TY - CONF A1 - Wille, Frank T1 - Transport nach Zwischenlagerung, Besonderheiten des letzten Transports N2 - Transportierbarkeit von Transport- und Lagerbehältern für radioaktive Stoffe, welche nach eine längerfristigen trockenen Zwischenlagerung transportiert werden müssen. Überblick über die aktuellen Regelwerke und Richtlinien sowie die Zeitpläne für das Finden eines Endlagers für hochradioaktive Stoffe und die damit verbundene verlängerte Zwischenlagerung. Des Weiteren werden das für die verlängerte Zwischenlagerung notwendige Alterungsmanagement und die noch erforderlichen Forschungstätigkeiten vorgestellt. T2 - BGZ Fachworkshop Zwischenlagerung CY - Berlin, Germany DA - 16.11.2021 KW - Transportbehälter KW - Radioaktive Stoffe KW - Transport KW - Zwischenlagerung KW - IAEA PY - 2021 AN - OPUS4-60505 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank T1 - Verkehrsrechtliche Betrachtungen Transport- und Lagerbehälter - Wo geht die Reise hin? N2 - Transportierbarkeit von Transport- und Lagerbehältern für radioaktive Stoffe, welche nach eine längerfristigen trockenen Zwischenlagerung transportiert werden müssen. Überblick über die aktuellen Regelwerke und Richtlinien sowie die Zeitpläne für das Finden eines Endlagers für hochradioaktive Stoffe und die damit verbundene verlängerte Zwischenlagerung. Des Weiteren werden das für die verlängerte Zwischenlagerung notwendige Alterungsmanagement und die noch erforderlichen Forschungstätigkeiten vorgestellt. T2 - 10. Symposium Lagerung und Transport radioaktiver Stoffe CY - Hannover, Germany DA - 05.09.2023 KW - Transportbehälter KW - Radioaktive Stoffe KW - Transport KW - Zwischenlagerung KW - IAEA PY - 2023 AN - OPUS4-60506 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias T1 - Safety Aspects for Transport Containers with regard to Ageing and Battery Accident Scenarios N2 - In Germany, the search for a final repository for highly radioactive material is currently based on the assumption that interim storage will take considerably longer than was anticipated. At that time, authorization procedures assumed that interim storage would be brief, until the containment systems could be placed in a final repository. For today's new approvals and extensions, the IAEA (International Atomic Energy Agency) regulations for the transport of radioactive material require an assessment of all components and component groups with regard to ageing. To assess the safety requirements not only over the previously envisaged periods but also over long durations, numerous individual parts and component groups must be examined and evaluated for ageing and interactions between materials. The metal seals of a double lid sealing system, for example, are critical components that must be studied with respect to ageing. In a containment system for radioactive material, metal seals must not only undergo classic ageing, but also withstand mechanical influences and radiation over extended periods. In addition to assessments by the applicants, BAM must also independently analyze and evaluate these ageing mechanisms as part of its sovereign mandate. Another challenge in both new approvals and extensions is the assessment of transport regarding changes in the state of the art, which are not synchronously assessed in the regulations. In transporting radioactive material, a classic oil fire has been assumed in a hypothetical accident scenario from the development of the regulations to the present day. Due to the rapid development of propulsion technologies in recent years, such as battery or hydrogen-powered vehicles, investigations must be conducted in the revision process of the IAEA regulations to assess the impact of these new technologies on safety assessments. It is important for the member states of the IAEA to know whether new technologies are covered by the regulations or if changes are necessary to continue issuing international licenses. By focusing on batteries from the material to the cell to the module and the application, BAM contributes to the evaluation of batteries at every step of the chain. In addition to the safety of current and new battery technologies, BAM also endeavors to address issues of compositional trace and sustainable energy materials. T2 - MSD: Leaf CY - Livermore, CA , USA DA - 07.08.2024 KW - Safety Aspects KW - Ageing KW - Accident Scenarios KW - Battery PY - 2024 AN - OPUS4-60851 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn T1 - Surface nanotexturing by ultrashort laser pulses N2 - The presentation reviews the BAM activities in the field of surface processing by ultrashort laser pulses. A focus is laid on the generation of laser-induced periodic surface structures (LIPSS) which allow various surface functionalizations for applications in optics, tribology, liquid management, and medicine. T2 - Photonics Days Berlin Brandenburg 2022 CY - Berlin, Germany DA - 05.10.2022 KW - Laser-induced periodic surface structures (LIPSS) KW - Femtosecond laser KW - Surface functionalization PY - 2022 AN - OPUS4-55921 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Sarah-K. T1 - Second Life Verwendungen - Untersuchungen und erste Erfahrungen mit einem Ausbildungsdemonstrator N2 - Der Vortrag gibt zunächst einen Themeneinstieg in den Bereich der Second-Life-Batterien sowie rechtliche und technische Grundlagen zu Lebenszyklus und Alterung. Im Weiteren werden experimentelle Ergebnisse aus Versuchen zum thermischen Durchgehen mit Batteriemodulen aus dem BMBF-Vorhaben SEE-2L vorgestellt. Darüber hinaus wird ein eigens entwickelter Ausbildungsdemonstrators vorgestellt, welcher einen wesentlichen Baustein des Ergebnistransfers aus dem Vorhaben darstellt. T2 - Brände von Lithium-Ionen Batterien in Elektrofahrzeugen kontrollieren, eindämmen und vorbeugen CY - Essen, Germany DA - 25.04.2024 KW - Auswirkungsbetrachtungen KW - Elektrische Energiespeicher KW - Lithium-Ionen-Batterie KW - Stationäre Energiespeicher KW - Thermisches Durchgehen PY - 2024 AN - OPUS4-60187 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tschirschwitz, Rico T1 - Sicherheit stationärer elektrischer Energiespeicher – Ergebnisse aus dem Projekt SEE-2L N2 - Einleitend wird im Vortrag das Aktivitätsfeld Elektrische Energiespeicher und -umwandlung vorgestellt sowie eine kurze Einführung in die Terminologie der elektrischen Energiespeicher gegeben. Im Folgenden wird das BMBF-Vorhaben SEE-2L vorgestellt. Hier wird der Schwerpunkt auf die Entwicklung und den Aufbau eines Großversuchsstand für das thermische Durchgehen von Lithium-Batterien auf Modul- und Batterieebene gelegt. Darüber hinaus werden die Ergebnisse einer ersten Versuchsserie vorgestellt. Zum Abschluss wird ein kurzer Ausblick zu weiteren anstehenden Versuchen gegeben. T2 - Behörden-Erfahrungsaustausch Anlagensicherheit 2024 CY - Berlin, Deutschland DA - 03.06.2024 KW - Auswirkungsbetrachtungen KW - Elektrische Energiespeicher KW - Lithium-Ionen-Batterie KW - Stationäre Energiespeicher KW - Thermisches Durchgehen PY - 2024 AN - OPUS4-60190 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kromm, Arne T1 - Möglichkeiten zur Optimierung von schweißbedingten Beanspruchungen durch Einsatz von LTT-Zusatzwerkstoffen N2 - Der Vortrag gibt einen Überblick zum Thema Low Transformation Temperature (LTT) Zusatzwerkstoffe. Es wird gezeigt, wie mit einem Experiment unter Nutzung von Sychrotronstrahlung das Phänomen der Umwandlungsplastizität untersucht werden kann. T2 - 12. Vollversammlung des SFB 1120: Summer School 2024 CY - Steinfeld (Kall), Germany DA - 11.06.2024 KW - Eigenspannungen KW - LTT-Zusatzwerkstoffe KW - Hochfester Stahl PY - 2024 AN - OPUS4-60259 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kromm, Arne T1 - Best practice: How to work with a mobile diffractometer N2 - Beginning with a general overview about resdiual stress determination by X-ray diffraction, the presentation is focussing on some does and dont's when working with a portable diffractometer. T2 - European Conference on Residual Stresses 11 - Tutorial 1: Residual stresses in additive manufacturing CY - Prague, Czech Republic DA - 03.06.2024 KW - Residual stress KW - X-ray diffraction PY - 2024 AN - OPUS4-60287 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nietzke, Jonathan T1 - H2HohlZug: Standardisation of a New, Cost-effective Method for Material Characterisation for the Hydrogen Economy N2 - The feasibility of the method for slow strain tensile tests has been demonstrated in several studies, leading to the establishment of the ISO/TC 164/SC 1/WG 9 ISO committee for its standardisation. Questions have emerged during this process, that currently prevent the method from being standardised for hydrogen testing. These questions relate to specimen geometry, specimen manufacturing and gas quality and are being systematically addressed in the TransHyDE-H2HohlZug project. T2 - TrasnsHyDE Abschlusskonferenz CY - Berlin, Germany DA - 25.03.2025 KW - Hydrogen KW - Hydrogen Embrittlement KW - High-Pressure Gaseous Gas KW - Hollow Specimen Technique KW - TransHyDE KW - H2HohlZug PY - 2025 AN - OPUS4-62823 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chaudhuri, Somsubhro A1 - Junker, Birgit T1 - Infrared thermography as an inspection tool for wind turbine rotor blades N2 - With the rapid expansion of wind turbine construction, rotor blades have increasingly been identified as a primary cause of turbine downtime and failure. This has led to a growing demand for inspection technologies through which energy production losses can be minimised—particularly in comparison to conventional methods such as rope-access inspections—and through which sub-surface blade conditions can be assessed to detect damage or failure in advance. Infrared thermography has been considered as a promising non-contact, full-field inspection method that can be applied to rotor blades in both operational and idle states. In this presentation, delivered at BladesEurope 2025, the physical mechanisms that give rise to thermal contrast during thermographic inspection were explained, as this contrast enables the detection and visualisation of structural features. Results obtained from a collaborative project between BAM and Statkraft Norway were presented, followed by the validation of a finite element simulation through experiments conducted in a climate chamber.” T2 - BladesEurope Forum 2025 CY - Edinburgh, Scotland DA - 29.04.2025 KW - Thermography KW - Wind energy KW - Inspection KW - Windenergie anlage rotorblätte KW - Damage detection PY - 2025 AN - OPUS4-63060 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rodricks, Carol T1 - Advancing Sustainable Composites: Challenges and innovations N2 - With the increased use of carbon fibre polymer matrix composites comes the important question of their management at the end of their life cycle. Given the high costs associated with carbon fibre production, recycling carbon fibres from composite waste is a desirable source of reinforcing fibres for new applications. However, current recycling methods result in recycled carbon fibres that are short with little to no orientation which can only be used in applications requiring intermediate strength at a fraction of the potential of the continuous, aligned virgin fibres. Thus, a method to recycle fibres with their original length and orientation intact is vital to truly realising a circular economy for carbon fibre polymer composites. Our research introduces a novel hierarchical composite aimed at preserving the length and orientation of carbon fibres on recycling. Virgin carbon fibres are encapsulated in an insoluble epoxy matrix to form tapes that serve as the primary units of the hierarchical structure. The primary epoxy matrix protects the fibres from chemical and environmental elements while maintaining their permanent orientation. The primary tape units are subsequently embedded in a secondary recyclable matrix polymer to make larger composite structures. Elium, a thermoplastic that dissolves in acetone and has mechanical properties comparable to epoxy, was chosen as the secondary matrix of choice in this study. This approach aims to achieve a composite that is mechanical equivalent to thermoset composites while facilitating easy recycling with minimal impact on the fibres in the primary unit. T2 - Materials Week 2025 CY - Frankfurt am Main, Germany DA - 02.04.25 KW - Recycling KW - Carbon fibres KW - Mechanical testing KW - Polymer-matrix composites (PMCs), micromechanics KW - Elium PY - 2025 AN - OPUS4-63004 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn T1 - Laser-induced Periodic Surface Structures - Mechanisms, Applications, and unsolved Problems N2 - Laser-induced Periodic Surface Structures (LIPSS, ripples) are a universal phenomenon and can be generated in a contactless, single-step process on almost any type of solid upon irradiation with intense laser pulses. They represent a (quasi-)periodic modulation of the surface topography in the form of a linear grating and are typically formed in a “self-ordered” way in the focus of a laser beam. Thus, they are often accompanying laser material processing applications. The structural sizes of LIPSS typically range from several micrometers down to less than 100 nanometers – far beyond the optical diffraction limit – while their orientations exhibit a clear correlation with the local polarization direction of the laser radiation. From a theoretical point of view, a controversial debate has emerged during the last decades, whether LIPSS originate from electromagnetic effects (seeded already during the laser irradiation) – or whether they emerge from matter-reorganization processes (distinctly after the laser irradiation). From a practical point of view, however, LIPSS represent a simple and robust way for the nanostructuring of solids that allows creating a wide range of different surface functionalities featuring applications in optics, tribology, medicine, energy technologies, etc. While the currently available laser and scanner technology already allows surface processing rates at the m^2/min level, industrial applications of LIPSS are sometimes limited by the complex interplay between the nanoscale surface topography and the specific surface chemistry. This typically manifests in difficulties to control the processing of LIPSS and in limitations to ensure the long-term stability of the created surface functions. This presentation reviews the currently existent theories of LIPSS. A focus is laid on the historic development of the fundamental ideas behind the LIPSS, their corresponding mathematical descriptions and numerical implementations, along with a comparison and critical assessment of the different approaches. Moreover, some unsolved scientific problems related to LIPSS are identified and the pending technological limitations are discussed. Hereby, it is intended to stimulate further research and developments in the field of LIPSS for overcoming these limitations and for supporting the transfer of the LIPSS technology into industry. T2 - SPIG 2022 - 31st Summer School and International Symposium on the Physics of Ionized Gases CY - Belgrade, Serbia DA - 05.09.2022 KW - Laser-induced periodic surface structures (LIPSS) KW - Surface functionalization KW - Femtosecond laser processing PY - 2022 AN - OPUS4-55813 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Florian, Camilo T1 - Influence of oxidation in the formation and performance of laser-induced periodic surface structures N2 - The fabrication of laser-induced periodic surface structures (LIPSS) has been reported for metallic, semiconductor and dielectric materials when irradiated with linearly polarized ultrashort laser pulses. Different sets of processing parameters have been identified and extensively studied, allowing the use of LIPSS for applications in medicine, tribology and surface wetting to name a few. One important parameter that is often not considered is the laser-induced oxidation that is produced especially when oxidation prone materials are irradiated in air environment. This surface oxidation can potentially influence the final structures size, shape and orientation and modify their functionality in some specific applications. In this work, we first study the influence of the laser-induced oxidation layer on the formation of LIPSS by characterizing the response of the oxidation prone hard-coating material chromium nitride. Moreover, we employ complementary surface and depth-profiling analytic techniques to reveal morphological, chemical and structural features of different types of surface structures and LIPSS produced on titanium-based substrates. Finite-difference time-domain (FDTD) calculations finally explain how this superficial oxidation layer promotes the formation of a new type of low spatial frequency LIPSS. Also, we measure the depth-extent of the different oxides formed and demonstrate its beneficial influence for friction reduction and wear resistance applications. T2 - SPIE Photonics West Conference, Symposium "Laser-Based Micro- and Nano-Processing XVI" CY - San Francisco, CA, USA DA - 22.01.2022 KW - Laser-induced periodic surface structures (LIPSS) KW - Oxidation KW - Femtosecond laser KW - Laser processing KW - Finite-difference time-domain calculations (FDTD) PY - 2022 AN - OPUS4-54322 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias T1 - Maßgeblicher Einfluss geotechnischer Interaktionsprobleme auf den Tragwerksentwurf: Zwei spezielle Fallbeispiele N2 - Geotechnische Interaktionsprobleme können den Entwurf eines Tragwerks maßgeblich beeinflussen. Anhand zweier Fallbeispiele - dem Schotteroberbau auf Brücken im HGV und der Installation großer Monopiles - werden aktuelle Fälle aus dem Forschungsrepertoire der BAM vorgestellt. T2 - Geotechnische Seminarreihe am IBF des KIT CY - Karlsruhe, Germany DA - 23.01.2025 KW - Schotter auf Brücken im Hochgeschwindigkeitsverkehr KW - Pfahlfussbeulen KW - Beschleunigungsgrenzwert KW - Rammung KW - Monopiles PY - 2025 AN - OPUS4-62451 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - de Camargo, Andrea Simone Stucchi T1 - Luminescent multifunctional nanostructures for sensing and theranostics applications N2 - The research carried out at the Laboratory of Spectroscopy of Functional Materials at IFSC/USP, in Brazil, is focused on the synthesis and structural-property correlation of luminescent materials including rare-earth (RE) doped glasses, ceramics and hybrid host-guest materials. For the past five years, we have been particularly interested in the development of single- and multifunctional nanosystems based on core-shell upconversion nanoparticles (UCNP) associated with dyes, organometallic complexes and other organic molecules, for biophotonic and sensing applications. In these systems, we take advantage of energy transfer between the UCNPs and the molecules to either supress or enhance luminescent response. Examples include the possibility of bioimaging and photodynamic therapy of bacteria and cancer cells, simultaneous magnetothermia and thermometry, localized O2 sensing, fast detection and quantification of biological markers (e.g. kidney disease) and microorganisms. On what concerns the development of luminescent sensors - a recently started project, our aim is to develop paper-based platforms for point-of-care devices. In this presentation, an overview of our contributions for the past years and our future aims will be presented with several examples. T2 - ICL2023 - 20th International Conference on Luminescence CY - Paris, France DA - 27.08.2023 KW - Upconversion KW - Sensing KW - Theranostics KW - Nanoparticles KW - Photodynamic therapy PY - 2023 AN - OPUS4-60362 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -