TY - CONF A1 - Mair, Georg A1 - Thomas, Sebastian T1 - Consequences of the reduced minimum burst pressure on the production surveillance N2 - First the acceptance rates resulting from the analysis of different minimum burst ratios and standards are displayed and explained. Especially the problems resulting from a further reduction if the minimum burst ratio are shown. For a better understanding of these results the process of analysing the acceptance rate is explained in detail. This contains the alleged contradiction between safety of samples due to its scatter while the rejected sample provides a higher mean strength. Then the importance of batch testing is explained and leads to the recommendation to have a strong interaction between provided mean strength and requested maximum of production scatter. T2 - 8 th WG on rev GTR 13 CY - Online meeting DA - 02.03.2020 KW - Minimum burst ratio KW - Production scatter KW - Mean burst pressure KW - Batch testing KW - Acceptance rate PY - 2020 AN - OPUS4-53147 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Widjaja, Martinus Putra T1 - Sample Performance Chart (SPC) for displaying the results from a multiscale model N2 - The stacking sequence of a real scale type IV pressure vessels has been found. Feasibility study of a multiscale model has been carried out by modifying the original stacking sequence. All of the results were displayed in a Sample Performance Chart (SPC), where different burst pressure in terms of mean and scatter had been found. T2 - Consortium Meeting FiBreMoD CY - Valence, France DA - 17.02.2020 KW - Fibre break KW - Multiscale model KW - Reduced volume method KW - Sample performance chart KW - Type IV pressure vessels PY - 2020 AN - OPUS4-50563 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thomas, Sebastian T1 - Improvement of Type Approval Regulations of Pressure Vessels for Hydrogen Fueled Vehicles using Probabilistic Methods N2 - Composite pressure vessels (CPVs) are becoming the state of the art for storage for compressed hydrogen (CH2) in automotive applications. There is a strong interest of car manufacturers to use lightweight and less-costly gas storage units. In order to reduce the necessary amount of expensive carbon fibre, the nominal safety margins are becoming gradually smaller, pushing the limits of the regulations for type approval. At the same time, the total volume of these vessels increases to extend the range of the vehicles, increasing the consequences for worst-case scenarios like the rupture of the CPVs in service. This presentation presents insights gained in the project “TAnk HYdrogen Automotive” (TAHYA). Its aim is to improve the safety of current regulations for type approval of pressure vessels for the use in hydrogen fueled vehicles, namely GTR No. 13 and ECE R 134. For the assessment of safety, the probabilistic approach developed by division 3.5 of BAM is used. Monte-Carlo-Simulations were conducted leading to the identification of several weak spots, mainly found in the burst test and the batch test. By changing the requirements for burst tests and the approach for batch tests, the identified weak spots can be strongly reduced. T2 - Colloquium of Department 3 CY - Online meeting DA - 19.11.2020 KW - Monte-Carlo Simulation KW - Safety Assessment KW - Pressure Vessel PY - 2020 AN - OPUS4-51696 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - John, Sebastian A1 - Duffner, Eric A1 - Mair, Georg A1 - Moosavi, Robabeh A1 - Auster, Jürgen T1 - Delfin - Statusbericht zum 4.HJM N2 - Präsentation über den Fortschritt der BAM zum Vorhaben Delfin, welches sich mit der Entwicklung und Schädigungsneigung von Composite-Wasserstoffbehältern für den Anwendungsfall KFZ beschäftigt T2 - 4. Halbjahresmeeting zum Vorhaben Delfin CY - Online meeting DA - 21.10.2020 KW - Wasserstoff KW - Impact KW - Druckbehälter PY - 2020 AN - OPUS4-51495 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai A1 - Orellana Pérez, Teresa A1 - Mair, Georg A1 - Maiwald, Michael A1 - Sobol, Oded T1 - Hydrogen - Trust through safety N2 - In den Virtual Talks der DECHEMA wurden allgemeine Aspekte der Sicherheit und Akzeptanz von Wasserstofftechnologien vorgestellt. Wie kann Vertrauen in neue Technologien geschaffen werden, wenn Unfälle aus der Vergangenheit zu Mythen und Märchen führten? Der Vortrag räumt mit allgemeinen Vorurteilen auf und zeigt, dass der Umgang mit Wasserstoff weder unsicherer, noch sicherer ist als der Umgang mit anderen Brenngasen. Basis für den sicheren Umgang mit Wasserstoff ist immer eine Risikoanalyse. N2 - In the DECHEMA Virtual Talks, general aspects of the safety and acceptance of hydrogen technologies were presented. How can trust in new technologies be built when past accidents led to myths and fairy tales? The presentation does away with general prejudices and shows that handling hydrogen is neither more unsafe nor safer than handling other fuel gases. The basis for the safe handling of hydrogen is always a risk analysis. T2 - DECHEMA Virtual Talks CY - Online meeting DA - 23.11.2020 KW - Hydrogen KW - Wasserstoff KW - Safety KW - Sicherer Umgang KW - Sicherheit PY - 2020 AN - OPUS4-52082 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mair, Georg A1 - Thomas, Sebastian A1 - Schalau, Bernd A1 - Wang, Bin T1 - Safety criteria for the transport of hydrogen in permanently mounted composite pressure vessels JF - International Journal of Hydrogen Energy; Special issue on the 8th International Conference on Hydrogen Safety (ICHS 2019) N2 - The recent growth of the net of hydrogen fuelling stations increases the demands to transport compressed hydrogen on road by battery vehicles or tube-trailers, both in composite pressure vessels. As a transport regulation, the ADR is applicable in Europe and adjoined regions, and is used for national transport in the EU. This regulation provides requirements based on the behaviour of each individual pressure vessel, regardless of the pressure of the transported hydrogen and relevant consequences resulting from generally possible worst case scenarios such as sudden rupture. In 2012, the BAM (German Federal Institute for Materials Research and Testing) introduced consequence-dependent requirements and established them in national transport requirements concerning the “UN service life checks” etc. to consider the transported volume and pressure of gases. This results in a requirement that becomes more restrictive as the product of pressure and volume increases. In the studies presented here, the safety measures for hydrogen road transport are identified and reviewed through a number of safety measures from countries including Japan, the USA and China. Subsequently, the failure consequences of using trailer vehicles, the related risk and the chance are evaluated. A benefit-related risk criterion is suggested to add to regulations and to be defined as a safety goal in standards for hydrogen transport vehicles and for mounted pressure vessels. Finally, an idea is given for generating probabilistic safety data and for highly efficient evaluation without a significant increase of effort. T2 - ICHS 2019 CY - Adelaide, Australia DA - 24.09.2019 KW - F-N-diagram KW - Chance-risk analysis KW - Pressure-volume product KW - Limit of acceptable consequence KW - Minimum burst pressure PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-511589 DO - https://doi.org/10.1016/j.ijhydene.2020.07.268 SN - 0360-3199 VL - 46 IS - 23 SP - 12577 EP - 12593 PB - Elsevier Ltd. AN - OPUS4-51158 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Munzke, Dorit A1 - Duffner, Eric A1 - Eisermann, René A1 - Schukar, Marcus A1 - Schoppa, André A1 - Szczepaniak, Mariusz A1 - Strohhäcker, J. A1 - Mair, Georg T1 - Monitoring of type IV composite pressure vessels with multilayer fully integrated optical fiber based distributed strain sensing JF - Materials Today: Proceedings N2 - We present the results of distributed fiber optic strain sensing for condition monitoring of a hybrid type IV composite fully wrapped pressure vessel using multilayer integrated optical fibers. Distributed strain sensing was performed for a total number of 252,000 load cycles until burst of the vessel. During this ageing test material fatigue could be monitored and spatially localized. Critical material changes were detected 17,000 cycles before material failure. Results have been validated by acoustic emission analysis. T2 - 12th International Conference on Composite Science and Technology (ICCST12) CY - Sorrento, Italy DA - 08.05.2019 KW - Hybrid composite pressure vessel KW - Distributed fiber optic sensing KW - Acoustic emission analysis KW - Structural health monitoring PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-516772 DO - https://doi.org/10.1016/j.matpr.2020.02.872 SN - 2214-7853 VL - 34 SP - 217 EP - 223 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-51677 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg A1 - Duffner, Eric A1 - Thomas, Sebastian T1 - Bergungsdruckgefäße - Vorschlag zur Definition von Druckgefäßen N2 - Es wird plastisch dargestellt, mit welcher Intention und welchem Ziel Deutschland in die Juni Sitzung des UN ECOSOC SubCom TDG gehen wird, um ein Druckvolumenbegrenzung für Druckgefäße zu erreichen. T2 - BAM-DIN-IGV-DVFG-Jahresgespräch 2020 CY - Berlin, Germany DA - 27.02.2020 KW - Bergungsdruckgefäß KW - Konsequenzbegrenzung KW - Volumenbegrenzung KW - Druck-Volumen-Produkt KW - UN-Modellvorschriften KW - Akzeptanz PY - 2020 AN - OPUS4-53146 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg T1 - Markthochlauf von Wasserstoff - Vertrauen durch probabilistische Sicherheitsbewertung der H2-Speicher N2 - Der Vortrag beginnt mit dem erwarteten Bedarf an Wasserstoff und der Frage der Risikosteuerung bei stattfindender Marktdurchsetzung. Dem gegenüber ist an einem Beispiel der Prozess der Regelsetzung gestellt, was die Notwendigkeit pro-aktiven Handelns zeigt. Es wird über die risikobasierte Definition von Sicherheit gezeigt, welche Bedeutung die Erfassung der Fertigungsstreuung hat und wie die quantitative Erfassung und Bewertung aussehen könnte. Zuletzt wird über den Aspekt der Alterung auf das Potential probabilistischer Zulassungsansätze verwiesen und aufgezeigt, wie die Wirkung von Vorschriften nach dem probabilistischen Sicherheitskriterium bewertet und optimiert werden kann. T2 - 9. HYPOS-Dialog: Grüner Wasserstoff, aber sicher! (Uni Magdeburg) CY - Magdeburg, Germany DA - 11.09.2020 KW - Wasserstoffspeicher KW - Monte-Carlo-Experiment KW - Lebensdauervorhersage KW - Statistische Bewertung KW - Sicherheit KW - Population PY - 2020 AN - OPUS4-53154 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Orellana Pérez, Teresa A1 - Mair, Georg A1 - Holtappels, Kai A1 - Maiwald, Michael A1 - Sobol, Oded T1 - Die Wasserstoffstrategie der BAM; Kompetenzzentrum H 2 safety@bam N2 - Das Thema Wasserstoff ist an der BAM seit mehr als hundert Jahren aktuell und steht auch gegenwärtig im Zentrum zahlreicher Forschungs- und Kooperationsaktivitäten. Mit der aktuellen Wasserstoff-Strategie der BAM werden wichtige Voraussetzungen dafür geschaffen, dass der Markthochlauf gelingt und die technische Sicherheit und Überwachung der Infrastrukturen und Anlagen gewährleistet ist – von der Erzeugung, über den Transport bis zur Speicherung und Bereitstellung von Wasserstoff als Energieträger der Zukunft. T2 - 1st Digital AK PostDocs Meeting CY - Online meeting DA - 01.10.2020 KW - Kompetenzzentrum H2Safety@BAM KW - Wasserstoff KW - Wasserstoffstrategie PY - 2020 AN - OPUS4-51371 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -