TY - CONF A1 - Müller, Thoralf T1 - Vorstellung Projektergebnisse Wipano Vorhaben Spanntahlsicherheit N2 - Diese Präsentation stellt die Ergebnisse des abgeschlossenen WIPANO Vorhabens "Spannstahlsicherheit" vor, welches von der BAM in Kooperation mit dem Stahlwerks Annahütte und der Max Aicher GmbH bearbeitet wird. Es werden die Projektziele näher beleuchtet und verschiedentliche Highlights der erzielten Untersuchungsergebnisse vorgestellt. T2 - DIN-Ausschussitzung des NA 062-01-77 AA "Korrosionsprüfverfahren" CY - Berlin, Germay DA - 19.10.2022 KW - Korrosion KW - Spannstahl KW - Spannbetonbauwerke KW - Spannungsrisskorrosion KW - Wasserstoffversprödung PY - 2022 AN - OPUS4-56059 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin A1 - Schukar, Marcus A1 - Krebber, Katerina T1 - Characterizing vibration response of fiber cables for distributed acoustic sensing N2 - The vibration responses of two fiber cables are characterized up to 16 kHz and compared with a standard tight-buffered 900 um fiber. The response of the cables is suppressed due to the cable protection T2 - 27th International Conference on Optical Fiber Sensors (OFS-27) CY - Alexandria, VA, USA DA - 29.08.2022 KW - Response characterization KW - Distributed fiber sensing KW - Acoustic sensing PY - 2022 SP - 1 EP - 4 PB - Optica CY - Washington D.C., USA AN - OPUS4-56096 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin A1 - Schukar, Marcus A1 - Weege, S. A1 - Roske, T. A1 - Krebber, Katerina T1 - Leakage detection at a borehole simulator using distributed acoustic sensing N2 - A distributed acoustic sensing system is used to detect the leakage in a borehole simulator by measuring the leakage induced vibration. The leakage location can be clearly determined by frequency spectrum analysis. T2 - 27th International Conference on Optical Fiber Sensors (OFS-27) CY - Alexandria, VA, USA DA - 29.08.2022 KW - Structural health monitoring KW - Distributed fiber sensing KW - Distributed acoustic sensing KW - Leakage detection PY - 2022 AN - OPUS4-56098 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Thoralf T1 - Abschlussvorstellung Wipano Vorhaben Spanntahlsicherheit N2 - In dem Vortrag werden die Highlights und Ergebnisse des abgeschlossenen Wipano Forschungsprojekts "Spannstahlsicherheit" berichtet. In dem Vorhaben wurde das Projektziel ein neues Prüfverfahren für die Prüfung von Spannstählen auf Spannungsrisskorrosionsempfindlichkeit zu entwickeln erfolgreich abgeschossen. Weiterhin wurden neue Erkenntnisse zu den Ursachen der Ergebnisstreuung der bisherigen Prüfung gemäß ISO 15630-3 gewonnen. Das neue Prüfverfahren soll bei der nächsten Überarbeitungsrunde der ISO 15630-3 als Verfahren zunächst in den informativen Anhang aufgenommen werden. T2 - Arbeitskreissitzung des GfKorr-Arbeitskreises Eisen und Stahl CY - Online meeting DA - 08.12.2022 KW - Korrosion KW - Spannstahl KW - Spannbetonbauwerke KW - Spannungsrisskorrosion KW - Wasserstoffversprödung PY - 2022 AN - OPUS4-56510 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seifert, Lando T1 - Grundlagen Korrosion und Korrosionsschutz - Teil 1: Korrosion metallener Werkstoffe N2 - Innerhalb der Fachausbildung "Kathodischer Korrosionsschutz (KKS)" wurde dieser Vortrag im Grundlagenkurs für erdverlegte Anlagen, Stahlbeton und Innenschutz gehalten. Der 90 min Vortrag befasste sich schwerpunktmäßig mit den Grundlagen der elektrochemischen Korrosion von wichtigen Metallen im Bauwesen: Unleg. Stahl, Aluminium- und Zinkwerkstoffen sowie nichtrostenden Stählen. Galvanische Elemente sowie die Grenzen der elektrochemischen Potentialmessung wurden besprochen. Dies wird anhand einer Reihe von Beispielen verdeutlicht. Der Vortag knüpft die Verbindung zwischen den grundlegenden Korrosionsreaktionen, den äußeren Umgebungsbedingungen, der Korrosionsgeschwindigkeit, dem Faraday'schen Gesetz und den elektrochemischen Stromdichte-Potential-Kurven, mit denen in der Korrosionswissenschaft gearbeitet wird. T2 - Grundlagenkurs für erdverlegte Anlagen, Stahlbeton und Innenschutz; Fachausbildung "Kathodischer Korrosionsschutz (KKS)" CY - Online meeting DA - 28.02.2023 KW - Korrosion KW - Elektrochemische Korrosion KW - Potentialmessung KW - Galvanische Korrosion KW - Bimetallkorroison PY - 2023 AN - OPUS4-57068 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas T1 - Korrosionsarten an geschweißten Bauteilen aus Cr-Ni-Stahl N2 - Die Bedingungen für den schadensfreien Einsatz nichtrostender Stähle, nicht nur bei Schweißverbindungen, sind: 1) Die Passivschicht muss sich vollständig ausbilden können. Voraussetzung dafür sind glatte, blanke, saubere Oberfläche, eine gleichmäßige Elementverteilung, wenig Ausscheidungen und Verunreinigungen. Eine mögliche Beeinflussung der Gefügeausbildung durch Warmumformung und durch die schweißtechnische Verarbeitung sind zu beachten. Anlauffarben müssen durch geeignete geeignete chemische bzw. mechanische Nachbehandlung entfernt werden. 2) Die Repassivierung von Defektstellen unter Einsatzbedingungen muss möglich sein, was durch geeignete Werkstoffauswahl und die Legierungszusammensetzung sicherzustellen ist. Unplanmäßige Betriebszustände oder Störungen können kritische Systemzustände hervorrufen, die die Repassivierung beeinträchtigen oder verhindern. Eine geeignete Unterhaltsreinigung ist sicherzustellen. T2 - Weiterbildung DVS Bezirksverband Chiemgau CY - Trostberg, Germany DA - 02.03.2023 KW - Nichtrostender Stahl KW - Korrosionsverhalten KW - Verarbeitung KW - Fehlerquellen PY - 2023 AN - OPUS4-57150 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Thoralf A1 - Ebell, Gino T1 - Grundlagen der Korrosion N2 - Durch das alkalische Milieu des Porenwassers im Beton ist der Stahl normalerweise dauerhaft vor Korrosion geschützt. Unter ungünstigen Umgebungsbedingungen (Chlorideintrag, Carbonatisierung) kann die passive Deckschicht auf der Stahloberfläche zerstört werden. Der Korrosionsprozess ist initiiert. Die entstehenden Korrosionsprodukte werden zunächst vom Porengefüge des Betons aufgenommen, ohne dass es zu sichtbaren Schäden am Bauwerk führt. Im fortgeschrittenem Stadium der Korrosion können sich dann Risse und Abplatzungen bilden. Um notwendige Sanierungsmaßnahmen sowohl aus sicherheitstechnischen Gründen als auch aus wirtschaftlichen Erwägungen rechtzeitig einzuleiten, sind frühzeitige und weitestgehend zerstörungsfreie Prüfverfahren zur Ermittlung der aktuellen Korrosionswahrscheinlichkeit der Stahlbewehrung von großer Bedeutung. Deshalb finden Methoden und Verfahren zur laufenden bzw. regelmäßigen Korrosionsüberwachung von Stahlbetonbauwerken ständig größere Beachtung, sowohl im Bereich Forschung und Entwicklung als auch in der Praxis. Die elektrochemische Potentialfeldmessung ist ein etabliertes und weit verbreitetes Verfahren zur Beurteilung des Korrosionszustandes der Bewehrung in Stahlbetonbauwerken. Mit Hilfe dieses Verfahrens können Bereiche korrodierender Bewehrung zerstörungsfrei lokalisiert werden. In der Regel kommt diese Methode bei der Detektion von chloridinduzierter Korrosion zum Einsatz. Der Lehrgang vermittelt den Teilnehmenden in kompakter Form einen zusammenfassenden Überblick über die notwendigen Grundlagen zum Verständnis der Messmethode, der Vorbereitung und Durchführung der Messungen, der notwendigen Begleituntersuchungen sowie der Interpretation der gewonnenen Daten. Der erste Tag ist der theoretischen Ausbildung gewidmet, am zweiten Tag folgt dann die praktische Anwendung der Lerninhalte. Am dritten Tag folgt die Abnahme der praktischen und theoretischen Prüfung zur Erlangung des Sachkundenachweises. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen CY - Berlin, Germany DA - 24.04.2023 KW - Potentialfeldmessung KW - Korrosion PY - 2023 AN - OPUS4-57493 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Reduction in Train-Induced Vibrations—Calculations of Different Railway Lines and Mitigation Measures in the Transmission Path N2 - The reduction in train-induced ground vibrations by different railway lines and by mitigation measures in the propagation path was analysed in a unified approach by two-dimensional finite element calculations. In general, there was no reduction at low frequencies, and the reduction be-came stronger with increasing frequencies. A maximum reduction of 0.1 at high frequencies was established with an open trench. Reductions between 0.7 and 0.2 have been found for the other sit-uations, filled trenches, walls, plates, and blocks, as well as for railway lines on dams, in cuts and in a tunnel. Bridges can produce amplifications due to their resonance frequencies, but also strong reductions due to massive bridge piers. The influence of some parameters has been analysed, such as the bridge span, the inclination of the dam and the cut, the stiffness of the soil, and the tunnel structure. The dynamic track stiffnesses of a surface, bridge, and tunnel track have been calculated using the 3D finite-element boundary-element method for comparison with corresponding meas-urements. KW - Train-induced vibration KW - Mitigation KW - Trench KW - Obstacles KW - Tunnel KW - Bridge KW - Finite element KW - Boundary element PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-579573 DO - https://doi.org/10.3390/app13116706 VL - 13 IS - 11 SP - 1 EP - 19 PB - MDPI CY - Basel AN - OPUS4-57957 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Site-specific amplitude-distance laws, wave velocities, damping, and transfer functions of the soil from hammer impacts and application to railway-induced ground vibration – Similarities and mid-frequency differences N2 - The propagation of ground vibrations is theoretically analysed with frequency-wavenumber and simplified methods. Experimental methods are presented which can characterise the site-specific ground vibrations by wave velocities, stiffness and damping. Measurements with hammer and train excitation have been performed at several sites. The one-third octave spectra show the stiffness-dependent amplitudes and the low- and high-frequency filter effects due to the layering and the damping of the soil. Specific train effects, an additional high-frequency filter, the sleeper passage frequency, and an amplified mid-frequency component can be clearly found. The attenuation with distance is analysed in detail where the theoretical exponential and the empirical frequency-dependent power law are considered. Hammer and train excitation show the same site-specific effects which are mainly due to the stronger or weaker damping of the soil. The train attenuation is generally weaker than the hammer attenuation. The attenuation exponent of the power law, which is strongly dependent on the site and the frequency, is reduced for the train vibration by 0.3 to 0.5 in agreement with the theory. Reasons are discussed for the overall power law and for the dominating mid-frequency component. KW - Hammer impact KW - Train passage KW - Layered soil KW - Attenuation KW - Filter effects KW - Randomly heterogeneous soil KW - Scattering PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-585020 DO - https://doi.org/10.1007/s42417-023-01095-0 SN - 2366-2557 SP - 1 EP - 17 PB - Springer AN - OPUS4-58502 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz A1 - Song, Jiaojiao T1 - Dynamic damage detection of slab tracks – finite element models on Winkler soil and finite-element boundary-element models on continuous soil N2 - The train passages over intact or damaged slab tracks on different soils have been calculated by two methods. The finite element method (FEM) uses a Winkler soil under the track model by adding a thin “soil layer”. The combined finite element boundary element method has a continuous soil model which is included by the boundary element method. The basic results are the distributions of the track (rail, track plate, and base layer) displacements along the track for a single axle laod. These solutions are superposed to a complete train load and transformed to time histories. The influence of track and soil parameters has been analysed. The main interest is the influence of the track damage. A gap between track plate and base layer of different lengths has been studied for changes in amplitudes and widths of deflection. A best fit to measured track displacements has been found so that the track damage can be identified and quantified. The FEM model with Winkler soil cannot be fitted to the amplitude and width with the same soil parameters. Therefore, the FEBEM model is preferable for these railway track problems. KW - Track damage quantification KW - Finite element method KW - Combined finite-element boundary-element method PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-562207 DO - https://doi.org/10.3390/civileng3040055 SN - 2673-4109 VL - 3 IS - 4 SP - 979 EP - 997 PB - MDPI CY - Basel AN - OPUS4-56220 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - BOOK A1 - Mair, Georg W. T1 - Sicherheitsbewertung von Composite-Druckgasbehältern - Potential statistischer Methoden jenseits aktueller Vorschriften N2 - Das Buch zeigt einen alternativen Weg der Sicherheitsbeurteilung von Druckbehältern aus Faserverbundwerkstoffen. Dies ist insbesondere für die Mobilität der Zukunft und die zugehörige Energieversorgung mit Bio-/Erdgas und Wasserstoff von Interesse. Mit statistischen Methoden gelingt es, die Sicherheit auch jenseits der Grenzen aktueller Vorschriften fundiert zu beurteilen. Es wird dargelegt wie eine probabilistische sicherheitsbeurteilung als Alternative aussehen könnte. Dieser Ansatz basiert auf neuen Verfahren der zerstörenden Prüfung und statistischer Auswertung relevanter Festigkeitseigenschaften. Hierzu zählen die langsame Berstprüfung und ein spezielles Arbeitsdiagramm zur Auswertung von Stichproben. Darüber hinaus erlaubt der Ansatz die Quantifizierung der Degradation im Betrieb und zeigt Wege zur Abschätzung der Lebensdauer. Sicherheit wird diskutiert als Kombination von Überlebenswahrscheinlichkeit und Konsequenz. N2 - A detailed analysis of current approval requirements and relevant safety assessment methods for gas cylinders is given. With a focus on composite cylinders for storing compressed natural gas and hydrogen, this book demonstrates how current regulations and standards limit the ability to reduce cost and weight. Based on this data, it then highlights the potential offered by a new, probabilistic safety assessment standard. After addressing the economic potential of probabilistic safety assessment, the book details working procedures and the improvement of cycling and (slow) burst tests as methods for residual strength assessment. This is followed by methods for the statistical evaluation of test data, as well as considerations of samples size and character of distribution. A definition of sample strength is elaborated in terms of the “Sample Performance Chart” developed by the author. On this basis, safety is discussed as a property of service life and interpreted as an issue of degradation, before aspects of artificial aging for simulating the reliability level at end of life are discussed. Lastly, the book considers testing and inspection aspects: quality of production, degradation prediction by means of destructive sample tests parallel to operation, retesting periods, and correcting for under- and overestimates of safe lifetime. Presented in schematic diagrams, illustrations and tables, this information will enable manufacturers and operators to use this new approach in practice and support the improvement of current regulations and standards. KW - Sicherheitsbewertung KW - safety assessment KW - Streuung KW - scatter KW - Probabilistischer Ansatz KW - probabilistic approach KW - Gasspeicherung KW - gas storage KW - Faserverbundwerkstoffe KW - composite materials (FRP) PY - 2016 SN - 978-3-662-48131-8 SN - 978-3-662-48132-5 DO - https://doi.org/10.1007/978-3-662-48132-5 SP - VII - XIX, 1 EP - 303 PB - Springer Vieweg CY - Berlin Heidelberg ET - 1 AN - OPUS4-35664 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Die Over-moulded cylinders (OMC) - Hintergrund zur neuen SV 674 N2 - Nach Phasen der nationalen Anwendung und dann eines multilateralen Agreements kommen die Beschaffenheitsanforderungen für sog. "over-moulded Cylinders" (umformte Flaschen) in das internationale Regelwerk. Aufgrund ihrer strukturellen Besonderheiten können jedoch nicht alle Formen der wiederkehrenden Prüfung auf diese Flaschen angewendet werden. Der Ausgleich dieses Defizits erforderte die mehrjährige Arbeit einer Arbeitsgruppe der gemeinsamen Tagung (UN ECE und OTIF) unter sehr engagierter Mitarbeit der BAM bis ein alternativer Ansatz hinreichend Zustimmung für die Aufnahme ins Regelwerk fand. Das vorgestellte Grundkonzept basiert auf der zerstörenden Prüfung einer definierten Anzahl von Gasflaschen zu klar geregelten Zeitpunkten. Auf Basis der statistischen Auswertung der Ergebnissen sollen mögliche Fertigungsfehler oder unerwartet schnelle Alterungsprozesse gefunden werden können, ohne dass es zu Versagensfällen kommt. Prüfungen, die technisch aussagekräftig durchgeführt werden können, bleiben obligatorisch. T2 - DVFG Forum Flüssiggas 2018 CY - Leipzig, Germany DA - 12.06.2018 KW - Flüssigkeitsdruckprüfung KW - Berstprüfung KW - Außenbesichtigung KW - Abschälprüfung KW - Adhäsionsprüfung KW - Rückverfolgbarkeit PY - 2018 AN - OPUS4-45480 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Möglichkeiten der BAM zur Prüfung von GasflascheN und Druckbehältern N2 - Der Vortrag beginnt mit der Arbeitshypothese, dass das zentrale Maß für die Qualität der Fertigung die Streuung der Eigenschaften der gefertigten Produkte ist. Auf dieser Basis wird eine Reihe von Prüfanlagen für die zerstörende Festigkeitsermittlung und zerstörungsfreie Vergleiche von Druckbehältern einschließlich zugehöriger statistischer Betrachtungen vorgestellt. T2 - Workshop zur Kooperation mit BASF auf dem Gebiet der additiven Fertigung CY - BAM, Berlin, Germany DA - 04.04.2018 KW - Berstprüfung KW - Lastwechselprüfung KW - Schallemissionsanalyse KW - Langsame Berstprüfung KW - Falltest KW - Brandprüfung KW - Beschussprüfung KW - Statistische Bewertung PY - 2018 AN - OPUS4-45467 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Spode, Manfred A1 - Mair, Georg W. T1 - Monte Carlo Simulation - Prinzip und Beispiel N2 - Die Monte-Carlo-Simulation ist eine geeignete Methode, um Festigkeitseigenschaften wie z.B. Berstdruck, oder auch die Lastwechselfestigkeit von ganzen Population von Druckbehältern zu simulieren. Dies erlaubt wiederum die systematische Analyse der Wirksamkeit von deterministischen Mindestanforderungen und die Optimierung entsprechender Zulassungsvorschriften. T2 - BAM-Kolloquium der 3. Abteilung CY - BAM Berlin, Germany DA - 08.11.2018 KW - Monte Carlo Simulation KW - Faserverbundwerkstoffe KW - Druckbehälter KW - Berstfestigkeit KW - Lastwechselfestigkeit PY - 2018 AN - OPUS4-46628 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Sicherheitsforschung im Bereich Wasserstoff – Transport von CGH2 N2 - Ein Aspekt des Gefahrguttransportes, der an Bedeutung in den letzten Jahren zugenommen hat, ist die Versorgung von Wasserstofftankstellen und anderen H2-Großverbrauchern über die Schiene aber insbesondere über die Straße. Mit Blick auf die primäre Form der Speicherung wird der Begriff der Sicherheit über den Aspekt der Häufigkeit eines definierten Ereignisses erläutert und auf die Besonderheiten der Druckgefäße aus Verbundwerkstoffen hingewiesen, wie auch den regulatorischen Hintergrund der Lebensdauerüberprüfung nach 15 Jahren nach den Vorgaben der zuständigen Behörde. In Deutschland sind diese Vorgaben in der BAM-Gefahrgutregel 021 geregelt, die in der GGR 022 durch eine Regelung zur Wiederkehrenden Prüfung dieser Umschließungen ergänzt wird. Beide BAM-Gefahrgutregeln basieren auf einem probabilistischen Ansatz und einer Konsequenzabschätzung über das Druck-Volumen-Produkt der Druckgefäße. Die neu im Recht verankerte EN 17339 ist die erste Norm, die speziell fest montierte Compositespeicher für den Wasserstofftransport regelt. Sie ermöglicht eine erhebliche Gewichtreduktion und führt eine Obergrenze für das Druckvolumen ein. Es wird kurz erläutert, dass gerade mit Blick auf Wasserstofftransporte über eine Arbeitsgruppe der Vereinten Nationen eine Begrenzung des Konsequenzpotentials in das internationale Recht eingeführt werden soll und welche Kriterien bei der systematischen Ermittlung des akzeptierten Wertes von 1.5 Mio bar Liter Einfluss haben. Mit Blick auf die Energiewende sieht es die BAM als besonders wichtig an, die Transportkosten zu senken, indem der Prüfaufwand reduziert und gleichzeitig die Erkenntnistiefe aus der betrieblichen Überwachung verbessert wird. Hierzu muss die Datenbasis für die probabilistische Bewertung der Lebensdauer von zerstörenden Prüfungen auf zerstörungsfreie Prüfungen umgestellt werden und idealerweise die 100% Prüfung zumindest in der ersten Hälfte des sicheren Lebens auf Stichproben reduziert werden. Dies und andere Aufgaben, die wichtig für eine sichere und attraktive Wasserstoffwirtschaft sind werden von dem Kompetenzzentrum H2Safety@BAM bearbeitet, dass in seinen Grundzügen kurz vorgestellt wird. T2 - IAA Transportation 2022 CY - Hannover,Germany DA - 20.09.2022 KW - H2Safety@BAM KW - Markthochlauf KW - Lebensdauervorhersage KW - zerstörungsfreie Prüfung ZfP KW - Risikosteuerung PY - 2022 AN - OPUS4-56984 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Current work at BAM on composite-cylinders in fire N2 - The presentation gives information about several activities of BAM on the issue of fire engulfment tests of onboard gas storage systems. T2 - Advisory Board of the SUPERGEN Challenge project "Integrated safty strategies for onboard H2-storage" CY - Hangzhou, China DA - 19.04.2016 KW - Fire engulfment tests KW - Competence of BAM KW - Car crash KW - Gas explosion PY - 2016 AN - OPUS4-35958 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Probabilistic approval approach - Safety and economic aspects of minimum burst and load cycle requirements N2 - This presentation provides the main issue of a probabilistic based safety assessment. It shows the differences in terms of survival rate between some current deterministic standards and the probabilistic approach. It deals with three test procedures: slow burst test, cycle test and fire engulfment test. T2 - INTERNATIONAL CONFERENCE HYDROGEN BRIDGE 2016 - Safety of high-pressure hydrogen storage CY - Hangzhou, China DA - 21st APRIL 2016 KW - Slow burst test KW - Cycle strength KW - End of life KW - Degradation KW - Lucky punch area PY - 2016 AN - OPUS4-35960 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - de Miguel, N. A1 - Mair, Georg W. A1 - Acosta, B. A1 - Szczepaniak, Mariusz A1 - Moretto, P. T1 - Hydraulic and pneumatic pressure cycle life test results on composite reinforced tanks for hydrogen storage N2 - Current standards governing the design, qualification and in-service inspection of carbon fibre composite cylinders do not facilitate to optimise cylinder design. The requirements have been adapted from standards for metallic cylinders and cannot easily quantify the degradation processes in composite materials. In this article, the results of hydraulic and hydrogen pressure cycle life tests performed on composite reinforced tanks with a metal liner (type 3) and with a high density polymer liner (type 4) are shown. Moreover, the degradation measured by means of residual strength of the tanks after the cycling tests have been compared. It has been found that the most critical aging for metal based composite cylinder is the gaseous cycling while type 4 designs seem to be more sensitive to hydraulic cycling at high temperature. T2 - ASME 2016 Pressure Vessels and Piping Conference CY - Vancouver, British Columbia, Canada DA - 17.07.2016 KW - Composite reinforced tanks KW - Compressed hydrogen storage KW - Design and qualification standards KW - Pressure cycle life tests KW - Safety factors PY - 2016 SN - 978-0-7918-5035-0 VL - 1A SP - 63568-1 EP - 63568-10 PB - ASME CY - Vancouver, British Columbia, Canada AN - OPUS4-36275 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Becker, Ben A1 - Mair, Georg W. A1 - Klauke, André T1 - Einfluss der Unsicherheiten von Stichprobenprüfungen auf die Sicherheitsbewertung von Composite-Druckgefäßen N2 - Viele Konzepte zur Sicherheitsbewertungen beruhen auf der Untersuchung weniger, oder einzelner Prüfergebnisse. Aber auch im Fall umfangreicherer statistischer Untersuchungen können nur begrenzte Stichproben untersucht werden. Mittelwerte und Streuung kleiner Stichproben weichen mehr oder weniger von den wahren Eigenschaften des untersuchten Baumusters ab. Solche Abweichungen werden derzeit nicht oder nur sehr vage berücksichtigt. In diesem Aufsatz wird der Einfluss der Unsicherheiten aus Stichproben anhand der Bewertung von Composite-Druckgefäßen durch Berst- und Lastwechselprüfungen dargestellt. KW - Akzeptanzwahrscheinlichkeit KW - GTR 13 KW - Überlebenswahrscheinlichkeit KW - Langsame Berstprüfung KW - Stichprobenumfang KW - Lastwechselprüfung PY - 2016 SN - 2191-0073 VL - 6 IS - 7/8 SP - 27 EP - 33 PB - Springer-VDI-Verlag CY - Düsseldorf AN - OPUS4-37061 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Probabilistic safety assessment of composite gas cylinders - Safety and economic aspects of minimum burst and load cycle requirements N2 - This presentation shows the most important steps for developing the probabilistic approach PA with a lot of detailed information on test results. It discusses the necessitiy of performing a slow burst test, to which amount degradation can be accepted and how these interacts with aspects of costs etc. T2 - SAE - Fuel Cell Safety Task Force CY - Torrance, CA, USA DA - 8th March 2016 KW - Saving effort KW - Sample performance chart KW - Degradation KW - Lucky punch arey KW - Confidence level KW - Survival rate PY - 2016 AN - OPUS4-35961 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Probabilistic safety analysis of CPVs – Comparison PA vs. ISO 11119 and GTR13 N2 - The presentation shows the basics on the graphic comparison of deterministic regulations and probabilistic safety requirements. In doing so, unsafe but approvable areas in the BAM-SPC (sample performance chart) becomes obvious; as the area of not approveable but safe strength properties does. Finally the semi-porbabilistic approach of GTR#13 (global technical regulation for hydrogen vehicles) is analysed. Relevant figures show again potential of saving material and unsafe areas in case of high scatter at end of life. T2 - PHASE convention 2016; dissimination event of the COPERNIC project (COst and PERformaNce Improvement for Cgh2 composite tanks; EU FP7) CY - De Hoorn in Leuven, Belgium DA - 24.05.2016 KW - Composite cylinders KW - Reliability KW - Deterministic KW - Degradation KW - End of life PY - 2016 AN - OPUS4-36255 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric T1 - Full-scale bonfire test N2 - Explanation of the test setup, intention and assessment of a Full-Scale Bonfire Test T2 - Follow-up Workshop on statistical safety assessment CY - BAM TTS, Horstwalde, Germany DA - 05.10.2016 KW - Full scale bonfire test KW - Composite cylinder PY - 2016 AN - OPUS4-37836 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF ED - Saul, Herbert ED - Mair, Georg W. T1 - Proceedings Follow-up Workshop on Statistical Safety Assessment of Composite Cylinders from Mass Production N2 - Printed collection of important information about the workshop, wellcome of the president, list of participants, literature and a lot of documents and work sheets in addition to the elictronically distributed presentations T2 - Follow-up Workshop on Statistical Safety Assessment of Composite Cylinders from Mass Production CY - BAM Berlin, Germany DA - 05.10.2016 KW - Composite cylinders KW - Probabilistic approach KW - Statistical assessment PY - 2016 SP - 1 EP - 90 PB - Eigenverlag CY - Berlin AN - OPUS4-38948 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - UN-service life checks by statistical methods N2 - This slides explain the functionality and the procedure of the UN-service life checks as they are operated by BAM as German authority. These are based on the probabilistic approach including evaluation of current safety level and its comparison with assessments of different status of degrdation including extrapolation towards end of safe service life. The similarity to the approach for determiantion of retest periods by BAM is explained. T2 - Follow-up Workshop on Statistical Safety Assessment of Composite Cylinders from Mass Production CY - BAM-Berlin, Germany DA - 05.10.2016 KW - Life time determination KW - UN-service life check KW - Periodic insepction KW - Trace of degradation KW - Acceptance of failure rates PY - 2016 AN - OPUS4-38955 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Step by step assessment of test results from composite cylinders N2 - Repetition of the main aspects about the assessment of sample test results of the 1st and 2nd workshop on statistical safety assessment T2 - Follow-up Workshop on Statistical Safety Assessment of Composite Cylinders from Mass Production CY - BAM Berlin, Germany DA - 05.10.2016 KW - Cycle strength KW - Slow burst test KW - Statisitcal evaluation KW - GAUSSian net PY - 2016 AN - OPUS4-38951 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - In-service degradation - a lack of knowledge N2 - The slides explain different meanings and aspects of degradation; the relevant slides show effects to be measured by destructive tests and their graphical evaluation in SPCs T2 - Follow-up Workshop on Statistical Safety Assessment of Composite Cylinders from Mass Production CY - BAM Berlin, Germany DA - 05.10.2016 KW - Artifical aging KW - Gaseous filling KW - Combined distribution KW - Extrapolation of degradation KW - Confidence level KW - End of life PY - 2016 AN - OPUS4-38954 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - The sample performance chart & its use for the display of degradation N2 - Display and graphical interpretation of statistically evaluated sample properties; Including assessment of degradation respectivelly aging T2 - Follow-up Workshop on Statistical Safety Assessment of Composite Cylinders from Mass Production CY - BAM Berlin, Germany DA - 05.10.2016 KW - Sample performance chart KW - Mean strength KW - Scatter value KW - Degradation PY - 2016 AN - OPUS4-38952 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Bridge monitoring using embedded ultrasonics First results from the BLEIB reference structure N2 - The BLEIB reference structure The structure is a two-span, 24 m long inverse u-shaped post-tensioned concrete beam. Fibre optic sensing cables, RFID sensors and ultrasonic transducers are permanently embedded. Other sensing techniques (vibrational, optical, ultrasonic, mechanical) are applied externally. Tension can be adjusted. Loads can be placed at arbitrary locations. Limited damage is introduced to one span. The BLEIB reference structure is located at BAM‘s test site in Horstwalde, south of Berlin. Ultrasonic transducer before concreting. Embedded ultrasonic transducers 14 piezo transducers have been embedded before concreting. They are located in five sections, two close to the centers of both spans respectively and one above the central bearing. Load experiment and data evaluation In a first experiment load 2 (weight 2 t) was moved three times along the southern (right) span. The tension forces were modified as well. Ultrasonic transmission measurements were repeated over time and evaluated using Coda Wave Interferomerry (CWI), which determines correlation coefficients and relative velocity changes as subtle indicators for loads and other changes in the material. T2 - New mathematics for a safer world: wave propagation in heterogeneous materials CY - Edinburgh, UK DA - 12.06.2017 KW - Bridge monitoring KW - Ultrasound KW - Embedded transducers KW - Coda wave interferometry PY - 2017 AN - OPUS4-40578 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Niederleithinger, Ernst A1 - Katzenbach, R. A1 - Klingmüller, O. A1 - Hillmann, S. A1 - Willmes, Michael T1 - REFUND: Untersuchung von Bestandsgründungen für eine Entscheidung zur Wiedernutzung T1 - REFUND: Investigation of existing foundations and decision making before re-use N2 - Vor einer geplanten Weiter- oder Wiedernutzung von Bestandsgründungen stellt sich die Frage nach deren Lage, Geometrie und Zustand im Untergrund. Hierfür gibt es verschiedene Prüfverfahren. Die Abläufe bei Planung und Prüfung sind jedoch bisher nicht standardisiert und die Möglichkeiten bzw. Grenzen der Prüfverfahren den Planern wenig bekannt. Im Forschungsprojekt REFUND (2014–2016) wurden unter Berücksichtigung der aktuellen Normen und des Stands der Technik Ablaufdiagramme für die Planung der Wiedernutzung sowie die Untersuchung des Bestands entwickelt. Dies geschah getrennt für Einzel- und Streifenfundamente, Platten und Pfähle. An zwei Praxisbeispielen wurden die Abläufe getestet und optimiert. Die Ergebnisse wurden in einem Handbuch zusammengefasst. Es soll Planer und andere Verantwortliche bei der wirtschaftlich und technisch optimierten Durchführung von Wiedernutzungsprojekten unterstützen. N2 - Before re-using existing foundations they have to be investigated for position, geometry and condition in the subsurface. The procedures and protocols haven't been standardized yet. Capabilities and limitations of appropriate testing methods are not known to all stakeholders. In the frame of the research project REFUND (2014-2016) we have developed decision trees for the planning and the investigation process, separately for single and strip foundations, slabs and piles. The protocols were tested in line with two actual projects. The results have been compiled in a handbook, which will support planners and other participants in a technical and economical optimized way to perform re-use of foundations. KW - Fundament KW - Wiedernutzung KW - Entscheidung KW - Zerstörungsfrei PY - 2017 DO - https://doi.org/10.1002/bate.201700038 SN - 1437-0999 VL - 94 IS - 10 SP - 676 EP - 681 PB - Ernst & Sohn CY - Berlin AN - OPUS4-42615 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiggenhauser, Herbert T1 - Acoustic and electromagnetic waves in nondestructive testing in civil engineering N2 - Research and Development; Application of NDT for Civil Structures; Reference Specimen; Validation of Testing Solutions; Standardization; Training; Structural Investigation (thickness, location of elements, cracks, ...); Material Properties (strength, composition, moisture, …) T2 - WAVES Workshop Cambridge CY - Cambridge, UK DA - 26.03.2017 KW - Acoustic KW - Electromagnetic KW - Waves PY - 2017 AN - OPUS4-39629 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mark, Peter A1 - Sanio, David A1 - Balzani, Daniel A1 - Curoșu, Iurie A1 - Hafner, Annette A1 - König, Markus A1 - Kuhlenkötter, Bernd A1 - Thewes, Markus A1 - Baille, Wiebke A1 - Hackl, Klaus A1 - Hagedorn, Philipp A1 - Meschke, Günther A1 - Nestorović, Tamara A1 - Neu, Gerrit Emanuel A1 - Sauer, Roger A1 - Tafili, Merita A1 - Vogel, Andreas A1 - Weber, Sebastian A1 - Wichern, Marc A1 - Wichtmann, Torsten A1 - Niederleithinger, Ernst A1 - Freitag, Steffen A1 - Menges, Achim A1 - Simon, Sven T1 - Modulares Wiederverwenden von Bestandstragwerken T1 - Modular reuse of existing load-bearing structures N2 - Natürliche Prozesse laufen im Kreislauf ab. Auf Vergehen folgt gleichwertiges Entstehen. Solch ein Zirkularitätsprinzip ist im Tragwerksbau nicht verankert. Nach Nutzungsende werden Bauwerke abgebrochen, falls möglich zerlegt und recycelt. Besonders davon betroffen ist die Stahlbetonbauweise mit ihrem enormen Baubestand. Abbruch löst ein fatales Downcycling aus, mit minderwertigem Betoneinsatz als Schüttgut oder Deponierung. Selten besiegeln dabei Tragfähigkeitsdefizite das Nutzungsende, vielmehr sind Nutzungseinschränkungen oder baurechtliche Schranken ausschlaggebend. Die Folgen sind eine enorme Verschwendung an Ressourcen wie Sand oder Kies, Treibhausgasemission zur Aufbereitung und Abfall. Wiederverwenden (engl. reuse) bedeutet ein erneutes Nutzen von Stahlbeton als Bauteil (Modul). Nicht mehr genutzte Tragwerke werden dazu in die noch tragfähigen Anteile zerlegt, in ihren Eigenschaften charakterisiert, aufgearbeitet und baukastenartig zu neuen Tragwerken zusammengefügt. Es entsteht ein kreislauffähiges Modulsystem. Der Sonderforschungsbereich 1683 mit Sprecherschaft an der Ruhr‐Universität Bochum befasst sich mit dieser Art der modularen Wiederverwendung und erarbeitet Entwurfs‐ und Reparaturkonzepte für Tragwerke aus wiederverwendetem Stahlbeton, automatisierte Charakterisierungs‐ und Aufarbeitungsverfahren sowie Prozessmethoden für Logistik, Dekonstruktion und die Nachhaltigkeitsbewertung. Der Beitrag stellt die Konzepte und Demonstratoren möglicher Tragwerke vor. N2 - Natural processes run in cycles. On decay follows full regeneration. Such circularity is not yet rooted in the principles of structural engineering. At the end of service, buildings are demolished and, when feasible, disassembled for recycling. This also applies to reinforced concrete construction with its vast building stock. Demolition triggers a fatal downcycling process in which the concrete is used as bulk material or disposed of in a landfill. However, near the end of service, capacity deficits are seldom the key factor; utilization limits or construction regulations are decisive instead. The consequences are an enormous waste of resources, such as sand or gravel, greenhouse gas emissions from reprocessing and waste. Reuse means the repeated use of reinforced concrete as structural components (modules). No longer needed buildings are deconstructed into load-bearing elements, characterized, refurbished, and assembled into new modular structures, creating a circular modular system. The Collaborative Research Center 1683 at Ruhr University Bochum is a multidisciplinary cooperation addressing modular reuse. It develops design and repair concepts for load-bearing structures made of reused reinforced concrete, automated characterization and processing, and processes for logistics, deconstruction, and sustainability assessment. This paper presents early concepts and demonstrators of such envisaged structures. KW - Wiederverwendung KW - Kreislaufwirtschaft KW - Stahlbeton KW - Nachhaltigkeit KW - Modulares Bauen KW - Automatisierung KW - Reuse KW - Circular economy KW - Reinforced concrete KW - Sustainability KW - Modular construction KW - Automation PY - 2025 DO - https://doi.org/10.1002/bate.70000 SN - 0932-8351 VL - 102 IS - 8 SP - 424 EP - 435 PB - Ernst & Sohn CY - Berlin AN - OPUS4-64015 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Seifert, Lando A1 - Müller, Thoralf A1 - Bettge, Dirk A1 - Moersch, Jörg A1 - Isecke, Bernd A1 - Ebell, Gino T1 - Stress Corrosion Tests for Prestressing Steels—Part 2: Susceptibility of Quenched and Tempered Wires—Influence of Chromium N2 - Due to the risk of failure in existing prestressed concrete bridges, the assessment of the susceptibility of prestressing steel to hydrogen‐induced stress corrosion cracking will become more important in the future. At present, the used normative ISO 15630‐3 test gives unpersuasive and diverging results using a free corrosion approach for the needed hydrogen charging for stress corrosion cracking initiation. A newly developed test method uses the cathodic polarization to control the supply of electrons for hydrogen charging instead of an uncontrolled and variable supply of electrons by metal dissolution during free corrosion. Experimental data shows a reliable differentiation between highly susceptible known quenched and tempered wires and robust cold‐drawn wires with this new test. A round robin with eight participating testing institutes demonstrated the reproducibility of results testing a cold‐drawn wire batch of St 1470/1670. In contrast to previously reported experience in the literature, the new method ranks the Cr‐alloyed quenched and tempered (“new‐type”) wires as highly‐susceptible as the “old‐type” wires without Cr‐alloy. KW - Cathodic polarization KW - Chemical composition KW - Chromium KW - Prestressing steels KW - Quenched and tempered KW - Stress corrosion cracking KW - Susceptibility KW - Wires PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639735 DO - https://doi.org/10.1002/maco.70033 SN - 0947-5117 SP - 1 EP - 10 PB - Wiley-VCH CY - Weinheim AN - OPUS4-63973 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häberle, Nicolas T1 - Opportunities of advanced viscoplastic material modelling for the numerical prediction of thermal and residual stresses in high-strength low-alloy steel welds N2 - The accurate numerical prediction of thermal stresses, residual stresses, and distortions in high-strength low-alloy steel welds is challenging due to the steels’ complex hardening, viscoplastic, and phase transformation behaviour. This work demonstrates the opportunities of applying an advanced viscoplastic material model for the numerical simulation of a single-pass gas-metal arc (GMA) weld using steel of grade S960QL. A very good agreement was found between numerically predicted and experimentally measured residual stresses. The opportunities of advanced viscoplastic material modelling in computational welding mechanics (CWM) are further demonstrated by comparing the simulation results with those obtained by applying a classic rate-independent isotropic hardening approach. The numerical simulations did show that simple isotropic hardening formulations result in inaccurate predictions of residual stresses for non-austenitized base material within the heat affected zone (HAZ). N2 - Potentiale durch verbesserte Materialmodellierung bei der numerischen Prognose von Eigenspannungen, thermischen Spannungen und Verzug bei einer einlagigen S960QL Metallschutzgasschweißung. T2 - 10th International Conference on Trends in Welding Research CY - Hitotsubashi Hall, Tokyo, Japan DA - 11.10.2016 KW - Chabochemodell KW - Schweißen KW - Numerische Simulation KW - High-strength low-alloy steel KW - Computational welding mechanics KW - Residual stress KW - Material modelling PY - 2016 AN - OPUS4-38127 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Inspection and monitoring of massive concrete structures by innovative ultrasonic methods N2 - Presentation on recent progress in ultrasinic testing and monitoring of concrete for massive structures. First, a new instrument (LAUS) for ultrasonic echo testing of thicknesses up to 5 m is shown. A new method to provide better images of the concrete interior, Reverse Mitem Migration (RTM)is presented. Second, the use of embedded ultrasonic transducers and data processing methods borrowed from seismology to detect subtle changes in concrete are documented. T2 - NUCCON 2016 CY - Helsinki, Finland DA - 31.10.2016 KW - Ultrasound KW - Concrete KW - Imaging KW - Monitoring KW - Nuclear PY - 2016 AN - OPUS4-38181 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fabry, Çağtay T1 - Data-based process monitoring and control in narrow-gap GMAW N2 - An experimental setup to integrate laser sensor into conventional GMAW setups via a unified control architecture is described. The setup is used to automate and monitor narrow-gap GMAW and control the electrode weaving motion as well as the resulting height of each weld layer. A way to develop GMAW arc-sensors using artificial neural networks using the setup is shown. The control system is connected to a relational database to store various process measurements. The database can be accessed to filter previous weldments by numerous criteria which allows modelling of process parameter correlation among vast datasets. Such models can be used for process monitoring and control in future applications. T2 - 69th IIW Annual Assembly CY - Melbourne, Australia DA - 10.07.2016 KW - Arc-sensing KW - Künstliche neuronale Netze KW - Artificial neural networks KW - GMAW control KW - Narrow gap GMAW KW - Profile measurement KW - Lichtbogensensorik KW - MAG Prozesssteuerung KW - MSG-Engspaltschweißen KW - Profilvermessung PY - 2016 AN - OPUS4-38291 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fabry, Çağtay T1 - Automatisierungs- und Regelkonzepte für das MSG-Engspaltschweißen N2 - Es wird ein Versuchsstand zum automatisierten MSG-Engspaltschweißen mit integrierter Lasersensorik zur Prozessteuerung und -überwachung vorgestellt. Die Funktion einer Lichtbogensensorik zur automatischen Steuerung der mechanischen Elektrodenauslenkung wird erläutert und verschiedene Anwendungsfälle an Beispielen demonstriert. Die zusätzliche Füllgradregelung beim Mehrlagenschweißen mit veränderlichem Nahtquerschnitt auf Basis der optischen Messtechnik wird zudem vorgestellt. T2 - WGF Assistentenseminar 2016 CY - Paewesin, Germany DA - 06.09.2016 KW - Künstliche neuronale Netze KW - Arc-sensing KW - Lichtbogensensorik KW - MAG Prozesssteuerung KW - MSG-Engspaltschweißen KW - Profilvermessung KW - Artificial neural networks KW - GMAW control KW - Narrow gap GMAW KW - Profile measurement PY - 2016 AN - OPUS4-38294 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Galindo Guerreros, Julio Cesar A1 - Niederleithinger, Ernst A1 - Mackens, S. A1 - Fechner, Th. T1 - Crosshole and downhole seismics: a new quality assurance tool for jet grout columns N2 - Sealing and strengthening of the subsoil by grout injection is a major issue in the field of geotechnical engineering. One commonly applied method is jet grouting, which allows creating columns of grouted soil by eroding and mixing the in-situ soil with a thin cement suspension. A general difficulty linked with this method is in predicting the resulting column diameter and its material strength. In this paper, we illustrate the application of a newly developed non-destructive quality assurance tool used to determine the diameter of jet grout columns. This approach incorporates standard crosshole and downhole seismic measurements. To demonstrate its effectiveness, we tested the new approach within two-dimensional finite-difference numerical simulations. Additional field tests showed that this tool is also applicable in real site conditions. For this purpose, three jet grout columns were produced with different process parameters in a depth between 3 and 10 m. The evaluated diameters were within 1 and 1.5 m, slightly deviating from the previously predicted range by the jet grouting contractor. Moreover, we were able to detect the base of the columns at a 10-m depth with no significant difficulties. On the other hand, unsaturated, less compacted sands between the groundwater level and surface considerably affected the seismic data, hence complicating the detection of the top of the columns. KW - Jet grouting KW - Quality assurance PY - 2016 DO - https://doi.org/10.3997/1873-0604.2016042 SN - 1569-4445 IS - 14 SP - 493 EP - 501 PB - EAGE CY - Houton, NL AN - OPUS4-38977 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Progress in non-destructive testing and monitoring of concrete N2 - The presentation will give an overview on non-destructive testing techniques being developed at the Federal Institute for Materials Research and Testing, Germany (BAM). This includes ultrasonic methods, ground penetration radar, Laser-Induced Breakdown Spectroscopy (LIBS), infrared thermography, pile testing, sensor technology and building scanner. A focus of the talk will be ultrasonic methods, which are well established in various aspects of concrete testing. They are used for imaging the interior geometry of constructions, estimation of concrete strength or monitoring lab investigations. However, so far the detection of distributed damages, especially in an early stage, has been almost impossible. The arrival of new technologies as embedded transducers and sensitive data processing techniques adopted from seismology has opened new field of work. Recent research has been focused to detect changes in concrete elements induced by stress, temperature, moisture or chemical attacks by permanent monitoring. Techniques as Coda Wave Interferometry can resolve changes in ultrasonic velocity in the order of 1*10-5. In addition, many researchers believe that the investigation of nonlinear effects can be used to characterize damages. The presentation will give a wrap up of ultrasonic techniques currently used in practice. This will include echo based methods as multi-channel/multi-offset imaging of structural elements using commercial and prototype devices. Imaging methods as SAFT and RTM will be shortly discussed. The focus will be on the emerging techniques used for monitoring. New types of sensors will be presented as well as the devices used in laboratory and field applications. Insight will be given on the various influence factors on ultrasonic signals and various ways of feature extraction and data processing. The results of lab experiments will be shown to demonstrate the detection of various kind of damages from mechanical load, ASR, corrosion to fatigue. The experiences with our first installations in real constructions (bridges, tunnel) will also be presented. T2 - CIES Research Seminar, University of New South Wales CY - Sydney, Australia DA - 13.12.2016 KW - Ultrasound KW - Concrete KW - Monitoring KW - Imaging PY - 2016 AN - OPUS4-38731 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - State-of-the-art of ultrasonic monitoring of concrete N2 - Ultrasonic methods are well established in various aspects of concrete testing. They are used for imaging the interior geometry of constructions, estimation of concrete strength or monitoring lab investigations. However, so far the detection of distributed damages, especially in an early stage, has been almost impossible. The arrival of new technologies as embedded transducers and sensitive data processing techniques adopted from seismology has opened new field of work. Recent research has been focused to detect changes in concrete elements induced by stress, temperature, moisture or chemical attacks by permanent monitoring. Techniques as Coda Wave Interferometry can resolve changes in ultrasonic velocity in the order of 1*10-5. In addition, many researchers believe that the investigation of nonlinear effects can be used to characterize damages. The workshop will give a wrap up of ultrasonic techniques currently used in practice. This will include echo based methods as multi-channel/multi-offset imaging of structural elements using commercial and prototype devices. Imaging methods as SAFT and RTM will be shortly discussed. The focus will be on the emerging techniques used for monitoring. New types of sensors will be presented as well as the devices used in laboratory and field applications. Insight will be given on the various influence factors on ultrasonic signals and various ways of feature extraction and data processing. The results of lab experiments will be shown to demonstrate the detection of various kind of damages from mechanical load, ASR, corrosion to fatigue. The experiences with or first installations in real constructions (bridges, tunnel) will also be presented. T2 - The 8th Australian Network of Structural Monitoring Annual Workshop CY - Melbourne, Australia DA - 29.11.2016 KW - Ultrasound KW - Concrete KW - Monitoring KW - Imaging PY - 2016 AN - OPUS4-38727 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Niederleithinger, Ernst A1 - Abraham, O. A1 - Mooney, M. T1 - Special Issue on Geophysics for Non-destructive Testing in Civil Engineering Foreword N2 - Foreword to a special issue of "Near Surface Geophysics" on the application of geophysical techniques to non-destructive testing in civil engineering KW - geophysics non-destructive testing PY - 2016 DO - https://doi.org/10.3997/1873-0604.2016043 SN - 1569-4445 VL - 14 IS - 6 SP - 479 EP - 480 PB - EAGE CY - Houton, NL AN - OPUS4-38984 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - König, Markus A1 - Grohmann, Maria A1 - Niederleithinger, Ernst T1 - Anwendung der Reverse-Time Migration auf Ultraschall-Echo-Daten zur Detektion von verdeckten Rissen in Betonkörpern N2 - Das Ultraschall-Echo-Verfahren ist eine wichtige Methode der zerstörungsfreien Prüfung (ZfP). Prüfaufgaben im Bauwesen beinhalten unter anderem die korrekte Dickenbestimmung von Konstruktionen, sowie die Lokalisierung von Einbauteilen und Fehlstellen. Das Abbildungsverfahren RTM (Reverse Time Migration) liefert oft bessere Bilder als konventionelle Verfahren. Die Datenaufnahme am Betonprobekörper erfolgte mit einem Scannersystem der BAM, bei dem jeweils ein Ultraschall-Prüfkopf als Sender bzw. Empfänger diente. Es wurden senkrecht zur Profilrichtung horizontal polarisierte Scherwellen genutzt. Die RTM wurde mit dem Softwarepaket Madagascar gerechnet. Die Ergebnis zeigt das Potential dieser Methode im Bezug auf komplexe Strukturen. Die lateralen Positionen der Risse im RTM-Bild sowie deren Höhe innerhalb des Probekörpers, entsprechen recht genau dem visuellen Befund. T2 - 77. Jahrestagung der Deutschen Geophysikalischen Gesellschaft CY - Potsdam, Germany DA - 27.03.2017 KW - Ultraschall KW - Beton KW - Riss KW - Reverse Time Migration PY - 2017 AN - OPUS4-39662 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Grohmann, Maria A1 - Maack, Stefan A1 - Behrens, Matthias A1 - Niederleithinger, Ernst T1 - Low-frequency ultrasonic pulse-echo datasets for geometry determination of a reinforced concrete step specimen with embedded polystyrene foam cuboids in non-destructive testing N2 - The dataset comprises raw data collected using the ultrasonic pulse-echo method on a concrete specimen. The specimen addresses two fundamental non-destructive testing (NDT) challenges in civil engineering: locating built-in elements and determining dimensions to analyse both the internal and external geometry of concrete structures. For data acquisition, the surface of the concrete specimen was automatically scanned point by point, with pulse-echo measurements performed at each measuring point. The automation of the measurement process ensured high repeatability and precision as well as a high measurement point density. Two low-frequency probes were used, each capable of both transmitting and receiving ultrasonic waves: one for longitudinal waves and one for shear waves. The longitudinal wave probe operates at frequencies of up to approximately 160 kHz, whereby a frequency of 80 kHz was used for the ultrasonic measurements here. The shear wave probe operates at up to 100 kHz, with a frequency of 50 kHz used for the measurements in this study. This article includes additional technical specifications of the two ultrasonic probes used, as well as information on their geometric specifications and directivity patterns. It also provides a detailed description of the further measurement equipment used. The ultrasonic raw data are stored in a universally readable format, with each time signal (A-scan) spanning two milliseconds and a sampling rate of two mega-samples per second. The provided data support comparative studies in signal analysis, imaging as well as interpretation and can be used for evaluation purposes in various practical NDT scenarios. KW - Civil engineering KW - Concrete structures KW - Ultrasonic echo testing KW - Reference data PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639100 DO - https://doi.org/10.1016/j.dib.2025.111956 SN - 2352-3409 VL - 62 SP - 1 EP - 19 PB - Elsevier Inc. AN - OPUS4-63910 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Liao, Chun-Man A1 - Niederleithinger, Ernst A1 - Bernauer, F A1 - Igel, H A1 - Hadziioannou, Céline T1 - Wave-Screening Methods for Prestress-Loss Assessment of a Large-Scale Post-Tensioned Concrete Bridge Model Under Outdoor Conditions N2 - This paper presents advancements in structural health monitoring (SHM) techniques, with a particular focus on wave-screening methods for assessing prestress loss in a large-scale prestressed concrete (PC) bridge model under outdoor conditions. The wave-screening process utilizes low-frequency wave propagation obtained from seismic interferometry of structural free vibrations and high-frequency wave propagation obtained through ultrasonic transducers embedded in the structure. An adjustable post-tensioning system was employed in a series of experiments to simulate prestress loss. By comparing bridge vibrations under varying post-tensioning forces, the study investigated prestress loss and examined temperature-related effects using the coda wave interferometry (CWI) method. Local structural alterations were analyzed through wave velocity variations, demonstrating sensitivity to bridge temperature changes. The findings indicate that wave-based methods are more effective than traditional modal analysis for damage detection, highlighting the dual impacts of prestress loss and temperature, as well as damage localization. This study underscores the need for long-term measurements to account for temperature fluctuations when analyzing vibration measurements to investigate changes in prestressing force in PC structures. KW - Coda wave interferometry KW - Damage detection KW - Prestress loss KW - Seismic interferometry KW - SHM KW - Temperature influence KW - Ultrasonics KW - Wave-screening PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634244 UR - https://www.mdpi.com/2076-3417/15/11/6005 DO - https://doi.org/10.3390/app15116005 VL - 15 IS - 11 SP - 1 EP - 18 PB - MDPI AN - OPUS4-63424 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epple, Niklas A1 - Sanchez Trujillo, Camila A1 - Fontoura Barroso, Daniel A1 - Hau, Julia A1 - Niederleithinger, Ernst ED - Lienhart, Werner ED - Krüger, Markus T1 - Monitoring of Concrete Infrastructure with Active Ultrasound Coda Wave Interferometry N2 - Coda Wave Interferometry has been used in Geophysics to detect weak changes in scattering media. Past research in Structural Health Monitoring has shown that this methodology can be applied to concrete structures to detect material changes by calculation of relative velocity changes. Successive measurements with embedded ultrasonic transducers provide a repeatable signal for reliable long-term monitoring of concrete. To research the application in real-world structures, we have embedded ultrasonic transducers in a bridge in Ulm and a Metro station in Munich, Germany. This study gives an overview of the monitoring of these two structures. The results show the potential and challenges of the method. Data evaluation can be largely automated to gain insights into material changes and other influences on the structure, such as traffic-induced load and temperature variations. The experiments demonstrate the ease of installation, longevity of the sensor installation, and sensitivity of the measurement technique, but highlight problems with the application, especially if electromagnetic noise affects data quality. As no confirmed substantial damage was recorded during the monitoring period on both structures, we evaluate load tests to investigate the effect of static load on the structures and the coda monitoring results. The experiments show that the influence of load can be detected, even if the temperature influence is not removed from the data. This indicates that online damage detection with coda monitoring is possible, but further research on damage detection in real-world structures has to be conducted to confirm laboratory findings. T2 - 13th International Conference on Structural Health Monitoring of Intelligent Infrastructure CY - Graz, Austria DA - 01.09.2025 KW - Active Ultrasound Measurements KW - Coda Wave Monitoring KW - Embedded Transducers PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-640582 DO - https://doi.org/10.3217/978-3-99161-057-1-012 SP - 45 EP - 51 PB - Technische Universität Graz CY - Graz AN - OPUS4-64058 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vössing, Konrad A1 - Gaal, Mate A1 - Niederleithinger, Ernst T1 - Imaging wood defects using air coupled ferroelectret ultrasonic transducers in reflection mode N2 - Air-coupled ultrasound (ACU) is used to detect defects in wood panels without physically contacting the sample and with a quick scanning rate. Transducers made of cellular polypropylene (PP) with a high signal-to-noise ratio are quite suitable for ACU testing of wood. The extremely low modulus of elasticity and low density of PP transducers results in a small difference in acoustic impedance for the Transmission of ultrasonic waves between the transducer and air, allowing new areas of application to become possible. To demonstrate the suitability of the reflection technique, measurements are shown on the three samples Multiplex, LVL, and MDF and compared with transmission measurements. Due to this acoustic barrier and the use of cellular PP transducers, an exact detection of delamination and cavities is possible in wood panels up to 40 mm thick. If only one side of an object is accessible and the depth of the defect is of interest, the reflection technique is preferred at the expense of a reduced measuring accuracy and Penetration depth. KW - Wood KW - Ultrasound KW - Air coupled KW - Defects PY - 2020 DO - https://doi.org/10.1016/j.conbuildmat.2020.118032 VL - 241 SP - 118032, 1 EP - 8 PB - Elsevier Ltd. AN - OPUS4-50235 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Epple, Niklas A1 - Fontoura Barroso, Daniel A1 - Niederleithinger, Ernst ED - Rizzo, P. ED - Milazzo, A. T1 - Towards Monitoring of Concrete Structures with Embedded Ultrasound Sensors and Coda Waves – First Results of DFG for CoDA N2 - Due to the importance of reinforced concrete structures for modern society, damage assessment during the entire life-cycle of such structures has become a special interest in non-destructive testing. Using embedded ultrasound sensors in combination with other measurement methods, numerical modeling and self-made data collectors, tailored specifically for monitoring tasks, the German research group DFG FOR CoDA aims to investigate and develop novel methods for damage detection and rapid model updating in reinforced concrete structures. In the first stage of the project, besides the development of custom-built, low-cost data collectors, ultrasonic transducers are embedded in a large, reinforced concrete specimen on a BAM test site near Berlin. In this experiment, the influence of changing environmental conditions (mainly temperature) on the ultrasound signal is investigated using coda-wave interferometry. The results show a correlation between changes in temperature and ultrasonic velocity. Such changes must be taken into consideration in a long-term monitoring setup to distinguish between reversible and permanent changes. By correcting the data using a linear relation between concrete temperature and velocity change to remove the seasonal trends and by low-pass filtering the data to remove daily variations can remove most of the temperature influence on the ultrasound measurements. KW - Ultrasound KW - Coda Wave Interferometry (CWI) KW - Embedded sensors KW - Structural health monitoring PY - 2021 SN - 978-3-030-64593-9 SN - 978-3-030-64594-6 DO - https://doi.org/10.1007/978-3-030-64594-6_27 VL - 127 SP - 266 EP - 275 PB - Springer Nature CY - Cham, Switzerland AN - OPUS4-52012 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Wiggenhauser, Herbert A1 - Helmerich, Rosemarie A1 - Krause, Martin A1 - Mielentz, Frank A1 - Niederleithinger, Ernst A1 - Taffe, Alexander A1 - Wilsch, Gerd ED - Naus, D. T1 - Non-destructive Testing of Nuclear Power Plant Concrete Structures State of the Art Report N2 - Nuclear Power Plants have been in operation for ca. 50 years. Based on this experience, non-destructive testing tasks specific to thick and highly reinforced nuclear containment structures have materialized. The performance based Service life extension of existing NPPs also needs a measurement based decision to support continuing the service of the concrete part of the installations. By nature, concrete is a very durable material and any natural Deterioration processes may take a long time to become critical to the structure. The experience of more than 50 years of service limits the testing tasks to a few ones which are not yet solved. Research in NDT of concrete structures is performed by many research institutions all over the world with different technical and systematic approaches. Results are mainly obtained on laboratory specimens, sometimes additional field studies are reported. This research takes place independently without coordination and as a result, the outcomes mostly lack full comparability. Software for data analysis has become indispensable and very powerful. This part of testing needs more attention when it comes to evaluate test results. Validation of NDE solutions is becoming a critical part in concrete structure testing. Validation is by definition the proof that a customer´s requirements in the test are being met by the testing solution. This includes equipment, personnel qualification and data analysis. In the following tables, the research recommendation Validation is used in the sense, that proof of the performance of existing solutions needs to be adressed. In general, a validation methodology for NDE solutions for concrete testing in itself needs to be researched and established. Comparability of research also needs an accepted and easily accessible reference. From experience, it is almost impossible to manufacture exact copies of test specimens at different locations. Round Robin tests are therefore needed to evaluate the performance of a test. Data evaluation is generally done using dedicated software, sometimes Hardware dependant and not interchangeable between systems. Software is ever more increasingly becoming more powerful and sophisticated. An in-depth evaluation needs to address the comparability and validation of Software used for data analysis and evaluation. The vision of a unified software pool for NDE investigations would undoubtedly support research tremendously. Quantitative NDE is mostly recommended to assess the condition of a structure. However, qualitative data can be very useful, especially for processes which change the material properties or deteriorate the structure (e.g. corrosion of reinforcement). The need for reliable baseline data is a key factor for such monitoring tasks. KW - Nuclear structures KW - Non-destructive testing KW - State of the art KW - Research needs PY - 2013 SP - 1 EP - 120 PB - BAM CY - Berlin AN - OPUS4-51049 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst A1 - Epple, Niklas A1 - Fontoura Barroso, Daniel A1 - Clauß, F. A1 - Ahrens, M. A. A1 - Mark, P. ED - Krieger, J. ED - Isecke, B. T1 - Ultraschallbasierte Überwachung von Stahl- und Spannbeton-konstruktionen – erste Ergebnisse der DFG-Forschungsgruppe 2825 CoDA N2 - Die Überwachung von Bauteilen aus Stahl- oder Spannbeton mit Ultraschall hat in Labor- und Technikumsversuchen schon vielversprechende Ergebnisse gezeigt. Besonders gute Resultate wurden dabei mit eingebetteten Ultraschalltrans-ducern und bei Auswertung der Daten mit der hochsensiblen Codawelleninterferometrie erzielt. Erfasst werden können neben Temperatur- und Feuchteeffekten auch Belastungszustände und jegliche Art von Schädigung, die mit Mikro- oder Makrorissbildung einhergeht. Seit 2019 untersucht die DFG-Forschergruppe 2825 „CoDA“ (Sprecher: Prof. Christoph Gehlen, TU München) ver-schiedenste Aspekte dieser innovativen Technologie mit dem Ziel, Einflussgrößen quantitativ zu erfassen, Umweltein-flüsse zu korrigieren und 3D-Auswerteverfahren zu verbessern. Final soll eine am Bauwerk einsatzfähige Methode ent-stehen, die klassische Monitoringverfahren ergänzt und erweitert sowie Input zu einem Update des statischen Systems liefert. Aufgaben der BAM in der Forschergruppe ist neben Verbesserung und Adaptierung der Messsystem und Sensorik auch Langzeitversuche an einem Großobjekt und Testinstallationen an Realbauwerken. Hierzu liegen erste Ergebnisse vor, die zeigen, dass die Technologie auch außerhalb des Labors einsatzfähig ist. T2 - 4. Brückenkolloquium CY - Online meeting DA - 08.09.2020 KW - Brücke KW - Monitoring KW - Ultraschall KW - Codawelleninterferometrie PY - 2020 SN - 978-3-8169-3518-6 SP - 473 EP - 480 PB - expert CY - Tübingen AN - OPUS4-51205 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Ultraschallbasierte Überwachung von Stahl- und Spannbeton-konstruktionen – erste Ergebnisse der DFG-Forschungsgruppe 2825 CoDA N2 - Die Überwachung von Bauteilen aus Stahl- oder Spannbeton mit Ultraschall hat in Labor- und Technikumsversuchen schon vielversprechende Ergebnisse gezeigt. Besonders gute Resultate wurden dabei mit eingebetteten Ultraschalltrans-ducern und bei Auswertung der Daten mit der hochsensiblen Codawelleninterferometrie erzielt. Erfasst werden können neben Temperatur- und Feuchteeffekten auch Belastungszustände und jegliche Art von Schädigung, die mit Mikro- oder Makrorissbildung einhergeht. Seit 2019 untersucht die DFG-Forschergruppe 2825 „CoDA“ (Sprecher: Prof. Christoph Gehlen, TU München) ver-schiedenste Aspekte dieser innovativen Technologie mit dem Ziel, Einflussgrößen quantitativ zu erfassen, Umweltein-flüsse zu korrigieren und 3D-Auswerteverfahren zu verbessern. Final soll eine am Bauwerk einsatzfähige Methode ent-stehen, die klassische Monitoringverfahren ergänzt und erweitert sowie Input zu einem Update des statischen Systems liefert. Aufgaben der BAM in der Forschergruppe ist neben Verbesserung und Adaptierung der Messsystem und Sensorik auch Langzeitversuche an einem Großobjekt und Testinstallationen an Realbauwerken. Hierzu liegen erste Ergebnisse vor, die zeigen, dass die Technologie auch außerhalb des Labors einsatzfähig ist. T2 - 4. Brückenkolloquium CY - Online meeting DA - 08.09.2020 KW - Ultraschall KW - Monitoring KW - Brücke KW - Codawelleninterferometrie PY - 2020 AN - OPUS4-51206 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epple, Niklas T1 - Monitoring of Concrete with Embedded Ultrasound Sensors, Coda Waves and a Novel Measurement Device N2 - Using embedded ultrasound (US) sensors in civil engineering structures and Coda Wave Interferometry (CWI), DFG research group CoDA aims for developing methods of concrete damage assessment by combination of Micro and macro scale simulations and experiments. BAMs goal within the project is the provision of small and durable measurement equipment on the one hand, and the investigation of damage sensitive parameters and development of an imaging algorithm on the other hand. In this study we focus on the development of the measurement system and the influence of temperature variations on the measurements. T2 - Summer School DFG FOR CoDA CY - Berchtesgaden, Germany DA - 27.09.2020 KW - Ultrasound KW - Coda Wave Interferometry KW - Structural Health Monitoring PY - 2020 AN - OPUS4-51382 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -