TY - CONF A1 - Law, D. W. A1 - Sturm, Patrick A1 - Gluth, Gregor A1 - Gunasekara, C. ED - Valente, I. B. ED - Ventura Gouveia, A. ED - Dias, S. S. T1 - Effect of Curing Temperature on the Alkali Activation of German Brown Coal Fly Ash N2 - Due to environmental concerns regarding the use of Portland cement as the principal binder material in concrete and mortar it is imperative to identify alternative materials that could reduce the carbon footprint of the construction industry. One alternative to address these issues is the use of alkali activated materials, in particular, when based on waste streams that currently have no or only limited industrial application. This paper reports a preliminary study into the synthesis of geopolymer mortar utilizing Brown Coal Fly Ash. The ash had a CaO content of ~39%, indicating that synthesis at ambient or low temperature may be feasible. The paper reports initial trials on the effect of curing temperature, ambient to 120 °C, on the mechanical properties of the mortars produced. The results showed that ambient cured mortar achieved a compressive strength of 6.5 MPa at 3 days. A curing temperature of 60 °C gave the optimum results with a compressive strength of almost 20 MPa and a flexural strength of 3.5 MPa obtained. T2 - 3rd RILEM Spring Convention and Conference (RSCC 2020) CY - Guimarães, Portugal DA - 10.03.2020 KW - Alkali-activated materials KW - Brown Coal Fly Ash KW - Lignite Coal PY - 2021 SN - 978-3-030-76550-7 SN - 978-3-030-76551-4 DO - https://doi.org/10.1007/978-3-030-76551-4_7 SP - 69 EP - 77 PB - Springer CY - Cham AN - OPUS4-53072 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Herbst, Tristan T1 - Konzept zur ganzheitlichen Nachhaltigkeitsbewertung des Abbruchs und der Aufbereitung von Mauerwerk N2 - Mit der vorliegenden Arbeit wurde ein methodisches Konzept zur ganzheitlichen Nachhaltigkeitsbewertung des Abbruchs und der Aufbereitung von Mauerwerk bereitgestellt. Das Bewertungskonzept ermöglicht einen ganzheitlichen Vergleich verschiedener Szenarien für den Abbruch und die Aufbereitung von Mauerwerk unter Berücksichtigung der Anwendung von Mauerwerkbruch und aussortierter Fremdstoffe zur Verwertung. Es kombiniert die Kosten-Wirksamkeitsanalyse, die Stoffflussanalyse, die Ökobilanzierung, die Betrachtung sozialer Aspekte und Wirtschaftlichkeitsbetrachtungen bei gleichzeitiger Berücksichtigung der Materialqualitäten. Das Bewertungskonzept basiert im Kern auf der Kosten-Wirksamkeitsanalyse (KWA) mit der Erweiterung um das Gesamtwirksamkeitswert-Kosten-Verhältnis. Hiermit können sowohl monetäre als auch nicht monetäre Effekte beurteilt werden. Ausgangspunkt der KWA ist ein klar definiertes Zielsystem. Im vorliegenden Fall wurden aus der EU-Abfallrahmenrichtlinie, dem Kreislaufwirtschaftsgesetz und der EU-Bauproduktenverordnung die vier Generalziele „Mensch und Umwelt“, „Ressourcenschonung“, „Ausreichende Materialqualität“ sowie „Wirtschaftlichkeit“ abgeleitet. Die Generalziele "Mensch und Umwelt" und "Ressourcenschonung" wurden weiter in Hauptziele, Ziele und Unterziele unterteilt. Die Quantifizierung und Beurteilung dieser beiden Generalziele erfolgt im Rahmen der Wirksamkeitsanalyse. Zur Quantifizierung der abstrakten Ziele wurden konkrete und messbare Zielkriterien ausgewählt, die üblicherweise bei der Ökobilanzierung und sozialorientierten Betrachtungen verwendet werden, z. B. Umweltauswirkungen, Material- und Energieverbrauch. Nach Ermittlung einer Gesamtwirksamkeit und den anfallenden Kosten für jedes Szenario wird das Gesamtwirksamkeit-Kosten-Verhältnis je Szenario errechnet. Dieses Verhältnis bildet die Grundlage für die abschließende Reihung der untersuchten Szenarien entsprechend ihrer nachhaltigkeitsbezogenen Wertigkeit im Sinne der europäischen und deutschen Kreislaufwirtschaft. Mit dem Konzept wird zukünftigen Nutzern eine strukturierte und methodische Bewertungsgrundlage als Planungsinstrument für Abbruchprojekte an die Hand gegeben. Gleichzeitig werden die Nutzer für bestehende Gestaltungsvarianten für den Abbruch und die Aufbereitung von Mauerwerk sowie für die vielfältigen Anwendungsmöglichkeiten von Mauerwerkbruch sensibilisiert. T3 - BAM Dissertationsreihe - 151 KW - Nachhaltigkeit KW - Kosten- und Wirksamkeitsanalyse KW - Mauerwerkbruch KW - Abbruch KW - Aufbereitung PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-384853 SN - 978-3-9817853-8-8 SN - 1613-4249 VL - 151 SP - 1 EP - 146 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-38485 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Drzymala, Sarah T1 - Instrumental analysis, metabolism and toxicity of cis- and trans-zearalenone and their biotransformation products N2 - Trans-Zearalenone(ZEN)is a non-steroidal estrogenic mycotoxin which frequently contaminates cereal grains worldwide. Ingestion of food and feed containing ZEN causes numerous mycotoxicoses in animals and possibly humans with pronounced estrogenic effects. Due to the trans-configurated double bond, ZEN isomerizes to the cis-configuration upon the influence of light. This work investigates the instrumental analysis, metabolism and toxicity of ZEN and cis- ZEN. The first part focused on the determination of ZEN in edible oils. Due to a maximum level of 400 µg/kg ZEN in the European Union (EU), reliable analytical methods are needed. A comprehensive method comparison proved dynamic covalent hydrazine chemistry (DCHC) to be the most suitable approach. Thus, an automated solid phase extraction (SPE) coupled online to high performance liquid chromatography (HPLC) was developed with the novelty of a covalent SPE step comprising the DCHC principle. The automated online system allows an accurate, selective and reliable quantification of ZEN in edible oils in compliance with EU performance criteria while significantly reducing workload and thereby personnel costs. In contrast to ZEN, reference standards and analytical methods are missing for cis- ZEN which causes a lack of data on the occurrence, fate and risks of cis-ZEN. Therefore, a native and an isotopically labeled cis-ZEN standard were synthesized and implemented in an existing stable isotope dilution analysis HPLC tandem mass spectrometry (HPLC-MS/MS) method. Using this method, a large extent of cis-ZEN formation was observed for ZEN contaminated maize germ oils when exposed to daylight which confirms that cis-ZEN can be a relevant food contaminant and should be considered in the analysis of food and feed. Furthermore, this work investigated the in vitro phase I metabolism of ZEN and cis-ZEN in rat and human liver microsomes by using HPLC-MS and -MS/MS analyses. The metabolic pathways of cis-ZEN were found to be essentially similar to ZEN including reduction and oxidation reactions generating α- and β-cis- zearalenol as well as 13- and 15-OH-cis-ZEN. A previously unidentified oxidative metabolic pathway for both isomers of ZEN results in the formation of cis-ZEN-11,12-oxide and ZEN-11,12-oxide in human liver microsomes. The estrogenicity of cis-ZEN and its reductive metabolites was assessed using the E-Screen assay. cis-ZEN proved to be slightly more estrogenic than ZEN. Biotransformation of cis-ZEN to β-cis-ZEL corresponds to a detoxification, whereas metabolism to α-cis-ZEL resembles a metabolic activation as its estrogenicity considerably exceeds that of cis-ZEN. The catecholic metabolites can be expected to show a decreased estrogenicity as demonstrated for 15-OH- ZEN. Independent of the estrogenic effects, the catecholic and epoxidic metabolites identified in this work can be expected to act genotoxic and carcinogenic. The epoxides in particular could fundamentally change the widely accepted view of ZEN causing adverse effects exclusively through endocrine disrupting actions. T3 - BAM Dissertationsreihe - 152 KW - Hydrazinchemie KW - Isotopenstandard KW - SPE-HPLC Automatisierung KW - Zearalenon KW - Isomerisierung PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-386016 SN - 978-3-9817853-9-5 SN - 1613-4249 VL - 152 SP - 1 EP - 160 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-38601 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stajanca, Pavol A1 - Krebber, Katerina T1 - Radiation-induced attenuation of perfluorinated polymer optical fibers for radiation monitoring N2 - Due to some of their unique properties, optical fiber dosimeters are attractive and extensively researched devices in several radiation-related areas. This work evaluates the Performance and potential of commercial perfluorinated polymer optical fibers (PF-POFs) for radiation Monitoring applications. Gamma radiation-induced attenuation (RIA) of two commercial PF-POFs is evaluated in the VIS spectral region. Influence of a dose rate and temperature on RIA measurement is investigated, along with defect stability and measurement repeatability. Co-extruded PF-POFs are identified as more suitable for radiation monitoring applications due to lower dose-rate dependence. With co-extruded PF-POF, RIA measurement holds potential for highly-sensitive radiation Monitoring with good reproducibility. The results show that operation in the blue part of the spectrum provides most favorable performance in terms of the largest nominal Radiation sensitivity, lower temperature, and dose-rate dependence as well as higher defect stability. We demonstrate for the first time to our knowledge, that PF-POFs can be used for distributed detection of radiation with doses down to tens of Grays. The off-the-shelf, user-friendly PF-POF could be of interest as a cheap, disposable sensor for various applications, especially of a more qualitative nature. KW - Perfluorinated polymer optical fiber KW - Cytop KW - Ionizing radiation KW - Radiation-induced attenuation KW - Gamma radiation monitoring PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-419504 DO - https://doi.org/10.3390/s17091959 SN - 1424-8220 VL - 17 IS - 9 SP - Article 1959, 1 EP - 12 PB - MDPI AN - OPUS4-41950 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bayat, Mehmet Emin A1 - Kipphardt, Heinrich A1 - Tiebe, Carlo A1 - Tuma, Dirk A1 - Engelhard, Carsten T1 - Trace-Level Ammonia–Water Interactions in Hydrogen: Challenges in Gas Purity Analysis Using Optical-Feedback Cavity-Enhanced Absorption Spectroscopy (OF-CEAS) N2 - Ammonia is a critical impurity in hydrogen fuel due to its irreversible poisoning effect on proton exchange membrane fuel cells. Therefore, international standards (e.g., ISO 14687) set a stringent threshold of 100 nmol/mol. Furthermore, with the growing potential use of ammonia as a hydrogen carrier, its accurate quantification is becoming increasingly important. However, the presence of trace humidity poses analytical challenges, as ammonia may interact with water or interfaces, thereby affecting its detectability. Therefore, the goal of this work is to enable accurate trace ammonia quantification for hydrogen purity measurements through fundamental studies of the methodological challenges. Here, low-pressure sampling (ultra)long-path Optical-Feedback Cavity-Enhanced Absorption Spectroscopy (OF-CEAS) was applied with an effective optical path length of approximately 6.17 km. We studied three average amounts of ammonia: (38.2 ± 0.8) nmol/mol, (74.8 ± 0.7) nmol/mol, and (112.1 ± 1.2) nmol/mol. Furthermore, these amounts were investigated at trace-humidity levels ranging from 0.8 to 8.5 ppmV. We observed a systematic, nonlinear, and humidity-dependent positive measurement bias of up to + (1.0 ± 0.2) nmol/mol at the maximum investigated trace-humidity volume fraction of 8.5 ppmV. This bias was not caused by spectral interference but rather by water-induced accumulation of ammonia within the optical cavity. Moreover, time-resolved measurements in the presence of trace ammonia showed that water desorption follows first-order kinetics, whereas water adsorption followed mixed-order kinetics with an apparent reaction order of 1.57 ± 0.03. Distinct hydration states of surface-bound ammonia were identified, whereas under dry conditions and with increasing amounts of ammonia, enhanced surface adhesion through intermolecular clustering was observed. In addition, the presence of ammonium species within the sorption layer was indirectly confirmed by our experiments. In conclusion, we provide a deeper insight into trace-level ammonia–water interactions and establish a framework for optimizing methodologies, particularly for (ultra)long-path optical gas measurement systems. KW - Ammonia KW - Hydrogen KW - OF-CEAS KW - Humidity KW - Surface Interactions KW - Adsorption PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-643627 DO - https://doi.org/10.1021/acsmeasuresciau.5c00105 SN - 2694-250X SP - 1 EP - 15 PB - American Chemical Society (ACS) AN - OPUS4-64362 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Systems With Cryogenic Liquefied Gases In Fire-Incidents N2 - The volumetric energy density of a gas can be increased by liquefaction, which occurs when the gas is cooled below the saturation point. Liquefied gases of great importance to the energy transition are Liquefied Hydrogen (LH2) and Liquefied Natural Gas (LNG), which can be liquefied at temperatures below 160°C. Systems for storing these gases typically must be overpressure resistant and require thermal super insulations (TSI) to hold cryogenic conditions and minimize boil-off losses from evaporation. TSI with vacuum and MLI or perlites are suitable for many applications involving LNG and LH2. Such systems are typically double-walled structures where the inner wall is in contact with the cryogenic liquefied gas. MLI or perlites are located in the gap between the inner and the outer wall, that is kept under vacuum conditions. This combination of insulations strongly reduces the heat transfer between the environment and the cryogenic liquefied gas. From an economic point of view the systems are well sophisticated. However, knowledge of the behavior of this kind of systems in a typical event such as a fire is limited, but necessary to evaluate the safety of the increasing number of applications. The objective of the research is to determine how TSI behaves at different fire temperatures during fire exposure and afterwards. Special attention is paid to changes in the heat flux, the material properties and vacuum state over time. For this purpose, thermogravimetric analysis (TGA) studies have been carried out. In addition, a test rig was developed that allows testing of TSI at temperatures up to 1000°C under realistic integration conditions and subsequent analysis of the TSI samples. In the test rig the double-wall with vacuum and MLI or perlites inside is simulated. The fire conditions are simulated on one side of the double-wall by adjustable electrical heating elements. This process allows the implementation of repeatable heat flows of up to 100 kW/m². On the other side of the double-wall, cold or cryogenic conditions are simulated with a heat exchanger through which water or the vapor of liquid nitrogen (approx. -196°C) flows. The heat exchanger is also used to determine the heat flux through the double-wall. Thus, the test rig allows thermal loading and performance analysis of TSI samples at the same time. Compared to tests with real cryogenic systems, tests with this experimental setup have the advantage that, first, the instrumentation is easier to realize, and a higher repeatability is ensured. Second, the local heat flow can be determined over time, and the sample of a TSI can be taken non-destructively and thus analyzed. Third, the tests are less risky as well as time+ and material intensive, so that more tests and variants can be investigated with the same budget. Preliminary results obtained considering several types of MLI under vacuum show that all observed typs of MLI can be damaged under strong thermal loading. The damages observed were outgassing, melting, shrinkage, cracking, lump formation, and concomitant local loss of the MLI's function as a radiation shield. However, the study also shows that a damage does not always have an extreme effect on the insulating performance. T2 - IMECE2022 CY - Columbus, Ohio, USA DA - 30.10.2022 KW - LH2 KW - LNG KW - Safety KW - Insulation KW - Tank PY - 2022 AN - OPUS4-56445 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Safety and security challenges in the transformation of the future energy supply N2 - For a sustainable decarbonization of the energy supply in Germany and Europe, a long-established supply system must be gradually transformed without fundamentally jeopardizing the energy supply. This transformation faces numerous challenges in the areas of safety and security including natural hazards. A safe, reliable, decarbonized energy supply requires diversification and a combination of different climate-friendly energy carriers and storage systems that are tailored to the specific requirements of industry, households and transportation. However, each energy carrier must be specifically assessed in terms of safety regarding its production, storage, transport and use. Relevant safety aspects arise from the scale at which energy carriers such as hydrogen and ammonia, but also electrical energy storage systems, must be handled. Suitable transport and storage infrastructure must be established for each energy carrier and storage facility, leading to extreme safety, technological and regulatory challenges. Central energy supplies are categorized as critical infrastructure. In the context of geopolitical conflicts, they are increasingly becoming the focus of digital or analog attacks by third parties, particularly with the aim of unsettling the respective population. The digitalization and automation of energy systems increases their vulnerability to such attacks. Geopolitical conflicts also lead to problems with the availability of raw materials and energy carriers. Also in this context, greater focus must be placed on diversification and resilience concepts. For the energy transition to succeed, traditional safety and security concepts must be interdisciplinary integrated with new aspects of resilience and crisis prevention. These concepts must be continuously developed to avoid outdated and expensive solutions. At the same time, it is reasonable to assume that the nature of threats will change more rapidly than in the past. The presentation will highlight key challenges associated with the widespread introduction of various energy carriers and storage technologies. It covers a wide range of topics, from safety-related and material-related issues to infrastructural and digital requirements as well as to aspects of security. T2 - PEMT 2025 - Annual Meeting of Process Engineering and Materials Technology CY - Frankfurt, Germany DA - 10.11.2025 KW - Safety KW - Security KW - Challenges PY - 2025 AN - OPUS4-64643 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nattuveettil, Keerthana A1 - Brunner, Nanine A1 - Tiebe, Carlo A1 - Thomas, Marcus A1 - Melzer, Michael A1 - Bartholmai, Matthias A1 - Johann, Sergej A1 - Neumann, Patrick P. T1 - Digital approach of certification in Quality Infrastructure N2 - QI-Digital is a joined project aiming at digitalising Quality Infrastructure (QI) processes involving standardization, conformity assessment, accreditation, metrology, and market surveillance [1]. Federal institute of material research and testing (BAM) is working on the creation of a digital calibration certifi-cate (DCC) to achieve digital metrological traceability and conformity assessment. The utilisation of machine readable and executable DCCs in the XML format is demonstrated on an example of a tem-perature measurement at a hydrogen refueling station. The certificates will be retrieved and analysed automatically at a Process Control System or at a Digital Twin. T2 - SMSI 2023 Conference CY - Nürnberg, Germany DA - 08.05.2023 KW - Quality Infrastructure KW - Digital Certificates KW - Temperature calibration KW - Digitalisation KW - Hydrogen technology PY - 2023 DO - https://doi.org/10.5162/SMSI2023/A3.4 SP - 51 EP - 52 PB - AMA Service GmbH CY - Wunstorf AN - OPUS4-57964 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. A1 - Bock, Robert A1 - Günzel, Stephan A1 - Gesell, Stephan T1 - Monte-Carlo-Analysis of Minimum Burst Requirements for Composite Cylinders for Hydrogen Service N2 - For achieving Net Zero-aims hydrogen is an indispensable component, probably the main component. For the usage of hydrogen, a wide acceptance is necessary, which requires trust in hydrogen based on absence of major incidents resulting from a high safety level. Burst tests stand for a type of testing that is used in every test standard and regulation as one of the key issues for ensuring safety in use. The central role of burst and proof test is grown to historical reasons for steam engines and steel vessels but - with respect for composite pressure vessels (CPVs) - not due an extraordinary depth of outcomes. Its importance results from the relatively simple test process with relatively low costs and gets its importance by running of the different test variations in parallel. In relevant test und production standards (as e. g. ECE R134) the burst test is used in at least 4 different meanings. There is the burst test on a) new CPVs and some others b) for determining the residual strength subsequent to various simulations of ageing effects. Both are performed during the approval process on a pre-series. Then there is c) the batch testing during the CPVs production and finally d) the 100% proof testing, which means to stop the burst test at a certain pressure level. These different aspects of burst tests are analysed and compared with respect to its importance for the resulting safety of the populations of CPVs in service based on experienced test results and Monte-Carlo simulations. As main criterial for this the expected failure rate in a probabilistic meaning is used. This finally ends up with recommendations for relevant RC&S especially with respect to GTR 13. T2 - 9th International Conference on Hydrogen Safety CY - Online meeting DA - 21.09.2021 KW - Hydrogen KW - Burst test KW - Composite pressure vessels KW - Net zero KW - Monte-Carlo-Analysis PY - 2021 SP - 133 EP - 146 PB - IGEM AN - OPUS4-55668 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bock, Robert T1 - Bundesanstalt für Materialforschung und –prüfung - Reallabor Wasserstofftankstelle N2 - Die Bundesanstalt für Materialforschung und -prüfung (BAM) ist eine wissenschaftlich-technische Bundesoberbehörde mit Sitz in Berlin, die zum Geschäftsbereich des Bundesministeriums für Wirtschaft und Klimaschutz gehört. Unsere Hauptaufgabe besteht darin, durch Forschung, Prüfung und Beratung zum Schutz von Mensch, Umwelt und Sachgütern beizutragen. Dies umfasst die Bewertung der Sicherheit von Materialien, Stoffen und Produkten sowie die Entwicklung von Methoden und Standards in Bereichen wie Materialwissenschaft, Werkstofftechnik und Chemie. Wir forschen und prüfen an drei Standorten in Berlin, sowie auf unserem Testgelände Technische Sicherheit in Horstwalde in Brandenburg. Hier haben wir weitreichende Möglichkeiten, Versuche im Realmaßstab durchzuführen. Besonderes Augenmerk möchten wir heute auf das Reallabor Wasserstofftankstelle richten. Diese voll digitalisierte technische Anlage, die die Wertschöpfungskette von Wasserstoff abbildet, wurde gerade eröffnet und steht nun Partnern aus Industrie und Forschung sowie kleinen mittelständischen Unternehmen oder Start-Ups zum gemeinsamen Forschen und Erproben neuer Technologie zur Verfügung. Ihre Besonderheiten umfassen z.B. eine umfassende Prozessüberwachung nach Industrie 4.0, die dafür nötige IT/OT Infrastruktur, Digitale Zwillinge auf verschiedenen Ebenen, großflächige Aufstellung und baulicher Schutz, Gas-Probenahmestellen auf dem Weg durch die Anlage und H2-Sensornetzwerke zur frühzeitigen Erfassung und Ortung von Leckagen. T2 - Wasserstoffforum Lausitz CY - Senftenberg, Germany DA - 03.11.2025 KW - Wasserstoff KW - Reallabor KW - TTS PY - 2025 AN - OPUS4-64697 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schaad, C. T1 - A Framework for Transforming Process Control System Data from a Hydrogen Fueling Station into HyCReD Data N2 - Reliability data for hydrogen infrastructure components is essential for developing Quantitative Risk Assessment (QRA) for these technologies, which in turn is necessary for a safer deployment and expansion of the hydrogen market. However, there is currently a lack of hydrogen component reliability data available for these systems, thus limiting the usefulness of insights obtained from these QRA. The Hydrogen Component Reliability Database (HyCReD) has been proposed as a tool for reliability data collection and as a source for future QRAs. In this paper, we develop a digital tool that automatically processes data coming from Process Control System (PCS) in a hydrogen fueling station, detects the relevant failure events for hydrogen systems during its operation, and then logs the event information into HyCReD. To build this tool, we first categorized the station components in hydrogen service, their specific failure modes, and the specific failure mechanisms that are relevant to a QRA. Then, we identified the data available in the station PCS and the methods available for diagnosing the relevant failure events. The resulting tool is divided into three steps: (1) PCS data collection through an API, (2) data analysis for the detection and diagnosis of new failure events, and (3) logging that event into HyCReD. Finally, we discuss the potential for expanding the detection and diagnosis to more complex failure modes present in a hydrogen fueling station. This digital tool is set for implementation and validation on an experimental hydrogen fueling site. The goal for this digital tool is to be applicable to every kind of hydrogen fueling station and to be extendable to similar hydrogen technologies. T2 - 35th European Safety and Reliability Conference (ESREL2025) and the 33rd Society for Risk Analysis Europe Conference (SRA-E 2025) CY - Stavanger, Norway DA - 15.06.2025 KW - Reliability data KW - Hydrogen safety KW - HyCReD KW - Hydrogen Component Reliability Database KW - Hydrogen fueling station KW - Hydrogen refuelling station KW - HRS PY - 2025 AN - OPUS4-63533 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Second life für E-Akkus N2 - Um die Nachhaltigkeit von Lithiumbatterien zu gewährleisten, kommt neben dem Recycling der Rohstoffe auch eine Weiternutzung von für die Erstanwendung nicht mehr ausreichend leistungsstarken Batterien aus der Erstanwendung in Frage. Dabei sind auch Sicherheitsaspekte zu beachten. T2 - Berlin Science Week 2021 CY - Online meeting DA - 10.11.21 KW - Lithium Batterien KW - Recycling KW - Second Life KW - State of Safety PY - 2021 AN - OPUS4-54178 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tiebe, Carlo A1 - Bayat, Mehmet E. T1 - Sensorvalidierungen für die Sicherheit und Prozesskontrolle entlang der Wasserstoffwertschöpfungskette N2 - Die Nutzung von Sensortechnologien, insbesondere zur Gasdetektion von Wasserstoff, ist essenziell für die Sicherheit und Prozesskontrolle von Wasserstofftechnologien. Anwendungen umfassen Sicherheitsüberwachung, Leckdetektion und Prozesskontrolle. Ziel ist die frühzeitige Erkennung freigesetzten Wasserstoffs und die Bestimmung des Wasserstoff-Luftverhältnisses. Dies dient der Gefahrenprävention und der Einleitung geeigneter Maßnahmen, z. B. Alarme. Als wichtiger Prozessschritt im Sicherheits- bzw. Qualitätsmanagement zählt auch eine präzise Charakterisierung von Wasserstoffanteilen in Luft bzw. im Prozessstrom. unterstützt die frühzeitige Schadensdetektion und erhöht die Systemsicherheit. KW - Wasserstoff KW - Sensor KW - Validierung KW - Referenzmaterial KW - Referenzverfahren KW - Sensoren KW - Gaschromatographie KW - GC PY - 2025 VL - 166 IS - 9 SP - 58 EP - 63 PB - Vulkan-Verlag GmbH CY - Essen AN - OPUS4-64119 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bayat, Mehmet A1 - Kipphardt, Heinrich A1 - Tiebe, Carlo A1 - Engelhard, Carsten T1 - Effect of Trace Humidity on Trace Ammonia Quantification N2 - Hydrogen is receiving growing attention as a promising medium for energy storage and transportation. Proton exchange membrane (PEM) fuel cells are a key technology for energy conversion from hydrogen. However, high purity hydrogen is required for this technology, as described in standards such as ISO 14687:2019. A critical impurity that impairs PEM efficiency is ammonia, for which a limit value of 100 nmol/mol applies. In addition, the maximum amount of humidity is specified with 5 µmol/mol. The presence of humidity in hydrogen at levels up to 50 times higher than ammonia raises the critical question of whether ammonia can still be quantified accurately in the lower nmol/mol range without interference from water. In addition, the general question arises as to whether the critical analyte, ammonia, can still be detected at all, given the expected surface effects at such amounts of trace humidity. In this work, we describe the influence of trace humidity on the surface behavior of adsorbed ammonia on stainless steel. Samples with ammonia at approximately 100 nmol/mol in hydrogen, with trace humidity levels ranging from 3 µmol/mol to 10 µmol/mol, were carefully prepared using dynamic mixing. Humidification was conducted using an advanced saturation method. These samples were investigated under atmospheric conditions using low pressure sampling Optical Feedback Cavity Enhanced Absorption Spectroscopy (OFCEAS). From the observed time-dependent signals, kinetics were determined and analyzed, yielding insights on the strength of the adsorption behavior of the analytes. T2 - ANAKON 2025 CY - Leipzig, Germany DA - 10.03.2025 KW - OF-CEAS KW - Hydrogen KW - Ammonia KW - Water KW - Humidity KW - Kinetics KW - Adsorption PY - 2025 UR - https://veranstaltungen.gdch.de/microsite/index.cfm?l=11713&sp_id=2&selSiteID=vplanner AN - OPUS4-64046 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. A1 - Bock, Robert T1 - Key points in compressed hydrogen storage N2 - This presentation highlights some key points in hydrogen safety related to compressed HYDROGEN STORAGE. It explains some needs concerning the Market ramp-up: cost and safety related aspects like Risk-control by consequence and/or frequency limitation. Other aspects are the optimization of design and test standards by using Monte-Carlo based assessments and the Generation of probabilistic data as input for risk management tools during the design type approval and periodic inspection. Further safety aspects of design and manufacturing have to be taken into account as well as aspects of operational safety with material degradation, non-destructive testing and appropriate tools for operational files. T2 - The opening of BAM hydrogen refueling station CY - Horstwalde, Germany DA - 03.07.2025 KW - Market ramp-up KW - Consequence limitation KW - Frequency limitation KW - Accoustic emission KW - Monte-Carlo PY - 2025 AN - OPUS4-63810 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -