TY - JOUR A1 - Tomiak, F. A1 - Schartel, Bernhard A1 - Wolf, M. A1 - Drummer, D. T1 - Particle Size Related Effects of Multi-Component Flame-Retardant Systems in poly(butadiene terephthalate) N2 - Aluminum tris (diethylphosphinate) (AlPi) is known to have an efficient flame-retardant effect when used in poly(butadiene terephthalates) (PBT). Additionally, better flame-retardant effects can be achieved through the partial substitution of AlPi by boehmite in multi-component systems, which have been shown to be an effective synergist due to cooling effects and residue formation. Although the potential of beneficial effects is generally well known, the influence of particle sizes and behavior in synergistic compositions are still unknown. Within this paper, it is shown that the synergistic effects in flammability measured by limiting oxygen index (LOI) can vary depending on the particle size distribution used in PBT. In conducting thermogravimetric analysis (TGA) measurements, it was observed that smaller boehmite particles result in slightly increased char yields, most probably due to increased reactivity of the metal oxides formed, and they react slightly earlier than larger boehmite particles. This leads to an earlier release of water into the system enhancing the hydrolysis of PBT. Supported by Fourier transformation infrared spectroscopy (FTIR), we propose that the later reactions of the larger boehmite particles decrease the portion of highly flammable tetrahydrofuran in the gas phase within early burning stages. Therefore, the LOI index increased by 4 vol.% when lager boehmite particles were used for the synergistic mixture. KW - Flame retardants KW - Aluminum diethylphosphinate KW - Boehmite KW - Poly(butadiene terephthalates) (PBT) KW - Mechanical properties PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-509286 DO - https://doi.org/10.3390/polym12061315 SN - 2073-4360 VL - 12 IS - 6 SP - 1315 PB - MDPI AN - OPUS4-50928 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kruschwitz, Sabine T1 - Challenges in Intelligent Computing for Non destructive testing in civil engineering – today and tomorrow N2 - A large amount of data and information is collected in the field of non-destructive testing (NDT) in civil engineering. The weakly structured data are usually evaluated with regard to specific testing tasks (e.g. geometry determination, damage localization, quality assurance). While the data offers great economic potential, i.e. to support construction planning, monitoring and maintenance processes, the evaluation is manual and case-by-case and therefore too inefficient for broader applications. We present recent visions and approaches how these large amounts of data need to be handled in the future and how we aim to make the acquired knowledge accessible to our stakeholders. Building on initiatives in materials research, we stress the importance of further research in the field of semantic data integration particularly motivate why an ontology is needed for the area of NDT in civil engineering. T2 - EG-ICE 2020 CY - Online meeting DA - 01.07.2020 KW - Data analysis KW - Non destructive testing KW - Computational engineering KW - AI PY - 2020 AN - OPUS4-50971 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Santandrea, A. A1 - Vignes, A. A1 - Krietsch, Arne A1 - Brunello, D. A1 - Perrin, L. A1 - Laurent, A. A1 - Dufaud, O. T1 - Evaluating the explosion severity of nanopowders: International standards versus reality N2 - The maximum explosion overpressure and the maximum rate of pressure rise, which characterize thedust explosion severity, are commonly measured in apparatuses and under specific conditions defined byinternational standards. However, those standards conditions, designed for micropowders, may not befully adapted to nanoparticles. Investigations were conducted on different nanopowders (nanocellulose,carbon black, aluminum) to illustrate their specific behaviors and highlight the potential inadequacyof the standards. The influence of the sample preparation was explored. Various testing procedureswere compared, focusing on the dust cloud turbulence and homogeneity. Dust dispersion experimentsevidenced the importance of the characterization of the dust cloud after dispersion, due to the frag-mentation of agglomerates, using metrics relevant with nanoparticles reactivity (e.g. surface diameterinstead of volume diameter). Moreover, the overdriving phenomenon (when the experimental resultsbecome dependent of the ignition energy), already identified for micropowders, can be exacerbated fornanoparticles due to their low minimum ignition energy and to the high energy used under standardconditions. It was evidenced that for highly sensitive nanopowders, pre-ignition phenomenon can occur.Finally, during severe explosions and due to a too long opening delay of the ‘fast acting valve’, the flamecan go back to the dust container. KW - Dust explosions KW - Gas explosions KW - Minimum ignition temperature KW - Hybrid mixtures PY - 2020 DO - https://doi.org/10.1016/j.psep.2020.04.011 VL - 138 SP - 279 EP - 291 PB - Elsevier B.V. AN - OPUS4-50944 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. T1 - Aerial Robot Olfaction - A Summary and Survey from BAM Perspective N2 - This presentation gives an introduction to the gas-sensitive aerial robots developed at BAM, including various application examples in the field of mobile robot olfaction: gas source localization and gas distribution mapping. T2 - Harvard University School of Engineering and Applied Sciences (SEAS)/Earth and Planetary Sciences (EPS) - Martin Group Seminar CY - Online meeting DA - 11.06.2020 KW - Mobile Robot Olfaction KW - Localization of gas sources KW - UAV KW - Tomographic reconstruction of gas plumes KW - Tunable Diode Laser Absorption Spectroscopy (TDLAS) PY - 2020 AN - OPUS4-50916 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Palis, Stephan A1 - Sträubig, Felix A1 - Voigt, Sascha A1 - Knaust, Christian T1 - Experimental investigation of the impact of water mist on high-speed non-premixed horizontal methane jet fires N2 - In this paper, the influence of a fixed water mist firefighting system on a high-speed non-premixed horizontal methane jet fire is investigated with focus on its effect on temperatures and heat load of the jet fire and on ist surroundings. Six tests are performed in which gas is released out of an orifice with a diameter of 1 mm and a release pressure of up to 186 bar. In addition to temperature and radiation measurements, the release pressure, gas mass flow rate and exhaust gas concentrations are detected to determine the heat release. Video and IRanalysis are used to evaluate the interactions between jet fire and water mist. The experiments show, that water mist reduces the temperatures inside the jet fire flow field and its radiative heat flux. It can lower the Risk of ignition of adjacent surfaces and materials, as temperatures fall below autoignition temperatures of common materials like plastics. Although water mist does not extinguish the fire, it has an impact on the energy release by reducing combustion efficiency due to heat exchange with the water mist and oxygen displacement. KW - Fixed firefighting system KW - Jet fire KW - Water mist KW - Fire test KW - Methane KW - Supersonic flow PY - 2020 DO - https://doi.org/10.1016/j.firesaf.2020.103005 VL - 114 SP - 103005 PB - Elsevier Ltd. AN - OPUS4-50963 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häßler, Dustin A1 - Mund, M. T1 - Bewertung des Feuerwiderstandes von Stahlkonstruktionen mit reaktiven Brandschutzsystemen unter Berücksichtigung des Alterungsverhaltens N2 - Vorstellung des Arbeitsstands im Projekt 20470N (BAM Vh 7350). T2 - 98. Sitzung des Arbeitsausschusses Brandschutz CY - Hamburg, Germany DA - 09.11.2018 KW - Reaktive Brandschutzsysteme KW - Dauerhaftigkeit KW - Brandschutz KW - Stahl PY - 2018 AN - OPUS4-49793 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epple, Niklas T1 - Monitoring of bridges with coda waves - first steps towards an imaging strategy N2 - Monitoring of concrete structures is of utmost importance in maintenance and preservation of infrastructure. As a part of the DFG research group CoDA (Concrete Damage Assessment by Coda Waves), the works within this PhD project aim for identification of damage sensitive parameters extracted from ultrasonic measurements obtained with embedded sensors, the determination of environmental (reversible) influences on the signal and the localisation of damaged areas. The main technique used for the detection of changes in the monitored material is the so-called Coda Wave Interferometry (CWI). It uses the later part of the ultrasonic recording for the detection of small changes in the sensed area and the calculation of a relative velocity change. Using this technique we can show that we are able to detect changes in concrete temperature with ultrasound measurements. This enables temperature correction for ultrasound monitoring with embedded sensors. The crucial point for imaging and localisation with coda waves is the calculation of the so-called sensitivity kernels. We propose the application of numerical wave simulations for the kernel calculations instead of the commonly used diffusivity equation. Using finite-difference wave modelling code from our DFG project partners we are able to calculate those Kernels and first results are shown in this presentation. The major task for the second year will be the development and implementation of the inversion algorithm as well as the preparation of validation experiments. T2 - Doktorandenseminar BAM Abt. 8 CY - Berlin, Germany DA - 30.03.2020 KW - Ultrasound KW - Non-destructive testing KW - Numerical modelling KW - Structural health monitoring PY - 2020 AN - OPUS4-50624 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Wosniok, Aleksander ED - Werneck, M.M. ED - da Silva Barros Allil, R.C T1 - POF Sensors for Structural Health Monitoring N2 - The ever more ambitious strategic goals of meeting the requirements in ensuring technical safety and security of civil structures have resulted in flourishing development of innovative structural health monitoring (SHM) technologies for early damage diagnosis and prognosis. At the same time, implementing SHM systems provides tangible economic benefits derived from lower life-cycle costs associated with reduction in the maintenance, repair and insurance expenses. Due to the large size and harsh environmental conditions common to most civil structures, the broad range of favorable physical-mechanical properties of POFs allow for customized monitoring solutions for a wide variety of applications. In addition to common SHM-related advantages of optical fibers including their electromagnetic immunity, small size, lightweight as well as spark-free and non-conductive characteristics, POFs offer better bending and fracture resistance then their glass-counterparts. Particularly, the improved robustness of POFs, their ease of handling, low Young’s Modulus and high elastic limit of 10% compared to 1% in silica glass [1] are relevant to practical applications. Depending on the composition, dopants, drawing process and geometry [2], strain measurement up to 45% [3] or even above 100% [4,5] has been demonstrated with standard POFs. Therefore, the dominant market expected for POF sensors includes monitoring of high-strain-rate deformations in earthwork structures, crack detection in concrete and masonry structures [6] or overstressing in high-rise steel structures exposed to moisture, corrosion, leakage, fatigue, vibration, fire, overflow, earthquake and intentional damage. For fracture monitoring within concrete structures, the sensory usage of POFs becomes especially favorable since the extremely alkaline environment of concrete mixtures is well known to be corrosive to standard silica glass optical fibers (GOFs) [1,7]. Most of advanced distributed sensing techniques are commonly based on Rayleigh backscatter reflectometry using commercially available multimode (MM) POFs. Such typical MM POFs range from a step-index (SI) poly(methyl methacrylate) (PMMA) POF having a core diameter of 1 mm to a low-loss graded-index (GI) perfluorinated (PF) POF based on poly(perfluorobutenyl-vinylether) also known as CYTOP [8] with a 50 µm core diameter. The relatively low optical attenuation value of 30 dB/km at 1.3 µm [9,10] makes PFGI POFs also interesting for distributed Brillouin sensing [11-14]. Compared to GOFs, PFGI POFs offer better potential for temperature measurement and have comparably low theoretical attenuation limit [15]. Therefore, POF-based distributed Brillouin sensing is expected to play an important role in the future of SHM, especially at high-strain ranges. The significance of the Brillouin measurment technique can be also enhanced by further development of the single-mode (SM) POFs which are still subject of research and are used for coherent detection techniques [6]. Furthermore, SM PMMA POFs have been characterized in a Mach-Zehnder interferometer setup for strain values up to 15.8% [16,17]. The current development of SM perfluorinated and microstructured POFs (mPOFs) represents an immense promise for quasi-distributed dynamic measurement at high strain levels based on fiber Bragg grating (FBG) technology. While SM mPOFs with optical losses of about 1 dB/m can be fabricated [6], the SM PF POFs presented by Zhou et al. feature low attenuation of even less than 0.2 dB/m in the wavelength range of 1.41 µm to 1.55 µm [18]. At the same time, the SM PF POFs have the potential for improved thermal stability compared to their PMMA counterparts [19]. This whole chapter provides a comprehensive overview on current POF-based sensing principles and SHM technologies, highlighting their diverse applications in civil engineering structures. In the application-related context, close attention is paid to the development of smart sensor-based geotextiles and geogrids. Such geosynthetics-integrated distributed POF sensors have proven to be a promising solution for two- or even tree-dimensional monitoring of critical high mechanical deformations in both geotechnical and masonry structures. Moreover, geosynthetics in the form of nonwoven geotextiles as well as polymer-based geogrids used as carrier materials for POF sensors enable optimized load transfer from the monitored structure to the measuring fiber without losing their original functionality. In other words, smart geosynthetics provide a cost-efficient dual solution for, on the one hand, well-established increase of structure stability and decrease of erosion effects, on the other hand, early-warning and detection capabilities in the prevention and elimination of potential hazards and lasting damages. KW - Plastic Optical Fiber Sensor KW - OTDR KW - Brillouin Sensing KW - Interferometric Sensor KW - FBG KW - Long Period Grating KW - Smart Geosynthetics PY - 2020 SN - 978-1-13829-853-8 SP - 267 EP - 283 PB - CRC Press Taylor & Francis Group CY - Boca Raton, FL, USA AN - OPUS4-50561 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mundra, Shishir A1 - Prentice, D. P. A1 - Bernal, S. A. A1 - Provis, J. L. T1 - Modelling chloride transport in alkali-activated slags N2 - The service-life of steel-reinforced concrete structures is primarily determined by the ability of the concrete cover to resist chloride ingress. With limited literature available on the ingress of chloride into alkali-activated slags (AAS) under service conditions, it is critical that this is described by appropriate models. This paper describes an interactive software framework to relate chloride ingress into AAS with the chemistry of the concrete cover, by considering the chloride binding capacity and porosity of the binder as a function of time, based on thermodynamic calculations of the phase assemblage as a function of slag and activator composition. This provides a major step towards developing the ability to predict the ingress of chlorides in alkali-activated concretes from a sound theoretical basis, which is essential in providing confidence in the durability of these materials in essential infrastructure applications. KW - Thermodynamic calculations KW - Alkali activated cement KW - Durability KW - Diffusion KW - Chloride PY - 2020 DO - https://doi.org/10.1016/j.cemconres.2020.106011 VL - 130 SP - 106011 PB - Elsevier Ltd. AN - OPUS4-50423 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander T1 - Multifunktionale Geokunststoffe - nachhaltige Zustandsüberwachung durch ortsaufgelöste faseroptische Sensoren N2 - Vorstellung von Entwicklungsarbeiten zum Thema sensorbasierte Geokunststoffe mit integrierten faseroptischen Sensoren. T2 - 14. Bautextilien-Symposium BAUTEX 2020 CY - Chemnitz, Germany DA - 29.01.2020 KW - Intelligente Geokunststoffe KW - Sensorbasierte Geokunststoffe KW - Faseroptischer Sensor KW - Ortsverteilter Sensor PY - 2020 AN - OPUS4-50321 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Morys, Michael A1 - Häßler, Dustin A1 - Krüger, Simone A1 - Schartel, Bernhard A1 - Hothan, Sascha T1 - Beyond the standard time-temperature curve: Assessment of intumescent coatings under standard and deviant temperature curves N2 - Nowadays there are intumescent coatings available for diverse applications. There is no established assessment of their protection performance besides the standard time-temperature curve, but natural fire scenarios often play an important role. A reliable straightforward performance-based assessment is presented. The effective thermal conductivity per thickness is calculated based on intermediate-scale fire tests. The optimum thermal insulation, the time to reach it, and the time until contingent failure of the coating are used for an assessment independent of the heating curve. The procedure was conducted on four different commercially intumescent coatings for steel construction, one solvent-based, one waterborne, one epoxy-based, and a bandage impregnated with a waterborne coating. The performance was studied under four different but similar shaped heating curves with different maximum temperatures (standard time-temperature curve, hydrocarbon curve and two self-designed curves with reduced temperature). The thermal protection performance is crucially affected by the residue morphology. Therefore, a comprehensive morphology analysis, including micro-computed tomography and scanning electron microscopy, was conducted on small-scale residues (7.5 x 7.5 cm2). Two different types of inner structures and the residue surface after different heat exposures were discussed in terms of their influence on thermal protection performance. KW - Intumescence KW - Coating KW - Computed tomography KW - Small scale KW - Heating curves KW - Residue morphology PY - 2020 DO - https://doi.org/10.1016/j.firesaf.2020.102951 SN - 0379-7112 VL - 112 SP - 102951 PB - Elsevier Ltd. AN - OPUS4-50334 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Martin A1 - Wu, Dejian A1 - Zhao, P. A1 - Tan, X. A1 - Huang, W. A1 - Qianc, X. T1 - Minimum explosion concentrations of coal dusts with CH4/H2/CO below the gas lower explosion limit N2 - A 20-L spherical explosion chamber was used to investigate the explosion characteristics of dust clouds in air with the presence of flammable gas which is lower than its lower explosion limit (LEL). including minimum explosion concentration (MEC) of dust. Explosion pressure (Pex) and explosion pressure rise (dp/dt)ex). Two dust samples (anthracite coal, bituminous coal) and were three flammable gases (CH4, H2 and CO) were tested. Experimental results showed that the explosion of hybrid mixtures occurs when both dust and gas concentrations are lower than the LEL/MEC of the single substances. Meanwhile. all flammable gases with different volume fractions have distinct effects on the MEC. Pex and (dp/dt)ex of the dust samples. With the increase of the flammable gas concentration. either the Pex and (dp/dt)ex increase or the MEC decreases for all the hybrid mixtures of both two dust samples. At the same concentration of coal dusts. the addition of CH4 promotes higher explosion risks than the other two flammable gases. The distribution of (dp/dt)ex is quite different with the restricted area defined by empirical formulas. These results improve our understanding of the explosion behaviour and the explosion risk of hybrid dust-gas mixtures in air. KW - Dust explosions KW - Gas explosions KW - Minimum explosible concentration KW - Lower explosion limit KW - Hybrid mixtures PY - 2020 DO - https://doi.org/10.1016/j.fuel.2019.116401 SN - 0032-5910 VL - 260 SP - UNSP 116401 PB - Elsevier Sci. Ltd. AN - OPUS4-49956 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Szypkowski, Marko ED - Bartmann, H. T1 - Taucher-Handbuch, Technik, Tauchgeräte- Bauteile und Baugruppen für Leichttauchgeräte, Kap. Flaschenventile N2 - Darstellung der Gefahren und und Hinweis auf die anzuwendenden Normen bei der Wartung bei Sauerstoffventilen im Bereich des Atemschutz KW - Atemschutz KW - Gasflaschenventil KW - Sauerstoff PY - 1993 SN - 978-3-609-75380-5 VL - 2020 SP - 51 EP - 51 PB - Storck Verlag CY - Landsberg am Lech ET - 108 AN - OPUS4-50827 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wu, Dejian A1 - Schmidt, Martin A1 - Tan, X. A1 - Zhao, P. A1 - Huang, W. A1 - Qian, X. T1 - Minimum ignition temperature of carbonaceous dust clouds in air with CH4/H-2/CO below the gas lower explosion limit N2 - Godbert-Greenwald furnace was used to investigate the minimum ignition temperature of dust clouds (MITC) in air with the presence of flammable gas which is lower than its lower explosion limit (LEL). Three flammable gases (CH4, H2 and CO) and three carbonaceous dusts (anthracite coal, bituminous coal and sweet potato starch) were tested. Results showed that all flammable gases have distinct effects on the MITC of the dust samples and volatile matter content of dust plays an important role during the ignition process. Specifically, the MITC of anthracite coal dust decreased from 610 °C to 560 °C, 580 °C and 570 °C with 3% CH4, 3% CO and 2.5% H2, respectively. Moreover, a heterogeneous ignition mechanism model was proposed to verify the equally global ignition characteristic between hybrid anthracite coal-CxHy mixture and bituminous coal. All three gases had an ignorable effect on the MITC of starch dust considering the experimental error. The presence of CO and H2 slightly promoted the ignition of bituminous coal dust, but the addition of CH4 showed a distinct concentration effect on the MITC of bituminous coal: the MITC decreased with 1% CH4 while increased with 2% and 3% CH4. This negative-effect of flammable gases at such low concentrations on ignition temperature of bituminous coal dusts was found for the first time. Furthermore, the presence of the 2nd flammable gas had a smaller effect on the MITC of dust samples with a higher volatile content, resulted from the competition of heterogeneous and homogeneous ignition mechanisms. KW - Dust explosions KW - Gas explosions KW - Minimum ignition temperature KW - Hybrid mixtures PY - 2020 DO - https://doi.org/10.1016/j.fuel.2019.116811 SN - 0016-2361 VL - 264 SP - 116811 PB - Elsevier Ltd. AN - OPUS4-50856 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mietz, Jürgen A1 - Burkert, Andreas T1 - Selection and Durability of Stainless Steels for Civil Engineering N2 - Due to the large number of stainless steels with different chemical composition and different microstructure the selection of the suitable material represents a huge challenge. In order to facilitate the appropriate grade selection, in the current European standard EN 1993-1-4 a procedure is defined based on the use of a look-up table considering the key variables that influence the selection of stainless steels. The table uses descriptions that competent designers should be able to readily understand or define without prior knowledge. The output from the look-up table is used to select alloys based on a Corrosion Resistance Class (CRC) from I to V. The advantage of this approach is that the designer simply specifies the relevant CRC and does not need to consider in detail which of the many (very similar) alloys to specify. KW - Corrosion resistance KW - Stainless steel KW - Civil engineering KW - Atmospheric corrosion PY - 2020 DO - https://doi.org/10.4028/www.scientific.net/KEM.843 SN - 1662-9795 VL - 843 SP - 125 EP - 131 PB - Trans Tech Publications Ltd, CY - Switzerland AN - OPUS4-50831 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Moosavi, Robabeh A1 - Grunwald, Marcel A1 - Redmer, Bernhard T1 - Crack detection in reinforced concrete N2 - Automatic segmentation of cracks using crack detection methods fails when applied on concrete with embedded reinforcements; it results in artifacts called false-detected cracks. We present a two-step approach to trace the cracks which reduces significantly detecting the false ones. In the first step, the reinforcements were found and removed from the 3D data set, and in the second step, the cracks were detected in the 3D data set free from reinforcements. To visualize and determine the structure and the degree of damages nondestructively, planar tomography as a special case of laminography was used. KW - 3D imaging KW - Laminography KW - Crack detection KW - Reinforced concrete PY - 2020 DO - https://doi.org/10.1016/j.ndteint.2019.102190 VL - 109 SP - 102190 PB - Elsevier Ltd. AN - OPUS4-49520 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wilrich, Thomas A1 - Wilrich, Cordula T1 - Vergiftungstod bei Motorbootreinigung N2 - Ein Praktikant atmete bei Reinigungsarbeiten Dämpfe des verwendeten Reinigungsmittels ein, fiel in Ohnmacht und verstarb. Der Meister, der den Praktikanten mit dieser Tätigkeit beauftragt hatte, wurde wegen fahrlässiger Tötung durch Verstöße gegen das Jugendarbeitsschutz- und Gefahrstoffrecht verurteilt. Dieser Aufsatz bereitet die wesentlichen Aussagen des Urteils auf – und erläutert auch die Fehler gemäß Gefahrstoffverordnung (GefStoffV), die das Gericht nicht anspricht. KW - Arbeitsschutz KW - Gefährdungsbeurteilung KW - Gefahrstoffverordnung KW - Schutzmaßnahmen KW - Substitution PY - 2020 SN - 2698-3710 VL - 1 IS - 1 SP - 29 EP - 31 PB - Verlag C.H.BECK oHG CY - München AN - OPUS4-50455 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Flammschutz für technische Kunststoffte für elektronische Anwendungen N2 - Das Brandverhalten stellt wie das ausgezeichnete elektrische Isolationsverhalten, die geringen elektrischen Verluste, die Verarbeitbarkeit und Formbarkeit eine der wesentlichen Schlüsseleigenschaften im Eigenschaftsprofil von Polymerwerkstoffen in der Elektronik und der Elektrotechnik dar. Dabei bedarf es einer Ausrüstung der Polymerwerkstoffe mit Flammschutzmittel. Die Entwicklung von immer effizienteren, synergistischen und multifunktionalen Multikomponentensystemen ist dabei eine herausragende Quelle für Innovation. Die Entwicklung und Verbesserung der werkstoff- und anwendungsspezifischen Flammschutzlösungen bestimmen die aktuellen und zukünftigen Polymermaterialien in der Elektronik und Elektrotechnik mit. Der Vortrag stellt anhand von Beispielen einige der erfolgreichen Konzepte dar. Es wird versucht, über das wissenschaftlich-systematische Verständnis Grundprinzipien und vielversprechende Lösungsstrategien zu verdeutlichen. T2 - Kunststoff trifft Elektronik, KUZ Kunststoffzentrum in Leipzig CY - Leipzig, Germany DA - 29.01.2020 KW - Flame retardant KW - Ssynergy KW - Flame retardant mode of action KW - UL 94 KW - Cone calorimeter PY - 2020 AN - OPUS4-50495 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. T1 - Gassensitive Flugroboter der BAM T1 - Aerial robot olfaction @ BAM N2 - Der Vortrag gibt Beispiele dafür, wie Drohnen sinnvoll im zivilen Bereich eingesetzt werden können. Insbesondere werden die Lokalisierung von Gasemissionsquellen und die Erstellung von Gasverteilungskarten vorgestellt. T2 - InnoTesting2020 „Innovative Ideen - neue Testmethoden” CY - Wildau, Berlin, Germany DA - 27.02.2020 KW - Mobile Robot Olfaction KW - Erstellung von Gasverteilungskarten KW - Lokalisierung von Gasemissionsquellen KW - UAV / UAS PY - 2020 AN - OPUS4-50476 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rai, Alena T1 - Volumetrische Ansprache von Grindingoberflächen N2 - Seit einigen Jahren steht die Oberflächentexturierung der Betonfahrbahndecken mittels Grinding im Fokus der Forschung und Entwicklung des Betonstraßenbaus. Dabei wird das Ziel verfolgt, Grindingtechnologie zeitnah in das deutsche Regelwerk einzuführen und gegebenenfalls die Regelbauweise Waschbeton dadurch zu ersetzen. Im Rahmen der systematischen Erprobung konnte festgestellt werden, dass es, bedingt durch Beanspruchungen während der Nutzungsphase, zur Verbesserung bzw. Verschlechterung der relevanten Oberflächenperformances, wie z.B. Griffigkeit, Ebenheit oder Geräuschpegel kommt. Dies wird gegenwärtig mit den Texturgeometrieveränderungen in Verbindung gebracht. Vor diesem Hintergrund stellt sich zunächst die Frage, in wie weit die Grindingtextur und deren Veränderungen messtechnisch erfasst werden können und welche statistischen Kenngrößen dabei abgeleitet werden können. In diesem Zusammenhang ist eine Evaluation der dreidimensionalen messtechnischen Ansprache von Grindingoberflächen notwendig. Perspektivisch bedarf es einer Korrelationsanalyse zwischen der o.g. Texturkenngrößen mit Veränderungen der Oberflächenperformances. Dieser Beitrag zeigt, dass mithilfe eines auf Streifenlichtprojektion basierenden Messsystems, eine hochaufgelöste volumetrische Erfassung der Oberflächentopografie verschiedener Grindingtexturen sowohl im Labor als auch in situ möglich ist. Darauf aufbauend galt es, die messtechnischen Voraussetzungen zur Gewährleistung reproduzierbarer Messungen zu schaffen. Dies ermöglicht eine Dokumentation der zeitlichen Texturveränderungen infolge verschieden-artiger Beanspruchungen. Basierend auf den Ergebnissen der 3D-Texturerfassung wurden Auswerteroutinen zur quantitativen und statistischen Charakterisierung der Oberflächentextur entwickelt. Zusätzlich wurden diese angewandt, um exemplarisch die Veränderungen der Oberflächentopographie infolge klimatischer Beanspruchung quantitativ abzubilden. T2 - Workshop Grinding CY - Bergisch Gladbach, Germany DA - 28.01.2020 KW - Betonfahrbahndeckentexturen KW - Grinding KW - 3D-Texturerfassung KW - Streifenlichtprojektionssystem PY - 2020 AN - OPUS4-50449 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Zur Berechnung der Erschütterungsminderung von Eisenbahngleisen mit ein- und zweidimensionalen Modellen N2 - Eindimensionale Modelle des Gleises aus einem Schienenstützpunkt, zweidimensionale Modelle enthalten die Kraftverteilung der Schiene. Eindimensionale Modelle machen einen Fehler, weil sie eine zu große Fahrzeugmasse berücksichtigen. Man kann jedoch bei der Berechnung der Minderungswirkung von Gleiselementen eindimensionale Gleismodelle verwenden, um die Kraftübertragung des Gleises bzw. die Minderungswirkung des Gleises zu berechnen. Die Wechselwirkung mit dem Fahrzeug kann einfach mit der dynamischen Stützpunktsteifigkeit berechnet werden. Dabei muss die Stützpunktsteifigkeit mit einer charakteristischen Gleislänge multipliziert werden, die frequenz- und systemabhängig ist. T2 - Norm-Arbeitsausschuss Schwingungsminderung in der Umgebung von Verkehrswegen CY - Munich, Germany DA - 14.01.2020 KW - Richtige Fahrzeugmasse KW - Erschütterungsminderung KW - Elastische Gleiselemente KW - Rechenverfahren PY - 2020 AN - OPUS4-50268 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wilrich, Cordula A1 - Wilrich, Thomas T1 - Explosion bei Reinigungsarbeiten mit Ethanol im Schulunterricht N2 - Für die Reinigung ihres Klassenzimmers von Klebstoffresten, Schmierereien u. ä. am Ende des Schuljahres verwendeten die Schüler einen 20 l-Blechkanister mit Lösemittel (Ethanol bzw. Spiritus für Matrizendrucker), der als leichtentzündlich gekennzeichnet war. Die Entnahme des Lösemittels durch die Schüler erfolgte durch vorsichtiges Kippen des in einem Regal stehenden Kanisters nach vorne, so dass Lösemittel auf die für die Reinigung verwendeten Papiertücher tropfte. Am 23. Juni 1997 kam es unter Bildung einer Stichflamme zur Entzündung verschütteten Ethanols und in der Folge auch zum Bersten des Behälters. In der Folge des Unfalls verstarb eine Schülerin und acht weitere Schülerinnen und Schüler wurden zum Teil schwerstverletzt. Zudem entstand infolge des Brandgeschehens erheblicher Sachschaden. Dieser Aufsatz stellt das Strafurteil gegen den verantwortlichen Lehrer vor und diskutiert die relevanten, aber im Urteil nicht benannten Anforderungen des Gefahrstoffrechts. KW - Explosion KW - Explosionsschutz KW - Gefahrstoffverordnung KW - Gefährdungsbeurteilung KW - Schutzmaßnahmen KW - Substitution PY - 2020 DO - https://doi.org/10.37307/j.2365-7634.2020.01.11 SN - 2365-7626 SN - 2365-7634 (eJournal) IS - 1 SP - 43 EP - 46 PB - Erich Schmidt Verlag (ESV) CY - Berlin AN - OPUS4-50269 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Schartel, Bernhard A1 - Kebelmann, Katharina ED - Hu, Y. ED - Wang, X. T1 - Fire testing for the development of flame retardant polymeric materials N2 - Flame retarded polymeric materials are used in various applications in which a certain fire behavior is demanded. Protection goals are defined, such as limited flammability in terms of hindered sustained ignition or limited contribution to a fire, and these protection levels are tested with defined specimens or components in defined fire scenarios, that is to say, different fire tests. Passing a specific fire test by meeting whatever its demands is often the most important development goal, so the parameters of the different fire tests vary widely to emphasize different fire properties. Some fire tests are used to screen or provide a general assessment of flame retardant polymers during development, while other fire tests and tailored experiments are performed to address special phenomena or understand the flame retardancy modes of action. For all fire testing, the devil is in the details – demanding know-how and crucial efforts to manage the quality of investigations and advanced interpretation. This chapter aims to offer a structured overview of all these aspects. KW - Fire testing KW - Flame retardant KW - Fire retardant KW - Flammability KW - Ignition KW - Oxygen index KW - Cone calorimeter KW - UL 94 KW - Developing fire KW - Uncertainty KW - Fire resistance PY - 2020 SN - 978-1-138-29578-7 SP - 35 EP - 55 PB - CRC Press AN - OPUS4-50236 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Battig, Alexander A1 - Markwart, J. C. A1 - Wurm, F. R. A1 - Schartel, Bernhard T1 - Sulfur's role in the flame retardancy of thio-ether–linked hyperbranched polyphosphoesters in epoxy resins N2 - Hyperbranched polyphosphoesters are promising multifunctional flame retardants for epoxy resins. These polymers were prepared via thiol-ene polyaddition reactions. While key chemical transformations and modes of actions were elucidated, the role of sulfur in the chemical composition remains an open question. In this study, the FR-performance of a series of phosphorus-based flame retardant additives with and without sulfur (thioethers or sulfones) in their structure are compared. The successful synthesis of thio-ether or sulfone-containing variants is described and verified by 1H and 31P NMR, also FTIR and MALDI-TOF. A decomposition process is proposed from pyrolytic evolved gas analysis (TG-FTIR, Py-GC/MS), and flame retardancy effect on epoxy resins is investigated under pyrolytic conditions and via fire testing in the cone calorimeter. The presence of sulfur increased thermal stability of the flame retardants and introduced added condensed phase action. Likely, Sulfur radical generation plays a key role in the flame-retardant mode of action, and sulfones released incombustible SO2. The results highlight the multifunctionality of the hyperbranched polymer, which displays better fire performance than its low molar mass thio-ether analogue due to the presence of vinyl groups and higher stability than its monomer due to the presence of thio-ether groups. KW - Phosphoester KW - Hyperbranched KW - Sulfur KW - Thio-ether KW - Flame retardant KW - Epoxy resin PY - 2020 DO - https://doi.org/10.1016/j.eurpolymj.2019.109390 SN - 0014-3057 VL - 122 SP - 109390 PB - Elsevier Ltd. AN - OPUS4-50238 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Turski Silva Diniz, Analice A1 - Huth, Christian A1 - Schartel, Bernhard T1 - Dripping and decomposition under fire: Melamine cyanurate vs. glass fibres in polyamide 6 N2 - Manipulating the melt dripping of thermoplastics makes a fire scenario more or less dangerous. Yet, a detailed understanding of this phenomenon has remained a question mark in studies of the flammability of plastics. In this work, the individual and collective impacts of additives on the dripping behaviour of polyamide 6 (PA6) were studied. A set of materials compounded with melamine cyanurate (MCA) and glass fibre (GF) was investigated. Under UL 94 vertical test conditions, the dripping during first and second ignition was quantified and investigated in detail. The number, size and temperature of the drops were addressed, and the materials and their drops evaluated with respect to such aspects as their averaged molecular weight, thermal decomposition and rheological properties. PA6 with V-2 classification improved to V-0 with the addition of MCA, and achieved HB in the presence of GF. PA6/GF/MCA achieved V-2. Non-flaming drops of PA6/MCA consisted of oligomeric fragments. Flaming drops of PA6/GF showed a more pronounced decomposition of PA6 and an increased GF content. The dripping behaviour of PA6/GF/MCA can be understood as a combination of the influence of both additives. The results showed nicely that dripping under fire is neither a straightforward material property nor a simple additive influence, but the complex response of the material influenced by the interaction and competition of different phenomena. KW - Dripping KW - UL 94 KW - Polyamide 6 KW - Melamine cyanurate KW - Glass fibre KW - Flame retardant PY - 2020 DO - https://doi.org/10.1016/j.polymdegradstab.2019.109048 SN - 0141-3910 VL - 171 SP - 109048 PB - Elsevier Ltd. AN - OPUS4-50239 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kowarik, Stefan A1 - Hussels, Maria-Teresa A1 - Chruscicki, Sebastian A1 - Münzenberger, Sven A1 - Lämmerhirt, A. A1 - Pohl, P. A1 - Schubert, M. T1 - Fiber Optic Train Monitoring with Distributed Acoustic Sensing: Conventional and Neural Network Data Analysis N2 - Distributed acoustic sensing (DAS) over tens of kilometers of fiber optic cables is well-suited for monitoring extended railway infrastructures. As DAS produces large, noisy datasets, it is important to optimize algorithms for precise tracking of train position, speed, and the number of train cars, The purpose of this study is to compare different data analysis strategies and the resulting parameter uncertainties. We present data of an ICE 4 train of the Deutsche Bahn AG, which was recorded with a commercial DAS system. We localize the train signal in the data either along the temporal or spatial direction, and a similar velocity standard deviation of less than 5 km/h for a train moving at 160 km/h is found for both analysis methods, The data can be further enhanced by peak finding as well as faster and more flexible neural network algorithms. Then, individual noise peaks due to bogie clusters become visible and individual train cars can be counted. From the time between bogie signals, the velocity can also be determined with a lower standard deviation of 0.8 km/h, The analysis methods presented here will help to establish routines for near real-time Train tracking and train integrity analysis. KW - Artificial neural networks KW - Distributed fiber optic sensing KW - Distributed acoustic sensing KW - Train tracking PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-502872 DO - https://doi.org/10.3390/s20020450 VL - 20 IS - 2 SP - 450 PB - MDPI CY - Basel, Switzerland AN - OPUS4-50287 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Characteristics of train passages over slab tracks from measurements and different track-soil models - Damage detection and ground vibration reduction N2 - The train passages over intact or damaged slab tracks on different soils have been calculated by the finite-element boundary-element or the wavenumber-domain method. The influence of track and soil parameters on the distribution of the track displacements and the soil forces has been analysed. The measured and calculated displacement time histories of train passages could be used to identify track damages such as lose sleepers or a lose track plate. The time histories and spectra of the soil forces can explain the measured ground vibration reduction of slab tracks. The calculated displacement and force distributions of slab tracks on continuous soils do not fulfil the Winkler hypothesis and Winkler models should not be used for track analysis. KW - Wavenumber domain KW - Continuous soil KW - Slab track KW - Soil forces KW - Track displacements KW - Track filter KW - Vehicle–track interaction PY - 2020 DO - https://doi.org/10.1177/0954409719835036 SN - 0954-4097 VL - 234 IS - 2 SP - 142 EP - 160 PB - Sage CY - London AN - OPUS4-50266 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Hauswaldt, Sebastian T1 - Kontinuumsmechanische Werkstoffmodelle zur numerischen Simulation von Stahlbauteilen im Brandfall N2 - Das nichtlineare und geschwindigkeitsabhängige Materialverhalten von Stahl wird besonders bei hohen Temperaturen sichtbar. Für Finite-Elemente-Simulationen von Stahlkonstruktionen im Brandfall sollte aus diesem Grund plastisches und geschwindigkeitsabhängiges Materialverhalten beschrieben werden. Die vorliegende Arbeit betrachtet unter diesem Aspekt bisherige Materialuntersuchungen und macht Vorschläge für dreidimensionale Materialmodelle mit entsprechenden Eigenschaften. Es werden zunächst die phänomenologischen Eigenschaften von Baustahl anhand einer Literaturrecherche analysiert, wobei verstärkt auf Untersuchungen des Materialverhaltens bei Belastungen und Aufheizprozessen, wie sie im Brandfall zu erwarten sind, geachtet wird. Die für die Bemessung von Stahlkonstruktionen gebräuchliche Spannungsbeschreibung des EC 3-1-2 wird untersucht. Es werden ihre Stärken, aber auch die zur Entwicklung einer kontinuumsmechanischen Materialformulierung fehlenden Eigenschaften, aufgezeigt. Ein nichtlinear-elastisches kontinuumsmechanisches Materialmodell der Deformationstheorie der Plastizität wird so angepasst, dass es die Spannungs-Dehnungslinien gemäß EC 3-1-2 im einachsigen Spannungszustand beschreibt. Es wird des Weiteren ein thermoelastisch-viskoplastisches Modell vorgestellt, das in der Lage ist, Kriechen und Relaxation bei Aufheiz- und Abkühlprozessen zu beschreiben. Die Struktur dieses Materialmodells wird so gewählt, dass die Parameter an hierfür geeigneten Messergebnissen leicht identifiziert werden können. Der deviatorische Anteil des Modells besteht aus einem geschwindigkeitsunabhängigen, plastischen Anteil und einem geschwindigkeitsabhängigen, viskoelastischen Anteil. Der geschwindigkeitsunabhängige, plastische Anteil wurde als Differentialgleichung auf Grundlage der so genannten endochronen Plastizitätstheorie formuliert. Die Parameter der Materialmodelle werden auf Grundlage der Messergebnisse stationärer Warmzugversuche an Baustahlproben identifiziert. Sowohl das nichtlinear-elastische EC 3-1-2-Materialmodell als auch das thermoelastisch-viskoplastische Materialmodell mit den an Baustahl angepassten Materialparametern wird numerisch für die Verwendung mit Finite-Elemente-Programmen aufbereitet und als UMAT-Subroutine für ABAQUS in der Programmiersprache FORTRAN implementiert. Hierbei wird insbesondere auf die Bereitstellung der konsistenten Tangentenoperatoren Wert gelegt, um eine effiziente numerische Berechnung bei Verwendung der Materialmodelle zu ermöglichen. Abschließend werden erste Simulationsrechnungen vorgestellt, um beispielhaft die Möglichkeiten der Anwendung der entwickelten und implementierten Materialmodelle für Simulationen von Stahlkonstruktionen im Brandfall aufzuzeigen. N2 - The non-linear and rate-dependent material behaviour of steel becomes particularly visible at high temperatures. For finite-element-simulations of steel structures in the event of fire, plastic and rate- dependent material behaviour should therefore be described. With this in mind, this thesis looks at previous material investigations and makes suggestions for three-dimensional material models with the corresponding properties. The phenomenological properties of structural steel are analysed on the basis of a literature study, whereby increased attention is paid to the material behaviour under loads and heating processes, as can be expected in the event of fire. The stress-strain-relation of the EC 3-1-2 used for the design of steel structures is examined. The advantages of this description, but also the missing properties for the development of a continuum-mechanical material formulation, are shown. A non-linear-elastic continuum mechanical material model of the deformation theory of plasticity is adapted in such a way that it describes the stress-strain curves according to EC 3-1-2 in the state of uniaxial stress. Furthermore, a thermoelastic-viscoplastic model is presented which is able to describe creep and relaxation during heating and cooling processes. The structure of this material model is chosen in such a way that the parameters can be easily identified using certain measurement results. The deviatoric part of the model consists of a rate-independent, plastic part and a rate-dependent, vis- coelastic part. The rate-independent, plastic part was formulated as a differential equation based on the endochronic theory of plasticity. The parameters of this material model are identified on the basis of the measurement results of stationary hot tensile tests on structural steel specimens. Both the non-linear-elastic EC 3-1-2 material model and the thermoelastic-viscoplastic material model with the material parameters adapted to mild steel are prepared numerically for use with finite- element-programs and implemented as UMAT-subroutines for ABAQUS in the FORTRAN code. Particular emphasis is placed on the provision of consistent tangent operators to enable efficient numerical calculation when using the material models. Finally, first finite-element-simulations are presented in order to show the possibilities of the developed and implemented material models for simulations of steel constructions in case of fire. T3 - BAM Dissertationsreihe - 167 KW - Brandschutz KW - Stahl KW - Brandverhalten KW - Finite-Elemente-Methode KW - Materialmodell KW - Eurocode 3-1-2 KW - UMAT KW - Fire prevention KW - Steel KW - Fire behaviour KW - Finite element method KW - Material model KW - Eurocode 3-1-2 KW - UMAT PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-507662 SN - 1613-4249 VL - 167 SP - i EP - 206 PB - Bundesanstalt für Materailforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-50766 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schartel, Bernhard A1 - Günther, Martin T1 - Flame retardancy of polyurethanes N2 - Polyurethanes (PU) represent one of the most versatile classes of plastics. They are processed and used as thermoplastic, elastomer, and thermoset. The requirements regarding flammability are correspondingly versatile. Depending on the material and the field of application, specific fire tests have to be fulfilled. This paper describes the different concepts used to fulfil these requirements by choosing the right raw materials and flame retardants. KW - Polyurethane KW - Flame retardant KW - Foam KW - Flammability KW - Pyrolysis KW - Cone calorimeter PY - 2020 VL - 17 IS - 1 SP - 44 EP - 48 PB - Dr. Gupta AN - OPUS4-50737 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Rabe, Sebastian A1 - Sanchez-Olivares, G. A1 - Pérez-Chávez, R. A1 - Schartel, Bernhard ED - Laoutid, F. T1 - Natural Keratin and Coconut Fibres from Industrial Wastes in Flame Retarded Thermoplastic Starch Biocomposites N2 - Natural keratin fibres derived from Mexican tannery waste and coconut fibres from coconut processing waste were used as fillers in commercially available, biodegradable thermoplastic starch-polyester blend to obtain sustainable biocomposites. The morphology, rheological and mechanical properties as well as pyrolysis, flammability and forced flaming combustion behaviour of those biocomposites were investigated. In order to open up new application areas for these Kinds of biocomposites, ammonium polyphosphate (APP) was added as a flame retardant. Extensive flammability and cone calorimeter studies revealed a good flame retardance effect with natural fibres alone and improved effectiveness with the addition of APP. In fact, it was shown that replacing 20 of 30 wt. % of APP with keratin fibres achieved the same effectiveness. In the case of coconut fibres, a synergistic effect led to an even lower heat release rate and total heat evolved due to reinforced char residue. This was confirmed via scanning electron microscopy of the char structure. All in all, these results constitute a good approach towards sustainable and biodegradable fibre reinforced biocomposites with improved flame retardant properties. KW - Biomaterials KW - Biodegradation KW - Calorimetry KW - Composites KW - Flame retardance PY - 2020 SN - 978-3-03928-350-7 SN - 978-3-03928-351-4 SP - 45 EP - 66 PB - MDPI AN - OPUS4-50738 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rabe, Sebastian A1 - Klack, Patrick A1 - Bahr, Horst A1 - Schartel, Bernhard T1 - Assessing the fire behavior of woods modified by N-methylol crosslinking, thermal treatment, and acetylation N2 - Wood products are often treated by different techniques to improve their longevity when used as building materials. Most of the time, the goal is to increase their resistance to weathering effects, deformations in material dimensions or biotic decomposition. These wood treatment techniques have a significant impact on pyrolysis and burning behavior. The general effects of three different common wood treatments on flame retardancy were investigated by comparing treated woods with their untreated counterparts and with other kinds of wood. While the acetylation of beech leads to a slightly increased fire hazard, the thermal treatment of wood and crosslinking of cellulose microfibrils dimethyloldihydroxy-ethyleneurea show a limited flame retarding effect. Switching to woods with a higher lignin content, and thus higher char yield, however, results in a more pronounced improvement in flame retardancy performance. This article delivers a comprehensive and balanced assessment of the general impact of different wood modifications on the fire behavior. Further, it is a valuable benchmark for assessing the flame retardancy effect of other wood modifications. KW - Acetylation KW - Cone claorimeter KW - DMDHEU KW - Heat of combustion KW - Thermal treatment KW - Wood modification PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-507397 DO - https://doi.org/10.1002/fam.2809 SN - 1099-1018 SN - 0308-0501 VL - 44 IS - 4 SP - 530 EP - 539 PB - Wiley Online Libary AN - OPUS4-50739 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ma, S. A1 - Xiao, Y. A1 - Zhou, F. A1 - Schartel, Bernhard A1 - Chan, Yin Yam A1 - Korobeinichev, O. P. A1 - Trubachev, S. A. A1 - Hu, W. A1 - Ma, C. A1 - Hu, Y. T1 - Effects of novel phosphorus-nitrogen-containing DOPO derivative salts on mechanical properties, thermal stability and flame retardancy of flexible polyurethane foam N2 - In this work, a series of 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) derivative salts containing phosphorus and nitrogen were synthesized, and their effects on mechanical properties, thermal stability and flame retardancy of flexible polyurethane foam (FPUF) were investigated. Studies have shown that the addition of DOPO derivatives will increase the tensile strength, compression set, and compression hardness of FPUF, but it will lead to a decrease in elongation at break. Thermogravimetric analysis showed that the initial decomposition temperature of FPUF containing DOPO derivatives was reduecd, but the char reside was significantly improved. A series of combustion tests indicated that the addition of DOPO derivative salts can improve the flame retardancy of FPUF, of which 10-hydroxy-9,10-dihydro-9-oxa-10 phosphaphenanthrene-10-oxide dicyandiamide salt (D-DICY) exhibited the best flame retardancy. When the load of D-DICY was 20 phr, the limiting oxygen index (LOI) of foam reached 24.5%, and the peak heat release rate and total heat release were decreased by 55.7% and 52.9%, respectively. Furthermore, based on the analysis of the gas phase combustion products and the char residue of the condensed phase, the possible flame retardant mechanism was proposed. KW - Flexible polyurethane foam KW - DOPO derivative salts KW - Mechanical properties KW - Thermal stability KW - Flame retardancy PY - 2020 DO - https://doi.org/10.1016/j.polymdegradstab.2020.109160 SN - 0141-3910 VL - 177 SP - 109160 PB - Elsevier Ltd. AN - OPUS4-50740 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Das Prognosetool der BAM zur Emission, Transmission und Immission von Bahnerschütterungen N2 - Die gesamte Prognose wurde rechnerisch erfasst. Die Rechenverfahren sind einfach und schnell. Die Emission und die Immission verwendet Übertragungsmatrizen. Die Transmissionsrechnung beruht auf der Dispersion der Rayleighwelle. Die Verknüpfung erfolgt über die Anregungskraft auf den Boden und über die Freifeldamplitude am Gebäude. Es sind viele Eingabemöglichkeiten für Messdaten vorgesehen. Messungen können von einem Ort auf einen anderen Ort übertragen werden. T2 - 98. Sitzung des Normausschusses "Schwingungsminderung in der Umgebung von Verkehrswegen" CY - Online meeting DA - 07.05.2020 KW - Bahnerschütterungen KW - Prognose KW - Übertragungsmatrizen KW - Rayleighwellendispersion PY - 2020 AN - OPUS4-50748 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schartel, Bernhard A1 - Günther, Martin T1 - Flammschutz von Polyurethanen N2 - Polyurethane (PU) bilden eine der vielseitigsten Klassen der Polymerwerkstoffe. Kein anderer Kunststoff wird sowohl als Thermoplast, als Elastomer wie auch als Duroplast verarbeitet und eingesetzt. Entsprechend vielfältig sind auch die Anforderungen an den Flammschutz. Je nach Material und Anwendung müssen spezifische Brandnormen erfüllt werden. Der vorliegende Aufsatz gibt einen Überblick über die verfügbaren Ansätze, um durch geeignete Auswahl der Rohstoffe und der Flammschutzmittel diese verschiedensten Anforderungen an das Brandverhalten zu erfüllen. KW - Polyurethan KW - Flammschutz KW - Pyrolyse KW - Schaum KW - Cone calorimeter PY - 2020 VL - 20 IS - 1 SP - 48 EP - 53 PB - Dr. Gupta AN - OPUS4-50736 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schlick-Hasper, Eva A1 - Neitsch, Marcel A1 - Goedecke, Thomas T1 - Industrial leak testing of dangerous goods packagings N2 - The Dangerous Goods Regulations currently do not include limit leakage rates orsensitivity requirements for industrial leak testing procedures that are equivalent tothe bubble test, which is the prescribed test method for design type testing ofdangerous goods packagings. During series production of such packagings, variousmethods are used, which often do not meet the requirements of the bubble test withregard to important criteria.Sensitivity, flow direction, pressure level and automatability are particularly importantfactors when selecting a suitable industrial leak testing method.The following methods are in principle both suitable and equally effective as thebubble test: pressure rise test (vacuum chamber), ultrasonic bubble leak detectionand gas detection methods (pressure technique by accumulation and vacuumchamber technique).To ensure a uniform test level during design type testing and production line leaktesting and therefore a comparable safety level as required by the Dangerous GoodsRegulations, it is necessary to include a more precise specification in these regula-tions. This requires, on the one hand, information about the sensitivity of the bubbletest and, on the other hand, the inclusion of a list of suitable, equally effective indus-trial test methods with their specific boundary conditions. T2 - 22nd IAPRI World Packaging CY - Online meeting KW - Bubble test KW - Dangerous goods packagings KW - Industrial leak testing KW - Leakproofness test KW - Series production PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-507521 DO - https://doi.org/10.1002/pts.2502 SP - 1 EP - 14 PB - Wiley AN - OPUS4-50752 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kowarik, Stefan A1 - Hicke, Konstantin A1 - Chruscicki, Sebastian A1 - Schukar, Marcus A1 - Breithaupt, Mathias A1 - Lämmerhirt, A. A1 - Pohl, P. A1 - Schubert, M. ED - Cranch, G. ED - Wang, A. ED - Digonnet, M. ED - Dragic, P. T1 - Train monitoring using distributed fiber optic acoustic sensing N2 - We use distributed acoustic sensing to determine the velocity of trains from train vibration patterns using artificial neural network and conventional algorithms. The velocity uncertainty depends on track conditions, train type and velocity. T2 - 27th International Conference on Optical Fiber Sensors (OFS) CY - Meeting was canceled DA - 08.06.2020 KW - Train monitoring KW - Distributed acoustic sensing KW - DAS KW - Distributed fiber optic sensing PY - 2020 SN - 978-1-55752-307-5 DO - https://doi.org/10.1364/OFS.2020.T3.25 SP - 1 EP - 4 PB - The Optical Society (Optical Society of America) CY - Washington D.C., USA AN - OPUS4-50758 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hu, W.-H. A1 - Xu, Z.-M. A1 - Liu, M.-Y. A1 - Tang, D.-H. A1 - Lu, W. A1 - Li, Z.-H. A1 - Teng, J. A1 - Han, X.-H. A1 - Said, Samir A1 - Rohrmann, R. G. T1 - Estimation of the Lateral Dynamic Displacement of High-Rise Buildings underWind Load Based on Fusion of a Remote Sensing Vibrometer and an Inclinometer N2 - This paper proposes a novel method to estimate the lateral displacement of high-rise structures under wind loads. The coefficient β(x) is firstly derived, reflecting the relation between the structural lateral dynamic displacement and the inclination angle at the height x of a structure. If the angle is small, it is the ratio between the structural fundamental mode shape and its first-order derivative without influence of external loads. Several dynamic experiments of structures are performed based on a laser remote sensing vibrometer and an inclinometer, which shows that the fundamental mode is dominated in the structural displacement response under different types of excitations. Once the coefficient β(x) is curve-fitted by measuring both the structural lateral dynamic displacement and the inclination angle synchronously, the real-time structural lateral displacement under operational conditions is estimated by multiplying the coefficient β(x) with the inclination angle. The advantage of the proposed method is that the coefficient β(x) can be identified by lateral dynamic displacement measured in high resolution by the remote sensing vibrometer, which is useful to reconstruct the displacement accurately by the inclination angle under operational conditions KW - Inclination angle KW - High-rise building KW - Lateral dynamic displacement KW - Remote sensing vibrometer PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-506833 DO - https://doi.org/10.3390/rs12071120 VL - 12 IS - 7 SP - 1120 PB - MDPI CY - 4052 Basel, Schweiz AN - OPUS4-50683 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Aris, Stephan T1 - Aktueller Stand der Normung von Gasflaschenventilen N2 - Im Vortrag wird der aktuelle Stand der Normung von Gasflaschenventilen vorgestellt. Dieser umfasst nationale, europäische und internationale Normen, die größtenteils im Bereich der Gefahrgutbeförderung verbindlich anzuwenden sind. T2 - 27. Jahrestreffen BAM/DIN/DVFG/IGV CY - Berlin, Germany DA - 27.02.2020 KW - ADR KW - Gasflaschenventile KW - Normung PY - 2020 AN - OPUS4-50701 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schlick-Hasper, Eva A1 - Goedecke, Thomas A1 - Ackermann, M. A1 - Senkel, U. T1 - Staubdichtheit von Gefahrgutsäcken und -FIBC - Überblick über Probleme in der derzeitigen Transportpraxis N2 - Gemäß den internationalen Gefahrgutvorschriften müssen Säcke und flexible Großpackmittel (Flexible Intermediate Bulk Container - FIBC) für feste Gefahrgüter staubdicht sein. In der Praxis der stichpunktartigen Kontrollen von Gefahrguttransporten durch die Autobahnpolizei Münster werden jedoch immer wieder Austritte von pulverförmigen oder körnigen Gefahrgütern aus eigentlich intakten Säcken und FIBC detektiert. Es wird ein Überblick über die im Jahr 2019 festgestellten Gefahrgutaustritte aus diesen Arten von Gefahrgutverpackungen gegeben. Darauf aufbauend wird eine systematische Einordnung hinsichtlich betroffener Bauarten und eine Diskussion möglicher Lösungsansätze vorgenommen. KW - Gefahrgutverpackungen KW - Staubdichtheit KW - Gefahrgutsäcke KW - FIBC KW - Gefahrgutkontrollen PY - 2020 SN - 2191-007 VL - 10 IS - 3 SP - 10 EP - 15 PB - VDI Fachmedien GmbH & Co. KG CY - Düsseldorf AN - OPUS4-50717 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kurth, Lutz T1 - Flame projectors for shof effects-Investigations of thermal radiation for assessing safety distances N2 - The use of flames as part of shows is state of the art. Besides pyrotechnic flame projectors, the use of projectors that produce flames by burning various gases, liquids and dusts is significantly increasing. In this study infrared radiation in the wavelength range from 7.5 to 14 microns was measured for several systems (flame projectors) and set in relation to known human pain threshold levels. From this relation safety distances been determined for a static scenario (audience watching show) and compared with those of approved pyrotechnic articles. KW - Safety distance KW - Thermal radiation KW - Flame projector PY - 2015 SN - 1082-3999 VL - 2015 IS - 34 SP - 31 EP - 36 PB - Journal of Pyrotechnics Inc. CY - Whitewater, CO 81527 USA AN - OPUS4-50054 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Schreier, Andy T1 - Distributed Brillouin sensor in polymer optical fibers utilizing BOFDA N2 - In this thesis, a distributed Brillouin sensor in perfluorinated polymer optical fibers utilizing BOFDA is presented. These commercially available polymer fibers offer beneficial characteristics for sensing applications such as higher break down strain up to 100 %, minimal bending radii below 2 mm, higher sensitivity to temperature and lower sensitivity to strain compared to their silica equivalent. The chosen wavelength of operation at 1319 nm corresponds to lower fiber propagation loss (< 37 dB/km) compared to other approaches at 1550 nm (150 - 250 dB/km). A 86 m PFGI-POF was successfully measured by BOFDA with spatial resolution of 3.4 m. The findings related to humidity influences can serve as a basis for future distributed humidity sensors not only limited to stimulated Brillouin backscattering. KW - BOFDA KW - Polymer optical fiber KW - POF KW - Brillouin sensor KW - Distributed sensor PY - 2020 SN - 978-3-7369-7146-2 SP - 1 EP - 116 PB - Cuvillier Verlag Göttingen CY - Göttingen AN - OPUS4-51041 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Longobucco, M. A1 - Stajanca, Pavol A1 - Curilla, L. A1 - Buczynski, R. A1 - Bugar, I. T1 - Applicable ultrafast all-optical switching by soliton self-trapping in high index contrast dual-core fibre N2 - The improvement potential of ultrafast all-optical switching by soliton self-trapping, using all-solid dual-core fibres with high index contrast, was analyzed numerically. The study of the femtosecond nonlinear propagation was performed based on coupled generalised nonlinear Schrödinger equations considering three fibre architectures: homogeneous cladding all-solid, photonic crystal air-glass, and photonic crystal all-solid. The structural geometries of all three architectures were optimised in order to support high-contrast switching performance in the C-band, considering pulse widths at the 100 fs level. Comparing the three structural alternatives, the lowest switching energies at common excitation parameters (1700 nm and 70 fs pulses) were predicted for the homogeneous cladding dual-core structure. Further optimization of the excitation wavelength and pulse width resulted in lower switching energies and simultaneous improvement of the switching contrasts at the combination of 1500 nm, 75 fs pulses and a fibre length of 43 mm. The spectral aspect in this optimised case expresses a broadband and uniform switching character with a span of over 200 nm and a contrast exceeding 30 dB at more frequency channels. KW - Ultrafast nonlinear propagation KW - All-optical switching KW - Dispersion tailoring of optical fibres KW - Generalised nonlinear Schrödinger equation KW - Dual-core optical fibres KW - Nonlinear directional coupler KW - Soft-glass optical fibres PY - 2020 DO - https://doi.org/10.1088/1612-202X/ab63d8 VL - 17 IS - 2 SP - 025102 PB - Astro Ltd. AN - OPUS4-51042 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Casperson, Ralf T1 - Schienenprüfung mit Wirbelstrom N2 - Ausgehend von einer Machbarkeitsstudie im Jahr 1999 wurde von der BAM in Zusammenarbeit mit der DB AG und verschiedenen anderen Partnern ein Schienenprüfsystem zur Detektion und Bewertung von Schienenfehlern des Typs Head Checks entwickelt. Dieses Prüfsystem arbeitet nach dem Wirbelstromprinzip. Die Firma Prüftechnik Linke & Rühe GmbH aus Magdeburg fertigt und vertreibt seit geraumer Zeit verschiedene manuelle und zuggestützte Prüfsysteme, die auf dieser Entwicklung basieren. Seit Januar 2013 wird in Deutschland der Qualitätsnachweis nach der Schienenbearbeitung mittels Wirbelstromprüfung gefordert. Im Laufe der Entwicklungsarbeiten wurden verschiedentlich benachbarte Themenfelder rund um die Prüfung auf Head Checks gestreift. Der Schwerpunkt dieses Vortrages liegt auf diesen erweiterten Möglichkeiten der magnetinduktiven Prüfung von verlegten Schienen. Hierbei wird sowohl auf die Verbesserung der Möglichkeiten des bestehenden Systems (z. B. durch Kopplung mit anderen Prüfverfahren) als auch auf mögliche Neuentwicklungen (z. B. durch Einsatz neuer Sensorik) eingegangen. Angestrebte Ziele sind z. B. die Verbesserung der Prüfaussage bei der Head Check Prüfung, Erweiterung der Prüfaussage auf andere Schienenfehlertypen oder die Bestimmung von Schieneneigenschaften wie Härte und Rauigkeit. T2 - ZfP im Eisenbahnwesen CY - Wittenberge DA - 15.03.2016 KW - Schienenprüfung KW - Wirbelstromprüfung KW - Zerstörungsfreie Prüfung PY - 2016 AN - OPUS4-35516 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mehdianpour, Milad A1 - Waßmuth, Carl-Friedrich T1 - Minimalinvasive Materialuntersuchungen an seilabgespannten Rohrmasten zur Bauwerkserhaltung T1 - Minimally invasive material tests on guyed tubular masts N2 - Abgespannte Stahlrohrmaste zur Rundfunkübertragung wurden in den 1950er- und 60er-Jahren häufig mit Paralleldrahtbündeln errichtet. Diese Seile werden seit geraumer Zeit wegen Korrosionsschäden sukzessive gegen vollverschlossene Spiralseile ausgetauscht. Infolge der damit einhergehenden Veränderung der Steifigkeiten ist mit dem Austausch oft eine Neuberechnung erforderlich. Unter Berücksichtigung der aktuellen Normen können nicht immer alle Nachweise erfüllt werden, selbst wenn das Bauwerk weitgehend noch intakt erscheint. Rohrschaftsanierungen sind extrem aufwändig und können den wirtschaftlichen Totalschaden darstellen, d. h., dem Bauwerk droht Abriss und Neubau. Für die Sanierung des 231 m hohen abgespannten Stahlrohrmastes am Standort Berlin Scholzplatz wurden minimalinvasive Materialuntersuchungen vorgenommen, basierend auf In-situ- und Labortests. In den statistischen Auswertungen konnte belegt werden, dass gegenüber den Angaben der Bauwerksdokumentation höhere Festigkeiten vorlagen. Durch präzise Lastannahmen und für das Bauwerk optimierte Seilvorspannungen konnten aufwändige Verstärkungsmaßnahmen des Rohrschaftes vermieden werden. KW - Bauwerkserhaltung KW - Mast, abgespannter KW - Rohrmast KW - Antennenträger aus Stahl KW - Seile KW - Materialuntersuchung KW - Härtemessung KW - Zugversuch KW - Brinellhärte/Zugfestigkeit KW - Zugfestigkeit/Streckgrenze PY - 2016 UR - http://dx.doi.org/10.1002/bate.201500094 DO - https://doi.org/10.1002/bate.201500094 SN - 1437-0999 VL - 93 IS - 1 SP - 8 EP - 13 PB - Ernst & Sohn Verlag für Architektur und technische Wissenschaften GmbH & Co. KG CY - Berlin AN - OPUS4-35522 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stroh, Julia T1 - In situ Untersuchungen von Hydratations- und Schädigungsmechanismen an Baustoffen N2 - In diesem Vortrag werden hochauflösende analytische Methoden für die Untersuchungen von zementgebundenen Baustoffen vorgestellt. Zum einen werden frühe Hydratationsprozesse in situ und mit hoher Zeitauflösung untersucht und die Einflüsse von polymeren Fließmittel und Stabilisierer auf die Erstarrungsverzögerung beobachtet. Zum anderen werden Phasenübergänge unter schädigenden Angriffen im Gefügeprofil auf µm-Skala verfolgt. Die Möglichkeit die Auswirkungen der niedrigen realen Konzentrationen von schädigenden Agenten zu identifizieren stellt ein großes Potential für die Schädigungsanalyse unter realen Bedingungen dar. Insgesamt haben die vorgestelletn analytischen Techniken ein großes Potential für die Analyse der Phasenentwicklung in zementgebundenen Baustoffen. T2 - Gemeinsamer Workshop der Sektion Angewandte Mineralogie in Umwelt & Technik und der Sektion Chemie, Physik und Kristallographie der Minerale von der Deutschen Mineralogischen Gesellschaft CY - Bad Windsheim, Germany DA - 24.02.2016 KW - Portlandzement KW - Hydratation KW - Additive KW - Schädigung KW - komplexe Angriffe PY - 2016 AN - OPUS4-35469 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN T1 - Untersuchung der Statistik "Unfälle mit wassergefährdenden Stoffen" des Statistischen Bundesamtes aus dem Jahr 2009 im Vergleich zu den Vorjahren N2 - Die BAM untersucht regelmäßig Statistiken über Unfälle mit wassergefährdenden Stoffen sowie Datenerhebungen zu Gefahrgutunfällen. Ziel ist es, Hinweise zu Tendenzen und Lücken abzuleiten, die möglicherweise Anlass für weitere Aktivitäten und Maßnahmen geben, z. B. im rechtlichen Bereich oder in der Praxis. Regelmäßig beobachtete Unfallstatistiken über Jahre geben einen guten Überblick über das Unfallgeschehen in Deutschland. Dieser Bericht betrachtet das Jahr 2009 im Vergleich zu den Vorjahren. KW - Gefahrgutunfälle KW - Unfallstatistik KW - Wassergefährdende Stoffe PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-354978 SP - 1 EP - 87 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-35497 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF ED - Rockland, Ulrike T1 - 10. Kolloquium zu Fragen der chemischen und physikalischen Sicherheitstechnik N2 - Seit 1981 veranstalten die Bundesanstalt für Materialforschung und -prüfung (BAM) und die Physikalisch-Technische Bundesanstalt (PTB) gemeinsam die Kolloquien dieser Reihe, um die Teilnehmer über aktuelle Ergebnisse und Entwicklungen auf dem Gebiet der chemischen und physikalischen Sicherheitstechnik zu informieren. Die Themen dieses Berichtsbandes informieren über Explosionsschutz zur Vermeidung explosionsfähiger Lösemittel-Dampf-Luft-Gemischen in Trocknern, Zündquellensicherheit zu Gas/Luft-, Staub/Luft- und Staubschichten, Zünddurchschlagssprozesse in Wasserstoff/Luft-Gemischen, stellen Prüfmethoden und Einflussgrößen auf die gefährlichen Eigenschaften von Ammuniumnitrat und ammoniumnitrathaltigen Zubereitungen vor, berichten über Einflüsse auf Brandverhalten und -gefahren bei Schüttgutlagerung und speziellen Werkstoffen, geben Auskunft über die Schwierigkeiten bei Anwendung neuer technischer Regeln und Richtlinien auf nationaler und europäischer Ebene und liefern neue Ansätze zur probabilistischen Riskionbetrachtung für die sichere Auslegung von Treibgasspeichern. Bei dieser Jubiläumsveranstaltung haben die Teilnehmer darüber hinaus die Gelegenheit, die neuen Versuchseinrichtungen der BAM auf dem Freiversuchsgelände in Horstwalde zu besichtigen. Dieses etwa 50 km südlich von Berlin gelegene, 12 km² große Freiversuchsgelände verfügt über einen Sprengplatz von 400 m Durchmesser für Brand- und Explosionsversuche mit Sprengwirkungen bis 150 kg TNT. Mit diesem im europäischen Raum einmaligen Gelände hat die BAM Möglichkeiten, Untersuchungen an und mit Explosivstoffen und Gegenständen mit Explosivstoff sowie Gefahrstoffen und Gefahrgütern, insbesondere im großem Maßstab und mit moderner Laborausstattung durchzuführen. Zu den Versuchsanlagen gehören unter anderem Brandwallanlagen, Modellgebäude, Schwadenkammer, Sprengkammer bzw. Sprenggrube, 12-m-Fallturm, Bunkerräume, Laboratorien und ein spezieller Lagerkomplex. Neben den Prüfungen für die Zulassung von Stoffen und Gegenständen werden diese Anlagen auch für Untersuchungen bei Schadensaufklärungen sowie in Forschungsprojekten genutzt. Allen vortragenden und an der Organisation beteiligten Kolleginnen und Kollegen sei herzlich gedankt. Ihre Beiträge und Unterstützung haben wesentlich zum Gelingen dieses 10. Kolloquiums beigetragen. T2 - 10. Kolloquium zu Fragen der chemischen und physikalischen Sicherheitstechnik CY - Berlin, Germany DA - 17.06.2004 KW - Gefahrstoffe KW - Brandgefahren KW - Freiversuchsgelände Horstwalde PY - 2004 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-356009 SP - 1 EP - 68 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-35600 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lehmann, Jens A1 - Burkert, Andreas A1 - Mietz, Jürgen T1 - Investigations proofing the passive layer stability of stainless steels N2 - The presented investigations have proved the principal suitability of the KorroPad method to assess the passive layer stability of stainless steels. The electrochemical mode of action could be described in detail and limitations of the applicability have been demonstrated. The influence of different surface finishes has been investigated and verified by known methods for describing corrosion resistances. As a result, the increased corrosion susceptibility of two ground surfaces has been detected, but also the corrosion resistance of further surface finishes could be confirmed. KW - Stainless steel KW - KorroPad KW - Passive layer PY - 2016 DO - https://doi.org/10.1002/maco.201408202 VL - 1 IS - 67 SP - 84 EP - 91 PB - WILEY-VCH Verlag GmbH & Co. KGaA CY - Weinheim AN - OPUS4-35545 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN T1 - Untersuchung der Statistik "Unfälle mit wassergefährdenden Stoffen" des Statistischen Bundesamtes aus dem Jahr 2008 im Vergleich zu den Vorjahren N2 - Die BAM untersucht regelmäßig Statistiken über Unfälle mit wassergefährdenden Stoffen sowie Datenerhebungen zu Gefahrgutunfällen. Ziel ist es, Hinweise zu Tendenzen und Lücken abzuleiten, die möglicherweise Anlass für weitere Aktivitäten und Maßnahmen geben, z. B. im rechtlichen Bereich oder in der Praxis. Regelmäßig beobachtete Unfallstatistiken über Jahre geben einen guten Überblick über das Unfallgeschehen in Deutschland. Dieser Bericht betrachtet das Jahr 2008 im Vergleich zu den Vorjahren. KW - Gefahrgutunfälle KW - Unfallstatistik KW - Wassergefährdende Stoffe PY - 2012 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-354988 SP - 1 EP - 93 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-35498 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN T1 - Untersuchung der Statistik "Unfälle mit wassergefährdenden Stoffen" des Statistischen Bundesamtes aus dem Jahr 2007 im Vergleich zu den Vorjahren N2 - Die BAM untersucht regelmäßig Statistiken über Unfälle mit wassergefährdenden Stoffen sowie Datenerhebungen zu Gefahrgutunfällen. Ziel ist es, Hinweise zu Tendenzen und Lücken abzuleiten, die möglicherweise Anlass für weitere Aktivitäten und Maßnahmen geben, z. B. im rechtlichen Bereich oder in der Praxis. Regelmäßig beobachtete Unfallstatistiken über Jahre geben einen guten Überblick über das Unfallgeschehen in Deutschland. Dieser Bericht betrachtet das Jahr 2007 im Vergleich zu den Vorjahren. KW - Gefahrgutunfälle KW - Unfallstatistik KW - Wassergefährdende Stoffe PY - 2010 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-355008 SP - 1 EP - 86 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-35500 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN T1 - Untersuchung der Statistik "Unfälle mit wassergefährdenden Stoffen" des Statistischen Bundesamtes aus dem Jahr 2006 im Vergleich zu den Vorjahren N2 - Die BAM untersucht regelmäßig Statistiken über Unfälle mit wassergefährdenden Stoffen sowie Datenerhebungen zu Gefahrgutunfällen. Ziel ist es, Hinweise zu Tendenzen und Lücken abzuleiten, die möglicherweise Anlass für weitere Aktivitäten und Maßnahmen geben, z. B. im rechtlichen Bereich oder in der Praxis. Regelmäßig beobachtete Unfallstatistiken über Jahre geben einen guten Überblick über das Unfallgeschehen in Deutschland. Dieser Bericht betrachtet das Jahr 2006 im Vergleich zu den Vorjahren. KW - Gefahrgutunfälle KW - Unfallstatistik KW - Wassergefährdende Stoffe PY - 2009 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-355015 SP - 1 EP - 84 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-35501 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -