provided, where the hydromechanical Wave–Tower interaction is firstly discussed. Then, some general aspects of the windfarm aerodynamics are introduced. On the one hand, some modelling possibilities for the wake analysis of single turbines and turbine groups are discussed. And on the other hand the relevance of such analyses for a proper windfarm layout optimization is pointed out. In particular, this talk shows that: i) The performance and behavior of the turbine's foundation is often conditioned by the appearance of large deformations, fluid couplings and grain-scale phenomena, whereby specific physical testing (both in field and lab conditions) and ad-hoc simulation techniques can provide useful insights for design; ii) Numerical analysis of a turbine’s interaction with wind/waves is already affordable in engineering scales, while simplified models can already provide a useful insight into the windfarm aerodynamics. iii) Turbulent wake analysis is very relevant for the windfarm layout. T2 - Colloquium "Energy systems compared", Winter semester 22/23, Faculty of Physics CY - Duisburg, Germany DA - 24.01.2023 KW - Offshore wind-turbine foundations KW - Water-structure interaction KW - Wind-farm aerodynamics PY - 2023 AN - OPUS4-56888 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Deep foundations for offshore wind turbines - 2nd part: lateral behavior & advanced topics T1 - Cimentaciones profundas para aerogeneradores marinos. 2a parte: Comportamiento Lateral + Temática avanzada N2 - This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures. The second lecture continues with the case of laterally loaded offshore piles, which bears most relevance for the case of the monopile foundations. Here again, a clear separation between physical reality and design methods is intended. Finally, the last part of the second lecture introduces several advanced topics which lie outside the classical design approaches, namely the hydromechanical coupling effects (i.e. the excess pore-pressure generation around the monopiles), the cyclic pile fatigue and the so-called pile setup (i.e. the time effects on the axial pile capacity). The relevance of the latter two topics is illustrated with experimental results from a field testing campaign on real large-scale piles. T2 - Masters course on Soil Mechanics and Geotechnical Engineering. Geotechnical Laboratory of CEDEX CY - Online meeting DA - 17.03.2023 KW - Pile foundations KW - Offshore wind turbines KW - Physical phenomenology KW - Design methods KW - Numerical modelling KW - Physical testing PY - 2023 AN - OPUS4-57178 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Costard, René A1 - Agasty, Amit A1 - Kadoke, Daniel A1 - Kind, Thomas A1 - Hicke, Konstantin A1 - Hüsken, Götz T1 - Charakterisierung der Belastung und Schädigung von Stahlbetonprüfkörpern unter Explosionsbeanspruchung N2 - Sprengversuche sind ein wesentliches Werkzeug, um die Eignung von Schutzobjekten und Bauteilen zum Schutz der Bevölkerung vor Anschlägen mit explosionsgefährlichen Stoffen wie Explosivstoffen, sogenannten „home-made-explosives“ (HME) und unkonventionellen Spreng- und Brandvorrichtungen (USBV) zu bewerten. Für forensische Zwecke werden oft Explosionsszenarien nachgebildet, um die Auswirkung von Anschlägen oder Unfällen genau untersuchen zu können. Feldversuche in Kombination mit numerischen Simulationen ermöglichen eine Charakterisierung der Belastung und Schädigung von Bauteilen und Strukturen unter hochdynamischen Explosionsbelastungen. Auf dem Testgelände Technische Sicherheit (TTS) der BAM in Horstwalde, Brandenburg werden Sprengversuche im Real-Maßstab durchgeführt. Dabei werden Bauteile mit Messtechnik ausgestattet, um eine dynamische Strukturcharakterisierung mittels sensorbasierten Monitorings zu ermöglichen. In diesem Vortrag werden am Beispiel einer Versuchskampagne mit einer Stahlbetonwand als Prüfkörper die Eignung verschiedener Prüfmethoden bei Sprengversuchen evaluiert. Es werden Messmethoden zur Charakterisierung der Explosionsereignisse, des globalen Strukturverhaltens sowie der lokalen Schädigung vorgestellt. Die direkte Charakterisierung der Explosionsbelastung erfolgt mit Hilfe von piezo-elektrischen Druckaufnehmern (bündig mit der Oberfläche im Prüfkörper montiert) und High-Speed-Kameras. Die Beobachtung der explosionsinduzierten Reaktion des Bauteils während und nach dem Eintreffen der Stoßwelle erfolgt mittels Beschleunigungssensoren, Stereo-Fotogrammetrie sowie mit in den Prüfkörper eingebetteter verteilter faseroptischer Sensoren, mit Hilfe derer die Dehnungsraten im Bauteil zeit- und ortsaufgelöst gemessen werden können. Die faseroptischen Sensoren erlauben außerdem die örtlich hochaufgelöste Bestimmung statischer Dehnungsänderungen im Bauteil nach einem Versuch, sodass auch nicht sichtbare Schädigungen wie kleinste Risse detektiert und charakterisiert werden können. Vergleichende Messungen mit Ultraschall komplettieren die Schadenscharakterisierung. In unserem Beitrag diskutieren wir die Herausforderungen dieser Messungen sowie die Ergebnisse und Möglichkeiten der genannten komplementären Messmethoden. T2 - 44. Informationstagung Sprengtechnik CY - Siegen, Germany DA - 14.04.2023 KW - Explosivstoffe KW - Sprengversuche KW - Schädigungscharakterisierung KW - Sensorik PY - 2023 AN - OPUS4-57319 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Camplese, D. A1 - Chianese, C. A1 - Scarponi, G. E. A1 - Eberwein, Robert A1 - Otremba, Frank A1 - Cozzani, V. T1 - Analysis of high temperature degradation of multi-layer insulation (MLI) systems for liquid hydrogen storage tanks N2 - The interest in hydrogen-based green energy is increasing worldwide, and the same is true for hydrogen-powered vehicles. Among the possible solutions to store hydrogen in such vehicles, cryogenic tanks equipped with multi-layer insulation (MLI) are the most promising to increase the amount of energy stored per unit volume. However, MLI is affected by severe deterioration when exposed to an external source of heat such as a fire following a car accident, leaving the tank unprotected and leading to failure in a relatively short time. In this work, a one-dimensional model to evaluate MLI thermal degradation when a liquid hydrogen tank is exposed to fire is presented. The relevance of taking MLI degradation into account when simulating the pressure increase due to external fire exposure is here demonstrated through the analysis of several case studies. The results show that MLI systems performance depletes within a few minutes of exposure to hydrocarbon poolfire. T2 - ICheaP 16 CY - Naples, Italy DA - 21.05.2023 KW - LH2 KW - MLI KW - Fire KW - Tank PY - 2023 AN - OPUS4-57553 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Stoljarova, A. A1 - Regenspurg, S. T1 - Influence Of Brine Precipitates On Materials Performance In Geothermal Applications N2 - Significant Cu-deposition and precipitation only occurred in combination with carbon steel. High-alloyed materials prevent the disturbing Cu-agglomeration. Pb-deposition and precipitation only occurred in combination with carbon steel. No negative Pb-effect could be observed in combination with high-alloyed steels. High alloyed corrosion resistant alloys are suitable and shall be chosen for future design of the piping system, either in massive or in cladded form, to prevent unwanted interactions with brine components. T2 - AMPP Annual 2023 Conference CY - Denver, CO, USA DA - 19.03.2023 KW - Geothermal KW - Electrochemistry KW - Copper KW - Lead KW - Corrosion PY - 2023 AN - OPUS4-57237 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas A1 - Lehmann, Jens A1 - Müller, Thoralf T1 - Korrosionsarten an geschweißten Bauteilen aus Cr-Ni-Stahl N2 - Die Bedingungen für den schadensfreien Einsatz nichtrostender Stähle, nicht nur bei Schweißverbindungen, sind: 1) Die Passivschicht muss sich vollständig ausbilden können. Voraussetzung dafür sind glatte, blanke, saubere Oberfläche, eine gleichmäßige Elementverteilung, wenig Ausscheidungen und Verunreinigungen. Eine mögliche Beeinflussung der Gefügeausbildung durch Warmumformung und durch die schweißtechnische Verarbeitung sind zu beachten. Anlauffarben müssen durch geeignete geeignete chemische bzw. mechanische Nachbehandlung entfernt werden. 2) Die Repassivierung von Defektstellen unter Einsatzbedingungen muss möglich sein, was durch geeignete Werkstoffauswahl und die Legierungszusammensetzung sicherzustellen ist. Unplanmäßige Betriebszustände oder Störungen können kritische Systemzustände hervorrufen, die die Repassivierung beeinträchtigen oder verhindern. Eine geeignete Unterhaltsreinigung ist sicherzustellen. T2 - Weiterbildung DVS Bezirksverband Chiemgau CY - Trostberg, Germany DA - 02.03.2023 KW - Nichtrostender Stahl KW - Korrosionsverhalten KW - Verarbeitung KW - Fehlerquellen PY - 2023 AN - OPUS4-57150 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Biyikal, Mustafa T1 - Development of a Handheld Device for the Trace Detection of Explosives N2 - With the help of the EXIST research transfer the startup True Detection System (TDS) will develop a portable and easy-to-use handheld device based on chemical-optical sensors that can detect the smallest traces of various explosives and markers (e.g. TNT, C4, ANFO, TATP, DMDNB, etc.) and pure salts (e.g. potassium nitrate) reliably and without major cross-sensitivities. The device has been developed over the last 10 years at the Federal Institute for Material Research and Testing (BAM) in cooperation with an SME. Within the next 18 months, a laboratory prototype will now be converted into a commercial device. T2 - Photonics Days Berlin Brandenburg CY - Berlin, Germany DA - 09.10.2023 KW - Explosives KW - Trace detection KW - Handheld device KW - Lab-on-a-chip KW - Start-up PY - 2023 AN - OPUS4-58541 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Birk, A. M. A1 - Bradley, I. A1 - Bisby, L. A1 - Otremba, Frank A1 - Borch, Jörg T1 - Optical Access Pressure Vessel for Observing Temperature Stratification and Boiling in a Pressure Vessel Exposed to Accidental Fire N2 - We are interested in accidental fire impingement of HazMat pressure vessels. Want to develop improved models for predicting time to failure or empty (if PRV present). We are still trying to properly predict pressurization and time to first PRV activation due to liquid temperature stratification for a range of fire scenarios (Full and partial engulfing pool fire, jet fires, with roll over, with TP defects, etc.) T2 - Optical Access PV for Fire Effects Research CY - Berlin, Germany KW - Vessels KW - Observing temperatur KW - Accidential Fire PY - 2023 AN - OPUS4-57565 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Soil-foundation-structure problems related to train induced vibrations - the kinematic interaction of tunnel excited pile foundations and the inertial interaction of high rise buildings N2 - The soil-foundation-structure interaction is always important when building vibrations due to train passages have to be considered. The frequency range for train vibrations is up to 100 Hz. Normally, soft surface soils are crucial so that the wavelength can be much smaller than the foundation dimensions. Three topics are of interest for the prediction and the under-standing of building vibrations. 1. The „kinematic interaction“ or the „added foundation ef-fect“, which is calculated either by the combined boundary-element finite-element method or by the wavenumber domain method, results in a reduction of the free-field vibration. The stiff-ness of the foundation resists the wave deformation, plates and walls for horizontally propa-gating waves or piles for vertically incident waves. 2. The „inertial interaction“ or the „added building effect“ yields an amplification around the vertical building resonance, which may be a rigid mode on the compliant soil or a flexible mode for high-rise buildings, and a reduction at higher frequencies. This has been analysed by detailed finite element models of apartment and office buildings. 3. Base isolation is a method to further reduce building vibrations. It is important to know the soil-foundation impedance for the possible reduction, as well as the correct building impedance. A high-rise building cannot be considered as a rigid mass model. It has a frequency-dependent behaviour with longitudinal waves travelling from the founda-tion to the top of the building which include the effect of floor vibrations. Experiences from building projects in Vienna, Frankfort and Berlin will give some additional results for the ex-citation from tunnel lines, the kinematic response of pile foundations, and the inertial re-sponse of the flexible multi-storey buildings. T2 - Computational Methods in Structural Dynamics and Earthquake Engineering (COMPDYN 2023) CY - Athens, Greece DA - 12.06.2023 KW - Soil-pile interaction KW - Pile groups KW - Kinematic interaction KW - Inertial interaction KW - High-rise buildings KW - Base isolation PY - 2023 AN - OPUS4-57954 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Some resonance effects of non-typical trains and railway bridges investigated by a frequency-domain method N2 - The resonances of railway bridges have often been analysed for short bridges under periodical high-speed trains, for simply supported one-span bridges, for the fundamental bridge mode, and by time-domain analyses. Many time-consuming calculations have been performed to establish simplified rules for standards. In this contribution, the passage of different (existing, new and hypothetic) trains over different bridges will be analysed in frequency domain by using three separated spectra with the purpose to get a better physical insight in the phenomena. At first, the excitation spectrum of the modal forces is built by the mode shape and the passage time of the train over the bridge. The second spectrum is the frequency response function of the bridge which include the modal frequency, damping and mass. The third part is the spectrum of the axle sequence of an arbitrary train which is not limited to periodical or specific (conventional, articulated, regular or standard) trains and which does not include any bridge parameters. The final solution in frequency domain is obtained as the product of these three complex, strongly varying spectra for the dominating bridge mode or in general as the sum of these products over all relevant bridge modes. The time domain solution is obtained via the inverse Fourier transform, and the resulting time histories have been successfully compared with some measurement results. The method is applied to the vertical and torsional modes of a mid-long 1-span bridge on elastomeric bearings under standard train speeds, and to a long multi-span integral bridge under long periodical freight trains. Different resonance and cancellation effects have been found for systematically varied train speeds according to the axle sequence of the whole train which is dominated by the two locomotives in that case. To be more specific, the first torsional mode of the mid-span bridge is excited for a train speed of 100 km/h whereas the second bending mode is excited for a train speed of 160 km/h. In both cases, the other mode is suppressed by the minima of the axle-distance spectra. In addition, the case of the German high-speed train ICE4 and the very high-speed hyperloop case will be discussed briefly. In general, it is shown that resonance effects are also worth to be studied for freight and passenger trains with lower speeds. T2 - EURODYN 2023 XII International Conference on Structural Dynamics CY - Delft, Netherlands DA - 03.07.2023 KW - Railway bridge KW - Transfer fuction KW - Modal load spectrum KW - Axle-sequence spectrum KW - Freight train KW - Passenger train KW - High-speed train KW - 2-span bridge PY - 2023 AN - OPUS4-57955 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Train-induced ground vibrations – The emission and transmission from tunnel and surface lines N2 - Train-induced ground vibrations are quite different for tunnel and surface lines. The excitation of the track and ground vibration by the vehicle-track-soil interaction maybe influenced by the stiffer track support of the tunnel invert. The excited waves are propagating on a different path compared to the surface line. The wave propagation in the interior of the soil is calculated by a wavenumber integral in a similar way as the propagation along the surface and a general reduction of < 0.5 has been found. An additional reduction has been found because of the missing Rayleigh wave. The different excitation of tunnel lines is analysed theoretically by the combined finite-element boundary-element method and some results about the influencing tunnel and soil parameters will be shown. Measurements have been made at the Mühlberg-Tunnel in Germany. The vibrations of the train, the track and the soil have been measured simultaneously at the tunnel and a nearby surface line. Spectra will be shown for different train speeds between 60 and 160 km/h. A clear reduction effect for the tunnel line compared to the surface line has been observed in a specific (train-speed-dependent) frequency range. This agrees well with the observations of other research institutes. The mid-frequency tunnel-surface reduction seems to be a consequence of the stiffer track structure which leads to a wider distribution of the axle loads. Therefore, the axle impulses due to the train passage are longer and have a lower frequency content. This will have an effect on the ground vibrations at some distance which are present in case of an irregular transmission path through a ballast and soil with varying stiffness. A similar reduction effect can also be found for other track forms where the axle impulses are distributed on a longer track segment, for example slab tracks, tracks with under ballast plates, under ballast mats or under sleeper pads. T2 - 29th International Congress on Sound and Vibration (ICSV29) CY - Prague, Czech Republic DA - 09.07.2023 KW - Ground vibration KW - Railway tunnel KW - Layered soil KW - Surface-tunnel reduction KW - Measurements PY - 2023 AN - OPUS4-57956 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Prognoseverfahren für Bahnerschütterungen – DIN 45672-3, VDI 3837, HighSpeed2 und die Fahrzeug-Fahrweg-Boden Wechselwirkung N2 - Die VDI Richtlinie 3837 enthält detaillierte Angaben zur Erschütterungsemission. Die DIN 45672-3 enthält nur den Tunnel- oder einen Bodenmesspunkt als Ausgangspunkt der Prognose. Die Erschütterungsanregung durch die Fahrzeug-Fahrweg-Wechselwirkung wird beschrieben. Die ERgebnisse der BAM stimmen sehr gut mit dem Prognosekonzept von Highspeed 2 überein. Dies wird an den Punkten 1. Störgrößen, 2. Achsimpulse, 3. Tunnelstrecken aufgezeigt. T2 - Norm-Arbeitsausschuss Schwingungsminderung in der Umgebung von Verkehrswegen CY - Frankfurt/M., Germany DA - 08.02.2023 KW - Normung KW - Bahnerschütterungen KW - Emission KW - Fahrzeug-Fahrweg-Boden-Wechselwirkung KW - Störgrößen KW - Achsimpulse KW - Tunnelstrecke PY - 2023 AN - OPUS4-56978 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz A1 - Said, Samir T1 - Damage detection by flexibility functions and quasi-static moving load tests N2 - The contribution shows measurement examples of cars, floors, foundations, railway tracks, a footbridge, and a railbridge. Vibrations may include modes and waves. Namely in soil-structure interaction, modes are damped, shifted and prevented so that alternatives for the modal analysis are necessary: The approximation of the whole spectrum (flexibility function) and of the whole train passage (moving-load response). T2 - Symposium Emerging Trends in Bridge Damage Detection, Localization and Quantification CY - Luxembourg, Luxembourg DA - 05.05.2023 KW - Flexibility KW - Movin load test KW - Frequency response function KW - Cars KW - Floors KW - Foundations KW - Railway tracks KW - Footbridge KW - Railbridge KW - Damage detection PY - 2023 AN - OPUS4-57951 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Frequenz- und bodenabhängige Prognose und Minderung von Bahnerschütterungen N2 - Die Prognose und Minderung von Bahnerschütterungen haben eine lange Tradition in der Bundesanstalt für Materialforschung und -prüfung. Im Jahr 2006 wurde eine Prognose-Software fertiggestellt, die viele Forschungs- und Messergebnisse zusammenfasst. Sie umfasst die Teilbereiche Emission (die Anregung durch die Fahrzeug-Fahrweg-Untergrund-Wechselwirkung), die Transmission (die Ausbreitung durch den Boden) und die Immission (die Übertragung vom Freifeld in ein Gebäude). Die Prognose geschieht in allen Teilen mit einfachen Formeln, die veröffentlicht sind und zur Anwendung für Jedermann zur Verfügung stehen. Es werden Beispiele zur Emission und zur Transmission gezeigt. Im Bereich Transmissionsprognose werden zu den Anregungskräften (aus dem Emissionsteil) die Bodenerschütterungen als Schwinggeschwindigkeitsterzspektren berechnet. Das Ergebnis hängt stark von der Bodensteifigkeit, -dämpfung und -schichtung ab. Dies wurde später mit einer Messkampagne in der Schweiz an 10 Messorten bestätigt (Bild 1). Die Berechnung erfolgt näherungsweise für einen geschichteten Boden mit einer frequenzabhängigen Wellengeschwindigkeit (Dispersion) oder einem tiefenabhängigen Wellengeschwindigkeitsprofil. Die Anregungskräfte werden im Prognosebereich Emission mit einem 2-dimensionalen Gleismodell berechnet (Bild 2). 1-dimensionale Modelle liefern meist falsche Ergebnisse und 3-dimensionale Modelle (zum Beispiel mit der kombinierten Finite-Element-Randelement-Methode) sind für eine Erschütterungs¬prognose sicherlich zu aufwändig. Das 2-dimensionale Modell wurde an 3-dimensionale Ergebnisse so angepasst, dass die Ergebnisse für viele Gleise und Böden annähernd zutreffen. Auch Minderungs¬maßnahmen am Gleis können mit diesem Modell sehr gut berechnet werden. Die Prognoseverfahren wurden in den folgenden Jahren weiter verfeinert. Es wurde die quasi-statische Anregung durch die bewegten statischen Zuglasten mit einer Näherungsformel ergänzt, so dass auch das tieffrequente Nahfeld realistisch erfasst werden kann. Mit der Berücksichtigung der Achsfolge (insbesondere zwischen den Achsen im Drehgestell) ergeben sich zwei typische Minima in den Erschütterungsspektren, die oft auch in den Messungen beobachtet werden. Der Amplitudenanteil zwischen diesen beiden Minima ist oft stärker angehoben, so dass hier eine zusätzliche Erschütterungsanregung vermutet wird. Dieser Anteil kann rein empirisch prognostiziert werden, so wie das in den englischen Prognosen (zuletzt für das Highspeed2-Projekt) enthalten ist. Die Begründung dieses Anteils ist allerdings nicht die Achsfolge, sondern die Zerstreuung der statischen Achslastimpulse durch einen unregelmäßigen Gleisuntergrund und Boden. Die messtechnische Ermittlung eines Minderungseffektes ist komplizierter als allgemein angenommen. Es reicht nicht aus, jeweils an einem Messpunkt in der Nähe eines Gleises mit und ohne Minderungs¬maßnahme die Erschütterungen zu messen und aus dem Verhältnis der Amplituden (beziehungsweise aus der Differenz der Pegel) „die Einfügedämmung“ zu ermitteln. Es wird an Beispielen gezeigt, wie man hier sinnvoller vorgehen kann. 1. Zunächst ist es wichtig, nicht nur die Einfügedämmung sondern auch die Originalspektren mit und ohne Minderung zu dokumentieren und zu veröffentlichen, damit man kontrollieren kann, ob wesentliche Amplituden und Frequenzbereiche reduziert sind oder ob es sich um eher zufällige Minderungen oder Verstärkungen handelt. (Beispiel Unterschottermatte/Raron, Müller/SBB) 2. Der Messpunkt sollte nicht im Nahbereich des Gleises liegen, da ansonsten eine zu günstige, falsche Einfügedämmung bestimmt wird. (Beispiel Tunnel/ Leipzig/Breitsamter) 3. Um Zufälligkeiten zu vermeiden, sollte man an mehr als einem Punkt messen. (Beispiel Unterschotterplatte/Altheim/Auersch) 4. Man sollte eigentlich immer auch die Bodenkennwerte (Steifigkeit, Dämpfung, Amplituden-abnahme, Übertagungsfunktion) messen. Selbst bei nahegelegene Messquerschnitten kann man Überraschungen erleben. (Beispiel erste ICE-Messungen/bei Würzburg/Auersch) 5. Bei verschiedenen Bodenkennwerten kann man eine Korrektur durchführen. (Beispiel Gleis-tröge/Mistler) Am besten bestimmt man ein äquivalentes Kraftspektrum zu jedem Messort und jedem Messzug (Beispiel Feste Fahrbahn/Gardelegen/Auersch) 6. Prinzipiell gibt es nicht die Einfügedämmung einer Maßnahme. Die Einfügedämmung ist immer boden- und referenzsystemabhängig. Die „beste“ Einfügungsdämmung erhält man mit einem steifen Untergrund (Beispiel Unterschottermatte/Tunnel/München Gasteig/Wettschureck) Das heißt aber nicht, dass die Maßnahme durch einen künstlich versteiften Untergrund besser wird (Beispiel Unterschottermatten/RRT2006/Auersch) Es werden Messbeispiele gezeigt, die alle neben einer hochfrequenten dynamischen Minderung auch eine mittelfrequente quasi-statische Minderung aufweisen. Dabei wird der mittelfrequente Zerstreuanteil der statischen Achslastimpulse durch die breitere Lastverteilung und damit die Impulsdehnung der Achslastimpulse reduziert. Diese Impulsdehnung lässt sich mit dem 2-dimensionalen Gleismodell berechnen. Die Minderungswirkung hängt aber wiederum vom Referenzsystem und dessen unregel¬mäßiger Steifigkeitsverteilung ab. Je unregelmäßiger der Boden und Gleisuntergrund des Referenz¬systems, desto stärker ist die Minderungswirkung. T2 - 24. Symposium für Baudynamik und Erschütterungsmessungen CY - Dübendorf, Switzerland DA - 09.06.2023 KW - Bahnerschütterungen KW - Erschütterungsprognose KW - Erschütterungsminderung KW - Elastische Gleiselemente KW - Gleiströge KW - zerstreute Achslastimpulse PY - 2023 AN - OPUS4-57952 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Impacts between different drop masses and different targets in different scales N2 - The Federal Institute of Material Research and Testing has performed many impact tests from very small laboratory tests to very big “free-field” tests with heavy containers on stiff foundations. The first measurements have been done on a big foundation where it should be guaranteed that the foundation is rigid and the container is tested properly. Later on, a smaller drop test facility has been built on the ground inside an existing building. It had to be controlled by prediction and measurements that the drop test will not damage the building. Tests from different heights on soft, medium, and stiff targets have been done to find out rules which allow to identify acceptable and unacceptable drop tests. Later on, the biggest drop test facility has been built for masses up to 200 t. It was necessary for the design of the foundation to estimate the forces which oc-cur during the drop tests. In addititon, the acceptable tests should be selected and controlled by measurements where the impact duration is important. Dif-ferent sensors, accelerometers, accelerometers with mechanical filters, geo-phones (velocity transducers), strain gauges, and pressure cells have been ap-plied for these tasks. Signal transformations and model calculations have been used to check and understand the dynamic measurements. The simplest law is the conservation of the momentum which is a good approximation if the impact is short. If the soil under the foundation has an influence on the deceleration of the container, the maximum foundation velocity is lower than the simple esti-mation. T2 - 10th International Conference on Experimental Vibration Analysis for Civil Engineering Structures CY - Milano, Italy DA - 30.08.2023 KW - Drop test KW - Vibration measurements KW - Container loading KW - Foundation load PY - 2023 AN - OPUS4-58504 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Andrés Arcones, Daniel A1 - Weiser, M. A1 - s Koutsourelakis, F. A1 - Unger, Jörg F. T1 - A Bayesian Framework for Simulation-based Digital Twins of Bridges N2 - Simulation-based digital twins have emerged as a powerful tool for evaluating the mechanical response of bridges. As virtual representations of physical systems, digital twins can provide a wealth of information that complements traditional inspection and monitoring data. By incorporating virtual sensors and predictive maintenance strategies, they have the potential to improve our understanding of the behavior and performance of bridges over time. However, as bridges age and undergo regular loading and extreme events, their structural characteristics change, often differing from the predictions of their initial design. Digital twins must be continuously adapted to reflect these changes. In this article, we present a Bayesian framework for updating simulation-based digital twins in the context of bridges. Our approach integrates information from measurements to account for inaccuracies in the simulation model and quantify uncertainties. Through its implementation and assessment, this work demonstrates the potential for digital twins to provide a reliable and up-to-date representation of bridge behavior, helping to inform decision-making for maintenance and management. T2 - EUROSTRUCT 2023 CY - Vienna, Austria DA - 25.09.2023 KW - Digital Twin KW - Simulation Models KW - Uncertainty Quantification KW - Model Bias PY - 2023 UR - https://eurostruct.org/eurostruct-2023/ AN - OPUS4-58663 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Andres Arcones, Daniel A1 - Weiser, M. A1 - Koutsoureladkis, D.-S. A1 - Unger, Jörg F. T1 - Evaluation of Model Bias Identification Approaches Based on Bayesian Inference and Applications to Digital Twins N2 - In recent years, the use of simulation-based digital twins for monitoring and assessment of complex mechanical systems has greatly expanded. Their potential to increase the information obtained from limited data makes them an invaluable tool for a broad range of real-world applications. Nonetheless, there usually exists a discrepancy between the predicted response and the measurements of the system once built. One of the main contributors to this difference in addition to miscalibrated model parameters is the model error. Quantifying this socalled model bias (as well as proper values for the model parameters) is critical for the reliable performance of digital twins. Model bias identification is ultimately an inverse problem where information from measurements is used to update the original model. Bayesian formulations can tackle this task. Including the model bias as a parameter to be inferred enables the use of a Bayesian framework to obtain a probability distribution that represents the uncertainty between the measurements and the model. Simultaneously, this procedure can be combined with a classic parameter updating scheme to account for the trainable parameters in the original model. This study evaluates the effectiveness of different model bias identification approaches based on Bayesian inference methods. This includes more classical approaches such as direct parameter estimation using MCMC in a Bayesian setup, as well as more recent proposals such as stat- FEM or orthogonal Gaussian Processes. Their potential use in digital twins, generalization capabilities, and computational cost is extensively analyzed. T2 - 5th ECCOMAS Thematic Conference on Uncertainty Quantificationin Computational Sciences and Engineering CY - Athens, Greece DA - 12.06.2023 KW - Digital Twin KW - Simulation Models KW - Uncertainty Quantification KW - Model Bias PY - 2023 UR - https://2023.uncecomp.org/ AN - OPUS4-58226 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit A1 - Costard, René A1 - Rosenbusch, Sjard Mathis A1 - Kadoke, Daniel A1 - Kind, Thomas A1 - Hicke, Konstantin A1 - Hüsken, Götz T1 - Structural behavior and damage assessment of a reinforced concrete wall by various NDT methods and embedded sensors under blast-loading N2 - A safety or security related assessment of explosions, accidental and intentional scenarios alike, often necessitate performance of replication-tests. Such test results are necessary to clarify the causes within the scope of forensic investigations. To gain important insights into the behavior of structures and materials under such loading, field tests may also be performed in accordance with different test standards. To determine the resistance of building-structures after explosions, estimation of the residual load-bearing capacity in addition to the assessment of dynamic structural response and damage to the building components is important. In most cases an evaluation of structural integrity is based only on the visual damage, resulting in an overestimation of the residual capacity. The Bundesanstalt für Materialforschung und -prüfung (BAM) operates the Test site for Technical Safety (TTS) on an area measuring about 12 km2 in the Federal State of Brandenburg for execution of true-to-scale explosion tests. At the TTS, building component testing was performed to assess the suitability of different non-destructive testing methods to characterize the dynamic structural response and damage resulting from the detonation of high explosives. Different blast-loading scenarios were realized by varying the net explosive mass and the standoff distance with all scenarios representing a near-field detonation. The test object was a reinforced concrete wall 2 m high, 2.5 m wide and 20 cm thick, fixed at both vertical edges. The dynamic loading of the wall was characterized with 8 piezoelectric pressure sensors flush-mounted on the front surface, thus measuring the reflected pressures from the shock wave. The tests were conducted with the aim of characterizing the global behavior of the wall under dynamic shock loading and the resulting local damage pattern, respectively. High speed digital image correlation was implemented in combination with multiple acceleration sensors to observe the rear surface of the wall to chart the dynamic deflection during the loading and to determine the residual deformation after the loading had ceased. In addition, one test specimen was instrumented with fiber optic sensor cables, both fixed to the rebars and embedded in the concrete-matrix, respectively. Firstly, these sensors were interrogated during the blast test by a distributed acoustic sensing (DAS) device using a particularly high sampling rate to measure the shock-induced vibrations in the structure with high temporal resolution. This delivers information on dynamics of compression and tension cycles from within the structure. Secondly, the local damage-pattern emerging during the series of blasts was determined via distributed fiber optic strain sensing (DSS) by interrogating the embedded fiber optic sensors with a high spatial resolution DSS device after each blast. This enabled the characterization of non-visual damage to the structure, in particular with regard to the formation of localized cracks in the concrete matrix. The DSS was further complimented by a structure-scanner based on ultrasonic measurements. Our contribution describes this new test approach in detail. Results of the three datasets, namely dynamic shock loading, global behavior of the test object and the local damage pattern will be presented. The suitability of the implemented measurement methods will be discussed in combination with the challenges in their application for technical safety evaluation of building components under explosive loading. T2 - 26th International Symposium on Military Aspects of Blast and Shock (MABS26) CY - Wollongong, Australia DA - 03.12.2023 KW - Blast tests KW - Reflected pressure KW - Embedded sensors KW - Distributed fiber optic sensors KW - Acceleration sensors KW - Digital image correlation KW - Ultrasonic structure-scanner PY - 2023 AN - OPUS4-58927 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit A1 - Rosenbusch, Sjard Mathis A1 - Costard, René T1 - Numerical analysis of structures under blast loading N2 - Blast tests are indispensable for investigations of accidental or intentional explosions and to evaluate the level of protection to people and equipment within critical infrastructure. Current capabilities for detailed blast effects assessment are limited to performing full-scale field testing, which, for complex scenarios, are highly resource intensive. In this regard, reliable numerical simulations are an effective alternative option. A discussion of the scope and challenges of using numerical tools for a technical-safety assessment of reinforced concrete structures under blast loading is presented. Different coupling possibilities between shock wave simulations and structural simulations with the help of practical examples is given. An outlook on the development of new methods for structural simulations currently being researched at BAM concludes the presentation. T2 - Exerter Final Conference, 2023 CY - Soest, The Netherlands DA - 24.04.2023 KW - Coupling KW - Numerical Simulation KW - Blast KW - Structural Analysis KW - FSI PY - 2023 AN - OPUS4-57458 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -