TY - CONF A1 - Hüllmann, Dino A1 - Kohlhoff, Harald A1 - Neumann, Patrick P. ED - Bársony, I. ED - Zolnai, Z. ED - Battistig, G. T1 - Embedded control of a PMSM servo drive without current measurements N2 - A permanent-magnet synchronous motor (PMSM) servo drive for lightweight robotic platforms that have a high torque demand at low rotational speeds has been developed. First, a current-independent torque controller is derived and cascaded with a speed and position controller, while merely an encoder is used as a sensor device in combination with a speed estimator. Finally, the speed estimator output is compared to gyroscope measurements and the overall functioning is verified on a real system. T2 - 30th Eurosensors Conference - Eurosensors 2016 CY - Budapest, Hungary DA - 04.09.2016 KW - BLDC KW - PMSM KW - Motor control KW - Servo drive KW - Optical incremental encoder PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-388973 DO - https://doi.org/10.1016/j.proeng.2016.11.487 SN - 1877-7058 VL - 168 SP - 1671 EP - 1675 PB - Elsevier B.V. CY - Amsterdam, Netherlands AN - OPUS4-38897 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kuroiwa, T. A1 - Zhu, Y. A1 - Inagaki, K. A1 - Long, S. A1 - Christopher, S. A1 - Puelles, M. A1 - Porinsky, M. A1 - Hatamleh, N. A1 - Murby, J. A1 - Merrick, J. A1 - White, I. A1 - Saxby, D. A1 - Caciano de Sena, R. A1 - Dominguez de Almeida, M. A1 - Vogl, Jochen A1 - Phukphatthanachai, Pranee A1 - Fung, W.-H. A1 - Yau, H.-P. A1 - Okumu, T. O. A1 - Kang'iri, J. N. A1 - Tellez, J. A. S. A1 - Campos, E. Z. A1 - Galvan, E. C. A1 - Kaewkhomdee, N. A1 - Taebunpakul, S. A1 - Thiengmanee, U. A1 - Yafa, C. A1 - Tokman, N. A1 - Tunc, M. A1 - Can, S. Z. T1 - Report of the CCQM-K123: trace elements in biodiesel fuel N2 - The CCQM-K123 key comparison was organized by the Inorganic Analysis Working Group (IAWG) of CCQM to assess and document the capabilities of the national metrology institutes (NMIs) or the designated institutes (DIs) to measure the mass fractions of sodium, calcium, potassium, magnesium phosphorous and sulfur in biodiesel fuel (BDF). The National Metrology Institute of Japan (NMIJ) and National Institute of Standards and Technology (NIST) acted as the coordinating laboratories. Results were submitted by 11 NMIs and DIs. The participants used different measurement methods, though most of them used inductively coupled plasma-mass spectrometry (ICP-MS), isotope dilution technique with ICP-MS and inductively coupled plasma-optical emission spectrometry (ICP-OES) with microwave acid digestion. The material was quite challenging and a number of questions were raised at the IAWG meeting. Concerning S, the variation in S results between participants, particularly those using IDMS methods was discussed at the IAWG meeting. BAM, NIST and NMIJ reviewed their experimental conditions, results and/or uncertainty calculations for IDMS. According to the additional evaluation and investigation, the variances between the revised results became smaller than the original one, the revised results were overlapping between IDMS measurements of S content at the k=2 level. It is not possible to calculate a KCRV with values being modified after submission. It was concluded that this KC does not support S measurements. Accounting for relative expanded uncertainty, comparability of measurement results for each of Na, Ca, K, Mg and P was successfully demonstrated by the participating NMIs or DIs. It is expected that sodium, calcium, potassium, magnesium and phosphorus at mass fractions greater than approximately 0.1 mg/kg, 0.1 mg/kg, 0.05 mg/kg, 0.05 mg/kg and 0.1 mg/kg respectively in biodiesel fuel and similar matrices (fuels and oils etc.) can be determined by each participant using the same technique(s) employed for this key comparison to achieve similar uncertainties mentioned in the present report. Furthermore, the results of this key comparison can be utilized along with the IAWG core capability approach. KW - Biodiesel KW - Fuel KW - Sulphur KW - Reference measurement PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-393941 UR - http://iopscience.iop.org/article/10.1088/0026-1394/54/1A/08008/meta DO - https://doi.org/10.1088/0026-1394/54/1A/08008 SN - 0026-1394 SN - 1681-7575 VL - 54 SP - Tech. Suppl. 2017, 08008, 1 EP - 47 PB - IOP Publishing CY - Bristol, UK AN - OPUS4-39394 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Kanzler, Daniel T1 - Zuverlässigkeitsanalyse von digitalen Radiographie-Systemen bei der Prüfung von realen Materialdefekten N2 - Die zerstörungsfreie Prüfung (ZfP) ist aus solchen Bereichen unseres Lebens nicht mehr wegzudenken, in denen Schäden mit hohen Folgekosten oder Gefährdungen von Menschenleben entstehen können (Beispiele: Transportwesen, Energieerzeugung, Chemieindustrie). In der Praxis kann ein Prüfsystem an seine Grenzen geraten, z.B. bei kleinen Defekten. Defekte mit kritischer Größe werden möglicherweise nicht detektiert. Daher müssen probabilistische Bewertungsverfahren das Prüfsystem beschreiben. Es wird eine objektive Qualitätskennzahl gesucht, auf deren Basis die Anwendbarkeit der Prüfmethode definiert werden soll. Die Auffindwahrscheinlichkeit (engl. probability of detection - POD) erfüllt diese Anforderung. Die POD zeigt auf Basis des Zusammenhangs und der Streuung der Daten, ob das Verfahren für die Prüftätigkeit akzeptiert werden kann oder noch verbessert werden muss. Das ursprüngliche POD-Verfahren wurde für quasi eindimensionale Defekte in dünnen Luftfahrtbauteilen entwickelt. In der industriellen Realität ist diese Bewertung ein Balanceakt zwischen Statistik und Durchführbarkeit: Die Prüfung soll mit realen Defektdaten für die spätere Produktion des Bauteils (bzw. wiederkehrende Wartungsprüfung) bewertet werden. Doch die notwendige Gegenüberstellung zwischen Schliffdaten, für die Erfassung der wahren Defektgröße von räumlich ausgeprägten Defekten und dem Signal eines ZfP-Systems stellt sich als herausfordernde und kostenintensive Aufgabe heraus. Sowohl die Aufstellung eines gemeinsamen Koordiantensystems als auch die Beschreibung und Angleichung der Daten stellen eine notwendige Vorarbeit dar. In dieser Arbeit wird ein mögliches Vorgehen entwickelt, dass im Weiteren eingesetzt werden kann. Während in der Literatur zum Thema POD häufig die Begrenzung des Einsatzes einer eindimensionalen POD (POD mit einem Defektparameter) für reale Defekte bereits erkannt wurde, soll außerdem in dieser Arbeit das Verfahren auf der Signalseite umfassender erweitert werden, um die Einbeziehung realer Defekte in die POD-Bewertung zu ermöglichen. Hierfür werden mit Hilfe dieser Arbeit zwei wesentliche Neuerungen in der POD-Bewertung eingeführt: 1. Die Anzeigenfläche wird als wichtiges Indiz zur Detektion in die Bewertung eingeführt. Dabei zeigt der Ansatz einer Observer-POD, bei dem der Detektierbarkeit eines Defekts beschrieben wird, eine Möglichkeit in die Bewertung zu erweitern. Jedoch wird die notwendige Datenanzahl die für eine Observer-POD selten mit Experimenten erreicht. Daher schlagen wir die Einführung eines Glättungsalgorithmus vor, um auch auf der Basis von wenigen Daten die Flächenabhängigkeit zu erfassen. Der Algorithmus wird hierbei durch simulierte Daten auf seine Funktionsfähigkeit überprüft, bevor er auf reale Defekte angewendet wird. Gleichzeitig helfen die simulierten Daten einen Vergleich zu den vorhergegangenen Ansätzen zu ermöglichen. 2. Darüber hinaus reichen die Daten der realen Defekte häufig nicht aus, um die statistische Forderung zu gewährleisten, so dass es notwendig, wird künstliche Defekte mit einzubeziehen. Deshalb sollen die vorhanden künstlichen Defekte in Form von Referenzdefekten mit einbezogen werden, um die statistische Grundlage zu erhöhen. Für die Prüfung von Referenzdefekten sind jedoch wichtige Einflussgrößen (z.B. Oberflächenrauhigkeit) nicht vorhanden. Wegen der unterschiedlichen Aussagekraft der Daten und zur Vermeidung einer zu optimistischen Abschätzung, ist eine einfache Mischung der Daten ausgeschlossen. Um realen Defekten eine Möglichkeit dafür zu schaffen, dass die Eigenschaften der realen Defekte angemessen auf das Ergebnis der Bewertung des Verfahrens Einfluss nehmen können, wird eine gewichtete Kombination der Defektdaten für die Bewertung vorgestellt. Das Vorgehen wird am Beispiel der radiographischen Prüfung einer elektronenstrahlgeschweißten Naht durchgeführt. Die Schweißnaht verbindet den Deckel zur Außenwand eines Kupferbehältern, der für die spätere Endlagerung von verbrauchten Brennstäben aus Kernkraftwerken entwickelt wurde. Die Messergebnisse stammen aus von der Firma Posiva Oy, dem zuständigen Unternehmen für die Endlagerung von verbrauchten Brennstäben aus Kernkraftwerken in Finnland. Hierbei stellt die POD-Bewertung ein wichtiges Element in der Gesamtrisikobewertung für das Endlagersystem dar. T3 - BAM Dissertationsreihe - 153 KW - Radiographie KW - POD KW - Zuverlässigkeit KW - Zerstörungsfreie Prüfung (ZfP) KW - Probabilistische Bewertung PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-388723 SN - 978-3-9818270-1-9 SN - 1613-4249 VL - 153 SP - iii EP - 134 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-38872 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kinne, Marko A1 - Thöns, Sebastian T1 - Fatigue Reliability Based on Predicted Posterior Stress Ranges Determined from Strain Measurements of Wind Turbine Support Structures N2 - In the present paper, an approach for updating the continuous stress range distribution of a welded connection of a wind turbine support structure with predicted information from strain measurements is presented. Environmental conditions, such as wind or, in offshore fields, waves and currents, in combination with rotor excitations generate cyclic stresses affecting the reliability of welded joints of the support structure over the service life. Using strain measurements, these conditions can be monitored, and the resulting stress ranges, under consideration of measurement, mechanical and material uncertainties, can be reconstructed. These stress ranges can be used as an input for updating the prior probability density function (PDF) of the stress ranges predicted by the overall dynamics and a detailed design analysis. Applying Bayesian probability theory and decision theoretical implications, the predicted posterior probability density of the stress ranges is calculated based on the design information and uncertainties. This approach is exemplified, and it is shown how the predicted stress ranges and the design stress ranges are distributed. The prior and the predicted posterior stress ranges are used for a reliability calculation for potentially entering a pre-posterior decision analysis KW - Strain measurements of wind turbine support structures KW - Bayesian updating of stress ranges KW - Posterior fatigue reliability PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-572663 DO - https://doi.org/10.3390/en16052225 VL - 16 IS - 5 SP - 1 EP - 26 PB - MDPI AN - OPUS4-57266 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kinne, Marko A1 - Farhan, Muhammad A1 - Schneider, Ronald A1 - Thöns, Sebastian T1 - Influence of the structural integrity management on the levelized cost of energy of offshore wind: a parametric sensitivity analysis N2 - The levelized cost of energy (LCoE) is an important measure to quantify the macro-economic efficiency of an offshore wind farm and to enable a quantitative comparison with other types of energy production. The costs of the structural integrity management - which is required to ensure an adequate lifetime reliability of the turbine support structures - are part of the operational expenditures of an offshore wind farm. An optimization of the structural integrity management may reduce the operational expenditures and consequently the LCoE. However, the effect of the structural integrity management on the LCoE is hardly known. To investigate this effect, this paper presents a sensitivity analysis of the LCoE of a generic offshore wind farm. The probabilistic models of the parameters influencing the LCoE are based on a literature study including an explicit model for the structural integrity management. The analysis reveals that LCoE may potentially be reduced if an optimization of the structural integrity management enables a service life extension. T2 - International Probabilistic Workshop 2022 CY - Stellenbosch, South Africa DA - 08.09.2022 KW - Structural integrity management KW - Levelized cost of energy KW - Sensitivity analysis PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-572724 DO - https://doi.org/10.14311/APP.2022.36.0090 VL - 36 SP - 90 EP - 98 PB - Acta Polytechnica CTU Proceedings AN - OPUS4-57272 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sauermoser-Yri, M. A1 - Veldurthi, N. A1 - Wölfle, C. H. A1 - Svartvatn, P. J. A1 - Flo Hoem, S. O. A1 - Lid, M. J. A1 - Bock, Robert A1 - Palko, J. A1 - Torgersen, J. T1 - On the porosity-dependent permeability and conductivity of triply periodic minimal surface based porous media N2 - With the fast development in the field of additive manufacturing, triply periodic minimal surface (TPMS) based porous media have recently found many uses in mechanical property tuning. However, there is still a lack of understanding in their porosity-dependent permeability and electrical as well as thermal conductivity. Here, we perform finite volume simulations on the solid and void domains of the Schoen gyroid (SG), Schwarz primitive (SP) and Schwarz primitive beam (SPB) TPMS with porosities between 63% and 88% in Ansys Fluent. A simple cubic lattice (CL) of equivalent porosity served as reference. The SPB and CL showed up to one order of magnitude higher permeabilities than the SG and SP. However, SG and SP have about 1.3 and 2.6 times the electrical and thermal conductivity of SPB and CL, respectively. Furthermore, the properties of SPB and CL are largely affected by the surface area density, whereas tortuosity variation does not impact permeability and conductivity to a major extent. Finally, empirical relations are adapted to describe the presented data and thus, they may enable future designers of TPMS based porous structures to fine-tune the geometries according to the requirements on permeability and electrical as well as thermal conductivity. KW - Metals and Alloys KW - Surfaces, Coatings and Films KW - Biomaterials KW - Ceramics and Composites PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-585250 DO - https://doi.org/10.1016/j.jmrt.2023.09.242 SN - 2238-7854 VL - 27 SP - 585 EP - 599 PB - Elsevier B.V. AN - OPUS4-58525 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bock, Robert A1 - Mair, Georg W. A1 - Tiebe, Carlo A1 - Melzer, Michael A1 - Klaus, Christian A1 - Nattuveettil, Keerthana A1 - Engel, Thomas A1 - Prager, Jens T1 - Eine digitale QI für technische Anlagen: Beispiel Wasserstofftankstelle (H2) N2 - Mit der Initiative QI-Digital werden völlig neue Perspektiven für das Sicherheitsmanagement und die Qualitätssicherung technischer Anlagen erschaffen. Unsere Forschung im Kontext einer Wasserstofftankstelle zeigt, wie digitale Innovationen und Verfahren die Herausforderungen effizienter und verlässlicher Qualitätssicherung für komplexe Anlagen bewältigen können. In diesem Vortrag werden Potentiale und Beispiele der digitalen QI für technische Anlagen demonstriert und diskutiert: Moderne Anlagenüberwachung mit digitalen Zwillingen und KI sowie Kalibriermanagement mithilfe digitaler Kalibrierscheine und elektronischem Siegel. T2 - 2. QI Digital Forum CY - Berlin, Germany DA - 10.10.2023 KW - Wasserstoff KW - Sensorik KW - Qualitätsinfrastruktur KW - Digitalisierung KW - Druckspeicher KW - Verwaltungsschale PY - 2023 AN - OPUS4-58599 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bock, Robert T1 - Pilotprojekt Wasserstofftankstelle - Session 2: Verlässliche Wassertofftankstellen N2 - Was ist QI? Qualitätsinfrastruktur – Das Zusammenwirken von nationalen Institutionen im Bereich der Metrologie, Normung und Standardisierung, Akkreditierung, Konformitätsbewertung und Marktüberwachung, mit dem Ziel die Qualitätssicherung bei Produkten und Prozessen in Deutschland zu gewährleisten. Unser Ziel ist es, unsere bewährte Qualitätsinfrastruktur (QI) noch besser zu machen und so einen Beitrag zur Lösung von sozioökonomischen, ökologischen und technologischen Herausforderungen unserer Zeit zu leisten. Eine der bedeutendsten technologischen Herausforderungen unserer Zeit ist die Digitalisierung. Die zentralen Akteure der deutschen QI wollen diese digitalisieren. Beteiligte Institutionen sind aktuell BAM (Konformitätsbewertungen in bestimmten Bereichen), DAKKS (Akkreditierung), DIN/DKE (Normung), PTB (Metrologie). Wir wollen also ein Reallabor errichten, das die Wertschöpfungskette einer Tankstelle abbildet, also eine Wasserstofftankstelle beinhaltet, die dann mit erweiterter Sensorik ausgestattet werden soll. Somit sollen digitale Prozesse abgebildet werden können sowie sensorgestützte Verfahren zur qualitätsgesicherten Datenerfassung und -auswertung genutzt werden. Diese gesammelten Daten sollen dann in eine Dateninfrastruktur eingehen und mithilfe eines Datenmanagementsystems sowie künstlicher Intelligenz in einem Digitalen Zwilling zusammenlaufen, der die digitale Prozessüberwachung der Sicherheit möglich macht. Schließlich sollen die in QI Digital entwickelten digitalen Strukturelemente der QI erprobt werden, insbesondere die QI Cloud, Smart Standards und digitalen Zertifikate. Im Zusammenspiel ermöglicht das unter anderem die Entwicklung von Predictive Maintenance Verfahren für: 1. die Optimierung von Wartungszyklen und Minimierung von Ausfallzeiten Erhöhung der Betriebssicherheit durch frühzeitige Identifikation kritischer Zustände im Gesamtsystem 2. Entwicklung verlässlicher Qualitäts- und Sicherheitsstandards  3. Digital-gestützte Risikobeurteilung und Konformitätsbewertung Die im Pilotprojekte betrachteten Sicherheitsaspekte sind also zusammenfassbar als: a) Auswirkungsbetrachtungen bei möglichen Fehlfunktionen oder Defekten b) Die genannte vorrauschauende Instandhaltung und damit verbundene Lebensdauerprognose, die in Kombination eine bessere allgemeine Verfügbarkeit garantieren sollen Als Grundlage hierfür benötigen wir aber Änderungen im Bereich der technischen Regeln und Normen, um die neuen digitalen Werkzeuge zuzulassen und nutzbar zu machen. T2 - QI Forum 2022 CY - Berlin, Germany DA - 11.10.2022 KW - Wasserstoff KW - Qualitätsinfrastruktur KW - Digitalisierung PY - 2022 AN - OPUS4-61356 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Orellana Pérez, Teresa T1 - QI Digital Use Case Hydrogen Refueling Station N2 - BAM is part of the “Quality Infrastructure Digital” (QI Digital) initiative of the German Federal Ministry for Economic Affairs and Climate Action (BMWK). This initiative aims at coordinating a large cooperation project, “QI Digital” for making German and European quality management systems fit for the digital transformation. It is a fact that the digitization of new products and services is occurring much faster than quality management systems can be accordingly updated. Thus, the digital transformation of quality management is necessary to preserve the competitiveness of the German and European industries that stand for quality and safety in the global market. The Use Case “Reliable Hydrogen Refueling Station” of QI Digital aims at creating new solutions that are transferable to other technical systems and at further developing standards and technical rules as a contribution to technology transfer and innovation. T2 - 4th German-Korean Hydrogen Conference CY - Seoul, Republic of Korea DA - 31.10.2023 KW - Hydrogen refueling station KW - Digital quality infrastructure PY - 2023 AN - OPUS4-59303 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bock, Robert A1 - Mair, Georg W. T1 - Pilotprojekt "Verlässliche Wasserstofftechnologie" - Beispielanwendung für eine technische Anlage N2 - Kurzvorstellung des Pilotprojektes Verlässliche Wasserstofftechnologie in QI Digital. Anwendung der QI Digital Werkzeuge an einer technischen Anlage beispielhaft gezeigt anhand von sechs im Projekt entwickelten Demonstratoren. Unser erklärtes Ziel ist die Unterstützung des Markthochlaufs von Wasserstofftechnologien durch Digitalisierung der QI. Bei der Qualitätsinfrastruktur von technischen Anlagen geht es vor allem die Themen QI Dokumentation und Zugänglichkeit, Verfügbarkeit der Anlage und Informationen darüber, sowie Inspektionszyklen mit zeitaufwändigen und teuren manuellen Prüfungen. Mit dem Übergang zu einer digitalen QI streben wir hier an, eine kontinuierliche Überwachung des momentanen Gesundheitszustandes der Anlage und automatisierter Dokumentation hierüber, die fälschungssicher und vertraulich zugänglich gemacht werden kann, zu erreichen. Hierzu sollen die im Gesamtprojekt entwickelten QI Digital Werkzeuge zum Einsatz kommen. T2 - QI Forum 2024 CY - Berlin, Germany DA - 09.10.2024 KW - Wasserstoff KW - Qualitätsinfrastruktur KW - Digitalisierung PY - 2024 AN - OPUS4-61354 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kehr, Torsten T1 - Project QI-Digital - Quo vadis Use Case H2 Refueling Station? N2 - As a part of the QI-Digital cooperation project, BAM is setting up a hydrogen refuelling station research platform at the Test site for Technical Safety in Horstwalde. Based on this platform, BAM intends to develop, to test and to optimize new measurement techniques as well as data acquisition and processing methods for hydrogen refuelling stations and their periphery in close cooperation with partners from the quality infrastructure and industry. The presentation will introduce the hydrogen refuelling station use case and provide insights into the issues and research goals of the associated subprojects. T2 - H2-Colloquium of the Competence Centre „H2SAFETY@BAM” CY - Online meeting DA - 16.02.2022 KW - Hydrogen KW - Safety KW - QI-Digital PY - 2022 AN - OPUS4-54361 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Aspekte einer digitalen Lebenslaufakte (Impulsvortrag) N2 - Durch Einsatz neuer Technologien im Transport von komprimiertem Wasserstoff konnte eine Verdreifachung des Nutzlastverhältnisses erreicht werden. Diese neuen Speicher auf den Transportfahrzeugen müssten aber anders auf ihre Sicherheit überprüft werden, als dies heute gefordert wird. Mit dem Markthochlauf Wasserstoff vervielfacht sich zudem die Anzahl der Transporteinheiten. Da sich im Zuge der neuen H2-Transportfahrzeuge aber auch die Anzahl der einzelnen Speicher pro Fahrzeug etwa verzwanzigfacht hat, kommen die Kapazitäten für die erforderliche wiederkehrende Prüfung an ihre Grenzen. Dies könnte evtl. durch eine entsprechende Erhöhung der Prüfkapazitäten gelöst werden. Da dies aber weder praktisch machbar ist noch technisch wirklich sinnvoll, müssen alternative Ansätze z.B. durch digital erfasste zerstörungsfreie Prüfkonzepte gesucht werden. Hierzu bedarf es aber einer Lebenslaufakte, die beginnend von der Definition einer Bauweise über die Baumusterprüfung, Zulassung, Herstellung, erstmalige Prüfung, Verwendung und wiederkehrenden oder begleitenden Prüfungen bis zum Verschrotten alle Daten erfassen und verwalten kann. Eine solche Lebenslaufakte könnte auch als eine Art digitaler Produktpass (DPP) verstanden werden. T2 - QI-digital Forum 2023 CY - Berlin, Germany DA - 10.10.2023 KW - Wasserstoffspeicher KW - Lebenslaufakte KW - Digitaler Produktpass DPP KW - Wiederkehrende Prüfung KW - Lebensdauerüberwachung PY - 2023 AN - OPUS4-58559 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo T1 - Error prevention, damage prevention, and safety management in hydrogen technologies N2 - This tutorial presents requirements and properties of sensor systems and shows application examples of these technologies for safety and process control for hydrogen technologies. Sensor systems are widely used in hydrogen technologies. The focus is on gas sensors as well as sensors for pressure, temperature, and gas flow. These systems are applied, among other things, for monitoring and control of operating conditions, indication of hazardous conditions and triggering of alarms. To integrate the error avoidance and loss prevention strategy into hydrogen technologies. This includes the implementation of preventive measures as elements of safety management to identify and eliminate potential sources of error. In addition, training should be specifically focused on avoiding errors and the safe use of hydrogen technologies. A well-thought-out strategy for error prevention makes a significant contribution to preventing accidents and increasing overall safety when using hydrogen. T2 - Sensor and Measurement Science International (SMSI) CY - Nuremberg, Germany DA - 06.05.2025 KW - Hydrogen KW - Safety Management KW - Gas Sensors KW - Performance Testing PY - 2025 AN - OPUS4-63280 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Flege, J. I. T1 - BTU-BAM Graduate School “Trustworthy Hydrogen” N2 - Beim Online-Meeting des Wasserstoffnetzwerks Lausitz mit dem Titel "Wirtschaft trifft Wissenschaft und Forschung" wurde die BTU-BAM-Graduiertenschule Trustworthy Hydrogen vorgestellt. Es handelt sich um die erste Graduiertenschule in Deutschland, die sich mit der Vertrauenswürdigkeit von Wasserstoff beschäftigt und die einzigartigen Kompetenzen von BAM und BTU zur Ausbildung der nächsten Generation von interdisziplinären Wasserstoff-Wissenschaftlern bündelt. N2 - The BTU-BAM graduate school Trustworthy Hydrogen was presented at the online meeting of the Lausitz Hydrogen Network entitled "Business meets Science and Research". It is the first graduate school in Germany to focus on the trustworthiness of hydrogen and combines the unique competencies of BAM and BTU to train the next generation of interdisciplinary hydrogen scientists. T2 - Lausitzer Netzwerktreffen DurcH2atmen "Wirtschaft trifft Wissenschaft und Forschung" " CY - Online meeting DA - 22.11.2022 KW - H2Safety@BAM KW - Graduate School KW - Trustworthy Hydrogen KW - Graduiertenkolleg PY - 2022 AN - OPUS4-56443 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Competence Centre H2Safety@BAM N2 - Deutschland hat mit verschiedenen Ländern Energiepartnerschaften geschlossen, darunter auch mit Japan. Im Rahmen des 3. Treffens der Wasserstoff-Arbeitsgruppe wurde das strategische Vorgehen beider Länder zu Entwicklungen von Wasserstoffrichtlinien, Zertifizierung und Sicherheit vorgestellt und diskutiert. Die BAM hat in einem Vortrag wichtige Themen aus dem Bereich der Sicherheitsforschung sowie zu sicherheitstechnischen Fragestellungen über die Wertschöpfungskette vorgestellt. Außerdem wurde das Arbeitsprogramm und ausgewählte Projekte des Kompetenzzentrums H2Safety@BAM vorgestellt. N2 - Germany has concluded energy partnerships with various countries, including Japan. During the 3rd meeting of the Hydrogen Working Group, the strategic approach of both countries on developments of hydrogen guidelines, certification and safety was presented and discussed. BAM gave a presentation on important topics in the field of safety research and on safety-related issues along the value chain. Furthermore, the work program and selected projects of the competence center H2Safety@BAM were presented. T2 - 3rd Meeting of the Hydrogen Working Group - Japanese-German Energy Partnership CY - Berlin, Germany DA - 27.02.2023 KW - Hydrogen KW - Japanese-German energy partnership KW - Safety KW - H2Safety@BAM PY - 2023 AN - OPUS4-57126 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Offene Fragestellungen bei der Sicherheit von H2-Anwendungen aus Sicht der BAM N2 - Um die Energiewende voranzubringen, wird neben dem Ausbau der Erneuerbaren Energien ein schneller Markthochlauf bei Wasserstoff-Erzeugung, Transport und Anwendung angestrebt. Dieser Markthochlauf geht derzeit insbesondere einher mit Fragen der Wirtschaftlichkeit und der Umsetzung einer Serienfertigung von Elektrolyseuren. Bei Fragen der Sicherheit wird üblicherweise auf das bestehende Regelwerk verwiesen. Da der Umgang mit Wasserstoff und die Technologien zur Wasserstoff- Erzeugung nicht neu sind, geht man davon aus, dass durch die Einhaltung der bestehenden Regelwerke die Anlagen ausreichend sicher sind. Aber ist das wirklich so? Decken die bestehenden technischen Regelwerke alle derzeitigen Entwicklungen im Zusammenhang mit der Wasserstofferzeugung und -nutzung in allen notwendigen Facetten ab, um die Sicherheit zu gewährleisten? Der Experten-Workshop soll die Möglichkeit bieten, sich über die Sicherheit bei Wasserstofferzeugung und -nutzung auszutauschen sowie offene Fragestellungen und Lücken im Regelwerk zu identifizieren. Hierzu sind sowohl Impulsvorträge als auch ein offener Austausch mit allen Teilnehmenden geplant. T2 - GRS-Online-Workshop Wasserstoffsicherheit CY - Online meeting DA - 06.07.2023 KW - H2Safety@BAM KW - Wasserstoffsicherheit KW - Regelwerke PY - 2023 AN - OPUS4-57908 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Forschungsnetzwerk Wasserstoff N2 - Die BAM beteiligt sich sehr aktiv am Forschungsnetzwerk Wasserstoff, eines von neun Forschungsnetzwerken Energie der Bundesregierung. Der Vortragende ist Sprecher des Cluster IV "Sicherheit, Akzeptanz und nachhaltige Markteinführung" vom Forschungsnetzwerk und wurde vom Geschäftsführer des Center of Safety Excellence GmbH gebeten, die aktuellen Forschungsbedarfe des Netzwerkes, die in der Expertenempfehlung 2023 dem BMWK übermittelt wurden, vorzustellen. T2 - Beiratssitzung des Center of Safety Excellence GmbH CY - Online meeting DA - 20.04.2023 KW - H2Safety@BAM KW - Forschungsnetzwerk Wasserstoff KW - Forschungsbedarfe KW - Sicherheit PY - 2023 AN - OPUS4-57373 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hörmann, Anja Franziska T1 - (Grazing Incidence) Small-angle X-ray Scattering for STOP N2 - We remind project partners of the principles of SAXS, GISAXS and X-ray reflectivity and their applicability to the antimicrobial particles and coatings developed within the STOP project. T2 - M25 project meeting: Surface Transfer of Pathogens (STOP) CY - Bucharest, Romania DA - 19.09.2024 KW - X-ray Scattering KW - Nanomaterial PY - 2024 AN - OPUS4-62774 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Hydrogen - Safety of Energy Carriers N2 - Eine sichere Versorgung mit Energie stellt für moderne Industriegesellschaften eine elementare Grundvoraussetzung dar. Inwieweit in Deutschland die Energiewende im Sinne von zum Beispiel Energiepolitik, Förderung aber auch gesellschaftlicher Entwicklung gestaltet wird, wurde im Rahmen der 12. Wildauer Wissenschaftswoche diskutiert. Die BAM hat einen Beitrag zum Thema Sicherheit von Energieträgern beigetragen und das Kompetenzzentrum H2Safety@BAM vorgestellt. N2 - A safe supply of energy is a fundamental prerequisite for modern industrial societies. The extent to which the energy turnaround is being shaped in Germany in terms of, for example, energy policy, promotion, but also social development was discussed during the 12th Wildau Science Week. BAM contributed to the topic of safety of energy sources and presented the competence center H2Safety@BAM. T2 - 12. Wildauer Wissenschaftswoche CY - Wildau, Germany DA - 27.02.2023 KW - Hydrogen KW - Safety KW - H2Safety@BAM PY - 2023 AN - OPUS4-57125 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Holtappels, Kai T1 - Impulse zum Hochlauf einer Wasserstoffwirtschaft in Deutschland N2 - Wasserstoff als sauberer, vielseitig einsetzbarer Energieträger spielt bei der dringend benötigten Energiewende eine entscheidende Rolle. Die Etablierung einer Wasserstoffwirtschaft wird tiefgreifende Auswirkungen auf verschiedene Sektoren der deutschen Wirtschaft haben und diese grundlegend transformieren. Die vorliegende Publikation fokussiert Herausforderungen und Maßnahmen für den Hochlauf einer Wasserstoffwirtschaft in Deutschland und ist in einem knapp einjährigen Multi-Stakeholder-Dialog gemeinsam mit führenden Expertinnen und Experten aus Industrie, Wissenschaft, Gesellschaft (NGOs) sowie Vertretern aus der Politik-entstanden. KW - Wasserstoff KW - Markthochlauf KW - Zukunftsdialog KW - Herausforderungen PY - 2025 SN - 978-3-911670-07-4 SP - 1 EP - 62 PB - VDI Verein Deutscher Ingenieure e.V. CY - Düsseldorf AN - OPUS4-63941 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Eberwein, Robert T1 - Untersuchung der Gefährdung von Personen und Bauwerken in Folge des Versagens von LNG-Kraftstoffspeichern für Fahrzeuge in Tunneln N2 - Liquefied Natural Gas (LNG) aus regenerativen Quellen, stellt einen potenziellen Kraftstoff für den Schwer- und Fernverkehr des Straßenverkehrs dar. Gegenüber seinen positiven Eigenschaften zu dem in diesem Verkehrssektor häufig verwendeten Kraftstoff Diesel birgt der Kraftstoff aber auch Gefahren für Personen und Bauwerke durch seine sehr niedrige Temperatur bei der Speicherung von ca. -160 °C und seine Explosionsfähigkeit in der Gas-Phase. In der Arbeit wurde sich mit der Gefährdung von Personen und Bauwerken hinsichtlich der von LNG ausgehenden Gefahren in Tunneln auseinandergesetzt. Tunnel stellen besonders schützenswerte Bauwerke dar, da aus vorhergehenden Störfällen in Tunneln bekannt ist, dass diese mit hohen Personen-, Bauwerks-, und Volkswirtschaftlichen-Schäden einhergehen können. Untersuchungsschwerpunkt bei der Bewertung von Gefährdungen durch LNG stellte eine Ereigniskaskade bestehend aus Freisetzung, Verdampfung, Stoffausbreitung und Zündung des sich gebildeten explosionsfähigen LNG-Gas/Luft-Gemisches dar. Mit dem Ziel eine solche Ereigniskaskade realitätsnah vorhersagen und zukünftig hierzu Risikoanalysen durchführen zu können wurden innerhalb der Arbeit Parameterstudien sowie Kalibrierungen und Validierungen gegenüber experimentellen Untersuchungen durchgeführt. Mit den Modellen wurden in der Arbeit exemplarische Fallbeispiele zu Störfällen untersucht. Ergebnisse dieser waren, dass Gefährdungen insbesondere von flüssigem LNG nach dessen Freisetzung und der Verbrennung von LNG-Gas/Luft-Gemischen ausgingen. N2 - Liquefied Natural Gas (LNG) from regenerative sources is a potential fuel for heavy and long-distance road traffic. In contrast to its positive properties compared to diesel, which is often used in this transport sector, the fuel also contains hazards from its very low storage temperature of approx. -160 °C and its explosiveness in the gas phase for personal and structural safety. The dissertation dealt with the dangers to persons and infrastructures according to the hazards by LNG in tunnels. Tunnels are especiallyworth protecting structures since it is known from previous incidents in tunnels that they can go hand in hand with high damage to the people, the structure, and the economy. The main focus of the investigation into the assessment of hazards from LNG was an event cascade consisting of release, evaporation, dispersion, and ignition of the explosive LNG-vapor/air-mixture formed. To realistically predict such an event cascade and being able to carry out risk analyzes for this purpose in the future, parameter studies such as calibrations and validations were carried out concerning experimental investigations. Exemplary case studies on incidents were examined in the thesis with the validated models. The results of this were that there were especially hazards in particular from liquid LNG after its release and the combustion of LNG-vapor/air-mixtures. KW - Verflüssigtes Erdgas KW - Erneuerbare Energien KW - Numerische Strömungsmechanik KW - Sicherheitstechnik KW - Liquefied Natural Gas KW - LNG KW - Renewable fuels KW - CFD KW - Safety engineering PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-521145 DO - https://doi.org/10.14279/depositonce-11346 SP - 1 EP - 240 PB - TU Berlin CY - Berlin AN - OPUS4-52114 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hajhariri, Aliasghar A1 - Eberwein, Robert A1 - Perrone, Luca Pakj A1 - Cozzani, Valerio A1 - Otremba, Frank A1 - Seidlitz, Holger T1 - Study the impact of spacer at thermal degradation process of MLI-based insulation in fire condition N2 - To reduce CO2 emissions, energy carriers such as hydrogen are considered to be a solution. Consumption of hydrogen as a fuel meets several limitations such as its low volumetric energy density in gas phase. To tackle this problem, storage as well as transportation in liquified phase is recommended. To be able to handle this component in liquid phase, an efficient thermal insulation e.g., MLI insulation is required. Different studies have been addressed the vulnerability of such insulation against high thermal loads e.g., in an accident engaging fire. Some of research works have highlighted the importance of considering the MLI thermal degradation focusing on its reflective layer. However, limited number of studies addressed the thermal degradation of spacer material and its effect on the overall heat flux. In this study, through systematic experimental measurements, the effect of thermal loads on glass fleece, glass paper as well as polyester spacers are investigated. The results are reported in various temperature and heat flux profiles. Interpreting the temperature profiles revealed that, as the number of spacers in the medium increases, the peak temperature detectable by the temperature sensor on the measurement plate decreases. Each individual spacer contributes to mitigating the radiative energy received by the measurement plate. Stacks of 20–50 spacers (this is the number of layers in commercial MLI systems applied for liquid hydrogen applications) can potentially reduce the thermal radiation by 1–2 orders of magnitude. An empirical correlation to predict a heat flux attenuation factor is proposed, which is useful for further numerical and analytical studies in the temperature range from ambient to 300 ◦C. KW - Cryogenic KW - Liquid Hydrogen KW - Multi-Layer Insultation KW - Heat Transfer KW - Hydrogen Storage Safety PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-614919 DO - https://doi.org/10.1016/j.jlp.2024.105461 SN - 0950-4230 VL - 92 SP - 1 EP - 7 PB - Elsevier Ltd. AN - OPUS4-61491 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tschirschwitz, Rico T1 - Sicherheitstechnische Fragestellungen bei statioären EES - Istzustand und zukünftige Entwicklung/Projekte N2 - Der Vortrag stellt potentielle sicherheitstechnische Fragestellungen beim weiterten Ausbau der stationären elektrischen Energiespeicher (EES) in Deutschland dar. Darüber hinaus werden aktuelle Aktivitäten und Projekte der BAM mit Bezug zur Sicherheit von Lithiumbatterien und stationären elektrischen Energiespeichern vorstellt. T2 - Fachgespräch „Stationäre elektr. Energiespeicher (EES) und Anlagensicherheit“ CY - Online meeting DA - 29.01.2021 KW - Stationäre Energiespeicher KW - Elektrische Energiespeicher KW - EES KW - Auswirkungsbetrachtungen PY - 2021 AN - OPUS4-52116 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Risk management and consequence control in hydrogen transport - volume dependent pressure limitation as a scientific approach for consequence control N2 - With technological development, the transport units for compressed gases are becoming larger and their number is increasing. Simultaneously, the filling pressure for hydrogen in transport has increased far beyond the 200 bar, which has been the common European standard for decades. In total, this increases the potential consequences of an incident, which needs to get limited for ensuring acceptance in current practice with pressure vessels from large serial production. Consequently, the measures for new developments of extremely large and highly pressurised pressure vessels should meet a risk based higher level of requirements. For this purpose, the so-called pressure-volume product was proposed as a safety related criteria to the relevant regulatory bodies in 2020. The approach was accepted, and a working group was set up at the United Nations for developing a broadly accepted limitation of today's established pressure vessels compared to future units with even more gas content. The path to the finally decided limit value of 1.5 million bar litres is presented here for hydrogen with its individual steps: ‘Boundary between major accident and disaster’, ‘The effect of pressure waves on the human body’, ‘The propagation of pressure waves’, ‘The reference value for population density’ and ‘Impact of pressure waves’. This result of the UN working group has been accepted in December 2023 and will lead to a binding limitation of the pressure volume product for the so called pressure receptacles by 2027. The work on units larger than this pV-limit is going on at ISO level. T2 - 11th International Conference on Hydrogen Safety ICHS 2025 CY - Seoul, South Korea DA - 22.09.2025 KW - Safety KW - Hydrogen transport KW - Major accident KW - Pressure wave KW - Population density KW - Science with impact PY - 2025 AN - OPUS4-64198 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kröll, Mirco T1 - Harmonising Tribotests of Polymers in Hydrogen N2 - This talk harmonised methods to investigate friction and wear of commercial and experimental polymer compounds in hydrogen using several tribometers. T2 - Surface Ventures - Symposium on Hydrogen Tribology CY - Online meeting DA - 31.07.2025 KW - Hydrogen KW - Polymers KW - Tribometer KW - Wear KW - Coefficient of Friction KW - Interlaboratory comparison KW - Comparability KW - Harmonisation KW - Standardisation KW - Tribology KW - Oil-coupled compounds KW - FAIR data KW - Database KW - i-TRIBOMAT PY - 2025 AN - OPUS4-63838 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Camplese, Davide T1 - Safety assessment of MLI super-insulation systems for cryogenic liquid-hydrogen tanks in fire scenarios N2 - In the context of green energy transition, cryogenic tanks featuring MLI systems are emerging as a leading solution to store hydrogen in heavy-duty vehicles. However, the integrity of such tanks can be jeopardized by fire. In such a scenario, MLI materials degradation can occur, leaving the tank unprotected from the fire heat flux, with consequent rapid pressurization and a high risk of failure. This study presents an assessment of aluminum-based MLI for liquid hydrogen cryogenic tanks under fire exposure based on the estimation of the time to mechanical failure of the equipment. This is calculated through an innovative model that simulates the thermomechanical response of the tank, including the MLI thermal degradation and the pressure-relief valve (PRV) operation. The application to several case studies that consider a typical LH2 tank featuring a wide range of MLI configurations demonstrated the likelihood of failure in case of exposure to a hydrocarbon pool fire, providing also comprehensive insights into the impact of the insulation characteristics and operating conditions on the time to failure. T2 - 18th EFCE International Symposium on Loss Prevention and Safety Promotion in the Process Industries CY - Bologna, Italy DA - 08.06.2025 KW - LH2 KW - Insulation KW - Tanks KW - Fire KW - LNG PY - 2025 AN - OPUS4-63427 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Overview of Hydrogen Safety and remaining challenges N2 - Die Konrad-Adenauer-Stiftung und die Delegation der Deutschen Wirtschaft in Nigeria führt eine "Nigeria Hydrogen Future Webinar Series" durch. Die vierte Veranstaltung wurde unter dem Titel "Safe and Sustainable Hydrogen Production in Nigeria" durchgeführt. Die BAM bzw. das Kompetenzzentrum H2Safety@BAM wurde eingeladen, einen Übersichtsvortrag zur Wasserstoffsicherheit und zukünftigen Herausforderungen mit Blick auf sicherheitstechnische Fragestellungen zu halten. Der Vortrag bildete neben zwei weiteren Vorträgen der Kern des Webinbars. N2 - The Konrad Adenauer Foundation and the Delegation of German Business in Nigeria is conducting a "Nigeria Hydrogen Future Webinar Series". The fourth event was held under the title "Safe and Sustainable Hydrogen Production in Nigeria". BAM respectively the Competence Centre H2Safety@BAM was invited to present an overview lecture on hydrogen safety and future challenges with regard to safety-related issues. The lecture formed the core of the webinbar along with two other presentations. T2 - 4th Nigeria Hydrogen Future Webinar Series CY - Online meeting DA - 27.07.2022 KW - H2Safety@BAM KW - Safety challenges KW - Hydrogen safety PY - 2022 AN - OPUS4-55393 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nattuveettil, Keerthana A1 - Brunner, Nanine A1 - Tiebe, Carlo A1 - Melzer, Michael A1 - Johann, Sergej A1 - Neumann, Patrick P. A1 - Bartholmai, Matthias T1 - Einsatz von Sensortechnologien an einer Wasserstofftankstelle als Beitrag zur digitalen Qualitätsinfrastruktur T1 - Use of sensor technologies at hydrogen test platform as a part of QI Digital N2 - Die Optimierung und Validierung des digitalen Wasserstofftankstellenmanagements mit Sensortechnologien ist das übergeordnete Ziel des Teilprojekts Digitale Qualitätsinfrastruktur mit Sensortechnologien (QIST) am Use Case H2, im Rahmen der digitalen Qualitätsinfrastruktur (QI digital[1]). Hierfür sollen u.a. Sensornetzwerke mit digital-gestützten Auswertungsstrategien intelligent gestaltet werden (Stichwort KI bzw. digitaler Zwilling). Verschiedene, sich ergänzende Sensoren, Systemkomponenten und KI-Methoden stehen als Bausteine intelligenter Sensorsysteme zur Verfügung, mit dem Zweck, die physikalischen und chemischen Parameter an und in Anlagen umfassend und effizient zu überwachen sowie Fehlfunktionen zuverlässig zu detektieren und zu interpretieren, Abbildung 1. Konkrete Arbeitsschritte sind, nach dem Aufbau der Versuchsplattform „Wasserstofftankstelle“, die Instrumentierung von Sensorik und deren digitale Integration in das Tankstellenmanagementsystem sowie die Validierung im Realbetrieb. Die somit erzielten Messergebisse sowie die Messunsicherheiten, Historien und Verfahren werden in digitaler Form aufbereitet, gespeichert und fortlaufend in die KI-basierte Datenauswertung einbezogen, inkl. der Anbindung an die metrologische Rückführungskette. Ziele sind: • Einführung eines neuen messtechnischen Ansatzes und eines digitalen Zwillings für den Anwendungsfall "Wasserstofftankstelle" auf Basis der H2-Sensorik sowie der Zustandsgrößen Druck und Temperatur • Qualitätssicherung durch Applikationen zuverlässiger Gassensorik, Manometer und Thermometer sowie KI-Methoden zur Prozesskontrolle und Detektion von Fehlfunktionen • Nutzung von digitalen Kalibrierscheinen (DCCs) insbesondere für die Messgröße Temperatur zur Realisierung der metrologischen Rückführung in einer digitalen Qualitätsinfrastruktur T2 - Sensorik für die Digitalisierung chemischer Produktionsanlagen CY - Frankfurt a. M., Germany DA - 13.06.2022 KW - QI Digital KW - H2Safety@BAM KW - Wasserstoff KW - Hydrogen KW - Sensorik KW - Digitalisierung KW - Digitalisation PY - 2022 AN - OPUS4-55399 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Effect of temperature on the friction behaviour of rubber materials in hydrogen N2 - Safety and reliability are the major challenges to face for the development and acceptance of hydrogen technology. It is therefore crucial to study deeply material compatibility, in particular for tribological components that are directly in contact with hydrogen. Some of the most critical parts are sealing components that face high risk of damage due variation of pressure, temperature and mechanical stress. In this study, the friction and wear behaviour of several rubber materials was evaluated in hydrogen environment at ambient and low temperature. Tests were performed against 316L disks in a reciprocation motion. Results reveal that the hydrogen affects the friction and wear behaviour of most materials. The friction mechanism is dominated by deformation for most rubber materials at ambient temperature while sliding occurs at low temperature due to the increased hardness of the rubbers. T2 - Polytrib 2024 CY - Portorož, Slovenia DA - 03.10.2024 KW - Reciprocating sliding KW - Rubber materials KW - Hydrogen KW - Low temperature PY - 2024 AN - OPUS4-62019 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Wasserstoff - Energieträger der Zukunft N2 - Im Rahmen des internationalen Wissenschaftsfestivals, der Berlin Science Week 2021, hat die BAM in einem Beitrag das Kompetenzzentrum H2Safety@BAM, dessen Vision und die vier wissenschaftlichen Kompetenzfelder sowie den dort bearbeiteten Themen bzw. Projekten vorgestellt. T2 - Berlin Science Week 2021 CY - Berlin, Germany DA - 01.11.2021 KW - H2Safety@BAM KW - Materialeignung und -kompatibilität KW - Bauteilprüfung, -sicherheit und -zertifizierung KW - Prozess- und Anlagensicherheit KW - Sensorik, Analytik und Referenzmaterialien KW - Sicherheit KW - Vertrauen in Wasserstofftechnologien PY - 2021 AN - OPUS4-55136 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Effect of high-pressure hydrogen environment on the physical and mechanical properties of elastomers N2 - This presentation deals with the exposure of HNBR rubbers to high pressure hydrogen (100 MPa) at 120 °C for 7 and 21 days under static conditions followed by characterization of their physical and mechanical properties.The core areas include swelling, rapid gas decompression, dynamic mechanical analysis (DMA), tensile strength and compression set properties. This study will assist in expanding the knowledge base of elastomer compatibility with hydrogen and therefore contribute significantly to the selection and development of polymer materials deploying hydrogen as a future energy carrier. T2 - EHEC European Hydrogen Energy Conferecne 2022 CY - Madrid, Spain DA - 18.05.2022 KW - Rubbers KW - Hydrogen KW - Characterization PY - 2022 AN - OPUS4-62084 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo T1 - Sensors for safety and process control in hydrogen technologies N2 - This tutorial provides an overview of the utilization of sensor systems in hydrogen technologies. It discusses the necessary criteria and characteristics of sensor systems, and also demonstrates practical applications of these technologies in terms of safety and process control. Emphasis is placed on various types of sensors such as gas sensors, pressure sensors, temperature sensors, and gas flow sensors. These systems find application in monitoring and regulating operational parameters, detecting potentially dangerous situations, and activating alarm systems. T2 - Sensor and Measurement Science International - SMSI 2023 CY - Nuremberg, Germany DA - 08.05.2023 KW - H2Safety@BAM KW - SensRef KW - Hydrogen KW - Gas sensor KW - Functional safety KW - Uncertainty KW - QI-Digital PY - 2023 AN - OPUS4-57532 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska A1 - Hofmann, Detlef A1 - Johann, Sergej A1 - Tiebe, Carlo A1 - Basedau, Frank A1 - Sturm, Patrick A1 - Lay, Vera A1 - Niederleithinger, Ernst T1 - Multi-sensor conception for safe sealing structures in underground repositories N2 - The project "SealWasteSafe" of the Bundesanstalt für Materialforschung und -prüfung (BAM, Berlin) deals with sealing structures applied for underground disposal of nuclear waste from two perspectives: (1) material improvement for application in sealing constructions and (2) feasibility study regarding multi-sensor approaches to ensure quality assurance and long-term monitoring. One specimen of 150 l made of alkali-activated material, which was found innovative and suitable for sealing constructions based on preliminary laboratory studies, and, for comparison purpose, another one made of salt concrete, are manufactured with an integrated multi-sensory setup for quality assurance and long-term-monitoring. The specimens were left in their cast form and additionally thermally insulated to simulate the situation in the repository. The multi-sensory concept comprises RFID technology embedded in the specimens suppling material temperature and moisture measurements, integrated fibre optic sensing allowing strain measurement and acoustic emission testing for monitoring possible crack formation. Overall, the suitability and the functionality of the sensors embedded into and attached to strongly alkaline (pH > 13 for the AAM) and salt corrosive (NaCl) environment was proven for the first 672 h. First temperature measurement based on RFID succeeded after 626 h for the alkali-activated material and after 192 h for the conventional salt concrete. Strain measurement based on distributed fibre optic sensing turned out the alkali-activated material with > 1 mm m-1 undergoing approximately twice the compression strain as the salt concrete with strains < 0.5 mm m-1. In contrast, the acoustic emission first and single hits representing crack formation in numbers, was found for alkali-activated material half of that detected at the salt concrete. T2 - SMIRT 26 CY - Berlin/Potsdam, Germany DA - 10.07.2022 KW - SealWasteSafe KW - Monitoring KW - Acoustic emission KW - Fibre optic sensing KW - RFID technology KW - alkali-activated material PY - 2022 SP - 1 EP - 10 AN - OPUS4-55371 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kröll, Mirco T1 - Harmonised tribological testing of polymers in hydrogen N2 - The focus of this work is to study the tribological performance of polymers in hydrogen atmosphere. Additionally, tests were carried out with up to three different tribometers at two institutions. The challenge to compare and harmonise equipment, procedures, and methods is an important part of the study. T2 - PolyTrib 2024 CY - Portoroz, Slovenia DA - 03.10.2024 KW - Hydrogen KW - Tribometer KW - Comparability KW - Harmonisation KW - Oil-coupled compounds PY - 2024 AN - OPUS4-61224 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Camplese, Davide A1 - Scarponi, Giordano Emrys A1 - Eberwein, Robert A1 - Hajhariri, Aliasghar A1 - Otremba, Frank A1 - Cozzani, Valerio T1 - Modelling Fire Response of Cryogenic Liquid Hydrogen Tanks Equipped with Multilayer Insulation (MLI) Systems N2 - In the context of the growing global interest in hydrogen-based green energy, cryogenic tanks equipped with multi-layer insulation (MLI) are emerging as a leading solution for storing hydrogen in vehicles. The integrity of these systems might be threatened during fire exposure. This can trigger the degradation of the MLI materials and induce rapid pressurization of the tank with a high risk of catastrophic failure. In this work, a novel lumped model to simulate the thermal response of MLI-equipped cryogenic liquid hydrogen tanks is presented. The model integrates the accurate database “Coolprop” for hydrogen thermodynamic properties and sub-models for detailed simulation of MLI degradation, providing a realistic simulation of the experimental data obtained under normal operating conditions. The application of the model to several case studies considering different numbers of MLI layers and tank geometries demonstrates that aluminum-based MLI offers scarce protection in case of exposure to a hydrocarbon poolfire. T2 - CISAP 11 CY - Neapel, Italy DA - 15.09.2024 KW - LH2 KW - LNG KW - Cryogenic storage tank KW - Insulation KW - MLI PY - 2024 DO - https://doi.org/10.3303/CET24111076 SN - 2283-9216 VL - 111 SP - 451 EP - 456 PB - AIDIC The Italian Association of Chemical Engineering AN - OPUS4-61384 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Camplese, Davide T1 - Modelling Fire Response of Cryogenic Liquid Hydrogen Tanks Equipped with Multilayer Insulation (MLI) Systems N2 - In the context of the growing global interest in hydrogen-based green energy, cryogenic tanks equipped with multi-layer insulation (MLI) are emerging as a leading solution for storing hydrogen in vehicles. The integrity of these systems might be threatened during fire exposure. This can trigger the degradation of the MLI materials and induce rapid pressurization of the tank with a high risk of catastrophic failure. In this work, a novel lumped model to simulate the thermal response of MLI-equipped cryogenic liquid hydrogen tanks is presented. The model integrates the accurate database “Coolprop” for hydrogen thermodynamic properties and sub-models for detailed simulation of MLI degradation, providing a realistic simulation of the experimental data obtained under normal operating conditions. The application of the model to several case studies considering different numbers of MLI layers and tank geometries demonstrates that aluminum-based MLI offers scarce protection in case of exposure to a hydrocarbon poolfire. T2 - CISAP 11 CY - Neapel, Italy DA - 15.09.2024 KW - Liquefied hydrogen KW - LNG KW - Fire KW - Insulation KW - MLI PY - 2024 AN - OPUS4-61389 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Harwege, Finn T1 - Characterisation of vacuum insulation panel based cryogenic insulation N2 - Current medium to large scale hydrogen storage tanks utilize a double walled tank with vacuum and a low thermal conductivity powder as bulk fill between the two tank walls. This approach offers poor failure resistance and is not economic to build at a large scale. In NICOLHy an alternative cryogenic insulation concept using vacuum insulation panels (VIP) targeted for tanks with capacities from 40 000 m³ to 100 000 m³ is in research. VIPs consist of a gas tight envelope that surrounds a low conductivity core material. Within the envelope, a vacuum is created, which supresses convective heat transfer. Since the core material is typically very low thermal conductivity, while the envelope material has a relatively high thermal conductivity, thermal bridges where two adjoining panels meet cannot be avoided. Modeling of the thermal behaviour of VIPs exists for the building industry, but not for cryogenic temperatures or applications with multiple layers of VIPs, both of which present a new challenge. Here, these challenges and goals for the thermal modeling within the project are presented, alongside an overview over the project itself. T2 - Themenvorstellung beim BTU Arbeitsgebiet Technische Akustik CY - Cottbus, Germany DA - 23.09.2024 KW - Liquefied Hydrogen PY - 2024 AN - OPUS4-61122 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Renewable energies in Germany – Safety aspects with respect to pipelines N2 - BAM was asked to present German strategies and Projects with respect to Pipelines. Beside an introduction to BAM three Major Topics were presented: Power-to-Gas strategy in Germany, an application of distributed acoustic and fiber optic sensors for the continuous monitoring of pipes and so-called West-Jefferson Tests. T2 - 1st International Cold Regions Oil & Gas Seminar CY - Seoul, Korea DA - 07.12.2016 KW - Pipelines KW - Power-to-gas KW - Distributed acoustic sensors KW - Fiber optics PY - 2016 AN - OPUS4-38708 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Prewitz, Marc T1 - Glaskapillaren für die Wasserstoffhochdruckspeicherung N2 - Wasserstoff spielt eine wichtige Rolle im Bereich der erneuerbaren Energien. Um die hohe gravimetrische Energiedichte auszunutzen, bietet sich die die Hochdruckspeicherung an. Um die theoretische Festigkeit, die geringe Wasserstoffpermeabilität vom Werkstoff „Glas“ und das Wissen von Griffith auszunutzen, sollten Glaskapillaren zum Einsatz kommen. Glas bietet diverse Möglichkeiten solche Kapillaren anzuordnen. Es beginnt bei der Bündelung von Einzelkapillaren und geht bis hin zu ganzen Strukturen. Allerdings stellt sich auch die Frage wie die Berstdruckfestigkeit optimal ausgenutzt und dabei noch die Permeation und das mechanische Langzeitverhalten beachtet werden kann. Ziel dieser Arbeit ist es, die wichtigen Einzelkomponenten diesbezüglich zu untersuchen und einen Langzeitspeicher mithilfe von Simulationen auszulegen. T2 - Fachausschuss I der DGG CY - Würzburg, Germany DA - 09.03.2016 KW - Wasserstoff KW - Hochdruckspeicherung KW - Glaskapillaren PY - 2016 AN - OPUS4-38389 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Trust in Hydrogen Technologies - Safety Issues in the Hydrogen Value Chain N2 - In June 2020, updated in July 2023, the German government presented the National Hydrogen Strategy (NHS), its first strategy for achieving the goals of its hydrogen policy. The NHS sets out a coherent framework for action for the future production, transportation and use of hydrogen and its derivatives, including the corresponding research, innovations and investments. Various measures have been defined to achieve goals such as the decarbonization of various sectors and the market introduction of hydrogen technologies. This will ultimately lead to the introduction of many “new” technologies in many areas of our daily lives, which will only be successful if decision-makers and the public are convinced that these technologies are safe. Therefore, the safety of hydrogen technologies is an important pillar in gaining and maintaining confidence in these new technologies. Safety must keep pace with, or better still, anticipate trends in technological development in order to avoid overly conservative and expensive safety solutions, and at the same time demonstrate the usability and safety of hydrogen. Otherwise, single incidents – not necessarily explosions – can easily lead to uncertainties and therefore to a decrease in trust and acceptance. The presentation will give an overview of how safety issues are addressed in Germany. T2 - Department Seminar - Public Lecture CY - Windhoek, Namibia DA - 12.09.2025 KW - Trustworthiness KW - Hydrogen value chain KW - Safety KW - Public lecture PY - 2025 AN - OPUS4-64438 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Understanding the science and technology of hydrogen and clean energy projects N2 - As part of the Global African Hydrogen Summit, participating young people and students in Namibia and Africa learned how science and technological developments are interrelated and influence the development of a hydrogen infrastructure in Namibia. There is a global shortage of skilled workers, particularly in Namibia, who are needed now to build pilot plants and in the future to operate large-scale plants in Namibia. The presentation was intended to motivate the audience to pursue a relevant course of study and thus create prospects for the future. T2 - Global African Hydrogen Summit - Youth Programme CY - Windhoek, Namibia DA - 09.09.2025 KW - Science and technology KW - Open research topics KW - Skilled workers PY - 2025 AN - OPUS4-64437 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kröll, Mirco T1 - Tribological performance of polymer compounds in gaseous hydrogen N2 - In this study, friction and wear of conventional and alternative high performance polymer compounds, typically used for components of compressors, were investigated in gaseous hydrogen and nitrogen up to 80 bar of gas pressure. The compounds used were a commercial PEEK matrix with 10 wt.% each of PTFE, graphite, and short carbon fibres, a PPS matrix with 10 wt.% each of PTFE and graphite, and an experimental PA12 matrix with PTFE chemically coupled with an oleyl alcohol. Due to the cylindrical shape of the polymer samples, the contact area and pressure change if wear occurs. Therefore, experimental results of pre-screening tests have been used as input for FEM and an analytical model to determine the decreasing contact pressure over time. Afterwards, the outcome of the models was used to determine the duration of the experiments to reach typical contact pressures of seals in hydrogen compressors. T2 - ASMET TriboCorrosion International Conference 2025 CY - Vienna, Austria DA - 23.10.2025 KW - Hydrogen KW - Polymer KW - Tribometer KW - Comparability KW - Harmonisation KW - Oil-coupled compounds KW - Coefficient of Friction KW - Wear KW - FAIR data KW - Standardisation KW - Tribology KW - Database KW - i-TRIBOMAT PY - 2025 AN - OPUS4-64473 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Harwege, Finn A1 - Eberwein, Robert T1 - Testing of vacuum insulation panels for liquefied hydrogen storage tanks N2 - For the future use of liquefied hydrogen (LH2) as a green energy carrier, new concepts for storage tanks and in particular their insulation are necessary. The methodology applied in current LH2 tanks has some disadvantages while manufacturing and operation of large tanks that may be required in the future. While liquefied natural gas tanks exist in the necessary capacities, they are incompatible with LH2 due to its significantly lower storage temperature. In this paper, the possibility of using vacuum insulation panels (VIPs) as an alternative to the conventional double walled, powder filled vacuum insulation is presented. The two systems are introduced and compared on a conceptual level with a focus on the loss of vacuum failure mode. Furthermore, a test rig that enables the testing and quantification of thermal properties of VIP based insulations in ordinary and loss of vacuum conditions is presented. The test rig is a boil-off calorimeter using liquefied nitrogen and features a square cold surface with a side length of 3 m. An overview over the planned testing and its goals is given. KW - Liquefied Hydrogen KW - Insulation KW - Vacuum Insulation Panel KW - LH2 KW - Cryogenics PY - 2025 DO - https://doi.org/10.3303/CET2511612 SN - 2283-9216 VL - 2025 IS - 116 SP - 769 EP - 774 PB - AIDIC CY - Milano, Italy AN - OPUS4-63716 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thünemann, Andreas T1 - Structure Analysis of Functional Hydrogels with Small-Angle X-ray Scattering (SAXS) N2 - Hydrogel properties are largely determined by their network structure. Here, we report on the capabilities of SAXS methods for characterizing polymer-network gels. SAXS provides rich insight into different types and levels of nanostructural inhomogeneities in these soft matter materials. The structure analysis of alginate hydrogels, typically utilized in tissue engineering applications, will be discussed in detail. T2 - Polydays 2024 CY - Berlin, Germany DA - 30.09.2024 KW - SAXS KW - Small-angle X-ray scattering KW - Polymer KW - Gel PY - 2024 AN - OPUS4-61184 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Nationale Allianz für Wasserstoff-Sicherheit N2 - Im Rahmen des jährlich stattfindenden BAM-UBA-Behörden-Erfahrungsaustauschs wurde vorrangig Mitarbeitenden aus örtlich zuständigen Vollzugs- und Genehmigungsbehörden die in Planung befindliche Nationale Allianz für Wasserstoff-Sicherheit vorgestellt. Die Allianz besteht aus insgesamt acht Institutionen mit einer breit aufgestellten Expertise zur Sicherheit von Wasserstoff und verfolgt das Ziel, die Entwicklung fehlender Methoden und Kriterien zur technischen Sicherheit von Wasserstoff voranzutreiben, Wissenslücken zu identifizieren und diese durch gemeinsame Forschung zu schließen sowie unabhängige und wissenschaftlich fundierte Bewertungen technischer Risiken bei Wasserstoffanwendungen vorzunehmen. T2 - BAM-UBA-Behördenerfahrungsaustausch CY - Berlin, Germany DA - 02.06.2025 KW - Wasserstoff KW - Sicherheit KW - nationale Allianz PY - 2025 AN - OPUS4-63429 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Theiler, Geraldine A1 - Gradt, Thomas T1 - Comparison of the sliding behavior of several polymers in gaseous and liquid hydrogen N2 - The development of hydrogen technologies entails high safety requirements in distribution and dispensing infrastructure. Therefore, it is necessary to pursue research on material compatibility in hydrogen, especially for critical parts with tribological issues. The focus of this study is to evaluate the influence of hydrogen on a wider range of commercially available polymer materials. Thereby, the friction and wear behavior of different grades of TPE, POM, PA66, PA12, PPA, PEEK, PPS, PTFE, PAI, PI and PBI were investigated against a rotating steel disk (AISI 304). Filled and unfilled polymers from different suppliers were evaluated at room temperature in air, vacuum and hydrogen gas (H2) as well as in liquid hydrogen at - 253°C (LH2). The sliding behavior of the polymer materials is discussed by means of surface analyses, whereby special attention is paid to the formation of a transfer film. According to the results at ambient temperature, the effect of hydrogen environment on the tribological behavior of neat polymers may be related to lack of moisture, but also to saturated hydrocarbons in gaseous hydrogen. In liquid hydrogen, the best tribological performances were achieved with neat PA polymers as well as PPS and PI composites. KW - Polymers KW - Composites KW - Sliding wear KW - Hydrogen KW - Cryogenic temperature PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-597123 DO - https://doi.org/10.2474/trol.18.217 SN - 1881-2198 VL - 18 IS - 5 SP - 217 EP - 231 PB - Japanese Society of Tribologists AN - OPUS4-59712 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Sicherheit von Wasserstoff und Wasserstofftechnologien N2 - Der Nationale Wasserstoffrat (NWR) hat in einem Online-Seminar das Thema Sicherheit von Wasserstofftechnologien und aktueller Sachstand bzw. Herausforderungen in Deutschland aufgearbeitet. Dazu wurde ein Behördenvertreter (BAM), zwei Forschungsinstitutionen (FzJ und FhG IWM) sowie eine benannte Stelle (TÜV) eingeladen und die vorgestellten Themen in einem offenen Plenum diskutiert. T2 - Online-Seminar des Nationalen Wasserstoffrats CY - Online meeting DA - 07.06.2024 KW - Wasserstoff KW - Sicherheit KW - Herausforderungen KW - Elektrolyse KW - Dichtungswerkstoffe KW - Sicherheitsabstände KW - Reallabor BAM TTS KW - Nationale Allianz Wasserstoff-Sicherheit PY - 2024 AN - OPUS4-61483 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine A1 - Gradt, Thomas T1 - Comparison of the sliding behaviour of several polymers in hydrogen N2 - The work presented here deals with the friction and wear behaviour of polymer materials in hydrogen. Commercially available grades of PEEK, PA, PPA, PAI, PI and PBI were investigated at room temperature in air and hydrogen gas (H2) as well as in liquid hydrogen at -253°C (LH2). T2 - 7th World Tribology Congress, WTC 2022 CY - Lyon, France DA - 10.07.2022 KW - Friction KW - Wear KW - Polymers KW - Hydrogen KW - Cryogenic PY - 2021 SP - 1 AN - OPUS4-62089 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Anita T1 - Irrungen, Wirrungen und Lichtblicke - Überarbeitung des Gefahrguttransportrechts für Lithium- und Natrium-Ionen-Batterien N2 - Die Überarbeitung des Gefahrgutrechts hinsichtlich der Einstufung von Lithium- und Natrium - Ionen Batterien nach Gefährlichkeit trägt so einige Stilblüten - wie zuletzt den Vorschlag von 135 neuen UN Nummern für Lithiumbatterien. Die BAM trägt mit ihrer Kompetenz aus eigenen Untersuchungen und Forschung dazu bei, dass die deutsche Delegation bei den Vereinten Nationen, wo die Regelwerke weiterentwickelt werden, gezielte Vorschläge einbringen kann. Der Artikel beschreibt die aktuellen Entwicklungen. KW - Lithiumbatterien KW - Gefahrguttransport KW - Regelwerksentwicklung PY - 2024 VL - 2024 IS - 6 SP - 29 EP - 32 PB - Verkehrs-Verlag J. Fischer GmbH & Co. KG CY - Düsseldorf AN - OPUS4-62334 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Transport von Lithium-Batterien N2 - Im Bereich des Transports von Lithium-Batterien erfüllt die BAM gesetzliche Aufgaben. Diese betreffen insbesondere den Transport von Lithium-Batterien und die entsprechenden zulässigen (und von de BAM zugelassenen) Gefahrgutverpackungen. T2 - Erfa Verpackungen 2018 CY - Berlin, Germany DA - 27.09.2018 KW - Gefahrguttransport KW - Gefahrgutverpackungen KW - Lithium-Batterien PY - 2018 AN - OPUS4-47121 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mair, Georg W. A1 - Günzel, Stephan A1 - Saul, Herbert A1 - Bock, Robert T1 - Die volumenabhängige Druckbegrenzung als Maßnahme zur Konsequenzsteuerung im Wasserstofftransport N2 - Mit der technologischen Entwicklung werden auch die Transporteinheiten für Druckgase größer und die zu transportierenden Gase wie Wasserstoff deutlich über die lange als Standard geltenden 200 bar hinaus komprimiert. Damit steigt das Konsequenzpotenzial eines Zwischenfalls, das nun begrenzt werden soll, um die bisherige Praxis mit wenigen Zwischenfällen von den Maßnahmen für die neuen Entwicklungen extrem großer Transportdruckbehälter abgrenzen zu können. Hierzu wurde – ausgehend von einer technologisch und sicherheitstechnisch störenden Begrenzung des Volumens von Bergungsdruckgefäßen – das sogenannte Druck-Volumen-Produkt als Kenngröße und Konsequenzmaß vorgeschlagen. Um eine breit akzeptierte Abgrenzung der heute etablierten Druckgefäße gegenüber den zukünftigen Einheiten mit noch mehr Gasinhalt erarbeiten zu können, wurde eine Arbeitsgruppe bei den Vereinten Nationen eingerichtet, deren Weg zu ihrem Ergebnis „Einführung einer Obergrenze von 1.5 Mio. bar-Liter für das Druck-Volumen-Produkt von Druckgefäßen“ mit den Wasserstoff- spezifischen Einzelschritten „Grenze zwischen Großunfall und Katastrophe“, „Die Wirkung von Druckwellen auf den menschlichen Körper“, „Die Ausbreitung von Druckwellen“, „Der Referenzwert für die Bevölkerungsdichte“ und „Die Druckwellenberechnung“ hier dargestellt ist. Dieses Ergebnis der UN-Arbeitsgruppe wird bis 2027 zu einer verbindlichen Begrenzung des Druckvolumenproduktes in Druckgefäßen führen. KW - Risikosteuerung KW - Druck-Volumen-Produkt KW - Katastrophe KW - Bevölkerungsdichte KW - Druckwelle PY - 2024 SN - 2191-0073 VL - 14 IS - 05-06 SP - 8 EP - 17 PB - VDI Fachmedien GmbH & Co. KG CY - Düsseldorf AN - OPUS4-64309 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Polymer materials in hydrogen N2 - This presentation provides an overview of the applications and challenges related to polymer materials in hydrogen. The effects of hydrogen on polymers are described and test methods to evaluate the interactions between polymers and hydrogen are presented along with case studies. T2 - Masterstudiengang Wasserstofftechnologien DIU CY - Online meeting DA - 25.08.2023 KW - Hydrogen KW - Polymers PY - 2023 AN - OPUS4-61964 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Farhan, Muhammad A1 - Schneider, Ronald A1 - Thöns, Sebastian T1 - Corrigendum to Predictive information and maintenance optimization based on decision theory: a case study considering a welded joint in an offshore wind turbine support structure N2 - This article has been revised and republished due to substantial changes to the text of the original article, as published Online First on January 31, 2021. Most of the change were minor grammatical changes. The following changes are more significant and will be highlighted below. PY - 2022 DO - https://doi.org/10.1177/14759217211040385 SN - 1475-9217 VL - 21 IS - 4 SP - 1956 EP - 1956 PB - Sage Publications CY - London AN - OPUS4-55165 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sauer, Hannah A1 - Okpeke, Bright Ebikemefa A1 - Dzielendziak, Agnieszka Sylwia A1 - Batcke, Lars A1 - Eberwein, Robert A1 - Ehlers, Sören T1 - Comparative life cycle assessment of different vacuum insulation panel core materials for cryogenic storage tanks – with a focus on glass bubbles as a novel core material N2 - Developing a sustainable hydrogen supply chain is important in facilitating the energy transition towards climate neutrality. Hydrogen in its free form can be stored and transported either as a gas or a liquid. Due to gaseous hydrogen's comparatively low energy density, liquefied hydrogen (LH 2) is often preferred, especially with regard to long-distance transportation and storage in bulk. A notable challenge associated with LH2 is the inherent requirement to preserve it at a low temperature of -253°C. Consequently, the utilisation of thermally insulated tanks is necessary to minimise LH 2 evaporation. There is a lack of literature on the environmental impacts of insulation materials and concepts for cryogenic storage tank applications in the hydrogen supply chain. Hence, this study investigates a novel concept, namely vacuum insulation panels (VIPs), focusing on their core materials, with a view to assessing their environmental sustainability and circularity. A cradle-to-grave life cycle assessment (LCA) model is employed to investigate six distinct VIP core materials, namely, silica aerogel, rigid polyurethane foam, expanded perlite, glass fibre, fumed silica, and glass bubbles (hollow glass microspheres), with a special focus on the latter. The LCA results show that polyurethane foam and silica aerogel rank low in environmental performance, making them less suitable as primary choice. Expanded perlite is the most environmentally friendly material option, followed by glass fibre, glass bubbles, and fumed silica. Improvements to the environmental impact of glass bubbles can be achieved via the implementation of closed-loop recycling in their life cycle. T2 - The World Hydrogen Technologies Convention 2025 CY - Dublin, Ireland DA - 21.10.2025 KW - LH2 KW - Insulation KW - Life cycle assessment PY - 2025 UR - https://www.whtc2025.com/conference-proceedings SP - 65 EP - 67 AN - OPUS4-64668 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -