TY - CONF A1 - Winckelmann, Alexander T1 - Investigation of degradation of the aluminum current collector in lithium-ion batteries by GD-OES N2 - Lithium-ion batteries (LIBs) are one technology to overcome the challenges of climate and energy crisis. They are widely used in electric vehicles, consumer electronics, or as storage for renewable energy sources. However, despite innovations in batteries' components like cathode and anode materials, separators, and electrolytes, the aging mechanism related to metallic aluminum current collector degradation causes a significant drop in their performance and prevents the durable use of LIBs. Glow-discharge optical emission spectroscopy (GD-OES) is a powerful method for depth-profiling of batteries' electrode materials. This work investigates aging-induced aluminum deposition on commercial lithium cobalt oxide (LCO) batteries' cathodes. The results illustrate the depth-resolved elemental distribution from the cathode surface to the current collector. An accumulation of aluminum is found on the cathode surface by GD-OES, consistent with results from energy-dispersive X-ray spectroscopy (EDX) combined with focused ion beam (FIB) cutting. In comparison to FIB-EDX, GD-OES allows a fast and manageable depth-profiling. Results from different positions on an aged cathode indicate an inhomogeneous aluminum film growth on the surface. The conclusions from these experiments can lead to a better understanding of the degradation of the aluminum current collector, thus leading to higher lifetimes of LIBs. T2 - Empa Group Meeting CY - Dübendorf, Switzerland DA - 22.11.2022 KW - Lithium Ion Batteries KW - GD-OES KW - FIB KW - SEM KW - EDX PY - 2022 AN - OPUS4-56584 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böttcher, Nils T1 - A Journey From Formula Student to Research at BAM N2 - In this presentation, the battery and cell test center of BAM is introduced to the Berlin Motion Lab. Points of intersection are identified, and interested students are familiarized with BAM’s research priorities in the field of batteries. The aim is to foster interaction and to inspire young researchers to engage with technologically relevant topics. T2 - Berlin Deep Tech Nexus Meetup CY - Berlin, Germany DA - 26.02.2025 KW - Battery safety KW - BAM-academy KW - Qualification programme for PhD students at BAM KW - Advanced (battery) safety topics PY - 2025 AN - OPUS4-65079 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Long, Lijia A1 - Anh Mai, Q. A1 - Morato, P. G. A1 - Dalsgaard Sorensen, J. A1 - Thöns, Sebastian T1 - Information value-based optimization of structural and environmental monitoring for offshore wind turbines support structures N2 - The use of load and structural performance measurement information is vital for efficient structural integrity management and for the cost of energy production with Offshore Wind Turbines (OWTs). OWTs are dynamically sensitive structures subject to an interaction with a control unit exposed to repeated cyclic wind and wave loads causing deterioration and fatigue. This study focuses on the quantification of the value of structural and environmental information on the integrity management of OWT structures, with the focus on fatigue of welded joints. By utilizing decision analysis, structural reliability methods, measurement data, as well as the cost-benefit models, a Value of Information (VoI) analysis can be performed to quantify the most beneficial measurement strategy. The VoI assessment is demonstrated for the integrity management of a butt welded joint of a monopile support structure for a 3 MW OWT with a hub height of approximately 71m. The conditional value of three-year measured oceanographic information and one-year strain monitoring information is quantified posteriori in conjunction with an inspection and repair planning. This paper provides insights on how much benefits can be achieved through structural and environmental information, with practical relevance on reliability-based maintenance of OWT structures. KW - Structural health monitoring KW - Offshore wind turbine KW - Monopile support structure KW - Value of information KW - Weld fatigue KW - Decision tree KW - Dynamic Bayesian Network PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-514098 DO - https://doi.org/10.1016/j.renene.2020.06.038 VL - 10 IS - 159 SP - 1036 EP - 1046 PB - Elsevier Ltd. AN - OPUS4-51409 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Thöns, Sebastian A1 - Faber, M. H. A1 - Rücker, Werner T1 - Fatigue and serviceability limit state model basis for assessment of offshore wind energy converters N2 - This paper develops the models for the structural performance of the loading and probabilistic characterization for the fatigue and the serviceability limit states for the support structure of offshore wind energy converters. These models and a sensitivity study are part of a risk based assessment and monitoring framework and will be applied for establishing the 'as designed and constructed' reliability as prior information for the assessment and the design of monitoring systems. The constitutive physical equations are introduced in combination with the fatigue and serviceability limit state requirements as the starting point for the development of the structural performance and loading models. With these models introduced in detail, several modeling aspects for both limit states are analyzed. This includes analyses of the influence on the hot spot stresses by applying a contact formulation for the pile guide brace connection and the application of a finite element formulation using solid elements. Further, the comparison of the natural frequencies of a discrete rotor model with a continuous rotor model is documented. To account for uncertainties associated with the structural and loading models, a probabilistic model is derived on the basis of literature review and measurement data from a prototype Multibrid M5000 support structure. The sensitivity study is based on the calculation of a nonlinear coefficient of correlation in conjunction with predetermined designs of experiments. This is conducted by a systematic analysis of the influence of the random variables on limit state responses and hence on the structural reliability. Integrating the analyses and sensitivity studies of the fatigue and serviceability limit state models developed in this paper as well as the ultimate limit state models in Thöns et al. ('Ultimate Limit State Model Basis for Assessment of Offshore Wind Energy Converters,' ASME J. Offshore Mech. Arct. Eng.), the model basis for the assessment is completed. The process of establishing and analyzing such a model basis contributes to a detailed understanding of the deterministic and probabilistic characteristics of the structure and provides valuable insights in regard to the significance of available data. KW - Fatigue KW - Finite element analysis KW - Rotors KW - Wind power KW - Model basis KW - Offshore wind KW - Support structure KW - Sensitivity KW - Serviceability PY - 2012 DO - https://doi.org/10.1115/1.4004514 SN - 0892-7219 VL - 134 IS - 3 SP - 1 EP - 10 PB - American Society of Mechanical Engineers (ASME) CY - New York, NY AN - OPUS4-26437 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kunkel, Benny A1 - Seeburg, Dominik A1 - Kabelitz, Anke A1 - Witte, Steffen A1 - Gutmann, Torsten A1 - Breitzke, Hergen A1 - Buntkowsky, Gerd A1 - de Oliveira Guilherme Buzanich, Ana A1 - Wohlrab, Sebastian T1 - Highly productive V/Zn-SiO2 catalysts for the selective oxidation of methane N2 - The production of formaldehyde on industrial scale requires huge amounts of energy due to the involvement of reforming processes in combination with the demand in the megaton scale. Hence, a direct route for the transformation of (bio)methane to formaldehyde would decrease costs and puts less pressure on the environment. Herein, we report on the use of zinc modified silicas as possible support materials for vanadium catalysts and the resulting consequences for the performance in the selective oxidation of methane to formaldehyde. After optimization of the Zn content and reaction conditions, a remarkably high space-time yield of 12.4 kgCH2O⋅kgcat − 1 ⋅h− 1 was achieved. As a result of the extensive characterization by means of UV–vis, Raman, XANES and NMR spectroscopy it was found that vanadium is in the vicinity of highly dispersed zinc atoms which promote the formation of active vanadium species as supposed by theoretical calculations. This work presents a further step of catalyst development towards direct industrial methane conversion which may help to overcome current limitations in the future. KW - Catalysis KW - XANES KW - Selective oxidation PY - 2024 DO - https://doi.org/10.1016/j.cattod.2024.114643 SN - 0920-5861 VL - 432 SP - 1 EP - 13 PB - Elsevier B.V. AN - OPUS4-60137 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Tribologische Untersuchungen unter GH2 und LH2-Bedingungen N2 - In diesem Beitrag werden Untersuchungen an Polymerwerkstoffen auf ihre Eignung für Reibsysteme in gasförmigem und flüssigem Wasserstoff vorgestellt. Dabei wird der Einfluss der Wasserstoffumgebung in Bezug auf die Materialzusammensetzung diskutiert. Weiterhin zeigen die Experimente in LH2 einen deutlichen Einfluss der Temperatur, der jedoch bei den verschiedenen Polymerverbundwerkstoffen unterschiedlich stark ausgeprägt ist. T2 - DKV Tagung CY - Hannover, Germany DA - 23.11.2023 KW - Polymerwerkstoffe KW - Reibung KW - Verschleiß KW - Gasförmiger Wasserstoff KW - Flüssiger Wasserstoff PY - 2023 AN - OPUS4-61963 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Toward sustainable and hydrogen compatible sealing materials N2 - Materialien auf PTFE-Basis werden in der Regel als Kolbenringe in Hochdruck- und/oder kryogenem Wasserstoff verwendet. In diesem Projekt werden neu formulierte und nachhaltigere Polymerwerkstoffe mit herkömmlichen Materialien verglichen. Auf Grundlage der tribologischen Ergebnisse werden vielversprechende Kandidaten zusammen mit Reibungsmechanismen sowohl bei Hochdruck- als auch bei Niedrigtemperatur-Wasserstoff vorgeschlagen. T2 - 66. Tribologie-Fachtagung 2025 CY - Wernigerode, Germany DA - 29.09.2025 KW - Wasserstoff KW - Reibung KW - Verschleiß KW - Kolbenring KW - Dynamische Dichtung PY - 2025 AN - OPUS4-64313 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Fretting wear of elastomer materials in hydrogen N2 - This paper presents an experimental study on the fretting wear behavior of two types of cross-linked hydrogenated acrylonitrile butadiene rubbers against 316L steel ball in hydrogen environment. Furthermore, aging experiments were conducted for 7 days under static conditions in 100 MPa hydrogen. The influences of hydrogen pressure as well as the aging exposure on the fretting behavior are discussed by means of surface analyses and well as material properties. T2 - WHEC-2022, 23rd World Hydrogen Energy Conference CY - Istanbul, Turkey DA - 26.06.2022 KW - Rubbers KW - Hydrogen KW - Fretting PY - 2022 AN - OPUS4-62086 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - Polymer tribology in cryogenic hydrogen N2 - In this presentation, an overview of polymer tribology in cryogenic hydrogen is given along comparison with other environments. T2 - Hydrogenius Symposium 2024 CY - Kyushu University Ito Campus, Japan DA - 12.09.2024 KW - Hydrogen KW - Friction KW - Wear KW - Polymer materials KW - Cryogenic PY - 2024 AN - OPUS4-61426 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. A1 - Hajhariri, Aliasghar A1 - Sklorz, Christian A1 - Kriegsmann, Andreas A1 - Müller, Karsten T1 - A modular concept for protection against debris flight - Design, properties and usage N2 - With advances in technological development, stationary and mobile storage units for compressed hydrogen are becoming larger and larger. Their number is also increasing. At the same time, their design has evolved from steel and aluminium to pressure vessels made of composite materials. For safety reasons the design approval of those composite cylinders requires fire engulfment tests, which are mainly organised as open-air tests always needs dedicated protection measures. Under some conditions those protections measures even reduce the effort for organisational safety measures if e.g. the emission of splinters can get totally prevented. Another aspect is the improved reproducibility of fire tests by reducing the influence of wind. Between 2017 and 2019, BAM developed a stackable protective frame made of steel to safely capture splinters for the safe execution of high-energy impact tests. However, this frame was not flexible enough for the follow-up project, which led to a completely new protection concept for (potentially) destructive tests on gas-filled pressure vessels. This concept is based on very robust building blocks made from welded steel. Despite their considerable weight of around 500 kg p.p., they can be combined and stacked very easily like ‘Lego bricks’. The presentation will show the flexibility of the concept, some results of tests on the robustness against pressure waves and the effectiveness in wind attenuation. Finally, the interaction with a new, also modular burner concept for localised fires and full engulfment fires will be presented. T2 - 11th International conference on hydrogen safety (ICHS 2025) CY - Seoul, Republic of Korea DA - 22.09.2025 KW - Splinter protection KW - Pressure vessel testing KW - Fire engulfment KW - Destructive tests KW - Rupture KW - Gaseous tests KW - Pressure wave KW - Test equipment KW - Precaution measures PY - 2025 SN - 979-1-2243-0274-2 VL - 2025 SP - 1428 EP - 1439 AN - OPUS4-65100 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Welcome to BAM and the Competence Centre H2Safety@BAM N2 - The presentation starts with general slides on BAM, its mission and focus areas. It provides the fields of activity in the focus area “Energy” and explains the structure of the competence Centre and its focus on building trust in hydrogen. The next part shows the H2Safety@BAM’s Products“ in a nutshell and explains the main items with deep dives on the Living Lab “Hydrogen Networks”, the Living Lab „Hydrogen Refuelling Station“, on Reference Materials and Procedures, Storage of Liquid Hydrogen, Storage Systems for Compressed Gases and Material Compatibility. T2 - Information Tour at the Invitation of the Federal Foreign Office The Hydrogen Economy in Germany CY - Berlin, Germany DA - 05.11.2025 KW - Living Lab “Hydrogen Networks” KW - Living Lab „Hydrogen Refueling Station“ KW - Reference Materials and Procedures KW - Storage of Liquid Hydrogen KW - Storage Systems for Compressed Gases KW - Material Compatibility PY - 2025 AN - OPUS4-65101 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sterr, Andrea A1 - Schwarz, Irina T1 - Valorization of Carbon Dioxide by Electrocatalytic Reduction Coupled to Acetogens via Multiple Electron Carriers (Ecat-Acetogens II) N2 - A Bioelectrochemical approach for reducing CO2 to fuels or value-added chemicals allows overcoming the limitations of a pure biochemical or electrochemical approach. A Bioelectrochemical system (BES) for this application has been developed in cooperation with TUM in the first project phase. BAM's contribution to the research focuses on the electrochemical side of the setup, mainly on the development of a suitable CO2RR catalyst for reducing CO2 to CO, which is then consumed by actogenic bacteria to produce further products. Single-metal-atom catalysts in a nitrogen-doped carbon matrix (M-N-Cs) are a promising, sustainable alternative to expensive rare-metal catalysts like Ag and Au. In this work, the first-generation catalyst, a ZIF-8-based Co-N-C is compared to a Mg salt mix templated Ni-N-C. In the new catalysts, the activity for CO2RR as well as the stability during BES operation could be enhanced. T2 - E-Biocat Statusupdate 2025 CY - Karlsruhe, Germany DA - 01.04.2025 KW - CO2RR KW - M-N-Cs KW - Bioelectrochemical System PY - 2025 AN - OPUS4-65143 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - DE-JP Hydrogen Safety Cooperation - Contribution of H2Safety@BAM N2 - The presentation starts with general slides on BAM, its location, mission, tasks and focus areas. It provides the fields of activity in the focus area “Energy” and explains the structure of the competence Centre and its focus on building trust in hydrogen. The test sides at TTS on hydrogen are explained in combination with the H2Safety@BAM’s products in a nutshell. Then the major H2-applications of H2Safety@BAM are explained by deep dives on the Living Lab “Hydrogen Networks”, the Living Lab „Hydrogen Refuelling Station“, on Explosion Protection, on Reference Materials and Procedures, on Material Compatibility, on Storage Systems for Compressed Gases and Storage of Liquid Hydrogen as well as on the Training and Further Education. The presentation ends with an overview about our international work on H2Safe-Collaboration. T2 - KICK-OFF WORKSHOP: JAPANESE-GERMAN COOPERATION ON H2 SAFETY CY - Online meeting DA - 15.12.2025 KW - Living Lab KW - Hydrogen Networks KW - Hydrogen Refuelling Station KW - Explosion Protection KW - Material Compatibility KW - Liquid Hydrogen KW - Compressed Gases PY - 2025 AN - OPUS4-65151 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scharf-Wildenhain, R. T1 - Influence of build up height on residual stresses in additive repair and modification using DED Arc N2 - Directed Energy Deposition (DED)-Arc is suitable for the hybrid additive manufacturing, modification and repair of large metal components with high deposition rates. Residual stresses and distortion are of central importance when characterizing the manufactured components and the sensitive transition area between AM component and semi-finished product. Residual stresses caused by the thermal cycles during the manufacturing process can impair the mechanical properties of the manufactured parts and can lead component failure. Therefore, understanding and controlling residual stresses, especially when combining different base and filler materials, is critical to improving the quality and efficiency of the hybrid DED-Arc process. This article deals with the influence of the build-up height on the residual stress distribution of additively manufactured components with a selected base and filler material combination. Using a robot-assisted DEDsystem and a controlled short arc, systematic step cancellation tests were carried out at a selected working temperature (200 C°) and heat input (600 kJ/m). In a 5-stage termination experiment, straight walls were produced using a one bead per layer strategy and selected increasing component heights between 15 mm and 300 mm. The influence of the build height on the longitudinal residual stress in the process direction was analyzed and discussed. All experiments showed a comparable stress distribution in the area of the substrate plate up to the heat-affected zone (HAZ) and the transition zone, regardless of the buliding height. However, the height showed a significant influence on the of residual stress distribution of the deposited AM-component. High positive stress gradients with a maximum range between 300 MPa to 400 MPa were always found in the last approx. 18 component layers (upper 40 mm), which can be explained by the shrinkage of the nonheat- treated top layer. Underlying layers, where present, showed a homogeneous residual stress distribution characterized by low compressive stresses. This can be explained by the process related tempering during the deposition of the upper layers. A constant boundary layer number was determined for all specimens. Once this number was exceeded, the distribution of residual stresses no longer changed, but merely shifted with the increasing height of the component in the direction of build-up. These correlations contribute to the understanding of residual stress development with increasing structure height. This study is part of a running research project on the properties of hybrid additive components and processes. It aims the stress optimized hybrid additive manufacturing of high-strength components and the necessary recommendations for application. T2 - 78th IIW Annual Assembly and International Conference on Welding and Joining CY - Genoa, Italy DA - 22.06.2025 KW - DED-Arc KW - Additive manufacturing KW - Residual stress PY - 2025 AN - OPUS4-65192 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ghaznavi, Ali T1 - Machine Learning Approach for Robust Acoustic Emission-Based Damage Classification in Pressure Vessels N2 - Accurate damage classification of Composite Pressure Vessels (CPVs) is crucial for understanding failure behaviour of hydrogen storage systems. Acoustic Emission (AE) monitoring is a non-destructive testing technique capable of detecting signals from different failure mechanisms such as fiber breakage and matrix cracking, supporting durability assessment of CPVs. Therefore, the main objective of this study is to combine AE and advanced deep learning techniques to develop a robust framework for automatic and accurate identification and classification of damage mechanisms across various CPVs. The evolutionary Genetic Algorithms (GA) was used for feature selection, followed by unsupervised clustering to generate automatic labels for model training. Two different FCNN and CNN-LSTM architectures were used to train individual models based on different AE datasets. Later, Adaptive Transfer Learning (ATL) and Meta Ensemble Learning (MEL) techniques were applied to handle data variability and train predictive generalized model over varied AE datasets. The ATL fine-tunes a pre-trained models to leverage their knowledge, while MEL uses pre-trained models' predictions as meta features to train a meta model. Experimental results demonstrate that while both generalized ATL and MEL trained models perform well across different AE datasets, the MEL framework outperforms ATL method in terms of evaluation metrics. The Mean-Accuracy score reaches 0.9026, and 0.9900 for ATL, and MEL, respectively. The most accurate multi-class classification results was achieved using MEL method in terms of the Mean-Accuracy and Recall metrics. The proposed framework provides a scalable, adaptive approach for automated damage classification using AE signals across diverse CPVs in real-world settings. T2 - BAM Colloquium Abteilung 3 CY - Berlin, Germany DA - 14.10.2025 KW - Acoustic Emission KW - Machine Learning KW - Sequential Neural Network KW - Deep Learning KW - Deep Neural Network PY - 2025 AN - OPUS4-65184 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröpfer, Dirk T1 - Wear resistance of modified Ni based claddings in relation to the resulting machinability via ultrasonic-assisted milling N2 - In the field of plastics processing, extruder screws are subjected to significant wear stresses. The extruder screw is the main wear component in those production machines and is usually coated with intermetallic wear protection alloys composed of Ni-based alloys, specifically Colmonoy C56 PTA (NiMoCrSi). There is a growing demand for providing an economic machinability of these alloys to achieve defined contours with a sufficient surface integrity. Recent investigations exhibit promising results applying ultrasonic milling for such hard-to-cut materials. The Colmonoy C56 is modified by various alloying additions Ti, Nb, Mo, Hf, and Al, and then cladded on a steel S355 via Plasma Transferred Arc process. The effect of alloying additions on the microstructure is analyzed regarding their resistance to abrasive and adhesive wear. With Miller test ASTM G75 the influence of alloying elements on resistance to abrasive wear for two abrasive materials is investigated (high-grade corundum F220 and quartz powder). The wear loss is not increased for additions of Nb and Ti compared to the base material C56. Modifications with Hf or Al reduces the resistance to abrasive wear and significantly increases material loss. The extruder screw is also subject to adhesive wear, which can be quantified by means of the pin-roll test. It is demonstrated that the addition of Hf, for example, contributes to a reduction in wear loss. Aim of the investigations is to find suitable modifications for the wear claddings of C56 for a sufficient machineability, without compemising the wear resistant. The machinability is considerably affected by the alloy additions, and is determined using ultrasonic-assisted milling. The addition of hafnium reduces machinability, i.e. significantly increases cutting forces. The incorporation of Nb exhibits a significant reduction of cutting forces, and results in reduced tool wear and an enhanced of surface integrity (roughness, density of defects, residual stresses). T2 - Wear of Materials 2025 CY - Sitges, Spain DA - 13.04.2025 KW - Abrasive wear KW - Adhesive wear KW - Colmonoy C56 KW - PTA welding KW - Service life and efficiency KW - Substitution of critical raw materials KW - Surface integrity KW - Ultrasonic-assisted milling process PY - 2025 AN - OPUS4-65189 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Drexler, A.-K. A1 - Konert, Florian A1 - Nietzke, Jonathan A1 - Hodžić, E. A1 - Pastore, S. A1 - Domitner, J. A1 - Rhode, Michael A1 - Sommitsch, C. A1 - Böllinghaus, Thomas T1 - Effect of Tensile Loading and Temperature on the Hydrogen Solubility of Steels at High Gas Pressure N2 - The hydrogen solubility in ferritic and martensitic steels is affected by hydrostatic stress, pressure, and temperature. In general, compressive stresses decrease but tensile stresses increase the hydrogen solubility. This important aspect must be considered when qualifying materials for high‐pressure hydrogen applications (e.g., for pipelines or tanks) by using autoclave systems. In this work, a pressure equivalent for compensating the effect of compressive stresses on the hydrogen solubility inside of closed autoclaves is proposed to achieve solubilities that are equivalent to those in pipelines and tanks subjected to tensile stresses. Moreover, it is shown that the temperature effect becomes critical at low temperatures (e.g., under cryogenic conditions for storing liquid hydrogen). Trapping of hydrogen in the microstructure can increase the hydrogen solubility with decreasing temperature, having a solubility minimum at about room temperature. To demonstrate this effect, the generalized law of the hydrogen solubility is parameterized for different steels using measured contents of gaseous hydrogen. The constant parameter sets are verified and critically discussed with respect to the high‐pressure hydrogen experiments. KW - Hydrogen KW - Solubility KW - Temperature KW - Tensile loading KW - Analytical calculation PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-586701 DO - https://doi.org/10.1002/srin.202300493 SN - 1611-3683 SP - 1 EP - 9 PB - Wiley AN - OPUS4-58670 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Sobol, Oded T1 - Hydrogen assisted cracking and transport studied by ToF-SIMS and data fusion with HR-SEM N2 - For almost 150 years it is known that hydrogen has a deleterious effect on the mechanical properties of metallic components. Nowadays, the problem of hydrogen assisted degradation is highly relevant in energy related fields due to the massive use of steel as a structural component in these applications and its sensitivity to hydrogen. Since the discovery of hydrogen assisted cracking (HAC), researchers studied intensively and suggested possible explanations and mechanisms in order to define how hydrogen is affecting the material. In general, it is considered that hydrogen changes the mechanical properties more in terms of ductility (deformation capacities) than in strength (load capacities). Hydrogen concentration is one of three crucial factors in the degradation process, together with the microstructure of the material and the internal/external mechanical load. The relatively high concentration of hydrogen resulting in this loss of ductility can originate during production or before service (e.g. welding processes) and during service (i.e. catholically protected systems to eliminate corrosion processes in sour environments). In parallel to the theoretical work, tremendous efforts were, and are still, invested in searching for a proper method to elucidate, map and quantify the hydrogen in the microstructure, which is the basis for this work. For steels, the focus is mainly on the observations of diffusion processes and the interaction of hydrogen with the microstructure in regions with high local stresses/strains (for example around evolving cracks). The challenge for reaching this goal arises from the fact that accurate indication of hydrogen by means of position, unlike heavier atoms, can be made only by mass spectrometry or by interaction with another element (e.g. silver decoration, special coating and resonant nuclear reaction by nitrogen). In addition to this, the difficulty recording the hydrogen behavior while it rapidly diffuses through the material, leaving only the unpredicted failure, should be taken into account. Although using powerful characterization methods, models and computational simulations, the key to defining the mechanisms behind HAC is still under debate and not fully understood. The relationship between material and hydrogen is determined by three factors, i.e., the material structure and microstructure – determining the physical properties, the mechanical load applied on the material and the hydrogen concentration. It is well known that in order to have a complete definition of HAC these three factors must be examined locally with the minimal scale and the maximal resolution reachable. The major gap is the lack in such a characterization method or a technique by which one has the ability to detect and observe the hydrogen in the metallic microstructure. The commonly used techniques nowadays are capable of characterization of the microstructure without the ability to observe the hydrogen distribution. Global hydrogen concentration and localized hydrogen observation are possible by some techniques which are incapable of indicating a change in the structure or microstructure therefore a comprehensive overview can be gained only by combining several methods. In the presented research, secondary ion mass spectrometry (SIMS) was adopted as the main tool to detect and locally map the hydrogen distribution in two types of duplex stainless steel grades: EN 1.4462 (standard 2205 duplex stainless steel) and EN 1.4162 (2101 lean duplex stainless steel). The term duplex stainless steel (DSS) refers to the austenitic-ferritic microstructure of the steel where the combination of physical and mechanical properties of the two phases is achieved. The DSS was selected as a case study for this work due to the wide use of this grade in many energy and the lack of knowledge on hydrogen behavior in two-phase containing microstructures. ToFSIMS was exploited in-situ and ex-situ in three experimental approaches during or following an electrochemical charging procedure. This type of hydrogen charging was selected as it simulated a procedure of cathodic protection of most sub-water oil and gas extraction and delivery systems. The experimental procedures were: 1. Ex-situ charging followed by ToF-SIMS imaging for basic understanding of hydrogen distribution. 2. Ex-situ charging followed by in-situ mechanical loading to obtain information on hydrogen behavior around a propagating crack. 3. In-situ permeation of hydrogen through a steel membrane inside the ToF-SIMS to obtain information on diffusion behavior of hydrogen in a two-phase microstructure. The comprehensive view of the effect of hydrogen on steel was gained by using supplementary methods, such as high resolution scanning electron microscopy (HR-SEM), focused ion beam (FIB) and electron back-scattered diffraction (EBSD). The state of the art in this work lies in applying both: in-situ experimental approaches and data treatment of the ToF-SIMS raw data. The data treatment includes the combination of data from several sources (data fusion). The results for the ex-situ charging followed by static sample imaging and data fusion showed that when the analyzed surface is directly exposed to the electrolyte the degradation is pronounced differently in the ferrite, austenite and interface. The degradation mechanisms in the ferrite and austenite were reflected by the formation of cracks on the surface of both, where a high concentration of hydrogen was obtained. This result supports the assumption that hydrogen is attracted to highly deformed regions. The advantage of using in-situ charging/permeation in comparison to ex-situ charging is that the effect of hydrogen on the ferrite and austenite phases when the hydrogen is evolving from within the microstructure is realized, in comparison to when the analyzed surface is initially exposed directly to the electrolyte. In both experiments the ferrite was observed as a fast diffusion path for the hydrogen. The faster diffusion of hydrogen through the ferrite is expected due to the higher diffusion coefficient, however, a direct proof for the diffusion sequence in this scale was never shown. Most significant results were achieved by the ‘core’ experiments of this research. These experiments included the design of a novel dynamic mechanical loading device to apply an external load during SIMS imaging of a hydrogen precharged-notched sample. For the first time it was shown that plastic deformation induced by applying a mechanical load is resulting in a redistribution of hydrogen locally around the notch. T3 - BAM Dissertationsreihe - 160 KW - Duplex stainless steels KW - Hydrogen assisted cracking KW - Time-of-Flight secondary ion mass spectrometry KW - Data fusion PY - 2018 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-447331 SN - 1613-4249 VL - 160 SP - I EP - 180 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-44733 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Drexler, A A1 - Konert, Florian A1 - Sobol, Oded A1 - Rhode, Michael A1 - Domitner, J A1 - Sommitsch, C A1 - Böllinghaus, Thomas T1 - Enhanced gaseous hydrogen solubility in ferritic and martensitic steels at low temperatures N2 - Metals that are exposed to high pressure hydrogen gas may undergo detrimental failure by embrittlement. Understanding the mechanisms and driving forces of hydrogen absorption on the surface of metals is crucial for avoiding hydrogen embrittlement. In this study, the effect of stress-enhanced gaseous hydrogen uptake in bulk metals is investigated in detail. For that purpose, a generalized form of Sievert's law is derived from thermodynamic potentials considering the effect of microstructural trapping sites and multiaxial stresses. This new equation is parametrized and verified using experimental data for carbon steels, which were charged under gaseous hydrogen atmosphere at pressures up to 1000 bar. The role of microstructural trapping sites on the parameter identification is critically discussed. KW - Hydrogen KW - Thermodynamic modelling KW - Pressure-dependent solubility KW - Steel KW - Trapping PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-559307 DO - https://doi.org/10.1016/j.ijhydene.2022.09.109 SN - 0360-3199 VL - 47 IS - 93 SP - 39639 EP - 39653 PB - Elsevier Ltd. AN - OPUS4-55930 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Campari, Alessandro A1 - Konert, Florian A1 - Sobol, Oded A1 - Alvaro, Antonio T1 - A comparison of vintage and modern X65 pipeline steel using hollow specimen technique for in-situ hydrogen testing N2 - The transition toward a hydrogen-based economy requires a widespread transport and distribution network, and repurposed natural gas pipelines are a viable option. An assessment of the hydrogen-induced degradation of pipeline steels is needed to inject H2 gas into the existing infrastructure safely. The conservative and standardized method consists of in-situ tensile tests in an autoclave filled with high-pressure hydrogen gas. A proposed alternative method involves using a hollow specimen as containment volume and applying the gas pressure in the inner cavity. This technique has lower costs and shorter test preparation time but is not standardized yet. This study aims to evaluate and compare the tensile properties of API 5L X65 pipeline steel in two states: vintage and modern. The influence of the surface roughness is investigated through parallel tests with drilled and reamed specimens. Hydrogen tests are compared with reference tests in an inert environment. A significant hydrogen-induced decrease in tensile properties is observed, and no significant difference between vintage and modern X65 can be drawn. The reduction in tensile properties is more significant in specimens with higher inner surface roughness. The evaluation of surface conditions appears crucial when assessing the HE susceptibility of hydrogen transport and storage equipment. KW - Hydrogen embrittlement KW - Hollow specimen technique KW - Pipeline steel KW - SSRT PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-603013 DO - https://doi.org/10.1016/j.engfailanal.2024.108530 VL - 163 SP - 1 EP - 15 PB - Elsevier Ltd. AN - OPUS4-60301 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nietzke, Jonathan A1 - Konert, Florian A1 - Poka, Konstantin A1 - Merz, Benjamin A1 - Sobol, Oded A1 - Böllinghaus, Thomas T1 - Comparison of hydrogen effects on additively manufactured and conventional austenitic steels N2 - Hydrogen and its derivatives are promising energy carriers for future renewable energy supplies. Austenitic stainless steels, such as AISI 316L, are commonly used in hydrogen transportation systems. While often thought to be resistant to hydrogen embrittlement, studies have shown that 316L is susceptible under certain conditions. As demand for hydrogen applications grows, additive manufacturing (AM) technologies offer design flexibility and customisation benefits. However, data on AM parts behaviour in hydrogen environments is lacking. This study investigates the influence of hydrogen on mechanical properties using slow strain rate testing (SSRT) on conventional AISI 304L, 316L and AM 316L specimens. The results indicate a greater effect of hydrogen on 304L compared to 316L, with AM 316L showing increased susceptibility. However, the ductility of AM 316L remains comparable to conventional 316L due to its initial ductility. The study provides insights into the performance of conventional and AM austenitic stainless steels in gaseous hydrogen environments. KW - Slow strain rate testing KW - Hollow specimen KW - Hydrogen embrittlement KW - Additive manufacturing KW - Austenitic steel PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-615919 DO - https://doi.org/10.1016/j.engfailanal.2024.109042 SN - 1350-6307 VL - 167 SP - 1 PB - Elsevier B.V. AN - OPUS4-61591 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Grimault de Freitas, Tomás A1 - Konert, Florian A1 - Nietzke, Jonathan A1 - Krzysch, Zephanja A1 - Böllinghaus, Thomas A1 - Michler, Thorsten A1 - Wackermann, Ken A1 - Oesterlin, Heiner A1 - Tlili, Mohamed A1 - Ruchti, Peter A1 - Beitelschmidt, Denise A1 - Elsen-Humberg, Stephan A1 - Koenigs, Timo A1 - Systermans, Thomas A1 - Sobol, Oded T1 - Tensile testing in high-pressure gaseous hydrogen using the hollow specimen method N2 - Metallic materials, predominantly steels, are the most common structural materials in the various components along the hydrogen supply chain. Ensuring their sustainable and safe use in hydrogen technologies is a key factor in the ramp-up of the hydrogen economy. This requires extensive materials qualification, however, most of the accepted; and standardized test methods for determining the influence of gaseous hydrogen on metallic materials describe complex and costly procedures that are only available to a very limited extent worldwide. The hollow specimen technique is a simple, rapid, and economical method designed to overcome the limitations of the current methods for the qualification of metallic materials under high-pressure hydrogen gas. However, this technique is not yet standardized. The TransHyDE-H2Hohlzug project is presented in this article, along with the main steps required to optimize the hollow specimen technique. This includes closing knowledge gaps related to the specimen geometry, surface quality, and gas purity in dedicated working packages, thus contributing to a comprehensive standardization of the technique for tests in high-pressure hydrogen gas. KW - High-pressure Gaseous Hydrogen KW - Hydrogen Embrittlement KW - Tensile Testing KW - Hollow Specimen Technique PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-610557 DO - https://doi.org/10.1557/s43577-024-00776-9 VL - 49 SP - 1 EP - 9 PB - Springer Nature AN - OPUS4-61055 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Konert, Florian A1 - Nietzke, Jonathan A1 - Grimault de Freitas, Tomás A1 - Rhode, Michael A1 - Sobol, Oded A1 - Böllinghaus, Thomas T1 - Investigation of resistance to gaseous hydrogen of a longitudinal weld seam in a X65 pipeline using the hollow specimen technique N2 - The constantly increasing demand for renewable energy sources leads to the necessity of transporting large amounts of hydrogen. Since pipelines enable a cost-effective way for the distribution of gaseous hydrogen, the interaction of hydrogen and the pipeline materials must be carefully investigated as hydrogen can cause a degradation of the mechanical properties under certain conditions. Especially welds, which are assumed to be more susceptible to the degradation enhanced by hydrogen, are of great interest. The aim of this study is to investigate the effect of gaseous hydrogen on the mechanical properties of an X65 pipeline, and the longitudinal submerged arc welding (SAW) welded joint. The tests are conducted using the hollow specimen technique on two types of specimens: one extracted from the base material (BM) and the other extracted as a cross-weld (CW) specimen consisting of BM and weld seam. The specimens are charged in situ under a pressure of 60 bar and tested using slow strain rate (SSR) tensile tests with a nominal strain rate of 10−5 s−1. The properties obtained of specimens tested in hydrogen atmosphere are compared to the properties of comparable specimen in inert argon atmosphere as a reference. The performed tests showed a decrease of the reduction of area (RA) from 72% in inert atmosphere to 52% in hydrogen atmosphere for the CW specimen and a decrease from 73% in inert atmosphere to 51% for the BM. Metallographic analyses showed the crack initiation between fine-grained heat-affected zone (FGHAZ) and BM for the specimens tested in hydrogen atmosphere as well as for the reference specimens. This leads to the conclusion that the location of the crack initiation does not change due to the presence of gaseous hydrogen. KW - Hydrogen KW - Hollow specimen technique KW - Pipeline KW - SSRT KW - Hydrogen embrittlement KW - Cross-weld specimen PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-624658 DO - https://doi.org/10.1007/s40194-025-01953-3 SN - 0043-2288 SN - 1878-6669 VL - 69 IS - 3 SP - 861 EP - 870 PB - Springer CY - Berlin AN - OPUS4-62465 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael T1 - Hydrogen in Welded Microstructures of T24 Steel: Effect on Mechanical Properties and Corresponding Hydrogen Diffusion N2 - Low-alloyed CrMoV steels, such as T24, are widely used for welded components in fossil power stations due to their excellent creep-strength. Spectacular failure cases in the recent years exhibited severe cracking in T24 welds. The results showed that hydrogen-assisted cracking (HAC) occurring up to 200 degree Celsius cannot be excluded. Hence, a basic understanding is necessary on how hydrogen affects the material properties of welded microstructures. In this regard, each weld microstructure (HAZ and weld metal) has influence on the HAC susceptibility and respective hydrogen diffusion. Thus, the present contribution summarizes different results obtained from experiments with grades T24 (CrMoV alloy) and T22 (CrMo) and thermally simulated HAZ. Tensile tests were conducted with hydrogen charged specimens and compared to hydrogen-assisted stress corrosion cracking results obtained from slow strain rate tests (SSRT) up to 200 degree Celsius. Electrochemical permeation and degassing experiments were performed to identify a particular weld microstructure influence on hydrogen diffusion and trapping (especially in the HAZ). The results showed that T24 base material has improved resistance to hydrogen-assisted degradation/cracking. In contrast, the as-welded HAZ had remarkably increased susceptibility (tesnile tests at hydrogen concentration of 1 to 2 ppm). SSRT experiments confirmed this at elevated temperatures for both the T24 and the T22. Hence, the evaluation of a particular degradation of the mechanical properties should be performed independently for each weld microstructure. In addition, the HAZ showed decreased diffusion coefficients (at room temperature) of approximately one magnitude compared to the base materials. Trapped hydrogen was determined in the T24 at temperatures up to 120 degree Celsius compared to 75 degree Celsius in the T22. This has to be considered in case of changing operational temperatures, e.g. in the case of start-up and shutdown processes of boiler components. T2 - 10th Conference on Trends in Welding Research CY - Tokyo, Japan DA - 11.10.2016 KW - Degradation of Mechanical Properties KW - Hydrogen KW - Creep-resistant Steel KW - Weld Joint KW - Diffusion PY - 2016 AN - OPUS4-37827 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - Hollow Specimen Method for Tests in High-Pressure Hydrogen Gas: The Role of Strain-Rate and Surface Quality N2 - The hollow specimen technique is a simple and economical technique that has the potential to make materials qualification with pressurised gaseous hydrogen widely accessible to academia and industry. This contribution focuses on the results obtained from assessing the influence of the specimen production and its response to hydrogen effects. Depending on the production method, different roughness and residual stresses can be expected on the inner hole surface of the specimens. This is relevant because an increase in stress concentration sites, e.g. notches, has been found to be associated with increased severity of hydrogen effects. The presence of strain-induced martensite caused by mechanical stress may also be detrimental and accelerate the embrittlement. To assess this influence, the inner hole of the hollow specimens was manufactured in two different ways: 1) only drilling; 2) EDM followed by honing. A representative steel widely used in hydrogen technologies was assessed, X5CrNi18-10 (AISI 304). Roughness measurements, and electron back-scatter diffraction (EBSD) analysis have been performed previous to mechanical testing to infer on the effect of the different production methods on the surface of the inner hole. Next, the specimens were mechanically tested via slow strain rate tensile tests in argon and in hydrogen, both at 150 bar and room temperature. Here, a strain-rate sensibility analysis was performed to investigate the influence of strain-rate on hydrogen degradation. T2 - International Conference on Hydrogen Safety 2025 CY - Seoul, South Korea DA - 22.09.2025 KW - Tensile Testing KW - Hollow Specimen Technique KW - High-Pressure Hydrogen Gas KW - Hydrogen Embrittlement KW - Surface Condition KW - Strain Rate PY - 2025 AN - OPUS4-64286 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - Hollow Specimen Method for Tests in High-Pressure Hydrogen Gas: The TransHyDE - H2HohlZug Project N2 - As the world moves towards a decarbonised economy, the demand for sustainable and low-carbon alternatives is growing rapidly. Hydrogen has an important role to play in this transition, but in order to make the most of hydrogen as an energy carrier, a comprehensive understanding of its impact on the integrity of structural materials is necessary. Metallic materials, mainly steels, are the most commonly used structural materials in various components throughout the hydrogen supply chain. Ensuring their sustainable and safe use in hydrogen technologies is a crucial factor in the development of the hydrogen economy. This is particularly important since hydrogen can promote crack formation and ultimately lead to premature failure in these materials when combined with mechanical load. This process is commonly known as Hydrogen Embrittlement and can occur in almost all the steels used for the hydrogen technologies. Extensive materials qualification is required for the rapid implementation of hydrogen technologies, however, most accepted, and standardised test methods for determining the effect of gaseous hydrogen on metallic materials describe complex and costly procedures that are only available to a very limited extent worldwide. The hollow specimen technique is a simple and economical method that has the potential to overcome the limitations of the current methods and complement them for qualifying metallic materials under high-pressure hydrogen gas. Unlike the conventional autoclave technique, this method requires significantly lower amounts of hydrogen, resulting in fewer safety measures and no need for complex equipment or a specialised laboratory. The technique's low investment and testing costs, simple operation, and shorter testing time make it an optimal for widespread use around the world, thereby increasing the output of results. Initial studies have demonstrated the feasibility of assessing hydrogen effects in metallic materials using the hollow specimen technique. This led to the establishment of an ISO committee to standardise the method. However, there are open questions that currently prevent the technique from being standardised for hydrogen testing. These open questions relate to specimen geometry, inner hole surface and gas quality and are being addressed in the H2HohlZug project, of which the overall aim is to systematically close the gaps towards a standard. This contribution presents the structure and milestones of the project, followed by initial results. T2 - TransHyDE Vollversammlung 2025 CY - Leipzig, Germany DA - 26.11.2025 KW - Hydrogen KW - Hydrogen Embrittlement KW - Hollow Specimen Technique KW - High-Pressure Gaseous Hydrogen KW - TransHyDE KW - H2HohlZug KW - Standardisation PY - 2025 AN - OPUS4-64938 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - El Harrab, Hayat A1 - Askar, Enis A1 - Franken, T. A1 - Mauss, F. T1 - Experimental and Kinetic Study of Lubrication Oil Composition on Hydrogen Auto-Ignition N2 - Hydrogen internal combustion engines (H₂ ICEs) present a promising alternative to conventional fuels, but they face challenges such as pre-ignition, where lubricating oils play a critical role. This study investigates the auto-ignition behavior of two base oils — Group II (mineral) and Group V (Ester) — and three formulated oils (Oils A, B, and C) at 20 bar using a heated constant-volume autoclave. Oil A and Oil B share a Group II (mineral) base, with Oil A containing lower levels of calcium-based detergents and higher levels of phosphorus-based antioxidants compared to Oil B. In contrast, Oil C is formulated with a Group V (ester) base oil, incorporating magnesium-calcium detergents. The auto-ignition temperature was measured in both air and stoichiometric hydrogen-air mixtures to assess the influence of oil composition, additives, and hydrogen addition on ignition characteristics. Results show that hydrogen’s AIT at 20 bar is 460°C but drops to 270°C with the addition of 0.2 ml of base oil. Base oils exhibited similar AITs in air (260°C) and hydrogen-air mixtures (270°C), with reactivity differences linked to molecular composition — ester (Group V) displayed lower reactivity compared to mineral oil (Group II). Formulated oils demonstrated slightly higher AITs (up to 290°C), where phosphorus-based additives reduced reactivity, while lower calcium content further slowed ignition. Among the tested oils, the ester-based oil with a mixture of calcium and magnesium detergents exhibited the lowest reactivity, making it a promising candidate for hydrogen engines. Additionally, reduced oxygen availability increased AIT by 10°C and prolonged ignition delay. A chemical analysis was also performed to evaluate the ignition properties of Group II (mineral) and Group V (ester) oils under varying temperatures. These findings highlight the impact of lubricant composition on pre-ignition behavior in H₂ ICEs, offering valuable insights for optimizing lubricant formulations. T2 - 12th European Combustion Meeting CY - Edinburgh, United Kingdom DA - 07.04.2025 KW - Hydrogen KW - Pre-Ignition KW - Group V Ester Oil KW - Auto-Ignition Temperature KW - Additive Effects KW - Ignition Delay Time KW - Group II Mineral Oil KW - Lubricating Oil PY - 2025 AN - OPUS4-64761 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fedelich, Bernard T1 - Constitutive modeling and lifetime prediction for a conventionally cast Ni-base superalloy under TMF loading N2 - Under cyclic thermomechanical loading, various effects such as strain accumulation, creep damage, ageing, fatigue etc. may occur in the material of a gas turbine blade. Depending on the loading conditions, all these effects contribute to reduce the lifetime of the component. Subject of the present work is the development of a material model to describe the mechanical effects mentioned above and to subsequently predict lifetimes by using simulated stress strain data. Starting point for deformation modeling is the well known viscoplastic model after Chaboche, which provides descriptions of isotropic and kinematic hardening, as well as dynamic and static recovery. The evolution equation for kinematic hardening model has been modified following the proposal of Ohno/Wang to better predict stress controlled cyclic strain accumulation, i.e. ratchetting. A damage variable has been included to represent tertiary creep according to the concept of Kachanov. Finally, the static recovery has been modified following Kindrachuk to account for strain induced ageing. The models parameters have been calibrated using isothermal test data only. The constitutive model has been validated by comparing experimental with predicted TMF stress-strain hystereses. Lifetime prediction is done with the TMF lifetime model proposed by Riedel. The model assumes that fatigue life is controlled by the propagation of short cracks. Besides pure fatigue, it takes the local creep deformations at the crack tip into account. The model is applied to a broad variety of isothermal and non isothermal tests over temperatures up to 950°C and different loading conditions. The evaluation shows that throughout satisfying results can be achieved using a limited number of model parameters for the whole test data base. T2 - 3rd International Workshop on Thermo-mechanical fatigue CY - BAM, Berlin, Germany DA - 27.04.2016 KW - TMF KW - Nickel base superalloy KW - Fatigue life assessment KW - Constitutive law PY - 2016 AN - OPUS4-35994 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Konert, Florian T1 - Evaluation of hydrogen effect on hardened and annealed 100Cr6 steel N2 - The use of hydrogen demands high safety requirements, since hydrogen can be absorbed by metallic materials and may cause hydrogen embrittlement (HE) under certain conditions. Slow strain rate (SSR) tensile testing is a widespread method to quantify the hydrogen-induced ductility loss of alloys. Here, the hollow specimen technique was used to evaluate the effect of 150 bar hydrogen on the tensile properties of solution annealed and hardened 100Cr6 steel, which is a common material for bearing systems. This technique reduces the required amount of hydrogen and minimizes the duration and costs of the tests performed compared to in-situ tensile tests in autoclaves. T2 - EPRI Workshop on Hydrogen Embrittlement 2024 CY - Oxford, UK DA - 23.06.2024 KW - Hydrogen KW - Hydrogen Embrittlement KW - Hollow Specimen Technique KW - 100Cr6 PY - 2024 AN - OPUS4-60476 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nietzke, Jonathan T1 - Influence of strain rate on the effect of hydrogen in pre-charged 316L stainless steel: A comparison of conventional and hollow specimen testing N2 - The growing demand for hydrogen requires an expansion of testing capabilities to assess the performance of metallic materials under hydrogen exposure. Considering only gaseous atmospheres, there is a variety of in-situ and ex-situ methods used to investigate the material behavior while or after exposed to hydrogen, respectively. Among these methods, a more conservative one is the in-situ testing at slow strain rates (SSRT) using conventional tensile specimens. While results obtained by a conservative procedure may be more applicable in many cases than those of ex-situ experiments, the tests are quite demanding, leading to limited testing capacities and high costs, especially for very slow strain rates. A possible solution that can enable in-situ testing at relatively low cost is the hollow specimen technique which gained increasing interest in the last decade. The main reasons are the minimal volume of hydrogen required and the elimination of a high-pressure hydrogen autoclave leading to significantly lower costs and enabling more laboratories worldwide to perform these tests. However, interpreting results from hollow specimens, especially when compared to conventional ones, remains a significant challenge. To address this, an experimental study was conducted using conventional and hollow specimens, both uncharged and pre-charged. Pre-charging was achieved using pure hydrogen (5.0, i.e. 99.999 %) at 100 bar and 300 °C for around 21 days. In order to obtain suitable reference specimens, other specimens were stored in argon at 100 bar and 300 °C for the same period of time. The tests were performed at various strain rates, down to 1E-6 1/s. While these ex-situ experiments are not directly comparable to in-situ tests with both types of specimens, they do provide some insights into the differences between the results of hollow and conventional specimens. Therefore, the elongation at fracture and reduction of area (RA) were compared, among other aspects. In addition, fractographical analyses were carried out using SEM images. Elongation at fracture was not significantly affected by hydrogen in conventional specimens, but it was slightly reduced in hollow specimens. RA, on the other hand, was lower for tests with hydrogen in both types of specimens across all strain rates. Moreover, the strain rate did not appear to influence hydrogen embrittlement in conventional specimens whereas in hollow specimens, tests conducted at higher strain rates (1E-4 1/s) showed a greater impact of hydrogen on elongation at fracture than those at lower strain rates (1E-6 1/s), which is contrary to the typical expectation. These findings suggest that the influence of hydrogen differs between conventional and hollow specimens, possibly due to factors such as surface roughness and differing stress states. However, further experiments are needed to fully understand these differences, including in-situ experiments to understand potential differences in hydrogen absorption between the two specimen types. T2 - EPRI Workshop on Hydrogen Embrittlement CY - Oxford, England, United Kingdom DA - 23.06.2024 KW - Stainless steel KW - Hollow specimen KW - Pre-charging KW - Hydrogen PY - 2024 AN - OPUS4-60494 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Shikomba, Nikanor A1 - Böllinghaus, Thomas A1 - Konert, Florian A1 - Sobol, Oded A1 - Blasón Gonzalez, Sergio A1 - Ohijeagbon, Idehai Olayemi A1 - Krafft, Eike A1 - Staudt, Thorsten T1 - Resistance of welded low-alloyed pressure vessel and pipeline steels in gaseous hydrogen N2 - Green hydrogen has become an essential energy carrier to achieve a climate-neutral economy. The production, storage, transport and usage of green hydrogen require safe and sustainable facilities and systems. The present contribution provides a procedure guideline to investigate the compatibility of steel welds for pressurised gaseous hydrogen applications under quasi-static mechanical loads, utilising the slow strain rate test and hollow specimen technique. Exemplarily, a weld of the low-alloyed steel P355NL1 was investigated and compared to an X65 weld. The results indicate that the base metal exhibits a higher ductility than the weld metal for both steels. Generally, hydrogen-exposed specimens exhibited a reduced strain, as compared to reference specimens. The hydrogen degradation, evaluated by the hydrogen embrittlement index, was more pronounced in the weld metal compared to the base P355NL1 material, whereas the X65 exhibited a larger hydrogen degradation of the base material than in the weld metal. Fractographic analysis of the test specimens revealed that hydrogen causes a transition from ductile to brittle features. Generally, the results of this study indicate a mild but significant degradation of the mechanical properties in terms of the ductility of the welds in the respective pressurised hydrogen atmosphere. KW - Hydrogen-assisted cracking KW - Welded joint KW - Slow strain rate test KW - Hollow Specimen KW - Structural steel PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634138 DO - https://doi.org/10.1007/s40194-025-02074-7 SN - 0043-2288 SP - 1 EP - 15 PB - Springer CY - Berlin AN - OPUS4-63413 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Junias, Josua Kondja A1 - Holtappels, Kai A1 - Liebner, Christian A1 - Thewis, Max A1 - Askar, Enis A1 - Shaanika, Erasmus T1 - Hydrogen Mixtures Flammability Limits Prediction using Machine Learning Models N2 - Flammability characteristics of hydrogen mixtures have been extensively investigated at different initial conditions(temperature and pressure). Based on the available experimental datasets, empirical and semi-empirical models are commonly used to calculate flammability limits in dependance to initial conditions and mixture composition to reduce the experimental effort. However, unevenly distributed empirical data and the complex non-linear relationship characteristics of these data present significant challenges to empirical flammability limits prediction methods under various mixture initial conditions. Moreover, the empirical models and semi-empirical models only cover some influencing parameters, respectively. To address these issues, the present study adapts a machine learning (ML) approach for improving the hydrogen-air/oxygen-inert gas mixture flammability limits prediction at different conditions with a holistic approach. A Multi-Layer Perceptron (MLP) model was trained, validated, and tested using key input features such as flammability state, initial mixture temperature, equivalence ratio, inert gas concentration, adiabatic flame temperature, and Lewis numbers. Data augmentation techniques were conducted on experimental datasets to improve the predictive capability of the model. The models’ performance was compared with empirical flammability limit prediction methods. The goal is to deliver fast, reliable, and more accurate predictions across different scenarios with a single prediction model. Most importantly, the machine learning approach offers a cost-effective and robust alternative to existing empirical flammability limit prediction methods, thus also reducing the experimental effort for explosion limits determination. T2 - 11th International Conference on Hydrogen Safety (ICHS) 2025 CY - Seoul, South Korea DA - 22.09.2025 KW - Machine Learning KW - Flammability Limits PY - 2025 SN - 979 -12 -243 -0274 - 2 SP - 1389 EP - 1401 AN - OPUS4-64624 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Popiela, Bartosz A1 - Günzel, Stephan A1 - Mair, Georg W. T1 - Discussion of creep phenomena during initial loading of type 4 composite pressure vessels N2 - To maintain the highest safety standards for compressed gas storage in composite pressure vessels, a deeper understanding of their ageing mechanism is required. In this study, two designs of type 4 cylinders were manufactured the only difference being the internal pressure function used during the filament winding process. Hence, their residual stress state and the quality of the composite layers varied. Ten pressure vessels were initially loaded under sustained pressure and increased temperature and later subjected to slow burst tests. Comparing the results with cylinders tested in a pristine state underlines a significant improvement in the performance of initially loaded cylinders of one of the designs. This phenomenon was caused by a significant decrease of the scattering of burst pressures within a sample. At the same time, a slight decrease of the burst pressures could be observed. An explanation of this behavior could be supported by strain measurements with fiber optic sensors, which were embedded in the composite material. The strains measured during the initial loading indicate a stress redistribution, which has an impact on the strength of the pressure vessel. Moreover, an increased stiffness during the slow burst tests after initial loading was observed that indicates a better exploitation of the individual layers of the composite structure. The study supports previous observations on the increased performance after initial loading and provides new insights into the strain development in creep effects in type 4 pressure vessels. T2 - Pressure Vessels & Piping Conference PVP2025 CY - Montreal, Quebec, Canada DA - 20.07.2025 KW - Type 4 pressure vessel KW - Creep KW - Fiber optic sensors KW - Slow burst test KW - Mechanics of composites PY - 2025 SN - 978-0-7918-8907-7 VL - 2025 SP - 1 EP - 7 PB - ASME AN - OPUS4-63897 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kromm, Arne T1 - Werkstoffsichere Dickblechschweißung und KI N2 - Der Vortrag zeigt, welche Herausforderungen beim Schweißen sogenannter Dickblechverbindungen bestehen und welche Strategien zur Lösung genutzt werden können. Ansätze zur Fehlerprävention werden vorgestellt. Es wird dargestellt, wie KI-basierte Methoden die Fehlererkennung erleichtern. Letztlich werden Potentiale zur effizienten Fehlerbeseitigung aufgezeigt und der Anwendernutzen herausgestellt. T2 - Mitgliederversammlung der Forschungsvereinigung Stahlanwendung e. V. CY - Essen, Germany DA - 17.12.2025 KW - UP-Schweißen KW - Eigenspannungen KW - Künstliche Intelligenz KW - Reparatur PY - 2025 AN - OPUS4-65210 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröpfer, Dirk T1 - Residual stress evaluation using the contour method of an additive manufactured high-strength steel solid cuboid N2 - Direct Energy Deposition with Arc (DED-Arc) enables the weight-optimized and near-net-shape manufacturing of complex structures. Lightweight construction principles allow a reduction of CO2 emissions by saving time, costs, and resources. Further optimisations can be achieved by using high-strength steel. This allows for a reduction in wall thickness and optimisation of weight. However, manufacturing intricate geometries using high-strength steels poses challenges in managing residual stresses (RS), which are essential for ensuring the structural integrity of welded components. High residual stresses can increase the risk of cold cracking, arising from the complex interactions between material properties, process conditions, and component design. Despite the availability of suitable filler metals, the lack of comprehensive knowledge and guidelines on residual stress formation limits the industrial application. Therefore, in the present study, the contour method (CM) was used to analyse the full field longitudinal residual stresses in an solid cuboid component (dimensions: 120 × 50 × 35 mm³) manufactured by DED-Arc. The CM enables the analysis of the two-dimensional map of residual stresses normal to a cutting plane using a finite element model. For this purpose, a solid cuboid component was welded fully automatically with a high-strength solid wire specially adapted for DED-Arc (yield strength > 790 MPa) onto conventionally manufactured substrates made of S690QL. The residual stresses from CM in the volume are compared with residual stress analyses using X-Ray diffraction on the surface. Additionally, comparative data from previous studies on hollow cuboid structures was included in order to identify similarities and differences in the resulting stress state, and to complement and validate the CM results. These results demonstrate the significant influence of the geometry on the residual stress profiles within the solid cuboid in relation to the open hollow. T2 - 4th International Conference on Advanced Joining Processes 2026 CY - Coimbra, Portugal DA - 16.10.2025 KW - Residual stress KW - Contour method KW - DED-Arc/M KW - High-strength steel KW - Filler metals KW - Neutron diffraction PY - 2025 AN - OPUS4-65209 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pittner, Andreas A1 - Fabry, Cagtay A1 - Thiele, Marc A1 - Artinov, Antoni A1 - Rethmeier, Michael T1 - Automated Arc Welding and Sensor Based Quality Assessment for Enhancing Fatigue Strength and Structural Reliability of Offshore Wind Turbine Supports N2 - Offshore wind energy plays a crucial role in achieving a carbon dioxide free industrial sector in the coming decades. However, foundation systems for offshore wind turbines significantly impact the overall installation process, posing technical and regulatory challenges. Adopting lightweight design principles in steel construction such as dissolved load bearing structures in jacket foundations offers substantial potential for reducing resource consumption, particularly steel usage. This presentation explores the complete digitalization of welding manufacturing and testing processes, enabling fully automated production and data driven quality assessment of tubular nodes, which are vital components of jacket foundations. The study also investigates the relationship between seam geometry and fatigue strength inspired by bionic design principles. The results demonstrate that tubular nodes can be welded entirely automatically, accommodating geometric tolerances, and that seam geometries ca n be precisely manufactured according to suggestions from e.g. numerical models or other sources . These advancements significantly enhance the fatigue strength and service life of offshore wind turbine support structures. T2 - IIW Annual Assembly 2025 CY - Genova, Italy DA - 23.06.2025 KW - Automated gas metal arc welding KW - Quality assessment and control KW - Support structures KW - Fatigue PY - 2025 AN - OPUS4-65232 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Graebner, Maraike A1 - Giese, Marcel A1 - Lorenz, Svenja A1 - Treutler, Kai A1 - Schröpfer, Dirk A1 - Wesling, Volker A1 - Kannengießer, Thomas T1 - Wear resistance of modified NiMoCrSi claddings in relation to the resulting surface machinability via ultrasonic-assisted milling N2 - In the field of plastics processing, extruder screws are subjected to significant wear stresses. The extruder screw is the main wear component in those production machines and is usually coated with intermetallic wear protection alloys composed of Ni-based alloys, specifically Colmonoy C56 PTA (NiMoCrSi). There is a growing demand for providing an economic machinability of these alloys to achieve defined contours with a sufficient surface integrity. Recent investigations exhibit promising results applying ultrasonic milling for such hard-to-cut materials. The Colmonoy C56 is modified by various alloying additions Ti, Nb, Mo, Hf, and Al, and then cladded on a steel S355 via Plasma Transferred Arc process. The effect of alloying additions on the microstructure is analyzed regarding their resistance to abrasive and adhesive wear. With Miller test ASTM G75 the influence of alloying elements on resistance to abrasive wear for two abrasive materials is investigated (high-grade corundum F220 and quartz powder). The wear loss is not increased for additions of Nb and Ti compared to the base material C56. Modifications with Hf or Al reduces the resistance to abrasive wear and significantly increases material loss. The extruder screw is also subject to adhesive wear, which can be quantified by means of the pin-roll test. It is demonstrated that the addition of Hf, for example, contributes to a reduction in wear loss. Aim of the investigations is to find suitable modifications for the wear claddings of C56 for a sufficient machineability, without compemising the wear resistant. The machinability is considerably affected by the alloy additions, and is determined using ultrasonic-assisted milling. The addition of hafnium reduces machinability, i.e. significantly increases cutting forces. The incorporation of Nb exhibits a significant reduction of cutting forces, and results in reduced tool wear and an enhanced of surface integrity (roughness, density of defects, residual stresses). KW - Colmonoy C56 KW - PTA welding KW - Adhesive wear KW - Abrasive wear KW - Ultrasonic-assisted milling process KW - Surface integrity KW - Service life and efficiency KW - Substitution of critical raw materials PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-651530 DO - https://doi.org/10.1016/j.wear.2025.205830 SN - 0043-1648 VL - 571 SP - 1 EP - 10 PB - Elsevier B.V. AN - OPUS4-65153 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Inhalt der Verordnungen für Heizungsanlagen - Überblick N2 - Seit dem 26.09.2015 gelten in Deutschland Anforderungen an die umweltgerechte Gestaltung und die Energiekennzeichnung von Heizgeräten und Verbundanlagen mit Heizgeräten. Der Vortrag stellt die zugrundeliegenden EU-Verordnungen und die sich ergebenden Konsequenzen überblicksmäßig vor. T2 - Kolloquium Marktüberwachung im Bereich Heizungsanlagen CY - Berlin, Germany DA - 06.04.2016 KW - Heizgeräte KW - Verbundanlagen KW - Umweltgerechte Gestaltung KW - Ökodesign KW - Energieverbrauchskennzeichnung PY - 2016 AN - OPUS4-36924 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Askar, Enis T1 - Hydrogen Safety - Explosion Protection for Hydrogen Applications N2 - In this lecture the safety related properties og hydrogen compared to other fuel gases and the explosion protection measures of avoiding flammable mixtures, avoiding ignition sources and mitigating the consequences of explosions when handling hydrogen and hydrogen mixtures are presented. The Joint European Summer School JESS 2021 addresses these issues by offering high quality graduate level courses on selected topics of vehicle technology, innovation & business development, safe handling of hydrogen, and modelling. The course content is tailored to the needs of a diverse audience: newcomers to the field, experienced students, and young professionals working at the forefront of fuel cell and hydrogen applications. T2 - Joint European Summer School (JESS) CY - Online meeting DA - 06.09.2021 KW - Explosionsschutz KW - Explosionsgrenzen KW - Zündenergie KW - Zündquellen KW - Auswirkung von Explosionen PY - 2021 AN - OPUS4-53808 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Askar, Enis A1 - Schröder, Volkmar A1 - Seemann, A. A1 - Schuetz, S. T1 - Power-to-Gas: Safety Characteristics of Hydrogen/NaturalGas-Mixtures N2 - Safety characteristics for explosion protection of natural gas/hydrogen mixtures relevant in connection with the Power2Gas technology were studied in this work. Lower explosion limits (LEL) and upper explosion limits (UEL), limiting oxygen concentrations (LOC), maximum experimental safety gaps (MESG), maximum explosion pressures (pmax) and maximum rates of pressure rise (dp/dt)max were determined experimentally in dependence of the hydrogen fraction. Adding hydrogen did mainly effect the UEL, LOC, MESG and (dp/dt)max. The mixtures become more "critical" concerning the explosion hazards with increasing hydrogen fraction. However, the dependency of the safety characteristics from the hydrogen fraction is mainly not linear. Adding up to 10% hydrogen to natural gas had nearly no effect on the safety characteristics. More significant effects on the safety characteristics were observed at hydrogen fractions of more than 25%. For example the explosion group changes from IIA to IIB. Considering the huge explosion region and very high (dp/dt)max of hydrogen compared to natural gas, even adding 50% hydrogen to natural gas has a rather small effect on these characteristics. Furthermore pmax of hydrogen/natural-gas mixtures can be calculated with good accuracy assuming ideal adiabatic conditions. EL and LOC of natural gas/hydrogen mixtures in ternary systems with inert gas and air were calculated in dependence of the type of inert gas with the so called “model of constant adiabatic flame temperature profiles”. KW - Explosion protection KW - Hydrogen safety KW - Hydrogen enriched natural gas KW - Energy storage PY - 2016 SN - 78-88-95608-39-6 DO - https://doi.org/10.3303/CET1648067 SN - 2283-9216 VL - 2016/48 SP - 397 EP - 402 PB - AIDIC AN - OPUS4-36788 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sobol, Oded T1 - BAM’s role in materials science and hydrogen in metals: TOF-SIMS imaging N2 - Due to its low mass and high diffusivity in presence of compositional, thermal and mechanical gradients, hydrogen within a metallic microstructure can result in severe loss in ductility even at low concentrations and might lead eventually to a catastrophic and unpredictable failure of structural components during service. In this context, hydrogen mapping at the microscale is still considered among the most important challenges on the pathway towards a better understanding of the hydrogen transport and assisted cracking phenomena in metals, specifically in structural components, e.g. steels. Among the very few available techniques to localize hydrogen at the microscale, Time-of-flight secondary ion mass spectrometry (ToF-SIMS) was proven to be a reliable tool. Based on the assumption that deuterium influence the microstructure similarly to hydrogen, in the following contribution ToF-SIMS was applied as the main technique to detect and locally map the deuterium distribution in several alloys: lean 2101 and standard 2205 duplex stainless steel (DSS), AISI 304L austenitic stainless steel and titanium 6Al-4V alloy. These alloys were selected as case studies in this work due to the wide use of them in many applications and environments which frequently provide critical conditions for hydrogen absorption and assisted degradation. The innovative design of in-situ and ex-situ experiments enabled us to elucidate the permeation, transport and trapping of deuterium in the microstructure in sub-micron resolution for the first time. In addition to the novel experimental setups, further progress was gained by applying computational multivariate data analysis (MVA) on the raw data and data fusion with high resolution structural characterization methods (scanning electron microscopy and electron back-scattered diffraction – SEM/EBSD). This combination allowed us to correlate the deuterium distribution and the influence on the microstructure. T2 - 4th Symposium on Innovative Measurement and Analysis for Structural Materials CY - Tokyo, Japan DA - 13.11.2018 KW - ToF-SIMS KW - Duplex stainless steel KW - Austenitic stainless steel KW - Principal Component Analysis KW - Data-fusion PY - 2018 UR - https://unit.aist.go.jp/tia-co/project/SIP-IMASM/sympo/2018/index.html AN - OPUS4-46867 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Epishin, A. I. A1 - Link, T. A1 - Nolze, Gert A1 - Svetlov, I. L. A1 - Bokshtein, B. S. A1 - Rodin, A. O. A1 - Saliwan Neumann, Romeo A1 - Oder, Gabriele T1 - Diffusion processes in multicomponent nickel-base superalloy-nickel system N2 - Optical and scanning electron microscopy, as well as electron microprobe analysis and electron backscatter diffraction, have been used to study diffusion processes that occur in a diffusion pair that consistsof a single-crystal CMSX-10 nickel-base superalloy and polycrystalline nickel, at temperatures of 1050–1250°C. It has been found that, in this system, the distributions of γ-stabilizing elements (Cr, Co, W, and Re) are described by the Boltzmann solution for diffusion between two semiinfinite plates of a binary alloy. The processing of these distributions has shown that the diffusion coefficients of Cr, Co, W, and Re in the multicomponent system are close to those in binary alloys of these elements with Ni. The diffusion redistribution of the elements leads to the dissolution of the γ′ phase in the nickel-base superalloy, growth of nickel grains toward the superalloy constituent of the diffusion pair, and the formation of porosity on both sides of the migrating interface, which is determined from a crystal misorientation of the alloy single crystal and nickel grains. KW - Ni-base superalloy KW - Interface KW - Diffusion KW - Phase transformation KW - Porosity PY - 2014 SN - 0031-918X VL - 115 IS - 1 SP - 21 EP - 29 AN - OPUS4-37980 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Askar, Enis T1 - Ignition Behaviour and Challenges for Hydrogen Safety N2 - The presentation is divided in two parts. In the first part the significance of mechanical impacts as ignition source for hydrogen containing atmospheres is shown and recent results of a research project evaluating ignition probabilities under different conditions is presented. In the second part future challenges in the field of hydrogen safety are discussed. Finally, the German National Hydrogen Safety Alliance is introduced. T2 - Hydrogen Online Workshop 2024 CY - Online meeting DA - 05.06.2024 KW - Explosion protection KW - Mechanical impacts KW - Ignition source KW - German National Alliance for Hydrogen Safety PY - 2024 AN - OPUS4-60288 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Schröder, Volkmar A1 - Askar, Enis A1 - Habib, Abdel Karim A1 - Tashqin, T. T1 - Sicherheitstechnische Eigenschaften von Erdgas-Wasserstoff-Gemischen N2 - Bei der Power-to-Gas-Technologie wird überschüssiger Strom aus erneuerbaren Energien durch Elektroly-se von Wasser in Wasserstoff umgewandelt. Dieser Wasserstoff kann als „chemischer Energiespeicher“ dienen und rückverstromt werden oder aber in das Erdgasnetz eingespeist werden. Die BAM hat die Aus-wirkungen von Wasserstoffzusätzen zum Erdgas im Hinblick auf den Explosionsschutz untersucht und sicherheitstechnische Kenngrößen für Erdgas-Wasserstoff-Gemische bestimmt. Untersucht wurden die Explosionsgrenzen, die Sauerstoffgrenzkonzentrationen, die maximalen Explosi-onsdrücke, die KG-Werte und die Normspaltweiten. Für die Messungen sind zwei Modellgase eingesetzt worden, reines Methan und ein Modell-Erdgas mit Anteilen höherer Kohlenwasserstoffe. Sie repräsentie-ren die Bandbreite der in Deutschland eingesetzten Erdgase. Die Untersuchungen ergaben, dass bei einem Zusatz von bis zu 10 Mol-% Wasserstoff keine der untersuchten Kenngrößen relevant beeinflusst wird. Die Gemische haben nur geringfügig erweiterte Explosionsbereiche und bleiben, wie die reinen Erdgase, in der Explosionsgruppe IIA. Auch die maximalen Explosionsdrücke und die zeitlichen Druckanstiege bei den Gasexplosionen werden nur wenig beeinflusst. Vergleichende Berechnungen zur Festlegung von explosionsgefährdeten Bereichen (Ex-Zonen) auf Basis von Gasausbreitungsberechnungen ergaben ebenfalls nur geringfüge Unterschiede im Rahmen der Fehler-toleranz für Erdgas und Erdgas-Wasserstoff-Gemische mit bis zu 10 Mol-% Wasserstoff. Die Berechnun-gen sind in der BAM nach einem Freistrahlmodell von Schatzmann und mit dem häufig bei Gasnetzbetrei-bern eingesetzten e.BEx-Tool® durchgeführt worden. Der Einsatz von Gaswarngeräten, die für reines Erdgas geeignet sind, ist für Erdgas-Wasserstoff-Gemische mit bis zu 10 Mol-% Wasserstoff grundsätzlich möglich, erfordert aber eine gesonderte Sicher-heitsbewertung und ggf. eine Nachkalibrierung. N2 - Power-to-Gas technology is used to convert excess power from renewable energies to hydrogen by means of water electrolysis. This hydrogen can serve as "chemical energy storage" and be converted back to elec-tricity or be fed into the natural gas grid. BAM has studied the addition of hydrogen to natural gas in view of explosion protection and has determined safety characteristics for natural gas-hydrogen mixtures. BAM investigated the explosion limits, the limiting oxygen concentrations, the maximum explosion pres-sures, KG values and the MESG. Two model gases have been investigated, pure methane and a model gas with portions of higher hydrocarbons. They represent the range of natural gases which are used in Germa-ny. The investigations have shown that none of the examined characteristics is affected significantly by the addition of up to 10 mol% hydrogen. The explosion ranges are increased only slightly and the mixtures remain in explosion group IIA; as is pure natural gas. Also the maximum explosion pressure and the rates of pressure rise of gas explosions are almost unaffected. Comparative calculations – on the basis of gas dispersion calculations – to determine hazardous areas (explosion zones) for pure natural gas and natural gas-hydrogen mixtures with up to 10 mol% hydrogen, also revealed only minor differences within the margin of error of the calculation methods. The calcula-tions were executed at BAM according to the free jet model from Schatzmann and with the e.BEx-Tool®, often applied by gas grid operators. In principle, gas detectors that are suitable for natural gas can be used for natural gas-hydrogen mixtures with a maximum of 10 mol% hydrogen. However, this requires a separate safety assessment and, if nec-essary, a recalibration. KW - Power-to-Gas KW - Erneuerbare Energien KW - Energiespeicherung KW - Wasserstofftechnologie KW - Explosionsschutz KW - Erdgas-Wasserstoff-Gemische PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-372977 SP - 1 EP - 36 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-37297 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröder, Volkmar A1 - Askar, Enis A1 - Tashqin, T. T1 - Sicherheitstechnische Eigenschaften von Gemischen aus Wasserstoff und Erdgas N2 - Bei der Power-to-Gas-Technologie wird überschüssiger Strom aus erneuerbaren Ener-gien durch Elektrolyse von Wasser in Wasserstoff umgewandelt. Dieser Wasserstoff kann als „chemischer Energiespeicher“ dienen und rückverstromt werden oder aber in das Erdgasnetz eingespeist werden. Die BAM hat die Auswirkungen von Wasserstoffzu-sätzen zum Erdgas im Hinblick auf den Explosionsschutz untersucht und sicherheitstechnische Kenngrößen für Erdgas-Wasserstoff-Gemische bestimmt. Von besonderem Interesse waren dabei die Explosionsgrenzen, die Sauerstoffgrenzkonzentration, die maximalen Explosionsdrücke, die KG-Werte und die Normspaltweiten. Für die Messungen sind zwei Modellgase eingesetzt worden, reines Methan und ein Modell-Erdgas mit Anteilen höherer Kohlenwasserstoffe. Sie repräsentieren die Bandbreite der in Deutschland eingesetzten Erdgase. Die Untersuchungen ergaben, dass bei einem Zusatz von bis zu 10 Mol-% Wasserstoff keine der untersuchten Kenngrößen signifikant beeinflusst wird. Die Gemische haben nur geringfügig erweiterte Explosionsbereiche und bleiben, wie die reinen Erdgase, in der Explosionsgruppe IIA. Auch die maximalen Explosionsdrücke und die zeitlichen Druckanstiege bei den Gasexplosionen werden nur wenig beeinflusst. T2 - Kolloquium zur chemischen und physikalischen Sicherheitstechnik CY - Berlin, Germany DA - 14.06.2016 KW - Wasserstoff KW - Erdgasnetz KW - Energiespeicherung KW - Explosionsschutz KW - Sicherheitstechnische Kenngrößen PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-373099 SN - 978-3-9817853-5-7 SN - 0938-5533 VL - 2016 SP - 60 EP - 67 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin, Germany AN - OPUS4-37309 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Askar, Enis T1 - Sicherheitstechnische Eigenschaften von Erdgas/Wasserstoff-Gemischen - Auswirkungen auf den Explosionsschutz N2 - Hinsichtlich ihrer sicherheitstechnischen Kenngrößen (STK) unterscheiden sich Wasserstoff und Erdgas zum Teil stark. Im Vortrag werden verschiedene STK von Erdgas/Wasserstoff-Gemischen im Abhängigkeit des Wasserstoffanteils vorgestellt und die Auswirkung der Beimischung von Wasserstoff zum Erdgas auf die Wirksamkeit von Explosionsschutzmaßnahmen erläutert. T2 - DVGW-Kongress 2021 "Gasinfrastruktur für Erdgas-H2-Gemische" CY - Online meeting DA - 07.10.2021 KW - Explosionsschutz KW - Explosionsgrenzen KW - Zündenergie KW - Power to Gas KW - Erdgasnetz KW - Zündquellen PY - 2021 AN - OPUS4-53725 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mosquera Feijoo, Maria T1 - Thermal-mechanical fatigue of oxide scales in cyclic water vapor oxidation of 9-12 % Cr steels N2 - Ferritic-martensitic steels with 9-12 % Cr-content are widely used as high temperature construction materials in power plant due to their high temperature properties such as creep resistance, strength, and favorable oxidation resistances. However, typical operating conditions include cyclic thermal/mechanical loading, and as a result the oxide scale might fail; cracks are formed and the oxide scale is spalled off. The oxide spalls can cause steam tube blocking and local thermal stresses, which might provoke shorter component service life. This work investigates the scale spallation behavior of ferritic-martensitic steels under cyclic load condition between 320°C and 620°C for up to 210 cycles in pure steam. All samples were isothermally pre-oxidized at 620°C for 500 h in water steam with 30 bar pressure to create an initial magnetite layer with low porosity. Different sample shapes, rectangular coupons, full rings and U-shape segments, are investigated to evaluate the impact of the geometry on these conditions. After oxidation experiments the oxidation kinetics in terms of mass change, metal loss and thickness scale is determined. In addition, the integrity of the oxide layer as well as its adherence to the matrix are characterized by modified hardness tests and scratch tests. Breakage of the layers at lower applied forces indicates a substantial loss of adhesion strength at intermediate cycle numbers. T2 - EUROCORR 2017 CY - Prague, Czech-Republic DA - 03.09.2017 KW - Geometry influence KW - Therma-mechanical fatigue KW - Oxide layer KW - Cyclic test KW - Scale adherence PY - 2017 AN - OPUS4-42635 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Röhsler, Andreas A1 - Sobol, Oded A1 - Hänninen, H. A1 - Böllinghaus, Thomas T1 - In-situ ToF-SIMS analyses of deuterium re-distribution in austenitic steel AISI 304L under mechanical load N2 - Hydrocarbons fuel our economy. Furthermore, intermediate goods and consumer products are often hydrocarbon-based. Beside all the progress they made possible, hydrogen-containing substances can have severe detrimental effects on materials exposed to them. Hydrogen-assisted failure of iron alloys has been recognised more than a century ago. The present study aims to providing further insight into the degradation of the austenitic stainless steel AISI 304L (EN 1.4307) exposed to hydrogen. To this end, samples were electrochemically charged with the hydrogen isotope deuterium (2H, D) and analysed by scanning electron microscopy (SEM), electron back-scatter diffraction (EBSD) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). It was found that deuterium caused a phase transformation from the original γ austenite into ε- and α’-martensite. Despite their low solubility for hydrogen, viz. deuterium, the newly formed phases showed high deuterium concentration which was attributed to the increased density of traps. Information about the behaviour of deuterium in the material subjected to external mechanical load was gathered. A four-point-bending device was developed for this purpose. This allowed to analyse in-situ pre-charged samples in the ToF-SIMS during the application of external mechanical load. The results indicate a movement of deuterium towards the regions of highest stress. KW - ToF-SIMS KW - Hydrogen KW - Deuterium KW - AISI 304L KW - EBSD PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-505142 DO - https://doi.org/10.1038/s41598-020-60370-2 VL - 10 IS - 1 SP - 3611 PB - Nature AN - OPUS4-50514 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Konert, Florian A1 - Campari, Alessandro A1 - Nietzke, Jonathan A1 - Sobol, Oded A1 - Paltrinieri, Nicola A1 - Alvaro, Antonio T1 - Evaluation of the tensile properties of X65 pipeline steel in compressed gaseous hydrogen using hollow specimens N2 - Hydrogen has great potential on the path towards decarbonization of the energy and transport sectors and can mitigate the urgent issue of global warming. It can be sustainably produced through water electrolysis with potentially zero emissions, and efficiently used (e.g., in fuel cell systems). Despite its environmental advantages, hydrogen-metal interactions could result in the degradation of the mechanical properties of several structural materials. In order to determine the magnitude of the material degradation in relation to hydrogen exposure, extensive material testing is required. The standardized procedure for in-situ testing for the quantification of the impact of compressed gaseous hydrogen (CGH2) relies on the utilization of an autoclave around the tested specimen. Such test set-up is complex, expensive, time-consuming and requires special equipment, trained personnel, and strict safety procedures. A relatively recent method to circumvent these issues and provide affordable results consists of using hollow specimens, thus applying the hydrogen pressure inside rather than outside the specimen. It allows to reduce the volume of hydrogen by several orders of magnitude and to perform the tests more efficiently and in a safer manner. This study focuses on evaluating the tensile properties of X65 vintage pipeline steel tested in a high-pressure hydrogen environment using hollow specimens. Tests are performed in 6 MPa H2 and Ar at the nominal strain rate of 10−6 s−1 to evaluate the reduced area at fracture and the elongation loss. The effect of surface finishing on crack initiation and propagation is investigated by comparing two different manufacturing techniques. In this way, this study provides insights into the applicability of a novel, reliable, and safe testing method which can be used to assess the hydrogen-assisted ductility loss in metallic materials. KW - Mechanical Engineering KW - Hydrogen Embrittlement KW - SSRT KW - Hollow specimen KW - Pipeline steel KW - In-situ tensile test PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-595887 DO - https://doi.org/10.1016/j.prostr.2024.01.074 SN - 2452-3216 VL - 54 SP - 1 EP - 8 PB - Elsevier B.V. AN - OPUS4-59588 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Konert, Florian A1 - Wieder, Frank A1 - Nietzke, Jonathan A1 - Meinel, Dietmar A1 - Böllinghaus, Thomas A1 - Sobol, Oded T1 - Evaluation of the impact of gaseous hydrogen on pipeline steels utilizing hollow specimen technique and μCT N2 - The high potential of hydrogen as a key factor on the pathway towards a climate neutral economy, leads to rising demand in technical applications, where gaseous hydrogen is used. For several metals, hydrogen-metal interactions could cause a degradation of the material properties. This is especially valid for low carbon and highstrength structural steels, as they are commonly used in natural gas pipelines and analyzed in this work. This work provides an insight to the impact of hydrogen on the mechanical properties of an API 5L X65 pipeline steel tested in 60 bar gaseous hydrogen atmosphere. The analyses were performed using the hollow specimen technique with slow strain rate testing (SSRT). The nature of the crack was visualized thereafter utilizing μCT imaging of the sample pressurized with gaseous hydrogen in comparison to one tested in an inert atmosphere. The combination of the results from non-conventional mechanical testing procedures and nondestructive imaging techniques has shown unambiguously how the exposure to hydrogen under realistic service pressure influences the mechanical properties of the material and the appearance of failure. KW - Energy Engineering and Power Technology KW - Condensed Matter Physics KW - Fuel Technology KW - Renewable Energy, Sustainability and the Environment KW - µCT KW - Hollow Specimen Technique KW - Hydrogen Embrittlement PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-595077 DO - https://doi.org/10.1016/j.ijhydene.2024.02.005 SN - 0360-3199 VL - 59 SP - 874 EP - 879 PB - Elsevier B.V. AN - OPUS4-59507 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -