TY - CONF A1 - Theiler, Geraldine T1 - Effect of temperature on the friction behaviour of rubber materials in hydrogen N2 - Safety and reliability are the major challenges to face for the development and acceptance of hydrogen technology. It is therefore crucial to study deeply material compatibility, in particular for tribological components that are directly in contact with hydrogen. Some of the most critical parts are sealing components that face high risk of damage due variation of pressure, temperature and mechanical stress. In this study, the friction and wear behaviour of several rubber materials was evaluated in hydrogen environment at ambient and low temperature. Tests were performed against 316L disks in a reciprocation motion. Results reveal that the hydrogen affects the friction and wear behaviour of most materials. The friction mechanism is dominated by deformation for most rubber materials at ambient temperature while sliding occurs at low temperature due to the increased hardness of the rubbers. T2 - Polytrib 2024 CY - Portorož, Slovenia DA - 03.10.2024 KW - Reciprocating sliding KW - Rubber materials KW - Hydrogen KW - Low temperature PY - 2024 AN - OPUS4-62019 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Wasserstoff - Energieträger der Zukunft N2 - Im Rahmen des internationalen Wissenschaftsfestivals, der Berlin Science Week 2021, hat die BAM in einem Beitrag das Kompetenzzentrum H2Safety@BAM, dessen Vision und die vier wissenschaftlichen Kompetenzfelder sowie den dort bearbeiteten Themen bzw. Projekten vorgestellt. T2 - Berlin Science Week 2021 CY - Berlin, Germany DA - 01.11.2021 KW - H2Safety@BAM KW - Materialeignung und -kompatibilität KW - Bauteilprüfung, -sicherheit und -zertifizierung KW - Prozess- und Anlagensicherheit KW - Sensorik, Analytik und Referenzmaterialien KW - Sicherheit KW - Vertrauen in Wasserstofftechnologien PY - 2021 AN - OPUS4-55136 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Effect of high-pressure hydrogen environment on the physical and mechanical properties of elastomers N2 - This presentation deals with the exposure of HNBR rubbers to high pressure hydrogen (100 MPa) at 120 °C for 7 and 21 days under static conditions followed by characterization of their physical and mechanical properties.The core areas include swelling, rapid gas decompression, dynamic mechanical analysis (DMA), tensile strength and compression set properties. This study will assist in expanding the knowledge base of elastomer compatibility with hydrogen and therefore contribute significantly to the selection and development of polymer materials deploying hydrogen as a future energy carrier. T2 - EHEC European Hydrogen Energy Conferecne 2022 CY - Madrid, Spain DA - 18.05.2022 KW - Rubbers KW - Hydrogen KW - Characterization PY - 2022 AN - OPUS4-62084 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo T1 - Sensors for safety and process control in hydrogen technologies N2 - This tutorial provides an overview of the utilization of sensor systems in hydrogen technologies. It discusses the necessary criteria and characteristics of sensor systems, and also demonstrates practical applications of these technologies in terms of safety and process control. Emphasis is placed on various types of sensors such as gas sensors, pressure sensors, temperature sensors, and gas flow sensors. These systems find application in monitoring and regulating operational parameters, detecting potentially dangerous situations, and activating alarm systems. T2 - Sensor and Measurement Science International - SMSI 2023 CY - Nuremberg, Germany DA - 08.05.2023 KW - H2Safety@BAM KW - SensRef KW - Hydrogen KW - Gas sensor KW - Functional safety KW - Uncertainty KW - QI-Digital PY - 2023 AN - OPUS4-57532 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska A1 - Hofmann, Detlef A1 - Johann, Sergej A1 - Tiebe, Carlo A1 - Basedau, Frank A1 - Sturm, Patrick A1 - Lay, Vera A1 - Niederleithinger, Ernst T1 - Multi-sensor conception for safe sealing structures in underground repositories N2 - The project "SealWasteSafe" of the Bundesanstalt für Materialforschung und -prüfung (BAM, Berlin) deals with sealing structures applied for underground disposal of nuclear waste from two perspectives: (1) material improvement for application in sealing constructions and (2) feasibility study regarding multi-sensor approaches to ensure quality assurance and long-term monitoring. One specimen of 150 l made of alkali-activated material, which was found innovative and suitable for sealing constructions based on preliminary laboratory studies, and, for comparison purpose, another one made of salt concrete, are manufactured with an integrated multi-sensory setup for quality assurance and long-term-monitoring. The specimens were left in their cast form and additionally thermally insulated to simulate the situation in the repository. The multi-sensory concept comprises RFID technology embedded in the specimens suppling material temperature and moisture measurements, integrated fibre optic sensing allowing strain measurement and acoustic emission testing for monitoring possible crack formation. Overall, the suitability and the functionality of the sensors embedded into and attached to strongly alkaline (pH > 13 for the AAM) and salt corrosive (NaCl) environment was proven for the first 672 h. First temperature measurement based on RFID succeeded after 626 h for the alkali-activated material and after 192 h for the conventional salt concrete. Strain measurement based on distributed fibre optic sensing turned out the alkali-activated material with > 1 mm m-1 undergoing approximately twice the compression strain as the salt concrete with strains < 0.5 mm m-1. In contrast, the acoustic emission first and single hits representing crack formation in numbers, was found for alkali-activated material half of that detected at the salt concrete. T2 - SMIRT 26 CY - Berlin/Potsdam, Germany DA - 10.07.2022 KW - SealWasteSafe KW - Monitoring KW - Acoustic emission KW - Fibre optic sensing KW - RFID technology KW - alkali-activated material PY - 2022 SP - 1 EP - 10 AN - OPUS4-55371 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kröll, Mirco T1 - Harmonised tribological testing of polymers in hydrogen N2 - The focus of this work is to study the tribological performance of polymers in hydrogen atmosphere. Additionally, tests were carried out with up to three different tribometers at two institutions. The challenge to compare and harmonise equipment, procedures, and methods is an important part of the study. T2 - PolyTrib 2024 CY - Portoroz, Slovenia DA - 03.10.2024 KW - Hydrogen KW - Tribometer KW - Comparability KW - Harmonisation KW - Oil-coupled compounds PY - 2024 AN - OPUS4-61224 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Camplese, Davide A1 - Scarponi, Giordano Emrys A1 - Eberwein, Robert A1 - Hajhariri, Aliasghar A1 - Otremba, Frank A1 - Cozzani, Valerio T1 - Modelling Fire Response of Cryogenic Liquid Hydrogen Tanks Equipped with Multilayer Insulation (MLI) Systems N2 - In the context of the growing global interest in hydrogen-based green energy, cryogenic tanks equipped with multi-layer insulation (MLI) are emerging as a leading solution for storing hydrogen in vehicles. The integrity of these systems might be threatened during fire exposure. This can trigger the degradation of the MLI materials and induce rapid pressurization of the tank with a high risk of catastrophic failure. In this work, a novel lumped model to simulate the thermal response of MLI-equipped cryogenic liquid hydrogen tanks is presented. The model integrates the accurate database “Coolprop” for hydrogen thermodynamic properties and sub-models for detailed simulation of MLI degradation, providing a realistic simulation of the experimental data obtained under normal operating conditions. The application of the model to several case studies considering different numbers of MLI layers and tank geometries demonstrates that aluminum-based MLI offers scarce protection in case of exposure to a hydrocarbon poolfire. T2 - CISAP 11 CY - Neapel, Italy DA - 15.09.2024 KW - LH2 KW - LNG KW - Cryogenic storage tank KW - Insulation KW - MLI PY - 2024 DO - https://doi.org/10.3303/CET24111076 SN - 2283-9216 VL - 111 SP - 451 EP - 456 PB - AIDIC The Italian Association of Chemical Engineering AN - OPUS4-61384 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Camplese, Davide T1 - Modelling Fire Response of Cryogenic Liquid Hydrogen Tanks Equipped with Multilayer Insulation (MLI) Systems N2 - In the context of the growing global interest in hydrogen-based green energy, cryogenic tanks equipped with multi-layer insulation (MLI) are emerging as a leading solution for storing hydrogen in vehicles. The integrity of these systems might be threatened during fire exposure. This can trigger the degradation of the MLI materials and induce rapid pressurization of the tank with a high risk of catastrophic failure. In this work, a novel lumped model to simulate the thermal response of MLI-equipped cryogenic liquid hydrogen tanks is presented. The model integrates the accurate database “Coolprop” for hydrogen thermodynamic properties and sub-models for detailed simulation of MLI degradation, providing a realistic simulation of the experimental data obtained under normal operating conditions. The application of the model to several case studies considering different numbers of MLI layers and tank geometries demonstrates that aluminum-based MLI offers scarce protection in case of exposure to a hydrocarbon poolfire. T2 - CISAP 11 CY - Neapel, Italy DA - 15.09.2024 KW - Liquefied hydrogen KW - LNG KW - Fire KW - Insulation KW - MLI PY - 2024 AN - OPUS4-61389 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Harwege, Finn T1 - Characterisation of vacuum insulation panel based cryogenic insulation N2 - Current medium to large scale hydrogen storage tanks utilize a double walled tank with vacuum and a low thermal conductivity powder as bulk fill between the two tank walls. This approach offers poor failure resistance and is not economic to build at a large scale. In NICOLHy an alternative cryogenic insulation concept using vacuum insulation panels (VIP) targeted for tanks with capacities from 40 000 m³ to 100 000 m³ is in research. VIPs consist of a gas tight envelope that surrounds a low conductivity core material. Within the envelope, a vacuum is created, which supresses convective heat transfer. Since the core material is typically very low thermal conductivity, while the envelope material has a relatively high thermal conductivity, thermal bridges where two adjoining panels meet cannot be avoided. Modeling of the thermal behaviour of VIPs exists for the building industry, but not for cryogenic temperatures or applications with multiple layers of VIPs, both of which present a new challenge. Here, these challenges and goals for the thermal modeling within the project are presented, alongside an overview over the project itself. T2 - Themenvorstellung beim BTU Arbeitsgebiet Technische Akustik CY - Cottbus, Germany DA - 23.09.2024 KW - Liquefied Hydrogen PY - 2024 AN - OPUS4-61122 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Renewable energies in Germany – Safety aspects with respect to pipelines N2 - BAM was asked to present German strategies and Projects with respect to Pipelines. Beside an introduction to BAM three Major Topics were presented: Power-to-Gas strategy in Germany, an application of distributed acoustic and fiber optic sensors for the continuous monitoring of pipes and so-called West-Jefferson Tests. T2 - 1st International Cold Regions Oil & Gas Seminar CY - Seoul, Korea DA - 07.12.2016 KW - Pipelines KW - Power-to-gas KW - Distributed acoustic sensors KW - Fiber optics PY - 2016 AN - OPUS4-38708 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Prewitz, Marc T1 - Glaskapillaren für die Wasserstoffhochdruckspeicherung N2 - Wasserstoff spielt eine wichtige Rolle im Bereich der erneuerbaren Energien. Um die hohe gravimetrische Energiedichte auszunutzen, bietet sich die die Hochdruckspeicherung an. Um die theoretische Festigkeit, die geringe Wasserstoffpermeabilität vom Werkstoff „Glas“ und das Wissen von Griffith auszunutzen, sollten Glaskapillaren zum Einsatz kommen. Glas bietet diverse Möglichkeiten solche Kapillaren anzuordnen. Es beginnt bei der Bündelung von Einzelkapillaren und geht bis hin zu ganzen Strukturen. Allerdings stellt sich auch die Frage wie die Berstdruckfestigkeit optimal ausgenutzt und dabei noch die Permeation und das mechanische Langzeitverhalten beachtet werden kann. Ziel dieser Arbeit ist es, die wichtigen Einzelkomponenten diesbezüglich zu untersuchen und einen Langzeitspeicher mithilfe von Simulationen auszulegen. T2 - Fachausschuss I der DGG CY - Würzburg, Germany DA - 09.03.2016 KW - Wasserstoff KW - Hochdruckspeicherung KW - Glaskapillaren PY - 2016 AN - OPUS4-38389 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Trust in Hydrogen Technologies - Safety Issues in the Hydrogen Value Chain N2 - In June 2020, updated in July 2023, the German government presented the National Hydrogen Strategy (NHS), its first strategy for achieving the goals of its hydrogen policy. The NHS sets out a coherent framework for action for the future production, transportation and use of hydrogen and its derivatives, including the corresponding research, innovations and investments. Various measures have been defined to achieve goals such as the decarbonization of various sectors and the market introduction of hydrogen technologies. This will ultimately lead to the introduction of many “new” technologies in many areas of our daily lives, which will only be successful if decision-makers and the public are convinced that these technologies are safe. Therefore, the safety of hydrogen technologies is an important pillar in gaining and maintaining confidence in these new technologies. Safety must keep pace with, or better still, anticipate trends in technological development in order to avoid overly conservative and expensive safety solutions, and at the same time demonstrate the usability and safety of hydrogen. Otherwise, single incidents – not necessarily explosions – can easily lead to uncertainties and therefore to a decrease in trust and acceptance. The presentation will give an overview of how safety issues are addressed in Germany. T2 - Department Seminar - Public Lecture CY - Windhoek, Namibia DA - 12.09.2025 KW - Trustworthiness KW - Hydrogen value chain KW - Safety KW - Public lecture PY - 2025 AN - OPUS4-64438 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -