TY - JOUR A1 - Nerger, Deborah A1 - Moosavi, Robabeh A1 - Bracklow, F. A1 - Hering, M. A1 - Kühn, T. A1 - Curbach, M. A1 - Hille, Falk A1 - Rogge, Andreas T1 - Planar tomography and numerical analysis for damage characterization of impact loaded RC plates N2 - The damage analysis of reinforced concrete (RC) is of high interest for reasons of effective maintenance and structural safe-ty of buildings. The damage structures of RC plates loaded by an impact were investigated, applying X-ray planar tomogra-phy and finite element method (FEM). Planar tomography allows getting three-dimensional information of the RC elements and the damage including crack, spalling and scabbing. The FEM model validated on the tomography data justifies the appli-cation for further predictions of the damage description. In this study, we investigated concrete plates of three different thick-ness subjected to impacts at different low- and medium-velocity, whereby the used impactor had a flat tip, which resulted in small penetrations on the front side and scabbing on the rear side. In order to quantify the damage, the damage volume and its distribution through the plate were computed and the correlations between degree of damage and impact velocity were found out. KW - Impact KW - Damage characterization KW - Planar tomography KW - Numeric simulation KW - Reinforced concrete structure PY - 2020 DO - https://doi.org/10.1002/cend.202000017 VL - 8 SP - 1 EP - 19 PB - Wiley AN - OPUS4-51117 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nerger, Deborah A1 - Hille, Falk A1 - Moosavi, Robabeh A1 - Grunwald, Marcel A1 - Redmer, Bernhard A1 - Kühn, T. A1 - Hering, M. A1 - Bracklow, F. T1 - Post-impact evaluation at RC plates with planar tomography and FEM N2 - Due to the wide range of applications, the easy production and the large field of use, reinforced concrete (RC) is a widespread building material. This variety of applications is reflected in a wide range of physical material properties. Not only therefor it still is a technical challenge to provide all necessary test conditions for experimentally reproducing dynamic effects under impact loading of RC structures. In this paper we present investigations on the thicknesses of RC plates under low and medium high velocity impact loading by a flat-tipped impactor. The planar tomography setup at BAM is used to visualize the impact damage and to characterize the damage features such as cracks, scabbing and spalling. Further, the comparison of tomography results with those of an applied numeric simulation analysis is used to verify the numeric models for future damage prognosis under impact loading. Using the results of both, the tomographic as well as the FE analysis, different damage features were investigated and compared regarding their validity. Crack damage plays a leading part and the significance of summarized crack values as well as their distribution is analyzed. The total damage value but also the determined damage distribution both provide an input for describing damage as a function of the impactor velocity and plate thickness. KW - Reinforced concrete structure KW - Post-impact evaluation KW - Damage characterization KW - Ansys Autodyn KW - Drucker-Prager KW - Planar tomography PY - 2020 DO - https://doi.org/10.1016/j.matpr.2020.05.671 SP - 1 EP - 10 PB - Elsevier AN - OPUS4-51115 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ghafafian, Carineh T1 - Damage Mechanisms of Scarf Joint Repairs for Wind Turbine Rotor Blade Shell Applications N2 - Wind turbine rotor blades, made of fiber reinforced polymers (FRP), often fail before their projected 20-year lifespan, largely due to defects that originate during manufacturing and are propagated by operational fatigue and environmental conditions. The cost-intensive replacement outcomes lead to a high loss of earnings, and are one of the inhibitors of wind turbine production [1]. A potential repair alternative is to locally patch these areas of the blades with adhesively bonded structural repairs. However, the effects of such repair methods of the outer shell region on the structural integrity of the rotor blades are still largely unknown, and are thus investigated in this project. The shell components of rotor blades are made of FRP composite material sandwiching a lightweight core, often a rigid foam or Balsa wood. The repair methods involve replacing the lost load path with a new material that is joined to the parent structure [2]. Repairs in this project focus on the scarf method, which allow for a smoother load distribution across the joint, aiming to study the damage mechanism of glass FRP scarf repairs for wind turbine blade shell applications. Namely, the source and path of the damage initiation and propagation, role of the interface between parent and patch material, and the role of the fiber orientation mismatch at this interface are examined. Biaxial ±45° and 0/90° FRP specimens are produced with the vacuum-assisted resin infusion (VARI) process using E-glass non-crimp fabric. The patch layers are then joined using VARI with a scarf ratio of 1:50, using glass FRP fabric with half the areal weight of the parent side to allow for better drapability. The methods and practices in specimen production are based on common industry practice in rotor blade shell manufacturing and repairs. The specimens are tested under uniaxial tensile load, during which they are periodically monitored for damage onset. A comparison of the ±45° and 0/90° specimens allows for an understanding of the role of a highly mismatching fiber orientation in the transition zone between parent and patch material on the failure mechanism of the scarf joint. Although failure in both orientations begins as delamination at the joint edge, the difference in the mechanisms at play in the two different specimen types leads ultimately to different fracture paths. Namely, in the inter fiber failure mechanism of the ±45° specimens, the higher interlaminar strength compared to the intralaminar strength of the laminate leads to intralaminar failure of the ±45° scarf joint specimens. Alternatively, the competition in the 0/90° specimens lies between the interlaminar strength and fiber failure strength, and here we experience failure primarily across the scarf joint length. The scarf joint in the 0/90° specimens disrupts the continuity of the load-carrying 0° layers, directing the failure path to remain primarily along the scarf joint. Experimental results are compared to finite element analyses of scarf patch repairs on glass FRP sandwich specimens with the same respective layup orientations, where the damage initiation regions are identified and correlated to fiber orientation, serving as a bridge to future work which will experimentally examine the scarf repair patches on sandwich shell specimens. T2 - Joint Event: ICCS23 - 23rd International Conference on Composite Structures & MECHCOMP6 - 6th International Conference on Mechanics of Composites CY - Online meeting DA - 01.09.2020 KW - Wind turbine blade shells KW - Glass fiber reinforced polymers KW - Scarf repairs PY - 2020 AN - OPUS4-51175 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Popiela, Bartosz T1 - FEM-Analyse der Reparaturstellen an FKV-Sandwichplatten N2 - Untersuchung des Einflusses des Reparaturpatches auf das Verhalten der reparierten GFK-Sandwichproben unter Zug-, Druck- und Schubbeanspruchung. T2 - 25. Nationales SAMPE-Symposium CY - Kassel, Germany DA - 18.02.2020 KW - Rotorblätter KW - Glasfaserverstärkter Kunststoff KW - Sandwichstruktur PY - 2020 AN - OPUS4-50544 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lozano-Martín, D. A1 - Martín, M. C. A1 - Chamorro, C. R. A1 - Tuma, Dirk A1 - Segovia, J. J. T1 - Speed of sound for three binary (CH4 + H2) mixtures from p = (0.5 up to 20) MPa at T = (273.16 to 375) K N2 - Speed of sound is one of the thermodynamic properties that can be measured with least uncertainty and is of great interest in developing equations of state. Moreover, accurate models are needed by the H2 industry to design the transport and storage stages of hydrogen blends in the natural gas network. This research aims to provide accurate data for (CH4 + H2) mixtures of nominal (5, 10, and 50) mol-% of hydrogen, in the p = (0.5 up to 20) MPa pressure range and with temperatures T = (273.16, 300, 325, 350, and 375) K. Using an acoustic spherical resonator, speed of sound was determined with an overall relative expanded (k = 2) uncertainty of 220 parts in 10^6 (0.022%). Data were compared to reference equations of state for natural gas-like mixtures, such as AGA8-DC92 and GERG-2008. Average absolute deviations below 0.095% and percentage deviations between 0.029% and up to 0.30%, respectively, were obtained. Additionally, results were fitted to the acoustic virial equation of state and adiabatic coefficients, molar isochoric heat capacities and molar isobaric heat capacities as perfect-gas, together with second and third acoustic virial coefficients were estimated. Density second virial coefficients were also obtained. KW - Speed of sound KW - Acoustic resonator KW - Heat capacity PY - 2020 DO - https://doi.org/10.1016/j.ijhydene.2019.12.012 SN - 0360-3199 VL - 45 IS - 7 SP - 4765 EP - 4783 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-50454 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lozano-Martín, D. A1 - Akubue, G. U. A1 - Moreau, A. A1 - Tuma, Dirk A1 - Chamorro, C. R. T1 - Accurate experimental (p, rho, T) data of the (CO2 + O2) binary system for the development of models for CCS processes N2 - The limited availability of accurate experimental data in wide ranges of pressure, temperature, and composition is the main constraining factor for the proper development and assessment of thermodynamic models and equations of state. In the particular case of carbon capture and storage (CCS) processes, there is a clear need for data sets related to the (carbon dioxide + oxygen) mixtures that this work aims to address. This work provides new experimental (p, rho, T) data for three binary (CO2 + O2) mixtures with mole fractions of oxygen x(O2) = (0.05, 0.10, and 0.20) mol/mol, in the temperature range T = (250 to 375) K and pressure range p = (0.5 to 13) MPa. The measurements were performed with a high-precision single-sinker densimeter with magnetic suspension coupling. The density data were obtained with estimated expanded relative uncertainties of 0.02 % for the highest densities and up to 0.3 % for the lowest ones.The results were compared to the corresponding results calculated by the current reference equations of state for this kind of mixtures, namely the EOS-CG (combustion gases) and the GERG-2008 equation of state, respectively. The EOS-CG yields better estimations in density than the GERG-2008 equation of state. The results from the EOS-GC model show no systematic temperature dependence. For the GERG-2008 model, however, this criterion is significantly less fulfilled. KW - carbon capture and storage KW - single-sinker densimeter KW - equation of state PY - 2020 DO - https://doi.org/10.1016/j.jct.2020.106210 SN - 0021-9614 VL - 150 SP - 106210 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-50925 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schaumann, P. A1 - Schürmann, K. A1 - Pittner, Andreas A1 - Rethmeier, Michael T1 - Experimental investigations on the fatigue resistance of automatically welded tubular X-joints for jacket support structures N2 - The development within the offshore wind sector towards more powerful turbines combined with increasing water depth for new wind parks is challenging both the designer as well as the manufacturer of bottom fixed support structures. Besides XL-monopiles, the market developed an innovative and economic jacket support structure which is based on automatically manufactured tubular joints combined with standardized pipes. Besides the improvements for a serial manufacturing process the automatically welded tubular joints show a great potential in terms of fatigue resistance e.g. due to a smooth weld geometry without sharp notches. However, these benefits are not considered yet within the fatigue design process of automatically manufactured jacket substructures according to current standards due to the lack of suitable S-N curves. Therefore, 32 axial fatigue tests on single and double-sided automatically welded tubular X-joints have been performed to determine a new hot spot stress related S-N curve. Based on these constant amplitude fatigue tests a new S-N curve equal to a FAT 126 curve was computed which implicitly includes the benefits of the automatically welding procedure. T2 - EERA Deep Wind 2020 CY - Trondheim, Norway DA - 15.01.2020 KW - Notch stress approach KW - Fatigue tests KW - Automated manufacturing KW - Tubular X-joints KW - Structural stress approach PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-518509 DO - https://doi.org/10.1088/1742-6596/1669/1/012022 VL - 1669 SP - 012022 PB - IOP Publishing Ltd AN - OPUS4-51850 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Baeßler, Matthias A1 - Cuéllar, Pablo A1 - Victor, A. A1 - Lüddecke, F. ED - Triantafyllidis, T. T1 - Stability and large deformations of slender structures supported by soil materials N2 - The stability and geometric nonlinearities of slender structures are a major topic in structural design. While this topic is most relevant in the field of Structural Engineering, e.g. for steel or concrete structures, only few applications take the role of soil-structure-interaction explicitly into account. The focus of this paper is placed on the impact of soil support and its modelling for the buckling analysis based on examples both for pile foundations and for railway track stability. The general interaction between steel design and the geotechnical input will be addressed. The paper discusses and summarizes a range of subtopics based on experience and current research at the author’s institute. KW - Buckling soil-structure-interaction offshore piles track PY - 2020 SN - 978-3-030-28515-9 SN - 978-3-030-28516-6 DO - https://doi.org/10.1007/978-3-030-28516-6 SN - 1613-7736 SN - 1860-0816 VL - 91 SP - 355 EP - 369 PB - Springer CY - Cham, Switzerland AN - OPUS4-49166 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thomas, Sebastian T1 - Improvement of Type Approval Regulations of Pressure Vessels for Hydrogen Fueled Vehicles using Probabilistic Methods N2 - Composite pressure vessels (CPVs) are becoming the state of the art for storage for compressed hydrogen (CH2) in automotive applications. There is a strong interest of car manufacturers to use lightweight and less-costly gas storage units. In order to reduce the necessary amount of expensive carbon fibre, the nominal safety margins are becoming gradually smaller, pushing the limits of the regulations for type approval. At the same time, the total volume of these vessels increases to extend the range of the vehicles, increasing the consequences for worst-case scenarios like the rupture of the CPVs in service. This presentation presents insights gained in the project “TAnk HYdrogen Automotive” (TAHYA). Its aim is to improve the safety of current regulations for type approval of pressure vessels for the use in hydrogen fueled vehicles, namely GTR No. 13 and ECE R 134. For the assessment of safety, the probabilistic approach developed by division 3.5 of BAM is used. Monte-Carlo-Simulations were conducted leading to the identification of several weak spots, mainly found in the burst test and the batch test. By changing the requirements for burst tests and the approach for batch tests, the identified weak spots can be strongly reduced. T2 - Colloquium of Department 3 CY - Online meeting DA - 19.11.2020 KW - Monte-Carlo Simulation KW - Safety Assessment KW - Pressure Vessel PY - 2020 AN - OPUS4-51696 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas A1 - Wille, Frank A1 - Neumann, Martin A1 - Linnemann, Konrad ED - Baraldi, P. ED - Di Maio, F. ED - Zio, E. T1 - Safety Evaluation of a Package for Radioactive Waste by Full-Scale Drop Testing N2 - As part of the evaluation of a package for the safe transport of radioactive waste the regulations of the IAEA International Atomic Energy Agency shall be fulfilled. The regulations define requirements for the package and specify mechanical and thermal test conditions. Different methods are allowed for the test performance to demonstrate compliance with the regulations. Next to calculational approaches and the use of models of an appropriate scale, the performance of full-scale testing with prototype packages respectively full-scale models is applied. The use of full-scale models has several advantages within the complete safety assessment procedure for a transport package approval. Scaling and corresponding similarity questions don’t have to be considered, additional material investigations can be limited and analyses to transfer test results to the original package design are reduced in number and complexity. Additionally, experience for future serial design procedures can be built up during manufacturing and assembling of the test model. BAM operates different drop and fire test facilities south of Berlin, Germany. BAM has started to perform a drop test campaign with a full-scale model of 120 metric tons weight for a transport package approval procedure. The paper describes experience with test preparation, drop performance and additional analyses. The measurement concept is explained and test goals regarding the package safety assessment and evaluation of safety margins are introduced. T2 - 30th European Safety and Reliability Conference and 15th Probabilistic Safety Assessment and Management Conference (ESREL2020 PSAM15) CY - Online meeting DA - 01.11.2020 KW - Slap-down KW - Transport safety KW - Package KW - Drop test KW - Similarity KW - FEA KW - Radioactive waste PY - 2020 UR - https://www.rpsonline.com.sg/proceedings/esrel2020/html/3809.xml SN - 987-981-14-8593-0 SP - Paper 3809,1 EP - 8 PB - Research Publishing Services CY - Singapore AN - OPUS4-50981 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krebber, Katerina A1 - Weege, S. A1 - Großwig, S. A1 - Obermöller, M. A1 - Perk, M. A1 - Lu, Xin A1 - Schukar, Marcus A1 - Weber, U. A1 - Pfeiffer, T. A1 - Rembe, M. T1 - Kombinierte faseroptische Messungen in Bohrlöchern helfen bei der Detektion von Kleinstleckagen N2 - Seit November 2019 läuft ein breit angelegtes und vom BMWi gefördertes ZIM-Kooperationsprojekt zwischen der Bundesanstalt für Materialforschung und -prüfung (BAM), der IAB'Weimar gGmbH, der GKSO GmbH & Co. Projekt KG, der DEEP.KBB GmbH sowie der Rembe Consulting PartG mbB. Ziel des Forschungsvorhabens sind sowohl die Lokalisierung als auch die Quantifizierung insbesondere sehr kleiner Leckagen in einer Bohrlochverrohrung durch die Nutzung faseroptischer Messtechnik. Durch Messdatenkopplung und den Wegfall bewegungsbedingter Nachteile einer Messsonde werden wesentlich präzisere Ergebnisse zur Bewertung der Bohrlochintegrität als üblich erwartet. T2 - DGMK/ÖGEW-Frühjahrstagung 2020 CY - Meeting was canceled DA - 15.04.2020 KW - Wasserstoffspeicher KW - Kavernenspeicher KW - Verteilte faseroptische akustische Sensorik PY - 2020 VL - 6 SP - 43 EP - 43 PB - DVV Media Group CY - Hamburg AN - OPUS4-52233 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mair, Georg W. A1 - Becker, B. A1 - John, Sebastian A1 - Duffner, Eric T1 - Composite storage systems for compressed hydrogen - systematic improvement of regulations for more attractive storage units N2 - Hydrogen is an attractive energy carrier that requires high effort for safe storage. Forensuring safety, they must undergo a challenging approval process. Relevant standardsand regulations for composite cylinders used for the transport of hydrogen and for its on-board storage are currently based on deterministic (e.g. ISO 11119-3) or semi-probabilistic(UN GTR No. 13) criteria. This paper analysis the properties of such methods withrespect to the evaluation of load cycle strength. Their characteristics are compared withthe probabilistic approach of the BAM. Based on Monte-Carlo simulations, the availabledesign range (mean value and scatter of strength criteria) of current concepts was exem-plarily estimated. The aspect of small sample sizes is analysed and discussed with respectto the evaluation procedures. KW - Probabilistic KW - Monte-Carlo KW - Regulations KW - Composite cylinder KW - Hydrogen vehicles KW - Transport of dangerous goods PY - 2020 DO - https://doi.org/10.1016/j.ijhydene.2018.04.068 SN - 0360-3199 VL - 45 IS - 25 SP - 13672 EP - 13679 PB - Elsevier Ltd. AN - OPUS4-50687 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Markthochlauf von Wasserstoff - Vertrauen durch probabilistische Sicherheitsbewertung der H2-Speicher N2 - Der Vortrag beginnt mit dem erwarteten Bedarf an Wasserstoff und der Frage der Risikosteuerung bei stattfindender Marktdurchsetzung. Dem gegenüber ist an einem Beispiel der Prozess der Regelsetzung gestellt, was die Notwendigkeit pro-aktiven Handelns zeigt. Es wird über die risikobasierte Definition von Sicherheit gezeigt, welche Bedeutung die Erfassung der Fertigungsstreuung hat und wie die quantitative Erfassung und Bewertung aussehen könnte. Zuletzt wird über den Aspekt der Alterung auf das Potential probabilistischer Zulassungsansätze verwiesen und aufgezeigt, wie die Wirkung von Vorschriften nach dem probabilistischen Sicherheitskriterium bewertet und optimiert werden kann. T2 - 9. HYPOS-Dialog: Grüner Wasserstoff, aber sicher! (Uni Magdeburg) CY - Magdeburg, Germany DA - 11.09.2020 KW - Wasserstoffspeicher KW - Monte-Carlo-Experiment KW - Lebensdauervorhersage KW - Statistische Bewertung KW - Sicherheit KW - Population PY - 2020 AN - OPUS4-53154 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gumenyuk, Andrey T1 - New developments in high power laser and hybrid welding of thick plates for application in modern ship building N2 - High power laser beam welding has been already introduced in ship building industry since last two decades and is characterized by higher performance as conventional arc welding technologies through its higher welding speed, penetration depth and therefore higher productivity. Moreover, high quality weld joints are achievable thanks to a stronger automatization degree and better repeatability of the process. A further advantage of the laser beam welding is a manufacturing of parts with very low distortion according to much lower heat input, so that rework amount can be reduced significantly. Nevertheless, there are still some unresolved problems limiting the range of application of the technology in part manufacturing within ship building industry, restricted by development and application of new materials or new design of ship vessels. The present contribution deals with some novel aspects of laser beam welding technology allowing to widen this range significantly. One of the possibilities is to increase the weld seam thickness for single pass laser or laser-hybrid welding is to apply contactless EM-support system based on generation of the Lorentz force counteracting the liquid metal drop out. Also, application of laser-hybrid welding technology for welding novel materials like cold resistant steel X8Ni9 used for construction of LNG tanks brings technological and design advantages comparing to conventional welding technologies by using of a similar alloyed filler wire instead of expensive Ni-based filler material. Finally, it is shown how the application of computational techniques can be used to helps to improve the quality of laser welded joints and avoid the critical weld failure by optimization of the welding process parameters. T2 - SHY Virtual Laserforum 2020 CY - Online meeting DA - 01.09.2020 KW - Ship building KW - Laser beam welding KW - Hybrid laser arc welding PY - 2020 UR - https://laserforum.mobieforum.fi/ AN - OPUS4-51221 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Schaumann, P. A1 - Schürmann, K. A1 - Pittner, Andreas A1 - Rethmeier, Michael T1 - Quantifizierung der Einflüsse aus Fertigungsautomatisierung und Innenschweißen auf die Ermüdungsfestigkeit von Hohlprofilknoten für Offshore-Windenergieanlagen T1 - Quantifying the effects of manufacturing automation and internal welding on the fatigue resistance of circular hollow section joints for offshore wind energy converters N2 - Die Entwicklung in der Offshore-Windenergie hin zu größeren, leistungsstärkeren An-lagentypen sowie die zeitgleich zunehmenden Wassertiefen der projektierten Wind-parks stellt u. a. Designer und Fertiger der Gründungsstrukturen von Windenergiean-lagen vor wachsende Herausforderungen. Neben dem Gründungskonzept der XL-Monopiles rückt wegen der Kombination aus dem vergleichsweise geringen Materialverbrauch bei gleichzeitig hoher Steifigkeit, auch die Jacketgründung in den Fokus. Der Fertigungsaufwand der Jackets ist verglichen mit Monopiles groß; kann jedoch durch die Nutzung von Standardrohren mit automatisiert gefertigten Jacketknoten reduziert werden. Vor diesem Hintergrund beschreibt der vorliegende Forschungsbericht den Fertigungs-prozess zum automatisierten Schweißen von X-förmigen Hohlprofilknoten für Jacket-Gründungsstrukturen von Offshore-Windenergieanlagen. Ein weiteres wesentliches Ziel dieses Vorhabens war die konsequente Digitalisierung der schweißtechnischen Fertigungskette während der automatisierten Schweißung der X-Knoten. Die so ge-speicherten Prozessparameter können zum einen als Grundlage einer Qualitätskon-trolle dienen, zum anderen ermöglichen sie eine vollständige Nachverfolgbarkeit der automatisiert gefertigten Rohrknoten. Der zweite maßgebend in diesem Bericht behandelte Aspekt umfasst die Quantifizie-rung der Einflüsse aus Fertigungsautomatisierung und Innenschweißen auf die Ermü-dungsfestigkeit der Hohlprofilknoten auf Basis serieller Ermüdungsversuche. Dazu wurden im Projekt zwei Serien mit jeweils 16 Schwingversuchen an ein- und doppel-seitig automatisiert geschweißten X-Knoten durchgeführt und entsprechende Struktur-spannungswöhlerlinien für die automatisiert gefertigten X-Knoten bestimmt. Die Ergebnisse dieser Ermüdungsversuche werden abschließend in numerischen Untersuchungen auf Basis der Strukturspannungs- und des Kerbspannungskonzeptes gegenübergestellt, um die Prognosefähigkeit beider Konzepte für die ermüdungs-kritischen Bereiche des X-Knotens bewerten zu können. Durch die im Forschungsvorhaben durchgeführten schweißtechnischen, experimen-tellen und numerischen Analysen konnte das Potential automatisiert gefertigter Rohr-knoten hinsichtlich Reproduzierbarkeit und Ermüdungsverhalten quantifiziert werden. Zusätzlich konnte der Einfluss der inneren Schweißnaht auf die Ermüdungsfestigkeit bewertet werden. N2 - The development within the offshore wind sector towards more powerful turbines combined with increasing water depth for new wind parks is challenging both the designer as well as the manufacturer of bottom fixed support structures. Besides XL-monopiles, the market developed an innovative and economic jacket support structure, which is based on automatically manufactured tubular joints combined with standardized pipes. Besides the improvements for a serial manufacturing process the automatically welded tubular joints show a great potential in terms of fatigue resistance e.g. due to a smooth weld geometry without sharp notches. However, these benefits are not considered yet within the fatigue design process of automatically manufactured jacket substructures according to standards and guidelines due to the lack of suitable S-N curves. Therefore, within this research project the automatically welding process of tubular joints for jacket support structures of offshore wind energy turbines was developed. Additionally, the project was focused on a consistent digitalization of the welding production chain during the automated welding of the X-joints. These stored process parameters can then serve as the basis for quality checks and a complete traceability of the automatically produced tubular joints is enabled. The second aspect dealt within this report is the quantification of the effects of production automation and internal welding on the fatigue resistance of the tubular joints by performing serial fatigue tests. For this purpose, two series each with 16 fatigue tests on single- and double-sided automatically welded X-joints were carried out in the project to determine structural stress based S-N curves for the automatically welded X-joints. The results of these fatigue tests are then compared to numerical investigations based on the structural stress as well as notch stress approach. The outcomes are then compared to evaluate the capability of both approaches for the prediction of the fatigue-critical locations within the X-joints. Based on the analysis of the welding procedure as well as the experimental and numerical investigations within this research project, the potential of automatically manufactured tubular joints with regard to reproducibility and fatigue behaviour was investigated. In addition, the effects of an inner root layer on the fatigue resistance was evaluated. KW - Lightweight Design KW - Jacket Support Structures KW - Fatigue KW - Arc Welding Automation KW - Offshore Wind PY - 2020 UR - https://shop.stahldaten.de/produkt/p-1178-quantifizierung-der-einfluesse-aus-fertigungsautomatisierung-und-innenschweissen-auf-die-ermuedungsfestigkeit-von-hohlprofilknoten-fuer-offshore-windenergieanlagen SN - 978-3-946885-79-5 VL - Bericht P1178 SP - 1 EP - 189 AN - OPUS4-51855 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Pittner, Andreas A1 - Rethmeier, Michael T1 - Ökologische Bilanzierung von Schmelzschweißverfahren unter Berücksichtigung vor- und nachgelagerter Prozessschritte N2 - Schweißen ist ein industriell relevantes Fertigungsverfahren mit einer branchenübergreifenden Bedeutung. Die Umweltwirkungen von Schweißverfahren sind jedoch bisher unbekannt und werden im Entstehungsprozess eines Produktes entlang seiner Fertigungskette daher meist nicht berücksichtigt. Ferner ist der Schweißprozess durch einen hohen Verbrauch an Energie sowie Ressourcen gekennzeichnet. Zahlreiche Arbeiten zeigen, dass der Bedarf einer Ökobilanzierung enorm ist. Ursächlich für die bisher mangelhafte Etablierung der Ökobilanzierung von Schweißverfahren und damit Motivation für die Forschungsarbeiten ist die Unkenntnis relevanter Einflussgrößen und damit verbunden ein nicht abschätzbarer Aufwand bei der Durchführung sowie Implementierung einer Ökobilanz im fertigungstechnischen Kontext. Demgegenüber ist die Ökobilanzierung in anderen Branchen ein oft genutztes Werkzeug zur Ableitung von Umweltwirkungen. Aufgrund der aktuellen Diskussionen bezüglich des Übergangs hin zu einer klimaneutralen Produktion erfährt auch die Analyse und Optimierung der Umweltwirkungen schweißtechnischer Fertigungsverfahren derzeit eine gesteigerte Aufmerksamkeit. Für Unternehmen stellt die Verfügbarkeit umweltverträglicher Produkte bzw. Prozesse eine gewisse Werbewirksamkeit dar, wie dies im Bereich der Schweißstromquellentechnik aktuell zu beobachten ist. Gleichzeitig wird das Thema des „green welding“ auch bezogen auf die gesamte Fertigungskette immer häufiger diskutiert. Dies zeigt sich durch eine in den letzten Jahren deutlich gestiegene Publikationsaktivität. Neben Analysen zu den Einflussfaktoren auf die Nachhaltigkeit in schweißtechnischen Produktionsumgebungen stehen vor allem auch konkrete Implementierungen in der Fertigung bzw. der Produktentstehung im Fokus. Die grundlegende Vorgehensweise einer Ökobilanzierung (Life-Cycle-Assessment bzw. Abk. LCA) ist als standardisierte Methode in geltenden Normen] sowie in entsprechender Fachliteratur beschrieben. Kernelement der Ökobilanzierung ist die Sachbilanzierung, d.h. die Erfassung der relevanten Inputs sowie Outputs bezogen auf das System „Schweißprozess“. Aus dem entlang der schweißtechnischen Fertigungskette akkumulierten Ressourcenverbrauch während des Schweißens (z.B. Zusatzwerkstoff, elektrische Energie, Schutzgas, etc.) und Abfallprodukten bzw. Emissionen wird die Umweltwirkung entsprechend verschiedener Kategorien, z.B. dem CO2-Äquivalent, gemäß der World Steel Association abgeleitet. In der schweißtechnischen Community ist es bekannt, dass die Umweltwirkung von Schweißprozessen qualitativ direkt aus dem Ressourcenverbrauch abgeleitet werden kann. Der Einfluss der verschiedenen Input- sowie Outflüsse auf ausgewählte Wirkkategorien ist jedoch nicht ad-hoc quantifizierbar. Die Forschungsarbeiten haben gezeigt, dass der Materialverbrauch (z.B. Grund-/Zusatzwerkstoff, etc.), der Energieverbrauch (z.B. Wirkleistung sämtlicher elektrischer Verbraucher während der Prozesszeit), Gasverbrauch (Prozess-, Schutzgas oder Druckluft) sowie Hilfsmittel (z.B. Schutzgläser) signifikante Inputgrößen darstellen, deren Berücksichtigung im Rahmen einer Prozessökobilanz ausreichend ist. Eine wesentliche Forderung des projektbegleitenden Ausschusses war, Methoden für eine direkte Implementierung, um somit Nachnutzung der Ergebnisse zu entwickeln. Um die Ökobilanzierung als festen Bestandteil in die schweißtechnische Dokumentation einfließen zu lassen, sind die notwendigen Arbeitsschritte zu automatisieren. Daher wurden im Rahmen der Forschungsarbeiten sämtliche zu berücksichtigenden Größen durch ein an der Forschungsstelle entwickelten Schweißdatenmanagements digital erfasst sowie archiviert und in eine Umweltwirkung durch Zugriff auf entsprechende Open-Source Datenbanken „übersetzt“. Das Datenmanagement ermöglicht die eindeutige Zuordnung der Umweltwirkung eines geschweißten Bauteiles ohne Dokumentationsaufwand für den Anwender. Dadurch werden insbesondere KMU in die Lage versetzt, den Anforderungen bezüglich der Bewertung der Ökoeffizienz von Fertigungsverfahren gerecht zu werden und somit auf die nationalen sowie internationalen klimapolitischen Rahmenbedingungen vorbereitet zu sein. Die Analysen eines breiten Spektrums an Schweißverfahren haben gezeigt, dass eine Verringerung der Umweltwirkungen von Schweißverfahren demnach nur primär durch eine Reduktion des Zusatzwerkstoff- sowie Energieverbrauches zu realisieren ist. Hierbei zeigen Verfahren mit niedrigem Werkstoffeinsatz, im Extremfall autogene Verfahren, die geringsten Umweltwirkungen. Im Produktentstehungsprozess ist es daher notwendig, unter Berücksichtigung der Schweißbarkeit die ökologischen Verfahrenscharakteristika hinsichtlich konstruktiver, fertigungstechnischer sowie werkstoffspezifischer Randbedingungen zu bewerten, um die vorgeschriebenen Produkteigenschaften zu gewährleisten und die Umweltbelastung zu minimieren. Damit der Workflow, der bei der Ökobilanzierung zu durchlaufen ist, vereinheitlicht und für jeden verständlich ist, fließen die Forschungsergebnisse direkt in die DIN SPEC 35235 „Nachhaltigkeit in der Schweißtechnik – Ökobilanzierung von Schweißverfahren“ ein. Dies ist die Grundlage, um die Vergleichbarkeit von Ökobilanzen in der Schweißtechnik zu gewährleisten und so deren Akzeptanz in der Industrie zu erhöhen. Damit ist ein optimaler Transfer der Forschungsergebnisse in die Industrie gewährleistet. KW - Schweißverfahren KW - Ökobilanzierung PY - 2020 SP - 1 EP - 38 PB - DVS Media CY - Düsselorf AN - OPUS4-51856 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - John, Sebastian T1 - Delfin - Statusbericht zum 4.HJM N2 - Präsentation über den Fortschritt der BAM zum Vorhaben Delfin, welches sich mit der Entwicklung und Schädigungsneigung von Composite-Wasserstoffbehältern für den Anwendungsfall KFZ beschäftigt T2 - 4. Halbjahresmeeting zum Vorhaben Delfin CY - Online meeting DA - 21.10.2020 KW - Wasserstoff KW - Impact KW - Druckbehälter PY - 2020 AN - OPUS4-51495 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Munzke, Dorit A1 - Duffner, Eric A1 - Eisermann, René A1 - Schukar, Marcus A1 - Schoppa, André A1 - Szczepaniak, Mariusz A1 - Strohhäcker, J. A1 - Mair, Georg W. T1 - Monitoring of type IV composite pressure vessels with multilayer fully integrated optical fiber based distributed strain sensing N2 - We present the results of distributed fiber optic strain sensing for condition monitoring of a hybrid type IV composite fully wrapped pressure vessel using multilayer integrated optical fibers. Distributed strain sensing was performed for a total number of 252,000 load cycles until burst of the vessel. During this ageing test material fatigue could be monitored and spatially localized. Critical material changes were detected 17,000 cycles before material failure. Results have been validated by acoustic emission analysis. T2 - 12th International Conference on Composite Science and Technology (ICCST12) CY - Sorrento, Italy DA - 08.05.2019 KW - Hybrid composite pressure vessel KW - Distributed fiber optic sensing KW - Acoustic emission analysis KW - Structural health monitoring PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-516772 DO - https://doi.org/10.1016/j.matpr.2020.02.872 SN - 2214-7853 VL - 34 SP - 217 EP - 223 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-51677 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. A1 - Thomas, Sebastian T1 - Consequences of the reduced minimum burst pressure on the production surveillance N2 - First the acceptance rates resulting from the analysis of different minimum burst ratios and standards are displayed and explained. Especially the problems resulting from a further reduction if the minimum burst ratio are shown. For a better understanding of these results the process of analysing the acceptance rate is explained in detail. This contains the alleged contradiction between safety of samples due to its scatter while the rejected sample provides a higher mean strength. Then the importance of batch testing is explained and leads to the recommendation to have a strong interaction between provided mean strength and requested maximum of production scatter. T2 - 8 th WG on rev GTR 13 CY - Online meeting DA - 02.03.2020 KW - Minimum burst ratio KW - Production scatter KW - Mean burst pressure KW - Batch testing KW - Acceptance rate PY - 2020 AN - OPUS4-53147 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Bergungsdruckgefäße - Vorschlag zur Definition von Druckgefäßen N2 - Es wird plastisch dargestellt, mit welcher Intention und welchem Ziel Deutschland in die Juni Sitzung des UN ECOSOC SubCom TDG gehen wird, um ein Druckvolumenbegrenzung für Druckgefäße zu erreichen. T2 - BAM-DIN-IGV-DVFG-Jahresgespräch 2020 CY - Berlin, Germany DA - 27.02.2020 KW - Bergungsdruckgefäß KW - Konsequenzbegrenzung KW - Volumenbegrenzung KW - Druck-Volumen-Produkt KW - UN-Modellvorschriften KW - Akzeptanz PY - 2020 AN - OPUS4-53146 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -