TY - CONF A1 - Widjaja, Martinus Putra T1 - Effect of the time dependent loading of type IV cylinders using a multiscale model N2 - Based on the burst test results conducted at BAM, loading rates will affect the strength of composite pressure vessels (CPV). The multiscale fibre-break model developed at Mines ParisTech is able to described this behaviour explained by the stress relaxation in the viscoelastic matrix. The experiment showed an increase of burst pressure when an extreme slow loading rate is used compare to the slow loading rate. Is is then discovered that the model could predict well for the slow loading rate but not for the extreme slow loading rate. It may have something to do with the fibre re-orientation of the hoop layer during the extreme slow loading rate test. Further investigation is required to discover this hypothesis. T2 - International Conference on Hydrogen Safety CY - Adelaide, Australia DA - 24.09.2019 KW - Composite pressure vessels KW - Fibre break KW - Multiscale model KW - Time dependent effect PY - 2019 AN - OPUS4-50262 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Widjaja, Martinus Putra T1 - Effect of input properties on the predicted failure of a composite pressure vessel using a multiscale model N2 - The effect of different Weibull parameter from different carbon fibres to predict the failure of a type IV pressure vessel has been analysed. In addition, the effect of the shape and scale parameter has also been done. T700S fibres gave higher burst pressure prediction as it has higher scale parameter and higher stiffness of the fibres. When smaller scale parameter is introduced, lower burst pressure prediction was found and vice versa. Whereas, higher burst pressure prediction was observed when smaller shape parameter was used and vice versa. The latter must have something to do with the higher probability of stronger and weaker fibres in the smaller percentile. T2 - FiBreMoD Conference CY - Leuven, Belgium DA - 11.12.2019 KW - Composite pressure vessel KW - Fibre break KW - Multiscale model KW - Weibull parameters PY - 2019 AN - OPUS4-50115 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zaghdoudi, Maha A1 - Kömmling, Anja A1 - Jaunich, Matthias A1 - Wolff, Dietmar T1 - Scission, cross-linking, and physical relaxation during thermal degradation of elastomers N2 - Elastomers are susceptible to chemical ageing, i.e., scission and cross-linking, at high temperatures. This thermally driven ageing process affects their mechanical properties and leads to limited operating time. Continuous and intermittent stress Relaxation measurements were conducted on ethylene propylene diene rubber (EPDM) and hydrogenated nitrile butadiene rubber (HNBR) samples for different ageing times and an ageing temperature of 125 °C. The contributions of chain scission and cross-linking were analysed for both materials at different ageing states, elucidating the respective ageing mechanisms. Furthermore, compression set experiments were performed under various test conditions. Adopting the two-network model, compression set values were calculated and compared to the measured data. The additional effect of physical processes to scission and cross-linking during a long-term thermal exposure is quantified through the compression set analysis. The characteristic times relative to the degradation processes are also determined. KW - Ageing KW - Scission KW - Cross-linking KW - Compression set KW - Physical relaxation PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-486091 DO - https://doi.org/10.3390/polym11081280 SN - 2073-4360 VL - 11 IS - 8 SP - 1280, 1 EP - 12 PB - MDPI AN - OPUS4-48609 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kömmling, Anja T1 - Research at BAM for evaluating long term safety of container systems and components N2 - Safety of long term containment and storage of radioactive waste is an essential issue, which is increasingly gaining international attention. Extending interim storage beyond initial license periods is one of the major challenges worldwide. BAM has been involved in all kinds of radioactive waste container safety evaluation for storage and transportation including their long term performance from the very beginning. Today, all work related to the safe management of radioactive waste is linked by the activity field “Nuclear Waste Management” within the Focus Area “Energy” at BAM and in conjunction with a research strategy and agenda. Most recently, the working group “Long Term Safety of Container Systems and Components” was established to launch and perform research projects related to safety issues concerning the extended interim storage of radioactive waste. For example, within our project LaMEP, we investigate ageing effects of metal and elastomer seals as well as polymeric neutron shielding materials, which are container components that fulfil major safety functions. The results of the experiments help to understand the long term behaviour of these components. Likewise, our project BRUZL started at BAM in 2018 with the aim of developing a fracture mechanics approach to understand and describe a potential brittle failure mechanism of fuel cladding during long-term interim storage. BAM also contributes to the GRS project “Development of methods and models and international exchange for safety evaluation in the frame of interim storage of radioactive waste”. Additionally, BAM is involved in several international research programmes dealing with extended interim storage, such as the European Joint Programme on Radioactive Waste Management (EURAD), the Extended Storage Collaboration Program (ESCP) and IAEA Coordinated Research Projects. The present contribution provides a comprehensive overview of BAM research activities contributing to national and international gap analyses and to filling knowledge gaps regarding the safe long term management of radioactive waste. T2 - Annual Meeting on Nuclear Technology 2019 CY - Berlin, Germany DA - 07.05.2019 KW - Radioactive Waste KW - Container Safety KW - Metal Seals KW - Elastomer Seals KW - Fuel cladding PY - 2019 AN - OPUS4-48437 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo A1 - Roohbakhshan, Farshad T1 - Cyclic Operation Performance of 9-12% Cr Ferritic-Martensitic Steels. Part 2: Microstructural Evolution during Cyclic Loading and its Representation in a Physically-based Micromechanical Model N2 - The current trend towards cyclic, “flexible” operation of fossil-fueled power plants constitutes a major issue regarding lifetime and operational safety of the respective installations and their components, as was outlined in our complementary contribution (Part 1). The present contribution reports on the investigation of the microstructure evolution in cyclically loaded ferritic-martensitic steels and its representation in a physically-based micromechanical model. For this purpose, specimens of P92 steel grade from the mechanical test programme outlined in our companion contribution (Part 1) were analyzed by scanning electron microscopy (SEM), including backscattered diffraction (EBSD) mapping, and transmission electron microscopy (TEM). A novel method was implemented to improve angular resolution of EBSD scans. Additionally, a correlative microscopy approach was developed and used to correlate EBSD and TEM measurements on the same locations of thick regions of electron transparent specimens. By applying these techniques, a detailed quantitative microstructure description of the as-received material condition, namely in terms of subgrain morphology and dislocation density/distributions, was established. Comparisons of as-received and cyclically loaded conditions from tests interrupted at different stages of lifetime indicate a rapid redistribution of in-grain dislocations with a strong interaction between mobile dislocations and low angle grain boundaries (LABs). The proposed micromechanical model is formulated in a viscoplastic self-consistent (VPSC) scheme, which is a mean-field approach that allows us to include the crystal details at the level of slip systems while avoiding the considerable computational costs of full-field approaches (such as the classical crystal plasticity finite element analysis). Being physically-based, the model uses dislocation densities and includes the interaction between dislocations, e.g. annihilation of mobile dislocations, and evolution of microstructure, e.g. the grain coarsening. Particularly, the constitutive laws for dislocation evolution and interaction between dislocations and low angle boundaries are calibrated based on two-dimensional discrete dislocation dynamic (2D DDD) simulations, which are performed at a micro-/meso-scale. The results of the beforementioned EBSD experiments are considered as a direct input, involving e.g. the amount of geometrically necessary dislocations, average misorientations and grain characteristics. T2 - 45th MPA-Seminar 2019 CY - Leinfelden-Echterdingen, Germany DA - 01.10.2019 KW - Tempered martensite ferritic steel KW - Dislocation KW - Electron backscattered diffraction (EBSD) KW - Transmission electron microscopy (TEM) KW - Microstructure KW - Physically based material model PY - 2019 AN - OPUS4-49346 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Widjaja, Martinus Putra A1 - Alves, M. A1 - Mavrogordato, M. A1 - Joannes, S. A1 - Bunsell, A. A1 - Mair, Georg W. A1 - Thionnet, A. T1 - Effect of the Time Dependent Loading of Type IV Cylinders Using a Multiscale Model N2 - The Reduced Volume Method (RVM) has been used to evaluate the multiscale fibre break model developed at Mines ParisTech. It allows the model to be assigned only at certain part of the structures without necessarily compromising the final prediction. An attempt to model a simple unidirectional composite structure has also been carried out and gave a satisfying result. This paper deals with the application of the RVM to real scale type IV composite cylinders, where its stacking sequence was evaluated through micro-CT scans conducted with the collaboration of the University of Southampton. Two modelling geometries were evaluated and compared with the corresponding experimental results. T2 - 8th International Conference on Hydrogen Safety (ICHS) CY - Adelaide, Australia DA - 24.09.2019 KW - Fibre break KW - Multiscale modelling KW - Type IV pressure vessel KW - Time dependent loading PY - 2019 SP - ID131 AN - OPUS4-49273 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wang, Bin T1 - Introduction of numerical methods to simulate damage accumulations of composite pressure vessel N2 - The development of hydrogen as a reliable energy sector is strongly connected to the performance and the level of safety of hydrogen storage system. Composite damage due to static, fatigue loading and ageing effect is a progressive process. The common failure modes of composite pressure vessels are majorly fibre break, then interface debonding, matrix cracking and delamination. The damages occur subsequently or even simultaneously, failure modes may interactive each other. These attributes make the composite fatigue more complex and difficult. The presentation here is to show how the numerical methods being developed to match this challenge, particularly the numerical model of composite pressure vessel developed by FibreMod research project is introduced. The potential role of numerical simulation in the certification process and the outlook for the further trend is also discussed. T2 - Abteilungskolloquium CY - BAM Berlin, Germany DA - 10.05.19 KW - Fibre Break KW - Composite Pressure KW - Vessels KW - Simulation PY - 2019 AN - OPUS4-48302 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Widjaja, Martinus Putra T1 - Accumulation of fibre breaks in racetrack specimens and type IV pressure vessels N2 - The reduced volume method has been studied using the fibre break model from Mines ParisTech. This method allows less 3D finite elements to be used for predicting the failure of real scale composite structures. A favourable comparison results with racetrack specimens has been achieved. However, the comparison study with a type IV pressure vessels still requires more Evaluation. T2 - Consortium Meeting FiBreMoD CY - Toyota Motor Europe, Belgium DA - 27.03.2019 KW - Reduced volume method KW - Integral range KW - Multiscale model KW - Fibre break KW - Composite pressure vessels KW - Racetrack specimens PY - 2019 AN - OPUS4-48571 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias T1 - Dichtungsverhalten bei niedrigen Temperaturen - Untersuchung der unteren Temperatureinsatzgrenze von Elastomerdichtungen - N2 - Elastomere werden vielfach in Produkten eingesetzt, die bei verschiedenen Temperaturen verwendet werden. O-Ringe sind kostengünstige Dichtelemente, die allerdings für die Funktionsfähigkeit und Sicherheit eines Produkts entscheidend sein können. Die untere Temperatur-einsatzgrenze ist dabei relevant und aus wissenschaftlicher Sicht nicht allgemein gültig zu definieren, da diese einerseits durch die Änderungen der Materialeigenschaften im Zuge des Gummi-Glas-Übergangs definiert werden, die Temperaturlage dieses Übergangs jedoch sehr stark von den jeweiligen Einsatzbedingungen (z.B. Frequenz) abhängt. Dadurch ergeben sich große Unterschiede zwischen statischen und dynamischen Anwendungen. Verschieden Untersuchungen sollen vorgestellt und interpretiert werden, um das Auditorium auf verschiedene Herausforderungen aufmerksam zu machen und Lösungsansätze vorzustellen. T2 - ISGATEC Forum Werkstoffe 2019 CY - Mannheim, Germany DA - 03.12.2019 KW - Dichtung KW - O-Ring KW - Tiefe Temperaturen KW - Versagenstemperatur PY - 2019 AN - OPUS4-49983 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zaghdoudi, Maha T1 - Overview of ongoing long-term ageing investigations on elastomer seals N2 - At the Bundesanstalt für Materialforschung und -prüfung (BAM) in Division 3.4 Safety of Storage Containers, one of our tasks is to evaluate the safety of containers designed for disposal of low and intermediate radioactive waste. As such containers might be transported before and stored until disposal, safe enclosure of the radioactive inventory is important for this time span. Elastomer O-rings are widely used as barrier seals in these containers. Thus, as for many other applications, an understanding of the practical effects of ageing degradation on elastomer seals during long-term exposure is mandatory for predicting the lifetime of such components. According to a long-term test programme on three kinds of rubbers (EPDM and FKM (relevant for application), HNBR (for comparison)), over several years we have studied the degradation and the change of mechanical properties (e.g. hardness, strain at break) at four different ageing temperatures (75 °C, 100 °C, 125 °C and 150 °C) as well as the change of sealing properties. Continuous and intermittent compression stress relaxation (CSR) measurements were performed in order to investigate the respective contribution of crosslinking and chain scission to the observed degradation effects. Thus, the degradation kinetics and mechanisms could be resolved more clearly. For assessing the seal performance, compression set (CS) and leakage rate measurements were conducted. The experimental results showed that the O-rings remained leak-tight under purely static conditions even when CSR, CS and mechanical properties already indicated far advanced degradation. For this reason, a modified leakage test involving a small and rapid partial decompression of the seal was developed that enabled determining an end-of-lifetime criterion for O-rings with a safety margin for thermal shrinkage and vibrations. T2 - IRC CY - London, UK DA - 03.09.2019 KW - Compression set KW - Continuous compression stress relaxation KW - Intermittent compression stress relaxation KW - Leakage rate PY - 2019 AN - OPUS4-49073 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -