TY - CONF A1 - Holzwarth, Marcel A1 - Baer, Wolfram A1 - Mayer, Uwe A1 - Weihe, Stefan T1 - On the Applicability of the Master Curve Concept for Ductile Cast Iron based on experimental and microstructural results N2 - Based on the state-of-the-art research and regulations, the application of the fracture mechanics master curve (MC) concept to ferritic ductile cast iron (DCI) is being investigated in a joint research project (MCGUSS) between BAM Berlin and MPA Stuttgart. The experimental program included a basic mechanical-technological material characterization consisting of tensile, Charpy and Pellini tests. To determine the relevant loading rate for brittle fracture, instrumented C(T)25 fracture tests were performed at different loading rates at a temperature of -40°C. The relevant loading rates are 5x10^3 MPa√ms-1 and 5x10^4 MPa√ms-1. A series of dynamic fracture tests consisting of DC(T)9, C(T)25 and C(T)50 specimens were performed at MPA. BAM performed corresponding test series with SE(B)10 (pre-cracked Charpy), SE(B)25 and SE(B)140 specimens to cover the influence of specimen geometry. In total about 400 tests were performed during this project. The experimental program is complemented by extensive fractographic and metallographic studies using scanning electron microscopy and cross sectioning, as well as characterizations of the chemical composition of the material and of the morphology and distribution of the graphite particles. KJcd values were evaluated for all C(T)25 specimens and some C(T)50 and DC(T)9 specimens. First Master Curve analyses suggest that modifications on the Master Curve setup will be neccessary for instance changing the coefficient from 0.019 to 0.045. This modification requires further validation and is only one of many possible modifications. The SE(B) specimen results clearly show an inverse size effect. This does not correlate with the weakest link effect attributed to steels which dictates lower fracture toughness values for larger specimens. Due to the presence of graphite particles in the DCI material, it is currently assumed that these particles play a significant role in the failure behavior of DCI materials and the following fracture mechanism is proposed: “Specimen size-dependent arrest of local brittle fracures before global brittle failure by weakest link”. T2 - 9th SEDS Workshop: Safety of Extended Dry Storage, 20.-22. Mai 2025 CY - Garching, Germany DA - 20.05.2025 KW - Statistics KW - Dynamic fracture toughness KW - Ductile cast iron KW - Master curve KW - Safety assessment PY - 2025 SP - 1 EP - 3 AN - OPUS4-63566 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Castells-Gil, Javier A1 - Zhu, Jinjie A1 - Itskou, Ioanna A1 - Wolpert, Emma H. A1 - Hunter, Robert D. A1 - Tidey, Jeremiah P. A1 - Pedersen, Angus A1 - Solvay, Elisa A1 - Tyrrell, Helen A1 - Petit, Camille A1 - Barrio, Jesús T1 - Impact of N-heterocyclic amine modulators on the structure and thermal conversion of a zeolitic imidazole framework N2 - The zeolitic imidazole framework-8 (ZIF-8) is a crystalline porous material that has been widely employed as template to fabricate porous nitrogen-doped carbons with high microporosity via thermal treatment at high temperatures. The properties of the carbon scaffold are influenced by the pore structure and chemical composition of the parent ZIF. However, the narrow pore size distribution and microporous nature from ZIF-8 often results in low mesopore volume, which is crucial for applications such as energy storage and conversion. Here we show that insertion of N-heterocyclic amines can disrupt the structure of ZIF-8 and dramatically impact the chemical composition and pore structure of the nitrogen-doped carbon frameworks obtained after high-temperature pyrolysis. Melamine and 2,4,6-triaminopyrimidine were chosen to modify the ZIF-8 structure owing to their capability to both coordinate metal ions and establish supramolecular interactions. Employing a wide variety of physical characterization techniques we observed that melamine results in the formation of a mixed-phase material comprising ZIF-8, Zn(Ac)6(Mel)2 and crystallized melamine, while 2,4,6-triaminopyrimidine induces the formation of defects, altering the pore structure. Furthermore, the absence of heterocyclic amine in the ZIF-8 synthesis leads to a new crystalline phase, unreported to date. The thermal conversion of the modified ZIFs at 1000 °C leads to nitrogen-doped carbons bearing Zn moieties with increased surface area, mesopore volume and varying degree of defects compared to ZIF-8 derived carbon. This work therefore highlights both the versatility of heterocyclic amines to modify the structure of framework materials as well as their role in tuning pore structure in nitrogen-doped carbons, paving the way to targeted design of high-performance electrodes for energy storage and conversion. KW - Zeolitic imidazole framework KW - Heterocyclic amine KW - Triaminopyrimidine PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639177 DO - https://doi.org/10.1039/D5TA04831A SN - 2050-7488 SP - 1 EP - 13 PB - Royal Society of Chemistry (RSC) AN - OPUS4-63917 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Braga, Daniel S. A1 - Pedersen, Angus A1 - Riyaz, Mohd A1 - Barrio, Jesús A1 - Bagger, Alexander A1 - Neckel, Itamar T. A1 - Mariano, Thiago M. A1 - Winkler, Manuel E. G. A1 - Stephens, Ifan E. L. A1 - Titirici, Maria‐Magdalena A1 - Nagao, Raphael T1 - In situ structural evolution and activity descriptor of atomically dispersed catalysts during nitrate electroreduction N2 - Single‐Atom Catalysts (SAC) have emerged as a promising class of materials for various catalytic applications, including the electrochemical nitrate reduction reaction (eNO3RR) and consequently ammonia production. While the efficiency and selectivity of these materials have been extensively highlighted for the eNO3RR, the in situ evolution to their structure and composition during electrocatalysis is largely unexplored and lacks catalyst design principles. To solve this, we investigated a series of high utilization metal‐nitrogen‐carbon (MNC) SACs (M = Cr, Fe, Co, Ni, and Cu) for eNO3RR. Except for CuNC, which selectively produced nitrite, all catalysts exhibited Faradaic efficiencies (FE) for ammonia exceeding 50%. NiNC demonstrated the highest performance (FE of 78.0 ± 2.9% at −0.4 V versus reversible hydrogen electrode (RHE) at pH 13 and maximum ammonia production rate of 615.7 ± 176.5 µmol·h−1·, corresponding to an energy efficiency of 15.1 ± 1.4% at −0.6 VRHE), followed by CoNC. In situ Synchrotron X‐ray fluorescence (SXRF) mapping at various cathodic potentials (from open circuit potential to 0.0 VRHE and then −0.6 VRHE at 100 mV steps) revealed significant mobility of Ni within the carbon matrix, leading to the formation of metallic clusters from 0.0 VRHE. Similar in situ metal clustering is observed for CoNC. Structure‐activity plots are generated from both MNC literature and results obtained here, finding a clear trend between OH binding energy and turnover frequency, with the high activity of NiNC and CoNC in this work explained by their stronger OH binding in the metallic structure compared to their SAC coordination. This work therefore, reveals the structure‐activity‐stability of MNCs for eNO3RR and provides a simple descriptor for identifying highly active eNO3RR catalysts and their in situ structural evolution. KW - Single atom KW - Nitrate reduction KW - Structure-activity-selectivity KW - In situ PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-640353 DO - https://doi.org/10.1002/advs.202510282 SN - 2198-3844 VL - 12 IS - 39 SP - 1 EP - 14 PB - Wiley-VCH CY - Weinheim AN - OPUS4-64035 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Butz, Adam T1 - Experimental and analytical investigation of notched components of a Nickel based superalloy under high temperature cyclic loading N2 - While the increase in use of renewable energy sources is a necessity in times of climate change the use of gas turbines as back-up requires them to be run in a much more flexible manner in order to compensate for side effects like sudden fluctuations of energy generation. The significant changes of stress and temperature levels in turbine blades due to start-up and shut down can cause crack initiation and growth in the blades‘ alloy. The aim of this research project is to identify a model for lifetime prediction for gas turbine components made of a Nickel base superalloy under high temperature with a Focus on stress concentration points such as cooling holes. T2 - HIDA-7 Conference on Life/Crack Assessment & Failures in Industrial Structures, UK CY - Portsmouth, UK DA - 15.05.2017 KW - LCF KW - Gas turbine KW - Service life model PY - 2017 AN - OPUS4-42274 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Morcillo, Dalia A1 - Winckelmann, Alexander A1 - Oelze, Marcus A1 - Leonhardt, Robert A1 - Schmidt, Anita A1 - Richter, Silke A1 - Recknagel, Sebastian A1 - Vogl, Jochen A1 - Panne, Ulrich A1 - Abad Andrade, Carlos Enrique T1 - Exploring Age-Induced Lithium Isotope Fractionation in Lithium-Ion Batteries using Microwave-Induced Cold Nitrogen Plasma Mass Spectrometry N2 - This study explores Microwave-Inductively Coupled Atmospheric-pressure Plasma Mass Spectrometry (MICAP-MS) as a cost-effective alternative to Multi-Collector Inductively Coupled Plasma Mass Spectrometry (MC-ICP-MS) for analyzing lithium isotopic composition in lithium-ion batteries (LIBs). We investigate the performance of MICAP-MS in measuring Li isotope ratios in new and aged commercial lithium cobalt oxide (LCO) batteries. Our results show that MICAP-MS, operating under cold plasma conditions at 800 W with an 8 mm torch position, achieves results metrologically compatible with MC-ICP-MS, with a precision ranging from 0.6‰ to 3.4‰ for δ7Li values. MICAP-MS benefits from a dielectric resonator for uniform plasma, better ion velocity control, and higher energy efficiency. Optimal settings were identified with dwell times of 10 ms for 6Li and 1 ms for 7Li. The study of LIBs revealed that 6Li migrates towards the anode over multiple charge–discharge cycles, causing 7Li to accumulate in the cathode, a fractionation effect that becomes more pronounced with prolonged cycling. MICAP-MS provides a cost-effective, precise alternative to MC-ICP-MS, with lower operational costs and enhanced portability, advancing the study of isotopic fractionation and aging in lithium-ion batteries. KW - MICAP-MS KW - Lithium KW - Battery aging KW - Lithium isotopes KW - Nitrogen plasma KW - Isotope fractionation KW - lithium cobalt oxide KW - LCO PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-643777 DO - https://doi.org/10.1039/d4ja00324a SN - 0267-9477 SP - 1 EP - 11 PB - Royal Society of Chemistry (RSC) AN - OPUS4-64377 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Abad Andrade, Carlos Enrique T1 - Data-Driven Spectrochemical Sensing for Elemental and Isotopic Analysis—from Energy Systems to Biomedicine N2 - High-resolution optical spectrometers generate spectra containing tens of thousands of data points per sample. Picometre-scale isotope shifts, matrix-induced line broadening, and strong inter-feature correlations render classical peak fitting unreliable. Current analytical challenges, therefore, require rigorous algorithms able to expose latent structure, quantify uncertainty, and remain chemically interpretable. The research program presented in this lecture integrates state-of-the-art spectrochemical instrumentation with mathematically disciplined data models. Principal Component Analysis and Partial Least Squares provide chemically meaningful latent variables, while gradient-boosted decision trees or deep neural networks (ANNDL) capture residual non-linearity without sacrificing traceability. All models are trained on isotope-enriched or synthetically generated spectra and distributed with full validation workflows. Two research areas illustrate this strategy: (1) Isotopic analytics for materials, environment, and medicine. (2) Data-fusion diagnostics for battery ageing and failure. T2 - Temple University: Mechanical Engineering Transformative Science and Technology Engineering Lecture Series CY - Philadelphia, PA, USA DA - 02.10.2025 KW - Isotope KW - Data analysis KW - Machine learning KW - Elemental analysis KW - Battery PY - 2025 AN - OPUS4-64877 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Abad Andrade, Carlos Enrique T1 - Tracking Lithium-Ion Battery Ageing via Lithium Isotope Fractionation N2 - Lithium-ion batteries power portable devices, electric vehicles, and stationary power grids, yet hidden aging reactions still shorten their service life and raise concerns about cost and safety. An analytical proxy is needed to report these reactions and accelerate product development, quality control, and recycling. Here, we demonstrate that subtle shifts in the natural 7Li/6Li ratio accurately record the two decisive stages of cell aging, solid-electrolyte interphase (SEI) formation and field-driven aging, which can be detected using multi-collector ICP-MS. Because Li is easily stripped from digested electrodes or electrolyte in a one-step cation-exchange column, high-purity solutions reach the spectrometer in minutes. A streamlined MC-ICP-MS run yields a δ7LiLSVEC precision of 0.4 ‰, enabling dozens of battery fractions to be analyzed per day. Applying the workflow to LiCoO2 coin cells as models, sampled from pristine to 700 cycles, reveals a clear isotopic narrative. During the first ≈45 cycles, 7Li leaves the LiCoO2 lattice, dissolves into the electrolyte, and is locked in the SEI on graphite, driving cathode δ7Li from +8 to –10 ‰ and raising the anode to +13 ‰ while capacity drops by 10 %. After the interphase matures, the electric field takes over: the lighter 6Li migrates faster to the anode, 7Li accumulates in the contracting Li1-xCoO2 lattice, and the bulk separation factor rises to α≈1.045 by 700 cycles. The δ7Li curve flattens roughly 70 cycles before capacity falls to 80%, providing an early warning of end-of-life. Isotopic gradients scale linearly with impedance growth, SEI thickness, and crack density confirmed by LA-ICP-MS mapping, FIB-SEM, XANES, and EXAFS. Although each data point requires one cell, lithium-isotope fractionation provides direct, element-specific, and structural fatigue insight unavailable from non-destructive tests. The straightforward chemistry and fast MC-ICP-MS routine make the approach practical for targeted aging studies, additive screening, and forensic autopsies, complementing high-throughput electrochemical methods and supporting the design of longer-lived batteries. T2 - SciX 2025 CY - Covington, KY, USA DA - 05.10.2025 KW - Isotope KW - Lithium KW - MC-ICP-MS KW - MICAP-MS KW - Isotope fractionation KW - Battery PY - 2025 AN - OPUS4-64879 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mesquita Silva da Veiga, Marcia T1 - Ultrasonic-assisted leaching of Li and Co from black mass using deep eutectic solvent N2 - The recovery of critical metals from spent lithium-ion batteries is a key strategy for sustainable resource management and the circular economy. Conventional hydrometallurgical processes typically rely on strong mineral acids and elevated temperatures, which, although effective, generate hazardous waste and demand high energy inputs. As a greener alternative, deep eutectic solvents (DES) combine low toxicity, non-volatility, simple synthesis, and tunable physicochemical properties, making them promising media for selective metal recovery1-2. Here, we report for the first time the use of ultrasound (US) to assist the leaching of Li and Co from LiCoO₂ black mass employing a deep eutectic solvent based on choline chloride and formic acid (ChCl:HCOOH, 1:2 molar ratio). The DES was synthesized at 90 °C for 3 h under stirring (300 rpm) and was characterized in terms of its molecular structure and formation by 1H-NMR and FT-IR, as well as by its viscosity and density. For each experiment, ~0.100 g of LiCoO2 was treated with 5 g of DES-FA in an ultrasonic bath (35 kHz, 60 °C) for different irradiation times (30–120 min), followed by three sequential extractions. All measurements were performed by ICP OES. Lithium solubilization reached ~80% at 90 min, while cobalt extraction was stabilizing at ~79% after 120 min. The enhanced performance under US is attributed to sonochemical effects that promote cavitation and microjets, leading to the disruption of particle agglomerates, the thinning of diffusion layers, and the generation of highly reactive local environments. These processes accelerate deintercalation and mass transfer within the solid–liquid interface. Combined with the mild acidity of DES-FA, which enables simultaneous leaching of both metals while favoring faster kinetics for Li, ultrasound provided a synergistic effect that enhanced the overall process and preserved the distinct extraction profiles of Li and Co. The extraction behavior of the two metals can be explained by their different speciation in the DES-FA medium. Cobalt is likely reduced from Co(III) to Co(II) by formic acid and stabilized through the formation of chloro-complexes such as [CoCl4]2- with chloride anions from ChCl, favoring its solubilization. In contrast, lithium does not form stable complexes with chloride under these conditions. It is primarily extracted as a solvated cation, stabilized by the extensive hydrogen-bond network of the DES. This difference accounts for the faster leaching kinetics observed for Li compared to Co. Selective recovery was achieved by pHcontrolled precipitation, with cobalt oxalate at pH 4-5 and lithium carbonate at pH 10. The Eco-Scale score of 85 confirmed the greenness of the method. This pioneering approach highlights the potential of coupling DES chemistry with ultrasound. Together, they represent a sustainable and efficient route for recovering critical metals from battery waste. T2 - 17th Rio Symposium on Atomic Spectrometry (17th RSAS) CY - São Pedro City, Brazil DA - 09.11.2025 KW - Black mass KW - deep eutectic solvent KW - Lithium KW - Cobalt KW - Lithium-ion battery recycling KW - Ultrasound-assisted extraction KW - Lithium and cobalt recovery KW - Green hydrometallurgy PY - 2025 AN - OPUS4-64956 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Askar, Enis T1 - Challenges for hydrogen technologies - Activities of H2Safety@BAM N2 - In this presentation the drivers for the rise of hydrogen technologies are outlined and main challenges for the market ramp-up are shown. Finally, the activities and capabilities of the competence center H2Safety@BAM are characterized and some of the current projects at BAM adressing the main challenges for hydrogen technologies are presented focussing on the hydrogen transport and infrastructure. T2 - Wasserstoff-Dialog - Stakeholder-Konferenz des Wasserstoff-Kompass CY - Berlin, Germany DA - 10.10.2022 KW - Hydrogen strategy KW - ModuH2Pipe KW - Hydrogen transport KW - Hydrogen infrastructure KW - Liquid hydrogen (LH2) PY - 2022 AN - OPUS4-57065 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - Comprehensive Standardisation of the Hollow Specimen Technique for Tests in High-Pressure Hydrogen Gas N2 - The hollow specimen technique is a simple and economical method that has the potential to overcome the limitations and complement the current techniques for qualifying metallic materials under highpressure hydrogen gas. In this technique, an axial hole is manufactured in a tensile specimen, which is then filled with hydrogen gas, sealed, and placed in a standard testing machine. This method requires significantly lower amounts of hydrogen, resulting in fewer safety measures and does not require complex equipment or a specialised laboratory, unlike the conventional autoclave technique. Initial studies have demonstrated the feasibility of assessing hydrogen effects in metallic materials using the hollow specimen technique. This led to the establishment of the committee ISO/TC 164/SC 1/WG 9 to standardise the method, however, there are still open questions that currently prevent the technique from being standardised for hydrogen testing. These open questions are being addressed in the H2HohlZug project, which is presented in this contribution. T2 - Oxford - EPRI Hydrogen Embrittlement Workshop CY - Oxford, United Kingdom DA - 23.06.2024 KW - Hollow Specimen Technique KW - High-pressure Gaseous Hydrogen KW - Hydrogen Embrittlement KW - Tensile Testing PY - 2024 AN - OPUS4-60501 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sobol, Oded T1 - Hydrogen assisted cracking phenomena in duplex stainless steels elucidated by in- and ex-situ ToF-SIMS experiments N2 - In the presented research, the high potential and abilities of secondary ion mass spectrometry (ToF-SIMS) to detect and locally map the hydrogen distribution in two types of duplex stainless steels are shown. The research validates certain proposed mechanisms by combining ToF-SIMS with high-resolution scanning electron microscopy and electron-backscattered diffraction. The combination of data from several techniques on the same region was conducted in this field for the first time by applying data treatment of the ToF-SIMS raw data and data fusion approach. This powerful combination of methods allows reviewing of the occurring processes related to hydrogen assisted cracking. The step beyond the state of the art in this field was gained here by developing permeation and mechanical loading experiments within the ToF-SIMS during chemometric imaging of the hydrogen distribution in the microstructure. The research presents the necessary correlation between the hydrogen distribution and the resulted structural changes, the diffusion behavior in a duplex microstructure and stress induced diffusion of hydrogen by applying external load at the microscale. T2 - 6th WMRIF Early Career Scientist Summit CY - NPL Teddington UK DA - 18.06.2018 KW - ToF-SIMS KW - Duplex stainless steel KW - LDX KW - EBSD KW - Data-fusion PY - 2018 AN - OPUS4-46865 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Junias, Josua Kondja T1 - Prediction of Explosion Characteristics of Hydrogen Mixtures Using Machine Learning Models N2 - An understanding of Hydrogen-Oxygen/Air-Diluents gas mixtures combustion characteristics and their accurate prediction is crucial for ensuring the safety of hydrogen-related applications, reducing accidents risk, and protecting lives and property. Hydrogen detonation propagations are characterized by the detonation cell size, used to quantitatively predict for a mixture to detonate including, among others, the initiation energy, critical and minimum tube diameters. For the prediction of explosion limits, detonation run-up-distances and cell sizes, various empirical, semi-empirical and numerical models can be found in literature. These models are usually limited to a narrow range of explosion process or geometrical experimental parameters. Moreover, based on the limited availability of the detonation cell widths measurements, current estimation models are seemingly inaccurate. Machine learning models can be utilized to make justifiable prediction on the detonation cell sizes of hydrogen-air mixtures and other gaseous explosive mixtures cell sizes, explosion limits or run-up distance to detonation based on the mixture type, temperature, pressure, equivalence ratios as well as on geometrical parameters with consideration of highly diverse experimental data measurements uncertainties. Therefore, an up-to date database for explosion characteristics will be established and machine learning models will be developed, trained, tested, and validated using experimental data to predict explosion characteristics of hydrogen mixtures. The models predicted results will be validated against existing models. It will be tested whether machine learning models are able to predict the explosion characteristics of hydrogen mixtures with better accuracy and more comprehensively than conventional empirical and numerical models to be found in literature. T2 - Combustion Institute 40th International Symposium CY - Milano, Italy DA - 21.07. 2024 KW - Prediction, detonation KW - Machine Learning KW - Flammability limits PY - 2024 AN - OPUS4-60769 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nietzke, Jonathan T1 - Evolution of tensile testing methodologies for hydrogen embrittlement in austenitic steels: a comparative study N2 - The energy transition towards hydrogen utilisation has increased the demand for reliable testing methods to evaluate the susceptibility of metallic materials to hydrogen degradation. However, traditional electrochemical pre-charging techniques have limitations in represent-ing realistic gaseous hydrogen exposure conditions. This study presents three comparative analyses of tensile testing methodologies, focusing on the differences between electrochem-ical pre-charging, gaseous pre-charging, and in-situ testing using hollow specimens for aus-tenitic steels AISI 304L and 316L type austenitic steels. Based on the results obtained, the first comparison reveals that electrochemically pre-charged and gaseously pre-charged specimens exhibit different behaviours regarding the impact on the mechanical properties. This effect can be retraced to the varying distribution of hydrogen throughout the specimens. Although comparable embrittlement was observed for similar hydrogen concentrations, the relationship appears to be non-systematic. The second comparison evaluates the performance of pre-charged hollow specimens (300°C, 100 bar, 21 days) in comparison to hollow specimens tested in-situ under 200 bar hydrogen during slow strain rate tensile tests (SSRT). While pre-charged specimens show a slight de-crease in elongation at fracture and a noticeable decrease in reduction of area (RA), in-situ tested specimens exhibit significantly more pronounced embrittlement. This is in accord-ance with the results of Michler et. al. In the third comparison, geometry effects between pre-charged conventional and pre-charged hollow specimens are explored. In this case, the hydrogen effect appears to be of the same order of magnitude for both specimen types, although some differences are ob-served. The study's findings underscore the importance of considering differences between test methods when assessing materials’ compatibility with hydrogen. It specifically emphasises the need for in-situ testing with gaseous hydrogen to better represent real conditions in ap-plications within the hydrogen sector. Furthermore, the study provides an initial compari-son between conventional and hollow specimens, demonstrating their capability to reveal hydrogen effects. However, additional research is essential to enhance the comparability of results yielded by these testing methods. T2 - European Conference on Fracture 2024 CY - Zagreb, Croatia DA - 26.08.2024 KW - Hollow Specimen Technique KW - Hydrogen KW - Austenitic Stainless Steel KW - Hydrogen Testing KW - AISI 316L PY - 2024 AN - OPUS4-60929 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nietzke, Jonathan T1 - The relationship between surface condition and the influence of hydrogen on the mechanical properties of additively manufactured 316L N2 - The following contribution presents the analyses of additively manufactured (AM) 316L using hollow specimens at 200 bar hydrogen and a strain rate of 1E-5 s-1. The work includes a comparison of three types of hollow specimens: mechanically extracted from fully additively manufactured cylinders, near-net-shape additively manufactured specimens, i.e. as printed, and specimens made of conventional 316L. AM specimens were manufactured via powder bed fusion with laser beam of metals (PBF-LB/M). For the near-net-shape specimens the inner hole remained without any mechanical processing. The inner holes of the cylindric specimens were manufactured by drilling with subsequent honing. The susceptibility to hydrogen embrittlement was found to be strongly dependent on the surface being in contact with hydrogen. While specimens with a clean surface had a relative reduction of area (RRA) of around 78 %, those with an as-printed surface showed a significantly larger RRA of around 90 %. One possible reason for this are oxide layers formed due to small amounts of oxygen during the AM-process. Further research is required to determine if the lower effect on the mechanical properties is permanently for as printed parts or e.g. time dependent. Additionally, further work with variation in the nominal strain rate is required. T2 - IIW 77th Annual Assembly 2024 CY - Rhodes, Greece DA - 07.07.2024 KW - Austenitic steel 316L KW - Additive manufacturing KW - PBF-LB/M KW - Hydrogen degradation KW - Hydrogen embrittlement KW - Hollow specimen technique PY - 2024 AN - OPUS4-60618 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nietzke, Jonathan T1 - Stainless Steels and Hydrogen Applications N2 - The contribution was presented at the Stainless Steel World Conference 2022. The presentation shows the influence of hydrogen on the mechanical properties of steel. Some test methods are shown and selected results are presented. T2 - Stainless Steel World Conference 2022 CY - Maastricht, Netherlands DA - 27.09.2022 KW - Gaseous hydrogen KW - Hydrogen Embrittlement KW - Hydrogen assisted cracking KW - SSRT PY - 2022 AN - OPUS4-55913 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - Hollow Specimen Technique for Tests in High-Pressure Hydrogen Gas: The Path Towards Standardisation and the Case Study of a Pipeline Steel and its Weld N2 - The hollow specimen technique is a simple method that has the potential to make material qualification with gaseous pressurized hydrogen widely applicable for the hydrogen industry at low cost. The feasibility of this method has been demonstrated in several studies, leading to the establishment of an ISO committee for its standardization. Questions have emerged during this process, that currently prevent the method from being standardized for hydrogen testing. These questions relate to specimen geometry, specimen manufacturing and gas quality and are being systematically addressed in the TransHyDE-H2HohlZug project. The aim is to close the identified gaps towards the standardization of this method for hydrogen testing. This contribution presents the structure and milestones of the project, followed by the results regarding the influence of specimen production and its response to hydrogen effects. Depending on the production method, different roughness and residual stresses can be expected on the inner hole surface of the specimens. This is of importance since an increase in stress concentration sites have been found to be associated to a higher severity of hydrogen effects. This influence has been investigated after applying the following machining processes: a) drilled only; b) drilled and reamed; c) drilled and honed; d) electro-discharge machining (EDM) and honed; e) EDM and reamed. Roughness measurements using a profilometer, electron back-scatter diffraction (EBSD) analysis and microhardness tests have been performed previous to mechanical testing to infer on the effect of the different production methods on the surface of the inner hole. Next, the specimens were mechanically tested via slow strain rate tensile tests in a argon and in hydrogen, both at 150 bar and room temperature. Here, a strain-rate sensibility analysis was also performed to identify an optimal strain-rate for the mechanical tests. Based on the results an optimal production method is identified and proposed. T2 - ASTM Conference on Hydrogen Materials CY - La Rochelle, France DA - 03.06.2025 KW - Hydrogen KW - Hydrogen Embrittlement KW - Hollow Specimen Technique KW - High-Pressure Gaseous Hydrogen KW - Austenitic Stainless Steel KW - H2HohlZug KW - TransHyDE KW - Tensile Test KW - Pipeline Steel PY - 2025 AN - OPUS4-63329 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sobol, Oded T1 - Challenges with metallic materials in hydrogen technologies N2 - The contribution was presented in the Joint European Summer School in Athens as part of several contributions from BAM in the field of hydrogen safety. These presentations are given in order to provide an overview about the activities of BAM as part of the competence center H2Safety@BAM T2 - JOINT EUROPEAN SUMMER SCHOOL (JESS) CY - Athens, Greece DA - 12.09.2022 KW - Gaseous hydrogen KW - Hydrogen Embrittlement KW - Hydrogen assisted cracking PY - 2022 AN - OPUS4-55822 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Battistella, Beatrice T1 - Isotopic Fractionation in Lithium-Ion Batteries (LIBs): A New Key to Understand Degradation N2 - The presentation summarizes the research work of division 1.6 on Li isotope fractionation in Li-ion batteries (LIB). This work interrogates whether changes in Li isotopic distribution in LIB components can be used as a diagnostic tool to monitor interphases growth at the electrodes surfaces and as a benchmark to track battery degradation. For this purpose, different analytical techniques have been employed to study the electrodes of commercial and lab-scale cells, providing bulk (MC-ICP-MS) and local (GD-MS, LA-ICP-MS) information about the Li isotope distribution changes upon cells cycle aging. The results show Li isotope fractionation in full Li ion cells upon aging, suggesting that the 6Li accumulation on the surface of the negative electrode might be used as a new benchmark to track the solid electrolyte interphase growth T2 - ADLERSHOFER KOLLOQUIUM Analytik – Abteilung 1 CY - Berlin, Germany DA - 28.10.2025 KW - MC-ICP-MS KW - Li-ion Batteries KW - Li Isotopes KW - LA-ICP-MS KW - GD-MS PY - 2025 AN - OPUS4-64511 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander A1 - Schukar, Marcus A1 - Breithaupt, Mathias A1 - Kriegsmann, Andreas T1 - Distributed Fibre Optic Monitoring of Hydrogen Storage Composite Pressure Vessels for Automotive Use N2 - We present our research work on the condition monitoring of hydrogen storage composite pressure vessels using distributed fibre optic sensors. The sensing fibres are integrated into the composite structure by wrapping them over the polymer liner in the helical and circumferential direction during the manufacturing process of the carbon fibre reinforced polymer. The following use of optical backscatter reflectometry allows for continuous condition monitoring and precise detection and localization of structural damages during the entire service life. To account for the time-dependent strength degradation of the composite pressure vessels, both slow burst and ambient hydraulic cycling tests, respectively, were conducted on five 70 MPa pressure vessels with integrated fibre optic sensors. The results achieved via distributed fibre optic strain sensing demonstrate a near linear strain response to pressure suitable for sensitive condition monitoring and confirm the required robustness of the selected sensor solution. T2 - DGZfP-Jahrestagung 2025 CY - Berlin, Germany DA - 26.05.2025 KW - Distributed fibre optic sensor (DFOS) KW - Composite pressure vessel KW - Optical backscatter reflectometry KW - Slow burst test KW - Ambient hydraulic cycling test PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-653067 DO - https://doi.org/10.58286/32344 SP - 1 EP - 8 PB - NDT.net AN - OPUS4-65306 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. A1 - Becker, Ben A1 - Duffner, Eric A1 - John, Sebastian T1 - Storage systems for CGH2- systematic improvement of RC&s composite storage systems for compressed hydrogen - systematic improvement of regulations for more attractive storage units N2 - Hydrogen is an attractive energy carrier that requires high effort for safe storage. For ensuring safety they have to undergo a challenging approval process. Relevant standards and regulations for composite cylinders used for the transport of for on-board storage of hydrogen are currently based on deterministic (e.g. ISO 11119-3) or semi-probabilistic (UN GTR No. 13) criteria. This paper analysis the properties of such methods in regards to the evaluation of load cycle strength. Their characteristics are compared with the probabilistic approach of the BAM. Based on Monte-Carlo simulations, the available design range (mean value and scatter of strength criteria) of current concepts were exemplarily estimated. The aspect of small sample sizes is analysed and discussed with respect to the evaluation procedures. T2 - 10th International Conference on Sustainable Energy and Environmental Protection CY - Bled, Slovenia DA - 27.06.2017 KW - Probabilistic KW - Hydrogen KW - Composite KW - Cylinder KW - Regulations KW - Load cycles KW - GTR 13 KW - ISO 11119 PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-416820 SN - 978-961-286-054-7 DO - https://doi.org/10.18690/978-961-286-054-7 SP - 1 EP - 10 PB - University of Maribor Press CY - Maribor, Slovenia AN - OPUS4-41682 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Olejko, Lydia A1 - Bald, Ilko T1 - FRET efficiency and antenna effect in multi-color DNA origami-based light harvesting systems N2 - Artificial light harvesting complexes find applications in artificial photosynthesis, photovoltaics and light harvesting chemical sensors. They are used to enhance the absorption of light of a reaction center which is often represented by a single acceptor. Here, we present different light harvesting systems on DNA origami structures and analyze systematically the light harvesting efficiency. By changing the number and arrangement of different fluorophores (FAM as donor, Cy3 as transmitter and Cy5 as acceptor molecules) the light harvesting efficiency is optimized to create a broadband absorption and to improve the antenna effect 1 (including two energy transfer steps) from 0.02 to 1.58, and the antenna effect 2 (including a single energy transfer step) from 0.04 to 8.7, i.e. the fluorescence emission of the acceptor is significantly higher when the light-harvesting antenna is excited at lower wavelength compared to direct excitation of the acceptor. The channeling of photo energy to the acceptor proceeds by Förster Resonance Energy Transfer (FRET) and we carefully analyze also the FRET efficiency of the different light harvesting systems. Accordingly, the antenna effect can be tuned by modifying the stoichiometry of donor, transmitter and acceptor dyes, whereas the FRET efficiency is mainly governed by the spectroscopic properties of dyes and their distances. KW - DNA origami KW - Light-harvesting KW - FRET KW - Antenna effect PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-405867 UR - http://pubs.rsc.org/en/content/articlelanding/2017/ra/c7ra02114c#!divAbstract DO - https://doi.org/10.1039/C7RA02114C VL - 7 IS - 39 SP - 23924 EP - 23934 PB - The Royal Soc. of Chemistry AN - OPUS4-40586 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Schneider, Ronald T1 - Time-variant reliability of deteriorating structural systems conditional on inspection and monitoring data N2 - The current practice of operating and maintaining deteriorating structural systems ensures acceptable levels of structural reliability, but it is not clear how efficient it is. Changing the current prescriptive approach to a risk-based approach has great potential to enable a more efficient management of such systems. Risk-based optimization of operation and maintenance strategies identifies the strategy that optimally balances the cost for controlling deterioration in a structural system with the achieved risk reduction. Inspections and monitoring are essential parts of operation and maintenance strategies. They are typically performed to reduce the uncertainty in the structural condition and inform decisions on future operation and maintenance actions. In risk-based optimization of operation and maintenance strategies, Bayesian updating is used to include information contained in inspection and monitoring data in the prediction of the structural reliability. All computations need to be repeated many times for different potential inspection and monitoring outcomes. This motivates the development of robust and efficient approaches to this computationally challenging task. The reliability of deteriorating structural systems is time-variant because the loads on them and their capacities change with time. In most practical applications, the reliability analysis of deteriorating structural systems can be approached by dividing their lifetime into discrete time intervals. The time-variant reliability problem can then be represented by a series of time-invariant reliability problems. Using this methodology as a starting point, this thesis proposes a novel approach to compute the time-variant reliability of deteriorating structural systems for which inspection and monitoring data are available. The problem is formulated in a nested way in which the prediction of the structural condition is separated from the computation of the structural reliability conditional on the structural condition. Information on the structural condition provided by inspections and monitoring is included in the reliability assessment through Bayesian updating of the system deterioration model employed to predict the structural condition. The updated system reliability is obtained by coupling the updated deterioration model with a probabilistic structural model utilized to calculate the failure probability conditional on the structural condition. This approach is the first main outcome of this thesis and termed nested reliability analysis (NRA) approach. It is demonstrated in two numerical examples considering inspected and monitored steel structures subject to high-cycle fatigue. An alternative – recently developed – approach, which also follows the strategy of discretizing time, describes deteriorating structural systems with hierarchical dynamic Bayesian networks (DBN). DBN combined with approximate or exact inference algorithms also enable the computation of the time-variant reliability of deteriorating structural systems conditional on information provided by inspection and monitoring data. In this thesis – as a proof of concept – a software prototype is developed based on the DBN approach, which can be used to assess the reliability of a corroding concrete box girder for which half-cell potential measurements are available. This is the second main outcome of this thesis. Both approaches presented in this thesis enable an integral reliability analysis of inspected and monitored structures that accounts for system effects arising from (a) the correlation among deterioration states of different structural elements, (b) the interaction between element deterioration and system failure, and (c) the indirect information gained on the condition of all unobserved structural elements from inspecting or monitoring the condition of some structural elements. Thus, both approaches enable a systemwide risk-based optimization of operation and maintenance strategies for deteriorating structural systems. The NRA approach can be implemented relatively easily with subset simulation, which is a sequential Monte Carlo method suitable for estimating rare event probabilities. Subset simulation is robust and considerably more efficient than crude Monte Carlo simulation. It is, however, still sampling-based and its efficiency is thus a function of the number of inspection and monitoring outcomes, as well as the value of the simulated event probabilities. The current implementation of the NRA approach performs separate subset simulation runs to estimate the reliability at different points in time. The efficiency of the NRA approach with subset simulation can be significantly improved by exploiting the fact that failure events in different years are nested. The lifetime reliability of deteriorating structural systems can thus be computed in reverse chronological order in a single subset simulation run. The implementation of the DBN approach is much more demanding than the implementation of the NRA approach but it has two main advantages. Firstly, the graphical format of the DBN facilitates the presentation of the model and the underlying assumptions to stakeholders who are not experts in reliability analysis. Secondly, it can be combined with exact inference algorithms. In this case, its efficiency neither depends on the number of inspection and monitoring outcomes, nor on the value of the event probabilities to be calculated. However, in contrast to the NRA approach with subset simulation, the DBN approach with exact inference imposes restrictions on the number of random variables and the dependence structure that can be implemented in the model. T3 - BAM Dissertationsreihe - 168 KW - Reliability KW - Structural systems KW - Deterioration KW - Bayesian analysis KW - Inspection KW - Monitoring KW - Zuverlässigkeit KW - Tragstrukturen KW - Schädigungsprozesse KW - Bayes'sche Analyse KW - Inspektion KW - Monitoring PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-512977 SN - 1613-4249 VL - 168 SP - 1 EP - 188 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-51297 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stengel, Dominik A1 - Mehdianpour, Milad T1 - Finite element modelling of electrical overhead line cables under turbulent wind load N2 - This paper presents a finite element model of an overhead transmission line using so called cable elements which allow reproducing the cable's nonlinear characteristics accurately employing only a few elements. Aerodynamic damping is considered in the equation of motion by taking into account the relative velocity between the flow of the wind and the moving structure. The wind flow itself is simulated by wave superposition making necessary assumptions on the lateral correlation between the wind velocities along the cable length. As result from the simulation, the following conclusions can be drawn. The first natural frequency of generally used wide spanning cables lies well below 1 Hz where also most of the energy content of the wind excitation is to be expected. Aerodynamic damping is significant for the moving cables holding very low structural damping which leads to a suppression of resonant amplification. This is particularly of interest regarding the support reaction which is dominated by the mean value and the so called background response. The latter is mostly influenced by the randomness of the wind flow, especially lateral to the main wind direction. KW - Nonlinear Finite Element Formulations KW - Nonlinear Equation of Motion KW - Turbulent Wind Excitation PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-304567 DO - https://doi.org/10.1155/2014/421587 SN - 2314-6494 SN - 2356-766X VL - 2014 IS - Article ID 421587 SP - 1 EP - 8 PB - Hindawi Publ. CY - New York, NY ; Cairo AN - OPUS4-30456 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hüllmann, Dino A1 - Kohlhoff, Harald A1 - Neumann, Patrick P. ED - Bársony, I. ED - Zolnai, Z. ED - Battistig, G. T1 - Embedded control of a PMSM servo drive without current measurements N2 - A permanent-magnet synchronous motor (PMSM) servo drive for lightweight robotic platforms that have a high torque demand at low rotational speeds has been developed. First, a current-independent torque controller is derived and cascaded with a speed and position controller, while merely an encoder is used as a sensor device in combination with a speed estimator. Finally, the speed estimator output is compared to gyroscope measurements and the overall functioning is verified on a real system. T2 - 30th Eurosensors Conference - Eurosensors 2016 CY - Budapest, Hungary DA - 04.09.2016 KW - BLDC KW - PMSM KW - Motor control KW - Servo drive KW - Optical incremental encoder PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-388973 DO - https://doi.org/10.1016/j.proeng.2016.11.487 SN - 1877-7058 VL - 168 SP - 1671 EP - 1675 PB - Elsevier B.V. CY - Amsterdam, Netherlands AN - OPUS4-38897 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kuroiwa, T. A1 - Zhu, Y. A1 - Inagaki, K. A1 - Long, S. A1 - Christopher, S. A1 - Puelles, M. A1 - Porinsky, M. A1 - Hatamleh, N. A1 - Murby, J. A1 - Merrick, J. A1 - White, I. A1 - Saxby, D. A1 - Caciano de Sena, R. A1 - Dominguez de Almeida, M. A1 - Vogl, Jochen A1 - Phukphatthanachai, Pranee A1 - Fung, W.-H. A1 - Yau, H.-P. A1 - Okumu, T. O. A1 - Kang'iri, J. N. A1 - Tellez, J. A. S. A1 - Campos, E. Z. A1 - Galvan, E. C. A1 - Kaewkhomdee, N. A1 - Taebunpakul, S. A1 - Thiengmanee, U. A1 - Yafa, C. A1 - Tokman, N. A1 - Tunc, M. A1 - Can, S. Z. T1 - Report of the CCQM-K123: trace elements in biodiesel fuel N2 - The CCQM-K123 key comparison was organized by the Inorganic Analysis Working Group (IAWG) of CCQM to assess and document the capabilities of the national metrology institutes (NMIs) or the designated institutes (DIs) to measure the mass fractions of sodium, calcium, potassium, magnesium phosphorous and sulfur in biodiesel fuel (BDF). The National Metrology Institute of Japan (NMIJ) and National Institute of Standards and Technology (NIST) acted as the coordinating laboratories. Results were submitted by 11 NMIs and DIs. The participants used different measurement methods, though most of them used inductively coupled plasma-mass spectrometry (ICP-MS), isotope dilution technique with ICP-MS and inductively coupled plasma-optical emission spectrometry (ICP-OES) with microwave acid digestion. The material was quite challenging and a number of questions were raised at the IAWG meeting. Concerning S, the variation in S results between participants, particularly those using IDMS methods was discussed at the IAWG meeting. BAM, NIST and NMIJ reviewed their experimental conditions, results and/or uncertainty calculations for IDMS. According to the additional evaluation and investigation, the variances between the revised results became smaller than the original one, the revised results were overlapping between IDMS measurements of S content at the k=2 level. It is not possible to calculate a KCRV with values being modified after submission. It was concluded that this KC does not support S measurements. Accounting for relative expanded uncertainty, comparability of measurement results for each of Na, Ca, K, Mg and P was successfully demonstrated by the participating NMIs or DIs. It is expected that sodium, calcium, potassium, magnesium and phosphorus at mass fractions greater than approximately 0.1 mg/kg, 0.1 mg/kg, 0.05 mg/kg, 0.05 mg/kg and 0.1 mg/kg respectively in biodiesel fuel and similar matrices (fuels and oils etc.) can be determined by each participant using the same technique(s) employed for this key comparison to achieve similar uncertainties mentioned in the present report. Furthermore, the results of this key comparison can be utilized along with the IAWG core capability approach. KW - Biodiesel KW - Fuel KW - Sulphur KW - Reference measurement PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-393941 UR - http://iopscience.iop.org/article/10.1088/0026-1394/54/1A/08008/meta DO - https://doi.org/10.1088/0026-1394/54/1A/08008 SN - 0026-1394 SN - 1681-7575 VL - 54 SP - Tech. Suppl. 2017, 08008, 1 EP - 47 PB - IOP Publishing CY - Bristol, UK AN - OPUS4-39394 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Kanzler, Daniel T1 - Zuverlässigkeitsanalyse von digitalen Radiographie-Systemen bei der Prüfung von realen Materialdefekten N2 - Die zerstörungsfreie Prüfung (ZfP) ist aus solchen Bereichen unseres Lebens nicht mehr wegzudenken, in denen Schäden mit hohen Folgekosten oder Gefährdungen von Menschenleben entstehen können (Beispiele: Transportwesen, Energieerzeugung, Chemieindustrie). In der Praxis kann ein Prüfsystem an seine Grenzen geraten, z.B. bei kleinen Defekten. Defekte mit kritischer Größe werden möglicherweise nicht detektiert. Daher müssen probabilistische Bewertungsverfahren das Prüfsystem beschreiben. Es wird eine objektive Qualitätskennzahl gesucht, auf deren Basis die Anwendbarkeit der Prüfmethode definiert werden soll. Die Auffindwahrscheinlichkeit (engl. probability of detection - POD) erfüllt diese Anforderung. Die POD zeigt auf Basis des Zusammenhangs und der Streuung der Daten, ob das Verfahren für die Prüftätigkeit akzeptiert werden kann oder noch verbessert werden muss. Das ursprüngliche POD-Verfahren wurde für quasi eindimensionale Defekte in dünnen Luftfahrtbauteilen entwickelt. In der industriellen Realität ist diese Bewertung ein Balanceakt zwischen Statistik und Durchführbarkeit: Die Prüfung soll mit realen Defektdaten für die spätere Produktion des Bauteils (bzw. wiederkehrende Wartungsprüfung) bewertet werden. Doch die notwendige Gegenüberstellung zwischen Schliffdaten, für die Erfassung der wahren Defektgröße von räumlich ausgeprägten Defekten und dem Signal eines ZfP-Systems stellt sich als herausfordernde und kostenintensive Aufgabe heraus. Sowohl die Aufstellung eines gemeinsamen Koordiantensystems als auch die Beschreibung und Angleichung der Daten stellen eine notwendige Vorarbeit dar. In dieser Arbeit wird ein mögliches Vorgehen entwickelt, dass im Weiteren eingesetzt werden kann. Während in der Literatur zum Thema POD häufig die Begrenzung des Einsatzes einer eindimensionalen POD (POD mit einem Defektparameter) für reale Defekte bereits erkannt wurde, soll außerdem in dieser Arbeit das Verfahren auf der Signalseite umfassender erweitert werden, um die Einbeziehung realer Defekte in die POD-Bewertung zu ermöglichen. Hierfür werden mit Hilfe dieser Arbeit zwei wesentliche Neuerungen in der POD-Bewertung eingeführt: 1. Die Anzeigenfläche wird als wichtiges Indiz zur Detektion in die Bewertung eingeführt. Dabei zeigt der Ansatz einer Observer-POD, bei dem der Detektierbarkeit eines Defekts beschrieben wird, eine Möglichkeit in die Bewertung zu erweitern. Jedoch wird die notwendige Datenanzahl die für eine Observer-POD selten mit Experimenten erreicht. Daher schlagen wir die Einführung eines Glättungsalgorithmus vor, um auch auf der Basis von wenigen Daten die Flächenabhängigkeit zu erfassen. Der Algorithmus wird hierbei durch simulierte Daten auf seine Funktionsfähigkeit überprüft, bevor er auf reale Defekte angewendet wird. Gleichzeitig helfen die simulierten Daten einen Vergleich zu den vorhergegangenen Ansätzen zu ermöglichen. 2. Darüber hinaus reichen die Daten der realen Defekte häufig nicht aus, um die statistische Forderung zu gewährleisten, so dass es notwendig, wird künstliche Defekte mit einzubeziehen. Deshalb sollen die vorhanden künstlichen Defekte in Form von Referenzdefekten mit einbezogen werden, um die statistische Grundlage zu erhöhen. Für die Prüfung von Referenzdefekten sind jedoch wichtige Einflussgrößen (z.B. Oberflächenrauhigkeit) nicht vorhanden. Wegen der unterschiedlichen Aussagekraft der Daten und zur Vermeidung einer zu optimistischen Abschätzung, ist eine einfache Mischung der Daten ausgeschlossen. Um realen Defekten eine Möglichkeit dafür zu schaffen, dass die Eigenschaften der realen Defekte angemessen auf das Ergebnis der Bewertung des Verfahrens Einfluss nehmen können, wird eine gewichtete Kombination der Defektdaten für die Bewertung vorgestellt. Das Vorgehen wird am Beispiel der radiographischen Prüfung einer elektronenstrahlgeschweißten Naht durchgeführt. Die Schweißnaht verbindet den Deckel zur Außenwand eines Kupferbehältern, der für die spätere Endlagerung von verbrauchten Brennstäben aus Kernkraftwerken entwickelt wurde. Die Messergebnisse stammen aus von der Firma Posiva Oy, dem zuständigen Unternehmen für die Endlagerung von verbrauchten Brennstäben aus Kernkraftwerken in Finnland. Hierbei stellt die POD-Bewertung ein wichtiges Element in der Gesamtrisikobewertung für das Endlagersystem dar. T3 - BAM Dissertationsreihe - 153 KW - Radiographie KW - POD KW - Zuverlässigkeit KW - Zerstörungsfreie Prüfung (ZfP) KW - Probabilistische Bewertung PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-388723 SN - 978-3-9818270-1-9 SN - 1613-4249 VL - 153 SP - iii EP - 134 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-38872 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kinne, Marko A1 - Thöns, Sebastian T1 - Fatigue Reliability Based on Predicted Posterior Stress Ranges Determined from Strain Measurements of Wind Turbine Support Structures N2 - In the present paper, an approach for updating the continuous stress range distribution of a welded connection of a wind turbine support structure with predicted information from strain measurements is presented. Environmental conditions, such as wind or, in offshore fields, waves and currents, in combination with rotor excitations generate cyclic stresses affecting the reliability of welded joints of the support structure over the service life. Using strain measurements, these conditions can be monitored, and the resulting stress ranges, under consideration of measurement, mechanical and material uncertainties, can be reconstructed. These stress ranges can be used as an input for updating the prior probability density function (PDF) of the stress ranges predicted by the overall dynamics and a detailed design analysis. Applying Bayesian probability theory and decision theoretical implications, the predicted posterior probability density of the stress ranges is calculated based on the design information and uncertainties. This approach is exemplified, and it is shown how the predicted stress ranges and the design stress ranges are distributed. The prior and the predicted posterior stress ranges are used for a reliability calculation for potentially entering a pre-posterior decision analysis KW - Strain measurements of wind turbine support structures KW - Bayesian updating of stress ranges KW - Posterior fatigue reliability PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-572663 DO - https://doi.org/10.3390/en16052225 VL - 16 IS - 5 SP - 1 EP - 26 PB - MDPI AN - OPUS4-57266 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kinne, Marko A1 - Farhan, Muhammad A1 - Schneider, Ronald A1 - Thöns, Sebastian T1 - Influence of the structural integrity management on the levelized cost of energy of offshore wind: a parametric sensitivity analysis N2 - The levelized cost of energy (LCoE) is an important measure to quantify the macro-economic efficiency of an offshore wind farm and to enable a quantitative comparison with other types of energy production. The costs of the structural integrity management - which is required to ensure an adequate lifetime reliability of the turbine support structures - are part of the operational expenditures of an offshore wind farm. An optimization of the structural integrity management may reduce the operational expenditures and consequently the LCoE. However, the effect of the structural integrity management on the LCoE is hardly known. To investigate this effect, this paper presents a sensitivity analysis of the LCoE of a generic offshore wind farm. The probabilistic models of the parameters influencing the LCoE are based on a literature study including an explicit model for the structural integrity management. The analysis reveals that LCoE may potentially be reduced if an optimization of the structural integrity management enables a service life extension. T2 - International Probabilistic Workshop 2022 CY - Stellenbosch, South Africa DA - 08.09.2022 KW - Structural integrity management KW - Levelized cost of energy KW - Sensitivity analysis PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-572724 DO - https://doi.org/10.14311/APP.2022.36.0090 VL - 36 SP - 90 EP - 98 PB - Acta Polytechnica CTU Proceedings AN - OPUS4-57272 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sauermoser-Yri, M. A1 - Veldurthi, N. A1 - Wölfle, C. H. A1 - Svartvatn, P. J. A1 - Flo Hoem, S. O. A1 - Lid, M. J. A1 - Bock, Robert A1 - Palko, J. A1 - Torgersen, J. T1 - On the porosity-dependent permeability and conductivity of triply periodic minimal surface based porous media N2 - With the fast development in the field of additive manufacturing, triply periodic minimal surface (TPMS) based porous media have recently found many uses in mechanical property tuning. However, there is still a lack of understanding in their porosity-dependent permeability and electrical as well as thermal conductivity. Here, we perform finite volume simulations on the solid and void domains of the Schoen gyroid (SG), Schwarz primitive (SP) and Schwarz primitive beam (SPB) TPMS with porosities between 63% and 88% in Ansys Fluent. A simple cubic lattice (CL) of equivalent porosity served as reference. The SPB and CL showed up to one order of magnitude higher permeabilities than the SG and SP. However, SG and SP have about 1.3 and 2.6 times the electrical and thermal conductivity of SPB and CL, respectively. Furthermore, the properties of SPB and CL are largely affected by the surface area density, whereas tortuosity variation does not impact permeability and conductivity to a major extent. Finally, empirical relations are adapted to describe the presented data and thus, they may enable future designers of TPMS based porous structures to fine-tune the geometries according to the requirements on permeability and electrical as well as thermal conductivity. KW - Metals and Alloys KW - Surfaces, Coatings and Films KW - Biomaterials KW - Ceramics and Composites PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-585250 DO - https://doi.org/10.1016/j.jmrt.2023.09.242 SN - 2238-7854 VL - 27 SP - 585 EP - 599 PB - Elsevier B.V. AN - OPUS4-58525 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bock, Robert A1 - Mair, Georg W. A1 - Tiebe, Carlo A1 - Melzer, Michael A1 - Klaus, Christian A1 - Nattuveettil, Keerthana A1 - Engel, Thomas A1 - Prager, Jens T1 - Eine digitale QI für technische Anlagen: Beispiel Wasserstofftankstelle (H2) N2 - Mit der Initiative QI-Digital werden völlig neue Perspektiven für das Sicherheitsmanagement und die Qualitätssicherung technischer Anlagen erschaffen. Unsere Forschung im Kontext einer Wasserstofftankstelle zeigt, wie digitale Innovationen und Verfahren die Herausforderungen effizienter und verlässlicher Qualitätssicherung für komplexe Anlagen bewältigen können. In diesem Vortrag werden Potentiale und Beispiele der digitalen QI für technische Anlagen demonstriert und diskutiert: Moderne Anlagenüberwachung mit digitalen Zwillingen und KI sowie Kalibriermanagement mithilfe digitaler Kalibrierscheine und elektronischem Siegel. T2 - 2. QI Digital Forum CY - Berlin, Germany DA - 10.10.2023 KW - Wasserstoff KW - Sensorik KW - Qualitätsinfrastruktur KW - Digitalisierung KW - Druckspeicher KW - Verwaltungsschale PY - 2023 AN - OPUS4-58599 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bock, Robert T1 - Pilotprojekt Wasserstofftankstelle - Session 2: Verlässliche Wassertofftankstellen N2 - Was ist QI? Qualitätsinfrastruktur – Das Zusammenwirken von nationalen Institutionen im Bereich der Metrologie, Normung und Standardisierung, Akkreditierung, Konformitätsbewertung und Marktüberwachung, mit dem Ziel die Qualitätssicherung bei Produkten und Prozessen in Deutschland zu gewährleisten. Unser Ziel ist es, unsere bewährte Qualitätsinfrastruktur (QI) noch besser zu machen und so einen Beitrag zur Lösung von sozioökonomischen, ökologischen und technologischen Herausforderungen unserer Zeit zu leisten. Eine der bedeutendsten technologischen Herausforderungen unserer Zeit ist die Digitalisierung. Die zentralen Akteure der deutschen QI wollen diese digitalisieren. Beteiligte Institutionen sind aktuell BAM (Konformitätsbewertungen in bestimmten Bereichen), DAKKS (Akkreditierung), DIN/DKE (Normung), PTB (Metrologie). Wir wollen also ein Reallabor errichten, das die Wertschöpfungskette einer Tankstelle abbildet, also eine Wasserstofftankstelle beinhaltet, die dann mit erweiterter Sensorik ausgestattet werden soll. Somit sollen digitale Prozesse abgebildet werden können sowie sensorgestützte Verfahren zur qualitätsgesicherten Datenerfassung und -auswertung genutzt werden. Diese gesammelten Daten sollen dann in eine Dateninfrastruktur eingehen und mithilfe eines Datenmanagementsystems sowie künstlicher Intelligenz in einem Digitalen Zwilling zusammenlaufen, der die digitale Prozessüberwachung der Sicherheit möglich macht. Schließlich sollen die in QI Digital entwickelten digitalen Strukturelemente der QI erprobt werden, insbesondere die QI Cloud, Smart Standards und digitalen Zertifikate. Im Zusammenspiel ermöglicht das unter anderem die Entwicklung von Predictive Maintenance Verfahren für: 1. die Optimierung von Wartungszyklen und Minimierung von Ausfallzeiten Erhöhung der Betriebssicherheit durch frühzeitige Identifikation kritischer Zustände im Gesamtsystem 2. Entwicklung verlässlicher Qualitäts- und Sicherheitsstandards  3. Digital-gestützte Risikobeurteilung und Konformitätsbewertung Die im Pilotprojekte betrachteten Sicherheitsaspekte sind also zusammenfassbar als: a) Auswirkungsbetrachtungen bei möglichen Fehlfunktionen oder Defekten b) Die genannte vorrauschauende Instandhaltung und damit verbundene Lebensdauerprognose, die in Kombination eine bessere allgemeine Verfügbarkeit garantieren sollen Als Grundlage hierfür benötigen wir aber Änderungen im Bereich der technischen Regeln und Normen, um die neuen digitalen Werkzeuge zuzulassen und nutzbar zu machen. T2 - QI Forum 2022 CY - Berlin, Germany DA - 11.10.2022 KW - Wasserstoff KW - Qualitätsinfrastruktur KW - Digitalisierung PY - 2022 AN - OPUS4-61356 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Orellana Pérez, Teresa T1 - QI Digital Use Case Hydrogen Refueling Station N2 - BAM is part of the “Quality Infrastructure Digital” (QI Digital) initiative of the German Federal Ministry for Economic Affairs and Climate Action (BMWK). This initiative aims at coordinating a large cooperation project, “QI Digital” for making German and European quality management systems fit for the digital transformation. It is a fact that the digitization of new products and services is occurring much faster than quality management systems can be accordingly updated. Thus, the digital transformation of quality management is necessary to preserve the competitiveness of the German and European industries that stand for quality and safety in the global market. The Use Case “Reliable Hydrogen Refueling Station” of QI Digital aims at creating new solutions that are transferable to other technical systems and at further developing standards and technical rules as a contribution to technology transfer and innovation. T2 - 4th German-Korean Hydrogen Conference CY - Seoul, Republic of Korea DA - 31.10.2023 KW - Hydrogen refueling station KW - Digital quality infrastructure PY - 2023 AN - OPUS4-59303 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bock, Robert A1 - Mair, Georg W. T1 - Pilotprojekt "Verlässliche Wasserstofftechnologie" - Beispielanwendung für eine technische Anlage N2 - Kurzvorstellung des Pilotprojektes Verlässliche Wasserstofftechnologie in QI Digital. Anwendung der QI Digital Werkzeuge an einer technischen Anlage beispielhaft gezeigt anhand von sechs im Projekt entwickelten Demonstratoren. Unser erklärtes Ziel ist die Unterstützung des Markthochlaufs von Wasserstofftechnologien durch Digitalisierung der QI. Bei der Qualitätsinfrastruktur von technischen Anlagen geht es vor allem die Themen QI Dokumentation und Zugänglichkeit, Verfügbarkeit der Anlage und Informationen darüber, sowie Inspektionszyklen mit zeitaufwändigen und teuren manuellen Prüfungen. Mit dem Übergang zu einer digitalen QI streben wir hier an, eine kontinuierliche Überwachung des momentanen Gesundheitszustandes der Anlage und automatisierter Dokumentation hierüber, die fälschungssicher und vertraulich zugänglich gemacht werden kann, zu erreichen. Hierzu sollen die im Gesamtprojekt entwickelten QI Digital Werkzeuge zum Einsatz kommen. T2 - QI Forum 2024 CY - Berlin, Germany DA - 09.10.2024 KW - Wasserstoff KW - Qualitätsinfrastruktur KW - Digitalisierung PY - 2024 AN - OPUS4-61354 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kehr, Torsten T1 - Project QI-Digital - Quo vadis Use Case H2 Refueling Station? N2 - As a part of the QI-Digital cooperation project, BAM is setting up a hydrogen refuelling station research platform at the Test site for Technical Safety in Horstwalde. Based on this platform, BAM intends to develop, to test and to optimize new measurement techniques as well as data acquisition and processing methods for hydrogen refuelling stations and their periphery in close cooperation with partners from the quality infrastructure and industry. The presentation will introduce the hydrogen refuelling station use case and provide insights into the issues and research goals of the associated subprojects. T2 - H2-Colloquium of the Competence Centre „H2SAFETY@BAM” CY - Online meeting DA - 16.02.2022 KW - Hydrogen KW - Safety KW - QI-Digital PY - 2022 AN - OPUS4-54361 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Aspekte einer digitalen Lebenslaufakte (Impulsvortrag) N2 - Durch Einsatz neuer Technologien im Transport von komprimiertem Wasserstoff konnte eine Verdreifachung des Nutzlastverhältnisses erreicht werden. Diese neuen Speicher auf den Transportfahrzeugen müssten aber anders auf ihre Sicherheit überprüft werden, als dies heute gefordert wird. Mit dem Markthochlauf Wasserstoff vervielfacht sich zudem die Anzahl der Transporteinheiten. Da sich im Zuge der neuen H2-Transportfahrzeuge aber auch die Anzahl der einzelnen Speicher pro Fahrzeug etwa verzwanzigfacht hat, kommen die Kapazitäten für die erforderliche wiederkehrende Prüfung an ihre Grenzen. Dies könnte evtl. durch eine entsprechende Erhöhung der Prüfkapazitäten gelöst werden. Da dies aber weder praktisch machbar ist noch technisch wirklich sinnvoll, müssen alternative Ansätze z.B. durch digital erfasste zerstörungsfreie Prüfkonzepte gesucht werden. Hierzu bedarf es aber einer Lebenslaufakte, die beginnend von der Definition einer Bauweise über die Baumusterprüfung, Zulassung, Herstellung, erstmalige Prüfung, Verwendung und wiederkehrenden oder begleitenden Prüfungen bis zum Verschrotten alle Daten erfassen und verwalten kann. Eine solche Lebenslaufakte könnte auch als eine Art digitaler Produktpass (DPP) verstanden werden. T2 - QI-digital Forum 2023 CY - Berlin, Germany DA - 10.10.2023 KW - Wasserstoffspeicher KW - Lebenslaufakte KW - Digitaler Produktpass DPP KW - Wiederkehrende Prüfung KW - Lebensdauerüberwachung PY - 2023 AN - OPUS4-58559 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo T1 - Error prevention, damage prevention, and safety management in hydrogen technologies N2 - This tutorial presents requirements and properties of sensor systems and shows application examples of these technologies for safety and process control for hydrogen technologies. Sensor systems are widely used in hydrogen technologies. The focus is on gas sensors as well as sensors for pressure, temperature, and gas flow. These systems are applied, among other things, for monitoring and control of operating conditions, indication of hazardous conditions and triggering of alarms. To integrate the error avoidance and loss prevention strategy into hydrogen technologies. This includes the implementation of preventive measures as elements of safety management to identify and eliminate potential sources of error. In addition, training should be specifically focused on avoiding errors and the safe use of hydrogen technologies. A well-thought-out strategy for error prevention makes a significant contribution to preventing accidents and increasing overall safety when using hydrogen. T2 - Sensor and Measurement Science International (SMSI) CY - Nuremberg, Germany DA - 06.05.2025 KW - Hydrogen KW - Safety Management KW - Gas Sensors KW - Performance Testing PY - 2025 AN - OPUS4-63280 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Flege, J. I. T1 - BTU-BAM Graduate School “Trustworthy Hydrogen” N2 - Beim Online-Meeting des Wasserstoffnetzwerks Lausitz mit dem Titel "Wirtschaft trifft Wissenschaft und Forschung" wurde die BTU-BAM-Graduiertenschule Trustworthy Hydrogen vorgestellt. Es handelt sich um die erste Graduiertenschule in Deutschland, die sich mit der Vertrauenswürdigkeit von Wasserstoff beschäftigt und die einzigartigen Kompetenzen von BAM und BTU zur Ausbildung der nächsten Generation von interdisziplinären Wasserstoff-Wissenschaftlern bündelt. N2 - The BTU-BAM graduate school Trustworthy Hydrogen was presented at the online meeting of the Lausitz Hydrogen Network entitled "Business meets Science and Research". It is the first graduate school in Germany to focus on the trustworthiness of hydrogen and combines the unique competencies of BAM and BTU to train the next generation of interdisciplinary hydrogen scientists. T2 - Lausitzer Netzwerktreffen DurcH2atmen "Wirtschaft trifft Wissenschaft und Forschung" " CY - Online meeting DA - 22.11.2022 KW - H2Safety@BAM KW - Graduate School KW - Trustworthy Hydrogen KW - Graduiertenkolleg PY - 2022 AN - OPUS4-56443 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Competence Centre H2Safety@BAM N2 - Deutschland hat mit verschiedenen Ländern Energiepartnerschaften geschlossen, darunter auch mit Japan. Im Rahmen des 3. Treffens der Wasserstoff-Arbeitsgruppe wurde das strategische Vorgehen beider Länder zu Entwicklungen von Wasserstoffrichtlinien, Zertifizierung und Sicherheit vorgestellt und diskutiert. Die BAM hat in einem Vortrag wichtige Themen aus dem Bereich der Sicherheitsforschung sowie zu sicherheitstechnischen Fragestellungen über die Wertschöpfungskette vorgestellt. Außerdem wurde das Arbeitsprogramm und ausgewählte Projekte des Kompetenzzentrums H2Safety@BAM vorgestellt. N2 - Germany has concluded energy partnerships with various countries, including Japan. During the 3rd meeting of the Hydrogen Working Group, the strategic approach of both countries on developments of hydrogen guidelines, certification and safety was presented and discussed. BAM gave a presentation on important topics in the field of safety research and on safety-related issues along the value chain. Furthermore, the work program and selected projects of the competence center H2Safety@BAM were presented. T2 - 3rd Meeting of the Hydrogen Working Group - Japanese-German Energy Partnership CY - Berlin, Germany DA - 27.02.2023 KW - Hydrogen KW - Japanese-German energy partnership KW - Safety KW - H2Safety@BAM PY - 2023 AN - OPUS4-57126 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Offene Fragestellungen bei der Sicherheit von H2-Anwendungen aus Sicht der BAM N2 - Um die Energiewende voranzubringen, wird neben dem Ausbau der Erneuerbaren Energien ein schneller Markthochlauf bei Wasserstoff-Erzeugung, Transport und Anwendung angestrebt. Dieser Markthochlauf geht derzeit insbesondere einher mit Fragen der Wirtschaftlichkeit und der Umsetzung einer Serienfertigung von Elektrolyseuren. Bei Fragen der Sicherheit wird üblicherweise auf das bestehende Regelwerk verwiesen. Da der Umgang mit Wasserstoff und die Technologien zur Wasserstoff- Erzeugung nicht neu sind, geht man davon aus, dass durch die Einhaltung der bestehenden Regelwerke die Anlagen ausreichend sicher sind. Aber ist das wirklich so? Decken die bestehenden technischen Regelwerke alle derzeitigen Entwicklungen im Zusammenhang mit der Wasserstofferzeugung und -nutzung in allen notwendigen Facetten ab, um die Sicherheit zu gewährleisten? Der Experten-Workshop soll die Möglichkeit bieten, sich über die Sicherheit bei Wasserstofferzeugung und -nutzung auszutauschen sowie offene Fragestellungen und Lücken im Regelwerk zu identifizieren. Hierzu sind sowohl Impulsvorträge als auch ein offener Austausch mit allen Teilnehmenden geplant. T2 - GRS-Online-Workshop Wasserstoffsicherheit CY - Online meeting DA - 06.07.2023 KW - H2Safety@BAM KW - Wasserstoffsicherheit KW - Regelwerke PY - 2023 AN - OPUS4-57908 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Forschungsnetzwerk Wasserstoff N2 - Die BAM beteiligt sich sehr aktiv am Forschungsnetzwerk Wasserstoff, eines von neun Forschungsnetzwerken Energie der Bundesregierung. Der Vortragende ist Sprecher des Cluster IV "Sicherheit, Akzeptanz und nachhaltige Markteinführung" vom Forschungsnetzwerk und wurde vom Geschäftsführer des Center of Safety Excellence GmbH gebeten, die aktuellen Forschungsbedarfe des Netzwerkes, die in der Expertenempfehlung 2023 dem BMWK übermittelt wurden, vorzustellen. T2 - Beiratssitzung des Center of Safety Excellence GmbH CY - Online meeting DA - 20.04.2023 KW - H2Safety@BAM KW - Forschungsnetzwerk Wasserstoff KW - Forschungsbedarfe KW - Sicherheit PY - 2023 AN - OPUS4-57373 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hörmann, Anja Franziska T1 - (Grazing Incidence) Small-angle X-ray Scattering for STOP N2 - We remind project partners of the principles of SAXS, GISAXS and X-ray reflectivity and their applicability to the antimicrobial particles and coatings developed within the STOP project. T2 - M25 project meeting: Surface Transfer of Pathogens (STOP) CY - Bucharest, Romania DA - 19.09.2024 KW - X-ray Scattering KW - Nanomaterial PY - 2024 AN - OPUS4-62774 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Hydrogen - Safety of Energy Carriers N2 - Eine sichere Versorgung mit Energie stellt für moderne Industriegesellschaften eine elementare Grundvoraussetzung dar. Inwieweit in Deutschland die Energiewende im Sinne von zum Beispiel Energiepolitik, Förderung aber auch gesellschaftlicher Entwicklung gestaltet wird, wurde im Rahmen der 12. Wildauer Wissenschaftswoche diskutiert. Die BAM hat einen Beitrag zum Thema Sicherheit von Energieträgern beigetragen und das Kompetenzzentrum H2Safety@BAM vorgestellt. N2 - A safe supply of energy is a fundamental prerequisite for modern industrial societies. The extent to which the energy turnaround is being shaped in Germany in terms of, for example, energy policy, promotion, but also social development was discussed during the 12th Wildau Science Week. BAM contributed to the topic of safety of energy sources and presented the competence center H2Safety@BAM. T2 - 12. Wildauer Wissenschaftswoche CY - Wildau, Germany DA - 27.02.2023 KW - Hydrogen KW - Safety KW - H2Safety@BAM PY - 2023 AN - OPUS4-57125 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Holtappels, Kai T1 - Impulse zum Hochlauf einer Wasserstoffwirtschaft in Deutschland N2 - Wasserstoff als sauberer, vielseitig einsetzbarer Energieträger spielt bei der dringend benötigten Energiewende eine entscheidende Rolle. Die Etablierung einer Wasserstoffwirtschaft wird tiefgreifende Auswirkungen auf verschiedene Sektoren der deutschen Wirtschaft haben und diese grundlegend transformieren. Die vorliegende Publikation fokussiert Herausforderungen und Maßnahmen für den Hochlauf einer Wasserstoffwirtschaft in Deutschland und ist in einem knapp einjährigen Multi-Stakeholder-Dialog gemeinsam mit führenden Expertinnen und Experten aus Industrie, Wissenschaft, Gesellschaft (NGOs) sowie Vertretern aus der Politik-entstanden. KW - Wasserstoff KW - Markthochlauf KW - Zukunftsdialog KW - Herausforderungen PY - 2025 SN - 978-3-911670-07-4 SP - 1 EP - 62 PB - VDI Verein Deutscher Ingenieure e.V. CY - Düsseldorf AN - OPUS4-63941 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Eberwein, Robert T1 - Untersuchung der Gefährdung von Personen und Bauwerken in Folge des Versagens von LNG-Kraftstoffspeichern für Fahrzeuge in Tunneln N2 - Liquefied Natural Gas (LNG) aus regenerativen Quellen, stellt einen potenziellen Kraftstoff für den Schwer- und Fernverkehr des Straßenverkehrs dar. Gegenüber seinen positiven Eigenschaften zu dem in diesem Verkehrssektor häufig verwendeten Kraftstoff Diesel birgt der Kraftstoff aber auch Gefahren für Personen und Bauwerke durch seine sehr niedrige Temperatur bei der Speicherung von ca. -160 °C und seine Explosionsfähigkeit in der Gas-Phase. In der Arbeit wurde sich mit der Gefährdung von Personen und Bauwerken hinsichtlich der von LNG ausgehenden Gefahren in Tunneln auseinandergesetzt. Tunnel stellen besonders schützenswerte Bauwerke dar, da aus vorhergehenden Störfällen in Tunneln bekannt ist, dass diese mit hohen Personen-, Bauwerks-, und Volkswirtschaftlichen-Schäden einhergehen können. Untersuchungsschwerpunkt bei der Bewertung von Gefährdungen durch LNG stellte eine Ereigniskaskade bestehend aus Freisetzung, Verdampfung, Stoffausbreitung und Zündung des sich gebildeten explosionsfähigen LNG-Gas/Luft-Gemisches dar. Mit dem Ziel eine solche Ereigniskaskade realitätsnah vorhersagen und zukünftig hierzu Risikoanalysen durchführen zu können wurden innerhalb der Arbeit Parameterstudien sowie Kalibrierungen und Validierungen gegenüber experimentellen Untersuchungen durchgeführt. Mit den Modellen wurden in der Arbeit exemplarische Fallbeispiele zu Störfällen untersucht. Ergebnisse dieser waren, dass Gefährdungen insbesondere von flüssigem LNG nach dessen Freisetzung und der Verbrennung von LNG-Gas/Luft-Gemischen ausgingen. N2 - Liquefied Natural Gas (LNG) from regenerative sources is a potential fuel for heavy and long-distance road traffic. In contrast to its positive properties compared to diesel, which is often used in this transport sector, the fuel also contains hazards from its very low storage temperature of approx. -160 °C and its explosiveness in the gas phase for personal and structural safety. The dissertation dealt with the dangers to persons and infrastructures according to the hazards by LNG in tunnels. Tunnels are especiallyworth protecting structures since it is known from previous incidents in tunnels that they can go hand in hand with high damage to the people, the structure, and the economy. The main focus of the investigation into the assessment of hazards from LNG was an event cascade consisting of release, evaporation, dispersion, and ignition of the explosive LNG-vapor/air-mixture formed. To realistically predict such an event cascade and being able to carry out risk analyzes for this purpose in the future, parameter studies such as calibrations and validations were carried out concerning experimental investigations. Exemplary case studies on incidents were examined in the thesis with the validated models. The results of this were that there were especially hazards in particular from liquid LNG after its release and the combustion of LNG-vapor/air-mixtures. KW - Verflüssigtes Erdgas KW - Erneuerbare Energien KW - Numerische Strömungsmechanik KW - Sicherheitstechnik KW - Liquefied Natural Gas KW - LNG KW - Renewable fuels KW - CFD KW - Safety engineering PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-521145 DO - https://doi.org/10.14279/depositonce-11346 SP - 1 EP - 240 PB - TU Berlin CY - Berlin AN - OPUS4-52114 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hajhariri, Aliasghar A1 - Eberwein, Robert A1 - Perrone, Luca Pakj A1 - Cozzani, Valerio A1 - Otremba, Frank A1 - Seidlitz, Holger T1 - Study the impact of spacer at thermal degradation process of MLI-based insulation in fire condition N2 - To reduce CO2 emissions, energy carriers such as hydrogen are considered to be a solution. Consumption of hydrogen as a fuel meets several limitations such as its low volumetric energy density in gas phase. To tackle this problem, storage as well as transportation in liquified phase is recommended. To be able to handle this component in liquid phase, an efficient thermal insulation e.g., MLI insulation is required. Different studies have been addressed the vulnerability of such insulation against high thermal loads e.g., in an accident engaging fire. Some of research works have highlighted the importance of considering the MLI thermal degradation focusing on its reflective layer. However, limited number of studies addressed the thermal degradation of spacer material and its effect on the overall heat flux. In this study, through systematic experimental measurements, the effect of thermal loads on glass fleece, glass paper as well as polyester spacers are investigated. The results are reported in various temperature and heat flux profiles. Interpreting the temperature profiles revealed that, as the number of spacers in the medium increases, the peak temperature detectable by the temperature sensor on the measurement plate decreases. Each individual spacer contributes to mitigating the radiative energy received by the measurement plate. Stacks of 20–50 spacers (this is the number of layers in commercial MLI systems applied for liquid hydrogen applications) can potentially reduce the thermal radiation by 1–2 orders of magnitude. An empirical correlation to predict a heat flux attenuation factor is proposed, which is useful for further numerical and analytical studies in the temperature range from ambient to 300 ◦C. KW - Cryogenic KW - Liquid Hydrogen KW - Multi-Layer Insultation KW - Heat Transfer KW - Hydrogen Storage Safety PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-614919 DO - https://doi.org/10.1016/j.jlp.2024.105461 SN - 0950-4230 VL - 92 SP - 1 EP - 7 PB - Elsevier Ltd. AN - OPUS4-61491 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tschirschwitz, Rico T1 - Sicherheitstechnische Fragestellungen bei statioären EES - Istzustand und zukünftige Entwicklung/Projekte N2 - Der Vortrag stellt potentielle sicherheitstechnische Fragestellungen beim weiterten Ausbau der stationären elektrischen Energiespeicher (EES) in Deutschland dar. Darüber hinaus werden aktuelle Aktivitäten und Projekte der BAM mit Bezug zur Sicherheit von Lithiumbatterien und stationären elektrischen Energiespeichern vorstellt. T2 - Fachgespräch „Stationäre elektr. Energiespeicher (EES) und Anlagensicherheit“ CY - Online meeting DA - 29.01.2021 KW - Stationäre Energiespeicher KW - Elektrische Energiespeicher KW - EES KW - Auswirkungsbetrachtungen PY - 2021 AN - OPUS4-52116 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Risk management and consequence control in hydrogen transport - volume dependent pressure limitation as a scientific approach for consequence control N2 - With technological development, the transport units for compressed gases are becoming larger and their number is increasing. Simultaneously, the filling pressure for hydrogen in transport has increased far beyond the 200 bar, which has been the common European standard for decades. In total, this increases the potential consequences of an incident, which needs to get limited for ensuring acceptance in current practice with pressure vessels from large serial production. Consequently, the measures for new developments of extremely large and highly pressurised pressure vessels should meet a risk based higher level of requirements. For this purpose, the so-called pressure-volume product was proposed as a safety related criteria to the relevant regulatory bodies in 2020. The approach was accepted, and a working group was set up at the United Nations for developing a broadly accepted limitation of today's established pressure vessels compared to future units with even more gas content. The path to the finally decided limit value of 1.5 million bar litres is presented here for hydrogen with its individual steps: ‘Boundary between major accident and disaster’, ‘The effect of pressure waves on the human body’, ‘The propagation of pressure waves’, ‘The reference value for population density’ and ‘Impact of pressure waves’. This result of the UN working group has been accepted in December 2023 and will lead to a binding limitation of the pressure volume product for the so called pressure receptacles by 2027. The work on units larger than this pV-limit is going on at ISO level. T2 - 11th International Conference on Hydrogen Safety ICHS 2025 CY - Seoul, South Korea DA - 22.09.2025 KW - Safety KW - Hydrogen transport KW - Major accident KW - Pressure wave KW - Population density KW - Science with impact PY - 2025 AN - OPUS4-64198 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kröll, Mirco T1 - Harmonising Tribotests of Polymers in Hydrogen N2 - This talk harmonised methods to investigate friction and wear of commercial and experimental polymer compounds in hydrogen using several tribometers. T2 - Surface Ventures - Symposium on Hydrogen Tribology CY - Online meeting DA - 31.07.2025 KW - Hydrogen KW - Polymers KW - Tribometer KW - Wear KW - Coefficient of Friction KW - Interlaboratory comparison KW - Comparability KW - Harmonisation KW - Standardisation KW - Tribology KW - Oil-coupled compounds KW - FAIR data KW - Database KW - i-TRIBOMAT PY - 2025 AN - OPUS4-63838 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Camplese, Davide T1 - Safety assessment of MLI super-insulation systems for cryogenic liquid-hydrogen tanks in fire scenarios N2 - In the context of green energy transition, cryogenic tanks featuring MLI systems are emerging as a leading solution to store hydrogen in heavy-duty vehicles. However, the integrity of such tanks can be jeopardized by fire. In such a scenario, MLI materials degradation can occur, leaving the tank unprotected from the fire heat flux, with consequent rapid pressurization and a high risk of failure. This study presents an assessment of aluminum-based MLI for liquid hydrogen cryogenic tanks under fire exposure based on the estimation of the time to mechanical failure of the equipment. This is calculated through an innovative model that simulates the thermomechanical response of the tank, including the MLI thermal degradation and the pressure-relief valve (PRV) operation. The application to several case studies that consider a typical LH2 tank featuring a wide range of MLI configurations demonstrated the likelihood of failure in case of exposure to a hydrocarbon pool fire, providing also comprehensive insights into the impact of the insulation characteristics and operating conditions on the time to failure. T2 - 18th EFCE International Symposium on Loss Prevention and Safety Promotion in the Process Industries CY - Bologna, Italy DA - 08.06.2025 KW - LH2 KW - Insulation KW - Tanks KW - Fire KW - LNG PY - 2025 AN - OPUS4-63427 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Overview of Hydrogen Safety and remaining challenges N2 - Die Konrad-Adenauer-Stiftung und die Delegation der Deutschen Wirtschaft in Nigeria führt eine "Nigeria Hydrogen Future Webinar Series" durch. Die vierte Veranstaltung wurde unter dem Titel "Safe and Sustainable Hydrogen Production in Nigeria" durchgeführt. Die BAM bzw. das Kompetenzzentrum H2Safety@BAM wurde eingeladen, einen Übersichtsvortrag zur Wasserstoffsicherheit und zukünftigen Herausforderungen mit Blick auf sicherheitstechnische Fragestellungen zu halten. Der Vortrag bildete neben zwei weiteren Vorträgen der Kern des Webinbars. N2 - The Konrad Adenauer Foundation and the Delegation of German Business in Nigeria is conducting a "Nigeria Hydrogen Future Webinar Series". The fourth event was held under the title "Safe and Sustainable Hydrogen Production in Nigeria". BAM respectively the Competence Centre H2Safety@BAM was invited to present an overview lecture on hydrogen safety and future challenges with regard to safety-related issues. The lecture formed the core of the webinbar along with two other presentations. T2 - 4th Nigeria Hydrogen Future Webinar Series CY - Online meeting DA - 27.07.2022 KW - H2Safety@BAM KW - Safety challenges KW - Hydrogen safety PY - 2022 AN - OPUS4-55393 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nattuveettil, Keerthana A1 - Brunner, Nanine A1 - Tiebe, Carlo A1 - Melzer, Michael A1 - Johann, Sergej A1 - Neumann, Patrick P. A1 - Bartholmai, Matthias T1 - Einsatz von Sensortechnologien an einer Wasserstofftankstelle als Beitrag zur digitalen Qualitätsinfrastruktur T1 - Use of sensor technologies at hydrogen test platform as a part of QI Digital N2 - Die Optimierung und Validierung des digitalen Wasserstofftankstellenmanagements mit Sensortechnologien ist das übergeordnete Ziel des Teilprojekts Digitale Qualitätsinfrastruktur mit Sensortechnologien (QIST) am Use Case H2, im Rahmen der digitalen Qualitätsinfrastruktur (QI digital[1]). Hierfür sollen u.a. Sensornetzwerke mit digital-gestützten Auswertungsstrategien intelligent gestaltet werden (Stichwort KI bzw. digitaler Zwilling). Verschiedene, sich ergänzende Sensoren, Systemkomponenten und KI-Methoden stehen als Bausteine intelligenter Sensorsysteme zur Verfügung, mit dem Zweck, die physikalischen und chemischen Parameter an und in Anlagen umfassend und effizient zu überwachen sowie Fehlfunktionen zuverlässig zu detektieren und zu interpretieren, Abbildung 1. Konkrete Arbeitsschritte sind, nach dem Aufbau der Versuchsplattform „Wasserstofftankstelle“, die Instrumentierung von Sensorik und deren digitale Integration in das Tankstellenmanagementsystem sowie die Validierung im Realbetrieb. Die somit erzielten Messergebisse sowie die Messunsicherheiten, Historien und Verfahren werden in digitaler Form aufbereitet, gespeichert und fortlaufend in die KI-basierte Datenauswertung einbezogen, inkl. der Anbindung an die metrologische Rückführungskette. Ziele sind: • Einführung eines neuen messtechnischen Ansatzes und eines digitalen Zwillings für den Anwendungsfall "Wasserstofftankstelle" auf Basis der H2-Sensorik sowie der Zustandsgrößen Druck und Temperatur • Qualitätssicherung durch Applikationen zuverlässiger Gassensorik, Manometer und Thermometer sowie KI-Methoden zur Prozesskontrolle und Detektion von Fehlfunktionen • Nutzung von digitalen Kalibrierscheinen (DCCs) insbesondere für die Messgröße Temperatur zur Realisierung der metrologischen Rückführung in einer digitalen Qualitätsinfrastruktur T2 - Sensorik für die Digitalisierung chemischer Produktionsanlagen CY - Frankfurt a. M., Germany DA - 13.06.2022 KW - QI Digital KW - H2Safety@BAM KW - Wasserstoff KW - Hydrogen KW - Sensorik KW - Digitalisierung KW - Digitalisation PY - 2022 AN - OPUS4-55399 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Effect of temperature on the friction behaviour of rubber materials in hydrogen N2 - Safety and reliability are the major challenges to face for the development and acceptance of hydrogen technology. It is therefore crucial to study deeply material compatibility, in particular for tribological components that are directly in contact with hydrogen. Some of the most critical parts are sealing components that face high risk of damage due variation of pressure, temperature and mechanical stress. In this study, the friction and wear behaviour of several rubber materials was evaluated in hydrogen environment at ambient and low temperature. Tests were performed against 316L disks in a reciprocation motion. Results reveal that the hydrogen affects the friction and wear behaviour of most materials. The friction mechanism is dominated by deformation for most rubber materials at ambient temperature while sliding occurs at low temperature due to the increased hardness of the rubbers. T2 - Polytrib 2024 CY - Portorož, Slovenia DA - 03.10.2024 KW - Reciprocating sliding KW - Rubber materials KW - Hydrogen KW - Low temperature PY - 2024 AN - OPUS4-62019 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Wasserstoff - Energieträger der Zukunft N2 - Im Rahmen des internationalen Wissenschaftsfestivals, der Berlin Science Week 2021, hat die BAM in einem Beitrag das Kompetenzzentrum H2Safety@BAM, dessen Vision und die vier wissenschaftlichen Kompetenzfelder sowie den dort bearbeiteten Themen bzw. Projekten vorgestellt. T2 - Berlin Science Week 2021 CY - Berlin, Germany DA - 01.11.2021 KW - H2Safety@BAM KW - Materialeignung und -kompatibilität KW - Bauteilprüfung, -sicherheit und -zertifizierung KW - Prozess- und Anlagensicherheit KW - Sensorik, Analytik und Referenzmaterialien KW - Sicherheit KW - Vertrauen in Wasserstofftechnologien PY - 2021 AN - OPUS4-55136 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -