TY - CONF A1 - Baeßler, Matthias T1 - Stability and large deformations of slender structures supported by soil materials N2 - Stabilitätsprobleme und große Deformationen schlanker, vorwiegend stahlbaulicher Strukturen sind in einigen Fällen stark von der Belastung und Stützung der Struktur durch den Baugrund abhängig. Der Vortrag verbindet Forschungsansätze zum Thema. T2 - Colloquium on Geotechnical Engineering CY - KIT Karlsruhe, Germany DA - 26.09.2019 KW - Stability Buckling soil-structure-interaction piles offshore PY - 2019 AN - OPUS4-49162 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric A1 - Szczepaniak, Mariusz A1 - Schoppa, Andre T1 - Abteilung 3 und Arbeitsbereich „Themenfeld Energie Gase" N2 - Vorstellung der Aufgaben-/Forschungs- und Prüfungsschwerpunkte des Arbeitsbereichs "Themenfeld Energie Gase" T2 - Besuch Expertengruppe der BG RCI CY - BAM Berlin, Germany DA - 15.05.2019 KW - Arbeitsbereichs "Themenfeld Energie Gase" PY - 2019 AN - OPUS4-49199 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Jan P. T1 - Ein Blick unter die Oberfläche von Windkraftanlagen durch Thermografie N2 - Rotorblätter von Windkraftanlagen sind hohen Belastungen ausgesetzt. Nach Jahren der Nutzung können Klebeverbindungen unter der Oberfläche versagen. Thermografie soll die Zustandsüberwachung während der gesamten Lebensdauer verbessern. N2 - Rotor blades of wind power generators are subject to high strains. After years of use, adhesive bonds under the surface may fail. Thermography is intended to improve condition monitoring during the entire service life. T2 - Hannover Messe 2019 CY - Hanover, Germany DA - 1.4.2019 KW - Wiederkehrende Prüfung KW - Thermografie KW - Klebeverbindungen KW - Rotorblatt KW - GFK PY - 2019 AN - OPUS4-49160 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric A1 - Kriegsmann, Andreas T1 - WP8 - RCS standardisation work N2 - Achievements and next steps within WP8 "RCS standardisation work" in the TAHYA Project. T2 - TAHYA Meeting PSB#2 CY - Saarburg, Germany DA - 11.06.2019 KW - TAHYA project PY - 2019 AN - OPUS4-49190 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric A1 - Szczepaniak, Mariusz T1 - Pressure cylinders for the transport of dangerous goods N2 - Introduction of the Department 3 and the competence and scientific focus of the working group focus area energy - gases for external visitors. T2 - Besuch einer Studentengruppe der AGH Krakau CY - BAM Berlin, Germany DA - 23.09.2019 KW - Introduction Department 3 KW - Focus area energy gases PY - 2019 AN - OPUS4-49193 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric T1 - System validation and safety aspects N2 - Overview of the achievements, issues and next steps with in TAHYA Project for WP5 T2 - TAHYA meeting PSB#2 CY - Saarburg, Germany DA - 11.06.2019 KW - TAHYA Project PY - 2019 AN - OPUS4-49188 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric A1 - Kriegsmann, Andreas A1 - Szczepaniak, Mariusz T1 - WP5 - System validation phase and safety aspects N2 - Objectives, tasks, achievements, ongoing work and next steps within WP5 in the TAHYA Project during the first 18 month T2 - TAHYA Midterm review meeting CY - Brüssel, Belgium DA - 26.10.2019 KW - TAHYA project PY - 2019 AN - OPUS4-49192 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. A1 - Saul, Herbert A1 - Wang, Bin T1 - Safety criteria for the transport of hydrogen in permanently mounted composite pressure vessels N2 - The recent growing of the net of hydrogen fuelling stations increases the demands to transport compressed hydrogen on road by batterie vehicles or tube-trailers, both in composite pressure vessels. As transport regulation the ADR is applicable in Europe and adjoined regions and used for national transport in EU. This regulation provides requirements based on the burst pressure of each individual pressure vessel, regardless the capabilities of the transported hydrogen and relevant consequences resulting from worst case scenarios. In 2012, BAM (German Federal Institute for Materials Research and Testing) introduced consequence-dependent requirements and established them in national requirements concerning the “UN service life checks” etc. to consider the transported volume and pressure of gases. However, this results in a stringent requirement in case of using large pressure vessels (so called “tubes”) on vehicles. In the studies presented here, the safety measures for hydrogen road transport are identified and reviewed through some safety measures from some countries like Japan, USA and China. Subsequently, the failure consequences of using trailers, the related risks and chances are evaluated. Finally, a chance-related risk criterion is suggested to add into regulations and consequently to be defined as safety goal in standards for hydrogen transport vehicles and consequently for mounted pressure vessels. T2 - ICHS International Conference on Hydrogen Safety) 2019 CY - Adelaide, Australia DA - 24.09.2019 KW - pressure-volume product KW - probabilistic approach KW - hydrogen transport KW - risk limit KW - F-N-diagram KW - maximum acceptable consequence KW - chance-risk analysis KW - specific risk value PY - 2019 SP - 104-01 EP - 104-15 PB - International Association for Hydrogen Safety (HySafe) CY - Adelaide AN - OPUS4-50124 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wang, Bin A1 - Mair, Georg W. A1 - Gesell, Stephan T1 - Determination of Distribution Function used in MCS on Safety Analysis of Hydrogen Pressure Vessel N2 - The test data of static burst strength and load cycle strength of composite pressure vessels are often described by GAUSSian normal or WEIBULL distribution function to perform safety analyses. The goodness of assumed distribution function plays a significant role in the inferential statistics to predict the population properties by using limited test data. Often, GAUSSian and WEIBULL probability nets are empirical methods used to validate the distribution function; Anderson-Darling and Kolmogorov-Smirnov tests are the mostly favorable approaches for Goodness of Fit. However, the different approaches used to determine the parameters of distribution function lead mostly to different conclusions for safety assessments. In this study, six different methods are investigated to show the variations on the rates for accepting the composite pressure vessels according to GTR No. 13 life test procedure. The six methods are: a) Norm-Log based method, b) Least squares regression, c) Weighted least squares regression, d) A linear approach based on good linear unbiased estimators, e) Maximum likelihood estimation and f) The method of moments estimation. In addition, various approaches of ranking function are considered. In the study, Monte Carlo simulations are conducted to generate basic populations based on the distribution functions which are determined using different methods. Then the samples are extracted randomly from a population and evaluated to obtain acceptance rate. Here, the “populations” and “samples” are corresponding to the burst strength or load cycle strength of the pressure vessels made from composite material and a plastic liner (type 4) for the storage of hydrogen. To the end, the results are discussed, and the best reliable methods are proposed. T2 - ICHS International Conference on Hydrogen Safety) 2019 CY - Adelaide, Australia DA - 24.09.2019 KW - Monte-Carlo Simulation KW - Distribution function KW - Weibull Distribution PY - 2019 SP - 103-1 EP - 103-16 AN - OPUS4-50383 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. A1 - Gesell, Stephan T1 - Betriebsfestigkeit von Composite-Wasserstoffspeichern Erster Ansatz zur Simulation der Auswirkung der erstmaligen Prüfung N2 - Druckbehälter werden vor ihrer Inbetriebnahme obligatorisch einer hydraulischen Prüfung bis zum sog. Prüfdruck belastet. Damit sollen fehlerhaft gefertigte Individuen erkannt und ausgesondert werden. Mit dieser Prüfung werden aber auch diejenigen Einzelbehälter ausgesondert, die ohne einem nachvollziehbaren Fertigungsfehler, nur auf Basis der statistischen Streuung ggf. eine Festigkeit unterhalb des Prüfdrucks aufweisen. Da der Prüfdruck im Fall der Wasserstoffspeicher mindestens 20% über dem maximal zulässigem Betriebsdruck liegt, wäre damit ein Versagen im Betrieb ausgenommen, gäbe es die verschiedenen Alterungs- bzw. Ermüdungseffekt nicht. Um den Einfluss der erstmaligen Prüfung auf eine angenommene ausfallfreie Zeit bewerten zu können, wird hier die Alterung und die erstmalige Prüfung in Kombination analysiert. Hierzu wird auf Basis der Restfestigkeitsdaten aus einer umfangreichen Prüfkampagne ein Ansatz für die Beschreibung der Alterung ermittelt und auf andere Lastzustände übertragen. So kann für das Baumuster, das der o.g. Prüfkampagne zugrunde lag, mithilfe einer Monte-Carlo-Simulation gezeigt werden, dass mindestens 10.000 LW vor einem ersten Alterungsversagen mit 1 aus 1 Mio. In Abhängigkeit der Anzahl der Individuen, die bei der erstmaligen Prüfung versagen, und der Streuung der gesamten Population, kann diese Mindestfestigkeit auf realistisch 50.000 Lastwechsel steigen. Damit ist gezeigt, dass aufgrund der erstmaligen Prüfung eine Mindestfestigkeit erzeugt wird, die stark vom Alterungsverhalten abhängt. Im Ergebnis heißt dies, dass in den Vorschriften aktuell die Bedeutung des Mindestberstdrucks in der Baumusterprüfung überschätzt und die möglichst betriebsbegleitende Erfassung der Alterung unterschätzt sind. T2 - 29. Fachtagung Technische Zuverlässigkeit 2019 CY - Nürtingen, Germany DA - 07.05.2019 KW - Alterung KW - Berstdruck KW - Streuung KW - Degradation KW - statistische Auswertung KW - ausfgallfreie Lastwechsel PY - 2019 SN - 978-3-18-092345-1 SN - 0083-5560 SP - 223 EP - 234 PB - VDI-Verlag GmbH CY - Düsseldorf AN - OPUS4-50181 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas A1 - Scheidemann, Robert A1 - Komann, Steffen A1 - Ballheimer, Viktor A1 - Wille, Frank T1 - Package testing of a dual purpose cask for SNF from German research reactors N2 - A new dual purpose cask design was developed for the safe transport and interim storage of spent fuel elements of German research reactors. In the framework of the safety assessment within the licensing procedure the Bundesanstalt für Materialforschung und –prüfung (BAM) as competent authority performed a series of drop tests according to the IAEA-Regulations [1]. The package consists of a cylindrical thick-walled ductile cast iron cask body closed by a double lid system with metallic seals. A lid and bottom sided impact limiter consisting of a wood/steel construction limit the mechanical impact loading. The full-scale test specimen was equipped with a basket and assembled with dummy-fuel elements. The package and test specimen, respectively have a total mass of approximately 24 metric tons. The mechanical test program included three 9m free drop tests, in horizontal, vertical and oblique cask orientation onto the lid system. Additionally, a 1m-puncture drop test followed the horizontal drop test to consider an IAEA-test sequence. The horizontal and vertical drop tests were performed at a temperature of minus 40°C. During the oblique drop test the upper impact limiter was heated to +80°C. The tests were conducted onto an unyielding target, fulfilling the requirements of the IAEA regulations [1]. The test specimen was considerably instrumented with strain gauges and accelerometers. Transient strains at selected locations of the inner and outer container walls, of the primary and secondary lid, as well as of the corresponding lid bolts were measured during the drop tests. Furthermore, decelerations in different locations at the cask body and the lids were measured. The complex geometrical deformation of the impact limiters due to the impact were determined by optical 3d- measurements using the projected fringe method in combination with multi-image photogrammetry. Before and after the drop tests the leakage rate of the lid system was determined by helium leakage testing. The experimental results contribute to the evaluation of the package response to mechanical tests, demonstrating safety under normal and accident conditions of transport. Especially to the verification of the dynamic finiteelement model of the package used in the package design safety report [2]. The paper describes the performance of the drop tests, selected test results focusing on the lid screws and the cask body and the deformation of the impact limiters as well as impact kinematics, respectively. T2 - IHLRWM2019 CY - Knoxville, TN, USA DA - 14.04.2019 KW - Drop test KW - Package testing KW - Dual purpose cask PY - 2019 SN - 978-0-89448-761-3 VL - 2019 SP - paper 27283, 1 EP - 7 PB - ANS AN - OPUS4-50619 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -