TY - CONF A1 - Ghafafian, Carineh A1 - Popiela, Bartosz A1 - Trappe, Volker T1 - Damage Mechanisms of Scarf Joint Repairs for Wind Turbine Rotor Blade Shell Applications N2 - Wind turbine rotor blades, made of fiber reinforced polymers (FRP), often fail before their projected 20-year lifespan, largely due to defects that originate during manufacturing and are propagated by operational fatigue and environmental conditions. The cost-intensive replacement outcomes lead to a high loss of earnings, and are one of the inhibitors of wind turbine production [1]. A potential repair alternative is to locally patch these areas of the blades with adhesively bonded structural repairs. However, the effects of such repair methods of the outer shell region on the structural integrity of the rotor blades are still largely unknown, and are thus investigated in this project. The shell components of rotor blades are made of FRP composite material sandwiching a lightweight core, often a rigid foam or Balsa wood. The repair methods involve replacing the lost load path with a new material that is joined to the parent structure [2]. Repairs in this project focus on the scarf method, which allow for a smoother load distribution across the joint, aiming to study the damage mechanism of glass FRP scarf repairs for wind turbine blade shell applications. Namely, the source and path of the damage initiation and propagation, role of the interface between parent and patch material, and the role of the fiber orientation mismatch at this interface are examined. Biaxial ±45° and 0/90° FRP specimens are produced with the vacuum-assisted resin infusion (VARI) process using E-glass non-crimp fabric. The patch layers are then joined using VARI with a scarf ratio of 1:50, using glass FRP fabric with half the areal weight of the parent side to allow for better drapability. The methods and practices in specimen production are based on common industry practice in rotor blade shell manufacturing and repairs. The specimens are tested under uniaxial tensile load, during which they are periodically monitored for damage onset. A comparison of the ±45° and 0/90° specimens allows for an understanding of the role of a highly mismatching fiber orientation in the transition zone between parent and patch material on the failure mechanism of the scarf joint. Although failure in both orientations begins as delamination at the joint edge, the difference in the mechanisms at play in the two different specimen types leads ultimately to different fracture paths. Namely, in the inter fiber failure mechanism of the ±45° specimens, the higher interlaminar strength compared to the intralaminar strength of the laminate leads to intralaminar failure of the ±45° scarf joint specimens. Alternatively, the competition in the 0/90° specimens lies between the interlaminar strength and fiber failure strength, and here we experience failure primarily across the scarf joint length. The scarf joint in the 0/90° specimens disrupts the continuity of the load-carrying 0° layers, directing the failure path to remain primarily along the scarf joint. Experimental results are compared to finite element analyses of scarf patch repairs on glass FRP sandwich specimens with the same respective layup orientations, where the damage initiation regions are identified and correlated to fiber orientation, serving as a bridge to future work which will experimentally examine the scarf repair patches on sandwich shell specimens. T2 - Joint Event: ICCS23 - 23rd International Conference on Composite Structures & MECHCOMP6 - 6th International Conference on Mechanics of Composites CY - Online meeting DA - 01.09.2020 KW - Wind turbine blade shells KW - Glass fiber reinforced polymers KW - Scarf repairs PY - 2020 AN - OPUS4-51175 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heuser, Lina A1 - Sobek, P. A1 - Körner, S. A1 - Müller, Ralf T1 - Sintering of silver-alkali zinc borate glass composites N2 - High conductive silver-glass-metallization-pastes are key components in photovoltaics and advanced microelectronics. However, the underlying mechanisms of liquid phase sintering as silver dissolution, diffusion and reprecipitation are poorly understood so far. In the current work, the influence of different network modifier in alkali-zinc-borate paste-glasses on liquid phase sintering of silver-glass-composites was studied. Therefore, silver-glass-composites containing 30 vol% glass were prepared, using low melting X2O-ZnO-B2O3 glasses with X = Na, Li, and Rb (NZB, LZB, and RZB). Glass transition temperature, viscosity, glass-silver wetting, crystallization and sintering behavior was studied by means of thermal analysis, dilatometry, heating microscopy and microscopy. Similar glass transition temperatures of 450 °C (RZB), 460 °C (LZB) and 465 °C (NZB) were found by means of thermal analysis for glasses under study. Also, all glasses have a similar crystallization onset at about 550 °C, even though exhibiting with a different degree of crystallization. Despite these similarities, however, the sintering behavior, measured in terms of area shrinkage, significantly differs for the composites. This finding indicates a different degree of silver dissolution. Assuming that dissolved silver reduces the viscosity, this effect could explain why glass crystallization starts at lower temperature in the composites. For example, the crystallization peak of LZB at 629 °C measured for pure glass powder compacts was decreased to 586 °C for the composite. Confirmatively, microstructure analyses indicate different degrees of silver dissolution, as e.g. revealed by different amount of silver precipitates within the residual glass phase, and reprecipitation. Best silver dissolution appeared for the RZB glass. Nevertheless, the final densification of RZB was retarded probably due to swelling and crystallization. T2 - XRM Workshop CY - Halle, Germany DA - 03.03.2020 KW - Silver-glass-metallization-paste KW - Sintering KW - Alkali ions PY - 2020 AN - OPUS4-51243 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias T1 - Overview of metal seal tests performed at BAM and implications for extended interim storage N2 - The investigation of the long-term performance of sealing systems employed in containers for radioactive waste and spent nuclear fuel is one research focus area for division 3.4 “Safety of Storage Containers” at the Bundesanstalt für Materialforschung und -prüfung. The behaviour of metallic seals, which are employed in interim storage casks for used fuel and high active waste, over time is of high importance for ensuring safe enclosure. Therefore, investigations on these systems were started at BAM to get a general understanding of the relevant processes. Our investigations comprise investigations on different parameters which influence the seal performance and the main part is focussed on the time and temperature dependent behaviour. In this contribution an overview of the performed tests and their respective results will be given. A focus will lie on a comparison between seals with large torus diameter in comparison to small diameters. Our aim is to understand the long-term behaviour of the sealing systems for evaluation of their performance during possible extended interim storage and subsequent transportation. T2 - 4th Workshop on Safety of Extended Dry Storage of Spent Nuclear Fuel CY - Online meeting DA - 03.06.2020 KW - Seal performance KW - Metal seal KW - Leakage rate PY - 2020 AN - OPUS4-50843 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank T1 - Retaining Competence for Safe Transports of Radioactive Material N2 - The nuclear phase out in Germany will lead to a challenge finding skilled staff for all areas in nuclear business. Transport of spent fuel and high-level nuclear waste is an ongoing task over the next decades during the decommissioning of nuclear power plants and after the interim storage. The international regulations were adapted and address the issue of transports after storage now. The topic of aging and assessment of the development of the state-of-art technology are in focus. German research funds are supporting the investigations of future challenges of transport and storage of the nuclear heritage. BAM is involved and works on several topics related to the aging issue of packages. The behaviour of spent fuel claddings, long-term behaviour of metal and elastomeric gaskets and sensor/monitoring techniques of waste disposal are examples of research fields. T2 - 7th Nuclear Decommissioning & Waste Management Summit 2020 CY - London, UK DA - 12.02.2020 KW - Aging management KW - Transport KW - Spent fuel behaviour KW - Disposal PY - 2020 AN - OPUS4-50987 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Palkowski, Carsten T1 - Test methods for air conditioners N2 - Comparison of test methods for air conditioners that are currently discussed in standardization. The limitations of the current standard are shown and different options for the further development of the standard are presented T2 - Arbeitsgruppensitzung des Fachverbands Gebäude-Klima CY - Online meeting DA - 28.05.2020 KW - air conditioner KW - test method KW - Load-based testing KW - energy label PY - 2020 AN - OPUS4-50829 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Palkowski, Carsten A1 - Wachau, André A1 - Simo, Anne T1 - Test methods for heat pumps N2 - Comparison of different test methods for the determination of the seasonal performance of heat pumps: 1) The current test standard EN14825, 2) the compensation test method and 3) the dynamic test method. T2 - Impact Assessment / Consultation Space and Water Heaters WG2 Testing CY - Online meeting DA - 02.04.2020 KW - Heat pump KW - Energy label KW - Seasonal performance KW - Compensation method KW - Dynamic method PY - 2020 AN - OPUS4-50713 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Palkowski, Carsten T1 - Technical Meeting BAM RRT for Heat Pumps N2 - Kickoff meeting for the BAM round robin test for load-based heat pump testing T2 - Kickoff meeting BAM RRT for heat pumps CY - Online meeting DA - 26.03.2020 KW - Heat pump KW - Round robin test KW - Load-based testing KW - Compensation method KW - Energy efficiency PY - 2020 AN - OPUS4-50715 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Palkowski, Carsten T1 - Technical Meeting BAM RRT for Air Conditioner N2 - Kickoff meeting for the BAM round robin test for load-based air conditioner testing. T2 - Kickoff meeting BAM RRT for air conditioner CY - Online meeting DA - 26.03.2020 KW - Air conditioner KW - Round robin test KW - Load-based testing KW - Compensation method KW - Energy efficiency PY - 2020 AN - OPUS4-50716 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Palkowski, Carsten T1 - Dynamic Test Method - an Update N2 - An update about the dynamic test method for the determination of the seasonal performance of heat pumps given at the CEN/TC 113/WG 7 meeting. T2 - Meeting of CEN/TC 113/WG 7 CY - Courbevoie, France DA - 14.01.2020 KW - Heat pump KW - Dynamic test method KW - Seasonal performance KW - Coefficient of performance PY - 2020 AN - OPUS4-50579 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Widjaja, Martinus Putra T1 - Sample Performance Chart (SPC) for displaying the results from a multiscale model N2 - The stacking sequence of a real scale type IV pressure vessels has been found. Feasibility study of a multiscale model has been carried out by modifying the original stacking sequence. All of the results were displayed in a Sample Performance Chart (SPC), where different burst pressure in terms of mean and scatter had been found. T2 - Consortium Meeting FiBreMoD CY - Valence, France DA - 17.02.2020 KW - Fibre break KW - Multiscale model KW - Reduced volume method KW - Sample performance chart KW - Type IV pressure vessels PY - 2020 AN - OPUS4-50563 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schönhals, Andreas A1 - Zorn, R. A1 - Böhning, Martin T1 - Inelastic neutron scattering as a tool to investigate  polymers of intrinsic microporosity for green membrane processes and electronic applications N2 - Polymers with intrinsic microporosity are promising candidates for the active separation layer in green gas separation membranes and as active materials for electronic applicatons. Here, by means of inelastic neutron scattering, the vibrational density of states (VDOS) and the molecular mobility were investigated for PIM-1, the prototypical polymer with intrinsic microporosity. The results are compared to data measured for a more conventional high-performance polyimide used in gas separation membranes (Matrimid). The measured data show the characteristic low frequency excess contribution to the VDOS above the Debye sound wave level, generally known as the Boson peak in glass-forming materials. In comparison to the Boson peak of Matrimid, that of PIM-1 is shifted to lower frequencies. This shift is discussed considering the microporous, sponge-like structure of PIM-1 as providing a higher compressibility at the molecular scale than for conventional polymers. Elastic fixed window scans were measured on a neutron backscattering spectrometer to have an overview about the molecular dynamics at a time scale of ca. 1 ns. The temperature dependence of the estimated mean squared displacement shows a step-like increase in the temperature range from 100 K to 250 K indicating the onset of some molecular mobility. The nature of this motional process was analysed in detail by quasielastic neutron scattering combining Time-of-Flight and backscattering where the data are discussed with regard to both the q- and the temperature dependence. T2 - Symposium on Large Scale Facilities CY - Berlin, Germany DA - 09.03.2020 KW - Polymer membranen PY - 2020 AN - OPUS4-50546 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Ökodesign und Energielabel: Entwicklung, geltendes Recht und Ausblick N2 - Der Vortrag gibt einen Überblick über die Entwicklung der Anforderungen, die geltenden und kommenden Regeln für Produkte unter den beiden Rechtsinstrumenten und berührt die Frage, was in Zukunft den Schwerpunkt der Rechtssetzung darstellen wird T2 - Jahrestagung 2020 FA Haushaltstechnik der dgh CY - Nuremberg, Germany DA - 06.02.2020 KW - Ökodesign KW - Energieverbrauchskennzeichnung KW - Energieeffizienz KW - Ressourceneffizienz KW - EU-Recht PY - 2020 AN - OPUS4-50355 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schönfelder, Thorsten T1 - Kerntechnische Entsorgung Herausforderungen im Transport und bei der Lagerung N2 - Nach der Reaktorkatastrophe in Fukushima 2011 hat die Bundesregierung beschlossen die Nutzung der Kernenergie bis zum Jahr 2022 zu beenden. Seitdem erfolgt der Rückbau und die Stilllegung der kerntechnischen Anlagen in Deutschland. Dieser Vortrag erörtert die Herausforderungen, die sich mit dem Transport und der Lagerung von Kernbrennstoffen ergeben und leitet daraus Anforderungen ab, die an Transportbehälter gestellt werden. T2 - Ausgewählte Kapitel der Werkstofftechnik - Brand- und Explosionsverhalten von Werkstoffen CY - Wuppertal, Germany DA - 24.01.2020 KW - Kerntechnische Entsorgung KW - Rückbau KW - Transport- und Lagerbehälter PY - 2020 AN - OPUS4-50428 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schürmann, K. A1 - Pittner, Andreas A1 - Schaumann, P. A1 - Rethmeier, Michael T1 - Experimental investigations on the fatigue resistance of automatically welded tubular X-joints for jacket support structures N2 - The development within the offshore wind sector towards more powerful turbines combined with increasing water depth for new wind parks is challenging both the designer as well as the manufacturer of bottom fixed support structures. Besides XL-monopiles, the market developed an innovative and economic jacket support structure which is based on automatically manufactured tubular joints combined with standardized pipes. Besides the improvements for a serial manufacturing process the automatically welded tubular joints show a great potential in terms of fatigue resistance e.g. due to a smooth weld geometry without sharp notches. However, these benefits are not considered yet within the fatigue design process of automatically manufactured jacket substructures according to current standards due to the lack of suitable S-N curves. Therefore, 32 axial fatigue tests on single and double-sided automatically welded tubular X-joints have been performed to determine a new hot spot stress related S-N curve. Based on these constant amplitude fatigue tests a new S-N curve equal to a FAT 126 curve was computed which implicitly includes the benefits of the automatically welding procedure. T2 - EERA DeepWind 2020 CY - Trondheim, Norway DA - 15.01.2020 KW - Notch stress approach KW - Tubular X-joints KW - Automated manufacturing KW - Fatigue tests KW - Structural stress approach PY - 2020 AN - OPUS4-51873 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, David T1 - From W. C. Röntgen to modern Tomography N2 - A not complete review of X-Ray related milestones from 1895 to the 21st century. T2 - ITN GW4SHM, First Training Event CY - Online Meeting DA - 23.11.2020 KW - X-Ray KW - Computed Tomography KW - Laminography KW - Digital Detector Arrays KW - Wilhelm Conrad Röntgen PY - 2020 AN - OPUS4-51881 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Überarbeitung des GfKORR-Leitfadens „Korrosionsschutz von Offshore-Windenergieanlagen" N2 - Der Vortrag stellt den aktuellen Stand und die Diskussionsthemen für die Überarbeitung des GfKORR-Leitfadens "Korrosionsschutz von Offshore-Windenergieanlagen" vor. T2 - Gemeinsame Sitzung des GfKORR Arbeitskreises „Korrosionsschutz von Windenergieanlagen“ mit der Fachgruppe „Korrosionsschutz“ der WAB e.V. CY - Online meeting DA - 07.12.2020 KW - Leitfaden KW - Korrosionsschutz KW - Offshore-Windenergieanlagen PY - 2020 AN - OPUS4-51784 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akkerman, Floris T1 - Aktuelles zur Ökodesign-Verordnung - Entwicklung und Einschätzung zum Inverkehrbringen N2 - Vorstellung der Rechtsinstrumente Ökodesign, Darstellung der Entwicklung und Einschätzung zu Szenarien zum Inverkehrbringen am Beispiel Kühlmöbel T2 - Handel-Hersteller-Dialog der FG Kühlmöbel des VDMA CY - Online meeting DA - 07.12.2020 KW - Ökodesign KW - Energieverbrauchskennzeichnung KW - Energieeffizienz KW - Kühlmöbel KW - Supermarktkälte PY - 2020 AN - OPUS4-51817 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reichardt, Adrian A1 - Schubert, Sven T1 - Assessment of ageing effects at BAM N2 - In Germany, spent nuclear fuel and vitrified high active waste is stored in dual purpose casks (DPC) at interim storage facilities. In order to ensure the transportability of the DPC to a final repository in future, the maintenance of the package design approval is realized. Therefore, the assessment of possible ageing effects during interim storage is necessary to ensure an evaluation of the transportability. The lecture presents BAM's current ageing evaluation concept in the field of trasnport law. T2 - IRSN-BAM Symposium - Safety of Transport and Storage Packages CY - Online meeting DA - 19.11.2020 KW - Ageing KW - DPC KW - Interim storage KW - Ageing management PY - 2020 AN - OPUS4-51718 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin A1 - Quercetti, Thomas A1 - Wille, Frank T1 - Outcomes of Three Large-Scale Fire Reference Tests Conducted in Propane Gas Fire Test Facility N2 - Packages for the transport of high-level radioactive material are designed to withstand severe accidents. Hypothetical severe accident conditions are defined in the IAEA Regulations for the Safe Transport of Radioactive Materials. One of these accident conditions is the thermal test, mainly consisting of a 30 minute fully engulfing 800°C pool fire or an equally severe fire test. The heat fluxes into the package depend substantially on the fire characteristics and the surface temperature of the package. Fire tests can be performed at BAM on a propane gas fire test facility. In order to investigate the heat fluxes over a wide range of surface temperatures in this test facility a fire reference package was designed for multiple use. The package represented the outer geometry of a specific transport cask for radioactive waste. The fire reference package is a closed steel sheet cylinder with a wall thickness of 10 mm, a length of 1500 mm and a diameter of 1050 mm. The package was instrumented with thermocouples and filled with heat resistant insulation material. Three open-air fire tests were performed in the BAM propane gas fire test facility. The flames exposure time period varied slightly for the fire tests. The wind direction as well as the wind speed were measured and changed between and during the tests. Test stand parameters such as wind shield location and propane gas volume flow were chosen constant for the three tests. The locally measured fire reference package steel sheet temperatures were used for the calculation of heat fluxes as function of time and surface temperature. The measured temperatures allowed further calculations. In a first approach effective fire characteristics of the propane gas fire, including the flame temperature, the fire convection coefficient and a radiation exchange coefficient mathematically describing the determined average heat flux over the surface temperature were calculated. T2 - Abteilungskolloquium 3.3 CY - Online meeting DA - 03.12.2020 KW - Fire KW - Heat flux KW - Convection coefficient KW - Adiabatic surface temperature KW - IAEA PY - 2020 AN - OPUS4-51778 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Askar, Enis T1 - Explosion Protection for Hydrogen Applications N2 - In the this lecture the safety related properties of hydrogen compared to other fuel gases and the explosion protection measures of avoiding flammable mixtures, avoiding ignition sources and mitigating the consequences of explosions are presented. T2 - Guest Lecture at the University of Birmingham CY - Online meeting DA - 19.10.2020 KW - New energy carriers KW - Explosion limits KW - Ignition energy KW - Ignition source KW - Renewable energy PY - 2020 AN - OPUS4-51531 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hicke, Konstantin A1 - Karapanagiotis, Christos T1 - KI, Machine Learning und faseroptische Sensorik N2 - Die Verwendung von Methoden des Maschinellen Lernens (ML) und der Künstlichen Intelligenz (KI) im Fachbereich 8.6 Faseroptische Sensorik wird dargestellt. Die vielfältigen Möglichkeiten, Machine Learning auf Basis Künstlicher Neuronaler Netze (ANN) für eine schnelle und effiziente Datenverarbeitung eizusetzen werden demonstriert. Hierfür werden Beispiele für die Anwendungszwecke Messgrößenberechnung, Entrauschen, Interpolation, Bildverarbeitung und Messdatenauswertung aufgezeigt. T2 - Foresight Prozess AM, AP 4, Workshop „In Situ Sensorik“ CY - Online-Meeting DA - 09.11.2020 KW - Verteilte faseroptische Sensorik KW - KI KW - Künstliche Intelligenz KW - Machine Learning KW - Künstliche Neuronale Netze PY - 2020 AN - OPUS4-51545 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Lars A1 - Scheidemann, Robert A1 - Schönfelder, Thorsten A1 - Komann, Steffen A1 - Wille, Frank T1 - Drop tests assessment of internal shock absorbers for packages loaded with encapsulations for damaged spent nuclear fuel N2 - Damaged spent nuclear fuel (DSNF) can be loaded in German dual-purpose casks (DPC) for transport and interim storage. Encapsulations are needed to guarantee a safe handling and a tight closure, separated from the package enclosure. These encapsulations shall be durable and leak-tight for a long storage period, because they are usually not accessible within periodical inspections of the DPC. Due to the general design of DPCs for standard fuel assemblies, specific requirements have to be considered for the design of encapsulations for DSNF to ensure the loading in existing package designs. Especially the primary lid system of a DPC is designed for maximum loads due to the internal impact of the content during drop test conditions. The main difference of encapsulations for damaged spent nuclear fuel is that they have usually a much higher stiffness than standard fuel assemblies. Therefore the design of an internal shock absorber, e.g. at the head of an encapsulation is required to reduce mechanical loads to the primary lid system during impacts. BAM as part of the German competent authority system is responsible for the safety assessment of the mechanical and thermal package design, the release of radioactive material and the quality assurance of package manufacturing and operation. Concerning the mechanical design of the encapsulation BAM was involved in the comprehensive assessment procedure during the package design approval process. An internal shock absorber was developed by the package designer with numerical analyses and experimental drop tests. Experimental drop tests are needed to cover limiting parameters regarding, e.g. temperature and wall thickness of the shock absorbing element to enable a detailed specification of the whole load-deformation behavior of the encapsulation shock absorber. The paper gives an overview of the assessment work by BAM and points out the main findings which are relevant for an acceptable design of internal shock absorbers. The physical drop tests were planned on the basis of pre-investigations of the applicant concerning shape, dimension and material properties. In advance of the final drop tests the possible internal impact behavior had to be analyzed and the setup of the test facility had to be validated. The planning, performance and evaluation of the final drop tests were witnessed and assessed by BAM. In conclusion it could be approved that the German encapsulation system for damaged spent nuclear fuel with shock absorbing components can be handled similar to standard fuel assemblies in existing package designs. T2 - Pressure Vessels & Piping Conference 2020 CY - Online meeting DA - 03.08.2020 KW - Drop tests KW - Internal shock absorber KW - Design assessment of RAM packages KW - Encapsulations for damaged spent nuclear fuel PY - 2020 AN - OPUS4-51550 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Askar, Enis T1 - Safety Related Properties of Hydrogen Mixtures - Laboratory Tests N2 - Wasserstoff unterscheidet sich hinsichtlich der sicherheitstechnischen Eigenschaften von anderen brennbaren Gassen, v.a. durch die sehr niedrige Mindestzündenergie und die sehr hohe Flammengeschwindigkeit. In der Praxis treten Wasserstoffgemische z.B. durch Einspeisung von Wasserstoff in das Erdgasnetz, bei der Herstellung von Synthesegas (CO, H2) und in Biogasanlagen auf. Die sicherheitstechnischen Eigenschaften von Wasserstoffgemischen wurden experimentell untersucht und werden vorgestellt. Darüber hinaus wurde die Genauigkeit von Berechnungsmethoden für sicherheitstechnische Eigenschaften von Wasserstoffgemischen untersucht. N2 - Hydrogen differs from most other flammable gases regarding the safety related properties. Mainly the minimum ignition energy (MIE) is particularly low and the burning velocity is particularly high. Hydrogen mixtures are formed in different hydrogen applications, for example if hydrogen is added to the existing natural gas grid, if synthetic gas (mixture of CO and H2) is produced or in biogas plants. Safety related properties of hydrogen mixtures were determined experimentally and are presented in this presentation. Moreover the accuracy of estimation methods for safety related properties of hydrogen mixtures is evaluated.” T2 - Center for Hydrogen Safety 2020 European Conference CY - Online meeting DA - 20.10.2020 KW - Explosion Protection KW - Explosion Limits KW - Minimum Ignition Energy KW - Ignition Source KW - Synthetic Gas PY - 2020 AN - OPUS4-51530 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin A1 - Quercetti, Thomas A1 - Wille, Frank T1 - Fire reference package - Results of large-scale fire tests N2 - Packages for the transport of high-level radioactive material are designed to withstand severe accidents. Hypothetical severe accident conditions are defined in the IAEA Regulations for the Safe Transport of Radioactive Materials. One of these accident conditions is the thermal test, mainly consisting of a 30 minute fully engulfing 800°C pool fire or an equally severe fire test. The heat fluxes into the package depend substantially on the fire characteristics and the surface temperature of the package. Fire tests can be performed at BAM on a propane gas fire test facility. In order to investigate the heat fluxes over a wide range of surface temperatures in this test facility a fire reference package was designed for multiple use. The package represented the outer geometry of a specific transport cask for radioactive waste. The fire reference package is a closed steel sheet cylinder with a wall thickness of 10 mm, a length of 1500 mm and a diameter of 1050 mm. The package was instrumented with thermocouples and filled with heat resistant insulation material. Three open-air fire tests were performed in the BAM propane gas fire test facility. The flames exposure time period varied slightly for the fire tests. The wind direction as well as the wind speed were measured and changed between and during the tests. Test stand parameters such as wind shield location and propane gas volume flow were chosen constant for the three tests. The locally measured fire reference package steel sheet temperatures were used for the calculation of heat fluxes as function of time and surface temperature. The measured temperatures allowed further calculations. In a first approach effective fire characteristics of the propane gas fire, including the flame temperature, the fire convection coefficient and a radiation exchange coefficient mathematically describing the determined average heat flux over the surface temperature were calculated. T2 - IRSN-BAM Symposium - Safety of Transport and Storage Packages CY - Online meeting DA - 19.11.2020 KW - Fire reference KW - Calorimetric test KW - Propane KW - Heat flux KW - Propane gas fire test facility PY - 2020 AN - OPUS4-51686 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thomas, Sebastian T1 - Improvement of Type Approval Regulations of Pressure Vessels for Hydrogen Fueled Vehicles using Probabilistic Methods N2 - Composite pressure vessels (CPVs) are becoming the state of the art for storage for compressed hydrogen (CH2) in automotive applications. There is a strong interest of car manufacturers to use lightweight and less-costly gas storage units. In order to reduce the necessary amount of expensive carbon fibre, the nominal safety margins are becoming gradually smaller, pushing the limits of the regulations for type approval. At the same time, the total volume of these vessels increases to extend the range of the vehicles, increasing the consequences for worst-case scenarios like the rupture of the CPVs in service. This presentation presents insights gained in the project “TAnk HYdrogen Automotive” (TAHYA). Its aim is to improve the safety of current regulations for type approval of pressure vessels for the use in hydrogen fueled vehicles, namely GTR No. 13 and ECE R 134. For the assessment of safety, the probabilistic approach developed by division 3.5 of BAM is used. Monte-Carlo-Simulations were conducted leading to the identification of several weak spots, mainly found in the burst test and the batch test. By changing the requirements for burst tests and the approach for batch tests, the identified weak spots can be strongly reduced. T2 - Colloquium of Department 3 CY - Online meeting DA - 19.11.2020 KW - Monte-Carlo Simulation KW - Safety Assessment KW - Pressure Vessel PY - 2020 AN - OPUS4-51696 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zaghdoudi, Maha A1 - Weber, Mike A1 - Kömmling, Anja A1 - Jaunich, Matthias A1 - Wolff, Dietmar T1 - Numerical modelling of compression stress relaxation and compression set of elastomer O-rings during aging N2 - Elastomer seals are used in many industrial applications due to their excellent mechanical properties at a wide range of temperatures. Their high versatility and recovery potential under several load conditions make them well suitable for the application in containers designed for transport, storage and/or disposal of radioactive materials. In containers for low and intermediate level radioactive waste, elastomer seals are used as barrier seals, and as auxiliary seals in storage and transportation casks (dual purpose casks) for heat generating radioactive waste, such as spent fuel and high-level waste. While a seal exchange at defined intervals is typical in many conventional applications, it is impossible or at least hard to perform when principles of minimization of radiation exposure have to be considered and prohibit an unnecessary cask handling. An extensive knowledge of the change of the elastomer’s properties during aging and the availability of reliable end-of-lifetime criteria to guarantee the permanent safe enclosure of the radioactive material is mandatory. As BAM is involved in most of the national cask licensing procedures and in the evaluation of cask-related long-term safety issues, great efforts have been already made and are still planned to scientifically support this task. Compression stress relaxation and compression set were identified as key indicators of elastomer long-term performance and quantitatively investigated in comprehensive test programs. Among other representative types of elastomers, specimens made from ethylene propylene diene rubber (EPDM) were tested before, during and after aging to capture the most important of their complex mechanical properties. In the presented study, exemplary results were used to simulate the compression stress relaxation and the compression set of elastomer O-rings during aging. Regarding the influence of temperature, the time temperature superposition principle is applied in the relaxation analysis of elastomer O-rings. The proposed model is implemented in the commercial finite element software ABAQUS/Standard® [1] with a sequential temperature displacement coupling. Numerical results match the experimental compression stress relaxation measurements well. The prediction of compression set values after long-term aging shows a relatively good agreement with the experimental results. Nevertheless, all input parameters derived from the specimen tests, additional assumptions concerning boundary conditions and modeling strategy are discussed with regard to the identified slight discrepancies. The possibility to extend the finite element model to represent the O-ring seal’s ability to recover after a (fast) partial release is taken into account T2 - ASME 2020 Pressure Vessels & Piping Conference (PVP2020) CY - Online meeting DA - 03.08.2020 KW - Stress relaxation KW - Ageing KW - Compression Set KW - O-ring KW - Sequential analysis KW - Simulation PY - 2020 AN - OPUS4-52135 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - State of the art and development perspectives of deep foundations for offshore wind converters T1 - Estado del arte y perspectivas de desarrollo de las cimentaciones profundas para aerogeneradores offshore N2 - This presentation provides an overview of the main geotechnical aspects associated with deep foundations in the context of offshore wind generation. The most common deep foundation typologies (large diameter monopiles and multipile typologies) as well as new trends under development (e.g. suction buckets) and their current limits will be briefly described. The talk concludes with a brief review of advanced topics not covered in classical pile design, such as hydromechanical coupling effects (pore pressure generation), cyclic accumulation of deformations, cyclic degradation of axial capacity or pile-setup gains. T2 - Ciclo de Conferencias: Aplicaciones de la Geotecnia en la generación de Energía. Sociedad Argentina de Ingeniería Geotécnica SAIG CY - Online meeting DA - 02.12.2020 KW - Offshore wind energy KW - Deep foundations KW - Offshore geomechanics PY - 2020 AN - OPUS4-51729 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Untersuchung der Gefährdung von Personen und Bauwerken in Folge des Versagens von LNG-Kraftstoffspeichern für Fahrzeuge in Tunneln N2 - Der Markt von LNG als Transportgut und als Kraftstoff ist seit Jahrzehnten kontinuierlich am Wachsen, wobei das Hauptanwendungsgebiet im Schiffsverkehr lag. LNG ist verflüssigtes Erdgas mit Hauptbestandteil Methan, das neben fossilen, aus erneuerbaren Quellen, wie synthetischen Methan oder Biogas, gewonnen werden kann. LNG hat als Kraftstoff sehr gute Eigenschaften dessen Potenzial als alternativer Kraftstoff zu Diesel im Schwerlast- und Fernverkehr gesehen wird. Dabei weist LNG gegenüber Diesel geringere Emissionen von CO2, Feinstaub, Stickoxiden und Lärm auf und hat gegenüber anderen erneuerbaren Energiespeichern wie CNG, Elektrobatterien oder Wasserstoff die höchste volumetrische und zweitgrößte gravimetrische Energiedichte. Neben seinen Vorteilen zu anderen erneuerbaren Energieträgern birgt LNG durch seine sehr niedrige Temperatur von bis zu 160°C und seiner Brennbarkeit aber auch neue Gefahren für Personen und Infrastrukturen. Zur Bewertung von Gefahren und zur späteren Durchführung von Risikobewertungen bedarf es Methoden und Modellen deren Untersuchung Ziel des Forschungsprojekts war. Schwerpunkt der Untersuchung stellt die Freisetzung von LNG in Tunnel, mit sich anschließender Stoffausbreitung und verzögerter Zündung des Kraftstoff-Luftgemisches dar. Unfallszenarien mit Brandereignissen in Tunnel haben gezeigt, dass diese meist mit hohen Personen, Bauwerks und volkswirtschaftlichen Schäden verbunden sind. Des Weiteren zeigten Untersuchungen das von Gasexplosionen in Umschließungen wie sie ein Tunnel darstellt, mehr Gefahren ausgehen als von Gasexplosionen im Freifeld. Im Vortrag werden die untersuchten Modelle und die aus dem Projekt gewonnenen Erkenntnisse für die Stoffausbreitung und Verbrennung der Gasphase von LNG in Umschließungen vorgestellt. T2 - Abteilungs-Vortragsseminar-Doktoranden CY - BAM Berlin, Germany DA - 08.12.2020 KW - LNG KW - Erdgas KW - Störfall KW - CFD KW - Schwergas PY - 2020 AN - OPUS4-51959 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Palkowski, Carsten T1 - BAM Round Robin Test for Heat Pumps and Air Conditioners N2 - Preliminary results of the BAM RRTs are given in this presentation. T2 - VHK Meeting CY - Online meeting DA - 11.11.2020 KW - Heat Pumps KW - Air Conditioners KW - Round Robin Test KW - Load-Based Test Method KW - Energy Label PY - 2020 AN - OPUS4-51969 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Winckelmann, Alexander A1 - Abad Andrade, Carlos Enrique T1 - High-resolution optical spectrometry for lithium isotope ratio analysis N2 - An alternative method for lithium isotope amount ratio analysis is proposed by combining atomic absorption spectrometry with spectra data analysis by machine leaning. It is based on the well-known isotope shift of around 15 pm for the electronic transition at wavelength 670.7845 nm which can be measured by a high-resolution continuum source atomic absorption spectrometer (HR-CS-AAS). For isotope amount ratio analysis, a scalable three boosting machine learning algorithm (XGBoost) was employed and calibrated with a set of samples with a 6Li isotope amount fraction ranging from 99% to 6%. The absolute Li isotope amount fractions of these calibration samples were previously measured by multi-collector inductively coupled plasma mass spectrometry (MC-ICP-MS) and used as ab-initio data for the machine learning algorithm. Validation of the machine leaning model was performed with two standard reference materials (LSVEC and IRMM-016). The procedure was employed for the isotope amount ratio determination of a set of stock chemicals (Li2CO3, LiNO3, LiCl, LiOH, and LiF) as well as a BAM candidate LiMNC cathode reference material. Achieved uncertainties are one order of magnitude higher than those obtained by MC-ICP-MS. This precision and accuracy is nonetheless sufficient to resolve natural occurring variations in Lithium isotope ratios. Also, the LiMNC material was analyzed by HR-CS-AAS with and without matrix purification. The results are comparable within statistical error. T2 - Groupseminar - GFZ Potsdam CY - Online Meeting DA - 27.10.2020 KW - Lithium batteries KW - HR-CS-AAS KW - Machine learning KW - Isotope analysis PY - 2020 AN - OPUS4-51572 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - John, Sebastian A1 - Duffner, Eric A1 - Mair, Georg A1 - Moosavi, Robabeh A1 - Auster, Jürgen T1 - Delfin - Statusbericht zum 4.HJM N2 - Präsentation über den Fortschritt der BAM zum Vorhaben Delfin, welches sich mit der Entwicklung und Schädigungsneigung von Composite-Wasserstoffbehältern für den Anwendungsfall KFZ beschäftigt T2 - 4. Halbjahresmeeting zum Vorhaben Delfin CY - Online meeting DA - 21.10.2020 KW - Wasserstoff KW - Impact KW - Druckbehälter PY - 2020 AN - OPUS4-51495 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai A1 - Orellana Pérez, Teresa A1 - Mair, Georg A1 - Maiwald, Michael A1 - Sobol, Oded T1 - Hydrogen - Trust through safety N2 - In den Virtual Talks der DECHEMA wurden allgemeine Aspekte der Sicherheit und Akzeptanz von Wasserstofftechnologien vorgestellt. Wie kann Vertrauen in neue Technologien geschaffen werden, wenn Unfälle aus der Vergangenheit zu Mythen und Märchen führten? Der Vortrag räumt mit allgemeinen Vorurteilen auf und zeigt, dass der Umgang mit Wasserstoff weder unsicherer, noch sicherer ist als der Umgang mit anderen Brenngasen. Basis für den sicheren Umgang mit Wasserstoff ist immer eine Risikoanalyse. N2 - In the DECHEMA Virtual Talks, general aspects of the safety and acceptance of hydrogen technologies were presented. How can trust in new technologies be built when past accidents led to myths and fairy tales? The presentation does away with general prejudices and shows that handling hydrogen is neither more unsafe nor safer than handling other fuel gases. The basis for the safe handling of hydrogen is always a risk analysis. T2 - DECHEMA Virtual Talks CY - Online meeting DA - 23.11.2020 KW - Hydrogen KW - Wasserstoff KW - Safety KW - Sicherer Umgang KW - Sicherheit PY - 2020 AN - OPUS4-52082 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Transport von defekten Lithiumbatterien: Umsetzungspraxis der neuen Rechtsvorschriften, Wo besteht Forschungsbedarf? N2 - Transport von defekten Lithiumbatterien - die BAM setzt die Vorschriften des internationalen Gefahrguttransportrechts für defekte Lithiumbatterien um. Um die Kompetenz hierfür sicherzustellen, bedarf es eigener Forschungstätigkeit. Auch im zuständigen UN Gremium werden Untersuchungen durchgeführt, an denen die BAM beteiligt ist. T2 - Fachkonferenz Lithiumbatterien CY - Göttingen, Germany DA - 22.01.2020 KW - Lithiumbatterien KW - Gefahrguttransport KW - ADR PY - 2020 AN - OPUS4-50806 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg A1 - Duffner, Eric A1 - Thomas, Sebastian T1 - Bergungsdruckgefäße - Vorschlag zur Definition von Druckgefäßen N2 - Es wird plastisch dargestellt, mit welcher Intention und welchem Ziel Deutschland in die Juni Sitzung des UN ECOSOC SubCom TDG gehen wird, um ein Druckvolumenbegrenzung für Druckgefäße zu erreichen. T2 - BAM-DIN-IGV-DVFG-Jahresgespräch 2020 CY - Berlin, Germany DA - 27.02.2020 KW - Bergungsdruckgefäß KW - Konsequenzbegrenzung KW - Volumenbegrenzung KW - Druck-Volumen-Produkt KW - UN-Modellvorschriften KW - Akzeptanz PY - 2020 AN - OPUS4-53146 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg T1 - Markthochlauf von Wasserstoff - Vertrauen durch probabilistische Sicherheitsbewertung der H2-Speicher N2 - Der Vortrag beginnt mit dem erwarteten Bedarf an Wasserstoff und der Frage der Risikosteuerung bei stattfindender Marktdurchsetzung. Dem gegenüber ist an einem Beispiel der Prozess der Regelsetzung gestellt, was die Notwendigkeit pro-aktiven Handelns zeigt. Es wird über die risikobasierte Definition von Sicherheit gezeigt, welche Bedeutung die Erfassung der Fertigungsstreuung hat und wie die quantitative Erfassung und Bewertung aussehen könnte. Zuletzt wird über den Aspekt der Alterung auf das Potential probabilistischer Zulassungsansätze verwiesen und aufgezeigt, wie die Wirkung von Vorschriften nach dem probabilistischen Sicherheitskriterium bewertet und optimiert werden kann. T2 - 9. HYPOS-Dialog: Grüner Wasserstoff, aber sicher! (Uni Magdeburg) CY - Magdeburg, Germany DA - 11.09.2020 KW - Wasserstoffspeicher KW - Monte-Carlo-Experiment KW - Lebensdauervorhersage KW - Statistische Bewertung KW - Sicherheit KW - Population PY - 2020 AN - OPUS4-53154 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Jaunich, Matthias A1 - Zencker, Uwe A1 - Simbruner, Kai A1 - Nagelschmidt, Sven A1 - Herbrich, Uwe A1 - Keller, Christian A1 - Qiao, Linan T1 - Research at BAM on Metal Seal Performance and Fuel Rod Integrity N2 - The presentation provides an update on preliminary results from research projects in the area of long term performance of metal seals and fuel rod integrity as safety relevant components of spent fuel transport and storage casks for spent nuclear fuel. T2 - Extended Storage Collaboration Program (ESCP) Winter Meeting 2020 CY - Online meeting DA - 09.11.2020 KW - Metal seal KW - Safety KW - Interim storage KW - Spent nuclear fuel KW - Fuel rod PY - 2020 AN - OPUS4-51615 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simbruner, Kai A1 - Zencker, Uwe A1 - Völzke, Holger T1 - Embrittlement of Spent Fuel Claddings ‒ Results of Ring Compression Tests N2 - An established method for characterizing cladding material is the Ring Compression Test (RCT), where a small, cylindrical sample of the cladding tube is subjected to a compressive load. This test is a laboratory representation of a fuel rod load case and has shown a high susceptibility to failure under the occurrence of radial hydrides. Certain hydride morphologies and low temperature might even lead to brittle fracture at very small loads. The BAM research project BRUZL (Fracture mechanical analysis of spent fuel claddings during long-term dry interim storage) aims to study the results of quasi-static RCTs and to establish numerical models to gain an in-depth understanding of the stress state during such experiments. Using a fracture mechanical approach, cases of sudden failure during the RCT procedure are used to characterize the material behaviour and establish a failure criterion. As an integral part of the project BRUZL, quasi-static Ring Compression Tests have been performed to identify all experimental details, which might be helpful for numerical modelling. Unirradiated samples of the cladding material ZIRLO® have been subjected to hydrogen charging and a thermo-mechanical treatment for radial hydride reorientation. Sample preparation, testing procedures, and analysis results are presented. A numerical model has been established and an elastic-plastic material model was derived from as-received RCT samples by inverse finite element analyses. Cohesive zone modelling has been implemented to reproduce sudden load drops during RCT. The project is funded by the Federal Ministry for Economic Affairs and Energy (BMWi) under contract no. 1501561. T2 - 4th GRS Workshop on Safety of Extended Dry Storage of Spent Nuclear Fuel CY - Online meeting DA - 03.06.2020 KW - Ageing Management KW - Cladding Embrittlement KW - Extended Storage KW - Ring Compression Test KW - Spent Nuclear Fuel PY - 2020 AN - OPUS4-51988 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Wille, Frank A1 - Wolff, Dietmar T1 - Update on the German Spent Fuel Management Strategy N2 - The presentation provides an update on the German spent fuel Management strategy in the areas of transportation, dry interim storage and deep geological disposal. T2 - IAEA 18th TWG-NFCO CY - Online meeting DA - 07.09.2020 KW - Spent nuclear fuel KW - Final disposal KW - Safety KW - Transport and storage cask PY - 2020 AN - OPUS4-51616 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simbruner, Kai A1 - Zencker, Uwe A1 - Völzke, Holger T1 - Brittle failure analysis of spent fuel zirconium alloy claddings during long-term dry interim storage - Current approach at BAM N2 - Understanding the mechanical behaviour of fuel cladding is decisive for an extended dry interim storage period beyond the currently licensed period of 40 years in Germany and subsequent handling, transport, and disposal considering normal and accidental conditions. Since fuel cladding acts as the first barrier for spent fuel, its integrity should be demonstrated to enable safe and secure discharge and handling options after interim storage and subsequent transportation in preparation of final disposal. An established method for characterizing cladding material is the Ring Compression Test (RCT), where a small, cylindrical sample of the cladding tube is subjected to a compressive load. This test is a laboratory representation of a fuel rod load case and has shown a high susceptibility to failure under the occurrence of radial hydrides. Certain hydride morphologies and low temperature might even lead to brittle fracture at very small loads. The BAM research project BRUZL (Fracture mechanical analysis of spent fuel claddings during long-term dry interim storage) aims to study the results of quasi-static RCTs and to establish numerical models to gain an in-depth understanding of the stress state during the experiments. Using a fracture mechanical approach, cases of sudden failure during the RCT procedure are used to characterize the material behaviour and establish a failure criterion. As an integral part of the project BRUZL, quasi-static Ring Compression Tests have been performed to identify all experimental details, which might be helpful for numerical modelling. Unirradiated samples of the cladding material ZIRLO® have been subjected to hydrogen charging and a thermo-mechanical treatment for radial hydride reorientation. Sample preparation, testing procedures, and analysis results are presented. A numerical model has been established and an elastic-plastic material model was derived from as-received RCT samples by inverse finite element analyses. Cohesive zone modelling has been implemented to reproduce sudden load drops during RCT. The project is funded by the Federal Ministry for Economic Affairs and Energy (BMWi) under contract no. 1501561. T2 - Kolloquium der Abteilung 3 CY - Online meeting DA - 05.11.2020 KW - Ageing Management KW - Cladding Embrittlement KW - Extended Storage KW - Ring Compression Test KW - Spent Nuclear Fuel PY - 2020 AN - OPUS4-51987 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias A1 - Zaghdoudi, Maha A1 - Kömmling, Anja A1 - Wolff, Dietmar A1 - Völzke, Holger T1 - Elastomer seals - overview and development N2 - The talk summarizes the current and future investigations of elastomer seal materials in division 3.4. T2 - IRSN-BAM Symposium Safety of Transport and Storage Packages CY - Online meeting DA - 19.11.2020 KW - Seal KW - Degradation KW - Ageing PY - 2020 AN - OPUS4-51751 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Butz, Adam A1 - Fedelich, Bernard A1 - Rehmer, Birgit A1 - Mäde, L. T1 - Detection and prediction of high temperature fatigue crack growth around notches in polycrystalline nickel base alloy N2 - Im Rahmen eines Vorhabens wurden Methoden zur Reduktion des Versuchsaufwandes bei der Modellerstellung für LCF-Lebensdauervorhersage untersucht. Einige dieser Methoden sind hier kurz vorgestellt. N2 - Methods for reducing the experimental effort necessary for the development of LCF life time prediction models were investigated. Some of these methods are briefly presented here. T2 - 4th International Symposium for Fatigue Design and Material Defects CY - Online meeting DA - 26.05.2020 KW - LCF KW - Mechanistic Modelling KW - Fatigue KW - Data Fusion PY - 2020 AN - OPUS4-50904 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tschirschwitz, Rico T1 - BAM-Aktivitäten im Bereich Elektrische Energiespeicher N2 - Der Beitrag stellt die aktuellen, relevanten BAM-Projekte im Bereich der Sicherheit elektrischer Energiespeicher vor. Weiterhin werden derzeitige Kooperationen mit der vfdb präsentiert. T2 - 82. Sitzung Referat 10, Umweltschutz der vfdb (Vereinigung zur Förderung des deutschen Brandschutzes e.V.) CY - Online meeting DA - 04.11.2020 KW - Behälterversagen KW - Fahrzeugbrand KW - Auswirkungsbetrachtung KW - Alternative Antriebe KW - Fragment PY - 2020 AN - OPUS4-51522 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Orellana Pérez, Teresa A1 - Mair, Georg A1 - Holtappels, Kai A1 - Maiwald, Michael A1 - Sobol, Oded T1 - Die Wasserstoffstrategie der BAM; Kompetenzzentrum H 2 safety@bam N2 - Das Thema Wasserstoff ist an der BAM seit mehr als hundert Jahren aktuell und steht auch gegenwärtig im Zentrum zahlreicher Forschungs- und Kooperationsaktivitäten. Mit der aktuellen Wasserstoff-Strategie der BAM werden wichtige Voraussetzungen dafür geschaffen, dass der Markthochlauf gelingt und die technische Sicherheit und Überwachung der Infrastrukturen und Anlagen gewährleistet ist – von der Erzeugung, über den Transport bis zur Speicherung und Bereitstellung von Wasserstoff als Energieträger der Zukunft. T2 - 1st Digital AK PostDocs Meeting CY - Online meeting DA - 01.10.2020 KW - Kompetenzzentrum H2Safety@BAM KW - Wasserstoff KW - Wasserstoffstrategie PY - 2020 AN - OPUS4-51371 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg A1 - Maiwald, Michael A1 - Orellana Pérez, Teresa A1 - Sobol, Oded A1 - Holtappels, Kai T1 - BAM - Bundesanstalt für Materialforschung und -prüfung: Hydrogen - Safety in Technology and Chemistry N2 - The presentation starts with some key figures about BAM. Then it introduces BAM's competence centre H2Safety@BAM and shows aspects of special competence of the centre. It closes with information about the engagement of BAM in European research projects on hydrogen and a reference to our bilingual paper about our hydrogen strategy. T2 - 27th Hydrogen Europe Research General Assembly CY - Online meeting DA - 02.07.2020 KW - Material properties and compatibility KW - Component testing KW - Safety assessment KW - Approval KW - Sensors KW - Inspection KW - Gas behaviour KW - Safe handling PY - 2020 AN - OPUS4-53155 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiele, Marc A1 - Baeßler, Matthias T1 - Fatigue crack detection methods for high-cyclic loaded steel structures and challenges in mechanical testing N2 - For the generation of renewable energy offshore wind farms play an important role. The majority of these wind generators are connected to steel foundation structures. Steady increasing power output of these wind turbines leads to new challenges as well for engineers of the related support structures. Caused by the high-cyclic loading of these structures by wind and waves fatigue plays a very important role. Besides the consideration of fatigue within the design process it is additionally an important topic and challenge to monitor the existing steel structures relating to potential fatigue cracks occurring during their lifetime. This plays a role for a fundamental understanding of mechanisms as investigated in testing but also for inspection in real structures. Since the structures of the offshore wind generators are very large and in addition partially under water effective and reliable methods for fatigue crack detection are required. This contribution will present results of recent investigations on different crack detection methods applied on high-cycle fatigue tests on small welded steel samples as well as on welded steel components. The comparison of these measurements will show what are the advantages and disadvantages of the different methods and which method is potentially more suitable for the application on real offshore wind structures. It is outlined where challenges for detection methods exist. Furthermore, in this context the resulting challenges for the execution of material testing especially caused by the increasing dimensions of wind energy converters will by exemplarily presented. T2 - EERA JP Wind & SETWind Online Annual Event 2020 CY - Online meeting DA - 14.09.2020 KW - Fatigue KW - Crack detection KW - Steel structures PY - 2020 AN - OPUS4-51356 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Yevtushenko, O. A1 - Le, Quynh Hoa A1 - Bettge, Dirk T1 - Corrosive CO2-stream components, challenging for materials to be used in CC(U)S applications N2 - This contribution provides current findings regarding materials susceptibility for CCUS applications. Basing on results gathered in 2 German long-term projects (COORAL and CLUSTER) suitable materials are introduced as well as dominating impurities of the CO2 stream and corrosion mechanisms. Investigations cover the whole CCUS process chain and provide the following recommendations for certain parts. Commercially available carbon steels are suitable for compression and pipelines as long as moisture content and impurities are limited (water 50 to 100 ppmv, SO2 and NO2 ca. 100 ppmv). Corrosion rates increase with increasing water content (0.2 – 20 mm/a). Condensation of acids and therefore droplet formation is always possible, even at low water contents. A low SO2 content within the CO2-stream might be more important than a low water content. Cr13-steels showed a general susceptibility to shallow pitting and pitting. So, they seem to be not suitable for CCUS applications. Low alloyed steels showed better corrosion behavior (predictable uniform corrosion). For direct contact with saline aquifer fluids only high alloyed steels shall be used. T2 - WCO Webinar on the occasion of Corrosion Awareness Day - Corrosion and Low-Carbon Energies CY - Frankfurt, Germany DA - 24.04.2020 KW - CO2-corrosion KW - CCUS KW - Pipeline KW - Carbon Capture PY - 2020 AN - OPUS4-50699 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias A1 - Rackwitz, F. A1 - Lüddecke, F. T1 - Recap: Main Results of the BUMP Study and Relevance for VERBATIM N2 - Zusammenfassung des Forschungsprojekts BUMP hinsichtlich der Relevanz für das Projekt VERBATIM N2 - BUMP had been a theoretical prestudy on open issues for the pile tip buckling of large monopiles. The presentation summarizes the main results and considers the impact for the ongoing VERBATIM project. VERBATIM is set up as a mainly experimental verification project for pile buckling. T2 - Kick-Off Projekt VERBATIM CY - BAM, Berlin, Germany DA - 23.01.2020 KW - Buckling piles circular shells PY - 2020 AN - OPUS4-50515 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Keserović, Amela A1 - Beck, Joana A1 - Sarmiento Klapper, Helmut A1 - Boduch, A. A1 - Dimper, Matthias A1 - Stoljarova, A. A1 - Faes, W. A1 - Zimmer, S. T1 - Metallic Materials for Geothermal Applications N2 - The aim of the work presented was the evaluation of corrosion resistance of various materials in geothermal Waters as a base to create a catalogue of suitable materials for applications in (not only) German geothermal power plants. Users shall be enabled to have a basis for designing such facilities. High alloyed corrosion resistant alloys are suitable and do not cause copper or lead deposition. They shall be chosen for future design of the piping system, either in massive or in cladded form, if crevices formation with non-metallic materials can be prevented! T2 - IFPEN-Workshop: Corrosion in Low-Carbon Energies CY - Online meeting DA - 03.11.2020 KW - Geothermal KW - Corrosion KW - Saline brine PY - 2020 AN - OPUS4-51511 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nerger, Deborah A1 - Moosavi, Robabeh A1 - Bracklow, F. A1 - Hering, M. A1 - Kühn, T. A1 - Curbach, M. A1 - Hille, Falk A1 - Rogge, Andreas T1 - Impact damage characterization at RC plates with planar tomography and FEM N2 - Prediction of dynamic effects of reinforced concrete structures under impact loading is a technical challenge. This is a consequence of the great variability of the physical properties resulting from the wide adaptability of reinforced concrete and a consequence of the wide range of impact loading. Experiments and numerical investigations are normally used on a small scale to address the problem. In this paper, impact tests on reinforced conrete plates with the lateral dimensions of 1.5 m x 1.5 m and a thickness of 30 cm are presented. In bending reinforcement, besides the velocity two properties are varied, the diameter and the spatial distribution of the rebars. Experiments are performed at the Otto-Mohr-Laboratory of the Institute of Concrete Structures of the Technische Universit¨at Dresden. Due to the accelerated fall of the impactor the velocity ranges between 20 and 70 m/s. In addition to the measured quantities such as bearing forces, accelerations are also measured at 4 different positions on and under the plate, as well as the deflection at several positions. The measured data are used for the analysis of the damage form and the numerical examinations with the program Ansys Autodyn and the material model after Drucker-Prager. Numerical investigations support the tests, with detailed analysis of individual effects. These numerical computations and the planar tomographic investigations were carried out at BAM in Berlin. With the help of planar tomographic evaluation, the damaged structure is made visible and compared with the numerical results. Influences of the bending reinforcement are explained on the basis of damage evaluation in the local area and on selected measured values. In addition to the test evaluation, the tomographic and numerical methods are presented. T2 - XI International Conference on Structural Dynamics (EURODYN 2020) CY - Online meeting DA - 23.11.2020 KW - Post-impact evaluation KW - Damage characterization KW - Planar tomography KW - Drucker-Prager KW - Ansys Autodyn PY - 2020 AN - OPUS4-51768 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Stoljarova, A. A1 - Regenspurg, S. T1 - Deposition of Brine Components on Materials in Geothermal Conditions T1 - ОСАЖДЕНИЕ КОМПОНЕНТОВ ГЕОТЕРМИЧЕСКИХ ВОД НА МАТЕРИАЛЫ В ГЕОТЕРМАЛЬНЫХ УСЛОВИЯХ N2 - Since geothermal wells are a feasible energy source to replace fossil fuel supply, many technologies have been developed to take advantage of geothermal energy. Nevertheless, service conditions in geothermal facilities are in many cases extreme in terms of corrosion due to the chemical composition of hydrothermal fluids and temperatures. Therefore, materials selection based on preliminary material qualification is essential to guarantee a secure and reliable operation of the facilities. During operation of a geothermal research facility in Groß Schönebeck copper and lead effects have been found downhole. Occurring mechanisms and measures to prevent precipitation or scaling needed to be investigated as well as potential influences of such precipitates on corrosion resistance of metallic materials used for equipment. This contribution deals with the evaluation of the corrosion behavior of carbon steel and corrosion resistant alloys in copper and/or lead containing artificial geothermal water, simulating the conditions in the Northern German Basin. The behavior of these materials in an artificial geothermal water obtained by electrochemical measurements and exposure tests are presented. While carbon steel exhibits precipitation and deposition, higher alloyed material shows different response to such species and a higher resistance in saline geothermal water. Basing on these results the suitability of the investigated corrosion resistant alloy is given for use in such conditions, whereas carbon steel creates difficulties due to its susceptibility to Cu- and Pb-precipitation. N2 - Поскольку геотермальные скважины являются реальным источником энергии для замены поставок ископаемого топлива, было разработано множество технологий для использования преимуществ геотермальной энергии. Тем не менее, условия эксплуатации на геотермальных установках во многих случаях являются экстремальными с точки зрения коррозии из-за химического состава гидротермальных жидкостей и температур. Таким образом, выбор материалов на основе предварительной квалификации имеет важное значение для обеспечения безопасной и надежной работы геотермальных объектов. Во время работы исследовательской установки в Грос Шёнебек (Groß Schönebeck) в скважине было обнаружено воздействие меди и свинца. Необходимо изучить возникшие механизмы и меры для предотвращения депозиции или образования коррозии, а также потенциальное влияние таких осаждений на коррозионную стойкость металлов, используемых для оборудования. Этот доклад посвящен оценке коррозионного поведения углеродистой стали и коррозионно-стойких сплавов в геотермальной воде, содержащей медь и / или свинец, моделирующей условия в Северогерманском бассейне (North German basin). Представлено поведение этих металлических материалов в геотермальной воде, полученной путем электрохимических измерений и испытаний на воздействие. В то время как углеродистая сталь демонстрирует коррозию и отложения, высоколегированный материал демонстрирует более высокую стойкость в соленой геотермальной воде. На основании этих результатов пригодность исследуемого коррозионно-стойкого сплава дана для использования в данных условиях, тогда как углеродистая сталь создает трудности из-за ее восприимчивости к депозиции солей меди и свинца. T2 - ХV International Conference Problems of Corrosion and Corrosion Protection of Materials “CORROSION-2020” CY - Online meeting DA - 15.10.2020 KW - Copper KW - Lead KW - Corrosion KW - Steel KW - Geothermal PY - 2020 UR - http://www.ipm.lviv.ua/corrosion2020/ AN - OPUS4-51438 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -