TY - JOUR A1 - Bloi, L. M. A1 - Hippauf, F. A1 - Boenke, T. A1 - Rauche, M. A1 - Paasch, S. A1 - Schutjajew, K. A1 - Pampel, Jonas A1 - Schwotzer, F. A1 - Dörfler, S. A1 - Althues, H. A1 - Oschatz, M. A1 - Brunner, E. A1 - Kaskel, S. T1 - Mechanistic insights into the reversible lithium storage in an open porous carbon via metal cluster formation in all solid-state batteries N2 - Porous carbons are promising anode materials for next generation lithium batteries due to their large lithium storage capacities. However, their highsloping capacity during lithiation and delithiation as well as capacity fading due to intense formation of solid electrolyte interphase (SEI) limit their gravimetric and volumetric energy densities. Herein we compare a microporous carbide-derived carbon material (MPC) as promising future anode for all solid-state batteries with a commercial high-performance hard carbon anode. The MPC obtains high and reversible lithiation capacities of 1000 mAh g−1carbon in half-cells exhibiting an extended plateau region near 0 V vs. Li/Li+ preferable for full-cell application. The well-defined microporosity of the MPC with a specific surface area of >1500 m2 g−1 combines well with the argyrodite-type electrolyte (Li6PS5Cl) suppressing extensive SEI formation to deliver high coulombic efficiencies. Preliminary full-cell measurements vs. nickel-rich NMC-cathodes (LiNi0.9Co0.05Mn0.05O2) provide a considerably improved average potential of 3.76 V leading to a projected energy density as high as 449 Wh kg−1 and reversible cycling for more than 60 cycles. 7Li Nuclear Magnetic Resonance spectroscopy was combined with ex-situ Small Angle X-ray Scattering to elucidate the storage mechanism of lithium inside the carbon matrix. The formation of extended quasi-metallic lithium clusters after electrochemical lithiation was revealed. KW - All solid-state battery KW - Microporous carbon KW - Lithium battery KW - Anode PY - 2022 DO - https://doi.org/10.1016/j.carbon.2021.11.061 SN - 0008-6223 VL - 188 SP - 325 EP - 335 PB - Elsevier Ltd. AN - OPUS4-54079 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fahmy, Alaa A1 - Kolmangadi, Mohamed Aejaz A1 - Schönhals, Andreas A1 - Friedrich, J. T1 - Structure of plasma‐deposited copolymer films preparedfrom acrylic acid and styrene: Part III sulfonation andelectrochemical properties N2 - Acrylic acid-styrene copolymer films were deposited plasma-chemically more gently using the pulsed plasma mode instead of the continuous mode, with linear and some slightly branched chains and marginal crosslinking. Then, the styrene unit of copolymers was wet-chemically sulfonated by chlorosulfuric acid. On exposure to air, the formed 4-chlorosulfonic acid groups hydrolyze to sulfonic acid groups (-SO3H). FTIR, XPS and broadband dielectric spectroscopy were employed to characterize the composition, the structure, the functional groups, and the electrochemical performance for the copolymers. A high concentration of sulfonic acid-containing groups was obtained in the sulfonated PS sample. The values of the DC conductivity DC for the sulfonated sample of the AA/S copolymer are ca. five orders of magnitude higher than that of the not-sulfonated copolymer materials. KW - Plasma Polymers KW - Electrolyte membrane PY - 2022 DO - https://doi.org/10.1002/ppap.202100222 SP - 1 EP - 12 PB - Wiley VHC-Verlag AN - OPUS4-54539 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tschirschwitz, Rico A1 - Bernardy, Christopher T1 - Meilensteintreffen BMBF-Vorhaben SEE-2L, Teilvorhaben BAM: Aufbau eines Großversuchsstandes N2 - Der Vortrag stellt den aktuellen Bearbeitungsstand des Teilvorhabens an der BAM dar. Neben dem eigentlichen Aufbau werden auch Herausforderungen bei der Beschaffung der Einzelkomponenten sowie Ergebnisse aus der Literaturrecherches zu den Auswirkungen von Li-Batteriespeichern beim thermischen Durchgehen vorgestellt. Als Abschluss wird noch ein Ausblick auf die anstehenden Probeversuche gegeben. T2 - Meilensteintreffen zum BMBF-Vorhaben SEE-2L (Sicherheit elektrochemischer Energiespeicher in Second Life Anwendungen) CY - Online meeting DA - 01.02.2022 KW - Stationäre Energiespeicher KW - Elektrische Energiespeicher KW - Auswirkungsbetrachtungen PY - 2022 AN - OPUS4-54572 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wahab, M. A. A1 - Kebelmann, Katharina A1 - Schartel, Bernhard A1 - Griffiths, G. T1 - Valorization of macroalgae digestate into aromatic rich bio-oil and lipid rich microalgal biomass for enhanced algal biorefinery performance N2 - The valorization of macroalgae digestate as a secondary resource for high value chemicals and nutrients will promote the sustainability and circularity of anaerobic digestion based biorefinery. In this study, three digestates from A. nodosum C.linum and L. digitata were separated into liquid and solid fractions to investigate the production of high value added chemicals through pyrolysis using Pyrolysis Gas Chromatography Mass Spectroscopy (Py-GC/MS) while the filtered liquid fractions were tested as an alternative culture media to grow C. sorokiniana under mixotrophic conditions. The digestates showed different thermal degradation and an improvement of bio-oil profiles compared to the starter material. Pyrolyzates from raw macroalgae were characterized by a high anhydrosugar content in contrast to high aromatics observed in the case of their digestates. Toluene, benzofuran and vinylphenol, base chemicals for many industries, represented together 30–37% of the total chemicals produced during pyrolysis of the three macroalgae digestate. On the other hand, C. sorokiniana cultured on digestate-based media showed a higher lipid content with an increase in monounsaturated fatty acids and a lower poly-unsaturated fatty acid content in comparison to microalgae grown in standard tris-acetate-phosphate media. Thus, the acyl composition was shifted in a direction more suitable for biodiesel production by this process. In addition, the increase of Chemical Oxygen Demand and Volatile Fatty Acids concentration in the digestate was found to reduce ammonium toxicity. Finally, 94% of Chemical Oxygen Demand and 83% of ammonium were removed by microalgae from the digestate-based media which will reduce the pollution risk of the biorefinery. Overall, the results indicate that using macroalgae solid digestates can generate improvements in the quality of products obtained by pyrolysis and the liquid digestate can positively influence microalgae growth and its products. KW - Macroalgae KW - Anaerobic digestion KW - Aromatics KW - Microalgae culture KW - Biorefinery PY - 2022 DO - https://doi.org/10.1016/j.jclepro.2022.130925 SN - 0959-6526 VL - 341 SP - 1 EP - 10 PB - Elsevier Ltd. AN - OPUS4-54365 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Frisch, M. A1 - Raza, M. H. A1 - Ye, M.-Y. A1 - Sachse, René A1 - Paul, B. A1 - Gunder, R. A1 - Pinna, N. A1 - Kraehnert, R. T1 - ALD-coated mesoporous iridium-titanium mixed oxides: Maximizing iridium utilization for an outstanding OER performance N2 - With the increasing production of renewable energy and concomitant depletion of fossil resources, the demand for efficient water splitting electrocatalysts continues to grow. Iridium (Ir) and iridium oxides (IrOₓ) are currently the most promising candidates for an efficient oxygen evolution reaction (OER) in acidic medium, which remains the bottleneck in water electrolysis. Yet, the extremely high costs for Ir hamper a widespread production of hydrogen (H₂) on an industrial scale. Herein, the authors report a concept for the synthesis of electrode coatings with template-controlled mesoporosity surface-modified with highly active Ir species. The improved utilization of noble metal species relies on the synthesis of soft-templated metal oxide supports and a subsequent shape-conformal deposition of Ir species via atomic layer deposition (ALD) at two different reaction temperatures. The study reveals that a minimum Ir content in the mesoporous titania-based support is mandatory to provide a sufficient electrical bulk conductivity. After ALD, a significantly enhanced OER activity results in dependency of the ALD cycle number and temperature. The most active developed electrocatalyst film achieves an outstanding mass-specific activity of 2622 mA mg(Ir)⁻¹ at 1.60 V(RHE) in a rotating-disc electrode (RDE) setup at 25 °C using 0.5 m H₂SO₄ as a supporting electrolyte. KW - Acidic oxygen evolution reaction KW - Atomic layer deposition KW - Electrocatalysis KW - Iridium oxide KW - Soft-templated mesoporous films PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-542651 DO - https://doi.org/10.1002/admi.202102035 SN - 2196-7350 SP - 1 EP - 11 PB - Wiley-VCH CY - Weinheim AN - OPUS4-54265 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rütters, H. A1 - Fischer, S. A1 - Le, Quynh Hoa A1 - Bettge, Dirk A1 - Bäßler, Ralph A1 - Maßmann, J. A1 - Ostertag-Henning, C. A1 - Wolf, J. L. A1 - Pumpa, M. A1 - Lubenau, U. A1 - Knauer, S. A1 - Jaeger, P. A1 - Neumann, A. A1 - Svensson, K. A1 - Pöllmann, H. A1 - Lempp, C. A1 - Menezes, F. F. A1 - Hagemann, B. T1 - Towards defining reasonable minimum composition thresholds – Impacts of variable CO2 stream compositions on transport, injection and storage N2 - To set up recommendations on how to define “reasonable minimum composition thresholds” for CO2 streams to access CO2 pipeline networks, we investigated potential impacts of CO2 streams with different and temporally variable compositions and mass flow rates along the CCS chain. All investigations were based on a generic “CCS cluster scenario” in which CO2 streams captured from a spatial cluster of eleven emitters (seven fossil-fired power plants, two cement plants, one refinery and one steel mill) are collected in a regional pipeline network. The resulting CO2 stream (19.78 Mio t impure CO2 per year) is transported in a trunk line (onshore and offshore) and injected into five generic replicate storage structures (Buntsandstein saline aquifers) offshore. Experimental investigations and modeling of selected impacts revealed beneficial as well as adverse impacts of different impurities and their combinations. Overall, no fundamental technical obstacles for transporting, injecting and storing CO2 streams of the considered variable compositions and mass flow rates were observed. We recommend to define minimum composition thresholds for each specific CCS project through limiting i) the overall CO2 content, ii) maximum contents of relevant impurities or elements, iii) acceptable variability of concentrations of critical impurities, and defining impurity combinations to be avoided. KW - Impurities KW - CO2 quality KW - Pipeline network KW - Whole-chain CCS scenario KW - Recommendations PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-543004 DO - https://doi.org/10.1016/j.ijggc.2022.103589 SN - 1750-5836 VL - 114 SP - 1 EP - 14 PB - Elsevier CY - New York, NY AN - OPUS4-54300 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hicke, Konstantin T1 - Monitoring von Strukturverhalten mittels integrierter verteilter faseroptischer Sensorik - Verteilte akustische Sensorik (DAS) N2 - Die verteilte faseroptische akustische Sensorik (DAS) wird vorgestellt, hinsichtlich ihrer Leistungsfähigkeit beschrieben und verschiedenste Anwendungsfelder, z.B. für das Zustandsmonitoring oder für seismische Messungen, beispielhaft gezeigt. Zudem werden mögliche Anwendungsfelder von DAS für den Kontext Kerntechnische Entsorgung (KTE) und Rückbau aufgezeigt. T2 - Online-Workshop „Dauerhafte Verschlussbauwerke für Endlager“ CY - Online meeting DA - 14.02.2022 KW - Verteilte faseroptische Sensorik KW - Verteilte akustische Sensorik KW - DAS KW - KTE KW - Monitoring Endlager PY - 2022 AN - OPUS4-54348 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simbruner, Kai T1 - Embrittlement of Spent Fuel Claddings - Micromechanically Motivated Cohesive Zone Modelling N2 - Since cladding acts as the first barrier for nuclear fuel, it is key to understand the degrading mechanisms leading to cladding embrittlement. Zirconium alloy based cladding samples subjected to simulated pre-storage drying conditions have shown high susceptibility to brittle failure under the occurrence of hoop stress and low temperature as expected after long-term interim storage. The stress state associated with a compressive pinch-load scenario is reproduced by the Ring Compression Test (RCT), which results in sudden failure at relatively small mechanical loads with high sensitivity to the presence of radial hydrides. As part of the BAM research project BRUZL (Fracture mechanics analysis of spent fuel claddings during long-term dry interim storage), static RCTs were conducted on non-irradiated, pre-hydrided ZIRLO® ring-shaped samples that were subjected to a radial hydride treatment. All samples failed in macroscopically brittle fashion with sudden load drops and severe crack propagation through almost the entire wall thickness. In a post-RCT examination of the fracture surfaces using scanning electron microscopy, radial hydrides could be identified as the weakest link of the structure. However, the microscopic failure mechanism is much more complex due to cracks initiating at different axial positions in depth direction of the ring, overlapping cracks, and arresting cracks. A considerable portion of the fracture surfaces appeared to have undergone plastic deformation of the zirconium matrix resulting in void growth and coalescence associated with ductile failure. The geometry of the ductile patches was measured, and the ductile surface fraction was determined. Based on these observations, a statistical model was developed that can reproduce the composition of the fracture surface as a one-dimensional projection. A micromechanically motivated cohesive zone model (CZM) was implemented in existing RCT finite element analysis (FEA) models with different constitutive laws for brittle hydrides and ductile matrix respectively. In this work, FEA results are presented for non-irradiated ZIRLO® and high-burnup M5® claddings. The impact of varying hydride-matrix combinations is discussed. Acknowledgement: The project was funded by the former Federal Ministry for Economic Affairs and Energy (BMWi) under contract no. 1501561. T2 - 6th GRS Workshop on the Safety of Extended Dry Storage of Used Nuclear Fuel CY - Garching, Germany DA - 01.06.2022 KW - Ageing Management KW - Cladding Embrittlement KW - Extended Storage KW - Ring Compression Test KW - Spent Nuclear Fuel PY - 2022 AN - OPUS4-55023 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Asna Ashari, Parsa A1 - Blind, K. ED - Jakobs, K. ED - Kim, D.-h. T1 - The Impact of Publications, Patents, and Standards on International Trade - The Case of Hydrogen N2 - Hydrogen as a clean energy carrier has received increased attention due to climate change and the need to introduce new, low-emissions technologies to the market. However, the drivers of increased hydrogen use have been barely explored. Therefore, this research paper investigates the impacts of publications, patents, and standards on international hydrogen trade, an established technology diffusion channel. In a fixed-effects (FE) regression model covering 37 countries between 1995 and 2020, we demonstrate that publications, patents, and standards are associated with increased levels of hydrogen exports and imports. Furthermore, we test the technology gap theory and explore the meaning of our empirical results for the hydrogen technological innovation system (TIS). Among others, we show that publications, patents, and standards can contribute to a more developed hydrogen TIS. T2 - 26th EURAS Annual Standardisation Conference – Standards for Digital Transformation: Blockchain and Innovation CY - Glasgow, Great Britain DA - 08.06.2022 KW - Hydrogen Trade KW - Publications KW - Patents KW - Standards KW - Technological Innovation System KW - Technology Gap Theory PY - 2022 SN - 978-3-95886-446-7 SP - 25 EP - 44 PB - Verlag Mainz CY - Mainz AN - OPUS4-55061 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Asna Ashari, Parsa T1 - The Impact of Publications, Patents, and Standards on International Trade - The Case of Hydrogen N2 - Hydrogen as a clean energy carrier has received increased attention due to climate change and the need to introduce new, low-emissions technologies to the market. However, the drivers of increased hydrogen use have been barely explored. Therefore, this research paper investigates the impacts of publications, patents, and standards on international hydrogen trade, an established technology diffusion channel. In a fixed-effects (FE) regression model covering 37 countries between 1995 and 2020, we demonstrate that publications, patents, and standards are associated with increased levels of hydrogen exports and imports. Furthermore, we test the technology gap theory and explore the meaning of our empirical results for the hydrogen technological innovation system (TIS). Among others, we show that publications, patents, and standards can contribute to a more developed hydrogen TIS. T2 - 26th EURAS Annual Standardisation Conference – Standards for Digital Transformation: Blockchain and Innovation CY - Glasgow, United Kingdom DA - 08.06.2022 KW - Hydrogen Trade KW - Publications KW - Patents KW - Standards KW - Technological Innovation System KW - Technology Gap Theory PY - 2022 AN - OPUS4-55062 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bischoff, Tristan T1 - Testing and evaluating norms for hot water storage tank efficiency N2 - Überprüfung der aktuell gesetzlich festgeschriebenen Prüfnormen (EN 12977, EN 12897) zur Wärmeverlustmessung von Warmwasserspeichern mit Hilfe eines Ringversuchs mit fünf Laboren. T2 - Conference of young scientists on energy and natural science issues CY - Kaunas, Lithuania DA - 24.5.2022 KW - Heat storage KW - Standing Losses KW - Round Robin Trial KW - Statistical Analysis KW - NAPE-Project KW - Energy-Label PY - 2022 UR - https://vimeo.com/710278130/8fae7db4d5 AN - OPUS4-55050 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachau, Andre T1 - BAM Test method for heat pumps and Air conditioners N2 - The Federal Institute for Materials Research and Testing (BAM) has developed a load-based test method (compensation method) to determine the energy efficency of heat pumps and air conditioners. The method allows for testing with unfixed compressor speed and active control of the unit. Thus, at low part loads the unit under test is allowed to cycle on-off, when the frequency of the compressor drops below its minimum threshold. Therefore, the associated efficiency losses are directly measured and correction calculations as for the current steady state tests become obsolete. In addition, the testing can be performed without the support of the manufacturer by market surveillance authorities, for instance, since no frequency and expansion valve settings are required. To prove that the compensation method is repeatable and reproducible three round robin tests have been organised by BAM. T2 - Informal Meeting of ISO/TC 86/SC 6/TG 13 CY - Online meeting DA - 09.12.2021 KW - Heat pump KW - Air conditioner KW - Load-based testing KW - Energy efficiency KW - Compensation method PY - 2022 AN - OPUS4-54848 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn T1 - Ultrakurzpulslaser induzierte Oxidschichten zur Reduktion von Reibung und Verschleiß auf Metalloberflächen N2 - Die Reduktion von Reibung und Verschleiß in technischen Systemen bietet ein großes Potenzial zur Reduktion von CO2-Emissionen. Dieser Beitrag diskutiert die Erzeugung und tribologische Charakterisierung von Ultrakurzpuls-generierten Nano- und Mikrostrukturen auf Metallen (Stahl, Titan). Besonderes Augenmerk wird dabei auf die Rolle der laserinduzierten Oxidschicht im Zusammenspiel mit verschleißreduzierenden Additiven in ölbasierten Schmiermitteln gerichtet. T2 - Workshop "Nachhaltigkeit durch Tribologische Schichten" - Europäische Forschungsgesellschaft Dünne Schichten e.V. CY - Karlsruhe, Germany DA - 17.05.2022 KW - Laser-induzierte periodische Oberflächenstrukturen KW - Reibungsreduktion KW - Verschleißreduktion KW - Oberflächenmodifikation KW - Oxidation KW - Additive PY - 2022 AN - OPUS4-54849 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trappe, Volker T1 - Dynamic mechanical analysis of epoxy-matrix cross linking measured in-situ using an elastomer container N2 - A new patented dynamic mechanical analysis (DMA) is presented, where the tensile, bending- or torsional stiffness of a media can be characterized in-situ during the phase transition from liquid to solid. An epoxy system, e.g. Hexion L285/H287, is filled into an elastomer container, such as a silicone tube. This can be mounted into a conventional DMA and, based on a linear viscoelastic approach, the storage modulus (E’;G’), the loss modulus (E’’;G’’) and the loss angle tan(delta) can be measured at constant temperature as a function of time in order to investigate the liquid to sol-gel to solid transition. With this new method, the stiffness increase as a result of the cure process can be directly measured more precisely than with a rheometer in a shear plate set-up, because using an elastomer container gives a defined cross section for calculating the Young’s modulus. T2 - 20th European Conference on Composite Materials, ECCM20 CY - Lausanne, Switzerland DA - 26.06.2022 KW - Dynamic mechanical analysis (DMA) KW - Thermoset polymers KW - Cure process KW - Cross linking PY - 2022 AN - OPUS4-55213 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tschirschwitz, Rico T1 - Projekte und Aktivitäten zu Elektrischen Energiespeichern an der BAM N2 - Die Sicherheit von Lithiumbatterien ist ein entscheidender Punkt beim Ausbau der Elektromobilität. Der Beitrag gibt zunächst einen Überblick über das Aktivitätsfeld der elektrischen Energiespeicher an der BAM. Im weiteren werden sowohl die Projekte HaCLIB (Hazard Classification ofLithium-Ion Batteries) als auch SEE-2L (Sicherheit elektrochemischer Energiespeicher in 2nd-Life Anwendung) vorgestellt. Darüber hinaus werden noch die hoheitlichen Aufgaben der BAM im Bereich des Transports von kritisch defekten Batterien erläutert. T2 - Sitzung des ProcessNet-AA Reaktionstechnik sicherheitstechnisch schwieriger Prozesse (AA-RTSSP) der DECHEMA CY - Online meeting DA - 13.04.2022 KW - Stationäre Energiespeicher KW - Elektrische Energiespeicher KW - Auswirkungsbetrachtungen KW - EES PY - 2022 AN - OPUS4-54649 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn T1 - Laser-Induced Periodic Surface Structures: when Maxwell meets Marangoni N2 - Laser-Induced Periodic Surface Structures (LIPSS, ripples) are a universal phenomenon and can be generated in a contactless, single-step process on almost any material upon irradiation of solids with intense laser radiation. Nowadays, processing rates of up to m^2/min are enabling new industrial applications in medicine, optics, tribology, biology, etc. Depending on the specific type of LIPSS, their structural sizes typically range from several micrometers down to less than 100 nanometers – far beyond the optical diffraction limit – while their orientations exhibit a clear correlation with the local polarization direction of the laser radiation. From a theoretical point of view, however, a controversial and vivid debate has emerged during the last two decades, whether LIPSS originate from electromagnetic effects (seeded already during the laser irradiation) – or whether they emerge from matter reorganization processes, i.e. distinctly after the laser irradiation. This presentation reviews the currently existent theories of LIPSS. A focus is laid on the historic development of the fundamental ideas, their corresponding mathematical descriptions and numerical implementations, along with a comparison and critical assessment of the different approaches. T2 - 16th International Conference on Laser Ablation (COLA 2021/22) CY - Matsue, Japan DA - 24.04.2022 KW - Laser-induced periodic surface structures (LIPSS) KW - Laser ablation KW - Theoretical modelling KW - Electromagnetic scattering KW - Hydrodynamics PY - 2022 AN - OPUS4-54716 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska T1 - Charakterisierung von Salzbeton und alkali-aktivierten Material basierend auf der Schallemissionsanalyse N2 - Nach einer kurzen Einführung in die Schallemissionsprüfung und -Analyse wird ein Versuchsstand vorgestellt, der im Rahmen des Themenfeldprojektes Seal Waste Safe installiert wurde. Schwerpunkt des Vortrages sind die Schallemissionsmessungen an einem 150 l Demonstrator aus Salzbeton und einem weiteren aus alkali-aktiviertem Material. Neben der konventionellen Schallemissionsanaylse mit Aktivitäts- und Intensitätsparametern der Zeitsignale, werden auch frequenzbasierte Parameter zur Analyse andiskutiert. N2 - After a brief introduction to acoustic emission testing and analysis, an experimental test setup is presented, which was part of the Seal Waste Safe project (internal BAM project 2019-2022). Herein, the acoustic emission measurements of a 150 l demonstrator made of salt concrete and another one made of alkali-activated material are focused. In addition to the conventional acoustic emission analysis regarding the activity and intensity parameters of the detected time signals, also frequency-based parameters were discussed for analysis. T2 - Dauerhafte Verschlussbauwerke für Endlager CY - Online meeting DA - 14.2.2022 KW - Acoustic Emission KW - Schallemission KW - Salzbeton KW - Alkali aktiviertes Material KW - Geopolymer PY - 2022 AN - OPUS4-54937 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stamm, Michael A1 - Krankenhagen, Rainer T1 - Weather-dependent passive thermography of unheated wind turbine blades N2 - Up to now, the inspection of wind turbines with industrial climbers has been considered ”state of the art”. However, ever-larger wind turbines and advancing digitization make modern and automated inspection methods indispensable. Passive thermography can serve as such a digital and atomized method while it is well known for its applications in the inspection of buildings or electrical circuits. However, its application relies on thermal gradients in the inspected object such that a temperature contrast exists between damaged and sound areas. This also holds for unheated structures like rotor blades of wind turbines which show no intrinsic temperature gradient and can hardly be heated. Under certain weather conditions with sufficient solar loading and diurnal temperature variations, passive thermography is suitable for the in-service inspection of rotor blades. However, for a reliable use of passive thermography on ”thermal passive” components, the incorporation of these environmental conditions in the planning and evaluation of thermal inspections is crucial. Additionally, the complex inner structure of wind turbine blades in comparison to other objects and buildings require a specific method referencing the individual rotor blades to each other. This allows the distinction between the thermal response of design-specific structural features and damages or irregularities between the three blades. We show thermal signatures of damage in rotor blades and contrast them with structural characteristics by comparing the three blades. In addition to measurements in industrial environments, laboratory measurements are shown and compared to simulations. The long-term goal is to simulate the influence of different weather parameters and thus gain a better understanding of measurements in the field. The results shown here can be seen as one step towards industrial application. T2 - SPIE Defense + Commercial Sensing CY - Orlando, Florida, USA DA - 03.04.2022 KW - Passive thermography KW - Wind energy KW - FEM simulations PY - 2022 DO - https://doi.org/10.1117/12.2618740 VL - 12109 SP - 1 EP - 8 PB - Society of Photo-Optical Instrumentation Engineers (SPIE) AN - OPUS4-54943 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stamm, Michael T1 - Weather-dependent passive thermography of unheated wind turbine blades N2 - Up to now, the inspection of wind turbines with industrial climbers has been considered ”state of the art”. However, ever-larger wind turbines and advancing digitization make modern and automated inspection methods indispensable. Passive thermography can serve as such a digital and atomized method while it is well known for its applications in the inspection of buildings or electrical circuits. However, its application relies on thermal gradients in the inspected object such that a temperature contrast exists between damaged and sound areas. This also holds for unheated structures like rotor blades of wind turbines which show no intrinsic temperature gradient and can hardly be heated. Under certain weather conditions with sufficient solar loading and diurnal temperature variations, passive thermography is suitable for the in-service inspection of rotor blades. However, for a reliable use of passive thermography on ”thermal passive” components, the incorporation of these environmental conditions in the planning and evaluation of thermal inspections is crucial. Additionally, the complex inner structure of wind turbine blades in comparison to other objects and buildings require a specific method referencing the individual rotor blades to each other. This allows the distinction between the thermal response of design-specific structural features and damages or irregularities between the three blades. We show thermal signatures of damage in rotor blades and contrast them with structural characteristics by comparing the three blades. In addition to measurements in industrial environments, laboratory measurements are shown and compared to simulations. The long-term goal is to simulate the influence of different weather parameters and thus gain a better understanding of measurements in the field. The results shown here can be seen as one step towards industrial application. T2 - Defense + Commercial Sensing 2022 CY - Orlando, Florida, USA DA - 3.4.2022 KW - Passive thermography KW - Wind energy KW - FEM simulations PY - 2022 UR - https://spie.org/defense-commercial-sensing/presentation/Weather-dependent-passive-thermography-of-unheated-wind-turbine-blades/12109-19?SSO=1 AN - OPUS4-54944 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wille, Frank T1 - CASTOR in Warteposition, aber bitte sicher. N2 - CASTOR-Behälter sollen den Auswirkungen schwerster Unfälle standhalten und müssen dabei ihre Sicherheitsfunktionen beibehalten. Dazu zählen der sichere Einschluss des radioaktiven Inventars mit nachgewiesener Behälterintegrität und -dichtheit, die ausreichende Abschirmung der radioaktiven Strahlung, die Ableitung der von den Brennelementen ausgehenden Wärme und der Ausschluss des Entstehens einer nuklearen Kettenreaktion, d.h. die Kritikalitätssicherheit sind zu gewährleisten. Zum Nachweis dieser Fähigkeiten werden die Behälter gegen Stoß, Aufprall, Durchstoßen, Feuer sowie beim Eintauchen in Wasser geprüft. Durch diese Tests werden Beanspruchungen aus potentiellen schweren Unfällen abdeckend simuliert. Die hierfür erforderlichen experimentellen Tests, aber auch die Prüfung und Entwicklung komplexer rechnerischer Simulationen des Behälterverhaltens unter Anwendung der Finite-Elemente-Methode erfolgen bei der Bundesanstalt für Materialforschung und -prüfung (BAM). Die Basis bildet das Regelwerk der Internationalen Atom- und Energieorganisation (IAEO) zum sicheren Transport von radioaktiven Stoffen, welches international harmonisierte Schutzziele und Prüfanforderungen definiert. Die seit 60 Jahren praktizierte stetige Weiterentwicklung der Sicherheitsanforderungen trägt aktuellen Erkenntnissen, Erfahrungen und Risikoanalysen Rechnung. Die Brennelementbehälter werden mechanischen Prüfungen sowie Brand- und Wasserdruckprüfungen unterzogen. Hierdurch wird nachgewiesen, dass sie den Auswirkungen eines schweren Unfalls standhalten können. Nur Behälter die zweifelsfrei die kumulativen mechanischen und thermischen Tests und auch die Wasserdruckprüfung mit Erfüllen aller Schutzziele bestehen, bekommen eine Zulassung, die es erlaubt die Behälter zu transportieren. KW - Kerntechnik KW - Radioaktive Stoffe KW - Transport KW - Zwischenlagerung KW - IAEA KW - Fallprüfung PY - 2022 DO - https://doi.org/10.26125/73hj-nz53 SN - 1611-9479 VL - 24 IS - 3 SP - 112 EP - 114 PB - Bunsen-Gesellschaft CY - Frankfurt AN - OPUS4-54856 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Amano, K. A1 - Hahn, S. A1 - Tschirschwitz, Rico A1 - Rappsilber, Tim A1 - Krause, U. T1 - An Experimental Investigation of Thermal Runaway and Gas Release of NMC Lithium-Ion Pouch Batteries Depending on the State of Charge Level N2 - In this study, 19 experiments were conducted with 25 pouch cells of NMC cathode to investigate thermal runaway and the release of gases from lithium-ion batteries (LIBs). Single cells, double cells, and a four-cell battery stack were forced to undergo thermal runaway inside an air-tight reactor vessel with a volume of 100 dm3 . The study involved two series of tests with two types of ignition sources. In the Series 1 tests, a heating plug was used to initiate thermal runaway in LIBs in the ranges of 80–89% and 90–100% SOC. In the Series 2 tests, a heating plate was used to trigger thermal runaway in LIBs in the ranges of 30–50%, 80–89%, and 90–100% SOC. Thermal runaway started at an onset temperature of 344 ± 5 K and 345 K for the Series 1 tests and from 393 ± 36 K to 487 ± 10 K for the Series 2 tests. Peak reaction temperatures ranged between 642 K and 1184 K, while the maximum pressures observed were between 1.2 bar and 7.28 bar. Thermal runaway induced explosion of the cells and lead to a rate of temperature increase greater than 10 K/s. The amounts of gases released from the LIBs were calculated from pressures and temperatures measured in the reactor. Then, the gas composition was analyzed using a Fourier transform infrared (FTIR) spectrometer. The highest gaseous production was achieved at a range of 90–100% SOC and higher battery capacities 72 L, 1.8 L/Ah (Series 1, battery stack) and 103 L, 3.2 L/Ah (Series 2, 32 Ah cell)). Among the gases analyzed, the concentration of gaseous emissions such as C2H4 , CH4 , and C2H6 increased at a higher cell capacity in both series of tests. The study results revealed characteristic variations of thermal behavior with respect to the type of ignition source used. KW - Lithium-ion batteries KW - Battery KW - Pouch cell KW - NMC Cathode KW - Thermal runaways PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-548601 DO - https://doi.org/10.3390/batteries8050041 VL - 8 IS - 5 SP - 1 EP - 16 PB - MDPI CY - Basel, Switzerland AN - OPUS4-54860 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ghafafian, Carineh T1 - Fully-reversed fatigue behavior of scarf joint repairs for wind turbine blade shell applications N2 - Due to manufacturing imperfections which can propagate to damage under in-service loads, wind turbine rotor blades, made primarily of glass fiber reinforced polymers (GFRP), often fail significantly before their design life. To enable a quick and cost-effective return to service, localized repairs can be executed by technicians in the field, directly accessing the blades by suspended roping. Scarf joint repairs, shown to be highly efficient with a smooth load transition across angled joint walls and a restored aerodynamic profile, are the focus of this study. The damage mechanisms of these structures were examined under fully-reversed mechanical cyclic loading with a load ratio R = -1, which was made possible on the coupon scale by a custom designed anti-buckling support. The number of cycles to failure were compared across load levels. While the scarf joint ratio was held constant at 1:50, known from industry and literature to be a good compromise between restored mechanical properties and repair size, the layup sequence was varied between small-to-large and large-to-small. Hereby the effect of the presence of resin pockets and fiber orientation mismatch between the parent and repair structure on the failure mechanism as well as fatigue strength of ±45° GFRP scarf joint repair structures was studied. Strain development across the joint length was measured to assess stiffness degradation in addition to the fatigue strength recovery of scarf joint structures with respect to pristine reference specimens. Grayscale analysis was used to monitor the damage state leading to fracture across the specimens. Post-mortem fractography analysis with light microscopy described the global failure mechanisms as well as local damage distribution within the structure, all of which provided insight to critical variables in scarf joint GFRP structures under fully-reversed mechanical cyclic loading, allowing for the tailoring of such repairs on wind turbine blade shells for maximum restoration of service life. T2 - 20th European Conference on Composite Materials (ECCM20) CY - Lausanne, Switzerland DA - 26.06.2022 KW - Glass fiber reinforced polymers KW - Scarf repairs KW - Fatigue PY - 2022 AN - OPUS4-55638 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zekhnini, Khalid T1 - Corrosion testing in a laboratory container: Corrosion testing with artificial seawater and sediment N2 - Electricity generation by offshore wind turbine generators (WTG) is an important pillar of the energy transition. Corrosion processes on WTGs pose a particular challenge with regard to safe operation over longer periods of time due to the highly corrosive conditions in the offshore area. BAM is therefore conducting research to ensure a safe operation of the turbines over their intended service life to protect people and the environment. In a joint research project, different corrosion-relevant areas of a WTG foundation structure were specifically simulated in test basins within a laboratory container. The aim of the work was, on the one hand, the gravimetric and electrochemical determination of corrosion rates in the different areas of an WTG that are relevant for cathodic corrosion protection (CCP): Underwater and sediment zone as well as the transition area between these two zones. Also, targeted tests were carried out under CCP. In addition, investigations regarding calcareous deposition during CCP were carried out on idealized specimens under laboratory conditions to better assess its influence on the protection process. The investigations were carried out in a laboratory container with different basins, which were filled with sand as sediment and artificial seawater according to ISO 15711and connected via a closed water circuit. The poster at EURCORR 2022 provides an overview of the investigations and the most important results. It will be evaluated, if a simulation of offshore corrosion conditions is possible to a certain extent in an idealized system with artificial seawater and sediment. T2 - EUROCORR 2022 CY - Berlin, Germany DA - 28.08.2022 KW - Corrosion KW - Corrosion Testing KW - Artificial Sea Water KW - Laboratory Container PY - 2022 AN - OPUS4-55664 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hicke, Konstantin T1 - Distributed fiber optic sensing @BAM N2 - Research and developement activities of BAM regarding Distributed Fiber Optic Sensing are portrayed using exemplary previous and current projects. Shown results pertain to distributed acoustic sensing (DAS), distributed temperagture sensing (DTS) and distributed strain sensing (DSS). T2 - Seismic seminar FU Berlin (group Prof. Shapiro) CY - Online meeting DA - 15.09.2022 KW - Distributed fiber optic sensing KW - Distributed acoustic sensing KW - Distributed temperature sensing KW - Distributed strain sensing KW - Infrastructure monitoring PY - 2022 AN - OPUS4-55721 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schönhals, Andreas T1 - Inelastic and Quasielastic Neutron Scattering Experiments on Mircroporous Membranes for Green Separation processes N2 - Polymers with intrinsic microporosity are promising candidates for the active separation layer in gas separation membranes. These polymers are characterized by a high permeability and reasonable permselectivity. The reasonable permselectivity of these materials is somehow surprising because for microporous systems a more Knudsen-like diffusion is expected rather than a size dependent temperature activated sieving process. It was argued in the framework of a random gate model that molecular fluctuations on a time scale from ps to ns are responsible for the permselectivity. Here a series of microporous polynorbornenes with bulky SiMe3 side groups and a rigid backbone is considered which have different microporosities characterized by BET surface area values. First inelastic time-of-flight neutron scattering measurements were carried out to investigate the low frequency density of state (VDOS). The measured data show the characteristic low frequency excess contribution to the VDOS above the Debye sound wave level, generally known as the Boson peak in glass-forming materials. It was found that the maximum position of the Boson peak correlates with the BET surface area. For two selected comparable polynorbornenes elastic scans as well as QENS measurements by a combination of neutron time-of-flight and backscattering were carried out. A low temperature relaxation process was found for both polymers. This process was assigned to the methyl group rotation. It was analysed in terms of a jump diffusion in a three-fold potential. The analysis of the dependence of the elastic incoherent structure factor on the scattering vector yields the number of methyl groups which might be immobilized. T2 - QENS / WINS 2022 CY - San Sebastian, Spain DA - 23.05.2022 KW - Polymers of intrinsic Microporosity PY - 2022 AN - OPUS4-55673 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schönauer-Kamin, Daniela T1 - Powder-Aerosol deposited (PAD) calcium manganate as n-type thermoelectric material N2 - Currently, calcium manganate CaMnO3 and calcium cobaltite Ca3Co4O9 are being investigated as n-type resp. p-type semiconducting materials as oxidation- and temperature-resistant thermoelectric materials for oxide multilayer thermoelectric generators (TEGs). In order to manufacture multilayer TEGs, pressure-assisted sintering processes at high temperatures are necessary to achieve optimal thermoelectric material properties. To realize TEGs in planar film technology, another method to obtain dense ceramic layers directly from the synthesized starting powders without a subsequent high temperature step is emerging recently: the powder aerosol deposition (PAD) method. In the present work, it is investigated whether PAD is suitable to produce dense ceramic films from Sm-doped CaMnO3 and Ca3Co4O9 powders. The resulting thermoelectric properties are characterized as a function of temperature. CaMnO3 powder could successfully be processed by PAD with resulting layer thicknesses of 5- 6 µm without any high-temperature sintering steps of the films. The electrical conductivity and the Seebeck coefficient of the films were determined in-plane from room temperature to 600 °C in air. The results show a Seebeck coefficient of around -200 µV/K, which is comparable to results of pressed and sintered bars. At 400 °C, the electrical conductivity corresponds to the conductivity of the bar. At higher temperatures the conductivity is better than with the reference. Below 400°C, the electrical conductivity is somewhat lower than that of the reference sample, a mild thermal treatment of the PAD layer improves it. It is expected that the thermal conductivity of the PAD film will be lower compared to the bars due to the nano-crystalline film morphology. This should result in a significantly increased ZT value for the PAD layers and a higher efficiency of the TEG. The work shows that both CaMnO3 and Ca3Co4O9 can be successfully processed by PAD, and the PAD films show comparable thermoelectric properties. T2 - 18th European Conference on Thermoelectrics CY - Barcelona, Spanien DA - 14.09.2022 KW - Film depositition KW - Calcium cobaltite PY - 2022 AN - OPUS4-55771 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stamm, Michael T1 - Towards automated passive thermography of wind turbine blades N2 - Up to now, the inspection of wind turbines by industrial climbers has been considered "state of the art". However, many aspects like ever-larger wind turbines, minimizing the risk for man and machine and the advancing digitalization make modern and automated inspection methods indispensable. A particular interest here is contactless and remote methods that can be used with drones instead of climbing robots. The work presented here contributes to the long-term goal of making autonomous and advanced inspections of wind turbine rotor blades using drones ready for industrial use. Besides visual inspection, only a few inspection methods are capable of non-contact inspection on an industrial scale. Passive thermography can serve as such a contactless and digital inspection method and is well known for its applications in the inspection of buildings or electrical circuits. It can even sense both near-surface and subsurface defects. The sensitivity to subsurface defects makes one advantage of thermography over visual inspections. As a digital inspection method, it is generally also more objective and offers more comparability. For example, defects and their extent can be easily monitored and compared over time. However, its industrial application relies on thermal gradients in the inspected object such that a temperature contrast exists between damaged and sound areas. This also applies to large unheated structures such as wind turbine rotor blades, which do not have an intrinsic temperature gradient and at the same time cannot be easily heated externally. Under certain weather conditions, a change of the environmental temperature or the solar loading conditions can provide the necessary thermal gradients to make passive thermography viable for the in-service inspection of rotor blades. For a reliable use of passive thermography on "thermal passive" components, the incorporation of these environmental conditions in the planning and evaluation of thermal inspections is crucial. Compared to many other objects and buildings, wind turbine blades have varying and often unknown complex internal structures depending on the model. A special method is therefore required, that can be used independently of the internal structure of the blades and that relates the individual thermograms of the three rotor blades to each other. This allows the distinction between the thermal response of design-specific structural features and damages or irregularities between the three blades. In this work we present thermal signatures of rotating in-service rotor blades taken under industrial relevant conditions. These thermograms show surface and subsurface damages and irregularities which we contrast with structural design features by referencing the three blades to each other. In addition, we examine the strong influence of different weather conditions on the inspection results. A direct comparison of measured results with inspection reports from industrial climbers serves as a benchmark. T2 - EERA DeepWind conference CY - Trondheim, Norway DA - 19.01.2022 KW - Thermography KW - Wind energy KW - Passve IR KW - Rotor blades KW - Maintenance PY - 2022 AN - OPUS4-55818 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stamm, Michael T1 - Towards the in-service blade inspection by ground-based passive thermography N2 - Until today, the optical inspection of rotor blades by industrial climbers is considered state of the art. However, both more and larger rotor blades and the increasing digitalization of maintenance work make modern inspection methods increasingly necessary. In this context, passive thermography can serve as a useful digital technique for in-service inspection of wind turbine blades. Unlike active thermography, this inspection method does not require an active heat source but takes advantage of heating by the sun and diurnal temperature fluctuations. This allows inspections from the ground during operation and does not require shutting down the wind turbine. However, an inspection with passive thermography is highly weather dependent. Thus, the already weak thermal signatures formed due to internal structures and possible internal damage are only strong enough under certain weather conditions. To obtain meaningful inspection results despite the relatively small thermal differences between intact and defective components, three aspects are crucial: 1. Measurements should be taken at the time of optimum weather conditions. It must be kept in mind that different internal damage will be revealed by thermal signatures under different weather conditions. 2. The thermal signature of the rotor blades, including possible damages, must be simulated with FEM simulations. In this way, the influence of different weather conditions can be predicted but also understood in the aftermath. 3. The temperature differences between identically designed and assembled rotor blades must be considered to analyze variations between blades. This work will address all these aspects and show, based on field measurements under industrial conditions (exemplarily shown in figure 1), laboratory measurements and FEM simulations, which steps must be taken to establish passive thermography as an industrial inspection method. T2 - EERA SP7 Rotor Blade workshop CY - Roskilde, Denmark DA - 23.06.2022 KW - Thermography KW - Wind energy KW - Maintenance KW - Rotor blades KW - Passive IRT PY - 2022 AN - OPUS4-55819 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Junge, P. A1 - Stargardt, Patrick A1 - Kober, D. A1 - Greinacher, M. A1 - Rupprecht, C. T1 - Thermally Sprayed Al2O3 Ceramic Coatings for Electrical Insulation Applications N2 - Thermal spraying enables a fast and propelling way to additively deposit various ceramics as electric insulators, which are used in conditions where polymers are not suitable. Alumina (Al2O3) is among the most employed materials in the coating industry since it exhibits good dielectric properties, high hardness, high melting point while still being cost-effective. Various parameters (e.g. feedstock type, plasma gas mixture, plasma power) significantly influence the resulting coating in terms of microstructure, porosity, crystallinity, and degree of un-or molten particles. As a consequence, these parameters need to be investigated to estimate the impact on the electrical insulating properties of thermally sprayed alumina. This study focuses on the development of a novel electric insulation coating from Al2O3 feedstock powders deposited via atmospheric plasma spray (APS). The microstructure, porosity, and corresponding crystallographic phases have been analyzed with optical microscopy, XRD, and SEM images. To achieve an understanding of the parameters influencing the electrical insulation performance of the manufactured coatings, an in-depth analysis of the fundamental dielectric parameters e.g., DC resistance, breakdown strength, dielectric loss tangent, permittivity is presented. T2 - International Thermal Spray Conference and Exposition 2022 CY - Vienna, Austria DA - 04.05.2022 KW - Thermal Spray KW - Alumina KW - Dielectric properties PY - 2022 SP - 1 EP - 8 AN - OPUS4-55821 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stamm, Michael T1 - In situ Charakterisierung von Reparaturen in GFK Schalenstrukturen mittels Lockin Thermografie und Felddehnungsmessungen N2 - Die tiefgreifende Reparatur von Faserverbundwerkstoffen stellt durch deren inneren Aufbau eine besondere Herausforderung dar, die unter anderem bei der Instandhaltung von Rotorblättern von Windkraftanlagen zum Tragen kommt. Um die Reparaturen von Rotorblattschalen zu untersuchen und zu optimieren, wurden an der BAM Sandwich-Schalenprüfkörper aus Glasfaserkunststoff (GFK) entwickelt. Nachdem in diese Schalenprüfkörper Modell-Reparaturen eingebracht wurden, werden zyklische mechanische Ermüdungsversuche bis zum Bruch durchgeführt. Vorrangiges Ziel ist es, den Einfluss verschiedener Reparaturvariablen auf die Ermüdungslebensdauer der Struktur zu verstehen, sowie die stabilste Reparaturmethode zu bestimmen. Während der zyklischen Lastversuche wurden regelmäßig in-situ Messungen mit einer Thermografie Kamera und einem optischen Felddehnungsmesssystem durchgeführt. Durch beide Messmethoden lassen sich Eigenschaften der Probekörper zeitlich und räumlich aufgelöst darstellen. Während die Felddehnungsmessungen Aufschluss über die Verformung an der Oberfläche geben, erfasst die thermische Inspektion Temperaturänderungen an der Oberfläche. Besonders die thermografischen Messwerte bilden hier das oberflächennahe Volumen ab, in dem sich Temperaturänderungen an der Oberfläche abzeichnen. Die Messergebnisse beider Systeme stellen also verschiede aber korrelierte Parameter dar. Denn die zyklische Belastung (Bewegung) ruft eine periodische Temperaturänderung im Bauteil hervor. Dieser so genannte Thermoeleastische Effekt kann durch eine Lockin-Analyse der Temperaturtransienten (Temperaturverläufe) nachgewiesen werden. Die räumliche Darstellung der thermischen Effekte lässt Rückschlüsse auf die tatsächliche Lastverteilung im Probekörpervolumen zu. Darüber hinaus führen nichtelastische Verformungen zu einer zusätzlichen Wärmefreisetzung, die durch geeignete Auswerteverfahren ebenfalls nachgewiesen werden können. Entsprechende Hot-Spots in der räumlichen Verteilung erlauben eine frühzeitige Erkennung besonders belasteter Bereiche lange vor dem eigentlichen Bauteil-Versagen. Das gestattet die Lokalisierung des Initial-Schadens, was mit der numerischen Spannungsanalyse korreliert werden kann und die Entwicklung und Bewertung verschiedener Reparaturstrategien. T2 - DGZfP Jahrestagung 2022 CY - Kassel, Germany DA - 23.05.2022 KW - Lockin Thermografie KW - GFK KW - NDT KW - ZfP PY - 2022 AN - OPUS4-55823 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn T1 - Laser-induced Periodic Surface Structures (LIPSS): Mechanisms, Applications, and unsolved Problems N2 - Laser-induced Periodic Surface Structures (LIPSS, ripples) are a universal phenomenon and can be generated in a contactless, single-step process on almost any type of solid upon irradiation with intense laser pulses. They represent a (quasi-)periodic modulation of the surface topography in the form of a linear grating and are typically formed in a “self-ordered” way in the focus of a laser beam. Thus, they are often accompanying laser material processing applications. The structural sizes of LIPSS typically range from several micrometers down to less than 100 nanometers – far beyond the optical diffraction limit – while their orientations exhibit a clear correlation with the local polarization direction of the laser radiation. From a theoretical point of view, a controversial debate has emerged during the last decades, whether LIPSS originate from electromagnetic effects (seeded already during the laser irradiation) – or whether they emerge from matter-reorganization processes (distinctly after the laser irradiation). From a practical point of view, however, LIPSS represent a simple and robust way for the nanostructuring of solids that allows creating a wide range of different surface functionalities featuring applications in optics, tribology, medicine, energy technologies, etc. While the currently available laser and scanner technology already allows surface processing rates at the m^2/min level, industrial applications of LIPSS are sometimes limited by the complex interplay between the nanoscale surface topography and the specific surface chemistry. This typically manifests in difficulties to control the processing of LIPSS and in limitations to ensure the long-term stability of the created surface functions. This presentation reviews the currently existent theories of LIPSS. A focus is laid on the historic development of the fundamental ideas behind the LIPSS, their corresponding mathematical descriptions and numerical implementations, along with a comparison and critical assessment of the different approaches. Moreover, some unsolved scientific problems related to LIPSS are identified and the pending technological limitations are discussed. Hereby, it is intended to stimulate further research and developments in the field of LIPSS for overcoming these limitations and for supporting the transfer of the LIPSS technology into industry T2 - 10th International LIPSS Workshop 2022 CY - Orléans, France DA - 21.09.2022 KW - Laser-induced periodic surface structures (LIPSS) KW - Surface functionalization KW - Femtosecond laser processing KW - Time-resolved coherent scattering PY - 2022 AN - OPUS4-55814 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Balscheit, Hagen T1 - Buckling Behavior of embedded Shells N2 - Presentation on ongoing test campaign on buckling of embedded piles, which is part of the VERBATIM-Project. T2 - Phd Seminar LFU-Innsbruck CY - Innsbruck, Austria DA - 24.06.2022 KW - Buckling KW - Monopiles KW - Windenergy KW - Foundations KW - Offshore PY - 2022 AN - OPUS4-55458 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Linnemann, Konrad T1 - Experimental and numerical investigation of prestressed bolt connections under lateral displacements N2 - The containment system of transport packages for spent nuclear fuel and high-level waste usually includes bolted lids with metal gaskets. The packages are assessed to specific transport conditions which are specified in the IAEA safety standards SSR-6 (IAEA 2018). These transport conditions, especially the so-called accident conditions of transport, imply high dynamic loading on the lids and the bolt connections of the package. The response of the lid systems on the mechanical accident conditions is generally investigated by experimental drop tests or numerically, e.g., by finite element analyses. The interpretation of the drop test results for the verification of the numerical models is often not obvious due to the complex superposition of different effects in the real tests. BAM has started a research project to get a better understanding about the behavior of prestressed bolt connections under loadings typical for these drop tests. In this context an experimental test set-up was developed to investigate the response of a single bolt connection under a prescribed lateral displacement of clamped parts. The bolt is instrumented by strain gauges to get the pretensional, the torsional and the bending stress in the bolt shank. Furthermore, the lateral movement and the tilt of the bolt head is measured during the test. A finite element model of the test set-up has been created in Abaqus FEA (Simulia 2021). The very detailed instrumentation of the test set-up shall give the opportunity to investigate and validate the numerical model. The aim of this paper is to give an overview about the proposed research project and to present first results. T2 - SMIRT26 - 26th International Conference on Structural Mechanics in Reactor Technology CY - Potsdam, Germany DA - 10.07.2022 KW - Transport packages KW - Bolt connections KW - Finite element analysis KW - Experimental investigation PY - 2022 AN - OPUS4-55426 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simbruner, Kai A1 - Billone, M. C. A1 - Zencker, Uwe A1 - Liu, Y. Y. A1 - Völzke, Holger T1 - Brittle Failure Analysis of High-Burnup PWR Fuel Cladding Alloys N2 - The general aim of this research is the development of methods for predicting mechanical behavior and identification of limiting conditions to prevent brittle failure of high-burnup (HBU) pressure water reactor (PWR) fuel cladding alloys. A finite element (FE) model of the ring compression test (RCT) was created to analyze the failure behavior of zirconium-based alloys with radial hydrides during the RCT. An elastic-plastic material model describes the zirconium alloy. The stress-strain curve needed for the elastic-plastic material model was derived by inverse finite element analyses. Cohesive zone modeling is used to reproduce sudden load drops during RCT loading. Based on the failure mechanism in non-irradiated ZIRLO® claddings, a micro-mechanical model was developed that distinguishes between brittle failure along hydrides and ductile failure of the zirconium matrix. Two different cohesive laws representing these types of failure are present in the same cohesive interface. The key differences between these constitutive laws are the cohesive strength, the stress at which damage initiates, and the cohesive energy, which is the damage energy dissipated by the cohesive zone. Statistically generated matrix-hydride distributions were mapped onto the cohesive elements and simulations with focus on the first load drop were performed. Computational results are in good agreement with the RCT results conducted on high-burnup M5® samples. It could be shown that crack initiation and propagation strongly depend on the specific configuration of hydrides and matrix material in the fracture area. T2 - 26th International Conference on Structural Mechanics in Reactor Technology - SMiRT 26 CY - Potsdam, Germany DA - 10.07.2022 KW - Cladding Embrittlement KW - Cohesive Zone Modelling KW - Spent Nuclear Fuel KW - Ring Compression Test PY - 2022 SP - 1 EP - 10 AN - OPUS4-55434 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simbruner, Kai T1 - Brittle Failure Analysis of High-Burnup PWR Fuel Cladding Alloys N2 - The general aim of this research is the development of methods for predicting mechanical behavior and identification of limiting conditions to prevent brittle failure of high-burnup (HBU) pressure water reactor (PWR) fuel cladding alloys. A finite element (FE) model of the ring compression test (RCT) was created to analyze the failure behavior of zirconium-based alloys with radial hydrides during the RCT. An elastic-plastic material model describes the zirconium alloy. The stress-strain curve needed for the elastic-plastic material model was derived by inverse finite element analyses. Cohesive zone modeling is used to reproduce sudden load drops during RCT loading. Based on the failure mechanism in non-irradiated ZIRLO® claddings, a micro-mechanical model was developed that distinguishes between brittle failure along hydrides and ductile failure of the zirconium matrix. Two different cohesive laws representing these types of failure are present in the same cohesive interface. The key differences between these constitutive laws are the cohesive strength, the stress at which damage initiates, and the cohesive energy, which is the damage energy dissipated by the cohesive zone. Statistically generated matrix-hydride distributions were mapped onto the cohesive elements and simulations with focus on the first load drop were performed. Computational results are in good agreement with the RCT results conducted on high-burnup M5® samples. It could be shown that crack initiation and propagation strongly depend on the specific configuration of hydrides and matrix material in the fracture area. T2 - 26th International Conference on Structural Mechanics in Reactor Technology - SMiRT 26 CY - Potsdam, Germany DA - 10.07.2022 KW - Cladding Embrittlement KW - Ring Compression Test KW - Cohesive Zone Modelling KW - Spent Nuclear Fuel PY - 2022 AN - OPUS4-55435 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Linnemann, Konrad A1 - Komann, Steffen A1 - Wille, Frank A1 - Reiche, I. A1 - Ramsay, J. T1 - New Sco-III regulations to ship large objects as surface contaminated objects N2 - The decommissioning or refurbishment of nuclear facilities necessitates either the storage or disposal of large radioactive components such as steam generators, pressurizers, reactor pressure vessels and heads, and coolant pumps, to list the major contributors. These components or objects are large in size and mass, measuring up to approximately 6 meters in diameter, up to 20 meters in length, and weighing over 400 000 kg. In many situations, the components are transported off-site to a storage, disposal or recycling/treatment facility. Previously, many large objects had to be transported under special arrangement. The latest 2018 edition of the International Atomic Energy Agency (IAEA) Regulations for the Safe Transport of Radioactive Material, No. SSR-6 [1], incorporates regulations for the shipment of large objects as a new category of surface contaminated object, SCO-III, based on the IAEA “performance package” concept. This paper provides background and practical guidance on these regulations. Additionally, the experiences of BAM with the appoval of two steam converters of the NPP Lingen are presented as the first approval process for SCO-III objects in Germany. The primary additions to SSR-6 include SCO-III classification and requirements, approval and administrative requirements for the new classification, and the addition of SCO-III to the proper shipping name for UN 2913. Advisory material drafted for the new requirements will be included in the next revision of SSG-26, Advisory Material for the IAEA Regulations for the Safe Transport of Radioactive Material, expected to be published soon. Note that at this time the proposed provisions for large objects do not include components such as reactor vessels, due to the more limited experience and greater radioactivity levels. The SCO-III concept lays the groundwork and may be extended to cover other large objects that are classified as low specific activity (LSA) material in the future. T2 - Kerntechnik 2022 CY - Leipzig, Germany DA - 21.06.2022 KW - Transport packages KW - Radioactive materials KW - SCO-III KW - Large objects PY - 2022 SP - 1 EP - 7 AN - OPUS4-55423 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Linnemann, Konrad T1 - Neue SCO-III Regularien für den Transport grosser Gegenstände als oberflächenkontaminierte Objekte N2 - The decommissioning or refurbishment of nuclear facilities necessitates either the storage or disposal of large radioactive components such as steam generators, pressurizers, reactor pressure vessels and heads, and coolant pumps, to list the major contributors. These components or objects are large in size and mass, measuring up to approximately 6 meters in diameter, up to 20 meters in length, and weighing over 400 000 kg. In many situations, the components are transported off-site to a storage, disposal or recycling/treatment facility. Previously, many large objects had to be transported under special arrangement. The latest 2018 edition of the International Atomic Energy Agency (IAEA) Regulations for the Safe Transport of Radioactive Material, No. SSR-6 [1], incorporates regulations for the shipment of large objects as a new category of surface contaminated object, SCO-III, based on the IAEA “performance package” concept. This paper provides background and practical guidance on these regulations. Additionally, the experiences of BAM with the appoval of two steam converters of the NPP Lingen are presented as the first approval process for SCO-III objects in Germany. The primary additions to SSR-6 include SCO-III classification and requirements, approval and administrative requirements for the new classification, and the addition of SCO-III to the proper shipping name for UN 2913. Advisory material drafted for the new requirements will be included in the next revision of SSG-26, Advisory Material for the IAEA Regulations for the Safe Transport of Radioactive Material, expected to be published soon. Note that at this time the proposed provisions for large objects do not include components such as reactor vessels, due to the more limited experience and greater radioactivity levels. The SCO-III concept lays the groundwork and may be extended to cover other large objects that are classified as low specific activity (LSA) material in the future. T2 - Kerntechnik 2022 CY - Leipzig, Germany DA - 21.06.2022 KW - Transportbehälter KW - Radioaktive Stoffe KW - Oberflächenkontaminiert KW - SCO-III PY - 2022 AN - OPUS4-55424 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lay, Vera T1 - Das Themenfeldprojekt SealWasteSafe im Überblick N2 - Das Projekt SealWasteSafe verbessert Werkstofftechnik, Prüfverfahren und Überwachungsmethoden für sichere Verschlussbauwerke in Endlagern. Dieser Überblick fasst die laufenden Arbeiten in folgenden Bereichen zusammen: 1) Materialentwicklung und Dauerhaftigkeit; 2) Überwachung; 3) Inspektion. T2 - Online-Workshop „Dauerhafte Verschlussbauwerke für Endlager“ CY - Online meeting DA - 14.02.2022 KW - SealWasteSafe KW - Salzbeton KW - Verschlussbauwerke KW - Monitoring KW - Inspektion KW - Ultraschall PY - 2022 AN - OPUS4-55089 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Effner, Ute T1 - Ultraschall-Messungen an in-situ-Abdichtbauwerken mit neu entwickelten Messtechniken N2 - Neue Ultraschall-Messsysteme (LAUS, Bohrlochsonde) haben ihre Funktionstüchtigkeit unter Beweis gestellt. Ergebnisse aus den Messungen konnten verifiziert werden. Standard-Mess- und –Auswerteverfahren müssen für Spritzbeton weiterentwickelt und angepasst werden. Mit sämtlichen Messmethoden konnten großflächige Risse detektiert werden. Messungen mit der Bohrlochsonde und LAUS sind zur Qualitätssicherung geeignet. T2 - Workshop zum TFP-SealWasteSafe CY - Online meeting DA - 14.02.2022 KW - Abdichtbauwerk / Verschlussbauwerk KW - Zerstörungsfreie Prüfung KW - Ultraschall-Echoverfahren PY - 2022 AN - OPUS4-55104 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bischoff, Tristan T1 - Testing and evaluating norms for hot water storage tank efficiency N2 - A round robin test was performed with different laboratories comparing the results for standing heat losses of hot water storage tanks utilizing the current norms for testing. Evaluating these results provides an empirical basis for further developing testing methods. T2 - Conference of young scientists on energy and natural science issues 2022 CY - Kaunas, Lithuania DA - 24.05.2022 KW - Heat storage KW - Standing Losses KW - EU regulations KW - Statistical Analysis KW - Round Robin Test KW - Energy-Label KW - NAPE Project PY - 2022 SN - 2783-6339 SP - 133 EP - 135 AN - OPUS4-55852 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hicke, Konstantin T1 - Distributed fiber optic radiation sensors for nuclear applications N2 - Advantages and underlying principles of distributed fiber optic radiation sensing are discussed. Differences with regard to dose measurement range and resolution between glass optical fiber based sensing and polymer optical fiber based sensing are outlined. T2 - DGZfP SMIRT26 Laborbesuch (BAM) CY - Berlin, Germany DA - 10.07.2022 KW - Distributed fiber optic sensing KW - Fiber optic radiation monitoring KW - Distributed fiber optic radiation sensing PY - 2022 AN - OPUS4-55264 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Caruso, Stefano A1 - Vlassopoulos, Efstathios A1 - Dagan, Ron A1 - Fiorito, Luca A1 - Herm, Michel A1 - Jansson, Peter A1 - Kromar, Marjan A1 - Király, Márton A1 - Leppanen, Jaakko A1 - Feria Marquez, Francisco A1 - Metz, Volker A1 - Papaioannou, Dimitrios A1 - Herranz, Luis Enrique A1 - Rochman, Dimitri A1 - Schillebeeckx, Peter A1 - Seidl, Marcus A1 - Hernandez Solis, Augusto A1 - Stankovskiy, Alexey A1 - Alvarez Velarde, Francisco A1 - Verwerft, Marc A1 - Rodriguez Villagra, Nieves A1 - Zencker, Uwe A1 - Žerovnik, Gasper T1 - EURAD - Work Package 8 - Deliverable 8.1 - State-of-the-art report N2 - A state-of-the-art (SOTA) review on characterisation of spent nuclear fuel (SNF) properties in terms of source term and inventory assessment (neutron, gamma-ray emission, decay heat, radionuclide inventory, elemental content) and in terms of out-of-core fuel performance (cladding performance and fuel integrity in view of the safety criteria for SNF interim storage, transport and canister packaging) using several numerical and experimental approaches and methodologies is presented. This SOTA report is a result of the spent fuel characterisation (SFC) work package as part of the European Joint Programme on Radioactive Waste Management (EURAD), which offers an overview of the status of knowledge in the field of SNF characterisation and assessment during the pre-disposal phase. The document aims to focus on the current safety-significant gaps and related challenges, providing a direct link to the goals of the mandated actors of EURAD. The report is expected to be used by all EURAD colleagues in their national programmes as a key resource for knowledge management programmes and to contribute to demonstrating and documenting the state-of-the-art. KW - Radioactive waste management KW - Spent fuel characterisation KW - Extended interim storage KW - Predisposal PY - 2022 UR - https://www.ejp-eurad.eu/publications/eurad-d81-state-art-report SP - 1 EP - 112 PB - Agence Nationale pour la Gestion des Déchets Radioactifs (ANDRA) CY - Châtenay-Malabry AN - OPUS4-59154 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Pittner, Andreas A1 - Schürmann, Karsten ED - Böhmer, Heike ED - Brinkmann-Wicke, Tanja ED - Sell, Sabine ED - Simon, Janet ED - Tebben, Cornelia T1 - Automatisierte Rohrknotenfertigung in der Offshore-Windenergie – Potenzial zum Leichtbau im schweren Stahlbau N2 - Um den Klimawandel wirksam zu bekämpfen, ist es entscheidend, fossile Brennstoffe durch erneuerbare Energiequellen wie Wind-, Solar- und Wasserkraft sowie alternative Energieträger, beispielsweise grünen Wasserstoff, zu ersetzen. Offshore-Windenergie spielt hierbei eine zentrale Rolle, da sie dank der Kombination aus globaler Verfügbarkeit, relativ geringen Betriebskosten und fortgeschrittenem technischen Entwicklungsstand besonders geeignet ist, zur regenerativen Stromerzeugung beizutragen. Sie ist zudem ein Schlüsselelement für die Umsetzung des Europäischen Green Deals, der das Ziel verfolgt, bis 2050 Klimaneutralität in der EU zu erreichen. Expertenschätzungen zufolge ist eine Steigerung der aktuellen Kapazität von 25 GW im Jahr 2020 auf etwa 450 GW notwendig, um diese ambitionierten Ziele zu erfüllen. Bei der Entwicklung zukünftiger Offshore-Windparks, insbesondere in tieferen Gewässern, gewinnen Jacket-Gründungsstrukturen an Bedeutung. Diese Strukturen, die eine höhere Steifigkeit bei geringerem Materialeinsatz im Vergleich zu den bisher vorherrschenden Monopile-Gründungen bieten, basieren auf komplexen, räumlich aufgelösten Konstruktionen, die ähnlich den Öl- und Gasplattformen entwickelt werden. Die Herstellung der Jacketknoten, die bislang überwiegend manuell geschweißt wurden, birgt erhebliches Optimierungspotential. Durch Automatisierung und Digitalisierung der Fertigungsprozesse könnten nicht nur die Effizienz gesteigert, sondern auch die Qualität der Endprodukte durch präzise Überwachung und Kontrolle der Produktionsparameter verbessert werden. Diese technologischen Fortschritte sind für die Skalierung der Offshore-Windenergie und die Erreichung der Klimaziele von entscheidender Bedeutung. KW - Automatisierte Fertigung KW - Offshore Windenergie KW - Jacket-Gründungsstrukturen KW - Aufgelöste Tragstrukturen KW - Leichtbau PY - 2022 SN - 978-3-7388-0719-6 SP - 260 EP - 266 PB - Fraunhofer IRB Verlag CY - Stuttgart AN - OPUS4-59502 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Linnemann, Konrad A1 - Quercetti, Thomas A1 - Sterthaus, Jens A1 - Ballheimer, Viktor T1 - Experimental and numerical investigation of prestressed bolt connections under lateral displacements N2 - The containment system of transport packages for spent nuclear fuel and high-level waste usually includes bolted lids with metal gaskets. The packages are assessed to specific transport conditions which are specified in the IAEA safety standards SSR-6 (IAEA 2018). These transport conditions, especially the so-called accident conditions of transport, imply high dynamic loading on the lids and the bolt connections of the package. The response of the lid systems on the mechanical accident conditions is generally investigated by experimental drop tests or numerically, e.g., by finite element analyses. The interpretation of the drop test results for the verification of the numerical models is often not obvious due to the complex superposition of different effects in the real tests. BAM has started a research project to get a better understanding about the behavior of prestressed bolt connections under loadings typical for these drop tests. In this context an experimental test set-up was developed to investigate the response of a single bolt connection under a prescribed lateral displacement of clamped parts. The bolt is instrumented by strain gauges to get the pretensional, the torsional and the bending stress in the bolt shank. Furthermore, the lateral movement and the tilt of the bolt head is measured during the test. A finite element model of the test set-up has been created in Abaqus FEA (Simulia 2021). The very detailed instrumentation of the test set-up shall give the opportunity to investigate and validate the numerical model. The aim of this paper is to give an overview about the proposed research project and to present first results. T2 - SMIRT 26 (26th conference on Structural Mechanics in Reactor Technology) CY - Potsdam, Germany DA - 10.07.2022 KW - Bolt connections KW - Finite element anaylsis KW - Experimental testing KW - Transport package for radioactive materials PY - 2022 UR - https://www.lib.ncsu.edu/resolver/1840.20/40614 SP - 1 EP - 7 PB - IASMiRT AN - OPUS4-59378 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin T1 - Fire Reference Tests for Qualification of IAEA Fire N2 - A small cylindrical fire reference package was designed. A fire test setup was created using the fire reference package in accordance with IAEA standards. Four propane gas fire tests were conducted to determine heat fluxes into the fire reference package. The initial test setup was modified to create the final design of the fire test facility. This allowed for the heat flux to be adjusted to meet the regulatory IAEA fire qualification criteria. Furthermore, a numerical model of the fire reference package was created using boundary conditions derived from the experimental data. The simulation results demonstrated good agreement with the experimental data and provided additional insights. T2 - Technical Exchange IRSN – BAM Transport & Storage of Packages for Radioactive Material CY - Cadarache, France DA - 13.10.2022 KW - Fire KW - IAEA KW - Propane PY - 2022 AN - OPUS4-57251 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gerards-Wünsche, Paul T1 - Der Weg vom Labor zur industriellen Einsetzbarkeit der Risslumineszenz N2 - Der Vortrag beschreibt die Relevanz der Zuverlässigkeitsbewertung von klassischen ZfP- und SHM-Verfahren. Diese Zuverlässigkeitsbewertung soll auch für das an der BAM entwickelte Risslumineszenzverfahren durchgeführt werden. Die Risslumineszenz wird zunächst vorgestellt und es wird beschrieben welchen Weg man beschreiten muss, um eine Zuverlässigkeitsbewertung für eine Technik durchzuführen, die nicht nur als ZfP-Verfahren genutzt werden soll, sondern auch für die Dauerüberwachung unter der Einbindung einer KI-basierten automatisierten Risserkennung. Die mit dieser Erweiterung des Einsatzspektrums einhergehenden Faktoren für Messunsicherheit und -variabilität wird als Problematik erkannt und als zukünftige Aufgabe, die es zu lösen gilt, definiert. T2 - ZfP-Seminar Prof. Große TU München WS22 CY - Online meeting DA - 15.12.2022 KW - Rissprozes KW - Structural Health Monitoring KW - Risslumineszenz KW - Ermüdungsprüfung KW - Rissprozess PY - 2022 AN - OPUS4-56643 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stamm, Michael A1 - Krankenhagen, Rainer T1 - EvalTherm - Weather-dependent passive thermography of unheated wind turbine blades N2 - Evaluation of passive Thermography for the inspection of wind turbine blades. Comparison of passive thermography from the ground with drone-supported images and active thermography. Better understand the influence of weather conditions through field measurements. Development of an inspection planning tool that incorporates weather forecasts. Use FEM simulations to predict thermal contrasts of different damages under different environmental conditions. T2 - Kolloquium CY - Saarbrücken, Germany DA - 28.09.2022 KW - Thermography KW - Wind turbine rotor blades KW - FEM PY - 2022 AN - OPUS4-56913 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Das, P. A1 - Chakraborty, Gouri A1 - Roeser, J. A1 - Vogl, S. A1 - Rabeah, J. A1 - Thomas, A. T1 - Integrating Bifunctionality and Chemical Stability in Covalent Organic Frameworks via One-Pot Multicomponent Reactions for Solar-Driven H2O2 Production N2 - Multicomponent reactions (MCRs) can be used to introduce different functionalities into highly stable covalent organic frameworks (COFs). In this work, the irreversible three-component Doebner reaction is utilized to synthesize four chemically stable quinoline-4-carboxylic acid DMCR-COFs (DMCR-1−3 and DMCR-1NH) equipped with an acid−base bifunctionality. These DMCR-COFs show superior photocatalytic H2O2 evolution (one of the most important industrial oxidants) compared to the imine COF analogue (Imine-1). This is achieved with sacrificial oxidants but also in pure water and under an oxygen or air atmosphere. Furthermore, the DMCR-COFs show high photostability, durability, and recyclability. MCR-COFs thus provide a viable materials’ platform for solar to chemical energy conversion. KW - Reactions KW - Bifunctionality KW - Postsynthetic modification KW - Multicomponent PY - 2022 DO - https://doi.org/10.1021/jacs.2c11454 SN - 0002-7863 VL - 145 IS - 5 SP - 2975 EP - 2984 PB - ACS Publications AN - OPUS4-56922 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lay, Vera T1 - Innovations in cemented waste handling and pre-disposal storage (WP7 project PREDIS) N2 - During the webinar "Dismantling and waste management: a playground for innovation" the innovative aspects of the PREDIS work package "innovations in cemented waste handling and pre-disposal storage" are presented. The webinar is jointly organised by Women in Nuclear Decommissioning (WINDI) and Women in Nuclear Innovation (WINI). The shown innovations include quality assurance (mainly NDE) and monitoring technologies with associated sensor systems, digital twin technology, and appropriate data handling including a decision framework. An overview of the on-going research in the field of pre-disposal waste management in the project Predis (WP7) is summarised. T2 - Webinar "Dismantling and waste management: a great playground for innovation" CY - Online meeting DA - 13.10.2022 KW - Predis KW - Waste management KW - Concrete PY - 2022 AN - OPUS4-56926 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger T1 - Container requirements for high-level radioactive waste disposal in rock salt, claystone, and crystalline rock – Outcomes of the research project KoBrA N2 - Suitable containers for receiving high-level radioactive waste are a key elements of every repository system concerning different host rocks like rock salt, claystone and crystalline rock as being considered in Germany. The disposal container design is decisive regarding boundary conditions for the transport, emplacement techniques, and the operational and long-term safety assessment. The systematic derivation of the requirements to be placed on disposal containers forms the basis for a targeted, comprehensible and transparent development of containers that meet the requirements. The presentation summarizes the outcomes of the research project KoBrA. T2 - IGD-TP Symposium CY - Zurich, Switzerland DA - 20.09.2022 KW - Disposal KW - Container KW - Radioactive waste KW - Safety PY - 2022 AN - OPUS4-57021 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liepold, Philipp T1 - Anwendung von CNNs zur verbesserten Auswertung von MVT-Tests N2 - Durch die Anwendung von Convolutional Neural Networks (CNNs) kann die Auswertung von Modifizierten Varestraint-Transvarestraint-Tests (MVT) erheblich verbessert werden. Im MVT-Test werden Proben während des Schweißvorgangs über einen Zylinder gebogen. Die auf der Oberfläche der Probe sichtbare Rissstruktur gibt über Parameter wie die Gesamtrisslänge Auskunft über die Erstarrungsrissbeständigkeit der verwendeten Kombination aus Grundstoff, Schweißzusatz und Schweißparametern. Jedoch kann eine Auswertung unter dem Mikroskop sehr aufwendig sein und je nach Beobachter unterschiedliche Ergebnisse liefern. Mit Hilfe von CNNs wird die Auswertung der Risse automatisiert was Genauigkeit, Geschwindigkeit und Vergleichbarkeit verbessert. T2 - BMDK CY - Magdeburg, Germany DA - 05.12.2022 KW - CNN KW - MVT KW - KI PY - 2022 AN - OPUS4-56839 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rieck, Arielle A1 - Schwarz, Irina T1 - Electrochemical CO2 reduction (CO2RR) coupled to gas fermentation with acetogenic bacteria N2 - For the realization of a sustainable energy economy, it is of great importance to develop CO2 -neutral methods producing multi-carbon organic chemicals used as feedstock in the chemical industry as well as carbon-neutral fuels. A promising method to alleviate the greenhouse effect and thereby forming value-added chemicals or syngas as an energy carrier, is through the electrochemical CO2 reduction reaction (CO2RR). In this work, a bioelectrotechnological approach is developed, in which the CO2RR reaction products (CO and H2) are directly fed to bacteria (acetogens), who use them as “reduction equivalents” to further metabolize CO2 to valuable carbon compounds. Therefore, a bio-electrochemical system consisting of a bioreactor coupled to a CO2 electrolysis cell will be established. Currently, scarce catalysts such as Ag and Au are used as for the CO2RR which may hamper the use of decentral CO2 conversion technology for cost reasons. The technological viability of the bacteria-assisted electrolysis depends on the usage of efficient, biocompatible, and selective electrocatalysts prepared from inexpensive precursors. Porous transition metal and nitrogen co-doped carbons (M-N-Cs) have emerged as precious-metal free electrocatalysts for the direct electrochemical reduction of CO2 into CO and are excellent candidates for scale-up and deployment in technological applications. Furthermore, Co/Ni/Zn functioning as the catalytically active sites will be used, as they are expected to depict non-bactericidal properties in contrast to Cu and Ag catalysts. The non-bactericidal property could e.g., allow for application within the hybrid device (bio-electrochemical system), without the need to separate bacteria and cathode catalyst. The MNCs with the most promising electrocatalytic activity and selectivity will be evaluated in abiotic conditions in the hybrid bio-electrochemical reactor system. T2 - DFG Summer School Workshop CY - Hamburg, Germany DA - 01.09.2022 KW - Katalysator KW - CO2 Reduktion KW - Bioelectrochemical CO2 reduction PY - 2022 AN - OPUS4-56618 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rieck, Arielle A1 - Schwarz, Irina T1 - Valorization of CO2 by electrocatalytic reduction coupled to acetogens via multiple electron carriers (Ecat-acetogens) N2 - For the realization of a sustainable energy economy, it is of great importance to develop CO2 -neutral methods producing multi-carbon organic chemicals used as feedstock in the chemical industry as well as carbon-neutral fuels. A promising method to alleviate the greenhouse effect and thereby forming value-added chemicals or syngas as an energy carrier, is through the electrochemical CO2 reduction reaction (CO2RR). In this work, a bioelectrotechnological approach is developed, in which the CO2RR reaction products (CO and H2) are directly fed to bacteria (acetogens), who use them as “reduction equivalents” to further metabolize CO2 to valuable carbon compounds. Therefore, a bio-electrochemical system consisting of a bioreactor coupled to a CO2 electrolysis cell will be established. Currently, scarce catalysts such as Ag and Au are used as for the CO2RR which may hamper the use of decentral CO2 conversion technology for cost reasons. The technological viability of the bacteria-assisted electrolysis depends on the usage of efficient, biocompatible, and selective electrocatalysts prepared from inexpensive precursors. Porous transition metal and nitrogen co-doped carbons (M-N-Cs) have emerged as precious-metal free electrocatalysts for the direct electrochemical reduction of CO2 into CO and are excellent candidates for scale-up and deployment in technological applications. Furthermore, Co/Ni/Zn functioning as the catalytically active sites will be used, as they are expected to depict non-bactericidal properties in contrast to Cu and Ag catalysts. The non-bactericidal property could e.g., allow for application within the hybrid device (bio-electrochemical system), without the need to separate bacteria and cathode catalyst. The MNCs with the most promising electrocatalytic activity and selectivity will be evaluated in abiotic conditions in the hybrid bio-electrochemical reactor system. T2 - DFG Summer School Workshop CY - Hamburg, Germany DA - 01.09.2022 KW - CO2 Reduktion KW - MNC catalyst KW - Clostridium ragsdalei PY - 2022 AN - OPUS4-56619 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kolmangadi, Paulina T1 - Molecular dynamics of nanophase-separated Janus polynorbornenes by neutron scattering, dielectric spectroscopy, and fast scanning calorimetry N2 - The structure and molecular dynamics of a homologous series of Janus polytricyclononenes (PTCN) with rigid backbones and flexible n-alkyl (n = propyl, butyl, hexyl, octyl) side groups were studied. These polymers are novel, innovative materials that show potential in separating hydrocarbons. Janus PTCNs were designed to show an enhanced and controllable gas permeability via flexible alkyl side chains that promote mass transport, as opposed to conventional microporous polymers, where permeability is a function of the free-volume entities. The materials, studied by small angle X-ray scattering (SAXS), show nanophase separation between the n-alkyl side chains and the backbones. The size of the nanodomains increases with the length of the n-alkyl side groups. In addition, for the alkyl chain-rich nanodomains a distinct α-relaxation (dynamic glass transition) was found by means of broadband dielectric spectroscopy (BDS) and temperature modulated DSC (TMDSC). The glass transition of the backbone-rich domains, which is beyond or near to the degradation of the materials, was evidenced by fast scanning calorimetry (FSC) by decoupling it from decomposition by employing high heating rates up to 104 K/s. Janus PTCNs were studied by quasielastic neutron scattering employing the backscattering instrument IN16B. For an overview of dynamic processes setting in at different temperatures inelastic (IFWS) and elastic fixed window scans (EFWS) were conducted. IFWS showed that the segmental motions of alkyl-rich nanodomains shift to higher temperatures with increasing alkyl chain length, which agrees with SAXS and BDS findings. For the lowest side chain lengths an additional low temperature relaxation process was found, assigned to methyl group rotations. T2 - QENS / WINS 2022 CY - San Sebastian, Spain DA - 23.05.2022 KW - Gas separation KW - Membranes PY - 2022 AN - OPUS4-55898 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Szymoniak, Paulina T1 - Molecular Dynamics of nNanophase-Separated Janus Polynorbornenes for gas separation N2 - Janus polytricyclononenes (PTCN) with rigid backbones and flexible n-alkyl (n = propyl, butyl, hexyl, octyl, decyl) are novel, innovative materials that show potential in separating hydrocarbons. These superglassy polymers were designed to show an enhanced and controllable gas permeability via flexible alkyl side chains that promote mass transport, as opposed to conventional microporous polymers, where permeability is a function of the free-volume entities. PTCNs, investigated by small angle X-ray scattering (SAXS), show nanophase separation between the n-alkyl side chains and the backbones. The size of the nanodomains increases with the length of the n-alkyl side groups. In addition, for the alkyl chain-rich nanodomains a distinct α-relaxation was found by means of broadband dielectric spectroscopy (BDS) and temperature modulated DSC (TMDSC). The glass transition of the backbone-rich domains, which is beyond or near to the degradation of the materials, was evidenced by fast scanning calorimetry (FSC) by decoupling it from decomposition, employing high heating rates up to 104 K/s. Further, Janus PTCNs were studied by quasielastic neutron scattering (QENS) employing the backscattering IN16B (ILL, Grenoble) and time of flight FOCUS (PSI, Villigen) instruments. For an overview of dynamic processes setting in at different temperatures inelastic (IFWS) and elastic fixed window scans (EFWS) were conducted. IFWS showed that the segmental motions of alkyl-rich nanodomains shift to higher temperatures with increasing alkyl chain length, which agrees with SAXS and BDS findings. For the lowest side chain lengths an additional low temperature relaxation process was found, assigned to methyl group rotations. T2 - IDS 2022 CY - San Sebastian, Spain DA - 03.09.2022 KW - Gas separation KW - Membranes PY - 2022 AN - OPUS4-55899 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -