TY - JOUR A1 - Bloi, L. M. A1 - Hippauf, F. A1 - Boenke, T. A1 - Rauche, M. A1 - Paasch, S. A1 - Schutjajew, K. A1 - Pampel, Jonas A1 - Schwotzer, F. A1 - Dörfler, S. A1 - Althues, H. A1 - Oschatz, M. A1 - Brunner, E. A1 - Kaskel, S. T1 - Mechanistic insights into the reversible lithium storage in an open porous carbon via metal cluster formation in all solid-state batteries N2 - Porous carbons are promising anode materials for next generation lithium batteries due to their large lithium storage capacities. However, their highsloping capacity during lithiation and delithiation as well as capacity fading due to intense formation of solid electrolyte interphase (SEI) limit their gravimetric and volumetric energy densities. Herein we compare a microporous carbide-derived carbon material (MPC) as promising future anode for all solid-state batteries with a commercial high-performance hard carbon anode. The MPC obtains high and reversible lithiation capacities of 1000 mAh g−1carbon in half-cells exhibiting an extended plateau region near 0 V vs. Li/Li+ preferable for full-cell application. The well-defined microporosity of the MPC with a specific surface area of >1500 m2 g−1 combines well with the argyrodite-type electrolyte (Li6PS5Cl) suppressing extensive SEI formation to deliver high coulombic efficiencies. Preliminary full-cell measurements vs. nickel-rich NMC-cathodes (LiNi0.9Co0.05Mn0.05O2) provide a considerably improved average potential of 3.76 V leading to a projected energy density as high as 449 Wh kg−1 and reversible cycling for more than 60 cycles. 7Li Nuclear Magnetic Resonance spectroscopy was combined with ex-situ Small Angle X-ray Scattering to elucidate the storage mechanism of lithium inside the carbon matrix. The formation of extended quasi-metallic lithium clusters after electrochemical lithiation was revealed. KW - All solid-state battery KW - Microporous carbon KW - Lithium battery KW - Anode PY - 2022 DO - https://doi.org/10.1016/j.carbon.2021.11.061 SN - 0008-6223 VL - 188 SP - 325 EP - 335 PB - Elsevier Ltd. AN - OPUS4-54079 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Perk, M. A1 - Großwig, S. A1 - Pfeiffer, T. A1 - Rembe, M. A1 - den Hartogh, M. A1 - Weege, S. A1 - Krebber, Katerina A1 - Dijk, H. L. T1 - Faseroptische Leckage-Ortung zum Nachweis von Undichtheiten in Bohrlochkomplettierungen N2 - Im Rahmen der Integritätsbewertung einer zementierten 13 3/8" Rohrtour einer Sole-Produktionsbohrung wurden erstmals 2018 zeitgleich faseroptische Temperaturmessungen (DTS, Distributed Temperature Sensing) und faseroptische Akustikmessungen (DAS, Distributed Acoustic Sensing) durchgeführt und ausgewertet. Dazu wurde die Bohrung zeitweise mit Stickstoff bespannt und wieder entlastet. Durch die Bespannung der Bohrung mit Stickstoff in Kombination mit dem Herunterdrücken des Stickstoff-Sole-Spiegels unter den Rohrschuh der 13 3/8" Rohrtour, konnte Stickstoff aus der Kavernenbohrung durch eine Leckagestelle in die Zementation übertreten und dort ein Stickstoff-Reservoir bilden. Bei der anschließenden Stickstoffentlastung erfolgte der Wiederanstieg des Stickstoff-Sole-Spiegels deutlich schneller als die Entleerung des in der Zementation angelegten Stickstoff-Reservoirs. Der dadurch entstandene Druckgradient hatte zur Folge, dass an der Leckagestelle der Stickstoff aus der Zementation in die aufsteigende Sole in Form von Bläschen eingetreten und dort aufgestiegen ist. Dieser Übertritt der Stickstoffbläschen war sowohl mit der Entstehung eines akustischen Geräusches als auch mit einer Temperaturänderung verbunden, welche mit der DAS- und DTS-Technik nachgewiesen werden konnten. Um die Ergebnisse bzgl. ihres physikalischen Hintergrundes zu überprüfen und basierend auf einer mathematisch-physikalischen Grundlage eine nachvollziehbare Interpretation der Messergebnisse zu ermöglichen, wurde ein numerisches Simulationsmodell der gekoppelten Festkörper- und Druckakustik für die Bohrung aufgebaut. Das Modell berücksichtigt die Geologie und die Komplettierung der Kavernenbohrung. Nach Identifikation der Schallquelle konnte mit dem Modell die Ausbreitung des Schalldrucks in der Bohrung erfolgreich nachgestellt werden. Um dieses Verfahren einer simultanen DAS-DTS-Messung in eine feldtaugliche Version zu überführen, läuft seit November 2019 ein breit angelegtes und vom BMWi gefördertes ZIM-Kooperationsprojekt zwischen der Bundesanstalt für Materialforschung und -prüfung (BAM), der IAB Weimar gGmbH, der GESO GmbH & Co. Projekt KG, der DEEP.KBB GmbH sowie der Rembe Consulting PartG mbB. Durch die Messdatenkopplung und den Wegfall der bewegungsbedingten Nachteile einer Messsonde werden präzisere Ergebnisse zur Bewertung der Bohrlochintegrität erwartet. Das Ziel ist, mit Hilfe der noch zu entwickelnden einfachen und robusten Technik, quantitative Aussagen über die Zustände im verrohrten Bohrloch direkt am Messplatz treffen zu können, wobei ein Fokus auf Detektierung und Quantifizierung von Kleinstleckagen liegt. Im Rahmen dieses Forschungsprojektes kommt neben numerischen Berechnungen auch ein geplanter Bohrlochsimulator zum Einsatz, mit dem umfangreiche Untersuchungen zur Ermittlung der Grenzparameter und Detektionsschwellen durchgeführt werden sollen. T2 - DGMK/ÖGEW-Frühjahrstagung 2020 CY - Celle, Germany DA - 15.​04.​2020 KW - Kavernenspeicher KW - Verteilte faseroptische akustische Sensorik KW - Wasserstoffspeicher PY - 2020 UR - https://dgmk.egnyte.com/fl/k3KJMqKMSb#folder-link/ SN - 978-3-947716-04-3 SN - 1433-9013 N1 - Die DGMK/ÖGEW Frühjahrstagung 2020 wurde abgesagt, der Tagungsband aber trotzdem veröffentlicht. - The DGMK/ÖGEW Frühjahrstagung 2020 was cancelled, the proceedings were published nevertheless. VL - DGMK-Tagungsbericht 2020-1 SP - 106 EP - 121 PB - DGMK - Deutsche Wissenschaftliche Gesellschaft für Erdöl, Erdgas und Kohle CY - Hamburg AN - OPUS4-52159 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hicke, Konstantin T1 - Fiber optic distributed acoustic and vibration sensing for condition monitoring of infrastructure and hazard monitoring applications N2 - Fiber optic Distributed Acoustic Sensing (DAS) is an emerging method for many different monitoring purposes, enabling a spatially and temporally resolved collection of acoustic and vibration information over many kilometers. DAS, thus being a "dynamic" sensing technique, allows for online condition monitoring and the detection and localization of threats or hazards in real time via characteristic acoustic/vibration states and their changes or via occurring anomalous signals, respectively. At BAM, we have employed this technology for a number of different applications of monitoring of large infrastructures, e.g., bridges, pipelines, submarine power cables or railway tracks. Currently, we are investigating the use of DAS for further innovative uses, which aim at facilitating the energy transition, enabling "smart" infrastructure and providing the basis for comprehensive hazard monitoring and warning systems, respectively. Our research fields include fiber optic borehole monitoring in the context of hydrogen storage caverns, traffic and road monitoring, using DAS for earthquake monitoring in urban areas for disaster management and long-term monitoring of large-scale subsidence caused by mining activities. Another new topic is structural health monitoring in concrete structures in the framework of the FSP Security. In this talk, we will first briefly present the basics and capabilities of DAS. Then, we will portray our previous and current works related to this technology and show some attractive results. Finally, we will discuss our upcoming projects on exciting new applications of DAS. T2 - Abteilungsseminar 8. CY - Online meeting DA - 24.02.2021 KW - Distributed fiber optic sensing KW - Distributed acoustic sensing KW - DAS KW - Infrastructure monitoring KW - Hazard monitoring PY - 2021 AN - OPUS4-52160 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bischoff, Tristan T1 - Heat storage testing method with realistic operating conditions N2 - Development of a new testing method for comparing efficient stratified heat storages. T2 - World sustainable energy days CY - Online meeting DA - 21.06.2021 KW - Heat storage KW - Stratification KW - Testing Methods KW - Exergy KW - Load profile PY - 2021 AN - OPUS4-52791 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ghafafian, Carineh T1 - The effect of fiber orientation mismatch on scarf joint damage mechanisms under fatigue load N2 - Wind turbine rotor blades commonly fail before their projected 20-year lifespan largely due to defects that originate during manufacturing and are propagated by operational fatigue and environmental conditions. The cost-intensive replacement outcomes lead to a high loss of earnings, and are one of the inhibitors of wind turbine production. A potential repair alternative to restoring the mechanical properties of such lightweight fiber reinforced polymer (FRP) structures is to locally patch these areas with scarf joints. This type of repair allows for a smoother load distribution across the joint, and is favored especially on structures where minor aerodynamic contour changes are key. The effects of such repairs on the structural integrity, however, is still largely unknown. Building upon an understanding of the static load failure mechanism of GFRP scarf joints, presented at the ICCS23 Joint Event in 2020, the influence of the fiber orientation mismatch between parent and repair materials of 1:50 scarf joints on the failure mechanism of monolithic glass FRP specimens under cyclic fatigue load were examined in this study. Specimens with various layups were produced with the vacuum-assisted resin infusion (VARI) process using biaxial E-glass non-crimp fabric (NCF). The patch layers were then joined directly to the parent structure with the VARI using biaxial E-glass NCF with half the areal weight of the parent side to allow for better drapability. This mimics the soft-to-hard patch style utilized in wind turbine blade shell field repairs. The specimens were tested under uniaxial fatigue load, during which they were periodically monitored for damage onset. A comparison of the +45/-45° and 0/90° layups allowed for an understanding of the role of a highly mismatching fiber orientation in the transition zone between parent and patch material on the failure mechanism of the scarf joint. In addition to the tensile strength and stiffness property recovery assessment, a grayscale analysis using in-situ camera images determined the damage state leading to failure in each region across the scarf joint, which varied in the parent material versus scarf joint region, providing insight to the critical regions in this composite structure under cyclic loading. T2 - ICCS24 - 24th International Conference on Composite Structures CY - Online meeting DA - 14.06.2021 KW - Glass fiber reinforced polymers KW - Scarf repairs KW - Damage mechanisms PY - 2021 AN - OPUS4-52817 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Sophie T1 - Entwicklung thermoelektrischer Multilayergeneratoren auf der Basis von Calciumcobaltit N2 - Thermoelectric generators can be used as energy harvesters for sensor applications. Multilayer thermoelectric generators (ML-TEGs) are a promising alternative to conventional π-type generators due to their high filling factor, high capability of automated production and the texturing potential during the production process. Calcium cobaltite is a promising thermoelectric oxide (p-type) with highly anisotropic properties. The following study shows the development of a textured unileg ML-TEG using ceramic multilayer technology. Tape-casting and pressure assisted sintering are applied to fabricate textured calcium cobaltite. Compared to conventional sintering, pressure assisted sintering increases the strength by the factor 10. Thermoelectric properties can be tuned either towards maximum power factor or towards maximum figure of merit depending on the pressure level. As electrical insulation material, a screen-printable glass-ceramic with high resistivity and adapted coefficient of thermal expansion is developed. From various commercial pastes a metallization with low contact resistance is chosen. The unileg ML-TEG is co-fired in one single step. The demonstrators reach 80% of the simulated output power and the power output is highly reproducible between the different demonstrators (99%). These results provide the first proof-of-concept for fabricating co-fired multilayer generators based on textured calcium cobaltite with high power factor, high density, and high strength. N2 - Thermoelektrische Generatoren können zum „Energy harvesting“ für den autarken Betrieb von bspw. Sensoren eingesetzt werden. Eine interessante Alternative zu den herkömmlichen π-Typ Generatoren sind auf Grund der höheren Leistungsdichte und der guten Automatisierbarkeit thermoelektrische Multilayergeneratoren. Calciumcobaltit ist ein vielsprechendes oxidisches Thermoelektrika (p-Typ) mit stark anisotropen Eigenschaften. Die hier vorgestellte Studie zeigt die Entwicklung von texturierten Unileg-Multilayer-Generatoren mittels keramischer Multilayertechnologie. Calciumcobaltit wird durch Foliengießen und druckunterstützte Sinterung texturiert. Im Vergleich zur konventionellen Sinterung verbessert sich die Festigkeit um den Faktor 10. Die thermoelektrischen Eigenschaften können je nach verwendetem Druckniveau hinsichtlich maximalem Power Factor oder hinsichtlich maximalem Gütefaktor optimiert werden. Ein Glaskeramikkomposit wird als Isolationsmaterial mit hohem Volumenwiderstand und angepasstem Wärmeausdehnungskoeffizienten entwickelt. Der Unileg-Multilayer-Generator wird in einem Schritt co-gesintert. Die hergestellten Demonstratoren erreichen 80% der simulierten Output-Leistung. Diese Ergebnisse stellen den ersten Machbarkeitsnachweis für die Herstellung von co-gesinterten Multilayer-Generatoren aus texturiertem Calciumcobaltit mit hohem Power Factor und hoher Festigkeit dar. T2 - Seminar des Lehrstuhls für Funktionsmaterialien, Universität Bayreuth CY - Online meeting DA - 18.06.2021 KW - Thermoelektrischer Generator KW - Multilayertechnik KW - Energy harvesting PY - 2021 AN - OPUS4-52834 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Investigation of the salinization in marine and offshore environment - test methods and challenges N2 - Salinization and contamination of metal surfaces by chloride-containing aerosols is of great importance with regard to corrosion phenomena in the maritime sector and in offshore applications. The evaluation of the scientific literature and regulatory guidelines has shown that there are still many open questions regarding the contamination of metal surfaces by chlorides. This contribution will discuss how salinization of metal surfaces is evaluated and monitored according to current standards and guidelines. T2 - 3rd Task Group Meeting TC124 WG4-TC 250 SC5 Task Group Corrosion CY - Online Meeting DA - 19.05.2021 KW - Maritime atmosphere KW - Salinization KW - Corrosion PY - 2021 AN - OPUS4-52677 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kraus, David A1 - Trappe, Volker T1 - Transverse damage in glass fiber reinforced polymer under thermo-mechanical loading N2 - In this study, the thermomechanical damage behavior of a glass fiber reinforced polymer material is investigated. The coefficients of thermal expansion of the composite as well as the matrix are measured in a wide temperature range. Quasi-static experiments with neat resin, unidirectional and multidirectional laminates are performed as well as fatigue experiments in a temperature range from 213 K to 343 K. This study focusses on the matrix damage due to fiber-parallel loading. A correlation between matrix effort, the dilatational strain energy of the matrix and the damage state of the specimen is demonstrated. It is shown that a fatigue life assessment can be performed with the aid of a temperature-independent master fatigue curve. KW - Composite KW - Glass fiber reinforced polymer KW - Thermo-mechanics KW - Fatigue KW - Damage KW - Temperature PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-527462 DO - https://doi.org/10.1016/j.jcomc.2021.100147 SN - 2666-6820 VL - 5 SP - 100147 PB - Elsevier B.V. AN - OPUS4-52746 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ghafafian, Carineh T1 - Restoring lightweight strength - Effect of localized repairs on the mechanical properties of composites sandwich structures N2 - As a type of high-performance composite material, glass-fiber reinforced plastics (GFRP) are favored for the construction of wind turbine rotor blades due to their high specific strength and stiffness properties (Grasse et al, 2010). During the blade manufacturing process, however, imperfections are often introduced, then further propagated due to harsh environmental conditions and a variety of loads (Caminero et al, 2013; Trappe et al, 2018). This leads to failure significantly before their designed lifespan. Since replacement of entire blades can be a costly potential outcome, localized repairs of the damaged region to restore structural integrity and thus lengthen its lifespan can executed in the field by technicians accessing the blades directly by suspended roping. These methods involve replacing the lost load path with a new material that is joined to the parent structure. In recent years, considerable studies have been conducted to investigate the influence of different repair parameters on the stress distribution, ultimate strength, impact behavior, and residual stresses of bonded repaired structures [Caminero et al, 2013; Trappe et al, 2018; Shufeng et al, 2014; Harman and Rider, 2011; Ahn and Springer, 2000; Lekou and Vionis, 2002). However, there currently do not exist any standardized repair procedures for wind turbine rotor blades. Namely, there is a lack of understanding about the effects of the layup of various repair methods, especially on the damage mechanism and fatigue life of the shells of rotor blades (Caminero et al, 2013; Trappe et al, 2018). This work therefore aims to begin to enrich this knowledge gap by testing the influence of different variables among repair patches on the mechanical properties of sandwich composite structures. Manufactured with the vacuum-assisted resin infusion (VARI) process, the test specimens are produced as a GFRP structure to represent the outer shell portion of a wind turbine blade, then repaired with a scarf joint. Scarf repairs are favored as the most efficient of the common structural joints, as the removal of the damaged area with angled walls leads to a nearly uniform shear stress distribution along the bond surface and no eccentricity in the load distribution (Caminero et al, 2013; Lekou and Vionis, 2002; Siener, 1992). The performance of specific layup methods of repair patches, namely a large-to-small versus small-to-large scheme of repair layers, is studied with static and load-controlled fatigue testing, then compared to pristine test specimens as well as to each other in terms of mechanical property restoration. The transition layer between repair and parent material is especially of interest in the performance of the structure. Damage onset, crack development and eventual failure are monitored in-situ with non-destructive testing methods, including thermography with an infrared camera system and a 3D deformation analysis system, to develop a more robust understanding of the effects of these repair concept variables on wind turbine blade shell structures. T2 - Wind Energy Science Conference CY - Online Meeting DA - 25.05.2021 KW - Glass fiber reinforced polymers KW - Wind turbine blade shell structures KW - Scarf joint repair PY - 2021 AN - OPUS4-52687 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Völzke, Holger A1 - Herold, Christian A1 - Wolff, Dietmar A1 - Orellana Pérez, Teresa A1 - Bollingerfehr, W. A1 - Prignitz, S. A1 - Wunderlich, A. T1 - Abschlussbericht zum FuE-Verbundvorhaben KoBrA: Anforderungen und Konzepte für Behälter zur Endlagerung von Wärme entwickelnden radioaktiven Abfällen und ausgedienten Brennelementen in Steinsalz, Tonstein und Kristallingestein N2 - Im Forschungsvorhaben KoBrA werden Anforderungen an Endlagerbehälter für hochradioaktive Abfälle erstmals systematisch und unter Berücksichtigung des internationalen Standes von Wissenschaft und Technik hergeleitet. Parallel werden die behälterrelevanten Randbedingungen und Beanspruchungsgrößen für Endlagerbehälter in den drei potenziellen Wirtsgesteinen Steinsalz, Tonstein und Kristallingestein ermittelt. Darauf aufbauend werden die zur Erfüllung der Anforderungen unter den gegebenen Einwirkungen und Beanspruchungen notwendigen Behälterfunktionen bestimmt und erste Konzeptideen für zukünftige Endlagerbehälter diskutiert bzw. entwickelt. KW - Endlager KW - Behälter KW - Anforderungen KW - Hochradioaktive Abfälle KW - Wirtsgestein PY - 2020 DO - https://doi.org/10.2314/KXP:1750909669 N1 - Auftraggeber: Bundesministerium für Wirtschaft und Energie (BMWi), Förderkennzeichen: 02E11527 und 02E11537. SP - 1 EP - 110 PB - BGE Technology CY - Peine AN - OPUS4-52289 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Florian, Camilo A1 - Fischer, Daniel A1 - Freiberg, K. A1 - Duwe, M. A1 - Sahre, Mario A1 - Schneider, S. A1 - Hertwig, Andreas A1 - Krüger, Jörg A1 - Rettenmayr, M. A1 - Beck, Uwe A1 - Undisz, A. A1 - Bonse, Jörn T1 - Single Femtosecond Laser-Pulse-Induced Superficial Amorphization and Re-Crystallization of Silicon N2 - Superficial amorphization and re-crystallization of silicon in <111> and <100> orientation after irradiation by femtosecond laser pulses (790 nm, 30 fs) are studied using optical imaging and transmission electron microscopy. Spectroscopic imaging ellipsometry (SIE) allows fast data acquisition at multiple wavelengths and provides experimental data for calculating nanometric amorphous layer thickness profiles with micrometric lateral resolution based on a thin-film layer model. For a radially Gaussian laser beam and at moderate peak fluences above the melting and below the ablation thresholds, laterally parabolic amorphous layer profiles with maximum thicknesses of several tens of nanometers were quantitatively attained. The accuracy of the calculations is verified experimentally by high-resolution transmission electron microscopy (HRTEM) and energy dispersive X-ray spectroscopy (STEM-EDX). Along with topographic information obtained by atomic force microscopy (AFM), a comprehensive picture of the superficial re-solidification of silicon after local melting by femtosecond laser pulses is drawn. KW - Femtosecond laser KW - Silicon KW - Amorphization KW - Crystallization KW - Spectroscopic imaging ellipsometry PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-523687 UR - https://www.mdpi.com/1996-1944/14/7/1651 DO - https://doi.org/10.3390/ma14071651 SN - 1996-1944 VL - 14 IS - 7 SP - 1651-1 EP - 1651-21 PB - MDPI AG CY - Basel, Switzerland AN - OPUS4-52368 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander T1 - Faseroptische Strahlungssensoren für kerntechnische Anwendungen N2 - Faseroptische Strahlungssensoren ermöglichen ein räumlich verteiltes Online-Monitoring entlang der gesamten Sensorfaser. Verschiedene Messverfahren nutzen überwiegend zwei durch die ionisierende Strahlung in optischen Fasern induzierte Effekte, d. h. die Erhöhung der optischen Dämpfung und die damit verbundene Veränderung des Brechungsindex des Fasermaterials. Die Sensitivität der Strahlungssensoren lässt sich je nach Anwendung durch die Wahl der Dotierstoffe im Glasfaserkern sowie der Art des Polymermaterials des POF-Sensors beeinflussen. Ferner ist die Sensitivität auch durch den Betrieb bei geeigneten Wellenlängen einstellbar. Bei dem sensorischen Einsatz von faseroptischen Sensoren muss auch die vorhandene Ausheilung des Sensors sowie die Abhängigkeit der erfassten Messsignale von der Temperatur und der Dosisleistung berücksichtigt werden. T2 - 2. Tage der Standortauswahl CY - Online meeting DA - 11.02.2021 KW - Faseroptischer Strahlungssensor KW - Ortsauflösende Fasersensorik KW - Strahlungsinduzierte optische Dämpfung PY - 2021 AN - OPUS4-52112 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander T1 - Faseroptische Strahlungssensoren für kerntechnische Anwendungen N2 - Faseroptische Strahlungssensoren ermöglichen ein räumlich verteiltes Online-Monitoring entlang der gesamten Sensorfaser. Verschiedene Messverfahren nutzen überwiegend zwei durch die ionisierende Strahlung in optischen Fasern induzierte Effekte, d. h. die Erhöhung der optischen Dämpfung und die damit verbundene Veränderung des Brechungsindex des Fasermaterials. Die Sensitivität der Strahlungssensoren lässt sich je nach Anwendung durch die Wahl der Dotierstoffe im Glasfaserkern sowie der Art des Polymermaterials des POF-Sensors beeinflussen. Ferner ist die Sensitivität auch durch den Betrieb bei geeigneten Wellenlängen einstellbar. Bei dem sensorischen Einsatz von faseroptischen Sensoren muss auch die vorhandene Ausheilung des Sensors sowie die Abhängigkeit der erfassten Messsignale von der Temperatur und der Dosisleistung berücksichtigt werden. T2 - 2. Tage der Standortauswahl CY - Online meeting DA - 11.02.2021 KW - Faseroptischer Strahlungssensor KW - Ortsauflösende Fasersensorik KW - Strahlungsinduzierte optische Dämpfung PY - 2021 AN - OPUS4-52113 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ecke, Alexander T1 - Magnetpartikelbasierte Immunoassays für die Bestimmung von Amoxicillin und Diclofenac im Trinkwasser N2 - Wir berichten hier über die Entwicklung von magnetpartikelbasierten Immunoassays für die Bestimmung zweier relevanter Kontaminanten des Trinkwassers: Diclofenac (DCF) und Amoxicillin (AMX). Für die beiden Analyten wurden die Assays nach unterschiedlichen Prinzipien entwickelt, die sich auch auf weitere Analyten übertragen lassen. Im Vergleich zum herkömmlichen ELISA weisen die hier entwickelten magnetpartikelbasierten Assays einen größeren Messbereich mit niedrigeren Bestimmungsgrenzen bei gleichzeitig deutlich reduzierter Analysendauer auf. Darüber hinaus können die Immunoassays in ein automatisierbares Onlinesystem zur Analyse in der Trinkwasserversorgung implementiert werden. Strategien hierfür werden erläutert. T2 - Spurenstoffe und Krankheitserreger im Wasserkreislauf CY - Online Meeting DA - 19.04.2021 KW - Immunoassay KW - Amoxicillin KW - Diclofenac KW - Immunosensor KW - Magnetpartikel PY - 2021 AN - OPUS4-52466 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tschirschwitz, Rico T1 - Sicherheit elektrochemischer Energiespeicher in Second Life Anwendungen (SEE-2L) – Vorstellung des Verbundprojekts und Ergebnisse aus Vorversuchen N2 - Der Vortrag stellt das BMBF-Verbundprojekt SEE-2L (Sicherheit elektrochemischer Energiespeicher in Second Life Anwendung) vor. Darüber hinaus werden Ergebnisse aus Vorversuchen der Universität Magdeburg vorgestellt, in denen Untersuchungen an Batteriezellen hinsichtlich der Gasfreisetzung beim thermischen Durchgehen durchgeführt wurden. T2 - Projekttreffen BMBF-Vorhaben ALBERO CY - Online meeting DA - 20.04.2021 KW - Stationäre Energiespeicher KW - Elektrische Energiespeicher KW - EES KW - Auswirkungsbetrachtungen PY - 2021 AN - OPUS4-52481 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stargardt, Patrick T1 - Modeling of the cooling behavior of thermoelectric multilayers N2 - Multilayered designs are an attractive approach towards cost-effective manufacturing of thermoelectric generators. Therefore, efforts are being made to co-fire two promising thermoelectric oxides, namely calcium cobaltite and calcium manganate. In this study, ceramic tapes, multilayer technology, and pressure-assisted sintering (PAS) were used. A major challenge for the PAS of low-sintered calcium manganate was cracking during cooling. A relationship between the properties of the release tape used during PAS and the cracking behavior was experimentally observed. To understand the origin of failure, reaction layers in the multilayer were analyzed and thermal stresses during cooling were estimated by finite element (FE) simulations. Thermal expansion, elastic properties, and biaxial strength of the thermoelectric oxides and selected reaction layers were determined on separately prepared bulk samples. The analysis showed that the reaction layers were not the cause for cracking of calcium manganate. Using the FE model, thermal stresses in different manganate multilayer designs with varying properties of the release tape were studied. The FEM study indicated, and a validation experiment proved that the thickness of the release tape has the main effect on thermal stresses during cooling in separately sintered calcium manganate. T2 - Keramik 2021 / Ceramics 2021 CY - Online Meeting DA - 19.04.2021 KW - Fem KW - Thermoelectric KW - Pressure assisted sintering PY - 2021 AN - OPUS4-52489 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank A1 - Komann, Steffen T1 - Aktuelle Entwicklungen und Prüfungen der BAM N2 - Es werden im Rahmen des Vortrages die aktuellen Prüftätigkeiten und Arbeitsschwerpunkte der BAM vorgestellt. Des Weiteren wird darüber berichtet was es Neues in der aktuellen Normen- und Richtlinienentwicklung gibt. T2 - Informationsveranstaltung zum Transport radioaktiver Stoffe CY - Online meeting DA - 14.04.2021 KW - Gefahrgutregeln der BAM KW - Fallprüfungen KW - Radioaktive Materialien KW - Zulassung PY - 2021 AN - OPUS4-52493 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander A1 - Krebber, Katerina T1 - Faseroptische Strahlungssensoren für kerntechnische Anwendungen N2 - Der Anstieg der Vielfalt nuklearer Anwendungen weit über die Bereiche der kerntechnischen Stromerzeugung erhöht die Relevanz der Entwicklung und Anwendung neuer Technologien zur Strahlungsüberwachung. Auch die offenen Sicherheitsfragen bei der Entsorgung radioaktiver Abfälle einschließlich Zwischen- und Endlagerungsproblematik verstärkt die Nachfrage nach effizienten Monitoringsystemen zum Schutz von Mensch und Umwelt vor ionisierender Strahlung. Aufgrund ihrer messtechnisch vorteilhaften Materialeigenschaften stellen die faseroptischen Strahlungssensoren eine vielversprechende Alternative zu traditionellen Dosimetern dar. Bedingt durch ihre kleinen Abmessungen, elektromagnetische Unempfindlichkeit und ihr geringes Gewicht können faseroptische Sensoren in einer harschen Umgebung an schwer zugänglichen Stellen eingesetzt werden. Darüber hinaus bietet diese Art der Sensoren die Möglichkeit der ortsverteilten Messung entlang der gesamten Sensorfaser. Somit kann durch eine einzelne optische Faser eine Vielzahl an punktuell messenden Sensoren ersetzt werden. Dieser Beitrag beschreibt die in der BAM vorangetriebenen Entwicklungen unterschiedlicher Sensorprinzipien, -lösungen und -verfahren zur Detektion ionisierender Strahlung. T2 - 2. Tage der Standortauswahl CY - Online meeting DA - 11.02.2021 KW - Faseroptischer Strahlungssensor KW - Ortsauflösende Fasersensorik KW - Strahlungsinduzierte optische Dämpfung KW - Gammastrahlung KW - Rayleigh-Streuung KW - Brillouin-Streuung PY - 2021 SP - 43 AN - OPUS4-52211 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander T1 - Optical fibers for sensing applications: Towards ionizing radiation monitoring N2 - Overview about existing fiber optic sensing techniques including ionizing radiation monitoring. T2 - WP7 Meeting EU project PREDIS CY - Online meeting DA - 05.02.2021 KW - Fiber optic sensor KW - Radiation-induced attenuation KW - Radiation sensing fibers KW - Distributed sensing PY - 2021 AN - OPUS4-52090 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sandoval Saldias, Janina T1 - Chloridische Salzschmelzen als latente Wärmespeicher N2 - Latente Wärmspeicher auf der Basis von NaCl-KCl-MgCl2 Mischungen stellen eine kostengünstige Option für die Energiespeicherung von Prozesswärme dar. Der Beitrag gibt einen Überblick über die materialwissenschaftlichen Herausforderungen im System Salz-Legierung, welche gelöst werden müssen, um diese Speichertechnologie industriell zu etablieren. T2 - DMG Sektionstreffen Angewandte Mineralogie und Kristallographie CY - Online Meeting DA - 25.02.2021 KW - Wärmespeicher KW - Korrosion KW - Salzschmelzen PY - 2021 AN - OPUS4-52234 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -