TY - CONF A1 - Schröder, Nina T1 - Schweißen von hochfesten Feinkornbaustählen N2 - Das Schweißen von hochfesten Feinkornbaustählen erfordert aufgrund der Sicherstellung der Gütewerte des Grundwerkstoffes (Zähigkeit, Festigkeit) auch in der Schweißverbindung, die Einhaltung von engen Grenzen bei der Auswahl von Schweißparametern. Die Reproduzierbarkeit von beanspruchungsgerechten hochfesten Schweißverbindungen hängt vom Schweißverfahren und der damit einhergehenden komplexen Gefügeausbildung ab. Hierbei müssen hochfeste Schweißverbindungen mindestens die gleichen Festigkeitsanforderungen erfüllen wie der eingesetzte Grundwerkstoff. In diesem Vortrag werden speziell die Herausforderungen wie der Empfindlichkeit gegenüber der wasserstoffunterstützen Kaltrissbildung beim Schweißen von hochfesten Feinkornbaustählen und dem Mikrolegierungseinfluss auf die divergente Ausbildung der Wärmeeinflusszone thematisiert. T2 - Jahresmitgliederversammlung DVS BV Berlin CY - Berlin, Germany DA - 03.05.2023 KW - Herausforderungen beim Schweißen hochfester FKB KW - Wasserstoffunterstütze Kaltrissbildung KW - TEKKEN Test KW - Mikrolegierungseinfluss KW - Wärmeeinflusszone PY - 2023 AN - OPUS4-57995 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröder, Nina T1 - Mikrolegierungseinfluss beim Schweißen hochfester Feinkornbaustähle N2 - Mikrolegierungselemente, wie Nb und Ti, sind für die signifikante Festigkeitssteigerung von vergüteten, hochfesten Feinkornbaustählen mit einer Nominalstreckgrenze ≥ 690 MPa unerlässlich. Normvorgaben zur chemischen Zusam-mensetzung geben dabei nur obere Grenzwerte für die Hersteller vor. Weiterhin wirken sich bereits kleine Abwei-chungen in der Legierungsroute teilweise drastisch auf die mechanischen Eigenschaften aus. Somit wird eine adä-quate Vorhersage der Schweißeignung und der Integrität der Schweißverbindung aufgrund der variierenden Mikro-gefüge erschwert bis unmöglich. Unerwünschte Nebeneffekte sind die mögliche Erweichung der Wärmeeinflusszone (WEZ) als auch der gegenteilige Effekt der Aufhärtung. T2 - DVS BV Potsdam, Mitglieder Weiterbildungsveranstaltung CY - Groß Kreutz (Havel), Germany DA - 31.05.2023 KW - WEZ Erweichung KW - WEZ Aufhärtung KW - Mikrolegierungseinfluss KW - Schweißen von hochfesten FKB PY - 2023 AN - OPUS4-57996 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Witte, Julien A1 - Hübler, Daniela A1 - Schröpfer, Dirk A1 - Börner, Andreas A1 - Kannengießer, Thomas ED - Hanke, S. T1 - Wear behavior of innovative niobium carbide cutting tools in ultrasonic-assisted finishing milling N2 - The resources of niobium exceed the ones of tungsten by an order of magnitude. With 92%, Brazil is today the main global producer of niobium. Hence, niobium carbides (NbC) are a sustainable and economic alternative to conventionally used cutting materials, especially tungsten carbides (WC). Moreover, NbC can be used in Ni alloy matrix and thus offer significant advantages by substituting WC in Co matrix as cutting materials in terms of health risks and raw material price and supply risk. Based on recent studies which found an increased performance of NbC compared to WC cutting tools in machining higher strength steels, the composition NbC12Ni4Mo4VC was chosen for finish machining of a high-strength steel S960QL in this study. The experiments were carried out on an ultrasonic-assisted 5-axis milling machine using NbC tools specially made to benchmark them with commercially available coated WC cutting inserts. In addition, the influence of a coating system for the NbC inserts is tested and evaluated for its performance in the cutting process. Tool wear and cutting force analyses are implied to identify optimal parameter combinations as well as tool properties for the novel NbC tool. Together with the oscillation of ultrasonic-assisted milling, the loads on the component surface and the tool can be reduced and the wear behavior of the novel NbC tool can be refined. These milling tests are accompanied by standardized wear tests, i.e., pin-on-disc, between the aforementioned material combinations, and the results are correlated with each other. Finally, the behavior when using hard-to-cut materials such as Ni alloys, or innovative materials such as iron aluminide is also being tested, as these are constantly in the focus of machining optimization. With this strategy, comprehensive knowledge is achievable for future efficient application of NbC for milling tools, which have already been researched for decades using WC. T2 - 24th International Conference on Wear of Materials CY - Banff, Canada DA - 16.04.2023 KW - Niobium carbide KW - Cutting tool KW - Ultrasonic-assisted milling KW - Tool wear PY - 2023 DO - https://doi.org/10.1016/j.wear.2023.204722 SN - 0043-1648 VL - 522 SP - 1 EP - 7 PB - Elsevier B.V. AN - OPUS4-57561 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröder, Nina T1 - Influence of Microalloying on Precipitation Behavior and Notched Impact Strength of Welded High Strength Structural Steels N2 - Microalloying elements, such as Nb and Ti, are essential for significantly increasing the strength of quenched and tempered, high-strength structural steels with a nominal yield strength ≥ 690 MPa and their welded joints. The standard specifications (e.g., EN 10025-6) for the chemical composition are only tolerated limit contents within which the steel manufacturers operate. The standard composition, however, says nothing per se about the properties of the material. Even small deviations in the alloy route can have a drastic effect on the mechanical properties. This makes it difficult or even impossible to adequately predict the weldability and integrity of the welded joint. An undesirable side effect is the possible softening of the heat-affected zone (HAZ), as well as the opposite hardening.Mechanical-technological investigations of the notched impact strength confirm the results of the simulation regarding the development of different microalloy routes in the welded state. From this, the influence of the heat effect of welding on the microstructure formation in the HAZ and the corresponding mechanical properties can be described qualitatively. T2 - 76th IIW Annual Assembly and International Conference on Welding and Joining CY - Singapore DA - 16.07.2023 KW - High-strength structural steel KW - Notched impact strength KW - HAZ-softening KW - Microalloying influences PY - 2023 AN - OPUS4-57997 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröder, Nina T1 - Mikrolegierungseinfluss auf das Ausscheidungsverhalten und die mechanischen Eigenschaften geschweißter hochfester Baustähle N2 - Mikrolegierungselemente, wie Nb und Ti, sind für die signifikante Festigkeitssteigerung von vergüteten, hochfesten Feinkornbaustählen mit einer Nominalstreckgrenze ≥ 690 MPa unerlässlich. Normvorgaben zur chemischen Zusammensetzung geben dabei nur obere Grenzwerte für die Hersteller vor. Weiterhin wirken sich bereits kleine Abweichungen in der Legierungsroute teilweise drastisch auf die mechanischen Eigenschaften aus. Somit wird eine adäquate Vorhersage der Schweißeignung und der Integrität der Schweißverbindung aufgrund der variierenden Mikrogefüge erschwert bis unmöglich. Unerwünschte Nebeneffekte sind die mögliche Erweichung der Wärmeeinflusszone (WEZ) als auch der gegenteilige Effekt der Aufhärtung. Vor diesem Hintergrund werden erstmals systematisch die unterschiedlichen Mikrolegierungsrouten mit variierenden Ti- und Nb-Gehalten an Versuchsschmelzen untersucht. Die Stahlgüte S690QL bildet dabei die Grundlage der chemischen Zusammensetzung sowie der entsprechenden Wärmebehandlung. Zur Untersuchung der jeweiligen Schweißeignung wurden Dreilagen-Schweißungen mittels moderner MAG-Hochleistungsschweißprozesse durchgeführt und kritische Gefügebereiche mit hoher Erweichung/Aufhärtung identifiziert. Mechanisch-technologische Untersuchungen zur Kerbschlagzähigkeit mittels Kerbschlagbiegeversuchen durchgeführt wurden, bestätigen dabei die Ergebnisse der thermodynamischen Simulation bezüglich des Ausscheidungsverhaltens während der Temperatur-Zeit Schweißzyklen. Daraus lässt sich der Einfluss der Wärmeeinwirkung beim Schweißen auf die Gefügeausbildung in der WEZ und der korrespondierenden mechanischen Eigenschaften qualitativ beschreiben. T2 - DVS CONGRESS 2023 CY - Essen, Germany DA - 11.09.2023 KW - WEZ-Erweichung KW - Digital Image Correlation KW - Mikrolegierungseinfluss KW - Hochfester Feinkornbaustahl KW - Kerbschlagzähigkeit PY - 2023 AN - OPUS4-58354 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröder, Nina A1 - Kadoke, Daniel A1 - Kruse, Julius T1 - Investigation of the local strain behavior by digital image correlation and transverse tensile tests on welded differently microalloyed high strength structural steel N2 - Der Einsatz von hochfesten niedriglegierten Stählen (HSLA) ist in vielen Industriesektoren, wie dem allgemeinen Bauwesen, Offshore Strukturen, Mobilkranbau usw. unumgänglich geworden. Die steigende Nachfrage an Stählen mit einer hohen Festigkeit und gleichzeitig hervorragenden Zähigkeit stellt ein ökonomisches und ökologisches Potential dieser Stähle in Vordergrund. Aktuell gültige Normvorgaben (EN ISO 10025-6) geben den Stahlherstellern Vorgaben bezüglich der chemischen Zusammensetzung, um die geforderten mechanischen Eigenschaften erreichen zu können. Die Legierungsrouten variieren jedoch von Hersteller zu Hersteller. In Betracht der Schweißeignung dieser Stähle zeigt sich das Problem, dass diese bereits bei geringen Nb- und Ti-Mikrolegierungsunterschieden im Grundwerkstoff ein divergentes metallurgisches Verhalten in der Wärmeeinflusszone (WEZ) aufweisen. In diesem Vortrag werden die schweiß-metallurgischen Unterschiede zwischen verschieden mikrolegiertem hochfestem Feinkornbaustahl S690QL thematisiert. Zur Prüfung der Schweißnahtfestigkeit wurden mittels eines instrumentierten DIC (ARAMIS) Systems Querzugversuche an Schweiß-Querflachzugproben durchgeführt. T2 - AJP 2023 3rd International Conference on Advanced Joining Processes CY - Braga, Portugal DA - 19.10.2023 KW - WEZ-Erweichung KW - Hochfester Feinkornbaustahl KW - Digital Image Correlation KW - Querzugversuch KW - Mikrolegierungseinfluss PY - 2023 AN - OPUS4-58721 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Giese, Marcel T1 - Investigation of the influence of PWHT heating rate and global stress conditions on the stress relief cracking mechanism of CrMoV steel SAW joints N2 - This presentation summarizes the latest research results of the influence of the post weld heat treatment (PWHT) rate and the global mechanical stress conditions on the stress relief cracking (SRC) susceptibility of low-alloyed and creep-resistant CrMoV steel submerged arc weld joints. It was found that a certain effect of very low heating rates could be confirmed. In addition, the interlinking of SRC susceptibility increasing effects during the PWHT and the ex-post indentification in metallographic cross-section via microstructure characterization is very complex. T2 - IIW Intermediate meeting of Commission II-A CY - Garching, Germany DA - 06.03.2023 KW - Creep-resistant steel KW - Submerged arc welding KW - Stress relief cracking KW - Heating rate KW - Microstructure characterization PY - 2023 AN - OPUS4-57116 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas T1 - Full-scale drop testing with a heavy-weight package for radioactive waste N2 - Packages for the transport of radioactive materials shall fulfil the requirements of the IAEA regulations for the safe transport. The requirements define mechanical and thermal test conditions including criteria ensuring the package design’s ability to withstand severe accidents and provide a high level of technical safety. Different methods can be used for safety demonstration showing compliance with the regulations. The central part of a safety demonstration which is presented in this paper was a comprehensive drop test program with a full-scale model of a transport package accompanied by pre- and post-test FE analyses. Using full-scale drop test models allow the benefit that similarity and scaling issues become a significant smaller issue, additional material investigations can be limited and analyses for transferring test results to the original package design are reduced. Additionally, experience for the future serial packaging manufacturing and handling procedures can be collected in a very early state of the design approval process. The pre-test finite element analyses derived and justified the drop test program consisting of several drop sequences with different drop orientations of the specimen. The performance and the results of the drop test sequences shows the manageability and the advantage e.g., in view of the direct availability of test results for the package licensing. On the other hand, the drop test performance shows the difficulties during handling and the need for additional equipment during preparation of the specimen. The package presented was intended for the transport and storage of compacted radioactive waste from reprocessing of spent nuclear fuel assemblies - designed and applied for approval by the AGC consortium. The project ended in 2021. The package design was characterized by a cask body made of a forged thick stainless-steel shell, a bolted double lid system with metallic gaskets and wood filled shock absorbers at both ends. The total mass of the entire transport package including content was 120,000 kg, the total length was about 7000 mm and the diameter approximately 3000 mm, both measures include the shock absorbers. The paper provides an insight into the performance of a full-scale drop testing campaign within the package safety evaluation and shows some selected test results. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 22) CY - Juan-Les-Pins, France DA - 11.06.2023 KW - Full-scale KW - Drop testing KW - Package KW - Radioactive waste PY - 2023 AN - OPUS4-57731 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael T1 - Component test for the assessment of hydrogen assisted cracking susceptibility of thick-walled submerged arc welded offshore steels N2 - Offshore wind turbines (OWT) are a key factor of the sustainable energy generation of tomorrow. The continuously increasing installation depths and weight of the OWTs require suitable foundation concepts like monopiles or tripods. Typically, mild steels like the S420ML are used with plate thicknesses up to several hundreds of mm causing high restraints in the weld joints. Due to the large plate thickness, submerged arc welding (SAW) with multiple wires is the state-of-the-art welding procedure. As a result of the very high stiffness of the construction, a certain susceptibility for time-delayed hydrogen-assisted cracking (HAC) may occur. The evaluation of crack susceptibility is very complex due to the component size and stiffness of real offshore structures. For this purpose, a near-component test geometry was developed to transfer the real stiffness conditions to laboratory (i.e., workshop) scale. The investigated mock-up, weighing 350 kg, comprised heavy plates (thickness 50 mm, seam length 1,000 m) joined by a 22-pass submerged arc weld. Additional stiffeners simulated the effect of high restraint or shrinkage restraint of the weld. Extreme scenarios of hydrogen absorption during welding were simulated via the use of welding fluxes in dry (HD < 5 ml/100g Fe) and moisture condition (HD > 15 ml/100g Fe). The residual stresses were determined by a robot X-ray diffractometer. Areas of critical tensile residual stress (at the level of the yield strength) were found in the weld metal and heat affected zone. To identify possible delayed cracking, the welds were tested by phased array ultrasonic testing (PAUT) after 48 h. Summarized, no significant occurrence of HAC was detected, indicating the high crack resistance of the welded joint, i.e., a suitable combination of base material, welding consumable and welding parameters. T2 - AJP 2023: 3rd International Conference on Advanced Joining Processes 2023 CY - Braga, Portugal DA - 19.10.2023 KW - Hydrogen assisted cracking KW - Submerged arc welding KW - Component test KW - NDT KW - Waiting time PY - 2023 AN - OPUS4-58672 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Popiela, Bartosz T1 - Influence of manufacturing process related residual stresses in wound composite material on the operational safety of H2 pressure vessels: PhD Topic Introduction N2 - Short introduction of the PhD Topic 5 in the BTU-BAM Graduate School "Trustworthy Hydrogen". Description of the objectives, deliverables and expected added value of the thesis. T2 - Introduction Week - BTU-BAM Graduate School "Trustworthy Hydrogen" CY - Berlin, Germany DA - 16.01.2023 KW - Residual stress KW - Composite KW - Pressure vessel KW - Hydrogen PY - 2023 AN - OPUS4-56882 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chierici, Andrea A1 - Ciolini, Riccardo A1 - Lo Frano, Rosa A1 - D’Onofrio, Antonio A1 - Sabbarese, Carlo A1 - Pandalone, Antonio A1 - Romoli, Mauro A1 - di Meo, Paolo A1 - Finocchiaro, Paolo A1 - Conti, Enrico A1 - Gonella, Franco A1 - Andreetto, Paolo A1 - Checchia, Paolo A1 - Niederleithinger, Ernst A1 - d’Errico, Francesco T1 - Innovative Non-Destructive Techniques for Radioactive Waste Packages Monitoring N2 - A monitoring and surveillance system is a mandatory element to ensure that a radioactive waste disposal facility provides and meets the required level of safety during both its operational and closure periods. In this study an innovative approach for the identification and monitoring of the structural integrity of stored radioactive drums is presented. The activities were carried out in the context of the European Project PREDIS, whose goal is the development of a robust and reliable sensing technology for monitoring and long-term storage of radioactive waste packaging systems. Specifically, the focus was set on the development of innovative and smart sensor technologies, non-destructive examination tools, and/or devices capable to improve the safety of the storage by minimizing the number of interventions of cemented waste packages. Both conventional and innovative techniques, such as muon-tomography, SiLiF neutron and SciFi gamma detection, or contactless and smart radio transceiver technology provided with radiation monitoring sensors, have been considered and adapted for the use under repository conditions. Indeed, gamma and neutron detection techniques exploit the radiological information coming from inside the drums, while imaging techniques proved to be effective in spotting high density objects embedded inside the concrete: together, they allow to improve safety and security and can provide an early alert on behavioral changes hinting at anomalies in the drums. T2 - ASME 2023 International Conference on Environmental Remediation and Radioactive Waste Management CY - Stuttgart, Germany DA - 03.10.2023 KW - Radioactive waste KW - Waste packages KW - Radiation monitoring KW - Muon tomography KW - Integrity testing PY - 2023 SN - 978-0-7918-8753-0 DO - https://doi.org/10.1115/ICEM2023-110990 SP - 1 EP - 10 PB - American Society of Mechanical Engineers AN - OPUS4-60218 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. A1 - Günzel, Stephan T1 - Der sichere Wasserstofftransport - Eine Rechtsänderung in der Vorschau N2 - Das Bundesverkehrsministerium hat seit 2008 in drei Stufen jeweils auf Vorschlag der BAM einen Antrag zur Einführung bzw. Regulierung von Bergungsdruckgefäßen bei den Vereinten Nationen eingebracht. Die Anträge führten jeweils nach der Delegation in eine Arbeitsgruppe unter der Leitung des Vortragenden zu neuen Vorschriften im internationalen Gefahrguttransportrecht. Zuletzt hat das UN-Subcommittee der Experten für den Transport gefährlicher Güter der Einführung einer Druck-Volumen-Begrenzung für Druckgefäße zugestimmt. Mit dieser Begrenzung wurde die bisherige Volumenbegrenzung für Bergungsdruckgefäße ersetzt, wodurch nun das Spektrum der Bergungsdruckgefäße gestaltet werden kann, das notwendig wäre, um defekte Druckgefäße transportieren zu können. Das zentrale Kriterium für die Begrenzung des Druck-Volumen-Produktes (pV) fand bereits in den Landverkehrsvorschriften ADR/RID bis zu ihrer Neustrukturierung auch als Konsequenzmaß Verwendung. Damit soll sichergestellt werden, dass sich aus Wasserstofftransporten in Druckgefäßen keine Konsequenz entwickeln kann, die nach den Kriterien für stationäre Anlagen, einer Katastrophe gleichkommen würde. Hierzu hatte eine Arbeitsgruppe der Vereinten Nationen seit 2020 auf Vorschlag der BAM eine Kette aufeinander aufbauende Kriterien diskutiert, die im Vortrag vorgestellt werden: Einfluss der Druckwellen auf den menschlichen Körper (ohne Splitterwirkung oder Umsetzung der chemischen Energie) – Zusammenhang von Druckwelle und Fläche – Druckwellenberechnung – Bevölkerungsdichte – Grenzwerte für eine Katastrophe – resultierendes pV-Produkt. Das Ergebnis wurde mit herausragenden Großunfällen und Katastrophen aus dem Gefahrguttransport und Gefahrstoffbereich verglichen. Außerdem wurden noch die Effekte des Temperatureinflusses auf den maximalen Betriebsdruck diskutiert. Zuletzt wurde bei den UN darauf hingewiesen, dass mit Blick auf die Auswirkungsbetrachtung der Wassersoff das Gas mit den geringsten Konsequenzen bei gegeben Druk-Volumen-Produkt ist, was zu restriktiveren Obergrenzen für z.B. Erdgas führen könnte. Als letzter Punkt im Vortrag wird erläutert, dass in den kommenden UN-Sitzungen über nachfolgende Änderungen im Recht, wie z.B. der Kennzeichnung des pV-Produktes, diskutiert werden wird. Außerdem muss ein neuer Einstieg für die bei ISO in der Normung befindliche Umschließungen mit einem größeren pV-Produkt gefunden werden, wozu aber Transportland-spezifische Risikoanalysen in Verbindung mit massiven Fahrwegsbeschränkungen zu erwarten sind. T2 - 32. Erfahrungsaustausch für Gefahrgutbeauftragte (ERFA-T) des IGV CY - Berlin, Germany DA - 08.11.2023 KW - pV-Produkt KW - Quantitative Risikoanalyse KW - Konsequenzbegrenzung KW - Katastrophe KW - Druckgefäße PY - 2023 AN - OPUS4-58832 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael T1 - Metrology for Advanced Hydrogen Storage Solutions (MefHySto) – Overviewand Tangible Results N2 - The European project MefHySto addresses the need of large-scale energy storage, which is required for a shift to renewable energy supply. The project is funded by the European Metrology Programme on Innovation and Research (EMPIR) and consists of 14 consortium partners from all over Europe (www.mefhysto.eu). It is demonstrated, how MefHySto is contributing to the EMN for Energy Gases aiming at prioritisation of the measurement gaps and challenges interacting with the EMN stakeholders. T2 - European Metrology Network Energy Gases “Measurement Solutions for Energy Gases” Workshop CY - Lisbon, Portugal DA - 21.03.2023 KW - MefHySto KW - EMPIR KW - Hydrogen Storage KW - Hydrogen Metrology KW - Hydrogen Purity KW - Geological Storage PY - 2023 AN - OPUS4-57193 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kipphardt, Heinrich T1 - Introduction to Metrology in Chemistry N2 - Measurements are an important fundament of natural science in general and of chemical analysis in particular. Metrology is the science (and art) of performing measurements. The basic concepts and terms of metrology and their practical implementation are introduced. The very special peculiarities of chemical measurements that are absent in physical measurements are discussed. T2 - 7th PhD Seminar of the German Working Group for Analytical Spectroscopy (DAAS) in the GDCh Division of Analytical Chemistry CY - Berlin, Germany DA - 15.11.2023 KW - Metrology KW - Chemical Analysis PY - 2023 AN - OPUS4-58868 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Winckelmann, Alexander T1 - How does solid microanalysis profit from innovations in EUV research N2 - Research into new sources for EUV lithography is driving advancements in experimental methods tailored for this short wavelength range. This progress enables the exploration of spectroscopic techniques aimed at monitoring electronic transitions within this energy spectrum. Laser-induced breakdown spectroscopy (LIBS) serves as a rapid tool for elemental analysis, primarily established in the UV-vis range. However, LIBS encounters challenges such as limited repeatability precision and elevated background noise resulting from continuum radiation. In parallel, laser-induced extreme UV spectroscopy (LIXS) delves into the initial stages of plasma evolution, characterized by the emergence of soft X-ray and extreme UV radiation. The method benefits from a fast timeframe and constrained plasma confinement, leading to better precision. Nevertheless, LIXS encounters convoluted spectra arising from unresolved transition arrays (UTA), particularly pronounced for heavier elements. This complexity renders conventional univariate data analysis impractical, demanding the adoption of a multivariate data analysis approach. Multiple cathode samples, each coated with varying stoichiometries of lithium nickel manganese cobalt oxide (NMC), were prepared and used for calibration purposes. Through the application of Partial Least Squares (PLS) regression, a robust correlation with an R2 value exceeding 0.97 was achieved. The LIXS technique underwent a comparative evaluation against UV-vis LIBS. Furthermore, a comparison between univariate and multivariate analysis approaches was conducted, incorporating validation through y-randomization to mitigate overfitting risks. The viability of this approach was confirmed through the testing of an NMC reference material. The results showed metrological compatibility with reference values, underscoring the potential capability of the proposed methodology. T2 - 322. PTB Seminar 2023 - VUV and EUV Metrology CY - Berlin, Germany DA - 14.11.2023 KW - Laser induced XUV spectroscopy KW - Lithium-ion batteries KW - Solid microanalysis PY - 2023 UR - https://www.euv2023.ptb.de/ AN - OPUS4-58834 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kipphardt, Heinrich T1 - MefHySto - Metrology for Advanced Hydrogen Storage Solutions N2 - An overview on the almost completed EMPIR-MefHySto-Project is given. T2 - Workshop on Green Hydrogen CY - Montevideo, Uruguay DA - 12.10.2023 KW - MefHySto KW - Hydrogen storage KW - Metrology PY - 2023 AN - OPUS4-58650 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ziel, Ruben P. A1 - Zalewska, Ewelina A1 - van der Veen, Adriaan M. H. A1 - Kipphardt, Heinrich A1 - Tuma, Dirk A1 - Esteban, Andres Rojo A1 - Fernandez Vicente, Teresa Esperanza A1 - Mace, Tatiana A1 - Sutour, Christophe A1 - Marioni, Fabrice A1 - Fükö, Judit A1 - Szücs, László A1 - Büki, Tamás A1 - Szilágyi Nagyné, Zsófia A1 - Cieciora, Dariusz A1 - Ochman, Grzegorz A1 - Romanowski, Przemysław A1 - Lis, Anna A1 - Garnuszek, Magdalena A1 - Valkova, Miroslava A1 - Ackermann, Andreas A1 - Pascale, Celine A1 - Niederhauser, Bernhard A1 - Tarhan, Tanil A1 - Boztepe, Aylin A1 - Beránek, Jan A1 - Bárta, Miroslav T1 - International comparison EURAMET.QM-K3.2019 - Automotive exhaust gases N2 - EURAMET.QM-K3.2019 was a repeat of the key comparison EURAMET.QM-K3 on the composition of automotive exhaust gases. New in EURAMET.QM-K3.2019 was the addition of the amount fraction oxygen to the programme. The key comparison reference values were obtained independently, using static gravimetry and appropriate corrections from purity analysis and are linked to those of CCQM-K3.2019. The key comparison results show equivalence between the measurement standards maintained by the participating national metrology institutes. The demonstrated equivalence can be used to underpin services related to automotive exhaust gases as well as generically through the flexible scheme ("track A"). KW - CCQM KW - Automotive gases PY - 2023 DO - https://doi.org/10.1088/0026-1394/60/1A/08030 SN - 1681-7575 VL - 60 IS - 1A SP - 1 EP - 63 PB - IOP Publishing CY - Bristol AN - OPUS4-58904 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lozano-Martín, D. A1 - Tuma, Dirk A1 - Kipphardt, Heinrich A1 - Khanipour, Peyman A1 - Chamorro, C. R. T1 - Thermodynamic characterization of the (H2 + C3H8) system significant for the hydrogen economy: Experimental (p, rho, T) determination and equation-of-state modelling N2 - For the gradual introduction of hydrogen in the energy market, the study of the properties of mixtures of hydrogen with typical components of natural gas (NG) and liquefied petroleum gas (LPG) is of great importance. This work aims to provide accurate experimental (p, rho, T) data for three hydrogen-propane mixtures with nominal compositions (amount of substance, mol/mol) of (0.95 H2 + 0.05 C3H8), (0.90 H2 + 0.10 C3H8), and (0.83 H2 + 0.17 C3H8), at temperatures of 250, 275, 300, 325, 350, and 375 K, and pressures up to 20 MPa. A single-sinker densimeter was used to determine the density of the mixtures. Experimental density data were compared to the densities calculated from two reference equations of state: the GERG-2008 and the AGA8-DC92. Relative deviations from the GERG-2008 EoS are systematically larger than those from the AGA8-DC92. They are within the ±0.5% band for the mixture with 5% of propane, but deviations are higher than 0.5% for the mixtures with 10% and 17% of propane, especially at low temperatures and high pressures. Finally, the sets of new experimental data have been processed by the application of two different statistical equations of state: the virial equation of state, through the second and third virial coefficients, B(T, x) and C(T, x), and the PC-SAFT equation of state. KW - Hydrogen-containing gas mixture KW - Density data KW - Equation of state KW - Virial coefficients PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-570056 DO - https://doi.org/10.1016/j.ijhydene.2022.11.170 SN - 0360-3199 VL - 48 IS - 23 SP - 8645 EP - 8667 PB - Elsevier B. V. CY - Amsterdam AN - OPUS4-57005 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eiben, Mario T1 - Die Aufgaben der BAM als zuständige Behörde im Gefahrgutbereich in Deutschland N2 - Die BAM ist zuständige Behörde in Deutschland für bestimmte Aufgaben im Gefahrgutbereich, die u. a. in § 8 der Gefahrgutverordnung Straße, Eisenbahn und Binnenschifffahrt (GGVSEB) und § 12 der Gefahrgutverordnung See (GGVSee) aufgeführt sind und hauptsächlich von den Abteilungen 2 und 3 wahrgenommen werden. So ist die BAM bspw. die in Deutschland für die Zulassung von Verpackungen und Tanks oder auch die Einstufung bestimmter gefährlicher Güter zuständige Stelle. Die BAM arbeitet des Weiteren als Kompetenzbehörde national und international in den entsprechenden Gremien mit und berät das BMDV in der Rechtsfortentwicklung der internationalen Vorschriften für den Gefahrguttransport. Dies geschieht u. a. durch die Mitarbeit im Ständigen Ausschuss Gefahrgutbeförderung (AGGB) des Gefahrgut-Verkehrs-Beirats beim BMDV und den zugehörigen Arbeitsgruppen, oder auch das Erstellen von Anträgen für Rechtsänderungen in den internationalen Vorschriften der Vereinten Nationen (UN) bzw. der Wirtschaftskommission für Europa der UN (UNECE) im Auftrag des BMDV. Die Beratung der betroffenen Wirtschaft und die Normungsarbeit sind weitere wichtige Themen. Die Expertise der BAM wird insbesondere durch Forschung im Gefahrgutbereich erhalten und weiter ausgebaut. Im Rahmen des Vortrags werden drei Forschungsbereiche vorgestellt, von denen zwei für die Energiewende von großer Bedeutung sind. T2 - 10. Deutsche Gefahrgut-Sicherheitstage CY - Nürburg, Germany DA - 13.09.2023 KW - Gefahrgut KW - Zuständige Behörde KW - Transport gefährlicher Güter KW - Gremienarbeit KW - Normung KW - Forschung KW - Gesetzliche Aufgaben PY - 2023 AN - OPUS4-58350 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Entwicklungen rings um Gase als Energieträger N2 - Dr. Mair erläutert, welcher Anwuchs an H2-Bedarf zu erwarten ist, wo er weltweit erzeugt werden könnte und in welcher Form auf grünem Wasserstoff basierende Energieträger transportiert werden können. Es wird deutlich, dass das Transportaufkommen von H2 erheblich anwachsen wird und dass sich alle Seiten, die Regelsetzer und die Industrie darauf vorbereiten müssen. Danach wird mit Blick auf die Normungsroadmap H2 des DIN der probabilistische Ansatz mit seinem Potenzial, Normen und Vorschriften in ihrer Wirkung zu simulieren und zu bewerten kurz vorgestellt. Der dritte Block des Vortrages beginnt mit der Definition von Sicherheit, zeigt kurz das mikromechanische Prinzip der Alterung von Composite und greift dann ein Thema auf, dass Dr. Mair bereits 2018 und 2019 in dieser Runde dargelegt hat: Der Aufwand für die klassische Wiederkehrende Prüfung ist enorm und bringt nur wenig Erkenntnis. Es werden graphisch das 5-Jahres 100%-Prooftesting, der Ansatz nach GGR 022 mit seiner zerstörend geprüften Stichprobe und der mögliche Ansatz für eine ergebnisgesteuerte Stichprobenprüfung auf ZfP-Basis miteinander verglichen. Die Unterschiede im Aufwand-zu-Nutzen-Verhältnis sind enorm. Dabei ist der aufwändigste Ansatz zudem der mit der geringsten Erkenntnistiefe. Jeder Ansatz, der von einer 100%-Prüfung in einem maximalen Zeitrahmen von 10 Jahren abweicht, also z.B. der Verzicht auf eine 100%-Prüfung während des Betriebes, würde eine Änderung des Regelwerkes erfordern, die zeitnah angestoßen werden müsste. Da es sich hierbei primär um eine Ressourcenoptimierung und nicht um eine Verbesserung der Sicherheit handelt, liegt der Ball bei den Verbänden. Als eine Idee für das Herangehen mit einer Begrenzung auf Druckgefäße, die nach der EN 17339 zulassungsfähig sind (fest montiert, H2 und nur CFK), verweist Dr. Mair auf die SV 674 in Verbindung mit 6.2.3.5.3/.4 ADR/RID. Bei dem absehbaren Anwachsen des Bestandes an H2-Batteriefahrzeugen, ist hier nicht nur ein Optimierungsaspekt, sondern auch ein Kapazitätsproblem in der wiederkehrenden Prüfung zu lösen. Es würde aber auch ein Mehrwert für die Sicherheit entstehen. T2 - 30. BAM-DIN-IGV-DVFG Treffen CY - Berlin, Germany DA - 22.02.2023 KW - Wasserstoffspeicher KW - Markthochlauf KW - Sicherheit KW - Wiederkehrende Prüfung KW - Schallemissionsanalyse PY - 2023 AN - OPUS4-57041 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -