TY - JOUR A1 - Zhang, K. A1 - Mezhov, Alexander A1 - Schmidt, Wolfram T1 - Effect of Polycarboxylate Superplasticizer in Ordinary Portland Cement and Sulfate Resistant Cement N2 - Polycarboxylate superplasticizers (PCE) are the most widely used admixtures in today’s cementitious construction materials. The molecular structure has a decisive influence on the effectiveness of PCE, which also can be tailored to serve in a different cementitious system. The current study investigates the influence of the backbone charge density of PCE on the rheology, hydration kinetics, and adsorption behavior of ordinary Portland cement (OPC) and sulfate-resistant cement (SRC). The results indicate that regardless of the PCE type, OPC requires a higher amount of PCE to be adsorbed to induce changing of rheological parameters and hydration kinetics. Regardless of the cement type, the PCE with a higher charge density exhibits higher adsorption behavior, corresponding to lower viscosity measurement. Compared to OPC, SRC is more sensitive to the introduction of both PCEs and has a lower saturation dosage, indicating that SRC generally provides better workability properties regardless of the PCE. KW - Polycarboxylate superplasticizers (PCE) KW - Sulfate resistant cement (SRC) KW - Rheological KW - Adsorption KW - Cement hydration PY - 2023 DO - https://doi.org/10.1061/JMCEE7.MTENG-15033 SN - 0899-1561 VL - 35 IS - 6 SP - 1 EP - 12 PB - ASCE Libary AN - OPUS4-58244 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zekhnini, Khalid A1 - Ebell, Gino T1 - Corrosion behavior of simulated monopile foundation by S355J2 steel in artificial seawater and sediment N2 - The development of offshore wind turbines (WTGs) presents many challenges in terms of safe operation over extended periods of time. One of these is the corrosive environment towards metallic materials, which can lead to a loss of material thickness and thus to a deterioration of mechanical performances, especially the strength of infrastructures. This can be counteracted by painting and cathodic protection (CP). Much research has already been done in this area about inhibiting the corrosion process. However, gaps exist regarding free corrosion. This plays a greater role especially for time intervals during the installation of the systems and their maintenance, during which often no CP can be operated. This is especially true for areas where painting surfaces is impossible e.g., sediment areas. This problem is exacerbated by the different corrosion rates caused by the different zones (water and sediment), with their different amounts of dissolved oxygen. This presentation deals with experiments in artificial seawater and sediment. Classical S355J2 steel samples in the form of coupons were fitted with welding wires that carried out the electrical contact to the outer side of the basin. Inside the basins, the specimens are stored in different zones like water and sediment which should simulate the foundation situation of monopiles. The mass loss was determined gravimetrically, elemental currents between specimens in water and sediment were measured and electrochemical investigations were carried out. The influences of the zones, based on different solved oxygen contents, and the rolling skin towards the corrosion behavior of the mild steel samples were determined in this work. Especially the influence of the sediment showed unexpected behavior, determined by electrochemical investigations. These results allow better conclusions to be drawn about the corrosion behavior of low alloy steels in offshore environments used in sediment and seawater, which cannot always be protected. T2 - Eurocorr 2023 CY - Brussels, Belgium DA - 28.08.2023 KW - Marine Corrosion KW - Offshore KW - Monopile KW - Sediment KW - Artificial seawater PY - 2023 AN - OPUS4-58175 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zekhnini, Khalid A1 - Ebell, Gino A1 - Burkert, Andreas T1 - Corrosion at metallic offshore constructions – Bundesanstalt für Materialforschung und -prüfung (BAM) N2 - In the maritime context of offshore operation, corrosion, in combination with the materials used, poses a particular challenge to ensure safe operation over long indefinite periods and to minimise susceptibility to failure. Until today, only a few corrosion protection systems have proven themselves for the interaction of efficiency, installation, and maintenance in the offshore sector. In addition, available corrosion test methods sometimes have major deficits about conclusions of the durability. Therefore, there is more research and development needed. The flagship project H2Mare of the Federal Ministry of Education and Research aims to enable the production of green hydrogen and PtX products at high seas. Research is being driven forward by the partners in four individual projects, where BAM is involved in two. In PtX-Wind, major kinds of corrosion attacks at offshore constructions are characterized and investigated, and suitable corrosion protection measures determined. In TransferWind, attention focusses on transferring scientific results into standardization. This poster at the H2Mare Conference 2023 presents an overview of the investigation methods and contribution of the department “Corrosion and Corrosion Protection”. T2 - H2Mare Conference 2023 CY - Frankfurt/Main, Germany DA - 12.06.2023 KW - Atmospheric Corrosion KW - Sea Water KW - Corrosion Testing KW - Offshore KW - Laboratory Container KW - Corrosion protecting system PY - 2023 AN - OPUS4-57838 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Xu, R. A1 - Hicke, Konstantin A1 - Chruscicki, Sebastian A1 - Marx, S. ED - Curbach, M. ED - Marx, S. ED - Scheerer, S. ED - Hampel, T. T1 - Akustisches SpRK-Monitoring mit SEA und verteilten faseroptischen Sensoren N2 - Im vorliegenden Bericht wurde untersucht, Spanndrahtbrüche in einem Brückenträger sowohl mittels Schallemissionsanalyse (SEA) als auch mit (eingebetteter) verteilter faseroptischer akustischer Sensorik (DAS) zu erkennen. Die Ergebnisse zeigen, dass die Bruchsignale anhand beider Messverfahren detektiert werden können. Die jeweils detektierten Drahtbrüche werden miteinander verglichen. Durch eine Gegenüberstellung werden SEA und DAS detailliert dargestellt. T2 - 12. Symposium "Experimentelle Untersuchungen von Baukonstruktionen" (SEUB) CY - Dresden, Germany DA - 01.06.2023 KW - Verteilte faseroptische akustische Sensorik KW - DAS KW - Brückenmonitoring KW - Spanndrahtbruchdetektion KW - Schallemissionsanalyse KW - SEA PY - 2023 SN - 978-3-86780-740-1 SN - 1613-6934 VL - 67 SP - 136 EP - 147 PB - Technische Universität Dresden - Fakultät Bauingenieurwesen CY - Dresden AN - OPUS4-57581 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wu, Hongyi A1 - Christiani, Ricardo A1 - Hofmann-Böllinghaus, Anja T1 - Untersuchung von Brandausbreitungsmechanismen bei Waldbränden N2 - Das EU Projekt TREEADS „A Holistic Fire Management Ecosystem for Prevention, Detection and Restoration of Environmental Desasters” beschäftigt sich mit der Erforschung der drei Phasen „Prävention und Bereitschaft“, „Detektion und Reaktion“ und „Aufforsten und Anpassen“ der Waldbrandverhütung. Im Projekt gibt es acht ausgewiesene Pilotregionen, in denen Deutschland auch mit einer Pilotregion in Sachsen-Anhalt bzw. in Brandenburg vertreten ist. Unsere Arbeit auf Charakterisierung des Waldbodens und numerische Simulation wird vorgestellt. T2 - vfdb-Jahresfachtagung 2023 CY - Münster, Germany DA - 15.05.2023 KW - Waldbrand KW - Klimawandel KW - Charakterisierung des Waldbodens KW - Numerische Strömungsmechanik PY - 2023 AN - OPUS4-57621 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wu, Dejian A1 - Zhao, P. A1 - Spitzer, Stefan A1 - Krietsch, Arne A1 - Amyotte, P. A1 - Krause, U. T1 - A review on hybrid mixture explosions: Safety parameters, explosion regimes and criteria, flame characteristics N2 - The hybrid mixture of combustible dusts and flammable gases/vapours widely exist in various industries, including mining, petrochemical, metallurgical, textile and pharmaceutical. It may pose a higher explosion risk than gas/vapor or dust/mist explosions since the hybrid explosions can still be initiated even though both the gas and the dust concentration are lower than their lower explosion limit (LEL) values. Understanding the explosion threat of hybrid mixtures not only contributes to the inherent safety and sustainability of industrial process design, but promotes the efficiency of loss prevention and mitigation. To date, however, there is no test standard with reliable explosion criteria available to determine the safety parameters of all types of hybrid mixture explosions, nor the flame propagation and quenching mechanism or theoretical explanation behind these parameters. This review presents a state-of-the-art overview of the comprehensive understanding of hybrid mixture explosions mainly in an experimental study level; thereby, the main limitations and challenges to be faced are explored. The discussed main contents include the experimental measurement for the safety parameters of hybrid mixtures (i.e., explosion sensitivity and severity parameters) via typical test apparatuses, explosion regime and criterion of hybrid mixtures, the detailed flame propagation/quenching characteristics behind the explosion severities/sensitivities of hybrid mixtures. This work aims to summarize the essential basics of experimental studies, and to provide the perspectives based on the current research gaps to understand the explosion hazards of hybrid mixtures in-depth. KW - Hybrid mixtures KW - Explosion protection KW - Safety characteristics PY - 2023 DO - https://doi.org/10.1016/j.jlp.2022.104969 SN - 0950-4230 VL - 82 SP - 1 EP - 54 PB - Elsevier CY - Amsterdam AN - OPUS4-56856 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander A1 - Königsbauer, Korbinian A1 - Krebber, Katerina A1 - Schaller, M.B. A1 - Färber, J. A1 - Nöther, N. T1 - POF-based monitoring system using digital I-OFDR for strain detection in road construction N2 - We present a prototype of a distributed POF sensing system for strain detection in road construction and civil engineering ready to be used in practical applications. The system is based on a cost-efficient digital incoherent optical frequency domain reflectometry (I-OFDR). In this approach, the strain-induced changes in the Rayleigh backscattering profile along a perfluorinated polymer optical fiber (PF-POF) are determined by measuring the complex transfer function of the sensing fiber using a compact digital data acquisition unit. The digital unit replaces an oversized vector network analyzer (VNA) enabling suitability of the measurement system for out-door use and providing a significant reduction of the total system costs at the same time. The entire sensor con-cept includes the use of geosynthetics with integrated PF-POFs as two-dimensional sensor structures for geotech-nical applications. The robustness and the functionality of the distributed POF I-OFDR sensors were proven in the field. The field test involved embedding of two geomats, each with two polymer optical sensor loops, into the embankment of the federal road B 91 in a section near Leipzig. The measurements conducted after the sensor-based geomats had been installed confirmed both the potential of such smart geosynthetics and the functionali-ty of the digital I-OFDR prototype. T2 - POF2023 CY - Cork, Irland DA - 17.09.2023 KW - Digital I-OFDR KW - Distriubuted polymer optical fiber sensor KW - Smart geosynthetics KW - Strain detection KW - Structural health monitoring PY - 2023 AN - OPUS4-58423 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Winkler, Nicolas P. A1 - Johann, Sergej A1 - Kohlhoff, Harald A1 - Neumann, Patrick P. T1 - Revisiting Environmental Sensing Nodes: Lessons Learned and Way Forward N2 - Setting up sensors for the purpose of environmental monitoring should be a matter of days, but often drags over weeks or even months, preventing scientists from doing real research. Additionally, the newly developed hardware and software solutions are often reinventing existing wheels. In this short paper, we revisit the design of our environmental sensing node that has been monitoring industrial areas over a span of two years. We share our findings and lessons learned. Based on this, we outline how a new generation of sensing node(s) can look like. T2 - SMSI 2023 Conference Sensor and Measurement Science International CY - Nuremberg, Germany DA - 08.05.2023 KW - Sensing node KW - Sensor network KW - Environmental monitoring KW - Low-cost KW - LoRaWAN PY - 2023 SN - 978-3-9819376-8-8 DO - https://doi.org/10.5162/SMSI2023/C5.1 SP - 173 EP - 174 PB - AMA Service GmbH CY - Wunstorf AN - OPUS4-57454 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Winkler, Nicolas P. A1 - Johann, Sergej A1 - Kohlhoff, Harald A1 - Neumann, Patrick P. T1 - Revisiting Environmental Sensing Nodes: Lessons Learned and Way Forward N2 - Setting up sensors for the purpose of environmental monitoring should be a matter of days, but often drags over weeks or even months, preventing scientists from doing real research. Additionally, the newly developed hardware and software solutions are often reinventing existing wheels. In this short paper, we revisit the design of our environmental sensing node that has been monitoring industrial areas over a span of two years. We share our findings and lessons learned. Based on this, we outline how a new generation of sensing node(s) can look like. T2 - SMSI 2023 Conference Sensor and Measurement Science International CY - Nuremberg, Germany DA - 08.05.2023 KW - Sensing node KW - Sensor network KW - Environmental monitoring KW - Low-cost KW - LoRaWAN PY - 2023 AN - OPUS4-57455 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wilrich, Cordula A1 - Wilrich, T. T1 - Nachbarklage gegen einen Sauerstofftank N2 - Technische Regeln im Arbeitsschutz – wie TRBS für die Betriebssicherheitsverordnung und TRGS für die Gefahrstoffverordnung – sind nicht zwingendes Recht, sondern konkretisierende Empfehlungen mit Vermutungswirkung. In Gerichtsurteilen werden sie eher selten herangezogen. Wie diese – und Branchenregelungen von Verbänden – von der Rechtsprechung diskutiert werden, zeigt ein Urteil des Verwaltungsgerichts Münster. KW - Arbeitsschutz KW - Gefahrstoffverordnung KW - Betriebssicherheitsverordnung KW - TRGS KW - TRBS KW - Sauerstofftank KW - Branchenregelung KW - Nachbarklage KW - Sicherheitsabstand PY - 2023 UR - https://sisdigital.de/ce/nachbarklage-gegen-einen-sauerstofftank/detail.html SN - 2199-7330 SN - 2199-7349 (eJournal) IS - 11 SP - 513 EP - 516 PB - Erich Schmidt Verlag (ESV) CY - Berlin AN - OPUS4-58773 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilrich, Cordula T1 - Lagerung von Gefahrstoffen gemäß TRGS 510 N2 - Der Vortrag stellt die wesentlichen Inhalte sowie die wichtigsten Änderungen der TRGS 510 "Lagerung von Gefahrstoffen in ortsbeweglichen Behältern" vor. Die TRGS 510 zeichnet sich durch ein gestuftes Maßnahmenkonzept in Abhängigkeit von der Art und Menge der gelagerten Gefahrstoffe aus. Folgende Maßnahmenstufen werden durch die TRGS 510 beschrieben: 1. Kleinmengen -> Allgemeine Maßnahmen 2. Überschreitung der Kleinmengen -> Lagerung im Lager 3. Überschreitung bestimmter Mengen für spezielle Gefahrstoffe -> Spezielle Maßnahmen 4. Verschiedene Gefahrstoffe und Lagerung im Lager erforderlich -> ggf. Getrenntlagerung und Separatlagerung T2 - Schulungsveranstaltung der Länder für den Vollzug / die Gewerbeaufsicht CY - Online meeting DA - 07.02.2023 KW - Gefahrstoffe KW - Lagerung KW - Technische Regeln für Gefahrstoffe KW - Gefahrstoffverordnung KW - TRGS PY - 2023 AN - OPUS4-56967 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weise, Frank A1 - Fladt, Matthias T1 - Innenhydrophobierung von Fahrbahndeckenbetonen als AKR-Vermeidungsstrategie N2 - An den vor allem vor 2006 errichteten Betonfahrbahndecken sind in den letzten Jahren vermehrt AKR-Schäden aufgetreten. Vor diesem Hintergrund wurde durch das BMVBS das ARS 04/2013 erlassen. Dieses wiederum sieht verbindlich im Vorfeld des Neubaus und der Erneuerung von Fahrbahndecken aus Beton im deutschen Bundesautobahnnetz einen Eignungsnachweis für die Gesteinskörnungen vor. Das hatte in den Folgejahren eine drastische Reduzierung der einsatzbaren Gesteinskörnungen zur Folge. Vor diesem Hintergrund wird in dem Beitrag die Leistungsfähigkeit der Innenhydrophobierung als neuartige AKR-Vermeidungsstrategie zur Nutzbarmachung grenzwertig alkaliempfindlicher Gesteinskörnungen aufgezeigt. Dabei wird ein Einblick in die Ergebnisse zweier aufeinander aufbauender BASt-Forschungsvorhaben gegeben. Den Schwerpunkt bildet hierbei die Bewertung des Einflusses der Dosierung des Hydrophobierungsmittels auf die Frisch- und Festbetoneigenschaften im Rahmen von Basisuntersuchungen im Labor. Aufbauend darauf wird das Prüfprogramm eines großmaßstäblichen Technikumsversuchs und der aktuelle Stand der Umsetzung aufgezeigt. T2 - 4. Forschungskolloquium Betonstraßenbau CY - Dresden, Germany DA - 19.01.2023 KW - Alkali-Kieselsäure-Reaktion KW - Betonfahrbahndecke KW - AKR-Vermeidung KW - Innenhydrophobierung PY - 2023 AN - OPUS4-56869 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weise, Frank A1 - Fladt, Matthias T1 - Bewertung der Innenhydrophobierung als neuartige AKR-Vermeidungsstrategie bei Betonfahrbahndecken N2 - Zur Vermeidung von AKR-Schäden an Betonfahrbahndecken im deutschen Autobahnnetz wurden mit dem ARS 04/2013 verbindliche Eignungsprüfungen zum Ausschluss alkaliempfindlicher Gesteinskörnungen bei Neubau- und Erhaltungsmaßnahmen eingeführt. Das hatte eine signifikante Reduzierung geeigneter Gesteinskörnungen zur Folge. Deshalb wird geprüft, ob durch die Zugabe eines Hydrophobierungsmittels während der Betonherstellung grenzwertig alkaliempfindliche Gesteinskörnungen nutzbar gemacht werden können. In diesem Beitrag wird der Einfluss der Dosierung eines Compounds mit Hydrophobierungsmittel (HM) auf die Frisch- und Festbetoneigenschaften eines Waschbetons mit einer reaktiven Grauwacke dargestellt. Es zeigt sich, dass aufgrund des Antagonismus die zunehmende Dosierung des HM-Compounds eine signifikante Erhöhung der Zugabe des Luftporenbildners auf Wurzelharzbasis erfordert. Der AKR-Schädigungsprozess wird ab einer Dosierung des HM-Compounds von 0,75 M.-%, bezogen auf den Zementgehalt, hinreichend vermindert. Die mechanischen Eigenschaften des hydrophobierten Waschbetons verschlechtern sich im betrachteten Dosierungsbereich des HM-Compounds nur geringfügig. Auch der Frost-Tausalz-Widerstand vermindert sich, ohne den normativen Grenzwert für die Abwitterung zu überschreiten. T2 - 21. Internationale Baustofftagung ibausil CY - Weimar DA - 13.09.2023 KW - Alkali-Kieselsäure-Reaktion KW - Betonfahrbahndecke KW - Innenhydrophobierung KW - AKR-Vermeidung PY - 2023 AN - OPUS4-58357 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weigel, Sandra A1 - Sielaff, S. A1 - Kunsic-Nowak, T. A1 - Nytus, N. A1 - Schwettmann, K. A1 - Schulze, C. A1 - Wetekam, J. T1 - Die FTIR-Untersuchung von Bitumen: Chancen, Durchführung und Präzision N2 - Die Fourier-Transformations-Infrarot-Spektroskopie (FTIR-Spektroskopie) stellt eine innovative und wirkungsvolle Methode zur Charakterisierung von Bitumen und bitumenhaltigen Bindemitteln dar. So erlaubt die FTIRCharakterisierung nicht nur eine Bewertung des Alterungsfortschritts eines Bindemittels, sondern zudem auch die Identifizierung von im Bitumen enthaltenen Additiven und Schadstoffen wie z. B. polyzyklischen aromatischen Kohlenwasserstoffen (PAK), die Ableitung verschiedener physikalischer und chemischer Kennwerte sowie weiterhin eine Klassifizierung von Bindemitteln nach verschiedenen übergeordneten Eigenschaften wie der Raffinerie, dem Alterungszustand und auch der Alterungsempfindlichkeit. KW - Bitumen und bitumenhaltige Bindemittel KW - FTIR-Spektroskopie KW - Anwendungsmöglichkeiten KW - Vergleichuntersuchung KW - Arbeitsanleitung KW - Präzision PY - 2023 UR - https://www.kirschbaum.de/fachzeitschriften/strasse-und-autobahn/strasse-und-autobahn/aktuelles-heft-17.html DO - https://doi.org/10.53184/STA8-2023-4 VL - 74/8 SP - 630 EP - 642 PB - KIRSCHBAUM VERLAG GmbH CY - Bonn AN - OPUS4-59049 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weigel, Sandra T1 - Estimating aging sensitivity of bitumen using FTIR spectroscopy and multivariate evaluation N2 - In this work, a methodology based on Fourier transform infrared (FTIR)spectroscopy and multivariate evaluation is presented to estimate the aging sensitivity of bitumen based on the unaged samples and thus without the need for time- and material-consuming aging simulations. For this purpose, factor analysis and linear discriminant analysis are used to develop a statistical model based on the FTIR spectra of unaged bitumen samples, which can be used fast and simple in everyday laboratory work and allows to assign the bitumen to a low, moderate, or strong aging sensitivity. The evaluation of the aging sensitivity is based on the complex shear modulus|G* | and the phase angle δ from the measurement with a dynamic shear rheometer(DSR), whose aging-related changes were captured as the slope in the Black diagram. A relevant influence on the classification concerning the aging sensitivity has the oxygen-containing compounds(sulfoxide, hydroxyl and partly carbonyl compounds), whereby lower contents and thus less preaged bitumen tend to have a stronger aging sensitivity. However, in addition to the oxygen-containing compounds, the structure of the aliphatic and aromatic compounds and, in particular, the interaction of the different structures are decisive for the aging sensitivity KW - Bitumen KW - Ageing behaviour KW - Characterisation KW - FTIR KW - Multivariate analysis methods PY - 2023 DO - https://doi.org/10.1088/2631-8695/acdce0 SN - 2631-8695 VL - 5 IS - 2 SP - 1 EP - 14 PB - IOP Publishing AN - OPUS4-58020 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vollpracht, A. A1 - Thiel, C. A1 - Zhao, Z. A1 - Villagrán Zaccardi, Y. A. A1 - Cordoba, G. P. A1 - Gluth, Gregor A1 - Vanoutrive, H. A1 - Gruyaert, E. A1 - Kanellopoulos, A. A1 - Mi, R. A1 - De Belie, N. T1 - Carbonation of concrete with SCMs: a data analysis by RILEM TC 281-CCC N2 - The RILEM TC 281–CCC "Carbonation of concrete with supplementary cementitious materials" is studying the effect of supplementary cementitious materials (SCMs) on natural and accelerated carbonation of blended cements. In this context a large database with carbonation depths over time has been set-up with currently 910 concrete and mortar mixes, which have been tested at different curing conditions. The collected data includes information on chemical composition and physical properties of the raw materials, on mix-design, compressive strength, curing and carbonation testing conditions. Data for a large variety of binders (with up to 94 % SCMs) and mix designs (with w/b ratios ranging from 0.26 to 0.75) were collected from the literature and unpublished material testing projects. Natural carbonation was recorded for several years in many cases, and indoor as well as outdoor results are included. However, in this contribution only lab conditions are considered. Carbonation kinetics are investigated considering the binder composition and mix design. Furthermore, the accuracy of accelerated carbonation testing is evaluated. As described in literature, the w/CaOreactive-ratio is a decisive factor for carbonation resistance but curing and exposure conditions influence the results as well. Even with identical test conditions, the scatter is very large. T2 - 16th International Congress on the Chemistry of Cement 2023 (ICCC2023) CY - Bangkok, Thailand DA - 18.09.2023 KW - Carbonation KW - Supplemetary cementitious materials KW - Blended cement KW - Concrete PY - 2023 UR - https://www.iccc-online.org/fileadmin/gruppen/iccc/proceedings/ICCC16_2023_Vol_III.pdf VL - III SP - 360 EP - 363 PB - Thailand Concrete Association AN - OPUS4-58736 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Unger, Jörg F. A1 - Robens-Radermacher, Annika A1 - Tamsen, Erik T1 - Data provenance - from experimental data to trustworthy simulation models and standards N2 - FAIR (findable, accessible, interoperable and reusable) data usage is one of the main principals that many of the research and funding organizations include in their strategic plans, which means that following the main principals of FAIR data is required in many research projects. The definition of data being FAIR is very general. When implementing that for a specific application or project or even setting a standardized procedure within a working group, a company or a research community, many challenges arise. In this contribution, an overview about our experience with different methods and tools is outlined. We begin with a motivation on potential use cases for the application of FAIR data with increasing complexity starting from a reproducible research paper over collaborative projects with multiple participants such as Round-Robin tests up to data-based models within standardization codes, applications in machine learning or parameter estimation of physics-based simulation models. In a second part, different options for structuring the data (including metadata schema) are discussed. The first one is the openBIS system, which is an open-source lab notebook and PostgreSQL based data management system. A second option is a semantic representation using RDF based on ontologies for the domain of interest. In a third section, requirements for workflow tools to automate data processing are discussed and their integration into reproducible data analysis is presented with an outlook on required information to be stored as metadata in the database. Finally, the presented procedures are exemplarily demonstrated for the calibration of a temperature dependent constitutive model for additively manufactured mortar. A metadata schema for a rheological measurement setup is derived and implemented in an openBIS database. After a short review of a potential numerical model predicting the structural build-up behavior, the automatic workflow to use the stored data for model parameter estimation is demonstrated. KW - FAIR data KW - Semantic web KW - Scientific workflows KW - Metadata KW - Reproducible data processing PY - 2023 DO - https://doi.org/10.1016/j.matpr.2023.08.081 SP - 1 EP - 10 PB - Elsevier AN - OPUS4-58215 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unger, Jörg F. A1 - Robens-Radermacher, Annika A1 - Tamsen, Erik T1 - Data provenance - from experimental data to trustworthy simulation models and standards N2 - FAIR (findable, accessible, interoperable and reusable) data usage is one of the main principals that many of the research and funding organizations include in their strategic plans, which means that following the main principals of FAIR data is required in many research projects. The definition of data being FAIR is very general, and when implementing that for a specific application or project or even setting a standardized procedure within a working group, a company or a research community, many challenges arise. In this contribution, an overview about our experience with different methods, tools and procedures is outlined. We begin with a motivation on potential use cases for the applications of FAIR data with increasing complexity starting from a reproducible research paper over collaborative projects with multiple participants such as Round-Robin tests up to data-based models within standardization codes, applications in machine learning or parameter estimation of physics-based simulation models. In a second part, different options for structuring the data are discussed. On the one hand, this includes a discussion on how to define actual data structures and in particular metadata schema, and on the other hand, two different systems for storing the data are discussed. The first one is the openBIS system, which is an open-source Lab notebook and PostgreSQL based data management system. A second option are a semantic representations using RDF based ontologies for the domain of interest. In a third section, requirements for workflow tools to automate data processing are discussed and their integration into reproducible data analysis is presented with an outlook on required information to be stored as metadata in the database. Finally, the presented procedures are exemplarily demonstrated for the calibration of a temperature dependent constitutive model for additively manufactured mortar. Metadata schemata for a rheological measurement setup are derived and implemented in an openBIS database. After a short review of a potential numerical model predicting the structural build-up behaviour, the automatic workflow to use the stored data for model parameter estimation is demonstrated. T2 - 4th International Congress on Materials & Structural Stability CY - Rabat, Morocco DA - 08.03.2023 KW - Data provenance KW - Experimental data to trustworthy KW - Simulation models and Standards PY - 2023 UR - https://www.rsc-cmss23.asmatec.org/RILEM%20Committees%20Program.php SP - 1 EP - 9 CY - Rabat, Morocco AN - OPUS4-57349 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unger, Jörg F. A1 - Robens-Radermacher, Annika T1 - A Database for Analyzing Round Robin Data N2 - FAIR (findable, accessible, interoperable and reusable) data usage is one of the main principals that many of the research and funding organizations include in their strategic plans, which means that following the main principals of FAIR data is required in many research projects. The definition of data being FAIR is very general, and when implementing that for a specific application or project or even setting a standardized procedure within a working group, a company or a research community, many challenges arise. In this contribution, an overview about our experience with different methods, tools and procedures is outlined. We begin with a motivation on potential use cases for the applications of FAIR data with increasing complexity starting from a reproducible research paper over collaborative projects with multiple participants such as Round-Robin tests up to data-based models within standardization codes, applications in machine learning or parameter estimation of physics-based simulation models. In a second part, different options for structuring the data are discussed. On the one hand, this includes a discussion on how to define actual data structures and in particular metadata schema, and on the other hand, two different systems for storing the data are discussed. The first one is the openBIS system, which is an open-source Lab notebook and PostgreSQL based data management system. A second option are a semantic representations using RDF based ontologies for the domain of interest. In a third section, requirements for workflow tools to automate data processing are discussed and their integration into reproducible data analysis is presented with an outlook on required information to be stored as metadata in the database. Finally, the presented procedures are exemplarily demonstrated for the calibration of a temperature dependent constitutive model for additively manufactured mortar. Metadata schemata for a rheological measurement setup are derived and implemented in an openBIS database. After a short review of a potential numerical model predicting the structural build-up behaviour, the automatic workflow to use the stored data for model parameter estimation is demonstrated. T2 - RILEM Spring Convention CY - Rabat, Morocco DA - 06.03.2023 KW - Database for Analyzing KW - Round Robin Data KW - Safety in technology and chemistry PY - 2023 AN - OPUS4-57348 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unger, Jörg F. A1 - Robens-Radermacher, Annika A1 - Tamsen, Erik T1 - Data provenance - from experimental data to trustworthy simulation models and standards N2 - Data provenance - from experimental data to trust worthy simulation models and standards Jörg F. Unger, Annika Robens-Radermacher, Erik Tamsen Bundesanstalt für Materialforschung und -prüfung (BAM). Unter den Eichen 87, 12205 Berlin, Germany FAIR (findable, accessible, interoperable and reusable) data usage is one of the main principals that many of the research and funding organizations include in their strategic plans, which means that following the main principals of FAIR data is required in many research projects. The definition of data being FAIR is very general, and when implementing that for a specific application or project or even setting a standardized procedure within a working group, a company or a research community, many challenges arise. In this contribution, an overview about our experience with different methods, tools and procedures is outlined. We begin with a motivation on potential use cases for the applications of FAIR data with increasing complexity starting from a reproducible research paper over collaborative projects with multiple participants such as Round-Robin tests up to data-based models within standardization codes, applications in machine learning or parameter estimation of physics-based simulation models. In a second part, different options for structuring the data are discussed. On the one hand, this includes a discussion on how to define actual data structures and in particular metadata schema, and on the other hand, two different systems for storing the data are discussed. The first one is the open BIS system, which is an opensource Lab notebook and Postgre SQL based data management system. A second option are a semantic representations using RDF based ontologies for the domain of interest. In a third section, requirements for workflow tools to automate data processing are discussed and their integration into reproducible data analysis is presented with an outlook on required information to be stored as metadata in the database. T2 - 4th International Congress on Materials & Structural Stability CY - Rabat, Morocco DA - 08.03.2023 KW - Data provenance KW - Experimental data to trustworthy KW - Simulation models and Standards PY - 2023 AN - OPUS4-57333 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Turski Silva Diniz, Analice A1 - Marti, J. M. A1 - Schartel, Bernhard T1 - High Heat Resistance Can Be Deceiving: Dripping Behavior of Polyamide 4.6 in Fire N2 - Polyamide 4.6 (PA46) is a high-heat-resistant polymer, but it has no dripping resistance under fire. Three commercial grades of PA46 are investigated under UL 94 vertical fire test conditions. Their performances are discussed based on the materials’ structural, thermal, and rheological properties. PA46 presents flaming drops, whereas dripping is prevented in the flame-retarded PA46. Friction-modified PA46 has increased flaming dripping. Temperature profiles of the specimens under fire and the temperature of the drops are measured by thermocouples. A UL 94 vertical test configuration consisting of two flame applications is designed to assess the quantitative dripping behavior of the set of materials by the particle finite element method (PFEM). Polymer properties (activation energy and Arrhenius coefficient of decomposition, char yield, density, effective heat of combustion, heat of decomposition, specific heat capacity, and thermal conductivity) in addition to rheological responses in high temperatures are estimated and measured as input parameters for the simulations. The dripping behavior obtained by simulated materials corresponds with the experimental results in terms of time and drop size. A consistent picture of the interplay of the different phenomena controlling dripping under fire appears to deliver a better understanding of the role of different materials’ properties KW - Dripping KW - UL 94 KW - PFEM KW - High heat resistance KW - Polyamide 4.6 KW - Flammability PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-586015 DO - https://doi.org/10.1002/mame.202300091 SN - 1439-2054 SN - 1438-7492 VL - 308 IS - 10 SP - 1 EP - 11 PB - Wiley-VCH AN - OPUS4-58601 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tamsen, Erik A1 - Agrawal, A. A1 - Koutsoureladkis, P. S. A1 - Unger, Jörg F. T1 - From concrete mixture to structural design an optimization framework to reduce the global warming potential N2 - Concrete has a long history in the construction industry and is currently one of the most widely used building materials. Unfortunately, the concrete industry has a significant impact on the environment by contributing to about 9% of the total anthropogenic greenhouse gas (GHG) emissions. Concrete is a highly complex composite material. However, the main source of concrete's GHG emissions is the cement. This leads to two main strategies when trying to reduce the environmental impact. The first is to reduce the cement within the concrete mix. This can be done by substituting it using additives or increasing the amount of aggregates. Usually this will lead to decreased material properties, like compressive strength or stiffness. The second option is to reduce the amount of required concrete by optimizing the topology of the structure. However, this might require higher compressive strength. In addition, there are other properties like to workability which need to be considered. All in all, this leads to a highly complex optimization problem, which requires the estimation of effective concrete properties, based on the mixture as input to a predictive simulation. We present an automated workflow framework which combines experimental data with simulations, calibrates the simulation and performs the desired optimization. This workflow includes classical FE models, design guidelines based on model codes, as well as data driven methods. The chosen example is a beam, for which the concrete mixture is optimized to reduce GHG emissions. The first step is an estimation of material parameters, based on experimental data. This includes measures of stochastic distribution, allowing the quantification of the quality of the estimated parameters. The second step is the optimization. It takes into account constraints like the loading capacity after 28 days, the maximum allowed temperature during cement hydration and the maximum time till demoulding. The applied models include a Mori-Tanaka-based homogenization method to estimate effective concrete parameters, an FE simulation including the evolution of the concrete compressive strength and stiffness, the temperature field, displacements, and stress. This research shows a way towards a more performance-oriented material design. T2 - M2P 2023 (First International Conference Math 2 Product) CY - Taormina, Italy DA - 30.05.2023 KW - Experimental data KW - Simulations PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-582545 AN - OPUS4-58254 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tabaka, Weronika A1 - Schartel, Bernhard T1 - Bench-scale fire stability testing - Protective layers in carbon fibre reinforced polymer laminates N2 - Fire resistance testing of components made of carbon fibre reinforced polymers (CFRP) composites usually demands intermediate-scale or full-scale testing. In this study, a bench-scale test is presented as a practicable and efficient method to assess the improvement in structural integrity of CFRP with different protective interlayers during fire. T2 - International Conference on Composite Materials (ICCM23) CY - Belfast, UK DA - 30.07.2023 KW - Fire resistance KW - Bench-scale testing KW - Carbon fibre reinforced polymer composite PY - 2023 AN - OPUS4-58099 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tabaka, Weronika A1 - Schartel, Bernhard T1 - Bench-scale fire stability testing of carbon fibre reinforced polymer laminates with protective layers N2 - Fire resistance testing of components made of carbon fibre reinforced polymers (CFRP) composites usually demands intermediate-scale or full-scale testing. In this study, a bench-scale test is presented as a practicable and efficient method to assess the improvement in structural integrity of CFRP with different protective interlayers during fire. Fire stability is one of the biggest issues of carbon fibre reinforced polymer (CFRP) composites, particularly when they are using in load bearing applications. As soon as the glass transition temperature of polymer matrix (100-200°C) is achieved, the composite loses its structural integrity, what leads to the distortion and failure. The principal fire stability test is based on simultaneous application of fire and mechanical load. Since the carbon fibres can transfer the tensile loads quite well, the compression load is chosen as a required mechanical load for a test. The fire tests were preceded by a static load test at room temperature to determine ultimate failure load. The specimen was loaded with a compression force until the failure load was reached, which was observed as a buckling. For the fire tests, 10% of compression failure load and direct flame of a fully developed fire (heat flux ≈ 180 kW m-2) were applied simultaneously to the specimen, while the time to failure was measured. The possibilities of bench-scale fire stability testing were presented by investigating new types of laminate structures, which exhibit promising flame retardancy and fireproof properties. The new approach of CFRP laminate differs with a protective concept. Every system consists of two different interlayers (titanium foil, thermoplastic foil PEI, ceramic layer WHIPOX, rubber tape Pyrostat, basalt fibres and kenaf fibres), where the one layer constitutes the fireproof protection, that delays the rise of temperature in the rest of laminate, and the second layer provides very good structural connection with carbon fibre layers, thus improves the mechanical integrity of CFRP composite in fire. The time to failure of CFRP composite was 17s. Protective systems significantly enhance the fire stability and increased time to failure by 3 to 10 times. Thicker specimens showed longer resistance time, however CFRP laminate with ceramic layer and titanium foil presented outstanding results and the best performance. The protection with Kenaf and basalt fibres offered a natural fibre solution with also good fire resistance performance Although bench-scale tests are limited with respect to assessing the performance of components and structures, they are valuable in the assessment of different materials concepts. Furthermore, the reduced effort of conducting bench-scale test (lower costs, time, personnel resources) makes it more practical and effective. T2 - 19th European meeting on Fire Retardant Polymeric Materials (FRPM23) CY - Dübendorf, Switzerland DA - 26.06.2023 KW - Fire resistance KW - Carbon fibre reinforced polymer KW - Bench-scale testing PY - 2023 AN - OPUS4-57880 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sunkavalli, Viswa Ratnasri A1 - Strangfeld, Christoph A1 - Maack, Stefan T1 - Thickness Measurements of Polyamide Specimens using Fluidic Oscillator as a Frequency Modulated Air-Coupled Ultrasonic Transducer N2 - Ultrasonic inspection, especially contact and immersion methods, have become established techniques for non-destructive testing in civil engineering (NDT-CE). However, the requirement for coupling agents renders these methods cumbersome in practice due to the potential for surface defacement and an arduous measurement process. Consequently, air-coupled ultrasonic transducers have been proposed as an alternative to address these concerns. These (alternatives), however, come with their own challenges, such as a significant impedance mismatch between the air and the specimen as well as the susceptibility of time of flight (TOF) measurements to ambient conditions. Recently, fluidic oscillators have been developed for in-air sound generation to alleviate impedance mismatch and improve the overall robustness, which is an important consideration of NDT-CE applications. The advantage of fluidic oscillators lies in their ability to generate an ultrasonic signal via oscillating air jet excited by a self-actuated fluctuation. Using air as the operating medium provides a supplementary benefit of lowering measurement durations in addition to a substantial drop in acoustic impedance losses with air acting both as an actuation as well as a coupling medium. Thus, TOF measurements using such fluidic transducers are expected to enable faster characterization of specimen parameters. In that regard, material characterization of polyamide is carried out using ultrasound generated by fluidic devices. Additionally, the mass flow rate of the operating fluid is observed to have a significant effect on the frequency of the fluidic oscillator. Accordingly, the frequency of the oscillation is modulated by varying the supply pressure, leading to a varying flow rate, which in turn facilitates a robust and reliable assessment of the TOF through the material by the generated chirp signals. Furthermore, such frequency modulations effectively improve the signal-to-noise ratio (SNR). Along with a comprehensive study of these new fluidic transducers, preliminary measurement findings are presented, including the material characterization of polymers using air-coupled, frequency-modulated ultrasound. T2 - European Conference on Non-Destructive Testing (ECNDT) CY - Lisbon, Portugal DA - 03.07.2023 KW - Air coupled ultrasound KW - Fluidic actuator PY - 2023 AN - OPUS4-57940 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sunder, S. A1 - Jauregui Rozo, Maria A1 - Schartel, Bernhard A1 - Ruckdäschel, H. T1 - Adapting intumescent/low-melting glass flame-retardant formulations for transfer to glass-fiber-reinforced composites and post-fire mechanical analysis N2 - The residual post-fire mechanical properties of fiber-reinforced epoxy composites are influenced by their fire residues after burning. This study uses intumescent/low-melting glass flame retardants to tailor fire residues in epoxy resin. Processibility of prepregs and their quality are analysed for transfer of the flame-retardant epoxy resins to layered glass-fiber reinforced composites. Minimal effects were found on the pre-fire flexural strengths of the composites due to low loading of the flame retardants. However, when transferred to glass-fiber reinforced composites, the fire residues diminish significantly. Further studies are required to improve theoretical and experimental estimations of the post-fire mechanics of the composites. T2 - SAMPE Europe Conference 2023 CY - Madrid, Spain DA - 03.10.2023 KW - Fire residue KW - Prepregs KW - Mechanics KW - Lightweight materials KW - Composites KW - Flame retardancy PY - 2023 SP - 1 EP - 7 AN - OPUS4-59138 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sunder, S. A1 - Jauregui Rozo, Maria A1 - Schartel, Bernhard A1 - Ruckdäschel, H. T1 - Microstructure analysis and mechanical characterization of flame-retardant epoxy resins transferred to glass fiber composites via prepregs N2 - The transfer of flame-retardant epoxy resin formulations to composites for structural and lightweight applications in the energy and transport sector can be complex and requires systematic investigation. Here, uncoated and silane-coated ammonium polyphosphate (APP, Si-APP) intumescent compounds are transferred to prepregs using a Bisphenol A diglycidyl ether (DGEBA) resin matrix to 0/90o bidirectional glass fibers with an aerial weight of 600 g/m2. Inorganic silicates (InSi) are added to improve the fire residues of the composites after combustion and the total amount of flame retardants in the resin formulations was 10% by weight. The prepregs' fiber volume content (FVC) is corroborated using in-process measurements and thermogravimetric analysis. This was found to be approximately 60% for the composites containing APP, which is ideal for load-bearing applications with high mechanical strength. However, the Si-APP containing prepregs showed an inconsistent FVC potentially due to interactions with the commercial sizing of the glass fibers. The composites subsequently prepared are analysed for potential filtration effects of the additives via SEM after immobilization in a cured resin and platinum sputtering. The inter-laminar shear strength and the mechanical strength of the composites are compared via three-point bending tests. Additionally, the fire performance of the composites is analysed using cone calorimetry. It was found there was minimal impact of the loading of the flame retardants on the delamination of the composites and the flexural strength. However, the high density of the glass fibers possibly results in a suppression of the mode of action of the flame retardants in the composites. Therefore, the fire residues of the composites are further compared using SEM, and the flame-retardant modes of action upon transfer are investigated. T2 - FEMS EUROMAT 23 CY - Frankfurt am Main, Germany DA - 03.09.2023 KW - Lightweight construction KW - Flame retardancy KW - Composites PY - 2023 AN - OPUS4-59136 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sunder, S. A1 - Jauregui Rozo, Maria A1 - Schartel, Bernhard A1 - Ruckdäschel, H. T1 - Adapting intumescent/low-melting glass flame-retardant formulations for transfer to glass-fiber-reinforced composites and post-fire mechanical analysis N2 - The residual post-fire mechanical properties of fiber-reinforced epoxy composites are influenced by their fire residues after burning. This study uses intumescent/low-melting glass flame retardants to tailor fire residues in epoxy resin. Processibility of prepregs and their quality are analysed for transfer of the flame-retardant epoxy resins to layered glass-fiber reinforced composites. Minimal effects were found on the pre-fire flexural strengths of the composites due to low loading of the flame retardants. However, when transferred to glass-fiber reinforced composites, the fire residues diminish significantly. Further studies are required to improve theoretical and experimental estimations of the post-fire mechanics of the composites. T2 - SAMPE Europe Conference 2023 CY - Madrid, Spain DA - 03.10.2023 KW - Composites KW - Flame retardancy KW - Lightweight KW - Post fire mechanics KW - Intumescent PY - 2023 AN - OPUS4-59137 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strobl, Dominic A1 - Robens-Radermacher, Annika A1 - Ghnatios, Ch. A1 - Pittner, Andreas A1 - Rethmeier, Michael A1 - Unger, Jörg F. T1 - Reduced Order Model with Domain Mapping for Temperature Field Simulation of Wire Arc Additive Manufacturing N2 - Additive manufacturing (AM) has revolutionized the manufacturing industry, offering a new paradigm to produce complex geometries and parts with customized properties. Among the different AM techniques, the wire arc additive manufacturing (WAAM) process has gained significant attention due to its high deposition rate and low equipment cost. However, the process is characterized by a complex thermal history, dynamic metallurgy, and mechanical behaviour that make it challenging to simulate it in real-time for online process control and optimization. In this context, a reduced order model (ROM) using the proper generalized decomposition (PGD) method is proposed as a powerful tool to overcome the limitations of conventional numerical methods and enable the real-time simulation of the temperature field of WAAM processes. Though, the simulation of a moving heat source leads to a hardly separable parametric problem, which is handled by applying a novel mapping approach. Using this procedure, it is possible to create a simple separated representation of the model, also allowing to simulate multiple layers. In this contribution, a PGD model is derived for the WAAM procedure simulating the temperature field. A good agreement with a standard finite element method is shown. The reduced model is further used in a stochastic model parameter estimation using Bayesian inference, speeding up calibrations and ultimately leading to a calibrated real-time simulation. T2 - SIM-AM 2023 CY - Munich, Germany DA - 26.07.2023 KW - Additive manufacturing KW - Reduced Order Model PY - 2023 AN - OPUS4-58253 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strobl, Dominic A1 - Robens-Radermacher, Annika A1 - Ghnatios, C. A1 - Pittner, Andreas A1 - Rethmeier, Michael A1 - Unger, Jörg F. T1 - Reduced Order Model for Temperature Field Simulation of Wire Arc Additive Manufacturing with Domain Mapping N2 - Additive manufacturing (AM) has revolutionized the manufacturing industry, offering a new paradigm to produce complex geometries and parts with customized properties. Among the different AM techniques, the wire arc additive manufacturing (WAAM) process has gained significant attention due to its high deposition rate and low equipment cost. However, the process is characterized by a complex thermal history making it challenging to simulate it in real-time for online process control and optimization. In this context, a reduced order model (ROM) using the proper generalized decomposition (PGD) method [1] is proposed as a powerful tool to overcome the limitations of conventional numerical methods and enable the real-time simulation of the temperature field of WAAM processes. These simulations use a moving heat source leading to a hardly separable parametric problem, which is handled by applying a novel mapping approach [2]. This procedure makes it possible to create a simple separated representation of the model, which allows to simulate multiple layers. In this contribution, a PGD model is derived for the temperature field simulation of the WAAM process. A good agreement with a standard finite element method is shown. The reduced model is further used in a stochastic model parameter estimation using Bayesian inference, speeding up calibrations and ultimately leading to a calibrated real-time simulation. T2 - MORTech 2023 - 6th International Workshop on Model Reduction Techniques CY - Paris, France DA - 22.11.2023 KW - Wire arc additive manufacturing KW - Reduced order modelling PY - 2023 AN - OPUS4-59105 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Strangfeld, Christoph A1 - Stolpe, Heiko A1 - Wiehle, Philipp T1 - Moisture diffusion affected by the Knudsen effect in temporal changing pore networks N2 - Almost all building materials in civil engineering have an open porosity and interact with or are affected by the environmental conditions. Structures might suffer from effects such as moisture adsorption, carbonation, corrosion, penetration of salt ions and chemical substances, etc. In the hygroscopic range, these processes are mostly driven by diffusion. Due to the confinement of small pores (less than1 µm), the Knudsen effect reduces the molecular diffusion. This reduction can become more significant in case of temporal changing pore systems because of physisorption of water vapor, carbonation, or chemisorption. In this study, unstabilised earth blocks and earth masonry are investigated. In a first step, the pore size distribution of the blocks is measured and sorption isotherms are recorded in experiments. Besides the ordinary physisorption, the involved clay minerals undergo swelling or shrinking due to chemisorption. The following two effects must be considered: first, the reduction of the available pore space by the adsorbed water layer. For this, the Hillerborg sorption theory is used, which is a combination of the well-known Brunauer-Emmett-Teller sorption theory and the Kelvin equation. This allows the computation of adsorbed water layers even in curved pore geometries. Second, the variation of the initial pore size distribution due to chemisorption needs to be modelled. Based on these two models, the effective diffusion coefficient can be predicted. For validation, arrays of relative humidity sensors were embedded into a free-standing earth masonry wall. This monitoring was carried out over more than a year to have a broad variety of environmental conditions and was located in Berlin, Germany. The prediction of the effective diffusion coefficient can also be transferred to other processes and allows the investigation of materials having temporarily changing pore systems. Examples are the carbonation of cementitious materials, alkali silica reaction, calcium leaching of long-lasting structures, etc. These effects are prominent in the meso-pore range and might significantly alter the effective diffusion coefficient. KW - Earth material KW - Material moisture KW - Physisoprtion KW - Chemisorption PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-583811 DO - https://doi.org/10.1016/j.matpr.2023.09.034 SN - 2214-7853 SP - 1 EP - 8 PB - Elsevier Ltd. CY - Amsterdam, Niederlande AN - OPUS4-58381 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Stolpe, Heiko A1 - Wiehle, Philipp T1 - Moisture diffusion affected by the Knudsen effect in temporal changing pore networks N2 - Almost all building materials in civil engineering have an open porosity and interact with or are affected by the environmental conditions. Structures might suffer from effects such as moisture adsorption, carbonation, corrosion, penetration of salt ions and chemical substances, etc. In the hygroscopic range, these processes are mostly driven by diffusion. Due to the confinement of small pores (< 1 µm), the Knudsen effect reduces the molecular diffusion. This reduction can become more significant in case of temporal changing pore systems because of physisorption of water vapor, carbonation, or chemisorption. In this study, unstabilised earth blocks and earth masonry are investigated. In a first step, the pore size distribution of the blocks is measured and sorption isotherms are recorded in experiments. Besides the ordinary physisorption, the involved clay minerals undergo swelling or shrinking due to chemisorption. The following two effects must be considered: first, the reduction of the available pore space by the adsorbed water layer. For this, the Hillerborg sorption theory is used, which is a combination of the well-known Brunauer-Emmett-Teller sorption theory and the Kelvin equation. This allows the computation of adsorbed water layers even in curved pore geometries. Second, the variation of the initial pore size distribution due to chemisorption needs to be modelled. Based on these two models, the effective diffusion coefficient can be predicted. For validation, arrays of relative humidity sensors were embedded into a free-standing earth masonry wall. This monitoring was carried out over more than a year to have a broad variety of environmental conditions and was located in Berlin, Germany. The prediction of the effective diffusion coefficient can also be transferred to other processes and allows the investigation of materials having temporarily changing pore systems. Examples are the carbonation of cementitious materials, alkali silica reaction, calcium leaching of long-lasting structures, etc. This effect becomes most prominent in the meso-pore range and might alter the effective diffusion coefficient by more than 100 %. T2 - 4th International Congress on Materials & Structural Stability CY - Rabat, Morocco DA - 08.03.2023 KW - Earth masonry KW - Material moisture KW - Molecular diffusion KW - Chemisoprtion KW - Knudsen effect KW - Physisorption PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-571391 SP - 1 EP - 8 PB - RILEM CY - Champs-sur-Marne AN - OPUS4-57139 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Strangfeld, Christoph A1 - Küttenbaum, Stefan T1 - Zur Visualisierung von Schäden in Betonschwellen durch zerstörungsfreie Ultraschallprüfung N2 - Die bildgebende Ultraschalltechnik liefert Hinweise auf verdeckte Schäden in Spannbetonschwellen. Dieses zerstörungsfreie Prüfverfahren schafft eine objektive und vergleichbare Basis für die Zustandsbestimmung der Schwellen und ermöglicht die Optimierung von baulichen Erhaltungsstrategien. KW - Spannbetonschwellen KW - Zustandsbewertung KW - Verkehrsinfrastruktur PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-592914 UR - https://www.eurailpress.de/magazine.html SN - 0013-2845 IS - 12/23 SP - 26 EP - 31 PB - DVV Media Group CY - Hamburg AN - OPUS4-59291 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Stolpe, Heiko A1 - Wiehle, Philipp T1 - Moisture diffusion affected by the Knudsen effect in temporal changing pore networks N2 - Almost all building materials in civil engineering have an open porosity and interact with or are affected by the environmental conditions. Structures might suffer from effects such as moisture adsorption, carbonation, corrosion, penetration of salt ions and chemical substances, etc. In the hygroscopic range, these processes are mostly driven by diffusion. Due to the confinement of small pores ( 1 m), the Knudsen effect reduces the molecular diffusion. This reduction can become more significant in case of temporal changing pore systems because of physisorption of water vapor, carbonation, or chemisorption. In this study, unstabilised earth blocks and earth masonry are investigated. In a first step, the pore size distribution of the blocks is measured and sorption isotherms are recorded in experiments. Besides the ordinary physisorption, the involved clay minerals undergo swelling or shrinking due to chemisorption. The following two effects must be considered: first, the reduction of the available pore space by the adsorbed water layer. For this, the Hillerborg sorption theory is used, which is a combination of the well-known Brunauer-Emmett-Teller sorption theory and the Kelvin equation. This allows the computation of adsorbed water layers even in curved pore geometries. Second, the variation of the initial pore size distribution due to chemisorption needs to be modelled. Based on these two models, the effective diffusion coefficient can be predicted. For validation, arrays of relative humidity sensors were embedded into a free-standing earth masonry wall. This monitoring was carried out over more than a year to have a broad variety of environmental conditions and was located in Berlin, Germany. The prediction of the effective diffusion coefficient can also be transferred to other processes and allows the investigation of materials having temporarily changing pore systems. Examples are the carbonation of cementitious materials, alkali silica reaction, calcium leaching of long-lasting structures, etc. This effect becomes most prominent in the meso-pore range and might alter the effective diffusion coefficient by more than 100 %. T2 - 4th International Congress on Materials & Structural Stability CY - Rabat, Morocco DA - 08.03.2023 KW - Earth masonry KW - Material moisture KW - Molecular diffusion KW - Chemisoprtion KW - Knudsen effect KW - Physisorption PY - 2023 AN - OPUS4-57140 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spitzer, Stefan A1 - Riesner, G. A1 - Zakel, S. A1 - Schierding, C. T1 - A New Ignition Source for the Determination of Safety Characteristics of Gases N2 - Safety characteristics are used to keep processes, including flammable gases, vapors, and combustible dusts, safe. In the standards for the determination of safety characteristics of gases and vapors, the induction spark is commonly used. However, classic transformers are hard to obtain, and replacement with new electronic transformers is not explicitly allowed in the standards. This article presents the investigation of five gases that are normally used to calibrate devices for the determination of safety characteristics, the maximum experimental safe gap (MESG), with an electronic transformer, and the values are compared to the ones that are obtained with the standard transformer. Additionally, calorimetric measurements on the net energy of both ignition sources were performed as well as open-circuit voltage measurements. It is concluded that the classic type of transformer can be replaced by the new type obtaining the same results for the MESG and introducing the same amount of energy into the system. KW - Safety characteristics KW - Ignition sources KW - MESG PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-578528 DO - https://doi.org/10.3390/gases3030007 VL - 3 IS - 3 SP - 106 EP - 111 PB - MDPI CY - Basel AN - OPUS4-57852 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spitzer, Stefan A1 - Krietsch, Arne A1 - Jankuj, Vojtech T1 - Experimental Parameter Study and Inherent Scattering of Safety Characteristics of Dusts N2 - Safety characteristics are widely used in industrial processes to avoid explosive atmospheres (primary explosionprotection) or to mitigate the consequences of an explosion (constructive explosion protection). Several laboratory parameters influence the determined values when performing the test series such as the beginning pressure and the pre-ignition pressure rise, the ignition source, the ignition energy, the burning duration and volume or the concentration of the combustible substance. In the different standards for the determination of safety characteristics of dusts there is no statement about the scattering or the deviation when parameters are chosen or occur on the borders of their allowed range. Thus, two laboratories might determine values that are hardly comparable for the same given substance. This article summarizes some of the influential factors that cause a deviation and shows the inherent scattering of dust tests when all other parameters are kept constant. It also provides some advice how to minimize the deviation and the scattering with little effort. T2 - FEx23 CY - Bologna, Italy DA - 08.10.2023 KW - Safety characteristics KW - Inherent Scattering KW - Dust Explosions PY - 2023 DO - https://doi.org/10.3303/CET23104001 VL - 104 SP - 1 EP - 6 PB - AIDIC CY - Milano AN - OPUS4-58872 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spitzer, Stefan A1 - Jankuj, V. A1 - Hecht, K. A1 - Krietsch, Arne T1 - Igniting volume of four ignition sources N2 - Several standardized ignition sources are used to determine the safety characteristics of gases, vapours and dusts. Standards indicate the source of ignition but vary in specifying other features such as the burning duration, energy or the volume in which the energy is released. Since heat is not visible under normal conditions, a schlieren technique was used to visualize the entire igniting volume and not just the flames. This article focuses on the igniting volume, compares it among the four standardized ignition sources and displays its relationship to the size of the test vessel. Differences in the ignition behaviour of the ignition sources might lead to the determination of erroneous safety characteristics and with that to the unsafe operation of processes. KW - Hybrid mixtures KW - 20L-sphere KW - Ignition sources KW - Exploding wire PY - 2023 DO - https://doi.org/10.1016/j.psep.2022.12.076 SN - 0957-5820 VL - 170 SP - 1200 EP - 1207 PB - Elsevier CY - Amsterdam AN - OPUS4-56855 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spitzer, Stefan A1 - Askar, Enis A1 - Hecht, Kristin A1 - Gabel, Dieter A1 - Geoerg, Paul A1 - Krause, Ulrich A1 - Dufaud, Olivier A1 - Krietsch, Arne ED - Amyotte, Paul T1 - The maximum rate of pressure rise of hybrid mixtures N2 - The maximum rate of pressure rise (dp/dt)𝑚𝑎𝑥 and the corresponding K-value of hybrid mixtures containing flammable gases and dusts are important for constructive explosion protection measures. Since the safety characteristics of dusts and gases are determined under different conditions, there has been considerable confusion about the influence of flammable gas on the (dp/dt) of dusts and vice versa. While some investigations showed comparably higher values for hybrid mixtures, others stated that the highest value for the gas component alone is the worst case. The first part of this paper focuses on the confusion around the different statements about (dp/dt)𝑚𝑎𝑥 of hybrid mixtures and where they come from. In the second part of this paper experimental results are presented that illustrate how to clarify the different findings of past research and show what to expect as a real worst-case-value for hybrid mixtures. KW - Hybrid Mixtures KW - 20L-sphere KW - Turbulent combustion KW - Maximum rate of pressure rise PY - 2023 DO - https://doi.org/10.1016/j.jlp.2023.105178 SN - 0950-4230 SN - 1873-3352 VL - 86 SP - 1 EP - 9 PB - Elsevier CY - Amsterdam AN - OPUS4-58435 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Spitzer, Stefan T1 - Influence of the ignition source on the Safety Characteristics of hybrid dust-gas mixtures N2 - Safety characteristics like the lower explosion limit, the highest concentration for a given substance mixed with air that does not result in a self-propagating flame, or the maximum explosion pressure, the highest pressure that can be reached after ignition for a given combustible substance mixed with air at any concentration, are widely used in the industry to either prevent an explosion or to mitigate the effects of it. Safety characteristics are not physical constants, are determined experimentally and depend on the chosen experimental parameters such as the ignition energy or turbulence. For the determination of the safety characteristics lower explosion limit (LEL), limiting oxygen concentration (LOC), maximum explosion pressure (pmax) and maximum rate of pressure rise ((dp/dt)max) of gases and vapors the gas is filled via partial pressures into a test vessel and then ignited under quiescent conditions with a weak (2 J - 20 J) ignition source. For dusts, the same safety characteristics are determined under turbulent conditions to elevate the dust homogeneously and it is ignited with two chemical igniters with an ignition energy of 1000 J each (LEL and LOC) or 5000 J each (pmax and (dp/dt)max). For the determination of safety characteristics of hybrid mixtures (a mixture containing a combustible dust and a flammable gas) there is no existing standard. In the last 40 years most of the research on their safety characteristics was performed with dust testing equipment that was modified for the addition of flammable gas. Because of the different mixing procedures of gases and dusts with air and because of different ignition energies and sources that are normally used for the standard tests of gases or dusts, the results were hardly reproducible. Statements about the different safety characteristics were contradictory and left the reader or the person responsible for designing safety measures for a process plant or a facility behind with no clear suggestion about the behavior of hybrid mixtures. This thesis is aimed on determining the influence of the different ignition sources and energies on the safety characteristics pmax, (dp/dt)max, lower explosion limit, and limiting oxygen concentration of hybrid mixtures. Several test series were conducted to characterize different standardized ignition sources, that are already in use for the determination of safety characteristics of single-phase substances (gases, liquids, dusts). The burning duration, the igniting volume and the net energy were investigated. It was shown, that the chemical igniters and the exploding wire are suitable ignition sources for the determination of safety characteristics of hybrid mixtures in general. Their burning duration was long enough to ignite dusts and quick enough, that the decay of the turbulence or sedimentation of the dusts did not occur. Both ignition sources produced comparable results for the determination of pmax, LEL and (dp/dt)max of dusts when they had the same ignition energy. A reduced ignition energy of the exploding wire and the chemical igniters did not affect the pmax and (dp/dt)max. The LEL changed with lower energies. However, for the determination of the LOC of hybrid mixtures the exploding wires with an overall energy of 2 kJ produced the best results. The influence of the different mixing procedures that have already been used for hybrid mixtures and the requirements for them were also investigated experimentally for the gas concentration and the determined safety characteristics and compared to each other. It was shown, that the partial pressure method works for mixing hybrid mixtures but the pressures should be measured very accurately and the gas concentration should be validated. Furthermore, the influence of the turbulence that is inevitable when testing dusts, on the safety characteristics of gases was determined. It was found that the chemical igniters and exploding wires produced comparable results for the determination of pmax, LEL and (dp/dt)max under turbulence. For the LOC only exploding wires with two times 1 kJ worked. Finally, the safety characteristics of hybrid mixtures were determined with different ignition energies and sources and the data were compared. It was discovered, that the pmax of hybrid mixtures was the same value than the higher determined one of the single substances while (dp/dt)max of hybrid mixtures was about 10 % to 25 % higher than the value of the stoichiometric gas mixture under turbulence. The point was found at the stoichiometric gas concentration with very little amounts of dust. To prove the key findings of this work and for the establishment of a standardized procedure for the determination of safety characteristics of hybrid mixtures, an international round robin test was conducted with eleven participating facilities in seven countries. The results were comparable within a reasonable range and are presented in this dissertation in an extra chapter. Based upon the observations in this work a reliable solution for a new standardizable ignition source to determine the safety characteristics of hybrid dust-gas-mixtures is proposed. KW - Ignition Sources KW - Hybrid Mixtures KW - Explosions PY - 2023 SP - 1 EP - 132 AN - OPUS4-58905 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sperlich, Tim A1 - Häßler, Dustin A1 - Stelzner, Ludwig A1 - Hothan, Sascha T1 - In situ Prüfmethode zur Untersuchung des Feuerwiderstands von bestehenden Stahlkonstruktionen mit reaktivem Brandschutzsystem N2 - Der Beitrag beschreibt die Entwicklung eines neuartigen in situ Nachweisverfahrens zur Beurteilung des Feuerwiderstandes von bestehenden Stahlkonstruktionen mit gealtertem reaktivem Brandschutzsystem (RBS). Derzeit ist ein solcher Nachweis ausschließlich anhand eines Bauteilbrandversuchs möglich. Hierzu muss ein Bauteil aus der Bestandskonstruktion entnommen und einer zerstörenden Brandprüfung unterzogen werden. In Zusammenhang mit der Dauerhaftigkeitsbewertung von RBS für Zeiträume von mehr als 10 Jahren besteht in der Praxis vermehrt der Bedarf an einem minimal invasiven Prüfverfahren, mit dessen Hilfe sich direkt am Bestandsbauwerk die tatsächlich vorhandene Leistungsfähigkeit des gealterten RBS überprüfen lässt. Durch einen erfolgreichen Funktionsnachweis wäre eine Weiternutzung der Bestandkonstruktion bei Aufrechterhaltung des bestehenden Sicherheitsniveaus möglich. T2 - Symposium Heißbemessung - Structural Fire Engineering CY - Braunschweig, Germany DA - 05.09.2023 KW - Brandschutz KW - Stahlbau KW - reaktives Brandschutzsystem KW - Prüfmethode KW - Brandversuch PY - 2023 SP - 1 EP - 16 PB - TU Braunschweig CY - Braunschweig AN - OPUS4-58180 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sperlich, Tim A1 - Häßler, Dustin A1 - Stelzner, Ludwig A1 - Hothan, Sascha T1 - In situ Prüfmethode zur Untersuchung des Feuerwiderstands von bestehenden Stahlkonstruktionen mit reaktivem Brandschutzsystem N2 - Der Beitrag beschreibt die Entwicklung eines neuartigen in situ Nachweisverfahrens zur Beurteilung des Feuerwiderstandes von bestehenden Stahlkonstruktionen mit gealtertem reaktivem Brandschutzsystem (RBS). Derzeit ist ein solcher Nachweis ausschließlich anhand eines Bauteilbrandversuchs möglich. Hierzu muss ein Bauteil aus der Bestandskonstruktion entnommen und einer zerstörenden Brandprüfung unterzogen werden. In Zusammenhang mit der Dauerhaftigkeitsbewertung von RBS für Zeiträume von mehr als 10 Jahren besteht in der Praxis vermehrt der Bedarf an einem minimal invasiven Prüfverfahren, mit dessen Hilfe sich direkt am Bestandsbauwerk die tatsächlich vorhandene Leistungsfähigkeit des gealterten RBS überprüfen lässt. Durch einen erfolgreichen Funktionsnachweis wäre eine Weiternutzung der Bestandkonstruktion bei Aufrechterhaltung des bestehenden Sicherheitsniveaus möglich. T2 - Symposium Heißbemessung - Structural Fire Engineering CY - Braunschweig, Germany DA - 05.09.2023 KW - Brandschutz KW - Stahlbau KW - Reaktives Brandschutzsystem KW - Prüfmethode KW - Brandversuch PY - 2023 AN - OPUS4-58183 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Patrick T1 - Zustandsbewertung von Bauwerken unter veränderlichen Umgebungsbedingungen mittels Structural Health Monitoring N2 - Brücken sind Teil der alternden Verkehrsinfrastruktur. Um die Nutzungsdauer zu verlängern und plötzliche Schäden zu detektieren kann Bauwerksmonitoring ("Structural Health Monitoring") eingesetzt werden. Der Einfluss von Umgebungsbedingungen, beispielsweise der Temperatur, auf das Bauwerksverhalten ist meist größer als der Einfluss von Schäden. Diese Einflüsse bestmöglich voneinander zu trennen und Veränderungen im Tragverhalten korrekt Schäden oder Umgebungsbedingungen zuzuordnen ist eine offene Forschungsfrage. Diese Arbeit zeigt eine mögliche Lösung, bei der gekoppelte Modelle von Umwelteinflüssen, Schäden und Tragverhalten des Bauwerks auf Grundlage von Monitoringdaten aktualisiert werden. Das Framework dazu wird vorgestellt und an einem Laborexperiment eines Stahlbetonbalkens in der Klimakammer angewandt. Die Ergebnisse bestätigen die Vorgehensweise. In nächsten Schritten müssen komplexere Tragwerke und die Sensitivität des Ansatzes untersucht werden. T2 - Forschungskolloquium, Institut für Konstruktiven Ingenieurbau, Bauhaus-Universität Weimar CY - Weimar, Germany DA - 28.06.2023 KW - Structural health monitoring KW - Bauwerksmonitoring KW - Umwelteinflüsse KW - Brücken PY - 2023 AN - OPUS4-58005 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Katja A1 - Stahl, Michael A1 - Farahbakhsh, Mahin T1 - Fachinformationssystem Datenbank GEFAHRGUT N2 - Es werden die Anwendungen des Gefahrgutdatenpools der BAM aufgezeigt, der ein zentrales Informationssystem für den Transport gefährlicher Güter darstellt. T2 - Stuttgarter Gefahrguttag CY - Stuttgart, Germany DA - 24.10.2023 KW - BAM-Liste KW - Datenbank GEFAHRGUT KW - Gefahrgut-Schnellinfo KW - Gefahrgutdatenpool KW - Gefahrguttransport KW - Informationssystem KW - Kurzinfo KW - Modul für Beförderungspapiere KW - Modul für radioaktive Stoffe KW - BAM List KW - Dangerous Goods Database KW - Dangerous Goods Quickinfo KW - Radioactive Materials Module KW - Transport Documents Module PY - 2023 AN - OPUS4-58710 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Katja A1 - Stahl, Michael A1 - Farahbakhsh, Mahin T1 - Fachinformationssystem Datenbank GEFAHRGUT - Hilfe bei der Kennzeichnung der Umweltgefahr N2 - Möglichkeiten der Datenbank GEFAHRGUT und des Gefahrgutdatenservices die Notwendigkeit der Kennzeichnung der Umweltgefahr zu ermitteln. T2 - Stuttgarter Gefahrguttag CY - Stuttgart, Germany DA - 24.10.2023 KW - Datenbank KW - Fachinformationssystem KW - Gefahrgut KW - Kennzeichnung KW - Umweltgefahr KW - Dangerous goods KW - Database KW - Environmentally hazardous substance KW - Labelling KW - Specialised information system PY - 2023 AN - OPUS4-58711 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sigrüner, M. A1 - Hüsken, Götz A1 - Pirskawetz, Stephan A1 - Herz, J. A1 - Muscat, D. A1 - Strübbe, N. T1 - Pull-out behavior of polymer fibers in concrete N2 - The bond between polymer fibers and the surrounding cementitious matrix is essential for the development of concrete reinforcement. The single fiber pull-out test (SFPT) is the standard characterization technique for testing the bond strength. However, the different phases of debonding cannot be distinguished by the SFPT. This study investigates the debonding of different polymer fibers from the surrounding cementitious matrix with a modified SFPT and proposes methods to change the SFPT setup to generate more valuable information on the debonding mechanism. The SFPT was equipped with linear variable differential transformers (LVDT), digital image correlation (DIC) and acoustic emission (AE) analysis. The results demonstrate that the modified SFPT allows a better understanding of the different phases of debonding during fiber pull-out. Furthermore, bond strength values calculated by different methods reveal that the chemical bond of the investigated polymers is not different as reported by previous studies. Deformation measurements performed using LVDTs and DIC are suitable measuring techniques to characterize the debonding mechanism in SFPT. A correlation between recorded AE and debonding phases was not found. KW - Polymer Fibres KW - Concrete KW - Pull-Out Behaviour KW - Debonding Mechanism PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-582918 DO - https://doi.org/10.1002/pol.20230264 SN - 2642-4169 SP - 1 EP - 13 PB - Wiley Periodicals, LLC. AN - OPUS4-58291 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Signorini, Cesare A1 - Bracklow, Franz A1 - Hering, Marcus A1 - Butler, Marko A1 - Leicht, Lena A1 - Schubert, Thomas A1 - Beigh, Mirza A.B. A1 - Beckmann, Birgit A1 - Curbach, Manfred A1 - Mechtcherine, Viktor T1 - Ballistic limit and damage assessment of hybrid fibre-reinforced cementitious thin composite plates under impact loading N2 - Impact resistance of reinforced concrete (RC) structures can be significantly improved by strengthening RC members with thin composite layers featuring high damage tolerance. Indeed, to limit the well-known vulnerability of cement-based materials against impact loading, the synergistic effects of short fibres and continuous textile meshes as hybrid reinforcement has been proved to be highly beneficial. This paper addresses the characterisation of novel cement-based hybrid composites through accelerated drop-weight impact tests conducted on rectangular plates at different impact energies. Two distinct matrices are assessed, with particular interest in a newly developed limestone calcined clay cement (LC3)-based formulation. Important parameters quantifying energy dissipation capability, load bearing capacity and damage are cross-checked to compute the ballistic limit and estimate the safety-relevant characteristics of the different composites at hand. Although textiles alone can improve the damage tolerance of fine concrete to some extent, the crack-bridging attitude of short, well-dispersed fibres in hybrid composites imparts a certain ductility to the cement-based matrices, allowing a greater portion of the textile to be activated and significantly reducing the amount of matrix spalling under impact. KW - Impact loading KW - Cement-based composites KW - SHCC KW - TRC KW - Sustainable binders PY - 2023 DO - https://doi.org/10.1016/j.jobe.2023.108037 VL - 80 SP - 1 EP - 21 PB - Elsevier Ltd. AN - OPUS4-58793 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Seifert, Lando A1 - Philipp, Markus A1 - Ebell, Gino A1 - Moersch, Jörg A1 - Müller, Thoralf T1 - Final report on WIPANO research project - A new test method for evaluating prestressing steels' susceptibility to stress corrosion cracking N2 - For the safety of prestressed concrete structures, a test of prestressing steel products for hydrogen-induced stress corrosion cracking is mandatory. The current standardized test methods according to DIN EN ISO 15630-3 have proven deficiencies concerning the reproducibility of the results and thus make it difficult to assess the susceptibility clearly. The WIPANO research project funded by BMWK aimed to improve the test method regarding reproducibility and reliability of results. The project created constant and reproducible test conditions by modifying material, electrolyte, and process parameters. This allowed a clear differentiation between good and bad products. As part of the project, a round robin test was initiated to confirm the applicability and reproducibility of the new test method. The new test method was evaluated for its applicability to the prestressing steel product wire. A draft standard with a proposed conformity criterion for these products was submitted to the responsible ISO committee for approval. According to the current feedback from the committee, the draft standard will be included in the informative annex of the testing standard, which could pave the way for mirroring at European and national standardization levels. KW - Prestressing steels KW - ISO 15630-3 KW - Hydrogen-induced stress corrosion cracking KW - Brittle fracture PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-581269 DO - https://doi.org/10.26272/opus4-58126 N1 - Funding source: Federal Ministry of Economic Affairs and Climate Action (BMWK), 11019 Berlin; FKZ: 03TNH019A/B/D SP - 1 EP - 106 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-58126 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Seifert, Lando A1 - Philipp, M. A1 - Ebell, Gino A1 - Moersch, J. A1 - Müller, Thoralf T1 - Gemeinsamer Schlussbericht zum Forschungsvorhaben - Entwicklung eines neuen Prüfverfahrens zur Beurteilung der Spannungsrisskorrosionsempfindlichkeit von Spannstählen für den Spannbetonbau N2 - Für die Sicherheit von Spannbetonbauwerken ist eine Empfindlichkeitsprüfung von Spannstahlprodukten gegenüber der wasserstoffinduzierten Spannungsrisskorrosion zwingend erforderlich. Die derzeitig normativ festgelegten Prüfmethoden nach DIN EN ISO 15630-3 zeigen nachweislich Schwächen hinsichtlich der Reproduzierbarkeit der Ergebnisse und erschweren damit die eindeutige Bewertung der Empfindlichkeit. Ziel des Forschungsvorhabens der Förderinitiative WIPANO des BMWK war es, die Prüfmethode hinsichtlich der Reproduzierbarkeit und Aussagesicherheit zu verbessern. Im Projekt wurden durch materialseitige, elektrolytische und verfahrenstechnische Parameteränderungen konstante und reproduzierbare Prüfbedingungen geschaffen. Dies ermöglichte eine eindeutige Differenzierung zwischen Gut- und Schlechtprodukten. Innerhalb des Projekts wurde ein Ringversuch initiiert, welcher die Anwendbarkeit und Reproduzierbarkeit der neuen Prüfmethode bestätigte. Das neue Prüfverfahren wurde hinsichtlich der Anwendbarkeit für das Spannstahlerzeugnis Draht evaluiert. Ein entsprechender Normentwurf mit einem Vorschlag für ein Konformitätskriterium dieser Erzeugnisse wurde dem zuständigen ISO-Gremium präsentiert und zur Abstimmung überlassen. Nach aktueller Rückmeldung seitens des Gremiums wird der Normentwurf den Eingang in den informativen Anhang der Prüfnorm finden, dies könnte den Weg für eine Spiegelung auf europäischer und nationaler Normungsebene ebnen. KW - Spannstahl KW - Spannungsrisskorrosion KW - ISO 15630-3 KW - Wasserstoff KW - Permeationsmessung KW - WIPANO PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-577922 DO - https://doi.org/10.26272/opus4-57792 SP - 1 EP - 106 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-57792 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Seifert, Lando A1 - Müller, Thoralf A1 - Ebell, Gino T1 - Schlussbericht zum Forschungsvorhaben: "WIPANO Spannstahlsicherheit" - Entwicklung eines neuen Prüfverfahrens zur Beurteilung der Spannungsrisskorrosionsempfindlichkeit von Spannstählen für den Spannbetonbau N2 - Für die Sicherheit von Spannbetonbauwerken ist eine Empfindlichkeitsprüfung von Spannstahlprodukten gegenüber der wasserstoffinduzierten Spannungsrisskorrosion zwingend erforderlich. Die derzeitig normativ festgelegten Prüfmethoden nach DIN EN ISO 15630-3 zeigen nachweislich Schwächen hinsichtlich der Reproduzierbarkeit der Ergebnisse und erschweren damit die eindeutige Bewertung der Empfindlichkeit. Ziel des Forschungsvorhabens der Förderinitiative WIPANO des BMWK war es, die Prüfmethode hinsichtlich der Reproduzierbarkeit und Aussagesicherheit zu verbessern. Im Projekt wurden durch materialseitige, elektrolytische und verfahrenstechnische Parameteränderungen konstante und reproduzierbare Prüfbedingungen geschaffen. Dies ermöglichte eine eindeutige Differenzierung zwischen Gut- und Schlechtprodukten. Innerhalb des Projekts wurde ein Ringversuch initiiert, welcher die Anwendbarkeit und Reproduzierbarkeit der neuen Prüfmethode bestätigte. Das neue Prüfverfahren wurde hinsichtlich der Anwendbarkeit für das Spannstahlerzeugnis Draht evaluiert. Ein entsprechender Normentwurf mit einem Vorschlag für ein Konformitätskriterium dieser Erzeugnisse wurde dem zuständigen ISO-Gremium präsentiert und zur Abstimmung überlassen. Nach aktueller Rückmeldung seitens des Gremiums wird der Normentwurf den Eingang in den informativen Anhang der Prüfnorm finden, dies könnte den Weg für eine Spiegelung auf europäischer und nationaler Normungsebene ebenen. KW - Spannstahl KW - Prestressing Steels KW - DIN EN ISO 15630-3 KW - Spannungsrisskorrosion KW - Stress corrosion cracking KW - Wasserstoff KW - Hydrogen PY - 2023 SP - 1 EP - 94 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-57402 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seifert, Lando A1 - Burkert, Andreas A1 - Müller, Thoralf A1 - Lehmann, Jens T1 - Grundlagen Korrosion und Korrosionsschutz - Teil 1: Korrosion metallener Werkstoffe N2 - Innerhalb der Fachausbildung "Kathodischer Korrosionsschutz (KKS)" wurde dieser Vortrag im Grundlagenkurs für erdverlegte Anlagen, Stahlbeton und Innenschutz gehalten. Der 90 min Vortrag befasste sich schwerpunktmäßig mit den Grundlagen der elektrochemischen Korrosion von wichtigen Metallen im Bauwesen: Unleg. Stahl, Aluminium- und Zinkwerkstoffen sowie nichtrostenden Stählen. Galvanische Elemente sowie die Grenzen der elektrochemischen Potentialmessung wurden besprochen. Dies wird anhand einer Reihe von Beispielen verdeutlicht. Der Vortag knüpft die Verbindung zwischen den grundlegenden Korrosionsreaktionen, den äußeren Umgebungsbedingungen, der Korrosionsgeschwindigkeit, dem Faraday'schen Gesetz und den elektrochemischen Stromdichte-Potential-Kurven, mit denen in der Korrosionswissenschaft gearbeitet wird. T2 - Grundlagenkurs für erdverlegte Anlagen, Stahlbeton und Innenschutz; Fachausbildung "Kathodischer Korrosionsschutz (KKS)" CY - Online meeting DA - 28.02.2023 KW - Korrosion KW - Elektrochemische Korrosion KW - Potentialmessung KW - Galvanische Korrosion KW - Bimetallkorroison PY - 2023 AN - OPUS4-57068 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -