TY - CONF A1 - Hofmann-Böllinghaus, Anja T1 - Fire safety of façades with polystyrene foam insulation N2 - Several fires involving ETIC (external thermal insulation composite) systems with polystyrene foam insulation in Germany led to an extensive discussion about fire safety of such systems. A collection initiated by the Frankfurt fire service of façade fires which include polystyrene insulation foam shows that especially fires which started in front of the buildings led to more severe fires of the façade than fires that started inside the buildings. In several fires the ignition source were burning waste containers. Three large scale tests which were initiated by German building ministries showed weaknesses of the existing systems when challenged by a bigger fire source in front of the façade. Since then measures have been introduced to enhance these systems and an additional test with a 200 kg wood crib in front of a large test rig has been used for approval of ETICS. However, the recently introduced German draft standard DIN E 4102-20 does not take these changes into account although real cases and the large scale tests showed that fire scenarios with a bigger ignition source as a waste container are not covered by the DIN E 4102-20. Numerical investigations show that regarding the heat flux to the area above the opening (e.g. a window) also only a fraction of real fires is covered. Additionally damaged systems have been investigated using the Single Burning Item (SBI) test with higher heat release rates of the burner. The damage significantly influenced the fire development of the specimen. Collapse of a damaged coating of an ETIC system occurred during the test and had a sudden fire growth as a result as the whole specimen was suddenly on fire. Several effects which could be seen in the intermediate scale tests correspond to observations which were made in the real cases. In Germany insulation of existing buildings is often enhanced with application of ETICS. In most cases the buildings are in use at the time when the construction takes place. At several stages of the construction process large amounts of unprotected polystyrene are stored in immediate proximity of the building and unprotected polystyrene can be in place on the façade for several weeks. As a consequence of the investigations challenges and possible measures to enhance fire safety of ETIC systems are discussed. T2 - Interflam Konferenz 2016 CY - Royal Holloway College, London, UK DA - 4.7.2016 KW - ETICS KW - Polystyrene KW - Insulation KW - Fire safety PY - 2016 AN - OPUS4-37011 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geoerg, Paul T1 - Evacuation dynamics under consideration of vulnerable pedestrian groups N2 - The understanding of human behavior during evacuation processes is an important matter to improve the safety of infrastructures. In many countries, the implementation of performance based codes enables fire safety engineers to use computer based calculation tools to predict and evaluate pedestrian movement and human behavior in buildings. The models are based on experimentally obtained parameters and theoretical models. Pedestrian behavior can be influenced by the characteristics of the buildings (e.g. type of the building) as well as the characteristics of individuals and the pedestrian group. This paper shows that the approach of Required Safe Egress Time (RSET) / Available Safe Egress Time (ASET) is imprecise with regard on heterogeneous pedestrian groups, because this concept completely neglected the variability’s in individual pre-movement and movement abilities. T2 - Interflam CY - Royal Holloway College, London, UK DA - 04.07.2016 KW - Evacuation KW - Vulnerable groups KW - Simulation KW - Egress PY - 2016 AN - OPUS4-36822 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Abdelkhalik, A. A1 - Askar, Enis A1 - Markus, D. A1 - Brandes, E. A1 - El-Sayed, I. A1 - Hassan, M. A1 - Nour, M. A1 - Stolz, T. T1 - Explosion regions of propane, isopropanol, acetone, and methyl acetate/inert gas/air mixtures N2 - The explosion regions for propane, isopropanol, acetone, and methyl acetate with air in the presence of nitrogen, argon, helium, and carbon dioxide were determined experimentally according to EN 14756/EN1839, method T. Except for propane, all the measurements were executed at 323 K and 1 bar. Propane experiments were carried out at 293 K and 1 bar. The results show that for the same type of inert gas, propane, isopropanol, and acetone have great closeness concerning the concentration of the inert gas at the apex of the explosion envelope in a ternary diagram with air as oxidizer. This leads to consistency in the limiting oxygen concentration (LOC) and minimum required amount of inert gas (MAI) values. Concerning methyl acetate, the apex was always reached at higher percentages of inert gases compared with the other fuels. This can be attributed to the presence of two oxygen atoms inside the chemical structure. Calculation of the explosion regions was carried out based on calculated adiabatic flame temperature (CAFT) method. The flame temperatures for the experimentally determined fuel/air/N2 mixtures were calculated. Then, these temperatures were used to predict the explosion limits of similar mixtures with other inert gases than nitrogen. The modeling results show reasonable agreement with the experimental results. KW - Flammability limits KW - Model of constant adiabatic flame temperatures (CAFT) KW - Inertisation KW - Explosion protection PY - 2016 DO - https://doi.org/10.1016/j.jlp.2016.04.001 SN - 0950-4230 VL - 2016/43 SP - 669 EP - 675 PB - Elsevier Ltd. CY - Oxford, UK AN - OPUS4-37996 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias A1 - Simon, Patrick ED - Cunha, Álvaro ED - Caetano, Elsa T1 - Review of Ballasted Track Destabilization on Shake Table Tests N2 - Shake table tests have been used for a long time to understand the densification and fluidization of granular materials. While purely vertical shaking is quite unlikely to be found in vibration analysis when it comes to granular materials as soils, it has been found that the vertical vibration of railway bridge support structures can affect the fabric of the ballasted track on top. Starting from the experience at French railway lines with destabilizing track conditions on short bridges in high speed lines in the 1990s, various shake table test configurations have been used to investigate the destabiliza-tion of ballast at high acceleration levels. This article describes the effects of the variously investigated dynamic excitations of railway bridges on the bal-lasted track itself. T2 - 11th International Conference on Experimental Vibration Analysis for Civil Engineering Structures (EVACES 2025) CY - Porto, Portugal DA - 02.07.2025 KW - Infrastructure KW - Ballasted track KW - Ballast KW - Railway bridge dynamics PY - 2025 SN - 978-3-031-96105-2 DO - https://doi.org/10.1007/978-3-031-96106-9_62 SP - 595 EP - 604 PB - Springer CY - Cham AN - OPUS4-64265 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Characteristic Frequencies of Train-Induced Bridge, Track, Ground and Building Vibrations – Excitation and Mitigation N2 - The characteristic frequencies of train-induced vibrations are discussed in theory and experiment following the propagation of vibrations from the source to the receiver: 1. Out-of-roundness frequencies of the wheels, 2. sleeper-passage frequency, 3. the vehicle-track eigenfrequency, 4. band frequency of the impulses of the passing static axle loads, 5. car-length frequency and multiples, 6. axle-distance frequencies with two characteristic zeros, 7. bridge eigenfrequencies, 8. the cut-on frequency due to the layering, and 9. the cut-off frequency due to the material damping of the soil, 10. the building-soil eigenfrequency, 11. as a rigid building or flexible wall/column mode, 12. floor eigenfrequencies, 13. acoustic room resonances, 14. the „resonance“ frequency or cut-off frequency of a base isolation. Coincidences of some of these characteristic frequencies or frequency ranges can be typically problematic and mitigation measures at the track or at the building can be necessary. The bridge response to the passing static loads is deter¬mined by the axle-sequence spectrum, the eigenfrequency (transfer function) of the bridge, and the modal force or mode shape spectrum. The ground vibration has typically high frequencies for a stiff soil and low frequencies for a soft soil. The high amplitudes between the zeros of the axle-sequence spectrum are often measured in the ground vibrations, and they can be mitigated by soft support elements or a higher bending stiffness of the track. T2 - EVACES 2025 CY - Porto, Portugal DA - 02.07.2025 KW - Train-induced vibration KW - Vehicle excitation KW - Track response KW - Bridge resonance KW - Ground vibration KW - Soil-building transfer KW - Floor resonance KW - Axle-sequence spectrum KW - Vehicle-track eigenfrequency KW - Axle impulses PY - 2025 SN - 978-3-031-96113-7 DO - https://doi.org/10.1007/978-3-031-96106-9_77 VL - 2025 SP - 1 EP - 8 PB - Springer CY - Cham, Schweiz AN - OPUS4-63655 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Patrick A1 - Baeßler, Matthias ED - Cunha, Álvaro ED - Caetano, Elsa T1 - On the reassessment of bridge superstructure vibrations for high-speed traffic N2 - The acceleration thresholds of bridge superstructures remain critical for designing and reassessing railway bridges on high-speed lines, with ballasted track systems historically limited to 3.5 m/s2 vertical accelerations due to destabilization risks. As part of the European InBridge4EU project, this study addresses methodological uncertainties in linking vertical bridge vibrations to lateral track creep—a key focus area for modernizing assessment protocols. A comparative analysis of two acceleration postprocessing methods (peak identification vs. fatigue-derived rainflow counting) as part of a recently proposed framework was conducted using an example bridge and train combination. Results demonstrate that rainflow counting yields more conservative creep estimates with the bulk of cumulative vibration-induced creep attributable to accelerations exceeding 3 m/s2. However, discretizing acceleration ranges into 1 m/s2 bins introduced significant errors compared to continuous cycle data, highlighting sensitivity to analysis parameters. These findings underscore the complexity of reconciling laboratory-derived harmonic vibration models with real-world bridge dynamics, where non-uniform acceleration patterns dominate. The research directly informs ongoing efforts to refine standardized criteria for ballasted track stability, particularly through the InBridge4EU project’s systematic re-evaluation of vibration limits and their engineering implications. By quantifying discrepancies between computational approaches, this work advances the development of robust protocols for predicting track degradation under high-speed operational loads. T2 - 11th International Conference on Experimental Vibration Analysis for Civil Enginering Structures (EVACES 2025) CY - Porto, Portugal DA - 02.07.2025 KW - Infrastructure KW - Railway bridges KW - Ballast destabilization KW - Acceleration limit KW - Ballasted track KW - Rainflow counting PY - 2025 SN - 978-3-031-96105-2 DO - https://doi.org/10.1007/978-3-031-96106-9_53 VL - 675 SP - 506 EP - 515 PB - Springer CY - Cham AN - OPUS4-64267 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liao, Chun-Man A1 - Bernauer, F. A1 - Niederleithinger, Ernst A1 - Igel, H. A1 - Hadziioannou, C. T1 - Assessment of prestress loss in a large-scale concrete bridge model under outdoor condition N2 - Environmental conditions affect the accuracy of field measurements used to monitor civil structures. Previous studies have shown that measured dynamic responses often lack the sensitivity needed for effective localized damage detection. To address this issue, our study focuses on distinguishing environmental effects from damage related effects in measured data to enhance vibration-based damage identification methods. Experimentally, the problem of prestress loss in a prestressed concrete bridge model was examined. By adjusting the pre-stressing force in a large-scale concrete bridge model, cracking phenomena were observed. To demonstrate field monitoring of a large-scale prestressed structure, noise recording was performed and the measurement data was analyzed with operational modal analysis. Additionally, ultrasonic testing, known for its high sensitivity in damage localization, was used to cross-check the structural damage. Seismic and coda wave interferometry were also employed to estimate wave velocities, providing insights into the level of prestress loss and temperature sensitivity. Ultimately, these measurable wave properties help to overcome the uncertainties associated with traditional vibration-based damage detection methods. T2 - EVACES 2025 CY - Porto, Portugal DA - 02.07.2025 KW - Prestress Loss KW - NDT KW - Ambient Vibration KW - Ultrasonic Testing KW - Coda Wave Interferometry KW - Seismic Interferometry PY - 2025 SN - 978-3-031-96105-2 DO - https://doi.org/10.1007/978-3-031-96106-9_20 VL - 675 SP - 181 EP - 189 PB - Springer Nature CY - Cham AN - OPUS4-64212 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröpfer, Dirk T1 - Comparative residual stress analysis on a DED-Arc manufactured high-strength steel component using the contour method and XRD N2 - Lightweight construction is a vital approach for reducing CO₂ emissions. It contributes to the development of more energy-efficient structures and supports the overall goal of achieving carbon neutrality in the transition to sustainable manufacturing. Thus, a topology-optimized design often leads to complex geometries. Additive manufacturing (AM) processes such as direct energy deposition with arc (DED-Arc) offers a great design freedom due to the build-up of components in layers. Furthermore, they enable efficient production due to the high deposition rate, process reliability and good automation capability. Further efficiency can be achieved through weight optimization, enabled by high-strength steels. However, a major challenge is the process induced residual stresses (RS) in the component. High tensile residual stresses are detrimental as they increase the risk of cold cracking. Knowledge of residual stress distribution is crucial for predicting service life of the component and structural integrity assessment, especially for safety critical applications. Therefore, this study focuses on the use of Contour method (CM) to analyse the full field longitudinal residual stresses in an open hollow cuboid component (dimensions: 120 x 50 x 30 mm3) manufactured by DED-Arc (yield strength > 730 MPa). In the contour method, the component is cut along a desired plane of interest and the contour of deformed cut surface is measured. A finite element model is used to reconstruct the residual stresses field in the 2-dimensional plane of cut. In this paper a modified cutting strategy was employed, post cutting the deformed cut surfaces were measured utilizing two surface measurement techniques i.e., coordinate measuring machine (CMM) and a 3D Scanner. The accuracy of the contour method was validated against surface stresses measured using X-ray diffraction. Additionally, a comparison of neutron diffraction experiments was conducted. The residual stresses were further correlated with hardness measurements. The results from surface measurement techniques showed good agreement regarding the measured displacement contours and the contour method results revealed peak stresses in the DED-Arc walls, bending deformation in substrate induces tensile stresses at the bottom of the substrate plate and compressive stresses in the middle top region. The residual stresses obtained from diffraction and contour method showed a good agreement and correlated qualitatively with the hardness measurements. T2 - 78th IIW Annual Assembly and International Conference on Welding and Joining CY - Genoa, Italy DA - 22.06.2025 KW - Residual stress KW - Contour method KW - DED-Arc/M KW - High-strength steel KW - Filler metals KW - XRD KW - Neutron diffraction PY - 2025 AN - OPUS4-65215 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Chloride binding by LDH/AFm phases and alkali-activated slag pastes N2 - Chloride binding by the hydrate phases of cementitious materials influences the rate of chloride ingress into these materials and, thus, the time at which chloride reaches the steel reinforcement in concrete structures. A particularly important role in this context is played by layered double hydroxides (LDHs), including AFm phases. Chloride binding isotherms of individual LDH/AFm phases would be required as input for computational models of chloride ingress, but such isotherms are only available for a few AFm phases, and in addition the available data are partly conflicting. The present study, conducted in the context of RILEM TC 283-CAM ‘Chloride transport in alkali-activated materials’, significantly extends the available database by determining the chloride binding isotherms of LDH/AFm phases (monosulfate, strätlingite, hydrotalcite, and meixnerite), and of alkali-activated slags (AAS) produced with four different activators (Na2SiO3, Na2O∙1.87SiO2, Na2CO3, and Na2SO4), in NaOH/NaCl solutions at various liquid/solid ratios. Selected solids after chloride binding were analysed by X-ray diffraction, and thermodynamic modelling was applied to simulate the phase changes occurring during chloride binding by the AFm phases. The chloride binding isotherms of LDH/AFm phases depended strongly on the liquid/solid ratio during the experiments, resolving apparent contradictions of the previously available data. The dependency on liquid/solid ratio must be attributed to kinetic restrictions, which are, however, currently poorly understood. Chloride binding by AAS pastes was generally higher than for Portland cement pastes and was only moderately influenced by the employed activator. A steep increase of the chloride binding by AAS occurred at free chloride concentrations above approx. 1.0 M, which is possibly related to chloride binding by the C-(N-)A-S-H gel in the AAS. T2 - RILEM Spring Convention 2024 & Conference on Advanced Construction Materials and Processes for a Carbon Neutral Society CY - Milan, Italy DA - 07.04.2024 KW - Chloride binding KW - Layered double hydroxides KW - AFm phases KW - Alkali-activated slags KW - Chloride sorption isotherms PY - 2024 AN - OPUS4-59855 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Thermo-mechanical and spalling behavior of normal weight and lightweight geopolymer concretes N2 - The mechanical and microstructural properties of two geopolymer concretes, produced with either quartz aggregate or expanded clay aggregate, were assessed before, during and after high-temperature exposure up to 750 °C in order to better understand the engineering properties of the material. SEM investigations were also undertaken to better understand the observed changes in the mechanical properties. It was found that dehydration of capillary water caused micro-cracking and strength losses at temperatures ≤ 300 °C. At higher temperatures (T ≥ 500 °C) sintering promoted strength increases, leading significant strength advantages over conventional concretes. Stress-mechanical strain curves, which are the basis of the fire design of concrete structures, were determined. In addition, the two geopolymer concretes where exposed to the ISO 834-1 standard fire curve in a small-scale spalling test set-up. Acoustic emission measurements during, and acoustic measurements and optical microscopy after heat exposure were employed to investigate crack formation during the tests. Both concretes did not spall, which is attributed to their comparatively high permeability and their low amount of chemically bound water. Significant crack formation was detected only around the temperature of the α–β quartz transition (573 °C) and on cooling. Because of aggregate deformations at the quartz transition temperature, deterioration after heating was more significant in the geopolymer concrete with quartz aggregates. Crack formation occurred also in the concrete with expanded clay aggregates, presumably caused by shrinkage of the geopolymer paste on cooling. T2 - Advances in Cement and Concrete Technology in Africa (ACCTA 2016) CY - Dar es Salaam, Tanzania DA - 27.01.2016 KW - Geopolymers KW - Concrete KW - Transient thermal creep KW - Spalling KW - Heat exposure PY - 2016 AN - OPUS4-36922 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - König, H. T1 - Practical tests with R290 used in reefer container refrigeration -leakage testing- N2 - The option of using flammable refrigerants in the reefer container has already been studied and reported by König (2013, 2014) in various publications. In the present paper, the results of experiments are presented, related to the investigation of the potential fire and explosions risks by R290 leaks in refrigerated containers. A safety concept for reefer containers operating with R290 as refrigerant has been tested and validated. In addition, there were extensive leakage simulations, the results have been evaluated for the comparison with the practical tests. Both experiments and the simulations were done at the Federal Institute for Materials Research and Testing (BAM). Further tests are carried out by the manufacturer with the support of the firefighting service and the Danish institute of Fire and Security Technology (DBI). The results from practical tests and the leakage simulations allow for first generalization and more precise studies with respect to potential risks of refrigerant leaks. Potentially explosive atmospheres situations can be evaluated much easier and appropriate measures can be derived. It turns out that dangerous situations for small, medium and rupture of pipe leaks are manageable. The results of the practical testing of leaking R290 inside and outside of a reefer container showed that the risk is being commonly overestimated. T2 - 12th IIR Gustav Lorentzen Conference on Natural Refrigerants CY - Glasgow, UK DA - 21.08.2016 KW - Reefer container KW - Safety concept KW - Leakage tests KW - Gas dispersion KW - Explosion tests PY - 2016 AN - OPUS4-38638 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Reinforcing steel in sulfide-containing concretes – corroding or not corroding? N2 - Blast furnace cements (CEM III) and alkali-activated slags are binders for concretes with several advantageous engineering properties, and their increased adoption in construction industry could contribute to reducing the CO2 emissions associated with cement production and use. However, the current knowledge about how these cements protect steel reinforcement in concretes against corrosion is very incomplete, which impedes their large-scale application. This knowledge gap is mainly due to the fact that these cements release sulfide and other reduced sulfur species into the concrete pore solution, the consequences of which for the state of the reinforcement and electrochemical measurements are not fully understood. The present contribution first describes peculiarities of electrochemical measurements of steel in sulfide-containing cementitious materials and related solutions as reported in the literature and a recent report by EFC Working Party 11. It is demonstrated that the high sulfide concentrations in these systems lead to low open circuit potentials and low polarisation resistances, which may be incorrectly interpreted as indicating active corrosion of the steel. Second, preliminary results of an ongoing project [funded by the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) – 458297195] related to the passivation and corrosion initiation of steel in sulfide-containing solutions and mortars are presented. Eight mortars based on one alkali-activated blast furnace slag (BFS), three alkali-activated BFS/fly ash blends, one sodium sulfate-activated CEM III/C (‘hybrid cement’), one CEM III/C, one CEM III/B, and one CEM I (ordinary Portland cement, OPC) were produced, and their pore solutions expressed and analysed after 7, 14, 28, and 56 days of curing. The pH values of the solutions differed systematically, with the highest pH values recorded for the CEM I and the alkali-activated BFS/fly ash blends with a high proportion of fly ash, and the lowest pH recorded for the CEM III/B. The redox potentials of the solutions were between −500 mV and −340 mV vs. Ag/AgCl for the alkali-activated binders, approx. +10 mV vs. Ag/AgCl for the CEM I, and in between for the CEM III/B and the CEM III/C. As expected, the electrical conductivity was highest for the alkali-activated binders. These results are explained by the chemical compositions of the pore solutions of the mortars. Finally, a test set-up to investigate the behaviour of steel in sulfide-containing solutions and the changes on subsequent oxygen and/or chloride addition is introduced. Preliminary electrochemical measurements of steel in sulfide-containing solutions are presented and discussed in the context of the above-mentioned data from the literature and the compositions of the pore solutions of the studied mortars. T2 - 7th Swiss Corrosion Science Day 2023 CY - Zurich, Switzerland DA - 24.04.2023 KW - Reinforcing steel KW - Sulfide KW - Concrete KW - Ground granulated blast furnace slag KW - Corrosion PY - 2023 AN - OPUS4-57386 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR ED - Rossignol, S. ED - Gluth, Gregor T1 - Special issue: Alkali-activated materials and geopolymers in ceramics and beyond N2 - Geopolymers and alkali-activated materials have emerged as a complement, and partly as an alternative, to traditional materials in various applications, such as traditional ceramics, energy saving, waste management, building construction, and filtration. These new materials can play an important role in mitigating climate change and promoting a circular economy, which is one of the reasons why they are being actively researched in many laboratories around the world. Open Ceramics, the official, peer-reviewed, Open Access journal of the European Ceramic Society, is dedicated to foster this research and is compiling a Special Issue with the title “Alkali-activated and geopolymer materials in ceramics and various applications”. The aim of this Special Issue is to promote new applications, the use of previously underused raw materials, and in particular a better understanding of the chemical and mechanical behavior of these materials. The scope of the Special Issue includes, but is not limited to, research on the following topics: - valorization of previously underused raw materials - a better understanding of established raw materials - detailed spectroscopic characterization of alkali-activated materials and geopolymers to elucidate their phase assemblage - the mechanism of formation of the phase(s) that comprise these binders - control of their mechanical properties - the effect of fillers/aggregates on their mechanical properties - their durability under various conditions and the underlying deterioration mechanisms - special applications and recycling-related considerations. KW - Alkali-activated materials KW - Geopolymers PY - 2021 UR - https://www.sciencedirect.com/journal/open-ceramics/special-issue/10789KQV7BR SN - 2666-5395 SP - 100013-1 EP - 100184-12 PB - Elsevier CY - Amsterdam AN - OPUS4-51984 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - One-part geopolymers and geopolymer-zeolite composites based on silica: factors influencing microstructure and engineering properties N2 - Mixing and curing of geopolymers and related alkali-activated materials without storage and handling of highly alkaline solutions possesses advantages regarding safety and economic viability; one possible approach is to produce these materials from solid silica feedstocks and solid sodium aluminate, and subsequent mixing with water. We present a comparison between geopolymers and geopolymer-zeolite composites synthesized by this route from different silica feedstocks (by-product silica from chlorosilane production, microsilica, rice husk ash) and with different SiO2/Al2O3 ratios, using results from XRD, NMR, SEM, thermal analysis, mechanical and acid resistance testing. The use of rice husk ash favors formation of a fully amorphous geopolymer with high strength. Utilization of the other silica feedstocks leads to formation of geopolymer-zeolite composites, the amount and kind of zeolites depending on the feedstock and the SiO2/Al2O3 ratio. These composites show beneficial dehydration behavior, viz. no distinct dehydration step of thermal strain, with the phase assemblage after heating to 1000 °C controlled by the starting composition. Mortars produced from both, the geopolymers as well as the compo¬sites, exhibit high resistance to sulfuric acid attack, making them promising materials for the construction and the repair of industrial and sewer structures. T2 - 42nd International Conference and Expo on Advanced Ceramics and Composites CY - Daytona Beach, FL, USA DA - 21.01.2018 KW - Alkali-activated materials KW - Geopolymers KW - Acid resistance KW - High-temperature resistance PY - 2018 AN - OPUS4-44145 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Structure, acid resistance and high-temperature behavior of silica-based one-part AAMs N2 - One-part geopolymers (OPGs) are a sort of alkali-activated materials (AAMs) which production avoids the use of highly-alkaline activator-solutions and contributes to a better acceptance of alternative mineral binders in terms of safety-related and economic aspects. In the present contribution OPGs were synthesized by blending silica sources (two industrial silicas and two biogenic silicas) with sodium aluminate and only water must be added to initiate the hardening, i.e. mixing is performed in the same way as for conventional Portland cements. The OPGs were characterized by XRD, and SEM and the degrees of reaction of the silicas were determined by a chemical dissolution method. The industrial silicas led to the formation of geopolymer-zeolite composites, that contained, besides geopolymeric gel, crystalline tectosilicates (e.g. zeolite A and hydrosodalite) and depending on the starting composition also unreacted silica. The biogenic silicas provided a higher reactivity and avoided the formation of crystallite by-products. The differences in the microstructures caused differences in the mechanical strength of the specimens. The treatment of the OPG composites at moderate elevated temperatures revealed promising behavior on thermal dehydration in terms of shrinkage and residual strength up to 700 °C. Above 700 °C sintering and partial melting occurred, and new phase formation commenced. After exposure to 1000 °C the specimens appeared virtually amorphous or formed stuffed silica structures of nepheline- or carnegieite-type type. The investigations of the OPG based mortars on their resistance against sulfuric acid in accordance with DIN 19573 (Appendix A) revealed very high residual strengths up to 78 % after treatment with H2SO4 (pH 1) for 70d. A mechanism of dissolution of the primary aluminosilicate reaction products of the pastes and the precipitation of a silica gel that protects the remaining aluminosilicates and decelerates further corrosion was found to be the main reason for the good performance under acidic conditions. The addition of CaO-containing feedstocks enhanced hardening, but at a certain content the resistance against sulfuric acid decreased, due to the formation of gypsum on exposure to sulfate. In addition, the mortars exhibited excellent shrinkage behavior as well as good bond to concrete substrates with pull-off strength up to > 3 MPa. The workability of the fresh mortars provided very good manual applicability; automatic applications such as sprayed and spun mortars will require further optimization regarding rheological properties. In summary, the studied OPG are promising materials for the construction and the repair of concrete structures, such as sewers, that are affected by biogenic sulfuric acid corrosion. T2 - Alkali Activated Materials and Geopolymers CY - Tomar, Portugal DA - 27.05.2018 KW - Alkali-activated materials KW - Geopolymers KW - Acid resistance KW - Solid state NMR PY - 2018 AN - OPUS4-45087 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sittner, Jonathan T1 - Calcined clays: Innovative production of cost-effective and sustainable supplementary cementitious materials N2 - Calcined clays are promising sustainable alternative materials for cement production. By calcining natural clay minerals (usually 600–900 °C), they become reactive and can be used as a partial replacement for Portland clinker in cement production. This results in a lower carbon footprint and reduced energy consumption in the production process. Replacing cement clinker with so-called supplementary cementitious materials (SCM) such as fly ash and blast furnace slag has been done for several decades. Calcined clays have also been used, mostly in the form of metakaolin, which significantly improves the strength and durability of mortar and concrete. However, its limited availability and high cost restrict its practical application to a few specialist applications. In comparison, 2:1 clay minerals such as illite or smectites are more widely available and economically attractive due to their lower costs. Recent research has explored the use of calcined 2:1 clay minerals as SCM, but their properties and efficient production are still not fully understood. In the present work, different clays from Germany are characterized and tested as potential calcined clay. Besides conventional calcination using a rotary kiln, fluidized bed calcination is used to improve the reactivity of the calcined clays while being less time-consuming and therefore more energy efficient. T2 - GeoSaxonia 2024 CY - Dresden, Germany DA - 23.09.2024 KW - Calcined clay KW - Supplementary cementitious material (SCM) PY - 2024 AN - OPUS4-61973 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gluth, Gregor A1 - Rickard, W.D.A. A1 - Werner, Steve A1 - Pirskawetz, Stephan T1 - Acoustic emission and microstructural changes in fly ash geopolymer concretes exposed to simulated fire N2 - Two fly ash-based geopolymer concretes with quartz aggregates or with expanded clay (lightweight) aggregates were exposed to the ISO 834-1 standard fire curve in a small-scale fire test set-up. Acoustic emission measurements during fire exposure and subsequent cooling were employed to study spalling events and cracking during the tests. Optical microscopy and additional acoustic measurements were conducted after the testing to better understand the crack propagation in the samples. The testing revealed that neither of the concretes were susceptible to spalling, which is particularly notable for the concrete with quartz aggregates, as it is a high-strength concrete. This behavior is attributed to the relatively high permeability of the concretes and their low amount of chemically bound water. Significant crack formation was detected only around the temperature of the alpha–beta quartz transition (573 °C) and on cooling. Because of aggregate deformations at the quartz transition temperature, deterioration after heating was more significant in the geopolymer concrete with quartz aggregates. Crack formation also occurred in the concrete with expanded clay aggregates, caused by shrinkage of the geopolymer paste on cooling. Acoustic emission measurements proved to be a valuable tool to investigate processes during high temperature exposure. KW - Geopolymers KW - Spalling KW - Concrete KW - Acoustic emission KW - Heat exposure PY - 2016 DO - https://doi.org/10.1617/s11527-016-0857-x SN - 1359-5997 SN - 1871-6873 VL - 49 IS - 12 SP - 5243 EP - 5254 PB - Springer AN - OPUS4-36907 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Corrosion of steel reinforcement in geopolymer mortars - leaching and carbonation processes investigated by galvanostatic pulse and potential measurements N2 - Potential to be used as binders for concrete with beneficial engineering properties and reduced manufacturing CO2 emissions. Knowledge of the durability of steel in these concretes and related properties of alkali-activated materials is a prerequisite for their application as building materials, if they are to be used for steel reinforced elements. However, to date only limited data exists on this topic. The present contribution focuses on durability-related transport properties of geopolymer-based mortars (as model systems for concrete). We report results of a polarization resistance data and corrosion potential vs. time curves for carbon steel bars embedded in a fly ash-based geopolymer mortar and a CEM I-based mortar (as reference) leached continuously over a period of 365 days. T2 - Eurocorr 2018 CY - Cracow, Poland DA - 09.09.2018 KW - Corrosion KW - Geopolymere KW - Betonstahl PY - 2018 AN - OPUS4-45948 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Klippel, A. A1 - Hofmann-Böllinghaus, Anja A1 - Gnutzmann, Tanja A1 - Piechnik, K. T1 - Reaction-to-fire testing of bus interior materials: Assessing burning behaviour and smoke gas toxicity N2 - Although fire safety regulations for buses have been adapted in recent years regarding, for example, fire detection and engine fire suppression systems, the changes in regulations for bus interior materials are minimal. A comparison of fire safety regulations for interior materials in other transport sectors for trains, ships or aircraft reveals a much lower level of requirements for bus materials. Although repeated bus accidents as well as fire statistics show the danger a bus fire can pose to passengers. In particular, the combination of a fire incident and passengers with reduced mobility led to severe disasters in Germany and other European countries. To enhance the fire safety for passengers, the interior bus materials are crucial as the fire development in the bus cabin determines whether escape and rescue is possible. Against this background, bus interior materials were tested in different fire test scenarios. Measurement of a wide variety of parameters, for example, the mass loss, ignition time, smoke gas composition, heat release rate among others were carried out. Tested materials complied to the newest set of requirements. For this purpose, interior materials and their components had to be identified according to their chemical structure. Parts of the tests were funded by BASt (Federal Highway Research Institute) in the project 82.0723/2018. Experimental results show reaction-to-fire behaviour which lead to very limited times for escape and rescue in case of fire in a bus cabin. Based on the studies on fire behaviour and toxicity assessment, recommendations for improved fire safety regulations for interior materials could be made. KW - Burning behaviour KW - Bus interior materials KW - Cone calorimeter KW - DIN tube furnace KW - FTIR spectroscopy KW - Reference values KW - Smoke toxicity PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-576085 DO - https://doi.org/10.1002/fam.3108 SN - 1099-1018 VL - 47 IS - 5 SP - 665 EP - 680 PB - Wiley CY - New York, NY AN - OPUS4-57608 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Anderson, Johan A1 - Chiva, Roman A1 - Dumont, Fabien A1 - Lalu, Octavian A1 - Hofmann-Böllinghaus, Anja T1 - Assessment of fire performance of facades in a round robin using the European approach N2 - In recent years, an experimental round robin of full-scale façade tests was conducted using the proposed new European approach for assessing the fire performance of façades. The initial results were used to develop a calibration scheme and to propose assessment criteria aligned with appropriate safety levels. During the project, a need emerged to evaluate the stability of the fire source and the Consistency of heat exposure. This paper addresses these concerns by comparing the mass loss rates across a series of tests and analysing averaged temperature readings at various locations on the façade. The findings indicate that the method demonstrates high stability in terms of mass loss rates and provides consistent and appropriate heat exposure. T2 - Interflam 2025, 16th International Fire Science and Engineering Conference CY - London, UK DA - 30.06.2025 KW - Facade systems KW - Testing PY - 2025 VL - 2025 SP - 562 EP - 572 PB - Interscience CY - London AN - OPUS4-63998 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Löhnert, Andrea A1 - Monreal, Nils A1 - Knaust, Christian A1 - Hofmann-Böllinghaus, Anja A1 - Krause, U. T1 - CFD modeling approach of smoke toxicity and opacity for flaming and non-flaming combustion processes N2 - Current engineer’s methods of fire safety design include various approaches to calculate the fire Propagation and smoke spread in buildings by means of computational fluid dynamics (CFD). Because of the increased computational capacity, CFD is commonly used for prediction of time-dependent safety parameters such as critical temperature, smoke layer height, rescue times, distributions of chemical products, and smoke toxicity and visibility. The analysis of smoke components with CFD is particularly complex, because the composition of the fire gases and also the smoke quantities depends on material properties and also on ambient and burning conditions. Oxygen concentrations and the temperature distribution in the compartment affect smoke production and smoke gas toxicity qualitatively and quantitatively. For safety designs, it can be necessary to take these influences into account. Current smoke models in CFD often use a constant smoke yield that does not vary with different fire conditions. If smoke gas toxicity is considered, a simple approach with the focus on carbon monoxide is often used. On the basis of a large set of experimental data, a numerical smoke model has been developed. The developed numerical smoke model includes optical properties, production, and toxic potential of smoke under different conditions. For the setup of the numerical model, experimental data were used for calculation of chemical components and evaluation of smoke toxicity under different combustion conditions. Therefore, averaged reaction equations were developed from experimental measurements and implemented in ANSYS CFX 14.0. KW - Fire modeling KW - Fire safety KW - Computational fluid dynamics (CFD) KW - Smoke toxicity PY - 2016 DO - https://doi.org/10.1002/fam.2340 SN - 1099-1018 VL - 40 IS - 6 SP - 759 EP - 772 PB - Wiley CY - West Sussex, UK AN - OPUS4-37514 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krüger, Simone A1 - Hofmann-Böllinghaus, Anja A1 - Berger, Anka A1 - Gude, Nicolas T1 - Investigation of smoke gases and temperatures during car fire – large-scale and small-scale tests and numerical investigations N2 - The hazards for passengers during vehicle fires result from the increasing temperature and the emitted smoke gases. A fire was set on a car to investigate the development of temperature and of gaseous fire products in the passenger compartment. The study was based on a full-scale test with a reconstructed scene of a serious car fire. The aim of this work was to identify the conditions for self-rescuing of passengers during a car fire. A dummy, equipped with several thermocouples, was placed on the driver’s seat. Also, the smoke gases were continuously collected through a removable probe sensor corresponding to the nose of the dummy in the passenger compartment and analyzed using Fourier transform infrared spectroscopy. Additionally, several car components were investigated in the smoke density chamber (smoke emission and smoke gas composition). It was found that the toxic gases already reached hazardous levels by 5 min, while the temperatures at the dummy were at that time less than 80 °C. The toxicity of smoke gases was assessed using the fractional effective dose concept. The various experimentally parameters (temperature and smoke gas composition) were implemented into numerical simulations with fire dynamics simulator. Both the experimental data and the numerical simulations are presented and discussed. KW - Smoke gases KW - FTIR spectroscopy KW - Car fire KW - Temperatures KW - FED KW - Numerical simulations PY - 2016 DO - https://doi.org/10.1002/fam.2342 SN - 1099-1018 VL - 40 IS - 6 SP - 785 EP - 799 PB - Wiley CY - Sussex, UK AN - OPUS4-37518 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Anderson, J. A1 - Boström, L. A1 - Chiva, R. A1 - Guillaume, E. A1 - Colwell, S. A1 - Hofmann-Böllinghaus, Anja A1 - Toth, P. T1 - European approach to assess the fire performance of façades N2 - Several attempts have been made in the past to develop a European harmonized testing and assessment method for façades before the European commission decided to publish a call for tender on the topic. A project consortium from five countries (Sweden, UK, France, Germany and Hungary) applied to the call for tender and was contracted to develop a European approach to assess the fire performance of façades. 24 sub-contractors and 14 stakeholder entities were part of the project. The objective of the European project was to address a request from the Standing Committee of Construction (SCC) to provide EC Member States regulators with a means to regulate the fire performance of façade systems based on a European Approach agreed by SCC. The initial stages of this Project were focused on establishing a Register of the regulatory requirements in all Member States in relation to the fire Performance of façade systems, and to identify those Member States who have regulatory requirements for the fire performance façade systems which go beyond the current EN 13501 (reaction to fire and fire resistance) classification systems and to collate the details of these additional requirements. After having confirmed the regulatory needs a testing and classification methodology based on BS 8414 and DIN 4102-20 was developed to address the identified key performance and classification characteristics. This paper is a short overview of results the two-year development work, which Final Report published by the European Commission in 2018. KW - Facade KW - Regulation KW - Testing PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-530501 DO - https://doi.org/10.1002/fam.2878 SN - 1099-1018 VL - 45(5) IS - Special issue: Facade fire safety SP - 598 EP - 608 PB - Wiley CY - Oxford AN - OPUS4-53050 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hofmann-Böllinghaus, Anja A1 - Klippel, Andrea T1 - Vehicle Fires: Significant Fire Hazard in Transportation Infrastructure N2 - Vehicle fires in transportation infrastructure such as depots, car parks, tunnels and stations are a recurring phenomenon, with recent years witnessing an alarming number of severe incidents, particularly in vehicle depots. These fires often result in the total loss of both vehicles and buildings, with striking similarities in their progression. Analysis of recent fire events, including a study conducted for the German insurer Provinzial, shows that fires in bus depots, military facilities and car parks tend to spread rapidly and destructively. While building regulations vary across sectors and countries, the fire safety standards for interior materials in road vehicles remain globally harmonized and are based on outdated regulations such as FMVSS 302, which offer only a minimal level of protection. In contrast, materials used in trains, ships, and aircrafts must comply with significantly stricter fire safety standards, which may explain the relatively lower incidence of fires in these sectors. Common fire protection systems in depots, such as sprinklers and vents, often fail to account for the specific characteristics of automotive vehicles, including their watertight design and the rapid development of hot gas layers that accelerate fire spread. Insurance companies have begun to acknowledge these challenges. Given the high flammability, heat release and smoke toxicity of materials commonly used in vehicles, combined with the growing share of combustible plastics over the past decades, this paper argues for a paradigm shift. Instead of relying solely on inhancing building protection, introducing significantly stricter fire safety requirements for vehicle materials could offer a more effective and sustainable approach to safeguarding transportation infrastructure. Ongoing experimental investigations are being conducted to evaluate the reaction to fire behavior of various bus interior materials. These studies focus on the emission of toxic gases during combustion, with particular attention to substances exceeding critical AEGL thresholds. Materials such as polyurethane foams and hard plastics have shown significant variation in their smoke gas profiles, highlighting potential health and safety risks in fire scenarios. The research aims to support the development of safer material choices and regulatory measures. Upon completion of tests with additional materials, all findings will be published to ensure transparent and comprehensive reporting. T2 - Interflam 2025, 16th International Fire Science and Engineering Conference CY - London, United Kingdom DA - 30.06.2025 KW - Vehicle fires KW - Transportation PY - 2025 AN - OPUS4-63922 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Geoerg, Paul A1 - Schumann, Jette A1 - Holl, Stefan A1 - Holl, Maik A1 - Hofmann-Böllinghaus, Anja T1 - The influence of individual impairments in crowd dynamics N2 - The importance of empirical relations to quantify the movement of pedestrians through a facility has increased during the last decades since performance-based design methods became more common. Bottlenecks are of special interest because of their importance for egress routes and as they result in a reduced capacity. The empirical relations as the density-dependent movement speed or flow rate were derived by studies under laboratory conditions, which were usually conducted with populations of homogeneous characteristics forbetter control of influencing variables. If individual characteristics of a crowd become more heterogeneous, individuals were forced to adapt their individual movement and control individual manoeuvring. These unintended interactions lead to a different shape of the fundamental empirical relations. Here, we present results from a movement study under well-controlled boundary conditions in which participants with and without different characteristics of disabilities participated. To consider the effect of different heterogeneities on the capacity of a facility, fundamental diagrams are generated using the Voronoi method. If participants with visible disabilities (such as using assistive devices) are part of a crowd, significant differences relating to the shape of the empirical Relations and the capacities are found. This indicates that the heterogeneity of a Population leads to an increased interpersonal interaction which results in influenced movement characteristics. KW - Engineering egress data KW - Heterogeneity KW - Human behaviour KW - Movement characteristics KW - Pedestrian dynamics PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-508943 DO - https://doi.org/10.1002/fam.2789 SN - 0308-0501 VL - 45 IS - 4 SP - 529 EP - 542 PB - Wiley Online Libary CY - New Jersey, USA AN - OPUS4-50894 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Piechnik, Kira A1 - Hofmann-Böllinghaus, Anja A1 - Klippel, Andrea T1 - Self‐ignition of forest soil samples demonstrated through hot storage tests N2 - AbstractThe increasing threat of forest fires on a global scale is not only a matter of concern due to the potential harm they may cause to both human and animal life but also due to their significant role in exacerbating climate change. In light of these circumstances, one might inquire as to whether forest soil can self‐ignite and, if so, under what conditions and at what temperatures this phenomenon may occur. This question is being addressed in the German pilot “Fire science of wildfires and safety measures” of the EU project TREEADS, and the first results are presented below. The importance of basic research into the self‐ignition of forest soil cannot be underestimated, as it provides crucial knowledge to prevent forest fires and protect human and animal health. Furthermore, mitigating the occurrence of forest fires can also play a role in reducing greenhouse gas emissions, contributing to global efforts to combat climate change. The procedure of the hot storage test is an effective means of determining whether a material can self‐ignite. During the investigation of six soil samples, it was found that five of them were indeed capable of self‐ignition. In addition to determining whether the material ignites, the modified hot storage test also analyzed the resulting smoke gases and measured their concentration. The research question of whether regional forest soil is capable of self‐ignition can be answered with yes based on these initial tests. Further experiments are needed to determine if self‐ignition causes forest fires. KW - FTIR KW - Hot storage KW - Ignition KW - Soil KW - Wildfire PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-594617 DO - https://doi.org/10.1002/fam.3198 SN - 1099-1018 VL - 48 IS - 4 SP - 495 EP - 507 PB - Wiley CY - New York, NY AN - OPUS4-59461 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nandish, Ranjith A1 - Knaust, Christian A1 - Hofmann-Böllinghaus, Anja A1 - Gnutzmann, Tanja A1 - Zehfuß, Jochen T1 - Simulation of wood pyrolysis with component-based mechanism N2 - This paper presents a comprehensive fire simulation study that models the pyrolysis process of beech wood using kinetic parameters with the Fire Dynamics Simulator (FDS). The kinetic methodology is based on the application of these kinetic parameters to govern the underlying pyrolysis reactions. The primary objective was to numerically model the pyrolysis process for beech wood using both single-component (single-step, single reaction scheme) and multi-component (single-step, multi-reaction scheme) kinetic reaction schemes. The accuracy of the numerical model was validated by comparing FDS simulation results with experimental data obtained from thermogravimetric analysis (TGA) and cone calorimeter tests. This approach aids in identifying reliable kinetic reaction input parameters for modelling wood fires. A case study was included to demonstrate the implementation of the kinetic reaction schemes. Numerical results from the TGA simulations for the small-scale pure cellulose test using the single-component approach exhibit consistency with the experimental data. Furthermore, the results demonstrated that the multi-component approach more accurately replicates the shape of the experimental curve for beech wood compared to the single-component approach. However, discrepancies in the tail regions of the curves obtained from the FDS simulations showed the need for further improvement in the modelling approach, particularly regarding the exclusion of char oxidation reactions, which needs to be investigated further. KW - Simulation KW - Wood PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639272 DO - https://doi.org/10.1007/s00231-025-03571-7 SN - 0947-7411 VL - 61 IS - 6 SP - 1 EP - 14 PB - Springer Science and Business Media LLC AN - OPUS4-63927 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hofmann-Böllinghaus, Anja A1 - Klippel, Andrea A1 - Gnutzmann, Tanja A1 - Kaudelka, Sven A1 - Rabe, Frederik T1 - Influence of modern plastic furniture on the fire development in fires in homes: large-scale fire tests in living rooms N2 - About 80% of all fire fatalities in Germany occur because of fires in homes. It has been known for some time that modern materials (synonym for materials consisting mostly of synthetic polymers) tend to burn differently from older materials (synonym for materials consisting mostly of fibrous cellulosic substances) and it has been acknowledged that the amount of combustible plastics in homes has increased significantly over the last decades. To investigate the influence of modern furniture and ventilation conditions of fires in homes, a series of four large-scale tests in two Living rooms (LRs) with adjacent rooms (ARs) was performed by BAM and the Frankfurt fire service. Two LRs, one with older furniture and one with modern furniture, were tested twice each. Each test started with the ignition of a paper cushion on an upholstered chair. The influence of modern materials on the fire development was investigated, as well as the influence of the ventilation on the fire development. In all settings, an upholstered chair was the first burning item. Results of the test series show that fires in rooms with modern furniture develop faster than fires in rooms with older furniture. This is true for temperature development in the rooms as well as for smoke production. KW - Room fire KW - Furniture KW - Modern KW - Gas analysis KW - Smoke PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-527568 DO - https://doi.org/10.1002/fam.2934 VL - 45 IS - 1 SP - 155 EP - 166 PB - Wiley CY - London AN - OPUS4-52756 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Manes, M. A1 - Sauca, A. A1 - El Houssami, M. A1 - Andersson, P. A1 - McIntyre, C. A1 - Campbell, R. A1 - Rush, D. A1 - Hofmann-Böllinghaus, Anja A1 - Wagner, P. A1 - Leene, M. A1 - Oberhagemann, D. A1 - Jomaas, G. A1 - Grone, F. A1 - Guillaume, E. T1 - Closing Data Gaps and Paving the Way for Pan-European Fire Safety Efforts: Part II—Terminology of Fire Statistical Variables N2 - A well-defined terminology of fire-related variables is important for correct analyses and supporting knowledge-based decisions regarding the evaluation of building fires at the European level. After developing an overview of current practices for fire statistics in Part I, the terminology used and the data collected by the EU Member States and eight other countries regarding fire incidents, property damage and human losses were mapped to increase awareness of their practice and support a comprehensive assessment of several fire statistical datasets. A questionnaire was distributed to relevant authorities responsible for the collection, elaboration/analysis, and fire statistical data publications to define and select the essential variables for an appropriate fire assessment and fire incident description. Based on the results of the questionnaire able to identify the essential fire statistical variables and a detailed analysis of current definitions adopted in the fire statistics of the EU Member States and other countries, a common terminology is proposed to collect the necessary data in the EU Member States and obtain meaningful datasets based on standardised terms and definitions. The results will generate essential outputs to move towards harmonised fire statistics at the EU level and contribute to an appropriate analysis able to improve fire prevention and fire mitigation in building fires. KW - Fire statistics PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-575725 DO - https://doi.org/10.1007/s10694-023-01408-5 SN - 1572-8099 SP - 1 EP - 32 PB - Springer CY - Heidelberg AN - OPUS4-57572 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mezhov, Alexander A1 - Kulisch, D. A1 - Goncharov, A. A1 - Zhutovsky, S. T1 - A Comparative Study of Factors Influencing Hydration Stoppage of Hardened Cement Paste N2 - There is no consensus on which hydration stoppage method is optimal to preserve the microstructure and mineral composition of samples, especially considering the specific aspects of different testing methods, such as TGA, MIP, or XRD. This paper presents a quantitative comparison between the most popular hydration stoppage strategies and parameters such as the sample piece size, the soaking time in a solvent, and the type, as examined on cement paste hydrated for 7 days. It was found that the carbonation appears either for samples smaller than 2.36 mm and bigger than 4.75 mm or samples soaked in a solvent for longer than 1 h. Fast solvent replacement leads to ettringite diminution and total pore volume increase. Among others, solvent replacement with subsequent gentle heating under a vacuum was found to be the most efficient, whereas it was experimentally demonstrated that isopropyl alcohol stops hydration faster than ethanol and acetone. KW - Hydration stoppage KW - Solvent replacement KW - Soaking time KW - Sample piece size PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-582430 DO - https://doi.org/10.3390/su15021080 VL - 15 IS - 2 SP - 1 EP - 21 PB - MDPI CY - Basel, Switzerland. AN - OPUS4-58243 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Schönsee, Eric A1 - Jeyifous, Olubunmi Anthony A1 - Mezhov, Alexander A1 - Hüsken, Götz T1 - Introduction of a monitoring system for Bingham fluids in additive manufacturing with concrete N2 - Freeform additive manufacturing of concrete structures is a rising technology in civil engineering with several fascinating advantages. Nonetheless, to ensure reliability and structural integrity, standards and quality control are required in the future to bring this technology into the market. As the concrete is manufactured continuously, continuous quality control of the printing process is also required, i.e. comprehensive process monitoring. At BAM, a test rig will be installed, enabling the printing of concrete structures with a maximum size of 2 m x 1 m x 1 m (l x w x h). Here, process monitoring is the focus of the test rig. In this study, we show the results of the first pump tests, including the measurement of several parameters such as temperature and pressure along the supply system, i.e. from the concrete pump to the printer head. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Additive manufacturing of concrete KW - Process monitoring KW - Non-destructive testing KW - Bingham fluid PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-556367 SP - 1 EP - 12 AN - OPUS4-55636 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unger, Jörg F. T1 - From scientific models to reliable decision making – RDM as a backbone for validated, FAIR, and reproducible engineering simulations N2 - Engineering simulations play a central role in predicting system behavior and supporting design decisions. Their impact will increase due to the concepts of virtual lab, digital twins and predictive maintenance, where expensive prototyping is reduced with simulations or where real measurement data of the structures or parts are used in combination with simulation models to improve decision making. The credibility of a simulation model depends on the trust it earns within the scientific and engineering community. This trust can only be established through rigorous verification and validation. Verification and validation are inherently hierarchical processes. At the highest level, global approaches—such as standardized benchmarks and shared validation datasets—provide a common foundation for assessing model correctness and applicability across domains. These global resources enable regulatory bodies, industry, and research communities to evaluate whether models and their implementations meet agreed-upon standards. Research Data Management (RDM) provides the infrastructure to support these processes by enabling formalized model definitions, structured validation datasets, and transparent verification procedures and complete provenance descriptions of the underlying workflows. Currently, many engineering models are published as descriptive text or embedded in specific software implementations, which hinders reproducibility and standardization. Numerical results presented in publications must be fully reproducible. For regulatory assessment and interoperability, models require software-agnostic, machine-readable definitions that include all information needed for implementation and execution, such as scope, assumptions, parameter identification procedures, and uncertainty bounds. Formal definitions alone do not guarantee consistency. Verification benchmarks are essential to confirm that different implementations of the same mathematical or numerical model produce equivalent results. Likewise, validation requires structured experimental data that is publicly available and documented according to community-agreed protocols for tests, measurements, and metadata. Robust calibration and uncertainty quantification frameworks must provide systematic, reproducible procedures for parameter estimation and uncertainty propagation, while the complete provenance of these steps has to be documented. Validation should extend beyond controlled laboratory conditions to diverse real-world scenarios. The presentation will explore practical strategies for achieving reproducibility and reusability in engineering simulations through structured workflows, provenance tracking, and standardized data management practices. It will address the integration of experimental data for validation, the role of verification benchmarks, uncertainty quantification frameworks, and tool-independent model descriptions—including VMAP for result exchange—within collaborative platforms that support joint projects and regulatory compliance. T2 - GAMM Activity Group on Research Software Engineering and Research Data Management in Mathematics & Mechanics (GAMM FA RSE&RDM) CY - Braunschweig, Germany DA - 04.12.2025 KW - Experimental data KW - Verification and validation KW - UQ KW - Reproducibility (workflows) KW - Reusability (provenance tracking of simulation results) PY - 2025 AN - OPUS4-65267 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unger, Jörg F. T1 - Methodological prerequisites for reliable simulation results in the Virtual Lab and Digital Twins N2 - Mit dem zunehmenden Einsatz von Methoden wie Künstlicher Intelligenz, Digitalen Zwillingen und datengetriebener Modellierung erweitert sich das Anwendungsspektrum der virtuellen Produktentwicklung kontinuierlich. In sicherheitsrelevanten Anwendungsfeldern steigen dabei die Anforderungen an die Qualität, Nachvollziehbarkeit und externe Prüfbarkeit von Simulationsergebnissen – insbesondere im Hinblick auf Reproduzierbarkeit und Transparenz. Der Beitrag analysiert zentrale methodische und strukturelle Herausforderungen für den zuverlässigen Einsatz numerischer Simulationen in solchen Kontexten. Im Mittelpunkt stehen folgende Aspekte: • Die formale, softwareunabhängige Spezifikation mathematischer und numerischer Modelle, einschließlich einer standardisierten Beschreibung sowohl der Problemstellung als auch der Ergebnisgrößen. • Die Validierung sämtlicher Modellkomponenten anhand von Anwendungsszenarien mit hoher Ähnlichkeit zur realen Systemumgebung. • Die systematische Quantifizierung von Unsicherheiten, insbesondere im Hinblick auf Sim2Real-Modellabweichungen und deren Einfluss auf die Aussagekraft der Simulation. • Die Verifikation der Softwareimplementierung durch standardisierte Benchmark-Vergleiche. Hierzu wird ein Konzept föderierter Benchmarks mit dokumentierter Herkunft („Provenance“) vorgestellt, das eine transparente, reproduzierbare und öffentlich zugängliche Verifikation von Simulationswerkzeugen ermöglicht. Die Benchmarks folgen definierten Formaten, können dezentral veröffentlicht und in eine zentrale, abfragbare Datenbank integriert werden. Durch diese standardisierten Schnittstellen können dann Metriken zum Vergleich der Benchmarks visualisiert und in Analysen bereitgestellt werden. Der Beitrag zielt darauf ab, zentrale Herausforderungen und offene Fragestellungen bei der methodischen Absicherung simulationsbasierter Aussagen zu identifizieren und zur Diskussion zu stellen – insbesondere im Spannungsfeld zwischen Modellbildung, Validierung, Verifikation und Unsicherheitsquantifizierung. T2 - Symbiose von Simulation und Test CY - Wiesbaden, Germany DA - 12.11.2025 KW - Structured validation data KW - Model calibration KW - UQ PY - 2025 AN - OPUS4-65270 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Jafari, Abbas T1 - A python library for finite element (FE) modelling of static/quasi-static structural mechanics problems with legacy FEniCS N2 - This is a python library for finite element (FE) modelling of static/quasi-static structural mechanics problems with legacy FEniCS, which contains the following main modules. Module structure: for defining a structural mechanics experiment, including geometry, mesh, boundary conditions (BCs), and time-varying loadings. The time is quasi-static, i.e. no dynamic (inertia) effects will be accounted for in the problem module as follows. Module material: for handling constitutive laws such as elasticity, gradient damage, plasticity, etc. Module problem: for establishing structural mechanics problems for desired structures and material laws coming from the two above modules, and solving the problems built up. These can be performed for two main cases: static (no time-evolution) that also includes homogenization, and quasi-static (QS). KW - Finite element (FE) KW - Static/quasi-static structural mechanics KW - FEniCS PY - 2025 DO - https://doi.org/10.5281/zenodo.17805724 PB - Zenodo CY - Geneva AN - OPUS4-65269 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Jafari, Abbas A1 - Titscher, Thomas A1 - Robens-Radermacher, Annika T1 - Bayem: Implementation and derivation of “variational Bayesian inference for a nonlinear forward model [Chappell et al 2008]“ for arbitrary, user-defined model errors N2 - A python implementation of an analytical variational Bayes algorithm of "Variational Bayesian inference for a nonlinear forward model", Chappell, Michael A., Adrian R. Groves, Brandon Whitcher, and Mark W. Woolrich, IEEE Transactions on Signal Processing 57, no. 1 (2008): 223-236, with an updated free energy equation to correctly capture the log evidence. The algorithm requires a user-defined model error allowing an arbitrary combination of custom forward models and measured data. KW - Implementation KW - Variational Bayesian inference KW - Nonlinear forward model PY - 2025 DO - https://doi.org/10.5281/zenodo.17804665 PB - Zenodo CY - Geneva AN - OPUS4-65268 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Robens-Radermacher, Annika T1 - Modeling the influence of temperature for extrusion based 3d concrete printing from material to structural stability N2 - Abstract: 3D concrete printing (3DCP) aims to revolutionize construction by increasing automation, reducing material usage, and enabling customized designs. Despite its potential, the lack of regulations and reliance on trial-and-error methods result in significant waste and inefficiencies. Reliable models are needed to predict and control the complex printing process with its various influencing factors from material, process, and environment. This study aims to develop a structural model to predict print stability and prevent buckling and material failure in extrusion-based 3D concrete printing (3DCP), with a focus on environmental influences, particularly temperature. The structural build-up of the material is crucial for stability but is influenced by material ingredients, water-binder ratio, and ambient conditions, which vary in real-world projects. It describes the process of cementitious material gaining strength and stability during its early ages due to thixotropy and early hydration. Modeling that, a time- and temperature-dependent model for the evolution of early-age material parameters, such as stiffness, is derived. The model employs the maturity method, using an equivalent time to capture the temperature influence. It is verified using experimental data on stiffness evolution from squeeze flow tests and yield stress evolution measured from rotational rheometer tests. The model parameters are estimated using Bayesian inference, and validation shows good agreement with experimental data for both parameters at the material level. Subsequently, the derived time- and temperature-dependent stiffness model is adapted into a structural simulation using an elastoplastic material law with nonlinear hardening to study the temperature effect on the stability of 3DCP. Layers are activated sequentially based on a pseudo-density approach. The method is illustrated with an example of a printed wall with a width of one layer under varying ambient temperatures. The temperature impact on buckling and material failure during printing is demonstrated and numerically investigated through a sensitivity study. T2 - 95 th Annual Meeting of the International Association of Applied Mathematics and Mechanics (GAMM) CY - Poznan, Poland DA - 07.04.2025 KW - 3D concrete printing KW - Structural build-up KW - Temperature KW - Maturity method KW - Structural simulation PY - 2025 AN - OPUS4-62966 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Poli, Marco A1 - Grätz, Rainer A1 - Schröder, Volkmar T1 - An experimental study on safety-relevant parameters of turbulent gas explosion venting at elevated initial pressure N2 - The effects of a gas explosion in enclosures like vessels can be limited e.g. by gas explosion venting systems. The major design step of this constructive explosion protection method is to determine the required vent area, which depends significantly on whether turbulent combustion exists. However, current standards like NFPA 68 or EN 14994 are applicable only to limited boundary conditions and as far as possible only to laminar flame propagation. Difficulties arise in the assessment or predictability of gas explosion hazard when turbulence occurs. In this research especially venting at elevated initial pressure has been shown to accelerated flame propagations and therefore, to a considerably higher reduced pressure. Therefore, it is essential to provide a broader data base of turbulent combustion and explosion behavior to verify the existing rules or to determine their safety-relevant parameters. For a better safety assessment or design of protective systems the turbulent combustion and accelerated gas explosion behaviour of quiescent methane and hydrogen in air were investigated at initial pressures up to 8 bar using vessels up to 100 litres. In particular a systematic study was performed to investigate the influence of turbulence on the overpressure development during accelerated gas explosion. Moreover, the present study consider the position of the spark igniters, the burning velocity and the maximum pressure rise for different concentration of fuel as well as the size of orifice and/or vent area. A choice of experimental tests showed under the investigated conditions that not only turbulence inducing obstacles but also over sized vent areas could lead to an increased pressure development and therefore to an inacceptable safety state. T2 - 20th International Congress of Chemical and Process Engineering CHISA 2012 CY - Prague, Czech Republic DA - 25.08.2012 KW - Gas explosion venting KW - Turbulent combustion KW - Obstacles PY - 2012 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-264288 DO - https://doi.org/10.1016/j.proeng.2012.07.398 SN - 1877-7058 VL - 42 SP - 90 EP - 99 PB - Elsevier CY - Amsterdam AN - OPUS4-26428 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph T1 - Introduction of a monitoring system for Bingham fluids in additive manufacturing with concrete N2 - Freeform additive manufacturing of concrete structures is a rising technology in civil engineering with several fascinating advantages. Nonetheless, to ensure reliability and structural integrity, standards and quality control are required in the future to bring this technology into the market. As the concrete is manufactured continuously, continuous quality control of the printing process is also required, i.e. comprehensive process monitoring. At BAM, a test rig will be installed, enabling the printing of concrete structures with a maximum size of 2 m x 1 m x 1 m (l x w x h). Here, process monitoring is the focus of the test rig. In this study, we show the results of the first pump tests, including the measurement of several parameters such as temperature and pressure along the supply system, i.e. from the concrete pump to the printer head. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Additive manufacturing of concrete KW - Process monitoring KW - Non-destructive testing KW - Bingham fluid PY - 2022 AN - OPUS4-55637 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska T1 - Acoustic emission testing N2 - The phenomenon of acoustic emission (AE) and fundamentals of AE testing procedures are presented. AE based failure analysis of reinforced concrete beam under bending load, steel pipe segments under bending load and wood based materials under tension load are discussed. T2 - INFRASTAR, Training Week #03 at AAU CY - Aalborg, Denmark DA - 04.06.2018 KW - Acoustic emission PY - 2018 AN - OPUS4-45147 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska T1 - Non-threshold acoustic emission analysis of damage evolution in pipe segments of steel S355J2H under bending load N2 - Four-point bending tests were carried out to analyze the acoustic characteristics of damage development in pipe segments made of steel, grade S355J2H, being 2.5 m long with an outer diameter of 168 mm and 16 mm wall thickness. To induce stable crack growth, the pipe segments were pre-damaged by a 90°circumferential notch in the middle of the pipe length. While the pipe was quasi-statically loaded, microscopic damage and plastic deformation accumulated to form a macroscopic crack that grew through the pipe wall until leakage. For acoustic emission (AE) monitoring, four broadband sensors of type VS 900 M were mounted close to the notch. Continuous AE signal detection was performed by the non-threshold method. Advantages and disadvantages of the non-threshold AE monitoring compared to a commonly employed method analyzing only signals exceeding a predefined threshold are discussed. The results of AE analysis are compared to additional information on the crack growth detected by the direct current potential drop (DCPD) technique. These studies were carried out in the course of the interdisciplinary research project AGIFAMOR, Ageing infrastructures - distributed acoustic monitoring of pipes at BAM. T2 - 33rd European Conference on Acoustic Emission Testing CY - Senlis, France DA - 12.09.2018 KW - Crack growth KW - Crack initiation KW - Four-point bending test KW - Steel pipe KW - Acoustic emission PY - 2018 AN - OPUS4-45964 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska T1 - Feasibility study: Continuous monitoring of pipes using distributed acoustic and fibre optic sensors N2 - The feasibility study „AGIFAMOR. Ageing infrastructures – distributed acoustic monitoring of pipes” is an interdisciplinary research project at BAM internally financed from 2015 to 2018. Therefore, the quite young fibre optic sensing technology of distributed acoustic sensing (DAS) was investigated to possibly be extended towards a global condition monitoring system for pipelines operating in real time. DAS is a highly dynamic fibre optic sensing technology based on the method of coherent optical time domain reflectometry (C-OTDR). DAS allows capturing strain changes in the range of kHz. For the experimental work, the most suitable application yielding an optimum sensitivity was proven by wrapping a standard single-mode silica fibre around the pipe. The DAS sensitivity was investigated regarding the detection of 1) incidents that initiate propagation of acoustic waves in the pipe wall, 2) changes inside the pipeline causing altered flow and 3) damage development in the pipe wall. Therefore, several testing setups in laboratory as well as in real scale were realized. For comparison purposes, experiments were accompanied by acoustic emission analyses and by measurements with accelerometers. DAS was found to be very sensitive to gas ignition and its propagation across the pipe. Furthermore, the ability of DAS to detect and localize acoustic signals associated with pipeline leakage was demonstrated. The detection of crack formation and propagation within the pipe wall by means of DAS was studied during bending tests on several pipe segments, but was not proven so far with certainty. As expected, these studies turned out as the most difficult challenge due to the random occurrence and transient nature of microscopic damage phenomena. T2 - International Symposium on Structural Health Monitoring and Nondestructive Testing CY - Saarbrücken, Germany DA - 04.10.2018 KW - Fibre optic acoustic sensing KW - Continous monitoring KW - Acoustic emission KW - Accelerometers KW - Bending tests on pipe segments KW - Leak detection PY - 2018 AN - OPUS4-46200 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - INPR A1 - Andrés Arcones, Daniel A1 - Weiser, M. A1 - Koutsourelakis, P-S. A1 - Unger, Jörg F. T1 - Embedded Model Bias Quantification with Measurement Noise for Bayesian Model Calibration N2 - A key factor in ensuring the accuracy of computer simulations that model physical systems is the proper calibration of their parameters based on real-world observations or experimental data. Inevitably, uncertainties arise, and Bayesian methods provide a robust framework for quantifying and propagating these uncertainties to model predictions. Nevertheless, Bayesian methods paired with inexact models usually produce predictions unable to represent the observed datapoints. Additionally, the quantified uncertainties of these overconfident models cannot be propagated to other Quantities of Interest (QoIs) reliably. A promising solution involves embedding a model inadequacy term in the inference parameters, allowing the quantified model form uncertainty to influence non-observed QoIs. This paper introduces a more interpretable framework for embedding the model inadequacy compared to existing methods. To overcome the limitations of current approaches, we adapt the existing likelihood models to properly account for noise in the measurements and propose two new formulations designed to address their shortcomings. Moreover, we evaluate the performance of this inadequacy-embedding approach in the presence of discrepancies between measurements and model predictions, including noise and outliers. Particular attention is given to how the uncertainty associated with the model inadequacy term propagates to the QoIs, enabling a more comprehensive statistical analysis of prediction’s reliability. Finally, the proposed approach is applied to estimate the uncertainty in the predicted heat flux from a transient thermal simulation using temperature observations. KW - Model bias KW - Bayesian inference KW - Noise KW - Model updating KW - Quantity of Interest PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-652720 DO - https://doi.org/10.48550/arXiv.2410.12037 SP - 1 EP - 37 PB - arXiv.org AN - OPUS4-65272 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - INPR A1 - Villani, P. A1 - Andés-Arcones, Daniel A1 - Unger, Jörg F. A1 - Weiser, M. T1 - Posterior sampling with Adaptive Gaussian Processes in Bayesian parameter identification N2 - Posterior sampling by Monte Carlo methods provides a more comprehensive solution approach to inverse problems than computing point estimates such as the maximum posterior using optimization methods, at the expense of usually requiring many more evaluations of the forward model. Replacing computationally expensive forward models by fast surrogate models is an attractive option. However, computing the simulated training data for building a sufficiently accurate surrogate model can be computationally expensive in itself, leading to the design of computer experiments problem of finding evaluation points and accuracies such that the highest accuracy is obtained given a fixed computational budget. Here, we consider a fully adaptive greedy approach to this problem. Using Gaussian process regression as surrogate, samples are drawn from the available posterior approximation while designs are incrementally defined by solving a sequence of optimization problems for evaluation accuracy and positions. The selection of training designs is tailored towards representing the posterior to be sampled as good as possible, while the interleaved sampling steps discard old inaccurate samples in favor of new, more accurate ones. Numerical results show a significant reduction of the computational effort compared to just position-adaptive and static designs. KW - Adaptive Gaussian Processes KW - Bayesian parameter identification KW - AGP PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-652731 DO - https://doi.org/10.48550/arXiv.2411.17858 SP - 1 EP - 23 PB - arXiv.org AN - OPUS4-65273 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unger, Jörg F. T1 - Methodological Prerequisites for Reliable Simulation Results in the Virtual Lab and Digital Twins N2 - Simulationen übernehmen zunehmend eine zentrale Rolle in sicherheitskritischen Entscheidungsprozessen, etwa im Bauwesen, bei digitalen Zwillingen oder in der prädiktiven Instandhaltung. Damit diese Entscheidungen auf zuverlässigen numerischen Modellen basieren können, müssen die zugrunde liegenden Teilmodelle eindeutig beschrieben, reproduzierbar und in der Community validiert sein. Dieses Manuskript skizziert die notwendigen Voraussetzungen für vertrauenswürdige, FAIR-konforme und entscheidungsfähige Simulationsprozesse. Zunächst wird die Notwendigkeit einer formalen, softwareunabhängigen Beschreibung mathematischer Modelle und numerischer Implementierungen diskutiert. Standards wie VMAP, Ontologien wie MathModDB sowie BIM- und STEP-Formate bieten erste Ansätze zur semantischen Modellbeschreibung und zur automatisierten Generierung simulationsfähiger Eingabedaten. Im zweiten Teil wird die Rolle experimenteller Daten für die Validierung von Modellen beleuchtet. Es wird gezeigt, dass hochwertige, strukturierte und maschinenlesbare Validierungsdatensätze essenziell sind, insbesondere für die Bewertung konstitutiver Modelle. Ein weiteres Kapitel widmet sich der Unsicherheitsquantifizierung. Neben klassischen Fehlermaßen werden aleatorische und epistemische Unsicherheiten sowie deren Einfluss auf die Modellbewertung behandelt. Besondere Aufmerksamkeit gilt der Bayes’schen Kalibrierung, der Trennung von Trainings und Testdaten und der Notwendigkeit, auch Begleitversuche aus Materialtests zu dokumentieren. Abschließend wird die Idee einer Benchmarking-Plattform vorgestellt, die auf reproduzierbaren Workflows, automatisierter Provenienzverfolgung und der Nutzung von Research Object (RO) Crates basiert. Diese Plattform erlaubt die dezentrale Veröffentlichung und zentrale Abfrage von Benchmark-Ergebnissen und fördert eine gemeinschaftliche Verifikation und Validierung. Ziel ist es, die Vergleichbarkeit von (Open-Source-)Simulationstools zu verbessern um dadurch komplexe experimentelle Setups zunehmend durch zuverlässige Simulationen ersetzen zu können. T2 - NAFEMS - Symbiose von Simulation und Test CY - Wiesbaden, Germany DA - 12.11.2025 KW - Verification and Validation, KW - Digital twins KW - Virtual lab KW - Uncertainty quantification PY - 2025 SN - 978-1-83979-242-7 SP - 23 EP - 28 PB - NAFEMS CY - Wiesbaden, Germany AN - OPUS4-65271 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Georg, Paul A1 - Block, R. A1 - Heister, W. A1 - Holl, S. A1 - Pulm, A. A1 - Hofmann-Böllinghaus, Anja T1 - A score regarding the need for assistance - considering pedestrians with impairments in evacuation planning N2 - The capabilities of pedestrians for evacuation have a significant impact on the time required to reach a safe place. Usually, the evacuation is split into two main stages: pre-movement-phase and movement-phase. For both a large number of studies investigate different representations of behaviour and impacts. But the influence of impairments is usually not taken into account. In addition, most of the scientific researches focus the investigation of the movement phase. This publication presents a novel approach to score the need for assistance and to estimate the effect on evacuation performance. The proposed score considers characteristic impairments in three dimensions of behaviour: reception, perception and realisation. In an unannounced evacuation training in a sheltered workshop, the evacuation behaviour and pre-movement phase were analysed. The analysis indicates that the pre-movement time depends on the kind of impairment as well as on organisational boundaries. Despite the special needs for assistance, the evacuation process in a sheltered workshop is quite similar to other sub-populations. T2 - 5. Magdeburger Brand- und Explosionsschutztage 2017 CY - Magdeburg, Germany DA - 23.03.2017 KW - Human behaviour KW - Human factors KW - Egress KW - Evacuation KW - Persons with impairments PY - 2017 SN - 978-3-00-056201-3 DO - https://doi.org/10.978.300/0562013 SP - 1 EP - 13 CY - Magdeburg AN - OPUS4-40051 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel A1 - Tschirschwitz, Rico A1 - Kluge, Martin A1 - Askar, Enis A1 - Habib, Abdel Karim A1 - Kohlhoff, Harald A1 - Neumann, Patrick P. A1 - Rudolph, Michael A1 - Schoppa, André A1 - Storm, Sven-Uwe A1 - Szczepaniak, Mariusz T1 - Experimental investigation of failure of LPG gas tanks in passenger cars during full fire development N2 - In continuation of a preceding test series involving sole LPG vehicle tanks, three passenger cars equipped with identical toroidal steel LPG tanks were set on fire. The tanks were installed in the space normally reserved for the spare tyre, in the car boot. No safety device was installed on the tank, in order to force critical failure of the cylinder. Two of the cars were equipped with a tank filled with liquefied propane to a level of 20 % (5.3 kg), the third one was filled completely (25.5 kg). The partially filled tanks failed critically within a time period of more than 20 min after the initiation of the fire. The fully-filled tank did not rupture; the propane was released continuously through a small leak that appeared during the fire. Comprehensive equipment was used to procure measurement data, enabling an analysis of potential consequences and hazards to humans and infrastructure within the vehicle surroundings. The inner status of the tank (pressure, temperature of the liquid phase and the steel casing), the development of the fire (temperature inside and around the vehicle) and the pressure induced in the near-field in case of tank rupture were recorded. The results were analysed in detail and compared against the data gained in tests involving sole, but identical LPG tanks. T2 - FIVE 2018 CY - Boras, Sweden DA - 03.10.2018 KW - Behälterversagen KW - LPG KW - Alternative Antriebe KW - Fahrzeugbrand KW - Auswirkungsbetrachtung PY - 2018 SN - 978-91-88695-95-6 VL - 51 SP - 123 EP - 131 PB - RISE Safety CY - Boras AN - OPUS4-46310 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR ED - Hofmann-Böllinghaus, Anja ED - Anderson, J. T1 - Special issue: Facade fire safety N2 - Façade fires are of growing concern worldwide. Severe facade fires in different parts of the world as well as activities in many countries regarding the testing of facades show the urgency of the fire safety challenges in façade fires. The need for knowledge and a wide Archive of work in this area has become evident after recent incidents which involved extensive facade fires. These include the tragic fires in Dubai and Grenfell Tower in 2017 in the United Kingdom. In many cases, the widespread live news coverage of the events and size of These fires has emphasized the need for progress in the understanding of the processes involved in these fires and put pressure upon the fire safety engineering community to find effective solutions. KW - Testing KW - Safety PY - 2021 UR - https://onlinelibrary.wiley.com/toc/10991018/2021/45/5 SN - 0308–0501 SN - 1099-1018 VL - 45 IS - 5 SP - 583 EP - 696 PB - Wiley CY - Oxford AN - OPUS4-53102 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR ED - Hofmann-Böllinghaus, Anja ED - van Hees, P. T1 - Special Issue on Facade Fire Safety N2 - This Special Issue of Fire and Materials brings together a Collection of papers that were presented at the 2016 Interflam conference in the Fire & Facades session along with recent submissions to the Fire and Materials Journal that are very relevant to the Fire and Facades subject. Having attended the Interflam conference, all Fire and Materials Journal editors who attended realised the importance of this topic. We felt it important that this session content would both be reviewed and made available to a wider audience and that it was timely that we featured this increasing important topic in our journal. Accordingly, authors of selected papers were invited to update and extend their papers for journal submission, and other appropriate peer review papers subsequently submitted to the journal were included in the collection. KW - Editorial PY - 2018 SN - 0308–0501 VL - 42 IS - 5 SP - 463 EP - 577 PB - Wiley CY - London AN - OPUS4-53104 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel A1 - Rudolph, Michael A1 - Tschirschwitz, Rico A1 - Kluge, Martin A1 - Askar, Enis A1 - Habib, Abdel Karim A1 - Kohlhoff, Harald A1 - Neumann, Patrick P. A1 - Schalau, Bernd A1 - Schoppa, André A1 - Storm, Sven-Uwe A1 - Szczepaniak, Mariusz A1 - Mair, Georg W. T1 - Infrared radiation measurement at failure of mobile gas vessels N2 - 15 identical off-the-shelf propane cylinders (m = 11 kg liquid propane) were underfired. The infrared Radiation of the Explosion, that occurred in the aftermath of the vessel failure, was recorded using four bolometers. These measurements are compared with an estimation of the Maximum intensity gained by an Analysis of the Video data, an Extended Version of the Stefan-Boltzmann law and a BLEVE model. T2 - 26th International Colloquium on the Dynamics of Explosions and Reactive Systems CY - Boston, USA DA - 30.07.2017 KW - Failure of gas vessels KW - Propane cylinder KW - Gas explosion KW - Consequences KW - Infrared radiation PY - 2017 SP - 1 EP - 6 PB - FM Global CY - Seattle, USA AN - OPUS4-41993 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Wernicke, Pascal A1 - Hufschläger, Daniel T1 - Pulse compression for air-coupled ferroelectret and thermoacoustic transducers N2 - The main advantage of air-coupled ultrasonic testing is the absence of a liquid couplant, which can damage some materials. However, most air-coupled testing scenarios have the challenge of low signals and a signal-to-noise ratio (SNR) several orders of magnitude lower than with couplant-assisted tech-niques. Since this challenge of small SNR also exists in radar technology, the pulse compression used there was adapted and applied to the physical conditions of air-coupled ultrasonic testing. This paper presents ultrasonic transmission measurements on a carbon-fibre-reinforced polymer plate using two experimental setups: 1) a thermoacoustic transmitter and an optical microphone and 2) a pair of ferroe-lectret transducers as transmitter and receiver. Thermoacoustic transmitters convert electrical energy to heat, which causes the air to expand thus producing acoustic waves. The optical microphone is based on a Fabry-Perot interferometer. Ferroelectrets are charged cellular polymers, having piezoelectric proper-ties and excellent acoustic matching to air. Both thermoacoustic transmitters and ferroelectrets are non-linear regarding the relationship between the excited sound pressure and the excitation voltage. Due to these physical boundary conditions, unipolar coding was used to modulate the excitation signals. Vari-ous codes were tested, and parameters of the excitation pulses were varied to find the optimal combina-tion for each experimental setup. The application of pulse compression to the combination of thermo-acoustic transmitter and optical microphone increased the signal-to-noise ratio by up to 16 dB and for the ferroelectret transducers by up to 23 dB. T2 - 30th International Congress on Sound and Vibration CY - Amsterdam, The Netherlands DA - 08.07.2024 KW - Pulse compression KW - Air-coupled ultrasonic transducers KW - Ferroelectret KW - Thermoacoustics PY - 2024 SN - 978-90-90-39058-1 SP - 1 EP - 7 AN - OPUS4-60725 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -