TY - CONF A1 - Sobol, Oded T1 - Challenges with metallic materials in H 2 technologies N2 - Increasing environmental problems with conventional energy technology are stimulating the demand for alternative energy solutions. With air quality reaching catastrophic levels in large cities worldwide, Fuel Cell Electric Vehicles offer the ideal combination of clean power with the amenities of electric drives. Hydrogen use on vehicles, nevertheless, also raises some issues about safe handling. As fuel cells and hydrogen applications, including vehicles, approach technological maturity, developing their business cases becomes crucial in introducing them to the consumer markets. The Joint European Summer School JESS 2021 addresses these issues by offering high quality graduate level courses on selected topics of vehicle technology, innovation & business development, safe handling of hydrogen, and modelling. This series of summer schools has been ongoing since 2004 and targets an audience of university students (MSc and PhD levels) and post-doctoral researchers. We also welcome more experienced researchers and engineers wishing to expand their general knowledge, for instance, to suit a newly acquired position or collect credits for Continuous Professional Development (CPD). The course content is tailored to the needs of a diverse audience: newcomers to the field, experienced students, and young professionals working at the forefront of fuel cell and hydrogen applications. T2 - Joint european summer school (JESS) CY - Online meeting DA - 06.09.2021 KW - Hydrogen Embrittlement KW - Hydrogen assisted cracking KW - Gaseous hydrogen PY - 2021 UR - https://www.jess-summerschool.eu/Week-2 SP - 1 EP - 41 AN - OPUS4-53402 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reichel, Levin T1 - Reparaturschweißen in der schweißtechnischen Montage: Moderne Schweißverfahren für hochfeste Offshore-Stähle N2 - Der Ausbau der Offshore-Windenergie mit Anlagenleistungen von über 10 MW er-fordert zunehmend den Einsatz hochfester Stähle mit Streckgrenzen ab 460 MPa bei Wanddicken von bis zu 150 mm. Inakzeptable Defekte, die während bzw. nach der schweißtechnischen Montage solcher dickwandigen Verbindungen im Nahtbereich detektiert werden, können wirtschaftlich durch lokales Ausfugen und anschließendes Schweißen noch in der Fertigung repariert werden. Insbesondere bei hochfesten Baustählen stellt dies hohe Anforderungen an die schweißtechnische Fertigung, da bislang keine standardisierten Reparaturkonzepte oder normativen Vorgaben existie-ren. Praxisnahe Empfehlungen sind hier vor allem für kleine und mittlere Unterneh-men (KMU) notwendig, damit diese Reparaturschweißungen sicher und wirtschaft-lich durchführen können. Die laufende Untersuchung (FOSTA P1629/IGF 01IF22746N) legt daher den Schwerpunkt auf die Optimierung der Reparaturverfahren mit dem Ziel, schweißbe-dingte Beanspruchungen zu reduzieren, weil diese häufig zu erneuten Bildung Fehl-stellen führen. Hierfür werden hochfeste, dickwandige Verbindungen aus Offshore-Stahlgüten im Streckgrenzenbereich von 355 MPa bis 460 MPa untersucht. Die ex-perimentellen Analysen berücksichtigen dabei die komplexen Wechselwirkungen zwischen werkstoff- und prozess- sowie konstruktionsbedingten Einflüssen auf den Beanspruchungszustand nach dem Schweißzyklus (Verbindungsschweißen, Ausfu-gen, Reparaturschweißen). Diese Faktoren, wie z. B. die Steifigkeitsverhältnisse der Schweißnaht, sind von entscheidender Bedeutung für die resultierenden Eigenspan-nungen, die sich infolge der schweißtechnischen Reparatur ausbildet. Um die Bau-teilsicherheit und Leistungsfähigkeit zu gewährleisten, sind insbesondere risskriti-sche, mehrachsige Eigenspannungszustände zu vermeiden. So lassen sich moderne Hochleistungs-MAG-Schweißprozesse mit hierfür optimierten, schmaleren Fugen-geometrien in bauteilbezogenen Schweißversuchen auf Großprüfanlagen untersu-chen, um hierfür angepasste Prozess- und Wärmeführungsparameter zu identifizie-ren und angepasste Reparaturkonzepte abzuleiten. Ziel ist es, Handlungsempfehlun-gen für Richtlinien und Normen zu erarbeiten, die das Potenzial hochfester Stähle voll ausschöpfen und die Anwendbarkeit im Offshore-Stahlbau, insbesondere für KMU, substanziell stärken. Auf diese Weise leistet das Projekt einen entscheiden-den Beitrag zur erfolgreichen Umsetzung der Energiewende in Deutschland. T2 - Forschungsseminar OVGU-Magdeburg CY - Magdeburg, Germany DA - 18.06.2025 KW - Moderne Schweißprozesse KW - Offshore KW - Reparaturschweißen KW - Thermisches Ausfugen KW - Eigenspannungen KW - Gefügedegradation PY - 2025 AN - OPUS4-65238 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröpfer, Dirk T1 - Ultraschallunterstütztes Fräsen innovativer metallischer Werkstoffe zur Optimierung von Oberflächenintegrität und Werkzeugverschleiß Neueste Erkenntnisse und Perspektiven im Kontext der Komponentensicherheit N2 - Der Vortrag behandelt ultraschallunterstütztes Fräsen als innovative Technologie zur Bearbeitung schwer zerspanbarer metallischer Werkstoffe und deren Einfluss auf Oberflächenintegrität, Werkzeugverschleiß und Komponentensicherheit. Ausgangspunkt ist die Herausforderung durch hohe Festigkeit, heterogene Gefüge und Eigenspannungen bei konventioneller und additiver Fertigung (z. B. Ni-, Co-Legierungen, Eisen-Aluminide). Diese Faktoren führen zu erhöhten Prozesskräften, Werkzeugverschleiß und nachteiligen Oberflächeneigenschaften. Ultraschallunterstützung reduziert Zerspankräfte, stabilisiert Prozesse bei AM-Bauteilen und verbessert die Oberflächengüte durch Einbringung von Druckeigenspannungen. Untersuchungen zeigen: Optimale Amplituden (ca. 4 µm) minimieren Eigenspannungen und Defekte, erhöhen die Ermüdungsfestigkeit und verlängern die Werkzeugstandzeit. Bei Eisen-Aluminiden und DED-Arc-gefertigten Bauteilen konnten deutliche Verbesserungen in Rauheit, Kraftverlauf und Verschleiß erzielt werden. Für Co-/Ni-Legierungen wurde zusätzlich die Wirksamkeit durch Legierungsmodifikation nachgewiesen. Perspektivisch bietet die Technologie Potenzial für Lebensdauersteigerung hochfester Bauteile, Integration von Oberflächenverfestigung in den Fräsprozess und Reduktion von Nachbearbeitungsschritten. Geplante Projekte adressieren Hochentropielegierungen, Mehrkomponentenwerkstoffe und hybride Fertigungsstrategien. Insgesamt zeigt sich, dass US-Fräsen eine Schlüsselrolle für ressourceneffiziente, sichere und leistungsfähige Komponenten in Leichtbau und Hochtemperaturanwendungen einnehmen kann. T2 - 4. Wissenschaftliches Forum zur ULTRASONIC-Bearbeitung CY - Jena, Germany DA - 12.11.2025 KW - Ultraschallunterstütztes Fräsen KW - Oberflächenintegrität KW - Werkzeugverschleiß KW - Zerspankräfte KW - Additive Fertigung (DED-Arc, AM) KW - Eisen-Aluminid KW - Co-/Ni-Legierungen KW - Ermüdungsfestigkeit KW - Eigenspannungen KW - Lebensdauersteigerung KW - Hybridfertigung KW - Hochentropielegierungen (MPEA) PY - 2025 AN - OPUS4-65240 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröpfer, Dirk T1 - Begrüßung und Vorstellung der BAMund des Fachbereichs 9.2 - Zentrale Forschungswerkstatt N2 - Die Zentralwerkstatt der BAM übernimmt die Fertigung und Konstruktion komplexer Prüf- und Versuchseinrichtungen und adressiert zugleich zentrale Forschungsthemen zur Werkstoff- und Komponentensicherheit. Dazu gehören die Entwicklung innovativer Fertigungstechnologien, ressourceneffiziente Verarbeitungskonzepte für hochfeste und additive Komponenten sowie die Untersuchung von Fertigungseinflüssen auf Oberflächenintegrität und Werkstoffdegradation. Ein besonderer Fokus liegt auf der H₂-Sicherheit, insbesondere der Fertigung und Prüfung von Hohlzugproben für Wasserstoff-Pipelines. Ergänzend werden Automatisierungslösungen, digitale Methoden und moderne Spanntechnik zur Effizienzsteigerung eingesetzt. Die Arbeiten sind eng mit den BAM-Kompetenzzentren AM@BAM, H2Safety@BAM und WIND@BAM verzahnt und leisten einen Beitrag zur Energiewende sowie zur Normung und zum Technologietransfer. T2 - 37. Stammtisch Metall des "Der Mittelstand BVMW e.V. " CY - Berlin, Germany DA - 17.09.2025 KW - Werkstoffsicherheit KW - H₂-Sicherheit KW - Additive Fertigung KW - Ressourceneffizienz KW - Automatisierung in der Fertigung KW - Prüftechnikentwicklung KW - Normung und Technologietransfer KW - Oberflächenintegrität PY - 2025 AN - OPUS4-65245 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröpfer, Dirk T1 - HGF-AK "Bau wissenschaftlicher Geräte" - Neues aus der BAM / Fachbereich 9.2 N2 - In dieser Präsentation werden die neuesten Herausforderungen und der Stand des Fachbereiches 9.2 für die Mitarbeit im AK des HGF "Bau wissenschaftlicher Geräte" dargestellt. Hierfür werden Neuigkeiten aus dem Bereich Materialprüfung in der BAM präsentiert und mit den Arbeiten der Zentralwerkstatt, die hierfür notwendig sind, in Zusammenhang gebracht. T2 - 20. Jahrestagung des Helmholtz-Arbeitskreis "Bau wissenschaftlicher Geräte" CY - Jülich, Germany DA - 07.05.2025 KW - Fertigungskompetenz KW - Fertigungsverfahren PY - 2025 AN - OPUS4-65243 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reichel, Levin T1 - Optimising repair welding: narrower groove design for modern welding processes on high-strength offshore steels N2 - The ongoing energy transition in Germany requires large offshore wind turbines with outputs over 10 MW and suitable deep-water subsea structures. Large towers made of high-strength steel with a yield strength of up to 500 MPa are needed to use the mate-rial more efficiently, enabling thinner wall sections without compromising structural integrity. This places high demands on manufacturers, especially regarding welding high-strength offshore steels. Weld defects detected through non-destructive testing (NDT) must be repaired by gouging and rewelding during fabrication. For thick plate joints, there is a notable lack of research, repair strategies, and guidance in standards and guidelines. Safe and cost-effective repairs are urgently necessary to support manufacturers, particularly SMEs. This study focuses on high-strength thick plate joints made of offshore grades with a yield strength of 355 to 460 MPa, repaired us-ing optimised narrow gouging grooves and controlled high-performance GMAW pro-cesses. Experimental analyses examine the complex interaction between the welding process, material properties, and design influences on the formation of weld-induced residual stresses in high-strength fine-grain structural steels. To ensure the safety and performance of components, it is essential to prevent repair welding-related material degradation and the development of crack-critical residual tensile stresses. In this investigation, gouging was carried out using milling to ensure reproducibility. The restraint intensity of the groove significantly increases with a shorter groove length and a thicker substrate. The relaxation caused by the gouging process was ana-lysed using X-ray diffraction (XRD) to examine the initial conditions for the subse-quent repair welding. The residual stresses induced by the repair welding were ana-lysed, and different groove configurations have been compared. With shorter groove lengths and wider opening angles, the residual stresses after the repair weld increase markedly for this analysed offshore steel. The lowest residual stresses can be achieved by increasing the groove length and reducing the opening angle for a repair weld with a modern, controlled welding process. Adapting the repair process and boundary conditions allows for the full utilisation of the material's potential. This makes a valuable contribution to the energy transition in Germany, especially for SMEs in the steel processing industry. T2 - Forschungsseminar OVGU-Magdeburg CY - Magdeburg, Germany DA - 10.12.2025 KW - Repair welding KW - Narrow groove KW - Controlled arc KW - Residual stress KW - High-strength offshore steel PY - 2025 AN - OPUS4-65239 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witte, Julien T1 - Safety for H2 Transport in Welded Low-Alloy Gas Pipelines N2 - Steel gas pipelines are to be used in the future for the transport of hydrogen (H) or for its blending in natural gas. For the use of existing pipeline systems, as well as their adaptation and expansion with modern steels to the end user, it is necessary to investigate the extent to which hydrogen is absorbed by the material or welded joints, depending on the gas composition and changing temperature and pressure stresses, and can reduce their ductility, in order to exclude an unexpected brittle failure in the form of hydrogen-assisted cracking. So far, in-situ tests of H-absorption under continuous mechanical stress have been carried out using slow strain rate tests (SSRT) with full-section test specimens in high-pressure autoclaves. The high safetyrelated laboratory costs associated with this prevent cost-effective series testing for industry. Initial studies show that hollow tensile specimens (HTS) SSRT are a viable alternative through the defined adjustment of gases and pressures via the inner bore hole. To this end, the following key questions need to be addressed, (1) representation of real stress scenarios of welded pipes on HTS, (2) the effect of the gas composition (H2/CH4) on H absorption and degradation, (3) the influences and interaction of different weld seam structures under continuous and cyclically changing stress, (4) the possibility of integrating into a practical test concept for the evaluation of welded steels, and (5) the material behaviour of existing pipelines compared to modern steels. This work, which is being carried out as part of the IGF project no. 22884, focuses on a systematic investigation of the boundary conditions temperature, pressure and H2 partial pressure as well as steel grade and strain rate in correlation with realistic conditions. The experimental investigations show significant, and in dependence of the strain rate, different pronounced effects, in particular due to the temperature and the H2 partial pressure on the deformation capacity of the examined materials. With this, the technology should be further developed for further questions, in particular with regard to weld microstructure, in order to establish a simple, economical test procedure based on HZP-SSRT with regard to the H-readiness of welded steel pipelines by means of corresponding guidelines and transfer to standards. Ultimately, users, especially SMEs such as testing laboratories, should be involved in the development of the hydrogen economy as part of the energy transition, which underlines the high relevance for society as a whole. T2 - 5th International Conference on Metals and Hydrogen CY - Ghent, Belgium DA - 14.10.2025 KW - Hydrogen safety / transport KW - Welded hydrogen pipeline safety / integrity KW - Hollow tensile specimens (HTS) KW - Slow strain rate testing (SSRT) KW - High-strength steel PY - 2025 AN - OPUS4-65236 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Namwoonde, Andreas Sheuyange T1 - Polymer Composites Under Continuous and Reciprocating Sliding Conditions In Hydrogen N2 - The implementation of hydrogen as an alternative energy source to fossil fuels necessitates the use of compatible materials for safety purposes, and thermoplastics are widely utilized in this context. The application of polymers in gaseous and liquid hydrogen environments requires careful consideration of their tribological performance, as the operating environment is dramatically different from ambient conditions. Friction, wear, and lubrication are crucial factors to consider in this regard. Researchers have investigated various strategies to enhance the tribological performance of polymers in hydrogen environments, including modifying the composition and structure of polymers by incorporating fillers to improve their friction and wear resistance. The tribological properties of polymer composites based on matrices of PEEK, PPS, and PI have been mostly investigated using the continuous sliding test method, and the results indicate that these materials are suitable candidates for tribological applications in both gaseous and liquid hydrogen. This project explores the tribological properties of related polymer composites in hydrogen using continuous and reciprocating motion with a pin-on-disc testing method. T2 - Polytrib2024 CY - Portorož, Slovenia DA - 03.10.2024 KW - Polymers KW - Friction KW - Wear KW - Tribological behaviour KW - Hydrogen PY - 2024 AN - OPUS4-61378 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mente, Tobias A1 - Grimault de Freitas, Tomás A1 - Nietzke, Jonathan A1 - Konert, Florian A1 - Sobol, Oded A1 - Wackermann, Ken A1 - Ruchti, Peter A1 - Elsen-Humberg, Stefan A1 - Systermans, Thomas ED - Zimmermann, Martina T1 - Hohlzugprüfung als kostengünstige Methode zur Werkstoffcharakterisierung für die Wasserstoffwirtschaft N2 - Wasserstoff ist ein notwendiger Baustein zur Erreichung zukünftiger Klimaziele. Für eine schnell hochlaufende Wasserstoffwirtschaft ist es daher notwendig sowohl bestehende Infrastruktur als auch neue Werkstoffe für den sicheren und nachhaltigen Einsatz in Wasserstofftechnologien zu qualifizieren. Die akzeptierten und standardisierten Prüfverfahren zur Ermittlung des Einflusses gasförmigen Wasserstoffs auf die mechanischen Eigenschaften metallischer Werkstoffe sind meist sehr komplex, mit hohem technologischem und finanziellem Aufwand verbunden und stehen nur Wenigen Instituten weltweit zur Verfügung. Die Hohlzugprüftechnik bietet hier eine kostengünstige und einfach zu realisierende Alternative. Mit der im Jahr 2024 erstmals veröffentlichten ISO 7039 wurde diese Prüftechnik auch für die Wirtschaft anwendbar gemacht. Der Standard gilt allgemein für die Prüfung mit gasförmigen Medien, weist jedoch in Bezug auf die Prüfung mit gasförmigem Wasserstoff noch einige Wissenslücken auf. Im Teilvorhaben H2HohlZug des Leitprojekt TransHyDE werden die Lücken zum Einfluss der Geometrie, Oberflächenqualität sowie Gasreinheit in einzelnen Arbeitspaketen geschlossen und die Erkenntnisse in einen Standard überführt. T2 - 43. Vortrags- und Diskussionstagung Werkstoffprüfung 2025 - Werkstoffe und Bauteile auf dem Prüfstand CY - Dresden, Germany DA - 27.11.2025 KW - Hohlzugprüfung KW - Druckwasserstoff KW - ISO 7039 KW - H2HohlZug - TransHyDE PY - 2025 SN - 978-3-88355-454-9 SP - 11 EP - 17 PB - Deutsche Gesellschaft für Materialkunde e.V. (DGM) CY - Dresden AN - OPUS4-64937 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - From Research to a Standard: The Hollow Specimen Technique for High-Pressure Hydrogen Gas Testing N2 - As the world moves towards a decarbonised economy, the demand for sustainable and low-carbon alternatives is growing rapidly. Hydrogen has an important role to play in this transition, but in order to make the most of hydrogen as an energy carrier, a comprehensive understanding of its impact on the integrity of structural materials is necessary. Metallic materials, mainly steels, are the most commonly used structural materials in various components throughout the hydrogen supply chain. Ensuring their sustainable and safe use in hydrogen technologies is a crucial factor in the development of the hydrogen economy. This is particularly important since hydrogen can promote crack formation and ultimately lead to premature failure in these materials when combined with mechanical load. This process is commonly known as Hydrogen Embrittlement and can occur in almost all the steels used for the hydrogen technologies. Extensive materials qualification is required for the rapid implementation of hydrogen technologies, however, most accepted, and standardised test methods for determining the effect of gaseous hydrogen on metallic materials describe complex and costly procedures that are only available to a very limited extent worldwide. The hollow specimen technique is a simple and economical method that has the potential to overcome the limitations of the current methods and complement them for qualifying metallic materials under high-pressure hydrogen gas. Unlike the conventional autoclave technique, this method requires significantly lower amounts of hydrogen, resulting in fewer safety measures and no need for complex equipment or a specialised laboratory. The technique's low investment and testing costs, simple operation, and shorter testing time make it an optimal for widespread use around the world, thereby increasing the output of results. Initial studies have demonstrated the feasibility of assessing hydrogen effects in metallic materials using the hollow specimen technique. This led to the establishment of an ISO committee to standardise the method. However, there are open questions that currently prevent the technique from being standardised for hydrogen testing. These open questions relate to specimen geometry, inner hole surface and gas quality and are being addressed in the H2HohlZug project, of which the overall aim is to systematically close the gaps towards a standard. This contribution presents the structure and milestones of the project, followed by initial results. T2 - CETIM Workshop Technique H2 CY - Nantes, France DA - 11.12.2025 KW - Hydrogen KW - Hydrogen Embrittlement KW - Hollow Specimen Technique KW - High-Pressure Gaseous Hydrogen KW - TransHyDE KW - H2HohlZug KW - Standardisation PY - 2025 AN - OPUS4-65103 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - Hollow Specimen Method for Tests in High-Pressure Hydrogen Gas: The Role of Geometry, Surface Quality and Gas Purity N2 - The hollow specimen technique is a simple and cost-effective method that has the potential to make materials qualification with pressurised gaseous hydrogen widely accessible to academia and industry. The feasibility of this method for slow strain tensile tests has been demonstrated in several studies, leading to the establishment of the ISO/TC 164/SC 1/WG 9 ISO committee for its standardisation. Questions have emerged during this process, that currently prevent the method from being standardised for hydrogen testing. These questions relate to specimen geometry, specimen manufacturing and gas quality and are being systematically addressed in the TransHyDE-H2HohlZug project. The first results are presented in this poster. T2 - TransHyDE Vollversammlung 2024 CY - Leipzig, Germany DA - 27.11.2024 KW - Hydrogen KW - Hydrogen Embrittlement KW - Hollow Specimen Technique KW - High-Pressure Gaseous Hydrogen KW - Austenitic Stainless Steel KW - TransHyDE KW - H2HohlZug PY - 2024 AN - OPUS4-61847 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Hydrogen - Trust through safety N2 - In den Virtual Talks der DECHEMA wurden allgemeine Aspekte der Sicherheit und Akzeptanz von Wasserstofftechnologien vorgestellt. Wie kann Vertrauen in neue Technologien geschaffen werden, wenn Unfälle aus der Vergangenheit zu Mythen und Märchen führten? Der Vortrag räumt mit allgemeinen Vorurteilen auf und zeigt, dass der Umgang mit Wasserstoff weder unsicherer, noch sicherer ist als der Umgang mit anderen Brenngasen. Basis für den sicheren Umgang mit Wasserstoff ist immer eine Risikoanalyse. N2 - In the DECHEMA Virtual Talks, general aspects of the safety and acceptance of hydrogen technologies were presented. How can trust in new technologies be built when past accidents led to myths and fairy tales? The presentation does away with general prejudices and shows that handling hydrogen is neither more unsafe nor safer than handling other fuel gases. The basis for the safe handling of hydrogen is always a risk analysis. T2 - DECHEMA Virtual Talks CY - Online meeting DA - 23.11.2020 KW - Hydrogen KW - Wasserstoff KW - Safety KW - Sicherer Umgang KW - Sicherheit PY - 2020 AN - OPUS4-52082 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nietzke, Jonathan T1 - Performance of Conventional and Additive Manufactured Austenitic Stainless Steels under Gaseous Hydrogen Environment using in-situ Hollow Specimen Technique N2 - Hydrogen and its derivatives (e.g. ammonia) are considered as a suitable energy carrier in the future supply of renewable energy. Hydrogen transportation systems require pipes, valves and fittings, among other components. In this sense, austenitic stainless steels are commonly used structural materials for pure hydrogen applications. Stable austenitic alloys, like AISI 316L, are often assumed to be practically unsusceptible to hydrogen embrittlement. At the same time, a number of studies show the influence of hydrogen even in 316L under some circumstances. Some other studies state that this embrittlement could be avoided by using steel grades with a higher nickel equivalent which contributes to a more stable austenitic phase. Nonetheless, 316L is widely used in hydrogen atmospheres since many years because of lower costs and positive practical experience. For these reasons, not only 316L but also 304 could be further utilized by identifying the exact constraints. With increasing demand for components regarding hydrogen applications, additive manufacturing technologies are getting increasingly important complementary to conventional manufacturing. In the context of additive manufacturing, 316L is a common material as well. The manufacturing process offers great advantages due to higher freedoms in design and the possibility for customized components in small batches. For example, valves with improved flow characteristics and reduced component weight can be produced. Nevertheless, there is still lack of experience and experimental results concerning additively manufactured parts under hydrogen service. Therefore, the influence on the material properties for additively manufactured parts in hydrogen environments needs to be further investigated. In the present work, slow strain rate testing (SSRT) has been applied using hollow specimens. This testing procedure allows to perform practicable and faster in-situ tests in comparison to tests in autoclaves and investigate the influence of hydrogen on the mechanical properties. Conventional AISI 304 and 316L specimens as well as additively manufactured 316L specimens were tested at room temperature and a pressure of 200 bar. Elongation at fracture and relative reduction of area (RRA) have been used to evaluate the influence of hydrogen. It is shown that the influence of hydrogen is more pronounced in 304 than in 316L. Furthermore, potentially influencing factors such as surface roughness, microstructure and porosity are discussed. T2 - International Hydrogen Conference CY - Park City, Utah, USA DA - 17.09.2023 KW - Hydrogen KW - Hollow Specimen Technique KW - Additive Manufacturing KW - Austenitic Steels PY - 2023 AN - OPUS4-58776 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Konert, Florian T1 - Investigation of the resistance of X65 pipeline steel and weld to gaseous hydrogen using the hollow specimen technique N2 - The constantly increasing demand for renewable energy sources lead to the necessity of transporting large amounts of hydrogen. Since pipelines enable a cost-effective way for the distribution of gaseous hydrogen, the interaction of hydrogen and the pipeline materials must be carefully investigated as hydrogen can cause a degradation of the mechanical properties under certain conditions. Especially welds, which are assumed to be more susceptible to the degradation enhanced by hydrogen, are of great interest. The aim of this study is to investigate the effect of gaseous hydrogen on the mechanical properties of an X65 pipeline, and the longitudinal submerged arc welding (SAW) welded joint. The tests are conducted using the hollow specimen technique on two types of specimens: one extracted from the base material (BM) and the other extracted as a cross-weld (CW) specimen consisting of base material and weld seam. The specimens are charged in-situ under a pressure of 60 bar and tested using slow strain rate (SSR) tensile tests with a nominal strain rate of 10-5 s-1. The performed tests showed a decrease of the reduction of area (RA) from 72% in inert atmosphere to 52% in hydrogen atmosphere for the CW-specimen and a decrease from 73% in inert atmosphere to 51% for the BM. Metallographic analyses showed the crack initiation between fine grain heat affected zone (FGHAZ) and BM for the specimens tested in hydrogen atmosphere as well as for the reference specimens. This leads to the conclusion that the location of the crack initiation does not change due to the presence of gaseous hydrogen. T2 - 77th IIW Annual Assembly and International Conference 2024 CY - Rhodes, Greece DA - 07.07.2024 KW - Hydrogen KW - Hollow-specimen KW - Pipeline steel KW - SSRT KW - Hydrogen embrittlement PY - 2024 AN - OPUS4-60617 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mente, Tobias T1 - Hohlzugprüfung - Kostengünstige Methode zur Werkstoffcharakterisierung für die Wasserstoffwirtschaft N2 - Wasserstoff ist ein notwendiger Baustein zur Erreichung zukünftiger Klimaziele. Für eine schnell hochlaufende Wasserstoffwirtschaft ist es daher notwendig sowohl bestehende Infrastruktur als auch neue Werkstoffe für den sicheren und nachhaltigen Einsatz in Wasserstofftechnologien zu qualifizieren. Die akzeptierten und standardisierten Prüfverfahren zur Ermittlung des Einflusses gasförmigen Wasserstoffs auf die mechanischen Eigenschaften metallischer Werkstoffe sind meist sehr komplex, mit hohem technologischem und finanziellem Aufwand verbunden und stehen nur Wenigen Instituten weltweit zur Verfügung. Die Hohlzugprüftechnik bietet hier eine kostengünstige und einfach zu realisierende Alternative. Mit der im Jahr 2024 erstmals veröf-fentlichten ISO 7039 wurde diese Prüftechnik auch für die Wirtschaft anwendbar gemacht. Der Standard gilt allgemein für die Prüfung mit gasförmigen Medien, weist jedoch in Bezug auf die Prüfung mit gasförmigem Wasserstoff noch einige Wissenslücken auf. Im Teilvorhaben H2HohlZug des Leitprojekt TransHyDE werden die Lücken zum Einfluss der Geometrie, Ober-flächenqualität sowie Gasreinheit in einzelnen Arbeitspaketen geschlossen und die Erkenntnisse in einen Standard überführt. T2 - 43. Vortrags- und Diskussionstagung Werkstoffprüfung 2025 - Werkstoffe und Bauteile auf dem Prüfstand CY - Dresden, Germany DA - 27.11.2025 KW - Hohlzugprüfung KW - Druckwasserstoff KW - ISO 7039 KW - H2HohlZug - TransHyDE PY - 2025 AN - OPUS4-64936 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - Hollow Specimen Method for Tests in High-Pressure Hydrogen Gas: The TransHyDE - H2HohlZug Project N2 - The feasibility of the method for slow strain tensile tests has been demonstrated in several studies, leading to the establishment of the ISO/TC 164/SC 1/WG 9 ISO committee for its standardisation. Questions have emerged during this process, that currently prevent the method from being standardised for hydrogen testing. These questions relate to specimen geometry, specimen manufacturing and gas quality and are being systematically addressed in the TransHyDE-H2HohlZug project. T2 - TrasnsHyDE Abschlusskonferenz CY - Berlin, Germany DA - 25.03.2025 KW - Hydrogen KW - Hydrogen Embrittlement KW - Hollow Specimen Technique KW - High-Pressure Gaseous Hydrogen KW - TransHyDE PY - 2025 AN - OPUS4-62807 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Konert, Florian A1 - Freitas, Tomás T1 - 5. Vollversammlung TransHyDE N2 - Die im Jahr 2025 abgeschlossenen Meilensteine des Projektes H2HohlZug werden präsentiert. Diese umfassen die nationale Einigung auf eine Probengeometrie sowie die Testbedingungen. Weiter wurde ein Normentwurf in das ISO-Gremium eingebracht. Die begleitenden Publikationen in Fachzeitschriften sowie Beteiligungen an Konferenzen werden zusammengefasst. Abschließend wird der Ablauf des internationalen Round-Robins beschrieben und der Transfer der Kenntnisse in den Normungsprozess erläutert.“ T2 - 5. TransHyDE Vollversammlung CY - Leipzig, Germany DA - 26.11.2025 KW - Hohlzugprobe KW - TransHyDE KW - Norm PY - 2025 AN - OPUS4-64976 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael T1 - Mechanische Eigenschaften der Längschweißnaht einer X65-Pipeline in Druckwasserstoffatmosphäre N2 - Im folgenden Beitrag werden die Ergebnisse der mechanischen Eigenschaften unter 200 bar Druckwasserstoff des Werkstoffes 316L (1.4404) vorgestellt. Dazu wurden Hohlzugproben aus konventionellem, kaltgezogenem Material herausgearbeitet und per SLM-PBF additiv gefertigten Hohlzugproben gegenübergestellt. Die Proben wurden da-bei unter Druckwasserstoff einer SSRT-Prüfung mit einer Dehnrate von 1E-5/s unterzogen. Zusätzlich zum Werkstoffzustand wurde der Einfluss des Oberflächenzustandes charakterisiert: (1) additiv gefertigten Proben mit endkonturnaher Form „as-printed“ oh-ne zusätzliche Bohrung, (2) Bohren und (3) zusätzliches Honen. Die gemessene Degradation der mechanischen Eigenschaften unter Wasserstoff hing dabei in erster Linie von der Oberfläche ab und damit indirekt vom Werkstoffzustand „as-printed“ oder kaltgezogen ab. Während die Proben mit gebohrter und/oder gehonter Oberfläche eine RRA (Relative Reduction of Area) 78 % aufwiesen, zeigten die AM-Proben eine deutlich höhere RRA von 90 %. Ein möglicher Grund dafür sind während der Fertigung ausbildende Oxidschichten, die sich durch geringe Mengen an Restsauerstoff während des AM-Prozesses ausbilden. Zur abschließenden Charakterisierung sind weitere Untersuchungen erforderlich, insbesondere für ein größeres Parameterfeld an Prüftemperaturen (Oxideinwirkung) und Dehnraten (mechanische Beständigkeit der Oxidschicht ähnlich den Einflüssen auf „klassische“ Spannungsrisskorrosion). T2 - DGM Arbeitskreis Wasserstoff CY - Neu-Isenburg, Germany DA - 26.05.2025 KW - Pipeline KW - Wasserstoff KW - Hohlzugprobe PY - 2025 AN - OPUS4-63236 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Konert, Florian A1 - Nietzke, Jonathan T1 - Application of an in-situ H2Test Method N2 - The degradation effect of hydrogen on the mechanical properties of steels is well known, but still not sufficiently understood. The fast and safe market ramp up of hydrogen technologies makes it evident to evaluate a wider understanding of this topic. In general it is often described as hydrogen embrittlement. Therefore it is desirable to achieve a test method which is able to provide material properties under hydrogen atmosphere in an easy way. Currently mechanical tests under hydrogen atmosphere are executed in autoclaves. For this technique complex hardware is needed, therefore tests are expensive and test capacities are only available in a small scale. The shown test method promises a trendsetting approach for reducing costs and machine time by using hollow specimen. T2 - 4th International Conference on Metals and Hydrogen - Steely & Hydrogen 2022 CY - Ghent, Belgium DA - 11.10.2022 KW - Hydrogen KW - Hollow specimen KW - In-situ KW - Test procedure PY - 2022 AN - OPUS4-56032 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - Hollow Specimen Method for Tests in High-Pressure Hydrogen Gas: The Role of Strain-Rate and Surface Quality N2 - As the world moves towards a decarbonised economy, the demand for sustainable and low-carbon alternatives is growing rapidly. Hydrogen has an important role to play in this transition, but in order to make the most of hydrogen as an energy carrier, a comprehensive understanding of its impact on the integrity of structural materials is necessary. Metallic materials, mainly steels, are the most commonly used structural materials in various components throughout the hydrogen supply chain. Ensuring their sustainable and safe use in hydrogen technologies is a crucial factor in the development of the hydrogen economy. This is particularly important since hydrogen can promote crack formation and ultimately lead to premature failure in these materials when combined with mechanical load. This process is commonly known as Hydrogen Embrittlement and can occur in almost all the steels used for the hydrogen technologies. Extensive materials qualification is required for the rapid implementation of hydrogen technologies, however, most accepted, and standardised test methods for determining the effect of gaseous hydrogen on metallic materials describe complex and costly procedures that are only available to a very limited extent worldwide. The hollow specimen technique is a simple and economical method that has the potential to overcome the limitations of the current methods and complement them for qualifying metallic materials under high-pressure hydrogen gas. Unlike the conventional autoclave technique, this method requires significantly lower amounts of hydrogen, resulting in fewer safety measures and no need for complex equipment or a specialised laboratory. The technique's low investment and testing costs, simple operation, and shorter testing time make it an optimal for widespread use around the world, thereby increasing the output of results. Initial studies have demonstrated the feasibility of assessing hydrogen effects in metallic materials using the hollow specimen technique. This led to the establishment of an ISO committee to standardise the method. However, there are open questions that currently prevent the technique from being standardised for hydrogen testing. These open questions relate to specimen geometry, inner hole surface and gas quality and are being addressed in the H2HohlZug project, of which the overall aim is to systematically close the gaps towards a standard. This contribution presents the structure and milestones of the project, followed by initial results. T2 - HyLab | HyTalks CY - Online meeting DA - 12.11.2025 KW - Hydrogen KW - Hydrogen Embrittlement KW - Hollow Specimen Technique KW - High-Pressure Gaseous Hydrogen KW - TransHyDE KW - H2HohlZug PY - 2025 AN - OPUS4-64749 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -