TY - CONF A1 - Theiler, Geraldine T1 - Fretting behavior of elastomer materials in hydrogen N2 - This presentation deals with the fretting wear behavior of elastomer materials (two types of cross-linked hydrogenated acrylonitrile butadiene rubbers) against 316L steel ball in hydrogen environment. Furthermore, aging experiments were conducted for 7 days under static conditions in 100 MPa hydrogen. Fretting tests revealed the wear of the polymer decreases with increasing hydrogen pressure. After high pressure hydrogen exposure, the fretting process is characterized by increased adhesion due to elastic deformation, leading to partial slip. T2 - 63rd German Tribology Conference 2022 CY - Göttingen, Germany DA - 26.09.2022 KW - Fretting KW - Rubbers KW - Hydrogen PY - 2022 AN - OPUS4-62082 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kröll, Mirco T1 - Harmonized testing in hydrogen N2 - In this study, the tribological performance of conventional and alternative polymer compounds for compressors was investigated in gaseous hydrogen using several tribometers. The compounds used were a commercial PEEK matrix with 10 wt.% each of PTFE, graphite, and short carbon fibres (Polytron), a PPS matrix with 10 wt.% each of PTFE and graphite (MOCOM), and an experimental PA12 matrix with PTFE, chamically coupled with an oleyl alcohol, as additive (supplied by the polymer research institute IPF). For all compounds a steel counter disc (type 316L / 1.4404) with a lapped surface finish was used in a cylinder-on-disc setup. Next to the tribological performance of the polymer compounds in hydrogen atmosphere, a strong focus of the work was to compare the results obtained with different tribometer setups. The tests were carried out with three different tribometers at two institutions. The challenge to compare and harmonise equipment, procedures, test and evaluation methods was an important part of the study. This includes the determination of the wear volumes of the polymeric cylinders with different wear analysis workflows. Furthermore, selected results of the wear and the resulting change in the contact geometry were compared with an FEM simulation and an analytical model. T2 - 25th International Conference of Wear of Materials CY - Sitges, Spain DA - 14.04.2025 KW - Standardisation KW - Harmonisation KW - Hydrogen KW - Polymers KW - Wear KW - Coefficient of Friction KW - Interlaboratory comparison KW - Tribometer PY - 2025 AN - OPUS4-62992 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine T1 - On the way to sustainable and hydrogen compatible sealing materials N2 - In this contribution, the sliding performance of newly formulated polymer materials with improved sustainability are investigated and compared with conventional materials. Tribological tests were performed in hydrogen at ambient temperature as well as cryogenic medium. The samples were arranged in a pin-on-disk configuration with a flat pin sliding against a rotating austenitic steel disk. The friction and wear mechanisms are described and discussed by means of surface analyses. T2 - PolyTrib 2024 CY - Portoroz, Slowenia DA - 03.10.2024 KW - High-performance polymers KW - Sliding wear KW - Hydrogen KW - Cryogenic PY - 2024 AN - OPUS4-61419 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine A1 - Cano Murillo, Natalia A1 - Hashimoto, H. A1 - Aoyagi, A. A1 - Dobbelaar, E. T1 - On the way to sustainable and hydrogen compatible sealing materials N2 - In this contribution, the sliding performance of newly formulated polymer materials with improved sustainability are investigated and compared with conventional materials. Tribological tests were performed in hydrogen at ambient temperature as well as cryogenic medium. The samples were arranged in a pin-on-disk configuration with a flat pin sliding against a rotating austenitic steel disk. The friction and wear mechanisms are described and discussed by means of surface analyses. T2 - PolyTrib 2024 CY - Portoroz, Slowenia DA - 03.10.2024 KW - High-performance polymers KW - Sliding wear KW - Hydrogen KW - Cryogenic PY - 2024 SP - 1 EP - 2 AN - OPUS4-61421 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Askar, Enis T1 - Competence centre h2safety@bam N2 - In this presentation the current focus areas of the competence centre H2Safety@BAM are shown. The fields of competence include “Material properties and compatibility”, “Process and plant safety”, “Component testing, component safety and approval” as well as “Sensors, analytics and certified reference Materials. Moreover, the cross-cutting activities regarding “Education and training” and the testing possibilities and planed test facilities at the Test Site for Technical Safety (BAM TTS) are presented. T2 - VDMA P2X4A: P2X Technik-Treffen CY - Online meeting DA - 14.09.2023 KW - Hydrogen KW - Test area hydrogen safety KW - ModuH2Pipe PY - 2023 AN - OPUS4-58333 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - El Harrab, Hayat A1 - Askar, Enis A1 - Franken, T. A1 - Mauss, F. T1 - Experimental and reaction kinetic study of hydrogen ignition behavior at ignition limits N2 - The paper presents the results of an experimental and reaction kinetic investigation of hydrogen ignition at different pressures in a closed vessel, highlighting its non-linear behavior and the effects of radical wall termination. The reaction kinetic simulation predicts the three characteristic ignition limits of hydrogen caused by radical and thermal auto-ignition and is in close agreement with the experimental measurements. The first ignition limit is determined by the chain branching reaction H+O_2→O+ OH. This limit shows strong sensitivity towards the wall termination of O, H and OH radicals. The second ignition limit is influenced by the wall termination of O, H, OH, HO2 and H2O2 radicals. The third ignition limit is dominated by the reaction paths HO_2+HO_2→H_2 O_2+O_2 and H_2 O_2+M→2 OH+M, which is why it shows strong sensitivity towards wall termination of HO₂ and H₂O₂ radicals. Increasing the radical wall termination rate by increasing the sticking coefficient of the radicals at the wall or the surface-to-volume-ratio leads to an increase of the auto-ignition temperature at the same pressure. The introduction of radical wall termination reactions improved the prediction of ignition limits and highlighted the profound effect of the autoclave wall and vessel size on the hydrogen ignition behavior. KW - Radical Wall Termination Reaction KW - Hydrogen KW - Auto-ignition Temperature KW - Ignition Limit PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-647609 DO - https://doi.org/10.1016/j.proci.2025.105980 SN - 1540-7489 VL - 41 SP - 1 EP - 7 PB - Elsevier Inc. AN - OPUS4-64760 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Namwoonde, Andreas Sheuyange T1 - Polymer Composites Under Continuous and Reciprocating Sliding Conditions In Hydrogen N2 - The implementation of hydrogen as an alternative energy source to fossil fuels necessitates the use of compatible materials for safety purposes, and thermoplastics are widely utilized in this context. The application of polymers in gaseous and liquid hydrogen environments requires careful consideration of their tribological performance, as the operating environment is dramatically different from ambient conditions. Friction, wear, and lubrication are crucial factors to consider in this regard. Researchers have investigated various strategies to enhance the tribological performance of polymers in hydrogen environments, including modifying the composition and structure of polymers by incorporating fillers to improve their friction and wear resistance. The tribological properties of polymer composites based on matrices of PEEK, PPS, and PI have been mostly investigated using the continuous sliding test method, and the results indicate that these materials are suitable candidates for tribological applications in both gaseous and liquid hydrogen. This project explores the tribological properties of related polymer composites in hydrogen using continuous and reciprocating motion with a pin-on-disc testing method. T2 - Polytrib2024 CY - Portorož, Slovenia DA - 03.10.2024 KW - Polymers KW - Friction KW - Wear KW - Tribological behaviour KW - Hydrogen PY - 2024 AN - OPUS4-61378 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - From Research to a Standard: The Hollow Specimen Technique for High-Pressure Hydrogen Gas Testing N2 - As the world moves towards a decarbonised economy, the demand for sustainable and low-carbon alternatives is growing rapidly. Hydrogen has an important role to play in this transition, but in order to make the most of hydrogen as an energy carrier, a comprehensive understanding of its impact on the integrity of structural materials is necessary. Metallic materials, mainly steels, are the most commonly used structural materials in various components throughout the hydrogen supply chain. Ensuring their sustainable and safe use in hydrogen technologies is a crucial factor in the development of the hydrogen economy. This is particularly important since hydrogen can promote crack formation and ultimately lead to premature failure in these materials when combined with mechanical load. This process is commonly known as Hydrogen Embrittlement and can occur in almost all the steels used for the hydrogen technologies. Extensive materials qualification is required for the rapid implementation of hydrogen technologies, however, most accepted, and standardised test methods for determining the effect of gaseous hydrogen on metallic materials describe complex and costly procedures that are only available to a very limited extent worldwide. The hollow specimen technique is a simple and economical method that has the potential to overcome the limitations of the current methods and complement them for qualifying metallic materials under high-pressure hydrogen gas. Unlike the conventional autoclave technique, this method requires significantly lower amounts of hydrogen, resulting in fewer safety measures and no need for complex equipment or a specialised laboratory. The technique's low investment and testing costs, simple operation, and shorter testing time make it an optimal for widespread use around the world, thereby increasing the output of results. Initial studies have demonstrated the feasibility of assessing hydrogen effects in metallic materials using the hollow specimen technique. This led to the establishment of an ISO committee to standardise the method. However, there are open questions that currently prevent the technique from being standardised for hydrogen testing. These open questions relate to specimen geometry, inner hole surface and gas quality and are being addressed in the H2HohlZug project, of which the overall aim is to systematically close the gaps towards a standard. This contribution presents the structure and milestones of the project, followed by initial results. T2 - CETIM Workshop Technique H2 CY - Nantes, France DA - 11.12.2025 KW - Hydrogen KW - Hydrogen Embrittlement KW - Hollow Specimen Technique KW - High-Pressure Gaseous Hydrogen KW - TransHyDE KW - H2HohlZug KW - Standardisation PY - 2025 AN - OPUS4-65103 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimault de Freitas, Tomás T1 - Hollow Specimen Method for Tests in High-Pressure Hydrogen Gas: The Role of Geometry, Surface Quality and Gas Purity N2 - The hollow specimen technique is a simple and cost-effective method that has the potential to make materials qualification with pressurised gaseous hydrogen widely accessible to academia and industry. The feasibility of this method for slow strain tensile tests has been demonstrated in several studies, leading to the establishment of the ISO/TC 164/SC 1/WG 9 ISO committee for its standardisation. Questions have emerged during this process, that currently prevent the method from being standardised for hydrogen testing. These questions relate to specimen geometry, specimen manufacturing and gas quality and are being systematically addressed in the TransHyDE-H2HohlZug project. The first results are presented in this poster. T2 - TransHyDE Vollversammlung 2024 CY - Leipzig, Germany DA - 27.11.2024 KW - Hydrogen KW - Hydrogen Embrittlement KW - Hollow Specimen Technique KW - High-Pressure Gaseous Hydrogen KW - Austenitic Stainless Steel KW - TransHyDE KW - H2HohlZug PY - 2024 AN - OPUS4-61847 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Hydrogen - Trust through safety N2 - In den Virtual Talks der DECHEMA wurden allgemeine Aspekte der Sicherheit und Akzeptanz von Wasserstofftechnologien vorgestellt. Wie kann Vertrauen in neue Technologien geschaffen werden, wenn Unfälle aus der Vergangenheit zu Mythen und Märchen führten? Der Vortrag räumt mit allgemeinen Vorurteilen auf und zeigt, dass der Umgang mit Wasserstoff weder unsicherer, noch sicherer ist als der Umgang mit anderen Brenngasen. Basis für den sicheren Umgang mit Wasserstoff ist immer eine Risikoanalyse. N2 - In the DECHEMA Virtual Talks, general aspects of the safety and acceptance of hydrogen technologies were presented. How can trust in new technologies be built when past accidents led to myths and fairy tales? The presentation does away with general prejudices and shows that handling hydrogen is neither more unsafe nor safer than handling other fuel gases. The basis for the safe handling of hydrogen is always a risk analysis. T2 - DECHEMA Virtual Talks CY - Online meeting DA - 23.11.2020 KW - Hydrogen KW - Wasserstoff KW - Safety KW - Sicherer Umgang KW - Sicherheit PY - 2020 AN - OPUS4-52082 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -